eSpace_IAD104H&132E(T)&196&1224_V300R002C01SPCm00_Upgrade_Guide

eSpace IAD104H&132E(T)&196&1224 V300R002C01SPCm00

Upgrade Guide

Issue

01

Date

2017-03-06

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2017. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other tradem arks and trade names mentione d in this document are the property of their th eir respecti respect i ve holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representation representations s o f any any k ind, ind, either exp ress or implied. implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations recommend ations in this document docum ent do not constitute constit ute a warranty of any kind, express express or implied.

Hua Hua wei Techno Techno logies Co., Ltd. Address:

Huawei Indust rial Base Bantian, Bantian, Longgang Shenzhen 518129 People's Republic of China

Website:

http://e.huawei.com

Issue 01 (2017-03-06) (201 7-03-06)

Huawei Prop rietary rietary and Confiden Confiden tial Copyright © Huawei Technologies Co., Ltd.

i

Copyright © Huawei Technologies Co., Ltd. 2017. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other tradem arks and trade names mentione d in this document are the property of their th eir respecti respect i ve holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representation representations s o f any any k ind, ind, either exp ress or implied. implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations recommend ations in this document docum ent do not constitute constit ute a warranty of any kind, express express or implied.

Hua Hua wei Techno Techno logies Co., Ltd. Address:

Huawei Indust rial Base Bantian, Bantian, Longgang Shenzhen 518129 People's Republic of China

Website:

http://e.huawei.com

Issue 01 (2017-03-06) (201 7-03-06)

Huawei Prop rietary rietary and Confiden Confiden tial Copyright © Huawei Technologies Co., Ltd.

i

eSpace IAD104H&132E(T)&196&1224 IAD104H&132E(T)&196&1224 Upgrade Guide

Contents Conten ts

Contents 1 Before You Start............................. Start...................................................... .................................................. .................................................. .............................................. ..................... 1 1.1 Upgrad Upg radee Sche Sch e mes ..................................................................................... .......................................................................................1 1.2 Ap plicab pl icab le Vers ions ion s ................................................................................................ .........................................................................1 1.2.1 Version Upgrade Path ..................................................................................................................................................................1 1.3 Impact of the Upgrade.....................................................................................................................................................................2 1.4 Precautions ........................................................................................................................................................................................2 1.5 V300R0 02C01 02C0 1 Series Se ries Version ers ion Special Spec ial Notes.......... Note s................ ............ ............. ............. ............. ............. ............ ............. ............. ............. ............. ............ ............. .............. ............. ............ ............ ............. ........3 .3

2 Preparing for the Upgrade...................................... Upgrade........................................................... .............................................. ................................................ ....................... 4 2.1 Obtaining Obta ining the th e V300R00 30 0R002C01S 2C01SPC PCm00 m00 Soft So ftware ware Package Packag e ............ ................... ............. ............ ............. ............. ............. ............. ............ ............. ............. ............. ............. ............ ............. ........4 .4 2.2 Ver ifying ify ing Softwa Soft ware re Integ Int egrr ity ................................................................................................ ..........................................................4 2.3 Obtain Obt aining ing Upg rade rad e Tools .............................................................................................. ..................................................................5 2.4 Querying the Current IAD Version ...............................................................................................................................................5 2.5 Obtaining Obta ining the th e Softwa So ftware re Pac kage of the t he Current IAD Version ers ion ............. ................... ............ ............ ............. .............. ............. ............ ............. ............. ............. ............. ............ ............ .........5 ...5 2.6 Backing Back ing Up Data ....................................................................................... .......................................................................................5 2.6. 1 Enablin Enab ling g the th e FTP or T FTP Service Serv ice .......................................................................................... ..................................................5 2.6.2 Backing Up a Sys tem Conf iguration igura tion File ............. ................... ............ ............ ............. .............. ............. ............ ............. ............. ............. ............. ............ ............. ............. ............. ............. ............ ............ ........8 ..8 2.6. 3 Backing Back ing Up User Us er In for mation ................................................................................................ ....................................................9 2.7 Querying Query ing the th e Number Nu mber o f On line Users Use rs ............ ................... ............. ............ ............. ............. ............. ............. ............ ............. ............. ............. ............. ............ ............. ............. ............. ............. ............ ............. .......10 10

3 Perfor P erforming ming the Upgrade in CLI Manual Mode.................... Mode ............................................ ................................................. ......................... 11 3.1 Upgrad Upg rading ing the th e Hos t Software Soft ware ................................................................................................ ......................................................11 3.1. 1 IA D1224/ D12 24/196 196 up grade gra de BOOT1 BOOT 1 ............................................................................................... .................................................11 3.1.2 Upgrading Upg rading the th e Hos Ho s t Software to the th e inter in ter im Ve Ve rsion ............ .................. ............. ............. ............. ............. ............ ............ ............. .............. ............. ............ ............ ............. .............. ............1 .....11 1 3.1.3 Upgrade to the target version....................................................................................................................................................12 3.2 Upgradin Upgra ding g Boot1 Boo t1 (FTP On ly) ................................................................................................ ......................................................12 3.2.1 Upgrade Upg rade BOOT1 Using the th e Device CLI ............. ................... ............ ............ ............. .............. ............. ............ ............ ............. .............. ............. ............ ............. ............. ............. ............. ............ ............ .......13 .13 3.2.2 Upgrade Upg rade BOOT1 Using the th e Boot1 Boot 1 CLI ............. ................... ............ ............ ............. .............. ............. ............ ............ ............. ............. ............. ............. ............ ............. .............. ............. ............ ............ .........14 ...14

4 Verifying Verifying the Upgrade .......................................................... .................................................................................. ................................................. ............................. .... 16 4.1 Ver ifying ify ing th e Software Soft ware Ve rsion rs ion ................................................................................................ ....................................................16 4.2 Ver ifying ify ing Calls Ca lls ................................................................................................ ................................................................................16

5 Rolling Back B ack to the Source Version.................... Version ............................................. .................................................. ............................................ ................... 17 5.1 Rolling Rollin g Back Bac k the th e IAD132 IAD 132E(T) E(T) fro m BIOS ............. ................... ............ ............ ............. .............. ............. ............ ............. ............. ............. ............. ............ ............. ............. ............. ............. ............ ............1 ......17 7

Issue 01 (2017-03-06)

Huawei Huawei Proprietary Proprietary and Confidential Confidential Copyright © Huawei Technologies Co., Ltd.

ii

eSpace IAD104H&132E(T)&196&1224 Upgrade Guide

Contents

5.1. 1 Preparations ................................................................................................ .................................................................................17 5.1.2 Operation Procedure ..................................................................................................................................................................17 5.2 Ver ifying th e Rollback ................................................................................................ ..................................................................20

6 Solution to Upgrade Failures .................................................................................................... 21 6.1 Preparations ....................................................................................................................................................................................21 6.2 Procedure.........................................................................................................................................................................................21 6.2.1 Logging In t o t he IAD Through the Local Se rial Port .........................................................................................................21 6.2.2 Configuring the FTP Server......................................................................................................................................................21 6.2.3 Restarting the IAD .....................................................................................................................................................................21 6.2. 4 Loading the PTS Fi le ................................................................................................ .................................................................22 6.3 Ver ification ................................................................................................ ......................................................................................23

A Web Manual Upgrade ............................................................................................................... 24 A.1 FTP Mode.......................................................................................................................................................................................24 A.2 HTTP Mode ...................................................................................................................................................................................25

B Automatic Upgrade .................................................................................................................... 27 B.1 Web Mode ......................................................................................................................................................................................27 B.2 CLI Mode .......................................................................................................................................................................................28

Issue 01 (2017-03-06)

Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

iii


1 Before You Start

1

Before You Start

1.1 Upgrade Schemes The eSpace Integrated Access Device (IAD) provides the following upgrade schemes: (Note that upgrade from V300R001C06 or V300R001C07 to V300R002C01 series version can be performed only in command-line interface (CLI) manual mode.) 

CLI manual mode This mode allows the manual upgrade of a single IAD, which is used for upgrading a small number of IADs. For details, see chapter "3 Performing the Upgrade in CLI Manual Mode".



Web manual mode This mode allows the manual upgrade of a single IAD, which is used for upgrading a small number of IADs. For details, see appendix "A Web Manual Upgrade."



Automatic mode This mode allows the batch upgrade of IADs, which is used for upgrading a large number of IADs in web or CLI mode. For details, see appendix "B Automatic Upgrade. "



Network management mode For details about how to upgrade IADs in network management mode, see the network managementhelp.

1.2 Applicable Versions 1.2.1 Version Upgrade Path If current version is V300R002C01 series version, please refer to the following procedure:

Issue 01 (2017-03-06)

Huawei Prop rietary and Confiden tial Copyright © Huawei Technologies Co., Ltd.

1


1 Before You Start

If current version is V300R001C07 series version, please refer to the following procedure:

In the preceding figure, versions include R and C versions, and the SPC versions are not provided. For example, if the version queried on the CLI is IAD V300R001C07SPC200, the version is IAD V300R001C07.

1.3 Impact of the Upgrade During the upgrade, the IAD services will be interrupted for about 10 minutes, and the communication between the IAD and the network management system (NMS) will also be interrupted for about 10 minutes. You are advised to perform the upgrade during off-peak hours.

1.4 Precautions 

The V300R002C01 series version file is ts1224.pts for the IAD1224 and ts0196.pts for the IAD196.



To upgrade the IAD from V300R001C06 to V300R002C01 series version, you must first upgrade it to V300R001C06SPC100 and then to V300R002C01series version. The version span is large, and you must load two different version files. For details, see section "1.2 Applicable Versions"



If you upgrade the IAD from V300R001 series versions to V300R002C01series version, data may be lost due to a large version span. Before the upgrade, you must back up the IAD configuration files and user information files.



Only the IAD1224 can be upgraded from V300R001 to V300R002. The IAD104H and IAD132E(T) cannot be upgraded to V300R002 due to hardware restrictions.



Upgrading from a previous version to version V300R002C01SPCm00, you need to load interim version, otherwise the data will be lost.

Issue 01 (2017-03-06)


2


1 Before You Start



IAD196 and IAD1224, upgrade from a previous version to V300R002C01SPC200, you must first upgrade BOOT1 then upgraded interim version, and then upgrade host version, and how to upgrade BOOT1 method see section 3.2



Interim version V300R002C01SPC100U only used in the upgrade process data smooth upgrade, can not as a long-running target version.



Because of the IAD save SNMPV3's password and the default user has defects, upgrade to a new version, SNMPV3's password and the default user data will be lost, please backup SNMPV3's password and the default user information before upgrading.



Because V300R002C01SPCm00 enhances the user login password protection, from the version back to the previous version, the login password will expire, must restore the device to factory default values, please be careful on version rollback.



IAD1224 upgrades from version V300R002C01 to version V300R001C07, the following parameters?? default values ??will change to the default value of version V300R002C01 (Please have a look at the version??s supporting information to get the default values?? Details) system soft-parameter http-switch system soft-parameter telnet-sw itch nms getcom nms setc om nms trapcom Acc ount login password



When the upgrade version, IAD104H need to connect the network through the WAN port, IAD196/1224 need to connect to the network through the FE1 port.



During the upgrade, you can neither power off the host nor disconnect or shut down the File Transfer Protocol (FTP), File Transfer Protocol over SSL (FTPS), or Trivial File Transfer Protocol (TFTP) server.

1.5 V300R002C01 Series Version Special Notes 

When you upgrade the IAD from an earlier version to V300R002C01 series version, the version span is large, and the upgrade process is complicated. You must read the upgrade guide carefully.



After you upgrade the IAD from an earlier version to V300R002C01 series version, the default password of the root user is changed from admin to huawei123.



To upgrade the IAD1224 from V300R001 series version to V300R002C01 series version, you must run the load packet force { ftp ip user-name password | ftps ip user-name password | tftp ip } file-name command to forcibly upgrade the IAD. IAD196, IAD132E(T), IAD104H only V300R002C01 versions can upgrade to V300R002C01SPCm00, the remaining version can not be upgraded.



IAD1224 / 196 new hardware (version number: CH51VCVPA. VC) can not be loaded V300R002C01SPC500 and previous software versions.



Upgrade IAD1224 / 196 devices Boot1, system startup process will automatically upgrade Boot2, please Boot2 file into the FTP / FTPS / TFTP directory.



TS1224.pts or TS0196.pts contain Boot2 program, when loaded PTS file, Boot2 are simultaneously upgraded.



Hardware version number is AG11CVP VER.D of IAD132E(T), it can not be loaded into V300R002C01SPCc00 previous version.

Issue 01 (2017-03-06)


3


2

2 Preparing for the Upgrade

Preparing for the Upgrade

2.1 Obtaining the V300R002C01SPCm00 Software Package You can obtain the V300R002C01 software package at http://support.huawei.com/enterprise/. To download software, you must apply for a login account and password in advance. The path for downloading the software package is as follows: Support > Downloads > UC&C > Enterprise Cloud Communications > CloudUC > IP Phone & Soft Terminals > eSpace IAD > V300R002C01SPCm00

The following shows the directory structure of the software package. Upgrade software for different IAD models is stored in different folders. Select the correct software based on the directory structure. IAD V300R002C01SPCm00 |-IAD 1224 |-IAD 196 |-IAD 132E(T) |-IAD 104H

2.2 Verifying Software Integrity . After obtaining the software in the preceding section, verify the software integrity. If the integrity check is not passed, obtain the correct software. For the software obtaining procedure, see 2.1 Obtaining the V300R002C01SPCm00 Software Package . Do not load incorrect software to the device, which may compromise the device. Support-E: The digital signature and digital signature authentication guide are released on http://support.huawei.com/enterprise/ together with the system software package. Click the software installation package to obtain the corresponding digital signature, and click Digital Signature Authentication Mode to obtain the authentication method. Support: The digital signature PGP and digital signature authentication guide can be downloaded on the same web page as the system software package. Download them and click Digital Signature Authentication Mode to obtain the authentication method.

Issue 01 (2017-03-06)


4



2.3 Obtaining Upgrade Tools Obtain the FTP/FTPS/TFTP server tools. You are advised to use the 3CDaemon (FTP or TFTP) and FileZilla Server (FTPS), which can be downloaded from the Internet free of charge.

2.4 Querying the Current IAD Version Log in to the IAD using Telnet. Enter the user name ( root by default) and password ( admin or huawei123 by default), and then run the enable command to enter the privilege mode. Run the display version command to query the IAD version, and then record the queried IAD version number ( Program version value).

2.5 Obtaining the Software Package of the Current IAD Version Normally, if the upgrade fails, the original version of the IAD remains unc hanged, and you can upgrade the IAD again or use the original version. If exceptions occur during the upgrade and the IAD of the original version cannot be used, you must load the original version again. You need to obtain the current software version in advance. For details, see section "2.1 Obtaining the V300R002C01SPCm00 Software Package."

2.6 Backing Up Data Before the upgrade, you must back up the IAD configuration files and us er information files. The following describes the procedures for backing up the IAD configuration files and user information files thr ough commands.

2.6.1 Enabling the FTP or TFTP Service The FTP or TFTP tool is used for transmitting files. This section uses the 3CDaemon as an example to describe how to enable the FTP/TFTP service.

Enabling the FTP Service Step 1 Start the 3CDaemon. The main page of the 3CDaemon is displayed, as shown in Figure 2-1.

Issue 01 (2017-03-06)


5



Figure 2-1 Main page of the 3CDaemon

The right pane displays the status of connections, data upload, and data download in real time.

Step 2 Click FTP Server on the left pane, and then click Configure FTP Server. The FTP Profiles tab page is displayed, as shown in Figure 2-2.

Issue 01 (2017-03-06)


6



Figure 2-2 FTP Profiles tab page

Step 3 Set FTP parameters on the FTP Profiles tab page. 1.

Set the user name to iad.

2.

Click Set/Change user's password, and then set the password to huawei.

3.

Set C:\ for storing files.

4.

Select all check boxes in the This user can area.

5.

Click Save Profile to save the settings.

Step 4 Check whether the FTP server is installed s uccessfully. 1.

Open Internet Explorer.

2.

Enter the IP address of the FTP server, for example, ftp://192.168.100.2 in the address box, and then press Enter

If the message "FTP Folder Error " is displayed, ignore the error. Choose File > login As in the menu bar, and enter the set user name and password in the Log On As dialog box. 3.

If the folder can be opened, the FTP server is installed successfully. Otherwise, check whether the 3CDaemon is correctly configured. Then restart the 3CDaemon.

----End

Issue 01 (2017-03-06)


7



Enabling the TFTP Service Step 1 Start the 3CDaemon. Step 2 Click TFTP Server on the left pane, and then click Configure TFTP Server. The TFTP Configuration tab page is displayed, as shown in Figure 2-3. Figure 2-3 TFTP Configuration tab page

Step 3 Set C:\ for storing files and set other parameters as shown in Figure 2-3. ----End

2.6.2 Backing Up a System Configuration File Before backing up data, run the ping command to check whether the PC where the FTP or TFTP server is located and the IAD are connected. If the ping command times out, check the network configuration. For example, check whether the IP address, subnet mask, and gateway are set correctly and whether an IP address or MAC address conflict exists.

Backup Command Run the following command in global configuration mode: backup < config | users> {ftp ip user-name password | ftps ip user-name password | tftp ip } file-name

Parameters in the preceding command are described as follows: 

config: indicates to back up a system configuration file.



users : indicates to back up a SIP user information file.



ip: IP address of the PC where the FTP, FTPS, or TFTP service is running.



user-name: name of an FTP or FTPS user.



password : password of an FTP or FTPS user.



file-name: name of a backup file.

Issue 01 (2017-03-06)


8



Backup Procedure Example The following uses a system configuration file as an example to describe the backup procedure.

Step 1 Log in to the IAD using Telnet. Enter the user name ( root bydefault) and password ( admin or huawei123 bydefault), and then run the enable command to enter the privilege mode. Run the configure terminal command to enter the global configuration mode.

Step 2 Back up the system configuration file. 

If the FTP service is enabled, run the following command: TERMINAL(config)#backup config ftp 192.168.100.2 iad huawei iad_config.txt



If the FTPS service is enabled, run the following command: TERMINAL(config)#backup config ftps 192.168.100.2 iad huawei iad_config.txt



If the TFTP service is enabled, run the following command: TERMINAL(config)#backup config tftp 192.168.100.2 iad_config.txt

The backup system configuration file that is stored to the preset path on the FTP, FTPS, or TFTP server. ----End

2.6.3 Backing Up User Information Backing Up a SIP User Information File For all versions later than IAD V300R001C06, run the backup users command to back up a SIP user information file. 

If the FTP service is enabled, run the following command: TERMINAL(config)#backup users ftp 192.168.100.2 iad huawei sip_user.txt Online backup file now... Download Stage: File dump

& Rate of process: 100%

Backup file result:success! //Indicates that backup is successful. 

If the FTPS service is enabled, run the following command: TERMINAL(config)#backup users ftps 192.168.100.2 iad huawei sip_user.txt Online backup file now... Download Stage: File dump


Backup file result:success! //Indicates that backup is successful. 

If the TFTP service is enabled, run the following command: TERMINAL(config)#backup users tftp 192.168.100.2 sip_user.txt Online backup file now... Download Stage: File dump


Backup file result:success! //Indicates that backup is successful.

Issue 01 (2017-03-06)


9



2.7 Querying the Number of Online Users Online IAD users include voice users and data users. 

Run the display pstnport state command in global configuration mode to query the status of voice users. The Idle state indicates that users are not making calls, and the Busy state indicates that users are making calls.

You are advised to upgrade the IAD when few users are online.

Issue 01 (2017-03-06)


10


3

3 Performing the Upgrade in CLI Manual Mode

Performing the Upgrade in CLI Manual Mode

3.1 Upgrading the Host Software 3.1.1 IAD1224/196 upgrade BOOT1 Must be upgraded to boot1:3.2 Upgrading Boot1 (FTP Only)

3.1.2 Upgrading the Host Software to the interim Version Step 1 Enable the FTP or TFTP service. For details, see section "2.6.1 Enabling the FTP or TFTP Service"

Step 2 Copy the interim version file to be loaded to the preset path on the FTP or TFTP server, for example, C:\.

Step 3 Run the load packet {ftp ip user-name password | ftps ip user-name password | tftp ip} file-name command to upgrade the IAD. To upgrade the IAD from V300R001C06 or V300R001C07 to V300R002C01 series version, run the load packet force {ftp ip user-name password | ftps ip user-name password | tftp ip} file-name command. For example with V300R001C07SPC700 version(The same applies V300R002C01SPC100):

Step 4 Log in to the IAD using Telnet. Enter the user name ( root bydefault) and password ( admin or huawei123 bydefault), and then run the enable command to enter the privilege mode. Run the diagnose command to enter the diagnose mode. 

If the FTP service is enabled, run the following command: TERMINAL(diagnose)%%load packet force ftp 192.168.100.2 iad huawei

TS1224_Interim.pts 

If the FTPS service is enabled, run the following command: TERMINAL(diagnose)%%load packet force ftps 192.168.100.2 iad huawei

TS1224_Interim.pts 

If the TFTP service is enabled, run the following command: TERMINAL(diagnose)%%load packet force tftp 192.168.100.2 TS1224_I nterim.pts

The following information is displayed after the upgrade is complete: NOTICE:Only r eboot system,new program can take e ffect!

Issue 01 (2017-03-06)


11



Step 5 Run the reboot command to r estart the IAD for the configuration to take effect. TERMINAL(diagnose)#reboot Are you sure to reset system? Caution:Unsaved data will be lost![Y|N]:y System will reboot in 5 seconds!

It takes about 5 minutes to restart the IAD. After the IAD is restarted, log in to the IAD again and query the IAD version. If the version is V300R002C01SPC100U, the upgrade is successful. ----End

3.1.3 Upgrade to the target version Step 1 Log in to the IAD using Telnet. Enter the user name ( root bydefault) and password ( admin or huawei123 bydefault), and then run the enable command to enter the privilege mode. Run the config command to enter the config mode.

If the FTP service is enabled, run the following command:



TERMINAL(diagnose)%%load packet force ftp 192.168.100.2 iad huawei TS1224.pts

If the FTPS service is enabled, run the following command:



TERMINAL(diagnose)%%load packet force ftps 192.168.100.2 iad huawei TS1224.pts

If the TFTP service is enabled, run the following command:



TERMINAL(diagnose)%%load packet force tftp 192.168.100.2 TS1224.pts


Step 2 Run the reboot command to r estart the IAD for the configuration to take effect. TERMINAL(diagnose)#reboot Are you sure to reset system? Caution:Unsaved data will be lost![Y|N]:y System will reboot in 5 seconds!

It takes about 5 minutes to restart the IAD. After the IAD is restarted, log in to the IAD again and query the IAD version. If the version is V300R002C01SPCm00, the upgrade is successful. ----End

3.2 Upgrading Boot1 (FTP Only) Boot1 upgrade involves two situations: 

If the Boot1 version is 204 or later, upgrade Boot1 using the device CLI. For details, see "3.2.1 Upgrade BOOT1 Using the Device CLI3.2.1 Upgrade BOOT1 Using the Device CLI".



If the Boot1 version is earlier than 204, upgrade Boot1 using the Boot1 CLI. For details, see "3.2.2 Upgrade BOOT1 Using the Boot1 CLI3.2.2 Upgrade BOOT1 Using the Boot1 CLI".

During its start, the board prints the version number of Boot1. The following is an example.

Issue 01 (2017-03-06)


12



In this example, the version of Boot1 is 208. The other way to kown the version of BOOT1,you can execute the commd :display version ;for example the BOOT1 version is 305.

3.2.1 Upgrade BOOT1 Using the Device CLI Step 1 Enable the FTP service. For details, see "2.6.1 Enabling the FTP or TFTP Service ". Step 2 Copy the bootrom_cvp_ppc8321.bin software to be loaded to the directory set for the FTP server, for example, C:\.

Step 3 Run the auto-update ftpserver [] command to set the FTP loading parameters in the boot process.

Step 4 Run the system soft-parameter autoload-boot1 on command to enable automatic upgrade of bootrom_cvp_ppc8321.bin during the next restart. ----End

V300R001C07SPC700 is used as an example. The following steps also apply to V300R002C01SPC100: 1.

Log in to the IAD using Telnet. Enter the user name and password. The default user name is root and the default password is admin or huawei123.

2.

Run the enable command to access the privilege mode, and then run the config command to access the config mode

3.

TERMINAL(config)#auto-update ftps erver 192.168.100.8 cvp cvppass (Set the FTP parameters based on actual conditions.)

4.

Run the advanced command to access the advanced mode.

5.

TERMINAL(advanced-c onfig)#system soft-parameter autoload-boot1 on

6.

Run the exit command to exit the config mode.

Issue 01 (2017-03-06)


13


7.


Run the reboot command. During the device restart, bootrom_cvp_ppc8321.bin is automatically loaded.

3.2.2 Upgrade BOOT1 Using the Boot1 CLI Step 1 Enable the FTP service. For details, see "2.6.1 Enabling the FTP or TFTP Service ". Step 2 Copy the bootrom_cvp_ppc8321.bin software to be loaded to the directory set for the FTP server, for example, C:\.

Step 3 Run the auto-update ftpserver [] command to set the FTP loading parameters in the boot process.

Step 4 Run the system soft-parameter autoload-boot1 on command to restart the system. After the restart, the board automatically enters Boot1 mode.

Step 5 Observe the printed information. When the "Press "D" or "d" to stop auto boot..." message is displayed, press d to access the Boot1 CLI. On the Boot1 CLI, run the imgUpgradeByFtp 1 command to load the Boot1 file. Then, restart the board to complete the loading. The following gives an example of step 5: BOOT1 Version:201 CPLD Version:105 FPGA Version:103 Creation Time:Apr

8 2011, 09:22:44

WDB Comm Type: WDB_COMM_END WDB: Ready. Bios update flag is b1055555 Both area are the same! Press "D" or "d" to stop auto boot...

d (Press d to access the shell.) Auto boot is stopped. Burnin test has been done before,Skip burnin test! Enter CVP BASIC BOOTROM! CVP boot1-> CVP boot1->imgUpgradeByFtp 1 (Run the imgUpgradeByFtp 1 command to upgrade Boot1.) Using default parameter from bootline! host IP

: 3.2.20. 61

user name

: cvp

ftp

: cvppass

password

file name

Issue 01 (2017-03-06)

: bootrom_c vp_ppc8321.bin


14



Starting imgUpgrade may break the bootrom,will you start it? (input 'Y' or 'y' to start,others to abort)

y (P ress y to continue the upgrade operation.) Setup ftp Connection to retrieve bootrom_cvp_ppc8321.bin..... Loading File from Host ......

Done

Done

Clear ExtBootrom valid flag ............. Done

(Observe the loading result. In this example, the loading is successful.) value = 0 = 0x0 CVP boot1->reboot (Restart the board to complete the Boot1 loading.) Reboot reset s ystem! ----End

Issue 01 (2017-03-06)


15


4 Verifying the Upgrade

4

Verifying the Upgrade

4.1 Verifying the Software Version Log in to the IAD using Telnet. Enter the user name ( root bydefault) and password ( huawei123 bydefault), and then run the enable command to enter the privilege mode. Run the display version command to view the IAD version.

Expected Result The queried IAD version is the same as the target version.

Troubleshooting Upgrade the IAD again according to the related sections.

4.2 Verifying Calls Make intra-office calls and inter-office calls.

Expected Result IAD users can call each other and the voice quality is satisfactory.

Troubleshooting See chapter 6 Solution to Upgrade Failures"6 Solution to Upgrade Failures" to rectify the fault.

Issue 01 (2017-03-06)


16


5

5 Rolling Back to the Source Version

Rolling Back to the Source Version

5.1 Rolling Back the IAD132E(T) from BIOS 5.1.1 Preparations 

Obtain the software package of the version before upgrade. For details, see 2.1 Obtaining the V300R002C01SPCm00 Software Package you need.



Enable the FTP service. The TFTP service is not supported for version rollback. For details, see "2.6.1 Enabling the FTP or TFTP Service ".



Putting the software package into the storing files which is set in the FTP server, for example, C:\.

5.1.2 Operation Procedure To roll back to the IAD132E(T) version, do as follows:

Loading the BIOS file Step 1 Log in to the IAD through the local serial port. Connect the IAD's console port to the PC's serial port using the serial cable. Choose Start > All Programs > Accessories > Communications > Hyper Terminal and select COM1 in the Connect To dialog box. (If the login fails, select COM2.) In the COM Properties dialog box, click Reset Defaults and click OK . Press Enter on the main page. On the displayed welcome page, enter the user name root and password huawei123 to enter the common user mode.

Step 2 Power off and on the IAD. When "Please press CTRL+B to enter bootmenu, other key to boot!" is displayed, press Ctrl+B within five seconds to access the BIOS setup menu. Please press CTRL+B to enter bootmenu,other key to boot! remain

4s

Welcome to bootmenu! Rebuild from the main config area! init config area success! BIOS password (<=20 chars):

Step 3 Enter the BIOS password to access BOOT MENU. The default password is qpmz1234.

Issue 01 (2017-03-06)


17



======================= BOOT MENU ======================= 1.Enter equipment submenu 2.Enter download submenu 3.Boot system from flash R.Reset Enter your choice(1-3 or R):

Step 4 View the IP address of the IAD. Choose 2.Enter download submenu > 2. IP configuration submenu > 3. Display IP configuration to view the IP address of the IAD, for example. IP(V4) ADDRESS: 192.166.1.120.

Step 5 Configure the FTP server. Choose R to return to the download submenu. Then choose 1.FTP server configuration submenu > 1.FTP server configuration to configure the parameters of FILE SERVER NAME, FTP LOGIN USER NAME and FTP LOGI N PASSWORD , and others keep default. =============================== FTP SERVER CONFIGURATION =============================== You can press CTRL+D to clear. FILE SERVER NAME:

192.168.1.101//IP address of the FTP server

FTP LOGIN USER NAME: iad

iad//user name for logging in to the FTP server

FTP LOGIN PASSWORD: huawei

huawei//password for logging in to the FTP server

DEFAULT FTP FILE PATH: .

.//The default value is .

Save FTP server configuration to flash... done. ======================== FTP SERVER SUBMENU ======================== 1.FTP server configuration 2.Display FTP server configuration R.Return upper menu Enter your choice(1-2 or R):

Step 6 Choose R to return to the download submenu. Choose 4.Download BIOS to display the file loading page. Enter iad_bios to start loading the file. Enter load BIOS file name(default TS3202.bios) :

File Server: 192.168.1.101 File path:

.

Filename:

TS3202.bios

Username:

iad

Password:

huawei

Protocol:

0

programTransfer::ftpXfer succeed. File length: 675725 bytes Connected to file server, start receiving(press CTRL+C to break)................ ................................................ done.

Issue 01 (2017-03-06)


18



Check program file...... done. Save boot image...Now S tart BIOS len = 675668 ..............................Now End BIOS len = 675668 done.

Restart the IAD immediately after loading the BIOS file. Otherwise, the BIOS may be damaged. After the BIOS file is loaded, choose R to return to BOOT MENU. Then choose R again to restart the IAD for the configuration to take effect. It takes about two minutes to restart the IAD. ----End

Loading the PTS file Step 1 Press Ctrl+B to access the BIOS during the system restart. password is manager. ----End

The disp layed BIOS page may be differs from that displayed before the BIOS file is loaded. ======================= BOOT MENU ======================= 1.Enter equipment submenu 2.Enter download submenu 3.Boot system from flash R.Reset

Step 1 Step 2 Choose 2. Enter download submenu > 2.IP configuration submenu > 3.Display IP configuration to view the IP address of the IAD.

The IP address of the IAD may be changed after the BIOS file is loaded. Before loading the *.pts file, ensure that the IP address of the FTP server and the new IP address of the IAD can be pinged.

Step 3 Choose R to return to the upper menu, and then choose 2.Enter download submenu > 2.IP configuration submenu > 2. IP configuration to set the IP address of the IAD.

Step 4 under??FTP SUBMENU?? menu??choose ??1.FTP server configuration ??set ??FILE SERVER NAME??????FTP LOGIN USER NAME??????FTP LOGIN USER PASSWORD??field value??others are default .

Issue 01 (2017-03-06)


19



============================= FTP PARAMETER CONFIGURATION ============================== You can press CTRL+D t o clear FILE SERVER NAME:192.168.100.2

FTP SERVER ADDRESS

FTP LOGIN USER NAME??iad FTP LOGIN USER PASSWORD??huawei

FTP SERVER USERNAME FTP SERVER PASSWORD

DEFAULT FTP FILE PATH: FTP server configuration to RAM... done.

Step 5 under??FILE DOWNLOAD SUBMENU?? menu??choose ??3. Download system application??LOAD PTS FILE??

Step 6 After the *.pts file is loaded, choose R to return to BOOT MENU. Then choose R again to restart the IAD for the configuration to take effect. It takes about two minutes to restart the IAD. ----End

5.2 Verifying the Rollback Procedure Step 1 Log in to the IAD using Telnet. Enter the user name ( root bydefault) and password ( admin or huawei123 bydefault), and then run the enable command to enter the privilege mode. Run the display version command to view the IAD version. Verify that the queried IAD version is the same as the source version.

Step 2 Make intra-office calls and inter-office calls. Verify that calls can be made properly. ----End

Expected Result 

The queried IAD version is the same as the source version.



IAD users can call each other and the voice quality is satisfactory.

Troubleshooting 

Perform version rollback again according to the description in this chapter.



See section Troubleshooting in the IAD Product Documentation.

Issue 01 (2017-03-06)


20


6

6 Solution to Upgrade Failures

Solution to Upgrade Failures

6.1 Preparations Obtain the software to be loaded. For details, see section"2.1 Obtaining the V300R002C01SPCm00 Software Package."

6.2 Procedure 6.2.1 Logging In to the IAD Through the Local Serial Port Use a serial cable to connect console port on the IAD to a serial port on a PC. Choose Start > All Programs > Accessories > Communications > Hyper Terminal and select COM1 in the Connect To dialog box. (If the login fails, select COM2.) In the COM Properties dialog box, click Reset Defaults and click OK .

6.2.2 Configuring the FTP Server Step 1 Change the IP address of the PC. The default IP address is 192.168.100.8. Specify the IP address according to the actual serial port information displayed during the IAD restart.

Step 2 Start the FTP server software on the PC. The TFTP service is not supported for BIOS mode. For details, see section "2.6.1 Enabling the FTP or TFTP Service "

Step 3 Set both the user name and password on the FTP server software. Place the software of the version that is being used in the home directory. The default user name and password are iadephone and enable respectively. Specify the user name and password according to the actual serial port information displayed during the IAD restart.

Step 4 Connect the PC to the FE1 port on the IAD. ----End

6.2.3 Restarting the IAD The IAD automatically loads the CVP.bin file during the restart. If host ip and IAD ipaddress not in the same subnet ,you must add two ipaddress for pc which is FTP server so that ,IAD can ping FTP server .for example IAD ipaddress is 3.2.30.167 gatway ip address is 3.2.30.254

Issue 01 (2017-03-06)


21



host ip is 10.177.19.199,you must add the two ipaddress for PC ,one is 3.2.30.254 ,the other 10.177.19.199.

During the IAD restart, the following s erial port information is displayed: auto-booting... host IP

: 192.168.1.100

user name

: iadephone

ftp

: enable

password

file name

: cvp.bin

Setup Ftp Connection to retrieve cvp.bin.....

6.2.4 Loading the PTS File After the IAD is restarted, log in to the IAD again and load the PTS file for the target version.

Step 1 Enter the user name ( root by default) and password ( admin or huawei123 bydefault) to access the IAD configuration page.

Step 2 Enter enable and press Enter to access the privileged mode. Step 3 Enter diagnose and press Enter to access the diagnose mode. Step 4 Run the load packet force { ftp ip user-name password | ftps ip user-name password | tftp ip} file-name command to upgrade the IAD. Parameter

Description

ip

IP address of the PC where the FTP or TFTP service is running.

user-name

FTP user name.

password

Passw ord of an FTP user.

file-name

Name of the file to be loaded.



If the FTP service is enabled, run the following command: TERMINAL#load packet force ftp 192.168.100.2 iad huawei TS1224.pts



If the FTPS service is enabled, run the following command: TERMINAL#load packet force ftps 192.168.100.2 iad huawei TS1224.pts



If the TFTP service is enabled, run the following command: TERMINAL#load packet force tftp 192.168.100.2 TS1224.pts


Step 5 Run the reboot command to restart the IAD for the configuration to take effect.

Issue 01 (2017-03-06)


22



TERMINAL#reboot Are you sure to reset system? Caution:Unsaved data will be lost![Y|N]:y System will reboot in 5 seconds!

It takes about 2 minutes to restart the IAD. After the IAD is restarted, log in to the IAD again. ----End

6.3 Verification Procedure Step 1 Enter the user name ( root bydefault) and password ( huawei123 bydefault), and then run the enable command to enter the privilege mode. Run the display version command to view the IAD version. Verify that the queried IAD version is the same as the source version.

Step 2 Make intra-office calls and inter-office calls. Verify that calls can be made properly. ----End

Expected Result 

The queried IAD version is the same as the target version.



IAD users can call each other and the voice quality is satisfactory.

Issue 01 (2017-03-06)


23


A Web Manual Upgrade

A

Web Manual Upgrade

A.1 FTP Mode The upgrade procedure is as follows:

Step 1 Copy the target version file to be loaded to the preset path on the FTP server, for example, C:\.

Step 2 Enable the FTP service. For details, see section 2.6.1 "Enabling the FTP or TFTP Service." Step 3 Open Internet Explorer, enter the IAD IP address in the address box, and press Enter. The login page is displayed, as shown in the following figure.

Step 4 Set the system language to English. Enter the user name and password and click Login. By default, the user name is root, the password is admin or huawei123.

Step 5 Choose Maintenance > Upgrade Version. The version upgrade page is displayed.

Step 6 Select FTP.

Issue 01 (2017-03-06)


24



Step 7 Selecting the FTP mode

Step 8 Set parameters according to Table A-1 and then click OK to update the IAD.

During the upgrade, do not operate the IAD. The process takes about 2 minutes. After the update is complete, restart the IAD as prompted. Table A-1 FTP server parameters

Parameter

Description

FTP server IP address

IP address of the PC where the FTP service is running.

User name

User name for logging in to the FTP server.

Password

Password for logging in to the FTP server.

Version file name

Name of the version file to be loaded (for example, TS1224.PTS ).

----End

A.2 HTTP Mode The upgrade procedure is as follows:

Step 1 Copy the target version file to be loaded to a local directory, for example, D:\. Step 2 Open Internet Explorer, enter the IAD IP address in the address box, and press Enter. The login page is displayed, as shown in the following figure.

Issue 01 (2017-03-06)


25



Step 3 Set the system language to English. Enter the user name and password and click Login. By default, the user name is root, the password is admin.

Step 4 Choose Maintenance > Upgrade Version, and select HTTP on the version upgrade page, as shown in Figure A-2. Selecting the HTTP mode

Step 5 Click Browse to select file to be loaded or directory enter the file name with its directory in the text box.

During the upgrade, do not operate the IAD.

Step 6 Click OK to update the IAD. The process takes about 2 minutes. After the update is complete, restart the IAD as prompted. ----End

Issue 01 (2017-03-06)


26


B Auto matic Upgrade

B

Automatic Upgrade

B.1 Web Mode The upgrade procedure is as follows:

Step 1 Make the update_info.txt file. For details, see Step 2 in section B.2 "CLI Mode." Step 2 Copy the target version file to be loaded and the update_info.txt file to the preset path on the FTP server, for example, C:\.

Step 3 Enable the FTP service. For details, see section 2.6.1 "Enabling the FTP or TFTP Service." Step 4 Open Internet Explorer, enter the IAD IP address in the address box, and press Enter. The login page is displayed, as shown in the following figure.

Step 5 Set the system language to English. Enter the user name and password and click Login. By default, the user name is root, the password is admin.

Step 6 Choose Maintenance > Automatic Upgrade . The automatic upgrade page is displayed, as shown in Figure B-1.

Issue 01 (2017-03-06)


27



Figure B-1 Automatic upgrade page

Step 7 Set Auto-upgrade switch to On. Step 8 Set other parameters according to Table B-1, and then click OK . After the configuration is complete, the IAD will periodically check the version on the FTP server. If the device version is inconsistent with the version on the FTP server, the IAD upgrades automatically. Table B-1 FTP server parameters

Parameter

Description

FTP server IP address

IP address of the PC where the FTP service is running.

User name


Password


File directory

Relative path for logging in to the FTP server. The default value is . (indicates the directory set in the FTP software).

Auto-upgrade Interval

Interval for checking for a new upgrade package.

After the upgrade is successful, the system restarts and displays the welcome page automatically. During the restart, do not operate the IAD.

Step 9 On the displayed welcome page, enter the user name root and password admin to log in to the system. Choose Basic Configuration > Version Information to confirm that the version is the latest version. ----End

B.2 CLI Mode Automatic upgrade supports only the FTP server. The TFTP server is not supported.

Issue 01 (2017-03-06)


28



The upgrade procedure is as follows:

Step 1 Enable the FTP service. For details, see section 2.6.1 "Enabling the FTP or TFTP Service."

Step 2 Make the update_info.txt file. Using this file, IADs of certain versions can be upgraded automatically.

Step 3 The file contains one or more lines. The upgrade is started if any of the lines is matched. The file allows multiple products to be upgraded on the same FTP server at the same time. The format of each line is as follows: %Product name% =%File name of the program to be loaded%/ old_version=% Product name+Source version%

Parameter

Description

Remarks

%Product name%

Product name of the IAD to be upgraded, for example, TS1224.

Case sensitive

%File name of the program to be loaded%

File name of the upgrade package to be loaded, for example, TS1224.pts .

Case insensitive

%Product name+Source version%

Product name and source version. For example, if the product name is TS1224 and the version is V300R002C01SPC100, the value is TS1224V300R002C01SPC100.

Case sensitive

Step 4 Make the update_info.txt file according to the original version to be upgraded, and then copy the file to the loading directory on the FTP server. Assume that the TS1224V300R002C01SPC100 needs to be upgraded.

Run the display version command to query the current version. The message "Product name: TS1224 Program version: V300R002C01SPC100" is displayed. Match the preceding version information strictly in the update_info.txt file. TS1224=TS1224_Interim.pts / old_version=TS1224V300R002C01SPC100 //Name of the product to be upgraded is TS1224; version number is V300R002C01SPC100 ; file name of the software package to be loaded is TS1224_Interim.pts .

Step 5 Copy the interim version file TS1224.pts to the loading directory on the FTP server. Step 6 Run the auto-update command to enable automatic upgrade. After automatic upgrade is enabled, the IAD checks whether the upgrade conditions are met at intervals according to the contents of each line in the update_info.txt file. If yes, the upgrade is started. The following table describes the commands for automatic upgrade.

Issue 01 (2017-03-06)


29



Operation

Command

Set the user name, password, and default path for logging in to the FTP server.

TERMINAL(config)#auto-update ftpserver ip username password [director]

Set the interval for checking whether the upgrade conditions are met.

TERMINAL(config)# auto-update detect-interval interval

The following table describes the parameters in the preceding commands.

Parameter

Description

ip

IP address of the PC where the FTP or TFTP service is running.

username


password


(Optional) directory

Relative path for logging in to the FTP server. The default value is . (indicates the directory set in the FTP software). You are not advised to set this parameter.

interval

Interval for chec king for a new upgrade package, in seconds. The value ranges from 60 to 86400, and the default value is 3600. You can also set this parameter to 0 to disable automatic upgrade.

For example, the IAD uses the user name iad and password huawei to log in to the FTP server whose IP address is 192.168.100.2 and checks whether a new upgrade package exists every 600 seconds. If yes, the automatic upgrade is started. The procedure is as follows: 1.

Set the interval for checking for a new upgrade package. TERMINAL(config) #auto-update detect-interval 600

2.

Enable the automatic check function. TERMINAL(config) #auto-update ftpserver 192.168.100.2 iad huawei The following alarm information is displayed when the IAD starts downloading the upgrade package: ! EVENT WARNING 2005-01-01 00:10:58 ALARM NAME :Online load start PARAMETERS :Load content: config

After the upgrade is successful, the system restarts and displays the welcome page automatically. During the restart, do not operate the IAD.

Issue 01 (2017-03-06)


30

eSpace_IAD104H&132E(T)&196&1224_V300R002C01SPCm00_Upgrade_Guide

Recommend Documents