Dynalite Installers Course Training Guide

Installers Course Training Guide Advanced lighting controls made easy

Version 1.1

Background Philips Dynalite is a highly specialized company whose principal occupation is to provide ‘cutting edge’ solutions for lighting control. Our achievements have been recognized worldwide and Philips Dynalite is generally the system of choice for projects involving integration with thirdparty vendor’s equipment and for large-scale applications. Philips Dynalite’s philosophy is to provide the best solution possible for each and every project. This is the key to our success. Our considerable investment in Research & Development ensures that we remain at the forefront of our industry. Our position as a world leader in lighting management systems for the future is sustained through our total commitment to innovation. We are represented around the world by distributors and dealers who are handpicked for their ability to provide the highest possible level of service.

From a stock exchange in Shanghai, to a luxury resort in Dubai, a smart home in Sao Paulo to limestone caves in New Zealand, Philips Dynalite’s innovative solutions deliver intelligent light. Ongoing research and development has enabled Philips Dynalite to create secure automated systems that control tens of thousands of individual light fittings in high-rise office buildings from any location anywhere in the world. Our networks are engineered to deliver instant notification of power or system failure, and report via a LAN, internet, or through an SMS gateway to a mobile phone. This provides the assurance necessary in applications where continuous operation is vital, such as road tunnels, computer servers or cold storage units. Philips Dynalite’s modular product design philosophy also improves system flexibility. Through this approach, specific application requirements can be accommodated with greatly reduced lead times. As an industry leader Philips Dynalite is committed to creating superior lighting control and energy management systems, setting new benchmarks in performance and efficiency. In receiving the International Association of Lighting Designers award for Most Innovative Product, the Philips Dynalite control system has been independently recognized as ‘A user friendly and sensible modular approach, which takes it from sophisticated domestic settings to large architectural spaces’.

2

Installers Course User Guide

Topic 1: Infrastructure

Contents Topic 1: Infrastructure .......................................................................................................................... 9 Overview............................................................................................................................................................................... 9 Learning outcomes ......................................................................................................................................................... 9 Cabling ................................................................................................................................................................................... 9 Networking requirements ............................................................................................................................................ 9 CAT 5 cable limits ........................................................................................................................................................ 10 CAT 5 wiring diagram .................................................................................................................................................. 11 Recommended DyNet color coding for CAT5 cable .......................................................................................... 11 Recommended DyNet CAT 5 data cable types .................................................................................................... 12 Belden wiring diagram .................................................................................................................................................. 12 Recommended DyNet color coding for Belden cable ......................................................................................... 13 S-Flat 6 cable limits ....................................................................................................................................................... 13 Recommended DyNet color coding for S-Flat 6 cable ........................................................................................ 14 Pin out conversion for RJ45 cable testers............................................................................................................... 14 RJ12 socket connections ............................................................................................................................................. 14 Termination ........................................................................................................................................................................ 15 CAT5 Instructions ........................................................................................................................................................ 15 Flat cable instructions .................................................................................................................................................. 22 DyNet voltages .................................................................................................................................................................. 22 Network architecture ...................................................................................................................................................... 23 The DyNet Network ................................................................................................................................................... 23 The Physical Layer ........................................................................................................................................................ 23 Trunk & spur network ..................................................................................................................................................... 24 Implementing trunk & spur topology ....................................................................................................................... 24 Trunk & spur network ................................................................................................................................................. 25 DLight III trunk &spur network ................................................................................................................................. 26 Ethernet networks ............................................................................................................................................................ 27 Multi trunk networks ................................................................................................................................................... 28 Network cable current limits and voltage drop ........................................................................................................ 29 HF Ballast installation ....................................................................................................................................................... 30 Installation instructions ................................................................................................................................................ 30 DyNet 1 & 2 networks .................................................................................................................................................... 31 Operational differences ............................................................................................................................................... 31 Network addressing ......................................................................................................................................................... 31 DALI network wiring ....................................................................................................................................................... 32 Device compatibility ..................................................................................................................................................... 32 Normal DALI ................................................................................................................................................................. 34 DALI Multi Master ........................................................................................................................................................ 34 Enumeration ................................................................................................................................................................... 35 Emergency lighting ............................................................................................................................................................ 35 Self contained luminaries ............................................................................................................................................. 36 Testing emergency lighting.......................................................................................................................................... 38 Essential supply load shedding.................................................................................................................................... 38 Maintaining circuits by bypassing load controllers ................................................................................................ 40 Error! No text of specified style in document.


3

DMX..................................................................................................................................................................................... 40 End of line resistors ...................................................................................................................................................... 40

Topic 2: Installing load controllers.................................................................................................... 41 Overview............................................................................................................................................................................. 41 Learning outcomes ....................................................................................................................................................... 41 Hardware controls ........................................................................................................................................................... 41 Service LED and switch ............................................................................................................................................... 41 AUX input....................................................................................................................................................................... 42 Top set ............................................................................................................................................................................ 42 Wall mounted devices ..................................................................................................................................................... 42 Select a suitable location ............................................................................................................................................. 42 Fixing the device ............................................................................................................................................................ 44 Allow for cable entry ................................................................................................................................................... 44 Supply & load cable ....................................................................................................................................................... 44 Powering up the dimmers prior to commissioning .............................................................................................. 45 Operating environments ............................................................................................................................................. 45 DIN rail mounted devices ............................................................................................................................................... 45 Instructions ..................................................................................................................................................................... 45 Circuit breakers ............................................................................................................................................................ 47 Multi controllers............................................................................................................................................................ 47 Structured wiring boxes .................................................................................................................................................. 49 Select a suitable location ............................................................................................................................................. 49 Fixing the device ............................................................................................................................................................ 49 Wiring terminations ..................................................................................................................................................... 50 Supply and output connections.................................................................................................................................. 50 Dry contact switch input connections ..................................................................................................................... 51 Network connections .................................................................................................................................................. 51

Topic 3: Installing panels ..................................................................................................................... 53 Overview............................................................................................................................................................................. 53 Learning outcomes ....................................................................................................................................................... 53 Instructions ..................................................................................................................................................................... 53 Connecting data cables ................................................................................................................................................ 53 Factory presets .............................................................................................................................................................. 54 Changing button configurations ..................................................................................................................................... 56 DLP & DL2P ................................................................................................................................................................... 57 DR2P ................................................................................................................................................................................ 57 DPN58 Panel network connections ............................................................................................................................................ 58 Dingus .............................................................................................................................................................................. 58 LSP-PRO .......................................................................................................................................................................... 59 FFC-LSP ........................................................................................................................................................................... 59

Topic 4: Installing motion sensors .................................................................................................... 61 Overview............................................................................................................................................................................. 61 Learning outcomes ....................................................................................................................................................... 61 Installation instructions ................................................................................................................................................ 61 Mounting PIR motion sensors .................................................................................................................................... 62

4



Mounting Ultra sonic motion sensors...................................................................................................................... 62 DUS704C motion coverage ....................................................................................................................................... 63 DUS804C and DUS804C-SM motion coverage .................................................................................................... 63 DUS804C-UP ultra sonic motion coverage ........................................................................................................... 64 Motion detection lens pattern ................................................................................................................................... 64 Optional motion detector lens for DUS704W ..................................................................................................... 65 Selecting sensor installation locations ...................................................................................................................... 66 Sensor mounting for PE (photo electric) ................................................................................................................ 67 Infrared receiver mounting location ......................................................................................................................... 68 Installing DUS704W-MB mounting brackets .......................................................................................................... 68

Topic 5: Installing touch screens ....................................................................................................... 70 Overview............................................................................................................................................................................. 70 Learning outcomes ....................................................................................................................................................... 70 General installation points for touch screens ........................................................................................................ 70 Installing the DTP170 ....................................................................................................................................................... 71 Fixing the device ............................................................................................................................................................ 71 Installing the DTP100 ....................................................................................................................................................... 72 Fixing the Device ........................................................................................................................................................... 73 Power supply .................................................................................................................................................................. 73

Topic 6: Installing integration devices .............................................................................................. 74 Overview............................................................................................................................................................................. 74 Learning outcomes ....................................................................................................................................................... 74 Installing the DDMIDC8 .................................................................................................................................................. 74 Features ........................................................................................................................................................................... 74 Installation notes ........................................................................................................................................................... 75 Electrical diagram .......................................................................................................................................................... 75 Analogue fader ............................................................................................................................................................... 76 Installation steps ............................................................................................................................................................ 76 Installing DDNG485 ......................................................................................................................................................... 76 DPMI940.............................................................................................................................................................................. 77 Using the DPMI940....................................................................................................................................................... 78 Installation steps ............................................................................................................................................................ 78 Electrical diagram .......................................................................................................................................................... 79 Mounting details ............................................................................................................................................................ 79 Connecting to a motion detector ............................................................................................................................. 79 Connecting volt free inputs ........................................................................................................................................ 80 Install DDFCUC024 / DDFCUC10 .............................................................................................................................. 81

Topic 7: Testing and troubleshooting .............................................................................................. 82 Overview ................................................................................................................................................ 82 Learning outcomes ....................................................................................................................................................... 82 Walk through test procedure ........................................................................................................................................ 82 LED tracking ................................................................................................................................................................... 82 Luminaires ....................................................................................................................................................................... 82 Sensors ............................................................................................................................................................................ 82 Touch screens................................................................................................................................................................ 83 Troubleshooting ................................................................................................................................................................ 83 Error! No text of specified style in document.


5

Network Fault finding .................................................................................................................................................. 83 Power Supply faultfinding ............................................................................................................................................ 83 Panel Fault finding.......................................................................................................................................................... 83 End of line resistors ...................................................................................................................................................... 84 Common problems ...................................................................................................................................................... 84 DDMIDC8 Troubleshooting ...................................................................................................................................... 85 Do’s and don’ts of dimming low voltage transformers ............................................................................................ 85 Do’s and don’ts of dimming fluorescent lighting ....................................................................................................... 86

6



About this guide Guide Overview This guide is designed to assist in the configuration of Dynalite control devices. A working knowledge of EnvisionProject and Dynalite commissioning processes is required to effectively use this document. For more information on commissioning processes, consult the Dynalite Programmers Guide. Parameters in the software may require information that must be sourced from third party manufacturer’s device details and specifications. Disclaimer These instructions have been prepared by Philips Dynalite and provide information on Philips Dynalite products for use by registered owners. Some information may become superseded through changes to the law and as a result of evolving technology and industry practices. Any reference to non- Philips Dynalite products or web links does not constitute an endorsement of those products or services Copyright © 2011 Dynalite manufactured by WMGD Pty Ltd (ABN 33 097 246 921). All rights reserved. Not to be reproduced without permission. Dynalite, Dimtek, DLight, DyNet and associated logos are the registered trademarks of WMGD Pty Ltd.

Philips Dynalite 6/691 Gardeners Road Mascot NSW 2020 Australia P: +61 (0)2 8338 9000 F: +61 (0)2 8338 9999 E: dynalite.info@philips.com W: www.philips.com/dynalite

8



Topic 1: Infrastructure Overview In this topic we investigate network architecture of Philips Dynalite networks, cabling requirements and terminations of different cabling types.

Learning outcomes The approach to programming a Philips Dynalite system can be broadly categorized as follows: •

Cabling requirements of a Dynalite network

•

Termination of data cables

•

Topology of small networks

•

Topology of trunk & spur networks

•

Topology of Ethernet networks.

•

Termination of different cabling types.

Cabling Networking requirements Here are some important points to understand about cabling requirements: •

The system communicates over screened, stranded RS485 data cable (such as Cat5) and requires a minimum of three twisted pairs.

•

It is recommended that the data cable is connected between devices in a ‘daisy chain’ arrangement. Start at the first device then loop in then out of devices, with a single cable terminating at the last device.

•

If it is necessary to wire the system in a star configuration the system will still operate normally but diagnosing installation network faults should this be necessary will be more difficult.



9

Figure 1 – Cabling

•

A 5-way pressure pad terminal strip is provided on devices for each data cable termination. Some devices also have an RJ12 connector for temporary connection of portable programming devices.

•

DR2P/E panels are available with 2x RJ12 connectors instead of a pressure pad terminal strip for data connection. These panels use Philips Dynalite flat network cable. Using RJ connectors speeds up the instillation time and helps to eliminate cabling errors. The flat cable supports up to 10 panels on one cable run and its maximum cable run for a single cable is limited to 100m before a network bridge is required.

Note: That any data cable that is connected to an energized device is live. Data cable should not be cut or terminated while live!

CAT 5 cable limits Philips Dynalite Cat5 data cable is specifically designed for high reliability RS485 network wiring. In addition to a twisted pair for RS485 data, conductors are provided to supply DC power to network powered peripherals. Conductors are shielded for maximum data integrity. The data cable is flexible, as all conductors are stranded, which also allows for robust termination into pressure plate style terminals used on most Philips Dynalite equipment. The extra thick outer jacket is mains rated for use in switchboards, and enhances the robustness of the cable. The cable is supplied in 305 meter lengths. Cable limits:

10

•

Maximum Philips Dynalite devices per CAT5 cable: 100.

•

Maximum Cat5 cable length: 1000m.



Figure 2 – CAT5

CAT 5 wiring diagram

Figure 3 – CAT5 Wiring

Recommended DyNet color coding for CAT5 cable COLOR

SIGNAL

Blue Mate Blue

DataData+

Orange Mate Orange

}

Paralleled for +12Volts.

Green Mate Green

}

Paralleled for Ground.

Brown Mate Brown

}

Spare pair if required to repair damaged cable or can be used as a drain for static if unshielded cable used in the installation.



11

Recommended DyNet CAT 5 data cable types MANUFACTURER

PART NUMBER

Philips Dynalite

DyNet STP-Cable

Belden

9503

Garland

MCP3S

Garland

STPL5e

Hartland

HCK603

M & M Cable

B2003CS

M & M Cable

B9503CS

Multicables

AWM E120236 2092 20

RS Components

368-687

Belden wiring diagram

Figure 4 – Belden Wiring

12



Recommended DyNet color coding for Belden cable COLOR

SIGNAL

Black

Ground

Blue

Data+

White

Data-

Red

+12Volts/+24 Volts

The recommended cable types for Belden are: •

#1502R

•

#1502P

S-Flat 6 cable limits Flat data cable is specifically designed for high reliability localized network wiring as found in hotel rooms and residential applications. In addition to a conductor pair for data, conductors are provided to supply DC power to network powered peripherals. Conductors have an overall shield for maximum data integrity. The data cable is flexible, as all conductors are stranded. It is designed for rapid crimp termination into RJ12 plugs for use with Philips Dynalite products with supporting RJ12 sockets. The cable is supplied in 200 meter rolls, or in pre-terminated leads of 3, 5 and 10 meter lengths. Cable limits: •

Maximum Philips Dynalite devices per special flat cable: 10.

•

Maximum special flat cable length: 100m. Silver White Red Yellow Green Brown Figure 5– Flat cable



13

Recommended DyNet color coding for S-Flat 6 cable COLOR

SIGNAL

Silver

Not connected

White

Ground

Red

Data +

Green

Data -

Yellow

+12 Volts

Brown

Not connected

Pin out conversion for RJ45 cable testers RJ12 PINS

RJ45

CABLE COLOR

-

1

-

1

2

Silver drain

2

3

White

3

4

Red

4

5

Green

5

6

Yellow

6

7

Orange

-

8

-

RJ12 socket connections The diagram below details RJ12 socket connections:

Figure 6 - RJ12 Socket Connection

14



Termination CAT5 Instructions Follow instructions below for CAT5 cable termination on a Philips Dynalite network. 1. Using side-cutters cut a slit at the end of the cable. Use care to ensure only the out plastic sheath is cut, avoiding the inner cores and shielding sheath.

Figure 7

2. Locate the draw string between the outer sheath and the foil shield wrapper and using pliers pull downwards to cut a 90mm slit in the outer sheath shown in figure 8.

Figure 8 Topic 1: Infrastructure


15

Figure 9

3. Using side-cutters carefully trim away the outer plastic sheath, again ensuring not to cut the inner cores.

Figure 10

16



4. Locate the shield drain wire and separate from the shield’s foil sheath. Once separated carefully trim away the foil shield and plastic wrap.

Figure 11

5. Bend the Brown/Brown-White pairs back towards the outer sheath to be kept as spares.

Figure 12



17

6. Using a cable-tie secure the two cables together.

Figure 13

7. Trim away the excess from the cable tie.

8. Twist both of the shield wires together.

Figure 14

18



9. On both cables untwist the Blue/Blue-White pairs.

Figure 15

10. Twist together the Blue wire from each pair. 11. Twist together the Blue/White wire from each pair. 12. Twist together the Green-Green/White wire from each pair. 13. Twist together the Orange-Orange/White wire from each pair.

Figure 16



19

14. Strip 10mm of sheath from each of the wires and twist together.

Figure 17

15. Fold this back on itself to improve contact with the screw terminal, this should then be 5mm in length. 16. Over the shield wire slide a piece of sheathing. This is to help prevent the shield being inadvertently shorted.

Figure 18

20



Terminate each cable as shown. •

Shield - Shield

•

Ground - Green/Green-White

•

Data + - Blue

•

Data - - Blue-White

•

+12V – Orange/Orange-White.

Figure 19

17. Ensure the conductors are fully inserted into the terminals with no loose strands escaping.

Figure 20

18. The process in complete. Topic 1: Infrastructure


21

Flat cable instructions Correctly stripped cable

Incorrectly stripped cable – shield still present

Figure 21

Figure 22

Figure 23

DyNet voltages Below are voltage values for proper operation of a DyNet network:

22

•

Max – Min voltages: EU/AUS 10-18V, NA 18-26

•

Max ripple: 1Vrms @100/200Hz

•

Max voltage range for Data+ and Data –: -6.5V - +6.5V (Data+ must be greater)

•

Min voltage difference between Data + and Data-: 500mV recommended, 200mV is absolute minimum



•

Max voltage range for power connections: +9V- +16V

Network architecture The concept of a centralized controller and the complicated task of ‘binding’ individual slave devices to the central controller in a DyNet network is completely eliminated. Each individual device will inherently know what they are and simply listen to and broadcast onto the network. This means that in most cases, particular devices on the network do not know or care about other devices. They simply respond to network messages, to which they are inherently sensitive, and broadcast their own class of messages with no particular destination in mind. A key principle of the DyNet network is that all of the functions associated with a particular device are located within that device. For example, all scene preset information is stored within the actual controllers. This means that if any device should fail, only the functions associated with that device are lost, other devices on the network are not affected. From a maintenance point of view, this concept of distributed control (self-contained) units both speeds up fault-finding, and allows a high level of fault tolerance in large systems. This ‘Broadcast Network’ operating principle provides the necessary flexibility to ensure that the system can be easily (and at low cost) altered or added to after installation. It is possible to add extra equipment at any time without the need to re-configure or rewire the entire system.

The DyNet Network The DyNet network is the communications layer that links the various Dynalite products together and enables them to interact with each other. For the purpose of discussion it can be divided into two sections, the Physical Layer and the network protocol.

The Physical Layer Dynalite products utilize RS485 which is an industry standard method of data transmission as detailed in the TIA/EIA-485-A specification, with some variations. The TIA/EIA-485-A specification defines a UL (Unit Load), which declares that an RS-485 driver must be able to drive 32 ULs. This means that an RS-485 network supports 32 nodes, when each node bears a unit load on the line. Dynalite products use 1/8 UL drivers, which allow up to 256 devices on a network segment. Another important variation from the TIA/EIA-485-A specification is the addition of an extra conductor that carries a DC supply, which is generated by an integral power supply contained within all mains powered devices and is used to energize those devices that do not connect to mains power, such as motion detectors and wall switches.



23

Trunk & spur network Implementing trunk & spur topology This style of topology is used in large installations, where there are one or more data trunk cables that may interconnect network bridges located at different floors or distribution boards. The second port on the network bridge is then connected to a spur that feeds the dimmers and control panels in that locale. The recommended method of connection is to connect the Spur to the Port 1, and the trunk to the Port 2. Some reasons for implementing Trunk/Spur topology include: Optical isolation– A fault on a Spur will be localized to that Spur only, the rest of the system will be unaffected. Quantity of network devices – A finite number of devices can be connected to a single RS485 data cable. The recommended maximum number of devices is 100. The use of network bridge gives a maximum of 100 devices per spur, with 128 spurs per trunk gives a total of 12800 devices per trunk. Adding network isolators on spurs and running multiple trunks removes any realistic limitation from a single Philips Dynalite network.

24



Trunk & spur network

Figure 24 Topic 1: Infrastructure


25

DLight III trunk &spur network

Figure 25

26



Ethernet networks It is possible to use an Ethernet network to work as a trunk with DyNet spurs. The figure below shows an Ethernet trunk connected to DyNet spurs with the DNG100BT Ethernet interface.

Figure 26



27

Multi trunk networks Multi trunk networks are used in large multi story projects, the purpose of a multi trunk network is to increase the speed of communication.

Figure 27

28



Network cable current limits and voltage drop Because a number of devices are powered over the network the quantity of consuming devices such as panels and sensors needs to be considered. Typically most panels and sensors will run between 10-15V DC @ 25mA. To overcome voltage drop or large numbers of consuming devices a secondary power supply (DDNP1501) may be added to boost the overall network voltage. The DDNP1501 will deliver 15V at 1.5A. Generally most Philips Dynalite load controllers generate around 100mA to the DyNet network and will drive 4 or 5 consuming devices without the need for a secondary power supply. It is important to note that all Cat5 cable has a maximum current capacity of 2A. It is important that the network is designed not to exceed this rating. Devices such as touch screens draw as much as 400-1000mA from the DC supply. In this case it is recommended that the touch screen be feed directly from a DDNP1501. Furthermore we would recommend that the connections at this device be limited to only GND, D+ and D- to avoid exceeding the 2A cable limit. See below figure.

Figure 28 – Data only Connection


Figure 29 – Power only connection


29

Power Supply

Leading edge Trailing edge 0-10V

Power only connection

Touch screen

DyNet network

Data only connection

Standard connection

Figure 30

HF Ballast installation Installation instructions 1. Calculate loads to ensure any channels are not overloaded, then connect loads to the output channels. The maximum loading of this device is as follows: 2. *DALI broadcast mode: 80 ballasts per channel, do not exceed 500 ballasts in total 3. *1-10V mode: 100mA, 50mA source 4. *DSI Mode: 100 ballasts per channel, do not exceed 1200 ballasts 5. Remember that most 1-10V cabling scenarios are polarity conscious. DALI and DSI cables are not polarity conscious. 6. Connect a single phase 0.5A feed to the supply terminals. This device must be earthed. 7. Connect data cables to the device as per diagram in instruction manual for the controller. 30



8. If the Auxiliary input is to be used, connect a dry contact device in between the AUX and GND terminals. Keep cable runs between the controller and the dry contacts under 2 meters. The function of the Auxiliary input will need to be programmed at the time of commissioning. Note: The correct operation of DALI broadcast mode relies on the ballasts being set to their factory defaults. If problems are encountered, press the service switch 3 times, this will reset all ballasts connected and energized to their default settings.

DyNet 1 & 2 networks Operational differences The maximum number of available Areas in a DyNet 1 network is 255. DyNet 1 is an open protocol. The maximum number of available Areas in a DyNet 2 network is 65536. DyNet 2 is a closed protocol.

Network addressing A DyNet network has two different addressing modes: Physical addressing is used primarily during the testing and commissioning stage to configure DyNet Devices. It is also used for physical, location specific parameters such as circuit breaker trip signaling. A Device Type, Box Number and Physical channel number are used to identify each individual lighting circuit. Logical addressing is used in the day-to-day operation of the lighting system. Lighting circuits and control panels are configured to Areas; independent of the physical device they are connected to. An Area Number and Logical channel number are used to identify single or groups of Physical Channels. Areas are used to group related lighting points by the area/room they are in. Consider the example of a load controller that supplies lighting circuits to 2 rooms, with a control panel in each room. The controllers lighting circuits and the control panel in Room 1 could be configured as Area 2, and the controllers lighting circuits and the control panel in Room 2 could be configured as Area 3. The end result would be that the control panel configured to Area 2 would only control circuits designated Area 2. The control panel configured to Area 3 would only control circuits designated Area 3. This allows the two rooms to operate independently of one another.



31

Logical 1

Logical 2

Logical 1

Office 1 Area 2

Logical 2

Office 2 CP 1

Area 3

CP 2

Figure 31

DALI network wiring Device compatibility Philips Dynalite DALI compatible load controller range is listed below, : •

•

•

DMBC110 - HF Ballast Fixture Coupler −

1 x output selectable to: DALI Broadcast, 1-10V, DSI

−

DALI Ballasts and transformers: 5, 0-10V: 10mA source or 20mA sink DSI Ballasts and transformers: 15.

DDBC100 - DALI- DALI HF Ballast Controller −

1 x DALI control output, supporting a full DALI universe of 64 channels, including backward channel

−

Diagnostics include; Lamp failure reporting, Ballast failure reporting, Ballast run time tracking for each ballast, Device Online/Offline status.


•

32

3 DALI control outputs, each supporting a full DALI universe of 64 channels (192 total), including backward channel.


3 DALI control outputs, each supporting a full DALI universe of 64 channels (192 total), including backward channel

−

3 x 20A feed through switched circuits for DALI ballast mains supply.



•

DDMC802 - Multipurpose Controller −

•

•

DDBC1200 - HF Ballast Controller −

12 control outputs, selectable to DALI (Broadcast mode only), 0-10V or DSI

−

Output capacity - DALI mode: 80 DALI ballasts per channel, 500 total, 0-10V mode: 100mA sink, 50mA source per channel, DSI: 100 DSI ballasts per channel, 1200 total.

DBC905 - 1-10V & DSI HF Ballast Controller −

•

•

DDBM100 1 channel ballast module, suitable for controlling DALI (Broadcast mode only), DSI & 1-10V ballasts and transformers (a relay module must be paired with a HF ballast module when controlling 1-10V ballasts).

9 x HF ballast control outputs, each selectable to 1-10V, DSI or DALI.

DBC1220GL - DALI, DSI & 1-10V & HF Ballast Controller −

12 x HF ballast control outputs, each selectable to 1-10V, DALI (Broadcast mode) or DSI

−

Output capacity - DALI mode: 64 DALI ballasts per channel, up to a maximum of 400.

DBC1210 - DALI, DSI & 1-10V HF Ballast Controller. −

12 x HF ballast control outputs, each selectable to 1-10V, DALI (Broadcast mode) or DSI.

−

Output capacity - DALI mode: 64 DALI ballasts per channel, up to a maximum of 400, DSI mode: 100 ballasts per channel, up to a maximum of 1,200, 1-10V mode: 50mA sink/source per channel.



33

Normal DALI

Figure 32

DALI Multi Master

Figure 33

34



Enumeration DALI ballast enumeration can cause some trouble shooting confusion, below is a list of points to keep in mind when addressing DALI issues: •

Hit the service switch 4 times to start the test sequence. (wait for the time out or reset device)

•

Check that the number of ballasts does not exceed 64 per universe

•

Check voltage on circuits, it should be 15v

•

Split the universe and then enumerate.- this will narrow down the search area for the defective ballast.

•

Check for miss wired ballasts – miss wired ballasts will cause a variety of dimming issues

•

Check that all ballasts have been earthed correctly

•

Check ballasts are wired correctly – make sure that the long and short wires are connected correctly, to check remove the lamp and short the 2 wires together, this should cause the universe to alternate between 0% and 100%.

Figure 34

•

Cable length to long or too skinny

•

We recommend the Tridonic – config tool v1.5

•

Cross wired universes.

Emergency lighting There is a common requirement for emergency lighting to be used alongside general lighting connected to a control system. There are a few ways of achieving this, the most appropriate method is dependent on the type of emergency lighting fixture and control equipment used. Following is a description of several different techniques and their respective deployment methods. Sometimes it will be necessary to combine two or more techniques to achieve the desired outcome.



35

Self contained luminaries There are three common types of Self Contained Luminaires (also known as Single Point Luminaires): Maintained luminaires - This is an exit or emergency luminaire, where the lamps used for emergency lighting also operate under normal supply. The lamps used in these luminaires are often fluorescent, with a dimmable ballast and can be controlled in exactly the same manner as a normal dimmable fluorescent luminaire. Maintained Luminaires have two line inputs. One is connected to the Normal lighting output of the load controller. The Maintained input is connected to the load side of the load controller’s circuit breaker, which supplies power to charge the internal battery and to use as a signal to turn the lamp on in the event of a power failure. In this example the Maintained Luminaire is also used for Normal Lighting, it’s ballast is dimmable so ballast control lines are shown. Commonly used control protocols are DALI, DSI and 1-10V.

Figure 35

Non-maintained luminaires - This is an exit or emergency luminaire, where the lamps used for emergency lighting only operate when the normal supply fails. The lamps used in these luminaires are often incandescent such as the small “Spitfire” halogen lamp and the larger, sealed beam flood lamp units. Non-Maintained Luminaires are connected to the load side of the load controller’s circuit breaker, which supplies power to charge the internal battery and to use as a signal to turn the lamp on in the event of a power failure. This connection method allows full control of the normal lighting while providing for emergency lighting in the event of a circuit breaker trip or power supply failure.

36



Figure 36

Sustained luminaires - This is an exit or emergency luminaire with two or more lamps where at least one lamp operates in non-maintained mode and is only illuminated when normal supply fails. The other lamp operates on the normal supply only. This is identical in functionality to having a Non-Maintained Luminaire and a Normal Luminaire both in the same housing. charge the internal battery and to use as a signal to turn the lamp on in the event of a power failure. In this example the normal half of the Sustained Luminaire is used for Normal Lighting, it’s ballast is dimmable so two ballast control lines are shown, common protocols are DALI, DSI and 1-10V.

Sustained Luminaires have two line inputs. One is connected to the Normal lighting output of the load controller. The Sustained input is connected to the load side of the load controller’s circuit breaker, which supplies power to charge the internal battery and to use as a signal to turn the lamp on in the event of a power failure. In this example the normal half of the Sustained Luminaire is used for Normal Lighting, it’s ballast is dimmable so two ballast control lines are shown, common protocols are DALI, DSI and 1-10V.

Figure 37



37

Testing emergency lighting Most local lighting codes require the testing of emergency lighting systems at defined intervals. Common problems include failed lamps and aged batteries that no longer meet the luminaire’s rated duration. To assist in the testing process, some models of Dynalite load controllers are optionally available with Emergency Lighting Outputs (ELx). This controlled output is fed via an NC relay and provides power to the maintained input of Emergency Luminaires. The ELx outputs from multiple load controllers can be remotely disconnected for a defined period of time, for example a test button would switch off all ELx outputs for a particular office floor, maintenance staff would then perform a ‘walk through’ to identify failed components. This process can be automated with the addition of extra hardware in the luminaire.

Figure 38

Essential supply load shedding Some sites are equipped with a standby generator, which will automatically start upon failure of normal supply and, after operating parameters are reached, will switch part or all of the site from the normal supply circuit to the generator’s output, resulting in the site being re-energised some 10 to 20 seconds after normal supply failure. Quite often the standby generator is coupled with a UPS (Uninterruptible Power Supply), which ensures there is no power dropout during the changeover period. In theory, the lighting system should operate as it would on normal supply, but in practice it is often desirable to modify its behavior. Two common reasons for doing this are: The Standby Generator does not have the power capacity required to operate the site normally. In this case it is desirable to place the lighting system into a load shedding mode.

38



The site should not be occupied while normal power is not available. In this case it is desirable to place the lighting system into an egress mode. To change the operating mode, the lighting system must be made aware that the generator is online. This is typically carried out via a relay that actuates when the generator is online, (or sometimes via a relay that actuates when the normal supply fails) providing a dry contact signal to an input unit on the lighting control network, such as a DDMIDC8 Multifunction Input Interface.

1 Phase 40 AMP

Figure 39

In egress mode The DDMIDC8 locks out all control devices such as wall mounted Control panels, touch screens, motion detectors etc, and selects a global egress preset, which is pre-defined to illuminate egress paths and reduce lighting in workspaces to assist in alerting occupants that something is amiss. When normal power is restored the DDMIDC8 restores normal control functionality. Load shed mode The DDMIDC8 instructs all load controllers to use a different set of presets than the normal ones. Consider the example of a room with two channels of lighting and a control panel that recalls four presets: During normal operation, presets 1-4 are recalled from the control panel. In load shed mode the DDMIDC8 uses a part of the DyNet feature set called ‘Preset Offset’, which instructs the load controllers to recall presets 5-8. This function can target a single or group of rooms, or more commonly, the whole site. If it is desirable that no lighting is on at all in particular rooms in load shed mode, then all load shed presets are set to 0%. This method has the advantage of minimal impact on the site, as lighting levels in particular rooms are not disturbed if they are already off or at low levels.



39

Maintaining circuits by bypassing load controllers When there are only a small number of circuits to be maintained when a site changes over to a standby generator or UPS, a simple solution is to bypass the lighting control system with contactors that connect the circuits to be maintained directly to the essential supply.

Figure 40

In this scenario the non-essential supply is used to hold a contactor closed, connecting the lamp to the load controller. When the non-essential supply fails the load controller will be deenergized as will the contactor, which will connect the lamp to the essential supply.

DMX End of line resistors •

At 9600 Baud the distortion of the original signal is usually within limits and so EOL resistors are not recommended on a standard DyNet system.

•

Baud rates greater than 9600 Baud must be terminated using a 120Ω resistor across D+ and D-.

•

Usually fitted into network connector strip for 1st and last devices.

•

For DMX integration – network must be daisy chained with end of line resistors.

D+ D--

120R

120R

D+ D-Figure 41

40



Topic 2: Installing load controllers Overview •

This document is a guide to installing Philips Dynalite components to a state where it is really to be commissioned.

•

Every Dynalite product is delivered with a comprehensive instruction manual. It is important that you read the installation instructions for each product before using this guide.

Learning outcomes By the end of this topic you’ll be able to detail the installation steps for the following devices: •

Wall mounted devices

•

DIN rail mounted devices

•

Mounting structured wiring boxes

•

Mounting panels

•

Mounting sensors

•

Mounting touch screens

•

End of line resistors.

Hardware controls Service LED and switch The Service LED has 3 signaling modes, which are useful for troubleshooting: •

Blinking slowly (1Hz) = Normal Operation

•

Blinking fast (0.25Hz) = Network Activity Detected

•

On = Fault.

Topic 2: Installing load controllers


41

The Service Switch, when pressed, causes a “sign-on” message to be transmitted onto the network. If the transmission is successful, the Service LED will indicate “network activity detected”. The Sign-on message contains information about the device, such as: box number, device type and embedded software version. This information is captured by DLight configuration software to speed up commissioning of large systems. The Service Switch three states are: •

1 push = Transmit Network ID

•

3 pushes = All Channels 100%

•

Push & hold for 4 sec = Reboot.

AUX input This is a dry contact interface that is active low. The dry contact is connected between the AUX and GND terminals on the DyNet connector strip. The function of the AUX input is programmable. Ensure that the cable length between the dry contact and terminal strip is no longer than 2 meters.

Top set This adjusts the maximum output that all other control sources can select, i.e. if the Top Set is fully clockwise, 100% selected by a control source will give 100% output. If it is fully anticlockwise, 100% selected by a control source will give 50% output. This control is useful for extending lamp life and can be operated without any form of network control, effectively turning the device into a stand-alone power conditioner and lamp protector.

Wall mounted devices Select a suitable location Some of Philips Dynalite products are available in the wall mounted form factor, these include: •

Load controllers

•

Network Bridges.

Wall mounted devices are designed for indoor use only. If installing in an external location, the device must be housed in a suitable well-ventilated enclosure. Choose a dry location that will be accessible after the installation is complete. To ensure the cooling system functions correctly, the load controller should only be mounted vertically, the right way up.

42



The load controller will generate heat when operating, approximately 2 Watts per Amp of load, and requires an air gap of 200mm on each side and at the top and bottom of the device. This air gap is also required to ensure serviceability of the load controller without complete removal from the mounting surface. This device may emit some mechanical noise. Take this into account when deciding the mounting location.

Figure 42

Figure 43

Figure 44



43

Fixing the device The load controller has integral mounting brackets attached to the enclosure. The brackets are designed to accommodate 4 fixing screws up to 8mm diameter. The load controller can be fixed to the wall without opening the cabinet or removing covers. Make sure no dust or other debris enters the device during installation. Do not leave the front cover off for any length of time. Excessive dust and dirt can degrade the cooling of internal components.

Allow for cable entry Supply and load cables enter the enclosure at the top. If these cables are fed from below the mounting position, they should be routed around the enclosure to enter at the top. An alternative method is to stand the enclosure off from the mounting surface by mounting it on a cable tray or a Unistrut style product. The cables can then be routed between the enclosure and the mounting surface, and enter the enclosure via the cut out provided on the mounting face. The control cables enter at the bottom of the enclosure. Control cables should never be run in the mains voltage sections of the enclosure.

Supply & load cable Supply Cables -The supply input terminals are located toward the top of the enclosure and consist of Earth, Neutral, and Phase. The supply cables should have enough capacity to allow the device to be loaded to its maximum capacity. Load Cables - Load cables can be terminated on the 4 x 3 way load terminal strips (one for each channel), a Neutral link and an Earth link located at the centre of the enclosure. It is important that an individual output circuit is not overloaded. Calculate the intended load, and ensure that it is below the maximum capacity of an individual channel. To ensure compliance with interference standards, the load neutral cables must be individually connected to the neutral link terminals inside the cabinet. Never use a common neutral at a remote location. Emergency Lighting Connections - Connect the emergency lighting circuit active to the load side on the circuit breaker for the relevant channel, as indicated by the labels next to the circuit breakers. Do not remove any cables that may already be terminated at this location. Energizing the Device - If it is necessary to energies load circuits before any control cables are connected, it is acceptable to replace the cover and energies the device immediately, as the default factory programming is to have all channels set to 100% output. This device should be deenergized before terminating the control and data cables.

44



Powering up the dimmers prior to commissioning All devices are pre-programmed with a default configuration before leaving the factory. When all the devices are installed and networked together, every button panel will control all the dimmers. The Dynalite engineer requires the system to be installed to this level to commission the project successfully. All Dynalite load controllers are set to provide full output to the load as the default, irrespective of having the network connected. When the network is connected, every button panel will operate every circuit of every device.

Operating environments This device is designed for indoor use only. If installing in an external location, the DLE1205 must be housed in a suitable well ventilated enclosure. Choose a dry location that will be accessible after the installation is complete. In addition the load controller must not be in a location that exceed the following limits for temperature and humidity: 0º to 40ºC ambient temperature 0% to 95% RH non condensing.

DIN rail mounted devices Instructions A number of devices are available in the DIN rail form factor, these include: •

Load controllers

•

Time clocks

•

Power supplies

•

Network gateways

•

Dry contact interface devices.



45

Follow the points below to ensure correct installation of DIN rail mounted devices: •

Mount the device on a DIN rail inside an approved enclosure.

•

Calculate loads to ensure any channels are not overloaded, then connect loads to the output channels.

•

This device must be earthed

•

Connect data cables to the device as per diagrams in the previous topic.

•

If the Auxiliary input is to be used, connect a dry contact device in between the AUX and GND terminals. Keep cable runs between the device and the dry contacts under two meters. The function of the Auxiliary input will need to be programmed at the time of commissioning.

•

Every Dynalite product is delivered with a comprehensive instruction manual. It is important that you read the installation instructions for each product before installation.

Figure 45

46



Figure 46

Circuit breakers Required by each device, consult the product data sheet or instruction manual for details.

Multi controllers When installing Multi Controllers there are some additional considerations to take into account regarding the controller modules. Verify that the Output Cards supplied are suitable for your intended loads. Pay attention to any Output Card specific documentation that may be packed with Output Cards. When dimming electronic transformers, ensure that the intended transformer is included in Dynalite’s Compatible Electronic Transformer List, the latest revision is available at dynalite-online.com 1. Snap the cover off the base unit. Plug each Output Card into the slots provided on the main circuit board. Replace the base unit’s cover. If using different types of Output Cards, remember which type is associated with each set of output terminals. 2. Mount the device on a DIN rail inside an approved enclosure. 3. Calculate loads to ensure any channels are not overloaded, then connect loads to the output terminals. The maximum loading of this device is 16A. A de-rating factor may need to be applied if installed in a smaller sealed switchboard when using Leading or Trailing edge dimmers, contact your dealer for details.



47

The output card ratings are: •

DDBM100 Ballast Controller – Digital mode : 5 x Ballasts

•

DDBM100 Ballast Controller – DSI mode : 15 x DSI Ballasts

•

DDBM100 Ballast Controller – 1-10V mode : 10mA source, 20mA sink

•

DDCM102 Curtain Controller : 2 Amps

•

DDFM102 Fan Controller : 1 x Fan, max 400VA

•

DDLM102 Leading Edge Dimmer : 2 Amps

•

DDLM104 : Leading Edge Dimmer : 4 Amps

•

DDRM104 Relay Controller : 4 Amps

•

DDTM102 Trailing Edge Dimmer : 2 Amps

WARNING : Ballast controller output is referenced to mains neutral and is live. Only mains rated cables and control ports should be connected.

Ensure that lamp holders are marked with the maximum permissible lamp size that will not overload a channel. This is to protect the end user from inadvertently overloading a channel by replacing lamps with higher wattage types. 1. Every time the front cover is removed, ensure that all modules are correctly seated and locked into sockets before the cover is replaced. 2. Ensure that lamp holders are marked with the maximum permissible lamp size that will not overload a channel. This is to protect the end user from inadvertently overloading a channel by replacing lamps with higher wattage types. 3. Connect a single phase 16A feed to the supply terminals, via a 16A circuit breaker or HRC fuse. This device must be earthed. 4. Connect data cables to the device as per diagrams below. 5. The Auxiliary input is connected via a dry contact device in between the AUX and GND terminals. Keep cable runs between the device and the dry contacts under two metres. The function of the Auxiliary input will need to be programmed at the time of commissioning.

48



Structured wiring boxes Select a suitable location This device is designed for indoor use only. If installing in an external location, the DBC905 must be housed in a suitable enclosure. Choose a dry location that will be accessible after the installation is complete. To prevent dust or particle penetration the controller should be mounted so that connector apertures do not face directly upwards. Recommended mounting methods include surface wall, slab, cable tray or “drop rod” suspension.

Fixing the device The controller has two keyhole slots located at each end of the housing, which can accommodate fixing screws up to 6mm diameter. The preferred method of mounting is shown below using “drop rods” with appropriate fastening clips.

Figure 47



49

Wiring terminations Removable connectors are utilized for all wiring terminations to simplify maintenance, installation and replacement. Note that controllers are supplied without connectors. Please order connectors separately as required.

Figure 48

Supply and output connections The DBC905 is available in two configurations supporting popular structured wiring brands; CMS Electracom / Modular Wiring tag series and Wieland GST18 series. Units are designated by item code as DBC905C (CMS) OR DBC905W (Wieland). Both cable vendors offer a range of wiring solutions and accessories for both the upstream supply and downstream load wiring. The upstream wiring solutions combine both the mains supply and floor network circuits into one wiring assembly, which can dramatically reduce installation time. Please refer to respective vendor for guidelines on connector and cable assembly selection.

DBC905W Output Connector Pole Assignments

Figure 49

DBC905W pole mains input socket

Figure 50

DBC905C Output Connector Pole Assignments

Figure 51 50



DBC905C pole mains input socket

Figure 52

Dry contact switch input connections The DBC905 incorporates 4 x voltage free single pole double throw (SPDT) switch inputs, momentary or latch action with four x 3 pole removable terminal sockets for connection of two way on and off retroactive switches.

Figure 53

Network connections Serial ports are used to interconnect other dimmers, smart control panels, sensors and AV controllers. The DBC905 circuit design incorporates multiple layers of isolation to deliver robust fault tolerance and uncompromising safety. It should be noted that most structured wiring solutions for upstream supply circuitry which include both network and power (i.e. 5 pole systems) only provide functional isolation between the data and mains circuits. Where such wiring systems are used, the floor network must be considered at mains potential not SELV and all floor network wiring should include the appropriate provision for prevention of access to live parts. The main floor network port on the DBC905 is isolated for this reason. The isolation will tolerate a fault which raises the floor network to mains potential. Note that this does not include mains potential applied across D+ and D- which would of course result in destruction of circuit components. Isolation is also separately provided to the local DyNet ports and switch inputs. This ensures that all switch inputs and local network circuits are SELV and prevents propagation of faults from these circuits across the floor network. Where an upstream structured wiring solution is used, care should be made when terminating network spur wiring at floor bridges (area controllers), to again prevent access to parts and wiring considered potentially live. In this case only DBC905 controllers should be connected to the floor network as they incorporate the isolated port. Under no circumstances should a



51

standard user interface be connected directly to the floor network as this may permit user access to potentially live parts. All user interfaces such as sensors and panels should be connected to the local network ports on the DBC905 which provide SELV isolation from mains and the floor network. Where it is necessary to connect user interfaces to a floor network of this type, a bridge should be always used to provide effective isolation.

52



Topic 3: Installing panels Overview This topic covers the requirements and step for installing the Philips Dynalite range of panels. Instructions for DLP, DPN and DR2P are covered.

Learning outcomes By the end of this topic you’ll be able to: •

Install DR2P series user interface panels

•

Install DLP user interface panels

•

Install DPN user interface panels.

Instructions Follow the points below to ensure correct installation: •

Use the mounting screws provided

•

To comply with local electrical standards, some products may be required to be installed into a metal wall box (not supplied).

Connecting data cables •

Follow the points below when connecting data cables to ensure correct installation:

•

Use screened, stranded RS485 data cable with three twisted pairs.

•

Connect data cable to devices in a ‘daisy chain’ whenever possible. Start at the first device, then loop in then out of devices, with a single cable terminating at the last device.

•

Devices may be wired in any order.

•

Physical constraints may dictate that data cable spurs are necessary. In these cases, Network Bridges may be needed.

•

The Data Cable should be segregated from any Mains Cables by a minimum of 300mm. If the Data Cable has to cross over any Mains Cables, it should do so at a 90° angle.

•

A data cable that is connected to an energized dimmer is live. Do not cut or terminate live data cables.

•

Panels can be mounted vertically or horizontally if desired.

Topic 3: Installing panels


53

Factory presets Default preset levels are factory preprogrammed into give basic level of functionality. These can be customized to specifically suit each room or area.

Figure 54

Figure 55

The default preset levels are listed below: PRESET

LIGHT LEVEL

P1

100%

P2

70%

P3

40%

P4

0%

P5

80%

P6

60%

P7

50%

P8

20%

Note: Hold down a button for 5 seconds to sign on a panel to a network.

54



Antumbra panel details Front of device

Back of device

Button switch Network LED Light level sensor

plug

Rim finish

Button guides

Tempreature sensor

Button clip

Network LED

Locating pin guide

Pin header

Communications module Terminal connection DyNet connection plug

Pin connectors Function DIP switches

Location

socket

Network LED Labeling space

Network sign on

plug


Connection header


55

Installation steps

56

The mounting plate needs to be installed with the locating tabs into the wall.

The network cables and connector plug pulls though the mounting bracket.

The plate’s orientation can be either way. Using the long mounting screws provided fix the mounting bracket to the wall. Installers must use the screws provided as different screws could damage the panel once fully installed. Ensure that the mounting plate is level and make adjustments if required.

Once the mounting bracket is mounted plug the five-way network socket into the mounted Communications module.



The whole panel assembly can be pushed into the mounting bracket. Locate and fix the application base to the mounting bracket using the two smaller screws through the mounting holes. Recheck the level of the panel and adjust if required

Changing button configurations DLP & DL2P Buttons, bezels and covers snap-on, remove the fascia to access buttons without the need for any tools or extra wiring.

Figure 56

Figure 57

DR2P DR2P panel buttons are changed individually, see figure 47 below:



57

Figure 58

DPN Buttons for DPN panels can be replaced without the need for any tools or extra wiring. By pinching the button cap on the sides and pulling gently the cap can be removed. The fascia of the DPN panel doesn’t need to be removed for button maintenance.

Figure 59

Panel network connections Dingus You can connect to the back of a panel using a Dingus supplied with the DTK622 PC node.

Figure 60

In addition to the dingus, the LSP-PRO and FFC-LSP can be used to connect to the DyNet network via DL2P and DR2P panels.

58



LSP-PRO Remove the panel’s fascia to access the connector shown in figure 61 below:

Figure 61

Figure 62

FFC-LSP A third type of connector can be used to connect to the DyNet network via a DR2P panel Remove the panel’s fascia to access the connector shown in figure 48 below:

Figure 63


Figure 64


59

60



Topic 4: Installing motion sensors Overview This topic covers the requirements and step for installing the Philips Dynalite range of sensors. Instructions for DUS704C, DUS704W and DUS804C are covered.


Install motion sensors using PIR motion control

•

Install motion sensors using ultra sonic motion control

•

Install motion sensors for light control

•

Install sensors for IR control.

Installation instructions Follow the points below to ensure correct installation: •

WARNING * Do not touch the Pyro Sensor with your fingers. For indoor use only.

•

Select an appropriate indoor mounting location, as detailed in the location guidelines on the following pages. Note that this product has three functions, and the optimum mounting location for each individual function may conflict with each other, and may require the use of multiple sensors.

•

Remove the cover from the base unit by turning the cover in an anti clockwise direction.

•

Screw the base unit to the ceiling, passing the data cable through the cable entry hole.

•

Terminate the data cable as shown previously.

•

Use silicon sealant to seal any cable entry and screw holes to prevent air draughts, dust and insects from entering the enclosure.

•

Replace the cover onto the base unit by turning the cover in a clockwise direction.

Topic 4: Installing motion sensors


61

Mounting PIR motion sensors Follow the points below to ensure correct installation for motion detection: •

Fix the sensor to a firm section of ceiling

•

Position the sensor so it is between 2.1 and 4.0 meters from the floor. Optimum height for the sensor is 2.4 meters

•

Position the sensor so it is at least 1 meter away from electrical lighting such as neon and fluorescent lights

•

Position the sensor as to avoid exposing it to direct sunlight and heating/cooling sources

•

Keep data cables away from electrical wiring

•

Position the sensor where pedestrian traffic is more likely to walk across the detection “fingers” rather than parallel with them (see Lens pattern diagram).

Note: That the coverage area for our sensors differ from model to model (see Motion Detector Coverage diagram on the following pages).

Mounting Ultra sonic motion sensors

62

•

Sensor must be mounted in a dry location on a rigid, vibration free surface. Ideal location for PIR should have a clear view of all workspaces in coverage area. The ultrasonic sensor’s field of view is less directional.

•

Avoid placing sensor where it may face doorways etc which could cause false triggering.

•

Sensor should be located at a distance of at least 7ft from horizontal or vertical air ducts. Adjacent sensors with ultrasonic detector enabled should be installed with a minimum of 60ft spacing between. Sensor should be placed such that the PE cell’s field of view is unobstructed, and does not have an artificial light source or natural light directly incident on it.

•

For flush mount drill a 2.5 inch hole in ceiling, noting the ceiling void should be at least 2 inches deep. If surface mounting option is used, use provided mud ring mounting adaptor. For this option removal of the spring clips from the sensor’s rear housing is required.

•

Wire the sensor following the recommendations. See data cable permanent connections.

•

Insert the sensor into the ceiling using spring clips or attach it to the mud ring mounting adaptor provided, and rotate to secure.

•

Rotate the sensor in the direction of desired Ultrasonic coverage. If required pull-down the PIR masking bezel to stop the PIR sensing in unwanted areas (e.g. movement past doorways).

•

Refer to separate installation guideline document for detailed install information. Installers Course User Guide


DUS704C motion coverage PIR motion detection coverage area: •

9m x 6m

•

At a height of 2.5m

Figure 65

DUS804C and DUS804C-SM motion coverage DUS804C PIR motion coverage area:

DUS804C-SM PIR motion coverage area:

•

5.6m x 7.4m

•

5.0 m circular

•

At a height of 2.5m

•

At a height of 2.5m

Figure 66


Figure 67


63

DUS804C-UP ultra sonic motion coverage Ultrasonic Motion Detection coverage area: •

Major motion detection area: up to 1500 sq. ft * (50 ft x 30 ft)

•

Minor motion detection area: up to 1000 sq. ft * (36 ft x 30 ft)

Figure 68

Motion detection lens pattern

Figure 69

64



Figure 70

Optional motion detector lens for DUS704W In addition to the supplied Wide Angle lens, two other types are available for specific applications: •

DUS704W Curtain – Creates a solid, thin barrier which is useful for monitoring a perimeter in an open space.

•

DUS704W Long Range – Useful for monitoring a long thin space such as a corridor. Contact your local supplier for more details.

Optional Lens – DUS704W Curtain

Figure 71

Figure 72



65

Optional Lens – DUS704W Long Range

Figure 73

Figure 74

Selecting sensor installation locations Selecting the correct location for a motion sensor is of critical concern, incorrect placement can result in sensors not detecting occupants or false triggers (lights turning on incorrectly).

False triggers from passersby

Lights trigger only upon entry

Figure 75

Figure 76

It is possible to reduce the field of view of the DUS804C and DUS804C-SM from their normal 3600 by use of the in-built rotating pull out shield. The shield blocks 1200 of the field of view, reducing the motion detection field area to 2400. The shield can also be rotated to block any 1200 area once the sensor has been installed.

66



Figure 77 – DUS804C shield

By suing the mask installation errors like in figure 55 can be corrected without the need to remount the sensor.

Sensor mounting for PE (photo electric) Follow the points below to ensure sensors operate properly for light sensing: •

Position the sensor so it “sees” a combination of artificial light and natural light.

•

Position the sensor so it not directly exposed to artificial light or sunlight.

•

Keep data cables away from electrical wiring.

Figure 78



67

Infrared receiver mounting location Follow the points below to ensure the sensor operates properly for IR detection: •

Position the sensor so it is within 6 meters of the intended operating position of the infrared transmitter

•

Position the sensor so it is not directly exposed to light, especially incandescent and sunlight, both of which can substantially reduce IR range

•


Figure 79

Installing DUS704W-MB mounting brackets Follow the steps below to mount a wall mount sensor:

68

•

Fix the sensor to a firm section of wall.

•

Position the sensor so it is between 1.1 and 3.1 meters from the floor. Optimum height for the sensor is 2.1meters.

•

Slide the circuit board up or down so the marker on the housing matches up with the installed height on the scale provided on the right hand side of the circuit board.

•

Position the sensor so it is at least 2 meters away from electrical lighting such as neon and fluorescent lights.

•

Position the sensor as to avoid exposing it to direct sunlight and heating / cooling sources.

•


•

Select a location where persons are more likely to walk across the detection “fingers” rather than into them (see Figure 63).

•

For programming instructions refer to Dynalite Tech Note – Setting up Motion Detection functions.



Figure 80



69

Topic 5: Installing touch screens Overview Philips Dynalite currently has two models of color touch screen available, the DTP100 and DTP170. These feature a rich color LCD touch screen that uses vivid graphics and sophisticated on screen controls. Control of various equipment such as lighting, AV, security and HVAC can be easily integrated and controlled from the one location.


Install DTP100 touch screen

•

Install DTP170 touch screen.

General installation points for touch screens •

Remember the display height should be equal to, or slightly below, the eye level of all users.

•

Avoid a location in which bright light is present, either directly in front of, or behind, users.

•

70

Figure 81

The DTP160 Touch Panel must be flush-mounted.


Topic 5: Installing touch screens

Installing the DTP170 Dimensions: •

140mm high x 218mm wide x 71mm deep.

Figure 82

Fixing the device The DTP170 Touch Screen is designed to be flush-mounted, with or without a wall box. •

If using a wall box, separate the wall box from the Touch Screen and make sure no dust or debris enters the Touch Screen during installation.

•

The wall box can then be fixed in place using an appropriate method.



71

Installing the DTP100 Dimensions: •

Hidden Wall box: Height 69mm x Width 129mm x Depth 27mm.

•

Exposed Face: Height 86mm x Width 146mm x Depth 5mm.

Programming port – Type B USB socket

Keyboard/Mouse port – Type B USB socket

DyNet port

3.5mm stereo jack

Ethernet RJ45 network socket Figure 83

72



Fixing the Device The DTP100 Touch screen Panel must be flush-mounted. Separate the wall box from the panel and make sure no dust or debris enters the device during installation. Recommended back box for dry lining / plasterboard applications, use the following part numbers: •

700-279 Wallbox recess metal

•

700-389 Wallbox recess drywall

•

700-280 Wallbox surface mount.

Figure 84 - MK electric 2 gang wall box

Power supply The DTP100 Touchscreen Panel is powered from the DyNet network and does not require mains voltage supply.



73

Topic 6: Installing integration devices Overview In this topic we cover the installation requirements for a number of Philips Dynalite integration devices: •

DDMIDC8 multi function input interface

•

DDNG485 gateway

•

DPMI940 dry contact interface.

Learning outcomes By the end of this topic you’ll be able to •

Install a DDMIDC8

•

Install a DDNG485 gateway

•

Install a DPMI940 dry contact interface

•

Install a DDFCUC024 / DDFCUC010.

Installing the DDMIDC8 Features

74

•

8 x Opto Isolated inputs - each configurable to dry contact or 0-24V input.

•

4 x Analogue Inputs – Configurable to 0-5V or 0-10V.

•

LED Status Indicators – for each opto isolated input.

•

Power Supplied from Network - No mains connection.

•

Powerful Internal PLC - Custom scripts can be written to provide process control based on conditional logic.

•

Simple Installation - DIN Rail mount facilitates installation. Fixing points are provided for installation without the use of DIN rail.


Topic 6: Installing integration devices

Figure 85

Installation notes •

Read Instructions – We recommend that you read this Instruction Manual prior to commencement of installation.

•

Special Programming – This device will only operate in basic modes unless programmed via a computer. If programming is required, contact your local agent for details. Once the data cable is connected to the devices, the factory default settings will allow any control panel or input to operate all channels in all controllers.

•

Mounting Location – Install in a dry, well-ventilated location. Controllers may emit some mechanical noise. Take this into account when deciding the mounting location.

•

Data Cable – Use screened, stranded RS485 data cable with three twisted pairs. Segregate from mains cables by 300mm minimum. Connect devices in a ‘daisy chain’. A data cable that is connected to an energized device is live. Do not cut or terminate live data cables.

D-

+5V

0V

AN4

0V

0-5V/0-10V Analogue Inputs AN3

0V

A/D

+15V

D+ DyNet RS485

GND

SHIELD

µP

A/D

A/D

AN2

0V

AN1 A/D

Input 8

Input 7

Input 6

Input 5

Input 4

Input 3

Input 2

Input 1

Opto Isolated Dry Contact/0-24V AC/DC Digital Inputs

Electrical diagram

Figure 86



75

Analogue fader

AN1 Dynalite 0V DDMIDC8 AN2 Input Interface 0V AN3 0-5V / 0-10V Analogue 0V Inputs AN4 0V +5V Figure 87

Installation steps 1. Mount the device on a DIN rail inside an approved enclosure. The device can also be installed without the use of DIN rail by removing the cover to access two mounting screw holes. 2. Connect RS485 data cable to the serial port as per the connection diagram overleaf. 3. If used, connect volt free contacts or 0-24V AC/DC inputs to any of the 8 opto-isolated inputs. Remove the lid and ensure that the jumpers for each input are set to the appropriate 0-24V or volt free setting, depending on the input type. 4. If any opto-isolated inputs are of the Dry Contact type, ensure that the power supply jumper is fitted in the “volt free” position. Note that this will increase the current consumption of the device from 15mA to 40mA, which may require consideration of voltage drop on long runs of DyNet data cable. 5. If used, connect 0-5V or 0-10V inputs to the analogue ports. Ensure the input voltage is DC and a maximum of 10 Volts. Note that bare faders can also be connected to the analogue inputs by using the adjacent +5V terminal as a supply. Suggested fader value is 10K ohm. Do not attempt to draw more than 25mA from the +5V terminal.

Installing DDNG485 76



1. Mount the device on a DIN rail inside an appropriate enclosure. Alternatively there are 2 holes provided to fix the device to a surface without the use of DIN rail. Remove the front cover to access these holes. 2. Connect data cables to the device as per diagrams. Note that the device is powered from the DyNet network segment that is connected to Port 1. When implementing Repeaters, connect the link to Port 2 of both Gateways. Shielded cable must be used for long runs. When implementing Trunk / Spur topology, connect the Trunk to Port 2 and the Spur to Port 1. Note that up to 150mA of power from the DyNet network on Port 1 is fed to Port 2, so providing there is surplus power available on the Spurs it is normally not necessary to provide a network power supply for the Trunk. 3. If using the device as a DMX receiver, ensure DMX termination rules are obeyed, use a 120 Ohm terminating resistor across D+ and D- at the end of line. Note that Port 2 should be used for DMX Reception.

Figure 88

Figure 89

DPMI940 Topic 6: Installing integration devices


77

Using the DPMI940 To install 3rd party panels in a Dynalite project you will require the use of a DPMI940 dry contact interface.

Figure 90

Figure 91- DPMI940 installed in wall box and connected to switches

Installation steps 1. Mount the device on a DIN rail inside an approved enclosure. The device can also be installed without the use of DIN rail by removing the cover to access two mounting screw holes. 2. Connect RS485 data cable to the serial port as per the connection diagram overleaf. 3. If used, connect volt free contacts or 0-24V AC/DC inputs to any of the 8 opto -isolated inputs. Remove the lid and ensure that the jumpers for each input are set to the appropriate 0-24V or volt free setting, depending on the input type. 4. If any opto-isolated inputs are of the Dry Contact type, ensure that the power supply jumper is fitted in the “volt free” position. Note that this will increase the current consumption of the device from 37mA to 68mA, which may require consideration of voltage drop on long runs of DyNet data cable. 5. If used, connect 0-5V or 0-10V inputs to the analogue ports. Ensure the input voltage is DC and a maximum of 10 Volts. Note that bare faders can also be connected to the analogue inputs by using the adjacent +5V terminal as a supply. Suggested fader value is 10K ohm. Do not attempt to draw more than 25mA from the +5V terminal.

78



Electrical diagram

Figure 92

19 mm

Mounting details

Ribbon Cable

19 mm

40 mm side view

top view Figure 93

Connecting to a motion detector



79

•

Connect Ground and +12V leads to the motion detector’s 0V & +12V terminals.

•

Connect Ground and Switch 1 leads to the motion detector’s Alarm terminals.

•

Connect Ground and Switch 4 leads to the motion detector’s Tamper terminals.

Connecting volt free inputs Inputs: 7 core Flat Ribbon Cable Flying Lead inputs

PIN

FUNCTION

COLOR

1

+12 Volts

Gray with Red Trace

2

Ground

Gray

3

Ground

Gray

4

Switch 1

Gray

5

Switch 2

Gray

6

Switch 3

Gray

7

Switch 4

Gray

To trigger a preset place a short between SW 1, 2, 3 or 4 to the Ground. The +12V terminal is provided to power 3rd party devices such as motion detectors, ensure that it does not touch any other terminal of the device.

Figure 94

80



Install DDFCUC024 / DDFCUC10 The DDFCUC024 is a Fan Coil Unit controller designed for direct connection to components commonly found in air conditioning systems. Triac outputs are provided for controlling heating and cooling liquid valves, relay outputs for driving fan motors, a high capacity relay output is available for electrical heaters. Inputs are provided for a resistive type temperature sensor and the device can use data from a networked temperature sensor such as the Philips Dynalite DTS900. Programmable auxiliary inputs are provided for peripherals such as smoke detectors, motion detectors, window open/close sensors and airflow detectors. The device can be networked with other equipment, such as Philips Dynalite Revolution DRP wall stations and DTP160 touch screen, via an onboard RS485 DyNet port.

Figure 95



81

Topic 7: Testing and troubleshooting Overview Testing and troubleshooting are important aspects to the installation process, this topic covers common issues and methods to troubleshoot network related problems.


Complete the walk through test procedure

•

Find network faults.

Walk through test procedure Once the installation of equipment is complete at test of the devices is required to confirm that they are operating correctly. Simple tests can be performed to confirm functionality of each device on the network. As all channels are set to Area 1 and panels recall presets for Area 1 it is easy to check the network.

LED tracking To check the LED tracking on panels simply hit the buttons on a panel and the indicator LED should illuminate on the button you pressed. Check that other panels buttons also change accordingly to track the button pushes throughout the network.

Luminaires Hit buttons 1 and 4 on a panel to confirm that the luminaires are responding to Area Preset messages for 100% and 0%.

Sensors Check that sensors are working correctly by sending an Area 1 message on the network by hitting button 1 on any panel in the network.

82


Topic 7: Testing and troubleshooting

Touch screens •

Hit the start page button to go to the dimming page

•

Hit the left arrow at the top left of the page

•

Use the sliders on the page to control channels to confirm that it is communicating on the network

Troubleshooting Network Fault finding Once your network is complete, as described earlier. All devices should react to a single push button message. If this is not the case the simplest way to diagnosis the problem is to: •

Break the network into two halves. As you have kept a record of how the network was installed, to find the mid way point should be simple.

•

Try pushing a button again in each half of the network, this will identify which half has the problem.

•

Continue to break this half into quarters and repeat the push button press.

Power Supply faultfinding If the CPU is running (indicated by the 1Hz Flash of the service LED) the power supply to the on board circuits can be considered to be functioning correctly. However some faults in the power supply only become evident when it is loaded down by external loads e.g. DyNet. In a real installation, power consumers connected to DyNet will present a load to the providers power supply. This can be bench tested using a dummy load.

Panel Fault finding When a panel doesn’t respond to network messages try these tips:

Overview

•

Select the panel in Physical view and press the R key on your PC keyboard. A red reset message should appear in the monitor window if the device is online

•

Check that the LED’s are working on the front of the panel and are following the button presses. No LED’s would indicate a possible panel failure or power loss

•

Remove the panel and check the data cable connection for broken wiring. Repair as necessary.


83

•

Use a voltmeter to check the feed voltage. There should be at least 10v DC between the 12v and gnd terminals. If not, an additional network power supply may be required to boost the voltage up to a stable level

•

Factory default the panel in EnvisionProject and reconfigure the device to ensure it is configured correctly.

End of line resistors When to use end of line resistors: •

When cable lengths are close to the maximum limit

•

On high speed networks, for baud rates above 9600

•

Terminate DMX networks.

Common problems Check the following list. If you are still unable to rectify the situation, contact Dynalite. Please ensure that you have completed the following prior to calling our technical support department. •

Check all symptoms in the Troubleshooting list

•

Check for any deviations between the installation and the installation instructions

•

Make a list of the model numbers of all devices used in the system.

SYMPTOM

PROBABLE CAUSE

SOLUTION

Device does not operate at all. No Service LED activity. Power supply indicator LED on PCB not lit.

Incorrect connection of mains supply or no power available.

Check power supply to dimmer. Check Line and Neutral input connections.

Power supply indicator LED lit, but no Service LED activity.

Supply voltage too low, short circuit on network. Control PCB faulty.

Check supply voltage is at least 75% of rated voltage. Check 12V terminal voltages. 12V supply must be present. Disconnect network bus and restore power. Replace control PCB.

Incorrect wiring on serial port. PANIC function activated.

Check serial port wiring, verify control panel operation. Check operation of panic switch if fitted.

Device appears to be operating but all channels at full output.

Device will not respond to control panel push buttons.

84

Control panel incorrectly wired or incorrect configuration.


Check operation of LEDs on control panel. Push button on panel and study response of service LED. Overview

Device operates properly but circuit breakers keep tripping.

Instant tripping: - Short circuit on load. Delayed tripping: - Device overloaded.

Check load wiring for short circuits. Verify device loading with current tester (don’t forget to de-rate for low power-factor loads and transformer losses). Check that the breaker terminals are tight.

Fluorescent lights won’t dim.

Wrong type of ballast or ballast incorrectly wired.

Check ballast type. Check actual wiring against ballast manufacturer’s diagram.

DDMIDC8 Troubleshooting SYMPTOM

PROBABLE CAUSE

SOLUTION

Device does not operate at all. No Service LED activity. Power supply indicator LED on PCB not lit.

Incorrect connection of Mains supply, or no power available.

Check power supply to DNG485. Check Line and Neutral input connections. Check Fuse if fitted.

Power supply indicator LED lit, but no Service LED activity.

Supply voltage too low, short circuit on network or short circuit on analogue inputs. Control PCB faulty.

Check 5V & 12V terminal voltages. Disconnect network bus and restore power. Replace control PCB.

Device appears to be operating but not passing messages.

Incorrect Dip Switch settings. Faulty LTC485 Transceiver.

Verify Dip Switch settings. Replace LTC485 Transceiver.

Device passes messages in one direction only.

Incorrect Dip Switch settings. Incorrect software configuration. Message Pass Filter incorrectly set.

Verify Dip Switch settings. Reload device & verify Message Pass Filter settings. Re compile event file.

Do’s and don’ts of dimming low voltage transformers When dimming low voltage lamps, Dynalite recommends the specification of one lamp per transformer. There are several reasons for this:

Overview

•

In the event of transformer failure, only the single lamp is extinguished. The transformer is also readily accessible as it will be near the extinguished lamp.

•

If larger capacity transformers are used to control multiple lamps, any variances in cable length will be manifested in different luminous outputs; the longer the cable, the less light will be observed coming from the source.


85

•

Some transformers can be noisy when dimmed. This is often the case for larger transformers (especially 'E' and 'I' types), some electronic transformers and toroidal transformers that are potted in a fixture.

•

Large transformers are prone to nuisance tripping with MCB's at switch on, although the soft start features of Dynalite controllers will minimise this risk. The problem is due to the highly inductive nature of the transformer coupled with the high inrush current of the lamps. Sometimes large transformers cannot be avoided for stretched-wire or parallel rod distribution systems. These transformers are usually a component part of the system and should have an integral provision for fast protection against overload or short circuit of the conductors.

•

Large wire-wound transformers have high energy losses and poor output voltage regulation.

•

Some transformers are not suitable for dimming. Please refer to the Dynalite Transformer Compatibility Guide for further information.

•

For effective phase control dimming, minimum loads may apply, depending on the transformer type or load characteristic of the connected lighting fixtures. Lighting circuits comprising a single low voltage fitting of 20W or less may exhibit some instability for this reason. Please refer to controller data sheets or consult a Dynalite representative for advice on minimum loads.

Four-wire transformers (DALI, DSI, 1-10V) require a pair of cables for the control signal, in addition to the mains feed. Local supply regulations must be observed when wiring mains and control cables, as the control terminals on the transformers or controllers are not rated as SELV. Mains voltage must never be applied to the control signal terminals or cables.

Do’s and don’ts of dimming fluorescent lighting In new installations, or when the lamps have been changed, the new lamps should be "burnt in" by being switched full on for at least 100 hours before any attempt is made to switch off or dim them. This will improve the visual dimming performance and lamp life. Please check with the lamp manufacturer for specific advice. Due to the fact that different type and wattage lamps may have different dimming curves, it is advisable not to mix fixtures with different lamp types on the same dimmer channel.

86


Overview

Dynalite Installers Course Training Guide

Recommend Documents