Worked Examples to Eurocode 2.pdf

Licensed copy from CIS: kierg, Kier Group, 12/02/2015, Uncontrolled Copy.

A single copy of this document is licensed to kierg

On 12/02/2015

This is an uncontrolled copy. Ensure use of the most current version of the document by searching the Construction Information Service.

Worked Examples to Eurocode 2 25 February 2010 Amended 18 January 2012

Revisions required to Worked Examples to Eurocode 2 due to Amendment 1 to NA to BS EN 1992-1-1:2004 dated Dec 2009.


Amended 18/1/2012 to illustrate 40K limit on l/d according to Table NA.5 Note 6

Page Where Old text 37/38 3.1.6 Allowable l/d = N u K u F1 u F2 u F3 where N = 25.6 (U = 0.41%, fck = 30) K = 1.0 (simply supported) F1 = 1.0 (beff/bw = 1.0) F2 = 1.0 (span < 7.0 m) F3 = 310/Vs 1.5 where Vs = Vsn (As,req/As,prov) 1/G where Vsn | 242 MPa (From Concise Figure 15.3 and gk/qk = 1.79, \2 = 0.3, Jg = 1.25) G = redistribution ratio = 1.0 ? Vs | 242 u 594/645 = 222 ? F3 = 310/222 = 1.40 ? Allowable l/d = 25.6 u 1.40 = 35.8 Actual l/d = 4800/144 = 33.3 ? OK Use H12 @ 175 B1 (645 mm2/m) 38

3.1.7

By inspection, OK However, if considered critical: V = 29.5 kN/m as before VEd = 29.5 ȭ 0.14 u 12.3 = 27.8 kN/m vEd = 27.8 u 103/144 u 103 = 0.19 MPa vRd,c = 0.53 MPa

Amends to Worked Examples to Eurocode 2 - Jan 2012.doc

Revised text Allowable l/d = N u K u F1 u F2 u F3 where N = 25.6 (U = 0.41%, fck = 30) K = 1.0 (simply supported) F1 = 1.0 (beff/bw = 1.0) F2 = 1.0 (span < 7.0 m) F3 = As,prov /As,req 1.50 = 645/ 594 = 1.09 ? Allowable l/d = 25.6 u 1.09 = 27.9 Actual l/d = 4800/144 = 33.3 ? no good Try 33.3/27.9 x 654 = 784 mm2/m i.e. H12@140 (807 mm2/m) F3 = 807/ 594 = 1.36

? Allowable l/d = 25.6 u 1.36 = 34.8 (which is < 40K = 40) [Table NA.5 Note 6] i.e. > 33.3? OK Use H12 @ 140 B1 (807 mm2/m) By inspection, OK However, if considered critical: V = 29.5 kN/m as before VEd = 29.5 ȭ 0.14 u 12.3 = 27.8 kN/m vEd = 27.8 u 103/144 u 103 = 0.19 MPa U = 804/1000 x 144 =0.56% say 50% curtailed use 0.28% vRd,c = 0.54 MPa

Page 1 of 13


42

3.2.6

F3 = As,prov /As,req 1.50 F3 = 310/Vs 1.5 = 645/ 639 = 1.01 where Allowable l/d = N u K u F1 u F2 u F3 Vs = (fyk/JS) (As,req/As,prov) (SLS = 23.5 u 1.3 u 1.0 u 1.01 loads/ULS loads) (1/G) = 30.8 = fyd u (As,req/As,prov) u (gk + \2 Max. span = 30.8 u 144 = 4435 mm, qk)/(JGgk + JQqk) (1/G) i.e. < 5795 mm = (500/1.15) u (639/645) u [(5.9 ? No good + 0.3 u 3.3)/12.3] u 1.081 = 434.8 u 0.99 u 0.56 u 1.08 = 260 MPa F3 = 310/260 = 1.19 Note: As,prov/As,req d 1.50 Allowable l/d = N u K u F1 u F2 u F3 = 23.5 u 1.3 u 1.0 u 1.19 = 36.4 Max. span = 36.4 u 144 = 5675 mm, i.e. < 5795 mm ? No good Try H12 @ 150 B1 (754 mm2/m) Try H12 @ 125 B1 (904 mm2/m) Vs = 434.8 u 639/754 u 0.56 u 1.08 = 223 F3 = 310/223 = 1.39 Allowable l/d = 23.5 u 1.3 u 1.0 u 1.39 F3 = 904/639 = 1.41 = 42.5 Allowable l/d = 23.5 u 1.3 u 1.0 u 1.41 Max. span = 42.5 u 144 = 6120 mm, = 43.1 i.e. > 5795 mm OK Max. span = 43.1 u 144 = 6206 mm, ? H12 @ 150 B1 (754 mm2/m) OK i.e. > 5795 mm OK ? H12 @ 125 B1 (904 mm2/m) OK

43

3.2.7

F3 = As,req/As,prov 1.5 F3 = 310/Vs 1.5 = 502/ 465 = 1.08 where Vs = fyd u (As,req/As,prov) u (gk + \2 qk)/(JGgk + JQqk) (1/G) = (500/1.15) u (465/502) u [ (5.9 + 0.3 u 3.3)/12.3] u 1.03 = 434.8 u 0.93 u 0.56 u 1.03 = 233 MPa F3 = 310/233 = 1.33 Allowable l/d = N u K u F1 u F2 u F3 = 35.8 u 1.5 u 1.0 u 1.33 Allowable l/d = N u K u F1 u F2 u F3 = 71.4 = 35.8 u 1.5 u 1.0 u 1.08 Max. span = 71.4 u 144 = 10280 mm i.e. > = 58.0 5795 mm OK (which is < 40K = 40 x 1.5 =60) [Table NA.5 Note 6] Max. span = 58.0 u 144 = 8352 mm i.e. > 5795 mm OK

44

3.2.9

In Figure 3.4 H12@150

46

3.2.10a) Crack control As slab < 200 mm, measures to control cracking are unnecessary.

In Figure 3.4 H12@125 Crack control As slab < 200 mm, measures to control cracking are unnecessary.

1

The use of Table 15.2 from Concise Eurocode 2implies certain amounts of redistribution, which are defined in Concise Eurocode 2 Table 15.14. Amends to Worked Examples to Eurocode 2 - Jan 2012.doc

Page 2 of 13

However, as a check on end span: However, as a check on end span: Loading is the main cause of cracking, Loading is the main cause of cracking, ? use Table 7.2N or Table 7.3N for wmax = 0.4 ? use Table 7.2N or Table 7.3N for wmax = 0.4 mm and V = 241 MPa (see deflection check). mm and V = 241 MPa (see deflection check). Max. bar size = 20 mm Max. bar size = 20 mm or max. spacing = 250 mm or max. spacing = 250 mm ? H12 @ 150 B1 OK. ? H12 @ 125 B1 OK

46

End supports: effects of partial fixity

End supports: effects of partial fixity

Try H12 @ 450 (251 mm2/m) U-bars at supports

Try H12 @ 500 (226 mm2/m) U-bars at supports

3.2.10b) End span, bottom reinforcement Try H12 @ 300 (376 mm2/m) at supports


49

51

End span, bottom reinforcement Try H12 @ 250 (452 mm2/m) at supports

3.2.10b) Supporrt B bottom steel at support iii For convenience use H12 @ 300 B1 (376 mm2/m)

Support B bottom steel at support

3.2.11

See A below

Figure 3.6

57/58 3.3.5b) Span A®®B: Deflection

For convenience use H12 @250 B1 (452 mm2/m) Span A® ®B: Deflection

F3 = 310/Vs 1.5 F3 = 310/Vs 1.5 where where Vs = (fyk/JS) (As,req/As,prov) (SLS Vs = (fyk/JS) (As,req/As,prov) (SLS loads/ULS loads) (1/G) loads/ULS loads) (1/G) = 434.8(523/628) [ (4.30 + = 434.8(523/628) [ (4.30 + 0.3 u 5.0)/13.38] (65.3/61.7$) 5.0)/13.38] (65.3/61.7$) = 434.8 u 0.83 u 0.70 u 1.06 = 434.8 u 0.83 u 0.43 u 1.06 = 267 MPa = 164 MPa F3 = 310/Vs F3 = 310/Vs = 310/267 = 1.16 = 310/164 = 1.89# but 1.50 therefore say 1.50 ? Permissible l/d = 22.8 u 1.3 u 0.8 u 0.93 u ? Permissible l/d = 22.8 u 1.3 u 0.8 u 0.93 u 1.16 = 25.6 1.50 = 33.0 Actual l/d = 7500/257 = 29.2 Actual l/d = 7500/257 = 29.2 ?no good ? OK Use 2 no. H20/rib (628 mm2/rib) Try 1H25 + 1H20/rib (805 mm2/rib) d = 254 mm; K = 0.028; z = 241 mm Asreq = 529 mm2 ? Vs = 434.8(529/805) [ (4.30 + 5.0)/13.38] (65.3/61.7$) = 434.8 u 0.66 u 0.70 u 1.06 = 213 MPa F3 = 310/213 = 1.45 Permissible l/d = 22.8 u 1.3 u 0.8 u 0.93 u 1.45 = 32.0 Actual l/d = 7500/254 = 29.5 ? OK Use 1H25 + 1H20/rib (805 mm2/rib)


Page 3 of 13


61

3.3.6b) Span B®C C ® : Deflection

Span B®C C ® : Deflection

F3 = 310/VS 1.5 F3 = 310/VS 1.5 where where Vs = (fyk/Js) (As,req/As,prov) (SLS loads/ULS Vs = (fyk/Js) (As,req/As,prov) (SLS loads/ULS loads) (1/G) loads) (1/G) = 434.8 u (474/628) [(4.30 + 0.3 u = 434.8 u (474/628) [(4.30 + 5.0) 5.0)/13.38](61.1/55.9) /13.38](61.1/55.9) = 434.8 u 0.75 u 0.43 u 1.09 = 434.8 u 0.75 u 0.70 u 1.09 = 153 MPa = 249 MPa F3 = 310/Vs F3 = 310/Vs = 310/153 = 2.03, say = 1.502 = 310/249 = 1.24 ? Permissible l/d = 26.8 u 1.5 u 0.8 u 0.77 ? Permissible l/d = 26.8 u 1.5 u 0.8 u 0.77 u 1.50 = 37.1 u 1.24 = 30.7 Actual l/d = 9000/257 = 35 Actual l/d = 9000/257 = 35 ? ? no good OK ?Use 2 H20/rib (628 mm2/rib) Try 1H25 + 1H20/rib (805 mm2/rib) d = 254 mm; K = 0.025; z = 241 mm Asreq = 480 mm2 ? Vs = 434.8(480/805) [ (4.30 + 5.0)/13.38] (61.1/55.9) = 434.8 u 0.60 u 0.70 u 1.09 = 199 MPa F3 = 310/199 = 1.56 but 1.50 Permissible l/d = 26.8 u 1.5 u 0.8 u 0.77 u 1.50 = 37.1 Actual l/d = 9000/254 = 35.4 ? OK Use 1H25 + 1H20/rib (805 mm2/rib) 65

3.3.10

69

3.3.10b) Support B (and C): bottom steel curtailment viii BA and BC To suit prefabrication 2 no. H20/rib will be curtailed at solid/rib interface, 1000 mm from BA (B towards A) and BC.

Support B (and C): bottom steel curtailment BA and BC To suit prefabrication 1 H20 + 1H25 /rib will be curtailed at solid/rib interface, 1000 mm from BA (B towards A) and BC.

69

3.3.10c) Laps At AB, check lap 1 no. H20 B to 2 no. H20 B in rib full tension lap: l0 = D1 D6 lb,rqd > l0,min where D1 = 1.0 (cd = 45 mm, i.e. < 3M) D6 = 1.5 (as > 50% being lapped) lb,rqd = (M/4) (Vsd/fbd) where M = 20 Vsd = 434.8 = 3.0 MPa as before fbd

Laps At AB, check lap 1 no. H20 B to 1 H20 B + 1H25 B in rib full tension lap: l0 = D1 D6 lb,rqd > l0,min where D1 = 1.0 (cd = 45 mm, i.e. < 3M) D6 = 1.5 (as > 50% being lapped) lb,rqd = (M/4) (Vsd/fbd) where M = 20 Vsd = 434.8 (bar assumed to be fully stressed) fbd = 3.0 MPa as before

65

3.3.10d) Figure 3.17

See C below

74

3.4.5b) F3 = 310/Vs 1.5 where

F3 = 310/Vs 1.5 where

Figure 3.15

See B below

2

Both As,prov/As,req and any adjustment to N obtained from Expression (7.16a) or Expression (7.16b) is restricted to 1.5 by Note 5 to Table NA.5 in the UK NA. Amends to Worked Examples to Eurocode 2 - Jan 2012.doc

Page 4 of 13


Vs = Vsn (As,req/As,prov) 1/G

Vs = Vsn (As,req/As,prov) 1/G where where Vsn = (500/1.15) u (8.5 + 0.3 u 4.0) Vsn = (500/1.15) u (8.5 + 4.0) /16.6 = /16.6 = 254 MPa 327 MPa (or | 253 MPa (From Concise Figure 15.3 for Gk/Qk = 2.1, \2 = 0.3 and Jg = 1.25) G = redistribution ratio = 1.03 G = redistribution ratio = 1.03 Vs | 327 u (1324/1570)/1.03 = 267 ? ? Vs | 253 u (1324/1570)/1.03 = 207 ? F3 = 310/267 = 1.16 ? F3 = 310/207 = 1.50 ? Allowable l/d = 20.3 u 1.2 u 1.16 = 28.2 ? Allowable l/d = 20.3 u 1.2 u 1.50 = 36.5 Actual l/d = 9500/260 = 36.5 ?no good Actual l/d = 9500/260 = 36.5 ? OK Try H16 @100 (2010 mm2/m) and Use H20 @ 200 B1 (1570) F3 = As,prov /As,req 1.50 = 2010/ 1340 = 1.50 1.50 ? Allowable l/d = 20.3 u 1.2 u 1.50 = 36.5 Actual l/d = 36.5 ? OK Use H16@100B1 (2093 mm2/m) 78

3.4.7b) Allowable l/d = N u K u F1 u F2 u F3 Allowable l/d = N u K u F1 u F2 u F3 where where N = 26.2 (U = 0.40%, fck = 30) N = 26.2 (U = 0.40%, fck = 30) K = 1.2 (flat slab) K = 1.2 (flat slab) F1 = 1.0 (beff/bw = 1.0) F1 = 1.0 (beff/bw = 1.0) F2 = 1.0 (no brittle partitions) F2 = 1.0 (no brittle partitions) F3 = As,prov /As,req 1.50 F3 = 310/Vs = 1005/ 959 = 1.05 1.50 where Vs = Vsn (As,req/As,prov) 1/G where Vsn | 283 MPa (from Concise Figure 15.3 and Gk/Qk = 3.6, \2 = 0.3, Jg = 1.25) G = redistribution ratio = 1.08 ? Vs | 283 u (959/1005)/1.08 = 250 ? F3 = 310/250 = 1.24 ?Allowable l/d = 26.2 u 1.2 u 1.24 = 39.0 ?Allowable l/d = 26.2 u 1.2 u 1.05 = 33.0 Actual l/d = 5900/240 = 24.5 ? OK Actual l/d = 5900/240 = 24.5 ? OK Use H16 @ 200 B2 (1005 mm2/m) Use H16 @ 200 B2 (1005 mm2/m)

90

3.4.13

Spans 1®2 and 2®3: Column strip and middle strip: H20 @ 200 B

Spans 1®2 and 2®3: Column strip and middle strip: H16 @ 100 B1

92

3.4.13

Figure 3.26

See D below

112

4.2.6

F3 = 310/Vs 1.5 where

F3 = As,prov /As,req 1.50 = 4824/4158 = 1.16

Vs in simple situations = (fyk/JS) (As,req/As,prov) (SLS loads/ULS loads) (1/G). However in this case separate analysis at SLS would be required to determine Vs. Therefore as a simplification use the conservative assumption: 310/Vs = (500/fyk) (As,req/As,prov) = (500/500)u(4824/4158) = 1.16


Page 5 of 13


123

4.3.5b) F3 = 310/Vs 1.5 where Vs=(fyk/JS)(As,req/As,prov)(SLS loads/ULS loads)(1/G) =434.8u(5835/5892) [(47.8+0.3u45.8)/(1.25 u 47.8 + 1.5 u 45.8)] u (1/0.945) = 434.8 u 0.99 u 0.48 u 1.06 = 219 MPa

124

4.3.5b)

F3 = As,prov /As,req 1.50 = 5892/5835= 1.01

F3 = 310/Vs 1.5 = 310/219 = 1.41 ? Permissible l/d= 17.8u1.3 u0.90u0.95 u1.41 = 27.9 ?Permissible l/d= 17.8u1.3 u0.90u0.95 u1.01 = 20.0 Actual l/d = 7500/252 = 29.8 ? no good Actual l/d = 7500/252 = 29.8 ? no good Try 12 no. H32 B (9648 mm2) Try 13 no. H25 B (6383 mm2) F3 = As,prov /As,req 1.50 F3 = 310/Vs 3 = 9648 /5835 = 1.654 = say 1.50 = 310/219 u 13/12 = 1.53 = say 1.50 ? Permissible l/d = 17.8u1.3u0.90u0.95u1.50 = 29.7 ? Permissible l/d = 17.8u1.3u0.90u0.95u1.50 = 29.7 Actual leff/d = 7400/252 = 29.8 Actual leff/d = 7400/252 = 29.8 Say OK Say OK 2 Use 13 no. H25 B (6383 mm2) Use 13 no. H25 B (6383 mm )

124

4.3.6

127

4.3.7d) F3 = 310/Vs 1.5 F3 = As,prov /As,req 1.50 = 3828/3783= 1.01 where Vs=(fyk/JS)(As,req/As,prov)(SLS loads/ULS loads)(1/G) =434.8u (3783/3828)[(47.8+0.3u 45.8)/(1.25 u 47.8 + 1.5 u 45.8)] u (1/0.908) = 434.8 u 0.99 u 0.48 u 1.10 = 227 MPa F3 = 310/Vs = 310/227 = 1.37 ? Permissible l/d = 44.7 u 1.37 u 0.88 u 0.95 ? Permissible l/d u 1.37 = 70.1 = 44.7 u 1.50 u 0.88 u 0.95 u 1.01 = 56.6 Actual l/d = 7500/252 = 29.8 ? OK Use 8 no. H25 B (3928 mm2) (which is < 40K = 40 x 1.5 =60) [Table NA.5 Note 6]

Figure 4.20

See E below

Actual l/d = 7500/252 = 29.8 ? OK Use 8 no. H25 B (3928 mm2 133

4.3.10

Figures 4.22 and 4.23

See F below

146

5.3

Figure 5.6 300 mm flat slabs All columns 400 mm sq

300 mm flat slabs All columns 500 mm sq

153

5.3.8

2WP]VTa`TÓ³S

183

References

183

References

1a National Annex to Eurocode 2- Part 1- 1a National Annex to Eurocode 2- Part 11. BSI 2005 1. Incorporating Amendment No.1 BSI 2009 5 R S NARAYANAN & C H GOODCHILD. 5 R S NARAYANAN & C H GOODCHILD. The Concrete Centre. Concise Eurocode The Concrete Centre. Concise Eurocode 2, CCIP-005. TCC 2006 2, CCIP-005. TCC 2006 As Amended

3

Both As,prov/As,req and any adjustment to N obtained from Expression (7.16a) or Expression (7.16b) is restricted to 1.5 by Note 5 to Table NA.5 in the UK NA. 4 Both As,prov/As,req and any adjustment to N obtained from Expression (7.16a) or Expression (7.16b) is restricted to 1.5 by Note 5 to Table NA.5 in the UK NA. Amends to Worked Examples to Eurocode 2 - Jan 2012.doc

Page 6 of 13

190

B1.1

Delete existing text. See G below

2010 New text: According to Note 5 of Table NA.5 the NA [1a] to BS EN 1992-1-1 the modification factor for service stress used with the l/d method of checking the SLS state of deformation (designated factor F3 in TCC publications) may be determined as either x

310/Vs using characteristic load combinations to determine the service stress, Vs

or


x

(500/fyk)(As,prov /As,req)

In either case the modification factor is restricted to a maximum of 1.50. In the UK fyk = 500 MPa. Assuming Vs is proportional to Vu, and using characteristic load combinations to determine Vs produces values of 310/Vs = 1.00 +3% - 6%. and so is not as attractive to using As,prov /As,req. The use of F3 = As,prov /As,req 1.5 is therefore advocated in checking deformation using the l/d method. 190 191 191 201 204

B1.2 B1.4 B1.5 C7 C8

See H below See J below See K below See L below See M below


Page 7 of 13

A Amends to p 51 Figure 3.7

300 250 150 125


300 250

B Amends to p 65 Figure 3.15

2H20/rib 1H25 + 1H20/rib x3

C Amends to p 70 Figure 3.17

2H20/rib 1H25 + 1H20/rib x2 Note curtailed bat


Page 8 of 13

D Amends to p 92 Figure 3.26


H20@200 H16@100

E Amends to p 124 Figure 4.20

25 bar 32 bar

20 bar 20/25 bar


Page 9 of 13

F Amends to p133 Figures 4.22 and 4.23

13H25 12H32


x2 T25 in section x2

G Amends to p190 B1.1 NewText According to Note 5 of Table NA.5 the NA to BS EN 1992-1-1[1a] the modification factor for service stress used with the l/d method of checking the SLS state of deformation (designated factor F3 in TCC publications) may be determined as either x


x


or

In either case the modification factor is restricted to a maximum of 1.50. In the UK fyk = 500 MPa. Assuming Vs is simply proportional to the ultimate stress, Vu, produces values of 310/Vs = 1.00 +/- 5% and so for hand calculations is not as attractive as using As,prov /As,req. The use of F3 = As,prov /As,req 1.5 is therefore advocated in checking deformation using the l/d method by hand.


Page 10 of 13

H Amends to p190 B1.2 combination values of actions combination values of actions taking account of SLS moments, compression reinforcement, As,prov /As,req, etc.

[1]


310/Vs

NewText

[1a]

an accurate

J Amends to p191 B1.4

were

Add new text

using the quasi permanent values of actions (see B.4)

New para

In the light of the above disparity and pending clarification, the UK NA was revised and published in December 2009 as detailed in B1.1 above.


Page 11 of 13

K Amends to p191 B1.4


New paras

Prior to the publication of the revised UK NA[1a] it was allowable to calculate the moderation factor using in l/d verifications of deformation(F3) by using quasi permanent loads. Assuming Vs due to quasi permanent actions is proportional to Vu, the method as outlined in C8 may be used to determine Vs in verifications of crack widths, etc.

L Amends to p201 C7

New text: either x


x


or

In either case the modification factor is restricted to a maximum of 1.50.


Page 12 of 13

M Amends to p204 C8


below

New text ex p 201:

chg 25 Feb 2010


Page 13 of 13

: cement Zg] concrete bg]nlmkr in[eb\Zmbhg


Phkd^]>qZfie^l mh>nkh\h]^+3Ohenf^* ?hkma^]^lb`gh_bg&lbmn\hg\k^m^ê^f^gmlbg_kZf^][nbe]bg`l

mh;L>G*22+&*&*3+))-Zg]bmlNDGZmbhgZe:gg^q3+)).

g`F^mZe

?hk^phk] The introduction of European standards to UK construction is a significant event as, for the first time, all design and construction codes within the EU will be harmonised. The ten design standards, known as the Eurocodes, will affect all design and construction activities as all current British Standards for structural design are due to be withdrawn in 2010. The cement and concrete industry recognised the need to enable UK design professionals to use Eurocode 2, Design of concrete structures, quickly, effectively, efficiently and with confidence. Supported by government, consultants and relevant industry bodies, the Concrete Industry Eurocode 2 Group (CIEG) was formed in 1999 and this Group has provided the guidance for a coordinated and collaborative approach to the introduction of Eurocode 2.


As a result, a range of resources are being delivered by the concrete sector (see www.eurocode2.info). The aim of this publication, Worked Examples to Eurocode 2: Volume 1 is to distil from Eurocode 2, other Eurocodes and other sources the material that is commonly used in the design of concrete framed buildings. These worked examples are published in two parts. Volume 2 will include chapters on Foundations, Serviceability, Fire and Retaining walls.

:\dghpe^]`^f^gml The original ideas for this publication emanates from the research project Èurocode 2: Transition from UK to European concrete design standards’, which was led by the BCA and part funded by the DTI under their PII scheme and was overseen by a Steering Group and the CIEG. The work has been brought to fruition by The Concrete Centre from early initial drafts by various authors listed on the inside back cover. The concrete industry acknowledges and appreciates the support given by many individuals, companies and organisations in the preparation of this document. These are listed on the inside back cover. We gratefully acknowledge the authors of the initial drafts and the help and advice given by Robin Whittle in checking the text. Thanks are also due to Gillian Bond, Kevin Smith, Sally Huish and the design team at Michael Burbridge Ltd for their work on the production. The copyright of British Standards extracts reproduced in this document is held by the British Standards Institution (BSI). Permission to reproduce extracts from British Standards is granted by BSI under the terms of Licence No: 2009RM010. No other use of this material is permitted. This publication is not intended to be a replacement for the standard and may not reflect the most up-to-date status of the standard. British Standards can be obtained in PDF or hard copy formats from the BSI online shop: http://shop.bsigroup.com or by contacting BSI Customer Services for hard copies only: Tel:+44 (0)20 8996 9001, Email: [email protected].

In[ebla^][rMa^
2

Phkd^]>qZfie^l mh>nkh\h]^+3Ohenf^*

Lrf[hel

bb

-

;^Zfl

20

-')

@^g^kZe

20

*

Bgmkh]n\mbhg

*

-'*

*'*

:bf

*

-'+

A^ZoberehZ]^]E&[^Zf

*)-

*'+

>nkh\h]^3;Zlblh_lmkn\mnkZe]^lb`g

,

-',

**2

*',

>nkh\h]^*3:\mbhglhglmkn\mnk^l

-

*'-

>nkh\h]^+3=^lb`gh_\hg\k^m^lmkn\mnk^l

-

.

*,-

*'.

GZmbhgZe:gg^q^l

.

.')

@^g^kZe

*,-

*'/

;Zlblh_ma^phkd^]^qZfie^lbgmablin[eb\Zmbhg .

.'*

>]`^\henfg

*,.

*'0

:llnfimbhgl

/

.'+

I^kbf^m^k\henfg!bgm^kgZe^gobkhgf^gm"

*,2

*'1

FZm^kbZeikhi^kmb^l

/

.',

Bgm^kgZe\henfg

*-/

*'2

>q^\nmbhg

/

.'-

+

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml

0

L fZeei^kbf^m^k\henfgln[c^\m mhmph&ahnk_bk^k^lblmZg\^

*.0

+'*

F^mah]lh_ZgZerlbl

0

/

PZeel

*//

+'+

:\mbhgl

0

/')

@^g^kZe

*//

+',

0

/'*

La^ZkpZee

*/0

+'-

OZkbZ[e^Z\mbhgl3bfihl^]ehZ]l

1

+'.

OZkbZ[e^Z\mbhgl3lghpehZ]l

*+

0

K^_^k^g\^lZg]_nkma^kk^Z]bg`

*1,

+'/

OZkbZ[e^Z\mbhgl3pbg]ehZ]l

*,

:ii^g]bq:3 =^kbo^]_hkfneZ^

*1.

+'0

OZkbZ[e^Z\mbhgl3hma^kl

*0

+'1

I^kfZg^gmZ\mbhgl

*1

:ii^g]bq;3 L^kob\^Z[bebmrebfbmlmZm^

*2)

+'2

=^lb`goZen^lh_Z\mbhgl

+*

:ii^g]bq<3 =^lb`gZb]l

*2-

21

+'*) EhZ]ZkkZg`^f^gmh_Z\mbhgl3bgmkh]n\mbhg

+.

+'** E hZ]ZkkZg`^f^gmlZ\\hk]bg`mhma^ NDGZmbhgZe:gg^qmh>nkh\h]^

+.

+'*+ >qZfie^lh_ehZ]bg`

+0

,

LeZ[l

,.

Li^\bZe]^mZbel3lmknmmb^

,')

@^g^kZe

,.

L^kob\^Z[bebmr

,'*

Lbfierlniihkm^]hg^&pZrleZ[

,/

?bk^

,'+

-)

K^mZbgbg`pZee

,',

.+

K^_^k^g\^lZg]_nkma^kk^Z]bg`

,'-

?eZmleZ[

0*

:ii^g]bq:3=^kbo^]_hkfneZ^

,'.

LmZbk_ebàm

2.

:ii^g]bq;3=^lb`gZb]l

Ohenf^+!in[ebla^]lîZkZmêr" ?hng]Zmbhgl

i


Symbols and abbreviations used in this publication Symbol

Definition

:

:

Lbm^Zembmn]^%f!lghp"

:

:embmn]^h_ma^lbm^bgf^mk^lZ[ho^f^Zgl^Zeôê!pbg]"

:%;%<

OZkbZ[e^lnl^]bgma^]^m^kfbgZmbhgh_lebf

:\

:]

=^lb`goZen^h_ZgZ\\b]^gmZeZ\mbhg

:>]

=^lb`goZen^h_Zl^blfb\Z\mbhg

:k^_

K^_^k^g\^Zk^Zh_ma^lmkn\mnk^hklmkn\mnkZeê^f^gm!pbg]"

:l

:l%fbg

Fbgbfnf\khll&l^\mbhgZeZk^Zh_k^bg_hk\^f^gm

:l%ikho

:k^Zh_lm^êikhob]^]

:l%k^j

:k^Zh_lm^êk^jnbk^]

:l*

:k^Zh_k^bg_hk\bg`lm^êbgeZr^k*

:l+

:k^Zh_\hfik^llbhglm^ê!bgeZr^k+"

:le

:k^Zh_ma^m^glbe^k^bg_hk\^f^gm^qm^g]bg`Zme^Zlme[]$][^rhg]ma^l^\mbhg\hglb]^k^]

:lF!:lG"

M hmZeZk^Zh_k^bg_hk\^f^gmk^jnbk^]bglrff^mkb\Ze%k^\mZg`neZk\henfglmhk^lblmfhf^gm!ZqbZeehZ]"nlbg` lbfieb_b^]\Ze\neZmbhgf^mah]

:lp

khll&l^\mbhgZeZk^Zh_la^Zkk^bg_hk\^f^gm4:k^Zh_ing\abg`la^Zkk^bg_hk\^f^gmbghgî^kbf^m^kZkhng]ma^ < \henfg

:lp%fbg

bgbfnf\khll&l^\mbhgZeZk^Zh_la^Zkk^bg_hk\^f^gm4FbgbfnfZk^Zh_ing\abg`la^Zkk^bg_hk\^f^gmbghg^ F i^kbf^m^kZkhng]ma^\henfg

:m

:k^Zh_m^glbe^k^bg_hk\^f^gmbg_eZmleZ[\henfglmkbil

Z

=blmZg\^%ZeehpZg\^Zmlniihkml

Z

:qbl]blmZg\^_khfma^\hg\k^m^lnk_Z\^mhma^\^gmk^h_ma^[Zk!_bk^"

Z

:g^qihg^gm!bg\hglb]^kbg`[bZqbZe[^g]bg`h_\henfgl"

Z

Ikhc^\mbhgh_ma^_hhmbg`_khfma^_Z\^h_ma^\henfghkpZee

Ze

blmZg\^[rpab\amaêh\Zmbhgpa^k^Z[Zkblghehg`^kk^jnbk^]_hk[^g]bg`fhf^gmbl]blieZ\^]mhZeehp_hkma^ = _hk\^l_khfma^mknllfh]ê_hkla^Zk'!ÂLab_mÃ]blmZg\^_hk\nkmZbef^gm"

Z*%Z+%

=blmZg\^_khf^]`^h_lniihkmmh\^gmk^h_lniihkm

Z*%[*

=bf^glbhglh_ma^\hgmkhei^kbf^m^kZkhng]Zgêhg`Zm^]lniihkm!ing\abg`la^Zk"

Z'f'l'e'

:embmn]^Z[ho^f^Zgl^Zeôê

[

Ho^kZeepb]mah_Z\khll&l^\mbhg%hk_eZg`^pb]mabgZM&hkE&[^Zf

[

;k^Z]mah_[nbe]bg`!pbg]"

[^

>__^\mbo^pb]mah_Z_eZmleZ[!Z]cZ\^gmmhi^kbf^m^k\henfg"

[^__

>__^\mbo^pb]mah_Z_eZg`^

[^j!a^j"

>jnboZe^gmpb]ma!a^bàm"h_\henfg6[!a"_hkk^\mZg`neZkl^\mbhgl

[fbg

Fbgbfnfpb]mah_p^[hgM&%B&hkE&[^Zfl

[m

F^Zgpb]mah_ma^m^glbhgshg^'?hkZM&[^Zfpbmama^_eZg`^bg\hfik^llbhg%hgerma^pb]mah_ma^p^[blmZd^g bgmhZ\\hngm

[p

Pb]mah_ma^p^[hgM&%B&hkE&[^Zfl'Fbgbfnfpb]ma[^mp^^gm^glbhgZg]\hfik^llbhg\ahk]l

[*

AZe_h_]blmZg\^[^mp^^gZ]cZ\^gmp^[lh_]hpglmZg][^Zfl

<^

>qihlnk^\h^__b\b^gm!lghp"

Ma^kfZe\h^__b\b^gm!lghp"

La^Zk\^gmk^

ii


Symbol

Definition

\*%\+

bf^glbhglh_Zk^\mZg`neZk\henfg'?hk^]`^\henfgl%\*blf^Zlnk^]i^ki^g]b\neZkmhma^_k^^^]`^!ing\abg` = la^Zk"

\Zem

:embmn]^_Z\mhk!pbg]"

\]

=rgZfb\_Z\mhk!pbg]"

\]bk

=bk^\mbhgZe_Z\mhk!pbg]"

\^%_eZm

>qihlnk^_Z\mhk!pbg]"

\_

?hk\^\h^__b\b^gm!pbg]"

\fbg

Fbgbfnf\ho^k%!]n^mhma^k^jnbk^f^gml_hk[hg]%\fbg%[hk]nkZ[bebmr\fbg%]nk"

\ghf

GhfbgZe\ho^k'GhfbgZe\ho^klahne]lZmbl_rma^fbgbfnfk^jnbk^f^gmlh_[hg]%]nkZ[bebmrZg]_bk^

\i^

!>qm^kgZe"ik^llnk^\h^__b\b^gm!pbg]"

\i^%*)

!>qm^kgZe"ik^llnk^\h^__b\b^gm_hkZk^Zl7*f+!pbg]"

\ib

Bgm^kgZeik^llnk^\h^__b\b^gm!pbg]"

\ikh[

Ikh[Z[bebmr_Z\mhk!pbg]"

\l^Zlhg

L^Zlhg_Z\mhk!pbg]"

\l

Lbs^_Z\mhk!pbg]"

\r%\q

D\]ô

:eehpZg\^fZ]^bg]^lb`g_hk]ôbZmbhg

=

=bZf^m^kh_Z\bk\neZk\henfg4=bZf^m^k

]

>__^\mbo^]îmamhm^glbhglm^ê

]+

>__^\mbo^]îmamh\hfik^llbhglm^ê

]\

>__^\mbo^]îmah_\hg\k^m^bg\hfik^llbhg

>

>__^\mh_Z\mbhg4Bgm^`kbmr!bg_bk^"4>eZlmb\fh]nenl

>\]

=^lb`goZen^h_fh]nenlh_êZlmb\bmrh_\hg\k^m^

>\f

L^\Zgmfh]nenlh_êZlmb\bmrh_\hg\k^m^

>I

;^g]bg`lmb__g^ll

>l

=^lb`goZen^h_fh]nenlh_êZlmb\bmrh_k^bg_hk\bg`lm^ê

>qi'

>qik^llbhg

>JN

LmZmb\^jnbeb[kbnf

^

>\\^gmkb\bmr

^)

Fbgbfnf^\\^gmkb\bmrbg\henfgl

^+

=^_e^\mbhg!nl^]bgZll^llbg`F+bgle^g]^k\henfgl"

^b

>\\^gmkb\bmr]n^mhbfi^k_^\mbhgl

^r%^s

>\\^gmkb\bmr%F>] (O>]Zehg`rZg]sZq^lk^li^\mboêr!ing\abg`la^Zk"

?*

?Z\mhkmhZ\\hngm_hk_eZg`^]l^\mbhgl!]^_e^\mbhg"

?+

?Z\mhkmhZ\\hngm_hk[kbmmeîZkmbmbhglbgZllh\bZmbhgpbmaehg`liZgl!]^_e^\mbhg"

?,

?Z\mhkmhZ\\hngm_hkl^kob\^lmk^llbgm^glbe^k^bg_hk\^f^gm!]^_e^\mbhg"

?

:\mbhg

?>F

?bq^]^g]fhf^gm

?\!?l"

?hk\^bg\hg\k^m^!lm^ê"

?]

=^lb`goZen^h_ZgZ\mbhg

?>

M^glbe^_hk\^bgk^bg_hk\^f^gmmh[^Zg\ahk^]

?d

?kî

Kîk^l^gmZmbo^Z\mbhg!6r?dpa^k^r6_Z\mhkmh\hgo^km\aZkZ\m^kblmb\mhkîk^l^gmZmbo^Z\mbhg"

?l

M^glbe^_hk\^bgk^bg_hk\^f^gm

?m]

=^lb`goZen^h_ma^m^glbe^_hk\^bgehg`bmn]bgZek^bg_hk\^f^gm

D?m]

:]]bmbhgZem^glbe^_hk\^bgehg`bmn]bgZek^bg_hk\^f^gm]n^mhma^mknllla^Zkfh]ê iii


Symbol

Definition

?O%>]

MhmZeo^kmb\ZeehZ]!hg[kZ\^]Zg][kZ\bg`f^f[^kl"

?p

K^lnemZgm\aZkZ\m^kblmb\_hk\^]n^mhpbg]'!L^^l^\mbhg+'/"

_[]

NembfZm^[hg]lmk^ll

_\]

=^lb`goZen^h_\hg\k^m^\hfik^llbo^lmk^g`ma

_\d

_\m%]

=^lb`gm^glbe^lmk^g`mah_\hg\k^m^!a\m _\m%d (g<"

_\m%d

_\mf

F^ZgoZen^h_ZqbZem^glbe^lmk^g`mah_\hg\k^m^

_l\

_r]

=^lb`grbê]lmk^g`mah_ehg`bmn]bgZek^bg_hk\^f^gm%:le

_rd

_rp]

=^lb`grbê]lmk^g`mah_ma^la^Zkk^bg_hk\^f^gm

_rp]%^_

>__^\mbo^]^lb`glmk^g`mah_ing\abg`la^Zkk^bg_hk\^f^gm

_rpd

@d

@d%lni

Nii^k\aZkZ\m^kblmb\oZen^h_Zi^kfZg^gmZ\mbhg

@d%bg_

Ehp^k\aZkZ\m^kblmb\oZen^h_Zi^kfZg^gmZ\mbhg

`d

Ab

AhkbshgmZeZ\mbhgZiieb^]ZmZeôê

A

A^bàmh_[nbe]bg`!pbg]"

a

Ho^kZee]îmah_Z\khll&l^\mbhg4A^bàm

aZo^

H[lmkn\mbhga^bàm!pbg]"

a]bl

=blieZ\^f^gma^bàm!pbg]"

a_

=îmah__hhmbg`4Mab\dg^llh__eZg`^

al

=îmah_leZ[

I

L^\hg]fhf^gmh_Zk^Zh_\hg\k^m^l^\mbhg4Bg^kmbZ

I

BglneZmbhg!bg_bk^"

b

KZ]bnlh_`rkZmbhg

D

F>] ([] +_\d':f^Zlnk^h_ma^kêZmbo^\hfik^llbo^lmk^llbgZf^f[^kbg_e^qnk^

D

?Z\mhkmhZ\\hngm_hklmkn\mnkZelrlm^f!]^_e^\mbhg"

D

OZen^h_DZ[ho^pab\a\hfik^llbhgk^bg_hk\^f^gmblk^jnbk^]

Do

:\hkk^\mbhg_Z\mhk_hkZqbZeehZ]

Df

:\hkk^\mbhg_Z\mhk_hk\k^î

d

d

KêZmbo^_e^qb[bebmrhkkêZmbo^lmb__g^ll

e

e

A^bàmh_ma^lmkn\mnk^bgf^mk^l

e!hkE"

E^g`ma4LiZg

e)

>__^\mboê^g`ma!h_\henfgl"

e)

=blmZg\^[^mp^^gihbgmlh_s^khfhf^gm

e)

=^lb`geZie^g`ma

e)%_b

>__^\mboê^g`mang]^k_bk^\hg]bmbhgl

e[

;Zlb\Zg\ahkZ`ê^g`ma

e[]

=^lb`gZg\ahkZ`ê^g`ma

e[%^j

>jnboZe^gmZg\ahkZ`ê^g`ma

e[%fbg

FbgbfnfZg\ahkZ`ê^g`ma

iv


Symbol

Definition

e[%kj]

;Zlb\Zg\ahkZ`ê^g`ma

e^__

>__^\mbo^liZg

eg

er%es

LiZglh_Zmph&pZrleZ[bgma^rZg]s]bk^\mbhgl

F

;^g]bg`fhf^gm'Fhf^gm_khf_bklmhk]^kZgZerlbl

F

Fhf^gm\ZiZ\bmrh_Zlbgèrk^bg_hk\^]l^\mbhg!Z[ho^pab\a\hfik^llbhgk^bg_hk\^f^gmblk^jnbk^]"

F)%>ji

?bklmhk]^k[^g]bg`fhf^gmbgjnZlbi^kfZg^gmehZ]\hf[bgZmbhg!LEL"

F)*%F)+

?bklmhk]^k^g]fhf^gmlZmNELbg\en]bg`ZeehpZg\^l_hkbfi^k_^\mbhgl

F)>]

>jnboZe^gm_bklmhk]^kfhf^gmbg\en]bg`ma^^__^\mh_bfi^k_^\mbhgl!ZmZ[hnmfb]a^bàm"

F)>]%_b

?bklmhk]^kfhf^gmng]^k_bk^\hg]bmbhgl

F+

GhfbgZel^\hg]hk]^kfhf^gmbgle^g]^k\henfgl

F>]

=^lb`goZen^h_ma^Ziieb^]bgm^kgZe[^g]bg`fhf^gm

F>]r%F>]s

=^lb`gfhf^gmbgma^k^li^\mbo^]bk^\mbhg

FK]r%FK]s

Fhf^gmk^lblmZg\^bgma^k^li^\mbo^]bk^\mbhg

Fm

=^lb`gmkZgl_^kfhf^gmmh\henfg_khfZ_eZmleZ[

f

Gnf[^kh_o^kmb\Zef^f[^kl\hgmkb[nmbg`mhZg^__^\m

f

FZll

G

:qbZe_hk\^

G

;Zlb\liZg&mh&^__^\mbo^&]îmakZmbh%e(]%_hkD6*')

G)>]%_b

:qbZeehZ]ng]^k_bk^\hg]bmbhgl

G:

GZmbhgZe:gg^q

GZ%G[

Ehg`bmn]bgZe_hk\^l\hgmkb[nmbg`mhAb

G>]

=^lb`goZen^h_ma^Ziieb^]ZqbZe_hk\^!m^glbhghk\hfik^llbhg"ZmNEL

G=I

GZmbhgZeer=^m^kfbg^]IZkZf^m^k!l"Zlin[ebla^]bgZ\hngmkrÃlGZmbhgZe:gg^q

g

EhZ]eôêZmghkfZem^fi^kZmnk^l'
g

:qbZelmk^llZmNEL

g

NembfZm^Z\mbhg!ehZ]"i^kngbme^g`ma!hkZk^Z"

g

KêZmbo^ZqbZe_hk\^G>] (!:\ _\]"

g[Ze

MaôZen^h_gZmfZqbfnffhf^gmk^lblmZg\^

g)%gl

Gnf[^kh_lmhk^rl

Jd

Jd*!Jdb"

jd

j[

;Zlb\pbg]ik^llnk^

ji

I^Zdpbg]ik^llnk^

ji!s^"

I^Zdoêh\bmrik^llnk^Zmk^_^k^g\â^bàms^%!pbg]"

K

K^lblmZg\^4F^\aZgb\Zek^lblmZg\^!bg_bk^"

K:

K^Z\mbhgZmlniihkm:

K;

K^Z\mbhgZmlniihkm;

K]

=^lb`goZen^h_ma^k^lblmZg\^mhZgZ\mbhg

k

KZ]bnl

kf

KZmbhh__bklmhk]^k^g]fhf^gmlbg\henfglZmNEL

LEL

L ^kob\^Z[bebmrebfbmlmZm^!l"¾\hkk^lihg]bg`mh\hg]bmbhgl[^rhg]pab\ali^\b_b^]l^kob\^k^jnbk^f^gmlZk^gh ehg`^kf^m

l

LiZ\bg`

l

LghpehZ]hgZkhh_ v


Symbol

Definition

ld

lk

KZ]bZeliZ\bg`h_i^kbf^m^klh_la^Zkk^bg_hk\^f^gm

lm

MZg`^gmbZeliZ\bg`la^Zkk^bg_hk\^f^gmZehgì^kbf^m^klh_la^Zkk^bg_hk\^f^gm

m

Mab\dg^ll4Mbf^[^bg`\hglb]^k^]4;k^Z]mah_lniihkm

m)

Ma^Z`^h_\hg\k^m^Zmma^mbf^h_ehZ]bg`

NEL

NembfZmêbfbmlmZm^!l"¾Zllh\bZm^]pbma\heeZil^hkhma^k_hkflh_lmkn\mnkZe_Zbenk^

n

I^kbf^m^kh_\hg\k^m^\khll&l^\mbhg%aZobg`Zk^Z:\

n

I^kbf^m^kh_maZmiZkmpab\abl^qihl^]mh]krbg`

n

n)

I^kbf^m^kZ]cZ\^gmmh\henfgl!ing\abg`la^Zk"

n*

;Zlb\\hgmkhei^kbf^m^k!Zm+]_khf_Z\^h_ehZ]"!ing\abg`la^Zk"

n*#

K^]n\^]\hgmkhei^kbf^m^kZmi^kbf^m^k\henfgl!Zm+]_khf_Z\^h_ehZ]"!ing\abg`la^Zk"

nb

E^g`mah_ma^\hgmkhei^kbf^m^kng]^k\hglb]^kZmbhg!ing\abg`la^Zk"

nhnm

I^kbf^m^kZmpab\ala^Zkk^bg_hk\^f^gmblghehg`^kk^jnbk^]

O

La^Zk_hk\^

O>]

=^lb`goZen^h_ma^Ziieb^]la^Zk_hk\^

OK]%\

La^Zkk^lblmZg\^h_Zf^f[^kpbmahnmla^Zkk^bg_hk\^f^gm

OK]%fZq

La^Zkk^lblmZg\^h_Zf^f[^kebfbm^][rma^\knlabg`h_\hfik^llbhglmknml

OK]%\fbg

Fbgbfnfla^Zkk^lblmZg\^h_f^f[^k\hglb]^kbg`\hg\k^m^Zehg^

OK]%l

La^Zkk^lblmZg\^h_Zf^f[^k`ho^kg^][rma^rbê]bg`h_la^Zkk^bg_hk\^f^gm

o[

;Zlb\pbg]oêh\bmr

o[%)

M a^_ng]Zf^gmZe[Zlb\pbg]oêh\bmr[^bg`ma^\aZkZ\m^kblmb\*)fbgnm^pbg]oêh\bmrZm*)fZ[ho^`khng]eôêbg hi^g\hngmkr

o[%fZi

?ng]Zf^gmZe[Zlb\pbg]oêh\bmr_khf?b`nk^G:'*f(l

o>]

Ing\abg`la^Zklmk^ll

o>]

La^Zklmk^ll_hkl^\mbhglpbmahnmla^Zkk^bg_hk\^f^gm!6O>] ([p]"

o>]%s

La^Zklmk^ll_hkl^\mbhglpbmala^Zkk^bg_hk\^f^gm!6O>] ([ps6O>] ([p)'2]"

oK]%\

=^lb`gla^Zkk^lblmZg\^h_\hg\k^m^pbmahnmla^Zkk^bg_hk\^f^gm^qik^ll^]ZlZlmk^ll

oK]%fZq

P*

?Z\mhk\hkk^lihg]bg`mhZ]blmkb[nmbhgh_la^Zk!ing\abg`la^Zk"

P^

I^Zd^qm^kgZepbg]ehZ]

Pd

aZkZ\m^kblmb\oZen^h_pbg]Z\mbhg!G;ghmbgma^>nkh\h]^lZg]lahne][^k^`Zk]^]ZlZ_hkfh_Jd% < \aZkZ\m^kblmb\oZen^h_ZoZkbZ[e^Z\mbhg"

pd

pd

pfZq

Ebfbmbg`\Ze\neZm^]\kZ\dpb]ma

Q)%Q:%Q<
G^nmkZeZqbl]îma

q

=blmZg\^[^mp^^g[nbe]bg`l!pbg]"

q

=blmZg\^h_ma^l^\mbhg[^bg`\hglb]^k^]_khfma^\^gmkêbg^h_ma^lniihkm

q%r%s

qn

=îmah_ma^g^nmkZeZqblZmma^nembfZmêbfbmlmZm^Z_m^kk^]blmkb[nmbhg

S

Shg^gnf[^kh[mZbg^]_khffZi!lghp"

s

Eô^kZkfh_bgm^kgZe_hk\^l

vi


Symbol

Definition

s

K^_^k^g\â^bàm!pbg]"

s^

K^_^k^g\â^bàm_hkpbg]pZk]pZeelh_k^\mZg`neZk[nbe]bg`l!pbg]"

a

:gè^4:gè^h_la^Zkebgdlmhmaêhg`bmn]bgZeZqbl4KZmbh

a:

:\h^__b\b^gm_hknl^pbmaZkîk^l^gmZmboôZkbZ[e^Z\mbhgmZdbg`bgmhZ\\hngmZk^Zlniihkm^]

a*%a+%a, a-%a.%a/

?Z\mhkl]^Zebg`pbmaZg\ahkZ`^Zg]eZilh_[Zkl

a\\!a\m"

:\h^__b\b^gmmZdbg`bgmhZ\\hngmehg`m^kf^__^\mlh_\hfik^llbo^!m^glbe^"ehZ]Zg]ma^pZrehZ]blZiieb^]

a^

Fh]neZkkZmbh6>l (>\]

ag

:\h^__b\b^gm_hknl^pbmaZkîk^l^gmZmboôZkbZ[e^Z\mbhgmZdbg`bgmhZ\\hngmgnf[^kh_lmhk^rllniihkm^]

b

:gè^4KZmbh4
b

?Z\mhk]^Zebg`pbma^\\^gmkb\bmr!ing\abg`la^Zk"

g

IZkmbZe_Z\mhk

g<

IZkmbZe_Z\mhk_hk\hg\k^m^

g?

IZkmbZe_Z\mhk_hkZ\mbhgl%?

g@

IZkmbZe_Z\mhk_hki^kfZg^gmZ\mbhgl%@

g@d%lni

IZkmbZe_Z\mhkmh[^Ziieb^]mh@d%bg_

g@d%bg_

IZkmbZe_Z\mhkmh[^Ziieb^]mh@d%lni

gJ

IZkmbZe_Z\mhk_hkoZkbZ[e^Z\mbhgl%J

gF

IZkmbZe_Z\mhk_hkfZm^kbZe!nlnZeerg<hkgL"

gL

IZkmbZe_Z\mhk_hkk^bg_hk\bg`lm^ê

d

K^]blmkb[nmbhgkZmbh^jnZelkZmbhh_ma^k^]blmkb[nm^]fhf^gmmhma^êZlmb\[^g]bg`fhf^gm!*¾k^]blmkb[nmbhg"

e\n

NembfZm^\hfik^llbo^lmkZbgbgma^\hg\k^m^

e\n+

NembfZm^\hfik^llbo^lmkZbgebfbmbg\hg\k^m^pab\ablghm_neerbgink^ZqbZe\hfik^llbhgZllnfbg`nl^h_ma^ iZkZ[heb\¾k^\mZg`neZklmk^ll¾lmkZbgkêZmbhglabi!gnf^kb\Zeere\n+6e\n,"

e\n,

embfZm^\hfik^llbo^lmkZbgebfbmbg\hg\k^m^pab\ablghm_neerbgink^ZqbZe\hfik^llbhgZllnfbg`nl^h_ma^ N [bebg^Zklmk^ll¾lmkZbgkêZmbhglabi

el\

elm

M^glbe^lmkZbgbgk^bg_hk\^f^gm

n

?Z\mhk]^_bgbg`^__^\mbo^lmk^g`ma!6*_hk©<.)(/)"

n*

n+

y

:gè^4:gè^h_\hfik^llbhglmknml!la^Zk"

yb

Bg\ebgZmbhgnl^]mhkîk^l^gmbfi^k_^\mbhgl

l

Le^g]^kg^llkZmbh

l

?Z\mhk]^_bgbg`maâ^bàmh_ma^\hfik^llbhgshg^!6)'1_hk©<.)(/)"

l_b

Le^g]^kg^llbg_bk^

lebf

Ebfbmbg`le^g]^kg^llkZmbh!h_\henfgl"

mb%m*%m+

LghpehZ]laZi^_Z\mhkl

m_b

Zmbhh_ma^]^lb`gZqbZeehZ]ng]^k_bk^\hg]bmbhglmhma^]^lb`gk^lblmZg\^h_ma^\henfgZmghkfZem^fi^kZmnk^ K [nmpbmaZg^\\^gmkb\bmrZiieb\Z[e^mh_bk^\hg]bmbhgl

v

Lmk^g`mak^]n\mbhg_Z\mhk_hk\hg\k^m^\kZ\d^]bgla^Zk

j

K^]n\mbhg_Z\mhk(]blmkb[nmbhg\h^__b\b^gm'?Z\mhkZiieb^]mh@dbg;L>G*22)>qi'!/'*)["

r

K^jnbk^]m^glbhgk^bg_hk\^f^gmkZmbh

r

=^glbmrh_Zbk!pbg]"

r

K^bg_hk\^f^gmkZmbh_hkk^jnbk^]\hfik^llbhgk^bg_hk\^f^gm%:l+([]

vii


Symbol

Definition

r*

I^k\^gmZ`^h_k^bg_hk\^f^gmeZii^]pbmabg)'/.e)_khfma^\^gmkêbg^h_maêZi[^bg`\hglb]^k^]

re

K^bg_hk\^f^gmkZmbh_hkehg`bmn]bgZek^bg_hk\^f^gm

rer%res

K^bg_hk\^f^gmkZmbhh_[hg]^]lm^êbgma^rZg]s]bk^\mbhg

r)

K^_^k^g\^k^bg_hk\^f^gmkZmbh_\d)'.£*)¾,

s`]

=^lb`goZen^h_ma^`khng]ik^llnk^

sl

Lmk^llbgk^bg_hk\^f^gmZmLEL

sl

:[lhenmôZen^h_ma^fZqbfnflmk^lli^kfbmm^]bgma^k^bg_hk\^f^gmbff^]bZmêrZ_m^kma^_hkfZmbhgh_ma^\kZ\d

sl\!slm"

Lmk^llbg\hfik^llbhg!Zg]m^glbhg"k^bg_hk\^f^gm

sl]

=^lb`glmk^llbgma^[ZkZmma^nembfZmêbfbmlmZm^

sln

Ngfh]b_b^]l^kob\^lmk^llbgk^bg_hk\^f^gm]^m^kfbg^]_khfNELehZ]l!L^^?b`nk^<,"

h!e%m)"

?bgZeoZen^h_\k^î\h^__b\b^gm

h^_

>__^\mbo^\k^î_Z\mhk

f

;Zk]bZf^m^k

c

?Z\mhkl]^_bgbg`kîk^l^gmZmboôZen^lh_oZkbZ[e^Z\mbhgl

c)

c*

?k^jn^gmoZen^h_ZoZkbZ[e^Z\mbhg!^'`'nl^]pa^g\hglb]^kbg`pa^ma^kl^\mbhgpbeeaZo^\kZ\d^]hkghm"

c+

JnZlb&i^kfZg^gmoZen^h_ZoZkbZ[e^Z\mbhg!^'`'nl^]pa^g\hglb]^kbg`]^_hkfZmbhg"

w

F^\aZgb\Zek^bg_hk\^f^gmkZmbh6:l_r] (:\_\]©*

viii

Bgmkh]n\mbhg

* Introduction *'* Aim Ma^Zbfh_mablin[eb\ZmbhgblmhbeenlmkZm^makhnàphkd^]^qZfie^lahp;L>G*22+¾*¾*T*V !>nkh\h]^+"fZr[^nl^]bgikZ\mb\^mh]^lb`gbg&lbmn\hg\k^m^[nbe]bg`lmkn\mnk^l'Bmblbgm^g]^] maZm ma^l^ phkd^] ^qZfie^l pbee ^qieZbg ahp \Ze\neZmbhgl mh >nkh\h]^ + fZr [^ i^k_hkf^]' >nkh\h]^+lmkb\mer\hglblmlh__hnkiZkml!IZkml*¾*%*¾+%+Zg],"T*&-V[nm_hkmaînkihl^lh_ mablin[eb\Zmbhg%>nkh\h]^+k^_^klmhiZkm*¾*hger%nge^lljnZebË^]'Ma^phkd^]^qZfie^lpbee [^\Zkkb^]hnmpbmabgma^^gobkhgf^gmh_hma^kkêôZgmin[eb\Zmbhgleblm^][êhp%Zg]beenlmkZm^] bg?b`nk^*'*3


N Ma^hma^kmak^îZkmlh_>nkh\h]^+' N Hma^k>nkh\h]^l' N FZm^kbZeZg]^q^\nmbhglmZg]Zk]l' N In[eb\Zmbhgl[rma^\hg\k^m^bg]nlmkrZg]hma^kl'

Ma^k^ Zk^% ma^k^_hk^% fZgr k^_^k^g\^l mh hma^k ]h\nf^gml Zg] pabe^ bm bl bgm^g]^] maZm mabl in[eb\Zmbhg%k^_^kk^]mhZlPhkd^]^qZfie^l%\ZglmZg]Zehg^%bmblZgmb\biZm^]maZmnl^klfZr k^jnbk^ lô^kZe h_ ma^ hma^k k^_^k^g\^l mh aZg]% bg iZkmb\neZk% nkh\h]^ +T.V% pab\a lnffZkbl^l ma^ kne^l Zg] ikbg\bie^l maZm pbee [^ \hffhger nl^] bg ma^ ]^lb`g h_ k^bg_hk\^] \hg\k^m^_kZf^][nbe]bg`lmh>nkh\h]^+'

WORKED EXAMPLES

STANDARDS

CONCRETE INDUSTRY PUBLICATIONS

PUBLICATIONS BY OTHERS

NA CONCISE EUROCODE 2

BS EN 1990 BASIS OF DESIGN

MANUALS

VOL 2 NA BS EN 1991–2 NA BS EN 1991–1–1 –2 NA NA –3 NA ACTIONS –4 NA –6

WORKED EXAMPLES TO EUROCODE 2 VOL 1

HOW TO DESIGN CONCRETE STRUCTURES DETAILERS HANDBOOK

Densities and imposed loads Fire Snow Wind Execution

www. Eurocode2 .info DESIGN GUIDES

PD6687 NA

NA BS EN 1992–1–1 1–2 NA NA DESIGN OF –2 CONCRETE –3 STRUCTURES General Fire Bridges Liquid retaining

RC SPREAD SHEETS

BS EN 13670 EXECUTION OF CONCRETE STRUCTURES

PRECAST DESIGN MANUAL

PRECAST WORKED EXAMPLES

Ghm^ Ma^m^kfLmZg]Zk]l^g\hfiZll^l;kbmblaLmZg]Zk]l%>nkh\h]^l%GZmbhgZe:gg^q^l!G:"Zg]In[ebla^]=h\nf^gml ?b`nk^*'* Phkd^]^qZfie^lbg\hgm^qm

Ma^]^lb`glZk^bgZ\\hk]Zg\^pbma;L>G*22+¾*¾*T*V%Zlfh]bË^][rma^NDGZmbhgZe:gg^qT*ZV Zg]^qieZbg^]bgI=//10T/V' 1

@^g^kZeer% ma^ \Ze\neZmbhgl Zk^ \khll&k^_^k^g\^] mh ma^ kêôZgm \eZnl^l bg Zee _hnk iZkml h_ >nkh\h]^ +T*¾-V Zg]% pa^k^ ZiikhikbZm^% mh hma^k ]h\nf^gml' L^^ ?b`nk^ *'+ _hk Z `nb]^ mh ik^l^gmZmbhg'K^_^k^g\^lmh;L1**)T0Vk^_^kmhIZkm*nge^llhma^kpbl^lmZm^]'


@^g^kZeer%ma^Âlbfie^Ã^qZfie^l]î^g]hg^jnZmbhglZg]]^lb`gZb]l]^kbo^]_khf>nkh\h]^+' Ma^]^kbo^]^jnZmbhglZk^`bo^gbg:ii^g]bq:Zg]ma^]^lb`gZb]l_khfL^\mbhg*.h_nkh\h]^+T.VZk^kî^Zm^]bg:ii^g]bq;' Ma^^qZfie^lZk^bgm^g]^]mh[^ZiikhikbZm^_hkma^bkinkihl^%pab\ablmhbeenlmkZm^ma^nl^h_ >nkh\h]^+_hkbg&lbmn\hg\k^m^[nbe]bg`lmkn\mnk^l'Ma^k^Zk^lbfie^^qZfie^lmhbeenlmkZmâhp mrib\ZeaZg]\Ze\neZmbhglfbàm[^]hg^nlbg`ZoZbeZ[e^\aZkmlZg]mZ[e^l]^kbo^]_khfma^nkh\h]^+%lô^kZeh_ma^\Ze\neZmbhglZkîk^l^gm^]bg]^mZbe_Zk bg^q\^llh_maZmg^\^llZkrbg]^lb`g\Ze\neZmbhglhg\^nl^klZk^_ZfbebZkpbmama^
Worked examples

Cl. 6.4.4

KêôZgm\eZnl^lhk_b`nk^gnf[^kl_khf;L>G *22+¾*¾*!b_ma^k^_^k^g\^blmhhma^kiZkml%hma^k >nkh\h]^lhkhma^k]h\nf^gmlmablpbee[^bg]b\Zm^]"

Cl. 6.4.4

NA

?khfma^kêôZgmNDGZmbhgZe:gg^q!`^g^kZeermh ;L>G*22+¾*¾*"

NA

Cl. 6.4.4 & NA

?khf[hma;L>G*22+¾*¾*Zg]NDGZmbhgZe:gg^q

Cl. 6.4.4 & NA

Fig. 2.1 Section 5.2

KêôZgmiZkmlh_mablin[eb\Zmbhg

Fig. 2.1 Section 5.2

EC1-1-1: 6.4.3

?khfhma^k>nkh\h]^l3;L>G*22)%;L>G*22*% ;L>G*22+¾*¾+%^m\

EC1-1-1: 6.4.3

PD 6687[6]

;Z\d`khng]iZi^kmhNDGZmbhgZe:gg^q^l ;L>G*22+¾*

PD 6687[6]

Concise

nkh\h]^+T.V

Concise

How to: Floors [8]

Ahpmh]^lb`g\hg\k^m^lmkn\mnk^lnlbg` >nkh\h]^+T1V3?ehhkl

How to: Floors[8]

Grey shaded tables

Bg:ii^g]b\^l%]^kbo^]\hgm^gmbgmZ[e^lghm_khf >nkh\h]^+

?b`nk^*'+ @nb]^mhik^l^gmZmbhg

:llhf^h_ma^]^mZbebg`kne^lbg>nkh\h]^+Zk^`^g^kZeerfhk^bgoheo^]maZgmahl^mh;L1**)% lhf^ h_ ma^ ]^lb`gl ik^l^gm^] bg mabl in[eb\Zmbhg aZo^ [^^g ^qm^g]^] bgmh Zk^Zl maZm aZo^ mkZ]bmbhgZeer[^^gma^k^lihglb[bebmrh_]^mZbe^kl'Ma^l^^qm^g]^]\Ze\neZmbhglZk^ghmg^\^llZkber iZkm h_ÂghkfZeÃ ]^lb`g [nm Zk^ bg\en]^] Zm ma^ ^g] h_ lhf^ \Ze\neZmbhgl' Bm bl Zllnf^] maZm ma^]^lb`g^kpbee]bl\nllZg]Z`k^^pbmama^]^mZbe^kZk^Zlh_k^lihglb[bebmrZg]ma^]^`k^^h_ kZmbhgZeblZmbhg% ma^ ^qm^gm h_ ]^lb`gbg` ]^mZbel% Zll^llf^gm h_ \nkmZbef^gm Zg] hma^k Zli^\ml maZmma^]^mZbe^klahne]ng]^kmZd^'Bmblk^\h`gbl^]maZmbgmaôZlmfZchkbmrh_\Zl^l%ma^kne^l `bo^gbg]^mZbebg`fZgnZelT1%2Vpbee[^nl^]'Ahpô^k%ma^^qZfie^lZk^bgm^g]^]mhaêipa^g \nkmZbef^gm%Zg\ahkZ`^Zg]eZie^g`malg^^]mh[^]^m^kfbg^]'

2

Bgmkh]n\mbhg *'+ Eurocode: Basis of structural design


Bg ma^ >nkh\h]^ lrlm^f ;L >G *22)% >nkh\h]^3 ;Zlbl h_ lmkn\mnkZe ]^lb`gT*)V ho^kZk\a^l Zee ma^ hma^k>nkh\h]^l%;L>G*22*mh;L>G*222';L>G*22)]^Ëg^lma^^__^\mlh_Z\mbhgl%bg\en]bg` `^hm^\agb\Ze Zg] l^blfb\ Z\mbhgl% Zg] Ziieb^l mh Zee lmkn\mnk^l bkk^li^\mbo^ h_ ma^ fZm^kbZe h_ \hglmkn\mbhg'Ma^fZm^kbZe>nkh\h]^l]^Ëgâhpma^^__^\mlh_Z\mbhglZk^k^lblm^][r`bobg`kne^l_hk ]^lb`gZg]]^mZbebg`h_\hg\k^m^%lm^ê%\hfihlbm^%mbf[^k%fZlhgkrZg]Zenfbgbnf'!l^^?b`nk^*',"' BS EN 1990, Eurocode: Basis of structural design

Structural safety, serviceability and durability

BS EN 1991, Eurocode 1: Actions on structures

Actions on structures

BS EN 1992, Eurocode 2: Concrete BS EN 1993, Eurocode 3: Steel BS EN 1994, Eurocode 4: Composite BS EN 1995, Eurocode 5: Timber BS EN 1996, Eurocode 6: Masonry BS EN 1999, Eurocode 9: Aluminium BS EN 1997, Eurocode 7: Geotechnical design

Design and detailing

BS EN 1998, Eurocode 8: Seismic design

Geotechnical and seismic design

?b`nk^*', Ma^>nkh\h]âb^kZk\ar

;L>G*22)ikhob]^lma^g^\^llZkrbg_hkfZmbhg_hkma^ZgZerlblh_lmkn\mnk^lbg\en]bgìZkmbZe Zg]hma^k_Z\mhklmh[^Ziieb^]mhma^Z\mbhgl_khf>nkh\h]^*'Bm^lmZ[ebla^lmaîkbg\bie^lZg] k^jnbk^f^gml_hkma^lZ_^mr%l^kob\^Z[bebmrZg]]nkZ[bebmrh_lmkn\mnk^l'Bm]^l\kb[^lma^[Zlbl_hk ]^lb`gZl_heehpl3

EC0: 2.1

:lmkn\mnk^laZee[^]^lb`g^]Zg]^q^\nm^]!\hglmkn\m^]"bgln\aZpZrmaZmbmpbee%]nkbg`bml bgm^g]^]eb_^%pbmaZiikhikbZm^]^`k^^lh_kêbZ[bebmrZg]bgZg^\hghfb\ZepZr3 N LnlmZbgZeeZ\mbhglZg]bg_en^g\^lebdêrmhh\\nk]nkbg`^q^\nmbhgZg]nl^' N K^fZbg_bm_hkma^nl^_hkpab\abmblk^jnbk^]'

Bghma^kphk]l%bmlaZee[^]^lb`g^]nlbgèbfbmlmZm^likbg\bie^lmhaZo^Z]^jnZm^3 N LmZ[bebmr' N Lmkn\mnkZek^lblmZg\^!bg\en]bg`lmkn\mnkZek^lblmZg\^bg_bk^"' N L^kob\^Z[bebmr' N =nkZ[bebmr'

?hk[nbe]bg`lmkn\mnk^l%Z]^lb`gphkdbgèb_^h_.)r^Zklblbfieb^]' ;L>G*22)lmZm^lmaZmebfbmlmZm^llahne][ô^kbË^]bgZeekêôZgm]^lb`glbmnZmbhgl3i^klblm^gm% mkZglb^gmhkZ\\b]^gmZe'GhkêôZgmebfbmlmZm^laZee[^^q\^^]^]pa^g]^lb`goZen^l_hkZ\mbhgl Zg]k^lblmZg\^lZk^nl^]bg]^lb`g'MaêbfbmlmZm^lZk^3 N NembfZmêbfbmlmZm^l!NEL"%pab\aZk^Zllh\bZm^]pbma\heeZil^hkhma^k_hkflh_lmkn\mnkZe

_Zbenk^' N L^kob\^Z[bebmrebfbmlmZm^l!LEL"%pab\a\hkk^lihg]mh\hg]bmbhgl[^rhg]pab\ali^\b_b^]

l^kob\^k^jnbk^f^gmlZk^ghehg`^kf^m' :eeZ\mbhglZk^Zllnf^]mhoZkrbgmbf^Zg]liZ\^'LmZmblmb\Zeikbg\bie^lZk^Ziieb^]mhZkkbo^Zmma^ fZ`gbmn]^h_maîZkmbZeehZ]_Z\mhklmh[^nl^]bg]^lb`gmhZ\abô^ma^k^jnbk^]kêbZ[bebmrbg]^q !eôêh_lZ_^mr"'Ma^k^blZgng]^kerbg`ZllnfimbhgmaZmma^Z\mbhglma^flêo^lZk^]^l\kb[^]bg lmZmblmb\Zem^kfl' 3

*', Eurocode 1: Actions on structures


:\mbhglZk^]^Ëg^]bgma^*)iZkmlh_;L>G*22*>nkh\h]^*3:\mbhglhglmkn\mnk^lT**V3 ;L>G*22*¾*¾*3+))+3=^glbmb^l%lê_&p^bàm%bfihl^]ehZ]l_hk[nbe]bg`l ;L>G*22*¾*¾+3+))+3:\mbhglhglmkn\mnk^l^qihl^]mhËk^ ;L>G*22*¾*¾,3+)),3LghpehZ]l ;L>G*22*¾*¾-3+)).3Pbg]Z\mbhgl ;L>G*22*¾*¾.3+)),3Ma^kfZeZ\mbhgl ;L>G*22*¾*¾/3+)).3:\mbhgl]nkbg`^q^\nmbhg ;L>G*22*¾*¾03+))/3:\\b]^gmZeZ\mbhgl ;L>G*22*¾+3+)),3:\mbhglhglmkn\mnk^l'MkZ_Ë\ehZ]lhg[kb]`^l ;L>G*22*¾,3+))/3G*22*¾-3+))/3LbehlZg]mZgdl Mabl in[eb\Zmbhg bl fZbger \hg\^kg^] pbma ]^lb`gbg` _hk ma^ Z\mbhgl ]^Ëg^] [r IZkm¾*¾*3 =^glbmb^l%lê_&p^bàm%bfihl^]ehZ]l_hk[nbe]bg`l' =^lb`goZen^lh_Z\mbhglZg]ehZ]ZkkZg`^f^gmlZk^\ho^k^]bgL^\mbhg+'

*'- Eurocode 2: Design of concrete structures >nkh\h]^+3=^lb`gh_\hg\k^m^lmkn\mnk^lT*¾-Vhi^kZm^lpbmabgZg^gobkhgf^gmh_hma^k>nkhi^Zg Zg];kbmblalmZg]Zk]l!l^^?b`nk^*',"'Bmbl`ho^kg^][r;L>G*22)T*)VZg]ln[c^\mmhma^Z\mbhgl ]^Ëg^]bg>nkh\h]^l*T**V%0T*+VZg]1T*,V'Bm]î^g]lhgoZkbhnlfZm^kbZelZg]^q^\nmbhglmZg]Zk]l Zg] bl nl^] Zl ma^ [Zlbl h_ hma^k lmZg]Zk]l' IZkm +% ;kb]`^lT,V% Zg] IZkm ,% Ebjnb]k^mZbgbg`Zg] \hgmZbgf^gmlmkn\mnk^lT-V%phkd[r^q\îmbhgmhIZkm*¾*Zg]*¾+%maZmbl%\eZnl^lbgIZkml+Zg], \hgËkf%fh]b_rhkkîeZ\^\eZnl^lbgIZkm*¾*'

BS EN 1990 EUROCODE Basis of Structural Design BS EN 1997 EUROCODE 7 Geotechnical Design

BS EN 1998 EUROCODE 8 Seismic Design BS EN 1991 EUROCODE 1 Basis of Structural Design

BS 4449 Reinforcing Steels

BS 8500 Specifying Concrete

BS EN 206 Concrete

BS EN 13670 Execution of Structures

BS EN 1995 EUROCODE 5 Design of Composite Structures

BS EN 1992 EUROCODE 2 Design of concrete structures Part 1–1: General Rules for Structures Part 1–2: Structural Fire Design

BS EN 1992 EUROCODE 2 Part 2: Bridges

BS EN 1992 EUROCODE 2 Part 3: Liquid Retaining Structures

Ghm^ ?hk\eZkbmrGZmbhgZe:gg^q^lZg]^qieZgZmhkr]h\nf^gml!^'`'I=//10%Zg] Ghg&nkh\h]^+bg\hgm^qm

4

BS EN 10080 Reinforcing Steels

BS EN 13369 Precast Concrete

Bgmkh]n\mbhg *'. National Annexes Bmblmaîk^kh`Zmbo^h_^Z\a<>GF^f[^kLmZm^mh\hgmkheeôêlh_lZ_^mrbgmaZm\hngmkr':lZ k^lnem%lhf^lZ_^mr_Z\mhklZg]hma^kiZkZf^m^klbgma^>nkh\h]^l%ln\aZl\ebfZmb\\hg]bmbhgl% ]nkZ[bebmr\eZll^lZg]]^lb`gf^mah]l%Zk^ln[c^\mmh\hgËkfZmbhghklê^\mbhgZmZgZmbhgZeeôê' Ma^]^\blbhglfZ]^[rma^gZmbhgZe[h]b^l[^\hf^GZmbhgZeer=^m^kfbg^]IZkZf^m^kl!G=Il" pab\a Zk^ in[ebla^] bg Z GZmbhgZe:gg^q !G:" _hk ^Z\a iZkm h_ ^Z\a >nkh\h]^'Ma^ GZmbhgZe :gg^q fZr Zelh bg\en]^ k^_^k^g\^ mh ghg&\hgmkZ]b\mhkr \hfie^f^gmZkr bg_hkfZmbhg !G<

*'/ Basis of the worked examples in this publication

Ma^]^lb`g\Ze\neZmbhglbgmablin[eb\ZmbhgZk^bgZ\\hk]Zg\^pbma3 N ;L>G*22)%>nkh\h]^3;Zlblh_lmkn\mnkZe]^lb`gT*)VZg]bmlNDGZmbhgZe:gg^qT*)ZV' N ;L>G*22*%>nkh\h]^*3:\mbhglhglmkn\mnk^lbg*)iZkmlT**VZg]ma^bkNDGZmbhgZe

:gg^q^lT**ZV' N ;L>G*22+¾*¾*%>nkh\h]^+¾IZkm*¾*3=^lb`gh_\hg\k^m^lmkn\mnk^l¾@^g^kZekne^lZg]

kne^l_hk[nbe]bg`lT*VZg]bmlNDGZmbhgZe:gg^qT*ZV' N ;L>G*22+¾*¾+%>nkh\h]^+¾IZkm*¾+3=^lb`gh_\hg\k^m^lmkn\mnk^l¾@^g^kZekne^l¾

Lmkn\mnkZe_bk^]^lb`gT+VZg]bmlNDGZmbhgZe:gg^qT+ZV' N I=//10%;Z\d`khng]iZi^kmhma^NDGZmbhgZe:gg^q^lT/V' N ;L>G*220%>nkh\h]^03@^hm^\agb\Ze]^lb`g¾IZkm*'@^g^kZekne^lT*+VZg]bmlNDGZmbhgZe

:gg^qT*+ZV' Ma^rnl^fZm^kbZel\hg_hkfbg`mh3 N ;L1.))¾*3G+)/¾*3F^mah]h_li^\b_rbg`

Zg]`nb]Zg\^mhma^li^\b_b^kT*-V' N ;L---23Lm^ê_hkma^k^bg_hk\^f^gmh_\hg\k^m^¾Pê]Z[e^k^bg_hk\bg`lm^ê¾;Zk%\hbeZg]

]^\hbe^]ikh]n\m¾Li^\b_b\ZmbhgT*.V' Ma^rfZd^k^_^k^g\^mhlô^kZein[eb\Zmbhgl%fhlmghmZ[er3 N nkh\h]^+_hkma^]^lb`gh_bg&lbmn\hg\k^m^_kZf^][nbe]bg`lmh;L>G*22+¾*¾*3 +))-Zg]bmlNDGZmbhgZe:gg^q3+)).T.V' T1V' N Ahpmh]^lb`g\hg\k^m^lmkn\mnk^lnlbg`>nkh\h]^+

Ma^^q^\nmbhgh_ma^phkdlblZllnf^]mh\hg_hkfmh3 N I=//10;Z\d`khng]iZi^kmhma^NDGZmbhgZe:gg^q^l;L>G*22+¾*'T/V N GL
+))-' Hk%pa^gZoZbeZ[e^ N ;L>G*,/0)3>q^\nmbhgh_\hg\k^m^lmkn\mnk^l'=n^+)*)T*0V':lbfie^f^gm^][r

li^\b_b\Zmbhglln\aZl3 N GL
<
5

*'0 Assumptions *'0'* Eurocode 2 Cl. 1.3


PD 6687[6]

>nkh\h]^+Zllnf^lmaZm3 N =^lb`gZg]\hglmkn\mbhgpbee[^ng]^kmZd^g[rZiikhikbZmêrjnZeb_b^]Zg]^qi^kb^g\^]i^klhggê' N :]^jnZm^lni^koblbhgZg]jnZebmr\hgmkhepbee[îkhob]^]' N FZm^kbZelZg]ikh]n\mlpbee[^nl^]Zlli^\b_b^]' N Ma^lmkn\mnk^pbee[^Z]^jnZmêrfZbgmZbg^]Zg]pbee[^nl^]bgZ\\hk]Zg\^pbmama^]^lb`g[kb^_' N Ma^k^jnbk^f^gml_hk^q^\nmbhgZg]phkdfZglabi`bo^gbg>G*,/0)Zk^\hfieb^]pbma' *'0'+ The worked examples Nge^llghm^]hma^kpbl^%ma^\Ze\neZmbhglbgmablin[eb\ZmbhgZllnf^3

EC0: Table 2.1

N :]^lb`geb_^h_.)r^Zkl'

Table 3.1

N Ma^nl^h_<,)(,0\hg\k^m^'

BS 4449

N Ma^nl^h_@kZ]^:%;hk<k^bg_hk\^f^gm%]^lb`gZm^]ÂAÃbgZ\\hk]Zg\^pbma;L1///T*2V'

Table 4.1, BS 8500: Table A.1

N >qihlnk^\eZllQ<*'

Building Regs[20,21]

N *ahnk_bk^k^lblmZg\^'

@^g^kZeer^Z\a\Ze\neZmbhgblkhng]^]Zg]bmblma^khng]^]oZen^maZmblnl^]bgZgr_nkma^k\Ze\neZmbhg'

*'1 Material properties FZm^kbZeikhi^kmb^lZk^li^\bË^]bgm^kflh_ma^bk\aZkZ\m^kblmb\oZen^l'MablnlnZeer\hkk^lihg]l mhmaêhp^k._kZ\mbe^h_ZgZllnf^]lmZmblmb\Ze]blmkb[nmbhgh_maîkhi^kmr\hglb]^k^]' MaôZen^lh_g<Zg]gL%iZkmbZe_Z\mhkl_hkfZm^kbZel%Zk^bg]b\Zm^]bgMZ[e^*'*' Table 2.1 & NA

MZ[e^*'* IZkmbZe_Z\mhkl_hkfZm^kbZel =^lb`glbmnZmbhg

g<¾\hg\k^m^

gL¾k^bg_hk\bg`lm^ê

ULS – persistent and transient

*'.)

*'*.

Accidental – non-fire

*'+)

*'))

Accidental – fire

*'))

*'))

SLS

*'))

*'))

*'2 Execution Bgma^ND%==>GO*,/0)T++Vbl\nkk^gmerZoZbeZ[e^[nmpbmahnmbmlGZmbhgZe:iieb\Zmbhg=h\nf^gm' ?hk[nbe]bg`lmkn\mnk^lbgma^ND%ma^[Z\d`khng]]h\nf^gmI=//10T/V\hglb]^klmaîkhoblbhglh_ ma^GZmbhgZeLmkn\mnkZeG*,/0)_hk mhe^kZg\^\eZll*'Pa^gin[ebla^]%;L>G*,/0)T*0VZg]%b_ZiikhikbZm^%ma^\hkk^lihg]bg`GZmbhgZe :iieb\Zmbhg=h\nf^gmpbeemZdîk^\^]^g\^'

6


+ Analysis, actions and load arrangements +'* Methods of analysis +'*'* ULS :mma^nembfZmêbfbmlmZm^!NEL"ma^mri^h_ZgZerlbllahne][^ZiikhikbZm^mhmaîkh[e^f[^bg` \hglb]^k^]'Ma^_heehpbg`Zk^\hffhgernl^]3 N Ebg^ZkêZlmb\ZgZerlbl'

Cl. 5.1.1(7)

N Ebg^ZkêZlmb\ZgZerlblpbmaebfbm^]k^]blmkb[nmbhg'


N IeZlmb\ZgZerlbl'

?hk NEL% ma^ fhf^gml ]^kbo^] _khf êZlmb\ ZgZerlbl fZr [^ k^]blmkb[nm^] ikhob]^] maZm ma^ k^lnembg`]blmkb[nmbhgh_fhf^gmlk^fZbglbg^jnbeb[kbnfpbmama^Ziieb^]Z\mbhgl'Bg\hgmbgnhnl [^ZflhkleZ[lpbma_\d©.)FIZma^fbgbfnfZeehpZ[e^kZmbhh_ma^k^]blmkb[nm^]fhf^gmmh ma^fhf^gmbgmaêbg^ZkZgZerlbl%d%bl)'0)pa^k^
Cl. 5.5.4 & NA

Cl. 5.1.1

Cl. 5.6.2

+'*'+ SLS :mma^l^kob\^Z[bebmrebfbmlmZm^!LEL"ebg^ZkêZlmb\ZgZerlblfZr[^nl^]'Ebg^ZkêZlmb\ZgZerlbl fZr[^\Zkkb^]hnmZllnfbg`3 N
`khlll^\mbhgl"'

Cl. 5.4(1)

N Ebg^Zklmk^ll¾lmkZbgkêZmbhglabil' N Ma^nl^h_f^ZgoZen^lh_êZlmb\fh]nenl'

+'+ Actions

:\mbhglk^_^kmhehZ]lZiieb^]mhma^lmkn\mnk^Zl]^Ëg^][êhp3 N I^kfZg^gmZ\mbhglZk^Z\mbhgl_hkpab\amaôZkbZmbhgbgfZ`gbmn]^pbmambf^blg^èb`b[e^'

EC1-1-1: 2.1

N OZkbZ[e^Z\mbhglZk^Z\mbhgl_hkpab\amaôZkbZmbhgbgfZ`gbmn]^pbmambf^blghmg^èb`b[e^'

EC1-1-1: 2.2, 3.3.1(2)

N :\\b]^gmZeZ\mbhglZk^Z\mbhglh_lahkm]nkZmbhg[nmh_lb`gb_b\ZgmfZ`gbmn]^maZmZk^

ngebdêrmhh\\nkhgZ`bo^glmkn\mnk^]nkbg`ma^]^lb`gphkdbgèb_^' Bfihl^]]^_hkfZmbhglZk^ghm\hglb]^k^]bgmablin[eb\Zmbhg'

EC1-1-7

+', Characteristic values of actions

MaôZen^lh_Z\mbhgl`bo^gbgmaôZkbhnliZkmlh_>nkh\h]^*3:\mbhglhglmkn\mnk^lT**VZk^mZd^g Zl\aZkZ\m^kblmb\oZen^l'Ma^\aZkZ\m^kblmb\oZen^h_ZgZ\mbhgbl]^Ëg^][rhg^h_ma^_heehpbg` mak^^Zem^kgZmbo^l3 N Bmlf^ZgoZen^¾`^g^kZeernl^]_hki^kfZg^gmZ\mbhgl'

EC0: 4.1.2

7

N :gnii^koZen^pbmaZgbgm^g]^]ikh[Z[bebmrh_ghm[^bg`^q\^^]^]hkehp^koZen^pbmaZg

bgm^g]^]ikh[Z[bebmrh_[^bg`Z\abô^]¾ghkfZeernl^]_hkoZkbZ[e^Z\mbhglpbmadghpg lmZmblmb\Ze]blmkb[nmbhgl%ln\aZlpbg]hklghp' N :ghfbgZeoZen^¾nl^]_hklhfôZkbZ[e^Zg]Z\\b]^gmZeZ\mbhgl'

+'- Variable actions: imposed loads +'-'* General Bfihl^]ehZ]lhg[nbe]bg`lZk^]bob]^]bgmh\Zm^`hkb^l'Mahl^fhlm_k^jn^gmernl^]bg\hg\k^m^ ]^lb`gZk^lahpgbgMZ[e^+'*'


A B C D E F G H I K MZ[e^+'*
:k^Zl_hk]hf^lmb\Zg]k^lb]^gmbZeZ\mbobmb^l H__b\^Zk^Zl :k^Zlh_\hg`k^`Zmbhg Lahiibg`Zk^Zl LmhkZ`^Zk^ZlZg]bg]nlmkbZenl^!bg\en]bg`Z\\^llZk^Zl" MkZ__b\Zg]iZkdbg`Zk^Zl!oâb\e^l5,)dG" MkZ__b\Zg]iZkdbg`Zk^Zl!oâb\e^l7,)dG" Khh_l!bgZ\\^llb[e^^q\îm_hkfZbgm^gZg\^Zg]kîZbk" Khh_l!Z\\^llb[e^pbmah\\niZg\r\Zm^`hkb^l:¾=" Khh_l!Z\\^llb[e^_hkli^\bZel^kob\^l%^'`'_hkaêb\him^keZg]bg`Zk^Zl"

Ghm^l 1G*22*¾*¾*
+'-'+ Characteristic values of imposed loads
MZ[e^+'+ :3]hf^lmb\Zg]k^lb]^gmbZe Ln[& \Zm^`hkr

>qZfie^

Bfihl^]ehZ]l

A1

:eenlZ`^lpbmabglê_&\hgmZbg^]]pêebg`ngbml'
*'.

+')

A2

;^]khhflZg]]hkfbmhkb^l%^q\îmmahl^bglê_&\hgmZbg^] lbgè^_Zfber]pêebg`ngbmlZg]bgahmêlZg]fhmêl

*'.

+')

jd!dG(f+" Jd!dG"

A3

;^]khhflbgahmêlZg]fhmêl4ahlibmZepZk]l4mhbe^mZk^Zl

+')

+')

A4

;beebZk](lghhd^kkhhfl

+')

+'0

A5

;Ze\hgb^lbglbgè^&_Zfber]pêebg`ngbmlZg]\hffngZeZk^Zl bglfZeeZ[eh\dlh__eZml

+'.

+')

A6

;Ze\hgb^lbgahlmêl%`n^lmahnl^l%k^lb]^gmbZe\en[l'
Fbg',')[

Fbg'+')\

A7

;Ze\hgb^lbgahmêlZg]fhmêl

Fbg'-')[

Fbg'+')\

Ghm^l aLfZee[eh\dlh__eZmlZk^mahl^pbma©,lmhk^rlZg]©-_eZmli^k_ehhk(lmZbk\Zl^'Hma^kpbl^ma^rZk^ \hglb]^k^]mh[êZk`^k[eh\dlh__eZml bLZf^Zlma^khhflmhpab\ama^r`bo^Z\\^ll%[nmpbmaZfbgbfnfh_,')dG(f+hk-')dG(f+ c
EC1-1-1: Tables 6.1, 6.2 & NA.3

8

MZ[e^+', ;3h__b\^l Ln[& \Zm^`hkr

>qZfie^

Bfihl^]ehZ]l

B1

@^g^kZenl^hma^kmaZgbg;+

+'.

+'0

B2

:mhk[êhp`khng]_ehhkeôê

,')

+'0

jd!dG(f+" Jd!dG"



MZ[e^+'- <3Zk^Zlh_\hg`k^`Zmbhg

EC1-1-1: Tables 6.1, 6.2 & NA.3

Ln[& \Zm^`hkr

>qZfie^

Bfihl^]ehZ]l

<*

:k^ZlpbmamZ[e^l

C11

In[eb\%bglmbmnmbhgZeZg]\hffngZe]bgbg`khhflZg] ehng`^l%\Z_^lZg]k^lmZnkZgml!Ghm^3nl^<-hk<.b_ ZiikhikbZm^"

C12

K^Z]bg`khhflpbmagh[hhdlmhkZ`^

+'.

-')

C13

,')

,')

<+

:k^Zlpbma_bq^]l^Zml

C21

:ll^f[erZk^Zlpbma_bq^]l^Zmbgà

-')

,'/

C22

IeZ\^lh_phklabi

,')

+'0

<,

:k^Zlpbmahnmh[lmZ\e^l_hkfhobgì^hie^

C31

,')

-'.

C32

LmZbkl%eZg]bg`lbgbglmbmnmbhgZemri^[nbe]bg`l%ahlmêl% `n^lmahnl^l%k^lb]^gmbZe\en[lZg]\hffngZeZk^Zlbg eZk`^kb[eh\dlh__eZml

,')

-')

C33

-')

-'.

C34

.')

-'.

C35

LmZbkl%eZg]bg`lbghma^kc[nbe]bg`lln[c^\m^]mh\khp]l

-')

-')

C36

PZedpZrl¾Ebàm]nmr!Z\\^lllnbmZ[e^_hkhgî^klhg% pZedpZrpb]maZiikhq/))ff"

,')

+')

C37

PZedpZrl¾@^g^kZe]nmr!k^`neZkmph&pZri^]^lmkbZg mkZ__b\"

.')

,'/

C38

PZedpZrl¾A^Zor]nmr!abà&]^glbmri^]^lmkbZgmkZ__b\ bg\en]bg`^l\Zi^khnm^l"

0'.

-'.

C39

Fnl^nf_ehhklZg]Zkm`Zee^kb^l_hk^qab[bmbhginkihl^l

-')

-'.

<-

:k^Zlpbmaihllb[eîarlb\ZeZ\mbobmb^l

j d

Jd

+')

,')

C41

=Zg\âZeelZg]lmn]bhl%`rfgZlbZ%lmZ`^ld

.')

,'/

C42

=kbeeaZeelZg]]kbeekhhfld

.')

0')

<.

:k^Zlln[c^\m^]mheZk`^\khp]l

C51

:ll^f[erZk^Zlpbmahnm_bq^]l^Zmbg`%\hg\^kmaZeel%[Zkl Zg]ieZ\^lh_phklabid,e

.')

,'/

C52

LmZ`^lbgin[eb\Zll^f[erZk^Zld

0'.

-'.

D^r a?bq^]l^Zmbg`bll^Zmbg`pa^k^bmlk^fhoZeZg]ma^nl^h_ma^liZ\^_hkhma^kinkihl^lblbfikh[Z[e^

bLfZee[eh\dlh__eZmlZk^mahl^pbma©,lmhk^rlZg]©-_eZmli^k_ehhk(lmZbk\Zl^'Hma^kpbl^ma^rZk^ \hglb]^k^]mh[^ÂeZk`^kÃ[eh\dlh__eZml

cHma^k[nbe]bg`lbg\en]^mahl^ghm\ho^k^][r<,*Zg]<,+%Zg]bg\en]âhmêlZg]fhmêlZg] bglmbmnmbhgZe[nbe]bg`lln[c^\m^]mh\khp]l

d?hklmkn\mnk^lmaZmfbàm[^lnl\îmb[e^mhk^lhgZg\^^__^\ml%k^_^k^g\^lahne][^fZ]^mhG:'+'* e?hk`kZg]lmZg]lZg]lmZ]bZ%k^_^k^g\^lahne][^fZ]^mhma^k^jnbk^f^gmlh_ma^ZiikhikbZm^ \^kmb_rbg`Znmahkbmr

9

EC1-1-1: Tables 6.1, 6.2 & NA.3


EC1-1-1: Tables 6.3, 6.4 & NA.4, NA.5

MZ[e^+'. =3lahiibg`Zk^Zl Ln[& \Zm^`hkr

>qZfie^

Bfihl^]ehZ]l

=

Lahiibg`Zk^Zl

D1

:k^Zlbg`^g^kZek^mZbelahil

-')

,'/

D2

:k^Zlbg]îZkmf^gmlmhk^l

-')

,'/

jd!dG(f+"

Jd!dG"

MZ[e^+'/ >3lmhkZ`^Zk^ZlZg]bg]nlmkbZenl^!bg\en]bg`Z\\^llZk^Zl" Ln[& \Zm^`hkr

>qZfie^

Bfihl^]ehZ]l

>*

:k^Zllnl\îmb[e^mhZ\\nfneZmbhgh_`hh]lbg\en]bg`Z\\^llZk^Zl

E11

@^g^kZeZk^Zl_hklmZmb\^jnbif^gmghmli^\b_b^] êl^pa^k^!bglmbmnmbhgZeZg]in[eb\[nbe]bg`l"

E12 E13

jd!dG(f+"

Jd!dG"

+')

*'1

K^Z]bg`khhflpbma[hhdlmhkZ`^%^'`'eb[kZkb^l

-')

-'.

@^g^kZelmhkZ`^hma^kmaZgmahl^li^\b_b^]Z

+'-(f

0')

E14

?be^khhfl%_bebg`Zg]lmhkZ`^liZ\^!h__b\^l"

.')

-'.

E15

LmZ\dkhhfl![hhdl"

+'-(fa^bàm !fbg'/'."

0')

E16

IZi^klmhkZ`^Zg]lmZmbhg^krlmhk^l

-')(fa^bàm

2')

E17

=^gl^fh[be^lmZ\dbg`![hhdl"hgfh[be^mkhee^rlbg in[eb\Zg]bglmbmnmbhgZe[nbe]bg`l

-'1(fa^bàm

0')

E18

=^gl^fh[be^lmZ\dbg`![hhdl"hgfh[be^mkn\dlbg pZkâhnl^l

-'1(fa^bàm !fbg'*.')"

0')

E19

.')(fa^bàm !fbg'*.')"

2')

Bg]nlmkbZenl^

L^^;L>G*22*¾*¾*3 MZ[e^l/'./'/

>+

?hkdeb_ml
aEhp^k[hng]oZen^`bo^g'Fhk^li^\b_b\ehZ]oZen^llahne][^Z`k^^]pbma\eb^gm

MZ[e^+'0 ?Zg]@3mkZ__b\Zg]iZkdbg`Zk^Zl Ln[& \Zm^`hkr

>qZfie^

?

MkZ__b\Zg]iZkdbg`Zk^Zl!oâb\e^l5,)dG" MkZ__b\Zg]iZkdbg`Zk^Zl!oâb\e^l5,)dG"

@

jd!dG(f+"

Jd!dG"

+'.

.')

.')

Mh[^ ]^m^kfbg^]_hk li^\b_b\nl^

MkZ__b\Zg]iZkdbg`Zk^Zl!oâb\e^l7,)dG" MkZ__b\Zg]iZkdbg`Zk^Zl!oâb\e^l7,)dG"

10

Bfihl^]ehZ]l

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml MZ[e^+'1 A%BZg]D3khh_l Ln[& \Zm^`hkr

>qZfie^

A

Khh_l!bgZ\\^llb[e^^q\îm_hkfZbgm^gZg\^Zg]kîZbk"

jd!dG(f+" Khh_lehi^%a

B

5,)

)'/

,)5a5/)

)'/!/)¾a"(,)

5/)

)

Jd!dG"

)'2

Khh_l!Z\\^llb[e^pbmah\\niZg\r\Zm^`hkb^l:¾="
D


EC1-1-1: 6.3.4.1(2), Tables 6.9, 6.10, 6.11 & NA.7

Bfihl^]ehZ]l

:lMZ[e^l+'+mh+'.Z\\hk]bg`mh li^\b_b\nl^

Khh_l!Z\\^llb[e^_hkli^\bZel^kob\^l%^'`'_hkaêb\him^keZg]bg`Zk^Zl" Aêb\him^k\eZllA<*!5+)dG"!ln[c^\mmh ]rgZfb\_Z\mhkf 6*'-"

¾¾

+)

Aêb\him^k\eZllA<+!5/)dG"

¾¾

/)

Ghm^l 1Khh_lZk^\Zm^`hkbs^]Z\\hk]bg`mhma^bkZ\\^llb[bebmr'Bfihl^]ehZ]l_hkkhh_lmaZmZk^ghkfZeer Z\\^llb[e^Zk^`^g^kZeerma^lZf^Zl_hkma^li^\b_b\nl^Zg]\Zm^`hkrh_ma^Z]cZ\^gmZk^Z'Bfihl^] ehZ]l_hkkhh_lpbmahnmZ\\^llZk^`bo^gZ[ho^'

EC1-1-1: 6.3.4 & NA

2Ma^k^blgh\Zm^`hkrC'

Movable partitions Ma^lê_&p^bàmh_fhoZ[eîZkmbmbhglfZr[^mZd^gbgmhZ\\hngm[rZngb_hkfer]blmkb[nm^]ehZ]% jd%pab\alahne][^Z]]^]mhma^bfihl^]ehZ]lh_ÌhhklZl_heehpl3

EC1-1-1: 6.3.1.2 (8) & NA

N ?hkfhoZ[eîZkmbmbhglpbmaZlê_&p^bàmh_*')dG(fpZeee^g`ma3

jd6)'.dG(f+' N ?hkfhoZ[eîZkmbmbhglpbmaZlê_&p^bàmh_+')dG(fpZeee^g`ma3

jd6)'1dG(f+' N ?hkfhoZ[eîZkmbmbhglpbmaZlê_&p^bàmh_,')dG(fpZeee^g`ma3

jd6*'+dG(f+' A^Zob^kiZkmbmbhgllahne][^\hglb]^k^]lîZkZmêr'

+'-', Reduction factors General Khh_l ]h ghm jnZeb_r _hk ehZ] k^]n\mbhgl' Ma^ f^mah] `bo^g [êhp \hfieb^l pbma ma^ ND GZmbhgZe:gg^q[nm]b__^kl_khfmaZm`bo^gbgma^>nkh\h]^'

EC1-1-1: 6.3.1.2 (10) 6.3.1.2(11) & NA

Area : k^]n\mbhg _Z\mhk _hk bfihl^] ehZ]l _hk Zk^Z% a:% fZr [^ nl^] Zg] lahne] [^ ]^m^kfbg^] nlbg`3 a:6*')¾:(*)))ª)'0.

EC1-1-1: 6.3.1.2 (10) & NA Exp. (NA.1)

pa^k^

:blma^Zk^Z!f+"lniihkm^]pbmaehZ]ljnZeb_rbg`_hkk^]n\mbhg!b'^'\Zm^`hkb^l:mh>Zl eblm^]bgMZ[e^+'*"'

11

EC1-1-1: 6.3.1.2 (11) & NA Exp. ( NA.2)

Number of storeys :k^]n\mbhg_Z\mhk_hkgnf[^kh_lmhk^rl%ag%fZr[^nl^]Zg]lahne][^]^m^kfbg^]nlbg`3 ag6*'*¾g(*) ag6)'/ ag6)'. pa^k^

EC1-1-1: 6.3.1.2 (11) & NA

_hk*©g©. _hk.5g©*) _hkg7*)

g6gnf[^kh_lmhk^rlpbmaehZ]ljnZeb_rbg`_hkk^]n\mbhg!b'^'\Zm^`hkb^l:mh=Zleblm^]bg MZ[e^+'*"'

Use :\\hk]bg`mhma^NDG:%a:Zg]agfZrghm[^nl^]mh`^ma^k'


+'. Variable actions: snow loads EC1-1-3: 5.2(3)

EC1-1-3: 5.3.1, 5.3.2 & NA

Bgi^klblm^gmhkmkZglb^gmlbmnZmbhgl%lghpehZ]hgZkhh_%l%bl]^Ëg^]Zl[^bg`3 l6mb<^
lghpehZ]laZi^_Z\mhk%%^bma^km*hkm+ m*6ng]kb_m^]lghplaZi^_Z\mhk m+6]kb_m^]lghplaZi^_Z\mhk ?hkÌZmkhh_l%)6a!pbmaghabà^klmkn\mnk^l\ehl^hkZ[nmmbg`"% m*6m+6)'1 ?hklaZeehpfhghibm\akhh_l%)5a5,)!pbmaghabà^klmkn\mnk^l\ehl^hk Z[nmmbg`"%m*6)'1%m+6)'1!*$a(,)"?hkhma^k_hkflh_khh_Zg]eh\Ze^__^\ml k^_^kmh;L>G*22*¾*¾,L^\mbhgl.',Zg]/

EC1-1-3: 5.2(7) &Table 5.1

<^ 6

^qihlnk^\h^_Ë\b^gm ?hkpbg]lpîmmhih`kZiar<^6)'1 ?hkghkfZemhih`kZiar<^6*') ?hklaêm^k^]mhih`kZiar<^6*'+

EC1-1-3: 5.2(8)

EC1-1-3: & NA 2.8

ld 6 \aZkZ\m^kblmb\`khng]lghpehZ]dG(f+ 6 ) '*.!)'*S$)')."$!:$*))"(.+.

pa^k^ S 6 shg^gnf[^kh[mZbg^]_khfma^fZibg;L>G*22*¾*¾,G:?b`nk^G:'* : 6 lbm^Zembmn]^%f

? b`nk^G:'*h_ma^G:mh;L>G*22*¾*¾,Zelh`bo^lË`nk^l_hkldZm*))fZ'f'l'e' Zllh\bZm^]pbmama^shg^l'

? hkma^fZchkbmrh_ma^Lhnma>Zlm%ma^Fb]eZg]l%Ghkma^kgBkêZg]Zg]ma^ghkmah_ >gèZg]ZiZkm_khfabà`khng]%ld6)'.)dG(f+'

? hkma^P^lmgèZg]%ma^Ë`nk^blfhk^'L^^?b`nk^+'*'

LghpehZ]bl\eZllbË^]ZlZoZkbZ[e^Ëq^]Z\mbhg'>q\îmbhgZe\bk\nflmZg\^lfZr[^mk^Zm^]Zl Z\\b]^gmZeZ\mbhglbgpab\a\Zl^k^_^k^g\^lahne][^fZ]^mh;L>G*22*¾*¾,'

12


5 5 55

4

3 4

3

3 2

4 4

2

4

2

1


1 2 3 4 5

2

1

4

2

1 2

3

2 1 2

Zone 1 = 0.25 kN/m2 at 100 m a.m.s.l. Zone 1 = 0.40 kN/m2 at 100 m a.m.s.l. Zone 1 = 0.50 kN/m2 at 100 m a.m.s.l. Zone 1 = 0.60 kN/m2 at 100 m a.m.s.l. Zone 1 = 0.70 kN/m2 at 100 m a.m.s.l.

EC1-1-3: NA Fig. NA.1

4 2 3 4 2

3

1 ?b`nk^+'*
+'/ Variable actions: wind loads Mabl L^\mbhg ik^l^gml Z o^kr lbfie^ bgm^kik^mZmbhg h_ >nkh\h]^ *T**% **ZV Zg] bl bgm^g]^] mh ikhob]^ Z [Zlb\ ng]^klmZg]bg` pbma k^li^\m mh k^\mZg`neZk&ieZg [nbe]bg`l pbma ÌZm khh_l' Bg `^g^kZe%fZqbfnfoZen^lZk^`bo^g3pbmafhk^bg_hkfZmbhgZehp^koZen^fbàm[^nl^]'Ma^ nl^klahne][^\Zk^_nemh^glnk^maZmZgrbg_hkfZmbhgnl^]blpbmabgma^l\hi^h_ma^Ziieb\Zmbhg ^goblZ`^]'Ma^ nl^k bl k^_^kk^] mh fhk^ li^\bZeblm `nb]Zg\^T+,% +-V hk ;L >G *22*¾*¾-T+.V Zg] bmlNDGZmbhgZe:gg^qT+.ZV'Ma^GZmbhgZe:gg^qbg\en]^l\e^ZkZg]\hg\bl^Ìhp\aZkml_hkma^ ]^m^kfbgZmbhgh_i^Zdoêh\bmrik^llnk^%ji' Bg^ll^g\^\aZkZ\m^kblmb\pbg]ehZ]\Zg[^^qik^ll^]Zl3 pd6\_ji!s" pa^k^ \_ 6 _hk\^\h^_Ë\b^gm%pab\aoZkb^l%[nmblZfZq'h_*',_hkho^kZeeehZ] ji!s"6 \^!s"\^Mj[

pa^k^ \^!s" 6 ^qihlnk^_Z\mhk_khf?b`nk^+', \^M 6 mhpgm^kkZbg_Z\mhk_khf?b`nk^+'- j[ 6 )'))/o[+dG(f+ pa^k^ o[ 6 o[%fZi\Zem pa^k^ o[%fZi6 _ng]Zf^gmZe[Zlb\pbg]oêh\bmr_khf?b`nk^+'+ \Zem 6 Z embmn]^_Z\mhk%\hgl^koZmboêr%\Zem6*$)'))*: pa^k^ :6Zembmn]^Z'f'l'e

EC1-1-4: Figs NA.7, NA.8

EC1-1-4: Fig. NA.1

Lrf[hel Z[[kôbZmbhgl Zg] lhf^ h_ ma^ \Zo^Zml Zk^ ^qieZbg^] bg ma^ l^\mbhgl [êhp% pab\a mh`^ma^kikhob]^Zikh\^]nk^_hk]^m^kfbgbg`pbg]ehZ]mh;L>G*22*¾*¾-'

13

+'/'* Determine basic wind velocity, vb o[6\]bk\l^Zlhg\ikh[o[%)


EC1-1-4: 4.2(1) Note 2 & NA 2.4, 2.5

pa^k^ \]bk

EC1-1-4: 4.2(2) Note 3 & NA 2.7: Fig. NA.2

EC1-1-4: 4.2(1) Notes 4 & 5 & NA 2.8

EC1-1-4: 4.2(1) Note 2 & NA 2.4: Fig. NA.1

EC1-1-4: 4.2(2) Note 1 & NA 2.5

6 ]bk^\mbhgZe_Z\mhk
6 Z embmn]^_Z\mhk

pa^k^

:6Zembmn]^h_ma^lbm^bgf^mk^lZ'f'l'e' Pa^k^hkh`kZiarbllb`gbË\Zgm!b'^'ma^lbm^bl\ehl^mhZlehi^ lm^î^kmaZg)')."%k^_^kmhG:+'.

+'/'+ Calculate basic wind pressure, qb j[6)'.r o[+ EC1-1-4: 4.5(1) Note 2 & NA 2.18

pa^k^ o[ 6 ZlZ[ho^ r 6 ]^glbmrh_Zbk 6 *'++/d`(f,!6*+')G(f,"_hkND

+'/', Calculate peak wind pressure, qp(z) EC1-1-4: 4.5(1) Note 1 & NA 2.17

ji!s"6\^!s"j[_hk\hngmkreh\Zmbhgl 6\^!s"\^Mj[_hkmhpgeh\Zmbhgl pa^k^

EC1-1-4: 4.5(1) Note 1, NA 2.17 & Fig. A.NA.1

j[ 6 ZlZ[ho^

EC1-1-4: 4.5(1) Note 1 & NA 2.17: Fig. NA.7

\^!s" 6 ^qihlnk^_Z\mhk]^kbo^]_khf?b`nk^+',Zma^bàms!l^^[êhp"

EC1-1-4: 4.5(1) Note 1 & NA 2.17: Fig. NA.8

\^%M 6 ^qihlnk^\hkk^\mbhg_Z\mhk_hkmhpgm^kkZbg]^kbo^]_khf?b`nk^+'-

s

EC1-1-4: 7.2.2(1), Note & NA 2.26

14

6

maâ^bàmZmpab\ajibllhnàm ?hkZpbg]pZk]pZeeZg]pa^ga©[%jibl\Ze\neZm^]Zmma^k^_^k^g\â^bàm s^6a'?hkhma^kZli^\mkZmbhla3[h_ma^pbg]pZk]pZee%ji%bl\Ze\neZm^]Zm ]b__^k^gmk^_^k^g\â^bàml_hk^Z\aiZkm!l^^;L>G*22*¾*¾-"' pa^k^ a 6 a^bàmh_[nbe]bg` [ 6 [k^Z]mah_[nbe]bg` ?hke^^pZk]Zg]lb]^pZeel% s6a^bàmh_[nbe]bg`

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml 200

200 Use 1.0 in this area

31 30

4.0

100 90 80 70 60 50

29 28 27 26

3.5

40

100 90 80 70 60 50 40


25

20

30

3.0

z -hdis(m)

z -hdis(m)

30

10 20

0.9

23

10 9 8 7 6 5

22 24

4

2.5

2.0

3 2 ≤0.1

10 9 8 7 6 5

0.8

4 0.7

3 1.5 1 10 ≥100 Distance upwind to shoreline (km)

2 ≤0.1

1 10 ≥20 Distance inside town terrain (km)

Ghm^ Ln[c^\mmhZembmn]^\hkk^\mbhg'

Ghm^ @^g^kZeera]bl6)'?hkm^kkZbg\Zm^`hkrBO!mhpgl^m\'"l^^;L>G*22*¾*¾-3:'.'

?b`nk^+'+ FZih__ng]Zf^gmZe[Zlb\pbg] oêh\bmr%o[%fZi%!f(l"

?b`nk^+', >qihlnk^_Z\mhk\^!s"_hklbm^lbg\hngmkr hkmhpgm^kkZbg

EC1-1-4: 4.2(1) Note 2 & NA 2.4: Fig. NA.1

EC1-1-4: 4.5(1) Note 1 & NA 2.17: Fig. NA.7

?b`nk^+'- Fnembieb^k_hk^qihlnk^\hkk^\mbhg_hk lbm^lbgmhpgm^kkZbg EC1-1-4: 4.5(1) Note 1 & NA 2.17: Fig. NA.8

+'/'- Calculate characteristic wind load, wk pd6ji!s"\_ pa^k^ ji!s" \ _

6 6 6

ZlZ[ho^ _hk\^\h^_Ë\b^gm_hkma^lmkn\mnk^hklmkn\mnkZeê^f^gm @^g^kZeer \i^$\ib

pa^k^ \i^6 ! ^qm^kgZe"ik^llnk^\h^_Ë\b^gm]î^g]^gmhglbs^h_Zk^Z\hglb]^k^]Zg]shg^' ?hkZk^ZlZ[ho^*f+%\i^%*)lahne][^nl^]'

EC1-1-4: 7, 8 & NA

EC1-1-4: 7.2.1(1) Note 2 & NA. 2.25

Overall loads ?hkma^pZeelh_k^\mZg`neZk&ieZg[nbe]bg`l%\i^%*)fZr[^]^m^kfbg^]_khf MZ[e^0'*h_;L>G*22*¾*¾-'

EC1-1-4: 7.2.2(2) Note 1 & NA.2.27

hpô^k%_hkma^]^m^kfbgZmbhgh_ho^kZeeehZ]lhg[nbe]bg`l%ma^g^mik^llnk^ A \h^_Ë\b^gml`bo^gbgMZ[e^+'2fZr[^nl^]'Bgmabl\Zl^bmpbee[^ngg^\^llZkr mh]^m^kfbg^bgm^kgZepbg]ik^llnk^\h^_Ë\b^gml'

EC1-1-4: 7.2.2(2) Note 1 & NA.2.27, Table NA.4

Cladding loads ?hkZk^ZlZ[ho^*f+%\i^%*)lahne][^nl^]'\i^%*)fZr[^]^m^kfbg^]_khf MZ[e^0'*h_;L>G*22*¾*¾-'L^^MZ[e^+'*)'

EC1-1-4: 7.2.2(2) Note 1 & NA.2.27

15

Flat roofs ?hkÌZmkhh_l%Z\\hk]bg`mhma^:]oblhkrGhm^bgma^G:lhf^h_maôZen^l h_\i^%*)bgMZ[e^0'+h_;L>G*22*¾*¾-!l^^MZ[e^+'**"Zk^lb`gbË\Zgmer ]b__^k^gm_khf\nkk^gmikZ\mb\^bgma^ND'Bmk^\hff^g]lmaZm]^lb`g^kllahne] \hglb]^knlbg`maôZen^lbg;L/,223+mhfZbgmZbgma^\nkk^gmeôêlh_lZ_^mr Zg]^\hghfr'L^^MZ[e^+'*+'

EC1-1-4: NA.2.28 & NA advisory note

? hkhma^k_hkflh_khh_k^_^kmh;L>G*22*¾*¾-Zg]ma^NDG:' BmpbeeZelh[^g^\^llZkrmh]^m^kfbg^bgm^kgZepbg]ik^llnk^\h^_Ë\b^gml_hk ma^]^lb`gh_\eZ]]bg`'

EC1-1-4: 7.2.9(6) Note 2

EC1-1-4: NA 2.27, Table NA.4

MZ[e^+'2 G^mik^llnk^\h^__b\b^gm%\i^%*)%_hkpZeelh_k^\mZg`neZkieZg[nbe]bg`l#

EC1-1-4: 7.2.3, NA.2.28 & NA advisory note


BS 6399: Table 8 & Fig. 18

\ib 6 bgm^kgZeik^llnk^\h^_Ë\b^gm' ?hkgh]hfbgZgmhi^gbg`l\ibfZr[^mZd^gZlma^fhk^hg^khnlh_$)'+Zg]¾)',

a(] 5 1 ª 0.25

G^mik^llnk^\h^__b\b^gm%\i^%*) *', *'* )'1

Ghm^l *#bg^__^\mma^lôZen^lZk^_hk\^\h^__b\b^gml_hk]^m^kfbgbg`ho^kZeeehZ]lhg[nbe]bg`l' +a6a^bàmh_[nbe]bg`' ,[6[k^Z]mah_[nbe]bg`!i^ki^g]b\neZkmhpbg]"' -]6]îmah_[nbe]bg`!iZkZeeêmhpbg]"' .OZen^lfZr[^bgm^kiheZm^]' />q\en]^l_nggêebg`'

EC1-1-4: 7.2.2(2) Table 7.1, Note 1 & NA 2.27: Tables NA.4a , NA.4b

MZ[e^+'*) >qm^kgZeik^llnk^\h^__b\b^gm%\i^%*)%_hkpZeelh_k^\mZg`neZk&ieZg[nbe]bg`l =^l\kbimbhg

Zone A

?hkpZeeliZkZeeêmhma^pbg]]bk^\mbhg%Zk^Zlpbmabg )'+fbgT[4+aVh_pbg]pZk]^]`^

¾*'+

Zone B

?hkpZeeliZkZeeêmhma^pbg]]bk^\mbhg%Zk^Zlpbmabg )'+fbgT[4+aVh_pbg]pZk]^]`^

¾)'1

Zone C

?hkpZeeliZkZeeêmhma^pbg]]bk^\mbhg%Zk^Zl_khf )'+fbgT[4+aVmhfbgT[4+aVh_pbg]pZk]^]`^

Zone D

Pbg]pZk]pZee

$)'1

Zone E

E^^pZk]pZee

FZq'

Zones D G^m and E Ghm^l *a6a^bàmh_[nbe]bg`' +[6[k^Z]mah_[nbe]bg`!i^ki^g]b\neZkmhpbg]"' EC1-1-4: 7.2, Table 7.2 & NA

\i^%*)

Shg^

¾)'.

¾)'0 $*',

MZ[e^+'** >qm^kgZeik^llnk^\h^__b\b^gm%\i^%*)_hk_eZmkhh_l# Shg^

=^l\kbimbhg

\i^%*) LaZki^]`^ Zm^Zo^l

16

Fbg'

PbmaiZkZi^m

Zone F

Pbmabg)'*fbgT[4+aVh_pbg]pZk]^]`^Zg]pbmabg ¾*'1 )'+fbgT[4+aVh_k^mnkg^]`^!iZkZeeêmhpbg]]bk^\mbhg"

¾*'/

Zone G

Pbmabg)'*fbgT[4+aVh_pbg]pZk]^]`^Zg]hnmpbma ¾*'+ )'+fbgT[4+aVh_k^mnkg^]`^!iZkZeeêmhpbg]]bk^\mbhg"

¾*'*

Zone H

Khh_[^mp^^g)'*fbgT[4+aVZg])'.fbgT[4+aV_khf pbg]pZk]^]`^

¾)'0

¾)'0

Zone I K^fZbg]^k[^mp^^g)'.fbgT[4+aVZg]e^^pZk]^]`^ ¨)'+ ¨)'+ Ghm^l *#:\\hk]bg`mhG:mh;L>G*22*&*&-%mablmZ[e^blghmk^\hff^g]^]_hknl^bgma^ND' +a6a^bàmh_[nbe]bg`' ,[6[k^Z]mah_[nbe]bg`!i^ki^g]b\neZkmhpbg]"'

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml MZ[e^+'*+ >qm^kgZeik^llnk^\h^__b\b^gm%\i^%_hk_eZmkhh_l


Shg^

=^l\kbimbhg

EC1-1-4: 7.2.3, NA.2.28 & NA advisory note.

\i^ LaZki^]`^ Zm^Zo^l

PbmaiZkZi^m

Zone A

Pbmabg)'*fbgT[4+aVh_pbg]pZk]^]`^Zg]pbmabg )'+.fbgT[4+aVh_k^mnkg^]`^!iZkZeeêmhpbg]]bk^\mbhg"

¾+')

¾*'2

Zone B

Pbmabg)'*fbgT[4+aVh_pbg]pZk]^]`^Zg]hnmpbma )'+.fbgT[4+aVh_k^mnkg^]`^!iZkZeeêmhpbg]]bk^\mbhg"

¾*'-

¾*',

Zone C

Khh_[^mp^^g)'*fbgT[4+aVZg])'.fbgT[4+aV_khf pbg]pZk]^]`^

¾)'0

¾)'0

Zone D

K^fZbg]^k[^mp^^g)'.fbgT[4+aVZg]e^^pZk]^]`^

¨)'+

¨)'+

BS 6399: Table 8 & Fig. 18

Ghm^l *a6a^bàmh_[nbe]bg`' +[6[k^Z]mah_[nbe]bg`!i^ki^g]b\neZkmhpbg]"'

+'/'. Calculate the overall wind force, Fw ?p6\l\]Spd :k^_ pa^k^

EC1-1-4: 5.3.2, Exp. (5.4) & NA

pd 6 ZlZ[ho^

EC1-1-4: 6.2(1) a), 6.2(1) c)

\l\] 6 lmkn\mnkZe_Z\mhk%\hgl^koZmboêr 6 *') hkfZr[^]^kbo^] pa^k^ \l 6 lbs^_Z\mhk \lfZr[^]^kbo^]_khf>qi'!/'+"hkmZ[e^G:','=î^g]bg`hgoZen^lh_ ![$a"Zg]!s¾a]bl"Zg]]bob]bg`bgmhShg^:%;hk<%ZoZen^h_\l !Z_Z\mhk5*'))"fZr[^_hng]'

\]6 ]rgZfb\_Z\mhk \]fZr[^]^kbo^]_khf>qi'!/',"hkË`nk^G:'2'=î^g]bg`hgoZen^lh_dl !eh`Zkbmafb\]^\k^f^gmh_lmkn\mnkZe]Zfibg`"Zg]a([%ZoZen^h_\]!Z_Z\mhk7 *'))"fZr[^_hng]'

\ ]fZr[^mZd^gZl*')_hk_kZf^][nbe]bg`lpbmalmkn\mnkZepZeelZg]fZlhgkr bgm^kgZepZeel%Zg]_hk\eZ]]bgìZgêlZg]ê^f^gml

:k^_6k^_^k^g\^Zk^Zh_ma^lmkn\mnk^hklmkn\mnkZeê^f^gm

+'0 Variable actions: others :\mbhgl]n^mh\hglmkn\mbhg%mkZ_Ë\%Ëk^%ma^kfZeZ\mbhgl%nl^Zllbehlhk_khf\kZg^lZk^hnmlb]^ ma^l\hi^h_mablin[eb\ZmbhgZg]k^_^k^g\^lahne][^fZ]^mhli^\bZeblmebm^kZmnk^'

EC1-1-4: 6.2(1) e) & NA.2.20

EC1-1-4: 6.3(1), Exp. (6.2) & NA.2.20, Table NA3

EC1-1-4: 6.3(1), Exp. (6.3) & NA.2.20: Fig. NA9 EC1-1-4: 5.3.2, Exp. (5.4) & NA

EC1-1-6, EC1-2, EC1-1-2, EC1-1-5, EC1-3 & EC1-4

17

+'1 Permanent actions Ma^ ]^glbmb^l Zg] Zk^Z ehZ]l h_ \hffhger nl^] fZm^kbZel% la^^m fZm^kbZel Zg] _hkfl h_ \hglmkn\mbhgZk^`bo^gbgMZ[e^l+'*,mh+'*.' :\mbhglZkblbg`_khfl^mme^f^gm%]^_hkfZmbhgZg]\k^îZk^hnmlb]^ma^l\hi^h_mabl]h\nf^gm [nm `^g^kZeer Zk^ mh [^ \hglb]^k^] Zl i^kfZg^gm Z\mbhgl' Pa^k^ \kbmb\Ze% k^_^k mh li^\bZeblm ebm^kZmnk^' MZ[e^+'*, ;ned]^glbmb^l_hklhbelZg]fZm^kbZelT**%+/V dG(f,

;ned]^glbmb^l

*2¾++

+.')

*/¾*2

+/')

;ned]^glbmb^l


Lhbel

FZm^kbZel

@kZgneZk¾ehhl^

*/¾*1

@eZll

+.'/

@kZgneZk¾]^gl^

*2¾+*

@kZgbm^

+0',

Lbemr\eZr%lZg]r\eZr

*/¾+)

AZk]\hk^

*2')

Ebf^lmhg^!IhkmeZg]lmhg^¾f^]'p^bàm" ++')

FZm^kbZel

18

dG(f,

:liaZem

++'.

;eh\dl¾Z^kZm^]\hg\k^m^!fbg'"

.')

Ebf^lmhg^!fZk[e^¾a^Zorp^bàm"

+/'0

FZ\Z]ZfiZobg`

+*')

;eh\dl¾Z^kZm^]\hg\k^m^!fZq'"

2')

;eh\dl¾]^gl^Z``k^`Zm^

+)')

;eh\dl¾ebàmp^bàm

*-')

;hhdl¾[nedlmhkZ`^

1¾**

LZg]lmhg^

+,'.

;kb\dphkd¾[en^

+-')

L\k^^]¾lZg](\^f^gm

++')

;kb\dphkd¾^g`bg^^kbg`

++')

Lm^ê(bkhg

00')

;kb\dphkd¾_e^mmhg

*1')

M^kkZ\hmmZ

+)'0

;kb\dphkd¾Ehg]hglmh\d

*2')

Mbf[^k¾=hnèZl_bk

.'+

;kb\dphkd¾lZg]ebf^

+*')

Mbf[^k¾>nkhi^Zg[^^\a(hZd

0'*

/'2

Mbf[^k¾@kZ]^<*/

,'/

*)')

Mbf[^k¾@kZ]^<+-

-'*

Mbf[^k¾Bkhdh(m^Zd

/'-

*1')

+-')

F=?

1')

IeZlm^k

*-'*

Ierphh]

/',

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml MZ[e^+'*- Mrib\ZeZk^ZehZ]l_hk\hg\k^m^leZ[lZg]la^^mfZm^kbZelT**%+/V Mrib\ZeZk^ZehZ]l

dG(f+


Ik^\Zlm\hg\k^m^lheb]ngbml!*))ff"

Mrib\ZeZk^ZehZ]l

dG(f+

La^^mfZm^kbZel +'.)

IeZlm^kldbf\hZm

)').

Ik^\Zlm\hg\k^mâheehp\hk^ngbmlZ!*.)ff" +'-)

IeZlm^k[hZk]!*+'.ff"

)')2

Ik^\Zlm\hg\k^mâheehp\hk^ngbmlZ!+))ff" +'10

IeZlm^k[hZk]!*2ff"

)'*.

Ik^\Zlm\hg\k^m^'aheehp\hk^ngbmlZ!,))ff" -')0

Ierphh]!*+'.ff"

)')1

Ik^\Zlm\hg\k^mâheehp\hk^ngbmlZ!-))ff"

-'1-

Ierphh]!*2ff"

)'*+

Kb[[^]leZ[[!+.)ff"

-'))

JnZkkrmbe^lbg\en]bg`fhkmZk[^]]bg`

)',+

Kb[[^]leZ[[!,))ff"

-',)

KZbl^]_ehhk¾a^Zor]nmr

)'.)

Kb[[^]leZ[[!,.)ff"

-'0)

KZbl^]_ehhk¾f^]bnfp^bàm

)'-)

PZ__e^leZ[\¾lmZg]Zk]fhne]l!,+.ff" /'))

KZbl^]_ehhk¾ebàmp^bàm

)',)

PZ__e^leZ[\¾lmZg]Zk]fhne]l!-+.ff" 0',)

K^g]^k!*,ff"

)',)

PZ__e^leZ[\¾lmZg]Zk]fhne]l!.+.ff" 1'/)

L\k^^]¾.)ff

*'*.

La^^mfZm^kbZel

L\k^^]¾ebàmp^bàm!+.ff"

)'-.

:liaZem!+)ff"

)'-/

LmZbge^lllm^êkhh_bg`!)'-ff"

)').

)').

Lnli^g]^]\^bebg`¾lm^ê

)'*)

)'*+

Lnli^g]^]_b[k^[hZk]mbe^l

)').

=krebgbg`hglmn]!+)ff"

)'*.

M@[hZk]l!*.'.ff"

)')2

?Zel^\^bebg`¾lm^ê_kZfbg`

)'*)

M@[hZk]l!++ff"

)'*+

?êm!,eZr^k"Zg]\abiibg`l

)',.

Mbe^l¾\^kZfb\_ehhkhg[^]]bg`

*'))

@eZll¾]hn[e^èZsbg`

)'.+

;Zmm^gl_hkleZmbg`Zg]mbebg`

)'),

@eZll¾lbgè^èZsbg`

)',)

Mbe^l¾\eZrkhh_!fZq"

)'/0

BglneZmbhg¾èZll_b[k^!*.)ff"

)'),

Mbe^l¾gZmnkZeleZm^!mab\d"

)'/.

IZobg`lmhg^l!.)ff"

*'+)

Mbe^l¾bgm^keh\dbg`\hg\k^m^

)'..

IeZlm^k¾mph\hZm`rilnf!*+ff"

)'+*

Mbe^l¾ieZbg\hg\k^m^

)'0.

D^r ZAheehp\hk^_b`nk^lZllnf^ghmhiibg`!.)fflmkn\mnkZemhiibg`:*'+.dG(f+" [Kb[[^]leZ[l3*.)p^[90.)\^gmk^lpbma*))ffmab\d_eZg`^(leZ['P^[lehi^*3*) \PZ__e^leZ[l3*.)kb[l92))\^gmk^lpbma*))ffmab\d_eZg`^(leZ['P^[lehi^*3*)

19


MZ[e^+'*. EhZ]l_hkmrib\Ze_hkflh_\hglmkn\mbhgT+/V
!dG(f+"

K^lb]^gmbZe_ehhk

;kb\dphkd*)+'.ff

+'-)

)').

BglneZmbhg.)ff

)')+

?ehZmbg`_ehhk

)'*. /'+.

;eh\dphkd*))ff

*'-)

Lê_&p^bàmh_+.)fflheb]leZ[

)'+*

Lnli^g]^]\^bebg`

)'+)

MhmZe

-')

)'*)

Ebàmp^bàm\eZ]]bg`

!dG(f+"

L^kob\^l

BglneZm^]iZgê

)'+)

Inkebgl

)').

=krebgbg`hglmn]

)'*.

MhmZe

)'-)

MhmZe

/'0.

L\ahhe_ehhk

!dG(f+"

)').


/'+. )'*.

!dG(f+"

Lnli^g]^]\^bebg`

:eehp

*'))

L^kob\^l

)'+)

Ik^\Zlm\hg\k^m^\eZ]]bg`

!dG(f+"

MhmZe

/'/)

?Z\bg`

*'))

AhlibmZe_ehhk

!dG(f+"

Ik^\ZlmiZgê!*))ff"

+'-)

?ehhkbg`

)').

BglneZmbhg

)').


/'+.

=krebgbg`hglmn]

)'*.

L\k^^]

+'+) )'*.

MhmZe

,'/)

Lnli^g]^]\^bebg`

=krebgbg`

!dG(f+"

L^kob\^l![nm\Zg[^`k^Zm^k"

)').

F^mZelmn]l

)').

MhmZe

1'0)

?eZmkhh_(^qm^kgZem^kkZ\^

!dG(f+"

IZobg`hk`kZoê%Zeehp

+'+)

IeZlm^k[hZk]Zg]ldbf+

)'-)

MhmZe

)'-.

Mbf[^klmn]pZee

!dG(f+"

Mbf[^klmn]l

)'*)

PZm^kikhh_bg`

)'.)

BglneZmbhg

)'*)

IeZlm^k[hZk]Zg]ldbf+

)'-)

MhmZe

)'.)

Lê_&p^bàmh_+.)fflheb]leZ[\^bebg`

/'+.

H__b\^_ehhk

!dG(f+"

Lnli^g]^]\^bebg`

)'*.

)'),

L^kob\^l

)',)

KZbl^]_ehhk

)',)

MhmZe

2'.)


/'+.

Mbf[^kibm\a^]khh_

!dG(f+"

Lnli^g]^]\^bebg`

)'*.

Mbe^l!kZg`^)'.)¾)'0."

)'0.

L^kob\^l

)',)

;Zmm^gl

)').

MhmZe

0'),

?êm

)').

H__b\^\hk^Zk^Z

!dG(f+"

KZ_m^kl

)'*.

Mbe^lZg][^]]bg`%Zeehp

*'))

BglneZmbhg

)').

L\k^^]

+'+)

IeZlm^k[hZk]ldbf

)'*.


/'+.

L^kob\^l

)'*)

Lnli^g]^]\^bebg`

)'*.

L^kob\^l

)',)

MhmZe

2'2)

LmZbkl

!dG(f+"

*.)ffpZblm! z *0.9+.dG(f,"

-'-)

Mk^Z]l)'*.)'+.-(+9+.dG(f,

*'11

<^bebg`chblml

)'*.

MhmZei^ki^g]b\neZkmhkhh_

*'-.

MhmZehgieZgZllnfbg`,)ibm\a

*'/)

F^mZe]^\dbg`khh_

!dG(f+"

BglneZm^]iZgê

)'+)

*'*)

Inkebgl

)'*) )',)

)'+*

Lm^êphkd

?bgbla3mbe^l[^]]bg`

*'))

L^kob\^l

)'*)

MhmZe

1'/)

MhmZe

)'0)

IeZlm^k

20

!dG(f+"

IeZlm^k

L\k^^])').9++dG(f,

+'.\EhZ]l_hkmrib\Ze_hkflh_\hglmkn\mbhg MZ[e^+'*- +'.\EhZ]l_hkmrib\Ze_hkflh_\hglmkn\mbhg

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml +'2 Design values of actions +'2'* General case Ma^]^lb`goZen^h_ZgZ\mbhg%?] %maZmh\\nklbgZehZ]\Zl^bl

?]6g?c ?d


pa^k^ g? 6iZkmbZe_Z\mhk_hkma^Z\mbhgZ\\hk]bg`mhmaêbfbmlmZm^ng]^k\hglb]^kZmbhg'MZ[e^ +'*/bg]b\Zm^lmaîZkmbZe_Z\mhklmh[^nl^]bgma^ND_hkma^\hf[bgZmbhglh_ kîk^l^gmZmbo^Z\mbhglbg[nbe]bg`lmkn\mnk^l' c ?d fZr[^\hglb]^k^]Zlma^kîk^l^gmZmbo^Z\mbhg%?kî%ZiikhikbZm^mhmaêbfbmlmZm^ [^bg`\hglb]^k^]

pa^k^ c 6 Z_Z\mhkmaZm\hgo^kmlma^\aZkZ\m^kblmb\oZen^h_ZgZ\mbhgbgmhZkîk^l^gmZmbo^ oZen^'BmZ]cnlmlmaôZen^h_ma^Z\mbhgmhZ\\hngm_hkma^gZmnk^h_maêbfbm lmZm^ng]^k\hglb]^kZmbhgZg]ma^chbgmikh[Z[bebmrh_ma^Z\mbhglh\\nkkbg` lbfnemZg^hnler'Bm\ZgZllnf^maôZen^h_*')_hkZi^kfZg^gmZ\mbhghkc) hkc*hkc+_hkZoZkbZ[e^Z\mbhg'MZ[e^+'*0lahplahp\aZkZ\m^kblmb\oZen^lh_ oZkbZ[e^Z\mbhglZk^\hgo^km^]bgmhkîk^l^gmZmboôZen^l'MablmZ[e^bl]^kbo^] _khf;L>G*22)T*)VZg]bmlGZmbhgZe:gg^qT*)ZV' ?d 6 \aZkZ\m^kblmb\oZen^h_ZgZ\mbhgZl]^Ëg^]bgL^\mbhgl+'+Zg]+','

MZ[e^+'*/ IZkmbZe_Z\mhkl!g?"_hknl^bgo^kb_b\Zmbhgh_ebfbmlmZm^lbgi^klblm^gmZg]mkZglb^gm]^lb`glbmnZmbhgl EbfbmlmZm^

I^kfZg^gmZ\mbhgl !@d"

E^Z]bgòZkbZ[e^Z\mbhg :\\hfiZgrbgòZkbZ[e^ !Jd%*" Z\mbhgl!Jd%b"]

*'*)!)'2"Z

*'.)!)')"Z

EC0: Tables A1.2(A), A1.2(B), A1.2(C), A1.4 & NA

Z">jnbeb[kbnf!>JN" c)%b*'.)!)')"Z

["Lmk^g`maZmNEL!LMK(@>H"ghmbgoheobg``^hm^\agb\ZeZ\mbhgl Either >qi'!/'*)"

*',.!*')"Z

*'.

c)*'.

*',.!*')"Z

c)*'.

c)*'.

*'+.!*')"Z

*'.

c)*'.

or the worst case of >qi'!/'*)Z" and >qi'!/'*)["

\"Lmk^g`maZmNEL!LMK(@>H"pbma`^hm^\agb\ZeZ\mbhgl Worst case of L^m;

*',.!*')"Z

*'.!)')"Z

*')

*',

and L^m< ]"L^kob\^Z[bebmr
*'))

*'))

c)%b*'))

?k^jn^gm

*'))

c*%**'))

c+%b*'))

JnZlb&i^kfZg^gm

*'))

c+%**'))

c+%b*'))

*')

:][

c*%b!fZbg" c+%b!hma^kl"

*')

:>]\

c+%b

^":\\b]^gmZe]^lb`glbmnZmbhgl >qi'!/'**Z" _"L^blfb\ >qi'!/'*+Z(["

D^r Z OZen^b__ZohnkZ[e^!lahpgbg[kZ\d^ml" [ E^Z]bg`Z\\b]^gmZeZ\mbhg%:]%blng_Z\mhk^] \ L^blfb\Z\mbhg%:>] ] K^_^kmh;L>G*22)3:*'+'+G:

Ghm^l * MaôZen^lh_cZk^`bo^gbgMZ[e^+'*0' + @^hm^\agb\ZeZ\mbhgl`bo^gbgma^mZ[e^ Zk^[Zl^]hg=^lb`g:iikhZ\a*bg G*22)%pab\abl k^\hff^g]^]bgbmlGZmbhgZe:gg^q'

21

+'2'+ Design values at ULS ?hkma^NELh_lmk^g`ma!LMK"%ma^]^lb`g^kfZr\ahhl^[^mp^^gnlbg`>qik^llbhg!/'*)"hkma^ phklm\Zl^h_>qik^llbhg!/'*)Z"hk>qik^llbhg!/'*)["'

EC0: 6.4.3.2(3)

Single variable action :mNEL%ma^]^lb`goZen^h_Z\mbhglbl ^bma^k


>qi'!/'*)" *',.@d$*'.Jd%* hkma^phklm\Zl^h_3 >qi'!/'*)Z" *',.@d$c)%**'.Jd%* Zg] >qi'!/'*)[" *'+.@d$*'.Jd%* pa^k^ @d 6 i^kfZg^gmZ\mbhg Jd%*6 lbgèôZkbZ[e^Z\mbhg c)%*6 \hf[bgZmbhg_Z\mhk_hkZlbgèôZkbZ[eêhZ]!l^^MZ[e^+'*0" MZ[e^+'*0 OZen^lh_c_Z\mhkl EC0: A1.2.2 & NA

EC1-1-1: 3.3.2

:\mbhg

c)

c*

c+

Bfihl^]ehZ]lbg[nbe]bg`l

Category A: domestic, residential areas

)'0

)'.

)',

Category B: office areas

)'0

)'.

)',

Category C: congregation areas

)'0

)'0

)'/

Category D: shopping areas

)'0

)'0

)'/

Category E: storage areas

*')

)'2

)'1

Category F: traffic area (vehicle weight © 30 kN)

)'0

)'0

)'/

Category G: traffic area (30 kN < vehicle weight © 160 kN)

)'0

)'.

)',

Category H: roofsZ

)'0

)')

)')

Snow loads where altitude © 1000 m a.m.s.l.Z

)'.

)'+

)')

Wind loadsZ

)'.

)'+

)')

Temperature effects (non-fire)Z

)'/

)'.

)')

D^r a Hgkhh_l%bfihl^]ehZ]l%lghpehZ]lZg]pbg]ehZ]llahne]ghm[^Ziieb^]mh`^ma^k' Ghm^l 1 Ma^gnf^kb\ZeoZen^l`bo^gZ[ho^Zk^bgZ\\hk]Zg\^pbma;L>G*22)Zg]bmlNDGZmbhgZe:gg^q' 2
>qik^llbhg!/'*)"e^Z]lmhma^nl^h_g?6g@6*',._hki^kfZg^gmZ\mbhglZg]g?6gJ6*'.)_hk oZkbZ[e^Z\mbhgl!g@_hki^kfZg^gmZ\mbhglblbgm^g]^]mh[^\hglmZgmZ\khllZeeliZgl"' >qik^llbhg!/'*)"blZepZrl^jnZemhhkfhk^\hgl^koZmbo^maZgmaê^ll_ZohnkZ[e^h_>qik^llbhgl !/'*)Z"Zg]!/'*)["'>qik^llbhg!/'*)["pbeeghkfZeerZiierpa^gmaî^kfZg^gmZ\mbhglZk^ghm `k^Zm^kmaZg-'.mbf^lmaôZkbZ[e^Z\mbhgl!^q\îm_hklmhkZ`êhZ]l%\Zm^`hkr>bgMZ[e^+'*0% pa^k^>qik^llbhg!/'*)Z"ZepZrlZiieb^l"' Ma^k^_hk^%^q\îmbgma^\Zl^h_\hg\k^m^lmkn\mnk^llniihkmbg`lmhkZ`êhZ]lpa^k^c)6*')% hk_hkfbq^]nl^%>qik^llbhg!/'*)["pbeenlnZeerZiier'Manl%_hkf^f[^kllniihkmbgò^kmb\Ze Z\mbhglZmNEL%*'+.@d$*'.Jdpbee[^ZiikhikbZm^_hkfhlmlbmnZmbhglZg]Ziieb\Z[e^mhfhlm \hg\k^m^lmkn\mnk^l!l^^?b`nk^+'."' qik^llbhg!/'*)"%ma^nl^h_^bma^k>qik^llbhg!/'*)Z"hk!/'*)["e^Z]l mh Z fhk^ \hglblm^gm kêbZ[bebmr bg]^q Z\khll ebàmp^bàm Zg] a^Zorp^bàm fZm^kbZel'

22

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml 50

gk kN/m (or kN/m2)

40

Use Exp. (6.10a)

30

Use Exp. (6.10b)

10 0


Ghm^ :llnfbg`c)6)'0 b'^'Ziieb\Z[e^mhZeeZk^Zl ^q\îmlmhkZ`^'

20

1

2

3

4

5

6

7

8

9

10

q k kN/m (or kN/m2) ?b`nk^+'. Pa^gmhnl^>qi'!/'*)Z"hk>qi'!/'*)["

Accompanying variable actions :`Zbg ma^ ]^lb`g^k fZr \ahhl^ [^mp^^g nlbg` >qik^llbhg !/'*)" hk ma^ e^ll _ZohnkZ[e^ h_ >qik^llbhgl!/'*)Z"hk!/'*)["'

EC0: 6.4.3.2(3)

>bma^k >qi'!/'*)" *',.@d$*'.Jd%*$S!c)%b*'.Jd%b " hkma^phklm\Zl^h_3 >qi'!/'*)Z" *',.@d$c)%**'.Jd%*$S!c)%b*'.Jd%b" Zg] >qi'!/'*)[" *'+.@d$*'.Jd%*$S!c)%b*'.Jd%b" pa^k^ @d 6 i^kfZg^gmZ\mbhg Jd%*6 *lmoZkbZ[e^Z\mbhg Jd%b 6 bmaoZkbZ[e^Z\mbhg c)%*6 \aZkZ\m^kblmb\\hf[bgZmbhg_Z\mhk_hk*lmoZkbZ[eêhZ]!l^^MZ[e^+'*0" c)%b 6 \aZkZ\m^kblmb\\hf[bgZmbhg_Z\mhk_hkbmaoZkbZ[eêhZ]!l^^MZ[e^+'*0" Bgma^Z[ho^%Jd%*!Zg]c)%b "k^_^klmhmaê^Z]bgòZkbZ[e^Z\mbhgZg]Jd%b!Zg]c)%b "k^_^klmh Z\\hfiZgrbg`bg]î^g]^gmoZkbZ[e^Z\mbhgl'Bg`^g^kZe%ma^]blmbg\mbhg[^mp^^gma^mphmri^lh_ Z\mbhglpbee[^h[obhnl!l^^?b`nk^+'/"4pa^k^bmblghm%^Z\aehZ]lahne]bgmnkg[^mk^Zm^]Zlma^ e^Z]bg`Z\mbhg':elh%ma^gnf^kb\ZeoZen^l_hkiZkmbZe_Z\mhkl`bo^gbgma^NDGZmbhgZe:gg^qT*)ZV Zk^nl^]bgma^^jnZmbhglZ[ho^'MaôZen^h_c)]î^g]lhgma^nl^h_ma^[nbe]bg`Zg]lahne] [^h[mZbg^]_khfma^NDGZmbhgZe:gg^q_hk;L>G*22)!l^^MZ[e^+'*0"'

EC0: A1.2.2, A1.3.1 & NA

qk2 gk2 qk1 gk1 qk1 gk1

qk3 = wk

qk1 gk1 qk1 gk1 A ?b`nk^+'/ Bg]î^g]^gmoZkbZ[e^Z\mbhgl

B

C

Ghm^ @^g^kZeermaôZkbZ[e^ Z\mbhglhgZmrib\Zeh__b\^ [eh\dphne][^\hglb]^k^] Zl[^bg`mak^^l^mlh_ bg]î^g]^gmoZkbZ[e^ Z\mbhgl3 *' Bfihl^]h__b\êhZ]l hgma^h__b\^_ehhkl' +' Khh_bfihl^]ehZ]' ,' Pbg]ehZ]'

23

Ma^^qik^llbhglmZd^bgmhZ\\hngmmaîkh[Z[bebmrh_chbgmh\\nkk^g\^h_ehZ]l[rZiierbg`ma^ c)%b_Z\mhkmhma^Z\\hfiZgrbgòZkbZ[e^Z\mbhg'Maîkh[Z[bebmrmaZmma^l^\hf[bg^]Z\mbhglpbee [^^q\^^]^]bl]^^f^]mh[^lbfbeZkmhmaîkh[Z[bebmrh_Zlbgè^Z\mbhg[^bg`^q\^^]^]' B_ma^mphbg]î^g]^gmoZkbZ[e^Z\mbhglJd%*Zg]Jd%+Zk^Zllh\bZm^]pbma]b__^k^gmliZglZg]ma^ nl^h_>qik^llbhg!/'*)["blZiikhikbZm^%ma^gbghg^l^mh_ZgZerl^lZiier *'+.@d$*'.Jd%*mhma^Jd%*liZgl Zg]*'+.@d$c)'b*'.Jd%*mhma^Jd%+liZgl' BgZllh\bZm^]ZgZerl^lZiier *'+.@d$c)%b*'.Jd%*mhma^Jd%*liZgl Zg]*'+.@d$*'+.Jd%+mhma^Jd%+liZgl'


L^^>qZfie^+'**'+!mphoZkbZ[e^Z\mbhgl"'

+'2', Design values at SLS EC0: 6.5 & Table A1.4

Ma^k^Zk^mak^^\hf[bgZmbhglh_Z\mbhglZmLEL!hkehZ]\hf[bgZmbhgZmLEL"'Ma^l^Zk^`bo^gbg MZ[e^+'*1'Ma^\hf[bgZmbhgZg]oZen^mh[^nl^]]î^g]lhgma^gZmnk^h_maêbfbmlmZm^[^bg` \a^\d^]' JnZlb&i^kfZg^gm \hf[bgZmbhgl Zk^ Zllh\bZm^] pbma ]^_hkfZmbhg% \kZ\d pb]mal Zg] \kZ\d\hgmkhe'?k^jn^gm\hf[bgZmbhglfZr[^nl^]mh]^m^kfbg^pa^ma^kZl^\mbhgbl\kZ\d^]hk ghm'Ma^gnf^kb\oZen^lh_c)%c*Zg]c+Zk^`bo^gbgMZ[e^+'*0'
EC0: Table A1.4

MZ[e^+'*1 IZkmbZe_Z\mhklmh[^Ziieb^]bgmaô^kb_b\Zmbhgh_ma^LEL Permanent actions Gk

Variable actions Qk

Unfavourablea

Favourablea

Leadingb

Othersb

Characteristic

@d%lni

@d%bg_

Jd%*

c)%bJd%b

Frequent

@d%lni

@d%bg_

c*%*Jd%*

c+%bJd%b

Quasi-permanent

@d%lni

@d%bg_

c+%*Jd%*

c+%bJd%b

Combination

D^r a @^g^kZeer@d%lniZg]@d%bg_fZr[^mZd^gZl@d'L^^L^\mbhg+'2'. b c_Z\mhklZk^`bo^gbgMZ[e^+'*0

+'2'- Design values for other limit states EhZ]\hf[bgZmbhglZk^`bo^gbgMZ[e^+'*/_hk Z">jnbeb[kbnf!>JN"% ["Lmk^g`maZmNELghmbgoheobg``^hm^\agb\ZeZ\mbhgl% \"Lmk^g`maZmNELpbma`^hm^\agb\ZeZ\mbhgl% ]"L^kob\^Z[bebmr% ^":\\b]^gmZeZg] _"L^blfb\]^lb`glbmnZmbhgl'

24

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml +'2'. Variations in permanent actions Pa^gmaôZkbZmbhgh_Zi^kfZg^gmZ\mbhgblghmlfZeema^gma^nii^k!@dc%lni"Zg]maêhp^k !@dc%bg_"\aZkZ\m^kblmb\oZen^l!ma^2.Zg]._kZ\mbeôZen^lk^li^\mboêr"lahne][^^lmZ[ebla^]' Mablikh\^]nk^blg^\^llZkrhgerpa^gma^\h^_Ë\b^gmh_oZkbZmbhg!6*))tlmZg]Zk]]ôbZmbhg( f^Zg"bl`k^Zm^kmaZg*)'Bgm^kflh_i^kfZg^gmZ\mbhgl%oZkbZmbhglbgma^lê_&p^bàmh_\hg\k^m^ bg\hg\k^m^_kZf^lZk^\hglb]^k^]lfZee'

EC0: 4.1.2, 4.1.2 (3)

PD 6687[6]: 2.8.4


:m NEL pa^k^ ma^ oZkbZmbhg bl ghm lfZee% g@d%lni lahne] [^ nl^] pbma @dc%lni Zg] g@d%bg_ pbma @dc%bg_'LbfbeZker%pa^k^maôZkbZmbhgblghmlfZee%ZmLEL@dc%lnilahne][^nl^]pa^k^Z\mbhglZk^ ng_ZohnkZ[e^Zg]@dc%bg_nl^]pa^k^_ZohnkZ[e^' Pa^k^\a^\dl%ghmZ[er\a^\dlhglmZmb\^jnbeb[kbnf!>JN"%Zkô^krl^glbmbo^mhoZkbZmbhgh_ma^ fZ`gbmn]^h_Zi^kfZg^gmZ\mbhg_khfhgîeZ\^mhZghma^k%ma^_ZohnkZ[e^Zg]ng_ZohnkZ[e^ iZkmlh_mablZ\mbhglahne][^\hglb]^k^]Zlbg]bob]nZeZ\mbhgl'Bgln\aÂo^krl^glbmbo^Ão^kbË\Zmbhgl g@%lniZg]g@%bg_lahne][^nl^]'

EC0: 6.4.3 (4)

+'*) Load arrangements of actions: introduction Maîkh\^llh_]^lb`gbg`\hg\k^m^lmkn\mnk^lbgoheo^lb]^gmb_rbg`kêôZgm]^lb`glbmnZmbhglZg] ebfbmlmZm^l'Ma^l^bg\en]î^klblm^gm%mkZglb^gmhkZ\\b]^gmZelbmnZmbhgl'Bg^Z\a]^lb`glbmnZmbhg ma^lmkn\mnk^lahne][ô^kbË^]Zmma^kêôZgmebfbmlmZm^l'

EC0: 3.2

Bg ma^ ZgZerlbl h_ ma^ lmkn\mnk^ Zm ma^ ebfbm lmZm^ [^bg` \hglb]^k^]% ma^ fZqbfnf ^__^\m h_ Z\mbhgl lahne] [^ h[mZbg^] nlbg` Z k^Zeblmb\ ZkkZg`^f^gm h_ ehZ]l'@^g^kZeer oZkbZ[e^ Z\mbhgl lahne][^ZkkZg`^]mhikh]n\^ma^fhlmng_ZohnkZ[e^^__^\m%_hk^qZfie^mhikh]n\^fZqbfnf ho^kmnkgbg`fhf^gmlbgliZglhkfZqbfnf[^g]bg`fhf^gmlbglniihkml' ?hk [nbe]bg` lmkn\mnk^l% ]^lb`g \hg\^gmkZm^l fZbger hg ma^ NEL% ma^ nembfZm^ ebfbm lmZm^ h_ lmk^g`ma!LMK"%Zg]LEL%ma^l^kob\^Z[bebmrebfbmlmZm^'Ahpô^k%bmbl^ll^gmbZemaZmZeeebfbmlmZm^l Zk^\hglb]^k^]'MaêbfbmlmZm^lh_^jnbeb[kbnf!>JN"%lmk^g`maZmNELpbma`^hm^\agb\ZeZ\mbhgl !LMK(@>H"Zg]Z\\b]^gmZelbmnZmbhglfnlm[^mZd^gbgmhZ\\hngmZlZiikhikbZm^'

EC0: 3.3, 3.4, 6.4, 6.5

+'** Load arrangements according to the UK National Annex to Eurocode Bg[nbe]bg`lmkn\mnk^l%Zgrh_ma^_heehpbg`l^mlh_lbfiebË^]ehZ]ZkkZg`^f^gmlfZr[^nl^]Zm NELZg]LEL!L^^?b`nk^+'0"'

Cl. 5.1.3 & NA

N Ma^fhk^\kbmb\Zeh_3

Z"Zem^kgZm^liZgl\Zkkrbg`g@@d$gJJdpbmahma^kliZglehZ]^]pbmag@@d4Zg] ["ZgrmphZ]cZ\^gmliZgl\Zkkrbg`g@@d$gJJdpbmahma^kliZglehZ]^]pbmag@@d' N Hkma^fhk^\kbmb\Zeh_3

Z"Zem^kgZm^liZgl\Zkkrbg`g@@d$gJJd4pbmahma^kliZglehZ]^]pbmag@@d4Zg] ["ZeeliZgl\Zkkrbg`g@@d$gJJd' N Hk%_hkleZ[lhger%ZeeliZgl\Zkkrbg`g@@d$g@@d%ikhob]^]ma^_heehpbg`\hg]bmbhglZk^f^m3 L BgZhg^&pZrliZggbg`leZ[ma^Zk^Zh_^Z\a[Zr^q\^^]l,)f+!Z[Zrbl]^_bg^]ZlZ

lmkbiZ\khllma^_neepb]mah_Zlmkn\mnk^[hng]^]hgma^hma^klb]^l[rebg^lh_lniihkm"' L M a^kZmbhh_maôZkbZ[e^Z\mbhg%Jd%mhmaî^kfZg^gmZ\mbhg%@d%]h^lghm^q\^^]*'+.' L Ma^fZ`gbmn]^h_maôZkbZ[e^Z\mbhg^q\en]bgìZkmbmbhgl]h^lghm^q\^^].dG(f+'

Pa^k^ZgZerlblbl\Zkkb^]hnm_hkma^lbgèêhZ]\Zl^h_ZeeliZglehZ]^]%ma^k^lnembg`fhf^gml% ^q\îm mahl^ Zm \Zgmbeô^kl% lahne] [^ k^]n\^] [r +)% pbma Z \hgl^jn^gmbZe bg\k^Zl^ bg ma^ liZgfhf^gml'

25

g JJ d g JJ d

g @@ d

g JJ d g @ @ d g JJ d

a) Alternate spans loaded

b) Adjacent spans loaded

g @@ d

c) All spans loaded


Ghm^ Pabelmma^nl^h_>qi'!/'*)"blbg]b\Zm^]%ma^l^ZkkZg`^f^gmlfZr^jnZeer[^nl^]pbma>qi'!/'*)Z" hk!/'*)["' ?b`nk^+'0 EhZ]ZkkZg`^f^gml_hk[^ZflZg]leZ[lZ\\hk]bg`mhNDG:mh>nkh\h]^

26

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml +'*+ Examples of loading Ikhc^\m]^mZbel

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

Continuous beam in a domestic structure

CCIP – 041 1 Oct 09

2.12.1 Continuous beam in a domestic structure


Determine the appropriate load combination and ultimate load for a continuous beam of four 6 m spans in a domestic structure supporting a 175 mm slab at 6 m centres. qk gk A

6000 mm

B

6000 mm

C

6000 mm

D

6000 mm

E

Figure 2.8 Continuous beam in a domestic structure a) Actions Permanent action, gk Self-weight, 175 mm thick slabs : 0.17 x 25 x 6.0 E/o self-weight downstand 800 × 225 : 0.80 x 0.225 x 25 50 mm screed @ 22 kN/m3 : 0.05 x 22 x 6.0 Finishes and services : 0.50 x 6.0 Dividing wall 2.40 × 4.42 (200 mm dense blockwork with plaster both sides) Total gk Variable action, qk Imposed, dwelling @ 1.5 kN/m2 : 1.5 x 6.0 Total

= 26.3 = 4.5 = 6.6 = 3.0 = 10.6 = 51.0

= qk =

Ultimate load, n Assuming use of Exp. (6.10), n = 1.35 × 51 + 1.5 × 9.0 = Assuming use of worst case of Exp. (6.10a) or Exp. (6.10b) Exp. (6.10a): n = 1.35 × 51 + 0.7 × 1.5 × 9.0 = Exp. (6.10b): n = 1.25 × 51 + 1.5 × 9.0 = In this case Exp. (6.10a) would be critical‡ =ultimate load

‡

kN/m

9.0 9.0

= 82.4 = 78.3 = 77.3 = 78.3

This could also be determined from Figure 2.5 or by determining that gk > 4.5qk

27

Ikhc^\m]^mZbel

Continuous beam in mixed use structure

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

2.12.2 Continuous beam in mixed use structure Determine the worst case arrangements of actions for ULS design of a continuous beam supporting a 175 mm slab @ 6 m centres. Note that the variable actions are from two sources as defined in Figure 2.9.:


qk1 = 15 kN/m

qk2 = 24 kN/m gk = 51 kN/m

A

6000 mm

B

6000 mm

C

6000 mm

D

6000 mm

E

Office use @ 2.5 kN/m2

Shopping use @ 4.0 kN/m2

c0 = 0.7

c0 = 0.7

Figure 2.9 Continuous beam in mixed-use structure

a) Load combination Load combination Exp. (6.10a) or Exp. (6.10b) will be used, as either will produce a smaller total load than Exp. (6.10). It is necessary to decide which expression governs. i) Actions Permanent action As before, Example 2.12.1 Variable action Office @ 2.5 kN/m2 Shopping @ 4.0 kN/m2 Ultimate load, n For office use: Exp. (6.10a): n = 1.35 × 51 + 0.7 × 1.5 × 15.0 Exp. (6.10b): n = 1.25 × 51 + 1.5 × 15.0 For shopping use: Exp. (6.10a): n = 1.35 × 51 + 1.5 × 0.7 × 24.0 Exp. (6.10b): n = 1.25 × 51 + 1.5 × 24.0 By inspection Exp. (6.10b) governs in both cases‡

kN/m gk

= 51.0

qk1 qk2

= 15.0 = 24.0

= 84.6 = 86.3 = 94.1 = 99.8

b) Arrangement of ultimate loads As the variable actions arise from different sources, one is a leading variable action and the other is an accompanying variable action. The unit loads to be used in the various arrangements are: ‡ This could also be determined from Figure 2.5 or by determining that g > 4.5q k k

28

CCIP – 041 1 Oct 09

EC1-1-1: 6.3.1.1 & NA, EC0: A.1.2.2. & NA


:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml i) Actions Permanent 1.25 × 51.0 Variable Office use as leading action, gQQk = 1.5 × 15 as accompanying action, c0gQQk = 0.7 × 1.5 × 15 Shopping use as leading action, gQQk = 1.5 × 24 as accompanying action, c0gQQk = 0.7 × 1.5 × 24

kN/m = 63.8

= 22.5 = 15.75

= 36.0 = 25.2

ii) For maximum bending moment in span AB

The arrangement and magnitude of actions of loads are shown in Figure 2.10. The variable load in span AB assumes the value as leading action and that in span CD takes the value as an accompanying action. Leading variable action gQ q k1 = 22.5 kN/m

A

B

Accompanying Permanent variable action action c Q g Q q k2 = 25.2 kN/m gG g k = 63.8 kN/m

C

D

E

Figure 2.10 For maximum bending moment in span p AB

iii) For maximum bending moment in span CD The load arrangement is similar to that in Figure 2.10, but now the variable load in span AB takes its value as an accompanying action (i.e. 15.75 kN/m) and that in span CD assumes the value as leading action (36 kN/m). Accompanying variable action c Qg Qq k1 = 15.8 kN/m

A

B

Leading variable action g Qq k2 = 36.0 kN/m

C

D

Permanent action gG,inf g k = 63.8 kN/m

E

Figure 2.11 For maximum bending moment in span p CD

29

iv) For maximum bending moment at support B

The arrangement of loads is shown in Figure 2.12. As both spans AB and BC receive load from the same source, no reduction is possible ( (other than that for large g area‡). ). Leading variable action gQ q k1 = 22.5 kN/m


A

B

EC1-1-1: 6.3.1.1 (10) & NA

Permanent action gG g k = 63.8 kN/m

C

D

E

Figure 2.12 For maximum bending moment at support pp B v) For maximum bending moment at support D The relevant arrangement of loads is shown in Figure 2.13. Comments made in d) also apply here. Leading variable action gQ q k2 = 36 kN/m

A

B

C

D

Permanent action gG g k = 63.8 kN/m

E

Figure 2.13 For maximum bending moment at support pp D vi) For critical curtailment and hogging in span CD The relevant arrangement of loads is shown in Figure 2.14. Accompanying p variable action c 0gQ q k1 = 15.8 kN/m

A

B

C

Leading variable action g Q q k2 = 36.0 kN/m Permanent actionn gG,in f g k = 51 kN/m m D

E

Figure 2.14 For curtailment and hogging in span p CD Eurocode 2 requires that all spans should be loaded with either gG,sup or gG,inff (as per Table 2.16). As illustrated in Figure 2.14, using gG,inff = 1.0 might be critical for curtailment and hogging in spans. spans

‡ Variable actions may be subjected to reduction factors: a , according to the A

area supported pp ((m2), aA = 1.0 – A/1000 ≥ 0.75.

30

Cl. 2.4.3(2)

EC1-1-1: 6.3.1.2 (10) & NA

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml Ikhc^\m]^mZbel

chg

Ch[gh'

Propped cantilever

web

La^^mgh'

TCC

=Zm^

2.12.3 Propped cantilever


Determine the Equilibrium, ULS and SLS (deformation) load combinations for the propped cantilever shown in Figure 2.15. The action P at the end of the cantilever arises from the permanent action of a wall. gk

qk

CCIP – 041 1 Oct 09

EC0: Table 1.2(B), Note 3

P

C A

B

Figure 2.15 Propped pp cantilever beam and loading For the purposes of this example, the permanent action P is considered to be from a separate source than the self-weight of the structure so both gG,sup and gG,inf need to be considered.

a) Equilibrium limit state (EQU) for maximum uplift at A 0.0qk = 0 gGinf gk= 0.9gk

gGk,sup P= 1.1P

1.5qk

A

B

C gGk,sup gk= 1.1gk

EC0: Table A1.2 (A) & NA EC0: 6.4.3.1 (4), Table A1.2 (A) & NA

p

b) Ultimate limit state (ULS) i) For maximum moment at B and anchorage of top reinforcement BA gGk,sup gk= 1.35gk

gQ qk= 1.5qk gGk,sup P= 1.35P

EC0: Tables A1.1, A1.2 (B) & NA

C A

B

Figure 2.17 ULS: maximum moment at B Notes gGk,inf gk = 1.0 gk may be critical in terms of curtailment of top bars BA.

31

ii) For maximum sagging moment AB gGk,sup P= P 1.1P

gQqk= 1.5qk gGk,sup gk= 1.35gk

C A

EC0: Table A1.1, A1.2 (B) & NA

B

Figure 2.18 ULS: maximum span p moment AB


Notes 1 Depending on the magnitude of gk, qk length AB and BC, gGk,inf gk (= 1.0 gk) may be more critical for span moment. 2 The magnitude of the load combination indicated are those for Exp. (6.10) of BS EN 1990. The worst case of Exp. (6.10a) and Exp. (6.10b) may also have been used. 3 Presuming supports A and B were columns then the critical load combination for Column A would be as Figure 2.18. For column B the critical load combination might be either as Figure 2.17 or 2.18.

c) Serviceability limit state (SLS) of deformation: (quasi-permanent loads) i) For maximum deformation at C 1.0c c2qk= 0.3*qk

1.0gk

1.0P

EC0: Tables A1.1, A1.2.2, A1.4 & NA

C A

B

*Assuming office area

Figure 2.19 SLS: maximum deformation at C

ii) For maximum deformation AB 1.0c c2qk= 0.3*qk

1.0P

1.0gk C A

B

* Assuming office area

Figure 2.20 SLS: maximum deformation AB Notes Quasi-permanent load combinations may also be used for calculations of crack widths or controlling cracking, i.e. the same load combinations as shown in Figures 2.19 and 2.20 may be used to determine SLS moment to determine stress in reinforcement. The characteristic and/or frequent combinations may be appropriate for other SLS limit states: for example, it is recommended that the frequent combination is used to determine whether a member has cracked or not.

32

:gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml Ikhc^\m]^mZbel

chg

Ch[gh'

Overall stability

web

La^^mgh'

TCC

=Zm^

CCIP-041 1 Oct 09

2.12.4 Overall stability (EQU)


For the frame shown in Figure 2.21, identify the various load arrangements to check overall stability (EQU) against overturning. Assume that the structure is an office block and that the loads qk2 and qk3 may be treated as arising from one source. qk1 gk1 qk2 gk2 wk

qk3 gk3

A

B

Figure 2.21 Frame configuration

a) EQU – Treating the floorr imposed load as the leading variable action Permanent action, P favourable 0.9gk1

Accompanying variable action = gQk co wk = 1.5 x 0.5 x wk

Accompanying variable actioon on = gQkco qk1 = 1.05qk1 Permanent action, unfavourable b = gGk,supgk1 = 1.1gk1

Permanent action, P favourable 0.9gk2

Lead variable action = gQk qk2 k2 = 1.5qk2 Permanent action, unfavourable b = gGk,supgk2 = 1.1gk2

Permanent action, P favourable 0.9gk3

Lead variable action = gQk qk3 k3 = 1.5qk3 Permanent action, unfavourable b = gGk,supgk3 = 1.1gk3

= 0.75 wk A

B

Figure 2.22 Frame with floor variable action as leading variable action

Tables 2.16 & 2.17

See Table 2.17 for values of c0

33

b) EQU – Treating the rooff imposed load as the leading variable action


0.75 wk

0.9gk1

1.5q k1 1.1gk1

0.9gk2

1.5 x 0.7 x q k2 = 1.05 q k2 1.1gk2

0.9gk3

A

Tables 2.16 & 2.17

1.5 x 0.7 x q k3 = 1.05 q k3 1.1gk3

B

Figure 2.23 Frame with roof variable action as leading variable actttion

c) EQU – Treating wind as the leading variable action

1.5 wk

0.9gk1

1.5 x 0.7 x q k1 = 1.05 q k1 1.1gk1

0.9gk2

1.5 x 0.7 x q k2 = 1.05 q k2 1.1gk2

0.9gk3

A

1.5 x 0.7 x q k3 = 1.05 q k3 1.1gk3

B

Figure 2.24 Frame with wind as lead variable action

34

Tables 2.16 & 2.17

,3LeZ[l

3 Slabs 3.0 General Ma^\Ze\neZmbhglbgmabll^\mbhgZkîk^l^gm^]bgma^_heehpbg`ln[&l^\mbhgl3


,'*:lbfierlniihkm^]hg^&pZrleZ[ ,'+ :\hgmbgnhnlhg^&pZrleZ[ ,', :\hgmbgnhnlkb[[^]leZ[ ,'-:[Zrh_ZÌZmleZ[ ,'.:lmZbkÌbàm' Ma^l^\Ze\neZmbhglZk^bgm^g]^]mhlahppaZmfbàm[^]^^f^]mrib\ZeaZg]\Ze\neZmbhgl'Ma^r Zk^ beenlmkZmbo^ h_ ma^G*22+¾*¾*'Ma^ÌZmleZ[\Ze\neZmbhgbllniie^f^gm^][rZ\hff^gmZkr' :`^g^kZef^mah]h_]^lb`gbg`leZ[lbllahpg[êhp' N =^m^kfbg^]^lb`geb_^'

EC0 & NA Table NA.2.1

N :ll^llZ\mbhglhgma^leZ['

EC1 & NA

N :ll^ll]nkZ[bebmrk^jnbk^f^gmlZg]]^m^kfbg^

Table 4.1 BS 8500-1: Tables A4 & A5

\hg\k^m^lmk^g`ma' N
k^lblmZg\î^kbh]' N
EC2-1-2: Tables 5.8, 5.9, 5.10 & 5.11 Cl. 4.4.1

[hg]k^jnbk^f^gml' N =^m^kfbg^pab\a\hf[bgZmbhglh_Z\mbhglZiier'

EC0 & NA Tables NA.A1.1 & NA.A1.2 (B)

N =^m^kfbgêhZ]bg`ZkkZg`^f^gml'

Cl. 5.1.3(1) & NA

N :gZerl^lmkn\mnk^mhh[mZbg\kbmb\Zefhf^gmlZg]la^Zk

Cl. 5.4, 5.5, 5.6

_hk\^l' N =^lb`g_e^qnkZek^bg_hk\^f^gm'

Cl. 6.1

N
Cl. 7.4

N
Cl. 6.2

N Hma^k]^lb`g\a^\dl3

Cl. 9.3.1.1(1), 9.2.1.1(1) Cl. 7.3, Tables 7.2N & 7.3N Cl. 9.3.1.2(2) Cl. 9.3.1.1(2), 9.3.1.4(1)

N
Cl. 9.3.1.1(4), 9.2.1.3, Fig. 9.2

N
Cl. 9.3.1.2, 8.4.4, 9.3.1.1(4) Cl. 9.2.1.5(1), 9.2.1.5(2)

N
Cl. 8.7.3

35

3.1 Simply supported one-way slab


Mabl\Ze\neZmbhgblbgm^g]^]mhlahpZmrib\Ze[Zlb\aZg]\Ze\neZmbhg' Ikhc^\m]^mZbel

chg

Ch[gh'

Simply supported one-way slab

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

A 175 mm thick slab is required to support screed, finishes, an office variable action of 2.5 kN/m2 and demountable partitions (@ 2 kN/m). The slab is supported on load-bearing block walls. fck = 30 MPa, fyk = 500 MPa. Assume a 50-year design life and a requirement for 1 hour resistance to fire. qk = 3.3 kN/m2 gk = 5.9 kN/m2 4800

Figure 3.1 Simply p supported pp one-way slab

3.1.1 Actions

kN/m2

Permanent: Self-weight 0.175 × 25 50 mm screed Finishes, services

EC1-1-1: Table A1

Total

= 4.4 = 1.0 = 0.5 gk = 5.9

Total

= 2.5 = 0.8 jk = 3.3

EC1-1-1: Tables 6.1, 6.2 & NA EC1-1-1: 6.3.12(8)

Variable: Offices, general use B1 Movable partitions @ 2.0 kN/m

3.1.2 Cover Nominal cover, cnom: cnom = cmin + Dcdev

Exp. (4.1)

where cmin = max[cmin,b ; cmin,dur] where cmin,b

Cl. 4.4.1.2(3) = minimum cover due to bond = diameter of bar

Assume 12 mm main bars. cmin,dur = minimum cover due to environmental conditions Assuming XCI and using C30/37 concrete, cmin,dur = 15 mm Dcdev = allowance in design for deviation. Assuming no measurement of cover, Dcdev = 10 mm = cnom = 15 + 10 = 25 mm 36

Table 4.1. BS 8500-1: Table A4. Cl. 4.4.1.2(3)

,'*3Lbfierlniihkm^]hg^&pZrleZ[

Fire: Check adequacy of section for 1 hour fire resistance (i.e. REI 60). Thickness, hs,min = 80 mm cf. 175 mm proposed = OK Axis distance, amin = 20 mm cf. 25 + f/2 = 31 i.e. not critical = OK

EC2-1-2: 4.1(1), 5.1(1) & Table 5.8

= choose cnom = 25 mm


3.1.3 Load combination (and arrangement) Ultimate load, n: By inspection, BS EN 1990 Exp. (6.10b) governs = n = 1.25 × 5.9 + 1.5 × 3.3 = 12.3 kN/m2

Fig. 2.5 ECO: Exp. (6.10b)

3.1.4 Analysis Design moment: MEd = 12.3 × 4.82/8 = 35.4 kNm Shear force: V = 12.3 × 4.8/2 = 29.5 kN/m

3.1.5 Flexural design Effective depth: d = 175 − 25 − 12/2 = 144 mm Flexure in span: K = MEd/bd2fck = 35.4 × 106/(1000 × 1442 × 30) = 0.057 z/d = 0.95 z = 0.95 × 144 = 137 mm As = MEd/fydz = 35.4 × 106/(137 × 500/1.15) = 594 mm2/m (r = 0.41%)

Fig. 3.5 Appendix A1 Table C5

Try H12 @ 175 B1 (645 mm2/m)

3.1.6 Deflection Check span-to-effective-depth ratio. Basic span-to-effective-depth ratio for r = 0.41% = 20 As,prov/As,req = 645/599 = 1.08 Max. span = 20 × 1.08 × 144 = 3110 mm i.e. < 4800 mm Consider in more detail: Allowable l/d = N × K × F1 × F2 × F3 where N = 25.6 (r = 0.41%, fck = 30 MPa) K = 1.0 (simply supported) F1 = 1.0 (beff/bw = 1.0) F2 = 1.0 (span < 7.0 m) F3 = 310/ ss © 1.5

Appendix B Table 7.4N & NA Exp. (7.17) = no good

Cl. 7.4.2, Appendix C7, Tables C10-C13

37

where‡ ss = ssu (As,reqq/As,prov) 1/d where ssu { 242 MPa (From Figure C3 and gk/qk = 1.79, c2 = 0.3, gG = 1.25) d = redistribution ratio = 1.0 = ss { 242 × 594/645 = 222 = F3 = 310/222 = 1.40 © 1.5


= Allowable l/ l d = 25.6 × 1.40 = 35.8 Actual l/ l d = 4800/144 = 33.3

Cl. 7.4.2, Exp. (7.17) Table 7.4N, & NA Table NA.5: Note 5 Figure C3 Figure C3

= OK

Use H12 @ 175 B1 (645 mm2/m)

3.1.7 Shear By inspection, OK However, if considered critical: V = 29.5 kN/m as before VEd = 29.5 – 0.14 × 12.3 = 27.8 kN/m vEd = 27.8 × 103/144 × 103 = 0.19 MPa vRd,c = 0.53 MPa

Cl. 6.2.1(8) Cl. 6.2.2(1); Table C6

= No shear reinforcement required q

3.1.8 Summary of design

H12 @ 175

Figure 3.2 Simply p supported pp slab: summary

3.1.9 Detailing checks It is presumed that the detailer would take the design summarised above and detail the slab to normal best practice, e.g. to SMDSC[9] or to How to design concrete structures using Eurocode 2 2,[8] Chapter 10, Detailing. This would usually include dimensioning and detailing curtailment, laps, U-bars and also undertaking the other checks detailed below. See also 3.2.10 detailing checks for a continuous one-way slab. a) Minimum areas Minimum area of reinforcement: As,min = 0.26 (ffctm/ffyk) bt] ª 0.0013 btd where bt = width of tension zone fctm = 0.30 × fck0.666 ‡

38

See Appendix B1.5

Cl. 9.3.1.1, 9.2.1.1 Table 3.1

,'*3Lbfierlniihkm^]hg^&pZrleZ[ LeZ[l

As,min = 0.26 × 0.30 × 300.666 × 1000 × 144/500 = 216 mm2/m (r r = 0.15%) = H12 @ 175 B1 OK Crack control: OK by inspection. Maximum spacing of bars: < 3h < 400 mm

Table 7.2N & NA OK

Cl. 9.3.1.1.(3)


Secondary reinforcement: 20% As,reqq = 0.2 × 645 = 129 mm2/m Use H10 @ 350 (224) B2 Edges: effects of assuming partial fixity along edge Top steel required = 0.25 × 594 = 149 mm2/m Use H10 @ 350 (224) T2 B2 as U-bars extending 960 mm into slab§ b) Curtailment Curtailment main bars: Curtail main bars 50 mm from or at face of support.

At supports: 50% of As to be anchored from face of support.

Cl. 9.3.1.1.(2) Cl. 9.3.1.2.(2)

SMDSC[9]: Fig. 6.4; How to[8]: Detailing Cl. 9.3.1.2.(1)

Use H12 @ 350 B1 T1 U-bars In accordance with SMDSC[9] detail MS3 lap U-bars 500 mm with main steel, curtail T1 leg of U-bar 0.1ll (= say 500 mm) from face of support.

§A

free unsupported edge is required to use ‘longitudinal and transverse reinforcement’ generally using U-bars with legs at least 2h long. For slabs 150 mm deep or greater, SMDSC[9] standard detail recommends U-bars lapping 500 mm with bottom steel and extending 0.1ll top into span.

Cl. 9.3.1.4.(1)

39

3.2 Continuous one-way solid slab


Mabl\Ze\neZmbhgblbgm^g]^]mhlahpbg]^mZbemaîkhoblbhglh_]^lb`gbg`ZleZ[mh>nkh\h]^+ nlbg`^ll^gmbZeerma^lZf^leZ[Zlnl^]bg>qZfie^,'*' Ikhc^\m]^mZbel

chg

Ch[gh'

Continuous one-way solid slab

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

A 175 mm thick continuous slab is required to support screed, finishes, an office variable action of 2.5 kN/m2 and demountable partitions (@ 2 kN/m). The slab is supported on 200 mm wide load-bearing block walls at 6000 mm centres. fck = 30, fyk = 500 and the design life is 50 years. A fire resistance of 1 hour is required.

qk = 3.3 kN/m2 gk = 5.9 kN/m2

200

5800

200

5800

Figure 3.3 Continuous solid slab

3.2.1 Actions kN/m2

Permanent: As Section 3.1.1

gk = 5.9

Variable: As Section 3.1.1

jk = 3.3

EC1-1-1: 6.3.1.2(8)

3.2.2 Cover Nominal cover, cnom: As Section 3.1.2

cnom = 25 mm

3.2.3 Load combination (and arrangement) Ultimate action (load): As Section 3.1.3, BS EN 1990 Exp. (6.10b) governs = n = 1.25 × 5.9 + 1.5 × 3.3 = 12.3 kN/m2

Fig. 2.5 EC0: Exp. (6.10b)

3.2.4 Analysis Clear span, ln a1 = min[h/2; t/2] = min[175/2; 200/2] a2 = min[h/2; t/2] = min[175/2; 200/2] leff

40

= 5800 mm = 87.5 mm = 87.5 mm = 5975 mm

Cl. 5.3.2.2(1)

,'+3
Bending moment: End span 1st internal support


Internal spans and supports

MEd = 0.086 × 12.3 × 5.9752

= 37.8 kNm/m

5.9752

= 37.8 kNm/m

MEd = 0.086 × 12.3 ×

MEd = 0.063 × 12.3 ×

5.9752

Cl. 5.1.1(7) Table C2

= 27.7 kNm/m

Shear: End support

VEd = 0.40 × 12.3 × 5.975

= 29.4 kN/m

1st interior support

VEd = 0.60 × 12.3 × 5.975

= 44.1 kN/m

3.2.5 Flexural design: span a) End span (and 1st internal support) Effective depth, d: d = h − cnom − f/2 = 175 − 25 − 12/2 = 144 mm Relative flexural stress, K: K = MEd/bd2fck = 37.8 × 106/1000 × 1442 × 30 = 0.061 K' = 0.207 or restricting x/d to 0.45 K' = 0.168 = by inspection, section is under-reinforced (i.e. no compression reinforcement required). Lever arm, z: z = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d‡ = (144/2) [1 + (1 − 3.53 × 0.061)0.5] = 0.945d = 136 mm

Appendix A1

Fig. 3.5 Appendix A1

Area of steel, As: As = MEd/fydz = 37.8 × 106/(500/1.15 × 136) = 639 mm2/m (r = 0.44%) Try H12 @ 175 B1 (645 mm2/m) b) Internal spans and supports Lever arm, z: By inspection, z = 0.95d = 0.95 × 144 = 137 mm

Fig. 3.5 Appendix A1

Area of steel, As: As = MEd/fydz = 27.7 × 106/(500/1.15 × 137) = 465 mm2/m (r = 0.32%) Try H12 @ 225 B1 (502 mm2/m) ‡

Designers may choose to use another form of this equation: z/d = 0.5 + (0.25 − 0.882K)0.5 ≤ 0.95

41

3.2.6 Deflection: end span Check end span-to-effective-depth ratio. Allowable l/d d = N × K × F1 × F2 × F3

Appendix B

where N = basic effective depth to span ratio: r = 0.44% r0 = fck0.5 × 10−3 = 0.55% = use Exp. (7.16a)


1.5fck0.5

3.2fck0.5

Cl. 7.4.2(2)

1)1.5

N = 11 + r0/r r+ (r0/r r− 0.5 = 11 + 1.5 × 30 × 0.55/0.44 + 3.2 × 300.5 (0.55/0.44 – 1)1.5 = 11.0 + 10.3 + 2.2 = 23.5

Exp. (7.16a)

K = structural system factor = 1.3 (end span of continuous slab)

Cl. 7.4.2

F1 = flanged section factor = 1.0 (beff/bw = 1.0)

Cl. 7.4.2

F2 = factor for long spans associated with brittle partitions = 1.0 (span < 7.0 m) F3 = 310/ ss ≤ 1.5

Cl. 7.4.2

where‡ ss = (ffyk/ gS) (As,reqq/As,prov) (SLS loads/ULS loads (1/d) = fyd × (As,reqq/As,prov) × (gk + c2 qk)/(g gGgk + gQqk) (1/d) = (500/1.15) × (639/645) × [(5.9 + 0.3 × 3.3)/12.3] × 1.08§ = 434.8 × 0.99 × 0.56 × 1.08 = 260 MPa F3 = 310/260 = 1.19 Note: As,prov/As,req ≤ 1.50

Allowable l/d d = N × K × F1 × F2 × F3 = 23.5 × 1.3 × 1.0 × 1.19 = 36.4 Max. span = 36.4 × 144 = 5675 mm, i.e. < 5795 mm

= No good

Try increasing reinforcement to H12 @ 150 B1 (754 mm2/m) ss = 434.8 × 639/754 × 0.56 × 1.08 = 223 F3 = 310/223 = 1.39 Allowable l/d d = 23.5 × 1.3 × 1.0 × 1.39 = 42.5

42

‡

See Appendix B1.5

§

The use of Table C3 implies certain amounts of redistribution, which are defined in Table C14.

Cl. 7.4.2, Exp. (7.17) Table 7.4N & NA, Table NA.5: Note 5 Exp. (7.17) EC0: A1.2.2 Table C14

Table 7.4N & NA, Table NA.5: Note 5

,'+3
Max. span = 42.5 × 144 = 6120 mm, i.e. > 5795 mm OK 2 = H12 @ 150 B1 (754 mm /m) OK

3.2.7 Deflection: internal span


Check internal span-to-effective-depth ratio. Allowable l/d = N × K × F1 × F2 × F3 where N = basic effective depth to span ratio: r = 0.32% r0 = fck0.5 × 10−3 = 0.55% = use Exp. (7.16a) 1.5fck0.5

3.2fck0.5

1)1.5

N = 11 + r0/r r+ (r0/r r− = 11 + 1.5 × 300.5× 0.55/0.32 + 3.2 × 300.5 (0.55/0.32 – 1)1.5 = 11.0 + 14.1 + 10.7 = 35.8

Cl. 7.4.2(2) Exp. (7.16a)

K = structural system factor = 1.5 (interior span of continuous slab)

Cl. 7.4.2

F1 = flanged section factor = 1.0 (beff/bbw = 1.0)

Cl. 7.4.2

F2 = factor for long spans associated with brittle partitions = 1.0 (span < 7.0 m)

Cl. 7.4.2

F3 = 310/ ss ≤ 1.5

where ss = fyd × (As,reqq/As,prov) × (gk + c2 qk)/(g gGgk + gQqk) (1/d) = (500/1.15) × (465/502) × [(5.9 + 0.3 × 3.3)/12.3] × 1.03 = 434.8 × 0.93 × 0.56 × 1.03 = 233 MPa

Cl. 7.4.2, Exp. (7.17), Table 7.4N & NA, Table NA.5 Note 5. Exp. (7.17) EC0: A1.2.2 Table C14

F3 = 310/233 = 1.33 Allowable l/d d = N × K × F1 × F2 × F3 = 35.8 × 1.5 × 1.0 × 1.33 = 71.4 Max. span = 71.4 × 144 = 10280 mm i.e. > 5795 mm OK Use H12 @ 225 B1 (502 mm2/m) in internal spans p

3.2.8 Shear Design shear force, VEd: At d from face of end support, VEd= 29.4 – (0.144 + 0.0875) × 12.3 = 26.6 kN/m

Cl. 6.2.1(8)

At d from face of 1st interior support, VEd = 44.1 − (0.144 + 0.0875) × 12.3 = 41.3 kN/m Shear resistance, VRd,c: VRd,c = (0.18/ gC)k(100 rl fck)0.333 bwd ≥ 0.0035kk1.5fck0.5bwd

Cl. 6.2.2(1)

43


where k = 1 + (200/d)0.5 ≤ 2.0 as d < 200 mm k = 2.0 rl = Asl/bd Assuming 50% curtailment (at end support) = 50% × 754/(144 × 1000) = 0.26% VRd,c = (0.18/1.5) × 2.0 × (100 × 0.26/100 × 30)0.33 × 1000 × 144 = 0.12 × 2 × 1.97 × 1000 × 144 = 0.47 × 1000 × 144 = 68.1 kN/m But VRd,cmin = 0.035k1.5fck0.5 bwd where k = 1 + (200/d)0.5 ≤ 2.0; as before k = 2.0 VRd,cmin = 0.035 × 21.5 × 300.5 × 1000 × 144 = 0.54 × 1000 × 144 = 77.6 kN/m = VRd,c = 77.6 kN/m = OK, no shear reinforcement required at end or 1st internal supports = H12 @ 150 B1 & H12 @ 175 T1 OK By inspection, shear at other internal supports OK.

3.2.9 Summary of design H12 @ 175 fck = 30 MPa P cnom = 25 mm H12 @ 150

H12 @ 225

Figure 3.4 Continuous solid slab: design summary Commentary It is usually presumed that the detailer would take the design summarised above together with the general arrangement illustrated in Figure 3.3 and detail the slab to normal best practice. The detailer’s responsibilities, standards and timescales should be clearly defined but it would be usual for the detailer to draw and schedule not only the designed reinforcement but all the reinforcement required to provide a compliant and buildable solution. The work would usually include checking the following aspects and providing appropriate detailing : t Minimum areas t Curtailment lengths t Anchorages 44

,'+3

t Details and sections The determination of minimum reinforcement areas, curtailment lengths, anchorages and laps using the principles in Eurocode 2 is shown in detail in the following calculations. In practice these would be determined from published tables of data or by using reference texts[8, 9]. Nonetheless the designer should check the drawing for design intent and compliance with standards. It is therefore necessary for the designer to understand and agree the principles of the detailing used.

3.2.10 Detailing checks a) Minimum areas Minimum area of longitudinal tension (flexural) reinforcement As,min = 0.26(ffctm/ffyk) btd ≥ 0.0013 btd where bt = width of tension zone fctm = 0.30 × fck0.667 As,min = 0.26 × 0.30 × 300.6677 × 1000 × 144/500 = 216 mm2/m (r r = 0.15%) = H12 @ 225 B1 OK Secondary (transverse reinforcement) Minimum 20% As,req 20% As,reqq = 0.2 × 502 = 100 mm2/m Consider As,min to apply as before. As,min = 216 mm2/m Try H10 @ 350 B2 (224 mm2/m)

Cl. 9.3.1.1, 9.2.1.1

Table 3.1

Cl. 9.3.1.1(2) SMDSC[9]

Check edge. Assuming partial fixity exists at edges, 25% of As is required to extend 0.2 × the length of the adjacent span.

Cl. 9.3.1.2(2)

As,reqq = 25% × 639 = 160 mm2/m As,min as before = 216 mm2/m = Use H10 @ 350 (224 mm2/m) U-bars at edges

Cl. 9.3.1.1, 9.2.1.1

45

Curtail 0.2 × 5975 = 1195 mm, say 1200 mm measured from face of support‡. Maximum spacing of bars Maximum spacing of bars < 3h < 400 mm

OK


Crack control As slab < 200 mm, measures to control cracking are unnecessary. However, as a check on end span: Loading is the main cause of cracking, = use Table 7.2N or Table 7.3N for wmax = 0.4 mm and ss = 241 MPa (see deflection check). Max. bar size = 20 mm or max. spacing = 250 mm = H12 @ 150 B1 OK. End supports: effects of partial fixity Assuming partial fixity exists at end supports, 15% of As is required to extend 0.2 × the length of the adjacent span. As,reqq = 15% × 639 = 96 mm2/m But, As,min as before = 216 mm2/m (r r = 0.15%) One option would be to use bob bars, but choose to use U-bars Try H12 @ 450 (251 mm2/m) U-bars at supports pp Curtail 0.2 × 5975 = say, 1200 mm measured from face of support.‡ b) Curtailment i) End span, bottom reinforcement Assuming end support to be simply supported, 50% of As should extend into the support. 50% × 639 = 320 mm2/m Try H12 @ 300 (376 mm2/m) at supports pp In theory, 50% curtailment of reinforcement may take place al from where the moment of resistance of the section with the remaining 50% would be adequate to resist the applied bending moment. In practice, it is usual to determine the curtailment distance as being al from where MEd = MEd,max/2.

‡Detail

MS2 of SMDSC[9], suggests 50% of T1 legs of U-bars should extend 0.3l (= say 1800 mm) from face of support by placing U-bars alternately reversed.

46

Cl. 9.3.1.2(2)

Cl. 9.3.1.1.(3) Cl. 7.3.3(1) Cl. 7.3.3(2), 7.3.1.5

Table 7.2N & interpolation, Table 7.3N & interpolation Cl. 9.3.1.2(2)

Cl. 9.3.1.1, 9.2.1.1

Cl. 9.3.1.2(2)

Cl. 9.3.1.2(1)

Cl. 9.3.1.2(1) Note, 9.2.1.3 (2)

,'+3
n

A

B


a) Load arrangement r

A

B

X MEd,max MEdx = RAX – nXX 2/2

b) Bending moment MEdx

A

B

lbd

987 633 lbd

MEdx /z TTensile force in reinforcement, Fs

TTensile resistance of reinforcement c) Tensile T force in bottom reinforcement 50% 50% A B 633 (say 500)

987 (say 850)

d) Curtailment of bottom reinforcement

Figure 3.5 Curtailment of bottom reinforcement: actions, bending moments, forces in reinforcement and curtailment Thus, for a single simply supported span supporting a UDL of n, MEd,max = 0.086nl 2; RA = 0.4nl At distance, XX, from end support, moment, MEd@XX = RAX – nX 2/2 = when M@XX = MEd,max/2: 0.086nl 2/2 = 0.4nlXX – nX 2/2 47


Assuming X = xl 0.043nl2 = 0.4nlxll – nxx2l2/2 0.043 = 0.4xx – x2/2 0 = 0.043 – 0.4xx + x2/2 x = 0.128 or 0.672, say 0.13 and 0.66 = at end support 50% moment occurs at 0.13 x span 0.13 × 5975 = 777 mm Shift rule: for slabs, al may be taken as d (= 144 mm), = curtail to 50% of required reinforcement at 777 – 144 = 633 mm from centreline of support. Say 500 mm from face of support pp A

Cl. 9.2.1.3(2), 6.2.2(5)

= in end span at 1st internal support 50% moment occurs at 0.66 × span 0.66 × 5975 = 3944 mm Shift rule: for slabs al may be taken as d (= 144 mm), = curtail to 50% of required reinforcement at 3944 + 144 = 4088 mm from support A or 5975 – 4088 = 987 mm from centreline of support B. Say 850 mm from face of support pp B

Cl. 9.2.1.3(2), 6.2.2(5)

ii) 1st interior support, top reinforcement Presuming 50% curtailment of reinforcement is required this may take place al from where the moment of resistance of the section with the remaining 50% would be adequate. However, it is usual to determine the curtailment distance as being al from where MEd = MEd,max/2.

Cl. 9.3.1.2(1) Note, 9.2.1.3(2)

Thus, for the 1st interior support supporting a UDL of n, MEd,maxTT = 0.086nl 2; RB = 0.6nl At distance Y from end support, moment, MEd@Y Y = MEd,maxTT – RAY + nY 2/2 = when M@Y Y = MEd,maxT /2 0.086nl 2/2 = 0.086nl 2 – 0.6nlY Y + nY 2/2 Assuming Y = yl 0.043nl 2 = 0.086nl 2 – 0.6nlyll + ny 2l 2/2 0 = 0.043 − 0.6yy + y 2/2 y = 0.077 (or 1.122), say 0.08 = at end support 50% moment occurs at 0.08 × span 0.08 × 5975 = 478 mm Shift rule: for slabs, al may be taken as d 144 mm = curtail to 50% of required reinforcement at 478 + 144 = 622 mm from centreline of support. 50% of reinforcement may be curtailed at, say, 600 mm from either face of support pp B 48

Cl. 9.2.1.3(2), 6.2.2(5)

,'+3

100% curtailment may take place al from where there is no hogging moment. Thus, when M@Y = MEd,maxT/2 0 = 0.086nl2 – 0.6nlY + nY2/2 Assuming Y = yl 0 = 0.086 – 0.6y + y2/2 y = 0.166 (or 1.034), say 0.17 = at end support 50% moment occurs at 0.17 × span 0.17 × 5975 = 1016 mm Shift rule: for slabs, al may be taken as d = curtail to 100% of required reinforcement at 1016 + 144 = 1160 mm from centreline of support. 100% of reinforcement may be curtailed at, say, 1100 mm from either face of support B. iii) Support B bottom steel at support At the support 25% of span steel required

0.25 × 639 = 160 mm2 As,min as before = 216 mm2/m For convenience use H12 @ 300 B1 (376 mm2/m) c) Anchorage at end support As simply supported, 50% of As should extend into the support. This 50% of As should be anchored to resist a force of FE = VEd × al/z where VEd = the absolute value of the shear force al = d, where the slab is not reinforced for shear z = lever arm of internal forces d = 30.9 kN/m FE = 29.4 × d/0.95‡ Anchorage length, lbd: lbd = alb,rqd ≥ lb,min where a = conservatively 1.0 lb,rqd = basic anchorage length required = (f/4) (ssd/fbd) where f = diameter of the bar = 12 mm ssd = design stress in the bar at the ultimate limit state = FE/As,prov = 30.9 × 1000/376 = 81.5 MPa ‡

Cl. 9.3.1.1(4), 9.2.1.5(1), 9.2.1.4(1) Cl. 9.3.1.1, 9.2.1.1

Cl. 9.2.1.2(1) & Note, 9.2.1.4(2) Exp. (9.3)

Cl. 9.2.1.3(2)

Cl. 8.4.4 Exp. (8.4)

Exp. (8.3)

Maximum z = 0.947 at mid-span and greater towards support. 49

fbd where n1


n2 fct,d

= ultimate bond stress = 2.25 n1 n2 fct,d

Cl. 8.4.2(2)

= 1.0 for ‘good’ bond conditions and 0.7 for all other conditions = 1.0 = 1.0 for bar diameter ≤ 32 mm = design tensile strength = act fct,k/ gC. For fck = 30 MPa = 1.0 × 2.0/1.5 = 1.33 MPa

Cl. 3.1.6(2) & NA, Tables 3.1 & 2.1N

=f[] = 2.25 × 1.33 = 3.0 MPa lb,rqd = (12/4) (81.5/1.33) = 183 mm lb,min = max(10d, 100 mm) = 120 mm lbd = 183 mm measured from face of support By inspection, using U-bars, OK d) Laps Lap H12 @ 300 U-bars with H12 @ 150 straights. Tension lap, l0 = a1 a2 a3 a5 a6 lb,rqd a l0min where a1 = 1.0 (straight bars) a2 = 1 − 0.15 (cd − f)/f where cd = min(pitch, side cover or cover) = 25 mm f = bar diameter = 12 mm a2 = 0.84 a3 = 1.0 (no confinement by reinforcement) a5 = 1.0 (no confinement by pressure) a6 = 1.5 lb,rqd = (f/4) ssd/fbd where ssd = the design stress at ULS at the position from where the anchorage is measured. Assuming lap starts 500 mm from face of support (587.5 mm from centreline of support): MEd = 29.5 × 0.59 − 12.3 × 0.592/2 = 15.2 kNm ssd = MEd /(Asz) = 15.2 × 106/(376 × 144/0.95) = 267 MPa fbd = ultimate bond stress = 2.25 n1 n2 fct,d 50

Exp. (8.6) Fig. 9.3

Exp. (8.10) Table 8.2

Fig. 8.4

Table 8.2

Table 8.3 Exp. (8.3)

Cl. 8.4.2(2)

,'+3
where n1 = 1.0 for ‘good’ conditions n2 = 1.0 for f < 32 mm fct,d = act fct,k/gC where act = 1.0 fct,k = 2.0 gC = 1.5 =f[] = 2.25 × 2.0/1.5 = 3.0 MPa


lb,rqd

Cl. 3.1.6 (2) & NA Table 3.1 Table 2.1N & NA

= (f/4) ssd/fbd = (12/4) × (267/3) = 267 mm

l0min b = max[0.3 a6 lb,rqd; 15f/ 200 mm] = max[0.3 × 1.5 × 229; 15 × 12; 200] = max[124; 180; 200] = 200 mm = l0 = a1 a2 a3 a5 a6 lb,rqd ≥ l0min = 1.0 × 0.84 × 1.0 × 1.0 × 1.5 × 329 ≥ 200 = 414 mm But good practice suggests minimum lap of max[tension lap; 500] = lap with bottom reinforcement = 500 mm starting 500 from face of support.

Exp. 8.6

SMDSC[9]: MS2

3.2.11 Summary of reinforcement details A 1200 H12 U-bars @ 300

200

500 500

500

H12 @ 150

600

H12 @ 300 500 350

200 600 500 H12 @ 175 T1

H12 @ 225 350 500 200

A

Figure 3.6 Continuous solid slab: reinforcement details

1200

500

H10 @ 350 B2

Figure 3.7 Section A–A showing reinforcement details at edge 51


3.3 Continuous ribbed slab Ikhc^\m]^mZbel

Continuous ribbed slab

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

This continuous 300 mm deep ribbed slab has spans of 7.5 m, 9.0 m and 7.5 m and is required for an office to support a variable action of 5 kN/m2. It is supported on wide beams that are the same depth as the slab designed in Section 4.3. One hour fire resistance is required: internal environment. The ribs are 150 mm wide @ 900 mm centres. Links are required in span to facilitate prefabrication of reinforcement. Assume that partitions are liable to be damaged by excessive deflections. In order to reduce deformations yet maintain a shallow profile use fck = 35 MPa and fyk = 500 MPa. gk = 4.17 kN/m2 gk = 4.3 kN/m2 qk = 5.0 kN/m2 A

7500 550

1000

B

9000 1000

1000

C

D

7500 1000

550

Figure 3.8 Continuous ribbed slab example p Notes on ribbed slab design There are various established methods for analysing ribbed slabs and dealing with the solid areas: t Using UDLs simplifies the analysis and remains popular. One method is to ignore the weight of the solid part of the slab in the analysis of the ribbed slab. (The weight of the solid area is then added to the loads on the supporting beam). This ignores the minor effect the solid areas have on bending in the ribbed slab. t Alternatively the weight of the solid part of the slab is spread as a UDL over the whole span. This is conservative both in terms of moment and shears at solid/shear interfaces but underestimates hogging in internal spans. t The advent of computer analysis has made analysis using patch loads more viable and the resulting analysis more accurate. t The ribbed part of the slab may be designed to span between solid areas. (The ribs span d/2 into the solid areas, which are assumed to act as beams in the orthogonal direction.) However, having to accommodate torsions induced in supporting beams and columns usually makes it simpler to design from centreline of support to centreline of support. t Analysis programs can cope with the change of section and therefore change of stiffness along the length of the slab. Moments would be attracted to the stiffer, solid parts at supports. However, the difference in stiffness between the ribbed and the solid parts is generally ignored. 52

CCIP – 041 1 Oct 09

,',3
In line with good practice analysis, this example is carried out using centreline of support to centreline of support and patch loads‡. Constant stiffness along the length of the slab has been assumed. CL

CL A

100


300 A 200

550

1000

200

Figure 3.9 Long section through slab

150

750

150

Figure 3.10 Section A–A: section through ribbed slab

3.3.1 Actions Permanent: UDL kN/m2 Self-weight: kN/m2 Rib 0.15 × 0.2 × 25/0.9 = 0.833 Slope 2 × (1/2) × 0.2/10 × 0.2 × 25/0.9 = 0.112 Slab 0.1 × 2.5 = 2.500 Cross rib 0.19 × 0.71 × 0.2 × 25/(0.9 × 7.5) = 0.100 Total self-weight = 3.545 Ceiling Services Raised floor Total permanent actions gk

‡

≈ = = =

3.55 0.15 0.30 0.30

= 4.30

In this case, assuming the patch load analysis is accurate, taking the weight of solid area to be spread over the whole span would overestimate span and support moments by 6–8% and shears at the solid/rib interface by 8–9%. Ignoring the weight of the solid area in the analysis of this ribbed slab would lead to underestimates of span moments by 1%, support moments by 3% and no difference in the estimation of shear at the solid shear interface. The latter may be the preferred option. 53

Permanent: patch load Extra over solid in beam area as patch load (0.2 × 25 – 0.833) = 4.167 Variable Imposed Allowance for partitions Total variable action

gk ≈ 4.17 = 4.00* = 1.00* gk = 5.00


3.3.2 Cover Nominal cover, cnom: cnom = cmin + Dcdev where cmin = max(cmin,b ; cmin,dur) where cmin,b = minimum cover due to bond = diameter of bar. Assume 20 mm main bars and 8 mm links cmin,dur = minimum cover due to environmental conditions. Assuming XC1 and C30/37 concrete, cmin,durr = 15 mm Dcdev = allowance in design for deviation. Assuming no measurement of cover Dcdev = 10 mm = cnom

Exp. (4.1)

Cl. 4.4.1.2(3)

Table 4.1. BS 8500-1: Table A4 Cl. 4.4.1.2(3)

= 20 + 10 to main bars or = 15 + 10 to links = critical

Fire: Check adequacy of section for REI 60.

EC2-1-2: 5.7.5(1)

Minimum slab thickness, hs = 80 mm OK

EC2-1-2: Table 5.8

Axis distance required Minimum rib width or

bmin = 120 mm with a = 25 mm bmin = 200 mm with a = 12 mm

EC2-1-2: Table 5.6

= at 150 mm wide (min.) a = 20 mm By inspection, not critical. Use 25 mm nominal cover to links

3.3.3 Load combination and arrangement Ultimate load, n: By inspection, Exp. (6.10b) is critical nslab = 1.25 × 4.30 + 1.5 × 5.0 = 13.38 kN/m2 nsolid areas = 1.25 × (4.30 + 4.17) + 1.5 × 5.0 = 18.59 kN/m2

*Client requirements. See also BS EN 1991–1–1, Tables 6.1, 6.2, Cl. 6.3.2.1(8) & NA. 54

Fig. 2.5 EC0: Exp. (6.10b)

,',3
Arrangement: Choose to use all-and-alternate-spans-loaded.

Cl. 5.1.3(1) & NA option b

3.3.4 Analysis Analysis by computer, includes 15% redistribution at support and none in the span.§ 90.7 kNm/m

100

EC0: A1.2.2 & NA, 5.3.1 (6)

90.7 kNm/m

80


60 40 20 0 –20

A

B

C

D

–40 –60 – 65.3 kNm/m

–80

– 61.1 kNm/m

– 65.3 kNm/m

a) Elastic moments 100

77.1 kNm/m

80

77.1 kNm/m

60 40 20 0 –20

A

B

C

D

–40 –60 –80

–61.7 kNm/m

–55.9 kNm/m

–61.7 kNm/m

b) Redistributed envelope

Figure 3.11 Bending moment diagrams

§ Note 1: A ribbed slab need not be treated as discrete elements provided rib spacing ≤ 1500 mm, depth of the rib ≤ 4 × its width, the flange is > 0.1 × distance between ribs and transverse ribs are provided at a clear spacing not exceeding 10 × overall depth of the slab.

Note 2: As 7.5 m < 85% of 9.0 m, coefficients presented in Concise Eurocode 2[5] are not applicable. 55

80 42.5 kN/m

63.2 kN/m

63.5 kN/m

40 0 A

B

C

D

– 40 – 63.5 kN/m


– 80

– 63.2 kN/m

– 42.5 kN/m

At solid/rib interface: AB @ 550 mm from A = 20.4 kNm/m z 18.3 kNm/rib MEd (sagging) VEd = 32.5 kN/m z 29.3 kN/rib BA @1000 mm from B = 47.1 kNm/m z 42.4 kNm/rib MEd (hogging) = 45.4 kN/m z 40.9 kN/rib VEd BC @ 1000 mm from B = 43.0 kNm/m z 38.7 kNm/rib MEd (hogging) = 45.1 kN/m z 40.6 kN/rib VEd Symmetrical about centreline of BC.

3.3.5 Flexural design, span A–B a) Span A–B: Flexure MEd = 61.7 kNm/m = 55.5 kNm/rib K = MEd/bd 2fck where b = 900 mm d = 300 − 25 – 8 – 20/2 = 257 assuming 8 mm link at H20 in span fck = 35 MPa =K = 55.5 × 106/(900 × 2572 × 35) = 0.027 K' = 0.207 or restricting x/d to 0.45 K' = 0.168 K ≤ K' = section under-reinforced and no compression reinforcement required.

56

Appendix A1


,',3
z = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d = (257/2) (1 + 0.951) ≤ 0.95 × 257 = 251 ≤ 244 = z = 244 mm But z = d – 0.4x = x = 2.5(d − z) = 2.5(257 − 244) = 33 mm = By inspection, neutral axis is in flange As = MEd/fydz where _r] = 500/1.15 = 434.8 MPa = 55.5 × 106/(434.8 × 244) = 523 mm2/rib Try 2 no. H20/rib (628 mm2/rib) b) Span A–B: Deflection Allowable l/d = N × K × F1 × F2 × F3 where

Appendix A1

Appendix A1

Appendix C7

N = Basic l/d: check whether r > r0 and whether to use Exp. (7.16a) or Exp. (7.16b)

Cl. 7.4.2(2)

r0 = fck0.5/1000 = 350.5/1000 = 0.59% r = As/Ac‡ = As,req/[bwd + (beff – bw)hf] where

PD 6687[6]

bw = min. width between tension and compression chords. At bottom assuming 1/10 slope to rib: = 150 + 2 × (25 + 8 + 20/2)/10 = 159 mm r = 523/(159 ( 257 + (900 − 159) × 100) = 523/114963 = 0.45%

r < r0 = use Exp. (7.16a)

N = 11 + 1.5fck0.5r /r0 + 3.2fck0.5(r /r0 – 1)1.5]

Exp. (7.16a)

= 11 + 1.5 × 350.5 × 0.055/0.045 + 3.2 × 350.5 (0.055/0.045 – 1)1.5 = [11 + 10.8 + 2.0] = 22.8 K = (end span) 1.3

F1 = (beff /bw = 5.66) 0.8 F2 = 7.0/leff = 7.0/7.5 = (span > 7.0 m) 0.93 F3 = 310/ ss ≤ 1.5

Table 7.4N & NA, Table NA.5: Note 5 Cl. 7.4.2(2) Cl. 7.4.2, Exp. (7.17) & NA; Table NA.5

‡ Section 2.18 of PD 6687 [6] suggests that r in T-beams should be based on the area of concrete above the centroid of the tension steel.

57

where‡ ss = (fyk/gS) (As,req/As,prov) (SLS loads/ULS loads) (1/d) = 434.8(523/628) [ (4.30 + 0.3 × 5.0)/13.38] (65.3/61.7§) = 434.8 × 0.83 × 0.43 × 1.06 = 164 MPa


F3 = 310/ss = 310/164 = 1.89# but ≤ 1.5, therefore say 1.50 = Permissible l/d = 22.8 × 1.3 × 0.8 × 0.93 × 1.50 = 33.0 = OK Actual l/d = 7500/257 = 29.2 Use 2 no. H20/rib (628 mm2/rib) c) Support A (and D): flexure (sagging) at solid/rib interface Reinforcement at solid/rib interface needs to be designed for both moment and for additional tensile force due to shear (shift rule) MEd,max = 18.3 kNm/rib VEd,max = 29.3 kNm/rib At solid/rib interface As = MEd/fydz + DFtd /fyd where z = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d where K = MEd/bd2fck where b = 900 mm d = 300 − 25 – 8 – 25 − 20/2 = 232 assuming 8 mm links and H25B in edge beam fck = 30 = 18.3 × 106/(900 × 2322 × 35) = 0.011

‡ See

Appendix B1.5

§

In analysis, 15% redistribution of support moments led to redistribution of span moments: d = 61.7/65.3 = 0.94. #

Both As,prov/As,req and any adjustment to N obtained from Exp. (7.16a) or Exp. (7.16b) is restricted to 1.5 by Note 5 to Table NA.5 in the UK NA. Therefore, 310/ ss is restricted to 1.5.

58

Cl. 9.2.1.3.(2)

Cl. 9.2.1.3.(2), Fig. 9.2

,',3
25 cover 12 fabric 8 link 16 bar

16 bar 25 bar 8 link 25 cover


20 bar 8 link 25 cover

=z= = fyd = DFtd =

(232/2) (1 + 0.980) ≤ 0.95 × 232 230 ≤ 220 = z = 220 mm 434.8 MPa 0.5VEd (cot y – cot a)

where y = angle between the concrete compression strut and the beam axis. Assume cot y = 2.5 (as a maximum) a = angle between shear reinforcement and the beam axis. For vertical links, cot a = 0 DFtd = 1.25VEd = 1.25 × 29.3 = 36.6 kN As = 18.3 × 106/(434.8 × 220) + 36.6 × 103/434.8 = 191 + 84 mm2 = 275 mm2 =Try 1 no. H20 B in end supports*

Appendix A1

Cl. 6.2.3(7), Exp. (6.18) Cl. 6.2.3(1) Appendix A2 Appendix C, Table C6 Cl. 6.2.3(1)

d) Support B (and C) (at centreline of support) MEd = 77.1 kNm/m = 69.4 kNm/rib K = MEd/bd2fck where d = 300 − 25 cover − 12 fabric − 8 link − 20/2 = 245 K = 69.4 × 106/(900 × 2452 × 35) = 0.037 By inspection, K ≤ K' z = (245/2) [1 + (1 − 3.53 K)0.5] ≤ 0·95d = (245/2) (1 + 0.932) < 0.95d = 237 mm As = MEd/fydz = 69.4 × 106/434.8 × 237 = 673 mm2/rib

* An alternative method would have been to calculate the reinforcement required to resist MEd at the shift distance, al, from the interface. 59


e) Support B (and C): flexure (hogging) at solid/rib interface Reinforcement at solid/rib interface needs to be designed for both moment and for additional tensile force due to shear (shift rule). MEd,max = 42.4 kNm/rib max. VEd,max = 40.9 kNm/rib max. As = MEd/fydz + DFtd/fyd where z = (245/2) [1 + (1 − 3.53 K)0.5] ≤ 0·95d where K = MEd/bd2fck = 42.4 × 106/(150 × 2452 × 35) = 0.135 Check K ≤ K' K' = 0.168 for d = 0.85 (i.e. 15% redistribution) = Section under-reinforced: no compression reinforcement required = z = (245/2) (1 + 0.723) ≤ 232 = 211 mm fyd = 434.8 MPa DFtd = 0.5VEd (cot y – cot a) where y = angle between the concrete compression strut and the beam axis. Assume cot y = 2.5 (as a maximum) a = angle between shear reinforcement and the beam axis. For vertical links, cot a = 0 DFtd = 1.25VEd = 1.25 × 40.9 = 51.1 kN As = 42.4 × 106/(434.8 × 211) + 51.1 × 103/434.8 = 462 + 117 mm2 = 579 mm2/rib To be spread over beff where by inspection, beff = 900. =Centre of support more critical (679 mm2/rib required). Top steel may be spread across beff where beff = bw + beff1 + beff2 ≤ b = bw + 2 × 0.1 × 0.15 × (l1 + l2) = 150 + 0.03 × (7500 + 9000) ≤ 900 = 645 mm = Use 2 no. H16 above rib and 3 no. H12 between (741 mm2/rib) where 2 no. H16 and 2 no. H12 are within beff

3.3.6 Flexural design, span BC a) Span B–C: Flexure MEd = 55.9 kNm/m = 50.3 kNm/rib

60

Cl. 9.2.1.3.(2)

Cl. 9.2.1.3.(2)

Appendix C, Table C4 Appendix A

Cl. 6.2.3(7), Exp. (6.18) Cl. 6.2.3(1) Appendix A2; Table C6 Cl. 6.2.3(1)

Cl. 9.2.1.2(2) Cl. 5.3.2.1(3) Cl. 9.2.1.2(2), 5.3.2

,',3

K

= MEd/bd2fck = 50.3 × 106/900 × 2572 × 35 = 0.02 i.e. ≤ K’ (as before K’ = 0.168)

By inspection, z = 0.95d = 0.95 × 257 = 244 mm By inspection, neutral axis is in flange. As = MEd/fydz = 50.3 × 106/434.8 × 244 = 474 mm2 Try 2 no. H20/rib (628 mm2/rib) b) Span B–C: Deflection Allowable l/d = N × K × F1 × F2 × F3 where N = Basic l/d

Section C7 Cl. 7.4.2(2)

r = 474/(159 (× 257 + (900 − 159) × 100) = 474/114963 = 0.41% r0 = 0.59% (for fck = 30) = r < r0 use Exp. (7.16a) N = 11 + 1.5 fck0.5 r0/r + 3.2fck0.5 (r0/r – 1)1.5 = 11 + 1.5 ×

350.5

× 0.055/0.041 + 3.2 ×

350.5

Exp. (7.16a) (0.055/0.041 −

1)1.5

= 11 + 11.9 + 3.8 = 26.7 K = (internal span) 1.5 F1 = (beff/bw = 6.0) 0.8

Table 7.4N, & NA, Table NA.5: Note 5 Cl. 7.4.2(2) Cl. 7.4.2, Exp. (7.17) & NA: Table NA.5

F2 = 7.0/leff = 7.0/9.0 = (span > 7.0 m) 0.77 F3 = 310/sS ≤ 1.5 where ss = (fyk /gS) (As,req/As,prov) (SLS loads/ULS loads) (1/d) = 434.8 × (474/628) [(4.30 + 0.3 × 5.0)/13.38](61.1/55.9) = 434.8 × 0.75 × 0.43 × 1.09 = 153 MPa F3 = 310/ ss

NA, Table NA.5: Note 5

= 310/153 = 2.03 therefore, say = 1.50‡ = Permissible l/d = 26.8 × 1.5 × 0.8 × 0.77 × 1.50 = 37.1 = OK

Actual l/d = 9000/257 = 35

=Use 2 H20/rib (628 mm2/rib)

‡ Both A s,prov/As,req and any adjustment to N obtained from Exp. (7.16a) or Exp. (7.16b) is restricted to 1.5 by Note 5 to Table NA.5 in the UK NA.

61

3.3.7 Design for shear CL

CL

10 1


b = 150

a) Support A (and D) at solid/rib interface Shear at solid/rib interface = 29.3 kN/rib Taking solid area as the support, at d from face of support VEd = 29.3 − 0.232 × 0.90 × 13.38 = 26.5 kN/rib

Cl. 6.2.1(8) Cl. 6.2.2(1) & NA

Resistance VRd,c = (0.18/gC)k (100 rl fck)0.333 bwd where gC = 1.5 k = 1 + (200/d)0.5 ≤ 2 = 1 + (200/257)0.5 = 1.88 rl = Asl/bwd where Asl = assume only 1 H20 anchored = 314 mm2 bw = min. width between tension and compression chords. At bottom assuming 1/10 slope to rib: = 150 + 2 × (25 + 8 + 20/2)/10 = 159 mm d = 257 mm as before rl = 314/(159 × 257) = 0.0077 fck = 35 =VRd,c = (0.18/1.5) 1.88 (100 × 0.0077 × 35)0.333 × 159 × 257 = 0.68 × 159 × 257 = 27.8 kN/rib = No shear links required. But use nominal links to allow prefabrication. b) Support B (and C) at solid/rib interface Shear at solid/rib interface = 40.9 kN/rib [max(BA; BC)] At d from face of support VEd = 40.9 − 0.245 × 13.38 × 0.9 = 37.9 kN/rib

62

Cl. 6.2.1(5)

Cl. 6.2.1(8)

,',3

Resistance: VRd,c = (0.18/ gC)k (100 rl fck)0.333 bwd

Cl. 6.2.2(1) & NA

where gC = 1.5 k = 1 + (200/d)0.5 ≤ 2 = 1 + (200/245)0.5 = 1.90 rl = Asl/bwd where Asl = 2 H16 = 402 mm2 bw = 159 mm as before d = 245 mm as before rl = 0.0103 fck = 35 MPa = VRd,c = (0.18/1.5) 1.9 (100 × 0.0103 × 35)0.333 × 159 × 245 = 0.75 × 159 × 245 = 29.2 kN/rib = Shear links required. Shear links required for a distance: (37.9 − 29.2)/(13.38 × 0.9) + 245 = 722 + 245 = 967 mm from interface. Check shear capacity: VRd,max = acw bw zvfcd/(cot y + tan y) where acw = 1.0 bw = 159 mm as before z = 0.9d v = 0.6 (1 − fck/250) = 0.528 fcd = 35/1.5 = 23.3 MPa y = angle of inclination of strut. Rearranging formula above: (cot y + tan y) = acwbwzvfcd/VEd = (1.0 × 159 × 0.9 × 245 × 0.528 × 23.3) 41.6 × 103 = 10.4 By inspection, cot−1y << 21.8. But cot y restricted to 2.5 and = tan y = 0.4. VRd,max = 1.0 × 159 × 0.9 × 245 × 0.528 × 20/(2.5 + 0.4) = 127.6 kN = OK

Exp. (6.9) & NA

Cl. 6.2.3(2) & NA

63


Shear links: shear resistance with links VRd,s = (Asw/s) z fywd cot y ≤ VRd,max where Asw/s = area of legs of links/link spacing z = 0.9d as before fywd = 500/1.15 = 434.8 cot y = 2.5 as before = for VEd ≤ VRd,s Asw/s ≥ VEd/z fywd cot y ≥ 37.9 × 103/(0.9 × 245 × 434.8 × 2.5) ≥ 0.158 Maximum spacing of links = 0.75d = 183 mm = Use H8 @ 175 cc in 2 legs (Asw /s = 0.57) for min. 967 mm into rib

Exp. (6.8)

Cl. 9.2.2(6)

3.3.8 Indirect supports As the ribs of the slab are not supported at the top of the supporting beam sections (A, B, C, D), additional vertical reinforcement should be provided in these supporting beams and designed to resist the reactions. This additional reinforcement should consist of links within the supporting beams (see Beams design, Section 4.3.9). Support A (and D) at solid/rib interface: VEd = 26.5 kN/rib As,req = 26.3 × 1000/(500/1.15) = 60 mm2 This area is required in links within h/6 = 300/6 = 50 mm of the ribbed/solid interface and within h/2 = 300/2 = 150 mm of the centreline of the rib.

Cl. 9.2.5, Fig. 9.7

Fig. 9.7

Support B (and C) at solid/rib interface: VEd = 37.9 kN/rib As,req = 37.9 × 1000/(500/1.15) = 87 mm2 placed similarly

3.3.9 Other checks Check shear between web and flange By inspection, VEd ≤ 0.4 fct,d = OK

64

Cl. 6.4.2 (6) & NA

,',3
3.3.10 Summary of design 2H16 + 3H12/rib

2H16 + 3H12/rib H8 links in 2 legs @ 175cc A 550

2H20/rib

B

2H20/rib

1050 1000 1000 1050 7500

C

2H20/rib

1050 1000 1000 1050

9000

D 550

7500


fck = 35 MPa cnom = 25 mm

Figure 3.15 Summary of design Commentary It is usually presumed that the detailer would take the above design and detail the slab to normal best practice. As stated in Section 3.2.9, the detailer’s responsibilities, standards and timescales should be clearly defined but it would be usual for the detailer to draw and schedule not only the designed reinforcement but all the reinforcement required to provide a buildable solution. The work would usually include checking the following aspects and providing appropriate detailing: t Minimum areas t Curtailment lengths t Anchorages t Laps t U-bars t Rationalisation t Details and sections The determination of minimum reinforcement areas, curtailment lengths and laps using the principles in Eurocode 2 is shown in detail in the following calculations. In practice these would be determined from published tables of data or by using reference texts [12, 21]. Nonetheless the designer should check the drawing for design intent and compliance with standards. It is therefore necessary for the designer to understand and agree the principles of the details used.

3.3.11 Detailing checks a) Minimum areas i) Minimum area of reinforcement in flange As,min = 0.26 (fctm/fyk) btd ≥ 0.0013 btd

Cl. 9.3.1.1

65

where bt = width of tension zone fctm = 0.30 × fck0.666

Cl. 9.2.1.1, Exp. (9.1N) Table 3.1

As,min = 0.26 × 0.30 × 350.666 × 1000 × 100/500 = 166 mm2/m (r = 0.17%) = Use A142 in flange (say OK)

BS 8666[19]


ii) Secondary reinforcement Not applicable. iii) Maximum spacing of bars Maximum spacing of bars < 3 h < 400 mm By inspection.

OK

iv) Crack control Loading is the main cause of cracking = use Table 7.2N or Table 7.3N for wmax = 0.3 mm and max. ss = 200 MPa (see deflection check) Max. bar size = 25 mm or max. spacing = 250 mm OK by inspection v) Effects of partial fixity Assuming partial fixity exists at end supports, 15% of As is required to extend 0.2 × the length of the adjacent span. As,req = 15% × 525 = 79 mm2/rib For the rib in tension: As,min = 0.26 × 0.30 × 300.666 × 159 × 257/500 = 55 mm2/rib

Cl. 9.3.1.1.(3) Cl. 7.3.3(2) Cl. 7.3.1.5 Table 7.2N Table 7.3N

Cl. 9.3.1.2(2)

b) Curtailment Wherever possible simplified methods of curtailing reinforcement would be used. The following is intended to show how a rigorous assessment of curtailment of reinforcement might be undertaken.

66

i) End support A: bottom steel at support Check anchorage. As simply supported, 25% of As should be anchored in support. 25% × 595 = 148 mm2 Use 1 no. H20/rib (314 mm2/rib)

Cl. 9.3.1.1(4), 9.3.1.2(1) & Note, Cl. 9.2.1.4(1) & NA

ii) Check anchorage length Envelope of tensile force: To resist envelope of tensile force, provide reinforcement to al or lbd beyond centreline of support. For members without shear reinforcement, al = d = 232 By inspection, ssd = 0, lbd = lbd,min = max(10f, 100 mm)

Cl. 9.3.1.1(4), 9.2.1.3(1), Cl. 9.2.1.3(2), 9.2.1.3(3), Fig. 9.2 Cl. 9.2.1.3

iii) Indirect support As anchorage may be measured from face of indirect support, check force to be resisted at solid/rib interface: Fs = MEd/z + FE

Cl. 9.3.1.1(4), 9.2.1.4(2), 9.2.1.4(3), Fig. 9.3b

,',3

where MEd = 18.3 kNm/rib z = 220 as before FE = VEd × al/z where VEd = 29.3 kN/rib al = z cot y/2 = FE = VEd cot y/2 = 29.3 × 1.25 = 36.6 kN/rib Fs = 18.6 × 106/(220 × 103) + 36.6 = 121.1 kN iv) Anchorage length: lbd = alb,rqd ≥ lb,min where a = conservatively 1.0 lb,rqd = (f/4) (ssd/fbd) where f = 20 ssd = design stress in the bar at the ULS = 121.1 × 1000/314 = 385 MPa fbd = ultimate bond stress = 2.25 n1 n1 fct,d where n1 = 1.0 for good bond conditions n2 = 1.0 for bar diameter ≤ 32 mm fct,d = act fct,k/gC = 1.0 × 2.2/1.5 = 1.47 MPa fbd = 2.25 × 1.47 = 3.31 MPa = lb,rqd = (20/4) (385/3.31) = 581 mm lb,min = max[10f; 100 mm] = 200 mm = lbd = 581 mm measured from solid/rib intersection. i.e. 31 mm beyond centreline of support‡. v) End support A: top steel Assuming partial fixity exists at end supports, 15% of As is required to extend at least 0.2 × the length of the adjacent span§. As,req = 15% × 525 = 79 mm2/rib As,min = 0.26 × 0.30 × 350.666 × 159 × 257/500 = 68 mm2/rib Use 2 no. H12 T1/rib in rib and 2 no. H10 T1/rib between ribs (383 mm2/rib)

Exp. (9.3) Cl. 9.2.1.3, Exp. (9.2)

Cl. 8.4.4, Exp. (8.4) Exp. (8.3)

Cl. 8.4.2(2)

Cl. 3.1.6(2), Tables 3.1, 2.1 & NA Fig. 9.3

Cl. 9.3.1.2(2)

Cl. 9.3.1.1 Cl. 9.2.1.1(1), Exp. (9.1N)

‡ Whilst this would comply with the requirements of Eurocode 2, it is common practice

to take bottom bars 0.5 × a tension lap beyond the centreline of support (= 250 mm beyond the centreline of support; see model detail MS1 in SMDSC[9]). § It is usual to curtail 50% of the required reinforcement at 0.2l and to curtail the

remaining 50% at 0.3l or line of zero moment (see model detail MS2 in SMDSC[9]).

67


vi) Support B (and C): top steel At the centreline of support (2 no. H16 T + 3 no. H12 T)/rib are required. The intention is to curtail in two stages, firstly to 2 no. H16 T/rib then to 2 no. H12 T/rib. Curtailment of 2 no. H16 T/rib at support (capacity of 2 no. H12 T/rib + shift rule): Assume use of 2 no. H12 T throughout in midspan: Assuming z = 211 mm as before, MR2H12T = 2 × 113 × 434.8 × 211 = 20.7 kNm/rib (23.0 kNm/m) (Note: section remains under-reinforced) From analysis MEd = 23.0 kNm/m occurs at 2250 mm (towards A) and 2575 mm (towards B). Shift rule: al = z cot y/2 Assuming z = 211 mm as before al = 1.25 × 211 = 264 mm = 2 no. H12 T are adequate from 2250 + 264 = 2513 mm from B towards A and 2575 + 263 = 2838 mm from B towards C. = Curtail 2 no. H16 T @ say 2600 from BA and 2850 from BC Curtailment of 3 no. H12 T/rib at support (capacity of 2 no. H16 T/rib + shift rule): MR2H16T = 2 × 201 × 434.8 × 211 = 36.9 kNm/rib (41.0 kNm/m) (Note: section remains under-reinforced) From analysis MEd = 41.0 kNm/m occurs at 1310 mm (towards A) and 1180 mm (towards C). Shift rule: al = 263 mm as before = 2 no. H16 T are adequate from 1310 + 263 = 1573 mm from B towards A and 1180 + 263 = 1443 mm from B towards C. = Curtail 3 no. H12 at say 1600 from B (or C). (See Figure 3.16)

68

vii) Support B (and C): bottom steel at support At the support 25% of span steel required 0.25 × 628 = 157 mm2 Try 1 no. H16 B/rib (201)

Cl. 9.3.1.1(4), 9.2.1.5(1), 9.2.1.4(1)

This reinforcement may be anchored into indirect support or carried through.

Fig. 9.4

,',3
a1 = 264

2H16 + 3H12 per rib

MEd = 77.1 x 0.9 = 60.4 kNm/rib ‘Shift’ moment MR = As(fyk/gS)z

lbd

2H16/rib

MEd MEd = 36.79 kNm/rib

2H12/rib


MEd = 20.7 kNm/rib A

C

B 264 1310

1180 264

2250

2575

264

264 a) Design moments and moment resistance 2H12

3H12

2H12

2H16 1600 2600

1600 2850

b) Curtailment of reinforcement

p

p

viii) Support B (and C): bottom steel curtailment BA and BC To suit prefabrication 2 no. H20/rib will be curtailed at solid/rib interface, 1000 mm from BA (B towards A) and BC. From analysis, at solid/rib interface sagging moment = 0. From analysis, at a1 from solid/rib interface, i.e. at 1000 + 1.25 × 244 = 1303 mm at 1305 mm from BA sagging moment = say 5 kNm/rib at 1305 mm from BC sagging moment = 0 Use 1 no. H16 B/rib (201) c) Laps At AB, check lap 1 no. H20 B to 2 no. H20 B in rib full tension lap: l0 = a1 a6 lb,rqd > l0,min where a1 = 1.0 (cd = 45 mm, i.e. < 3f) a6 = 1.5 (as > 50% being lapped) lb,rqd = (f/4) (ssd/fbd)

Exp. (8.10) Table 8.2

where f = 20 ssd = 434.8 fbd = 3.0 MPa as before 69


l0,min = max. 10f or 100 = 200 l0 = 1.0 × 1.5 × (20/4) × 434.8/3.0 = 1087 mm, say = 1200 mm At BA and BC, check lap 2 no. H12 T to 2 no. H16 T in rib – full tension lap: l0 = a1 a6 lb,rqd > l0,min where a1 = 0.7 (cd = 45 mm, i.e. > 3f) a6 = 1.5 (as > 50% being lapped) lb,rqd = (f/4) (ssd/fbd)

Exp. (8.10)

where f = 20 ssd = 434.8 fbd = 2.1 (3.0 MPa as before but n1 = 0.7 for “not good bond conditions”) l0,min = max. 10f or 100 = 120

Cl. 8.4.2

l0 = 0.7 × 1.5 × (12/4) × 434.8/2.1 = 651 mm, say = 700 mm But to aid prefabrication take to solid/rib intersection 1000 mm from centre of support. At BA and BC, check lap 1 no. H16 B to 2 no. H20 B in rib: By inspection, nominal say, 500 mm

Exp. (8.6) SMDSC[9]

Table 8.2

SMDSC[9]

SMDSC[9]

d) RC detail of ribbed slab Links not shown for clarity. Cover 25 mm to links.

600 600 1000 1000 1000 1250

200 200 1500 2H12T in rib and 2H1OT between

2H12T

2H20B/rib

150 550 1200

2H16 + 3H12/rib A143 fabric 2H12T/rib

2H16 + 3H12/rib

2H12 2H12 + 2H1O 2H16 3H12 2H12

1H20B

600 1250 1000

2H16 3H12 2H12

2H12 3H12 2H16

1H16B/rib

2H20B/rib

500 1000 1000 500 7500

1H16B/rib 500 1000 1000

9000

Figure 3.17 Curtailment of flexural reinforcement in ribbed slab

70

,',3

Mabl^qZfie^bl_hkma^]^lb`gh_Zk^bg_hk\^]\hg\k^m^_eZmleZ[pbmahnm\henfga^Z]l'Ma^leZ[ bliZkmh_ZeZk`^k_ehhkieZm^Zg]blmZd^g_khf@nb]^mhma^]^lb`gZg]\hglmkn\mbhgh_k^bg_hk\^] \hg\k^m^_eZmleZ[lT+0V%pa^k^_bgbm^ê^f^gmZgZerlblZg]]^lb`gmh>nkh\h]^+blbeenlmkZm^]':l pbmama^@nb]^%`kb]ebg^<pbee[^]^lb`g^][nm%_hkma^lZd^h_beenlmkZmbhg%\h^__b\b^gmlpbee[^ nl^]mh^lmZ[ebla]^lb`gfhf^gmlZg]la^Zklbgmabl\kbmb\ZeZk^Zh_ma^leZ[' Ikhc^\m]^mZbel

chg

Ch[gh'

Flat slab

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

The slab is for an office where the specified load is 1.0 kN/m2 for finishes and 4.0 kN/m2 imposed (no partitions). Perimeter load is assumed to be 10 kN/m. Concrete is C30/37. The slab is 300 mm thick and columns are 400 mm square. The floor slabs are at 4.50 m vertical centres. A 2 hour fire rating is required. A

4.0

B

4.0

Bb

4.0

C

6.0

D E

1 200 x 200 hole 8.0

2

8.0

3

9.6 300 mm flat slabs All columns 400 mm sq.

8.6

200 x 200 hole

Figure 3.18 Part p plan of flat slab

3.4.1 Actions

kN/m2

Permanent: Self-weight 0.30 × 25 Finishes Total Variable: Offices

‡

= 7.5 = 1.0 gk = 8.5

EC1-1-1: Table A1

jk = 4.0‡

Client requirement. See also BS EN 1991–1–1, Tables 6.1, 6.2, Cl. 6.3.2.1(8) & NA. 71

3.4.2 Cover cnom: cnom = cmin + Dcdev

Exp. (4.1)

where cmin = max[cmin,b ; cmin,dur; 10 mm]

Cl. 4.4.1.2(3)

where cmin,b = 20 mm, assuming 20 mm diameter reinforcement cmin,dur = 15 mm for XC1 and using C30/37


Dcdev = 10 mm Fire: For 2 hours resistance, amin = 35 mm = not critical = cnom = 20 + 10 = 30 mm

Table 4.1. BS 8500-1: Table A4. EC2-1-2: Table 5.9

3.4.3 Load combination and arrangement qk = 4.0 kN/m2 gk = 8.5 kN/m2 1

9600

2

8600

3

Figure 3.19 Panel centred on grid C Ultimate load, n: By inspection, Exp. (6.10b) is critical. n = 1.25 × 8.50 + 1.5 × 4.0 = 16.6 kN/m2 Arrangement: Choose to use all-and-alternate-spans-loaded load cases and coefficients‡.

Fig. 2.5 EC0: Exp. (6.10b)

Cl. 5.1.3(1) & NA: Table NA.1 (option b)

3.4.4 Analysis grid line C Consider grid line C as a bay 6.0 m wide. (This may be conservative for grid line C but is correct for grid line D etc.) MEd Effective spans: 9600 – 2 × 400/2 + 2 × 300/2 = 9500 mm 8600 – 2 × 400/2 + 2 × 300/2 = 8500 mm Check applicability of moment coefficients: 8500/9500 = 0.89 = as spans differ by less than 15% of larger span, coefficients are applicable.

Tables C2 & C3

‡The

Cl. 5.3.1 & NA

all-spans-loaded case with 20% redistribution of support moments would also have been acceptable but would have involved some analysis. The use of Table 5.9 in BS EN 1992–1–2 (Fire resistance of solid flat slabs) is restricted to where redistribution does not exceed 15%; the coefficients presume 15% redistribution at supports. 72

Cl. 5.3.2.2(1)

Table C3

,'-3?eZmleZ[

As two span, use table applicable to beams and slabs noting increased coefficients for central support moment and shear.

Table C3

Design moments in bay. Spans: MEd = (1.25 × 8.5 × 0.090 + 1.5 × 4.0 × 0.100)× 6.0 × 9.52 = 842.7 kNm Support: MEd = 16.6 × 0.106 × 6.0 × 9.52 = 952.8 kNm D

C


6000 1

1500 Column strip

Middle strip

1500

Column 1500 strip

2

1500 1500 3000 1500 1500 Column strip Middle strip Column strip

Figure 3.20 Column and middle strips p Apportionment of moments between column strips and middle strips: Apportionment (as %) Column strip –ve (hogging) Long span = 70%§ Short span = 75% +ve (sagging) 50%

Middle strip Long span = 30% Short span = 25% 50%

Parallel to grid C, column strip is ly/2 = 3 m wide. The middle strip is also 3 m wide.

Table I.1; CS Flat slab guide[27] Table I.1 NA.3[1a]; Fig. I.1

Long span moments: MEd Column strip, 3 m wide Middle strip, 3 m wide –ve (hogging) 0.70 × 952.8/3.0 = 222.3 kNm/m 0.30 × 952.8/3.0 = 95.3 kNm/m +ve (sagging) 0.50 × 842.7/3.0 = 140.5 kNm/m 0. 50 × 842.7/3.0 = 140.5 kNm/m §

The Concrete Society’s TR 64[27] recommends a percentage, k1, based on ly /lz Assuming ly /lz = 1.5 the distribution of moments in the long span between column strips and middle strips is given as 70% and 30%. 73

Punching shear force, VEd: At C2, VEd = 16.6 × 6.0 × 9.6‡ × 0.63 × 2 = 1204.8 kN At C1 (and C3) VEd = 16.6 × 6.0 × 9.6 × 0.45 + (10 + 0.2 × 0.3 × 25)§ × 1.25 × 6.0 = 516.5 kN

Table C3 Table C3

3.4.5 Design grid line C


Effective depth, d: d = 300 − 30 − 20/2 = 260 mm a) Flexure: column strip and middle strip, sagging MEd = 140.5 kNm/m K = MEd/bd2fck = 140.5 × 106/(1000 × 2602 × 30) = 0.069 z d = 0.94 z/ z = 0.94 × 260 = 244 mm As = MEd/ffyd z = 140.5 × 106/(244 × 500/1.15) = 1324 mm2/m (r r = 0.51%) Try H20 @ 200 B1 (1570 mm2/m) b) Deflection: column strip and middle strip Check span-to-effective-depth ratio. Allowable l/ l d = N × K × F1 × F2 × F3 where N = 20.3 (r = 0.51%, fck = 30) K = 1.2 (flat slab) F1 = 1.0 (beff/bbw = 1.0) F2 = 1.0 (no brittle partitions)# F3 = 310/s ss ≤ 1.5 where* ss = ssu (As,reqq/As,prov) 1/d where ssu = (500/1.15) × (8.5 + 0.3 × 4.0)/16.6 = 254 MPa (or ≈ 253 MPa; from Figure C3 Gk/Qk = 2.1, c2 = 0.3 and gG = 1.25) d = redistribution ratio = 1.03 = ss ≈ 253 × (1324/1570)/1.03 = 207 = F3 = 310/207 = 1.50† = Allowable l/ l d = 20.3 × 1.2 × 1.50 = 36.5

Table C5

Appendix B Cl. 7.4.2(2) Appendix C Tables C10–C13

Cl. 7.4.2, Exp. (7.17) Table 7.4N, & NA, Table NA.5 Note 5

Fig. C3 Fig. C14

‡ As punching shear force (rather than a beam shear force) ‘effective’ span is not

appropriate. § Cladding

and strip of slab beyond centre of support.

# Otherwise

for flat slabs 8.5/9.5 = 0.89 as span > 8.5 m.

* See Appendix B1.5 † In line with Note 5 to Table NA.5, 1.50 is considered to be a maximum for 310/s ss. 74

Cl. 7.4.2(2)

,'-3?eZmleZ[

Actual l/d = 9500/260 = 36.5

= OK‡ Use H20 @ 200 B1 (1570)§


c) Flexure: column strip, hogging MEd = 222.3 kNm/m K = MEd/bd2fck = 222.3 × 106/(1000 × 2602 × 30) = 0.109 z/d = 0.89 z = 0.89 × 260 = 231 mm As = MEd/fydz = 222.3 × 106/(231 × 500/1.15) = 2213 mm2/m (r = 0.85%) Try H20 @ 125 T1 (2512 mm2/m)# d) Flexure: middle strip, hogging MEd = 95.3 kNm/m K = MEd/bd2fck = 95.3 × 106/(1000 × 2602 × 30) = 0.069 z/d = 0.95 z = 0.95 × 260 = 247 mm As = MEd/fydz = 95.3 × 106/(247 × 500/1.15) = 887 mm2/m (r = 0.34%) Try H16 @ 200 T1 (1005 mm2/m) e) Requirements i) In column strip, inside middle 1500 mm There is a requirement to place 50% of At within a width equal to 0.125 of the panel width on either side of the column. Area required = (3 × 2213 + 3 × 887)/2 mm2 = 4650 mm2 Over width = 2 × 0.125 × 6.0 m = 1500 mm i.e. require 4650/1.5 = 3100 mm2/m for 750 mm either side of the column centreline. Use H20 @ 100 T1 (3140 mm2/m) 750 mm either side of centre of support (16 no. bars) (r = 0.60%)

Table C5

Table C5

Cl. 9.4.1(2)

ii) In column strip, outside middle 1500 mm Area required = 3.0 × 2213 – 16 × 314 mm2 = 1615 mm2 Over width = 3000 – 2 × 750 mm = 1500 mm i.e. 1077 mm2/m Use H20 @ 250 T1 (1256 mm2/m) in remainder of column strip ‡ Note: Continuity into columns will reduce sagging moments and criticality of deflection check (see Figures 3.26 and 3.27). § Note requirement for at least 2 bars in bottom layer to carry through column. # The hogging moment could have been considered at face of support to reduce the amount of reinforcement required.

Cl. 9.4.1(3) 75


iii) In middle strip

Use H16 @ 200 T1 (1005 mm2/m)

iv) Perpendicular to edge of slab at edge column Design transfer moment to column Mt = 0.17 bed 2fck where be = cz + y = 400 + 400 = 800 mm Mt = 0.17 × 800 × 2602 × 30 × 10−6 = 275.8 kNm K = MEd/bd2fck = 275.8 × 106/(800 × 2602 × 30) = 0.170 z/d = 0.82 z = 0.82 × 260 = 213 mm As = MEd/fydz = 275.8 × 106/(213 × 500/1.15) = 2978 mm2/m This reinforcement to be placed within cx + 2cy = 1100 mm

Cl. 9.4.2(1), I.1.2(5) Fig. 9.9

SMDSC[9]

Try 10 no. H20 T1 U-bars in pairs @ 200 (3140 mm2) local to column (max. 200 mm from column) Note: Where a 200 × 200 hole occurs on face of column, be becomes 600 mm and pro rata, As,req becomes 2233 mm2 i.e. use 4 no. H20 each side of hole (2512 mm2). v) Perpendicular to edge of slab generally Assuming that there is partial fixity along the edge of the slab, top reinforcement capable of resisting 25% of the moment in the adjacent span should be provided OK 0.25 × 2213 = 553 mm2/m vi) Check minimum area of reinforcement As,min = 0.26 (fctm/fyk) btd ≥ 0.0013 btd where bt = width of tension zone fctm = 0.30 × fck0.666 As,min = 0.26 × 0.30 × 300.666 × 1000 × 260/500 = 390 mm2/m (r = 0.15%) Use H12 @ 200 (565 mm2/m) The reinforcement should extend 0.2h from edge = 600 mm

Cl. 9.3.1.2(2), 9.2.1.4(1) & NA

Cl. 9.3.1.1, 9.2.1.1 Table 3.1

Cl. 9.3.1.4(2)

3.4.6 Analysis grid line 1 (grid 3 similar) Consider grid line 1 as being 9.6/2 + 0.4/2 = 5.0 m wide with continuous spans of 6.0 m. Column strip is 6.0/4 + 0.4/2 = 1.7 m wide. Consider perimeter load is carried by column strip only.

76

Cl. 5.1.1(4)

,'-3?eZmleZ[

qk slab = 20.0 kN/m gk cladding = 10.0 kN/m = 42.5 kN/m gk slab C

D

6000

6000

E

6000

F


p Actions: Permanent from slab Variable from slab Permanent perimeter load

gk = 5 × 8.5 kN/m2 = 42.5 kN/m qk = 5 × 4.0 kN/m2 = 20.0 kN/m gk = 10.0 kN/m

Load combination and arrangement: As before, choose to use all-spans-loaded case and coefficients Ultimate load, n: By inspection, Exp. (6.10b) is critical. n = 1.25 × (42.5 +10) + 1.5 × 20 = 95.6 kN/m Perimeter load, 10 × 1.25 = 12.5 kN/m Effective span, leff Effective span = 6000 – 2 × 400/2 + 2 × 300/2 = 5900 Design moments in bay, MEd: In spans (worst case, end span assuming pinned support) MEd = 0.086 × 83.0 × 5.92 = 248.5 kNm At supports (worst case 1st support) MEd = 0.086 × 83.0 × 5.92 = 248.5 kNm Additional moment in column strip only due to perimeter load, spans (and supports, worst case) MEd = 0.086 × 12.5 × 5.92 = 37.4 kNm Apportionment to column strips and middle strips: Apportionment (as %) Column strip, 1.7 m wide Middle strip Short span = 25% –ve (hogging) Short span = 75% 50% +ve (sagging) 50%

Cl. 5.1.3(1) & NA: Table NA.1 (option c) Fig. 2.5 EC0: Exp. (6.10b)

Cl. 5.3.2.2(1)

Table C2 Table C2

NA.3[1a]: Fig. I.1 Table I.1 CS Flat slab guide[27]

Short span moments: MEd Column strip, 1.7 m wide Middle strip, 3.3 m wide –ve (hogging) (0.75 × 248.5 + 37.4)/1.70 0.25 × 248.5/3.3 = 131.6 kNm/m = 18.8 kNm/m +ve (sagging) (0.50 × 248.5 + 37.4)/1.70 0.50 × 248.5/3.3 = 95.1 kNm/m = 37.6 kNm/m 77

Punching shear force, VEd For internal supports, as before = 516.5 kN For penultimate support, 516.5 × 1.18 = 609.5 kN

Table C3


3.4.7 Design grid line 1 (grid 3 similar) Cover: cnom = 30 mm as before d = 300 − 30 − 20 − 20/2 = 240 mm a) Flexure: column strip, sagging MEd = 95.1 kNm/m K = MEd/bd2fck = 95.1 × 106/(1000 × 2402 × 30) = 0.055 z/d = 0.95 z = 0.95 × 240 = 228 mm As = MEd/fyd z = 95.1 × 106/(228 × 500/1.15) = 959 mm2/m (r = 0.40%) Try H16 @ 200 B2 (1005 mm2/m) b) Deflection: column strip Check span-to-effective-depth ratio. Allowable l/d = N × K × F1 × F2 × F3 where N = 26.2 (r = 0.40%, fck = 30) K = 1.2 (flat slab) F1 = 1.0 (beff/bw = 1.0) F2 = 1.0 (no brittle partitions) F3 = 310/ ss ≤ 1.5 where ss = ssu (As,req/As,prov) 1/d where ssu ≈ 283 MPa (from Figure C3 and Gk/Qk = 3.6, c2 = 0.3, gG = 1.25) d = redistribution ratio = 1.08 = ss ≈ 283 × (959/1005)/1.08 = 250 = F3 = 310/250 = 1.24 =Allowable l/d = 26.2 × 1.2 × 1.24 = 39.0 Actual l/d = 5900/240 = 24.5 = OK Use H16 @ 200 B2 (1005 mm2/m) c) Flexure: middle strip, sagging MEd = 37.6 kNm/m By inspection, z = 228 mm As = MEd/fydz = 37.6 × 106/(228 × 500/1.15) = 379 mm2/m (r = 0.56%)

78

Table C5

Appendix B Appendix C7 Tables C10–C13 Cl. 7.4.2, Exp. (7.17), Table 7.4N & NA, Table NA.5: Note 5

Fig. C3 Table C14 Fig. C3

,'-3?eZmleZ[

By inspection, deflection OK.


Check minimum area of reinforcement. As,min = 0.26 (fctm/fyk) btd ≥ 0.0013 btd where bt = width of tension zone fctm = 0.30 × fck0.666 As,min = 0.26 × 0.30 × 300.666 × 1000 × 240/500 = 361 mm2/m (r = 0.15%) Use H12 @ 300 T2 (376 mm2/m) d) Flexure: column strip, hogging MEd = 131.6 kNm/m K = MEd/bd2fck = 131.6 × 106/(1000 × 2402 × 30) = 0.076 z/d= 0.928 z = 0.928 × 240 = 223 mm As = MEd/fydz = 131.6 × 106/(223 × 500/1.15) = 1357 mm2/m (r = 0.56%) Try H20 @ 200 T2 (1570 mm2/m)‡ e) Flexure: middle strip, hogging MEd = 18.8 kNm/m By inspection, z = 228 mm As = MEd/fydz = 18.8 × 106/(228 × 500/1.15) = 190 mm2/m (r = 0.08%) As,min as before = 361 mm2/m (r = 0.15%) Try H12 @ 300 T2 (376 mm2/m) f) Requirements There is a requirement to place 50% of At within a width equal to 0.125 of the panel width on either side of the column. As this column strip is adjacent to the edge of the slab, consider one side only: Area required = (1.5 × 1357 + 3.3 × 190)/2 mm2 = 1334 mm2 Within = 0.125 × 6.0 m = 750 mm of the column centreline, i.e. require 1334/0.75 = 1779 mm2/m for 750 mm from the column centreline.

Cl. 9.3.1.1, 9.2.1.1

Table 3.1

Table C5

Table C5

Cl. 9.3.1.1, 9.2.1.1

Cl. 9.4.1(2)

‡ The

hogging moment could have been considered at face of support to reduce the amount of reinforcement required. This should be balanced against the effect of the presence of a 200 × 200 hole at some supports which would have the effect of increasing K but not unduly increasing the total amount of reinforcement required in the column strip (a 1.5% increase in total area would been required). 79

Allowing for similar from centreline of column to edge of slab: Use 6 no. H20 @ 175 T2(1794 mm2/m) (r = 0.68%) between edge and to 750 mm from centre of support In column strip, outside middle 1500 mm, requirement is for 1.7 × 1357 – 6 × 314 = 422 mm2 in 750 mm, i.e. 563 mm2/m Use H12 @ 175 T2 (646 mm2/m) in remainder of column strip Use H12 @ 300 T2 (376 mm2/m)


In middle strip

3.4.8 Analysis grid line 2 Consider panel on grid line 2 as being 9.6/2 + 8.6/2 = 9.1 m wide and continuous spans of 6.0 m. Column strip is 6.0/2 = 3.0 m wide. (See Figure 3.20). qk slab = 36.4 kN/m gk slab = 77.4 kN/m C

6000

D

6000

E

6000

F

Figure 3.22 Internal p panel on grid 2 Slab gk = 9.1 × 8.5 kN/m2 = 77.4 kN/m Slab qk = 9.1 × 4.0 kN/m2 = 36.4 kN/m Actions, load combination and arrangement: Choose to use all-spans-loaded case. Ultimate load, n: By inspection, Exp. (6.10b) is critical. n = 1.25 × 77.4 + 1.5 × 36.4 = 151.4 kN/m

Fig. 2.5 EC0: Exp. (6.10b)

Effective span, leff: Effective span = 5900 mm as before.

Cl. 5.3.2.2(1)

Design moments in bay, MEd: Spans (worst case, end span assuming pinned support) MEd = 0.086 × 151.4 × 5.92 = 453.2 kNm

Table C2

Support (worst case 1st support) MEd = 0.086 × 151.4 × 5.92 = 453.2 kNm Additional moment in column strip only due to perimeter load.

80

Cl. 5.1.3(1) & NA: Table NA.1 (option c)

Table C2

,'-3?eZmleZ[

Apportionment to column strips and middle strips: MEd Column strip, 3.0 m wide Middle strip, 6.1 m wide 0.25 × 453.2/6.1 –ve (hogging) 0.75 × 453.2/3.0 = 113.3 kNm/m = 18.5 kNm/m +ve (sagging) 0.50 × 453.2/3.0 = 75.5 kNm/m

0.50 × 453.2/6.1 = 37.1 kNm/m


Punching shear force, VEd, as before.

3.4.9 Design grid line 2 Effective depth, d d = 300 − 30 − 20 − 20/2 = 240 mm a) Flexure: column strip, sagging MEd = 75.5 kNm/m By inspection, z = 228 mm As = MEd/fydz = 75.5 × 106/(228 × 500/1.15) = 761 mm2/m (r = 0.32%) Try H16 @ 250 B2 (804 mm2/m) Deflection: column strip By inspection, OK.

Table C5

b) Flexure: column strip, sagging MEd = 37.1 kNm/m By inspection, z = 228 mm As = MEd/fydz = 37.1 × 106/(228 × 500/1.15) = 374 mm2/m (r = 0.55%) By inspection, deflection OK. Try H10 @ 200 B2 (393 mm2/m) c) Flexure: column strip, hogging MEd = 113.3 kNm/m K = MEd/bd2fck = 113.3 × 106/(1000 × 2402 × 30) = 0.065 z/d = 0.94 z = 0.928 × 240 = 225 mm

Table C5

As = MEd/fydz = 113.3 × 106/(225 × 500/1.15) = 1158 mm2/m (r = 0.48%) Try H20 @ 250 T2 (1256 mm2/m)‡ d) Flexure: middle strip, hogging MEd = 18.5 kNm/m By inspection, z = 228 mm ‡ The hogging moment could have been considered at face of support to reduce the amount of reinforcement required.

81


As = MEd/fydz = 18.5 × 106/(228 × 500/1.15) = 187 mm2/m (r = 0.08%) As before minimum area of reinforcement governs As,min = 0.26 × 0.30 × 300.666 × 1000 × 240/500 = 361 mm2/m (r = 0.15%) Try H12 @ 300 B2 (376 mm2/m)

Table C5 Cl. 9.3.1.1, 9.2.1.1

e) Requirements Regarding the requirement to place 50% of At within a width equal to 0.125 of the panel width on either side of the column: Area required = (3.0 × 1158 + 6.1 × 187)/2 mm2 = 2307 mm2 Within = 2 × 0.125 × 6.0 m = 1500 mm centred on the column centreline, i.e. require 2307/1.5 = 1538 mm2/m for 750 mm either side of the column centreline. Use H20 @ 200T2 (1570 mm2/m) 750 mm either side of centre of support (r = 0.60%) In column strip, outside middle 1500 mm, requirement is for 3.0 × 1158 – 1.5 × 1570 = 1119 mm2 in 1500 mm, i.e. 764 mm2/m Use H16 @ 250 T2 (804 mm2/m) in remainder of column strip In middle strip:

Use H12 @ 300 T2 (376 mm2/m)

3.4.10 Punching shear, central column, C2 At C2, applied shear force, VEd = 1204.8 kN‡ a) Check at perimeter of column vEd = bVEd /uid < vRd,max where b = factor dealing with eccentricity; recommended value 1.15 VEd = applied shear force ui = control perimeter under consideration. For punching shear adjacent to interior columns u0 = 2(cx + cy) = 1600 mm d = mean effective depth = (260 + 240)/2 = 250 mm = 1.15 × 1204.8 × 103/1600 × 250 = 3.46 MPa vEd vRd,max = 0.5vfcd

‡ Column C2 is taken to be an internal column. In the case of a penultimate column, an additional elastic reaction factor should have been considered.

82

Cl. 6.4.3(2), 6.4.5(3) Fig. 6.21N & NA Cl. 6.4.5(3) Exp. (6.32) Cl. 6.4.5(3) Note

,'-3?eZmleZ[

where v = 0.6(1 − fck/250) = 0.528 fcd = acclfck /gC = 1.0 × 1.0 × 30/1.5 = 20 = 0.5 × 0.528 × 20 = 5.28 MPa

= OK


b) Check shear stress at control perimeter u1 (2d from face of column) vEd = bVEd/u1d < vRd,c

Table C7 § Cl. 6.4.2

where b, VEd and d as before u1 = control perimeter under consideration. For punching shear at 2d from interior columns u1 = 2(cx + cy) + 2Q × 2d = 4741 mm vEd = 1.15 × 1204.8 × 103/4741 × 250 = 1.17 MPa vRd,c = 0.18/ gC k (100 rlfck)0.333

Exp. (6.47) & NA

where gC = 1.5 k = 1 + (200/d)0.5 ≤ 2 k = 1 + (200/250)0.5 = 1.89 rl = (rly rlz)0.5 = (0.0085 × 0.0048)0.5 = 0.0064

Cl. 6.4.4.1(1)

where rer, rlz = Reinforcement ratio of bonded steel in the y and z direction in a width of the column plus 3d each side of column# fck = 30 vRd,c = 0.18/1.5 × 1.89 × (100 × 0.0064 × 30)0.333 = 0.61 MPa = Punching shear reinforcement required

Table C5*

c) Perimeter at which punching shear links are no longer required uout = VEd × b/(d vRd,c) uout = 1204.8 × 1.15 × 103/(250 × 0.61) = 9085 mm Length of column faces = 4 × 400 = 1600 mm Radius to uout = (9085 – 1600)/2Q = 1191 mm from face of column Perimeters of shear reinforcement may stop 1191 – 1.5 × 250 = 816 m from face of column Shear reinforcement (assuming rectangular arrangement of links): sr,max = 250 × 0.75 = 187, say = 175 mm

Fig. 6.13

Exp. (6.54)

Cl. 6.4.5(4) & NA Cl. 9.4.3(1)

§ At the perimeter of the column, v Rd,max assumes the strut angle is 45°, i.e. that cot y = 1.0. Where cot y = < 1.0, vRd,max is available from Table C7. #The

values used here for r ly , r lz ignore the fact that the reinforcement is concentrated over the support. Considering the concentration would have given a higher value of VRd,c at the expense of further calculation to determine r ly , r lz at 3d from the side of the column. * vRd,c for various values of d and rl is available from Table C6. 83


Inside 2d control perimeter, st,max = 250 × 1.5 = 375, say 350 mm Outside control perimeter st,max = 250 × 2.0 = 500 mm Assuming vertical reinforcement: At the basic control perimeter, u1, 2d from the column‡: Asw ≥ (vEd – 0.75vRd,c) sr u1/1.5fywd,ef) where fywd,ef = effective design strength of reinforcement = (250 + 0.25d) < fyd = 312 MPa For perimeter u1 Asw = (1.17 – 0.75 × 0.61) × 175 × 4741/(1.5 × 312) = 1263 mm2 per perimeter Asw,min ≥ 0.08fck0.5(sr st)/(1.5 fyk sin a + cos a) where Asw,min = minimum area of a single leg of link a = angle between main reinforcement and shear reinforcement; for vertical reinforcement sin a = 1.0

Cl. 9.4.3(2)

Exp. (6.52)

Cl. 6.4.5(1)

Exp. (9.11)

Asw,min ≥ 0.08 × 300.5 (175 × 350)/(1.5 × 500) = 36 mm2 = Try H8 legs of links (50 mm2) Asw /u1 ≥ 1263/4741 = 0.266 mm2/mm Using H8 max. spacing = min[50/0.266; 1.5d] = min[188; 375] = 188 mm cc = Use min. H8 legs of links at 175 mm cc around perimeter u1 Perimeters at 0.75d = 0.75 × 250 = 187.5 mm say = 175 mm centres d) Check area of reinforcement > 1263 mm2 in perimeters inside u1§ 1st perimeter to be > 0.3d but < 0.5d from face of column. Say 0.4d = 100 mm from face of column.

Cl. 9.4.3

Cl. 9.4.3(1)

Fig. 9.10, Cl. 9.4.3(4)

By inspection of Figure 3.23 the equivalent of 10 locations are available at 0.4d from column therefore try 2 × 10 no. H10 = 1570 mm2. By inspection of Figure 3.23 the equivalent of 18 locations are available at 1.15d from column therefore try 18 no. H10 = 1413 mm2. By inspection of Figure 3.23 the equivalent of 20 locations are available at 1.90d from column therefore try 20 no. H10 = 1570 mm2. By inspection of Figure 3.23 beyond u1 to uout grid of H10 at 175 x 175 OK. ‡ Clause 6.4.5 provides Exp. (6.52), which by substituting v for v Ed Rd,c, allows calculation of the area of required shear reinforcement, Asw, for the basic control perimeter, u1. § The same area of shear reinforcement is required for all perimeters inside or outside perimeter u1. See Commentary on design, Section 3.4.14. Punching shear reinforcement is also subject to requirements for minimum reinforcement and spacing of shear reinforcement (see Cl. 9.4.3).

84

Cl. 6.4.5 Exp. 6.5.2

Cl. 9.4.3

,'-3?eZmleZ[

e) Summary of punching shear refreshment required at column C2 uout

C

S = 112 H10 legs of links u1 at 2d from column

175 175 175 175 200 200 200 175 175 175 175

100 400 100 716

2


716

Punching shear reinforcement no longer required 1.5d = 375

uout

175 175 175 175 200 200 200 175 175 175 175 375

716

100

400

100

716

Figure 3.23 Punching shear links at column C2 (112 no. links) (column D2 similar)

3.4.11 Punching shear, edge column Assuming penultimate support, VEd = 1.18 × 516.5 = 609.5 kN a) Check at perimeter of column vEd = b VEd/uid < vRd,max where b = factor dealing with eccentricity; recommended value 1.4 VEd = applied shear force ui = control perimeter under consideration. For punching shear adjacent to edge columns u0 = c2 + 3d < c2 + 2c1 = 400 + 750 < 3 × 400 mm = 1150 mm d = as before 250 mm vEd = 1.4 × 609.5 × 103/1150 × 250 = 2.97 MPa vRd,max, as before = 5.28 MPa = OK

Table C3 Cl. 6.4.3(2), 6.4.5(3) Fig. 6.21N & NA Cl. 6.4.5(3)

Exp. (6.32) Cl. 6.4.5(3) Note 85

Cl. 6.4.2

Fig. 6.15

Exp. (6.47) & NA

where gC = 1.5 k = as before = 1 +(200/250)0.5 = 1.89 rl = (r lyr lz )0.5 where rer, rlz = Reinforcement ratio of bonded steel in the y and z direction in a width of the column plus 3d each side of column. r ly: (perpendicular to edge) 10 no. H20 T2 + 6 no. H12 T2 in 2 × 750 + 400, i.e. 3818 mm2 in 1900 mm =r ly = 3818/(250 × 1900) = 0.0080 r lz : (parallel to edge) 6 no. H20 T1 + 1 no. T12 T1 in 400 + 750 i.e. 1997 mm2 in 1150 mm. =r lz = 1997/(250 × 1150) = 0.0069 r l = (0.0080 × 0.0069)0.5 = 0.0074 fck = 30 vRd,c = 0.18/1.5 × 1.89 × (100 × 0.0074 × 30)0.333 = 0.64 MPa = Punching shear reinforcement required C

3d = 750

6H20T1 @175

3d = 750 10H20 U-bars in pairs @ 200 cc 400

H12 @ 200 U-bars

400

1

3d = 750


b) Check shear stress at basic perimeter u1 (2.0d from face of column) vEd = bVEd/u1d < vRd,c where b, VEd and d as before u1 = control perimeter under consideration. For punching shear at 2d from edge column columns u1 = c2 + 2c1+ Q × 2d = 2771 mm vEd = 1.4 × 609.5 × 103/2771 × 250 = 1.23 MPa vRd,c = 0.18/ gC × k × (100 rlfck)0.333

H12 @ 175T1

Figure 3.24 Flexural tensile reinforcement adjacent to columns C1 (and C3) ‡

86

vRd,c for various values of d and rl is available from Table C6.

Cl. 6.4.4.1(1)

Table C6‡

,'-3?eZmleZ[


c) Perimeter at which punching shear links no longer required uout = 609.5 × 1.4 × 103/(250 × 0.64) = 5333 mm Length attributable to column faces = 3 × 400 = 1200 mm = radius to uout from face of column = say (5333 − 1200)/Q = 1315 mm from face of column Perimeters of shear reinforcement may stop 1370 – 1.5 × 250 = 940 mm from face of column. d) Shear reinforcement As before, sr,max = 175 mm; st,max = 350 mm and fywd,ef = 312 MPa For perimeter u1 Asw ≥ (vEd – 0.75vRd,c) sr u1/1.5fywd,ef = (1.23 – 0.75 × 0.64) × 175 × 2771/(1.5 × 312) = 777 mm2 per perimeter Asw,min ≥ 0.08 × 300.5 (175 × 350)/(1.5 × 500) = 36 mm2 Asw/u1 ≥ 777/2771 = 0.28 mm2/mm Using H8 max. spacing = 50/0.28 = 178 mm cc =Use min. H8 (50 mm2) legs of links at 175 mm cc around perimeters: perimeters at 175 mm centres e) Check area of reinforcement > 777 mm2 in perimeters inside u1§ 1st perimeter to be > 0.3d but < 0.5d from face of column. Say 0.4d = 100 mm from face of column By inspection of Figure 3.27 the equivalent of 6 locations are available at 0.4d from column therefore try 2 × 6 no. H10 = 942 mm2

Exp. (6.54)

Cl. 6.4.5(4) & NA

Cl. 9.4.3(1), 9.4.3(2) Exp. (6.52)

Exp. (9.11)

Fig. 9.10, Cl. 9.4.3(4)

By inspection of Figure 3.27 the equivalent of 12 locations are available at 1.15d from column therefore try 12 no. H10 = 942 mm2 By inspection of Figure 3.27 the equivalent of 14 locations are available at 1.90d from column therefore try 14 no. H10 = 1099 mm2 By inspection of Figure 3.27 beyond u1 to uout grid of H10 at 175 x 175 OK.

3.4.12 Punching shear, edge column with hole Check columns D1 and D3 for 200 × 200 mm hole adjacent to column. As previously described use 4 no. H20 U-bars each side of column for transfer moment. Assuming internal support, VEd = 516.5 kN § See Commentary on design Section 3.4.14. Punching shear reinforcement is also subject to requirements for minimum reinforcement and spacing of shear reinforcement (see Cl. 9.4.3).

Cl. 9.4.3

87


a) Check at perimeter of column vEd = bVEd/uid < vRd,max where b = factor dealing with eccentricity; recommended value 1.4 VEd = applied shear force ui = control perimeter under consideration. For punching shear adjacent to edge columns u0 = c2 + 3d < c2 + 2c1 = 400 + 750 < 3 × 400 mm = 1150 mm Allowing for hole, u0 = 1150 – 200 = 950 mm d = 250 mm as before vEd = 1.4 × 516.5 × 103/950 × 250 = 3.06 MPa = OK vRd,max as before = 5.28 MPa b) Check shear stress at basic perimeter u1 (2.0d from face of column) vEd = bVEd/u1d < vRd,c where b, VEd and d as before u1 = control perimeter under consideration. For punching shear at 2d from edge column columns u1 = c2 + 2c1+ Q × 2d = 2771 mm Allowing for hole 200/(c1/2): x/(c1/2 + 2d) 200/200: x/( 200 + 500) = x = 700 mm u1 = 2771 – 700 = 2071 mm vEd = 1.4 × 516.5 × 103/2071 × 250 = 1.40 MPa vRd,c = 0.18/gC × k × (100 rlfck)0.333

Cl. 6.4.3(2), 6.4.5(3) Fig. 6.21N & NA

Cl. 6.4.5(3)

Exp. (6.32) Cl. 6.4.5(3) Note Cl. 6.4.2

Fig. 6.15

Fig. 6.14

Exp. (6.47) & NA

where gC = 1.5 k = as before = 1 + (200/250)0.5 = 1.89 rl = (r ly r lz )0.5 where rer, rlz = Reinforcement ratio of bonded steel in the y and z direction in a width of the column plus 3d each side of column rly: (perpendicular to edge) 8 no. H20 T2 + 6 no. H12 T2 in 2 × 720 + 400 − 200, i.e. 3190 mm2 in 1640 mm. =r ly = 3190/(240 × 1640) = 0.0081 rlz: (parallel to edge) 6 no. H20 T1 (5 no. are effective) + 1 no. T12 T1 in 400 + 750 – 200, i.e. 1683 mm2 in 950 mm. =r lz = 1683/(260 × 950) = 0.0068 88

Cl. 6.4.4.1(1)

,'-3?eZmleZ[

rl = (0.0081 × 0.0068)0.5 = 0.0074 = 30 fck vRd,c = 0.18/1.5 × 1.89 × (100 × 0.0074 × 30)0.33 = 0.64 MPa = punching shear reinforcement required

Table C6‡

D

3d = 750 400


H12 @ 175T1

H12 @ 200 U-bars

6H20T @ 175 3d = 750

400

3

8H20 U-bars in pairs @ 200 cc 3d = 750

Figure 3.25 Flexural tensile reinforcement adjacent to columns D1 and D3 c) Perimeter at which punching shear links no longer required uout = 516.5 × 1.4 × 103/(250 × 0.64) = 4519 mm Length attributable to column faces = 3 × 400 = 1200 mm Angle subtended by hole from centre of column D1 (See Figures 3.25 & 3.27) = 2 tan−1(100/200) = 2 × 26.5° = 0.927 rads. = radius to uout from face of column = say (4519 − 1200)/(Q − 0.927) = 1498 mm from face of column Perimeters of shear reinforcement may stop 1498 – 1.5 × 250 = 1123 mm from face of column d) Shear reinforcement As before, sr,max = 175 mm; st,max = 350 mm and fywd,ef = 312 MPa For perimeter u1 Asw ≥ (vEd – 0.75vRd,c) sr u1/1.5fywd,ef) per perimeter = (1.40 – 0.75 × 0.64) × 175 × 2071/(1.5 × 312) = 712 mm2 per perimeter

Exp. (6.54)

Cl. 6.4.5(4) & NA

Cl. 9.4.3(1) 9.4.3(2) Exp. (6.52)

Asw,min ≥ 0.08 × 300.5 (175 × 350)/(1.5 × 500) = 36 mm2 Asw/u1 ≥ 712/2071 = 0.34 mm2/mm ‡v Rd,c for various values of d and rl is available from Table C6.

89


Using H8 (50 mm2) max. spacing = min[50/0.3; 1.5d] = min[147; 375] = 147 mm cc No good Try using H10, max. spacing = 78.5/0.34 = 231 mm cc, say 175 cc = Use min. H10 (78.5 mm2) legs of links at 175 mm cc around perimeters: perimeters at 175 mm centres Check min. 9 no. H10 legs of links (712 mm2) in perimeter u1, 2d from column face. e) Check area of reinforcement > 712 mm2 in perimeters inside u1‡ 1st perimeter to be 100 mm from face of column as before. By inspection of Figure 3.27 the equivalent of 6 locations are available at 0.4d from column therefore try 2 × 6 no. H10 = 942 mm2.

Fig. 9.10, Cl. 9.4.3(4)

By inspection of Figure 3.27 the equivalent of 10 locations are available at 1.15d from column therefore try 10 H10 = 785 mm2. By inspection of Figure 3.27 beyond 1.15d to uout grid: H10 at 175 x 175 OK.

3.4.13 Summary of design Grid C flexure End supports: Column strip: (max. 200 mm from column) 10 no. H20 U-bars in pairs (where 200 × 200 hole use 8 no. H20 T1 in U-bars in pairs) Middle strip: H12 @ 200 T1 Spans 1–2 and 2–3: Column strip and middle strip:

H20 @ 200 B

Central support: Column strip centre: for 750 mm either side of support: Column strip outer: Middle strip:

H20 @ 100 T1 H20 @ 250 T1 H16 @ 200 T1

Grid 1 (and 3) flexure Spans: Column strip: Middle strip:

H16 @ 200 B2 H12 @ 300 B2

‡ See Commentary on design Section 3.4.14. Punching shear reinforcement is also subject to requirements for minimum reinforcement and spacing of shear reinforcement.

90

Cl. 9.4.3


,'-3?eZmleZ[

Interior support: Column strip centre: Column strip outer: Middle strip:

6 no. H20 @ 175 T2 H12 @ 175 T2 H12 @ 300 T2

Grid 2 flexure Spans: Column strip: Middle strip:

H16 @ 250 B2 H10 @ 200 B2

Interior support: Column strip centre: Column strip outer: Middle strip:

H20 @ 200 T2 H16 @ 250 T2 H12 @ 300 T2 See Figure 3.26

Punching shear Internal (e.g. at C2): Generally, use H10 legs of links in perimeters at max. 175 mm centres, but double up on 1st perimeter Max. tangential spacing of legs of links, st,max = 270 mm Last perimeter, from column face, min. 767 mm See Figure 3.26 Edge (e.g. at C1, C3 assuming no holes): Generally, use H10 legs of links in perimeters at max. 175 mm centres but double up on 1st perimeter Max. tangential spacing of legs of links, st,max = 175 mm Last perimeter, from column face, min. 940 mm Edge (e.g. at D1, D3 assuming 200 × 200 hole on face of column): Generally, use H10 legs of links in perimeters at max. 175 mm centres but double up on 1st perimeter Max. tangential spacing of legs of links, st,max = 175 mm Last perimeter, from column face, min. 1123 mm See Figure 3.27

91

C

D

10H20 T1 U-bars in pairs @ 200 H12 @ 200 T1 U-bars

6H20 - 175 T2 8H20 T1 U-bars in pairs @ 200

H12 - 200 T1 U-bars

1


H20 @ 200 B1

H16 @ 175 B2* 5H12 @ 175 T2

H12 @ 300 B2 H10 @ 200 T2

4H16 @ 250 T2 3H20 @ 250 T1

H16 @ 175 B2* 2

16H20 @ 100 T1

9H20 @ 175 T2* 3H20 @ 250 T1 16H20 @ 100 T1

3H20 @ 250 T1 H16 @ 200 T1 Note:* Spacing rationalised to suit punching shear links

Figure 3.26 Reinforcement details bay C–D, 1–2

3.4.14 Commentary on design a) Method of analysis The use of coefficients in the analysis would not usually be advocated in the design of such a slab. Nonetheless, coefficients may be used and, unsurprisingly, their use leads to higher design moments and shears, as shown below.

92

Method

Moment in Centre support Centre support 9.6 m span per moment per reaction VEd (kN) 6 m bay (kNm) 6 m bay (kNm)

Coefficients

842.7

952.8

1205

Continuous beam

747.0

885.6

1103

Plane frame columns 664.8 below

834.0

1060

Plane frame columns 616.8 above and below

798.0

1031

,'-3?eZmleZ[

D 375

1123

6H20 @ 175 T2 6H16 @ 175 B2

8H20 T1 U-bars in pairs uout

H10 @ 200 T1 U-bars

H10 @ 200 T1 U-bars

1

175 175

1 u1

500

175 175


175

1.5d uout

175 175 175 175 175 Ineffective area S = 152 H10 legs of links CL @ 175 mm centres 175 175 175 175 175 175 200 200 175 175 175 175 175 175 100

100

Note: For internal column see Figure 3.23

Figure 3.27 Punching shear links at column D1 (and D3) (penultimate support without hole similar) These higher moments and shears result in rather more reinforcement than when using other more refined methods. For instance, the finite element analysis used in Guide to the design and construction of reinforced concrete flat slabs[27] for this bay, leads to: t H16 @ 200 B1 in spans 1–2 (cf. H20 @ 200 B1 using coefficients) t H20 @ 125 T1 at support 2 (cf. H20 @ 100 T1 using coefficients) t 3 perimeters of shear links at C2 for VEd = 1065 kN (cf. 5 perimeters using coefficients) t 2 perimeters of shear links at C3 (cf. 7 perimeters using coefficients) b)

Effective spans and face of support In the analysis using coefficients, advantage was taken of using effective spans to calculate design moments. This had the effect of reducing span moments. At supports, one may base the design on the moment at the face of support. This is borne out by Guide to the design and construction of reinforced concrete flat slabs[27] that states that hogging moments greater than those at a distance hc/3 may be ignored (where hc is the effective diameter of a column or column head). This is in line with BS 8110[7] and could have been used to reduce support moments.

Cl. 5.3.2.2(1)

Cl. 5.3.2.2(3)

93


c)

Punching shear reinforcement Arrangement of punching shear links According to the literal definition of :lp in Exp. (6.52), the same area of shear reinforcement is required for all perimeters inside or outside perimeter n* (rather than (:lp/n*)/sr being considered as the required density of shear reinforcement on and within perimeter n*). For perimeters inside n*, it might be argued that Exp. (6.50) (enhancement close to supports) should apply. However, at the time of writing, this expression is deemed applicable only to foundation bases. Therefore, large concentrations of shear reinforcement are required close to the columns – in this example, this included doubling up shear links at the 1st perimeter.

Exp. 6.50

Similar to BS 8110[7] figure 3.17, it is apparent that the requirement for punching shear reinforcement is for a punching shear zone 1.5d wide. However, in Eurocode 2, the requirement has been ‘simplified’ in Exp. (6.52) to make the requirement for a perimeter (up to 0.75d wide). It might appear reasonable to apply the same 40%:60% rule (BS 8110 Cl. 3.7.7.6) to the first two perimeters to make doubling of punching shear reinforcement at the first perimeter unnecessary: in terms of Eurocode 2 this would mean 80% Asw on the first perimeter and 120% Asw on the second. Using this arrangement it would be possible to replace the designed H10 links in the first two perimeters with single H12 links.

BS 8110: Fig. 3.17

Outside u1, the numbers of links could have been reduced to maintain provision of the designed amount of reinforcement Asw. A rectangular arrangement of H12 links would have been possible (within perimeter u1, 350 × 175; outside u1, 500 × 175). However, as the grid would need to change orientation around each column (to maintain the 0.75d radial spacing) and as the reinforcement in B2 and T2 is essentially at 175 centres, it is considered better to leave the arrangement as a regular square grid.

Cl. 9.4.3(1)

Use of shear reinforcement in a radial arrangement, e.g. using stud rails, would have simplified the shear reinforcement requirements. VEd/VRd,c In late 2008, a proposal was made for the UK National Annex to include a limit of 2.0 or 2.5 on VEd/VRd,c (or vEd/vRd,c) within punching shear requirements. It is apparent that this limitation could have major effects on flat slabs supported on relatively small columns. For instance in Section 3.4.12, edge column with hole, VEd/VRd,c = 2.18. Curtailment of reinforcement In this design, the reinforcement would be curtailed and this would be done either in line with previous examples or, more practically, in line with other guidance[20, 21].

94

Exp. 6.52

BS 8110: Cl. 3.7.7.6

,'.3LmZbk_ebàm 3.5 Stair flight


Mabl^qZfie^bl_hkZmrib\ZelmZbk_ebàm' Ikhc^\m]^mZbel

chg

Ch[gh'

Stair flight

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

1750

600

9 @250

600

3450

Figure 3.28 Stair flight

3.5.1 Loads kN/m2

Permanent (worse case flight) Assume 160 waist 0.160 × 305/250 × 25 Treads 4 × 0.25 × 0.175/2 × 25 50 mm screed 0.5 × 22 Finishing

Variable action: crowd loading

= 4.88 = 2.19 = 1.10 = 0.03 gk = 8.20 qk = 4.00

EC1-1-1: Table 6.1, 6.2 & NA.3

3.5.2 Moment MEd = (8.20 × 1.25 + 4.00 × 1.5) × 3.452/8 = 24.2 kNm/m

3.5.3 Design d = 160 – cnom – f/2 where cnom = 25 mm (for XC1) f = 12 mm (assumed) = d = 129 mm

Concise: Table 4.2; BS 8500

95

= = z/d = z = = As = = =


K

MEd/bd2fck = 24.2 × 106/(1000 × 1292 × 30) 0.048 0.95 0.95 × 129 122 mm MEd/fydz 24.2 × 106/[(500/1.15) × 122] 456 mm2/m (r = 0.35%) Try H12 @ 250 (452 mm2/m) = OK)

Table C5

3.5.4 Check deflection Allowable l/d = N × K × F1 × F2 × F3 where N = 32.7 K = 1.0 F1 = 1.0 F2 = 1.0 F3 = 1.0 (say) = Allowable l/d = 32.7 Actual l/d = 3450/129 = 26.7 = OK

Appendix C7, Table C10 Table C11

=Provide H12 @ 250 B.

96

-'*3
- Beams -') General Ma^\Ze\neZmbhglbgmablL^\mbhgZkîk^l^gm^]bgma^_heehpbgìZkml3 -'* nkh\h]^+'


Ma^rZk^bgm^g]^]mh[^beenlmkZmbo^h_ma^
EC0 & NA Table NA.2.1

N :ll^llZ\mbhglhgma^[^Zf'

EC1 & NAs

N :ll^ll]nkZ[bebmrk^jnbk^f^gmlZg]]^m^kfbg^\hg\k^m^

Table 4.1 BS 8500–1: Tables A4, A5

lmk^g`ma' N
k^lblmZg\î^kbh]' N
EC2–1–2: Tables 5.8, 5.9, 5.10, 5.11 Cl. 4.4.1

k^jnbk^f^gml' N =^m^kfbg^pab\a\hf[bgZmbhglh_Z\mbhglZiier'

EC0 & NA Tables NA.A1.1, NA.A1.2 (B)

N =^m^kfbgêhZ]bg`ZkkZg`^f^gml'

Cl. 5.1.3(1) & NA

N :gZerl^lmkn\mnk^mhh[mZbg\kbmb\Zefhf^gmlZg]la^Zk

Cl. 5.4, 5.5, 5.6

_hk\^l' N =^lb`g_e^qnkZek^bg_hk\^f^gm'

Cl. 6.1

N
Cl. 7.4

N
Cl. 6.2

N Hma^k]^lb`g\a^\dl3

Cl. 9.3.1.1(1), 9.2.1.1(1) Cl. 7.3, Tables 7.2N, 7.3N Cl. 9.3.1.2(2) Cl. 9.3.1.1(2), 9.3.1.4(1)

N
Cl. 9.3.1.1(4), 9.2.1.3, Fig. 9.2

N
Cl. 9.3.1.2, 8.4.4, 9.3.1.1(4), 9.2.1.5(1), 9.2.1.5(2)

N
Cl. 8.7.3

97

-'* Continuous beam on pin supports Mabl \Ze\neZmbhg bl bgm^g]^] mh lahp Z mrib\Ze aZg] \Ze\neZmbhg _hk Z \hgmbgnhnl lbfier lniihkm^][^Zfnlbg`\h^_Ë\b^gmlmh]^m^kfbg^fhf^gmlZg]la^Zkl' Ikhc^\m]^mZbel


Continuous beam on pin supports

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

A 450 mm deep × 300 mm wide rectangular beam is required to support office loads of gk = 30.2 kN/m and qk = 11.5 kN/m over 2 no. 6 m spans. fck = 30 MPa, fyk = 500 MPa. Assume 300 mm wide supports, a 50-year design life and a requirement for a 2-hour resistance to fire in an external but sheltered environment. qk = 11.5 kN/m gk = 30.2 kN/m 6000

6000

Figure 4.1 Continuous rectangular beam

450

300

Figure 4.2 Section through beam

4.1.1 Actions Permanent gk = 30.2 kN/m and variable qk = 11.5 kN/m

4.1.2 Cover Nominal cover, cnom: cnom = cmin + Dcdev where cmin = max[cmin,b; cmin,dur] where cmin,b = minimum cover due to bond = diameter of bar. Assume 25 mm main bars cmin,dur = minimum cover due to environmental conditions. Assuming XC3 (moderate humidity or cyclic wet and dry) and secondarily XF1 (moderate water

98

Exp. (4.1)

Cl. 4.4.1.2(3)

-'*3

cmin,dur

saturation without de-icing salt) using C30/37 concrete, = 25 mm

Table C3 BS 8500-1[14]: Table A4; How to: Building structures[8]

Dcdev = allowance in design for deviation. Assuming no measurement of cover, Dcdev= 10 mm = cnom = 25 + 10 = 35 mm

Cl. 4.4.1.2(3)

Fire: Check adequacy of section for 2 hours fire resistance (i.e. REI = 120) = OK For bmin = 300 mm, minimum axis distance, a = 35 mm cnom = 35 mm

EC2-1-2: 5.6.3(1), Table 5.6

4.1.3 Load combination (and arrangement) Load combination: By inspection, BS EN 1990 Exp. (6.10b) governs = n = 1.25 × 30.2 + 1.5 × 11.5 =

50.8 kN/m

Fig. 2.5 EC0: Exp.(6.10b)

Arrangement: Choose to use all-and-alternate-spans-loaded load cases, i.e. use coefficients.

Cl. 5.1.3(1) & NA Table NA.1 (option b) Table C3

The coefficients used assume 15% redistribution at supports. As the amount of redistribution is less than 20%, there are no restrictions on reinforcement grade. The use of Table 5.6 in BS EN 1992–1–2 is restricted to where redistribution does not exceed 15%.

Table C3 Cl. 5.5(4) & NA EC2-1-2: 5.6.3(1), Table 5.6

4.1.4 Analysis Design moments: Spans MEd = (1.25 × 30.2 × 0.090 + 1.5 × 11.5 × 0.100) × 6.02 = 122.3 + 62.1 = 184.4 kNm Support MEd = 50.8 × 0.106 × 6.02 = 193.8 kNm

Appendix C1, Table C3 Table C3

Shear force: VAB = 0.45 × 6.0 × 50.8 = 137.2 kN VAB = 0.63 × 6.0 × 50.8 = 192.0 kN

4.1.5 Flexural design Effective depth: Assuming 10 mm links: d = 450 − 35 − 10 − 25/2 = 392 mm 99


Flexure in span: K = MEd/bd2fck = 184.4 × 106/(300 × 3922 × 30) = 0.133 z/d = 0.864 z = 0.864 × 392 = 338 mm As = MEd/fydz = 184.4 × 106/(434.8 × 338) = 1255 mm2 Try 3 no. H25 B (1473 mm2) (r = 1.25%) Check spacing: Spacing of outer bars = 300 – 2 × 35 − 2 × 10 – 25 = 185 mm Assuming 10 mm diameter link, = spacing = 98 mm Steel stress under quasi-permanent loading: ss = (fyk /gS) (As,req/As,prov) (SLS loads/ULS loads) (1/d) = fyd × (As,req/As,prov) × (gk + c2 qk)/(gGgk + gQqk) (1/d) = (500/1.15) × (1255/1473) × [(30.2 + 0.3 × 11.5)/50.8] (1/1.03) = 434.8 × 0.91 × 0.66 × 0.97 = 237 MPa As exposure is XC3, max. crack width wmax = 0.3 mm = Maximum bar size = 16 mm or max. spacing = 200 mm = OK = Use 3 H25 B (1473 mm2) Deflection: Check span-to-effective-depth ratio. Basic span: effective depth ratio for r = 1.25%: l/d = 18 + [(1.25 – 0.5)/(1.5/0.5)] × (26 – 18) = 24.0 Max. span = 24.0 × 392 = 9408 mm = OK

Fig. 3.5 Appendix A1 Table C5

Cl. 7.3.3(2) Cl. 7.3.1(5) & NA Table 7.2N & NA

Appendix B Table 7.4N & NA

Flexure, support: MEd = 193.8 kNm K = MEd/bd2fck where d = 450 − 35 − 10 − 25/2 = 392 mm K = 193.8 × 106/(300 × 3922 × 30) = 0.142 By inspection, K ≤ K' (0.142 × 0.168‡) = no compression reinforcement required. z = 0.85d = 0.85 × 392 = 333 mm As = MEd/fydz = 193.8 × 106/434.8 × 333 = 1338 mm2 Try 3 no. H25 T (1473 mm2) (r = 1.13%) ‡ K' is limited to 0.208. However, if, as is usual practice in the UK, x/d is limited to 0.45, z/d is as a consequence limited to 0.82 and K' to 0.168.

100

Appendix A1 Table C5

-'*3
4.1.6 Shear


a) Support B (critical) Shear at central support = 192.0 kN At d from face of support§ VEd = 192.0 − (0.300/2 + 0.392) × 50.8 = 164.50 kN vEd = VEd /bd = 164.5 × 103/(392 × 300) = 1.40 MPa Maximum shear capacity: Assuming fck = 30 MPa and cot y = 2.5# vRd,max* = 3.64 MPa vRd,max > vEd = OK

Cl. 6.2.1(8)

Table C7

Shear reinforcement: Assuming z = 0.9d Asw /s ≥ VEd /(0.9d × fywd × cot y) ≥ 164.5 × 103/(0.9 × 392 × (500/1.15) × 2.5) = 0.429

Cl. 6.2.3(1) Cl. 6.2.3(3), Exp. (6.8)

More accurately, Asw/s ≥ VEd/(z × fywd × cot y) ≥ 164.5 × 103/(333 × 1087) = 0.454

Cl. 6.2.3(3), Exp. (6.8)

Minimum shear links, Asw,min/s = 0.08bwfck0.5/fyk = 0.08 × 300 × 300.5/500 = 0.263. Not critical Max. spacing = 0.75d = 0.75 × 392 = 294 mm Use H8 @ 200 (Asw /s = 0.50) b) Support A (and C) Shear at end support = 137.2 kN At face of support, VEd = 137.2 − (0.150 + 0.392) × 50.8 = 109.7 kN By inspection, shear reinforcement required and cot y = 2.5 Asw /s ≥ VEd/(z × fywd × cot y) ≥ 109.7 × 103/[353 × (500/1.15) × 2.5] = 0.285 Use H8 @ 200 (Asw /s = 0.50) throughout‡

§

Where applied actions are predominantly uniformly distributed, shear may be checked at d from the face of support. See also Section 4.2.11.

Cl. 9.2.2(5) Cl. 9.2.2(6)

Cl. 6.2.1(8) Fig. C1a) Appendix C5.3

Cl. 6.2.1(8)

# The absolute maximum for v Rd,max (and therefore the maximum value of vEd) would be 5.28 MPa when cot y would equal 1.0 and the variable strut angle would be at a maximum of 45°.

* For determination of VRd,max see Section 4.2.10. ‡ As maximum spacing of links is 294 mm, changing spacing of links would appear to be of limited benefit.

101

4.1.7 Summary of design H8 @ 200 centres in 2 legs 3H25

A

3H25B

B

3H25B

C


Figure 4.3 Continuous rectangular beam: Summary of design Commentary It is usually presumed that the detailer would take the design summarised above and detail the beam to normal best practice[8,9]. The design would go no further where standard detailing is all that is required. Where the element is non-standard (e.g. where there are point loads), it should be incumbent on the designer to give the detailer specific information about curtailment, laps, etc. as illustrated below. The detailer’s responsibilities, standards and timescales should be clearly defined but it would be usual for the detailer to draw and schedule not only the designed reinforcement but all the reinforcement required to provide a compliant and buildable solution. The work would usually include the checking the following aspects and providing appropriate detailing: t Minimum areas t Curtailment lengths t Anchorages t Laps t U-bars t Rationalisation t Critical dimensions t Details and sections The determination of minimum reinforcement areas and curtailment lengths, using the principles in Eurocode 2 is shown below. In practice these would be determined from published tables of data or by using reference texts[8,9]. Nonetheless, the designer should check the drawing for design intent and compliance with the standards. It is therefore necessary for the designer to understand and agree the principles of the detailing used.

4.1.8 Detailing checks a) Minimum areas As,min = 0.26(fctm/fyk)btd ≥ 0.0013btd where 102

Cl. 9.2.1.1

-'*3
bt = width of tension zone fctm = 0.30 × fck0.666

Table 3.1


As,min = 0.26 × 0.30 × 300.666 × 300 × 392/500 = 177 mm2 b) Curtailment of main bars Bottom: curtail 75% main bars 0.08l from end support = 480 mm say 450 mm from A 70% main bars 0.30l – al = 0.3 × 6000 − 1.125 × d = 1800 − 1.125 × 392 = 1359 mm say 1350 from A Top: curtail 40% main bars 0.15l + al = 900 + 441 = 1341 mm say 1350 from B 65% main bars 0.30l + al = 1800 + 441 = 2241 mm say 2250 from B

How to: Detailing

At supports: 25% of As to be anchored at supports 25% of 1225 mm2 = 314 mm2 Use min. 2 no. H16 (402 mm2) at supports A, B and C

Cl. 9.2.1.2.(1), 9.2.1.4(1) & NA Cl. 9.2.1.5(1)

In accordance with SMDSC[9] detail MB1 lap U-bars tension lap with main steel = 780 mm (in C30/37 concrete, H12, ‘poor’ bond condition) = say 800 mm

How to: Detailing

c) Summary of reinforcement details 2H12T

3H25 100 800 1350

2H16 U-bars

2H12

2H25 2H12 1H25

3H25 2H16 A 450 800

2H12 2H25 1H25

3H25B

2H12T

1350

100 800

1250

2H12

1H25 2H12 2H25 1H25 2H25 2H12

B 800 600 750 750 600 800 2H16B

2H16 U-bars

2H16 2H25 C 800 450 3H25B

Links omitted for clarity

Figure 4.4 Continuous rectangular beam: reinforcement details Note Subsequent detailing checks may find issues with spacing rules especially if the 'cage and splice bar' method of detailing were to be used. 2H32s T&B would be a suitable alternative to 3H25s T&B.

103

-'+ Heavily loaded L-beam Ikhc^\m]^mZbel

Heavily loaded L-beam

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

Gk2 = 88.7 Qk2 = 138.7 gk1 = 46.0 qk1 = 63.3


A

B

C

2000 9000

8000

Figure 4.5 Heavily loaded L-beam This edge beam supports heavy loads from storage loads. The variable point load is independent of the variable uniformly distributed load. The beam is supported on 350 mm square columns 4000 mm long. fck = 30 MPa; fyk = 500 MPa. The underside surface is subject to an external environment and a 2-hour fire resistance requirement. The top surface is internal and subject to a 2-hour fire resistance requirement. Assume that any partitions are liable to be damaged by excessive deflections. beff

750

350

Figure 4.6 Section through L-beam

4.2.1 Actions Permanent: UDL from slab and cladding gk = 46.0 kN/m Point load from storage area above = 88.7 kN Variable: From slab qk = 63.3 kN/m Point load from storage area above = 138.7 kN 104

CCIP – 041 1 Oct 09

-'+3A^ZoberehZ]^]E&[^Zf

4.2.2 Cover


a) Nominal cover, cnom, underside and side of beam cnom = cmin + Dcdev where cmin = max[cmin,b ; cmin,dur] where cmin,b = minimum cover due to bond = diameter of bar. Assume 32 mm main bars and 10 mm links cmin,dur = minimum cover due to environmental conditions. Assuming primarily XC3/XC4 exposure (moderate humidity or cyclic wet and dry); secondarily XF1 exposure (moderate water saturation without de-icing salt, vertical surfaces exposed to rain and freezing) and C30/37 concrete, cmin,dur = 25 mm Dcdev = allowance in design for deviation. Assuming no measurement of cover Dcdev = 10 mm

Exp. (4.1)

Cl. 4.4.1.2(3)

Table 4.1 BS 8500-1: Table A4

Cl. 4.4.1.2(3)

= cnom = 32 + 10 = 42 mm to main bars or = 25 + 10 = 35 mm to links Use cnom = 35 mm to links (giving cnom = 45 mm to main bars) b) Fire Check adequacy of section for 2 hours fire resistance REI 120. By inspection, web thickness OK. Axis distance, a, required = 35 mm OK by inspection.

EC2-1-2: 5.6.3 EC2-1-2: Table 5.6 EC2-1-2: Table 5.6

= Try 35 mm nominal cover bottom and sides to 10 mm link. Nominal cover, cnom, top: By inspection, cnom = cmin + Dcdev

Exp. (4.1)

where cmin = max[cmin,b; cmin,dur] where cmin,b = minimum cover due to bond = diameter of bar. Assume 32 mm main bars and 10 mm links cmin,dur = minimum cover due to environmental conditions. Assuming primarily XC1 and C30/37 concrete, cmin,dur = 15 mm

Cl. 4.4.1.2(3)

Table 4.1 BS 8500-1: Table A4

105


Dcdev = allowance in design for deviation. Assuming no measurement of cover Dcdev = 10 mm = cnom = 32 + 10 = 42 mm to main bars or = 15 + 10 = 25 mm to links Use cnom = 35 mm to links (giving cnom = 45 mm to main bars)

Cl. 4.4.1.2(3)


4.2.3 Idealisation, load combination and arrangement Load combination: As loads are from storage, Exp. (6.10a) is critical.

Table 2.5; ECO: A1.2.2, NA & Exp. (6.10a)

Idealisation: This element is treated as a continuous beam framing into columns 350 × 350‡ × 4000 mm long columns below.

Cl. 5.3.1(3)

Arrangement: Choose to use all-and-alternate-spans-loaded.


4.2.4 Analysis Analysis by computer (spreadsheet TCC 41 Continuous Beam (A+D).xls in RC spreadsheets V.3[28] assuming frame action with 350 mm square columns 4 m long fixed at base. Beam inertia based on T-section, beff wide) with 15% redistribution at central support, limited redistribution of span moment and consistent redistribution of shear.

ECO: A1.2.2 & NA; Cl. 5.3.1 (6)

Table 4.2 Elastic and redistributed moments, kNm Span number Elastic M Redistributed M d

1 1168 1148 0.98

2 745 684 0.92

2000 1394 kNm

1500 1000 500 195 kNm

108 kNm

0 A

B

C

– 500 – 684 kNm

–1000 – 1500

–1148 kNm

Figure 4.7 Redistributed envelope, kNm ‡ Note:

350 × 350 is a minimum for columns requiring a fire resistance of 120 minutes.

106

EC2-1-2: Table 5.2a

1000 646 kN

794 kN

500

0 A

B

– 500

C – 499 kN


– 1000 – 1098 kN – 1500

4.2.5 Flexural design, support A MEd = 195 kNm in hogging MEd,min = 1148 × 0.25 in hogging and in sagging = 287 kNm K = MEd/bd2fck where b = beff = beff1 + bw + beff2 where beff1 = (0.2b1 + 0.1l0) ≤ 0.2 l0 ≤ b1 where b1 = distance between webs/2 l0 = nominal: assume 0§ = beff1 = 0 mm = beff2 =b = bw = 350 mm d = 750 − 35 – 10 – 32/2 = 689 mm assuming 10 mm link and H32 in support. fck = 30 MPa K = 287 × 106/(350 × 6892 × 30) = 0.058 Restricting x/d to 0.45 K' = 0.168 K ≤ K' = section under-reinforced and no compression reinforcement required. z = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d = (689/2) (1 + 0.89) ≤ 0.95 × 689 = 652 ≤ 654 = z = 652 mm As = MEd/fydz §

The distance l0 is described as the distance between points of zero moment, ‘which may be obtained from Figure 5.2’. In this case l0 = 0. (see Figure 4.11).

Cl. 9.2.1.2(1), 9.2.1.4(1) & NA

Cl. 5.3.2.1, Fig. 5.3

Fig. 5.2

Appendix A1

Appendix A1

Cl. 5.3.2.1(2) Fig. 5.2 Fig. 4.11 107

where fyd = 500/1.15 = 434.8 MPa = 287 × 106/(434.8 × 652) = 1012 mm2 Try 2 no. H32 U-bars (1608 mm2) Check anchorage of H32 U-bars. Bars need to be anchored distance ‘A’ into column

SMDSC: 6.4.2


U-bar

A

Figure 4.9 Distance A Assuming column uses 35 mm cover, 10 mm links and 32 mm bars: Distance A = 2 [350 − 2 (35 + 10) ] − 32/2 − 32/2 + 750 – [2 (35 + 10)] − 2 × 32/2 – (4 − π) (3.5 + 0.5) × 32 = 488 + 628 – 110 = 1006 mm Anchorage length, lbd = alb,rqd ≥ lb,min

SMDSC[9], BS 8666[19]: Table 2 Cl. 8.4.4, Exp. (8.4)

where a = conservatively 1.0 lb,rqd = (f/4) (ssd/fbd)

Exp. (8.3)

where f = 32 ssd = design stress in the bar at the ULS = 434.8 × 1012/1608 = 274 MPa f[] = ultimate bond stress = 2.25 n1 n2 fct,d

108

Cl. 8.4.2 (2)


where n1 = 1.0 for good bond conditions n2 = 1.0 for bar diameter ≤ 32 mm fct,d = act fctk/ gC = 1.0 × 2.0/1.5 = 1.33 MPa fbd = 2.25 × 1.33 = 3.0 MPa


lb,rqd = (32/4) (274/3.0) = 731 mm‡ lb,min = max[10f; 100 mm] = 250 mm = lbd = 731 mm i.e. < 1006 mm

Cl. 3.1.6 (2), Tables 3.1 & 2.1, & NA

= OK Use 2 no. H32 U-bars

4.2.6 Flexural design, span AB a) Span AB – Flexure MEd = 1148 kNm K = MEd/bd2fck where b = beff = beff1 + bw + beff2 where beff1 = (0.2b1 + 0.1l0) ≤ 0.2 l0 ≤ b1 where b1 = distance between webs/2 Assuming beams at 7000 mm cc = (7000 – 350)/2 = 3325 mm l0 = 0.85 × l1 = 0.85 × 9000 = 7650 mm§

Cl. 5.3.2.1, Fig. 5.3

Fig. 5.2

beff beff,2

beff,1 bw

bw b1

b1

b2

b2

b

Figure 4.10 Effective flange width beff ‡ Anchorage lengths may be obtained from published tables. In this instance, a figure of 900 mm may be obtained from Table 13 of Section 10 of How to design concrete structures using Eurocode 2. § The

distance l0 is described as the distance between points of zero shear, which may be obtained from Figure 5.2’. From the analysis, l0 could have been taken as 7200 mm.

Fig. 5.3

How to: Detailing[8] Cl. 5.3.2.1(2) Figure 5.2 109

I0 = 0.85 I1 I1

I0 = 0.15 (I1+I2)

I0 = 0.7 I2


I3

l0 for calculation of

flange width beff1 = = = bw = beff2 =

I0 = 0.15 (I2+I3)

I2

Fig. 5.2 0.2 × 3325 + 0.1 × 7650 ≤ 0.2 × 7650 ≤ 3325 1430 ≤ 1530 ≤ 3325 1430 mm 350 mm (0.2b2 + 0.1l0) ≤ 0.2 l0 ≤ b2

where b2 = 0 mm beff2 = 0 mm b = 1430 + 350 + 0 = 1780 mm d = effective depth = 750 − 35 – 10 – 32/2 = 689 mm assuming 10 mm link and H32 in span fck = 30 MPa K = 1148 × 106/(1780 × 6892 × 30) = 0.045 Restricting x/d to 0.45, K' = 0.168 K ≤ K' = section under-reinforced and no compression reinforcement required. z = lever arm = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d = (689/2) (1 + 0.917) ≤ 0.95 × 689 = 661 ≤ 654 = z = 654 mm But z = d – 0.4x = by inspection, neutral axis is in flange and as x < 1.25 hf , design as rectangular section. As = MEd/fydz where fyd = 500/1.15 = 434.8 MPa = 1148 × 106/(434.8 × 654) = 4037 mm2 Try 5 no. H32 B (4020 mm2) (say OK) Check spacing of bars. Spacing of bars = [350 – 2 × (35 + 10) – 32]/(5 – 1) = 57 Clear spacing = 57 – 32 mm = 25 mm between bars 110

Appendix A1

Appendix A1

Appendix A1



Minimum clear distance between bars = max[bar diameter; aggregate size + 5 mm] = max[32; 20 + 5] = 32 mm i.e. > 25 mm = 5 no. H32 B no good For 4 bars in one layer, distance between bars = 44 mm so Try 4 no. H32 B1 + 2 no. H32 B3

Cl. 8.2(2) & NA

300

d 35 cover 400 32 bar 32 spacers 32 bar 10 link 35 cover 350

Figure 4.12 Span AB bottom reinforcement d = 750 − 35 – 10 – 32/2 – 0.333 × 2 × 32 = 668 mm K = 1148 × 106/(1780 × 6682 × 30) = 0.048 K ≤ K' = section under-reinforced and no compression reinforcement required.

Appendix A1

z = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d = (668/2) (1 + 0.911) ≤ 0.95 × 668 = 639 ≤ 635 = z = 635 mm

Appendix A1

= by inspection, neutral axis in flange so design as rectangular section.

Appendix A1

As = MEd/fydz = 1148 × 106/(434.8 × 635) = 4158 mm2 = 4 no. H32 B1 + 2 no. H32 B3 (4824 mm2) OK b) Span AB – Deflection Check end span-to-effective-depth ratio. Allowable l/d = N × K × F1 × F2 × F3 where N = Basic l/d: check whether r > r0 and whether to use Exp. (7.16a) or (7.16b)

Appendix B Appendix C7 Cl. 7.4.2(2), Exp. (7.16a), Exp. (7.16b) 111


N = = = K = F1 =

r = As/Ac‡ = As,req/[bwd + (beff – bw)hf] = 4158/[350 × 668 + (1780 – 350) × 300] = 4158/662800 = 0.63% r0 = fck0.5/1000 = 300.5/1000 = 0.55% r > r0 = use Exp. (7.16b)

PD 6687[6]

11 + 1.5fck0.5 r0/(r – r' ) + fck0.5(r'/r0)0.5/12 11 + 1.5 (300.5 × 0.055/(0.063 – 0) + 300.5(0/0.55)1.5 11 + 7.2 + 0 = 18.2 (end span) = 1.3 (beff/bw = 1780/350 = 5.1) = 0.80

Exp. (7.16b)

F2 = 7.0/leff (span > 7.0 m) where leff = 9000 mm F2 = 7.0/9.0 = 0.77 F3 = 310/ss ≤ 1.5

where ss in simple situations = (fyk/gS) (As,req/As,prov) (SLS loads/ ULS loads) (1/d). However in this case separate analysis at SLS would be required to determine ss. Therefore as a simplification use the conservative assumption: 310/ss = (500/fyk) (As,req/As,prov) = (500/500) × (4824/4158) = 1.16 = Permissible l/d = 18.2 × 1.3 × 0.80 × 0.77 × 1.16 = 16.9 Actual l/d = 9000/668 = 13.5 Permissible more than actual = OK = 4 no. H32 B1 + 2 no. H32 B3 (4824 mm2) OK

Table 7.4N & NA Cl. 7.4.2(2), Appendix C7 Cl. 7.4.2(2) Cl. 5.3.2.2(1) Cl. 7.4.2, Exp. (7.17), Table 7.4N & NA, Table NA.5 Note 5 Appendix B

Exp. (7.17)

4.2.7 Flexural design, support B At centreline of support B, M = 1394 kNm From analysis, at face of support MEdBA = 1209 kNm MEdBC = 1315 kNm K = MEd/bwd 2fck ‡ 2.18 of PD 6687[6] suggests that r in T sections should be based on the area of concrete above the centroid of the tension steel.

112

Cl. 5.3.2.2(3)



where bw = 350 mm d = 750 − 35 – 12 – 32/2 = 687 mm assuming 10 mm link and H32 in support but allowing for H12 T in slab fck = 30 MPa = K = 1315 × 106/(350 × 6872 × 30) = 0.265 for d = 0.85, K' = 0.168: to restrict x/d to 0.45, K' = 0.167 = Compression steel required z = (d/2) [1 + (1 − 3.53 K')0.5] = (687/2) [1 + (1 − 3.53 × 0.167)0.5] = (687/2) (1 + 0.64) < 0.95d = 563 mm As2 = (K – K')fckbd2/fsc(d − d2) where d2 = 35 + 10 + 32/2 = 61 mm fsc = 700(x − d2)/x < fyd

Appendix A1 Table C4

Fig. 3.5, Appendix A1, How to: Beams

where x = 2.5 (d – z) = 2.5 (687 – 563) = 310 mm fsc = 700 × (310 − 61)/310 < 500/1.15 = 562 MPa but limited to ≤ 434.8 MPa =As2 = (0.265 – 0.167) × 30 × 350 × 687 2/[434.8(687 − 61) ] = 1784 mm2 Try 4 no. H25 B (1964 mm2) As = M'/fydz + As2 fsc/fyd = K' fck bd 2 /(f yd z) + As2 fsc/fyd = 0.167 × 30 × 350 × 6872/(434.8 × 563) + 1570 × 434.8/434.8 = 3380 + 1784 = 5164 mm2 Try 4 no. H32 T + 4 no. H25 T (5180 mm2)

Appendix A1

This reinforcement should be spread over beff. beff = beff1 + bw + beff2

Cl. 9.2.1.2(2), Fig. 9.1 Cl. 5.3.2.1, Fig. 5.3

where beff1

= (0.2b1 + 0.1l0) ≤ 0.2 l0 ≤ b1

where b1 = distance between webs/2. Assuming beams at 7000 mm cc = (7000 – 350)/2 = 3325 mm l0 = 0.15 × (l1 + l2) = 0.15 × (9000 + 8000) = 2550 mm

Fig. 5.2

113

=beff1 = = = bw = beff2 =

0.2 × 3325 + 0.1 × 2550 ≤ 0.2 × 2550 ≤ 3325 920 ≤ 510 ≤ 3325 510 mm 350 mm (0.2b2 + 0.1l0) ≤ 0.2 l0 ≤ b2

where b2 = 0 mm beff2 = 0 mm


= beff = 510 + 350 + 0 = 860 mm Use 4 no. H32 T + 4 no. H25 T (5180 mm2) @ approx 100 mm cc beff = 860 mm

4H32

4H25

4H25

bw = 350 mm

Figure 4.13 Support pp B reinforcement

4.2.8 Flexural design, span BC a) Span BC – Flexure MEd = 684 kNm K = MEd/bd2fck where b = beff = beff1 + bw + beff2 where beff1 = (0.2b1 + 0.1l0) ≤ 0.2 l0 ≤ b1 where b1 = distance between webs/2. Assuming beams at 7000 mm cc = (7000 – 350)/2 = 3325 mm l0 = 0.85 × l1 = 0.85 × 8000 = 6800 mm beff1 = 0.2 × 3325 + 0.1 × 6800 ≤ 0.2 × 6800 ≤ 3325 = 1345 ≤ 1360 ≤ 3325 = 1360 mm 114

Cl. 5.3.2.1, Fig. 5.3

Fig. 5.2



bw = 350 mm beff2 = (0.2b2 + 0.1l0) ≤ 0.2 l0 ≤ b2 where b2 = 0 mm beff2 = 0 mm = b = 1360 + 350 + 0 = 1710 mm d = 750 − 35 – 10 – 32/2 = 689 mm assuming 10 mm link and H32 in span. fck = 30 MPa = K = 684 × 106/ (1710 × 6892 × 30) = 0.028 By inspection, K ≤ K' = section under-reinforced and no compression reinforcement required.

Appendix A1

z = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d = (689/2) (1 + 0.95) ≤ 0.95 × 689 = 672 > 655 = z = 655 mm

Appendix A1

By inspection, x < 1.25 hf ; design as rectangular section

Appendix A1

As = MEd/fydz = 684 × 106/(434.8 × 655) = 2402 mm2 Try 2 no. H32 B + 2 no. H25 B (2590 mm2) b) Span BC – Deflection By inspection, compared with span AB

OK

4.2.9 Flexural design, support C By inspection, use 2 no. H25 U-bars as support A. Use 2 no. H25 U-bars

4.2.10 Design for beam shear, support A At d from face of support VEd = 646 − (350/2 + 0.689) × (1.35 × 46.0 + 1.5 × 63.3)

= 646 – 0.864 × 157.1 = 510.3 kN Check maximum shear resistance. VRd, max = acw bw zvfcd/(cot y + tan y) where acw = 1.0 bw = 350 mm as before z = 0.9d

Cl. 6.2.1(8) ECO: A1.2.2, NA & Exp. (6.10a)

Exp. (6.9) & NA Cl. 6.2.3 & NA Cl. 6.2.3(1)

115


v

= 0.6 (1 − fck/250) = 0.6 (1 − 30/250) = 0.528

fcd = 30/1.5 = 20.0 MPa y = angle of inclination of strut. = 0.5 sin−1 {vEd,z /[0.20 fck (1 – fck /250) ] } ≥ cot−12.5 where vEd,z = VEd/bz = VEd /(b × 0.9d) = 510.3 × 103/(350 × 0.9 × 689) = 2.35 MPa y = 0.5 sin−1 {2.35/[0.20 × 30 (1 – 30/250) ] } ≥ cot−12.5 = 0.5 sin−1 (0.445) ≥ cot−12.5 = 0.5 × 26.4° ≥ 21.8° = 21.8° = VRd,max = 1.0 × 350 × 0.90 × 689 × 0.528 × 20.0/(2.5 + 0.4) = 790 kN = OK Shear reinforcement: Shear links: shear resistance with links VRd,s = (Asw /s) z fywd cot y = Asw /s ≥ VEd/z fywd cot y where Asw/s = area of legs of links/link spacing z = 0.9d as before fywd = 500/1.15 = 434.8 cot y = 2.5 as before Asw/s ≥ 510.3 × 103/(0.9 × 689 × 434.8 × 2.5) = 0.76 Minimum Asw/s = rw,minbwsin a where rw,min = 0.08 × fck0.5/fyk = 0.08 × 300.5/500 bw a

Cl. 6.2.3(3) Note 1, Exp. (6.6N) & NA Cl. 2.4.2.4(1) & NA Exp. (6.9), Appendix A2

Exp. (6.8)

Cl. 2.4.2.4(1) & NA

Cl. 9.2.2(5), Exp. (9.4) Exp. (9.5N) & NA

= 0.00088 = 350 mm as before = angle between shear reinforcement and the longitudinal axis. For vertical reinforcement sin a = 1.0

= Minimum Asw/s = 0.00088 × 350 × 1 = 0.03 But, maximum spacing of links longitudinally = 0.75d = 516 mm = Try H10 @ 200 cc in 2 legs (Asw /s = 0.78)

Cl. 9.2.2(6)

4.2.11 Design for high beam shear, support B As uniformly distributed load predominates consider at d from face of support.

116

Cl. 6.2.1(8)


VEd = 1098 − (350/2 + 0.689) × (1.35 × 46.0 + 1.5 × 63.3) = 1098 – 0.864 × 157.1 = 962.3 kN By inspection, shear reinforcement required and cot y < 2.5.


Check VRd, max (to determine y) Check maximum shear resistance. As before, VRd, max = a\p bw zvfcd/(cot y + tan y). where acw, bw, z, v and fcd as before y = 0.5 sin−1 {vEd,z/[0.20 fck (1 – fck/250) ] } ≥ cot−12.5 where vEd,z = VEd/bz = VEd/(b0.9d) = 962.3 × 103/(350 × 0.9 × 687) = 4.45 MPa y = 0.5 sin−1 {4.45/[0.20 × 30 (1 – 30/250) ] } ≥ cot−12.5 = 0.5 sin−1 (0.843) ≥ cot−12.5 = 0.5 × 57.5° ≥ 21.8° = 28.7° cot y = 1.824 i.e. > 1.0 =OK tan y = 0.548 = VRd,max = 1.0 × 350 × 0.90 × 687 × 0.528 × 20.0/(1.824 + 0.548) = 963.4 kN OK (i.e. VRd,max ≈ VEd) Shear reinforcement: Shear links: shear resistance with links VRd,s = (Asw/s)zfywd cot y = Asw/s ≥ VEd/zfywd cot y Asw/s ≥ 962.3 × 103/(0.9 × 687 × 434.8 × 1.824) = 1.96 = Use H10 @ 150 cc in 4 legs (Asw /s = 2.09)

4.2.12 Design for beam shear (using design chart), support BC

At d from face of support, VEd = 794 – 0.864 × 157.1 = 658.3 kN vEd,z = VEd/bz = VEd/(b0.9d) = 658.3 × 103/ (350 × 0.9 × 687) = 3.04 MPa From chart Asw /sreqd/m width = 2.75 Asw /sreqd = 2.75 × 0.35 = 0.96 = Use H10 in 2 legs @ 150 mm cc (Asw/s = 1.05)

Exp. (6.9) & NA

Exp. (6.9) Cl. 6.2.3(1) Exp. (6.9)

Cl. 6.2.3(2) & NA

Exp. (6.8)

Cl. 6.2.1(8)

Fig. C1b)

117

4.2.13 Check shear capacity for general case In mid span use H10 in 2 legs @ 300 mm cc (Asw/s = 0.52)


z Asw/sreqd/m width = 1.48 and an allowable vEd,z = 1.60 MPa z 1.60 × 350 × 0.90 × 687 = VEd = 346 kN

Fig. C1b)

From analysis, VEd = 346.2 kN occurs at: (646 − 346)/157.1 = 1900 mm from A, (1098 – 346 − 1.25 × 88.7 – 1.5 × 138.7)/157.1 = 2755 mm from BA, (794 − 346)/157.1 = 2850 mm from BC and (499 − 346)/157.1 = 970 mm from C

4.2.14 Summary of design 1 H10 links in 2 legs @ 150cc 2H32 U-bars

4H32 + 4H25T

2H25 U-bars

H10 links in 2 legs

@ 150

@ 300

@ 150

@ 150

4H32 B1 + 2H32 B3

4H25B

A

B 1950

2850

2850 1

Figure 4.14 Summary of L-beam design

4H32

4H25

350

510

H10 in 4 legs @ 150

Figure 4.15 L-beam section 1–1

118

@ 300

@ 150

2H32 + 2H25B C 1050

-',3

Continuous wide T-beam

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

qk = 45.8 kN/m gk = 47.8 kN/m A

B


7500

C 7500

D 7500

E 7500

Figure 4.16 Continuous wide T-beam This central spine beam supports the ribbed slab in Example 3.3. The 300 mm deep ribbed slab is required for an office to support a variable action of 5 kN/m2. The beam is the same depth as the slab and is supported on 400 mm square columns, see Figure 4.17. fck = 35 MPa; fyk = 500 MPa. A 1-hour fire resistance is required in an internal environment. Assume that partitions are liable to be damaged by excessive deflections. CL

100 200

1000

200

800

Figure 4.17 Section through T-beam

4.3.1 Actions Permanent, UDL‡: From analysis of slab, gk = 47.8 kN/m Variable: From analysis of slab, qk = 45.8 kN/m ‡ The actions may also have been estimated assuming an elastic reaction factor of 1.1 for the slab viz: kN/m Permanent: UDL Loads from ribbed slab (7.50 + 9.0)/2 × 4.30 × 1.1 = 39.0 Self-weight/patch load extra over solid 2.0 × 4.17 = 8.3 47.3 Variable: Imposed (7.50 + 9.0)/2 × 5.00 × 1.1 = 45.4

119

4.3.2 Cover Nominal cover, cnom: cnom = cmin + Dcdev

Exp. (4.1)


where cmin = max[cmin,b; cmin,dur] where cmin,b = minimum cover due to bond = diameter of bar. Assume 25 mm main bars and 8 mm links cmin,dur = minimum cover due to environmental conditions. Assuming XC1 and C30/37 concrete, cmin,dur = 15 mm Dcdev = allowance in design for deviation. Assuming no measurement of cover Dcdev = 10 mm = cnom = 15 + 10 = 25 mm to links or = 25 + 10 = 35 mm to main bars Use 10 mm diameter links to give cnom = 35 mm to main bars and 25 mm to links (as per ribbed slab design). Fire: Check adequacy of section for REI 60. Axis distance required: Minimum width bmin = 120 mm with a = 25 mm or bmin = 200 mm with a = 12 mm = at 2000 mm wide (min.) a < 12 mm By inspection, not critical. Use 25 mm nominal cover to links

Cl. 4.4.1.2(3) Table 4.1 BS 8500-1; Table A4 Cl. 4.4.1.2(3)

EC2-1-2: 5.6.3 EC2-1-2: Table 5.6 EC2-1-2: Table 5.6

4.3.3 Idealisation, load combination and arrangement Load combination: By inspection, Exp. (6.10b) is critical. 47.8 × 1.25 + 45.8 × 1.5 = 128.5 kN/m‡

Fig. 2.5 EC0: Exp. (6.10b)

Idealisation: This element is treated as a beam on pinned supports. The beam will be provided with links to carry shear and to accommodate the requirements of Cl. 9.2.5 – indirect support of the ribbed slab described in Section 3.3.8. Arrangement: Choose to use all-and-alternate-spans-loaded.

‡

120

cf. 126.7 kN/m from analysis of slab (63.2 kN/m + 63.5 kN/m). See Figure 3.12.


-',3
4.3.4 Analysis Analysis by computer, assuming simple supports and including 15% redistribution at supports (with in this instance consequent redistribution in span moments).

EC0: A1.2.2 & NA; Cl. 5.3.1 (6) 5.3.1(6)


Table 4.3 Elastic and redistributed moments, kNm Span number

1

2

3

4

Elastic M

641.7

433.0

433.0

641.7

Redistributed M

606.4

393.2

393.2

606.4

d

0.945

0.908

0.908

0.945

800

657.4 kNm

600

657.4 kNm 516.0 kNm

400 200 0 – 200

A

B

– 400

C

– 393.2 kNm

– 600

D

E

– 393.2 kNm

– 606.4 kNm

– 606.4 kNm

– 800

Figure 4.18 Redistributed envelope, kNm 800 569.1 kN

600 400

517.9 kN 394.6 kN

462.6 kN

200 0 – 200

A

B

C

D

E

– 400 – 462.6 kN – 600

– 395.6 kN – 517.9 kN

– 569.1 kN

– 800

Figure 4.19 Redistributed shears, kN 121

4.3.5 Flexural design, span AB a) Span AB (and DE) – Flexure MEd = 606.4 kNm K = MEd/bd2fck


where b = beff = beff1 + bw + beff2 where beff1 = (0.2b1 + 0.1l0) ≤ 0.2l0 ≤ b1 where b1 = distance between webs/2 Referring to Figures 3.8 and 3.9 = (7500 – 1000 − 550)/2 = 2975 mm l0 = 0.85 × l1 = 0.85 × 7500 = 6375 mm beff1 = 0.2 × 2975 + 0.1 × 6375 ≤ 0.2 × 6375 ≤ 2975 = 1232 ≤ 1275 ≤ 2975 = 1232 mm bw = 2000 mm beff2 = (0.2b2 + 0.1l0) ≤ 0.2 l0 ≤ b2 where b2 = distance between webs/2. Referring to Figures 3.8 and 3.9 = (9000 – 1000 − 550)/2 = 3725 mm l0 = 6375 mm as before beff2 = 0.2 × 3725 + 0.1 × 6375 ≤ 0.2 × 6375 ≤ 3725 = 1382 ≤ 1275 ≤ 3725 = 1275 mm

Cl. 5.3.2.1, Fig. 5.3

Fig. 5.2

b = 1232 + 2000 + 1275 = 4507 mm d = 300 − 25 – 10 – 25/2 = 252 mm assuming 10 mm link and H25 in span. fck = 35 MPa K = 606.4 × 106/(4507 × 2522 × 35) = 0.061 K' = 0.207 or restricting x/d to 0.45 K' = 0.168 K ≤ K' = section under-reinforced and no compression reinforcement required. z = (d/2) [1 + (1 − 3.53K)0.5] ≤ 0.95d = (252/2) (1 + 0.886) ≤ 0.95 × 252 = 238 ≤ 239 = z =238 mm 122

Appendix A1

Appendix A1

-',3

But z = d – 0.4 x = x = 2.5(d – z) = 2.5( 252 − 236) = 32 mm = neutral axis in flange. Asx < 1.25hf design as rectangular section. As = MEd/fydz where fyd = 500/1.15 = 434.8 MPa = 606.4 × 106/(434.8 × 239) = 5835 mm2 Try 12 no. H25 B (5892 mm2) b) Span AB – Deflection Check span-to-effective-depth ratio. Allowable l/d = N × K × F1 × F2 × F3 where N = Basic l/d: check whether r > r0 and whether to use Exp. (7.16a) or (7.16b) r = = = = r0 = N = = = K = F1 =

As/Ac‡ = As,req/[bw d + (beff – bw)hf] 5835/[2000 × 252 + (4507 – 2000) × 100] 5835/754700 0.77% fck0.5/1000 = 300.5/1000 = 0.59% r > r0 = use Exp. (7.16b)

11 + 1.5fck0.5 r0/(r – r') + fck0.5(r'/r0)0.5/12 11 + 1.5 (350.5 × 0.059/(0.077 – 0) + 350.5(0/0.59)1.5 11 + 6.8 + 0 = 17.8 (end span) = 1.3 (beff/bw = 4057/2000 = 2.03) = 0.90

F2 = 7.0/leff (span > 7.0 m) where leff = 7100 + 2 × 300/2 = 7400 mm F2 = 7.0/7.4 = 0.95 F3 = 310/ss ≤1.5 where§ ss = (fyk/gS) (As,req/As,prov) (SLS loads/ULS loads) (1/d) = 434.8 × (5835/5892) [(47.8 + 0.3 × 45.8)/(1.25 × 47.8 + 1.5 × 45.8)] × (1/0.945) = 434.8 × 0.99 × 0.48 × 1.06 = 219 MPa

Appendix A1

Appendix B Appendix C7 Cl. 7.4.2(2), Exp. (7.16a), Exp. (7.16b) PD 6687[6]

Exp. (7.16b)

Table 7.4N & NA Cl. 7.4.2(2), Appendix C7 Cl. 7.4.2(2), 5.3.2.2(1)

Cl. 7.4.2, Exp. (7.17), Table 7.4N & NA, Table NA.5 Note 5

‡ 2.18 of PD 6687[6] suggests that r in T sections should be based on the area of concrete above the centroid of the tension steel. §

See Appendix B1.5 123

F3 = 310/ss = 310/219 = 1.41


= Permissible l/d = 17.8 × 1.3 × 0.90 × 0.95 × 1.41 = 27.9 Actual l/d = 7500/252 = 29.8 = no good Try 13 no. H25 B (6383 mm2) F3 = 310/ss = 310/219 × 13/12 = 1.53‡ = say 1.50 = Permissible l/d = 17.8 × 1.3 × 0.90 × 0.95 × 1.50 = 29.7 Say OK Actual leff /d = 7400/252 = 29.4 Use 13 no. H25 B (6383 mm2)

4.3.6 Flexural design, support B (and D) At centreline of support: M = 657.4 kNm At face of support: MEd = 657.4 – 0.2 × 517.9 + 0.202 × 128.5/2 = 657.4 – 101.0 = 556.4 kNm K = MEd/bwd2fck

Cl. 5.3.2.2(3)

where bw = 2000 mm d = 300 − 25 cover − 12 fabric − 8 link – 16 bar − 25/2 bar = 226 mm 25 cover 12 fabric 8 link 16 bar

20 bar 8 link 25 cover

16 bar 25 bar 8 link 25 cover

Figure 4.20 Section at rib-beam interface K = 556.4 × 106/(2000 × 2262 × 35) = 0.156 By inspection, K < K' K' = 0.167 maximum (or for d = 0.85, K' = 0.168) = No compression steel required.

Appendix A1 Table C.4

‡ Both

NA, Table NA.5

As,prov/As,req and any adjustment to N obtained from Exp. (7.16a) or Exp. (7.16b) is restricted to 1.5 by Note 5 to Table NA.5 in the UK NA.

124

-',3
z = (226/2)[1 + (1 − 3.53 K' )0.5] = (226/2)[1 + (1 − 3.53 × 0.156)0.5] = (226/2) (1 + 0.67) < 0.95d = 189 mm


As = MEd/fydz = 556.4 × 106/(434.8 × 189) = 6770 mm2 Try 14 no. H25 T (6874 mm2) To be spread over beff beff = beff1 + bw + beff2 where beff1 = (0.2b1 + 0.1l0) ≤ 0.2l0 ≤ b1 where b1 referring to Figure 3.9 = (7500 – 1000 – 550)/2 = 2975 mm l0 = 0.15 × (l1 + l2) = 0.15 × (7500 + 7500) = 2250 mm beff1 = 0.2 × 2975 + 0.1 × 2250 ≤ 0.2 × 2250 ≤ 2975 = 820 ≤ 450 ≤ 2975 = 450 mm bw = 2000 mm beff2 = 450 mm as before = beff = 450 + 2000 + 450 = 2900 mm

Cl. 9.2.1.2(2), Fig. 9.1 Cl. 5.3.2.1, Fig. 5.3

Fig. 5.2

Check cracking: Spacing = 2900 – 2 × (25 – 10 – 25/2)/(14 − 1) = 216 mm ss = (fyk/gS) (As,req/As,prov) (SLS loads/ULS loads) (1/d) = 434.8 × (6770/6874) [ (47.8 + 0.3 × 45.8)/ (1.25 × 47.8 + 1.5 × 45.8) × (1/0.85) = 434.8 × 0.98 × 0.48 × 1.18 = 241 MPa

Cl. 7.3.3

As loading is the cause of cracking satisfy either Table 7.2N or Table 7.3N

Cl. 7.3.3(2) & Note

For wk = 0.4 and ss = 240 MPa max. spacing = 250 mm

= OK

Table 7.3N

4.3.7 Flexural design, span BC (and CD similar) a) Flexure MEd = 393.2 kNm K = MEd/bd2fck where b = beff = beff1 + bw + beff2 where beff1 = (0.2b1 + 0.1l0) ≤ 0.2l0 ≤ b1

Cl. 5.3.2.1, Fig. 5.3

125


where b1 referring to Figure 3.9 = (7500 – 1000 – 550)/2 = 2975 mm l0 = 0.70 × l2 = 0.7 × 7500 = 5250 mm beff1 = 0.2 × 2975 + 0.1 × 5250 ≤ 0.2 × 5250 ≤ 2975 = 1120 ≤ 1050 ≤ 2975 = 1050 mm bw = 2000 mm beff2 = (0.2b2 + 0.1l0) ≤ 0.2l0 ≤ b2

Fig. 5.2

where b2 = distance between webs/2 Referring to Figures 3.8 and 3.9 = (9000 – 1000 – 550)/2 = 3725 mm l0 = 5250 mm as before beff2 = 0.2 × 3725 + 0.1 × 5250 ≤ 0.2 × 5250 ≤ 3725 = 1270 ≤ 1050 ≤ 3725 = 1270 mm b = 1050 + 2000 + 1270 = 4320 mm d = 252 mm as before assuming 10 mm link and H25 in span fck = 30 K = 393.2 × 106/(4320 × 2522 × 35) = 0.041 By inspection, K ≤ K' = section under-reinforced and no compression reinforcement required.

Appendix A1

z = (d/2) [1 + (1 – 3.53K)0.5] ≤ 0.95d = (252/2) (1 + 0.924) ≤ 0.95 × 252 = 242 > 239 = z = 239 mm By inspection, x < 1.25 hf = design as rectangular section

Appendix A1

As = MEd/fydz = 393.2 × 106/(434.8 × 239) = 3783 mm2 Try 8 no. H25 B (3928 mm2) b) Deflection By inspection, compared to span AB OK But for the purposes of illustration: Check span-to-effective-depth ratio. Allowable l/d = N × K × F1 × F2 × F3 where N = Basic l/d: check whether to use Exp. (7.16a) or (7.16b)

126

Appendix A1

Appendix B Appendix C7 Cl. 7.4.2(2)

-',3
r0 = 0.59% (for fck = 35) r = As/Ac‡ = As,req /[bwd + (beff – bw)hf]


where bw = 2000 mm r = 3783/(2000 × 252 + (4320 – 2000) × 100) = 3783/736000 = 0.51% r < r0 = use Exp. (7.16a) N = = = = K = F1 =

11 + 1.5fck0.5 r0 /r + 3.2fck0.5(r0 /r – 1)1.5 11 + 1.5 × 350.5 × 0.059/0.051 + 3.2 × 350.5(0.059/0.051 – 1)1.5 11 + 10.2 + 23.5 = 17.8 44.7 (internal span) = 1.5 (beff/bw = 4320/2000 = 2.16) = 0.88

F2 = 7.0/leff = 7.0/7.4 = (span > 7.0 m) = 0.95 F3 = 310/ss ≤1.5

Exp. (7.16a)

Table 7.4N & NA Cl. 7.4.2(2), Appendix C7 Cl. 7.4.2(2) Cl. 7.4.2, Exp. (7.17) Table 7.4N, & NA, Table NA.5 Note 5

where§ ss = (fyk/gS) (As,req/As,prov) (SLS loads/ULS loads) (1/d) = 434.8 × (3783/3828) [(47.8 + 0.3 × 45.8)/(1.25 × 47.8 + 1.5 × 45.8)] × (1/0.908) = 434.8 × 0.99 × 0.48 × 1.10 = 227 MPa F3 = 310/ ss = 310/227 = 1.37 = Permissible l/d = 44.7 × 1.37 × 0.88 × 0.95 × 1.37 = 70.1 Actual l/d = 7500/252 = 29.8 = OK Use 8 no. H25 B (3928 mm2)# c) Hogging Assuming curtailment of top reinforcement at 0.30l + al, From analysis MEd at 0.3l from BC (& DC) = 216.9 kNm at 0.3l from CB (& CD) = 185.6 kNm K = 216.9 × 106/(2000 × 2262 × 35) = 0.061 By inspection, K < K'

How to: Detailing

‡ 2.18 of PD 6687[6] suggests that r in T sections should be based on the area of concrete above the centroid of the tension steel. §See #

Appendix B1.5

12 no. H20 B (3768 mm2) used to suit final arrangement of links. 127

(226/2)[1 + (1 − 3.53 K')0.5] (226/2)[1 + (1 − 3.53 × 0.061)0.5] (226/2) (1 + 0.89) < 0.95d 214 mm < 215 mm MEd/fydz 216.9 × 106/(434.8 × 214) = 2948 mm2 Use 12 no. H20 T (3748 mm2) (to suit links and bottom steel) Top steel at supports may be curtailed down to 12 no. H20 T at 0.3l + al = 0.3 × 7500 + 1.25 × 214 = 2518 say 2600 mm from centreline of support.


z = = = = As = =

Cl. 9.2.1.3(2)

4.3.8 Flexural design, support C At centreline of support, M = 516.0 kNm At face of support, MEd = 516.0 – 0.2 × 462.6 + 0.202 × 128.5/2 = 516.0 – 90.0 = 426.0 kNm K = MEd/bwd2fck

Cl. 5.3.2.2(3)

where bw = 2000 mm d = 226 mm as before K = 426.0 × 106/(2000 × 2262 × 35) = 0.119 By inspection, K < K' z

= (226/2) [1 + (1 − 3.53K)0.5] = (226/2) [1 + (1 − 3.53 × 0.119)0.5] = (226/2) (1 + 0.76) < 0.95d = 199 mm

As = MEd/fydz = 426.0 × 106/(434.8 × 199) = 4923 mm2 Try 10 no. H25 T (4910 mm2)‡

4.3.9 Design for beam shear a) Support A (and E) At d from face of support, VEd = 394.6 − (0.400/2 + 0·252) × 128.5 = 336.5 kN Maximum shear resistance: By inspection, VRd,max OK and cot y = 2.5 ‡

128

12 no. H25 used to suit final arrangement of links.

Cl. 6.2.1(8)

-',3
However, for the purpose of illustration: check shear capacity, VRd,max = acw bw zvfcd/ (cot y + tan y)


where acw = bw = z = v = fcd = y =

Exp. (6.9) & NA 1.0 2000 mm as before 0.9d 0.6 [1 − fck/250] = 0.516 35/1.5 = 23.3 MPa angle of inclination of strut. By inspection, cot−1 y << 21.8. But cot y restricted to 2.5 and = tan y = 0.4.

VRd,max = 1.0 × 2000 × 0.90 × 252 × 0.516 × 23.3/(2.5 + 0·4) = 2089.5 kN = OK Shear links: shear resistance with links ORd,s = (Asw/s) z fywd cot y ≥ VEd = for VEd ≤ VRd,s Asw /s ≥ VEd/z fywd cot y where Asw /s z fywd cot y

= = = =

Cl. 6.2.3(1)

Cl. 6.2.3(2) & NA

Exp. (6.8)

area of legs of links/link spacing 0.9d as before 500/1.15 = 434.8 2.5 as before

Asw /s ≥ 336.5 × 103/(0.9 × 252 × 434.8 × 2.5) = 1.36 Minimum Asw /s = rw,minbwsin a

Cl. 9.2.2(5), Exp. (9.4)

where rw,min = 0.08 × fck0.5/fyk = 0.08 × 350.5/500 = 0.00095

Exp. (9.5N) & NA

= 2000 mm as before = angle between shear reinforcement and the longitudinal axis. For vertical reinforcement sin a = 1.0 Minimum Asw /s = 0.00095 × 2000 × 1 = 1.90 But, maximum spacing of links longitudinally = 0.75d = 183 mm Maximum spacing of links laterally = 0.75d ≤ 600 mm = 183 mm H10s required to maintain 35 mm cover to H25 = Use H10 @ 175 cc both ways i.e. H10 in 12§ legs @ 175 mm cc (Asw /s = 5.38) bw a

Cl. 9.2.2(6) Cl. 9.2.2(8)

§ (2000 mm – 2 × 25 mm cover − 10 mm diameter)/175 = 11 spaces, = 12 legs.

129


b) Support B (and C and D) By inspection, the requirement for minimum reinforcement and, in this instance, for H10 legs of links will outweigh design requirements. Nonetheless check capacity of Asw/s = 5.38 VRd,s = (Asw/s) z fywd cot y = 5.38 × 0.9 × 252 × 434.8 × 2.5 = 1326.3 kN Maximum shear at support = 517.9 kN i.e. capacity of minimum links not exceeded. By inspection, the requirement for indirect support of the ribs of the slab using 87 mm2/rib within 150 mm of centreline of ribs (at 900 mm centres) and within 50 mm of rib/solid interface is adequately catered for and will not unduly effect the shear capacity of the beam. Use 150 mm centres to tie in with 900 mm centres of ribs

Exp. (6.8)

Cl. 9.2.5, Section 3.4.8

= Use H10 in 12 legs @ 150 mm cc (Asw/s = 6.28) throughout beam

4.3.10 Check for punching shear, column B As the beam is wide and shallow it should be checked for punching shear. At B, applied shear force, VEd = 569.1 + 517.9 = 1087.0 kN. Check at perimeter of 400 × 400 mm column: vEd = b VEd/uid < vRd,max where b = factor dealing with eccentricity; recommended value 1.15 VEd = applied shear force ui = control perimeter under consideration. For punching shear adjacent to interior columns u0 = 2(cx + cy) = 1600 mm d = mean d = (245 + 226)/2 = 235 mm = 1.15 × 1087.0 × 103/1600 × 235 = 3.32 MPa vEd vRd,max = 0.5vfcd where v = 0.6(1 − fck/250) = 0.516 fcd = acclfck/gC = 1.0 × 1.0 × 35/1.5 = 23.3 vRd,max = 0.5 × 0.516 × 23.3 = 6.02 MPa = OK Check shear stress at basic perimeter u1 (2.0d from face of column): vEd = bVEd /u1d < vRd,c where b, VEd and d as before

‡ In this case, at the perimeter of the column, it is assumed that the strut angle is 45°, i.e. that cot y = 1.0. In other cases, where cot y < 1.0, vRd,max is available from Table C7. 130

Cl. 6.4.3(2), 6.4.5(3)

Fig. 6.21N & NA Cl. 6.4.5(3) Exp. (6.32) Cl. 6.4.5(3) Note Exp. (6.6) & NA Table C7‡ Cl. 6.4.2

Fig. 6.13

-',3

u1 = control perimeter under consideration. For punching shear at 2d from interior columns = 2(cx + cy) + 2π × 2d = 1600 + 2π × 2 × 235 = 4553 mm vEd = 1.15 × 1087.0 × 103/4553 × 235 = 1.17 MPa vRd,c = 0.18/ gC × k × (100 rlfck)0.333 where gC = 1.5 k = 1 + (200/d)0.5 ≤ 2 = 1 +(200/235)0.5 = 1.92 rl = (rly, rlz)0.5 where rly, rlz = Reinforcement ratio of bonded steel in the y and z direction in a width of the column plus 3d each side of column. = 6874/(2000 × 226) = 0.0152 = 741/(900 × 245) = 0.0036 rlz rl = (0.0152 × 0.0036)0.5 = 0.0074 fck = 35 vRd,c = 0.18/1.5 × 1.92 × (100 × 0.0074 × 35)0.333 = 0.68 MPa§ = punching shear reinforcement required Shear reinforcement (assuming rectangular arrangement of links): At the basic control perimeter, u1, 2d from the column: Asw ≥ (vEd – 0.75vRd,c) sr u1 /1.5fywd,ef) where sr = 175 mm fywd,ef = effective design strength of reinforcement = (250 + 0.25d) < fyd = 309 MPa

Exp. (6.47) & NA

Cl. 6.4.4.1(1)

Table C6#

Exp. (6.52) Cl. 9.4.3(1) Cl. 6.4.5(1)

For perimeter u1 Asw = (1.17 – 0.75 × 0.68) × 175 × 4553/(1.5 × 309) = 1135 mm2 per perimeter Try 15 no. H10 (1177 mm2)

§ See Section 3.4.14 with respect to possible limit of 2.0 or 2.5 on V /V Ed Rd,c within punching shear requirements. #

vRd,c for various values of d and rl is available from Table C6. 131

Check availability of reinforcement‡: 1st perimeter to be > 0.3d but < 0.5d, i.e between 70 mm and 117 mm from face of column. Say 0.4d = 100 mm from face of column. By inspection of Figure 4.21. the equivalent of 14 locations are available between 70 mm and 117 mm from face of column therefore say OK. CL 200 200

470

150 150 150 150 150 150

H10 legs of links

CL

175 175 175 175 175 175


900 470

s = 150 mm u1

600 70

24 H10 legs in u1 perimeter 58

Figure 4.21 Shear links and punching shear perimeter u1 Perimeter at which no punching shear links are required: uout = VEd × b/(d × vRd,c) uout = 1087 × 1.15 × 103/(235 × 0.68) = 7826 mm Length of column faces = 4 × 400 = 1600 mm Radius to uout = (7823 – 1600)/2π = 990 mm from face of column i.e. in ribs, therefore beam shear governs

‡ The same area of shear reinforcement is required for all perimeters inside or outside perimeter u1. See Section 3.4.13.

Punching shear reinforcement is also subject to requirements for minimum reinforcement and spacing of shear reinforcement (see Cl. 9.4.3). The centre of links from the centreline of the column shown in Figure 4.21 have been adjusted to accommodate a perimeter of links at between 0.3d and 0.5d from the column face. 132

Fig. 9.10, 9.4.3(4)

-',3
4.3.11 Summary of design X H10 links in 12 legs @ 150 cc


A

12H20T 14H25T

B 13H25B

12H20T 12H25T

C 12H20B

14H25T

D 12H20B

E 13H25B

X

Figure 4.23 Section X–X

133

. Columns .') General Ma^\Ze\neZmbhglbgmabll^\mbhgbeenlmkZm^3 .'*=^lb`gh_Zghg&le^g]^k^]`^\henfgnlbgàZg]\Ze\neZmbhg' .'+=^lb`gh_Zi^kbf^m^k\henfgnlbg`bm^kZmbhgh_^jnZmbhglmh]^m^kfbg^k^bg_hk\^f^gm k^jnbk^f^gml' .',=^lb`gh_Zgbgm^kgZe\henfgpbmaabàZqbZeehZ]'


.'-=^lb`gh_Zle^g]^k\henfgk^jnbkbg`Zmph&ahnkËk^k^lblmZg\^' Bg`^g^kZe%ZqbZeehZ]lZg]Ëklmhk]^kfhf^gmlZk^Zllnf^]mh[^ZoZbeZ[e^'Ma^]^lb`gl\hglb]^k le^g]^kg^llbghk]^kmh]^m^kfbg^]^lb`gfhf^gml%F>]'Ma^\henfglZk^]^lb`g^]Zg]\a^\d^] _hk[bZqbZe[^g]bg`'Ma^^__^\mlh_Zeehpbg`_hkbfi^k_^\mbhglZk^beenlmkZm^]' :`^g^kZef^mah]h_]^lb`gbg`\henfglblZl_heehpl'BgikZ\mb\^%lô^kZeh_ma^l^lmîlfZr[^ \hf[bg^]' N =^m^kfbg^]^lb`geb_^'

EC0 & NA Table NA 2.1

N :ll^llZ\mbhglhgma^\henfg'

EC1 (10 parts) & UK NAs

N =^m^kfbg^pab\a\hf[bgZmbhglh_Z\mbhglZiier'

EC0 & NA Tables NA A1.1 & NA A1.2(B)


BS 8500–1

lmk^g`ma' N
k^lblmZg\î^kbh]'

Approved Document B, EC2–1–2

N =^m^kfbg^\ho^k_hk_bk^%]nkZ[bebmrZg][hg]'

Cl. 4.4.1

N :gZerl^lmkn\mnk^_hk\kbmb\Ze\hf[bgZmbhgfhf^gml

Section 5

Zg]ZqbZe_hk\^l'

134

N
Section 5.8

N =^m^kfbg^Zk^Zh_k^bg_hk\^f^gmk^jnbk^]'

Section 6.1

N
Sections 8 & 9


Ma^bgm^gmbhgh_mabl\Ze\neZmbhgblmhlahpZmrib\ZeaZg]\Ze\neZmbhgmaZmfZd^lk^_^k^g\^ mh]^lb`g\aZkml' Ikhc^\m]^mZbel

chg

Ch[gh'

Edge column

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

A 300 mm square column on the edge of a flat slab structure supports an axial load of 1620 kN and first order moments of 38.5 kNm top and −38.5 kNm bottom in one direction only‡. The concrete is grade C30/37, fck = 30 MPa and cover, cnom, = 25 mm. The 250 mm thick flat slabs are at 4000 mm vertical centres.

38.5 kNm NEd = 1620 kN

– 38.5 kNm

Figure 5.1 Forces in edge column

5.1.1 Check slenderness, l Effective length§, l0 = factor × l where factor = from Table C16, condition 2 each end = 0.85 l = clear height = 3750 mm = l0 = 0.85 × 3750 = 3187 mm Slenderness l = l0/i

Cl. 5.8.3.2 Table C16, PD 6687: 2.10

Exp. (5.14)

‡

For examples of load take-downs and 1st order moment analysis see Section 5.3.2 § Effective lengths are covered in Eurocode 2 Cl. 5.8.3.2 and Exp. (5.15). The effective length of most columns will be l /2< l0 < l (see Eurocode 2 Figure 5.7f). PD 6687[6] Cl. 2.10 suggests that using the procedure outlined in Eurocode 2 (5.8.3.2(3) and 5.8.3.2(5)) leads to similar effective lengths to those tabulated in BS 8110[7] and reproduced in Table 5.1 of Concise Eurocode 2[5] and in this publication as Table C16. For simplicity, tabular values are used in this example. However, experience suggests that these tabulated values are conservative.

Fig. 5.7 PD 6687[6]: Cl. 2.10 Cl. 5.8.3.2(3) 5.8.3.2(5) Table C16 135

where i = radius of gyration = h/120.5 for rectangular sections l = 3187 × 3.46/300

= 36.8


5.1.2 Limiting slenderness, llim

llim = 20 ABC/n0.5 where A = 0.7 (default) B = 1.1 (default) C = 1.7 − rm = 1.7 − M01/M02 = 1.7 − 38.5/(−38.5) = 2.7 n = NEd/Acfcd = 1620 × 103/(3002 × 0.85 × 30/1.5) = 1.06 0.5 llim = 20 ABC/n = 20 × 0.7 × 1.1 × 2.7/1.060.5 In this example llim = 40.4 i.e. > 36.8 = Column not slender

Exp. (5.13N) Cl. 5.8.3.1(1)

5.1.3 Design moments MEd = max[M02; M0Ed + M2; M01 + 0.5M2] where M02 = where M ei e0 M02 = = = M0Ed = = = = M2 = M01 =

Cl. 5.8.8.2(1)

M + eiNEd ≥ e0NEd

Cl. 5.8.8.2, 6.1.4

= 38.5 kNm = l0/400 = max[h/30; 20] = max[300/30; 20] = 20 mm 38.5 + 1620 × 3.187/400 ≥ 0.02 × 1620 38.5 + 12.9 ≥ 32.4 kNm 51.4 kNm 0.6M02 + 0.4M01 ≥ 0.4M02 0.6 × 51.4 + 0.4 × (−38.5 + 12.9) ≥ 0.4 × 51.4 20.6 ≥ 20.6 20.6 0 (column is not slender) M02

= max[M02 ; M0Ed + M2 ; M01 + 0.5M2] = 51.4 kNm

Cl. 5.2.7, 5.2.9 Cl. 6.1.4

= MEd = 51.4 kNm

5.1.4 Design using charts (see Appendix C) d2 = cnom + link + f/2 = 25 + 8 + 16 = 49 d2/h = 49/300 = 0.163 = interpolating between d2/h = 0.15 and 0.20 for NEd/bhfck = 1620 × 103/(3002 × 30) = 0.60 136

Figs. C5c), C5d)

.'*3>]`^\henfg

MEd/bh2fck = 51.4 × 106/(3003 × 30) = 0.063 Asfyk/bhfck = 0.24 As = 0.24 × 3002 × 30/500 = 1296 mm2 Try 4 no. H25 (1964 mm2)


5.1.5 Check for biaxial bending ly /lz ≈ 1.0 i.e. ly /lz ≤ 2.0 = OK but check Exp. (5.38b)

Cl. 5.8.9 Exp. (5.38a)

As a worst case MEdy may coexist with e0NEd about the orthogonal axis:

Cl. 6.1(4)

ey/heq ez/beq

=

(MEdz/NEd)/h (MEdy/NEd)/b

=

MEdz MEdy

Exp. (5.38b)

Imperfections need to be taken into account in one direction only. = As a worst case for biaxial bending

Cl. 5.8.9(2)

MEdz = M + 0 = 38.5 kNm MEdy = e0NEd = 32.4 kNm 38.5 MEdz = = 1.19 i.e. > 0.2 and < 5.0 32.4 MEdy

Exp. (5.38b) = Biaxial check required

Cl. 5.8.9(4)

Check whether (MEdz/MRdz)a + (MEdy/MRdy)a ≤ 1.0

Exp. (5.39)

where MEdz = 38.5 kNm MEdy = 32.4 kNm MRdz = MRdy

Figs. C5c), C5d)

To determine MRdz, find MEd/bh2fck (and therefore moment capacity) by interpolating between d2/h = 0.15 (Figure C5c) and 0.20 (Figure C5d) for the proposed arrangement and co-existent axial load. Assuming 4 no. H25, Asfyk/bhfck = 1964 × 500/(3002× 30) = 0.36 Interpolating for NEd/bhfck = 0.6, MEd/bh2fck = 0.094 = MRdz = MRdy = 0.094 × 3003 × 30 = 76.1 kNm a is dependent on NEd/NRd where NEd = 1620 kN as before

Cl. 5.8.9(4), Notes to Exp. (5.39)

137

NRd

= Acfcd + Asfyd = 3002 × 0.85 × 30/1.5 + 1964 × 500/1.15 = 1530.0 + 853.9 = 2383.9 kN NEd/NRd = 1620/2383.9 = 0.68 =a = 1.48 by interpolating between values given for NEd/NRd = 0.1, (1.0) and NEd/NRd = 0.7, (1.5)


(MEdz/MRdz)a + (MEdy/MRdy)a

= (38.5/76.1)1.48 + (32.4/76.1)1.48 = 0.36 + 0.28 = 0.64 = OK. = 4 no. H25 OK

Exp. (5.39)

5.1.6 Links Diameter min. f/4 = 25/4 = 8 mm Max. spacing = 0.6 × 300 = 180 mm

Cl. 9.5.3 & NA Cl. 9.5.3(3), Cl. 9.5.3(4) Links at say 175 mm cc

5.1.7 Design summary 4 H25 H8 links @ 175 cc 25 mm cover fck = 30 MPa

Figure 5.2 Design summary: edge column

138

.'+3I^kbf^m^k\henfg .'+ Perimeter column (internal environment) Mabl^qZfie^blbgm^g]^]mhlahpZaZg]\Ze\neZmbhg_hkZghg&le^g]^ki^kbf^m^k\henfg nlbg`bm^kZmbhg!h_q"mh]^m^kfbg^ma^k^bg_hk\^f^gmk^jnbk^]' Ikhc^\m]^mZbel


Perimeter column (internal environment)

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

This 300 × 300 mm perimeter column is in an internal environment and supports three suspended floors and the roof of an office block. It is to be designed at ground floor level where the storey height is 3.45 m and the clear height in the N–S direction (z direction) is 3.0 m and 3.325 m in the E–W direction (y direction). One-hour fire resistance is required and fck = 30 MPa.

M02yy 3575

250 325 300 × 300 Column under consideration

Figure 5.3 Perimeter column (internal environment) From first order analysis, load case 1: NEd = 1129.6 kN; M02yy = 89.6 kNm; M02zz = 0 Load case 2: NEd = 1072.1 kN; M02yy = 68.7 kNm; M02zz = 6.0 kNm

5.2.1 Cover cnom = cmin + Dcdev where cmin = max[cmin,b; cmin,dur] where cmin,b = diameter of bar. Assume 32 mm bars and 8 mm links = 32 mm to main bars, 32 − 8 = 24 mm to links = say 25 mm cmin,dur = minimum cover due to environmental conditions. Assume XC1. cmin,dur = 15 mm cmin = 25 mm Dcdev = 10 mm Therefore cnom = 25 + 10 = 35 mm to links

Exp. (4.1)

Cl. 4.4.1.2(3)

Cl. 4.4.1.3(3) cnom = 35 mm to links. 139

5.2.2 Fire resistance Check validity of using Method A and Table 5.2a of BS EN 1992–1–2: l0,fi ≈ 0.7 × 3.325 i.e. < 3.0 m = OK. e

= M02yy /NEd = 89.6 × 106/1129.6 × 103 = 79 mm

EC2-1-2: 5.3.2, Table 5.2a EC2-1-2: 5.3.3(3) EC2-1-2: 5.3.2 & NA


emax = 0.15h = 0.15 × 300 = 45 mm = no good. Check validity of using Method B and Table 5.2b: emax = 0.25b = 75 mm = no good.

EC2-1-2: 5.3.3

Use BS EN 1992–1–2 Annex C Tables C1–C9.

EC2-1-2: Annex C EC2-1-2: 5.3.3(2)

Assume min. 4 no. H25 = 1964 mm2 (z 2.2%)‡ w = Asfyd/Acfcd = 0.022 × (500/1.15)/(0.85 × 30/1.5) = 0.56 e ≈ 0.25b and ≤ 100 mm l = l0 /i where l0 = 0.7 × 3.325 = 2327 mm i = radius of gyration = (I/A)0.5 = h/120.5 where I = inertia = bh3/12 A = area = bh h = height of section b = breadth of section = 300/120.5 = 87 mm l = 2327/87 = 276 n = N0Ed,fi/0.7(Acfcd + Asfyd)

EC2-1-2: 5.3.3(2), 5.3.3(3)

EC2-1-2: 5.3.3(2)

1129.6/0.7(3002

× 0.85 × 30/1.5 + 1964 × 500/1.15) = 0.7 × = 1129.6/2383.9 = 0.47 = interpolate for l = 30 and n = 0.47 between from Table C.5 of BS EN 1992–1–2 (w = 0.5, e = 0.25b): minimum dimension, bmin = 235, and axis distance, a = 35 mm and from Table C.8 of BS EN 1992–1–2 (w = 1.0, e = 0.25b):

‡ Using 4 no. H20 gives w = 0.34, n = 0.54 and bmin = 310 mm = no good. 140

EC2-1-2: Table C.5 EC2-1-2: Table C.8

.'+3I^kbf^m^k\henfg

bmin = 185, and a = 30 mm = for w = 0.56, bmin = 228, and a = 35 mm OK to use Method B but use min. 4 no. H25


5.2.3 Structural design: check slenderness Effective length, l0: l0 = 0.5l [1 + k1 /(0.45 + k1) ]0.5 [1 + k2/(0.45 + k2) ]0.5 where k1, k2 = relative stiffnesses top and bottom

Exp. (5.15)

But conservatively, choose to use tabular method§. For critical direction, the column is in condition 2 at top and condition 3 at bottom (pinned support). l0 = 0.95 × 3325 = 3158 mm

Table C16

Slenderness ratio, l: l = l0/i where i = radius of gyration = (I/A)0.5 = h/120.5 l = 3158 × 120.5/300 = 36.5

Cl. 5.8.3.2(1)

Limiting slenderness ratio, llim llim = 20 ABC/n0.5 where A = 1/(1 + 0.2 fef). Assume 0.7 B = (1 + 2 Asfyd/Acfcd)0.5 = (1 + 2w)0.5 Assuming min. 4 no. H25 (for fire) w = 0.56 as before B = (1 + 2 × 0.56)0.5 = 1.46 C = 1.7 – rm where rm = M01/M2 Assuming conservatively that M01 = 0 rm = 0 C = 1.7 n = NEd/Acfcd = 1129.6 × 103/(3002 × 0.85 × 30/1.5) = 0.74

§

l = 36.5 Cl. 5.8.3.1(1) & NA Cl. 5.8.4 Cl. 5.8.3.1(1)

Cl. 5.8.3.1(1)

See footnote to Section 5.1.1. 141

llim = 20 × 0.7 × 1.46 × 1.7/0.740.5 = 40.4 llim = 40.4 = as l < llim column is not slender and 2nd order moments are not required. Column is not slender

5.2.4 Design moments, MEd


MEd = MOEd + M2 ≥ e0NEd

But as column is not slender, M2 = 0, = MEd = MOed = M + eiNEd ≥ e0NEd

Cl. 5.8.8.2(1), 5.8.8.2(3) Cl. 6.1.4

where M = moment from 1st order analysis eiNEd = effect of imperfections‡ where ei = l0 /400 e0 = h/30 > 20 mm

Cl. 5.2(7), 5.2.9, 5.8.8.2(1) Cl. 6.1.4

Load case 1: MEdy = 89.6 + (3158/400) × 1129.6 × 10−3 > 0.02 × 1129.6 = 89.6 + 8.9 > 22.6 = 98.5 kNm Load case 2: MEdy = 68.7 kNm MEdz = 6.0 + (l0/400) × 1072.1 × 10−3 > 0.02 × 1072.1 where l0 = 0.9 × 3000 = 13.2 > 21.4 = 21.4 kNm

Table C16

5.2.5 Design using iteration of x For axial load: AsN/2 = (NEd – accnfckbdc /gC)/(ssc – sst)

142

Concise: Section 6.2.2, Appendix A3

For moment: [MEd – accnfckbdc (h/2 – dc/2)/ gC] AsM/2 = (h/2 – d2) (ssc – sst) where MEd = 98.5 × 106 NEd = 1129.6 × 103 acc = 0.85 n = 1.0 for fck ≤ 50 MPa

Cl. 3.1.6(1) & NA Exp. (3.21)

‡The effects of imperfections need only be taken into account in the most unfavourable direction.

Cl. 5.8.9(2)

Appendices A3, C9.2,

.'+3I^kbf^m^k\henfg


fck b h dc

= 30 = 300 = 300 = depth of compression zone = lx = 0.8x < h where x = depth to neutral axis d2 = 35 + 8 + 25/2 = 55 mm assuming H25 = 1.5 gC ssc, (sst) = stress in reinforcement in compression (tension) o

fcd = accnfck/gC o

ecu2

Table 2.1N

d2 ssc

As2

esc

Exp. (3.19)

dc

x h

n. axis ey o a) Strain diagram

As1

sst

d2 o

b) Stress diagram

Figure 5.4 Section in axial compression and bending

Fig. 6.1

Try x = 200 mm = ecu2 = 0.0035 ecu 0.0035 × (x – d2) 0.0035 × (200 – 55) esc = = x 200 = 0.0025 ssc = 0.0025 × 200000 ≤ fyk/gS = 500 ≤ 500/1.15 = 434.8 MPa = 0.0035(h – x – d2)/x = 0.0035(300 – 200 – 55)/200 est = 0.0008 sst = 0.0008 × 200000 ≤ 500/1.15 = 160 MPa 1129.6 × 103 – 0.85 × 1.0 × 30 × 300 × 200 × 0.8/(1.5 × 103) AsN/2 = 434.8 – 160 = (1129.6 – 816.0) × 103 = 1141 mm2 274.8 143

98.5 × 106 – 0.85 × 1.0 × 30 × 300 × 200 × 0.8 (300/2 – 200 × 0.8/2)/(1.5 × 103) (300/2 – 55) (434.8 + 160) 6 (98.5 – 57.1) × 10 = = 733 mm2 95 × 594.8

AsM/2 =


Similarly for x = 210 mm ecu = 0.0035 esc = 0.0026 = ssc = 434.8 est = 0.0006 = sst = 120 MPa AsN/2 =

(1129.6 – 856.8) × 103 = 866 mm2 434.8 – 120

AsM/2 =

(98.5 – 56.5) × 106 = 796 mm2 95 × 554.8

Similarly for x = 212 mm ssc = 434.8 = 0.00054 =est = 109 MPa est AsN/2 =

(1129.6 – 865.0) × 103 = 812 mm2 434.8 – 109

AsM/2 =

(98.5 – 56.3) × 106 = 816 mm2 95 × 543.8

= as AsN/2 ≈ AsM/2, x = 212 mm is approximately correct and AsN ≈ AsM, ≈ 1628 mm2 = Try 4 no. H25 (1964 mm2)

5.2.6 Check for biaxial bending By inspection, not critical. [Proof: Section is symmetrical and MRdz > 98.5 kNm. Assuming ey/ez > 0.2 and biaxial bending is critical, and assuming exponent a = 1 as a worst case for load case 2: (MEdz/MRdz)a + (MEdy/MRdy)a = (21.4/98.5)1 + (68.7/98.5)1 = 0.91 i.e. < 1.0 = OK.]

Cl. 5.8.9(3)

Exp. (5.39)

5.2.7 Links Minimum size links = 25/4 = 6.25, say 8 mm Spacing: minimum of a) 0.6 × 20 × 25 = 300 mm, b) 0.6 × 300 = 180 mm or c) 0.6 × 400 = 240 mm

Cl. 9.5.3(3), 9.5.3(4) Use H8 @ 175 mm cc

144

.'+3I^kbf^m^k\henfg

5.2.8 Design summary 4 H25 H8 links @ 175 cc cnom = 35 mm to links


Figure 5.5 Design summary: perimeter column

145

.', Internal column


Ma^ÌZmleZ[lahpgbg>qZfie^,'-!kîkh]n\^]Zl?b`nk^.'/"bliZkmh_Zg1&lmhk^rlmkn\mnk^ Z[ho^`khng]pbmaZ[Zl^f^gm[êhp`khng]'Maîkh[e^fblmh]^lb`g\henfg<+[^mp^^g `khng]ÌhhkZg]*lmÌhhk'

Ikhc^\m]^mZbel

chg

Ch[gh'

Internal column

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

The design forces need to be determined. This will include the judgement of whether to use Exp. (6.10) or the worse case of Exp. (6.10a) and (6.10b) for the design of this column. The suspended slabs (including the ground floor slab) are 300 mm thick flat slabs at 4500 mm vertical centres. Between ground and 5th floors the columns at C2 are 500 mm square; above 5th floor they are 465 mm circular. Assume an internal environment, 1-hour fire resistance and fck = 50 MPa. A

4.0

B

4.0

Bb

4.0

C

6.0

1

D E

200 x 200 hole 8.0

2

8.0

3

9.6 300 mm flat slabs All columns 400 mm sq.

200 x 200 hole

8.6

Figure 5.6 Part plan of flat slab

5.3.1 Design forces In order to determine design forces for this column it is first necessary to determine vertical loads and 1st order moments.

5.3.2 Load take-down Actions: Roof: gk = 8.5, qk = 0.6

146

EC1-1-1: 6.3.4, NA & Table NA.7

.',3Bgm^kgZe\henfg


Floors: gk = 8.5, qk = 4.0

Section 3.4

In keeping with Section 3.4 use coefficients to determine loads in take-down.

Section 3.4

Consider spans adjacent to column C2: Along grid C, consider spans to be 9.6 m and 8.6 m and C2 to be the internal of 2 - span element. Therefore elastic reaction factor = 0.63 + 0.63 = 1.26 Along grid 2 consider spans to be 6.0 m and 6.2 m and internal of multiple span. Elastic reaction factor = 0.5 + 0.5 = 1.00

Table C3

Load take-down for column C2. Item

Calculation

Gk From item

= [erfy × (lz1 + lz2)/2 ] × [erfz × (l y1 + ly2)/2 ] × (gk + qk) = [1.0 × (6.0 + 6.2)/2 ] × [1.26 × (9.6 + 8.6)/2 ] × (8.5 + 0.6) = 69.9 × (8.5 + 0.6) = Col 8 – R = π (0.465/2)2 × (4.5 − 0.3) × 25 = 8th = 1.0 × (6.0 + 6.2)/2 × 1.26 × (9.6 + 8.6)/2 × (8.5 + 4.0) = Col 7 – 8 as before 7th a.b. Col 6 – 7 a.b. 6th a.b. Col 5 – 6 a.b. 5th a.b. Col 4 – 5 = 0.5 × 0.5 × (4.5 − 0.3) × 25 = 4th as before Col 3 – 4 a.b. 3rd a.b. Col 2 – 3 a.b. 2nd a.b. Col 1 – 2 a.b. 1st a.b. Col G – 1 a.b. At above ground floor

Qk Cumulative From total item

Cumulative total

Roof

594.5 17.9 594.5 17.9 594.5 17.9 594.5 17.9 594.5 26.3 594.5 26.3 594.5 26.3 594.5 26.3 594.5 26.3

¿

42.0 612.4

42.0 279.7

1224.8

321.7 279.7

1837.2

601.4 279.7

2449.6

881.1 279.7

3070.4

1160.8 279.7

3691.2

1440.5 279.7

4312.0

1720.2 279.7

4932.8

1999.7 279.8

5553.6 5553.6

¿

2279.5 2279.5

147

5.3.3 Design axial load, ground– 1st floor, NEd a) Axial load to Exp. (6.10) NEd = gGGk + gQQk1 + c0gQQki


where gG = gQ = c0,1 = Qk1 = Qki =

1.35 1.50 0.7 (offices) leading variable action (subject to reduction factor aA or an) accompanying action (subject to aA or an)

EC0: Exp. (6.10) & NA EC0: A1.2.2 & NA

EC1-1-1: 6.3.1.2 (10), 6.3.1.2 (11), & NA

where aA = 1 – A/1000 ≥ 0.75 = 1 – 9 × 69.9/1000 = 0.37 ≥ 0.75 = 0.75 an = 1.1 – n/10 for 1 ≤ n ≤ 5 = 0.6 for 5 ≤ n ≤ 10 and = 0.5 for n > 10 where n = number of storeys supported an= 0.6 for 8‡ storeys supported = as an < aA, use an = 0.6

Assuming the variable action of the roof is an independent variable action: NEd = 1.35 × 5553.6 + 1.5 × (2279.5 − 42.0) × 0.6 + 0.7 × 1.5 × 42.0 = 1.35 × 5553.6 + 1.5 × 2237.5 + 0.7 × 1.5 × 42.0 = 7497.4 + 2013.8 + 44.1 = 9555.3 kN To Exp. (6.10), NEd = 9555.3 kN b) Axial load to Exp. (6.10a) NEd = gGGk + c0,1gQQk1 + c0,1gQQki = 1.35 × 5553.6 + 0.7 × 1.5 × 0.6 ( 279.8 + 1999.7) = 7497.4 + 1436.1 = 8933.4 kN To Exp. (6.10a), NEd = 8933.4 kN c) Axial load to Exp. (6.10b) NEd = jgGGk + gQQk1 + c0,1gQQki ‡

According to BS EN 1991–1–1 6.3.1.2[11] the imposed load on the roof is category H and therefore does not qualify for reduction factor an.

148

EC0: Exp. (6.10a) & NA

EC0: Exp. (6.10) & NA

.',3Bgm^kgZe\henfg

assuming the variable action of the roof is an independent variable action: = 0.925 × 1.35 × 5553.6 + 1.5 × (2279.5 − 42.0) × 0.6 + 0.7 × 1.5 × 42.0 = 1.25 × 5553.6 + 1.5 × 2237.5 × 0.6 + 0.7 × 1.5 × 42.0 = 6942.1 + 2013.8+ 44.1 = 9000.0 kN To Exp. (6.10b), NEd = 9000.0 kN


5.3.4 First order design moments, M a) Grid C Consider grid C to determine Myy in column (about grid 2) gk = 6.1 x 8.5 = 51.9 kN/m

3

qk = 6.1 x 4.0 = 24.4 kN/m

2

300 thick ave 6100 wide

8600

4500

1 500 sq

4500

9600

Actions: gk = (6.0 + 6.2)/2 × 8.5 = 51.9 kN/m qk = (6.0 + 6.2)/2 × 4.0 = 24.4 kN/m Relative stiffness of lower column: Assuming remote ends of slabs are pinned, relative stiffness blcdlc3/Llc = 3 3 blcdlc /Llc + bucduc /Luc + 0.75b23d233/L23 + 0.75b21d213/L21 where b = breadth d = depth L = length lc = lower column, uc = upper column 23 = beam 23, similarly 21 = beam 21 0.54/4.5 = 4 2 × 0.5 /4.5 + 0.75 × 6.1 × 0.33/8.6 + 0.75 × 6.1 × 0.33/9.6 = 0.0139/(0.0278 + 0.0144 + 0.0129) = 0.252

149


1st order moment using Exp. (6.10) FEM 23‡ = 1.35 × 51.9 × 8.62/12 = 431.8 kNm FEM 21 = (1.35 × 51.9 + 1.5 × 24.4) × 9.62/12 = 106.7 × 9.62/12 = 819.5 kNm Mlower,yy = 0.252 × [819.5 – 431.8] = 97.7 kNm 1st order moment using Exp. (6.10a) FEM 23 = 1.25 × 51.9 × 8.62/12 = 399.8 kNm FEM 21 = (1.25 × 51.9 + 1.5 × 24.4) × 9.62/12 = 101.5 × 9.62/12 = 779.5 kNm Mlower,yy = 0.252 × (779.5 – 399.8) = 95.7 kNm 1st order moment using Exp. (6.10b) FEM 23 = 1.35 × 51.9 × 8.62/12 = 431.8 kNm FEM 21 = (1.35 × 51.9 + 0.7 × 1.5 × 24.4 ) × 9.62/12 = 95.7 × 9.62/12 = 735.0 kNm Mlower,yy = 0.252 × (735.0 – 431.8) = 76.4 kNm = Exp. (6.10a) critical b) Grid 2 Consider grid 2 to determine Mzz in column (about grid C)

qk = 45.9 kN/m

B

gk = 97.5 kN/m

C

300 thick ave 11470 wide

4500

D

4500

500 sq

6200

6000

Figure 5.8 Subframe on column C2 along grid 2 Actions: gk = 0.63 × (8.6 + 9.6) × 8.5 = 11.47 × 8.5 = 97.5 kN/m qk = 11.47 × 4.0 = 45.9 kN/m Relative stiffness of lower column: Assuming remote ends of slabs are fixed, relative stiffness ‡ FEM

150

23 = Fixed end moment in span 23 at grid 2.

Cl. 5.8.3.2(4) PD 6687

.',3Bgm^kgZe\henfg

=

0.54/4.5 2 × 0.54/4.5 + 11.47 × 0.33/6.2 +11.47 × 0.33/6.0

= 0.0139/(0.0278 + 0.0500 + 0.0516) = 0.107


1st order moment using Exp. (6.10) FEM CB = (1.35 × 97.5 + 1.5 × 45.9) × 6.22/12 = 200.5 × 6.22/12 = 642.3 kNm FEM CD = 1.35 × 97.5 × 6.02/12 = 394.9 kNm Mlower,zz = 0.107 × (642.3 – 394.9) = 26.5 kNm 1st order moment using Exp. (6.10a) FEM CB = 1.25 × 97.5 × 6.02/12 = 365.6 kNm FEM CD = (1.25 × 97.5 + 1.5 × 45.9) × 6.22/12 = 190.7 × 6.22/12 = 611.0 kNm Mlower,zz = 0.107 × (611.0 – 365.6) = 26.3 kNm 1st order moment using Exp. (6.10b) FEM CB = (1.35 × 97.5 + 0.7 × 1.5 × 45.9) × 6.22/12 = 190.7 × 6.22/12 = 576.0 kNm FEM CD = 1.35 × 97.5 × 6.02/12 = 394.9 kNm Mlower,zz = 0.107 × (576.0 – 394.9) = 19.4 kNm = Exp. (6.10a) critical again

5.3.5 Summary of design forces in column C2 ground–1st Design forces Method

NEd

Using Exp. (6.10) Using Exp. (6.10a) Using Exp. (6.10b)

9555.3 kN 8933.4 kN 9000.0 kN

Myy about grid 2 97.7 kNm 95.7 kNm 76.4 kNm

Mzz about grid C 26.5 kNm 26.3 kNm 19.4 kNm

Notes: 1) To determine maximum 1st order moments in the column, maximum out-ofbalance moments have been determined using variable actions to one side of the column only. The effect on axial load has, conservatively, been ignored. 2) It may be argued that using coefficients for the design of the slab and reactions to the columns does not warrant the sophistication of using Exps (6.10a) and (6.10b). Nevertheless, there would appear to be some economy in designing the column to Exp. (6.10a) or Exp. (6.10b) rather than Exp. (6.10). The use of Exp. (6.10a) or Exp. (6.10b) is perfectly valid and will be followed here.

To avoid duplicate designs for both Exps (6.10a) and (6.10b), a worse case of their design forces will be used, thus: NEd = 9000 kN, Myy = 95.7 kNm, Mzz = 26.3 kNm 151

5.3.6 Design: cover cnom = cmin + Dcdev where cmin = max[cmin,b; cmin,dur] where cmin,b cmin,dur


cmin,dur

Exp. (4.1)

= diameter of bar. Assume 32 mm bars and 8 mm links. = 32 – 8 = 24 mm to link = minimum cover due to environmental conditions. Assume XC1. = 15 mm

cmin = 24 mm, say 25 mm to link Dcdev = 10 mm = cnom = 25 + 10

= 35 mm

Cl. 4.4.1.2(3)

BS 8500-1: Table A4

Cl. 4.4.1.3 & NA

5.3.7 Design: fire resistance Check validity of using Method A and Table 5.2a a) Check l0,fi ≤ 3.0 m where l0 = effective length of column in fire = 0.5 × clear height = 0.5 × (4500 – 300) = 2100 mm b) Check e ≤ emax = 0.15h = 0.15 × 500 = 75 mm e = M0Ed,fi/N0Ed,fi = M0/NEd = 99.5 × 106/8933 × 103 = 11 mm

EC2-1-2: 5.3.2, Table 5.2a

OK

EC2-1-2: 5.3.2(2) OK

c) Check amount of reinforcement ≤ 4% OK Assuming mfi = 0.7 bmin = 350 with OK amin = 40 mm For fire using Method A and Table 5.2a is valid

EC2-1-2: Table 5.2a

5.3.8 Structural design: check slenderness Effective length, l0: l0 = 0.5l [1 + k1/(0.45 + k1)]0.5 [1 + k2/(0.45 + k2)]0.5 where k1 and k2 are relative flexibilities at top and bottom of the column. ki = (EIcol/lcol)/S(2EIbeam/lbeam) ≥ 0.1 ‡ PD 6687 states that to allow for cracking, the contribution of each beam should be taken as 2EI/lbeam

152

Exp. (5.15)

PD 6687[6]‡

.',3Bgm^kgZe\henfg


Critical direction is where k1 and k2 are greatest i.e. where slab spans are greater blcdlc3/Llc k1 = k2 = 2b23d233/L23 + 2b21d213/L21

How to[8]: Columns

= (0.54/4.5)/(2 × 6.1 × 0.33/8.6 + 2 × 6.1 × 0.33/9.6) = (0.0625)/(0.0383 + 0.0343) = 0.86 l0 = 0.5 (4500 – 300) [1 + 0.86/(0.45 + 0.86)]0.5 [1 + 0.86/(0.45 + 0.86)]0.5 l0 = 0.5 × 4200 × 1.66 = 0.828 × 4200 = 3478 mm Slenderness ratio, l: l = l0/i where i = radius of gyration = (I/A)0.5 = h/120.5 = l = 3478 × 120.5/500 = 24.1

Cl. 5.8.3.2(1)

Limiting slenderness ratio, llim: llim = 20 ABC/n0.5 where A = 1/(1 + 0.2 fef). Assume 0.7 as per default B = (1 + 200)0.5. Assume 1.1 as per default C = 1.7 – kf where kf = M01/M2 = –84.9/109.3 = –0.78 C = 1.7 + 0.78 = 2.48 n = NEd /Acfcd = 8933 × 103/(5002 × 0.85 × 50/1.5) = 1.26 = llim = 20 × 0.7 × 1.1 × 2.48/1.260.5 = 34.0 = as l < llim column is not slender and 2nd order moments are not required

Cl. 5.8.3.1(1) & NA Exp. (5.13N)

5.3.9 Design moments, MEd MEd = M + eiNEd ≥ e0NEd

where M = moment from 1st order analysis eiNEd = effect of imperfections

Cl. 5.8.8.2(1), 6.1(4)

Cl. 5.8.8.2(1)

153

where ei = l0/400 e0NEd = minimum eccentricity

Cl. 5.2.7 Cl. 6.1(4)


where e0 = h/30 ≥ 20 mm MEdyy = 95.7 + (3570/400) × 8933 × 10−3 ≥ 0.02 × 8933 = 95.7 + 79.7 ≥ 178.7 = 175.4 < 178.7 kNm MEdzz = 18.8 + 79.7 ≥ 178.7 = 178.7 kNm = Both critical. However, imperfections need only be taken in one direction – where they have the most unfavourable effect = Use MEdzz = 178.7 with MEdyy = 95.7 kNm

Cl. 5.8.9(2)

5.3.10 Design using charts MEdyy /bh2fck = 178.9 × 106/(5003 × 50) = 0.03 NEd/bhfck = 9000 × 103/(5002 × 50) = 0.72 Choice of chart based on d2/h where d2 = depth to centroid of reinforcement in half section assuming 12 bar arrangement with H32s d2 = 35 + 8 + (32/2) + (2/6) [500 + 2 × (35 + 8 + 32/2 )/3] = 59 + (1/3) × 127 = 101 Use Figure C5d) = d2/h = 101/500 = 0.2

Figs C5a) to C5e)

d2 CL

d2, to centroid of reinforcement in half section From Figure C5d) Asfyk/bhfck = 0.30 = 0.29 × 500 × 500 × 50/500 As = 7500 mm2 Try 12 no. H32 (9648 mm2)‡

‡ Using design actions to Exp. (6.10) would have resulted in a requirement for 8500 mm2.

154

Fig. C5d)

.',3Bgm^kgZe\henfg

Cl. 5.8.9

5.3.11 Check biaxial bending


Slenderness: ly ≈ lz = OK. Eccentricities: as h = b check ey/ez MEdz critical. (Imperfections act in z direction.) 95.7 × 106/9000 × 103 ey/ez = 178.7 × 106/9000 × 103 = 0.54 i.e. > 0.2 and < 5 = Design for biaxial bending.

Cl. 5.8.9(3)

Cl. 5.9.3(3), Exp. (5.38b)

C z ey

MEdy

*

b

Centre of reaction

ez y 2

MEdz

h

Figure 5.10 Eccentricities

5.3.12 Design for biaxial bending Check (MEdz/MRdz)a + (MEdy/MRdy)a ≤ 1.0 For load case 2 where MEdz = 178.7 kNm MEdy = 95.7 kNm MRdz = MRdy = moment resistance. Using charts: From Figure C4d), for d2/h = 0.20 and Asfyk/bhfck = 9648 × 500/500 × 500 × 50 = 0.39 NEd/bhfck = 9000 x 103/(5002 x 50) = 0.72 2 MRd/bh fck = 0.057

Cl. 5.9.3(4), Exp. (5.39)

Fig. C5d)

= MRd ≈ 0.057 × 5003 × 50 = 356.3 kNm

155


a = exponent dependent upon NEd/NRd where = Acfcd + Asfyd NRd = 500 × 500 × 0.85 × 50/1.5 + 9648 × 500/1.15 = 7083 + 3216 = 10299 kN NEd/NRd = 9000/10299 = 0.87. Interpolating between values given for NEd/NRd = 0.7 (1.5) and for NEd/NRd = 1.0 (2.0) = a = 1.67

Cl. 5.8.3(4)

Notes to Exp. (5.39)

Check (MEdz/MRdz)a + (MEdy/MRdy)a ≤ 1.0 (178.7/356.3)1.67 + (95.7/356.3)1.67

= 0.32 + 0.11 = 0.43 i.e. < 1.0 = OK Use 12 no. H32

5.3.13 Links Minimum diameter of links: = f/4 = 32/4 = 8 mm Spacing, either: a) 0.6 × 20 × f = 12 × 32 = 384 mm, b) 0.6 × h = 0.6 × 500 = 300 mm or c) 0.6 × 400 = 240 mm. = Use H8 links at 225 mm cc Number of legs: Bars at 127 mm cc i.e. < 150 mm = no need to restrain bars in face but good practice suggests alternate bars should be restrained. = Use single leg on face bars both ways @ 225 mm cc

5.3.14 Design summary 12 H32 H8 links @ 225 cc 35 mm to link 500 mm sq fck = 50 MPa

Figure 5.11 Design summary: internal column

156

Cl. 9.5.3 & NA

Cl. 9.5.3(3), 9.5.3(4)

Cl. 9.5.3(6) SMDSC: 6.4.2

.'-3LfZeei^kbf^m^k\henfg .'- Small perimeter column subject to two-hour fire resistance Mabl \Ze\neZmbhg bl bgm^g]^] mh lahp Z lfZee le^g]^k \henfg ln[c^\m mh Z k^jnbk^f^gm _hk +&ahnkËk^k^lblmZg\^'Bmbl[Zl^]hgma^^qZfie^lahpgbgL^\mbhg-'+' Ikhc^\m]^mZbel


Small perimeter column subject to two-hour fire resistance

chg

Ch[gh'

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

The middle column, B, in Figure 4.5, supports two levels of storage loads and is subject to an ultimate axial load of 1824.1 kN‡. From analysis it has moments of 114.5 kNm in the plane of the beam and 146.1 kNm perpendicular to the beam (i.e. about the z axis). The column is 350 mm square, 4000 mm long, measured from top of foundation to centre of slab. It is supporting storage loads, in an external environment (but not subject to de-icing salts) and is subject to a 2-hour fire resistance requirement on three exposed sides. Assume the base is pinned. Slab 300 450 350 x 350 column 4000 Paving

Foundation

Figure 5.12 Perimeter column

5.4.1 Cover Nominal cover, cnom cnom = cmin + Dcdev where cmin = max[cmin,b; cmin,dur]

Exp. (4.1)

‡

Gk = 562.1; Qk = 789.1; as column supports loads from 2 levels an = 0.9; as imposed loads are from storage c0 = 1.0 =gQ = 1.50 and gQ= 1.35. =Ultimate axial load, NEd = 1.35 × 562.1 + 1.5 × 0.9 × 789.1 = 1824.1 kN. 157


where cmin,b

= diameter of bar. Assume 32 mm main bars and 10 mm links cmin,dur = minimum cover due to environmental conditions. Assuming primarily XC3/XC4, secondarily XF1, cmin,dur = 25 mm Dcdev = allowance in design for deviation = 10 mm = Try cnom = 32 + 10 = 42 mm to main bars or = 25 + 10 = 35 mm to 8 mm links Try cnom = 35 mm to 8 mm links.

Cl. 4.4.1.2(3) BS 8500-1[14] : Table A4

5.4.2 Fire resistance a) Check adequacy of section for R120 to Method A Axis distance available = 43 mm + f/2 Required axis distance to main bars, a for 350 mm square column For mfi = 0.5, a = 45 mm; and for mfi = 0.7, a = 57 mm, providing:

EC1-1-2: 5.3.1(1) & NA 5.3.2, Table 5.2a

t 8 bars used – OK but check later t l0,fi ≤ 3 m – OK but check t e ≤ emax = 0.15h = 0.15 × 350 = 52 mm but e = M0Ed,fi/N0Ed,fi = 0.7 × 146.1 × 106/0.7 × 1824.1 × 103 = 80 mm = no good Try Method B b) Check adequacy of section for R120 to Method B Determine parameters n, w, and e, and check lfi. Assume 4 no. H32 + 4 no. H25 = (5180 mm2: 4.2%) (say 4.2% OK – integrity OK) n = N0Ed,fi/0.7(Acfcd + Asfyd) = 0.7 × 1824.1 × 103/0.7 (350 × 350 × acc × fck/ gC + 5180 × 500/gS) = 1276.9 × 103/0.7 (350 × 350 × 0.85 × 30/1.5 + 5180 × 500/1.15) = 1276.9 × 103/0.7 (2082.5 + 2252.0) = 0.42 OK w = mechanical ratio = Asfyd/Acfcd ≤ 1.0 = 2252/2082 = 1.08 ≥ 1 But say within acceptable engineering tolerance =use w = 1.0 OK e = first order eccentricity = M0Ed,fi/N0Ed,fi 158

EC2-1-2: 5.3.3, Table 5.2b Cl. 9.5.2(3) EC2-1-2: Exp. (5.8a)

EC2-1-2: 5.3.3(2)

EC2-1-2: Exp. (5.8b)


.'-3LfZeei^kbf^m^k\henfg

= 0.7 × 146.1 × 106/0.7 × 1824.1 × 103 = 80 mm as before z 0.23h. OK lfi = slenderness in fire = l0,fi/i where l0,fi = effective length of column in fire = 0.7l = 0.7 × 4000 = 2800 mm i = radius of gyration = h/3.46 for a rectangular section = lfi = 2800/(350/3.46) = 27.7 < 30 = OK Table 5.2b valid for use in this case. Interpolating from BS EN 1992–1–2 Table 5.2b for n = 0.42 and w = 1.0, column width = 350 mm and axis distance = say, 48 mm = Axis distance = 43 mm + f/2 is OK c) As additional check, check adequacy of section to Annex B3 and Annex C Using BS EN 1992–1–2 Table C.8 For w = 1.0, e = 0.25b, R120, l = 30 and interpolating between n = 0.3 and n = 0.5, bmin = 350 mm, amin = 48 mm. = Axis distance = 43 mm + f/2 is OK = 4 no. H32 + 4 no. H25 with 35 mm cover to 8 mm links (a = 55 mm min.) OK

EC2-1-2: 2.4.2(3)

EC2-1-2: 5.3.2(2) Note 2

EC2-1-2: 5.3.3(1), Annex C & NA EC2-1-2: Annex C(2)

5.4.3 Structural design: check slenderness about z axis Effective length, l0, about z axis: l0z = 0.5l [1 + k1/(0.45 + k1) ]0.5 [1 + k2/(0.45 + k2) ]0.5 where l = clear height between restraints = 4000 – 300/2 = 3850 mm k1, k2 = relative flexibilities of rotational restraints at ends 1 and 2 respectively k1 = [EIcol/lcol]/[2EIbeam1/lbeam1 + 2EIbeam2/lbeam2] ≥ 0.1 where Treating beams as rectangular and cancelling E throughout: = 3504/(12 × 3850) = 3.25 × 105 Icol/lcol Ibeam1/lbeam1 = 8500 × 3003/12 × 6000 = 31.8 × 105 Ibeam2/lbeam2 = 0

Exp. (5.15) PD 6687: 2.10

Cl. 5.8.3.2(3) PD 6687

k1 = 3.25/(2 × 31.8) = 0.051 ≥ 0.1 k1 = 0.1 k2 = by inspection (pinned end assumed) = ∞ 159

= l0z = 0.5 × 3850 × [1 + 0.1/(0.45 + 0.1) ]0.5 [1 + ∞/(0.45 + ∞)]0.5 = 0.5 × 3850 × 1.087 × 1.41 = 0.77 × 3850 = 2965 mm


Slenderness ratio, lz: lz = l0z/i where i = radius of gyration = h/3.46 lz = 3.46l0z/h = 3.46 × 2965/350

Cl. 5.8.3.2(1)

= 29.3

Limiting slenderness ratio, llim: llim,z = 20 ABC/n0.5

Cl. 5.8.3.1(1) Exp. (5.13N)

where A = 0.7 B = 1.1‡ C = 1.7 – rm where rm = M01/M02 say M01 = 0 (pinned end) =rm = 0 C = 1.7 – 0 = 1.7 n = relative normal force = NEd/Acfcd = 1824.1 × 103/(3502 × 0.85 × 30/1.5) = 0.88 = llim,z = 20 × 0.7 × 1.1 × 1.7/0.880.5

= 27.9 = As lz > llim,z column is slender about z axis.

5.4.4 Check slenderness on y axis Effective length, l0, about z axis: l0y = 0.5ly [1 + k1/(0.45 + k1) ]0.5 [1 + k2/(0.45 + k2) ]0.5 where ly = clear height between restraints = 4000 + 300/2 – 750 = 3400 mm = relative column flexibility at end 1 k1 = (Icol/Icol)/[S2(Ibeam/Ibeam)] where Icol /Icol = 3504/12 × 3400 = 3.68 × 105

‡ On first pass the default value for B is used. It should be noted that in the final design w = Asfyd/Acfcd = 6432 × (500/1.15) / (3502 × 30 × 0.85/1.5) = 2796/2082 = 1.34. So B = (1 + 2 w)0.5 = (1 + 1.34)0.5 = 1.92 and the column would not have been deemed ‘slender’. B = 1.1 relates approximately to a column with fck = 30 MPa and r = 0.4%.

* PD 6687 states that to allow for cracking, the contribution of each beam should be taken as 2EI/lbeam 160

Exp. (5.15)

Cl. 5.8.3.1(1), & NA, EC2-1-2: 5.3.3(2) PD 6687*



Treating beams as rectangular IbeamAB/lbeamAB = 350 × 7503/[12 × (9000 – 350)] = 14.2 × 105 IbeamBC/lbeamBC = 350 × 7503/[12 × (8000 – 350)] = 16.1 × 105 k1 = 3.68/(2 × (16.1 + 14.2) = 0.060 ≥ 0.1 k1 = 0.1 k2 = ∞ (pinned end assumed) =l0y = 0.5 × 3400 [1 + 0.1/(0.45 + 0.1) ]0.5 [1 +Ƹ/(0.45 + ∞) ]0.5 = 0.5 × 3400 × 1.087 × 1.41 = 0.77 × 3400 = 2620 mm Slenderness ratio, ly: ly = 3.46l0y/h = 3.46 × 2620/350

Exp. (5.15)

= 25.9

Limiting slenderness ratio, llim: llim,y = llim,z = 27.9 As ly < llim,y, column not slender in y axis.

5.4.5 Design moments: MEdz about z axis MEdz = max[M02; M0Ed + M2; M01 + 0.5M2] where M02 = Mz + eiNEd ≥ e0NEd where Mz = 146.1 kNm from analysis eiNEd = effect of imperfections

where ei = l0/400 e0 = 20 mm = M02 = 146.1 + (2965/400) × 1824.1 ≥ 0.02 × 1824.1 = 146.1 + 13.4 > 36.5 = 159.5 kNm

Cl. 5.8.8.2 Cl. 5.8.8.2(1), 6.1.4

Cl. 5.2.7

M0Ed = equivalent 1st order moment at about z axis at about mid-height may be taken as M0ez where M0ez = (0.6M02 + 0.4M01) ≥ 0.4M02 = 0.6 × 159.5 + 0.4 × 0 ≥ 0.4 × 159.5 = 95.7 kNm = nominal 2nd order moment = N>]e2 M2 where e2 = (1/r) l02/10 where 1/r = curvature = KvKh[fyd/(Es × 0.45d)] where Kv = a correction factor for axial load = (nu – n)/(nu – nbal)

Cl. 5.8.8.2(2) Cl. 5.8.8.2(3) Cl. 5.8.8. 3 Exp. (5.34)

161


where nu = 1 + w where w = mechanical ratio = Asfyd/Acfd = 1.08 as before nu = 2.08 n = NEd/Acfcd = 1824.1/2082 = 0.88 nbal = the value of n at maximum moment resistance = 0.40 (default) (2.08 – 0.88)/(2.08 – 0.40) 1.20/1.68 = 0.71 a correction factor for creep 1 + bhef

Kv = = Kh = = where b = = = = hef = =

0.35 + (fck/200) – (l/150) 0.35 + 30/200 – 29.3/150 0.35 + 0.15 – 0.195 0.305 effective creep coefficient‡ h(∞,t0) M0,Eqp/M0Ed

where h(∞,t0) = final creep coefficient = from Figure 3.1 for inside conditions h = 350 mm, C30/37, t0 = 15 ƺ 2.4 M0,Eqp = 1st order moment due to quasipermanent loads Gk + h2 Qk × Mz + eiNEd ≈ jgGGk + h0gQQk = =

M0Ed

Cl. 5.8.4(2)

Cl. 3.1.4(2) Fig. 3.1a

63.3 + 0.8 × 46.0 × Mz + eiNEd 1.35 × 63.3 + 1.5 × 46.0 100.1 × 146.1 + 13.4 154.5

= 108.1 kNm = M02

= 159.5 kNm

‡

With reference to Exp. (5.13N), hef may be taken as equal to 2.0. However, for the purpose of illustration the full derivation is shown here.

162

Exp. (5.1.3N)



Kh = 1 + 0.305 × 2.4 × 108.1/159.5 = 1.50 fyd = 500/1.15 = 434.8 MPa Es = 200000 MPa d = effective depth = 350 – 35 – 8 – 16 = 291 mm 1/r = 0.71 × 1.50 × 434.8/(200000 × 0.45 × 291) = 0.0000177 l0 = 2965 mm as before e2 = (1/r) l02/10 = 15.6 mm = 0.0000177 × 29652/10 =M2 = NEde2 = 1824.1 × 103 × 15.6 = 28.4 kNm =0 M01 = MEdz = max[M02z; M0Edz + M2; M01 + 0.5M2] = max[159.5; 95.7 + 28.4; 0 + 28.4/2] = 159.5 kNm

Mz = 146.1 kNm

+

Mz = 0

M2/2 = 14.2 kNm

a) 1st order moments from analysis

MEdz = 159.5 kNm

eiNEd = 13.4 kNm

M2 = 28.4 kNm

Cl. 3.2.7(3)

MOEdz = 95.8 kNm

=

Mz = 0

c) Design moments: MEdz b) Including 2nd order moments: about z axis MEdz = max [M02, MOEd + M2, M01 = 0.5M2]

Figure 5.13 Design moments MEdz

5.4.6 Design moments: MEdy about y axis

MEdy = max[ M02y ; M0Edy + M2 ; M01 + 0.5M2]

where M02y = = = M0Edy = =

§

My + eiNEd ≥ e0NEd 114.5 + 13.4§ ≥ 36.7 kNm 127.9 kNm (0.6M02y + 0.4 M01y) ≥ 0.4M02y 0.6 × 114.5 + 0.4 × 0

Imperfections need to be taken into account in one direction only.

Cl. 5.8.9(2) 163

M2

= 68.7 kNm = 0 (as column is not slender not slender about y axis). = MEdy = 127.9 kNm

5.4.7 Design in each direction using charts = 1824.1 × 103/(3502 × 30) = 0.50 2 MEd/bh fck = 159.5 × 106/(3503 × 30) = 0.124 Assuming 8 bar arrangement, centroid of bars in half section: d2 ≥ 35 + 8 + 16 + (350/2 – 35 –8 – 16) × 1/4 ƽ 59 + 29 = 88 mm d2/h = 0.25


In z direction: NEd/bhfck

From Figure C4e) Asfyk/bhfck = 0.50 = 0.50 × 3502 × 30/500 = 3675 mm2 As = 4 no. H32 + 4 no. T25 (5180 mm2) OK.

Fig. C4e)

Fig. C4e)

In y direction: MEd/bh2fck = 127.9 × 106/(3503 × 30) = 0.10 NEd/bhfck = 0.50 From Figure C4e) Asfyk/bhfck = 0.34 = 0.34 × 3502 × 30/500 = 2499 mm2 As = 4 no. H32 + 4 no. T25 (5180 mm2) OK.

5.4.8 Check biaxial bending ly ≈ lz = OK. ez = MEdy/NEd ey = MEdz/NEd MEdz 159.5 ey/heq = = = 1.25 MEdy 127.9 ez/beq = need to check biaxial bending (MEdz/MRdz)a + (MEdy/MRdy)a ≤ 1.0 where MRdz = MRdy = moment resistance= Using Figure C4e) Asfyk/bhfck = 5180 × 500/(3502 × 30) = 0.70 for NEd/bhfck = 0.50 MEd/bh2fck = 0.160 = MRd = 0.160 × 3503 × 30 164

Exp. (5.38a)

Exp. (5.38b)

Exp. (5.39)

Fig. C4e)



= 205.8 kNm a depends on NEd/NRd where = Acfcd + Asfyd NRd = 3502 × 0.85 × 30/1.5 + 5180 × 500/1.15 = 2082.5 + 2252.2 = 4332.7 kN NEd/NRd = 1824.1/4332.7 = 0.42 = a = 1.27 (159.5/205.8)1.27 + (114.5/205.8)1.27 = 0.72 + 0.47 = 1.19 = No good = Try 8 no. T32 (6432 mm2) For Asfyk/bhfck = = for NEd/bhfck = = MEd/bh2fck = MRd =

6432 × 500/(3502 × 30) 0.88 0.50 0.187 240.5 kNm

Check biaxial bending (159.5/245.7)1.27 + (114.5/245.7)1.27

= 0.59 + 0.39

Cl. 5.8.9(4)

Fig. C4e)

= 0.98 OK

5.4.9 Check maximum area of reinforcement As/bd = 6432/3502 = 5.2% > 4% However, if laps can be avoided in this single lift column then the integrity of the concrete is unlikely to be affected and 5.2% is considered OK. OK

Cl. 9.5.2(3) & NA

PD 6687: 2.19

5.4.10 Design of links Diameter min. = 32/4 = 8 mm Spacing max. = 0.6 × 350 = 210 mm

Cl. 9.5.3 & NA Cl. 9.5.3(3), 9.5.3(4) = Use H8 @ 200 mm cc

5.4.11 Design summary 8 H32 H8 links @ 200 cc 35 mm cover to link No laps in column section Note The beam should be checked for torsion.

Figure 5.14 Design summary: small perimeter column 165

/ Walls /') General PZeel Zk^ ]^Ëg^] Zl [^bg` o^kmb\Ze ê^f^gml pahl^ e^g`mal Zk^ _hnk mbf^l `k^Zm^k maZg ma^bk mab\dg^ll^l'Ma^bk]^lb`g]h^lghm]b__^klb`gbË\Zgmer_khfma^]^lb`gh_\henfglbgmaZmZqbZe ehZ]lZg]fhf^gmlZ[hnm^Z\aZqblZk^Zll^ll^]Zg]]^lb`g^]_hk' Ma^\Ze\neZmbhglbgmabll^\mbhgbeenlmkZm^ma^]^lb`gh_Zlbgè^la^ZkpZee'


@^g^kZeer%ma^f^mah]h_]^lb`gbg`pZeelblZl_heehpl'BgikZ\mb\^%lô^kZeh_ma^l^lmîlfZr[^ \hf[bg^]' N =^m^kfbg^]^lb`geb_^'

EC0 & NA Table NA 2.1

N :ll^llZ\mbhglhgma^pZee'

EC1 (10 parts) & UK NAs

N =^m^kfbg^pab\a\hf[bgZmbhglh_Z\mbhglZiier'

EC0 & NA: Tables NA A1.1 & NA: A1.2(B)


BS 8500–1

lmk^g`ma' N
k^lblmZg\î^kbh]'

Approved Document B EC2–1–2

N =^m^kfbg^\ho^k_hk_bk^%]nkZ[bebmrZg][hg]'

Cl. 4.4.1

N :gZerl^lmkn\mnk^_hk\kbmb\Ze\hf[bgZmbhgfhf^gml

Section 5

Zg]ZqbZe_hk\^l'

166

N
Section 5.8

N =^m^kfbg^Zk^Zh_k^bg_hk\^f^gmk^jnbk^]'

Section 6.1

N
Sections 8 & 9

PZeel /'* Shear wall >qZfie^ /'* lahpl ma^ ]^lb`g h_ Z lbfie^ ebg^Zk la^Zk pZee Zl mrib\Zeer nl^] bg f^]bnf& kbl^ [nbe]bg`l' LbfbeZk ikbg\bie^l fZr [^ Ziieb^] mh pZeel maZm Zk^ laZi^] Zl<% E%M% S Zg] k^\mZgè^lbg&ieZg%[nmblln^lh_ebfbmbg`ÌZg`^]bf^glbhglZg]la^ZkZm\hkg^klg^^]mh[^ Z]]k^ll^]'Ma^ ^qZfie^ lahpl hger NEL ]^lb`g Zl% ZiZkm _khf fbgbfnf Zk^Zl h_ lm^ê mh \hgmkhe \kZ\dbg`% LEL blln^l Zk^ `^g^kZeer ghg&\kbmb\Ze bg f^]bnf&kbl^ lmkn\mnk^l' ?hk la^Zk pZeelbgabà&kbl^lmkn\mnk^l%k^_^k^g\^lahne][^fZ]^mhli^\bZeblmebm^kZmnk^T+2V'


Ma^^qZfie^blbgm^g]^]mhlahpahpZla^ZkpZeeikhob]bgìZkmh_maêZm^kZelmZ[bebmrbghg^ ]bk^\mbhgbgZf^]bnfkbl^lmkn\mnk^fbàm[^]^lb`g^][raZg]' :qbZeehZ]lZg]Ëklmhk]^kfhf^gmlZk^]^m^kfbg^]'Ma^]^lb`g\hglb]^klle^g]^kg^llbghk]^k mh ]^m^kfbg^ ]^lb`g fhf^gml% F>]% bg ma^ ieZg^ i^ki^g]b\neZk mh ma^ pZee'Ma^ ^__^\ml h_ Zeehpbg`_hkbfi^k_^\mbhglZk^ZelhbeenlmkZm^]' Ikhc^\m]^mZbel

chg

Ch[gh'

Shear wall

web

La^^mgh'

TCC

=Zm^

CCIP – 041 1 Oct 09

Wall A is 200 mm thick and, in addition to providing vertical support to 200 mm flat slabs at roof level and floors 1 to 3, it helps to provide lateral stability to the four-storey office block. Assuming the stair itself provides no lateral stability, the wall is to be designed for the critical section at ground and first floor level using BS EN 1990 Exp. (6.10). The concrete is C30/37. The wall is supported on pad foundations and the ground floor is ground bearing. X 300

1300

4800

4400

Wall A

1500

4800

7200

4800 300 300 3600 6000

6000

6000

6000 2500 300 N

30700

Figure 6 6.11 Typical floor plan 900

X

Roof 3rd

4@3300

2nd 1st

600 900

Gnd

Figure 6.2 Section X–X

167

6.1.1 Actions


Roof

Paving 40 mm Waterproofing Insulation Suspended ceiling Services Self-weight 200 mm slab Imposed load

Floor slabs

Carpet Raised floor Suspended ceiling Services Self-weight 200 mm slab

Permanent Variable actions actions gk qk kN/m2 1.00 0.50 0.10 0.15 0.30 5.00 7.05 0.60

Ground floor slab (ground bearing)

Carpet Raised floor Services Self-weight 200 mm slab

Stairs

150 waist @ 30 Treads 0.15 × 0.25 × 25 × 4/2 = Screed 0.05 × 22 = Plaster Tiles and bedding

Section 2.4.2

3.00

Section 2.4.2 Section 2.8

4.40 1.88 1.10 0.21 1.00 8.59 2.50

Imposed load

168

2.50 0.03 0.30 0.15 5.00 5.48

Imposed load

Cavity wall

102 mm brickwork 50 mm insulation 100 mm blockwork Plaster

2.37 0.02 1.40 0.21 4.00

RC wall

200 mm wall Plaster both sides

5.00 0.42 5.42

Wind

wk =

Section 2.4.2

Section 2.8

0.03 0.30 0.15 0.30 5.00 5.78

Imposed load

Section 2.8

Section 2.4.2 Section 2.8

Section 2.8

1.10

EC1-1-4 & NA

/'*3La^ZkPZee


6.1.2 Load take-down Consider whole wall. Gk Item Calculation From item Cum. total Roof (6.0/2 + 2.5/2) × (4.4 + 1.5/2) × (7.05 + 0.6) = 154.3 Roof (6.0/2) × (1.3/2) × (7.05 + 0.6) = 13.7 Wall 3.3 × 4.4 × 5.42 = 78.7 246.7 At above 3rd floor 246.7 3rd floor (6.0/2) × (1.3/2 + 4.4 + 1.5/2) × (5.78 + 2.5) = 100.6 Landing (2.5/2 × 1.5/2) × (5.78 + 2.5) 11.6 Wall a. b. 78.7 Stair say 1.1 × 4.4 (8.59 + 2.5) 41.6 232.5 At above 2nd floor 479.2 2nd floor, landing, wall and stair a. b. 232.5 At above 1st floor 711.7 1st floor, landing, wall and stair a. b. 232.5 At above ground floor 944.2 Ground floor assume 1 m all round = 2 × (1.3/2 + 4.40 + 1.5/2) × (5.48 + 3.0) = 63.6 250 mm wall to foundation 4.4 × 0.2 × 0.6 × 25 = 13.2 76.8 At above foundation 1021.0

Qk From item Cum. total 13.1 1.2 14.3 14.3 43.5 5.0 12.1 60.6 74.9 60.6 135.5 60.6 196.1 34.8

230.9

6.1.3 Design actions due to vertical load at ground–1st Gk = 944.2 Gk/m = 944.2/4.4 = 214.6 kN/m Qk = an × 196.1 where an = 1.1 – n/10 where n = no. of storeys qualifying for reduction‡ =3 = 1.1 – 3/10 = 0.8 Qk/m = 156.9/4.4 = 35.7 kN/m = Qk = 0.8 × 196.1 = 156.9 kN

‡

EC1-1-1: 6.3.1.2(11) & NA

Includes storeys supporting Categories A (residential and domestic), B (office), C (areas of congregation) and D (shopping), but excludes E (storage and industrial), F (traffic), G (traffic) and H (roofs). 169

6.1.4 Vertical loads from wind action: moments in plane Consider wind loads, N–S 300 3600

6000

6000

6000

6000

2500 300

30700

Wall A

4400

2400

Lift shaft 200 thick walls N

wk = 1.10 kN/m2

Figure 6.3 Lateral stability against wind loads N–S Check relative stiffness of lift shaft and wall A to determine share of load on wall A. Lift shaft: ILS = 2.44/12 – 2.04/12 – 0.2 × 1.63/12 = 1.36 m4 Wall A: IWallA = 0.2 × 4.43/12 = 1.41 m4 where I = inertia = Wall A takes 1.41/(1.41 + 1.36) = 51% of wind load. Check shear centre to resolve the effects of torsion. Determine centre of gravity, CoGL of the lift shaft. 2.4 × 2.4 =

Area, A

Lever arm, x

Ax

5.76

1.2

6.912

–2.0 × 2.0 =

–4.00

1.2

–4.800

–1.6 × 0.2 =

–0.32

2.3

–0.732

1.44

1.38

1600 200 200

2400

2400


2400 o/a

CoGL

x 170

Figure 6.4 Lift shaft

/'*3La^ZkpZee

x = Ax/A = 1.38/1.44 = 0.956 m i.e. from face of lift shaft to CoG of shaft = 2.40 – 0.956 = 1.444 m Shear centre, Cw of walls, from centreline of wall A = or

ILS × (1.44 + 24.00 + 0.05‡) 1.36 × 25.49 = = 12.56 m from wall A 1.36 + 1.41 ILS + IWallA

= 12.56 + 2.80 – 0.05 = 15.31 from east end of building.

24.00 15.31

Wall A

* Cw

CoGL

*

Wk

15.35

Figure 6.5 Shear centre, Cw and centre of action, Wk Centre of action (30.7/2 = 15.35 m from end of building) and shear centre (almost) coincide. = there is no torsion to resolve in the stability system for wind in a N–S direction.# Roof

900 3300 3300 3300 3300 600 900

3rd 14100


1.45

CL Wall A‡ 2.80

2nd

wk = 17.2 kN/m

1st Gnd

Figure 6.6 Wall A – wind loads N–S 300 4400 300

= Wall A takes 51% of wind load, so characteristic wind load on wall A, wk, wall A = 51% × wk × Lx = 51% × 1.1 × 30.7 = 17.2 kN/m ‡ Assuming centreline of wall A is 50 mm to right hand side of grid. #Had

there been significant torsion this would have been resolved into +/– forces in a couple based on the shear walls. 171

= at just above ground floor, characteristic in-plane moment in wall A, Mk, due in this case to wind = 17.2 × 14.12/2 = 1709.8 kNm Resolving into couple using 1 m either end of wall‡, characteristic wind load in each end, Wk = 1709.8/3.4 = ±502.9 kN

6.1.5 Effects of global imperfections in plane of wall A Licensed copy from CIS: kierg, Kier Group, 12/02/2015, Uncontrolled Copy.

Roof

HIR

yI

3rd 2nd 1st Gnd

HI3 HI2 HI1 HIG

Figure 6.7 Global imperfections Global imperfections can be represented by forces Hi at floor level where Hi = yi(Nb – Na) where yi = (1/200) aham where ah = 0.67 ≤ 2/l 0.5 ≤ 1.0 = 0.67 ≤ 2/14.70.5 ≤ 1.0 = 0.67 ≤ 0.52 ≤ 1.0 = 0.67 am = [0.5(1 + 1/m)]0.5 where m = no. of members contributing to the total effect = 25 vertical elements on 4 floors = 100

‡ For medium-rise shear walls there are a number of methods of design. Cl. 9.6.1 suggests strut-and-tie (see Volume 2 of these worked examples[30]). Another method[26] is to determine elastic tensile and compression stresses from NEd/bL +/– 6MEd/bL2 and determine reinforcement requirements based on those maxima. The method used here assumes a couple, consisting of 1.0 m of wall either end of the wall. The reinforcement in tension is assumed to act at the centre of one end and the concrete in compression (with a rectangular stress distribution) acts at the centre of the other end. The forces generated by the couple add or subtract from the axial load in the 1 m ends of the walls. The method is useful for typical straight shear walls of say 2.5 to 5.0 m in length.

172

Exp. (5.4) Cl. 5.2(1), 5.2(5), 5.2(8) & NA

Vol. 2

/'*3La^ZkpZee

= am = 0.71 = yi = 0.67 × 0.71/200 = 0.0024 = axial forces in members below and above Nb, Na (Nb – Na) = axial load from each level


At roof level Area = 30.4 × 14.5 – 1.3 × 2.5 – 3.6 × 4.8 = 420.3 m3 Perimeter = 2 × (30.4 + 14.5) = 89.8 m (Na – Nb) = axial load from roof level = 420.3 × (7.05 + 0.6) + 89.8 × 0.9 × 4.0 = 3286.4 + 252.2 kN At 3rd floor (Na – Nb) = 420.3 × (5.78 + 2.5) + 89.8 × 3.3 × 4.0

= 3615.7 + 1050.8 kN

At 2nd floor (Na – Nb) = 3615.7 + 1050.8 kN At 1st floor (Na – Nb) = 3615.7 + 1050.8 kN HiR = 0.0024 × (3286.4 + 252.2) = 7.9 + 0.6 = 8.5 kN Hi3 = Hi2 = Hi1 = 0.0024 × (3615.7 + 1050.8) = 8.7 + 2.5 = 11.2 kN Characteristic design moment at ground floor, Mk = 8.5 × 13.2 + 11.2 × (9.90 + 6.60 + 3.30) = 112.2 + 221.8 = 334.0 kNm As before, wall A resists 51% of this moment. Resolving into couple using 1 m either end of wall, = GkH§ = 0.51 × 334.0/3.4 = ± 50.1 kN i.e. GkH = ±50.1 kN/m

6.1.6 Check for global second order effects To check whether the building might act as a sway frame check FV,Ed ≤ kl

SEcd Ic ns = ns + 1.6 L2

Cl. 5.8.3.3(1) Exp. (5.18)

where FV,Ed = Total vertical load (on braced and bracing members) where Floor area = (30.7 – 2 × 0.15) × 14.4 – (2 × 0.15) – 3.6 × 4.8 – 1.3 × 2.5 = 428.6 – 20.5 = 408.1

§ As H derives mainly from permanent actions its resulting effects are i considered as being a permanent action too.

173

Loads from roof: 408 (7.05 + 0.6) = 3–1 floors: 3 × 408 (5.78 + 2.5) = Allow cavity wall at 1st floor and above

Gk 2876 7075

(3 × 3.30 + 0.9) × 2 × (30.4 + 14.1) × 4.0 =

3845 13705

Imposed load reduction 20% (see 6.2.3)


13705

Qk 245 3060

3305 661 2644

=FV,Ed ≈ 13705 × 1.35 + 1.5 × 2644 = 22468 kN = 0.31 kl = number of storeys ns = 4 (including roof) = Ecm/gCE = 33/1.2 = 27.5 GPa Ecd = Inertia of bracing members Ic in N–S direction Ic = 1.36 + 1.41 = 2.77 m4 (See Section 6.1.4) in E–W direction ILS, with reference to Figure 6.4 h×d 2.4 × 2.4 =

Area, A

×

Ax

Ax 2

I

5.76

1.2

6.912

8.294

2.765

–2.0 × 2.0 = –4.00

1.2

–4.800

–5.760

–1.333

–1.6 × 0.2 = –0.32

2.3

–0.732

–1.683

–0.001

1.38

0.851

1.44

1.431

as before (6.1.4), x = 1.38/1.44 = 0.956 m ILS = INU = Ax 2 + I – Ax 2 = 0.851 + 1.431 – 1.44 × 0.956 = 0.965 m4 L = total height of building above level of moment restraint = 14.7 (see Figure 6.6) Check ns SEcdIc × on weak E–W axis: kl L2 ns + 1.6 = 0.31 × [4/(4 + 1.6)] × 27500 × 103 × (0.965/14.72) = 27200 kN = no need to design for 2nd order effects. i.e. > FV,Ed

174

Cl. 5.8.2(6) & NA Table 3.1, 5.8.6(3) & NA

/'*3La^ZkpZee

6.1.7 Design moments – perpendicular to plane of wall CL 150

650

CL

B 1350

B

1st

4400

A

A Gnd

750


200

up

CL

Figure 6.8 Plan of wall A and location of sections A–A and B–B

Figure 6.9 Section A–A

Section A–A @ 1st floor The slab frames into the wall. For the purposes of assessing fixed end moments, the width of slab contributing to the moments in the wall is assumed to be the length of the wall plus distances half way to adjacent supports either end. Therefore, consider the fixed end moment for 1.50/2 + 4.40 + 1.30/2 = 5.8 m width of adjoining slab framing into the 4.4 m long shear wall (see Figure 6.8).

kw

n ks

kw

Figure 6.10 Subframe section A–A @ 1st floor FEM‡: assuming imposed load is a leading variable action: = nl2/8 = 5.8 (1.35 × 5.78 + 1.5 × 2.5) × 6.02/8 = 5.8 × 11.6 × 62/8 = 302.8 kNm ‡

EC0: Exp. (6.10) & NA

FEM: fixed end moment 175

Similarly, assuming imposed load is an accompanying action: FEM = 5.8 (1.35 × 5.78 + 0.7 × 1.5 × 2.5) × 62/8 = 5.8 × 10.4 × 62/8 = 271.4 kNm =M = 271.4 × 0.42/4.40 = 25.9 kNm/m @ ULS Section A–A @ ground floor By inspection not critical – nominal moment. Section B–B @ 1st Consider the landing influences half of wall (2.2 m long) and that this section of wall is subject to supporting half the slab considered before at 1st floor level at Section A–A. 1st 1650


kw = EI/l = E × 4400 × 2003/(12 × 3300) = E × 8.88 × 105 ks = EI/2l = E × 5800 × 2003/(2 × 12 × 6000) = E × 3.22 × 105 M = 302.8 × 8.88/(2 × 8.8 + 3.22) = 302.8 × 0.42 = 121.2 kNm i.e. 121.2/4.40 = 27.5 kNm/m @ ULS

Landing

Gnd

Figure 6.11 Section B–B FEM = 302.8/2 = 151.4 kNm kw = I/l = 2200 × 2003/(12 × 1650) = 8.88 × 105 ks = 3.22 × 105/2 = 1.61 × 105 M = 151.4 × 8.88/(2 × 8.88 + 1.61) = 151.4 × 0.46 = 69.6 kNm i.e. 63.8/2.2 = 31.6 kNm/m @ ULS 176

/'*3La^ZkpZee

Similarly, assuming imposed load is an accompanying action: FEM = 5.8 (1.35 × 5.78 + 0.7 × 1.5 × 2.5) × 62/8 = 5.8 × 10.4 × 62/8 = 271.4 kNm =M = 271.4 × 0.46/(2 × 2.2) = 28.4 kNm/m @ ULS Section B–B @ landing level and ground floor By inspection not critical


6.1.8 Consider slenderness of wall at ground floor To derive maximum slenderness (at south end of wall), ignore effect of landing. Effective length, l0 = 0.75 × (3300 – 200) = 2325 l = 3.46 × l0/h = 3.46 × 2325/200 = 40.2 Limiting slenderness, llim = 20 ABC/n0.5 where A = 0.7 B = 1.1 C = 1.7 – rm where rm = M01/M02 = say = –0.25 C = 1.95 n = NEd/Acfd where NEd = 214.6 × 1.25 + 31.2 × 1.5 × 0.7 + 502.9 × 1.5 + 98.2 × 1.5 × 0.7‡ = 268.3 + 32.8 + 754.4 + 103.1 = 1158.6 kN Acfd = 200 × 1000 × 0.85 × 30/1.5 = 3400 kN = n = 0.34 = llim = 20 × 0.7 × 1.1 × 1.95/0.340.5 = 51.5 = As l < llim wall is not slender and = no secondary moments

Table C16 Cl. 5.8.3.2(1) Cl. 5.8.3.1(1), Exp. (5.13N)

6.1.9 Summary: design forces on wall, ground–1st floor At ground to 1st consider maxima. Vertical loads

Gk = 214.6 kN/m Qk = 35.7 kN/m

Vertical load due to in-plane bending and wind

Wk = ±502.9 kN/m

Vertical load due to in-plane bending and imperfections GkH = ±50.1 kN/m Maximum moment out of plane, floor imposed load as leading action M = 31.6 kN/m @ ULS Maximum moment out of plane, floor imposed load as accompanying action M = 28.4 kN/m @ ULS ‡ Assuming

wind load is lead variable action. 177


6.1.10 Combinations of actions at ground–1st floor a) At ULS, for maximum axial load, Wk is leading variable action NEd = 1.35Gk + 1.5Qk1 + 1.5c0Qki = 1.35 (214.6 + 50.1) + 1.5 × 502.9 + 1.5 × 0.7 × 35.7 = 357.3 + 754.4 + 37.5 = 1149.2 kN/m MEd = M + eiNEd ≥ e0NEd where M = moment from 1st order analysis = 28.4 kNm/m ei = l0 /400 = 2325/400 = 5.8 mm e0 = h/30 ≥ 20 mm = 20 mm MEd = 28.4 + 0.0058 × 1149.2.1 ≥ 0.020 × 1149.2 = 28.4 + 6.7 ≥ 23.0 = 35.1 kNm/m b) At ULS, for minimum axial load, Wk is leading variable action NEd = 1.0 × 214.6 – 1.35 × 50.1 – 1.5 × 502.9 + 0 × 35.7 = –607.4 kN/m (tension) MEd = 28.4‡ + 0.0058 × 607.4 ≥ 0.020 × 602.4 = 28.4 + 3.5 ≥ 23.0 = 31.9 kNm/m c) At ULS, for maximum out of plane bending assuming Qk is leading variable action NEd = 1.35 (214.6 + 50.1) + 1.5 × 35.7 + 1.5 × 0.5 × 502.9 = 357.3 + 53.6 + 377.2 = 788.1 kN/m MEd = 31.6 + 0.0058 × 788.1 ≥ 0.020 × 788.1 = 31.6 + 4.6 ≥ 15.8 = 36.2 kNm/m or NEd = 1.0 × 214.6 – 1.35 × 50.1 – 0 × 31.2 – 1.5 × 0.5 × 502.9 = 214.6 – 67.6 – 0 – 377.2 = –230.2 kN/m (tension) MEd = 31.6 + 0.0058 × 230.2 = 33.0 kNm/m d) Design load cases Consolidate c) into a) and b) to consider two load cases: NEd = 1149.4 kN/m, MEd = 36.2 kN/m (out of plane) and NEd = –607.4 kN/m, MEd = 36.2 kN/m (out of plane) ‡

178

Strictly incompatible with Qk = 0. However, allow Qk = 0.

Cl. 5.8.8.2(1), 6.1.4

Cl. 5.2(7), 5.2(9) Cl. 6.1.4

/'*3La^ZkpZee

6.1.11 Design: cover above ground cnom = cmin + Dcdev where cmin = max[cmin,b ; cmin,dur]

Exp. (4.1)


where cmin,b = diameter of bar = 20 mm vertical or 10 mm lacers cmin,dur = for XC1 = 15 mm Dcdev = 10 mm 25 mm to lacers =cnom = 15 + 10 = (35 mm to vertical bars)

6.1.12 Fire resistance Assuming 1-hour fire resistance required for, as a worst case, μfi = 0.7 and fire on both sides. Min. thickness = 140 mm, min. axis distance = 10 mm i.e. not critical

EC2-1-2: Table 5.4

6.1.13 Design using charts For compressive load: d 2/h = (25 + 10 + 16/2)/200 = 0.215 = interpolate between charts C5d) and C5e) for NEd/bhfck = 1149.4 × 103/(200 × 1000 × 30) = 0.192 MEd/bh2fck = 36.2 × 106/(2002 × 1000 × 30) = 0.030 Gives: Asfyk/bhfck = 0 = minimum area of reinforcement required = 0.002 Ac = 0.002 × 200 × 1000 = 400 mm2/m = 200 mm2/m each face max. 400 mm cc, min. 12 mm diameter Try T12 @ 400

e

+

e

=

e

›

Figs C5d), C5e)

Cl. 9.6.2 & NA

Cl. 9.6.2(3); SMDSC

s

As /2

sst2

›

=

+

sst1

As /2 0

0

0

0

Moment

Tension

Combined

Combined

Figure 6.12 Stresses and strains in wall subject to tension and out of p plane moment 179

For tensile load and moment: Working from first principles, referring to Figure 6.12 and ignoring contribution from concrete in tension, NEd and MEd so

= (sst1 + sst2) × As/2 = (sst1 – sst2) × As/2 × (d – d2)

sst1 + sst2 = 2NEd/As


and sst1 – sst2 = 2MEd/[(d – d2)As] =

2sst1

= 2NEd/As + 2MEd/[(d – d2)As]

=

As

= (NEd/sst1) + MEd/(d – d2)sst1

sst1

= fyk/gS = 500/1.15 = 434.8

As

= 607.4 × 103/434.8 + 36.2 × 106/[(157 – 43) × 434.8]

=

= 1397 + 730 = 2127 mm2 sst2

= 2NEd/As – sst1 = 571.7 – 434.8 = 136 MPa

By inspection all concrete is in tension zone and may be ignored. Use 6 no. H16 @ 200 cc both sides for at least 1 m each end of wall (2412 mm2).

6.1.14 Horizontal reinforcement As, hmin = 0.001As or 25% As vert = 200 mm2 or 0.25 × 2036 = 509 mm2/m = requires 254 mm2/m each side Spacing ≤ 400 mm Links not required. Use H10 @ 300 (262 mm2/m) both sides.

Cl. 9.6.3(1) & NA

Cl. 9.6.3(2) Cl. 9.6.4(1)

6.1.15 Check for tension at top of foundation

180

Permanent and variable: = 1021.0/4.4 = 232.0 kN/m Gk = 230.9/4.4 = 52.5 kN/m Qk

Section 6.1.2

Wind: = 17.2 × 14.1 × [14.1/2 + 0.6] = 1855.3 kN/m Mk Resolved into couple 1 m either end of wall = 1855.3/3.4 = ±545.7 kN/m Wkw

Section 6.1.4

Global imperfections: = 8.5 × 13.8 + 11.2 × (10.5 + 7.2 + 3.9 + 0.6) Mk = 365.9 kNm = 365.9 × 0.51/3.4 = 54.9 kN/m GkH

Section 6.1.5

/'*3La^ZkpZee

At ULS for maximum axial tension Wk is lead imposed load: = 1.0 × 232.0 – 1.35 × 54.9 – 1.5 × 545.7 + 0 × 52.5 NEd = –660.7 kN/m = nominal = e2NEd = 0.02 × 660.7 MEd = 13.2 kNm/m

Cl. 6.1.4

As before


As

=

NEd MEd + fyk/gM (d – d2)fyk/gM

= 660.7 × 103/434.8 + 13.2 × 106/[(157 – 43) × 434.8] = 1520 + 266 = 1786 mm2 i.e. not critical = Use 6 no. H16 @ 200 cc b.s. for at least 1 m either end of wall (2412 mm2).

6.1.16 Check for axial compression at top of foundation At ULS for maximum axial compression Wk is lead imposed load: NEd = 1.35 × 232.0 + 1.35 × 54.9 + 1.5 × 545.7 + 0.7 × 1.5 × 52.5 = 1261.0 kN/m MEd = nominal = e2NEd = 0.02 × 1261.0 = 25.2 kNm/m By inspection not critical (minimum reinforcement required). = tension critical as above.

Cl. 6.1.4 Section 6.1.13

6.1.17 Design: cover below ground cnom = cmin + Dcdev where cmin = max[cmin,b ; cmin,dur] where cmin,b = diameter of bar = 16 mm vertical or 10 mm lacers cmin,dur = for assumed Aggressive Chemical Environment for Concrete (ACEC) class AC1 ground conditions = 25 mm

Exp. (4.1)

BS 8500-1 Annex A[14], How to: Building structures[8]

Dcdev = 10 mm cnom = 25 + 10 =

35 mm to lacers (45 mm to vertical bars) In order to align vertical bars from foundation into Gnd–1st floor lift as starter bars, locally increase thickness of wall to say 250 mm thick with cnom = 50 mm

181

6.1.18 Check stability


Assume base extends 0.3 m beyond either end of wall A, i.e. is 5.0 m long and is 1.2 m wide by 0.9 m deep. Overturning moments Wind (see Figure 6.6) Mk = 17.2 × 14.1 × [14.1/2 + 1.5] = 2073.5 kNm Global imperfections (see Section 6.1.5) Mk = 0.51 x [8.5 × 14.7 + 11.2 × (11.4 + 8.1 + 4.8 + 1.5)] = 0.51 x [125.0 + 11.2 × 25.8] = 0.51 x 414.0 = 211 kNm

EC0: Table A1.2(A) & NA Fig. 6.6

Fig. 6.7

Restoring moment Mk = (1021.0 + 5.0 x 1.2 x 0.9 x 25 + 0 x 230.9 ) x (0.3 + 2.2) = 2890 kNm At ULS of EQU, Overturning moment = fn(gQ,1Qk1 + gG,supGk) = 1.5 x 2073.5 + 1.1 x 211.0 = 3342.4 kNm Restoring moment = fn(gG,infGk) = 0.9 x 2890 = 2601 kNm i.e. > 1818.4 kNm

EC0: Table A1.2(A) & NA

= no good

Try 1.05 m outstand Restoring moment Mk = 2890 (1.05 + 2.2) / (0.3 + 2.2) = 3757.0 kNm At ULS, restoring moment = 0.9 x 357.0 = 3381.3 kNm =OK. Use 1.05 m outstand to wall.

6.1.19 Design summary 1st Lacers H10 @ 300 m outside 25 mm cover to 200 mm wall above ground floor H12 @ 400 b.s

1050

182

12

12

24H16 @ 200 Gnd (12NF, 12FF) 50 mm cover to 250 wall below ground floor 1050

EC0: Table A1.2(A) & NA

03K^_^k^g\^lZg]_nkma^kk^Z]bg`

7 References and further reading References


1 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22+¾*¾*%>nkh\h]^+¾IZkm*¾*3=^lb`gh_ \hg\k^m^lmkn\mnk^l¾@^g^kZekne^lZg]kne^l_hk[nbe]bg`l';LB%+))-' 1a GZmbhgZe:gg^qmh>nkh\h]^+¾IZkm*¾*';LB%+)).' 2 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22+¾*¾+%>nkh\h]^+¾IZkm*¾+3=^lb`gh_ \hg\k^m^lmkn\mnk^l¾@^g^kZekne^l¾Lmkn\mnkZe_bk^]^lb`g';LB%+))-' 2a GZmbhgZe:gg^qmh>nkh\h]^+¾IZkm*¾+';LB%+)).'

3 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22+¾+%>nkh\h]^+¾IZkm+3=^lb`gh_ \hg\k^m^lmkn\mnk^l¾;kb]`^l';LB%+)).' 3a GZmbhgZe:gg^qmh>nkh\h]^+¾IZkm+';LB%+))0'

4 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22+¾,%>nkh\h]^+¾IZkm,3=^lb`gh_ \hg\k^m^lmkn\mnk^l¾Ebjnb]&k^mZbgbg`Zg]\hgmZbgf^gmlmkn\mnk^l';LB%+))/' 4a GZmbhgZe:gg^qmh>nkh\h]^+¾IZkm,';LB%+))0'

5 K LG:K:R:G:G<A@HH=nkh\h]^+' <

6 ; KBMBLALM:G=:K=LBGLMBMNMBHG'I=//10;Z\d`khng]iZi^kmhma^NDGZmbhgZe :gg^q^l;L>G*22+¾*';LB%+))/'

7 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L1**)Lmkn\mnkZenl^h_\hg\k^m^¾IZkm*3

8 ; KHHD>K%H^mZe'Ahpmh]^lb`g\hg\k^m^lmkn\mnk^lnlbg`>nkh\h]^+'<

9 M A>BGLMBMNMBHGH?LMKNG@BG>>KL(MA>M>LHMR(=MB'LmZg]Zk] f^mah]h_]^mZbebg`lmkn\mnkZe\hg\k^m^%Mabk]>]bmbhg'BLmkn\m>%+))/'

10 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22)%>nkh\h]^3;Zlblh_lmkn\mnkZe]^lb`g' ;LB%+))+' 10a GZmbhgZe:gg^qmh>nkh\h]^';LB%+))-' 11 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22*%>nkh\h]^*3:\mbhglhglmkn\mnk^l !*)iZkml"';LB%+))+¾+))/' 11a GZmbhgZe:gg^q^lmh>nkh\h]^*';LB%+)).¾+))1Zg]bgikîZkZmbhg' 12 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*220¾*%>nkh\h]^0'@^hm^\agb\Ze]^lb`g' @^g^kZekne^l';LB%+))-' 12a GZmbhgZe:gg^qmh>nkh\h]^0;L>G*220¾*';LB%+))0' 13 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*221¾*%>nkh\h]^1'=^lb`gh_lmkn\mnk^l_hk ^ZkmajnZd^k^lblmZg\^'@^g^kZekne^l'L^blfb\Z\mbhgl_hk[nbe]bg`l';LB%+))-' 13a GZmbhgZe:gg^qmh>nkh\h]^1;L>G*221¾*';LB%+))1'

14 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L1.))¾*3G+)/¾*3F^mah]h_li^\b_rbg`Zg]`nb]Zg\^mhma^li^\b_b^k';LB%+))+'

15 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L---23Lm^ê_hkma^k^bg_hk\^f^gmh_\hg\k^m^¾ Pê]Z[e^k^bg_hk\bg`lm^ê¾;Zk%\hbeZg]]^\hbe^]ikh]n\m¾Li^\b_b\Zmbhg';LB%+)).'

16 < HGLMKN]bmbhg%

17 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*,/0)3>q^\nmbhgh_\hg\k^m^lmkn\mnk^l¾IZkm*3

18 < HGLMKN

19 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L1///3+)).%L\a^]nebg`%]bf^glbhgbg`%[^g]bg` Zg]\nmmbg`h_lm^ê_hkk^bg_hk\^f^gm3Li^\b_b\Zmbhg';LB%+)).'


20 M A>JN>>G LIKBGM>KH?:GM%Ma^;nbe]bg`K^`neZmbhgl+)))'Ma^ LmZmbhg^krH__b\Êbfbm^]%+)))'

21 M A>LM:MBHG>KRH??B<>EBFBM>=!MLH"%;nbe]bg`!:f^g]f^gm"!Gh+"K^`neZmbhgl+))+ Zg]ma^;nbe]bg`!:iikho^]Bgli^\mhkl^m\'"!:f^g]f^gm"K^`neZmbhgl+))+'MLH%+))+'

22 ; KBMBLALM:G=:K=LBGLMBMNMBHG'==>GO*,/0)¾*3+)))3>q^\nmbhgh_\hg\k^m^ lmkn\mnk^l3

23 < HHD%G'=^lb`g^kl`nb]^mh>G*22*¾-:\mbhglhglmkn\mnk^l'Pbg]Z\mbhgl'MahfZl Mê_hk]%Ehg]hg%+))0'

24 = G*22*¾*¾-¾Pbg]Z\mbhgl'=

25 ; KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22*¾*¾-3>nkh\h]^*':\mbhglhglmkn\mnk^l' @^g^kZeZ\mbhgl'Pbg]Z\mbhgl';LB%+)).' 25a GZmbhgZe:gg^qmh>nkh\h]^*¾IZkm*¾-';LB%+))1'

26 ; KHHD>K%H'<+^]bmbhg"'<

27 M A>M>LHMR'M^\agb\ZeKîhkm/-%@nb]^mhma^]^lb`gZg]\hglmkn\mbhgh_K< _eZmleZ[l%<

28 @ HH=;LM>K%KF'K<lik^Z]la^^mlo,%<

29 BKPBG%:P'=^lb`gh_la^ZkpZee[nbe]bg`l%KîhkmK*)+'

30 M A>M><>GMK>'Phkd^]^qZfie^lmh>nkh\h]^+%Ohenf^+'<

31 F HL>E>R%;%;NG@>R%CANEL>%K'K^bg_hk\^]\hg\k^m^]^lb`gmh>nkh\h]^+%Lbqma >]bmbhg'IZe`kZo^F\FbeeZg%+))0'

32 M A>M>LHMR'=^_e^\mbhglbg\hg\k^m^leZ[lZg][^Zfl'MK.1'Ma^

33 ; >>;R%:'Fh]b_b^]ikhihlZel_hk\hgmkheebg`]^_e^\mbhgl[rf^Zglh_kZmbhlh_liZgmh^__^\mbo^ ]îma%M^\agb\ZeKîhkm-./%<^f^gmZg]

34 :EE>G%:A'K^bg_hk\^]\hg\k^m^]^lb`gmh;L1**)lbfier^qieZbg^]'Lihg%Ehg]hg%*211'

35 BGLMBMNMBHGH?LMKNG@BG>>KL'FZgnZe_hkma^]^lb`gh_\hg\k^m^[nbe]bg` lmkn\mnk^lmh>nkh\h]^+'BLmkn\m>%+))/'

Further reading

184

N

>>;R:PG:K:R:G:GKL'=^lb`g^kl`nb]^mhma^>nkh\h]^l¾>G*22+¾*¾* ; Zg]>G*22+¾*¾+>nkh\h]^+3=^lb`gh_\hg\k^m^lmkn\mnk^l'@^g^kZekne^lZg]kne^l_hk [nbe]bg`lZg]lmkn\mnkZe_bk^]^lb`g'MahfZlMê_hk]%+)).'

N

KBMBLALM:G=:K=LBGLMBMNMBHG'II*22)3+))0'Lmkn\mnkZe>nkh\h]^l%>qmkZ\ml_khf ; ma^lmkn\mnkZe>nkh\h]^l_hklmn]^gmlh_lmkn\mnkZe]^lb`g%l^\hg]^]bmbhg';LB%Ehg]hg% +))0'

N

>G=R<KLFBMA=:'%=^lb`g^kl`nb]^mhma^>nkh\h]^l¾>G*22+¾+>nkh\h]^+3 A =^lb`gh_\hg\k^m^lmkn\mnk^l'IZkm+3

N

M A>M>LHMR'M^\agb\ZeKîhkm/-%@nb]^mhma^]^lb`gZg]\hglmkn\mbhgh_K< _eZmleZ[l%<
:ii^g]bq:3=^kbo^]_hkfneZ^

Appendix A: Derived formulae A1 Flexure: beams and slabs A1.1 Singly reinforced sections Ma^k^\mZg`neZklmk^ll[eh\dlahpg[êhpbg?b`nk^:*fZr[^nl^]' d2


x

nfcd

ec esc

As2

lx

neutral axis

h d

Fc

Fsc z

As

Fst

es a) Section

b) Strain

Fig. 3.5

c) Forces

Figure A1 Strains and forces in a section

?hk`kZ]^lh_\hg\k^m^nimh<.)(/)%e\n6)')),.%n6*Zg]l6)'1 _\]6a\\ _\d (g<6)'1._\d (*'. _r]6_rd (gL6_rd (*'*.6)'10_rd

3.1.6(1), 2.4.2.4(1) & NA 2.4.2.4(1) & NA

?hklbgèrk^bg_hk\^]l^\mbhgl%ma^]^lb`g^jnZmbhgl\Zg[^]^kbo^]Zl_heehpl3 Lever arm, z 0.8x

Fc

z = d – 0.4x Fst

Figure A2 Beam lever arm

?\6!)'1._\d (*'."[!)'1q"6)'-.,_\d[q ?lm6)'10:l _rd
q6 +'.!]¾s"

F

6 )'-.,_\d[+'.!]¾s"s

6 *'*,,,!_\d[s]¾_\d[s+"

E^mD 6 F([] +_\d

6 *'*,,,!_\d[s]¾_\d[s+"([]+_\d

6 *'*,,,!s]¾s+"(] +

=) 6 *'*,,,T!s(]"+¾!s(]"V$D

6 !s(]"+¾!s(]"$)'11+,.D

‡BgikZ\mb\^ma^]^lb`gfhf^gm%F

>]phne][^nl^]'

185

Lheobg`ma^jnZ]kZmb\^jnZmbhg3 s(]6T*$!*¾,'.+2D")'.V(+ s6]T*$T*¾,'.+2D")'.V(+

Table C5

Bmbl\hglb]^k^]`hh]ikZ\mb\^bgma^NDmhebfbms(]mhZfZqbfnfh_)'2.]'!Mabl`nZk]lZ`Zbglm kêrbg` hg o^kr mabg l^\mbhgl h_ \hg\k^m^ pab\a Zm ma^ ^qmk^f^ mhi h_ Z l^\mbhg fZr [^ h_ jn^lmbhgZ[e^lmk^g`ma'"MZ[e^l`bobgòZen^lh_s(]Zg]q(]_hkoZen^lh_DfZr[^nl^]' Area of reinforcement, As MZdbg`fhf^gmlZ[hnmma^\^gmk^h_ma^\hfik^llbhg_hk\^3 F6)'10:l _rds


:l6F(!)'10_rd s" Limiting value of relative flexural compressive stress, K' :llnfbg` gh k^]blmkb[nmbhg mZd^l ieZ\^% Z ebfbmbg` oZen^ !hg ma^ lmk^g`ma h_ \hg\k^m^ bg \hfik^llbhg"_hkD\Zg[^\Ze\neZm^]!]^ghm^]D "Zl_heehpl' Table 3.1

e\n, 6 \hg\k^m^lmkZbg6)')),. 6 k^bg_hk\^f^gmlmkZbg el 6 .))(!*'*.+))*),"6)'))++ ?khflmkZbg]bZ`kZf%?b`nk^:* q 6 )')),.](!)')),.$)'))++" 6 )'/] ?khf^jnZmbhglZ[ho^3 F 6 )'-.,_\d[qs F 6 )'-.,_\d[)'/]!]¾)'-)'/]" 6 )'+)0_\d[]+ =D 6)'+)0 Bm bl h_m^g \hglb]^k^] `hh] ikZ\mb\^ mh ebfbm ma^ ]îma h_ ma^ g^nmkZe Zqbl mh Zohb] Âho^k& k^bg_hk\^f^gmÃ!b'^'mh^glnk^maZmma^k^bg_hk\^f^gmblrbê]bg`Zm_Zbenk^%manlZohb]bg`[kbmme^ _Zbenk^h_ma^\hg\k^m^"'H_m^gq(]blebfbm^]mh)'-.'Mablblk^_^kk^]mhZlma^[ZeZg\^]l^\mbhg [^\Znl^Zmma^nembfZmêbfbmlmZm^ma^\hg\k^m^Zg]lm^êk^Z\ama^bknembfZm^lmkZbglZmma^ lZf^mbf^T,*V'MablblghmZ>nkh\h]^+k^jnbk^f^gmZg]blghmZ\\îm^][rZee^g`bg^^kl' Ghg^maê^ll_hkq6)'-.] ?khf^jnZmbhglZ[ho^3 F 6 )'-.,_\d[qs F 6 )'-.,_\d[)'-.]!]¾)'-)'-.]" 6 )'*/0_\d[]+ =D 6 )'*/0

Cl. 5.5(4)

q(]blZelhk^lmkb\m^][rma^Zfhngmh_k^]blmkb[nmbhg\Zkkb^]hnm'?hk_\d©.)FIZ dª)'-$!)'/$)'))*-e\n"qn(] pa^k^ ] 6 k^]blmkb[nm^]fhf^gm(êZlmb\[^g]bg`fhf^gm[^_hk^k^]blmkb[nmbhg qn 6 ]îmah_ma^g^nmkZeZqblZmNELZ_m^kk^]blmkb[nmbhg e\n 6 \hfik^llbo^lmkZbgbgma^\hg\k^m^ZmNEL Mabl`bo^lmaôZen^lbgMZ[e^:*'

186

:ii^g]bq:3=^kbo^]_hkfneZ^ Table A1 Limits on D with respect to redistribution ratio, d d

1

0.95

0.9

0.85

0.8

0.75

0.7

% redistribution

)

.

*)

*.

+)

+.

,)

K'

)'+)1

)'*2.

)'*1+

)'*/1

)'*.,

)'*,0

)'*+)

B_D7D ma^l^\mbhglahne][^k^lbs^]hk\hfik^llbhgk^bg_hk\^f^gmblk^jnbk^]'Bgebg^pbma \hglb]^kZmbhg h_ `hh] ikZ\mb\^ hnmebg^] Z[ho^% this publication adopts a maximum value of K'= 0.167'


A1.2 Compression reinforcement, As2 Ma^fZchkbmrh_[^Zflnl^]bgikZ\mb\^Zk^lbgèrk^bg_hk\^]%Zg]ma^l^[^Zfl\Zg[^]^lb`g^]nlbg` ma^_hkfneZ]^kbo^]Z[ho^'Bglhf^\Zl^l%\hfik^llbhgk^bg_hk\^f^gmblZ]]^]bghk]^kmh3 N Bg\k^Zl^l^\mbhglmk^g`mapa^k^l^\mbhg]bf^glbhglZk^k^lmkb\m^]%b'^'pa^k^D7D N Mhk^]n\êhg`m^kf]^_e^\mbhg N Mh]^\k^Zl^\nkoZmnk^(]^_hkfZmbhgZmnembfZmêbfbmlmZm^

As2

As Figure A3 Beam with compression reinforcement

Pbmak^_^k^g\^mh?b`nk^:*%ma^k^blghpZg^qmkZ_hk\^ ?l\6)'10:l+ _rd Ma^Zk^Zh_m^glbhgk^bg_hk\^f^gm\Zgghp[^\hglb]^k^]bgmphiZkml%ma^_bklmiZkmmh[ZeZg\^ ma^\hfik^llbo^_hk\^bgma^\hg\k^m^%ma^l^\hg]iZkmmh[ZeZg\^ma^_hk\^bgma^\hfik^llbhg lm^ê'Ma^Zk^Zh_m^glbhgk^bg_hk\^f^gmk^jnbk^]blma^k^_hk^3 :l6D _\n[] +(!)'10_rds"$:l+ pa^k^ sbl\Ze\neZm^]nlbg`D'bglm^Z]h_D :l+\Zg[^\Ze\neZm^][rmZdbg`fhf^gmlZ[hnmma^\^gmk^h_ma^m^glbhg_hk\^3 F6F $)'10_rd:l+!]¾]+" F6D _\n[] +$)'10_rd:l+!]¾]+" K^ZkkZg`bg`3 :l+6!D¾D " _\d[] +(T)'10_rd!]¾]+"V

A2 Shear A2.1 Shear resistance (without shear reinforcement), VRd,c OK]%\6T
Exp. (6.2)

pa^k^
NA

d

6 *$!+))(]")'.©+')

187

r* 6 :l (![p]"©)')+

d*

6 )'*.

s\i 6 )_hkghg&ik^lmk^ll^]\hg\k^m^

ofbg 6 )'),.d*'._\d)'.

=OK]%\6)'*+d!*))r*_\d"*(,[p]ª)'),.d*'._\d)'.[p]

A2.2 Shear capacity Ma^\ZiZ\bmrh_Z\hg\k^m^l^\mbhgpbmao^kmb\Zela^Zkk^bg_hk\^f^gmmhZ\m ZlZlmknm%OK]%fZq3


Exp. (6.9)

Cl. 6.2.3(3) Note 1, Exp. (6.6N) & NA

OK]%fZq6a\p[pSv* _\] (!\hmy$mZgy" pa^k^ a\p 6 *') v* 6 v6)'/T*¾_\d (+.)V _\] 6 a\\ _\d (g<6*'))_\d (*'. =OK]%fZq6)'-)[ps_\dT*¾_\d (+.)V(!\hmy$mZgy" K^ZkkZg`bg`mabl^jnZmbhg`bo^l3 y6)'.lbg¾*To>]s (!)'+)_\dT*¾_\d (+.)V"Vª\hm¾*+'. pa^k^ o>]s6O>] ([s6O>] (![)'2]" Bgfhlm\Zl^l%pa^k^\hmy6+'.%y6+*'1 oK]%fZq%\hmy6+'.6)'*,1[ps_\dT*¾_\d (+.)V hk oK]%fZq%\hmy6+'.6)'*,1_\dT*¾_\d (+.)V pa^k^ oK]%fZq%\hmy6+'. 6OK]%fZq%\hmy6+'.(![s" 6OK]%fZq%\hmy6+'.(!)'2[]" Pa^k^\hmy7+'.%ma^Zgè^h_ma^lmknmZg]oK]%fZqlahne][^\Ze\neZm^]%hkoK]%fZqfZr[^ ehhd^]nibgmZ[e^lhk\aZkml!^'`'MZ[e^<0hk?b`nk^<*"'

A2.3 Shear reinforcement Exp. (6.13)

OK]%l6!:lp(l"s_rp]!\hmy$\hma"lbgaªO>] pa^k^ :lp 6 l 6 s 6 _rp] 6 a 6

\khll&l^\mbhgZeZk^Zh_ma^la^Zkk^bg_hk\^f^gm liZ\bg` eô^kZkf!ZiikhqbfZmôZen^h_)'2]fZrghkfZeer[^nl^]" _rpd (gL6]^lb`grbê]lmk^g`mah_ma^la^Zkk^bg_hk\^f^gm Zgè^h_maêbgdlmhmaêhg`bmn]bgZeZqbl'?hko^kmb\Zeebgdl% \hma6)Zg]lbga6*')

K^ZkkZg`bg`_hko^kmb\Zeebgdl3 :lp(lªO>] (s_rp]\hmy hk :lp(lªo>]%s[p(_rp]\hmy

Exp. (9.5N) & NA

FbgbfnfZk^Zh_la^Zkk^bg_hk\^f^gm :lp%fbg (!l[plbga"ª)')1_\d)'.(_rd pa^k^ l 6 ehg`bmn]bgZeliZ\bg`h_ma^la^Zkk^bg_hk\^f^gm [p 6 [k^Z]mah_ma^p^[

188

:ii^g]bq:3=^kbo^]_hkfneZ^ a 6 Zgè^h_ma^la^Zkk^bg_hk\^f^gmmhmaêhg`bmn]bgZeZqblh_ma^f^f[^k'?hko^kmb\Ze ebgdllbga6*')' K^ZkkZg`bg`_hko^kmb\Zeebgdl3 Alp%fbg (lª)')1[plbga_\d)'.(_rd

A3 Columns


el\

_\]6a\\n_\d(g< sl\ ] + :

e\n+

l+

]\

q a

g'Zqbl er

:l*

slm

e\ a) Strain diagram

Fig. 6.1

]+

b) Stress diagram

Figure A4 Section in axial compression and bending

?hkZqbZeehZ] G>]6_\] []\$:l+sl\¾:l*slm ;nmZl:l+6:l*6:lG(+ G>]6_\] []\$:lG!sl\¾slm"(+ G>]¾_\] []\6:lG!sl\¾slm"(+ !G>]¾_\] []\"(!sl\¾slm"6:lG(+ :lG(+6!G>]¾_\] []\"(!sl\¾slm" =:lG(+6!G>]¾a\\n_\d[]\ (g<"(!sl\¾slm" ?hkfhf^gmZ[hnm\^gmk^h_\henfg F>]6_\] []\!a(+¾]\ (+"$:l+sl\!a(+¾]+"$:l*slm!a(+¾]+" ;nmZl:l+6:l*6:lF(+ F>]6_\] []\!a(+¾]\ (+"$:lF!sl\$slm"!a(+¾]+"(+ F>]¾_\] []\!a(+¾]\ (+"6:lF!sl\$slm"!a(+¾]+"(+ TF>]¾_\] []\!a(+¾]\ (+"V(!sl\$slm"!a(+¾]+"6:lF(+ =:lF(+6TF>]¾a\\n_\d []\!a(+¾]\ (+"(g
?hkl^\mbhglpaheerbg\hfik^llbhg%ma^lmkZbgblebfbm^]ln\amaZmZo^kZ`^lmkZbg ≤e\l6)'))*0.!Zllnfbg`[bebg^Zklmk^ll¾lmkZbgkêZmbhglabi"'

Cl. 6.1(6), Fig. 6.1, Table 3.1

189

Appendix B: Serviceability limit state B1 Deflection BgfZgr\Zl^l%iZkmb\neZkerpbmaleZ[l%]^_e^\mbhgbl\kbmb\Zemh]^lb`g'


>nkh\h]^+%
B1.1 TCC method[5,19] Ma^bg&l^kob\^lmk^llh_k^bg_hk\^f^gm%sl%blnl^]mh]^m^kfbg^Z_Z\mhk%,*)(sl %pab\ablnl^] mhfh]b_rma^[Zlb\liZg 3 ^__^\mbo^]îmakZmbhZlZeehp^]bgnkh\h]^+T+VZg] fh]^kZm^][rma^GZmbhgZe:gg^qT+ZV'Mablf^mah]%abàebàm^]Zl_Z\mhk?,bgnkh\h]^ +T.V% bl bgm^g]^] mh [^ nl^] bg aZg] \Ze\neZmbhgl mh ]^kbo^ !\hgl^koZmbo^" oZen^l h_ sl _khf ZoZbeZ[e^NELfhf^gml'BgZ\\hk]Zg\^pbmaGhm^.h_MZ[e^G:'.h_ma^NDG:T+ZV%ma^kZmbh_hk :l%ikho (:l%k^jblk^lmkb\m^]mh*'.3bg^__^\mmablebfbmlma^_Z\mhk,*)(slmh*'.' pa^k^‡ sl6!_rd (gL"!pji (pnem"!:l%k^j (:l%ikho"(d©,*)(*'.

pa^k^ _rd 6 \aZkZ\m^kblmb\lmk^g`mah_k^bg_hk\^f^gm6.))FIZ gL 6 iZkmbZe_Z\mhk_hkk^bg_hk\^f^gm6*'*. pji 6 jnZlb&i^kfZg^gmehZ]!N=EZllnf^]" pi^kf6 nembfZmêhZ]!N=EZllnf^]" :l%k^j 6 Zk^Zh_k^bg_hk\^f^gmk^jnbk^] :l%ikho6 Zk^Zh_k^bg_hk\^f^gmikhob]^] d

6 k^]blmkb[nmbhgkZmbh

B1.2 RC Spreadsheets method[28] Ma^K<lik^Z]la^^mlM<nkh\h]^ +T+V Zg] ma^ \nkk^gm GZmbhgZe :gg^qT+ZV%mhfh]b_rma^[Zlb\liZg 3 ^__^\mbo^]îmakZmbh' Pabelm mabl f^mah] `bo^l Z fhk^ Z\\nkZm^ Zg] e^ll \hgl^koZmbo^ Zll^llf^gm h_ sl% bm bl hger lnbmZ[e^_hk\hfinm^klik^Z]la^^mZiieb\Zmbhgl'L^^Zelh:ii^g]bq;.' Bgma^ZgZerlblh_leZ[lZg][^Zfl%lniihkmlZk^nlnZeerZllnf^]mh[îbgg^]'Bgk^Zebmrlniihkml aZo^ lhf^ \hgmbgnbmr% ^li^\bZeer Zm ^g] lniihkml' NlnZeer% ghfbgZe mhi lm^ê bl Zllnf^] Zg] ikhob]^]bgma^mhih_liZglZg]blnl^]bgma^]^m^kfbgZmbhgh_l^\mbhgikhi^kmb^l'

B1.3 Rigorous analysis Kb`hkhnlZgZerlbl%ln\aZlmaZmnl^]bgma^l^kb^lh_K<Lik^Z]la^^mlM<nkh\h]^+%
190

:ii^g]bq;3L^kob\^Z[bebmrebfbmlmZm^ Bg ma^ lik^Z]la^^ml% l^\mbhgl Zm *(+)ma ihbgml Zehg` ma^ e^g`ma h_ Z liZg Zk^ \a^\d^] mh ]^m^kfbg^pa^ma^kma^_e^qnkZem^glbe^lmk^llbgma^l^\mbhgblebdêrmh^q\^^]ma^m^glbe^lmk^g`ma h_ma^\hg\k^m^]nkbg`^bma^k\hglmkn\mbhghkl^kob\êb_^3lîZkZm^ZgZerl^lZk^ng]^kmZd^gnlbg` _k^jn^gmehZ]l%jnZlb&i^kfZg^gmZg]m^fihkZkrehZ]l'B_ma^_e^qnkZem^glbe^lmk^g`mabl^q\^^]^] ng]^k_k^jn^gmehZ]l%ma^gma^l^\mbhgblZllnf^]mh[^\kZ\d^]Zg]k^fZbg\kZ\d^]3\kZ\d^] l^\mbhg ikhi^kmb^l Zk^ nl^] mh ]^m^kfbg^ ma^ kZ]bnl h_ \nkoZmnk^ _hk maZm *(+)ma h_ liZg' B_ _e^qnkZem^glbe^lmk^g`mablghm^q\^^]^]%ng&\kZ\d^]l^\mbhgikhi^kmb^lZk^nl^]' KZ]bbh_\nkoZmnk^Zk^\Ze\neZm^]_hk^Z\a*(+)maliZgbg\k^f^gmh_ma^ê^f^gmnlbg`ma^kêôZgm ikhi^kmb^lZg]fhf^gml]^kbo^]_khfZgZerlblh_jnZlb&i^kfZg^gmZ\mbhgl'=^_hkfZmbhgbl\Ze\neZm^] _khfma^bg\k^f^gmlÃ\nkoZmnk^lobZgnf^kb\Zebgm^`kZmbhgho^kmaê^g`mah_^Z\aliZg'


Ma^f^mah]blbgZ\\hk]Zg\^pbmaMa^
B1.4 Differing results =nkbg`+))1%bm[^\Zf^bg\k^ZlbgèrZiiZk^gmmaZmma^k^Zk^bg\hglblm^g\b^l[^mp^^gma^k^lneml `bo^g [r ma^ kb`hkhnl \Ze\neZmbhg f^mah] Zg] liZg3]îma f^mah]l ]^l\kb[^] bg >nkh\h]^ +' Nlbg` ma^ kb`hkhnl f^mah] `bo^l ]^_e^\mbhgl maZm Zk^ `k^Zm^k maZg phne] [^ ^qi^\m^] _khf ma^ZllnfimbhgllmZm^]_hkE(]f^mah]lb'^']^_e^\mbhgebfbmlh_E(+.)ho^kZee!l^^nkh\h]^+%jnZlb&i^kfZg^gmehZ]lZk^\Zee^]_hk' >g]liZglZk^nlnZeer\kbmb\Ze'Pbmak^li^\mmhma^kb`hkhnlZgZerlblf^mah]%bmaZl[^^gln``^lm^]maZm _hk^g]&liZgl%ma^M<<Zg]K<&lik^Z]la^^mf^mah]lk^lnembg]^_e^\mbhgl\ehl^mhmaêbfbmllmZm^] bg>nkh\h]^+%ikhob]^]maZmZghfbgZe^g]&lniihkmk^lmkZbgbg`fhf^gmblik^l^gmpa^k^ghg^bl Zllnf^]bgZgZerlbl'G*22+¾*¾+lmbineZm^lmaZm+.h_^g]liZg fhf^gmlahne][^nl^]mh]^m^kfbg^^g]lniihkmk^bg_hk\^f^gm'MablblnlnZeerZ\\hffh]Zm^] [rikhob]bg`+.h_^g]liZg[hmmhflm^êZlmhilm^êZm^g]lniihkml'Bmblhgmabl[ZlblmaZm ma^\Ze\neZmbhglbgmablin[eb\ZmbhgZk^\hglb]^k^]Zl[^bg`_nkma^kln[lmZgmbZm^]'

B1.5 Note regarding factor 310/ss (factor F3) :mma^mbf^h_in[eb\Zmbhg!=^\^f[^k+))2"ma^Znmahklp^k^ZpZk^h_Zikh[Z[e^\aZg`^mh NDG:T+ZVMZ[e^G:'.pab\a%bg^__^\m%phne]f^ZgmaZmma^_Z\mhk,*)(sl!?,"6:l%ikho(:l%k^j ≤ *'.% manl ]blZeehpbg` ma^ Z\\nkZm^ f^mah] hnmebg^] bg L^\mbhgl ,'*% ,'+% ,',% ,'-% -', Zg] :ii^g]b\^l;*'*%;*'+Zg]<0'

B2 Neutral axis at SLS Mh_bg]q%g^nmkZeZqbl%Zg]l^kob\^llmk^ll^ls\Zg]sl_hkZ\hg\k^m^l^\mbhg%ZmLEL%\hglb]^kma^ \kZ\d^]l^\mbhgbg?b`nk^;*

191

Relative modulus E/Ec ae – 1

As2

d2 x

1

ae

d

As


Where ae = modular ratio Es/Ec

Figure B1 Cracked concrete section at SLS

?khf_bklmikbg\bie^l%_hkZ_neer\kZ\d^]mkZgl_hkf^]l^\mbhg% MhmZeZk^Zh_l^\mbhg%:6[q$:la^$:l+!a^*" *lmfhf^gmh_Zk^Z%:r6[q+(+$:l]a^$:l+]+!a^*" ?hkZleZ[%[6*)))%ma^k^_hk^ : 6*)))q$:la^$:l+!a^*" :r6.))q+$:l]a^$:l+]+!a^*" G^nmkZeZqbl]îma%q q 6 :r (: 6 T.))q+$:l]a^$:l+]+!a^*"V(T*)))q$:la^$:l+!a^*"V Ma^k^_hk^ qT*)))q$:la^$:l+!a^*"V6T.))q+$:l]a^$:l+]+!a^*"V )

6T.))q+$:l]a^$:l+]+!a^*"VqT*)))q$:la^$:l+!a^*"V

6.))q+qT*)))qV$:l]a^$:l+]+!a^*"VqT:la^$:l+!a^*"V

6.))q+qT:la^$:l+!a^*"V$T:l]a^$:l+]+!a^*"V

Lheobg`ma^jnZ]kZmb\ q6[¨[+-a\")'.V(+Z q 6

T:la^$:l+!a^*"¨tT:la^$:l+!a^*"V+$-.))T:l]a^$:l+]+!a^*"Vv)'.V !+q.))"

hkmkZglihlbg`% T¾!a^*":l+a^:l$tT!a^*":l+$a^:lV+$+)))T!a^*":l+]+$a^:l]Vv)'.V

q6

*)))

hk q6

T!a^*":l+a^:l$tT!a^*":l+$a^:lV+$+[T!a^*":l+]+$a^:l]Vv)'.V [

Mabl^qik^llbhgblnl^]bgma^K<lik^Z]la^^mlT+1V'

192

:ii^g]bq;3L^kob\^Z[bebmrebfbmlmZm^ B3 SLS stresses in concrete, sc, and reinforcement, ss B3.1 Singly reinforced section
x/3 x

Mqp


z As

Fs

a) Section

b) Dimensions and forces

Figure B2 SLS stresses: singly reinforced section

B3.2 Doubly reinforced section
E/Ec = ae – 1 s = sc(ae – 1)(x – d2)/x

E/Ec = ae s = sc d2

b As2

x Mqp

d

As

a) Section

E/Ec = ae s = ss b) Dimensions, modular ratios and stresses

Figure B3 SLS stresses

Appendix C: Design aids Ma^ _heehpbg` mZ[e^l% m^qm Zg] _b`nk^l aZo^ [^^g ]^kbo^] _khf >nkh\h]^ + Zg] Zk^ ikhob]^] Zl]^lb`gZb]l_hk]^lb`g^klbgma^ND'Ma^l^]^lb`gZb]laZo^[^^gk^_^k^g\^]bgma^m^qmZg] `^g^kZeeraZo^[^^gmZd^g_khfL^\mbhg*.h_nkh\h]^+T.V'

C1 Design values of actions ?hkma^NELh_lmk^g`ma!LMK"pa^k^ma^k^blZlbgèôZkbZ[e^Z\mbhgnl^^bma^k3 >qi'!/'*)"_khf;L>G*22)T*)V hkma^phkl^\Zl^h_

N *',.@d$*'.Jd


N *',.@d$c)*'.Jd >qi'!/'*)Z"

Zg] N *'+.@d$*'.Jd

>qi'!/'*)[" pa^k^c)6*')_hklmhkZ`^%)'._hklghp[nmhma^kpbl^)'0%l^^MZ[e^+'+'

Bg fhlm \Zl^l >qi' !/'*)[" pbee [^ ZiikhikbZm^% ^q\îm _hk lmhkZ`^ pa^k^ ma^ nl^ h_ >qi' !/'*)Z" blebdêrmh[^fhk^hg^khnl' ?hkma^LELh_]^_hkfZmbhg%jnZlb&i^kfZg^gmehZ]llahne][^Ziieb^]'Ma^l^Zk^*')@d$c+Jd pa^k^c+bl]î^g]^gmhgnl^%^'`')',_hkh__b\^lZg]k^lb]^gmbZeZg])'0_hklmhkZ`^'

C2 Values of actions MaôZen^lh_Z\mbhgl!b'^'ehZ]l"Zk^]^_bg^]bg>nkh\h]^*T**V'MaîZkmlh_>nkh\h]^*Zk^`bo^g bgMZ[e^<*'Ma^lôZen^lZk^mZd^gZl\aZkZ\m^kblmb\oZen^l':mma^mbf^h_in[eb\Zmbhg%ma^ND GZmbhgZe:gg^q^lmhma^lîZkmlZk^bgoZkbhnllmZm^lh_k^Z]bg^ll' :lI=//10T/VfZd^l\e^Zk%ngmbema^ZiikhikbZm^>nkhi^ZglmZg]Zk]l[^\hf^ZoZbeZ[e^%]^lb`g^kl fZr\hglb]^knlbg`\nkk^gmikZ\mb\^hk\nkk^gm;kbmblaLmZg]Zk]lbg\hgcng\mbhgpbma>nkh\h]^+% ikhob]^]ma^rZk^\hfiZmb[e^pbma>nkh\h]^+Zg]maZmma^k^lnembg`kêbZ[bebmrblZ\\îmZ[e^' ;L>G*22*¾*¾*lmZm^lmaZmma^]^glbmrh_\hg\k^m^bl+-dG(f,%k^bg_hk\^]\hg\k^m^%+.dG(f, Zg]p^mk^bg_hk\^]\hg\k^m^%+/dG(f,' Table C1 The parts of Eurocode 1[11]

194

Reference

Title

BS EN 1991-1-1

=^glbmb^l%lê_&p^bàmZg]bfihl^]ehZ]l

BS EN 1991-1-2

:\mbhglhglmkn\mnk^l^qihl^]mh_bk^

BS EN 1991-1-3

LghpehZ]l

BS EN 1991-1-4

Pbg]Z\mbhgl

BS EN 1991-1-5

Ma^kfZeZ\mbhgl

BS EN 1991-1-6

:\mbhgl]nkbg`^q^\nmbhg

BS EN 1991-1-7

:\\b]^gmZeZ\mbhgl]n^mhbfiZ\mZg]^qiehlbhgl

BS EN 1991-2

MkZ__b\ehZ]lhg[kb]`^l

BS EN 1991-3

:\mbhglbg]n\^][r\kZg^lZg]fZ\abg^kr

BS EN 1991-4

:\mbhglbglbehlZg]mZgdl

:ii^g]bq<3=^lb`gZb]l C3 Analysis :gZerlbl bl ]^Zem pbma bg L^\mbhg . h_ nkh\h]^+'Pa^k^ ZiikhikbZm^ ma^ \h^__b\b^gml `bo^gbgMZ[e^l<+Zg]<,\Zg[^nl^]mh]^m^kfbg^]^lb`gfhf^gmlZg]la^Zk_hkleZ[lZg] [^ZflZmNEL' Table C2 Coefficients for use with one-way spanning slabs to Eurocode 2 Coefficient Location


End support/slab connection

Internal supports and spans

Pinned end support

Continuous

Outer support

Near middle of end span

Outer support

Near middle of end span

Moment

)')

)')1/

¾)')-

Shear

)'-)

¿

)'-/

At 1st interior support

At middle of interior spans

At interior supports

)')0.

¾)')1/

)')/,

¾)')/,

¿

)'/)3)'/)

¿

)'.)3)'.)

Notes 1:iieb\Z[e^mhhg^&pZrliZggbg`leZ[lpa^k^ma^Zk^Zh_^Z\a[Zr^q\^^]l,)f+%Jd©*'+.@dZg]jd©. dG(f+%ln[lmZgmbZeerngb_hkfehZ]bg`!Zme^Zlm,liZgl%fbgbfnfliZgª)'1.fZqbfnf!]^lb`g"liZg' 2=^lb`gfhf^gm6\h^__qgqliZg+Zg]]^lb`gla^Zk6\h^__qgqliZgpa^k^gblZN=EpbmaZlbgèôZkbZ[e^ Z\mbhg6g@ `d$cgJjdpa^k^`dZg]jdZk^\aZkZ\m^kblmb\i^kfZg^gmZg]oZkbZ[e^Z\mbhglbgdG(f' 3;Zlbl3Rbê]ebg^]^lb`g!Zllnf^]+)k^]blmkb[nmbhgT0V"

Table C3 Coefficients for use with beams (and one-way spanning slabs) to Eurocode 2 Coefficient

Location Outer support Near middle of end span

At 1st interior At middle of At interior support interior spans supports

Moment `k and jk

+.liZga

¿

)')2-

¿

)')0.

Moment `k

¿

)')2)

¿

)')//

¿

Moment jk

¿

)'*))

¿

)')1/

¿

Shear

)'-.

¿

)'/,3)'..

¿

)'.)3)'.)b

Notes 1?hk[^ZflZg]leZ[l%,hkfhk^liZgl'!Ma^rfZrZelh[^nl^]_hk+&liZg[^Zfl[nmlniihkm fhf^gm\h^__b\b^gm6)'*)/Zg]bgm^kgZela^Zk\h^__b\b^gm6)'/,[hmalb]^l"' 2@^g^kZeerJd©@d%Zg]maêhZ]bg`lahne][^ln[lmZgmbZeerngb_hkfer]blmkb[nm^]'Hma^kpbl^li^\bZe \nkmZbef^gmh_k^bg_hk\^f^gmblk^jnbk^]' 3FbgbfnfliZgª)'1.qfZqbfnf!Zg]]^lb`g"liZg' 4=^lb`gfhf^gmZmlniihkml 6 \h^__qgqliZg+ hkbgliZgl 6 !\h^__`dqg@`d$\h^__jdqcgJjd"qliZg+' 5=^lb`gla^ZkZm\^gmkêbg^h_lniihkml6\h^__qgqliZgpa^k^gblZN=EpbmaZlbgèôZkbZ[e^Z\mbhg 6g@`d$cgJjdpa^k^`dZg]jdZk^\aZkZ\m^kblmb\i^kfZg^gmZg]oZkbZ[e^Z\mbhglbgdG(f' g@Zg]cgJZk^]î^g]^gmhgnl^h_;L>G*22)%>qik^llbhgl!/'*)"%!/'*)Z"hk!/'*)["'L^^L^\mbhg<*' 6;Zlbl3:ee&Zg]Zem^kgZm^&liZgl&ehZ]^]\Zl^lZlNDGZmbhgZe:gg^qZg]*.k^]blmkb[nmbhgZm lniihkml' Key a:mhnm^klniihkmÂ+.liZgÃkêZm^lmhma^NDGZmbhgZeer=^m^kfbg^]IZkZf^m^k_hk>nkh\h]^+% nkh\h]^+%
Cl. 9.2.1.2 Cl. 9.3.1.2

195

C4 Design for bending N =^m^kfbg^pa^ma^kD©D hkghm!b'^'pa^ma^kng]^k&k^bg_hk\^]hkghm"' pa^k^ D 6 F>] (![]+_\d" pa^k^ ] 6 ^__^\mbo^]îma6a¾\ho^k¾f(+ [ 6 pb]mah_l^\mbhgbg\hfik^llbhg D fZr[^]^m^kfbg^]_khfMZ[e^<-Zg]bl]î^g]^gmhgma^k^]blmkb[nmbhgkZmbhnl^]' Table C4 Values for D


Redistribution ratio, d

s/] for D

a

D

a

1–d

1.00

)'0/!)'1+"

)'+)1!)'*/1"

)

0.95

)'01!)'1+"

)'*2.!)'*/1"

.

0.90

)'1)!)'1+"

)'*1+!)'*/1"

*)

0.85

)'1+

)'*/1

*.

0.80

)'1-

)'*.,

+)

0.75

)'1/

)'*,0

+.

0.70

)'11

)'*+)

,)

Note ] (_r]s pa^k^ :l* 6 Zk^Zh_m^glbe^k^bg_hk\^f^gm F>]6 ]^lb`gfhf^gm _r] 6 _rd (gL6.))(*'*.6-,-'1FIZ s 6 ]T)'.$)'.!*¾,'.,D")'.V©)'2.] OZen^lh_s(]!Zg]q(]"fZr[^mZd^g_khfMZ[e^<.

How to: Beams[8]

?hk_eZg`^][^Zflpa^k^q5*'+.a_% :l* 6 F>] (_r]s pa^k^ q 6 ]îmamhg^nmkZeZqbl'OZen^lh_q(]fZr[^mZd^g_khfMZ[e^<. a_ 6 mab\dg^llh__eZg`^

?hk_eZg`^][^Zflpa^k^qª*'+.a_%k^_^kmhAhpmh]^lb`g\hg\k^m^lmkn\mnk^lnlbg`>nkh\h]^+T1V' N B_D7D %l^\mbhgblover-reinforcedZg]k^jnbk^l\hfik^llbhgk^bg_hk\^f^gm' :l+6!F>]¾F "(_l\!]¾]+" pa^k^ :l+6 \hfik^llbhgk^bg_hk\^f^gm B_]+(q7)',0.ma^gma^m^kf:l+lahne][^kîeZ\^][rma^m^kf *'/!*¾]+(q":l+ F 6 D []+_\d _l\ 6 0))!qn¾]+"(qn©_r]

196

pa^k^ ]+ 6 ^__^\mbo^]îmamh\hfik^llbhgk^bg_hk\^f^gm

:ii^g]bq<3=^lb`gZb]l

qn 6 !d¾)'-"]

pa^k^ d 6k^]blmkb[nmbhgkZmbh

MhmZeZk^Zh_lm^ê:l*6F (!_r]s"$:l+_l\ (_r]


Table C5 Values of s/] and q/] for singly reinforced rectangular sections D

s/]

q/]

(1 – d)maxa

0.04

)'2.)b

)'*+.

,)

0.05

)'2.)b

)'*+.

,)

0.06

)'2--

)'*-)

,)

0.07

)'2,-

)'*/.

,)

0.08

)'2+-

)'*2*

,)

0.09

)'2*,

)'+*0

,)

0.10

)'2)+

)'+-.

,)

0.11

)'12*

)'+0+

,)

0.12

)'11)

)',)*

,)

0.13

)'1/1

)',,*

+0

0.14

)'1./

)',/*

+-

0.15

)'1-,

)',2,

+*

0.16

)'1,)

)'-+.

*1

0.17

)'1*/c

)'-/)c

*-

0.18

)'1)+c

)'-2.c

**

0.19

)'010c

)'.,,c

0

0.20

)'00*c

)'.0+c

,

0.208

)'0.1c

)'/)/c

)

Note _\d©.)FIZ Key

aFZqbfnfZeehpZ[e^k^]blmkb[nmbhg bIkZ\mb\Zeebfbm cBmblk^\hff^g]^]maZmq(]blebfbm^]mh)'-.)T,.V':lZ\hgl^jn^g\^s(]blebfbm^]mhZfbgbfnfh_ )'1+)Zg]D mh)'*/1'

C5 Design for beam shear C5.1 Requirement for shear reinforcement B_o>]7oK]%\ma^gla^Zkk^bg_hk\^f^gmblk^jnbk^] pa^k^ o>] 6 O>] ([p]%_hkl^\mbhglpbmahnmla^Zkk^bg_hk\^f^gm!b'^'leZ[l" oK]%\ 6 la^Zkk^lblmZg\^pbmahnmla^Zkk^bg_hk\^f^gm%_khfMZ[e^
197

Table C6 Shear resistance without shear reinforcement, oRd,c (MPa)


rl = :sl/ [w]

Effective depth ] (mm) G 200

225

250

275

300

350

400

450

500

600

750

©0.25%

)'.-

)'.+

)'.)

)'-1

)'-0

)'-.

)'-,

)'-*

)'-)

)',1

)',/

0.50%

)'.2

)'.0

)'./

)'..

)'.-

)'.+

)'.*

)'-2

)'-1

)'-0

)'-.

0.75%

)'/1

)'//

)'/-

)'/,

)'/+

)'.2

)'.1

)'./

)'..

)'.,

)'.*

1.00%

)'0.

)'0+

)'0*

)'/2

)'/1

)'/.

)'/-

)'/+

)'/*

)'.2

)'.0

1.25%

)'1)

)'01

)'0/

)'0-

)'0,

)'0*

)'/2

)'/0

)'//

)'/,

)'/*

1.50%

)'1.

)'1,

)'1*

)'02

)'01

)'0.

)'0,

)'0*

)'0)

)'/0

)'/.

1.75%

)'2)

)'10

)'1.

)'1,

)'1+

)'02

)'00

)'0.

)'0,

)'0*

)'/1

ª 2.00%

)'2-

)'2*

)'12

)'10

)'1.

)'1+

)'1)

)'01

)'00

)'0-

)'0*

Notes 1MZ[e^]^kbo^]_khf>nkh\h]^+Zg]NDGZmbhgZe:gg^q' 2MZ[e^\k^Zm^]_hk_\d6,)FIZZllnfbgò^kmb\Zeebgdl' 3?hkr eª)'-Zg] _\d6+.FIZ%Ziier_Z\mhkh_)'2-

_\d6-)FIZ%Ziier_Z\mhkh_*'*)

_\d6.)FIZ%Ziier_Z\mhkh_*'*2

_\d6,.FIZ%Ziier_Z\mhkh_*').

_\d6-.FIZ%Ziier_Z\mhkh_*'*-

GhmZiieb\Z[e^_hk_\d7.)FIZ

C5.2 Section capacity check B_o>]%s7oK]%fZqma^gl^\mbhglbs^blbgZ]^jnZm^ pa^k^ o>]%s 6 O>] ([ps6O>] ([p)'2]%_hkl^\mbhglpbmala^Zkk^bg_hk\^f^gm oK]%fZq6 \ZiZ\bmrh_\hg\k^m^lmknml^qik^ll^]ZlZlmk^llbgmaô^kmb\ZeieZg^ 6 OK]%fZq ([ps 6 OK]%fZq ([p)'2] oK]%fZq\Zg[^]^m^kfbg^]_khfMZ[e^<0%bgbmbZeer\a^\dbg`Zm\hmy6+'.'Lahne]bm[^k^jnbk^]% Z`k^Zm^kk^lblmZg\^fZr[^Zllnf^][rnlbg`ZeZk`^klmknmZgè^%y' Table C7 Capacity of concrete struts expressed as a stress, oRd,max _ck

oRd,max (MPa) cot y

2.50

2.14

1.73

1.43

1.19

1.00

y

2.18°

25°

30°

35°

40°

45°

20

+'.-

+'1+

,'*2

,'-/

,'/+

,'/1

)'..+

25

,'*)

,'-.

,'2)

-'+,

-'-,

-'.)

)'.-)

30

,'/-

-')-

-'.0

-'2/

.'+)

.'+1

)'.+1

35

-'*.

-'/*

.'+*

.'//

.'2,

/')+

)'.*/

40

-'/,

.'*.

.'1+

/',*

/'/+

/'0+

)'.)-

45

.')2

.'/.

/',2

/'2,

0'+0

0',1

)'-2+

50

.'.+

/'*,

/'2,

0'.+

0'11

1'))

)'-1)

Notes 1MZ[e^]^kbo^]_khf>nkh\h]^+Zg]NDGZmbhgZe:gg^qZllnfbgò^kmb\Zeebgdl%b'^'\hma6) 2v6)'/T*¾!_\d (+.)"V 3oK]%fZq6v_\]!\hmy$\hma"(!*$\hm+y"

198

Strength reduction factor, v

:ii^g]bq<3=^lb`gZb]l C5.3 Shear reinforcement design :lp(lªo>]%s[p(_rp]\hmy pa^k^ :lp 6 Zk^Zh_la^Zkk^bg_hk\^f^gm!o^kmb\ZeebgdlZllnf^]" l 6 liZ\bg`h_la^Zkk^bg_hk\^f^gm o>]%s 6 O>] ([ps%Zl[^_hk^ [p 6 [k^Z]mah_ma^p^[ _rp] 6 _rpd (gL6]^lb`grbê]lmk^g`mah_la^Zkk^bg_hk\^f^gm

:em^kgZmboêr% :lp(l i^k f^mk^ pb]ma h_ [p fZr [^ ]^m^kfbg^] _khf ?b`nk^ <*Z" hk <*[" Zl bg]b\Zm^] [r ma^ [en^ Zkkhpl bg ?b`nk^<*Z"'Ma^l^ _b`nk^l fZr Zelh [^ nl^] mh ^lmbfZm^ ma^ oZen^h_\hmy' ;^ZflZk^ln[c^\mmhZfbgbfnfla^Zkebgdikhoblbhg':llnfbgò^kmb\Zeebgdl% :lp%fbg (l[pª)')1_\d)'.(_rd!l^^MZ[e^<1"' Table C8 Values of :sw,min/l[w for beams for vertical links and _yk = 500 MPa and compatible resistance, oRd Concrete class

C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60

Asw,min/sbw for beams (x 103) )'0+

)'1)

)'11

)'2.

*')*

*')0

*'*,

vRd for Asw,min /sbw (MPa)

)'10

)'2.

*'),

*'*)

*'*0

*'+,

)'01

vRd,max for cot y = 2.5

8.0

2.14

1.73

1.43 C50/60

7.0

1.19 C45/55 C40/50

fywk = 500 MPa

1.00

C35/45

6.0 C30/37 5.0 vEd,z (MPa)


@^g^kZeer:lp(lªo>]%s[p(*)10 pa^k^_rpd6.))FIZ%gL6*'*.Zg]\hmy6+'.

C25/30 4.0

C20/25

See Fig. C1b) 3.0 2.0 1.0 0.0 0

2

4

6 8 10 Asw/s required per metre width of bw

12

14

Figure C1a) Diagram to determine :sw/l required (for beams with high shear stress)

199

4.0

C30/37 0

C25/3

fywk = 500 MPa

C20/25


vEd,z (MPa)

3.0

2.0

Range of vRd,c for range d = 200 mm, r = 2.0% to d = 750 mm, r = 0.5%

C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60

1.0 Asw,min/s for beams

0.0

0

1

2 Asw/s required per metre width of bw

4

3

Figure C1b) Diagram to determine :sw/l required (for slabs and beams with low shear stress)

C6 Design for punching shear =^m^kfbg^ b_ ing\abg` la^Zk k^bg_hk\^f^gm bl k^jnbk^]% bgbmbZeer Zm n*% ma^g b_ g^\^llZkr Zm ln[l^jn^gmi^kbf^m^kl%nb'B_o>]7oK]%\ma^ging\abg`la^Zkk^bg_hk\^f^gmblk^jnbk^] pa^k^ o>] 6 bO>] (nb]

pa^k^ b 6 _Z\mhk]^Zebg`pbma^\\^gmkb\bmr O>] 6 Ziieb^]la^Zk_hk\^ nb 6 e^g`mah_maî^kbf^m^kng]^k\hglb]^kZmbhg ] 6 f^Zg^__^\mbo^]îma oK]%\ 6 la^Zkk^lblmZg\^pbmahnmla^Zkk^bg_hk\^f^gm!l^^MZ[e^
?hko^kmb\Zela^Zkk^bg_hk\^f^gm !:lp(lk"6 n*!o>]¾)'0.oK]%\"(!*'._rp]%^_" pa^k^ :lp 6 Zk^Zh_la^Zkk^bg_hk\^f^gmbghgî^kbf^m^kZkhng]ma^\henfg' ?hk:lp%fbgl^^nkh\h]^+%L^\mbhg*)'-'+Zg]_hkeZrhnml^^L^\mbhg*+'-', lk 6 kZ]bZeliZ\bg`h_i^kbf^m^klh_la^Zkk^bg_hk\^f^gm Concise: 10.4.2, 12.4.3

_rp]%^_

n* 6 [Zlb\\hgmkhei^kbf^m^k+]_khf\henfg_Z\^ 6 ^__^\mbo^]^lb`glmk^g`mah_k^bg_hk\^f^gm6!+.)$)'+.]"©_rp]'?hk@kZ]^ .))la^Zkk^bg_hk\^f^gml^^MZ[e^<2

Table C9 Values of _ywd,ef for grade 500 reinforcement ] fywd,ef

150

200

250

300

350

400

450

+10'.

,))

,*+'.

,+.

,,0'.

,.)

,/+'.

:mma^\henfgi^kbf^m^k%\a^\do>]≤OK]fZq_hk\hmy6*')`bo^gbgMZ[e^<0' 200

:ii^g]bq<3=^lb`gZb]l C7 Check deflection


Bg `^g^kZe% ma^ LEL lmZm^ h_ ]^_e^\mbhg fZr [^ \a^\d^] [r nlbg` ma^ liZg&mh&^__^\mbo^&]îma ZiikhZ\a'Fhk^\kbmb\ZeZiikZblZeh_]^_hkfZmbhgblhnmlb]^ma^l\hi^h_mablin[eb\Zmbhg'Mhnl^ ma^liZg&mh&^__^\mbo^&]îmaZiikhZ\a%o^kb_rmaZm3 :eehpZ[eê(]6GqDq?*q?+q?,ªZ\mnZee(] pa^k^ G 6 [Zlb\liZg&mh&^__^\mbo^&]îmakZmbh]^kbo^]_hkD6*')Zg]r 6)_khfL^\mbhg*)'.'+ h_nkh\h]^+hkMZ[e^<*)hk?b`nk^<+ D 6 _Z\mhkmhZ\\hngm_hklmkn\mnkZelrlm^f'L^^MZ[e^<** ?*6 _Z\mhkmhZ\\hngm_hk_eZg`^]l^\mbhgl'Pa^g[^__ ([p6*')%_Z\mhk?*6*')' Pa^g[^__([pbl`k^Zm^kmaZg,')%_Z\mhk?*6)'1)' ?hkoZen^lh_[^__ ([p[^mp^^g*')Zg],')%bgm^kiheZmbhgfZr[^nl^]!l^^MZ[e^<*+" pa^k^ [^__bl]^_bg^]bgL^\mbhg.'+'+h_nkh\h]^+ [p 6 pb]mah_p^[ BgB[^Zfl[p6fbgbfnfpb]mah_p^[bgm^glbe^Zk^Z' BgmZi^k^]p^[l[p6pb]mah_p^[Zm\^gmkhb]h_k^bg_hk\^f^gmbgp^[' ?+6 _Z\mhkmhZ\\hngm_hk[kbmmeîZkmbmbhglbgZllh\bZmbhgpbmaehg`liZgl'@^g^kZeer?+ 6*')[nmb_[kbmmeîZkmbmbhglZkêbZ[e^mh[^]ZfZ`^][r^q\^llbo^]^_e^\mbhg%?+ lahne][^]^m^kfbg^]Zl_heehpl3 Z"bg_eZmleZ[lbgpab\amaêhg`^kliZgbl`k^Zm^kmaZg1'.f%?+61'.(e^__ ["bg[^ZflZg]hma^kleZ[lpbmaliZglbg^q\^llh_0')f%?+60')(e^__ OZen^lh_?+fZr[^mZd^g_khfMZ[e^<*, ?,6 _Z\mhkmhZ\\hngm_hkl^kob\^lmk^llbgm^glbe^k^bg_hk\^f^gm6,*)(sl©*'.

Concise: 10.5.2

Concise: 5.2.2

Fhk^Z\\nkZmêr%‡ma^l^kob\^Z[bebmrlmk^ll%sl%fZr[^^lmbfZm^]Zl_heehpl3 sl6_rd (gLT!@d$c+ Jd"(!*'+.@d$*'.Jd"VT:l%k^j (:l%ikhoV!*(d" hk sl6slnT:l%k^j (:l%ikhoV!*(d" pa^k^ sln

6 ma^ ngfh]b_b^] LEL lm^ê lmk^ll% mZdbg` Z\\hngm h_ gF _hk k^bg_hk\^f^gmZg]h_`hbg`_khfnembfZm^Z\mbhglmhl^kob\^Z[bebmr Z\mbhgl 6 .))(gL!@d$c+ Jd"(!*'+.@d$*'.Jd" slnfZr[^^lmbfZm^]_khf?b`nk^<,Zlbg]b\Zm^][rma^[en^ Zkkhp :l%k^j (:l%ikho 6 Zk^Zh_lm^êk^jnbk^]]bob]^][rZk^Zh_lm^êikhob]^]' !*(d" 6 _Z\mhkmhÂng&k^]blmkb[nm^ÃNELfhf^gmllhma^rfZr[^nl^]bg mablLELo^kb_b\Zmbhg!l^^MZ[e^<*-"

:\mnZee(]6Z\mnZeliZg]bob]^][r^__^\mbo^]îma%]'

‡L^^:ii^g]bq;*'. 201

Table C10 Basic ratios of span-to-effective-depth, G, for members without axial compression Required reinforcement, r

_ck 20

25

30

35

40

45

0.30%

+.'2

,+'+

,2'+

-/'/

.-'/

/,')

0*'1

0.40%

*2'*

++'-

+/'+

,)'-

,.')

,2'1

-.')

50

0.50%

*0')

*1'.

+)'.

+,')

+.'1

+1'1

,+')

0.60%

*/')

*0',

*1'.

*2'1

+*',

+,'*

+.'+

0.70%

*.',

*/'-

*0'-

*1'.

*2'/

+)'/

+*'0

0.80%

*-'1

*.'0

*/'/

*0'/

*1'.

*2'-

+)'-

0.90%

*-',

*.'+

*/')

*/'1

*0'0

*1'.

*2',

1.00%

*-')

*-'1

*.'.

*/',

*0')

*0'1

*1'.

1.20%

*,'.

*-'*

*-'1

*.'-

*/')

*/'/

*0',

1.40%

*,'*

*,'0

*-'+

*-'1

*.',

*.'1

*/'-

1.60%

*+'2

*,',

*,'1

*-',

*-'1

*.'+

*.'0

1.80%

*+'0

*,'*

*,'.

*,'2

*-',

*-'1

*.'+

2.00%

*+'.

*+'2

*,',

*,'/

*-')

*-'-

*-'1

2.50%

*+'+

*+'.

*+'1

*,'*

*,'-

*,'0

*-')

3.00%

*+')

*+',

*+'.

*+'1

*,')

*,',

*,'.

3.50%

**'2

*+'*

*+',

*+'.

*+'0

*+'2

*,'*

4.00%

**'1

**'2

*+'*

*+',

*+'.

*+'0

*+'2

4.50%

**'0

**'1

*+')

*+'+

*+',

*+'.

*+'0

5.00%

**'/

**'1

**'2

*+'*

*+'+

*+'-

*+'.

)'.)

)'..

)'.2

)'/,

)'/0

)'0*

)'-. Reference reinforcement ratio,r0

Notes 1Pa^k^r6:l ([]' 2?hkM&l^\mbhglrblma^Zk^Zh_k^bg_hk\^f^gm]bob]^][rma^Zk^Zh_\hg\k^m^Z[ho^ma^\^gmkhb]h_ ma^m^glbhgk^bg_hk\^f^gm' 3MaôZen^l_hkliZg&mh&^__^\mbo^&]îmaaZo^[^^g[Zl^]hgMZ[e^0'-Gbg>nkh\h]^+%nlbg`D6* !lbfierlniihkm^]"Zg]r 6)!gh\hfik^llbhgk^bg_hk\^f^gmk^jnbk^]"' 4Ma^liZg&mh&^__^\mbo^&]îmakZmbhlahne][^[Zl^]hgma^lahkm^kliZgbgmph&pZrliZggbg`leZ[lZg] maêhg`^kliZgbg_eZmleZ[l'

32 Basic span-to-effective-depth ratio N (l/d)


Table 7.4N

30

fck = 50

28

fck = 45 fck = 40

26

fck = 35

24 fck = 30 22 20 18 16 14 12 0.40%

fck = 25 fck = 20 0.60%

1.40% 1.60% 1.20% 0.80% 1.00% Design tension reinforcement (100As,req /bd)

Figure C2 Basic span-to-effective depth ratios, G, for D = 1, r' = 0

202

1.80% 2.00%

:ii^g]bq<3=^lb`gZb]l Table C11 D factors to be applied to basic ratios of span-to-effective-depth D

Beams

Slabs

Lbfierlniihkm^][^Zfl

Hg^&hkmph&pZrliZggbg`lbfierlniihkm^]leZ[l

*')

>g]liZgh_\hgmbgnhnl[^Zfl

>g]liZgh_hg^&pZrliZggbg`\hgmbgnhnlleZ[l%hk mph&pZrliZggbg`leZ[l\hgmbgnhnlho^khgêhg`^]`^

*',

Bgm^kbhkliZglh_\hgmbgnhnl[^Zfl

Bgm^kbhkliZglh_\hgmbgnhnlleZ[l

*'.

¿

?eZmleZ[l![Zl^]hgehg`^kliZg"

*'+

)'-

Table C12 Factor F1, modifier for flanged beams [eff/[w

1.0

1.5

2.0

2.5

ª3.0

Factor

*'))

)'2.

)'2)

)'1.

)'1)

Table C13 Factor F2, modifier for long spans supporting brittle partitions Span, m

eeff

© 7.0 7.5

8.0

8.5

9.0

10.0

11.0

12.0

13.0

14.0

15.0

16.0

Flat slabs

8.5/eeff

*'))

*'))

*'))

*'))

)'2-

)'1.

)'00

)'0*

)'/.

)'/*

)'.0

)'.,

Beams and other slabs 7.0/eeff

*'))

)'2,

)'11

)'1+

)'01

)'0)

)'/-

)'.1

)'.-

)'.)

)'-0

)'--

320 35

y2 = 0.8, gG = 1.

300 Unmodified steel stress ssu


Structural system

280 y2=

260 240

0.6,

gG

y 2 = 0.6, g G =

25 = 1.

.3, g G

y2 = 0

.25 =1 g G .25 .3, =1 =0 g G y2 .2, =0 y2

1.35

= 1.35 .35

, gG = 1

y 2 = 0.2

220 200 180

1.00

2.00

3.00

4.00

Ratio Gk/Qk Figure C3 Determination of unmodified SLS, stress in reinforcement, ssu

203

Table C14 (1/d) factor to be applied to unmodified ssu to allow for redistribution used Average redistribution used

20%

15%

10%

5%

0%

–5%

–10%

–15%

–20%

–25%

–30%

Redistribution ratio used, d

1.20

1.15

1.10

1.05

1.00

0.95

0.90

0.85

0.80

0.75

0.70

(1/d)

1,

10

2*

2.

*))

*).

***

**1

*+.

*,,

*-,


Notes 1 Pa^k^\h^__b\b^gml_khfMZ[e^<+aZo^[^^gnl^]bg]^lb`gZg]pa^k^Jd&*'+.@d%ma^\h^__b\b^gmlbgMZ[e^<+fZr[^\hglb]^k^]mh kîk^l^gmfhf^gm]blmkb[nmbhgh_3 ¾1g^Zkfb]]e^h_^g]liZgpbmaibgg^]^g]lniihkm ¾++Zm_bklmbgm^kbhklniihkm%ZlZphklm\Zl^ $,g^Zkfb]]e^h_bgm^kgZeliZgl%ZlZphklm\Zl^ ¾+1Zmbgm^kbhklniihkml%ZlZphklm\Zl^' 2 Pa^k^\h^__b\b^gml_khfMZ[e^<,aZo^[^^gnl^]bg]^lb`gZg]pa^k^Jd&@d%ma^\h^__b\b^gmlbgMZ[e^<,fZr[^\hglb]^k^]mhkîk^l^gm fhf^gmk^]blmkb[nmbhgh_3 $,g^Zkfb]]e^h_^g]liZgpbmaibgg^]^g]lniihkm%ZlZphklm\Zl^ $2g^Zkfb]]e^h_bgm^kgZeliZgl%ZlZphklm\Zl^ ¾*.ZmZeebgm^kbhklniihkml'

C8 Control of cracking
Maximum bar size (mm)

Maximum bar spacing (mm)

pk = 0.3 mm

pk = 0.4 mm

pk = 0.3 mm

pk = 0.4 mm

160

,+

-)

,))

,))

200

+.

,+

+.)

,))

240

*/

+)

+))

+.)

280

*+

*/

*.)

+))

320

*)

*+

*))

*.)

360

1

*)

.)

*))

OR

Notes 1Ma^ÂghkfZeÃebfbmh_)',fffZr[^kêZq^]mh)'-ff_hkQHZg]Q<*^qihlnk^\eZll^lb_ma^k^bl ghli^\b_b\k^jnbk^f^gm_hkZii^ZkZg\^' 2MZ[e^Zllnfimbhglbg\en]^\ghf6+.ffZg]_\m%^__!6_\mf"6+'2FIZ'

204

:ii^g]bq<3=^lb`gZb]l C9 Design for axial load and bending C9.1 General Bg\henfgl%]^lb`gfhf^gmlF>]Zg]]^lb`gZiieb^]ZqbZe_hk\^G>]lahne][^]^kbo^]_khfZgZerlbl% \hglb]^kZmbhgh_bfi^k_^\mbhglZg]%pa^k^g^\^llZkr%+g]hk]^k^__^\ml'


Bmblg^\^llZkrmh\Ze\neZm^^__^\mboê^g`malbghk]^kmh]^m^kfbg^pa^ma^kZ\henfgblle^g]^k !l^^>nkh\h]^+%qik^llbhg!.'*.""'Ma^^__^\mboê^g`mah_fhlm\henfglpbee[^ e(+5e)5e!l^^>nkh\h]^+?b`nk^.'0_"'I=//10T/Vnkh\h]^ + !.'1','+!," Zg] .'1','+!."" e^Z]l mh lbfbeZk ^__^\mbo^ e^g`mal mh mahl^ mZ[neZm^] bg ;L 1**)T0V Zl kîkh]n\^] [êhp ZlMZ[e^ <*/' >qi^kb^g\^ ln``^lml maZm ma^l^ mZ[neZm^]oZen^lZk^\hgl^koZmbo^' Table C16 Effective length e0: conservative factors for braced columns End condition at top

End condition at bottom 1

2

3

1

)'0.

)'1)

)'2)

2

)'1)

)'1.

)'2.

3

)'2)

)'2.

*'))

Key
Pa^k^ma^\henfgbl\hgg^\m^]mhZ_hng]Zmbhgmabllahne][^]^lb`g^]mh\Zkkrfhf^gm bghk]^kmhlZmbl_rmabl\hg]bmbhg

nkh\h]^+T,.V'MaôZen^lZk^ mahl^nl^]bg;L1**)3IZkm*3*220T0V_hk[kZ\^]\henfgl'Ma^lôZen^lZk^\ehl^mhmahlôZen^lmaZm phne][^]^kbo^]b_ma^\hgmkb[nmbhg_khfZ]cZ\^gm\henfglp^k^b`ghk^]'

C9.2 Design by calculation :llnfbg`mpheZr^klh_k^bg_hk\^f^gm%:l*Zg]:l+%ma^mhmZeZk^Zh_lm^êk^jnbk^]bgZ\henfg% :l%fZr[^\Ze\neZm^]Zllahpg[êhp' N ?hkZqbZeehZ]

:lG(+6!G>]¾a\\n_\d[]\ (g<"(!sl\¾slm" pa^k^ :lG6mhmZeZk^Zh_k^bg_hk\^f^gmk^jnbk^]mhk^lblmZqbZeehZ]nlbg`mablf^mah]' :lG6:l*$:l+Zg]:l*6:l+ pa^k^ :l*!:l+"6 Zk^Zh_k^bg_hk\^f^gmbgeZr^k*!eZr^k+" G>] 6 ]^lb`gZiieb^]ZqbZe_hk\^ a\\ 6 )'1. n 6 *_hk©<.)(/) [ 6 [k^Z]mah_l^\mbhg ]\ 6 ^__^\mbo^]îmah_\hg\k^m^bg\hfik^llbhg6lq©a

Concise: Fig. 6.3

Concise: Fig. 6.4

205

pa^k^ l 6 q 6 a 6 sl\%!slm" 6

)'1_hk©<.)(/) ]îmamhg^nmkZeZqbl a^bàmh_l^\mbhg lmk^llbg\hfik^llbhg!Zg]m^glbhg"k^bg_hk\^f^gm

N ?hkfhf^gm

:lF(+6TF>]¾a\\n_\d[]\!a(+¾]\ (+"(g

pa^k^ :lF 6 m hmZeZk^Zh_k^bg_hk\^f^gmk^jnbk^]mhk^lblmfhf^gmnlbg`mablf^mah] :lF6:l*$:l+Zg]:l*6:l+ Pa^k^k^bg_hk\^f^gmblghm\hg\^gmkZm^]bgma^\hkg^kl%Z\hgl^koZmbo^ZiikhZ\ablmh\Ze\neZm^ Zg^__^\mboôZen^h_]+ZlbeenlmkZm^]bg?b`nk^l<-Z"mh^"' N Lhenmbhg3bm^kZm^qln\amaZm:lG6:lF

C9.3 Rectangular column charts :em^kgZmboêr:lfZr[^^lmbfZm^]_khf\henfg\aZkml' ?b`nk^l<-Z"mh<-^"`bo^ghg&]bf^glbhgZe]^lb`g\aZkml_hklrff^mkb\Zeerk^bg_hk\^]k^\mZg`neZk \henfglpa^k^k^bg_hk\^f^gmblZllnf^]mh[^\hg\^gmkZm^]bgma^\hkg^kl' Bgma^l^\aZkml3 a\\ 6 )'1. _\d © .)FIZ _rd © .))FIZ Lbfieb_b^]lmk^ll[eh\dZllnf^]' :l 6 mhmZeZk^Zh_k^bg_hk\^f^gmk^jnbk^] 6 !:l _rd ([a_\d"[a_\d (_rd pa^k^ !:l _rd ([a_\d"bl]^kbo^]_khfma^ZiikhikbZm^]^lb`g\aZkmbgm^kiheZmbg`Zlg^\^llZkr [^mp^^g\aZkml_hkmaôZen^h_]+(a_hkma^l^\mbhg' [6[k^Z]mah_l^\mbhg a6a^bàmh_l^\mbhg Pa^k^k^bg_hk\^f^gmblghm\hg\^gmkZm^]bgma^\hkg^kl%Z\hgl^koZmbo^ZiikhZ\ablmh\Ze\neZm^ Zg^__^\mboôZen^h_]+ZlbeenlmkZm^]bg?b`nk^l<-Z"mh^"' ]+ 6 ^__^\mbo^]îmamhlm^êbgeZr^k+

206

:ii^g]bq<3=^lb`gZb]l 1.3 Kr = 0.2

d 2 /h = 0.05

hf c

k

1.2 k /b

0.3

h/2

fy

1.1

A

s

h

0.8 NEd/bhfck

d2

0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1

0.9

0.7 0.6 0.5

Centroid of bars in half section

0.5 0.6 0.7

0.8

0 0.4

0.9 0.3

1.0

0.2 0.1 0

0

0.05

0.10

0.15

0.20

0.25 MEd/bh2fck

0.30

0.35

0.45

0.40

Figure C4a) Rectangular columns ]2/a = 0.05

1.3

Kr = 0.2 ck

d 2 /h = 0.10

1.2

k /b

hf

0.3

h/2

A

s

fy

1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1

1.0 0.9 0.8 NEd/bhfck


0.4

1.0

1.0

0.7 0.6 0.5

h

0.4

d2 Centroid of bars in half section

0.5 0.6 0.7

0.8

0 0.4

0.9 0.3 Kr = 1

0.2 0.1 0

0

0.05

0.10

0.15

0.25 0.20 MEd/bh2fck

0.30

0.35

0.40

0.45

Figure C4b) Rectangular columns ]2/a = 0.10

207

1.3 Kt = 0.2

d 2 /h = 0.15 k

1.2

hf c

0.3

k /b

h/2

fy

1.1

A

s

h

1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1

1.0 0.9

0.7 0.6 0.5

d2 Centroid of bars in half section

0.5 0.6

0.7 0.8

0 0.4

0.9 0.3 Kr = 1

0.2 0.1 0

0

0.05

0.10

0.15

0.20 MEd/bh2fck

0.25

0.40

0.35

0.30

Figure C4c) Rectangular columns ]2/a = 0.15

1.3

Kr = 0.2

d 2 /h = 0.20

hf

ck

1.2

h/2

fy

k /b

0.3

1.1

s

h

A 1.0

1.0 0.9 0.8 0.7 0.6 0.5

0.9 0.8 NEd/bhfck


NEd/bhfck

0.8

0.4

0.7

0.4

d2

0.6

0.4 0.3 0.2 0.1

0.6 0.5

Centroid of bars in half section

0.5

0.7

0

0.8

0.4

0.9

0.3 0.2

Kr = 1

0.1 0

0

0.05

Figure C4d) Rectangular columns ]2/a = 0.20

208

0.10

0.15

0.20 MEd/bh2fck

0.25

0.30

0.35

:ii^g]bq<3=^lb`gZb]l 1.3 Kr = 0.2

d 2 /h = 0.25

hf c

k

1.2

h/2

fy

k /b

0.3

1.1

s

h

A 1.0

1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1

0.9


NEd/bhfck

0.8 0.7 0.6 0.5

d2

0.4

Centroid of bars in half section 0.5

0.6

0.7

0

0.4

0.8

0.3

0.9

0.2 0.1

Kr = 1 0

0

0.05

0.10

0.15 MEd/bh2fck

0.20

0.25

0.30

Figure C4e) Rectangular columns ]2/a = 0.25

C9.4 Biaxial bending in rectangular columns :lZ_bklmlmî%lîZkZm^]^lb`gbg^Z\aikbg\biZe]bk^\mbhg%]blk^`Zk]bg`[bZqbZe[^g]bg`%fZr[^ ng]^kmZd^g'Gh_nkma^k\a^\dblg^\^llZkrb_)'.©l r (l s©+')Zg]%_hkk^\mZg`neZkl^\mbhgl%)'+ ª!^r(a^j"(!^s ([^j"hk!^r(a^j"(!^s ([^j"ª.')'Hma^kpbl^l^^L^\mbhg.'/',h_nkh\h]^+'

Concise: 5.6.3

?hkljnZk^\henfgl!^r (a^j "(!^s ([^j"6F>]r(F>]s'

C9.5 Circular column charts BgZlbfbeZkfZgg^kmh<2',%ma^Zk^Zh_k^bg_hk\^f^gm_hk\bk\neZk\henfgl:lfZr[^^lmbfZm^] _khfma^\aZkmlbg?b`nk^l<.Z"mh<.]"' Bgma^l^\aZkml3 a\\6 )'1. _\d © .)FIZ _rd 6 .))FIZ :l 6 mhmZeZk^Zh_k^bg_hk\^f^gmk^jnbk^] 6 !: l _ rd (a +_ \d"a + _ \d (_ rd pa^k^!:l _rd (a+_\d"bl]^kbo^]_khfma^ZiikhikbZm^]^lb`g\aZkmbgm^kiheZmbg`Zlg^\^llZkr' ](a6 ^__^\mbo^]îma(ho^kZee]bZf^m^k'

C9.6 Links Ebgdl bg \henfgl lahne] [^ Zm e^Zlm 1 ff hk fZqbfnf ]bZf^m^k h_ ehg`bmn]bgZe [Zkl(- bg ]bZf^m^kZg]Z]cZ\^gmmh[^ZflZg]leZ[lliZ\^]Zmmaê^Zlmh_3 N *+mbf^lma^fbgbfnf]bZf^m^kh_maêhg`bmn]bgZe[Zk% N /)h_maê^ll^k]bf^glbhgh_ma^\henfg%hk N +-)ff'

209

k /h 2 fc k

1.2

Ratio d/h = 0.6

A

s

fy

0.2

1.1

1.0 1.0

0.9

0.9

0.8

d

0.3

h

0.4

0.7 0.5

0.6 0.5

0.7

0.6

0.4 0.6

0.3 0.2

0.5

0.7

0.1 0

0.4

0.8 0.9

0.3 0.2

Kr =1

0.1 0

0

0.01

0.02

0.03

0.04

0.06

0.05

0.07

MEd /h3fck Figure C5a) Circular columns ]/a = 0.6

k /h 2 fc k

1.2 0.2

Ratio d/h = 0.7

A

s

fy

1.1

1.0

1.0

0.9 0.8 0.7

0.9 0.8 NEd /h2fck


NEd /h2fck

0.8

0.6

0.5 0.6

0.2 0.1

0.5

h

0.4

0.6 0.5 0.4 0.3

0.7

0.4

d

0.3

0.7

0

0.3

0.8

0.2 Kr =1

0.1 0 0

Figure C5b) Circular columns ]/a = 0.7

210

0.02

0.04

0.06 MEd /h3fck

0.08

0.10

0.12

:ii^g]bq<3=^lb`gZb]l

Af s y / 2 k h f c

k

1.2 0.2 1.1

0.9

0.8 0.7

0.8

NEd /h2fck

0.5

0.4 0.3

0.6

0.6

0.2 0.1 0

0.5 0.4

0.7 0.8

0.3

0.9

0.2 0.1 0

h

0.4

0.6 0.5

0.7

Kr =1

0

0.02

0.06

0.04

0.08

0.10 MEd /h3fck

0.12

0.16

0.14

0.18

0.20

Figure C5c) Circular columns ]/a = 0.8

Af s y /h 2 k f

ck

1.2 0.2 1.1

1.0

1.0

Ratio d/h = 0.9 d

0.3

h

0.9 0.9

0.8 0.7 0.6

0.8

0.4 0.5

0.5 0.4 0.3

0.7 NEd /h2fck


d

0.3

1.0 0.9

1.0

Ratio d/h = 0.8

0.6

0.6

0.2 0.1

0.5 0.4

0.7

0

0.8

0.3 0.9

0.2 0.1 0

0

Kr =1 0.05

0.10

0.15

0.20

0.25

0.30

MEd /h3fck Figure C5d) Circular columns ]/a = 0.9

211

Eurocode 2 resources Publications Concise Eurocode 2 <nkh\h]^+Zg]bmlNDGZmbhgZe:gg^q

How to design concrete structures using Eurocode 2 <nkh\h]^+


Economic concrete frame elements to Eurocode 2 <
Precast Eurocode 2: Design manual <nkh\h]^+Zg]bmlGZmbhgZe:gg^q

Precast Eurocode 2: Worked examples <nkh\h]^+Zg]bmlGZmbhgZe:gg^q

Concrete buildings scheme design manual <\aZkm^k^]f^f[^klabi^qZfbgZmbhg%[Zl^]hg><+

Properties of concrete for use in Eurocode 2 <nkh\h]^+

Standard method of detailing structural concrete Bglmbmnmbhgh_Lmkn\mnkZe>g`bg^^kl(Ma^
Manual for the design of concrete building structures to Eurocode 2 Bglmbmnmbhgh_Lmkn\mnkZe>g`bg^^kl%+))/ :fZgnZe_hkma^]^lb`gh_\hg\k^m^[nbe]bg`lmh>nkh\h]^+Zg]bmlGZmbhgZe:gg^q

BS EN 1992-1-1, Eurocode 2 – Part 1-1: Design of concrete structures – General rules and rules for buildings ;kbmblaLmZg]Zk]lBglmbmnmbhg%+))-

National Annex to Eurocode 2 – Part 1-1 ;kbmblaLmZg]Zk]lBglmbmnmbhg%+)).

Software RC spreadsheets: V3. User guide and CD <q\êlik^Z]la^^ml_hk]^lb`gmh;L1**)Zg]>nkh\h]^+Zg]bmlNDGZmbhgZe:gg^q

Websites Eurocode 2 – www.eurocode2.info Eurocodes Expert – www.eurocodes.co.uk The Concrete Centre – www.concretecentre.com Institution of Structural Engineers – www.istructe.org 212


F^f[^klh_ma^Lm^^kbg`@khni ChagFZlhg LmnZkm:e^qZg]^k IZe
:eZg;Zqm^k:llh\bZm^l!
F^f[^klh_ma^nkh\h]^+@khni!@" ChagFhhk^
=
BgbmbZel^\mbhg]kZ_ml * Bgmkh]n\mbhg + :gZerlbl%Z\mbhglZg]ehZ]ZkkZg`^f^gml , LeZ[l - ;^Zfl .
GZkrGZkZrZgZg GZkrGZkZrZgZg
3


Phkd^]>qZfie^lmh>nkh\h]^+3Ohenf^*

Mablin[eb\Zmbhg`bo^l^qZfie^lh_ma^]^lb`gmh >nkh\h]^+h_\hffhgk^bg_hk\^]\hg\k^m^ê^f^gml bgk^bg_hk\^]\hg\k^m^_kZf^][nbe]bg`l' Pbma^qm^glbo^\eZnl^k^_^k^g\bg`%k^Z]^klZk^`nb]^] makhnà]^lb`g^qZfie^lmh>nkh\h]^+Zg]hma^kkêôZgm >nkh\h]^lZg]k^_^k^g\^l'Maîn[eb\Zmbhg%pab\abg\en]^l ]^lb`gZb]l%Zbflmhaêi]^lb`g^klpbmama^mkZglbmbhgmh ]^lb`gmh>nkh\h]^l'

nkh\h]^+mhma^ND'

Ohenf^*Phkd^]>qZfie^lmh>nkh\h]^+bliZkmh_ZkZg`^ h_k^lhnk\^lZoZbeZ[e^_khfMa^nkh\h]^l'?hkfhk^bg_hkfZmbhg oblbmppp'^nkh\h]^+'bg_h'

<

Worked Examples to Eurocode 2.pdf

Recommend Documents