PP3-A1425E

INSTAL INS TALL L A TIO TION N GUI GUIDE DE

FRONTIER WORKFLOW MANAGEMENT SOFTWARE

MS01 MS01 Softw are Versi Versi on 4.0 Universal Guide for Service Technician Use

First irs t Edition

Copyright Notice © Copyright 2006-2011 FUJIFILM Corporation Frontier Workflow Management Software MS01 Installation Guide All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, translated, or stored in a retrieval system in any form or by any means, without the prior written consent of FUJIFILM Corporation.

Software Licensing Agreement PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE OPENING THIS PACKAGE OR USING THIS SOFTWARE. OPENING THIS PACKAGE OR USING THIS SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE WITH THESE TERMS AND CONDITIONS, PROMPTLY RETURN THIS SOFTWARE UNOPENED TO YOUR SUPPLIER AND YOUR MONEY WILL BE REFUNDED. This Software License Agreement is a legal document between you (a single entity) and FUJIFILM Corporation (the "Licensor") for the MS01 Frontier Workflow Management Software (the "Software"). The Software includes the Frontier Workflow Management Software MS01 software, the associated media, any printed materials and any electronic documentation. By using the Software, you agree to the terms of this Software License Agreement. The Licensor grants you a non-exclusive, non-transferable license to use one copy of the Software in object code only.

Ownership Retained By Licensor FUJIFILM Corporation owns all title and copyrights in and to the Software and the Licensor has the ful l right and authority to grant the license granted herein. Your license does not give you any title or ownership in the Software, nor is it a sa le of any rights in the Software. The only right granted to you is the right to use the Software in accordance with the terms of this Software License Agreement. All rights not specifically granted to you under this Software License Agreement are reserved by the Licensor. You may make only a single copy of this Software as a backup copy, provided that it includes all notices and markings, including copyright, trademark and other proprietary notices as on the original. Such backup copy of the Software may not be in use at any time unless the original Software is damaged beyond use, and it must remain in your possession and control. You may not copy the Software onto any public network. You may not, and you may not allow others to, modify, disassemble, decompile, translate, reverse engineer, reproduce, make derivative works of or enhance the software. You ma y not, and you may not allow others to, rent, lease, sell, sublicens e or otherwise transfer the Software to any other person. In addition to any other rights it may have, the Licensor may terminate this Software License Agreement if you fail to comply with the terms and conditions hereof. In such event, you m ust cease all use of the Software and destroy all copies of the Software and all of its component parts. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. i

At the Licensor's sole discretion, the Licensor may from time to time provide you with updates to the Software. Any such updates shall become part of the Software licensed to you hereunder and subject to all of the terms and conditions of this Software License Agreement.

Disclaimer of Warranties The Licensor expressly disclaims any and all warranties relative to the Software. THE SOFTWARE IS PROVIDED “AS IS," WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR OF PARTICULAR PURPOSE AND NON-INFRINGEMENT AND THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LICENSED PRODUCT IS WITH YOU.

Limitation of Liability In no event shall the Licensor be liable for any direct, special, incidental, indirect or consequential damages whatsoever to you (including, without limitation, damages for loss of profits, sales or data or for business interruption) arising out of the use of or inability to use the Software, even if the Licensor has been advised of the possibility of such damages. In any event, the Licensor's entire liability under any provision shall be limited to the greater of the amount actually paid by you for the Software or $25. Because some states and jurisdictions do not allow the exclusion or limitation of liability, the above limitation may not apply to you. If any provision of the Software License Agreement is declared by a court of competent jurisdiction to be invalid for any reason, such invalidity shall not effect the remaining provisions hereof.

Governing Law This Software License Agreement shall be governed by the laws of the State of New York without regard to conflict of laws principles.

Term This License Agreement is effective until terminated. You may terminate this L icense Agreement by returning the Licensed Product to Licensor. Licensor m ay terminate this License Agreement if you breach any of the terms and conditions. Upon termination of this License Agreement for any reason, you shall return the Licensed Product to Licensor. All provisions of this Agreement relating to disclaimers of warranties, limitation of liability, remedies, or damages, and Licensor's proprietary rights shall survive termination. YOU ACKNOWLEDGE YOU HAVE READ AND UNDERSTAND THIS AGREEMENT AND AGREE TO BE BOUND BY ITS TERMS. YOU FURTHER AGREE THAT THIS AGREEMENT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE AGREEMENT BETWEEN YOU AND LICENSOR, AND SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS RELATING TO SUBJECT MATTER OF THIS AGREEMENT.

NY-177971 v3 0950000-102

MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. ii

Table of Contents

CHAPTER 1: INTRODUCTION .......................................................................................................................1

OVERVIEW ................................................................................................................................................................1 KNOW YOUR SYSTEM .............................................................................................................................................. 2 ICIII Computer ...............................................................................................................................................2 ICIII Supported Operating Systems ......................................................................................................3 FUJIFILM Printers ..........................................................................................................................................3 FUJIFILM Scanners ........................................................................................................................................3 Third-Party Hardware ..................................................................................................................................3 SYSTEM TERMINOLOGY ...........................................................................................................................................4 CHAPTER 2: DETERMINING PROPER INSTALLATION TYPE .....................................................12

OVERVIEW .............................................................................................................................................................. 12 INSTALLATION SETUP TYPES ................................................................................................................................ 12 Primary MS01 Setup Types – MS01 Server ...................................................................................... 12 Secondary MS01 Setup Types ................................................................................................................15 Setup Type Installation Matrix ...............................................................................................................17 CHAPTER 3: DETERMINING INSTALLATION WORKFLOW .........................................................18

Overview .........................................................................................................................................................18 INSTALLATION CHECKLISTS BY MS01 SETUP TYPE ...........................................................................................19 Primary MS01 Setup Type Installation Checklists .......................................................................... 19 Secondary MS01 Setup Type Installation Checklists .....................................................................24 CHAPTER 4: MS01 V4.0 INSTALLATION ..............................................................................................28

MS01 SERVER .......................................................................................................................................................28 PRINTER ..................................................................................................................................................................34 SCANNER ................................................................................................................................................................43 MS01 WITH PRINTER SUPPORT ...........................................................................................................................50 MS01 WITH SCANNER SUPPORT .........................................................................................................................58 MS01 WITH PRINTER AND SCANNER SUPPORT ..................................................................................................64 MS01 WORKSTATION ...........................................................................................................................................71 MS01 WORKSTATION WITH PRINTER SUPPORT ................................................................................................76 MS01 SERVER WITH TETHERED PRINTER ...........................................................................................................83 CANCELLING INSTALLATION .................................................................................................................................. 90 APPENDIX A: ADDITIONAL MS01 TASKS ............................................................................................91

VDENTRY & 1394 FIREWIRE SETUP................................................................................................................... 91 Preparation of FireWire Cards and Drivers ........................................................................................ 91 FireWire Card Installation ........................................................................................................................93 FIREWIRE – DRIVER INSTALLATION AND NETWORK CONFIGURATIONS .......................................................... 96 Windows XP FireWire Driver Installation and Network Configurations ...................................97 Windows 7 FireWire Driver Installation and Network Configurations ....................................106 ADJUSTING THE SYSTEM’ S DATE AND TIME PROPERTIES ................................................................................116 Windows XP – Date and Time Properties ......................................................................................... 116 Windows 7 – Date and Time Properties ............................................................................................117 ENSURING ADEQUATE SPC/MCU DISK SPACE ...............................................................................................122 MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. iii

INSTALLING & CONFIGURING THE ASK 2000, 4000, & 4000A PRINTERS ...............................................126 ASK Hardware Installation & Configuration ....................................................................................127 TO BACK UP (SAVE) SETTINGS .........................................................................................................................138 APPENDIX B: INFORMATION ABOUT MS01 .....................................................................................140

POWER FOR THE MS01 SYSTEM ........................................................................................................................140 Non-Connected Systems ........................................................................................................................140 Connected Systems .................................................................................................................................. 140 SUPPORT MODE ...................................................................................................................................................141 OPERATOR MODE ................................................................................................................................................. 143 ACCESSING MAINTENANCE ................................................................................................................................. 145

MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. iv

Ch ap t er 1 1: IIn t r o d u c t i o n Overview This universal guid e is intended for retail labs run ning FUJIFILM systems regardless of location. Important: Review this entir e guide to determine which sectio ns apply to you r lab before you begin installing any software.

This installation guide provides details and instructions for installing FUJIFILM’s Frontier W orkflow Management Software (MS01) for retail lab s ystems internationally. It may need to be used in association with a regional or retail client-specific guide. In this chapter, you will learn the various hardware pieces that can comprise a FUJIFILM system (see page 2).

MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 1

Know Your System It is very important to know your system configuration before installing the MS software to ensure proper functionality and performance.

ICIII Compu ter The minimum hardware requirements for ICIII computers is: Items

Specification

CPU

Core 2 Duo, 2.4GHz or more

Memory

2 GB or more

Hard Disk

160 GB

Clock Frequency

450 MHz or higher

External I/F

1000 BASE-TX USB 2.0 SCSI etc.

OS

Windows XP Professional SP3 Windows 7


Remarks

Two drive allocation: C and D

Depending on the peripheral equipment

ICIII Supported Operating Systems o

Windows XP Service Pack 3

o

Windows 7

FUJIFILM Scanners The MS software supports the following scanner models:

FUJIFILM Printers The MS01 software supports the following printer models: Network Printers 1 o DL 600 Inkjet Dry Lab Printer USB Printers o ASK 1500 Dry Lab Printer o ASK 2000 Dry Lab Printer o ASK 4000 Dry Lab Printer o ASK 4000A Dry Lab Printer

USB Scanners: o

1394 FireWire Printers: o LP 5500 Wet Lab Printer o LP 5700 Wet Lab Printer o LP 5900 Wet Lab Printer

SP 500

1394 FireWire Scanners: o

SP 1500

o

SP 2000

o

SP 3000

Third-Party Hardw are The MS01 software supports the following printer models: o

DYMO LabelWriter Printers

o

Epson Stylus Pro Wide Format Printers

o

Flatbed Scanners

1

This printer is installed via a separate installation guide. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 3

System Termi nolog y 330 Syst em

A tethered system consisting of an SLP 800 printer/scanner combination.

340 System

A tethered system consisting of an SLP 1000 printer/scanner combination.

350 System

A tethered system consisting of an LP 1500 wet lab printer and an SP 1500 or 2000 scanner.

355 System

A tethered system consisting of an LP 1500 wet lab printer and an SP 3000 scanner.

370 System


375 System


550 System


570 System


590 System


A1

Scanner software that works with the SP 1500, SP 2000, SP 2500, and SP 3000 scanners.

ASK

Dye-sublimation dry lab printers. See FUJIFILM USB printers in this glossary.

B1

Variety Print Service for SP 2000/2500 scanners not using FrontMan.

B5

Single Scan Digitizing Software for SP 2000/2500 scanners not using FrontMan.

B7

Professional Scanning Software for SP 2000/2500 scanners not using FrontMan.

B8

Hyper Reorder Software for SP 2000/2500 scanners not using FrontMan.

B9

Tone Selection Software for SP 2000/2500 scanners not using FrontMan.

B11

Hyper Retouch Software for SP 2000/2500 scanners not using FrontMan.

backprint

Text printed on the reverse side of the print. Sometimes customizable.

CD

Compact disc. Referred to in MS01 as Disc.

Composed Print

A composite created via MS01’s Compose feature. The template used to create a Composite Print was selected by the operator via the Choose Template dialog box.


Composite

The combination of a template and one or more images. It is displayed as an thumbnail in MS01’s View Images screen, and its thumbnail shows a preview of what will be printed. Quick Prints and Compose Prints created via MS gateways are all composites.

Connected

A connected MS01 system is a system that receives data from FUJIFILM’s fulfillment network, sends data to FUJIFILM’s Fulfillment Network, and receives orders from various sources (such as retailers and FUJIFILM labs). This is accom plished via Internet connectivity.

Cover

A Cover is an order’s thumbnail as displayed in the MS01’s View Images screen. It represents a print group.

Crop modes

MS01 offers different crop choices. For this example, assume that the original product size and image dimensions are: 8x10 Image

4x6 Product

Fill in

3.5x5 Image

Print area is filled with image and there may be image data lost if it does not match the aspect ratio of the print size selected. Output will have no white space. 8 x 10 Image

3.5 x 5 Image

Fit in

Fits the image into the size selected leaving it at its current aspect ratio to maintain all the image data. This will produce white space if the image is not the same aspect ratio as the size selected. 8 x 10 Image 3.5 x 5 Image

No resize

Image is rendered on the product without resizing. Takes the size selected and cuts out the center portion of the image (think of it as a cookie cutter). If the image is smaller than the size selected it will produce white space. 8 x 10 Image 3.5 x 5 Image


custom backprint

Backprint text specified by the operator; only replaces second l ine of backprint. Not all printers support the backprint feature. Also see backprint.

digital input

Digital images loaded into the system for printing (not film-based images). Examples include .jpg, .tif, and .gif image files generated from digital cameras.

Digital Link Request Spooler

One of the sub-applications of the MS01 system, this application performs all background processing for producing prints and CDs, receiving input from external sources such as kiosk, and communications with remote systems via the Internet. It also manages a database containing all production information, and is responsible for scheduling of tasks and devices throughout the system. This application is also known as Simon.

DL printers Duplex Printing Dymo Label

A line of FUJIFILM inkjet printers. DL stands for “Dry Lab.” Printing on both sides of the printer paper.

A small label printer used to output labels for CDs, kiosk orders, Web orders, etc.

E5

Fujicolor CD/DVD Digital software (also known as Backup CD Service).

Epson Stylus Pro

Wide-format printer used in some FUJIFILM regions. Supported models include 4880, 7800, 7880, 7900, 9880, 9900, and 11880.

FDD

Frontier Driver Direct. This service provides more control and greater messaging capabil ities when printing.

FDIA

FUJIFILM’s Frontier Digital Imaging Architecture.

FDIA DB

The database used by MS01 and other FUJIFILM and t hird-party software to facilitate image transfer and order fulfillment.

FCIM

Frontier Communication Interface Module.

film type

A film type must be selected if creating prints from film. Options include color, black and white, and slide film.

Frontier

The name used to describe FUJIFILM-developed systems.

FrontMan

The FrontMan software is an optional film input software interface included with MS01. (The FrontMan application window is also known as Main or the Order Entry screen.)


FMPC

Also known as the LPC and an abbreviation for Frontier Manager Printer Controller, the FMPC is a separate computer used to drive a laser printer (LP printer) and receive data from the scanner (if configured to do so). Note: Not all system configurations use an FMPC/LPC.

FUJIFILM Printers (1394 FireWire)

LP 1500 Wet Lab Printer





FUJIFILM Printers (Network)

DL 600 Inkjet Dry Lab Printer

FUJIFILM Printers (USB)

ASK 1500 Dry Lab Printer



ASK 4000A Dry Lab Printer


FUJIFILM Scanners (FireWire)

SP 1500

FUJIFILM Scanners (USB)

SP 500

Gateway

SP 3000

SP 2000

A gateway is an MS01 system interface that supports the creation of MS01 orders by external order interfaces.

HCIP

High capacity image processor. This is a rendering device attached to the MS01 system. By having an HCIP attached to your MS01 system, its order processing speed is increased.

Hot Job

Provides an order with a prioritized status.

HyperThreading

Officially called Hyper-Threading Technology (HTT), this is Intel Corporation’s trademark for their implementation of the simultaneous multithreading technology on their Pentium 4 microarchitecture. The technology improves processor performance under certain workloads by providing useful MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 7

work for execution units that would otherwise be idle, for example during a cache miss. A Pentium 4 with Hyper-Threading enabled is treated by the operating system as two processors instead of one. IC

Imaging controller.

ICIII

Imaging Controller III computer, formerly known as PIC (photo imaging controller computer) and DIC (digital imaging controller computer).

Image Info

One of the sub-applications of the MS01 system, Image Info allows operators to see information about the image data.

Index Print Job Manager

A supplementary print that displays image thumbnails. One of the sub-applications of the MS01 system, Job Manager manages the images in MS01 orders. Also known as JobMan.

Kaleida

A FUJIFILM printer used in some FUJIFILM regions. Supported model includes PX-7550.

Local Disc Writer

This is a CD/DVD writer attached to the IC or an IC Workstation. This allows for one (1) CD to be written at a time. Local CD/DVD writers do not have the ability to print the labels automatically on the CD/DVDs.

Log Off

One of the sub-applications of the MS01 system, the Log Off function shuts down the application and also performs a Windows operating system log off.

LP (Laser Printer)

This is the abbreviation that pre-pends some FUJIFILM printer model names. For example, LP 5000.

LPC

Maintenance

Also known as the FMPC, and an abbreviation for Laser Printer Controller, the LPC is one of the terms used as a name for the computer, which is separate from the ICIII computer that is used to drive a printer. One of the sub-applications of the MS01 system, the MS01 Maintenance application houses the software used to configure the MS01 system. This is a different application than the Maintenance offered via the printer software.

MCU (Main Control Unit)

Known as the SPC in some regions, the MCU is the co mputer that drives the film scanner hardware. Note: The SP 500 runs via the ICIII without a separate SPC/MCU device.

Media

SD/Memory Stick/Compact Flash/xD Card/Compact Flash/CD/DVD used to store digital images.


MS01

Also known as the Frontier Workflow Management Software. This is the overall system, including the scanner software and the printer software. Operators should always use the system in Operator mode.

MS11

Scanner software that works with SP 500, 1500, 2000, 2500, and 3000 model scanners. This is a sub-component of the MS01 system.

MS12

Printer driver support software for Adobe Photoshop CS3 and CS4.

MS13

LAN spool software.

MS14

Variety Print Service software.

MS15

Variety Template Composite / Variety Templates software, including Template Editor.

MS16

Image-Adjust software. Also called 6-frame adjust.

MS17

Net Connection for FDI-net software.

MS18

Skin Color Correction Image Processing software.

MS19

Photo ID Print Service software.

MS21

Express Variety Print Software.

Multi-Roll Order

A multi-roll order is an order that contains more than one roll of film. Each roll in a multi-roll order has a unique Film ID (which is included in the backprint information).

Operator Mode

On the ICIII, this mode locks down the system so only Fuji applications can be used. After logging to Operator mode (default mode), Fuji applications automatically launch, and automatically re-launch if terminated.

Page

Page is the term used to refer to a Composite when it is part of a Print Group.

Panda (Print er And Device Ap pl icat io n)

One of the sub-applications of the MS01 system, Panda provides an interface between the Digital Link Request Spooler (Simon) and various devices, such as printers and CD-writers. It manages device operations and provides status and m essages to the rest of the system in a consistent manner to ensure that devices may easily be interchanged or added, as needed.

Personality

Custom MS system settings associated with a particular FUJIFILM region or retailer.

PIC

Photo Imaging Controller, now known as IC.

Print Group

A Print Group is set of composites that are processed together as a single product, such as a MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 9

photo book. A Print Group consists of a Cover and a set of Pages. Product

On the MS01 system, each print created has an associated “product” file. For example, there are product files for 4x6-sized prints,

Production Manager

The mechanism in the MS01 system that manages routing ordered products to output devices for production. It also handles ordering the output based on due time, etc.

Promo Print

Puma

Quick Print

Red exclamation mark

A product that enables retailers to print promotional offers (using the MS01 system) for distribution to consumers. One of the sub-applications of the MS01 system, Puma is the mechanism used to display system messages (such as errors, warnings, and informational messages). A Quick Print is a composite created as the result of a Quick Print operation in MS01. The template used is not user-selectable; it is the template for the Quick Printed product. This will power off the ICIII system. For proper shut-down procedures, see the MS01 Start-up and Shut-down Guide. On the FMPC, this is an emergency shutdown for only the Panda application. This will not power off the FMPC box. Note: This is not the proper shut-down procedure for this device; only do this if directed to do so by Technical Support. Important: For systems that are not connected to the FUJIFILM fulfillment network, this

function can be used as a proper method of shutting down the system. For systems that are connected to the FUJIFILM fulfillment network, this should be treated as an emergency shut-down command only. By clicking this button, you are not performing a proper shut-down procedure. Only use this button if instructed to do so by Technical Support. Retain Prin t Settings

Enables you to retain the size, surface, and co lor settings between orders.

Rimage

This is a third-party CD burning device designed for high volumes of CD creation. This system allows multiple CDs to be written simultaneously. The Rimage system can print labels directly onto CDs. Depending on the model of Rimage, it may have two or four CD burners and a single printer.

S3

Variety Print Service for SP 3000 scanners not using FrontMan.

S5

Professional Software for SP 3000 scanners not using FrontMan.

Scan Modes

Auto: When using film input, if the operator selects Auto as the scan mode, the system scans six images at a time without requiring the operator to press . Pressing any key on the keyboard will stop the Auto Mode and will allow image adjustments as in Semi Mode. Manual: Manual operates just as semi mode operates, but you can choose size and quantity for each frame. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 10

Semi: When using film input, if the operator selects Semi as the scan mode, the system scans six images at a time and the operator can correct the color and density on each image as necessary. The operator then presses to scan the next set of six images. Simplex Printing Software Launcher

Printing on only one side of the printer paper.

This is a tool that allows the user to switch to any of the programs that are currently running. Also known as the Switcher application, this replaces the need for the Windows function.

SP

The abbreviation that pre-pends FUJIFILM scanner model names. For example, SP 500.

SPC

Known as the MCU in some regions, this is the name for the computer that drives the scanner. Note: The SP 500 runs via the ICIII without a separate SPC/MCU device.

Summary Sheet

A print output that includes the file names of the images in the order.

Surface

Prints can be produced using different surface textures. Some printer models can onl y print on certain surface types. Surfaces include Gl ossy, Lustre, Matte, Silk, SupremeG, SupremeL, Thin, SupremeM, ThinGlossy, GlossyRoll, SatinRoll, SemiGlossBoard, CanvasRoll, CatsbyRoll, PearlRoll, SatinCanvasRoll, AquarellRoll, TalbotRoll, ScrimVinyl, and PearlPosterBoard.

Support Mode

On the ICIII, this mode allows the user to access the operating system. After logging to Support mode, Fuji applications automatically launch but do not re-launch if terminated.

Third-Party Printers

MS01 4.0 supports various models of Epson Stylus Pro Wide Format Printers, Xerox Phaser Printers, and Rimage CD duplicators.

Whole Roll

A product type applied to an image that will make <#> of each image in the order.

Workstation

This is another digital input system for the MS01 software. It allows control of a printer, digital ingest, and CD/DVD burning.

Xerox printers

Color printers used in some FUJIFILM regions. Supported models Phaser 7760.


Ch ap t er 2 2: D Det er m i n i n g P Pr o p er IIn s t al l at i o n T Ty p e Overview There are various installation methods for the dep loyment of MS01 version 4.0. It is essential that you perform the correct installation. See pages 12 -16. Some portions of installation are documented in s eparate guides; contact your FUJIFILM subsidiary for the proper diagram for your lab. It is essential to use the proper guides for you r lab/configur ation when installing.

Important: See the next s ection, Installation Setup Types for detailed infor mation on t he various MS01 setup t ypes. Once you have determined the appropri ate setup t ype for you r lab, refer to the corresponding installation checklist.

Installation Setup Types When you run the installer, there will be a Setup Type screen that provides ten software installation options to choose from. The installation option you choose is determined by the hardware configuration of your system. Use the definitions in this section to determine the appropriate setup type for your lab, and then refer to the corresponding installation workflow in Chapter 3: Determinin g Installation Workf low .

Primary MS01 Setup Types – MS01 Server This section defines the primary MS01 setup types – MS01 Server configurations. Installation of an MS01 Server setup type is mandatory for all labs. Some MS01 Server setup types incorporate the installation of secondary setup types which can be either required or optional. Read this section carefully in order to determine the proper primary MS01 setup type to install in your specific lab. MS01 Server Installation (see page 19).

The MS01 Server in stallation setup type installs the MS01 software on an ICIII computer.


MS01 Server with Printer Support Installation (see page 20).

The MS01 with Printer Support installation setup type installs the MS01 and printer functionality on the ICIII server. Supported printers in this configuration include network and USB printers. Supported scanners in this configuration include FireWire scanners only.

MS01 Server w ith Scanner Support Installation (see page 21).

The MS01 Server w ith Scanner Support installation setup type installs the MS01 and scanner functionality on the ICIII server. Supported scanners in this configuration include USB scanners only. Printer support should be added via a separate computer.


MS01 Server with Printer and Scanner Support Inst allation (see

page 22). The MS01 Server wi th Printer and Scanner Support installation setup type installs the MS01, printer, and scanner functionality on the ICIII server. Supported printers in this configuration include network and USB printers. Supported scanners in this configuration include USB scanners only.

MS01 Server w ith Tethered Printer Installation (see page 23).

This is a legacy configuration where the printer and scanner are connected to each other via FireWire. The scanner is connected to the ICIII via network connection.


Secondary MS01 Setup Types This section defines secondary MS01 setup types. These setup types can be either required and/or optional, depending on the primary MS01 setup t ype appropriate for your specific lab. Refer to the appropriate MS01 Server setup type checklist in the Installation Checklist s by MS01 Setup Type section to determine which of these other MS01 setup types are appropriate for your lab. Printer Installation (see page 24).

The Printer installation setup type installs the printer functionality on an FMPC/LPC computer. Supported printers in this configuration include network and FireWire printers.

Scanner Installatio n (see page 25).

The Scanner installation setup type installs the scanner functionality on the SPC/MCU. Supported scanners in this configuration include FireWire scanners only.

MS01 Workstation Installation (see page 26).

The MS01 Workst ation installation setup type enables you to add additional MS01 workstation computers to the system. A scanner is not connectable to a workstation.


MS01 Workst ation wit h Printer Support Installatio n (see page 27).

The MS01 Workstation wi th Print er Support installation setup type installs an additional MS01 workstation computer with added printer support (additional printer). Supported printers in this configuration include network and USB printers.

Cancelling Inst allation (see page 90).


Setup Type Installation Matrix The following installation matrix illustrates which secondary MS01 setup types are either required or optional for installation during the installation of a primary MS01 setup type. Primary MS01 Setup Types – (Select one for install)

MS01 Server

MS01 Server with Printer Support

MS01 Server with Scanner Support

Secondary MS01 Setup Types

Printer

Required

Scanner

MS01 Workstation

MS01 Server with Printer and Scanner Support

Required – if printer is installed on server Required – only if system includes an MCU/SPC

Optional

MS01 Server with Tethered Printer Support

Optional

Required – only if system includes an MCU/SPC Optional

MS01 Workstation with Printer Support


Optional

Ch ap t er 3 3: D Det er m i n i n g IIn s t al l at i o n W Wo r k f l o w Overview The following installation checklists are categorized categorized based on the steps required during installation. installation. Important: It is mandatory t o inst all one of th e Primary [MS01 [MS01 Server] Server] setup typ es in each lab. If If additional (required or op tional) setup types are necessary, necessary, the specific Prim ary MS01 MS01 Server Server installation checklist will refer you to the appropriate steps to follow for each additional setup type. 



For definitions of each MS01 setup type, see pages 12 pages 12 -16. For installation workflow information refer to the appropriate checklist for your labs primary MS01 setup type: MS01 Server – Installation Checklist , on page 19. MS01 MS01 Server Server with Printer Suppor t – Installation Checkli st, on page 20. page 20. MS01 MS01 Server Server with Scanner Suppor Suppor t – Installation Checklist , on page 21. page 21. MS01 MS01 Server Server with Printer and Scanner Support – Installation Checklist , on page 22. page 22. MS01 MS01 Server Server with Tethered Tethered Printer Support – Installation Checklist , see page 23. page 23. For installation workflow information refer to the appropriate checklist for your labs required/optional secondary MS01 setup types: Printer – Installation Installation Checklis t , on page 24. page 24. Scanner Scanner – Installation Checkli st , on page 25. page 25. MS01 MS01 Workst Workst ation – Installation Checklist , on page 26. page 26. MS01 MS01 Workstation w ith Print er Suppor Suppor t – Installation Checklist , on page 27. page 27. 




















Installatio n Checklists Checkli sts by MS01 MS01 Setup Setup Type Follow the installation order-of-operations corresponding to the MS01 setup type appropriate for your lab. Chapter 2: Determining Proper Installatio n To determine the correct setup type for your lab, refer t o Chapter Type.

Primary MS01 MS01 Setup Setup Type Inst Installation allation Checklists Checkli sts Now that you have determined the proper primary MS01 setup type for your lab, find its corresponding installation checklist in this section. Carefully follow the steps in the checklist. There will be instances in which you will need to reference other sections in this manual. After you complete the steps in those other sections, be sure to return to this section and complete the remainder of steps in the appropriate primary MS01 setup type checklist. MS01 MS01 Server Server – Installation Checklis Checklis t

1

Install the base operating system. (Refer to instructions provided by your your FUJIFILM subsidiary.)

2

Verify the system date and time properties (see page 106) page 106)..

3

Perform additional pre-installation tasks. (Refer to instructions provided by your FUJIFILM subsidiary.)

4

Install the MS01 software on the ICIII, selecting MS01 Server as as setup type (see page 28) page 28)..

5

Install other MS01 setup types: 



Installation Checklist on page 24) Required: Printer (refer to Printer – Installation page 24) MS01 Workst Workst ation – Installation Checklist page 26) Optional: Workstation (see MS01 page 26)

Important: Once the steps for i nstallin g other MS01 MS01 setup setup t ypes are compl ete, return to t his checklist and com plete the remaining steps.

6

Install additional, optional components, such as the: 







7

Epson Stylus wide format printer Xerox Phaser printer Flatbed scanners DL 430/450/600 printer

Configure the MS01 software and perform necessary post-installation tasks ( as defined by your FUJIFILM subsidiary). Note: This step may not be necessary if your subsidiary has already customized your installer.

8

Perform system backup (see page 91) page 91)..


MS01 MS01 Server Server with Prin ter Support – Installation Checkli st

1

Install the base operating system. (Refer to instructions provided by your FUJIFILM subsidiary.)

2

Verify the system date and time properties (see page 106) page 106)..

3


4

MS01 with Printer Support as setup type (see Install the MS01 software on the ICIII, selecting MS01 page 50) page 50)..

5

Install the printer software and register the printer.

6

Install other required or optional components: 





If no other system hardware exists, proceed to the next step Scanner – Installation Checklist If the system includes an MCU/SPC , install Scanner (refer to Scanner on page 25) page 25) Install optional MS01 setup types: Workstation (see page 26) page 26) 

Important: Once the steps for install ing these required or optional comp onents are complete, return to this checklist and complete the remaining steps.

7

If you chose ASK as the printer type during MS01 installation, perform tasks on page 126. page 126. Important: Once the ASK ASK prin ter steps are complete, return to t his checkli st and compl ete the remaining steps.

8








9


Configure the MS01 software and perform necessary post-installation tasks ( as defined by your FUJIFILM subsidiary).

Note: This step may not be necessary if your subsidiary has already customized your installer. 10

Perform system backup (see page 91) page 91)..


MS01 Server w ith Scanner Support – Installation Checklist

1


2

Verify the system date and time properties (see page 106).

3


4

Install the MS01 software on the ICIII, selecting MS01 wit h Scanner Support as setup type (see page 58).

5

Install the scanner software.

6

Install other MS01 setup types: 



Required: Printer (refer to Printer – Installation Checklist on page 24) Optional: Workstation (see MS01 Workst ation – Installation Checklist page 26)

Important: Once the steps for i nstallin g other MS01 setup t ypes are compl ete, return to t his checklist and com plete the remaining steps.

7








8



9

Perform system backup (see page 91).


MS01 Server w ith Prin ter and Scanner Support – Installation Checklist

1


2


3


4

Install the MS01 software on the ICIII, selecting MS01 with Printer and Scanner Support as setup type (see page 64).

5


6

Install the scanner software.

7






If no other system hardware exists, proceed to the next step If the system includes an MCU/SPC , install Scanner (refer to the Scanner – Inst allation Checklist on page 25) Install optional MS01 setup types: Workstation (see MS01 Workst ation – Installation Checklist , page 26) 

Important: Once the steps for install ing these required or optional comp onents are complete, return to this checklist and complete the remaining steps.

8

If you chose ASK as the printer type during MS01 installation, perform tasks on page 126. Important: Once the ASK prin ter steps are complete, return to t his checkli st and compl ete the remaining steps.

9








10



11



MS01 Server w ith Tethered Printer Support – Installation Checklist

1


2


3


4

Install the MS01 software on the ICIII, selecting MS01 Server with Tethered Printer as setup type (see page 83).

5


6








7

If the system includes an MCU/SPC , install Scanner (refer to Scanner – Installation Checklist on page 25).



8



Secondary MS01 Setup Type Installati on Checklist s This section provides installation order-of-operations for the various secondary MS01 setup types. You have been referred to this section by an installation checklist for a primary MS01 setup type in the Primary MS01 Setup Type Installation Checklists section. Carefully follow the steps in the appropriate checklist in this section. There will be instances in which you will need to reference other sections in this manual. After you complete the steps in those other se ctions, return to this section and complete the remainder of steps in the appropriate secondary MS01 setup type ch ecklist. Once you have completed all steps in the appropriate secondary MS01 setup type checklist, return to the primary MS01 setup type checklist which referred you to this section and complete the remainder of the steps in t hat checklist. Printer – Installation Checklist Important: The MS01 Server must be powered on w ith the MS01 software runnin g to enable successful installation on all computers in the system.

1

Install the operating system on the LPC/FMPC computer. (Refer to instructions provided by your FUJIFILM subsidiary.)

2


3


4

Perform FireWire and Vdentry tasks (see page 91) ONLY for the following LP printer models : 

5500



5700



5900

5

Install the MS01 software, selecting Printer as setup type (see page 50).

6

For the DL 4x0/600 printers, install the printer software & register the printer. Otherwise, move on to the next step.

7




8

Epson Stylus wide format printer Xerox Phaser printer





Flatbed scanners DL 430/450/600 printer


9


10

Return to the appropriate Primar y MS01 Setup Types – MS01 Server installation checklist, and complete remaing steps.


Scanner – Installation Checklist Important: The MS01 Server must be powered on w ith t he MS01 softw are running to enable successful installation on all computers in the s ystem.

1

Install the operating system on the MCU/SPC computer. (Refer to instructions provided by your FUJIFILM subsidiary.)

2


3


4

Install the appropriate scanner software based on scanner model.

5

Install the MS01 software, selecting Scanner as setup type (see page 58).

6

Enable Event Viewer logging settings on the scanner’s SPC/MCU (refer to instructions provided by your FUJIFILM subsidiary.)

7


8


9



MS01 Workstation – Installatio n Checklist Important: The MS01 Server must be powered on w ith t he MS01 softw are running to enable successful installation on all computers in the s ystem.

1

Install the operating system on the Workstation computer. (Refer to instructions provided by your FUJIFILM subsidiary.) Important: You must install t he same base operating system that i s install ed on the MS01 Server associated with this system.

2


3


4

Install the MS01 software, selecting MS01 Workst ation as setup type (see page 71).

5






6

Epson Stylus wide format printer Xerox Phaser printer Flatbed scanners


7


8

Return to the appropriate Primar y MS01 Setup Types – MS01 Server installation checklist, and complete remaining steps.


MS01 Workstatio n wit h Printer Support – Installation Checklist Important: The MS01 Server must be powered on w ith t he MS01 softw are running to enable successful installation on all computers in the s ystem.

1

Install the operating system on the Workstation computer. (Refer to instructions provided by your FUJIFILM subsidiary.) Important: You must install t he same base operating system that i s install ed on the MS01 Server associated with thi s system.

2


3


4

Install the MS01 software, selecting MS01 Workst ation wi th Printer Support as setup type (see page 76).

5

Install the printer software & register the printer. If you chose ASK as the printer type during MS01 installation, p erform tasks on page 126.

6








7



8


9



Ch ap t er 4 4: M MS01 v v 4.0 IIn s t al l at i o n MS01 Server Selecting the MS01 Server installation setup type installs the MS01 software on an ICIII computer.

>>> To install MS01 Server: 1

Before beginning thi s installation , you must compl ete all pre-MS01 installati on tasks referenced in th e installation checkli st for this MS01 setup type (page 19).

2

Insert the MS01 Installation CD into the ICIII’s CD-ROM drive. The installer automatically launches. NOTE: If it does not, navigate to the CD-ROM drive via the W indows Start > Run or Explorer feature, and double-click the set up. exe file in the EZ171 directory. The software launches, and the Choose Setup Language screen displays.

3

Select the language that the software should display.

4

Click Next >.


A Preparing Setup screen displays and selfdismisses.

The Choose Setup Language screen closes, and the InstallShield Wizard launches, using the selected language.

5

Click Next >. The Setup Type > Select System Type screen displays.


6

From the drop-down menu, select MS01 Server .

7

Click Next >. The Setup Type > Additi onal Security screen displays.

8





9

To lock down the system to prevent the end user from accessing the operating system while running the Fuji software (operator mode), select the Ad d ad di ti on al s ecu ri ty t o t hi s s ys tem check box. If Add ad di ti on al s ecu ri ty to th is sy st em is not selected, users will have access to the operating system.

Click Next >.


The Setup Type > Disc Wri ter Support screen displays.

10

11



If the system will be using a CD writer, select the Local Disc Writer option.



If the system will be using a Rimage CD duplication device, select the Rimage option.



If the system will not be writing CDs, select the None option.

Click Next >. The Edit Data > Enter the name of the FMPC syst em screen displays.

12

In the Printer field, enter the name of the FMPC/LPC to be connected to the printer. Note: Ensure that names do not exceed 15 characters.

13

Click Next >. Note: If an error dialog opens, then a component name has been incorrectly typed into a n Edit Data screen. Click OK and the Edit Data information that needs to be changed will appear.


The Information screen displays.

14

Review the system information displayed in this screen.

15

If the information is incorrect, click < Back to navigate to previous selection screens, and modify settings, as appropriate. If the information is correct, click Next >. The Setup Type > Installi ng screen displays.

Installation progress completes for this screen, and subsequent installati on progress screens open and self-dismiss. The installer completes this portion of the installation, and the system automatically restarts. WARNING: DO NOT REMOVE THE INSTALLA TION CD FROM THE CD-ROM DRIVE.

Once the system completely launches and the W indows desktop displays, a subsequent screen opens for additional installation progress.


An InstallShield Wizard Comp lete screen displays.

16

Ensure that the Yes, I want to restart m y compu ter again radio button is selected.

17

Remove the CD from the CD-ROM drive.

18

Click Finish . The system restarts. FUJIFILM applications launch.

19

Proceed following the installation checklist on page 19; subsequent installations are required.


Printer Selecting the Printer installation setup type installs the printer functionality on an FMPC/LPC computer. Supported printers in this configuration include network and FireW ire printers.

Hardware Associated with this Setup Type This setup type should be selected only when installing on the LPC/FMPC computers associated with the following printers: LP 5000 printer

LP 7600 printer

LP 1500 printer

LP 7000 printer

LP 7700 printer

LP 2000 printer

LP 7100 printer

LP 7900 printer

LP 2500 printer

LP 7200 printer

DL 400 printer

LP 5000 printer

LP 7500 printer

DL 410 printer

LP 5500 printer LP 5700 printer

Note: The DL 430, DL 450, and DL 600 printers are installed via separate printer software.

Note: The printers listed above require FireW ire and VDEntry tasks completed before MS01 installation.


>>> To install Printer only: 1

Before beginning thi s installation , you must compl ete all pre-MS01 installati on tasks referenced in the inst allation checkli st for t his MS01 setup type (page 24).

2

All FireWire drivers must be installed and VDEntry settings must be completed prior to starting this procedure.

3

Insert the MS01 Installation CD into the FMPC’s/LPC’s CD-ROM drive.

4

If the CD does not auto-run the installer, navigate to the CD-ROM drive via the Windows Start > Run or Explorer feature, and double-click the set up. exe file in the EZ171 directory. The software launches, and the Choose Setup Language screen displays.

5


6

Click Next >. A Preparing Setup screen displays and selfdismisses.



7


8

From the drop-down menu, select Printer .

9

Click Next >.


The Setup Type > Please select t ype of p rinter screen displays.

10

From the drop-down menu, select the printer for this configuration.

11

Click Next >. The Setup Type > Disc Writ er Support screen displays.

12

13







Click Next >.


The Setup Type > What type of scanner will this printer be used with? screen displays.

14

Select the type of scanner that will be connected to the LPC/FMPC.

15

Click Next >. The Edit Data > Enter the names of the MS01 & SP systems screen displays. Note: The Scanner field only displays if you are installing the SP 1500, 2000, 2500, and 3000 models.

Note: If you selected None or SP 500 when selecting your scanner type, the Edit Data screen does not display a Scanner field.


16

Enter the names ensuring that they do not exceed 15 characters.

17

Click Next >. The Information screen displays. Note: If an error dialog opens, then a component name has been incorrectly typed into an Edit Data screen, or the ICIII isn’t accessible via the network. Click OK and the Edit Data information that needs to be changed will appear.

18


19

If the information is incorrect, click < Back to navigate to previous selection screens, and modify settings, as appropriate. If the information is correct, ensure that the printer is in StandBy mode and click Next >. The Setup Type > Installing screen displays.


20

If you selected None during scanner model selections, an InstallShield Wizard Complete screen displays. Ensure that the Yes radio button is selected. Click Finish . The system restarts. FUJIFILM applications launch. Proceed following the installation workflow referenced on page 25; subsequent installations are required.

If you are installing an LP 1500/2000/2500 series printer…

If you are installing an LP 7x00 , LP 5000 or DL 4x0 series printer…

If you are installing an LP 5500/5700/5900 series printer…

The InstallShield Wizard > Frontier

An

The status halts and the

Workflow Management Software – InstallShield Wizard dialog box

InstallShield Wizard Complete

InstallShield Wizard > Prin ter Data dialog box opens.

opens informing you that the printer update will run.

screen displays.

Click OK .

Select the No radio button.

Insert the Printer Data diskette into the printer’s floppy drive.

The Please Wait message displays and self-dismisses.

Click Finish .

Click OK .

The status halts and the

Insert the printer software disk into the CD-ROM drive.

The printer reads the floppy data.

Insert the Printer Data diskette into the printer’s floppy drive.


Once the data load has finished, the InstallShield Wizard > Printer Data load fini shed dialog box opens.

Click OK .

Restart the computer.

Remove the floppy diskette from the floppy drive and click OK .

InstallShield Wizard > Printer Data dialog box

opens.


The printer reads the floppy data.

FUJIFILM applications launch.

The InstallShield Wizard > Frontier Workflow Management Software – InstallShield Wizard

dialog box opens informing you that the printer update will run. Once the data load has finished, the InstallShield

Proceed following the installation workflow referenced on page 24; subsequent installations are required.

Wizard > Printer Data load finished dialog box opens.

Click OK .

Remove the floppy diskette from the floppy drive and click OK .

The Please Wait message displays and self-dismisses.

MS01 installation progress continues.

MS01 installation progress continues.

Finally, an InstallShield Wizard Complete screen displays.

Finally, an InstallShield Wizard Complete screen displays.

Ensure that the Yes radio button is selected.


If you are installing an LP 1500, LP 2000, or LP 2500 printer, you must turn the printer power off and then back on using the breaker .


Wait until the Standby or Warming up message appears on the printer operation panel before moving

The system restarts.

to the next step. Remove the CD from the CD-ROM drive.

Click Finish .

FUJIFILM applications launch. Proceed following the installation workflow referenced on page 24; subsequent installations are required.


Click Finish . FUJIFILM applications launch. A printer message may display. Wait for the printer message to self-dismiss. Note: When the message “Printer memory has been updated” appears, click OK to close the message.

Important: Do not turn the printer power off during this process. FUJIFILM applications launch. Proceed following the installation checklist referenced on page 24; subsequent installations are required.


Scanner Selecting the Scanner installation setup type installs the scanner functionality on the SPC/MCU. Supported scanners in this configuration include FireWire scanners only.

IMPORTANT: Verify available dis k space on the SPC/MCU before startin g th is pr ocedure. This task is only required fo r th e certain scanner h ardware models, incl uding : SP 1500, 2000, or 2500. After an SP 1500, 2000, or 2500 system’s SPC/MCU has had the operating system installed, perform tasks to prevent lack-of-space issues (see page 122).

Hardware Associated with this Setup Type Important: The scanner software must be installed before you start the foll owing p rocedure.

This setup type should only be chosen when installing on the computers associated with the following scanners: SLP-800 (tethered only)

SP-2000 scanner

SLP-1000 (tethered only)

SP-2500 scanner

SP-1500 scanner

SP-3000 scanner

>>> To install scanner only: 1

Before beginning thi s installation , you must compl ete all pre-MS01 installati on tasks referenced in th e installation checkli st for t his MS01 setup type (page 25).

2

Before performing this installation, you must have already completed: a. If you are installing on a system configured with the SP3000 scanner, the A1 and MS11 software must both be installed before starting this procedure. b. If you are installing on a system configured with the SP 1500/2000/2500 scanner, o If you plan on using the FrontMan software for film scanning, the A1 and MS11 software must both be installed before starting this procedure. o If you do NOT plan on using the FrontMan software for film scanning, only the A1 software must be installed before starting this procedure.

3

Insert the MS01 Installation CD into the SPC’s/MCU’s CD-ROM drive. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 43

4

Post-op the system.

5

Power on the scanner while holding down the keyboard key (to prevent the scanner software from launching).

6


7


8




9


10

Select Scanner .

11

Click Next >.


The Setup Status > Select Scanner Type screen displays.

12

Select the scanner type in your configuration.

13

Click Next >. The Setup Status > Select FrontMan or No FrontMan screen displays.

14

Select the appropriate option for this lab’s configuration. o Selecting YES will ensure that FrontMan is the software used for film scanning. o Selecting NO will ensure that the A1 and MS11 software are used when film scanning.

15

Click Next >. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 46

The Edit Data > Enter the name of the MS01 system screen displays.

16

Enter the name of the ICIII. Note: Ensure that names do not exceed 15 characters.

17

Click Next >.

18

If this is a tethered system, a screen opens asking if you want to load the printer size table. o Select Yes if you want to load the print size table for the default products loaded by the software. Doing this will overwrite any changes made to the print size table since the last installation. This is the recommended choice. o Select No if you want to manually enter all print sizes that you will want the scanner and printer to process.

Click Next >. A screen displays asking you whether or not you want to user the FrontMan software for film scanning.

19

Select Yes if you want to use the FrontMan software interface when film scanning. Select No if you want to use the A1/S1 software interface when film scanning.

20

Click Next >.


The Information screen displays. Note: You ICIII System Name may differ from the example displayed here. Note: If an error dialog opens, then a component name has been incorrectly typed into an Edit Data screen, or the ICIII is inaccessible via the network. Click OK and the Edit Data information that needs to be changed will appear.

21


22

If the information is incorrect, click < Back to navigate to previous selection screens, and modify settings, as appropriate. If the information is correct, click Next >. The Setup Type > Installing screen displays.


23

Ensure that the Yes, I want to restart m y compu ter again. radio button is selected. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 48

24


25


26

Proceed following the installation workflow checklist on page 25; subsequent installations are required.


MS01 with Print er Support Selecting the MS01 with Printer Suppo rt installation setup type installs the MS01 and printer functionality on the ICIII server. Supported printers in this configuration include network and USB printers. Supported scanners in this configuration include FireWire scanners only.

Hardware Associated with this Setup Type This setup type should be selected only when installing on ICIII computers serving as the LPC/FMPC for the following printers: LP 5000 printer

LP 7700 printer

LP 7000 printer

LP 7900 printer

LP 7100 printer

ASK

LP 7200 printer

DL 400 printer

LP 7500 printer

DL 410 printer

LP 7600 printer



>>> To install MS01 with Printer Support: 1


2

Insert the MS01 Installation CD into the ICIII’s CD-ROM drive.

3


4


5




6


7

Select MS01 with Printer Support .

8

Click Next >.


The Setup Type > Additio nal Securit y screen displays.

9

o

If you want to lock down the system to prevent the end user from accessing the operating system while running the Fuji software (operator mode), select the Add ad di ti on al s ecu ri ty to this system check box.

o

If Ad d ad di ti on al s ecu ri ty t o t hi s s ys tem is not selected, the system runs in Support mode.

2


10

11










Click Next >.

2

The system can be run in two modes: Support or Operator. Support mode allows full-access to the operating system; Operator mode does not. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 53

The Setup Type > Please select type of printer screen displays.

12

From the drop-down menu, select the printer for this configuration. Note: Select None if you will be installed a printer that is installed via separate printer software (such as the DL 430, DL 450, and DL 600).

13

Click Next >. Note: If you selected ASK in the previous screen, a subsequent screen displays the possible ASK models and configurations. Select the option applicable to your ASK configuration, and click Next .


The Setup Type > What type of scanner will this printer be used with? screen displays.

14

Select the type of scanner that will be connected to the MS01 Server.

15

Click Next >. If you selected None, this screen will not appear. Proceed to the next step.

If you selected a scanner model number in the previous step, the Edit Data screen displays.

If necessary, edit the Scanner server name. Note: Ensure that names do not exceed 15 characters.

Click Next >.

The Information screen displays. Note: If an error dialog opens, then a component name has been incorrectly typed into a n Edit Data screen. Click OK and the Edit Data information that needs to be changed will appear.


16

Review the system information displayed in the body of the screen.

17


Once progress completes, several small installation screens open and self-dismiss. The system automatically restarts, and the InstallShield wizard continues with i nstallation.



18

Remove the MS01 Installation CD from the CD-ROM drive. If you are installing an LP 5000 or ASK series printer…

If you are installing an LP 7x000 / DL 4x0 series printer…



Click Finish .

Click Finish . The InstallShield Wizard closes.

The system restarts, and the Windows desktop displays.




A printer message may display. Wait for the printer message to self-dismiss.


When the message “Printer memory has been updated” appears, click OK to close the message.

Important: Do not turn the power-off the printer during this process. 19


20

Proceed following the installation workflow referenced on page 20; subsequent installations are required.


MS01 with Scanner Suppor t Selecting the MS01 with Scanner Suppor t installation setup type installs the MS01 and scanner functionality on the ICIII server. Supported scanners in this configuration include USB scanners only. Printer support should be added via a separate computer.

Hardware Associated with this Setup Type This install ation setup ty pe is only appli cable with an SP 500 scanner; these scanners use the MS01 Server as thei r SPC/MCU compu ter.

>>> To install MS01 with Scanner Support: 1


2


3


4


5

Click Next >.


A Preparing Setup screen displays and selfdismisses.


6



7

Select MS01 with Scanner Suppor t .

8

Click Next >. The Setup Type > Additi onal Security screen displays.

9

o


o

3 If Ad d ad di ti on al sec ur it y t o t hi s s ystem is not selected, the s ystem runs in Support mode.

Click Next >.

3

The system can be run in two modes: Support or Operator. Support mode allows full-access to the operating system; Operator mode does not. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 60

The Setup Type > Disc Wri ter Support screen displays.

10

11










Click Next >. The Edit Data > Enter the name of t he FMPC system screen displays.

12

If necessary, edit the Printer server name field: Note: Ensure that names do not exceed 15 characters.

13

Click Next >.


The Information screen displays. Note: If an error dialog opens, then a component name has been incorrectly typed into an Edit Data screen. Click OK and the Edit Data information that needs to be changed will appear.

14


15


Once progress in the screen completes, several small installation screens open and self-dismiss. The system automatically restarts during installation. WARNING: DO NOT REMOVE THE INSTALLA TION CD FROM THE CD-ROM DRIVE.



16

Ensure that the Yes, I want to restart m y compu ter again. radio button is selected.

17

Remove the MS01 Installation CD and insert the MS11 for SP500 installation CD into the CD-ROM drive.

18

Click Finish . The system restarts.

19

Proceed following the installation checklist referenced on page 21; subsequent installations are required.


MS01 with Print er and Scanner Support Selecting the MS01 with Prin ter and Scanner Support installation setup type installs the MS01, printer, and scanner functionality on the ICIII server. Supported printers in this configuration include network and USB printers. Supported scanners in this configuration include USB scanners only.

Hardware Associated with this Setup Type This inst allation setup type is only applicable with an SP 500 Scanner. SP 500 scanners no lo nger have separate computers (SPCs/MCUs); these scanners now use the MS01 ICIII Server as their SPC/MCU com put er.

This setup type should be chosen when installing on the computers associated with the following printers: LP 5000 printer

LP 7700 printer

LP 7000 printer

LP 7900 printer

LP 7100 printer

ASK

LP 7200 printer

DL 400 printer

LP 7500 printer

DL 410 printer

LP 7600 printer



>>> To install MS01 with Printer and Scanner Support: 1

Before beginning th is ins tallation, you must compl ete all pr e-MS01 installati on tasks referenced in the installation c hecklist f or thi s MS01 setup type (page 22).

2


3


4


5




6


7

Select MS01 with Printer and Scanner Support .

8

Click Next >.


The Setup Type > Additi onal Security screen displays.

9

10

o

If you want to lock down the system to prevent the end user from accessing the operating system while running the Fuji software (operator mode), select the Ad d ad di ti on al s ecu rit y t o t hi s system check box.

o

If Ad d ad di ti on al sec ur it y t o t hi s s ystem is not selected, the system runs in support mode.


11

12










Click Next >.


The Setup Type > Please select type of print er screen displays.

13

From the drop-down menu, select the printer for this configuration. Note: Select None if you will be installed a printer that is installed via separate printer software (such as the DL 430, DL 450, and DL 600).

14

Click Next >. The Information screen displays. Note: If an error dialog opens, then a component name has been incorrectly typed into an Edit Data screen. Click OK and the Edit Data information that needs to be changed will appear.

15


16

If the information is incorrect, click < Back and modify settings, as appropriate. If the information is correct, click Next >.


The Setup Status > Installing screen displays.

Once progress in the screen completes, several small installation screens open and self-dismiss. The system restarts. WARNING: DO NOT REMOVE THE INSTALLA TION CD FROM THE CD-ROM DRIVE.

The InstallShield wizard continues with installation. An InstallShield Wizard Comp lete screen displays.

17

Reference the following instructions based on your hardware configuration.


LP 7x00 / DL 4x0 4x0 + SP 500 500 Scann Scann ers

18

ASK / LP L P 5000 + SP 500 Scan ner s

a

If you are installing a LP 7x00 / DL 4x0series printer with an SP 500 model scanner, an InstallShield Wizard Complete screen displays.

a

If you are installing an ASK or LP 5000 model printer with an SP 500 model scanner, an InstallShield Wizard Complete screen displays.

b

Select the No radio button (so the system does NOT restart).

b

Select the No radio button (so the system does NOT restart).

c

Click Finish . The MS01 installer closes.

c

Click Finish . The MS01 installer closes.

d

Insert the printer’s SDK installation CD and run the installer.

d

Insert the MS11 for SP 500 installation CD and run the installer.

e

Perform all instructions noted during the printer installation.

e

Perform all instructions noted during the scanner installation.

f

Insert the MS11 for SP 500 installation CD and run the installer.

f

Once the scanner installation is complete, restart the system.

g

Perform all instructions noted during the scanner installation.

h

Once the installation is complete, restart the system.

Proceed following the installation checklist referenced on page 22; page 22; subsequent subsequent installations are required.


MS01 MS01 Work Work station stati on Workst ation installation setup type enables Selecting the MS01 Workst you to add additional MS01 workstation computers to the system.

A scanner is not connectable connectable to a workstation.

>>> To install MS01 Workstation: 1

Before beginni beginni ng thi s installation , you must compl ete all pre-MS01 pre-MS01 installatio n tasks referenced referenced in th e installation checkli st for this MS01 MS01 setup type (page 26) (page 26)..

2

Insert the MS01 Installation CD into the ICIII workstation’s CD-ROM drive.

3

If the CD does not auto-run the installer, navigate to the CD-ROM drive via the Windows Start > Run or Explorer feature, up. exe file in the EZ171 directory. feature, and double-click the set up. The software launches, and the Choose Setup Language screen displays.

4


5

Click Next >.


Preparing Setup Setup screen displays and self A Preparing dismisses.


6



7

Select MS01 Workst ation .

8

Click Next >. The Setup Type > Additio nal Securit y screen displays.

9

10

o

If you want to lock down the system to prevent the end user from accessing the operating system while running the Fuji software (operator mode), select the Ad d ad di ti on al s ecu ri ty to this system check box.

o

If Add ad di ti on al s ecu ri ty to th is sy st em is not selected, the system runs in support mode.

Click Next >.


The Setup Type > Disc Writ er Support screen displays.

11

12







Click Next >. The Edit Data > Enter the name of the MS01 syst em screen displays.


13

Review the system information displayed in the body of the screen. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 74

14

If the information is incorrect, click < Back and modify settings, as appropriate. If the information is correct, click Next >. The Setup Type > Installing screen displays.

Once progress in the screen completes, several small installation screens open and self-dismiss . The system restarts. WARNING: DO NOT REMOVE THE INSTAL LA TION CD FROM THE CD-ROM DRIVE, the

InstallShield wizard continues with installation. An InstallShield Wizard Complete screen displays.

15


16


17


18

Proceed following the installation checklist referenced on page 26; subsequent installations are required. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 75

MS01 Workstation with Printer Support Selecting the MS01 Workst ation wit h Printer Support installation setup type installs an additional MS01 workstation computer with added printer support (additional printer). Supported printers in this configuration include network and USB printers.

Hardware Associated with this Setup Type This setup type should be chosen when installing on the computers associated with the following: LP 5000 printer

LP 7700 printer

LP 7000 printer

LP 7900 printer

LP 7100 printer

ASK

LP 7200 printer

DL 400 printer

LP 7500 printer

DL 410 printer

LP 7600 printer


>>> To install MS01 Workstation with Printer S upport: 1

Before beginning thi s installation , you must compl ete all pre-MS01 installati on tasks referenced in the inst allation checkli st for t his MS01 setup type (page 27).

2

Insert the MS01 Installation CD into the ICIII workstation’s CD-ROM drive.

3

If the CD does not auto-run the installer, navigate to the CD-ROM drive via the Windows Start > Run or Explorer feature, and double-click the set up. exe file in the EZ171 directory.


The software launches, and the Choose Setup Language screen displays.

4


5



6

Click Next >.


The Setup Type > Select System Type screen displays.

7

Select MS01 Workstation w ith Print er Support .

8


9

o


o

If Add ad di ti on al sec ur it y t o t hi s s ystem is not selected, the system runs in support mode.


10


11

12







Click Next >. The Setup Type > Please select type of printer screen displays.

13



14

Click Next >. The Edit Data > Enter the name of the MS01 system screen displays.

15

Edit the ICIII server name.

16

Click Next >. The Information screen displays. Note: If an error dialog opens, then a component name has been incorrectly typed into an Edit Data screen. Click OK and the Edit Data information that needs to be changed will appear.

17


18

If the information is incorrect, click < Back and modify settings, as appropriate. If the information is correct, click Next >.


The Setup Type > Installing screen displays.

Once progress in the screen completes, several small installation screens open and self-dismiss. The system restarts. WARNING: DO NOT REMOVE THE INSTALLA TION CD FROM THE CD-ROM DRIVE.

The InstallShield wizard continues with installation. An InstallShield Wizard Comp lete screen displays.

Remove the MS01 Installation CD and insert the printer software installation CD into the CD-ROM drive. 19

If you are installing an LP 5000 or an ASK series printer…

If you are installing an LP 7x00 / DL 4x0 series printer…



Click Finish .

Click Finish .

The system automatically restarts, and the Windows desktop displays.





A printer message may display.


Wait for the printer message to selfdismiss.


Note: When the message “Printer memory has been updated” appears, click OK to OK to close the message.

Important: Do not turn the printer power off during this process. 20

Proceed following the installation checklist referenced on page 27; page 27; subsequent subsequent installations are required.


MS01 Server with Tethered Printer This is a legacy c onfiguration where the printer and scanner are connected to each other via F ireWire. The scanner is connected to the ICIII via network connection.

Hardware Associated with this Setup Type This setup type should be chosen when installing on the computer associated with the following: SLP 800 scanner/printer

LP 2500 printer

SLP 1000 scanner/printer

LP 5500 printer

LP 1500 printer

LP 5700 printer

LP 2000 printer

LP 5900 printer

>>> To install MS01 with Tethered Printer: 1

Before beginni beginni ng thi s installation , you must compl ete all pre-MS01 pre-MS01 installatio n tasks referenced referenced in th e installation checkli st for t his MS01 setup type (page 23) (page 23)..

2

Insert the MS01 Installation CD into the ICIII server’s CD-ROM drive.

3

If the CD does not auto-run the installer, navigate to the CD-ROM drive via the Windows Start > Run or Explorer feature, feature, and double-click the set up. up. exe exe file in the EZ171 directory.


The software launches, and the Choose Setup Setup Language screen displays.

4


5

Click Next >. Preparing Setup Setup screen displays and self A Preparing dismisses.

Setup Language screen closes, The Choose Setup and the InstallShield Wizard launches, using the selected language.

6

Click Next >.


The Setup Type > Select System Type screen displays.

7

Select MS01 Server with Tethered Printer .

8


o

If you want to lock down the system to prevent the end user from accessing the operating system while running the Fuji software (operator mode), select the Add ad di ti on al security to this system check box.

o

If Add ad di ti on al s ecu ri ty to th is sy st em is not selected, the system runs in support mode.


9


10

11










Click Next >. The Setup Type > Please select type of tethered printer screen displays.

12


13

Click Next >.


14

If you selected an SLP model, proceed below.

If you selected an LP model, the Setup Type > select scanner screen displays.

Select the appropriate scanner model. Click Next >. An Edit Data screen displays.

15

Enter the scanner’s name in the Scanner field.

16

Click Next >.



17


18

If the information is incorrect, click < Back and modify settings, as appropriate. If the information is correct, click Next >. The Setup Type > Installing screen displays.


19



20


21

Click Finish . The system restarts, and the Windows desktop displays.

22

Proceed following the installation checklist referenced on page 23; subsequent installations are required.


Cancelling Installation You can cancel the installation via the Cancel button on the Installation Wizard up until the point the installer begins to copy files onto the system. 1

After invoking cancellation, an Exit Setup dialog box opens.

2

Click Yes . If cancellation was invoked from the Choose Setup Language screen, the Preparing Setup screen, or after the auto-restart that occurs during the installation process, the installer simply closes.

If cancellation was selected from the Welcome screen or any other screen before the auto-restart that occurs during installation, an InstallShield Wizard Complete screen displays informing you that the software has not been installed.

Click Finish . The InstallShield Wizard closes, and installation is cancelled.


A p p en d i x A : A d d i t i o n al M MS01 T Tas k s VDEntry & 1394 Fir ewire Setup This task is only required for the certain hardware devices, includi ng: LP 1500, 2000, 2500, 5500, 5700, 5900 printers and the SP 1500, 2000, 2500, and 3000 scanners.

Preparation of FireWire Cards and Drivers If you are installing only a FireWire film scanner to the MS01 Server or Printer Server 4 , perform the following: If there is a FireWire card in the ICIII, write down which port the scanner FireWire cable is connected to, then disconnect the cable. If there is no FireWire card installed in the ICIII, refer to page 93. •

•

•

•

Install FireWire drivers on the ICIII Server: o

Windows XP – Refer to page 96.

o

Windows 7 – Refer to page 106.

If using an SP 3000 film scanner: o


o


If using an SP 1500, SP 2000 or SP 2500 film scanner, refer to page Error! Bookmark not defined.. For: o

Windows XP: Disabling FireWire Networking for the SP 1500/2000/2500/3000 Scanners, refer to page 105.

o

Windows 7: Disabling FireWire Networking for the SP 1500/2000/2500/3000 Scanner, refer to page 113.

If you are installing only a FireWire scanner and printer connected to the printer server 5 , perform the following: If there are FireWire cards in the Printer Server, write down which port the scanner FireWire cable is connected to, write down which port the printer FireWire cable is connected to, then disconnect both cables. If there are no FireWire cards installed in the Printer Server, refer to page 93. •

Install FireWire drivers on the Printer Server. Refer to page 96.

•

If using an SP 3000 film scanner:

4

If you are installing an MS01+Printer system with an SP1500, SP2000, SP2500 or SP3000 film scanner, there must be a single FireWire card in the ICIII server. 5 If you are installing a Frontier Manager system with an ICIII Server, Printer Server (also known as LPC or FMPC), SP1500, SP2000, SP2500 or SP3000 fi lm scanner and LP1500, LP2000, LP2500, LP5500, LP5700 or LP5900 printer, there must be two separate FireWire cards in the Printer Server. One FireWire card connects to the film scanner, and the other one connects to the printer. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 91

o


o


•

If using an SP 1500, SP 2000 or SP 2500 film scanner, refer to page 104.

•

If using an LP5500, LP5700 or LP5900 printer, refer to LP5500, LP5700 or LP5900 Printer on:

•

•

o


o

Windows 7 – Refer to page

If using an LP1500, LP2000 or LP2500 printer, refer to LP1500, LP2000 or LP2500 Printer on page 99. For: o


o


If you are installing a FireWire scanner connected to the printer server 6 , perform the following: •

•

•

•

•

•

If there is a FireWire card in the Printer Server, write down which port the scanner FireWire cable is connected to, then disconnect the cable. If there is no FireWire card installed in the Printer Server, refer to Installing One FireWire Card in the Printer Server. Refer to page 93. Install FireWire drivers on the Printer Server. Refer to page 96. If using an SP 3000 film scanner: refer to Setting Up Drivers for an SP 3000 Film Scanner. Refer to page 102. o


o


If using an SP 1500, SP 2000 or SP 2500 film scanner. Refer to page 104. For o


o


If you are installing a FireWire printer connected to the printer server 7 , perform the following: •

If there is a FireWire card in the Printer Server, write down which port the scanner FireWire cable is connected to, then disconnect the cable.

6

If you are installing a Frontier Manager system with an ICIII Server, Printer Server (also known as LPC or FMPC) and SP1500, SP2000, SP2500 or SP3000 film scanner and ARE NOT USING an LP1500, LP2000, LP2500, LP5500, LP5700 or LP5900 printer, there must be a single FireWire card in the Printer Server. 7

If you are installing a Printer system with an LP1500, LP2000, LP2500, LP5500, LP5700 or LP5900, and either no film scanner will be installed or an SP500 film scanner will be connected to the ICIII, there must be a single FireWire card in the Printer server. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 92

•

If there is no FireWire card installed in the Printer Server, refer to Installing One FireWire Card in the Printer Server. Refer to page 93.

•

Install FireWire drivers on the Printer Server. Refer to page 96.

•

If using an LP5500, LP5700 or LP5900 printer on:

•

o


o


If using an LP1500, LP2000 or LP2500 printer, refer to page Error! Bookmark not defined..

FireWire Card Installation Installing a Single FireWire Card in the MS01 Server or Printer Server Please make sure that you follow these procedures exactly.

>>> To install a FireWire card: 1

Remove any media from the computer’s drives (i.e., disks, CDs, and tapes).

2

Turn off all attached devices.

3

Turn off the computer.

4

Unplug all power cords from the electrical outlets.

5

Disconnect all cables attached to the computer.

6

Locate the service manual for the ICIII computer.

7

Follow the instructions in the service manual to open the computer’s case.

8

Locate a single open PCI slot in the computer.

9

Follow the instructions in the service manual to install the FireWire card in the open PCI slot.

10

Write down that the adapter is FireWire Card #1. It will be used for the Scanner (SP).

11

Follow the instructions in the service manual to close the computer’s case.

12

Proceed to “Installing the FireWire Drivers on the ICIII or Printer Server”.

Installing Two FireWire Cards in the Printer Server Please make sure that you follow these procedures exactly.

>>> To install two FireWire cards: 1

Remove any media from the computer’s drives (i.e., disks, CDs, and tapes).

2

Turn off all attached devices.


3

Turn off the computer.

4

Unplug all power cords from the electrical outlets.

5

Disconnect all cables attached to the computer, including power cords, input/output (I/O) cables, and any other connected cables.

6

Locate the service manual for the Printer server computer.

7

Follow the instructions in the service manual to open the computer’s case.

8

Locate two open PCI slots in the computer.

9

Determine whether the PCI slots are located on a riser card. See the following image for an example of PCI slots on a riser card.

If the PCI slots are on a riser card, refer to the following diagram to identify the FireWire cards. FireWire card #1 will be at the top of the riser card.


If the PCI slots are not on a riser card, they are directly on the com puter’s motherboard. Refer to one of the following diagrams to identify the FireWire cards. FireWire card #1 will be closest to the CPU, memory and other motherboard components. FireWire card #2 will be closest to the bottom edge of the motherboard.

If there are more than two PCI slots, the above guideli nes still apply.

Regardless of where the FireWire cards are installed, the cards will always be identified as cards #1 and #2.

10

Follow the instructions in the service manual to install FireWire cards in two open PCI slots.

11

Write down which adapter is FireWire Card #1. It will be used for the Scanner (SP).

12

Write down which adapter is FireWire Card #2. It will be used for the Printer (LP).

13

Follow the instructions in the service manual to close the computer’s case.

14

Proceed to FireWire – Driver Installation below.


FireWire – Driver Installation and Network Configurations For instructions on installing the FireWire Drivers and performing network configuration tasks on the ICIII or Printer Server for: 

Windows XP Systems – See the instructions starting on page 97.



Windows 7 Systems – See the instructions starting on page 106.


Windows XP FireWire Driver Installation and Network Configurations Windows XP: Installi ng th e FireWire Drivers o n the ICIII or Print er Server

Important: Always install the FireWire drivers on the computer that has the FireWire cards installed. 1

After Windows launches, insert the MS Installation CD into the server’s CD-ROM drive.

2

Select Start > Run . The Run dialog box opens.

3

Click Browse. The Browse dialog box opens.

4

Navigate to the server’s CD drive (X represents the CD drive letter) and open directories to the following path: X:\ EZ171\FMPC XP Drivers\EZ171\

5

Select the set up. exe file, and click Open . The filename and path are populated in the Open field of the Run dialog box.

6

Click OK . The Run dialog box closes, and the Device Drivers Disk [D-01] dialog box opens.

7

Click OK . The Device Drivers Disk [D-02] dialog box opens.

8

Click OK .

9

Remove the CD from the CD-ROM drive. The system reboots.


Windows XP: Setting Up FireWire Drivers for LP 5500, LP 5700 or LP 5900 Printer Client Device

1

Ensure that the printer is turned off.

2

Connect the printer’s FireWire cable to the Printer Server’s FireWire Card #2.

3

Turn the printer switch to ON. Wait for the LCD screen to display Frontier…

4

Move the printer switch to STANDBY .

5

Wait until the LCD displays STAND BY. A Welcom e to the Found New Hardware Wizard screen displays on the Printer Server.

6

Select Install the soft ware automatically (Recommended).

7

Click Next . The Completing th e Found New Hardware Wizard screen displays.

8

Click Finish . The wizard closes. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 98

Windo ws XP: Setti ng t he LP 5500, LP 5700 or L P 5900 Fir eWire Interface IP Addr ess

1

On the Printer Server, select Start > Settings > Network Connection s . The Network Connections window opens.

2

Disconnect the printer’s FireWire cable from the back of the Printer Server. Note which port it is connected to.

3

Notice that one of the 1394 Connections has changed to status Network Cable Unplugged . (This is the printer’s FireWire connection.)

4

Right-click the 1394 Connection that is still listed as connected. (This is the scanner’s FireWire connection.)


A context menu opens. (The scanner does not use the networking capabilities of FireWire, and must be disabled to allow the scanner to connect.)

5

Select Disable. Note: Disabling the connection takes a few seconds. The screen may need to be manually refreshed to reflect the disabled connection.

6

Right-click the “unplugged” connection that is listed. A context menu opens.

7

Select Properties . The 1394 Connection Properties dialog box opens.


8

In the Internet Prot ocol (TCP/IP) Properties section, select Internet Protocol (TCP/IP).

9

Click the Properties button. The Internet Protocol (TCP/IP) Properties dialog box opens.

10

11

Select Use the followin g IP address and enter the following: IP address:

192.168.0.10

Subnet mask:

255.255.255.0

Click OK . The Internet Protocol (TCP/IP) Properties dialog box closes, and the 1394 Connection 2 Properties dialog box returns to focus. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 101

12

Click Close. The Properties dialog box closes.

13

Re-connect the printer’s FireWire cable to the port it was unplugged from.

14

Click

to close the window.

Windows XP: Setting Up FireWire Drivers for an SP 3000 Film Scanner

Make sure that you follow these procedures exactly. 1

Ensure that the SP 3000 film scanner is turned off.

2

Complete the scanner installation process.

3

Important: This procedure must be completed before running the vdentry application. Examine the computer and determine if there is a built-in FireWire interface. If there is a built-in FireWire interface, one or more FireWire ports will appear o n the exterior of the computer’s case. •

The ports may be labeled 1394, IEEE 1394, iLink or FireWire.

•

The ports may be labeled with the FireWire symbol:

See the images below for examples of built-i n FireWire ports.

4

If there is not a built-in FireWire interface, the newly added film scanner FireWire board has a BusID of 0. If there is a built-in FireWire interface, the newly added film scanner FireWire board has a BusID of 1.

Next, run the vdentry application to install virtual device drivers . . . 5

From Windows, select Start > Run .


The Run dialog box opens.

6

Type VDEntry in the Open field.

7

Click OK . The VirtualDriverEntry dialog box opens.

8

Set the IEEE1394 BusID to 0.

9

Click Regist . Note: If no error messages appear, the vdentry registration was successful. The Welcome to th e Found New Hardware Wizard screen displays.

10


11

Click Next .


The Completing t he Found New Hardware Wizard screen displays.

12

Click Finish . The wizard closes.

13

Continue installation on the next page with the Windows XP: Disabling FireWire Networking f or th e SP 1500/2000/2500/3000 Scanner s section.

Windo ws XP: Setti ng Up Fir eWire Drivers for an SP 1500, SP 2000 or SP 2500 Film Scanner


Ensure that the SP1500, SP2000 or SP2500 film scanner is turned off.

2


3

Turn on the SP1500, SP2000 or SP2500 film scanner and wait for it to boot.

4

Switch to the computer where the scanner’s FireWire cable is connected (Printer Server or ICIII Server). The Welcome t o th e Found New Hardware Wizard screen displays.

5


6

Click Next .


The Completing the Found New Hardware Wizard screen displays.

7


8

Continue installation on the next page with the Disabling FireWire Networking for the SP 1500/2000/2500/3000 Scanners below.

Windows XP: Disabling FireWire Networking for the SP 1500/2000/2500/3000 Scanners

Note: Only perform these steps on systems without LP 5500/5700/5900 printers; follow the steps on page 99 for these systems. 1

On the Printer Server, select Start > Settings > Network Connection s . The Network Connections window opens.

2

Right-click the first 1394 Connection that is listed.


A context menu opens.

3

Select Disable. Note: Disabling the connection takes a few seconds. The screen may need to be manually refreshed to reflect the disabled connection.

4

Repeat steps 2 and 3 above for each 1394 connection in your system.

Windows 7 FireWire Driver Installation and Network Configurations Windows 7: Installing t he FireWire Drivers on the ICIII or Printer Server

Important: Always install the FireWire drivers on the computer that has the FireWire cards installed. 1

Turn on the computer.

2

After Windows launches, insert the MS Installation CD into the server’s CD-ROM drive.

3

Press the [Windows ] + [R] keys. The Run dialog box opens.

4

Click the Browse… button. The Browse dialog box opens.

5

Navigate to the server’s CD drive (X represents the CD drive letter) and open directories to the MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 106

following path: 



6

Using an SP 2000 film scanner: X: \ EZ171\ FMPC W7 Dr i ver s\ I nst al l \ EZ171\ Using an SP 3000 film scanner: X: \ EZ171\ FMPC\ EZ171\ SP3000I nst al l \ EZ171\

Select the set up. exe file and click the Open button. The Run dialog box returns to focus. The Open field is populated with the path to the set up. exe file.

7

Click OK . The Run dialog box closes and the Device Drivers Disk[D- 01] dialog box opens.

8

Click OK . A Windows Security dialog box opens.

9

Click Install this driv er software anyway . The Device Drivers Disk[D- 02] dialog box opens.

10

Click OK .

11

Remove the CD from the CD-ROM drive. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 107

The system reboots. 12

Turn the printer switch to the ON position.

Windo ws 7: Setti ng t he LP 5500, LP 5700 or L P 5900 FireWire Int erface IP Addr ess

1

On the Printer Server, select Start > Control Panel .

The Windows Control Panel displays.

2

Select Netwo rk and Internet > View netwo rk status and t asks.


The Networ k and Sharing Center window opens.

3

Click Change adapter settin gs .

The Network Connections window opens. Note: This is only an example (right), the proper configuration is:

4



LocalAreaConnection2: Scanner



LocalAreaConnection3: Printer

Right-click the Loc al Area Connect ion x IP Over 1394 #2 connection that is still listed as connected (this is the scanner’s FireWire connection). A context menu opens.

Note: The scanner does not use the networking capabi lities of FireWire and must be disabled to allow the scanner to connect.


5

Select Disable.

6

Right-click the Local Area Connection x IP Over 1394 connection that is still listed as connected. A context menu opens.

7

Select Properties .

The Local Area Connection x Properties dialog box opens.

8

From the This connection uses the following items list, select Internet Protocol Version 4 (TCP/IPv4).

9

Click the Properties button.


The Internet Protocol Version 4 (TCP/IPv4) Pro pert ies dialog box opens.

10

Select the Use the followin g IP address radio button and enter the following information in the corresponding fields: 



11

IP address: 192.168.0.10 Subnet mask: 255.255.255.0

Click OK . The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box closes and the Local Area Connection x Properties dialog box returns to focus.

12

Click OK . The Local Area Connection x Properties dialog box closes and the Network Connections window returns to focus.

13

Re-connect the printer’s FireWire cable to the port from which it was previously disconnected.

14

Click the

button to close the Network Connections window.

Windows 7: Settin g Up FireWire Drivers f or an SP 3000 Film Scanner


Ensure that the SP 3000 film scanner is turned off.

2



3

Important: This procedure must be completed before running the vdentry application. Examine the computer and determine if there is a built-in FireWire interface. If there is a built-in FireWire interface, one or more FireWire ports will appear o n the exterior of the computer’s case. •

The ports may be labeled 1394, IEEE 1394, iLink or FireWire.

•

The ports may be labeled with the FireWire symbol:

See the images below for examples of built-in FireWire ports.

4

If there is not a built-in FireWire interface, the newly added film scanner FireWire board has a BusID of 0. If there is a built-in FireW ire interface, the newly added film scanner FireWire board has a BusID of 1.

Next, run the vdentry application to install virtual device drivers . . . 5

From Windows, select Start > Search programs and files field and type VDEntry .

6

Press the key.


The VirtualDriverEntry dialog box opens.

7

Set the IEEE1394 BusID to 0.

8

Ensure the UnRegist check-box is no t selected.

9

Click Regist. Note: If no error messages display, the VDEntry registration was successful.

10

Click Close.

Windows 7: Disabling FireWire Networking for the SP 1500/2000/2500/3000 Scanner

Note: Only perform these steps on systems without LP 5500/5700/5900 printers. 1

On the Printer Server, select Start > Control Panel Panel .


The Windows Control Panel displays.

2

Networ k and Internet > View View Select Networ network status and tasks . Networ k and Sharing Center Center The Networ window opens.

3

adapter settin gs . Click Change adapter


The Network Connections window opens.

4

1394 #2 #2 connection that is still listed as connected Right-click the Loc al Area Connect ion x IP Over 1394 (this is the scanner’s FireWire connection).

A context menu opens. opens.

Note: The scanner does not use the networking capabilities of FireWire and must be disabled to allow the scanner to connect. 5

Select Disable. Note: Disabling the connection takes a few seconds. T he screen may need to be manually refreshed to reflect the disabled connection.

6

Repeat steps 4 and 5 for each e ach 1394 connection in your system.

7

Click the

button to close the Network Connections window.


Adjusting the System’ s Date and Time Properties Verify the date and time on each PC in your system before software installation: For PCs running Windows XP: See the instructions starting on this page. For PCs running Windows 7: See the instructions starting on page .

Window s XP – Date and Time Properties 1

In the Windows taskbar’s system tray, double-click the clock icon in the bottom right corner. The Date and Time Properties dialog box opens.

2

Click the Time Zone tab if the displayed time zone is incorrect.

3

Adjust, as necessary.


4

Click Appl y to retain changes.

5

Click the Date & Time tab to adjust today’s date on the calendar if the date displayed is incorrect.

6

Use the Time interface to adjust the time.

7

Click Ap pl y to retain changes.

8

Click OK . Date and time settings are updated, and the dialog box closes.

Window s 7 – Date and Time Prop erties 1

From the Windows Start Menu, click Control Panel .

The Windows Control Panel opens.

2

Click Date and Time.


The Date and Time dialog box opens.

3

Ensure the correct Time zone is displayed.

4

If the Time zone displayed is: 



Correct, move on to step 8. Incorrect, continue to the next step.


5

Click the Change time zone… button.

The Time Zone Settings dialog box opens.

6

Select the appropriate option from the Time zone drop-down menu. Note: If the region observes Daylight Saving Time, ensure the Au to mat ical ly adj us t c lo ck fo r Daylight Saving Time check-box is selected.

7

Click OK . The Date and Tim e dialog box returns to focus.


8

If the information displayed for the Date and Time is: 



9

Correct, skip to step 14. Incorrect, proceed to the next step.

Click the Change date and time… button.


The Date and Time Settings dialog box opens.

10

Select the correct Date: 



Select the correct month using the back and forward arrows on the calendar. Select the correct day by selecting it on the calendar.

11

Use the spin controls under the clock to adjust the Time.

12

Click OK .


The Date and Time dialog box returns to focus, displaying the updated date and time.

13

Click the Ap pl y button.

14

Click OK . Date and time settings are updated, and the dialog box closes.

Ensur ing Adequate SPC/MCU Disk Space This task is only required for the certain scanner hardware models, inc luding: SP 1500, 2000, or 2500. After an SP 1500, 2000, or 2500 system’s SPC/MCU has had the operating system installed, perform the following tasks to prevent lack-of-space issues.

>>> First, move some directories on the SPC/MCU 1

Open a Windows Explorer window, and browse to the C: \ drive.

2

Select both the I386 directory and the Drvlib directory, and right-click. A context menu opens.

3

Select Cut . The directories and their contents are placed on the Windows clipboard.

4

Browse to the D: \ drive.

5

Right-click anywhere in the window. A context menu opens.

6

Select Paste.


The directories are pasted into the D: \ drive. 7

Close all Windows.

>>> Second, reconfigure the pagefile size on the SPC/MCU 8

On the desktop of SPC/MCU, right-click the My Computer icon. A context menu opens.

9

Select Properties . A System Properties dialog box opens.

10

Select the Performance tab.


The Performance tab displays.

11

Click the Change button. A Virtual Memory dialog box opens.

12

Ensure that the C: drive is selected in the Drive (Volume Label) list box.

13

Make the following changes: In the Initial Size (MB) field, change the value to 383 In the Maximum Size (MB) field, change the value to 383

14

Click the Set button.


The new settings for the C: drive are saved, a nd the Drive (Volume Label) list box is updated. 15

Now, select the D: drive in the Drive (Volume Label) list box.

16

Make the following changes: In the Initial Size (MB) field, change the value to 700 In the Maximum Size (MB) field, change the value to 700

17

Click the Set button. The new settings for the D: drive are saved, a nd the Drive (Volume Label) list box is updated.

18

Click OK . The Virtual Memory dialog box closes, and focus returns to the System Properties dialog box.

19

Click OK . The System Properties dialog box closes.

20

Reboot the SPC/MCU. The SPC/MCU system is now ready to install the scanner (also call ed A1) and MS01 software.


Installi ng & Con figur ing the ASK 2000, 4000, & 4000A Printers Once the MS01 software has been installed, the next step is to install the ASK printers. This is a two-step process: 1. Install the ASK printers and o

Windows XP: run the W indows-standard Found New Hardware wizard. See page 127.

o

Windows 7: manually setup printer drivers. See page 130.

2. Configure the printers to properly coordinate with the USB ports that the printers are plugged into on the ICIII CPU. See page 136. Based on your system’s configuration, the printers must be installed in the particular order defined in the table below. Install First

Install Second

Install Third

Install Fourth

Configurations

Printer

Size

USB#

Printer

Size

USB#

Printer

Size

USB#

2-4x6 _1-8x10

ASK2000

4x6

2

ASK2000

4x6

1

ASK4000

8x10

0

2-4x6_1-5x7

ASK2000

4x6

2

ASK2000

4x6

1

ASK2000

5x7

0

2-6x9 _1-8x10

ASK2000

6x9

2

ASK2000

6x9

1

ASK4000

8x10

0

1-4x6_1-6x9_1-8x10

ASK2000

6x9

2

ASK2000

4x6

1

ASK4000

8x10

0

1-4x6_1-5x7_1-8x10

ASK2000

5x7

2

ASK2000

4x6

1

ASK4000

8x10

0

2-3.5x5_1-A4*

ASK2000

3.5x5

2

ASK2000

3.5x5

1

ASK4000A

A4

0

1-3.5x5_ 1-5x7_1-A4 A4*

ASK2000

3.5x5

1

ASK2000

5x7

2

ASK4000A

A4

0

2-4x6_1-5x7_1-8x12

ASK2000

5x7

3

ASK2000

4x6

2

ASK2000

4x6

2-4x6_1-6x9_1-8x12

ASK2000

6x9

3

ASK2000

4x6

2

ASK2000

4x6

* Non-US configurations only


Printer

Size

USB#

1

ASK4000

8x12

0

1

ASK4000

8x12

0

ASK Hardware Instal lat ion & Conf igu rat ion Windows XP – Install ASK Printer Drivers

1

Ensure that all of the printers are turned off.

2

Plug each printer’s USB cable into the ICIII.

3

Referring to the configuration chart at the beginning of this chapter, turn on the first printer in your configuration. A Found New Hardware Wizard opens.

4

Select the Install from a list or specific location (Adv anced) radio button.

5

Click Next .


The Please choose you r search and installation options screen displays.

6

Select the Search for the best driver in these locations radio button.

7

Select the Include this loc ation in the search check box.

8

In the associated field, type C:\DRIVERS\Copal\Drivers.

9

Click Next . Hardware installation progress displays.


A Hardware Installation dialog box displays.

10

Click Continue Anyway . The Completing th e Found New Hardware Wizard screen displays.

11


12

Once all ASK printer drivers are installed move on to the Configure ASK Print er USB Ports section on page 136.


Windows 7 – Install ASK Printer Drivers

1

From the Windows Start Menu, click Control Panel .

The Windows Control Panel opens.

2

Click Hardware and Sound .


The Hardware and Sound window displays.

3

Under the Devices and Printers group, click Device Manager .


The Device Manager window opens.

4

Click the arrow corresponding to Other devices to expand the contents of options in the list.

5

Right-click the first printer in the Other Devices list to display a context menu.

6

From the context menu, select Update Driver Software…


An Update Driver Softw are – [Printer Name] dialog box opens.

7

Click Browse my computer for driver software. The dialog box updates, displaying a Search for dri ver softw are in this location field.

8

Click the Browse… button.


A Brows e For Folder dialog box opens.

9

Navigate to the Copal Drivers folder.

10

Select the Copal Drivers folder and click OK . The Update Driver Software – [Printer Name] dialog box returns to focus, displaying the path to the Copal Drivers folder.

11

Click Next . A Windows Security dialog box opens.


12

Click Install this dri ver softw are anyway. The Windows Security dialog box closes and the Update Driver Software – [Print er Name] dialog box returns to focus, indicating that the driver software is being installed.

After a few moments, the dialog box updates, indicating the driver installation is complete.

13

Click Close. The Device Manager window returns to focus.


14 15

Repeat steps 5 – 13 until all ASK printer drivers are installed. Once all ASK printer drivers are installed move on to the next section - Configur e ASK Printer USB Ports .

Configure ASK Printer USB Ports

1

From Windows, select Start > Run . The Windows-standard Run dialog box opens.

2

In the Open field, type C:\FES\ASKTool.exe

3

Click OK . After a few moments, the ASK Too l application window opens.

4

In the list box, select the ASK-2000 item that you just added. It will have a USB No. of 0.

5

Click the Set USB No . button.


The Set New USB No. dialog box opens.

6

In the Please set new USB field, enter the number that corresponds to t he printer in the USB # configuration chart at the beginning of this chapter.

7

Click OK . The Set New USB No. dialog box closes, and focus returns to the ASK Too l application window. The USB No. displayed in the ASK Too l application window for the selected printer updates.

8

Click Exit . The ASK Too l application window closes.

9

10

Repeat the above new hardware installation and USB number confi guration p rocedures for each remaining ASK pr inter based on the order list ed in the table at the beginning of thi s chapter.

After all ASK printers in your system have been installed and configured, select Start > Shut Down . The Shut Down Windows dialog box opens.

11

From the drop-down menu, select Restart .

12

Click OK . The system restarts and is ready to use.


To Back Up (Save) Settings You can save system configuration settings via MS01’s Backup and Restore tool. The data is saved to the specified output directory and an XML file. T his file is used to restore the data. Use this backup procedure to move this data to another system or to restore a system. WARNING: You must perform a new backup anytime the s ystem’s configuration settings have been

changed. 1

In the MS01 Maintenance application, navigate to 02 System Setti ngs > 0215 Backup and Restore.

The Data Backup and Restore dialog box opens.

2

Configure the backup information as desired using the options displayed on the Backup tab.


3

Click Save. A Copying dialog box opens displaying backup progress.

After copying completes, a Data Backup and Restore dialog box opens confirming that the backup is complete.

4

Click OK . The dialog box closes, and focus returns to the main Data Backup and Restore dialog box.

5

Click Close. The Data Backup and Restore dialog box closes.


A p p en d i x B B : IIn f o r m at i o n a ab o u t M MS01 Power for the MS01 System Non-Connected Systems 8 If the lab does not have a connected system, power off all devices nightl y using the established shut down procedures as defined in the MS01 3.0 Start-up and Shut down Guide. Important: Do not shut down the ICIII without first post-op’ing printers and scanners configured with the system. Proper shut down requires post-op of these devices prior t o clicking the exclamation mark bu tton on t he MS01 interface.

Connected Systems Not all hardware components in a FUJIFILM retail lab system should be shut-down nightly. Use the following guidelines to ensure that your lab system’s components run properly. 9

Never Power Off

Power Off Nightly

ICIII CPU (formerly known as the PIC)

FUJIFILM Inkjet printer(s)

Kiosks

RIP CPU associated with the inkjet printers

Xerox Phaser Printer

Epson Wide Format Printer

Rimage CD Writer/Printers

FUJIFILM Film Scanner

Frontier Manager Printer Controller (FMPC/LPC)

FUJIFILM Frontier Printer

8

Non-connected systems have no Internet connectivity and no communication to outside networks. A connected MS01 system is a system that receives data from FUJIFILM’s fullfilment network, sends data to FUJIFILM’s fullfilment network, and receives orders from various sources (such as retailers’ photo Web sites). This is all accomplished via Internet connectivity. 9 These devices should only be powered off for necessary maintenance. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 140

Support Mode Throughout this guide, you will find that many procedures require you to be in Support mode. Support mode enables you to access additional features of the operating system that Operator mode does not allow you to access. Getting into Support mode is a four-step process. Rather than repeating these four steps (with the accompanying descriptive screen captures) in every location where Support mode is required, we show those steps here and refer to this area when Support mode is mentioned in the rest of the guide.

To enter Support mode: 1

From the MS01 4.0 FUJI -- View Orders screen, click Tools in the top right corner.

The MS01 Setup dialog box opens.

2

Click LOG OFF. The Fujifilm L og-Off dialog box opens.

3

Enter the password 5u990rtm0d3 .

4

Click OK .


The system automatically logs off and logs back on. This takes a minute or two. Some Windows screens appear and self-dismiss during the process. The MS01 4.0 FUJI – View Orders screen returns to focus and the system is now in Support mode.


Operator Mode Throughout this guide, you will find that many procedures require you to be in Operator mode. Getting into Operator mode is a four-step process. Rather than repeating these four steps (with the accompanying descriptive screen captures) in every location where Operator mode is required, we show those steps here and refer to this area when Operator mode is mentioned in the rest of the guide.

To enter Operator mode: 1

From MS01 4.0 -- View Orders , click Tools .

The MS01 dialog box opens.

2

Click LOG OFF. The FUJIFILM Log-off dialog box opens.

3

Type the password: operator .

4

Click OK . The system automatically logs off and logs back on. This may take a couple minutes. Some Windows screens display and self-dismiss during the process.


From MS01 4.0 FUJI -- View Orders screen returns to focus and the system is now in Operator mode.


Accessing Maintenanc e 10 Many of the procedural instructions in this g uide require the operator to launch the Maintenance application. Note: SPCs do not display a SwLauncher. You will have t o press to access Maintenance on these computers.

To launch Maintenance: 1

Ensure that the View Orders or View Images screen is displayed.

2

If necessary, click the SwLauncher button.

The SwLauncher application expands. 3

Click the Maintenance button.

The Maintenance application window opens.

10

Note: Not all labs have access to the Maintenance application. For instance, if a lab is set-up in a “locked-down” mode, Maintenance will not be accessible unl ess the system is in Support mode. MS01 Installation Guide © 2006-2011 FUJIFILM Corporation. All rights reserved. 145

PP3-A1425E

Recommend Documents