OWNER
EPC CONTRACTOR
NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KUWAIT OIL COMPANY (K.S.C.) A Subsidiary of Kuwait Petroleum Corporation
COMMENT RESOLUTION SHEET DOCUMENT NO. 50489-530-051-SPC-1002
CONTRACT NO.: 14050489 PROJECT NO.: EF1902
VALVE MATERIAL SPECIFICATION
Company DTN Reference:TRANS-EF1902-AMEC-RTS-000267 Sr. No.
Rev
Company Comment
B
DATE :
Page 1 of 6 17-Jan-15
Company DTN Date: 11-Dec-14
L&T Response To have interchangeability of usage under different service conditions, we shall be procuring valves with only Primer Coating (Inorganic Zinc Silicate) applied. Finish paint of these valves shall be carried out after installation.
1
Contractor shall indicate the applicable standards and project specifications for painting and the painting system on all data sheets
2
SOUR SERVICE REQUIREMENTS- Reference to, and use of guideline for material selection for NACE MR 0175 / ISO 15156 in Appendix ll of KOC-MP-010 shall be made.
Noted and complied.
3
Weld overlay of CRA shall be compliant with section 8.6 of KOC-MP-010.The minimum weld overlay thickness after machining is 3mm.The required CRA deposit shall be achieved through a minimum of three (3) passes. Data sheets to state these requirements, where applicable.
Noted and complied.
4
Flange insulation kit shall be provided for joints where there are dissimilar metals, to avoid galvanic corrosion. Contractor to make note of this requirement in data sheet
There are no such cases of Dissimilar Metal joints in valves as per Valve Material Specifications. Hence there is no requirement for flange insulation kit in valves.
5
Valves for Piping Class N10B / N30B have not been included in this specification. Please provide data sheets for these. There are valves in these piping classes featured on P&IDsBasis for Rejection
Noted and complied
Inorganic zinc silicate has compatibility with paint systems applicable for different service conditions in the project. Hence the same is in compliance with KOC-P-001 ( KOC Standard for painting and coating on metal surface )
Company Confirmation
OWNER
EPC CONTRACTOR
NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KUWAIT OIL COMPANY (K.S.C.) A Subsidiary of Kuwait Petroleum Corporation
COMMENT RESOLUTION SHEET DOCUMENT NO. 50489-530-051-SPC-1002
CONTRACT NO.: 14050489 PROJECT NO.: EF1902
Sr. No.
Rev
VALVE MATERIAL SPECIFICATION
Company Comment
L&T Response As per Comapany standards for Gate/ Globe valves for Handwheel MOC has been defined. Valve MOC
6
Handwheel material shall be as per specific valve standard and KOC-MP-010 and KOC valve standards. Ensure data sheets are in compliance where applicable
CS Valves (0.5”-1.5”) CS Valves (2” & above) SS Valves (0.5”-1.5”) SS Valves (2” & above) Cu-Alloy (Potable Water) Cu-Alloy ( Brackish / Fire Water )
Handwheel MOC Malleable Iron/ Steel Malleable Iron / Ductile Iron / Steel
Malleable Iron / Aluminum / Steel / Cu-Alloy
We have generalised the MOC for valve handwheel in Valve Material Specifications as Malleable Iron / Ductile Iron / Cast Steel. The same is in compliance with KOC standards for valves
7
8
For bolts on valves which are direct buried, insulated or otherwise denied atmospheric exposure, bolting material ASTM A 193 Gr. B8 / ASTM A194 Gr.8 shall be used in Pipe Classes where the same has been specified for flanged connections
Company standards KOC-MP013/014/015/016 and related addenda shall be referenced in manufacturing and testing for each valve material specification sheet
For valves with MOC as SS / SDSS bolting material has been defined as ASTM A193 Gr B8M / ASTM A 194 Gr 8M. However pl. note that none of the valve in the project is direct buried. All underground valves are located in the valve pit. Para 8.0, (Technical Requirements) has been defined in the main body of the specification which incorporate these comments. Refer SECTION 4.1.2 of Doc. Valve Material Specification. This defines all relevant “KOC Standards and Engineering Group Specifications“. Also in each valve specification sheet, Note no. 1 is specifically defined as “This Valve Specification Sheet shall be read in conjunction with technical notes to Valve Material Specification”
B
DATE :
Page 2 of 6 17-Jan-15
Company Confirmation
OWNER
EPC CONTRACTOR
NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KUWAIT OIL COMPANY (K.S.C.) A Subsidiary of Kuwait Petroleum Corporation
COMMENT RESOLUTION SHEET DOCUMENT NO. 50489-530-051-SPC-1002
CONTRACT NO.: 14050489 PROJECT NO.: EF1902
Sr. No.
VALVE MATERIAL SPECIFICATION
Company Comment Inspection and testing of valves shall be fully compliant with KOC valve standards
9
10
11
Rev
KOC-MP-013/014/'015/016/033 ensure testing requirements are fully compliant in Valve material specification For valves with a back seat, include back seat testing specification shall be included in the relevant data sheet
For sour service carbon steel piping classes (CxxB),the valve trim material is to be selected from those listed as available in KOC-MP-010.Data sheet states SDSS which is not permitted for this line class. Contractor to revise to a suitable material, considering Appendix II of KOCMP-010
L&T Response
Refer L&T Response to company comments at Sr. No.8
Back Seat Testing requirements shall be governed by the relevant Testing Standards (eg. API 598, MSS-SP-80 etc.) as defined in Valve Material Specification. Selection of MOC has been done based on Appendix-II of KOC-MP-010, considering composition of service fluid. Appendix II of KOC-MP-010 permits use of Duplex / Super Duplex SS based on respective stream conditions in other lines. 25Cr. Valves (MOC: SDSS) are defined in P&ID’s for several lines having piping classes CxxB. Refer SECTION 19.0 of Piping Material Specification (Doc.No.:50489-530-051SPC-1001) This section defines “ TRIM Material Selection of Valves for Sour Service”.
Refer L&T Response to company comments at
12
Material specification for C35B shall be Carbon steel body, Contractor to remove C35B from valve #51479 which is a SDSS valve and other similar instances.
Valves with Body/ Bonnet/ Cover MOC as Stainless Steel :
13
LIST OF CHANGES Contractor to submit a technical query for the use of different bolting material for valves for review. Recommendations in items #2 and #3 are acceptable for implementation
Sr. No.11. SDSS valves shall be used wherever specified in P&ID in the same piping class.
Bolting Materials shall be revised to Stainless Steel (A193 Gr. B8M / A194 Gr. 8M) in line with company standards for valves
B
DATE :
Page 3 of 6 17-Jan-15
Company Confirmation
OWNER
EPC CONTRACTOR
NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KUWAIT OIL COMPANY (K.S.C.) A Subsidiary of Kuwait Petroleum Corporation
COMMENT RESOLUTION SHEET DOCUMENT NO. 50489-530-051-SPC-1002
CONTRACT NO.: 14050489 PROJECT NO.: EF1902
Sr. No.
Rev
VALVE MATERIAL SPECIFICATION
Company Comment
L&T Response
14
Add note to list of changes to indicate the use of stellited seats for 800# valves in piping class C13A.This is a change from the FEED document and therefore requires indication in the list of changes
Noted and complied
15
Section 4.1.3- Add reference to Pipeline data sheet. There are check valves on the pipelines, local to the disposal wells
Noted and complied. Valve Data Sheets for pipeline valves shall be submitted through separate Doc. Noted and complied.
16
Section 6.0 part 2) - Statement should read "pressure ratings........are expressed as per ASME B 16.5......"
17
Section 7.10 Revise requirement for gear operators for plug valve to be in compliance with KOC-MP016.Requirement to provide for sizes 6" and larger for Classes 150# and 300# and 4" and larger for Classes 600# and 900#
Nominal pressure ratings for Flanges, Valves are defined as per ASME B16.5, Class rating for socket weld and threaded end connections shall be series 3000# etc. as per ASME B16.11. As per KOC-MP-016, Plug Valves shall have Gear Operator as per following Criteria : Class
Sizes
150#, 300# 600#
> 6” NB > 4” NB
Same has been defined in submitted Doc. “ Valve Material Specification”
18
Clause 7.11- Remove this clause as there are valves other than globe which are used for throttling function. It is feasible to state that globe valves are to be used for throttling only
Noted and complied.
19
Clause 7.13 - change the word "shall" to "should be" as this is not a contractual requirement
Noted and complied.
20
Section 7.16 State a requirement for a minimum 150mm long seamless pipe nipple
We have specified clear requirement on pipe nipple length as 150mm. Specifying length as “Minimum 150 mm, may cause discrepancy in terms of pipe nipple length in items being supplied by different vendors”.
B
DATE :
Page 4 of 6 17-Jan-15
Company Confirmation
OWNER
EPC CONTRACTOR
NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KUWAIT OIL COMPANY (K.S.C.) A Subsidiary of Kuwait Petroleum Corporation
COMMENT RESOLUTION SHEET DOCUMENT NO. 50489-530-051-SPC-1002
CONTRACT NO.: 14050489 PROJECT NO.: EF1902
Sr. No.
Rev
VALVE MATERIAL SPECIFICATION
Company Comment
DATE :
L&T Response
21
Noted and complied.
22
Remove piping class C15B and C35B from data sheets for valves with SDSS construction, this material is not specified for the particular piping class
Refer L&T response comments at Sr. No.11
to
company
23
Revise index and data sheets for Valves in line class C35B to have trim materials selected from the prescribed options in KOC-MP-010. Refer to comment 11 for further details.
Refer L&T response comments at Sr. No.11
to
company
Refer pipe class Q35A, KOC-MP-010 : Service limit states Cu-Ni material has test P/T rating of 20 bars @ 38 °C .
24
As per Note 5: “If Pressure / Temperature ratings per EEMUA or MSS SP-80 are exceeded, full Duplex Stainless Steel material shall be used for piping, components and valves”. SDSS MOC for piping components of size range 2” & below has been selected based on this. The Design Pressure in wash water circuit are expected to be more than 20 bars.
25
For Valve data sheets with both piping classes C13B & F10A,add note to indicate Monel trim is for class F10A only
Noted and complied
26
Valve data sheet 54301 - move note 15 to Material of Construction section, rather than under Type of Construction heading.
Noted and complied
Page 5 of 6 17-Jan-15
Company Confirmation
Section 7.19 - Add abbreviation for BOQ in abbreviations table. Remove details of limit switch specification, this shall be covered in instrumentation documents. Make reference to applicable instruments specification instead of providing details.
Piping class Q35A to have Bronze/Ni-AI Bronze valves as per KOC-MP-010
B
OWNER
EPC CONTRACTOR
NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KUWAIT OIL COMPANY (K.S.C.) A Subsidiary of Kuwait Petroleum Corporation
COMMENT RESOLUTION SHEET DOCUMENT NO. 50489-530-051-SPC-1002
CONTRACT NO.: 14050489 PROJECT NO.: EF1902
Sr. No.
Rev
VALVE MATERIAL SPECIFICATION
Company Comment
27
For Piping class C15B, there is no approval to use Dual plate type check valve. Revise data sheets to show permitted check valves only as per KOC-MP-010
28
All valves shall be hydro tested and pneumatic tested as per KOC standards for valves. Contractor shall revise data sheets to comply with this requirement
DATE :
L&T Response
Sr. No.8
Page 6 of 6 17-Jan-15
Company Confirmation
Noted and complied
Refer L&T Response comments at
B
to
company
NEW GATHERING CENTRE GC-30, IN NORTH KUWAIT
DOCUMENT NO
KOC CONTRACT NO.: 14050489
50489-530-051-SPC-1002
LIST OF CHANGES WITH RESPECT TO FEED DOCUMENTS FOR PIPING VALVES Item No.
1
2
3
KOC Document No.
KOC Standard for Valves: Part 1 - Ball Valves, KOC-MP033 Part 1, KOC-MP-010
KOC Standard for Valves: Part 1 - Ball Valves, KOC-MP033 Part 1
KOC Standard for Valves
REV B
Reference / Pipe Class
ITB Requirements
L&T Recommendation
-----
KOC Standard for Ball Valves : Ball valve intended for potable water service shall be in accordance with standard AWWA C507 KOC-MP-010 : Ball Valves have been defined as per Design STD API 6D / BS EN ISO 17292.
All Ball Valves have been defined as per Design Std. API 6D / BS EN ISO 17292 in line with Doc No. KOC-MP-010.
-----
Part. 1.0, Note-2 As per this note, class 800 valves, Socket Weld / Threaded Type are of reduced bore. Doc. No. EF1902-015-LH-1002-ADD.DE2 (Add. To Piping Design) Pt. 9. clause 5.0 : " Whenever Ball Valve are provided, they shall be Full Bore Type."
All Ball Valves have been defined as full bore in line with Doc. No. EF1902-015-LH-1002ADD.DE2.
C13A
Trim Material has been defined as 13% Cr in Gate, Globe & Check Valves for both Small (800#) and Large (150#) Bore Valves in KOC-MP-010.
As per KOC Standards for valves, following valves shall have stellited surfaces. Small Bore : 800# Large Bore : 600# & above Trim Material has been defined as Stellited for Small Bore (800#) Gate, Globe & Check Valves in line with KOC Specifications for Gate / Globe Valves.
KOC Response
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 2 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
REVISION HISTORY SHEET This page is a record of all revisions of this document. All previous issues are hereby superseded and are to be destroyed. Page No.
Clause No.
Description of Revision
5
3.2
11
4.1.2
KOC Standards and their addenda / criteria relevant to Limit Switches added.
13
6.0 (2)
Clause modified as per company comment
14
7.11
Clause modified as per company comment
14
7.13
Clause modified as per company comment
14
7.19
Clause modified as per company comment
16
8.0
Para for “Technical Requirements” added
16
9.0
Statement related to material selection guideline for sour service added.
17
9.3
Para for welding requirement added
18
12.0 (d)
Table modified to include abbreviation L : Limit Switch arrangement
20
Table – 1
Valve Data Sheet Index upgraded.
---
General
Valves with MOC as SS / SDSS : Bolting material has been revised to ASTM A193 Gr B8M / ASTM A 194 Gr 8M
---
General
Pipe classes N10B / N30B added in the following Valve Data Sheet: 51399, 51499, 52399, 52499, , 53399P, 53399D, 53499P, 53499D, 54399, 54499
---
53311D, 53312D
---
55511L
Valve Data sheet added
---
53679
Check valve data sheet related to pipe class PA9A deleted.
---
51378F, 52378F, 53378DF, 54378F
Abbreviation BOQ : Bill of Quantity added.
Valve Data Sheets deleted (Swing type Check valve has been defined for 26” & above in pipe class C15B).
Note related to valve trim material added.
Revision
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 3 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
INDEX 1.0
SCOPE ..................................................................................................................... 4
2.0
APPLICATION ......................................................................................................... 4
3.0
TERMINOLOGY ....................................................................................................... 4 3.1 3.2
4.0
DEFINITIONS ................................................................................................ 4 ABBREVIATIONS .......................................................................................... 4
REFERENCE STANDARDS, CODES AND SPECIFICATIONS ............................ 7 4.1
LIST OF STANDARD AND CODES ............................................................... 7
5.0
ENVIRONMENTAL CONDITIONS ........................................................................ 13
6.0
UNITS OF MEASUREMENT ................................................................................. 13
7.0
GENERAL REQUIREMENT .................................................................................. 13
8.0
TECHNICAL REQUIREMENTS............................................................................. 16
9.0
SOUR SERVICE REQUIREMENTS ...................................................................... 16 9.1 9.2 9.3
REQUIREMENTS FOR CARBON STEEL ................................................... 16 TECHNICAL REQUIREMENTS FOR STAINLESS STEELS AND OTHER CRA’S .......................................................................................................... 17 WELDING .................................................................................................... 17
10.0
INSPECTION AND TESTING REQUIREMENTS .................................................. 17
11.0
NON DESTRUCTIVE EXAMINATION (NDE) REQUIREMENTS ......................... 18
12.0
VALVE DATA SHEET NOMENCLATURE............................................................ 18
APPENDICES: APPENDIX-I TABLE – 1
VALVE DATA SHEET INDEX
20
VALVE DATA SHEET : DETAIL DESCRIPTION
26
APPENDIX-II
APPENDIX-III TABLE – 2
BALL VALVE NIPPLE DETAIL
237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 4 of 237
KOC Contract No
14050489
1.0
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
SCOPE a) This Specification and Valve Data Sheets describes the basic design and material requirements for different type of valves, to be used for various fluids / services such as Gas / Liquid Hydrocarbons (Sweet / Sour) and NonHydrocarbon fluids / services etc. related to process and Utility piping systems of NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT. b) This specification covers the design, manufacture, inspection, testing and supply requirements of valves for installation at the facility in Kuwait and developed based on KOC specifications.
2.0
APPLICATION All material(s) listed in this specification when supplied / installed shall be brand new and of prime quality and shall conform to the requirements of this specification, Standards / Codes / Specifications referenced herein and shall also be fit for the purpose Any exceptions or deviations from this specification along with their merits and justifications shall be brought to the attention of Purchaser for their review & approval.
3.0
TERMINOLOGY
3.1
DEFINITIONS For the purpose of this Specification the following definitions shall apply.
3.2
Company
Kuwait Oil Company (KOC)
Client
Kuwait Oil Company (KOC) and / or Its appointed representative
EPC Contractor
Larsen & Toubro Limited
ABBREVIATIONS AARH
Arithmetic Average Roughness Height
AI
Instrument Air
AL
Aluminum
AL BRZ / BRNZ
Aluminum Bronze
ANSI
American National Standards Institute
AP
Plant Air
API
American Petroleum Institute
AS
Alloy Steel
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Page No : 5 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489
ASME
American Society of Mechanical Engineers
ASS
Austenitic Stainless Steel
ASTM
American Society for Testing and Materials
BAR (g)
Bar, Gauge, (Pressure Unit)
BD
Blow down & Relief
BE
Bevel End
BHN
Brinell Hardness Number
BOQ
Bill of Quantity
BRW
Branch Weld
BRZ / BRNZ
Bronze
BS
Booster Station
BS
British Standard
BW, BWE
But Weld, But Weld End
CLR
Crack Length Ratio
CRA
Corrosion Resistant Alloy
CS
Carbon Steel
CSR
Crack Surface Ratio
CTR
Crack Thickness Ratio
DC
Chemical Drain
DD
Dedicated Drain
DH
Oily/Hydrocarbon Drain
DO
Open Drain
DP
Pressurized Drain
DPT/I/E
Dye Penetrant Testing/Inspection/Examination
DSS
Duplex Stainless Steel
FBE
Fusion Bonded Epoxy
FBEL
Fusion Boned Epoxy Lined
FBEL CS
Fusion Boned Epoxy Lined Carbon Steel
FEED
Front End Engineering Design
FF
Flat Face
FG
Fuel/ Pilot Gas
FV
Full Vacuum
GC
Gathering Center
GTAW
Gas Tungsten Arc Welding
GY
Lean Glycol
HAZ
Heat Affected Zone
HIC
Hydrogen Induced Cracking
HSC
Hydrogen Stress Cracking
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 6 of 237
KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
HSE
Health, Safety & Environment
HSEMS
Health, Safety & Environment Management System
IG
Inert Gas
IN
Inhibitor / Injection Chemicals
ISO
International Organisation of Standardization
LEL CS
Liquid Epoxy Lined Carbon Steel
LPT/I/E
Liquid Penetrant Testing/Inspection/Examination
LSAW
Longitudinal Submerged Arc Welded
MAWP
Maximum Allowable Working Pressure
MAX
Maximum
MIN
Minimum
MOP
Maximum Operating Pressure
MPT/I/E
Magnetic Particle Testing/Inspection/Examination
MSS
Manufacturer’s Standardisation Society
NACE
National Association Of Corrosion Engineers
NDT/I/E
Non Destructive Testing/Inspection/Examination
Ni Al BRNZ
Nickel Aluminum Bronze
NPS
Nominal Pipe Size
OF
Fuel Oil or Diesel
OISD
Oil Industry Safety Directorate
OSHA
Occupational Safety & Health Administration
PC
Process Condensate
PG
Process Gas or Vapour
PL
Process Liquids
PMI
Positive Material Identification
PMS
Piping Material Specification
PREN
Pitting Resistance Equivalent Number
PO
Process Oil
PSI (g)
Pounds per Square Inch, Gauge, (Pressure Unit)
PWHT
Post Weld Heat Treatment
QAP
Quality Assurance Plan
QC & QA
Quality Control & Quality Assurance
RF
Raised Face
RT/I/E
Radiographic Testing/Inspection/Examination
RTJ
Ring Type Joint
RTRP
Reinforced Thermosetting Resin Pipe
SAW
Submerged Arc Welding
SCC
Stress Corrosion Cracking
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 7 of 237
KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
SCRM
Screwed Male
SCRF
Screwed Female
SDSS
Super Duplex Stainless Steel
SOHIC
Stress Oriented Hydrogen Induced Cracking
SS
Stainless Steel
SSC
Sulfide Stress Cracking
SW, SWE
Socket Weld, Socket Weld End
TEMP
Temperature
TPIA
Third Party Inspection Agency
UNS
Unique Numbering System
UT/I/E
Ultrasonic Testing/Inspection/Examination
VA
Vent to Atmosphere
VMS
Valve Material Specification
WD
Drinking Water
WE
Effluent Water
WF
Fire Water
WO
Oily/ Hydrocarbon Water
WP
Produced Water
WPS
Welding Procedure Specification
WRC
Welding Research Council
WT
Treated Effluent Water
WW
Well/ Wash Water
XG
Foam
4.0
REFERENCE STANDARDS, CODES AND SPECIFICATIONS
4.1
LIST OF STANDARD AND CODES For additional information concerning Pressure I Temp ratings, sizes, dimensions, tolerances, materials types, grades of Pipes, Fittings, Flanges, Bolts, Nuts, Valves etc. specified in this specification, the latest edition of following standards, codes and specifications may be consulted as required.
4.1.1
National / International Standards API SPEC 5L
Specification for Line Pipe
API 6D / ISO 14313
Specification for Pipeline Valves
API SPEC 6FA
Specification for Fire Test for valves
API 594
Check Valves: Flanged, Lug, Wafer and Butt Welding
API 598
Valve Inspection and Testing
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Page No : 8 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489
API 599
Metal Plug Valves-Flanged, Threaded and Welding Ends
API 600/ ISO 10434
Steel Gate Valves-Flanged and Butt-welding Ends, Bolted Bonnets Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller for the Petroleum and Natural Gas Industries Fire Test for Quarter-turn Valves and Valves Equipped with Non-metallic Seats Metal Ball Valves – Flanged, Threaded and Welding Ends
API 602/ ISO 15761 API 607 API 608 API 609
Butterfly Valves: Double Flanged, Lug and Wafer Type
ASME B1.20.1
Pipe Threads, General Purpose (Inch)
ASME B16.5
Pipe Flanges and Flanged Fittings, NPS ½ through NPS 24
ASME B16.9
Factory-Made Wrought Butt welding Fittings
ASME B16.10
Face to Face and End to End dimensions of Valves
ASME B16.11
Forged Fittings, Socket Welding and Threaded
ASME B16.20
Metallic Gaskets for Pipe Flanges Ring Joint, Spiral Wound and Jacketed
ASME B16.21
Non-metallic Flat Gaskets for Pipe Flanges
ASME B16.24
Cast Copper Alloy Pipe Flanges and Flanged Fittings Classes 150, 300, 600, 900, 1500 and 2500
ASME B16.25
Butt welding Ends
ASME B16.34
Valves Flanged, Threaded and Welding End
ASME B16.47
Large Diameter Steel Flanges NPS 26 through NPS 60
ASME B18.2.1 ASME B18.2.2
Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and Lag Screws (Inch Series) Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts (Inch Series)
ASME B 31.3
Process Piping
ASME B36.10M
Welded and Seamless Wrought Pipe
ASME B36.19M
Stainless Steel Pipe
ASME B46.1
Surface Texture, Surface Roughness, Waviness and Lay
ASME Sec VIII DIV-I
Boiler and Pressure Vessel Code
ASTM A105/ A105M
Standard Specification for Carbon Steel Forgings for Piping Application
ASTM A123
Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 9 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
ASTM A182/ A182M
Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High Temperature Service
ASTM A193/ A193M
Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High Temperature Service Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service Standard Specification for Chromium and ChromiumNickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications
ASTM A194/ A194M ASTM A216/ A216M ASTM A234/ A234M ASTM A240/ A240M
ASTM A312/ A312M
Standard Specification for Seamless, Welded and Heavily Cold Worked Austenitic Stainless Steel Pipe
ASTM A320/ A320M
Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low Temperature Service
ASTM A351/ 351M
Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
ASTM A370
Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A388/ A388M ASTM A403/ A403M ASTM A515/ A515M ASTM A516/ A516M ASTM A671/ A671M ASTM A790/ A790M ASTM A815/ 815M ASTM A995/ A995M ASTM B61 ASTM B62
Standard Practice for Ultrasonic Examination of Heavy Steel Forgings Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings Carbon Steel Plate for Intermediate and Higher Temperature Service Standard Specification for Pressure Vessel Plate, Carbon Steel, for Moderate and Lower Temperature Service Standard Specification for Electric Fusion Welded Steel Pipe for Atmospheric and Lower Temperatures Standard Specification for Seamless and Welded Ferritic/ Austenitic Stainless Steel Pipe Standard Specification for Wrought Ferritic, Ferritic/ Austenitic, and Martensitic Stainless Steel Piping Standard Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel for Pressure Containing Parts Standard Specification for Steam or Valve Bronze Castings Standard Specification for Composition Bronze or Ounce Metal Casting
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 10 of 237
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489
ASTM B148
Standard Specification for Aluminum-Bronze Sand Castings
ASTM B366
Standard Specification for Factory made wrought Nickel and Nickel Alloy Fittings
ASTM B564
Standard Specification for Nickel Alloy Forgings
BS 1868
Specification for Steel Check Valves (Flanged and Butt Welding Ends) for Petroleum, Petrochemical and Allied Industries
BS 1873
Steel Globe and Globe Stop and Check Valves (Flanged and Butt-Welding Ends) for Petroleum, Petrochemical and Allied Industries.
BS 5353
Steel Plug Valves
BS EN 593
Butterfly Valves
BS EN 558 - 2
Industrial Valves Industrial valves - Face-to Face and Centre-to Face Dimensions of Metal Valves for use in Flanged Pipe Systems. Part 2: Class Designated Valves
BS EN 1759 - 1
Flanges and their joints – Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1 : Steel Flanges, NPS ½” to 24”
BS EN 1982
Copper and Copper Alloys - Ingots and Castings
BS EN 12165
Copper & Copper Alloys Wrought & Unwrought Forging Stock
BS EN 12420
Copper & Copper alloys Forgings
BS EN 12266
Industrial valves Testing of valves Part 1: Pressure tests, test procedures and acceptance criteria Mandatory requirements-CORR 14505; May 23, 2003 Part 2: Tests, Test Procedures and Acceptance Criteria Supplementary Requirements
BS EN ISO 10434
Bolted Bonnet Steel Gate Valves for the Petroleum, Petrochemical and Allied Industries
BS EN ISO 10497
Testing of valves - Fire Type-Testing Requirements
BS EN ISO 15761
Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller, for The Petroleum and Natural Gas Industries
BS EN ISO 17292
Metal Ball Valves for Petroleum, Petrochemical and Allied Industries
BS EN ISO 1461
Hot Dip Galvanized Coatings on Fabricated Iron and Steel Articles-Specifications and Test Methods
MSS SP-25
Standard Marking System for Valves, Fittings, Flanges and Unions
MSS -SP-45
Bypass and Drain Connection
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 11 of 237
KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Rev
50489-530-051-SPC-1002
B
MSS-SP-53
Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fitting and Other Piping Components – Magnetic Particle Examinations Method
MSS-SP-55
Quality Standard for Steel Castings for Valves, Flanges and Fitting and Other Piping Components – visual method for evaluation of surface irregularities.
MSS-SP-72
Ball valve with Flanged or Butt Welding Ends for General service Specification for High-Test , Wrought, Butt-Welding Fitting
MSS SP-75 MSS SP-80
Bronze gate, globe, angle and Check Valves
MSS SP-83
Class 3000 Steel Pipe Unions Socket Welding and Threaded
MSS SP-97
Integrally Reinforced Forged Branch Outlet Fittings – Socket Welding, Threaded and Butt Welding Ends
MSS SP-110
Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends
NACE MR 0175 / ISO 15156
Petroleum and natural gas Industries - Materials for use in H2S containing environments in oil and gas production Parts 1 to 3, including: Part 1 Technical Corrigendum 1 published 01/09/2005; Part 2 Technical Corrigendum 1 published 01/09/2005; Part 3 Technical Corrigendum 1 published 15/02/2005; Part 3 Technical Corrigendum 2 published 01/09/2005. Evaluating Elastomeric Materials in Sour Gas Environment
NACE TM 0187 NACE TM 0284 NACE TM 0177 PFI ES-24 4.1.2
Contractor Document Number
Evaluation of Pipeline and Pressure Vessel Steels for Resistance to Hydrogen Induced Cracking Laboratory Testing of Metals for Resistance to Sulfide Stress Cracking and Stress Corrosion Cracking in H2S Environments Pipe Bending Methods, Tolerances, Process and Material Requirements"
KOC Standards and Engineering Group Specifications Piping design and materials covered by this specification shall comply with all the applicable sections of KOC Standards and Specifications their addendum and criteria of which the following are specifically referenced in this specification EF1902-KOC-I-010-CRT-DGO
Criteria to KOC-I-010 : Control and Shut Down Valves
EF1902-KOC-MP-010-CRT-DE2
Criteria to KOC-MP-010 : Piping Material Classes
EF1902-015-JH-1903-ADD-DGO
Addendum to 015-JH-1903 : General Instrument
EF1902-015-LH-1002-ADD-DE2
Addendum to 015-LH-1002 : Piping Design
EF1902-KOC-MP-013-CRT-DE2
Criteria to KOC-MP-013 : KOC Standard for Gate Valves
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 12 of 237
KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
EF1902-KOC-MP-014-CRT-DE2 EF1902-KOC-MP-015-CRT-DE2 EF1902-KOC-MP-016-CRT-DE2 EF1902-KOC-MP-033-CRT-DE2 KOC-G-004
Rev
50489-530-051-SPC-1002
B
Criteria to KOC-MP-014 : KOC Standard for Globe Valves Criteria to KOC-MP-015 : KOC Standard for Check Valves Criteria to KOC-MP-016 : KOC Standard for Plug Valves Criteria to KOC-MP-033 : KOC Standard for Ball Valves KOC Standard for Packing, Marking and Documentation
KOC-G-007
KOC Standard for Basic Design Data.
KOC-I-0101
KOC Standard for Control and Shut Down Valves
KOC-MP-010
KOC Standard for Piping Material Classes
KOC-MP-013
KOC Standard for Gate Valves
KOC-MP-014
KOC Standard for Globe Valves
KOC-MP-015
KOC Standard for Check Valves
KOC-MP-016 / KOC-MP-033, Part-5 KOC-MP-031,Part 1 KOC-MP-031,Part 2
Design and Materials KOC Standard for Plug Valves KOC Standard for Gaskets for Pipe Flanges: Types, Design and Materials KOC Recommended Practice for Gaskets for Pipe Flanges: Selection Criteria, Handling and Installation
KOC-MP-033,Part 1
KOC Standard for Ball Valves
KOC-P-001
015-JH-1903
KOC Standard for Painting and Coating of External Metal Surfaces KOC Standard For Colour Coding of Pipework for Identification of Fluids & Services KOC Standard for QA / QC Requirements for Projects KOC Standard for Positive Material Identification (PMI) General Instrument
015-LH-1002
Piping Design
015-WH-1003
Inspection of Casting for General Pressure Service
KOC-P-017 KOC-Q-014 KOC-Q-015
4.1.3
Contractor Document Number
Project Specific Documents 50489-530-051-SPC-1001
Piping Material Specification
50489-530-020-DIA-1002
Material Selection Diagram
50489-530-020-LST-1002
Line List
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
5.0
Page No : 13 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
ENVIRONMENTAL CONDITIONS Environmental requirements to be considered with respect to piping design shall be established from KOC Standard KOC-G-007, entitled “KOC Standard for Basic Design Data”.
6.0
UNITS OF MEASUREMENT The metric units of measure shall be used throughout with the following exceptions: 1) Nominal pipe size (NPS) expressed in inches. 2) Nominal pressure ratings for Flanges, Valves are defined as per ASME B16.5, Class rating for socket weld and threaded end connections shall be series 3000# etc. as per ASME B16.11.
7.0
GENERAL REQUIREMENT
7.1
Valve shall be designed, manufactured, tested, inspected and marked as per the manufacturing standards; design codes and project specifications (latest editions) indicated in the respective valve data sheets. In case of a conflict between the KOC Standards (Refer Clause 4.1.2) & valve data sheets, valve data sheets shall govern over respective standards. Approval of drawings shall be valid only for design / constructional features.
7.2
Vendor shall quote in strict accordance with the valve specification sheets, technical notes and all other referred documents. Deviations to the specification sheets, technical notes etc., if any, shall be asked specifically.
7.3
All codes and standards for manufacturing, testing, inspection etc. shall be of latest edition of such documents.
7.4
All flanged valves shall have flanges integral (except forged valves) with the valve body. Flange face finish shall be normally specified in the valve specification sheet as smooth finish, 125 AARH etc. The interpretation for range of face finish shall be as follows: Serrated Finish / Smooth Finish/125AARH : 125 to 250 µin AARH (For RF Flanges) Extra smooth finish/63 AARH
7.5
: 32-63 µin AARH (For RTJ Flanges)
Valve body / bonnet shall be forged / cast as specified. Forgings are acceptable in place of castings but not vice-versa.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
14050489
7.6
VALVE MATERIAL SPECIFICATION
Page No : 14 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
If an overlay weld-deposit is used for the body seat ring, seating surface, the corrosion resistance of the seat ring base material shall be at least equal to the corrosion resistance of the material of the shell / Body
7.7
Threaded Seat rings shall be screwed in place to prevent loosening. This may be done by Tack welding.
7.8
Manual gear operators shall be provided for frequently operated gate and globe valves in the ratings and sizes listed below:
7.9
7.10
Rating
Size
Class 150
12 in and larger
Class 300
10 in and larger
Class 600
6 in and larger
Class 900
4 in and larger
Gear operators shall be provided for Ball Valves in the sizes listed below: Rating
Size
Class 150
6 in and larger
Class 300
6 in and larger
Class 600
6 in and larger
Class 900
4 in and larger
Gear operators shall be provided for Plug Valves in the sizes listed below: Rating
Size
Class 150
8 in and larger
Class 300
8 in and larger
Class 600
6 in and larger
Class 900
6 in and larger
7.11
Globe Valves are to be used for throttling only.
7.12
All Butterfly Valves 8 in. and larger shall be provided with a gear operator.
7.13
Following requirement for check valves should be met over and above the valve spec sheet requirements: Wherever check valve disc assembly is supported from the cover of the check valves, the following shall be ascertained:
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 15 of 237
KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
−
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Positive location / positioning of cover must be provided to ensure correct alignment of the valve disc.
−
Hinge pin design must permit accurate alignment of the disc and valve seat.
7.14
Wherever Ball valve is provided, they shall be full bore type
7.15
Ball Valves shall be provided with Lock open / Lock closed provision
7.16
Soft-seated SW end ball valves shall have a 150 mm long seamless pipe nipple welded to each end of the valve. Nipples are to be welded prior to valve assembly. Nipple specifications shall be as per Appendix III.
7.17
Each Ball and Plug valve shall be supplied with a lever / wrench except for gear operated / motor operated valves
7.18
The ball of ball valve shall not protrude outside the end flanges of valve.
7.19
Limit Switch requirements on applicable Plug valves shall be specified in BOQ. Specification of Limit switch for manually operated ON / OFF Valves shall be as per KOC-I-0101 (Rev 1) and its criteria (EF1902-KOC-I-0101-CRT-DGO)
7.20
Stem shall be forged or machined from forged / rolled bar. No casting is permitted. However, integral stem of cast stainless steel ball valve is acceptable. Stems shall be free of scratches, dents or other types of damage.
7.21
Body, Bonnet and Cover Bolts on valves shall be tightened with torque wrenches so that installed stress shall not be greater than 276 N / square mm.
7.22
All hardfacing / stellite facing shall be with Stellite No.6 or equal, having a minimum deposit thickness after final machining of 1.5 mm, unless otherwise approved by KOC. Iron content in the hardfacing due to base metal dilution shall not exceed 12%.
7.23
Gasket and Valve Stem Packing a) Spiral wound bonnet gaskets are to be provided with inner / outer ring except when encapsulated gasket type body-bonnet joints are employed. Outer ring may be avoided in case of non-circular spiral wound gasket used in 150# valve provided the outermost layer of spiral touches the bolts ascertaining the centering. Gasket surfaces (Bonnet and End connections) shall have no scratches, pin holes, dents or other type of damage. b) Valve stem packing shall be of non-asbestos material that is fire safe and shall contain inhibitors to prevent valve stem pitting. Valve stem packing shall comply to the following, as applicable:
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
•
Page No : 16 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Bronze Valves. Packing shall be in accordance with the Manufacturer’s standards.
•
Carbon Steel and Stainless Steel Valves. Valve packing shall be of non-asbestos material and fire safe. Packing shall be a five ring packing system consisting of three graphoil pre compressed and die-formed packing rings with graphite fiber top and bottom stem wiper rings. The packing shall contain a corrosion inhibitor to prevent valve stem pitting.
c) Asbestos in any form shall not be used 7.24
All other technical requirements which are not covered under this specification shall be as per applicable KOC valve standards referred in clause 4.1.2 of this specification.
8.0
TECHNICAL REQUIREMENTS
8.1
Manufacturing, Inspection and Testing of valves covered under this Valve Material Specifications shall be in full compliance with KOC Standards for valves and related addenda. All valves shall be Hydro / Pneumatic tested as per KOC standards for valves.
8.2
To have interchangeability of usage under different service conditions, all valves shall be procured with only Primer Coating applied. Primer coating shall be Inorganic Zinc Silicate. Finish paint of these valves shall be carried out after installation.
9.0
SOUR SERVICE REQUIREMENTS Material selection Guidelines per NACE MR 0175 / ISO 15156 as specified in Appendix II of KOC-MP-010 have been followed in this specification.
9.1
REQUIREMENTS FOR CARBON STEEL Materials intended to be used in sour service shall comply with the requirements of NACE MR 0175/ ISO 15156, and as supplemented in the following clauses: a) No cold forming/ bending shall be allowed b) Valve body, bonnet, disc, ball, stem etc. (all welded parts) shall have a maximum hardness of 235 BHN unless other values are specified in the applicable standards. c) All forgings shall be normalized.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489
9.2
Page No : 17 of 237
TECHNICAL REQUIREMENTS FOR STAINLESS STEELS AND OTHER CRA’S a) Stainless Steels and other CRA’s shall comply with NACE MR 0175/ ISO 15156 and Shall be suitable for the design conditions in respect of temperature, H2S partial pressure, chloride content and other applicable environmental parameters. b) Stainless steels shall be in solution annealed condition and shall meet the requirements of NACE MR0175/ ISO15156. c) The use of cold worked stainless steels is subject to the limitations imposed by NACE MR0175/ ISO15156.
9.3
WELDING Wherever weld overlay with CRA material is specified for valve components, the following conditions shall apply: (i)
The procedure/ methodology adopted shall be weld-overlay specific.
(ii)
In case of manual / automatic weld overlay process, the minimum weld overlay thickness required after machining shall be 3 mm.
(iii)
The required CRA deposit shall be obtained through a minimum of three passes.
(iv)
The machined surface of the valve component shall undergo PMI test to verify the major alloying elements.
(v)
Where barrier layer is applied prior to the overlay, the PMI results shall meet the specification of the filler rod, (for example SS316L).
(vi)
For other alloys where no barrier layer is applied, PMI results shall meet the specification of CRA material.
(vii)
The finished surface of the components shall undergo LPT and shall be free of any surface opening defects.
(viii) The weld overlay, wherever recommended, shall be done by either SS316L or 6 Mo or Inconel 625 materials. However Duplex SS and / or Super Duplex SS shall not be used for weld overlay.
10.0 INSPECTION AND TESTING REQUIREMENTS Apart from the Inspection and Testing requirements mentioned in respective KOC Standards for Valves, the following requirements shall be adhered to: a) All items and their parts shall be subjected to all mandatory as well as supplementary (wherever specified) inspections, tests and checks called-for in the respective codes/ standards & specifications/ data sheets. b) All inspection work shall be carried out in line with KOC Standard for Project QA/QC requirement, Doc. No.KOC-Q-014.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 18 of 237
KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
c) PMI-testing at vendor’s works shall be carried-out/ executed as per KOC standard for Positive Material Identification, Doc. No. KOC-Q-015. d) Further receipt of valve from vendor, all new manual / actuated (on / off) valves shall be subject to pressure testing in company approved workshop’s in Kuwait and witnessed by company. All testing shall be performed & witnessed by Company’s or Contractor’s representatives / nominated TPIA. In the event of failure of any new Valve during pressure testing, company reserve the right to reject the materials at no cost to company. The Company reserves the right to accept these valves as repaired or for them to be replaced at no extra cost to the Company.
11.0 NON DESTRUCTIVE EXAMINATION (NDE) REQUIREMENTS Non-Destructive examination of all valves shall be as per Para 9.8 of KOC Standard for Ball Valves- Part 1, Doc. No. KOC-MP-033 Part 1.
12.0 VALVE DATA SHEET NOMENCLATURE Each Valve data sheet number consists of at least five (5) digits. Suffix shall be added to the same depending upon the optional requirement. a) The first two digit of the data sheet number defines the type of Valve: 51
Gate Valve
52
Globe Valve
53
Check Valve
54
Ball Valve
55
Plug Valve
56
Butterfly Valve
57
Needle Valve
b) The third digit of the data sheet number defines the valve rating 0 3 4
800# 150# 300#
5 6 7
600# 900# 1500#
c) The last two digits of the data sheet number define the MOC/ valve metallurgy: 01
CS
11
Body : CS + Trim : Super Duplex, NACE
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
Page No : 19 of 237
KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
12
Body : CS + Trim : SS316L, NACE
61
SS316 / 316L
63
Body : SS316 / 316L + Trim : Super Duplex, NACE
64
Body : SS316 / 316L + Trim : SS316L, NACE
78
NI-AL-Bronze
79
Super Duplex SS, NACE
80
Bronze
81
CS ( EPDM Lined) + Trim : Monel / Ni-Al-Bronze
82
Super Duplex SS
90
CS ( EPDM Lined) + Trim : Super Duplex SS, NACE
98
CS (Inconel Lined) + Trim : Inconel, NACE
99
Inconel 625, NACE
d) The suffix to the five digit data sheet number defines specific / special requirements (optional): B
Butt weld
D
Dual Plate Check Valve
F
Flat Face
L
Limit Switch arrangement
P
Piston Type (Flanged Only)
S
SCRF
X
SW x SCRF
Y
Ball Valve spring loaded)
Z
Swing Type (SW Only)
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 20 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
APPENDIX - I TABLE - 1 : VALVE DATA SHEET INDEX
SR. NO.
SHEET NO.
1
51001
2
51001X
MATERIAL OF CONSTRUCTION
PIPING CLASS
VALVE TYPE
SIZE RANGE (INCH)
RATING
C13A
Gate
0.5 - 1.5
C13A
Gate
S10A, S30A, S60A S10A, S30A, S60A
END Remarks CONNECTION
BODY
TRIM
800#
Carbon Steel
Stellited
SW
0.5 - 1.5
800#
Carbon Steel
Stellited
SW X SCRF
Gate
0.5 - 1.5
800#
SS316 / 316L
SS316 / 316L
SW
Gate
0.5 - 1.5
800#
SS316 / 316L
SS316 / 316L
SW X SCRF
3
51061
4
51061X
5
51082
Q35A, F30A
Gate
0.5 - 1.5
800#
Super Duplex SS
Super Duplex SS
SW
6
51082X
Q35A, F30A
Gate
0.5 - 1.5
800#
Super Duplex SS
Super Duplex SS
SW X SCRF
7
51301
C13A
Gate
2 - 16
150#
Carbon Steel
13 % Chrome
RF
8
51311
C15B
Gate
0.5 - 48
150#
Carbon Steel
Super Duplex SS
RF
NACE
9
51312
C15B
Gate
0.5 - 48
150#
Carbon Steel
SS316L
RF
NACE
10
51361
S10A
Gate
2 - 12
150#
SS316
SS316 / 316L
RF
0.5 - 1.5
150#
SS316 / 316L
Super Duplex SS
RF
11
51363
S10B
Gate 2 - 12
150#
SS316
Super Duplex SS
RF
0.5 - 1.5
150#
SS316 / 316L
SS316L
RF
2 - 12
150#
SS316
SS316L
RF
12
51364
S10B
NACE
Gate
NACE
13
51378
Q15A
Gate
3 - 24
150#
NI-AL Bronze
Monel / NI-AL Bronze
RF
14
51378F
C13B, F10A
Gate
2 - 24
150#
NI-AL Bronze
Monel / NI-AL Bronze
FF
15
51379
Q15B, F10B, C15B
Gate
0.5 - 36
150#
Super Duplex SS
Super Duplex SS
RF
NACE
16
51379F
F10B
Gate
2 - 36
150#
Super Duplex SS
Super Duplex SS
FF
NACE
17
51380F
F10A, Q15A
Gate
0.5 - 2
150#
Bronze
Bronze
FF
18
51380S
C13B
Gate
0.5 - 3
150#
Bronze
Bronze
SCRF
19
51398
N10C
8 - 16
150#
CS Inconel Lined
Inconel
RF
NACE
Gate
0.5 - 20
150#
Inconel
Inconel
RF
NACE NACE
B
20
51399
N10B, N10C
21
51411
C35B
Gate
0.5 - 16
300#
Carbon Steel
Super Duplex SS
RF
22
51461
S30A
Gate
2 - 12
300#
SS316
SS316 / 316L
RF
0.5 - 1.5
300#
SS316 / 316L
Super Duplex SS
RF
23
51463
S30B
Gate 2 - 16
300#
SS316
Super Duplex SS
RF
NACE
24
51478
Q35A
Gate
3 - 32
300#
NI-AL Bronze
Monel / NI-AL Bronze
RF
25
51478F
F30A
Gate
2 - 24
300#
NI-AL Bronze
Monel / NI-AL Bronze
FF
26
51479
C35B, F30B, S30B, Q35B
Gate
0.5 - 24
300#
Super Duplex SS
Super Duplex SS
RF
NACE
27
51479F
F30B
Gate
2 - 24
300#
Super Duplex SS
Super Duplex SS
FF
NACE
28
51482
Q35A
Gate
2
300#
Super Duplex SS
Super Duplex SS
RF
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Page No : 21 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
MATERIAL OF CONSTRUCTION
SR. NO.
SHEET NO.
PIPING CLASS
VALVE TYPE
SIZE RANGE (INCH)
RATING BODY
TRIM
29
51498
N30C
Gate
8 - 16
150#
CS Inconel Lined
Inconel
RF
NACE
30
51499
N30B, N30C
Gate
0.5 - 16
300#
Inconel
Inconel
RF
NACE
31
51511
C65B
Gate
0.5 - 24
600#
Carbon Steel
Super Duplex SS
RF
NACE
32
51561
S60A
Gate
2 - 12
600#
SS316
SS316 / 316L
RF
33
51579
C65B
Gate
0.5 - 24
600#
Super Duplex SS
Super Duplex SS
RF
NACE
34
51779
Q95B
Gate
0.5 - 2
1500#
Super Duplex SS
Super Duplex SS
RF
NACE
35
52001
C13A
Globe
0.5 - 1.5
800#
Carbon Steel
Stellited
SW
36
52061
S10A, S30A, S60A
Globe
0.5 - 1.5
800#
SS316 / 316L
SS316 / 316L
SW
37
52082
F30A, Q35A
Globe
0.5 - 1.5
800#
Super Duplex SS
Super Duplex SS
SW
38
52301
C13A
Globe
2 - 16
150#
Carbon Steel
13 % Chrome
RF
39
52311
C15B
Globe
0.5 - 16
150#
Carbon Steel
Super Duplex SS
RF
NACE
40
52312
C15B
Globe
0.5 - 16
150#
Carbon Steel
SS316L
RF
NACE
41
52361
S10A
Globe
2 - 12
150#
SS316
SS316 / 316L
RF
0.5 - 1.5
150#
SS316 / 316L
Super Duplex SS
RF
42
52363
S10B
Globe 2 - 12
150#
SS316
Super Duplex SS
RF
0.5 - 1.5
150#
SS316 / 316L
SS316L
RF
2 - 12
150#
SS316
SS316L
RF
43
52364
B
S10B
END Remarks CONNECTION
NACE
Globe
NACE
44
52378
Q15A
Globe
3 - 16
150#
NI-AL Bronze
Monel / NI-AL Bronze
RF
45
52378F
C13B, F10A
Globe
2 - 16
150#
NI-AL Bronze
Monel / NI-AL Bronze
FF
46
52379
Q15B, F10B, C15B
Globe
0.5 - 16
150#
Super Duplex SS
Super Duplex SS
RF
NACE
47
52379F
F10B
Globe
2 - 16
150#
Super Duplex SS
Super Duplex SS
FF
NACE
48
52380F
F10A, Q15A
Globe
0.5 - 2
150#
Bronze
Bronze
FF
49
52380S
C13B
Globe
0.5 - 3
150#
Bronze
Bronze
SCRF
50
52399
N10B, N10C
Globe
0.5 - 16
150#
Inconel
Inconel
RF
NACE
51
52411
C35B
Globe
0.5 - 12
300#
Carbon Steel
Super Duplex SS
RF
NACE
52
52461
S30A
Globe
2 - 12
300#
SS316
SS316 / 316L
RF
0.5 - 1.5
300#
SS316 / 316L
Super Duplex SS
RF
53
52463
S30B
Globe 2 - 12
300#
SS316
Super Duplex SS
RF
B
NACE
54
52478
Q35A
Globe
3 - 12
300#
NI-AL Bronze
Monel / NI-AL Bronze
RF
55
52478F
F30A
Globe
2 - 12
300#
NI-AL Bronze
Monel / NI-AL Bronze
FF
56
52479
Q35B, F30B, C35B
Globe
0.5 - 12
300#
Super Duplex SS
Super Duplex SS
RF
NACE
57
52479F
F30B
Globe
2 - 16
300#
Super Duplex SS
Super Duplex SS
FF
NACE
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 22 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
MATERIAL OF CONSTRUCTION
SR. NO.
SHEET NO.
PIPING CLASS
VALVE TYPE
SIZE RANGE (INCH)
RATING BODY
TRIM
58
52482
Q35A
Globe
2
300#
Super Duplex SS
Super Duplex SS
RF
59
52499
N30B, N30C
Globe
0.5 - 12
300#
Inconel
Inconel
RF
NACE
60
52511
C65B
Globe
0.5 - 12
600#
Carbon Steel
Super Duplex SS
RF
NACE
61
52561
S60A
Globe
2 - 12
600#
SS316
SS316 / 316L
RF
62
52579
C65B
Globe
2-6
600#
Super Duplex SS
Super Duplex SS
RF
63
53001
C13A
Check
0.5 - 1.5
800#
Carbon Steel
Stellited
SW
64
53061
S10A, S30A, S60A
Check
0.5 - 1.5
800#
SS316 / 316L
SS316 / 316L
SW
65
53061Z
S30A, S60A
Check
0.5 - 1.5
800#
SS316 / 316L
SS316 / 316L
SW
66
53082
F30A, Q35A
Check
0.5 - 1.5
800#
Super Duplex SS
Super Duplex SS
SW
67
53301
C13A
Check
2 - 16
150#
Carbon Steel
13 % Chrome
RF
68
53311P
C15B
Check
0.5 - 1.5
150#
Carbon Steel
Super Duplex SS
RF
NACE
69
53311
C15B
Check
2 - 48
150#
Carbon Steel
Super Duplex SS
RF
NACE
70
53312P
C15B
Check
0.5 - 1.5
150#
Carbon Steel
SS316L
RF
NACE
71
53312
C15B
Check
2 - 48
150#
Carbon Steel
SS316L
RF
NACE
72
53361
S10A
Check
2 - 12
150#
SS316
SS316 / 316L
RF
73
53363P
S10B
Check
0.5 - 1.5
150#
SS316 / 316L
SS316 / 316L
RF
NACE
74
53363
S10B
Check
2 - 12
150#
SS316
SS316 / 316L
RF
NACE
75
53364P
S30B
Check
0.5 - 1.5
150#
SS316 / 316L
SS316 / 316L
RF
NACE
76
53364
S30B
Check
2 - 12
150#
SS316
SS316 / 316L
RF
NACE
77
53378D
Q15A
Check
3 - 24
150#
NI-AL Bronze
Monel / NI-AL Bronze
RF
78
53378DF
C13B, F10A
Check
2 - 24
150#
NI-AL Bronze
Monel / NI-AL Bronze
FF
79
53379P
F10B, Q15B
Check
0.5 - 1.5
150#
Super Duplex SS
Super Duplex SS
RF
NACE
80
53379D
Q15B
Check
2 - 36
150#
Super Duplex SS
Super Duplex SS
RF
NACE
81
53379DF
F10B
Check
2 - 36
150#
Super Duplex SS
Super Duplex SS
FF
NACE
82
53380P
F10A, Q15A
Check
0.5 - 2
150#
Bronze
Bronze
FF
83
53380S
C13B
Check
0.5 - 3
150#
Bronze
Bronze
SCRF
84
53399P
N10B, N10C
Check
0.5 - 2
150#
Inconel
Inconel
RF
NACE
85
53399D
N10B, N10C
Check
3 - 20
150#
Inconel
Inconel
RF
NACE
B
B
END Remarks CONNECTION
NACE
B
86
53411P
C35B
Check
0.5 - 1.5
300#
Carbon Steel
Super Duplex SS
RF
NACE
87
53411
C35B
Check
2 - 16
300#
Carbon Steel
Super Duplex SS
RF
NACE
88
53461
S30A
Check
2 - 12
300#
SS316
SS316 / 316L
RF
89
53478
Q35A
Check
3 - 24
300#
NI-AL Bronze
Monel / NI-AL Bronze
RF
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 23 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
MATERIAL OF CONSTRUCTION
SR. NO.
SHEET NO.
PIPING CLASS
VALVE TYPE
SIZE RANGE (INCH)
RATING
END Remarks CONNECTION
BODY
TRIM
90
53478D
Q35A
Check
3 - 32
300#
NI-AL Bronze
Monel / NI-AL Bronze
RF
91
53479P
F30B, Q35B
Check
0.5 - 1.5
300#
Super Duplex SS
Super Duplex SS
RF
NACE
92
53479D
Q35B
Check
2 - 24
300#
Super Duplex SS
Super Duplex SS
RF
NACE
93
53482D
Q35A
Check
2
300#
Super Duplex SS
Super Duplex SS
RF
94
53498D
N30C
Check
8 - 16
300#
CS Inconel Lined
Inconel
RF
NACE
95
53499P
N30B, N30C
Check
0.5 - 2
300#
Inconel
Inconel
RF
NACE
Check
3 - 16
300#
Inconel
Inconel
RF
NACE
B
96
53499D
N30B, N30C
97
53511P
C65B
Check
0.5 - 1.5
600#
Carbon Steel
Super Duplex SS
RF
NACE
98
53511
C65B
Check
2 - 24
600#
Carbon Steel
Super Duplex SS
RF
NACE
99
53511D
C65B
Check
2 - 24
600#
Carbon Steel
Super Duplex SS
RF
NACE
100
53561
S60A
Check
2 - 12
600#
SS316
SS316 / 316L
RF
101
53679D
Q95B
Check
3 - 20
900#
Super Duplex SS
Super Duplex SS
RTJ
NACE
102
53779P
Q95B
Check
0.5 - 1.5
1500#
Super Duplex SS
Super Duplex SS
RTJ
NACE
103
53779D
Q95B
Check
2
1500#
Super Duplex SS
Super Duplex SS
RTJ
NACE
104
54001
C13A
Ball
0.5 - 1.5
800#
Carbon Steel
SS316L
SW
105
54001S
C13A
Ball
0.5
800#
Carbon Steel
SS316L
SCRM X SCRF
106
54001X
C13A
Ball
0.75 - 1.5
800#
Carbon Steel
SS316L
SW X SCRF
107
54061
Ball
0.5 - 1.5
800#
SS316 / 316L
SS316 / 316L
SW
108
54061S
Ball
0.5
800#
SS316 / 316L
SS316 / 316L
SCRM X SCRF
109
54061X
Ball
0.75 - 1.5
800#
SS316 / 316L
SS316 / 316L
SW X SCRF
110
54082
F30A, Q35A
Ball
0.5 - 1.5
800#
Super Duplex SS
Super Duplex SS
SW
111
54082Y
F30A
Ball
0.5 - 1.5
800#
Super Duplex SS
Super Duplex SS
SW
112
54082S
F30A, Q35A
Ball
0.5
800#
Super Duplex SS
Super Duplex SS
SCRM X SCRF
113
54082X
F30A, Q35A
Ball
0.75 - 1.5
800#
Super Duplex SS
Super Duplex SS
SW X SCRF
114
54301
C13A
Ball
2 - 16
150#
Carbon Steel
SS316L
RF
115
54311
C15B
Ball
0.5 - 36
150#
Carbon Steel
Super Duplex SS
RF
NACE
116
54312
C15B
Ball
0.5 - 36
150#
Carbon Steel
SS316L
RF
NACE
117
54361
S10A
Ball
2 - 12
150#
SS316
SS316 / 316L
RF
0.5 - 1.5
150#
SS316 / 316L
Super Duplex SS
RF
118
54363
S10B
Ball 2 - 16
150#
SS316
Super Duplex SS
RF
0.5 - 1.5
150#
SS316 / 316L
SS316 / 316L
RF
2 - 12
150#
SS316
SS316 / 316L
RF
3 - 24
150#
NI-AL Bronze
Monel / NI-AL Bronze
RF
119
120
54364
54378
S10A, S30A, S60A S10A, S30A, S60A S10A, S30A, S60A
S10B
Q15A
NACE
Ball
Ball
NACE
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
MATERIAL OF CONSTRUCTION
SHEET NO.
PIPING CLASS
VALVE TYPE
SIZE RANGE (INCH)
RATING
121
54378F
C13B, F10A
Ball
2 - 24
122
54379
Q15B, F10B, C15B
Ball
123
54379F
F10B
124
54380F
125
SR. NO.
Page No : 24 of 237
END Remarks CONNECTION
BODY
TRIM
150#
NI-AL Bronze
Monel / NI-AL Bronze
FF
0.5 - 36
150#
Super Duplex SS
Super Duplex SS
RF
NACE
Ball
2 - 36
150#
Super Duplex SS
Super Duplex SS
FF
NACE
F10A, Q15A
Ball
0.5 - 2
150#
Bronze
Bronze / Monel
FF
54380YF
F10A
Ball
0.5 - 2
150#
Bronze
Bronze / Monel
FF
126
54380S
C13B
Ball
0.5 - 1.5
150#
Bronze
Bronze / NI-AL-Bronze
SCRF
127
54398
N10C
Ball
8 - 16
150#
CS Inconel Lined
Inconel
RF
NACE
128
54399
N10B, N10C
Ball
0.5 - 20
150#
Inconel
Inconel
RF
NACE
129
54411
C35B
Ball
0.5 - 14
300#
Carbon Steel
Super Duplex SS
RF
NACE
130
54461
S30A
Ball
2 - 12
300#
SS316
SS316 / 316L
RF
0.5 - 1.5
300#
SS316 / 316L
Super Duplex SS
RF
131
54463
S30B
Ball 2 - 12
300#
SS316
Super Duplex SS
RF
B
NACE
132
54478
Q35A
Ball
3 - 32
300#
NI-AL Bronze
Monel / NI-AL Bronze
RF
133
54478F
F30A
Ball
2 - 24
300#
NI-AL Bronze
Monel / NI-AL Bronze
FF
134
54479
C35B, F30B, Q35B
Ball
0.5 - 24
300#
Super Duplex SS
Super Duplex SS
RF
NACE
135
54479F
F30B
Ball
2 - 24
300#
Super Duplex SS
Super Duplex SS
FF
NACE
136
54498
N30C
Ball
8 - 16
300#
CS Inconel Lined
Inconel
RF
NACE
Ball
0.5 - 16
300#
Inconel
Inconel
RF
NACE NACE
B
137
54499
N30B, N30C
138
54511
C65B
Ball
0.5 - 24
600#
Carbon Steel
Super Duplex SS
RF
139
54561
S60A
Ball
2 - 12
600#
SS316
SS316 / 316L
RF
140
54579
C65B
Ball
0.5 - 6
600#
Super Duplex SS
Super Duplex SS
RF
NACE
141
54679
Q95B
Ball
3 - 24
900#
Super Duplex SS
Super Duplex SS
RTJ
NACE
142
54779
Q95B
Ball
0.5 - 2
1500#
Super Duplex SS
Super Duplex SS
RTJ
NACE
143
55411
C35B
Plug
0.5 - 12
300#
Carbon Steel
CS with Anti Friction Inpregnated
RF
NACE
144
55511
C65B
Plug
0.5 - 24
600#
Carbon Steel
CS with Anti Friction Inpregnated
RF
NACE
55511L
C65B
Plug
0.5 - 24
600#
Carbon Steel
CS with Anti Friction Inpregnated
RF
NACE
146
56311
C15B
Butterfly
3 - 24
150#
Carbon Steel
Super Duplex SS
RF
NACE
147
56312
C15B
Butterfly
3 - 24
150#
Carbon Steel
SS316L
RF
NACE
148
56381
Q15A
Butterfly
3 - 24
150#
CS EPDM Lined
Monel / NI-AL Bronze
RF
149
56478
Q35A
Butterfly
3 - 24
300#
NI-AL Bronze
Monel / NI-AL Bronze
RF
150
57082
Q35A
Needle
0.5
800#
Super Duplex SS
Super Duplex SS
SW
151
57311
C15B
Needle
0.5 - 1.5
150#
Carbon Steel
Super Duplex SS
RF
145
B
NACE
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 25 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
MATERIAL OF CONSTRUCTION
SR. NO.
SHEET NO.
PIPING CLASS
VALVE TYPE
SIZE RANGE (INCH)
RATING
END Remarks CONNECTION
BODY
TRIM
152
57312
C15B
Needle
0.5 - 1.5
150#
Carbon Steel
SS316L
RF
NACE
153
57379
Q15B
Needle
0.5 - 1.5
150#
Super Duplex SS
Super Duplex SS
RF
NACE
154
57411
C35B
Needle
0.5 - 1.5
300#
Carbon Steel
Super Duplex SS
RF
NACE
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
14050489
VALVE MATERIAL SPECIFICATION
Page No : 26 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
APPENDIX-II VALVE DATA SHEET: DETAIL DESCRIPTION All Valve data sheet shown in TABLE-2: Valve Data Sheet Index, are described in detail in the following pages.
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51001
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
C13A
Size Range Rating Ends
Fuel Oil (Diesel), Inert Gas
SW, 3000# to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
2975 2175
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4) Bolted
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Manufacturer's Alternate/ Acceptance
Body Seat Ring Renewable / Integral 13% Cr. Steel + Stellite Facing Gate ( Wedge) Solid (Note 3) ASTM A 105 + Stellite Facing Body Forged ASTM A 105 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.
Page 27 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51001X
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
C13A
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
Size Range Rating Ends
Fuel Oil (Diesel), Inert Gas
SW X SCRD NPT(F), 3000# to ASME B16.11 Face to Face dimension Manufacturer's Standard
ASME B 16.34 2975 2175
Contractor Document Number
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4) Bolted
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 193 Gr 2H ASTM A 105
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Manufacturer's Alternate/ Acceptance
Body Seat Ring Renewable / Integral 13% Cr. Steel + Stellite Facing Gate ( Wedge) Solid (Note 3) ASTM A 105 + Stellite Facing Body Forged ASTM A 105 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.
Page 28 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51061
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S10A, S30A, S60A
Size Range Rating Ends
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor
SW, 3000 # to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard
2900 2125
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C
Bonnet Gasket
Spiral Wound
SS 316/ 316L Dual Stamped Graphite with Inconel Wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 F 316/ 316L Dual Stamped
Manufacturer's Alternate/ Acceptance
B
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Body Seat Ring Renewable / Integral ASTM A 182 F 316/ 316L Dual Stamped Gate ( Wedge) Solid (Note 3) ASTM A 182 F 316/ 316L Dual Stamped Body Forged ASTM A 182 F 316/ 316L Dual Stamped GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 29 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51061X
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S10A, S30A, S60A
Size Range Rating Ends
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor
B
SW X SCRD NPT(F), 3000# to ASME B16.11
Face to Face dimension Manufacturer's Standard
ASME B 16.34 2900 2125
Rev
50489-530-051-SPC-1002 GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
Contractor Document Number
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C
Bonnet Gasket
Spiral Wound
SS 316/ 316L Dual Stamped Graphite with Inconel Wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 F 316/ 316L Dual Stamped
Manufacturer's Alternate/ Acceptance
B
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Body Seat Ring Renewable / Integral ASTM A 182 F 316/ 316L Dual Stamped Gate ( Wedge) Solid (Note 3) ASTM A 182 F 316/ 316L Dual Stamped Body Forged ASTM A 182 F 316/ 316L Dual Stamped GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 30 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q35A, F30A
Size Range Rating Ends
Brackish Water
SW, 3000 # to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard
Type of Construction
Air Test psi (g)
51082 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
3000 2200
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C Stem Sleeve/ Nut Forged/ Machined Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel Wire Back Seat Bush UNS S32750/ 32760 Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M B Bonnet Bolted ASTM A 182 Gr F 53 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable / Integral UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Forged ASTM A 182 Gr F 53 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 31 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q35A, F30A
Size Range Rating Ends
Brackish Water
SW X SCRD NPT(F), 3000# to ASME B16.11
3000 2200 Type of Construction
51082X Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
ASME B 16.34
SHEET NO.
Face to Face dimension Manufacturer's Standard Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel Wire Back Seat Bush UNS S32750/ 32760 B Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolted ASTM A 182 Gr F 53 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable / Integral UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Forged ASTM A 182 Gr F 53 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 32 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51301
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
C13A
Size Range Rating Ends
Fuel Oil (Diesel), Inert Gas
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
450 325
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 2" - 16" 150# Special Requirements
Valve Type
API 600/ BS EN ISO 10434 API 598/ BS 6755 Pt. 1
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4) Bolted
Bonnet Gasket
Spiral Wound
Body Seat Ring
Renewable
Gate ( Wedge)
Solid (Note 3)
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 216 Gr WCB SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring 13% Cr. Steel (2" - 6") A 105 + 13% Cr. Steel Deposit (8" - 16") 13% Cr. Steel/ ASTM A 216 Gr WCB + 13% Cr. Steel Deposit ASTM A 216 Gr WCB
Manufacturer's Alternate/ Acceptance
Cast Body GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.
Page 33 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51311
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Manuf. Standard
Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
API 602/ BS EN ISO 15761 (1/2" - 1 1/2") , API 600/BS EN ISO 10434 ( 2" - 24"), API 6D / ASME B 16.34 (26" - 48") API 598/ BS 6755 Pt. 1
B
Valve Type Bolted Bonnet
Size Range
1/2" - 48"
Rating Ends
150# Special Requirements
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 150#, ASME B16.5/ B 16.47 Series A, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
450 325
Rev
50489-530-051-SPC-1002 GATE VALVE OS &Y
C15B
Piping Class
Contractor Document Number
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4)
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750 / 32760 Graphite with Inconel wire UNS S32750 / 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H
Bonnet
Bolted
ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 48")
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Body Seat Ring
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 48")
UNS S32750 / 32760
Gate ( Wedge)
Solid (Note 3)
UNS S32750 / 32760
Body
Forged, Cast
ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 48")
Manufacturer's Alternate/ Acceptance
Page 34 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 51311 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.
Page 35 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51312
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Manuf. Standard
OS &Y Bolted Bonnet
Size Range
1/2" - 48"
Rating
150# Special Requirements
API 598/ BS 6755 Pt. 1
Services / Fluids
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 150#, ASME B16.5/ B 16.47 Series A, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.
80
Air Test psi (g)
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4)
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS316L Graphite with Inconel wire SS316L ASTM A 193 Gr B7 ASTM A 194 Gr 2H
Bonnet
Bolted
ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 48")
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Gate ( Wedge)
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 48") Solid (Note 3)
Body
Forged, Cast
Body Seat Ring
B
Valve Type
API 602/ BS EN ISO 15761 (1/2" - 1 1/2") , API 600/BS EN ISO 10434 ( 2" - 24"), API 6D / ASME B 16.34 (26" - 48")
450 325
Rev
50489-530-051-SPC-1002 GATE VALVE
C15B
Testing Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Manufacturer's Alternate/ Acceptance
SS316L SS316L ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 48")
Page 36 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 51312 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.
Page 37 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51361
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S10A
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution
Size Range Rating Ends
B
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
Face to Face dimension ASME B 16.10
ASME B 16.34 425 325
Rev
50489-530-051-SPC-1002 GATE VALVE OS &Y Bolted Bonnet 2" - 12" 150# Special Requirements
Valve Type
API 600/ BS EN ISO 10434 API 598/ BS 6755 Pt. 1
Contractor Document Number
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Manufacturer's Alternate/ Acceptance
B
Body Seat Ring Renewable SS316 Gate ( Wedge) Solid (Note 3) SS316 Body Cast ASTM A 351 Gr CF8M GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 38 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51363
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Valve Type
Manuf. Standard
Testing Standard
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
S10B
Piping Class
Contractor Document Number
Bolted Bonnet
API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434( 2" - 12") API 598/ BS 6755 Pt. 1
Size Range
1/2" - 12"
Rating Ends
150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Hydrocarbon Gas / Condensate, Glycol
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
425 325
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream -
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750 / 32760 Graphite with Inconel wire UNS S32750 / 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bonnet
Bolted
A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 12")
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Gate ( Wedge)
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 12") Solid (Note 3)
Body
Forged,Cast
Body Seat Ring
Manufacturer's Alternate/ Acceptance
B
UNS S32750 / 32760 UNS S32750 / 32760 A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 12")
Page 39 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 51363 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GENERAL NOTES : GATE VALVE 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 40 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51364
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Valve Type Manuf. Standard
Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434( 2" - 12")
Size Range
1/2" - 12"
Rating Ends
150# Special Requirements
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) Flanged, 150#, ASME B16.5, RF, Finish 125 & Fuel Gas (FG) services only.
AARH
Face to Face dimension ASME B 16.10
ASME B 16.34 425 325
B
Bolted Bonnet
API 598/ BS 6755 Pt. 1
Hydrocarbon Gas / Condensate, Glycol
Rev
50489-530-051-SPC-1002 GATE VALVE OS &Y
S10B
Piping Class
Contractor Document Number
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream -
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bonnet
Bolted
A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 12")
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Body Seat Ring
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 12")
316/316L Dual Stamped (1/2" - 1 1/2") SS316L (2" - 12")
Gate ( Wedge)
Solid (Note 3)
316/316L Dual Stamped (1/2" - 1 1/2") SS316L (2" - 12")
Body
Forged,Cast
A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 12")
Manufacturer's Alternate/ Acceptance
B
Page 41 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 51364 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GENERAL NOTES : GATE VALVE 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 42 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q15A
SHEET NO. 51378 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve Type
GATE VALVE OS &Y Bolted Bonnet
Manuf. Standard
API 600/ BS EN ISO 10434
Size Range
3" - 24"
Testing Standard
BS 5154/ MSS-SP-80
Rating Ends
150# Special Requirements
Services / Fluids
Brackish Water
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
300 225 Type of Construction
Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) Monel / NI-AL-Bronze Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush Monel / NI-AL-Bronze Bonnet Bolts / Nuts (Note 6) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM B 148 UNS C95800 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable Monel / NI-AL-Bronze Gate ( Wedge) Solid (Note 5) Monel / NI-AL-Bronze Body Cast ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 4. Care should be taken to avoid galvanic corrosion by dissimlar metals. 5. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 6. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 7. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.
Page 43 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51378F
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13B (4" - 12"), F10A (2" - 24")
Valve Type
API 600/ BS EN ISO 10434
Testing Standard
BS 5154/ MSS-SP-80
Size Range Rating Ends
Services / Fluids
Brackish Water, Potable/ Fresh Water, Plant Air
Flanged, 150#, ASME B16.5, FF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154
Description
300 225 Type of Construction
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 2" - 24" 150# Special Requirements
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) Monel / NI-AL-Bronze Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush Monel / NI-AL-Bronze (Note 9) Bonnet Bolts / Nuts (Note 6) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM B 148 UNS C95800 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable Monel / NI-AL-Bronze (Note 9) Gate ( Wedge) Solid (Note 5) Monel / NI-AL-Bronze (Note 9) Body Cast ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 4. Care should be taken to avoid galvanic corrosion by dissimlar metals. 5. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 6. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 7. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor. 9. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .
B
Page 44 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51379
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Manuf. Standard
Bolted Bonnet
Size Range
1/2" - 36" 150# Special Requirements
Rating Ends
Services / Fluids
Potable/ Fresh Water, Plant Air, Hydrocarbon Oil/ Condensate, Oily Water, Effluent Water
Flanged, 150#, ASME B16.5/ B 16.47 Series A, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10 Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged / Machined Forged / Bar (No Casting) Renewable with Valve on stream -
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bolted
ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 36")
Bonnet Gasket
Flat Ring
Compressed Non Asbestos Fibre
Body Seat Ring
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 36")
UNS S32750 / 32760
Gate ( Wedge)
Solid (Note 3)
UNS S32750/ 32760
Forged/ Cast
ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 36")
Bonnet
Body
B
OS &Y
Valve Type
API 598/ BS 6755 Pt. 1
450 325
Rev
50489-530-051-SPC-1002 GATE VALVE
C15B(2" - 10"), Q15B(1/2 "- 36"), F10B (1/2" - 11/2") API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434 ( 2" - 24") API 6D/ ASME B 16.34 (26" - 36")
Testing Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Manufacturer's Alternate/ Acceptance
B
Page 45 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 51379 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE C15B(2" - 10"), GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 46 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Valve Type Manuf. Standard
Testing Standard
API 598/ BS 6755 Pt. 1
51379F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
F10B API 600/ BS EN ISO 10434 (2"-24") API 6D/ ASME B 16.34 (26" - 36")
SHEET NO.
Bolted Bonnet Size Range
2" - 36"
Rating Ends
150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Flanged, 150#, ASME B16.5/ B 16.47 Series Effluent Water, Oily Water A, FF, Finish 125 AARH ASME B 16.34 450 325 Type of Construction
Face to Face dimension ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush UNS S32750/ 32760 Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M B Bonnet Bolted ASTM A 995 Gr 5A/ 6A Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Cast ASTM A 995 Gr 5A/ 6A GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 47 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F10A(1/2" - 11/2"), Q15A(1/2" - 2") MSS-SP-80
Testing Standard
BS 5154/ MSS-SP-80
Services / Fluids
Brackish Water
Flanged, 150#, ASME B16.5 FF, Finish 125 AARH
ASME B 16.24
Face to Face dimension Manufacturer's Standard/ BS 5154
Description
350 250 Type of Construction
51380F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Screwed Bonnet 1/2" - 2" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
Size Range Rating Ends
80
Air Test psi (g)
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Malleable Iron /Aluminium / Steel / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined To Manufacturer's standard Stem Forged / Bar (No Casting) To Manufacturer's standard Gland Packing Renewable with Valve on stream To Manufacturer's standard (Non Asbestos) Back Seat Bush ASTM B62 C83600 Bonnet Bolts / Nuts (Note 4) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Screwed ASTM B62 C83600 Bonnet Gasket Body Seat Ring Renewable / Integral ASTM B62 C83600 Gate ( Wedge) Solid (Note 3) ASTM B62 C83600 Body Cast ASTM B62 C83600 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 6. Care should be taken to avoid galvanic corrosion by dissimlar metals. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.
Page 48 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13B
Valve Type
MSS-SP-80
Testing Standard
BS 5154/ MSS-SP-80
Size Range Rating Ends
Services / Fluids
Potable/ Fresh Water, Plant Air
SCRF, 150# to NPT(F), ASME B 1.20.1
ASME B 16.24
Face to Face dimension Manufacturer's Standard/ BS 5154
Description
350 250 Type of Construction
51380S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Screwed Bonnet 1/2" - 3" 150# Special Requirements
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
80
Air Test psi (g)
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Malleable Iron /Aluminium / Steel / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined To Manufacturer's standard Stem Forged / Bar (No Casting) To Manufacturer's standard Gland Packing Renewable with Valve on stream To Manufacturer's standard (Non Asbestos) Back Seat Bush ASTM B62 C83600 Bonnet Bolts / Nuts (Note 4) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Screwed ASTM B62 C83600 Bonnet Gasket Body Seat Ring Renewable / Integral ASTM B62 C83600 Gate ( Wedge) Solid (Note 3) ASTM B62 C83600 Body Cast ASTM B62 C83600 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 6. Care should be taken to avoid galvanic corrosion by dissimlar metals. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.
Page 49 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Testing Standard
API 600/ BS EN ISO 10434
51398 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
N10C Valve Type
Manuf. Standard
SHEET NO.
Bolted Bonnet Size Range
8" - 16"
API 598/ BS 6755 Pt. 1
Rating Ends
150# Special Requirements
Off Spec Crude Oil
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
450 325 Type of Construction
Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) INCONEL 625 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush INCONEL 625 Bonnet Bolts / Nuts ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable (8" - 16") INCONEL 625 Gate ( Wedge) Solid (Note 3) INCONEL 625 Body Cast ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 50 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51399
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 N10B ( 0.5" - 20") N10C (0.5" - 6")
Piping Class
Manuf. Standard B
Testing Standard
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
Valve Type
API 602 / BS EN ISO 15761(1/2" - 1 1/2"), API 600 / BS EN ISO 10434(2"-20")
Contractor Document Number
Bolted Bonnet Size Range
1/2" - 20"
API 598/ BS 6755 Pt. 1
Rating Ends
150# Special Requirements
Off Spec Crude Oil
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
B
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
450 325
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet Bonnet Gasket
Cast / Fabricated Corrosion Resistant Forged / Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted Flat Ring
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C INCONEL 625 Graphite with Inconel wire INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B564-UNS N06625 Compressed Non Asbestos Fibre
Body Seat Ring
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 6")
INCONEL 625
Manufacturer's Alternate/ Acceptance
Gate ( Wedge) Solid (Note 3) INCONEL 625 Body Forged ASTM B564-UNS N06625 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 51 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 C35B
Piping Class
Manuf. Standard
Testing Standard Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
API 602/ BS EN ISO 15761(1/2" - 1 1/2"), API 600/ BS EN ISO 10434(2" - 16") API 598/ BS 6755 Pt. 1 Hydrocarbon Oil / Condensate, Glycol ASME B 16.34 1125 825
51411 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 1/2" - 16"
Valve Type
Size Range
300#
Rating Ends Special Requirements Flanged, 300#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4)
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H
Bonnet
Bolted
ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 16")
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Gate ( Wedge)
Renewable / Integral(1/2" - 1 1/2") Renewable (2" -1 6") Solid (Note 3)
Body
Forged/ Cast
Body Seat Ring
SHEET NO.
Manufacturer's Alternate/ Acceptance
UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 16")
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor. Page 52 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51461
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S30A
Size Range Rating Ends
Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1100 800
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 2" - 12" 300# Special Requirements
Valve Type
API 600/ BS EN ISO 10434 API 598/ BS 6755 Pt. 1
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted
Bonnet Gasket
Spiral Wound
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring SS 316 SS 316 ASTM A 351 Gr CF8M
Manufacturer's Alternate/ Acceptance
B
Renewable Body Seat Ring Solid (Note 3) Gate ( Wedge) Cast Body GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 53 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51463
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 S30B
Piping Class
Manuf. Standard
Testing Standard Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434( 2" - 16") API 598/ BS 6755 Pt. 1
Rev
50489-530-051-SPC-1002
B
Valve Type
GATE VALVE OS &Y Bolted Bonnet
Size Range
1/2" - 16"
Rating Ends
300# Special Requirements
Hydrocarbon Gas / Condensate, Glycol
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1100 800
Contractor Document Number
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream -
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750 / 32760 Graphite with Inconel wire UNS S32750 / 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bonnet
Bolted
A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 16")
Bonnet Gasket
Spiral Wound
SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Body Seat Ring
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 16")
UNS S32750 / 32760
Gate ( Wedge)
Solid (Note 3)
UNS S32750 / 32760
Body
Forged,Cast
A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 16")
Manufacturer's Alternate/ Acceptance
B
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor. Page 54 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Manuf. Standard
Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
SHEET NO. 51478 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
Q35A Valve Type
API 600/ BS EN ISO 10434 (3" -24"), API 6D/ASME B 16.34 (26" - 32") BS 5154/ MSS-SP-80
Size Range
3" - 32"
Rating Ends
300# Special Requirements
Brackish Water
Flanged, 300#, ASME B16.5 / B 16. 47 A, RF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154
775 575 Type of Construction
Bolted Bonnet
Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) Monel / NI-AL-Bronze Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush Monel / NI-AL-Bronze Bonnet Bolts / Nuts (Note 6) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM B 148 UNS C95800 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable Monel / NI-AL-Bronze Gate ( Wedge) Solid (Note 5) Monel / NI-AL-Bronze Body Cast ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 4. Care should be taken to avoid galvanic corrosion by dissimlar metals. 5. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 6. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 7. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.
Page 55 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
F30A API 600/ BS EN ISO 10434 BS 5154/ MSS-SP-80
Size Range Rating Ends Flanged, 300#, ASME B16.5, FF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154
Type of Construction
Air Test psi (g)
51478F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 2" - 24" 300# Special Requirements
Valve Type
Brackish Water
775 575
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) Monel / NI-AL-Bronze Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush Monel / NI-AL-Bronze Bonnet Bolts / Nuts (Note 6) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM B 148 UNS C95800 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable Monel / NI-AL-Bronze Gate ( Wedge) Solid (Note 5) Monel / NI-AL-Bronze Body Cast ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 4. Care should be taken to avoid galvanic corrosion by dissimlar metals. 5. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 6. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 7. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.
Page 56 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51479
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Manuf. Standard
Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
B
OS &Y
Valve Type
Bolted Bonnet Size Range
1/2" - 24"
Rating Ends
300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Hydrocarbon Oil / Gas / Condensate, Oily Water, Glycol
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream -
Bonnet
Bolted
Bonnet Gasket
Gate ( Wedge)
Flat Ring Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 24") Solid (Note 3)
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 24") Compressed Non Asbestos Fibre
Body
Forged,Cast
Body Seat Ring
Rev
50489-530-051-SPC-1002 GATE VALVE
C35B(2" - 14 "), S30B(1/2"-11/2"), Q35B(2" - 24"), F30B(1/2" - 11/2") API 602/ BS EN ISO 15761 (1/2"-1 1/2"), API 600/ BS EN ISO 10434(2"-24") API 598/ BS 6755 Pt. 1
1125 825
Contractor Document Number
Manufacturer's Alternate/ Acceptance
B
UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 24")
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor. Page 57 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO. 51479F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
F30B Valve Type
Bolted Bonnet
, API 600 / BS EN ISO 10434
Size Range
2" - 24"
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
300# Special Requirements
Services / Fluids
Hydrocarbon Oil / Gas / Condensate, Oily Water, Glycol
Flanged, 300#, ASME B16.5, FF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
1125 825 Type of Construction
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush UNS S32750/ 32760 B Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolted ASTM A 995 Gr 5A/ 6A Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring UNS S32750/ 32760 Renewable Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Cast ASTM A 995 Gr 5A/ 6A GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 58 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q35A API 600/ BS EN ISO 10434
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Brackish Water
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Description
1125 825 Type of Construction
Size Range Rating Ends
Air Test psi (g)
51482 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 2" 300# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Ductile Iron/ Malleable Iron / Cast Steel Handwheel Cast / Fabricated Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush UNS S32750/ 32760 B Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolted ASTM A 995 Gr 5A/ 6A Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Cast ASTM A 995 Gr 5A/ 6A GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 59 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Testing Standard
51498 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
N30C Valve Type
Manuf. Standard
SHEET NO.
API 600/ BS EN ISO 10434
Bolted Bonnet Size Range
8" - 16"
API 598/ BS 6755 Pt. 1
Rating Ends
300# Special Requirements
Off Spec Crude Oil
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
1125 825 Type of Construction
Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) INCONEL 625 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush INCONEL 625 Bonnet Bolts / Nuts ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Renewable Body Seat Ring INCONEL 625 Gate ( Wedge) Solid (Note 3) INCONEL 625 Body Cast ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 60 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51499
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Manuf. Standard
Testing Standard
N30B (0.5" - 16") N30C (0.5" - 6" API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434 B (2"-16")
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
Valve Type
Bolted Bonnet Size Range
1/2" - 16"
API 598/ BS 6755 Pt. 1
Rating Ends
300# Special Requirements
Off Spec Crude Oil
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
B
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
1125 825
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet Bonnet Gasket
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted Flat Ring Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 6") Solid (Note 3) Forged
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C INCONEL 625 Graphite with Inconel wire INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B564-UNS N06625 Compressed Non Asbestos Fibre
Body Seat Ring
Manufacturer's Alternate/ Acceptance
INCONEL 625
Gate ( Wedge) INCONEL 625 Body ASTM B564-UNS N06625 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 61 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Manuf. Standard
Testing Standard Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Valve Type
API 602/ BS EN ISO 15761(1/2" - 1 1/2"), API 600/ BS EN ISO 10434 (2" - 24") API 598/ BS 6755 Pt. 1 Hydrocarbon Gas/ Oil/ Condensate, Glycol ASME B 16.34 2225 1650
51511 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
C65B
Piping Class
SHEET NO.
Bolted Bonnet Size Range
1/2" - 24"
Rating 600# Ends Special Requirements Flanged, 600#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4)
Bonnet
Bolted
Bonnet Gasket
Spiral Wound
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 24") SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Body Seat Ring
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 24")
Gate ( Wedge)
Solid (Note 3)
Body
Forged/ Cast
Manufacturer's Alternate/ Acceptance
UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 24")
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor. Page 62 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51561
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S60A
Size Range Rating Ends
Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution
Flanged, 600#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
2175 1600
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y Bolted Bonnet 2" - 12" 600# Special Requirements
Valve Type
API 600/ BS EN ISO 10434 API 598/ BS 6755 Pt. 1
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted
B
Bonnet Gasket
Spiral Wound
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring SS 316 SS 316 ASTM A 351 Gr CF8M
Body Seat Ring Renewable Gate ( Wedge) Solid (Note 3) Body Cast GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.
Page 63 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51579
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Rev
50489-530-051-SPC-1002
B
GATE VALVE OS &Y
C65B
Piping Class
Contractor Document Number
Valve Type
API 602/ BS EN ISO 15761(1/2" - 1 1/2"), API 600/ BS EN ISO 10434 (2" - 24")
Size Range
1/2" - 24"
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
600# Special Requirements
Services / Fluids
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 600#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
2225 1650
Bolted Bonnet
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream -
Bonnet
Bolted
Bonnet Gasket
Spiral Wound
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 24") SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring
Body Seat Ring
Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 24")
Gate ( Wedge)
Solid (Note 3)
Body
Forged/ Cast
Manufacturer's Alternate/ Acceptance
B
UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 24")
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor. Page 64 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
51779
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GATE VALVE Piping Class
Q95B OS &Y
Valve Type
Manuf. Standard
Testing Standard
API 602/ BS EN ISO 15761 (1/2"-1 1/2"), API 600/ BS EN ISO 10434(2") API 598/ BS 6755 Pt. 1
Size Range
1/2" - 2"
Rating Ends
1500# Special Requirements
Effluent Water, Treated Water
Flanged, 1500#, ASME B16.5, RTJ, Finish 32 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Bolted Bonnet
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
5625 4125
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream -
Bonnet
Bolted
Bonnet Gasket
Gate ( Wedge)
Ring Type Renewable / Integral(1/2" - 1 1/2") Renewable (2" ) Solid (Note 3)
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2") Super Duplex Oval Shape Gasket
Body
Forged, Cast
Body Seat Ring
Manufacturer's Alternate/ Acceptance
B
UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2")
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor. Page 65 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52001
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
C13A
Size Range Rating Ends
Fuel Oil (Diesel), Inert Gas
SW, 3000# to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Std. Air Test psi (g)
Type of Construction
Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts Bolted Bonnet Bonnet Gasket
Spiral Wound
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
2975 2175
Contractor Document Number
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105 Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Renewable / Integral 13% Cr. Steel + Stellite Facing Seat Ring Loose (Spherical/ Ball/ Plug) ASTM A 105 + Stellite Facing Disc Forged ASTM A 105 Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.
Page 66 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52061
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S10A, S30A, S60A
Size Range Rating Ends
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor
SW, 3000 # to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Std.
2900 2125
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream Bolted
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 F 316/ 316L Dual Stamped
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Manufacturer's Alternate/ Acceptance
B
Renewable / Integral ASTM A 182 F 316/ 316L Dual Stamped Seat Ring Loose (Spherical/ Ball/ Plug) ASTM A 182 F 316/ 316L Dual Stamped Disc Forged ASTM A 182 F 316/ 316L Dual Stamped Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 67 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q35A, F30A
Size Range Rating Ends
Brackish Water
SW, 3000 # to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Type of Construction
Air Test psi (g)
52082 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
3000 2200
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast / Fabricated Malleable Iron / Ductile Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate Yoke Bush / Retaining Nut Forged/ Machined ASTM A439 Type D-2 / D-2C Forged / Bar (No Casting) Stem UNS S32750/ 32760 Renewable with valve on stream Gland Packing Graphite with Inconel Wire Back Seat Bush UNS S32750/ 32760 B ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolts / Nuts Bolted Bonnet ASTM A 182 Gr F 53 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable / Integral Seat Ring UNS S32750/ 32760 Loose (Spherical/ Ball/ Plug) Disc UNS S32750/ 32760 Forged Body ASTM A 182 Gr F 53 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 68 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52301
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13A BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Fuel Oil (Diesel), Inert Gas
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
450 325
Size Range Rating Ends
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" - 16" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream (Note 3) Bolted
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 216 Gr WCB
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring
Renewable
Disc
Loose (Spherical/ Ball/ Plug)
Manufacturer's Alternate/ Acceptance
13% Cr. Steel (2" - 6") ASTM A105 + 13% Cr. Steel Deposit (8" - 16") 13% Cr. Steel/ ASTM A 216 Gr WCB + 13% Cr. Steel Deposit ASTM A 216 Gr WCB
Cast Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.
Page 69 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Valve Type API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 16")
Size Range
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
Manuf. Standard
Pressure -Temperature Rating
Description
450 325
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Bolted Bonnet 1/2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
52311
GLOBE VALVE OS &Y
C15B
Piping Class
SHEET NO.
ASME B 16.10 Air Test psi (g)
Type of Construction
Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S 32750 / 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 16")
Bonnet
Bolted
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring
Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above)
UNS S32750/ 32760
Disc
Loose (Spherical/ Ball/ Plug)
UNS S32750/ 32760
Body
Forged (1/2" - 1 1/2") / Cast (2" & Above)
ASTM A 105N (1/2" - 1 1/2")/ ASTM A 216 Gr WCB (2" - 16")
Page 70 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 52311 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.
Page 71 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Valve Type API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 16")
Size Range
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Hydrocarbon Gas/ Oil/ Condensate
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
Manuf. Standard
Pressure -Temperature Rating
Description
450 325
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Bolted Bonnet 1/2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This Valve Data Sheet shall be applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) services only.
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
52312
GLOBE VALVE OS &Y
C15B
Piping Class
SHEET NO.
ASME B 16.10 Air Test psi (g)
Type of Construction
Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316L Graphite with Inconel Wire SS 316L ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 16")
Bonnet
Bolted
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring
Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above)
SS 316L
Disc
Loose (Spherical/ Ball/ Plug)
SS 316L
Body
Forged (1/2" - 1 1/2") / Cast (2" & Above)
ASTM A 105N (1/2" - 1 1/2")/ ASTM A 216 Gr WCB (2" - 16")
Page 72 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 52312 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.
Page 73 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52361
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S10A BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
425 325
Size Range Rating Ends
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" - 12" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream Bolted
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Manufacturer's Alternate/ Acceptance
B
Renewable SS 316 Seat Ring Loose (Spherical/ Ball/ Plug) SS 316 Disc Cast ASTM A 351 Gr CF8M Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 74 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Valve Type
Size Range
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Hydrocarbon Gas/Condensate, Glycol
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
Pressure -Temperature Rating
425 325
150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
ASME B 16.10 Air Test psi (g)
80
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy
Forged/ Machined
ASTM A 439 Type D-2/ D-2C
Forged / Bar (No Casting) Renewable with valve on stream -
UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 GR F 316/316L Dual Stamped (1/2" 1 1/2") / ASTM A 351 Gr CF8M (2" - 12") Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Bolted
Bonnet Gasket
Spiral Wound
Seat Ring Disc Body
B
1/2" - 12"
Description
Bonnet
Rev
50489-530-051-SPC-1002
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Bolted Bonnet
API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')
Manuf. Standard
52363
GLOBE VALVE OS &Y
S10B
Piping Class
SHEET NO.
Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above) Loose (Spherical/ Ball/ Plug) Forged (1/2" - 1 1/2") / Cast (2" - 12")
Manufacturer's Alternate/ Acceptance
B
UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 GR F 316/316L Dual Stamped (1/2" 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor. Page 75 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52364
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y
S10B
Piping Class
Contractor Document Number
Valve Type
Bolted Bonnet
API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')
Size Range
1/2" - 12"
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
150# Special Requirements
Services / Fluids
Hydrocarbon Gas/Condensate
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
Manuf. Standard
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Pressure -Temperature Rating
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
425 325
2. This Valve Data Sheet shall be applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) services only.
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream -
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bonnet
Bolted
ASTM A 182 GR F 316/316L Dual Stamped (1/2" - 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring Disc Body
Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above) Loose (Spherical/ Ball/ Plug) Forged (1/2" - 1 1/2") / Cast (2" - 12")
Manufacturer's Alternate/ Acceptance
B
SS 316L SS 316L ASTM A 182 GR F 316/316L Dual Stamped (1/2" - 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor. Page 76 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q15A BS 1873
Testing Standard
BS 5154/ MSS-SP-80
Services / Fluids
Brackish Water
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154 / ASME B 16.10
Description
300 225 Type of Construction
52378 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 3" - 16" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
Size Range Rating Ends
80
Air Test psi (g)
Material of Construction
Manufacturer's Alternate/ Acceptance
Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate ASTM A 439 Type D-2/ D-2C Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Monel / NI-AL-Bronze Stem Renewable with valve open on stream Gland Packing Graphite with Inconel wire Forged /Machined Monel/ NI-AL-Bronze Back Seat Bush (Note 3) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bolted Bonnet ASTM B 148 UNS C95800 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable Seat Ring Monel/ NI-AL-Bronze Loose (Spherical/ Ball/ Plug) Disc Monel/ NI-AL-Bronze Cast Body ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.
Page 77 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52378F
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13B (4" - 12"), F10A ( 2" - 16") BS 1873
Testing Standard
BS 5154/ MSS-SP-80
Size Range Rating Ends
Services / Fluids
Brackish Water, Potable/ Fresh Water, Plant Air
Flanged, 150#, ASME B16.5, FF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154 / ASME B 16.10
Description
300 225
Air Test psi (g)
Type of Construction Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve open on stream Forged /Machined (Note 3) Bolted Flat Ring Renewable Loose (Spherical/ Ball/ Plug) Cast (Straight Pattern)
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" - 16" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C Monel / NI-AL-Bronze Graphite with Inconel wire Monel/ NI-AL-Bronze (Note 8) ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B 148 UNS C95800 Compressed Non-Asbetos Fibre Monel/ NI-AL-Bronze (Note 8) Monel/ NI-AL-Bronze (Note 8) ASTM B 148 UNS C95800
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet Bonnet Gasket Seat Ring Disc Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor. 8. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .
Page 78 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C15B ( 1/2" - 12"), F10B (1/2" - 11/2"), Q15B (1/2" - 16")
API 598/ BS 6755 Pt. 1
Rating Ends
Hydrocarbon Oil/ Condensate, Oily Water, Glycol, Effluent Water
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
Size Range
1/2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged / Bar (No Casting) Renewable with valve on stream -
Bonnet
Bolted
Bonnet Gasket
Flat Ring Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above) Loose (Spherical/ Ball/ Plug) Forged (1/2" - 11/2") / Cast (2" - 16")
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S 32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2") ASTM A 995 Gr 5A/ 6A (2" - 16") Compressed Non-Asbetos Fibre
Seat Ring Disc Body
B
Face to Face dimension
ASME B 16.34
450 325
Rev
50489-530-051-SPC-1002
OS &Y
Testing Standard
Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Bolted Bonnet
API 602 / BS EN ISO 15761(1/2" - 1 1/2") BS 1873 (2" - 16")
Pressure -Temperature Rating
52379
GLOBE VALVE Valve Type
Manuf. Standard
Services / Fluids
SHEET NO.
Manufacturer's Alternate/ Acceptance
B
UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 16")
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor. Page 79 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 F10B
Piping Class
BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Effluent Water, Oily Water
Flanged, 150#, ASME B16.5, FF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Description
450 325
Size Range Rating Ends
Air Test psi (g)
Type of Construction
Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush Bonnet Bolts / Nuts
52379F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
80 Material of Construction Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S 32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bonnet
Bolted
ASTM A 995 Gr 5A/ 6A
Bonnet Gasket Seat Ring Disc
Flat Ring Renewable Loose (Spherical/ Ball/ Plug)
Compressed Non-Asbetos Fibre UNS S32750/ 32760 UNS S32750/ 32760
Body
Cast
ASTM A 995 Gr 5A/ 6A
Manufacturer's Alternate/ Acceptance
B
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 80 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52380S
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13B MSS-SP-80
Testing Standard
BS 5154/ MSS-SP-80
Size Range Rating Ends
Services / Fluids
Potable/ Fresh Water, Plant Air
SCRF, 3000# to NPT, ASME B 1.20.1
ASME B 16.24
Face to Face dimension Manufacturer's Std./ BS 5154
Description
350 250
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Screwed Bonnet 1/2" - 3" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80
Air Test psi (g)
Type of Construction
Material of Construction
Cast / Fabricated Corrosion Resistant
Malleable Iron /Aluminium / Steel / Cast Steel SS/ Ni Alloy To Manufacturer's standard To Manufacturer's standard To Manufacturer's standard ASTM B62 UNS C83600 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B62 UNS C83600 ASTM B62 UNS C83600 ASTM B62 UNS C83600 ASTM B62 UNS C83600
Manufacturer's Alternate/ Acceptance
Handwheel Name Plate Yoke Bush / Retaining Nut Nickel or Copper Alloy Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts Bonnet Cast / Screwed Bonnet Gasket Renewable / Integral Seat Ring Loose (Spherical/ Ball/ Plug) Disc Cast Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.
Page 81 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52380F
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F10A (1/2" - 11/2"), Q15A (1/2" - 2") MSS-SP-80
Testing Standard
BS 5154/ MSS-SP-80
Size Range Rating Ends
Services / Fluids
Potable/ Fresh Water, Plant Air
Flanged, 150#, ASME B16.5, FF, Finish 125 AARH
ASME B 16.24
Face to Face dimension Manufacturer's Std./ BS 5154
Description
350 250
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Screwed Bonnet 1/2" - 2" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80
Air Test psi (g)
Type of Construction
Material of Construction
Cast / Fabricated Corrosion Resistant
Malleable Iron /Aluminium / Steel / Cast Steel SS/ Ni Alloy To Manufacturer's standard To Manufacturer's standard To Manufacturer's standard ASTM B62 UNS C83600 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B62 UNS C83600 Compressed Non-Asbetos Fibre ASTM B62 UNS C83600 ASTM B62 UNS C83600 ASTM B62 UNS C83600
Manufacturer's Alternate/ Acceptance
Handwheel Name Plate Yoke Bush / Retaining Nut Nickel or Copper Alloy Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts Bonnet Cast / Screwed Bonnet Gasket Flat Ring Renewable / Integral Seat Ring Loose (Spherical/ Ball/ Plug) Disc Cast Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.
Page 82 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO. 52399 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y
N10B (0.5" - 16") N10C (0.5" - 6") Valve Type
Manuf. Standard
API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 16") B
Bolted Bonnet Size Range
1/2" - 16"
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Off Spec Crude Oil
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
ASME B 16.34
450 325 Type of Construction
B
150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate Yoke Bush/ Retaining Nut ASTM A 439 Type D-2 / D-2C Forged / Bar (No Casting) Stem INCONEL 625 Renewable with Valve on stream Gland Packing Graphite with Inconel wire Back Seat Bush INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bonnet Bolted ASTM B564-UNS N06625 Bonnet Gasket Flat Ring Compressed Non-Asbetos Fibre Renewable / Integral Body Seat Ring INCONEL 625 Loose (Spherical/ Ball/ Plug) Disc INCONEL 625 Forged ASTM B 564-UNS N06625 Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 83 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Valve Type API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873(2" - 12")
Size Range
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Hydrocarbon Oil/ Condensate, Glycol
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
Manuf. Standard
Pressure -Temperature Rating
1125 825
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Bolted Bonnet 1/2" - 12" 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
52411
GLOBE VALVE OS &Y
C35B
Piping Class
SHEET NO.
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream (Note 4)
Bonnet
Bolted
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S32750 / 32760 Graphite with Inconel Wire UNS S32750 / 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 12")
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring
Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above)
UNS S32750 / 32760
Disc
Loose (Spherical/ Ball/ Plug)
UNS S32750 / 32760
Body
Forged (1/2" - 1 1/2") / Cast (2" - 12")
ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 12")
Manufacturer's Alternate/ Acceptance
Page 84 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 52411 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.
Page 85 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52461
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S30A BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1100 800
Size Range Rating Ends
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" - 12" 300# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream Bolted
Malleable Iron / Ductile Iron /Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M
B
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Renewable SS 316 Seat Ring Loose (Spherical/ Ball/ Plug) SS 316 Disc Cast ASTM A 351 Gr CF8M Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 86 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
52463 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489
GLOBE VALVE OS &Y
S30B
Piping Class
Valve Type
Bolted Bonnet
API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')
Size Range
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Hydrocarbon Gas/Condensate, Glycol
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
Manuf. Standard
SHEET NO.
Pressure -Temperature Rating
1100 800
300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
1/2" - 12"
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream -
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bonnet
Bolted
ASTM A 182 GR F 316/316L Dual Stamped (1/2" - 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring
Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above)
UNS S32750/ 32760
Disc
Loose (Spherical/ Ball/ Plug)
UNS S32750/ 32760
Body
Forged (1/2" - 1 1/2") / Cast (2" - 12")
ASTM A 182 GR F 316/316L Dual Stamped (1/2" - 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")
Manufacturer's Alternate/ Acceptance
B
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor. Page 87 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q35A BS 1873
Testing Standard
BS 5154/ MSS-SP-80
Services / Fluids
Brackish Water
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154 / ASME B 16.10
Description
775 575 Type of Construction
52478 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 3" - 12" 300# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
Size Range Rating Ends
80
Air Test psi (g)
Material of Construction
Manufacturer's Alternate/ Acceptance
Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate ASTM A 439 Type D-2/ D-2C Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Monel/ Ni-Al-Bronze Stem Renewable with valve open on stream Gland Packing Graphite with Inconel wire Forged /Machined Monel/ Ni-Al-Bronze Back Seat Bush (Note 3) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bolted Bonnet ASTM B 148 UNS C95800 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable Monel/ Ni-Al-Bronze Seat Ring Loose (Spherical/ Ball/ Plug) Monel/ Ni-Al-Bronze Disc Cast Body ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.
Page 88 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F30A BS 1873
Testing Standard
BS 5154/ MSS-SP-80
Services / Fluids
Brackish Water
Flanged, 300#, ASME B16.5, FF, Finish 125 AARH
ASME B 16.24
Face to Face dimension BS 5154 / ASME B 16.10
Description
775 575 Type of Construction
52478F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" - 12" 300# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
Size Range Rating Ends
80
Air Test psi (g)
Material of Construction
Manufacturer's Alternate/ Acceptance
Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate ASTM A 439 Type D-2/ D-2C Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Monel/ Ni-Al-Bronze Stem Renewable with valve open on stream Gland Packing Graphite with Inconel wire Forged /Machined Monel/ Ni-Al-Bronze Back Seat Bush (Note 3) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bolted Bonnet ASTM B 148 UNS C95800 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable Monel/ Ni-Al-Bronze Seat Ring Loose (Spherical/ Ball/ Plug) Monel/ Ni-Al-Bronze Disc Cast Body ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.
Page 89 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE
C35B ( 1/2" - 10"), F30B ( 1/2" - 11/2"), Q35B ( 1/2" - 12")
Piping Class
OS &Y
Valve Type
Bolted Bonnet
API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 12")
Size Range
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Hydrocarbon Oil/ Condensate, Oily Water, Glycol, Effluent Water
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
Pressure -Temperature Rating
1125 825
1/2" - 12" 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged / Bar (No Casting) Renewable with valve on stream -
Bonnet
Bolted
Bonnet Gasket Seat Ring Disc
Flat Ring Renewable Loose (Spherical/ Ball/ Plug) Forged (1/2" - 1 1/2") / Cast (2" - 12")
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750 / 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 12") ASTM A 995 Gr 5A/ 6A (2" - 12") Compressed Non-Asbetos Fibre UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 12")/ ASTM A 995 Gr 5A/ 6A (2" - 12")
Body
52479
VALVE MATERIAL SPECIFICATION
14050489
Manuf. Standard
SHEET NO.
Manufacturer's Alternate/ Acceptance
B
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 90 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
SHEET NO. 52479F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE Piping Class
F30B
Manuf. Standard
BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Effluent Water, Oily Water
OS &Y
Valve Type
Bolted Bonnet 2" - 12" 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Size Range Rating Ends Flanged, 300#, ASME B16.5, FF, Finish 125 AARH Face to Face dimension
Pressure -Temperature Rating
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
1125 825
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged / Bar (No Casting) Renewable with valve on stream -
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
B
Bonnet
Bolted
ASTM A 995 Gr 5A/ 6A
Bonnet Gasket Seat Ring Disc
Flat Ring Renewable Loose (Spherical/ Ball/ Plug)
Compressed Non-Asbetos Fibre UNS S32750/ 32760 UNS S32750/ 32760
Body
Cast
ASTM A 995 Gr 5A/ 6A
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 91 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52482
KOC Contract No 14050489 Q35A
Piping Class
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" 300# Special Requirements
Valve Type
Manuf. Standard
BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Brackish Water
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Contractor Document Number VALVE MATERIAL SPECIFICATION
1125 825
Size Range Rating Ends
Air Test psi (g)
Type of Construction
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
B
Bonnet
Forged/ Cast, Bolted
ASTM A 995 Gr 5A/ 6A
Bonnet Gasket Seat Ring Disc
Flat Ring Renewable Loose (Spherical/ Ball/ Plug)
Compressed Non-Asbetos Fibre UNS S32750/ 32760 UNS S32750/ 32760
Body
Cast
ASTM A 995 Gr 5A/ 6A
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 92 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Manuf. Standard
N30B (0.5" - 12') N30C (0.5" - 6") API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 12") B
Valve Type
Size Range
Rev
50489-530-051-SPC-1002
B
1/2" - 12"
Rating Ends
Services / Fluids
Oily Water
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
Description
Contractor Document Number
Bolted Bonnet
API 598/ BS 6755 Pt. 1
Hydro Test Pressure Body psi (g) Seat psi (g)
52499
GLOBE VALVE OS &Y
Testing Standard
Pressure -Temperature Rating
SHEET NO.
B
300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension ASME B 16.34
1125 825 Type of Construction
ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate Yoke Bush/ Retaining Nut ASTM A 439 Type D-2 / D-2C Forged / Bar (No Casting) Stem INCONEL 625 Renewable with Valve on stream Gland Packing Graphite with Inconel wire Back Seat Bush INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bonnet Bolted ASTM B564-UNS N06625 Flat Ring Compressed Non-Asbetos Fibre Bonnet Gasket Renewable Body Seat Ring INCONEL 625 Loose (Spherical/ Ball/ Plug) Disc INCONEL 625 Forged ASTM B564-UNS N06625 Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 93 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489
Valve Type
Size Range
Testing Standard
API 598/ BS 6755 Pt. 1
Rating Ends
Services / Fluids
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 600#, ASME B16.5, RF, Finish 125 AARH
Pressure -Temperature Rating
2225 1650
Rev
50489-530-051-SPC-1002
B
1/2" - 12" 600# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Bolted Bonnet
API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')
Manuf. Standard
52511
GLOBE VALVE OS &Y
C65B
Piping Class
SHEET NO.
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream (Note 3)
Bonnet
Bolted
Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 12")
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring
Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above)
UNS S32750/ 32760
Disc
Loose (Spherical/ Ball/ Plug)
UNS S32750/ 32760
Body
Forged (1/2" - 1 1/2") / Cast (2" - 12")
ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 12")
Manufacturer's Alternate/ Acceptance
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor. Page 94 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
52561
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S60A BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor
Flanged, 600#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
2175 1600
Size Range Rating Ends
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
GLOBE VALVE OS &Y Bolted Bonnet 2" - 12" 600# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet
Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream Bolted
Malleable Iron / Ductile Iron /Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Manufacturer's Alternate/ Acceptance
B
Renewable SS 316 Seat Ring Loose (Spherical/ Ball/ Plug) SS 316 Disc Cast ASTM A 351 Gr CF8M Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 95 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 C65B
Piping Class
BS 1873
Testing Standard
API 598/ BS 6755 Pt. 1
Size Range Rating Ends
Services / Fluids
Hydrocarbon Gas/Oil/ Condensate, Oily Water
Flanged, 600#, ASME B16.5, RF, Finish 125 AARH
2225 1650
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Face to Face dimension
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
52579
GLOBE VALVE OS &Y Bolted Bonnet 2" - 6" 600# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Valve Type
Manuf. Standard
Pressure -Temperature Rating
SHEET NO.
ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts
Cast / Fabricated Corrosion Resistant Forged / Bar (No Casting) Renewable with valve on stream -
Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M
Bonnet
Bolted
ASTM A 995 Gr 5A/ 6A
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Seat Ring Disc
Renewable Loose (Spherical/ Ball/ Plug)
UNS S32750/ 32760 UNS S32750/ 32760
Body
Cast
ASTM A 995 Gr 5A/ 6A
Manufacturer's Alternate/ Acceptance
B
GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.
Page 96 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53001
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
C13A API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Size Range Rating Ends SW, 3000# to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard. Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 800# Special Requirements
Valve Type
Fuel Oil(Diesel), Inert Gas
2975 2175
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Body Piston Seat Ring Spring Cover Guide
Forged Lift Type Renewable / Integral Bolted Forged / Bar
Cover Gasket
Spiral Wound
ASTM A105 ASTM A105 + Stellite facing 13% Cr. Steel + Stellite facing Inconel X-750 ASTM A105 13% Cr. Steel SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 97 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53061
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S10A,S30A, S60A API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Size Range Rating Ends
SW, 3000 # to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard. Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 800# Special Requirements
Valve Type
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution,Scale Inhibitor
2900 2125
Contractor Document Number
80
Description
Type of Construction
Material of Construction
Body Piston Seat Ring Spring Cover Guide
Forged Lift Type Renewable / Integral Bolted Forged / Bar
Cover gasket
Spiral Wound
ASTM A 182 F 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped Inconel X-750 ASTM A 182 F 316/ 316L Dual Stamped SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts B Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 98 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53061Z
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S30A, S60A BS 1868
Testing Standard
API 598/ BS 6755 Part-1
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution
SW, 3000 # to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard.
2900 2125
Size Range Rating Ends
Air Test psi (g)
B
80
Description
Type of Construction
Material of Construction
Body Seat Ring Disc Cover Hinge Hinge Pin
Forged Renewable / Integral Bolted
Cover gasket
Spiral Wound
ASTM A 182 F 316/ 316L Dual Stamped 316/ 316L Dual Stamped 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Forged / Bar
Rev
50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 1/2" - 11/2" 800# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts B Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 99 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53082
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q35A, F30A
Size Range Rating Ends
Brackish Water
SW, 3000 # to ASME B16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard. Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 800# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
3000 2200
Contractor Document Number
80
Type of Construction
Material of Construction
Forged Lift Type Renewable / Integral Bolted Forged / Bar Flat Ring Corrosion Resistant
ASTM A 182 Gr F 53 ASTM A 182 Gr F 53 ASTM A 182 Gr F 53 Inconel X-750 ASTM A 182 Gr F 53 UNS S32750/ 32760 Compressed Non Asbestos Fibre ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Body Piston Seat Ring Spring Cover Guide Cover gasket Cover Bolts / Nuts B Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 100 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53301
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 C13A
Piping Class
BS 1868
Testing Standard
API 598 / BS 6755 Part-1
Size Range Rating Ends
Services / Fluids
Fuel Oil(Diesel), Inert Gas
Flanged, 150 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
450 325
Air Test psi (g)
Type of Construction
Material of Construction ASTM A 216 Gr WCB 13% Cr. Steel (2" - 6") ASTM A105 + 13% Cr. Steel Deposit (8" - 16")
Body Seat Ring
Renewable
Disc
-
Cover Hinge Hinge Pin
Bolted
Cover Gasket
Spiral Wound
Forged / Bar
B
80
Description
Cast
Rev
50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 2" -16" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Manufacturer's Alternate/ Acceptance
13% Cr. Steel/ ASTM A 216 WCB + 13% Cr. Steel Deposit ASTM A 216 Gr WCB ASTM A 216 Gr WCB 13% Cr. Steel SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 101 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53311P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
C15B
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 150# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Size Range Rating Ends
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
450 325
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body Seat Ring Spring Piston Cover Hinge Pin / Guide
Forged Renewable / Integral Bolted Forged / Bar
Cover gasket
Spiral Wound
ASTM A105N UNS S32750/ 32760 Inconel X-750 UNS S32750/ 32760 ASTM 105N UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 102 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53311
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 C15B
Piping Class Manuf. Standard Testing Standard
Services / Fluids
B
Valve Type
BS 1868 (2" - 24") API 6D (26" -48") API 598/ BS 6755 Part-1 Hydrocarbon Gas/ Oil/ Condensate, Glycol
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
ASME B 16.34 450 325
Size Range Rating Ends
B
B
Flanged, 150#, ASME B16.5 / B 16.47 Series A, RF, Finish 125 AARH
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 48" 150# Special Requirements
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body
Cast
ASTM A 216 Gr WCB
Seat Ring
Renewable
UNS S 32750 / 32760
Disc Cover Hinge Hinge Pin / Guide
Bolted
Cover gasket
Spiral Wound
UNS S 32750 / 32760 ASTM A 216 Gr WCB ASTM A 216 Gr WCB UNS S 32750 / 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Forged / Bars
Contractor Document Number
Manufacturer's Alternate/ Acceptance
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 103 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53312P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
C15B
Size Range Rating Ends
Hydrocarbon Oil/ Condensate
Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10 Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 150# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
450 325
Contractor Document Number
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.
80
Description
Type of Construction
Material of Construction
Body Seat Ring Spring Piston Cover Hinge Pin / Guide
Forged Renewable/ Integral Bolted Forged / Bar
Cover gasket
Spiral Wound
ASTM A105N SS316L Inconel X-750 SS316L ASTM 105N SS316L SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 104 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53312
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 C15B
Piping Class Manuf. Standard Testing Standard
Services / Fluids
B
Valve Type
BS 1868 (2" - 24") API 6D (26" -48") API 598/ BS 6755 Part-1 Hydrocarbon Oil/ Condensate
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
ASME B 16.34 450 325
B
Size Range Rating Ends
B
Flanged, 150#, ASME B16.5/ B 16.47 Series A, RF, Finish 125 AARH
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 48" 150# Special Requirements
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.
Face to Face dimension ASME B 16.10 80
Air Test psi (g)
Description
Type of Construction
Material of Construction
Body
Cast
ASTM A 216 Gr WCB
Seat Ring
Renewable
SS316L
Disc Cover Hinge Hinge Pin / Guide
Bolted
Cover gasket
Spiral Wound
SS316L ASTM A 216 Gr WCB ASTM A 216 Gr WCB SS316L SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Forged / Bars
Contractor Document Number
Manufacturer's Alternate/ Acceptance
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 105 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53361
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S10A BS 1868
Testing Standard
API 598/ BS 6755 Part-1
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution
Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
425 325
Size Range Rating Ends
Air Test psi (g)
B
80
Description
Type of Construction
Material of Construction
Body Seat Ring Disc Cover Hinge Hinge Pin
Cast Renewable Bolted
Cover gasket
Spiral Wound
ASTM A 351 Gr CF8M SS 316 SS 316 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Forged / Bar
Rev
50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 2" - 12" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Manufacturer's Alternate/ Acceptance
B
Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 106 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53363P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
S10B API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 150# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be
complied. Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Hydrocarbon Gas/ Condensate ,Glycol
Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
425 325
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body Piston Seat Ring Spring Cover Guide
Forged Lift Type Renewable / Integral Bolted Forged / Bar
Cover gasket
Spiral Wound
ASTM A 182 F 316/ 316L Dual Stamped UNS S 32750/ 32760 UNS S 32750/ 32760 Inconel X-750 ASTM A 182 F 316/ 316L Dual Stamped UNS S 32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts Corrosion Resistant Name Plate B General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 107 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53363
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S10B
Manuf. Standard
BS 1868
Testing Standard
API 598/ BS 6755 Part-1
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 12" 150# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be
complied. Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Hydrocarbon Gas/ Condensate ,Glycol
Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
425 325
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body Seat Ring Disc Cover Hinge Hinge Pin
Cast Renewable Bolted
Cover gasket
Spiral Wound
ASTM A 351 Gr CF8M UNS S 32750/ 32760 UNS S 32750/ 32760 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M UNS S 32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Forged / Bar
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts B Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 108 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53364P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
S10B API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 150# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be
complied. Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Hydrocarbon Gas/ Condensate ,Glycol
Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
425 325
Air Test psi (g)
2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.
80
Description
Type of Construction
Material of Construction
Body Piston Seat Ring Spring Cover Guide
Forged Lift Type Renewable / Integral Bolted Forged / Bar
Cover gasket
Spiral Wound
ASTM A 182 F 316/ 316L Dual Stamped 316/ 316L Dual Stamped 316/ 316L Dual Stamped Inconel X-750 ASTM A 182 F 316/ 316L Dual Stamped 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts B Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 109 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53364
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S10B
Manuf. Standard
BS 1868
Testing Standard
API 598/ BS 6755 Part-1
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 12" 150# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be
complied. Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Hydrocarbon Gas/ Condensate ,Glycol
Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
425 325
Air Test psi (g)
2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.
80
Description
Type of Construction
Material of Construction
Body Seat Ring Disc Cover Hinge Hinge Pin
Cast Renewable Bolted
Cover gasket
Spiral Wound
ASTM A 351 Gr CF8M SS 316L SS 316L ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Forged / Bar
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts B Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 110 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q15A
Manuf. Standard
API 594
Testing Standard
API 598
Services / Fluids
Brackish Water
SHEET NO. 53378D Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve Type
CHECK VALVE Dual plate check
Size Range Rating Ends
3" - 24" 150# Special Requirements
Wafer Lug, 150 #, ASME B16.5, RF, Finish - 125 AARH
1. Straight length or any specific installation requirement shall be clearly specified by the vendor.
Pressure -Temperature Face to Face dimension ASME B 16.24 API 594 Rating Hydro Test Pressure 300 80 Body psi (g) Air Test psi (g) 225 Seat psi (g) Description Type of Construction Material of Construction Manufacturer's Alternate/ Acceptance Cast ASTM B 148-UNS C95800 Body Spring Loaded Plates (Discs) Monel / NI-AL-Bronze Body Seat RPTFE Plate Seat RPTFE Forged / Bar Hinge Pin Monel / NI-AL-Bronze Forged / Bar Stop Pin Monel / NI-AL-Bronze Inconel X-750 Spring Seal Welded (Note 6) ASTM B 148-UNS C95800 Retainers Plate Support Sleeve Monel / NI-AL-Bronze Monel / NI-AL-Bronze Other Wetted Parts Washer Bearings Monel / NI-AL-Bronze Silica Gel Retainer Packing Name Plate Corrosion Resistant SS / Ni Alloy General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Retainerless Design is also acceptable. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 8. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 9. Care should be taken to avoid galvanic corrosion by dissimlar metals.
Page 111 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53378DF
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13B ( 4"- 12"), F10A (2"-24")
Size Range Rating Ends
2"-24" 150# Special Requirements
Testing Standard
API 598
Services / Fluids
Potable Water / Fresh Water, Plant Air, Brackish Water
Wafer Lug, 150 #, ASME B16.5, FF, Finish - 125 AARH
ASME B 16.24
Face to Face dimension API 594
Description
Type of Construction
B
CHECK VALVE Dual plate check
API 594
300 225
Rev
50489-530-051-SPC-1002
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Air Test psi (g)
1. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast ASTM B 148-UNS C95800 Body Spring Loaded Plates (Discs) Monel / NI-AL-Bronze (Note 10) Body Seat RPTFE Plate Seat RPTFE Forged / Bar Hinge Pin Monel / NI-AL-Bronze (Note 10) Forged / Bar Stop Pin Monel / NI-AL-Bronze (Note 10) Inconel X-750 Spring Seal Welded (Note 6) ASTM B 148-UNS C95800 Retainers Monel / NI-AL-Bronze (Note 10) Plate Support Sleeve B Monel / NI-AL-Bronze (Note 10) Other Wetted Parts Washer Bearings Monel / NI-AL-Bronze (Note 10) Silica Gel Retainer Packing Corrosion Resistant SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Retainerless Design is also acceptable. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 8. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 9. Care should be taken to avoid galvanic corrosion by dissimlar metals. 10. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .
B
Page 112 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53379P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q15B, F10B API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 150# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Effluent Water,Oily Water, Hydrocarbon Oil/ Condensate
Flanged, 150 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
450 325
Contractor Document Number
Air Test psi (g)
80
Type of Construction
Material of Construction
Forged Lift Type Renewable / Integral Bolted Forged / Bar Flat Ring Corrosion Resistant
ASTM A 182 Gr F 53 UNS S32750/ 32760 UNS S32750/ 32760 Inconel X-750 ASTM A 182 Gr F 53 UNS S32750/ 32760 Compressed Non Asbestos Fibre ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Body Piston Seat Ring Spring Cover Guide Cover gasket B Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 113 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q15B
Manuf. Standard
API 594
Testing Standard
API 598
Services / Fluids
Hydrocarbon Oil/ Condensate, Oily Water
SHEET NO. 53379D Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve Type
CHECK VALVE Dual plate check
Size Range Rating Ends
2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
ASME B 16.34 450 325 Type of Construction
Wafer Lug, 150 #, FF, ASME B16.5 (2"-24") 2. Straight length or any specific installation requirement shall be clearly FLGD, 150#, FF, ASME B16.47 'A' (26"-48"), specified by the vendor. Finish - 125 AARH Face to Face dimension API 594 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 114 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
SHEET NO. 53379DF Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve Type
CHECK VALVE Dual plate check
API 598
Size Range Rating Ends
2" - 36" 150# Special Requirements
Effluent Water, Oily Water
Wafer Lug, 150 #, FF, ASME B16.5 (2"-24") FLGD, 150#, FF, ASME B16.47 'A' (26"-48"), Finish - 125 AARH
ASME B 16.34
Face to Face dimension API 594
F10B API 594
450 325 Type of Construction
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification.. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 115 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F10A (1/2" - 1 1/2"), Q15A (1/2" - 2") MSS-SP-80
Testing Standard
BS 5154 / MSS-SP-80
Services / Fluids
Brackish Water
Flanged, 150#, ASME B 16.5 ,FF, Finish 125 AARH
ASME B 16.24
Face to Face dimension Manufacturer's Standard.
Description
350 250
Size Range Rating Ends
Air Test psi (g)
53380P Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Screwed Cover Spring Loaded Piston 1/2" - 2" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
80
Type of Construction
Material of Construction
Cast Renewable / Integral Lift Type Bolted Nickel or Copper alloy (Note 4) Corrosion Resistant
ASTM B62 C83600 ASTM B62 C83600 Inconel X-750 ASTM B62 C83600 ASTM B62 C83600 To Manufacturer's Standard. ASTM A 193 Gr B7 SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Body Seat Ring Spring Piston Cover Guide Cover gasket ASTM A 194 Gr 2H Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 6. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 7. Care should be taken to avoid galvanic corrosion by dissimlar metals.
Page 116 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13B MSS-SP-80
Testing Standard
BS 5154 / MSS-SP-80
Services / Fluids
Potable/ Fresh Water, Plant Air
SCRF, 3000# to NPT (F), ASME B 1.20.1
ASME B 16.24
Face to Face dimension Manufacturer's Standard.
Description
350 250
Size Range Rating Ends
Air Test psi (g)
53380S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Screwed Cover Spring Loaded Piston 1/2" - 3" 150# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
80
Type of Construction
Material of Construction
Cast Renewable / Integral Lift Type Screwd Nickel or Copper alloy (Note 4) Corrosion Resistant
ASTM B62 C83600 ASTM B62 C83600 Inconel X-750 ASTM B62 C83600 ASTM B62 C83600 To Manufacturer's Standard. ASTM A 193 Gr B7 SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Body Seat Ring Spring Piston Cover Guide Cover gasket ASTM A 194 Gr 2H Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 6. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 7. Care should be taken to avoid galvanic corrosion by dissimlar metals.
Page 117 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53399P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
N10B, N10C API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Valve Type B
Size Range Rating Ends
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 2" 150# Special Requirements
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Off Spec Crude Oil
Flanged, 150 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
450 325
Air Test psi (g)
80
Type of Construction
Material of Construction
Forged Lift Type Renewable / Integral Bolted Forged / Bar Flat Ring Corrosion Resistant
ASTM B564-UNS N06625 INCONEL 625 INCONEL 625 Inconel X-750 ASTM B564-UNS N06625 INCONEL 625 Compressed Non Asbestos Fibre ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Body Piston Seat Ring Spring Cover Guide Cover gasket Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 118 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53399D
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
B
N10B (3" - 20") N10C (3" - 6")
Manuf. Standard
API 594
Testing Standard
API 598
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
B
Size Range Rating Ends
Off Spec Crude Oil
ASME B 16.34
Face to Face dimension API 594
Type of Construction
Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Dual plate check
Valve Type
Wafer Lug, 150 #, ASME B16.5, RF, Finish - 125 AARH
450 325
Contractor Document Number
3" - 20" 150# Special Requirements
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM B564-UNS N06625 Plates (Discs) INCONEL 625 Body Seat RPTFE Plate Seat RPTFE Hinge Pin INCONEL 625 Stop Pin INCONEL 625 Inconel X-750 Spring Retainers ASTM B564-UNS N06625 Plate Support Sleeve INCONEL 625 INCONEL 625 Other Wetted Parts Washer Bearings INCONEL 625 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 119 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53411P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
C35B
Size Range Rating Ends
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 300 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10 Air Test psi (g)
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 300# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
1125 825
Contractor Document Number
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
80
Description
Type of Construction
Material of Construction
Body Seat Ring Spring Piston Cover Hinge Pin / Guide
Forged Renewable / Integral Bolted Forged / Bar
Cover gasket
Spiral Wound
ASTM A105N UNS S32750/ 32760 Inconel X-750 UNS S32750/ 32760 ASTM 105N UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 120 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53411
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 C35B
Piping Class
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 16" 300# Special Requirements
Valve Type
Manuf. Standard
BS 1868
Testing Standard
API 598/ BS 6755 Pt.1
Size Range Rating Ends
Services / Fluids
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 300 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
1125 825
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body
Cast
ASTM A 216 Gr WCB
Seat Ring
Renewable
UNS S32750/ 32760
Disc Cover Hinge Hinge Pin / Guide
Bolted
Cover gasket
Spiral Wound
UNS S32750/ 32760 ASTM A 216 Gr WCB ASTM A 216 Gr WCB UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Forged / Bars
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts (Note 5) Name Plate Corrosion Resistant General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 121 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53461
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S30A BS 1868 API 598/ BS 6755 Part-1 Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor ASME B 16.34 1100 800
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 12" 300# Special Requirements
Valve Type Size Range Rating Ends Flanged, 300 #, ASME B16.5, RF, Finish - 125 AARH Face to Face dimension ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body Seat Ring Disc Cover Hinge Hinge Pin
Cast Renewable Bolted
Cover gasket
Spiral Wound
ASTM A 351 Gr CF8M SS316 SS 316 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Forged / Bar
Contractor Document Number
Manufacturer's Alternate/ Acceptance
B
Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 122 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53478
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q35A BS 1868
Testing Standard
API 598/ BS 6755 Part-1
Services / Fluids
Brackish Water
Flanged, 300 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
775 575
Size Range Rating Ends
Air Test psi (g)
B
80
Description
Type of Construction
Material of Construction
Body Seat Ring Disc Cover Hinge Hinge Pin
Cast Renewable Bolted
Cover gasket
Spiral Wound
ASTM B 148-UNS C95800 Monel / NI-AL-Bronze Monel / NI-AL-Bronze ASTM B 148-UNS C95800 ASTM B 148-UNS C95800 Monel / NI-AL-Bronze SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Forged / Bar
Rev
50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 3" - 24" 300# Special Requirements
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
Contractor Document Number
Manufacturer's Alternate/ Acceptance
Note 7 Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 6. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 7. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 123 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q35A
Manuf. Standard
API 594
Testing Standard
API 598
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Dual plate check
Size Range Rating Ends
3" - 32" 300# Special Requirements
Brackish Water
ASME B 16.24
Face to Face dimension API 594 Air Test psi (g)
Type of Construction
53478D
Valve Type
Wafer Lug, 150 #, FF, ASME B16.5 (2"-24") FLGD, 150#, FF, ASME B16.47 'A' (26"-48"), Finish - 125 AARH
775 575
SHEET NO.
1. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast ASTM B 148-UNS C95800 Body Spring Loaded Plates (Discs) Monel / NI-AL-Bronze Body Seat RPTFE Plate Seat RPTFE Forged / Bar Hinge Pin Monel / NI-AL-Bronze Forged / Bar Stop Pin Monel / NI-AL-Bronze Inconel X-750 Spring Seal Welded (Note 6) ASTM B 148-UNS C95800 Retainers Plate Support Sleeve Monel / NI-AL-Bronze Monel / NI-AL-Bronze Other Wetted Parts Washer Bearings Monel / NI-AL-Bronze Silica Gel Retainer Packing Corrosion Resistant SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Retainerless Design is also acceptable. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 8. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 9. Care should be taken to avoid galvanic corrosion by dissimlar metals.
Page 124 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53479P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q35B, F30B
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 300# Special Requirements
Valve Type
Manuf. Standard
API 602/ BS EN ISO 15761
Testing Standard
API 598/ BS 6755 Pt. 1
Services / Fluids
Hydrocarbon Oil/ Condensate, Oily Water
Flanged, 300 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
1125 825
Air Test psi (g)
80
Type of Construction
Material of Construction
Forged Lift Type Renewable / Integral Bolted Forged / Bar Flat Ring Corrosion Resistant
ASTM A 182 Gr F 53 UNS S32750/ 32760 UNS S32750/ 32760 Inconel X-750 ASTM A 182 Gr F 53 UNS S32750/ 32760 Compressed Non Asbestos Fibre ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Body Piston Seat Ring Spring Cover Hinge Pin Cover gasket B Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 125 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q35B
Testing Standard
Size Range Rating Ends
Services / Fluids
Hydrocarbon Oil/ Condensate, Oily Water
Wafer Lug, 300 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension API 594
Type of Construction
Rev
50489-530-051-SPC-1002
B
2" - 24" 300# Special Requirements
API 598/ BS 6755 Pt. 1
Description
Contractor Document Number
CHECK VALVE Dual plate check
API 594
1125 825
53479D
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 126 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q35A
Manuf. Standard
API 594
Testing Standard
API 598
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Dual plate check
Size Range Rating Ends
2" 300# Special Requirements
Brackish Water
ASME B 16.34
Face to Face dimension API 594
Type of Construction
53482D
Valve Type
Wafer Lug, 300 #, ASME B16.5, RF, Finish - 125 AARH
1125 825
SHEET NO.
Air Test psi (g)
1. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 127 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
N30C
Manuf. Standard
API 594
Testing Standard
API 598
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Dual plate check
Size Range Rating Ends
8" - 16" 300# Special Requirements
Off Spec Crude Oil
ASME B 16.34
Face to Face dimension API 594
Type of Construction
53498D
Valve Type
Wafer Lug, 300 #, ASME B16.5, RF, Finish - 125 AARH
1125 825
SHEET NO.
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 216 Gr WCB + 3 MM Inconel 625 Plates (Discs) INCONEL 625 Body Seat RPTFE Plate Seat RPTFE Hinge Pin INCONEL 625 Stop Pin INCONEL 625 Inconel X-750 Spring Retainers ASTM A 216 Gr WCB + 3 MM Inconel 625 Plate Support Sleeve INCONEL 625 INCONEL 625 Other Wetted Parts Washer Bearings INCONEL 625 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 128 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53499P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
N30B, N30C API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 2" B 300# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Off Spec Crude Oil
Flanged, 300 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1125 825
Air Test psi (g)
80
Type of Construction
Material of Construction
Forged Lift Type Renewable / Integral Bolted Forged / Bar Flat Ring Corrosion Resistant
ASTM B564-UNS N06625 INCONEL 625 INCONEL 625 Inconel X-750 ASTM B564-UNS N06625 INCONEL 625 Compressed Non Asbestos Fibre ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Body Piston Seat Ring Spring Cover Guide Cover gasket Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 129 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 N30B (3" - 16") N30C (3" - 6")
Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
B
API 594 API 598
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Dual plate check
Size Range Rating Ends
3" - 16" 300# Special Requirements
Off Spec Crude Oil
ASME B 16.34
Face to Face dimension API 594
Type of Construction
53499D
Valve Type
Wafer Lug, 300 #, ASME B16.5, RF, Finish - 125 AARH
1125 825
SHEET NO.
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM B564-UNS N06625 Plates (Discs) INCONEL 625 Body Seat RPTFE Plate Seat RPTFE Hinge Pin INCONEL 625 Stop Pin INCONEL 625 Inconel X-750 Spring Retainers ASTM B564-UNS N06625 Plate Support Sleeve INCONEL 625 INCONEL 625 Other Wetted Parts Washer Bearings INCONEL 625 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 130 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53511P
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
C65B
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 600# Special Requirements
Valve Type
API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
Size Range Rating Ends
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 600 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
2225 1650
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body Seat Ring Spring Piston Cover Hinge Pin / Guide
Forged Renewable/ Integral Bolted Forged / Bar
Cover gasket
Spiral Wound
ASTM A105N UNS S32750/ 32760 Inconel X-750 UNS S32750/ 32760 ASTM 105N UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Manufacturer's Alternate/ Acceptance
Cover Bolts / Nuts (Note 5) Name Plate Corrosion Resistant General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 131 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53511
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 C65B
Piping Class
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 24" 600# Special Requirements
Valve Type
Manuf. Standard
BS 1868
Testing Standard
API 598/ BS 6755 Pt. 1
Size Range Rating Ends
Services / Fluids
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 600 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension ASME B 16.10
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
2225 1650
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body
Cast
ASTM A 216 Gr WCB
Seat Ring
Renewable
UNS S32750/ 32760
Disc
-
UNS S32750/ 32760
Cover Hinge Hinge Pin / Guide
Bolted
Cover gasket
Spiral Wound
ASTM A 216 Gr WCB ASTM A 216 Gr WCB UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy
Forged / Bars
Manufacturer's Alternate/ Acceptance
(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 132 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C65B
B
2" - 24" 600# Special Requirements
Testing Standard
Services / Fluids
Hydrocarbon Gas / Oil / Condensate, Glycol
Wafer Lug, 600 #, ASME B16.5, RF, Finish - 125 AARH
ASME B 16.34
Face to Face dimension API 594
Type of Construction
Rev
50489-530-051-SPC-1002
Size Range Rating Ends
API 598
Description
Contractor Document Number
CHECK VALVE Dual plate check
API 594
2225 1650
53511D
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 216 Gr WCB UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 216 Gr WCB UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 133 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
53561
KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
S60A BS 1868 API 598/ BS 6755 Part-1 Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor ASME B 16.34 2225 1650
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Swing check Bolted cover 2" - 12" 600# Special Requirements
Valve Type Size Range Rating Ends Flanged, 600 #, ASME B16.5, RF, Finish - 125 AARH Face to Face dimension ASME B 16.10 Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body Seat Ring Disc Cover Hinge Hinge Pin
Cast Renewable Bolted
Cover gasket
Spiral Wound
ASTM A 351 Gr CF8M SS316 SS 316 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy
Forged / Bar
Contractor Document Number
Manufacturer's Alternate/ Acceptance
B Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 134 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q95B API 594
Testing Standard
API 598
Services / Fluids
Effluent Water
Wafer Lug, 900 #, ASME B16.5, RTJ, Finish - 32 AARH
ASME B 16.34
Face to Face dimension API 594
Description
3375 2475 Type of Construction
Size Range Rating Ends
Air Test psi (g)
53679D Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Dual plate check
Valve Type
Manuf. Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
3" - 20" 900# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 995 Gr 5A/ 6A Plates (Discs) UNS S 32750 / 32760 Body Seat RPTFE Plate Seat RPTFE Hinge Pin UNS S 32750 / 32760 Stop Pin UNS S 32750 / 32760 Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A Plate Support Sleeve UNS S 32750 / 32760 UNS S 32750 / 32760 Other Wetted Parts Washer Bearings UNS S 32750 / 32760 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 135 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Q95B API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1
SHEET NO. 53779P Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 1500# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Effluent Water
ASME B 16.34 5625 4125 Type of Construction
Flanged, 1500#, ASME B16.5, RTJ, Finish 32 complied. AARH Face to Face dimension ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Renewable/ Integral Bolted Forged / Bars Ring Type
Body ASTM A182 Gr F 53 Seat Ring UNS S 32750 / 32760 Spring Inconel X-750 Piston UNS S 32750 / 32760 Cover ASTM A182 Gr F 53 UNS S 32750 / 32760 Hinge Pin / Guide Cover gasket Super Duplex Oval Shape Gasket ASTM A 193 Gr B8M ASTM A 194 Gr 8M Cover Bolts / Nuts B Corrosion Resistant SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.
Page 136 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
Q95B
Manuf. Standard
API 594
Testing Standard
API 598
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
CHECK VALVE Dual plate check
Size Range Rating Ends
2" 1500# Special Requirements
Effluent Water
ASME B 16.34
Face to Face dimension API 594
Type of Construction
53779D
Valve Type
Wafer Lug, 1500 #, ASME B16.5, RTJ, Finish - 32 AARH
5625 4125
SHEET NO.
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant
Body ASTM A 995 Gr 5A/ 6A Plates (Discs) UNS S 32750 / 32760 Body Seat RPTFE Plate Seat RPTFE Hinge Pin UNS S 32750 / 32760 Stop Pin UNS S 32750 / 32760 Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A Plate Support Sleeve UNS S 32750 / 32760 UNS S 32750 / 32760 Other Wetted Parts Washer Bearings UNS S 32750 / 32760 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.
Page 137 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13A
Valve Type
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Fuel Oil (Diesel), Inert Gas
SW, 3000 # to ASME B 16.11, (Note 9)
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
2975 2175 Type of Construction
Size Range Rating Ends
Air Test psi (g)
SHEET NO. 54001 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged ASTM A105 Body / Body Cover Solid Ball SS 316L (Note 10) Anti Blow Out (No Casting) Stem SS 316L Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr Steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 15) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 15) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 15) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at each end of valve prior to valve assembly. Refer Annexure III for nipple details. Page 138 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54001 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 15. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B633.
Page 139 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13A
Valve Type
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Fuel Oil (Diesel), Inert Gas
SCRM X SCRF, NPT, 3000#, ASME B 1.20.1, (Note 9)
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
2975 2175 Type of Construction
Size Range Rating Ends
Air Test psi (g)
SHEET NO. 54001S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged ASTM A105 Body / Body Cover Solid (Note 10) Ball SS 316L Anti Blow Out (No Casting) Stem SS 316L Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr Steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 15) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 15) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 15) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with screwed NPT (F) X NPT (M) end, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Open end of nipple shall be NPT (M). Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 140 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54001S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 15. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 141 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13A
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Fuel Oil (Diesel), Inert Gas
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
ASME B 16.34 2975 2175 Type of Construction
Valve Type Size Range Rating Ends SW X SCRF (NPT), 3000# to ASME B 16.11, (Note 9)
SHEET NO. 54001X Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 3/4" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Face to Face dimension Manufacturer's Std. Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A105 Forged Body / Body Cover Solid (Note 10) Ball SS 316L Anti Blow Out (No Casting) Stem SS 316L Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr Steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 15) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A194 Gr 2H (Note 15) ASTM A193 Gr B7 Body Stud / Nuts (Note 15) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with SW X SCRD (F) ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 142 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54001X Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 15. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 143 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 S10A, S30A, S60A
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution
SW, 3000 # to ASME B 16.11, (Note 9)
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Description
2900 2125 Type of Construction
Valve Type Size Range Rating Ends
Air Test psi (g)
54061 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Piping Class
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A182 Gr F316/ 316L Dual Stamped Solid (Note 10) SS 316/ 316L Dual Stamped Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 144 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54061 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valveat 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded each end of valve prior to valve assembly. Refer Annexure III for nipple details. 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 145 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 S10A, S30A, S60A
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution
SCRM X SCRF, NPT, 3000#, ASME B 1.20.1, (Note 9)
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Description
2900 2125 Type of Construction
Valve Type Size Range Rating Ends
Air Test psi (g)
54061S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Piping Class
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A182 Gr F316/ 316L Dual Stamped Solid (Note 10) SS 316/ 316L Dual Stamped Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 146 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54061S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball(150mm Valve long) welded at one end of valve 9. For Soft Seated Ball Valves with screwed NPT (F) X NPT (M) end, manufacturer/ vendor shall supply those valves complete with pipe nipples prior to valve assembly. Open end of nipple shall be NPT (M). Refer Annexure III for nipple details. Other end of valve shall be NPT (F). 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 147 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
S10A, S30A, S60A
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
ASME B 16.34 2900 2125 Type of Construction
Valve Type Size Range Rating Ends
SW X SCRF (NPT), 3000# to ASME B 16.11, (Note 9)
SHEET NO. 54061X Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 3/4" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Face to Face dimension Manufacturer's Std. Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A182 Gr F316/ 316L Dual Stamped Solid (Note 10) SS 316/ 316L Dual Stamped Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts B Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 148 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54061X Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve 9. For Soft Seated Ball Valves with SW X SCRD (F) ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mmBall long) welded at one end of valve prior to valve assembly. Refer Annexure III for nipple details. Other end of valve shall be NPT (F). 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 149 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F30A, Q35A
Valve Type
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Brackish Water
SW, 3000 # to ASME B 16.11, (Note 9)
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
3000 2200 Type of Construction
Size Range Rating Ends
Air Test psi (g)
SHEET NO. 54082 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at each end of valve prior to valve assembly. Refer Annexure III for nipple details. Page 150 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54082 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 151 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F30A
Valve Type
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Brackish Water
SW, 3000 # to ASME B 16.11, (Note 9)
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
3000 2200 Type of Construction
Size Range Rating Ends
Air Test psi (g)
SHEET NO. 54082Y Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side. 2. Ball Valve shall be spring loaded
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever B ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at each end of valve prior to valve assembly. Refer Annexure III for nipple details. Page 152 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54082Y Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 153 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F30A, Q35A
Valve Type
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Brackish Water
SCRM X SCRF, NPT, 3000#, ASME B 1.20.1, (Note 9)
ASME B 16.34
Face to Face dimension Manufacturer's Std.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
3000 2200 Type of Construction
Size Range Rating Ends
Air Test psi (g)
SHEET NO. 54082S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with screwed NPT (F) X NPT (M) end, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Open end of nipple shall be NPT (M). Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 154 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54082S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 155 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
F30A, Q35A
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Brackish Water
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
ASME B 16.34 3000 2200 Type of Construction
Valve Type Size Range Rating Ends SW X SCRF (NPT), 3000# to ASME B 16.11, (Note 9)
SHEET NO. 54082X Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 3/4" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Face to Face dimension Manufacturer's Std. Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with SW X SCRD (F) ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 156 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54082X Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 157 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
C13A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Fuel Oil (Diesel), Inert Gas ASME B 16.34 450 325 Type of Construction
SHEET NO. 54301 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 2" - 16" Rating 150# Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, RF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast ASTM A216 Gr WCB) Body / Body Cover Solid (Note 9) Ball SS 316L (Note 15) Anti Blow Out (No Casting) SS 316L Stem Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded.
Page 158 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54301 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 14" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm ENP Coating.
Page 159 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
54311 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO.
C15B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Flanged, 150#, ASME B16.5/ B 16.47 Series A, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D/ ASME B16.10
450 325
Description
Type of Construction
Body / Body Cover
Forged / Cast
Air Test psi (g)
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 36") UNS S32750 / S32760 (Note 15) UNS S32750 / S32760 ASTM A105N / UNS S32750 / S32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750
Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal (Note 14) Gland Retaining Nut Forged / Machined Wrench / Lever (Note 14) Body Stud / Nuts (Note 14) Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 160 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
SHEET NO. 54311 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 16" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.
Ball Valve
Page 161 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
54312 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO.
C15B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Hydrocarbon Gas/ Condensate
Flanged, 150#, ASME B16.5/ B 16.47 Series A, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D/ ASME B16.10
450 325
Description
Type of Construction
Body / Body Cover
Forged / Cast
Air Test psi (g)
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side. 3. This valve data sheet is applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) Services only.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 36") SS 316L (Note 15) SS 316L ASTM A105N/ SS 316L RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750
Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal (Note 14) Gland Retaining Nut Forged / Machined Wrench / Lever (Note 14) Body Stud / Nuts (Note 14) Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 162 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 16" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm SS 316L Overlay.
SHEET NO. 54312 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 163 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
S10A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Flanged, 150#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D
Type of Construction
Air Test psi (g)
54361 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 2" - 12" 150# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution
425 325
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast ASTM A 351 Gr CF8M Body / Body Cover Solid (Note 9) SS 316 Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 164 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54361 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve mounted. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shallBall be trunnion 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 165 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description Body / Body Cover
S10B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Condensate, Glycol ASME B 16.34 425 325
SHEET NO. 54363 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 12" Size Range 150# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 150#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body Bonnet cavity pressure to the upstream side. Face to Face dimension API 6D/ ASME B16.10 Air Test psi (g)
80
Type of Construction
Material of Construction
Forged / Cast
ASTM A 182 Gr F 316/ 316L Dual Stamped (1/2" - 1 1/2")/ ASTM A 351 Gr CF8M (2" - 12")
Manufacturer's Alternate/ Acceptance
Solid (Note 9) UNS S32750/ S32760 Ball Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 166 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54363 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 167 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description Body / Body Cover
S10B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Condensate ASME B 16.34 425 325
SHEET NO. 54364 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 12" Size Range 150# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 150#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body Bonnet cavity pressure to the upstream side. 3. This valve data sheet is applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) Services only. Face to Face dimension API 6D/ ASME B16.10 Air Test psi (g)
80
Type of Construction
Material of Construction
Forged / Cast
ASTM A 182 Gr F 316/ 316L Dual Stamped (1/2" - 1 1/2")/ ASTM A 351 Gr CF8M (2" - 12")
Manufacturer's Alternate/ Acceptance
Solid (Note 9) SS 316L Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts B Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 168 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54364 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 169 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q15A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water
ASME B 16.24 300 225 Type of Construction
SHEET NO. 54378 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry 3" - 24" Size Range 150# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, RF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM B 148 UNS C95800 Solid (Note 9) Ball Monel / NI-AL-Bronze Anti Blow Out (No Casting) Stem Monel / NI-AL-Bronze Bolted / Retained by Nuts & Washer Gland Monel / NI-AL-Bronze Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 170 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54378 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 171 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
C13B (2"-12") F10A (2"-24") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water, Potable/ Fresh Water, Plant Air ASME B 16.24 300 225 Type of Construction
SHEET NO. 54378F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 2" - 24" Rating 150# Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side. Flanged, 150#, ASME B16.5, FF, Finish 125 AARH Face to Face dimension API 6D Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM B 148 UNS C95800 Solid (Note 9) Ball Monel / NI-AL-Bronze (Note 17) Anti Blow Out (No Casting) Stem Monel / NI-AL-Bronze (Note 17) B Bolted / Retained by Nuts & Washer Gland Monel / NI-AL-Bronze (Note 17) Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material. 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 172 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54378F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
C13BLock-Open (2"-12") (LO)/ Lock-Closed (LC) provision. 11. All Ball-Valves shall be provided with 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Ball Valve
14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 17. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .
B
Page 173 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
54379 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO.
C15B (0.5"-2") F10B (0.5"-1.5") Q15B (0.5"-36") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Size Range Rating Ends
Hydrocarbon Gas/ Oil/ Condensate, Glycol, Oily Water, Effluent Water
Flanged, 150#, ASME B 16.5/ B 16.47 Series A, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D/ ASME B 16.10
450 325
Description
Type of Construction
Body / Body Cover
Forged / Cast
Ball Valve Valve Type
Air Test psi (g)
FULL BORE Split Body, Side Entry 1/2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A 182 Gr F 53 (1/2" - 3")/ ASTM A 995 Gr 5A/ 6A (4" - 36") (Note 14) UNS S32750/ 32760 (Note 14) UNS S32750/ 32760 UNS S32750/ 32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B8M ASTM A194 Gr 8M ASTM A193 Gr B8M SS/ Ni Alloy Inconel X-750
Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal Gland Retaining Nut Forged / Machined Wrench / Lever Body Stud / Nuts B Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. Page 174 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54379 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. Ball valves in the size range of 16" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.
Page 175 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
F10B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water, Oily Water
ASME B 16.34 450 325 Type of Construction
Valve Type Size Range Rating Ends Flanged, 150#, ASME B 16.5/ B 16.47 Series A, RF, Finish 125 AARH
SHEET NO. 54379F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.
API 6D Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM A 995 Gr 5A/ 6A (Note 14) Solid (Note 9) Ball UNS S32750/ 32760 (Note 14) Anti Blow Out (No Casting) Stem UNS S32750/ 32760 Bolted / Retained by Nuts & Washer Gland UNS S32750/ 32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 176 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54379F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. Ball valves in the size range of 16" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.
Page 177 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
F10A (0.5"-1.5") Q15A (0.5"-2") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water
ASME B 16.24 350 250 Type of Construction
SHEET NO. 54380F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 2" Size Range 150# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, FF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Body / Body Cover Cast ASTM B62 UNS C83600 Ball Solid (Note 9) Bronze/ Monel Stem Anti Blow Out (No Casting) Bronze/ Monel Gland Bolted / Retained by Nuts & Washer Bronze/ Monel Body Seat Soft Seat (Note 7) RPTFE Body Seals Soft Seal RPTFE/ PTFE/ Graphoil Stem Seal Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Gland Retaining Nut (Note 16) ASTM A194 Gr 2H Wrench / Lever Forged / Machined Carbon Steel / Malleable Iron Body Stud / Nuts (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Gland Bolts (Note 16) ASTM A193 Gr B7 Name Plate Corrosion Resistant SS/ Ni Alloy Spring Inconel X-750 General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. Page 178 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54380F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve 14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 179 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
F10A (0.5"-1.5") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water
ASME B 16.24 350 250 Type of Construction
SHEET NO. 54380YF Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 1 1/2" Size Range 150# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, FF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. 2. Ball Valve shall be spring loaded AARH Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Body / Body Cover Cast ASTM B62 UNS C83600 Ball Solid (Note 9) Bronze/ Monel Stem Anti Blow Out (No Casting) Bronze/ Monel Gland Bolted / Retained by Nuts & Washer Bronze/ Monel Body Seat Soft Seat (Note 7) RPTFE Body Seals Soft Seal RPTFE/ PTFE/ Graphoil Stem Seal Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Gland Retaining Nut (Note 16) ASTM A194 Gr 2H Wrench / Lever Forged / Machined Carbon Steel / Malleable Iron Body Stud / Nuts (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Gland Bolts (Note 16) ASTM A193 Gr B7 Name Plate Corrosion Resistant SS/ Ni Alloy Spring Inconel X-750 General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. Page 180 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54380YF Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve 14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 181 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class
C13B
Valve Type
Manuf. Standard
BS EN ISO 17292
Testing Standard
BS EN ISO 17292
Services / Fluids
Potable/ Fresh Water, Plant Air
SCRF, 150# to NPT(F), ASME B 1.20.1
ASME B 16.24
Face to Face dimension Manufacturer's Std.
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
350 250 Type of Construction
Size Range Rating Ends
Air Test psi (g)
SHEET NO. 54380S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" -11/2" 150# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast ASTM B62 UNS C83600 Body / Body Cover Solid (Note 9) ASTM B62 UNS C83600 Ball Anti Blow Out (No Casting) Ni Al Bronze Stem Bolted / Retained by Nuts & Washer Ni Al Bronze Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr B7 Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 182 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54380S Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 183 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
N10C API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Off Spec Crude Oil
Flanged, 150#, ASME B 16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D
450 325 Type of Construction
Air Test psi (g)
SHEET NO. 54398 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 8" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM A216 Gr WCB) + 3 mm Inconel 625 Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 184 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
SHEET NO. 54398 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 185 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class B
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
N10B (0.5" - 20") N10C (0.5" - 6") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Off Spec Crude Oil
Flanged, 150#, ASME B 16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D/ ASME B 16.10
450 325 Type of Construction
Air Test psi (g)
SHEET NO. 54399 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 20" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged ASTM B564-UNS N06625 (Note 15) Body / Body Cover Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr 2H Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 186 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54399 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve (0.5" - 20") (LO)/ Lock-Closed (LC) provision. 11. All Ball-Valves shall be providedN10B with Lock-Open 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Valves with Carbon Steel Body (ASTM A105N [0.5"-1.5"] & ASTM A216 GR WCB [2"-6"]) with 3 mm Inconel 625 lining may be considered if size permits.
Page 187 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
54411 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO.
C35B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Oil/ Condensate, Glycol ASME B 16.34 1125 825
Description
Type of Construction
Body / Body Cover
Forged / Cast
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 1/2" - 14" Rating 300# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 300#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 14") UNS S32750 / S32760 UNS S32750 / S32760 ASTM A105N / UNS S32750 / S32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750
Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal (Note 14) Gland Retaining Nut Forged / Machined Wrench / Lever (Note 14) Body Stud / Nuts (Note 14) Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 188 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
SHEET NO. 54411 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 189 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
S30A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D
Type of Construction
Air Test psi (g)
54461 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 2" - 12" 300# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution
1100 800
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM A 351 Gr CF8M Solid (Note 9) SS 316 Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 190 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54461 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve mounted. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shallBall be trunnion 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 191 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description Body / Body Cover
S30B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Condensate, Glycol ASME B 16.34 1100 800
SHEET NO. 54463 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 16" Size Range 300# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 300#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body Bonnet cavity pressure to the upstream side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80
Type of Construction
Material of Construction
Forged / Cast
ASTM A 182 Gr F 316/ 316L Dual Stamped (1/2" - 1 1/2")/ ASTM A 351 Gr CF8M (2" - 12")
Manufacturer's Alternate/ Acceptance
Solid (Note 9) UNS S32750/ S32760 Ball Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 192 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54463 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 193 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q35A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water
ASME B 16.24 775 575 Type of Construction
SHEET NO. 54478 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 3" - 32" Rating 300# Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 300#, ASME B16.5, RF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM B 148 UNS C95800 Solid (Note 9) Ball Monel / NI-AL-Bronze Anti Blow Out (No Casting) Stem Monel / NI-AL-Bronze Bolted / Retained by Nuts & Washer Gland Monel / NI-AL-Bronze Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 194 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54478 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 195 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 F30A
Piping Class Manuf. Standard Testing Standard
API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Services / Fluids
Brackish Water
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
ASME B 16.24 775 575
SHEET NO. 54478F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry 2" - 24" Size Range 300# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side. Flanged, 300#, ASME B16.5, FF, Finish 125 AARH Face to Face dimension API 6D Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Body / Body Cover
Cast
ASTM B 148 UNS C95800
Ball
Solid (Note 9)
Monel / NI-AL-Bronze
Manufacturer's Alternate/ Acceptance
Stem Anti Blow Out (No Casting) Monel / NI-AL-Bronze Gland Bolted / Retained by Nuts & Washer Monel / NI-AL-Bronze Body Seat Soft Seat (Note 7) RPTFE Body Seals Soft Seal RPTFE/ PTFE/ Graphoil Stem Seal Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Gland Retaining Nut (Note 16) ASTM A194 Gr B7 Wrench / Lever Forged / Machined Carbon Steel / Malleable Iron Body Stud / Nuts (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Gland Bolts (Note 16) ASTM A193 Gr B7 Name Plate Corrosion Resistant SS/ Ni Alloy Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. Page 196 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54478F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
Page 197 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
54479 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO.
C35B (0.5"-8") F30B (0.5"-1.5") Q35B (0.5"-24")
API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Oil/ Condensate, Glycol, Oily Water, Effluent Water ASME B 16.34 1125 825
Description
Type of Construction
Body / Body Cover
Forged / Cast
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 1/2" - 24" Rating 300# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 300#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A 182 Gr F 53 (1/2" - 3")/ ASTM A 995 Gr 5A/ 6A (4" - 24") (Note 14) UNS S32750/ 32760 (Note 14) UNS S32750/ 32760 UNS S32750/ 32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B8M ASTM A194 Gr 8M ASTM A193 Gr B8M SS/ Ni Alloy Inconel X-750
Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal Gland Retaining Nut Forged / Machined Wrench / Lever B Body Stud / Nuts Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 198 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54479 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
C35B (0.5"-8") Ball Valve 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14.Ball valves in the size range of 16" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.
Page 199 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
F30B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water, Oily Water
ASME B 16.34 1125 825 Type of Construction
SHEET NO. 54479F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 2" - 24" Rating 300# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 300#, ASME B16.5, FF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM A 995 Gr 5A/ 6A (Note 14) Solid (Note 9) Ball UNS S32750/ 32760 (Note 14) Anti Blow Out (No Casting) Stem UNS S32750/ 32760 Bolted / Retained by Nuts & Washer Gland UNS S32750/ 32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 200 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54479F Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. Ball valves in the size range of 16" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.
Page 201 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q35A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Brackish Water
Flanged, 300#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D
1125 825 Type of Construction
Air Test psi (g)
SHEET NO. 54482 Contractor Document Number
Rev
50489-530-051-SPC-1002
A
Ball Valve FULL BORE Split Body, Side Entry 2" 300# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM A 995 Gr 5A/ 6A Solid (Note 9) Ball UNS S32750/ 32760 Anti Blow Out (No Casting) Stem UNS S32750/ 32760 Bolted / Retained by Nuts & Washer Gland UNS S32750/ 32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever B ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 202 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54482 Contractor Document Number
Rev
50489-530-051-SPC-1002
A
Ball Valve
Page 203 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
N30C API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Off Spec Crude Oil
Flanged, 300#, ASME B 16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D
1125 825 Type of Construction
Air Test psi (g)
SHEET NO. 54498 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 8" - 16" 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM A216 Gr WCB) + 3 mm Inconel 625 Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr 2H Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 204 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.
SHEET NO. 54498 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 205 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class B
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
N30B (0.5" - 16") N30C (0.5" - 6") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Off Spec Crude Oil
Flanged, 300#, ASME B 16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D/ ASME B 16.10
1125 825 Type of Construction
Air Test psi (g)
SHEET NO. 54499 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 1/2" - 16" B 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged ASTM B564-UNS N06625 (Note 15) Body / Body Cover Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr 2H Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 206 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54499 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve (0.5" - 16") (LO)/ Lock-Closed (LC) provision. 11. All Ball-Valves shall be providedN30B with Lock-Open 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Valves with Carbon Steel Body (ASTM A105N [0.5"-1.5"] & ASTM A216 GR WCB [2"-6"]) with 3 mm Inconel 625 lining may be considered if size permits.
Page 207 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
54511 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO.
C65B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Oil/ Condensate, Glycol ASME B 16.34 2225 1650
Description
Type of Construction
Body / Body Cover
Forged / Cast
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 1/2" - 24" Rating 600# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 600#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 24") UNS S32750/ S32760 (Note 15) UNS S32750/ S32760 ASTM A105N / UNS S32750/ S32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750
Solid (Note 9,15) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal (Note 14) Gland Retaining Nut Forged / Machined Wrench / Lever (Note 14) Body Stud / Nuts (Note 14) Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 208 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
SHEET NO. 54511 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 16" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.
Ball Valve
Page 209 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
S60A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292
Valve Type Size Range Rating Ends
Flanged, 600#, ASME B16.5, RF, Finish 125 AARH
ASME B 16.34
Face to Face dimension API 6D
Type of Construction
Air Test psi (g)
54561 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve FULL BORE Split Body, Side Entry 2" - 12" 600# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.
Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution
2175 1600
SHEET NO.
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast Body / Body Cover ASTM A 351 Gr CF8M Solid (Note 9) SS 316 Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 210 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54561 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Valve mounted. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shallBall be trunnion 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
Page 211 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
54579 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION
14050489 Piping Class
SHEET NO.
C65B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Oil/ Condensate, Glycol ASME B 16.34 2250 1650
Description
Type of Construction
Body / Body Cover
Forged / Cast
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 1/2" - 6" Rating 600# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 600#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
ASTM A 182 Gr F 53 (1/2" - 1 1/2")/ ASTM A 995 Gr 5A/ 6A (2" - 6") UNS S32750/ 32760 UNS S32750/ 32760 UNS S32750/ 32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B8M ASTM A194 Gr 8M ASTM A193 Gr B8M SS/ Ni Alloy Inconel X-750
Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal Gland Retaining Nut Forged / Machined Wrench / Lever Body Stud / Nuts B Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 212 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54579 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 213 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q95B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water
ASME B 16.34 3375 2475 Type of Construction
SHEET NO. 54679 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 3" - 24" Rating 900# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 900#, ASME B16.5, RTJ, Finish 32- 2. Floating Ball Valves shall be provided with pressure equalisation seals to 63 AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Cast ASTM A 995 Gr 5A/ 6A (Note 14) Body / Body Cover Solid (Note 9) Ball UNS S32750/ S32760 (Note 14) Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever B ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 214 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
SHEET NO. 54679 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. Ball valves in the size range of 8" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.
Page 215 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION
14050489 Piping Class Manuf. Standard Testing Standard
Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description
Q95B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water
ASME B 16.34 5625 4125 Type of Construction
SHEET NO. 54779 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 1/2" - 2" 1500# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 1500#, ASME B16.5, RTJ, Finish 32- 2. Floating Ball Valves shall be provided with pressure equalisation seals to 63 AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)
80 Material of Construction
Manufacturer's Alternate/ Acceptance
Forged Body / Body Cover ASTM A 182 Gr F 53 Solid (Note 9) Ball UNS S32750/ S32760 Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 216 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489
VALVE MATERIAL SPECIFICATION
11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.
SHEET NO. 54779 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
Ball Valve
Page 217 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
55411
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C35B
Manuf. Standard Testing Standard Services (Sour) Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
API 599 BS 6755 Pt. 1 / API 598 Hydrocarbon Oil / Condensate, Glycol ASME B 16.34 1125 825
Description
PLUG VALVE Valve Type PRESSURE BALANCED, TAPER PLUG Short Pattern 1/2" - 12" Size Range 300# Rating Ends Special Requirements Flanged, 300#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B16.10 Air Test psi (g)
80
Type of Construction
Material of Construction
Wrench
(Note 4)
Carbon Steel / SS / SG Iron
Name Plate
Corrosion Resistant
SS / Ni Alloy
Firesafe
Graphite / Graphite Filament
Emergency Packing injectable on stream
Manufacturer's Standard (Non Asbestos)
(Note 13)
ASTM A 193 Gr B7
Cover Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Gland
Renewable with valve open on stream
ASTM A 105N / ASTM A 216 Gr WCB
Plug
Inverted Taper
Stem
Forged / Bar
Cover
Forged/ Cast
ASTM A 105N / ASTM A 216 Gr WCB
Body
Forged/ Cast
ASTM A 105N / ASTM A 216 Gr WCB
Manufacturer's Alternate/ Acceptance
Stem Seal Cover Bolts / Nuts
ASTM A 194 Gr 2H
ASTM A 105N / ASTM A 216 WCB / WCC + ENP + Anti friction impregnated ASTM A 105N / AISI 4140 / 17-4 PH + Anti friction impregnated
Page 218 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
SHEET NO. 55411 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489
PLUG VALVE General Notes : 1.This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Vendor shall supply bolting for the tapped holes if any as per ASME B 16.5. 4. For wrench-operated Plug-Valves, separate wrench shall be provided for each Plug-Valve. 5. All Plug Valves shall be of fire safe design. Fire safe test shall be as per API 607 IV Edition / BS EN ISO 10497 ( BS 6755 Part II ) /API RP 6FA. 6. Seating surface shall be stellied for abrasion and chloride resistance. Soft Seats to achieve a seal between body and plug shall not be accepted. 7. All Plug Valves shall be provided with position indicator 8. Vendor shall confirm suitability of lubricant with respect to service & service conditions specified 9. Vendor shall supply lubricant for two years of normal operation. 10. Unless otherwise specified in MR , valves shall be Short Pattern type upto 12" & Venturi type above 12" size. 12. All Plug Valves shall have provision of seat sealant injection under full line pressure. 13. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 14. Third party inspection shall be conducted as per KOC Standard, KOC-MP-016.
Page 219 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
55511
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C65B
Manuf. Standard
API 599
Testing Standard
BS 6755 Pt. 1 / API 598
Services (Sour)
Hydrocarbon Gas / Oil / Condensate, Glycol
Pressure -Temperature Rating
2225 1650
Description
Size Range Rating Ends
1/2" - 24" 600# Special Requirements
Flanged, 600#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B16.10
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
Valve Type
PLUG VALVE PRESSURE BALANCED, TAPER PLUG
Air Test psi (g)
80
Type of Construction
Material of Construction
Wrench
(Note 4)
Carbon Steel / SS / SG Iron
Name Plate
Corrosion Resistant
SS / Ni Alloy
Firesafe
Graphite/ Graphite Filament
Emergency Packing injectable on stream
Manufacturer's Standard (Non Asbestos)
Cover Bolts / Nuts
(Note 13)
ASTM A 193 Gr B7
Cover Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Gland
Renewable with valve open on stream
ASTM A 105N / ASTM A 216 Gr WCB
Plug
Inverted Taper
ASTM A 105N / ASTM A 216 WCB / WCC + ENP + Anti friction impregnated
Stem
Forged / Bar
ASTM A 105N / AISI 4140 / 17-4 PH + Anti friction impregnated
Cover
Forged/ Cast
ASTM A 105N / ASTM A 216 Gr WCB
Body
Forged/ Cast
ASTM A 105N / ASTM A 216 Gr WCB
Manufacturer's Alternate/ Acceptance
Stem Seal ASTM A 194 Gr 2H
Page 220 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
SHEET NO. 55511 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489
PLUG VALVE General Notes : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Vendor shall supply bolting for the tapped holes if any as per ASME B 16.5. 4. For wrench-operated Plug-Valves, separate wrench shall be provided for each Plug-Valve. 5. All Plug Valves shall be of fire safe design. Fire safe test shall be as per BS EN ISO 10497 ( BS 6755 Part II ) /API RP 6FA. 6. Seating surface shall be stellied for abrasion and chloride resistance. Soft Seats to achieve a seal between body and plug shall not be accepted. 7. All Plug Valves shall be provided with position indicator 8. Vendor shall confirm suitability of lubricant with respect to service & service conditions specified 9. Vendor shall supply lubricant for two years of normal operation. 10. Unless otherwise specified in MR , valves shall be Short Pattern type upto 12" & Venturi type above 12" size. 12. All Plug Valves shall have provision of seat sealant injection under full line pressure. 13. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 14. Third party inspection shall be conducted as per KOC Standard, KOC-MP-016.
Page 221 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
B
KOC Contract No
55511L Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C65B
Manuf. Standard
API 599
Testing Standard
BS 6755 Pt. 1 / API 598
Services (Sour)
Hydrocarbon Gas / Oil / Condensate, Glycol
Pressure -Temperature Rating
ASME B 16.34
Hydro Test Pressure Body psi (g) Seat psi (g)
2225 1650
Description
Valve Type
PLUG VALVE PRESSURE BALANCED, TAPER PLUG
Size Range Rating Ends
1/2" - 24" 600# Special Requirements
Flanged, 600#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH 2. Valve shall be provided with Limit Switches as per applicable KOC standard. Face to Face dimension ASME B16.10 Air Test psi (g)
80
Type of Construction
Material of Construction
Wrench
(Note 4)
Carbon Steel / SS / SG Iron
Name Plate
Corrosion Resistant
SS / Ni Alloy
Firesafe
Graphite/ Graphite Filament
Emergency Packing injectable on stream
Manufacturer's Standard (Non Asbestos)
Cover Bolts / Nuts
(Note 13)
ASTM A 193 Gr B7
Cover Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Gland
Renewable with valve open on stream
ASTM A 105N / ASTM A 216 Gr WCB
Plug
Inverted Taper
ASTM A 105N / ASTM A 216 WCB / WCC + ENP + Anti friction impregnated
Stem
Forged / Bar
ASTM A 105N / AISI 4140 / 17-4 PH + Anti friction impregnated
Cover
Forged/ Cast
ASTM A 105N / ASTM A 216 Gr WCB
Body
Forged/ Cast
ASTM A 105N / ASTM A 216 Gr WCB
Manufacturer's Alternate/ Acceptance
Stem Seal ASTM A 194 Gr 2H
Page 222 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
SHEET NO. B
55511L Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489
PLUG VALVE General Notes : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Vendor shall supply bolting for the tapped holes if any as per ASME B 16.5. 4. For wrench-operated Plug-Valves, separate wrench shall be provided for each Plug-Valve. 5. All Plug Valves shall be of fire safe design. Fire safe test shall be as per BS EN ISO 10497 ( BS 6755 Part II ) /API RP 6FA. 6. Seating surface shall be stellied for abrasion and chloride resistance. Soft Seats to achieve a seal between body and plug shall not be accepted. 7. All Plug Valves shall be provided with position indicator 8. Vendor shall confirm suitability of lubricant with respect to service & service conditions specified 9. Vendor shall supply lubricant for two years of normal operation. 10. Unless otherwise specified in MR , valves shall be Short Pattern type upto 12" & Venturi type above 12" size. 12. All Plug Valves shall have provision of seat sealant injection under full line pressure. 13. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 14. Third party inspection shall be conducted as per KOC Standard, KOC-MP-016.
Page 223 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
56311
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C15B
Manuf. Standard
API 609 Cat B
Testing Standard
API 598
Services (Sour)
Hydrocarbon Gas/ Oil/ Condensate, Glycol
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
ASME B 16.34 450 325
BUTTERFLY VALVE Valve Type Size Range Rating Ends WAFL, 150# RF ASME B16.5 (3" -24")
3" - 24" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.
Face to Face dimension API 609 Cat B Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy UNS S32750 / S32760
Shaft Bushing Shaft seal
Renewable
Graphite with Inconel Wire
Disc Seal
Replaceble
Graphite with Inconel Wire
Clamping Rings (If required) Bolts
Manufacturer's Alternate/ Acceptance
UNS S32750 / S32760 Nuts
Machined
ASTM A193 Gr B7
ASTM A 194 Gr 2H
UNS S32750 / S32760
Body Screws / Pin Shaft
Anti Static, No Casting
UNS S32750 / S32760
Body Seat
Renewable
UNS S32750 / S32760
Disc
Cast
UNS S32750 / S32760
Body
Cast
ASTM A 216 Gr WCB
Page 224 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
SHEET NO. 56311 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489
BUTTERFLY VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Bidder to furnish cross sectional details of body seat / seal arrangement with the offer 5. Bolting for Tapped holes in body, if any, shall be supplied by vendor in material ASTM A 193 GR.B7/A 194 GR.2H. 6. Valves shall be provided with position indicator and locking device at any position 7. Valves shall be tight shut off and shall be bi-directional. 8. Valves shall be of fire safe design as per API 607 or ISO 10497 or API 6FA. 9. Shaft seal shall be provided with corrosion inhibitor
Page 225 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
56312
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C15B
Manuf. Standard
API 609 Cat B
Testing Standard
API 598
Services (Sour)
Hydrocarbon Gas/ Oil/ Condensate
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
ASME B 16.34 450 325
BUTTERFLY VALVE Valve Type Size Range Rating Ends WAFL, 150# RF ASME B16.5 (3" -24")
3" - 24" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This Valve Data Sheet shall be applicable for Process Gas (PG), Fuel Gas (FG) and Blowdown (BD) services only
Face to Face dimension API 609 Cat B Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy SS316L
Shaft Bushing Shaft seal
Renewable
Graphite with Inconel Wire
Disc Seal
Replaceble
Graphite with Inconel Wire
Clamping Rings (If required) Bolts
Manufacturer's Alternate/ Acceptance
SS316L Nuts
Machined
ASTM A193 Gr B7
ASTM A 194 Gr 2H
SS316L
Body Screws / Pin Shaft
Anti Static, No Casting
SS316L
Body Seat
Renewable
SS316L
Disc
Cast
ASTM A 216 Gr WCB + SS316 overlay
Body
Cast
ASTM A 216 Gr WCB
Page 226 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
SHEET NO. 56312 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489
BUTTERFLY VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Bidder to furnish cross sectional details of body seat / seal arrangement with the offer 5. Bolting for Tapped holes in body, if any, shall be supplied by vendor in material ASTM A 193 GR.B7 / A 194 GR.2H. 6. Valves shall be provided with position indicator and locking device at any position 7. Valves shall be tight shut off and shall be bi-directional. 8. Valves shall be of fire safe design as per API 607 or ISO 10497 or API 6FA. 9. Shaft seal shall be provided with corrosion inhibitor
Page 227 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
56381
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
Q15A
Manuf. Standard
API 609 Cat B
Testing Standard
API 598
Services (Sour)
Brackish Water
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
ASME B 16.24 300 220
BUTTERFLY VALVE Valve Type Size Range Rating Ends
3" - 24" 150# Special Requirements
WAFL, 150#, RF ASME B16.5 (3" -24") Face to Face dimension API 609 Cat B Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy Ni Al Bronze / Monel
Shaft Bushing Shaft seal
Renewable
Graphite with Inconel Wire
Disc Seal
Replaceble
Graphite with Inconel Wire
Clamping Rings (If required) Bolts
Manufacturer's Alternate/ Acceptance
Ni Al Bronze / Monel Nuts
Machined
ASTM A193 Gr B7
ASTM A 194 Gr 2H
Ni Al Bronze / Monel
Body Screws / Pin Shaft
Anti Static, No Casting
Ni Al Bronze / Monel
Body Seat
Renewable
Ni Al Bronze / Monel
Disc
Cast
Ni Al Bronze / Monel
Body
Cast
ASTM A 216 Gr WCB - EPDM Lined
Page 228 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
SHEET NO. 56381 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489
BUTTERFLY VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Bidder to furnish cross sectional details of body seat / seal arrangement with the offer 5. Bolting for Tapped holes in body, if any, shall be supplied by vendor in material ASTM A 193 GR.B7 / A 194 GR.2H. 6. Valves shall be provided with position indicator and locking device at any position 7. Valves shall be tight shut off and shall be bi-directional. 8. Valves shall be of fire safe design as per API 607 or ISO 10497 or API 6FA. 9. Shaft seal shall be provided with corrosion inhibitor
Page 229 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
56478
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
Q35A
Manuf. Standard
API 609 Cat B
Testing Standard
API 598
Services (Sour)
Brackish Water
Pressure -Temperature Rating
ASME B 16.24
Hydro Test Pressure Body psi (g) Seat psi (g)
300 220
BUTTERFLY VALVE Valve Type Size Range Rating Ends
3" - 24" 300# Special Requirements
WAFL, 150# RF ASME B16.5 (3" -24") Face to Face dimension API 609 Cat B Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy Ni Al Bronze / Monel
Shaft Bushing Shaft seal
Renewable
Graphite with Inconel Wire
Disc Seal
Replaceble
Graphite with Inconel Wire
Clamping Rings (If required) Bolts
Manufacturer's Alternate/ Acceptance
Ni Al Bronze / Monel Nuts
Machined
ASTM A193 Gr B7
ASTM A 194 Gr 2H
Ni Al Bronze / Monel
Body Screws / Pin Shaft
Anti Static, No Casting
Ni Al Bronze / Monel
Bonnet Gasket
Flat Ring
Compressed Non-Asbestos Fibre
Body Seat
Renewable
Ni Al Bronze / Monel Ni Al Bronze / Monel
Disc Body
Cast
ASTM B 148 C95800
Page 230 of 237
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
SHEET NO. 56478 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489
BUTTERFLY VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Bidder to furnish cross sectional details of body seat / seal arrangement with the offer 5. Bolting for Tapped holes in body, if any, shall be supplied by vendor in material ASTM A 193 GR.B7 / A 194 GR.2H. 6. Valves shall be provided with position indicator and locking device at any position 7. Valves shall be tight shut off and shall be bi-directional. 8. Valves shall be of fire safe design as per API 607 or ISO 10497 or API 6FA. 9. Shaft seal shall be provided with corrosion inhibitor
Page 231 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
57082
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
Q35A
Manuf. Standard
BS EN ISO 15761
Testing Standard
API 598/ BS 6755 Pt. 1
Services
NEEDLE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements
Valve Type Size Range Rating Ends
Hydrocarbon Oil / Condensate, Oily Water
SW, 3000 # to ASME B 16.11
ASME B 16.34
Face to Face dimension Manufacturer's Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
3000 2200
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy
Stem Sleeve/ Nut
Forged/ Machined
ASTM A 439 Type D-2 / D-2C
Stem
Forged / Bar (No Casting)
UNS S32750/ S32760
Gland Packing
Renewable with Valve on stream
Graphite with Inconel Wire
Back Seat Bush
-
UNS S32750/ S32760
Bonnet Bolts / Nuts
ASTM A 193 Gr B8M
Manufacturer's Alternate/ Acceptance
ASTM A 194 Gr 8M
Bonnet
Bolted
ASTM A 182 Gr F 53
Bonnet Gasket
Flat Ring
Compressed Non-Asbetos Fibre
Body Seat Ring
Renewable / Integral
UNS S32750/ S32760
Disc
Loose Plug Type
UNS S32750/ S32760
Body
Forged
ASTM A 182 Gr F 53
B
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 4. Gland packing shall be provided with corrosion Inhibitors
Page 232 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
57311
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C15B
Manuf. Standard
BS EN ISO 15761
Testing Standard
API 598/ BS 6755 Pt. 1
NEEDLE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 150# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Services
Hydrocarbons Gas / Oil / Condensate, Glycol
Flanged, 150#, ASME B16.5
ASME B 16.34
Face to Face dimension Manufacturer's Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
450 325
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy
Stem Sleeve/ Nut
Forged/ Machined
ASTM A 439 Type D-2 / D-2C
Stem
Forged / Bar (No Casting)
UNS S32750 / S32760
Gland Packing
Renewable with Valve on stream
Graphite with Inconel Wire
Back Seat Bush
-
UNS S32750 / S32760
Bonnet Bolts / Nuts
(Note 3)
ASTM A 193 Gr B7
Bonnet
Bolted
ASTM A 105N
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Body Seat Ring
Renewable / Integral
UNS S32750 / S32760
Disc
Loose Plug Type
UNS S32750 / S32760
Body
Forged
ASTM A 105N
ASTM A 194 Gr 2H
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Gland packing shall be provided with corrosion Inhibitors Page 233 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
57312
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C15B
Manuf. Standard
BS EN ISO 15761
Testing Standard
API 598/ BS 6755 Pt. 1
Services
NEEDLE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 150# Special Requirements
Valve Type Size Range Rating Ends
Hydrocarbons Gas / Oil / Condensate
Flanged, 150#, ASME B16.5
ASME B 16.34
Face to Face dimension Manufacturer's Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
450 325
Air Test psi (g)
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This Valve Data Sheet shall be applicable for Process Gas (PG), Fuel Gas (FG) and Blowdown (BD) services only.
80
Description
Type of Construction
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy
Stem Sleeve/ Nut
Forged/ Machined
ASTM A 439 Type D-2 / D-2C
Stem
Forged / Bar (No Casting)
SS316L
Gland Packing
Renewable with Valve on stream
Graphite with Inconel Wire
Back Seat Bush
-
SS316L
Bonnet Bolts / Nuts
(Note 3)
ASTM A 193 Gr B7
Bonnet
Bolted
ASTM A 105N
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Body Seat Ring
Renewable / Integral
SS316L
Disc
Loose Plug Type
SS316L
Body
Forged
ASTM A 105N
ASTM A 194 Gr 2H
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Gland packing shall be provided with corrosion Inhibitors Page 234 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
57379
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
Q15B
Manuf. Standard
BS EN ISO 15761
Testing Standard
API 598/ BS 6755 Pt. 1
NEEDLE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 150# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Services
Hydrocarbon Oil / Condensate, Oily Water
Flanged, 150#, ASME B16.5
ASME B 16.34
Face to Face dimension Manufacturer's Standard
Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)
450 325
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy
Stem Sleeve/ Nut
Forged/ Machined
ASTM A 439 Type D-2 / D-2C
Stem
Forged / Bar (No Casting)
UNS S32750 / S32760
Gland Packing
Renewable with Valve on stream
Graphite with Inconel Wire
Back Seat Bush
-
UNS S32750/ S32760
Bonnet Bolts / Nuts
ASTM A 193 Gr B8M
Manufacturer's Alternate/ Acceptance
ASTM A 194 Gr 8M
Bonnet
Bolted
ASTM A 182 Gr F 53
Bonnet Gasket
Flat Ring
Compressed Non-Asbetos Fibre
Body Seat Ring
Renewable / Integral
UNS S32750 / S32760
Disc
Loose Plug Type
UNS S32750 / S32760
Body
Forged
ASTM A 182 Gr F 53
B
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 4. Gland packing shall be provided with corrosion Inhibitors
Page 235 of 237
SHEET NO.
Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT
57411
KOC Contract No
Contractor Document Number
Rev
50489-530-051-SPC-1002
B
VALVE MATERIAL SPECIFICATION 14050489 Piping Class
C35B
Manuf. Standard
BS EN ISO 15761
Testing Standard
API 598/ BS 6755 Pt. 1
NEEDLE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 300# Special Requirements
Valve Type Size Range Rating Ends
1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Services
Pressure -Temperature Rating
Hydrocarbons Oil / Condensate, Glycol
Flanged, 300#, ASME B16.5
ASME B 16.34
Face to Face dimension Manufacturer's Standard
Hydro Test Pressure Body psi (g) Seat psi (g)
1125 825
Air Test psi (g)
80
Description
Type of Construction
Material of Construction
Manufacturer's Alternate/ Acceptance
Handwheel
Cast / Fabricated
Ductile Iron/ Malleable Iron / Cast Steel
Name Plate
Corrosion Resistant
SS/ Ni Alloy
Stem Sleeve/ Nut
Forged/ Machined
ASTM A 439 Type D-2 / D-2C
Stem
Forged / Bar (No Casting)
UNS S32750 / S32760
Gland Packing
Renewable with Valve on stream
Graphite with Inconel Wire
Back Seat Bush
-
UNS S32750 / S32760
Bonnet Bolts / Nuts
(Note 3)
ASTM A 193 Gr B7
Bonnet
Bolted
ASTM A 105N
Bonnet Gasket
Spiral Wound
Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring
Body Seat Ring
Renewable / Integral
UNS S32750 / S32760
Disc
Loose Plug Type
UNS S32750 / S32760
Body
Forged
ASTM A 105N
ASTM A 194 Gr 2H
GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Gland packing shall be provided with corrosion Inhibitors Page 236 of 237
Project Title CONSTRUCTION OF NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No
VALVE MATERIAL SPECIFICATION
14050489
Page No : 237 of 237 Contractor Document Number
Rev
50489-530-051-SPC-1002
B
APPENDIX-III TABLE – 2: BALL VALVE NIPPLE DETAILS Sr. No.
Sheet No.
Piping Class
Size (Inch)
Nipple Description
1
54001
C13A
0.5
PIPE NIPPLE SEAMLESS PBE 1/2" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M
2
54001, 54001X
C13A
0.75
PIPE NIPPLE SEAMLESS PBE 3/4" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M
3
54001, 54001X
C13A
1
PIPE NIPPLE SEAMLESS PBE 1" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M
4
54001, 54001X
C13A
1.5
PIPE NIPPLE SEAMLESS PBE 1 1/2" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M
5
54001S
C13A
0.5
PIPE NIPPLE SEAMLESS TOE 1/2" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN X THREADED (NPT M) ASME B36.10M
6
54082
F30A, Q35A
0.5
PIPE NIPPLE SEAMLESS PBE 1/2" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M
7
54082, 54082X
F30A, Q35A
0.75
PIPE NIPPLE SEAMLESS PBE 3/4" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M
8
54082, 54082X
F30A, Q35A
1
PIPE NIPPLE SEAMLESS PBE 1" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M
9
54082, 54082X
F30A, Q35A
1.5
PIPE NIPPLE SEAMLESS PBE 1 1/2" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M
10
54082S
F30A, Q35A
0.5
PIPE NIPPLE SEAMLESS TOE 1/2" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 80S PLAIN X THREADED (NPT M) ASME B36.19M
11
54061
S10A, S30A, S60A
0.5
PIPE NIPPLE SEAMLESS PBE 1/2" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M
12
54061, 54061X
S10A, S30A, S60A
0.75
PIPE NIPPLE SEAMLESS PBE 3/4" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M
13
54061, 54061X
S10A, S30A, S60A
1
PIPE NIPPLE SEAMLESS PBE 1" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M
14
54061, 54061X
S10A, S30A, S60A
1.5
PIPE NIPPLE SEAMLESS PBE 1 1/2" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M
15
54061S
S10A, S30A, S60A
0.5
PIPE NIPPLE SEAMLESS TOE 1/2" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 80S PLAIN X THREADED (NPT M) ASME B36.19M