IEC-61082_3.pdf

BS EN 61082-3:1994 IEC 1082-3: 1993

BRITISH STANDARD

Preparation of documents used in electrotechnology — Part 3: Connection diagrams, tables and lists

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

The European Standard EN 61082-3:1994 has the status of a British Standard

UDC 621.3.061:003.62

Copyright British Standards Institution Reproduced by IHS under license with BSI - Uncontrolled Copy No reproduction or networking permitted without license from IHS

Not for Resale

BS EN 6108 61082-3: 2-3:1994 1994

Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees of the following countries: Austria Belgium Denmark Finland France Germany Greece Iceland Ireland

This British Standard, having been prepared under the direction direction of the General General Electrotechnical Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 April 1994 © BSI 02-1999

Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland United Kingdom

Amendments issued since publication

Amd. No.

Date

Comments

The following BSI references relate to the work on this standard: Committee reference GEL/3 Draft for comment 92/86327 DC ISBN 0 580 23078 3 --`,,```,,,,````-`-`,,`,,`,`,,`---


Not for Resale

BS EN 61082-3:1994

Contents Cooperating organizations National foreword Foreword Text of EN 61082-3 National annex NA (informative) Committees responsible National annex NB (informative) Cross-references

Page Inside front cover ii 2 5 Inside back cover Inside back cover

--`,,```,,,,````-`-`,,`,,`,`,,`---

i

© BSI 02-1999


Not for Resale

BS EN 61082-3:1994

National foreword This British Standard has been prepared under the direction of the General Electrotechnical Standards Policy Committee and is the English language version of EN 61082-3:1994 Preparation of documents used in electrotechnology. Part 3: Connection diagrams, tables and lists, published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC 1082-3:1993 published by the International Electrotechnical Commission (IEC). IEC 1082 consists of several Parts as follows: IEC 1082-1:1991, General requirements. IEC 1082-2:1993, Function-oriented diagrams. IEC 1082-3:1993, Connection diagrams, tables and lists. IEC 1082-4, Location and installation documents (in preparation). Other Parts under consideration are: — Parts’ lists — Spare parts’ lists — Instructions It is envisaged that all Parts of IEC 1082 will be adopted by CENELEC as Parts of EN 61082. British Standards identical in number and title will be published as further Parts of BS EN 61082 in due course. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.

Summary of pages

This document comprises a front cover, an inside front cover, pages i to iv, the EN title page, pages 2 to 22, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. --`,,```,,,,````-`-`,,`,,`,`,,`---

© BSI 02-1999

ii


Not for Resale

EUROPEAN STANDARD

EN 61082-3

NORME EUROPÉENNE ` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

January 1994

EUROPÄISCHE NORM UDC 621.3.061:003.62

Supersedes HD 246.5 S1:1977 and HD 246.6 S2:1988

Descriptors: Electrotechnology, documents, connections, diagrams

English version

Preparation of documents used in electrotechnology Part 3: Connection diagrams, tables and lists (IEC 1082-3:1993)

Etablissement des documents utilisés en électrotechnique Partie 3: Schémas, tableaux et listes des connexions (CEI 1082-3:1993)

Erstellung von in der Elektrotechnik verwendeten Dokumenten Teil 3: Schaltpläne, Tabellen und Listen (IEC 1082-3:1993)

This European Standard was approved by CENELEC on 1993-09-22. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels

© 1994 Copyright reserved to CENELEC members


Not for Resale

Ref. No. EN 61082-3:1994 E

EN 61082-3:1994

Foreword ` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

Contents

The text of document 3B(CO)50, as prepared by Subcommittee 3B: Documentation, of IEC Technical Committee No. 3: Documentation and graphical symbols, was submitted to the IEC-CENELEC parallel vote in November 1992. The reference document was approved by CENELEC as EN 61082-3 on 22 September 1993. This European Standard replaces HD 246.5 S1:1977 and HD 246.6 S2:1988. The following dates were fixed: — latest date of publication of an identical national standard (dop) 1994-12-01 — latest date of withdrawal of conflicting national standards (dow) 1994-12-01

Foreword Section 1. General 1.1 Scope 1.2 Normative references Section 2. Common rules for disconnection diagrams, tables and lists 2.1 General 2.2 Connection diagrams 2.3 Connection tables and lists Section 3. Unit connection diagrams and tables 3.1 General 3.21 Layout of diagrams 3.3 Examples Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is Section 4. Interconnection diagrams and tables normative. 4.1 General 4.2 Layout of diagrams 4.3 Examples Section 5. Terminal connection diagrams and tables 5.1 General 5.2 Examples Section 6. Cable diagrams, tables and lists 6.1 General 6.2 Examples Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications Figure 1 — Example of a unit connection diagram using continuous lines Figure 2 — Example of a unit connection diagram using interrupted lines Figure 3 — Example of a unit connection diagram with the conductors arranged in different cable bundles, using continuous lines Figure 4 — Examples of representations of connections using various types of cables Figure 5 — Example of a connection-oriented unit connection table. See subclause 3.3 for an explanation of the notation Figure 6 — Example of a unit connection diagram in matrix form for a sub-rack Figure 7 — Example of a unit connection diagram for a sub-rack

5 5 6 6 7 8 8 8 14 14 14 17 17 21 21

22 9 9

10 11 12 12 13

© BSI 02-1999

2


Page 2

Not for Resale

EN 61082-3:1994

Page Figure 8 — Example of an interconnection diagram using multi-line representation Figure 9 — Example of an interconnection diagram using partly single-line representation Figure 10 — Example of an interconnection diagram with cable end connectors Figure 11 — Example of an interconnection diagram in single-line representation, showing cable connectors Figure 12 — Example of a connection-oriented interconnection table Figure 13 — Example of two terminal connection diagrams Figure 14 — Example of two terminal connection diagrams with remote end designations Figure 15 — Example of two connection-oriented terminal connection tables with remote end designations Figure 16 — Example of a terminal-oriented terminal connection table Figure 17 — Example of a terminal connection table of grid type with remote end designations Figure 18 — Example of part of a cable diagram where groups of cables have been represented by single lines Figure 19 — Example of a cable diagram Figure 20 — Example of a cable diagram showing prefabricated cables provided with connectors Figure 21 — Example of a cable table

14 15 15 15 16 17 18 18 19 19 20 21 21 21

` , , ` , ` , , ` , , ` ` ` ` ` ` , , , , ` ` ` , , ` -

3

© BSI 02-1999


Not for Resale

` , , ` , ` , , ` , , ` ` ` ` ` ` , , , , ` ` ` , , ` -

4


blank Not for Resale

EN 61082-3:1994

Section 1. General 1.1 Scope This International Standard provides rules for connection diagrams, tables and lists.

IEC 445:1988, Identification of equipment terminals

NOTE According to IEC 1082-1, no difference between the terms table and list exists.

IEC 446:1989, Identification of conductors by

and of terminations of certain designated conductors, including general rules for an alphanumeric system. colours or numerals.

1.2 Normative references IEC 617-3:1983, Graphical symbols for diagrams — Part 3: Conductors and connecting devices. The following normative documents contain IEC 750:1983, Item designation in electrotechnology. provisions which, through reference in this text, constitute provisions of this part of IEC 1082. At the IEC 757:1983, Code for designation of colours. time of publication, the editions indicated were IEC 1082-1:1991, Preparation of documents used in valid. All normative documents are subject to electrotechnology — Part 1: General requirements. revision, and the parties to agreements based on this part of IEC 1082 are encouraged to investigate IEC 1082-2:1993, Preparation of documents used in the possibility of applying the most recent editions electrotechnology — Part 2: Function-oriented of the normative documents listed below. Members diagrams. of IEC and ISO maintain registers of currently valid International Standards.

--`,,```,,,,````-`-`,,`,,`,`,,`---

5

© BSI 02-1999


Not for Resale

EN 61082-3:1994

Section 2. Common rules for connection diagrams, tables and lists 2.1 General 2.2 Connection diagrams Connection documents provide information on 2.2.1 Layout physical connections among, for example, Connection diagrams should use topographical components, devices, assemblies, and installations. layout but need not be to scale. Connection documents are used when assembling, 2.2.2 Representation and identification of installing or maintaining equipment. devices and terminals Connection documents shall include information identifying the connection points of each connection Devices should be represented by simple outlines, such as squares, rectangles, or circles, or by and the conductors or cables used to make the simplified pictorial representations. Graphical connections. In the case of terminal connection symbols according to IEC 617 may also be used. documents, only one end need be shown. Other information may be included as needed or as Terminals shall be clearly indicated but symbols for appropriate, and shall be included to the extent that terminals need not be shown unless special conditions require their depiction. is required for the intended use of the document. 2.2.3 Representation and identification of The following types of information shall be conductors considered for inclusion: Conductors shall be represented using one of the — conductor or cable type information (for following methods: example, a recognized type designation, catalogue or part number, material, construction, a) Continuous line — where continuous lines size, colour of insulation, voltage rating, number represent the actual conductors between of conductors, other technical data); terminals. See Figure 1. Conductor groups, cables, cable bundles, etc. may be represented by — conductor or cable number or item designation; a single line. See Figure 3. — identification or representation of the If a unit or installation contains several connection points (for example, item and/or conductor groups, cables, cable bundles, etc., terminal designation, pictorial representations, these may be separated from one another and remote end designation); designated by item designations. See Figure 3, — instruction for, or methods of, laying, routing, cable bundles –W1 and –W2. termination, attachment, twisting, screening, b) Interrupted line — where the lines etc.; representing the conductors are interrupted and — length of conductor or cable; provision is made for the association of the — signal designation and/or technical data about interrupted lines. See Figure 2. the signal; and Symbols 03-02-04 and 03-02-05 in IEC 617 for a — special classification or information. junction of conductors (“T-junction”) shall not be For identification of conductors by means of colours used unless there is a physical junction. or numerals, see IEC 446. Colour codes shall be in Figure 4 shows a number of examples of how accordance with IEC 757. For identification of connections to various types of cables should be items, see IEC 750. represented. The information may be given in diagrammatic or 2.2.4 Matrix form tabular form, or a combination of these, provided If there are a large number of connections to be clarity is maintained. shown in a small space, as for example for the Connection documents shall be prepared in connections in a rack or subassembly containing accordance with the rules in IEC 1082-1 and in printed circuit boards, a matrix form of layout may accordance with the rules given in this Part of be advantageous. IEC 1082. The symbols for the terminals to be connected shall If any special convention is used, for example, to be arranged in a grid format, and each shall be indicate methods for attachment or removal, it should be shown or referenced in the document or in identified. All of the terminal symbols for a single device shall supporting documents. be aligned vertically [horizontally] in a sequence that provides a clear presentation of the connection information. The sequence need not conform to the physical sequence of the terminals on the device. ` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

© BSI 02-1999

6


Not for Resale

EN 61082-3:1994

The columns [rows] of terminal symbols thus formed shall be arranged horizontally [vertically]. Each conductor shall be represented by a horizontal [vertical] connecting line passing through the symbols for the terminals to be connected. Conductors carrying named signals shall have the signal designations shown at one end of the connecting line on diagrams intended for installation, operation, or maintenance. See Figure 6. If individual (point-to-point) conductors are to be shown exactly, each individual conductor shall be shown with a separate connecting line, if necessary. Conductor numbers may be shown, and, if shown, shall be placed above [to the left of] the respective horizontal [vertical] connecting lines. ` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

2.3 Connection tables and lists 2.3.1 Layout

Connection tables shall be prepared in one of the following forms: — terminal-oriented form. See Figure 16. — connection-oriented form. See Figure 5 and Figure 15. In the terminal-oriented form, each device to be connected shall be presented one by one together with its terminals. For each terminal, the attached connection(s) shall be shown. For example, see Figure 16. In the connection-oriented form, each connection (wire, cable, cable conductor, etc.) shall be presented one by one, each wire or each individual cable conductor grouped together with the other conductors in that cable. For each conductor, the connected terminals or end points shall be shown. For examples, see Figure 5, Figure 12, and Figure 15.

Devices shall be represented and identified by the item designations. Terminals shall be represented and identified by the terminal designations marked on the device or, as with a dual-in-line package or an electronic tube, assigned by the manufacturer or by convention. If there is no terminal designation assigned by the manufacturer to the device, arbitrary terminal designations shall be assigned and shall be explained in the table or in referenced supporting documents. The same terminal designation shall be used for the same terminal in all other documents in which a designation for the terminal appears. If the terminal designation has the form of a graphical symbol or colour, an equivalent standardized letter symbol may be used, for example, PE instead of the graphical symbol for protective earth (see IEC 445), BU for blue colour (see IEC 757). 2.3.3 Representation and identification of conductors

Conductors shall be represented and identified by using one or more of the following: — an item designation. See –W108 in Figure 8 and Figure 9. — a unique marking or colour found on the physical connection itself. See Figure 4. — an arbitrarily assigned identification number. See Figure 2, Figure 3, and Figure 5. — the set of terminals connected by the connection. See Figure 3 and Figure 15.

7

© BSI 02-1999


2.3.2 Representation and identification of devices and terminals

Not for Resale

EN 61082-3:1994

Section 3. Unit connection diagrams and tables 3.1 General Unit connection diagrams and tables shall provide all information required about the internal connections within a single constructional unit or assembly of units. Information about the external connections among units need not be included, but references to the appropriate interconnection diagram or table may be provided. 3.2 Layout of diagrams Symbols for devices should be arranged to generally correspond with the view of the equipment as seen when making the connections. More than one view may be required if the equipment is viewed from different directions when making the connections. Terminals need not be shown arranged in the same way as they are in the actual device. If devices are located above each other at several levels, these devices may be shown in the diagram as flipped, turned, or moved in such a way that the devices can be seen by the user of the diagram. The method used should be indicated. For example, see Figure 3, which contains a note indicating that the movable part to the right of the boundary line is wired from the front of the bay. 3.3 Examples Figure 1 shows an example of a simple unit connection diagram where the conductors are depicted by individual lines and identified by conductor numbers. Figure 2 shows an example of the unit shown in Figure 1, but with interrupted lines and with the graphical symbols for the terminals left out.

Figure 3 shows an example where the diagram shows the conductors grouped in two cable bundles, –W1 and –W2. The wires entering or leaving a cable bundle are shown in such a way that they are easily identifiable. Figure 5 shows an example of a connection-oriented unit connection table for the unit shown in Figure 1. The notation TWIST 1 for conductors 44 and 45 in the instruction column indicates that these conductors form a twisted pair. The conductors 46 and 47 form another twisted pair. The notation in the remarks column indicate that a second conductor or device is connected to the same terminal. A short dash in the conductor designation column indicates that no separate conductor is needed, i.e. the terminals of two components are directly connected, in this case each of the terminals of diode –V1 to terminals of –K13. The designation LINK indicates a physical link or a short wire without conductor number. Figure 6 shows an example of a unit connection diagram in matrix or grid form. It should be noted that the symbols for the terminals of each printed circuit board have been placed to suit the layout of the diagram. Compare the diagram in Figure 7, which shows the same equipment. A comparison between the two diagrams shows that, in this case, it has not been regarded necessary to show the exact physical connections.

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

© BSI 02-1999

8


Not for Resale

EN 61082-3:1994

Figure 1 — Example of a unit connection diagram using continuous lines

` , , ` , ` , , ` , , ` ` ` ` ` ` , , , , ` ` ` , , ` -

Figure 2 — Example of a unit connection diagram using interrupted lines

9

© BSI 02-1999


Not for Resale

E N 6 1 0 8 2 3 : 1 9 9 4

1 0

© B S I 0 2 -1 9 9 9

Figure 3 — Example of a unit connection diagram with the conductors arranged in different cable bundles, using continuous lines


Not for Resale

EN 61082-3:1994

Ex.

1

2

3

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , ,

Diagram

Description

Cable –W161, coming from unit +B5; Cable cores 1,2, and 3 connected to terminals 11, 12, and 13. The protective earth conductor PE connected to protective earth bar. The line representing the cable may be located at any point of the thick line at the splitting point. Screened cable –W165 with two twisted and screened pairs

Two cables, interlaced on the diagram; The cable cores of cable –W168 connected to terminals 11, 12, 14, 16, and 19, those of cable –W169 connected to terminals 13, 15, 18, 19, and 20.

EN 61082-3:1994

Ex.

Diagram

1

Description

Cable –W161, coming from unit +B5; Cable cores 1,2, and 3 connected to terminals 11, 12, and 13. The protective earth conductor PE connected to protective earth bar. The line representing the cable may be located at any point of the thick line at the splitting point. Screened cable –W165 with two twisted and screened pairs

2

3

Two cables, interlaced on the diagram; The cable cores of cable –W168 connected to terminals 11, 12, 14, 16, and 19, those of cable –W169 connected to terminals 13, 15, 18, 19, and 20.

4

Power cable –W11 with sealing end; The sealing end and the metallic armour, if any, connected to a protective earth bar.

5

Power cable –W13 with a neutral conductor.

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

NOTE The neutral conductor may be designed as the other three conductors or as a concentric conductor.

6

Coaxial cable –W15, provided with a coaxial plug –W15X1 connected to a corresponding socket –X3 in an assembly.

7

Cable –W16 consisting of four conductors, one of which is an optical fibre, provided with a plug –W16X1, connected to a corresponding socket –X1 in an assembly.

Figure 4 — Examples of representations of connections using various types of cables

11

© BSI 02-1999


Not for Resale

EN 61082-3:1994

Connection Type

Designation

31 32 33 34 35 36 37 38 39 40 – – LINK 41 42 43 44 45 46 47 48 LINK 49 50 51

Connection points Instruction

TWIST 1 TWIST 1 TWIST 2 TWIST 2

Unit

–K11 –K11 –K11 –K11 –K11 –K11 –K12 –K12 –K12 –K12 –K13 –K13 –K13 –K14 –K14 –K14 –K15 –K15 –K15 –K15 –K15 –K16 –K16 –K16 –K16

Term.

:1 :2 :3 :4 :5 :6 :3 :4 :5 :6 :1 :2 :3 :A :B :C :1 :2 :3 :4 :6 :12 :1 :2 :3

Rem.

34 40

35

48

Unit

–K12 –K12 –K15 –K12 –K14 –X1 –X1 –X1 –X1 –K13 –V1 –V1 –K13 –X1 –X1 –K16 –X1 –X1 –X1 –X1 –K16 –K16 –X1 –X1 –X1

Term.

:1 :2 :5 :5 :C :1 :2 :3 :4 :1 :C :A :4 :5 :6 :11 :7 :8 :9 :10 :12 :13 :11 :12 :13

Rem.

39 43

–V1

LINK

Figure 5 — Example of a connection-oriented unit connection table. See subclause 3.3 for an explanation of the notation

Figure 6 — Example of a unit connection diagram in matrix form for a sub-rack

12

© BSI 02-1999

--`,,```,,,,````-`-`,,`,,`,`,,`---


Not for Resale

EN 61082-3:1994

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

Figure 7 — Example of a unit connection diagram for a sub-rack

13

© BSI 02-1999


Not for Resale

EN 61082-3:1994

Section 4. Interconnection diagrams and tables 4.1 General Interconnection diagrams and tables shall provide the information required about the connections among different constructional units of equipment or installations. Information about the internal connections in the units need not be included, but appropriate references (for example reference to unit connection diagram or table or references to internal components by means of their item designations), may be provided. 4.2 Layout of diagrams All devices and connections should be shown as though they were all in one plane.

Figure 9 shows an example of an interconnection diagram using partly single-line representation for the same equipment as depicted in Figure 8. Figure 10 shows an example of an interconnection diagram in which the prefabricated cable –W3 is terminated by means of a connector at each end. Figure 11 shows an example of an interconnection diagram for the cable shown in Figure 10. Single-line representation has been used and the information on the individual connections has been supplemented with information on the kind of current and voltage. Figure 12 shows an example of a connection-oriented interconnection table for the same installation as shown in Figure 8.

4.3 Examples Figure 8 shows an example of an interconnection diagram using multi-line representation. The information for the cable end of –W109 has been supplemented with an item designation for the remote end.

Figure 8 — Example of an interconnection diagram using multi-line representation

© BSI 02-1999

14


Not for Resale

` , , ` , ` , , ` , , ` ` ` ` ` ` , , , , ` ` ` , , ` -

EN 61082-3:1994

Figure 9 — Example of an interconnection diagram using partly single-line representation

` , , ` , ` , , ` , , ` ` ` ` ` ` , , , , ` ` ` , , ` -

Figure 10 — Example of an interconnection diagram with cable end connectors

Figure 11 — Example of an interconnection diagram in single-line representation, showing cable connectors

15

© BSI 02-1999


Not for Resale

EN 61082-3:1994

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

Cable type

HO5VV–U3×1.5

Cable Core No.

Connection points Item

–W107 .1 .2 .3

+A–X1

HO5VV–U2×1.5

–W108 .1 .2

+B–X1

HO5VV–U31.5

–W109 .1 .2

+A–X1

Term.

1 2 3

Rem.

Item

+B–X1 –W109.1

1 3

–W107.3 –W107.2

3 4

–W107.3

Remark

+C–X1

Term.

2 3 1

Rem.

–W108.2 –W108.1

1 2

+D

Aux. volt. supply AC 230 V

Figure 12 — Example of a connection-oriented interconnection table

© BSI 02-1999

16


Not for Resale

EN 61082-3:1994

Section 5. Terminal connection diagrams and tables 5.1 General A terminal connection diagram or table shall provide the information required to make the external connections to a single constructional unit or equipment. A set of terminal connection diagrams or tables providing information about the connections to a corresponding set of units shall contain the same information in the same form as an interconnection diagram or table for the connections among the same units, i.e. the same rules apply.

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

5.2 Examples Figure 13 shows two terminal connection diagrams, one for constructional unit +A4 and the other for constructional unit +B5. Each cable end is designated by its item designation and each core by its core number. Spare terminals with or without connections are indicated by the letters RES (reserved).

Figure 14 shows the same two terminal connection diagrams, supplemented with terminal designations of the remote end. Figure 15 shows two connection-oriented terminal connection tables with terminal designations for the remote end, based on Figure 14. The symbol dash (–) indicates that there is no connection. Spare cores, whether or not connected to terminals, are denoted by the letters RES. Figure 16 shows a terminal-oriented terminal connection table, based on the terminal diagram for unit +A4 in Figure 13. Figure 17 shows an example of a terminal connection table of grid type, based on Figure 13. The number of cores of a cable is noted in a column, adjacent to the cable number and the spare cores in the last column on the same line.

Figure 13 — Example of two terminal connection diagrams

17

© BSI 02-1999


Not for Resale

EN 61082-3:1994

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

Figure 14 — Example of two terminal connection diagrams with remote end designations

Cable No. Core No.

–Wt136

–W137

PE 1 2 3 4 5

Terminal

–X1:PE –X1:11 –X1:17 –X1:18 –X1:19 –X1:20

PE –X1:PE –X1:12 1 –X1:13 2 –X1:14 3 –X1:15 4 –X1:16 5 – 6

Remote end

+B4 –X1:PE –X1:33 –X1:34 –X1:35 –X1:36 –X1:37

Rem.

Cable No.

–W 137

RES

Core No.

PE 1 2 3 4 5 6

Terminal

–X1:PE –X1:26 –X1:27 –X1:28 –X1:29 – –

Remote end

Rem.

+A4 –X1:PE –X1:12 –X1:13 –X1:14 –X1:15 –X1:16 RES – RES

+B5 –X1:PE –X1:26 –X1:27 –X1:28 –X1:29 – RES – RES +A4 234567

+B5 234568

Figure 15 — Example of two connection-oriented terminal connection tables with remote end designations

© BSI 02-1999

18


Not for Resale

EN 61082-3:1994

` , , ` ` ` , , , , ` ` ` ` ` ` , , ` , , ` , ` , , ` -

Item

Terminal

–X1

:11 :12 :13 :14 :15 :16 :17 :18 :19 :20 :PE :PE RES

Cable

–W136 –W137 –W137 –W137 –W137 –W137 –W136 –W136 –W136 –W136 –W136 –W137 –W137

Core

1 1 2 3 4 5 2 3 4 5 PE PE 6 +A4 345778

Figure 16 — Example of a terminal-oriented terminal connection table

Figure 17 — Example of terminal connection table of grid type with remote end designations

19

© BSI 02-1999


Not for Resale

EN 61082-3:1994

Figure 18 — Example of part of a cable diagram where groups of cables have been represented by single lines

` , , ` , ` , , ` , , ` ` ` ` ` ` , , , , ` ` ` , , ` -

© BSI 02-1999

20


Not for Resale

EN 61082-3:1994

Section 6. Cable diagrams, tables and lists Figure 20 shows an example with three units –A1, –A2, and –A3. Units –A1 and –A2 are provided with socket outlets whereas unit –A3 is provided with non-removable cables –W1 and –W2, each ending with a plug, –X1 and –X2 respectively. Units –A1 and –A2 are interconnected by the screened 5-core cable –W1, provided with plugs –X1 and –X2. Units –A1 and –A3 are interconnected by the 9-core screened cable –W1, which is a part of unit –A3. Figure 21 shows an example of a cable table for the same equipment as that shown in Figure 19.

6.1 General Cable diagrams and tables shall provide all information required for laying the cables among constructional units of equipment or installations. Information about the cable routes shall be included if necessary. Groups of cables may be shown in single-line representation with cable item designations. See Figure 18. 6.2 Examples Figure 19 shows an example of a cable diagram, based on Figure 8.

` , , ` , ` , , ` , , ` ` ` ` ` ` , , , , ` ` ` , , ` -

Figure 19 — Example of a cable diagram

Figure 20 — Example of a cable diagram showing prefabricated cables provided with connectors Cable No.

–W107 –W108 –W109

Cable type

HO5VV–U3×1.5 HO5VV–U2×1.5 HO5VV–U2×1.5

End points

+A +B +A

+B +C +D

Remarks

Aux. volt. supply AC 230V

Figure 21 — Example of a cable table

21

© BSI 02-1999


Not for Resale

EN 61082-3:1994

Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. NOTE When the international publication has been modified by CENELEC common modifications, indicated by (mod.), the relevant EN/HD applies. IEC publication

Date

Title

EN/HD

Date

445

1988

EN 60445

1990

446 617-3

1989a 1983

Identification of equipment terminals and of terminations of certain designated conductors, including general rules for an alphanumeric system Identification of conductors by colours or numerals

— —

— —

750 757 1082-1

1983 1983 1991

— HD 457 S1 EN 61082-1

— 1985 1993

EN 61082-2

1994

Graphical symbols for diagrams Part 3: Conductors and connecting devices Item designation in electrotechnology Code for designation of colour Preparation of documents used in electrotechnology

Part 1: General requirements (corrigendum November 1993) 1082-2

1993

Preparation of documents used in electrotechnology Part 2: Function-oriented diagrams

a IEC 446:1973 is harmonized as HD 324 S1:1977.

22

--`,,```,,,,````-`-`,,`,,`,`,,`---


© BSI 02-1999 Not for Resale

BS EN 61082-3:1994 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the General Electrotechnical Standards Policy Committee (GEL/-) to Technical Committee GEL/3 upon which the following bodies were represented:

British Photographic Association Consumer Policy Committee of BSI EEA (the Association of Electronics, Telecommunications and Business Equipment Industries) GAMBICA (BEAMA Ltd.) Transmission and Distribution Association (BEAMA Ltd.) National annex NB (informative) Cross-references Publication referred to

Corresponding British Standard

IEC 445:1988

BS 5559:1991 Specification for identification of equipment terminals and of

IEC 617-3:1983

IEC 1082-1:1991 IEC 1082-2:1993

© BSI 02-1999

terminations of certain designated conductors, including general rules for an alphanumeric system BS 3939 Graphical symbols for electrical power, telecommunications and electronics diagrams Part 3:1985 Conductors and connecting devices BS EN 61082 Preparation of documents used in electrotechnology BS EN 61082-1:1993 General requirments BS EN 61082-2:1994 Function-oriented diagrams

--`,,```,,,,````-`-`,,`,,`,`,,`---


Not for Resale

BSI 389 Chiswick High Road London W4 4AL

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

BSI Ð British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions

British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards

Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards

BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright

Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means ± electronic, photocopying, recording or otherwise ± without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.

--`,,```,,,,````-`-`,,`,,`,`,,`---


Not for Resale

IEC-61082_3.pdf

Recommend Documents