Fuji Frontier 330-340-350-370-390 - Di Print-data Writing Service Software Ver.5.0 First Edition Rulit Net 158097

INSTRUCTION MANUAL < Optional Software >

FRONTIER

330/340/350/370/390 DI PRINT/DATA WRITING SERVICE SOFTWARE Ver.5.0 Basic Operating Instructions

DI Print/Data Writing Service Software Ver.5.0 (FRONTIER 330/340 System Disk Ver.2.0 or later) (FRONTIER 350/370/390 System Disk Ver.6.6 or later)

First Edition PP3-B1001E

INTRODUCTION • This instruction manual explains the procedures for operating and maintaining the DI Print and Data Writing Service for Fujifilm Digital Minilab FRONTIER Series as well as precautions for its use. • To ensure proper use and optimum performance of the FUJIFILM DIGITAL IMAGING PRINT SERVICE system, read this manual thoroughly. • This manual should be kept in a fixed place near the machine so that it can be referred to at any time a point needs to be clarified. Specifications are subject to change without notification. Zip™, Jaz™ are trademarks of Iomega Corporation. SmartMedia™ is a trademark of Toshiba Corporation. CompactFlash™ is a trademark of SanDisk Corporation. Microdrive™ is a trademark of IBM Corporation. Memory Stick™ is a trademark of Sony Corporation. SD Memory Card™ is a trademark of Toshiba Corporation, Matsushita Electric Industrial Co., Ltd and SanDisk Coporation. Microsoft®, Windows®, Windows® NT and Windows® 2000 are registered trademarks of Microsoft Corporation. Pentium® is a registered trademark of Intel Corporation. Adobe®, Photoshop® are registered trademarks of Adobe Systems Incorporated. ScanMaker™ is a trademark of Microtek Corporation. All other brand names or trademarks are the property of their respective owners.

NOTICE 1. Electro-optical-mechanical reproduction of this manual is strictly forbidden. 2. Product innovations may result in specification changes without prior notice. UNITED STATES OF AMERICA (FCC) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CANADA (ICES) This class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la class A respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada.

CONTENTS 1

2

Features ......................................................................................................................

6

1.1 1.2

New Features ........................................................................................................ Backup Order Function Installation/Setup .............................................................

6 8

Operational Safety and Use Conditions .........................................................

9

2.1

3

Starting Up Imaging Controller .............................................................................. 18 Shutting Down Imaging Controller ......................................................................... 23

DSC Printing Service.............................................................................................. 26 4.1 4.2 4.3 4.4 4.5

5

9 9 10 11 13 14 15 16 17

Starting Up and Shutting Down ......................................................................... 18 3.1 3.2

4

Media Handling...................................................................................................... 2.1.1 PC Card .................................................................................................... 2.1.2 Smart Media ............................................................................................. 2.1.3 Compact Flash.......................................................................................... 2.1.4 Memory Stick (SD Memory Card) ............................................................. 2.1.5 MO ............................................................................................................ 2.1.6 Zip............................................................................................................. 2.1.7 CD-R ......................................................................................................... 2.1.8 FD .............................................................................................................

Digital Camera Print Service Screen ..................................................................... DSC Printing Procedures....................................................................................... View and Order Screen ......................................................................................... Printing in FRONTIER ........................................................................................... Procedures for Changing Settings......................................................................... 4.5.1 Changing of Media Drive Setting .............................................................. 4.5.2 Changing of Output Device Setting .......................................................... 4.5.3 Master Balance Adjustment...................................................................... 4.5.4 DSC Setting ..............................................................................................

26 28 34 36 40 40 42 44 45

Media Printing Service .......................................................................................... 47 5.1

5.2

Media Printing Service (without order file) ............................................................. 5.1.1 Media Print Service Screen ...................................................................... 5.1.2 Media Printing (without order file) Procedures.......................................... Media Pinting Service (with order file) ................................................................... 5.2.1 COS Print Service Screen ........................................................................ 5.2.2 COS Printing Procedures ......................................................................... 5.2.3 DPOF Print Service Screen ...................................................................... 5.2.4 DPOF Printing Procedures .......................................................................

47 47 49 54 54 56 60 61

3

5.3

6

65 65 65 65

CD Printing Service ................................................................................................ 67 6.1 6.2 6.3

CD Print Service Screen........................................................................................ CD Printing Procedures ......................................................................................... Procedures for Changing Settings......................................................................... 6.3.1 Changing of Media Drive Setting .............................................................. 6.3.2 Changing of Output Device Setting .......................................................... 6.3.3 Master Balance Adjustment......................................................................

67 69 75 75 75 75

7

Backup Order Function ......................................................................................... 77

8

Print-to-Print .............................................................................................................. 83 8.1 8.2 8.3

9

Print-to-Print Service Screen ................................................................................. Print-to-Print Procedures ....................................................................................... Procedures for Changing Settings......................................................................... 8.3.1 Changing of Media Drive Setting .............................................................. 8.3.2 Changing of Print-to-Print Setting .............................................................

83 85 90 90 92

CD/Media Writing Service..................................................................................... 94 9.1 9.2

9.3 9.4 9.5

9.6

4

Procedures for Changing Settings......................................................................... 5.3.1 Changing of Media Drive Setting .............................................................. 5.3.2 Changing of Output Device Setting .......................................................... 5.3.3 Master Balance Adjustment......................................................................

Writing Service Main Screen ................................................................................. 94 CD/Media Writing Procedures ............................................................................... 96 9.2.1 Film Digitizing in FRONTIER .................................................................... 96 9.2.2 Order Condition Settings Screen .............................................................. 103 9.2.3 Writing Procedures ................................................................................... 104 9.2.4 Image List Screen for Writing Service ...................................................... 108 Writing from DSC/Media ........................................................................................ 109 Index Print Creation ............................................................................................... 116 Special Operations ................................................................................................ 119 9.5.1 CD-R Copy Procedures ............................................................................ 119 9.5.2 Index Print Creation from CD-R ................................................................ 123 Procedures for Changing Settings......................................................................... 126 9.6.1 Data Writing Administration ...................................................................... 126 9.6.2 Media Drive Setting .................................................................................. 128 9.6.3 Optional Software Setting ......................................................................... 129 9.6.4 Service Type Setting................................................................................. 130 9.6.5 Index Print Size Selection......................................................................... 132

10

Multiple Service ........................................................................................................ 133 10.1 Printing Screen (in use of Multiple Service)........................................................... 133 10.2 Multiple Service Setting ......................................................................................... 134

11

Digital Photo Center ............................................................................................... 138 11.1 Operating Digital Photo Center (DPC) Operation .................................................. 138 11.1.1 Using of LAN Connection ......................................................................... 139 11.1.2 Using of Branch Store Connection ........................................................... 141 11.2 Operating Digital Reorder Service ......................................................................... 143 11.3 Digital Photo Center Settings................................................................................. 147 11.3.1 Drive/Path Setting for DPC ....................................................................... 147 11.3.2 DPC Administrative Settings..................................................................... 149 11.4 Digital Reorder Service Settings............................................................................ 151 11.4.1 Drive/Path Setting for Digital Reorder....................................................... 151 11.4.2 Digital Reorder Service Administrative Settings ....................................... 153 11.4.3 Registering of Digital Reorder Service into Multiple Service .................... 156

12

Operation Screens and Function Key List ..................................................... 157 12.1 12.2 12.3 12.4

13

Printing Service...................................................................................................... 157 Data Writing Service .............................................................................................. 161 Print-to-Print Service.............................................................................................. 163 System................................................................................................................... 164

Index ............................................................................................................................. 165

5

1

Features

1.1 ■

New Features

Image Processing Improvement

The image processing is much improved in the following points. (1) Color/Density correction (2) Tone Reproduction (3) Hyper-tone and Highlight/shadow gradation ■

Easy-to-Installation

The two types of installation mode [Standard] and [Custom] can be selected. In the [Standard] mode, the current status of the Imaging Controller is checked by the program, so you can install the program without a few keyboard entries and by clicking the buttons several times. In the [Custom] mode, you can install it while selecting the installing type to meet your needs. ■

Operation/Function Improvement

(1)Output type selection in the Print-to-Print processing. Scanned image can be processed in the Variety Print [C10] or Hyper-Retouch [C11] as well as the data writing and printing. (2)Screen Display • Displaying of version number in the main screen • Horizontal scroll bar appears printing service screen when the long file name is used in registration. • Hard disk space can be monitored visually in the Server Status screen

(3)Operation Printing [C4] • DSC auto correction ON/OFF settings • Auto correction ON/OFF in each frame can be easily switched by [F10] key. • Unnecessary printing order files deletion

Writing [C5] • Writing-completed order can be stored during from 0 to 999 minutes that is selected in the Administration screen beforehand. It enables you to rewrite the order when it fails. • Status of writing-completed order can be returned to the “Wait” status. • Unnecessary printing order files deletion • [Execution] button is added to the Printing screen, to run the optional application. • Writing speed [Fast] (max. speed) or [Normal] can be selected. • BMP/JPG format output with film-scanning in FRONTIER is newly provided. • DSC date front printing is provided for all Exif image printing including CD-R writing.

6

Others • Number of pixels available in FujiColor CD are increased.

- From 150 M pixels to 200 M pixels in negative - No resize in DSC/Media • Version Checker that lists up the application installed in the Imaging Controller, is provided.

7

1.2

Backup Order Function Installation/Setup

Backup Order Function is the function where you can store temporarily the orders from the external application (Kiosk, etc.), and later you can correct these orders by using the View and Order screen. ■

Added Functions

By installing the Backup Order Function, the following function can be used. Printing [C4] • Re-registration function of printing order • Test Printing in the View and Order screen

Writing [C5] • New services (devices) are added. The following devices are added to the Digital Service Selection list.

Service Name

Functions

FDi CD1 FDi CD2

Three types of FDi CD are added. Additional data such viewer can be written.

FDi CD3 FDi CD with FCD

FUJICOLOR CD with FDi CD(higher- or lower pixels)

Pro CD

In this service the order uses the print size selected in the Print Size setup in film scanning, while the original image size is adopted in the DCS Printing.

• Picture Rotation

The radio buttons selecting the upper side are added to the frames in the Image List screen. To display these radio buttons, add the check mark to [Yes] box in [Picture Rotate] in the Writing Service-Administration screen.

8

2

Operational Safety and Use Conditions

2.1

Media Handling

2.1.1 PC Card Insert the PC card into the card reader (optional) slowly.

1-slot type

EM786

2-slot type

FD063

Remove the PC card from the card reader while pressing the eject button.

1-slot type

IMPORTANT When removing the PC card from the PC card reader, make sure that the access LED is completely gone out. If it is removed while the LED is lighted, the data in the PC card may be corrupted. PC card

EM787

IMPORTANT If the system is turned off or shut down while reading the data, corruption of data may occur. Make sure not to turn off the Imaging Controller or media drives. It is strongly recommended to use the UPS (Uninterruptible Power System).

2-slot type

FD064

9

■ • • • •

Precautions for Use Make sure dust or debris does not collect on the terminal. Do not damage or drop the media. Do not place the media near a heat source. Do not leave the media in the high-temperature, high-humidity place for a long time.

2.1.2 Smart Media Insert the Smart Media into the card adapter (optional) slowly.

EM785

Insert the card adapter into the card reader (optional) slowly.

2-slot type

FD063

Remove the card adapter from the card reader while pressing the eject button.

2-slot type

FD064

IMPORTANT When removing the PC card adapter from the PC card reader, make sure that the access LED is completely gone out. If it is removed while the LED is lighted, the data in the PC card may be corrupted. IMPORTANT Never remove only the Smart Media from the card adapter when the latter is set in the card reader. If it is done so, the data in the Smart Media may be corrupted.

10

IMPORTANT If the system is turned off or shut down while reading the data, corruption of data may occur. Make sure not to turn off the Imaging Controller or media drives. It is strongly recommended to use the UPS (Uninterruptible Power System). ■ • • • •


2.1.3 Compact Flash Insert the Compact Flash into the card adapter (optional) slowly.

EM784


2-slot type

FD063

11


2-slot type

FD064

IMPORTANT When removing the PC card adapter from the PC card reader, make sure that the access LED is completely gone out. If it is removed while the LED is lighted, the data in the PC card may be corrupted. IMPORTANT Never remove only the Compact Flash from the card adapter when the latter is set in the card reader. If it is done so, the data in the Compact Flash may be corrupted. IMPORTANT If the system is turned off or shut down while reading the data, corruption of data may occur. Make sure not to turn off the Imaging Controller or media drives. It is strongly recommended to use the UPS (Uninterruptible Power System).

■ • • • •

12


2.1.4 Memory Stick (SD Memory Card) Insert the Memory Stick (SD Memory Card) into the card adapter (optional) slowly, so that its printed surface comes upside.

IMPORTANT If it is inserted wrongly, the data in it may be corrupted.

PJ007


2-slot type

FD063


2-slot type

FD064

IMPORTANT When removing the PC card adapter from the PC card reader, make sure that the access LED is completely gone out. If it is removed while the LED is lighted, the data in the PC card may be corrupted. IMPORTANT Never remove only the Memory Stick (SD Memory Card) from the card adapter when the latter is set in the card reader. If it is done so, the data in the Memory Stick (SD Memory Card) may be corrupted. IMPORTANT If the system is turned off or shut down while reading the data, corruption of data may occur. Make sure not to turn off the Imaging Controller or media drives. It is strongly recommended to use the UPS (Uninterruptible Power System).

13

Remove the Memory Stick (SD Memory Card) from the card adapter while pressing the eject button.

PJ008

■ • • • •


2.1.5 MO Insert the MO into the MO drive slowly, so that its printed surface comes upside.

MO drive


MO

FD012

Remove the MO from the MO drive by pressing the eject button. NOTE: Please wait until the access LED is extinguished. Normally the MO cannot be removed from the drive until reading of data is completed. FD013

14

IMPORTANT If the system is turned off or shut down while reading the data, corruption of data may occur. Make sure not to turn off the Imaging Controller or media drives. It is strongly recommended to use the UPS (Uninterruptible Power System). ■ • • • •

Precautions for Use Never open the shutter to touch the disk. If the shutter is open, close it before inserting it into the drive. Do not damage or drop the media. Do not place the media near a heat source. Do not leave the media in the high-temperature, high-humidity place for a long time.

2.1.6 Zip Insert the Zip into the Zip drive slowly, so that its printed surface comes upside.

Zip drive


Zip

FD010

Remove the Zip from the Zip drive by pressing the eject button. NOTE: Normally the Zip cannot be removed from the drive until reading of data is completed.

FD011


15

■ • • • •


2.1.7 CD-R Press the eject button, set the CD onto the tray, and then press the eject button again, so the CD is properly set up.

IMPORTANT If it is set wrongly, the data in it may be corrupted. FD043

Press the eject button, remove the CD from the tray, and then press the eject button again. NOTE: Normally the CD cannot be removed from the drive until reading of data is completed.

FD044


■ Precautions for Use • Do not place the media near a heat source. • Do not leave the media in the high-temperature, high-humidity place for a long time. • Make sure dust or debris does not collect on the reading surface of the CD. • To remove any dust or debris adhering to the reading surface, use a soft cloth to wipe it off, starting from the center to and moving the outside. • To wipe off dust or debris, never use any solvent such as benzine, thinner, anti-static cleaner or LP cleaner.

16

2.1.8 FD Insert the FD into the FD drive slowly.

IMPORTANT If it is inserted wrongly, the media or data may be destroyed.

FD045

Remove the FD from the FD drive by pressing the eject button.

IMPORTANT When removing the FD from the FD drive, make sure that the access LED is completely gone out. If it is removed while the LED is lighted, the data in the FD may be corrupted. FD046

IMPORTANT If the system is turned off or shut down while reading the data, corruption of data may occur. Make sure not to turn off the Imaging Controller or media drives. It is strongly recommended to use the UPS(Uninterruptible Power System). ■ • • • •


17

3 3.1

Starting Up and Shutting Down Starting Up Imaging Controller

Start the Imaging Controller as follows: Turn ON the media device (PC card reader, Zip, MO, CD-R drives, etc.).

FD034

Turn ON the flatbed scanner.

FD257

Turn ON the monitor.

FD036

Turn ON the Imaging Controller (PC).

FD032

18

The Print Service screen appears.

19

■ Printing Screen

After starting the Imaging Controller, the following Print Screen appears. Here, you can register order(s) for printing with the image data file(s).

1 2

3 4

5

6

7

8 9

10 11

12

13 19

17 18

20 14 No.

15

Item

16 Description

1

Order Number

Shows the order number. This is incremented each time an order is registered.

2

[Printing] icon

Displays this screen.

3

Print Q’ty

Shows the print number when “Auto.” is selected. The print number cannot be specified for each image.

4

[Writing] icon

Displays the CD writing [CS] screen. (See “9.1 Writing Service Main Screen” on page 94.

5

Print Size

Shows the print size when “Auto.” is selected. The print size cannot be specified for each image.

6

[System] icon

Displays the System screen, where you can monitor the status of spool-free space, or the selected printing devices.

7

Automatic

Press this icon to select one of the automatic transaction types previously selected in printing administration. This function can be used only when printing all images in the media at a time.

8

Admin.

Click this icon to do the printing administration settings for the printing screen.

9

[EXIT] icon

Exits the DI Print/Data Writing Service [C4/C5], or shuts down the Imaging Controller while pressing the [Shift] Key.

10

Help

Displays the Help screen.

20

No.

Item

Description

11

OUTPUT

Available output devices set in the printing administration screen. At the time of starting an order registration, click one of these output devices. Selected output devices are indicated with the white back-ground. • Click [ | ] area in the slider bar to display another 4 buttons in the reverse field. Up to 8 output devices can be registered in the [OUTPUT] field.

12

INPUT

Available input media or devices that have been set in the printing administration screen. At the time of starting an order registration, click one of these input media or devices. • Click [ | ] area in the slider bar to display another 9 buttons in the reverse field. Up to 18 input devices can be registered. • Click (one of the media buttons) to automatically read the image files in the media, and then to display the Order Registration screen of each service appropriate to the image file format. • Click [PtoP] button to display the Print to Print screen, in which you can print image data that has been created by scanning a photo with the flatbed scanner. • Click [DPC] or [DPC-M] button to register the order(s) from the Digital Photo Center print service.

13

Express

Click this button to change the print status from [Wait] to [Express]. An order with [Express] status has the highest priority for printing, so it is processed first.

14

Reprint

Reprint the order that has already been completed or the order with Hold status. Select the order to be reprinted, and then click this button.

15

Hold

Select a wait order and then click this button to hold back printing. To print the order, select the Hold order, and then click the Reprint button.

16

Recover

When there is an error image in an order, click this button to recover it as Wait order. The order is recovered while the error image is skipped.

17

Info.

Shows the detailed information for each order.

18

Trash

Deletes an order already printed or a specific order. Select the order to be deleted, and then click this button.

21

No.

Item

Description

19

Order Registration Status Display

• [Order Number]: Registered Order number. • [Input]: [Print Service], [Index Print] , [Large Index Print] , [DPC Print] or [Print-toPrint] appears according to input type. • [Output]: Type of output device. • [Image Q ty]: Number of images in an order. • [Print Q ty]: Number of prints in an order. • [Status]: [Wait], [Done], [Express], [Hold], [Printing], [Converting] or [Error] appears according to the status. • [Service Type]: [DSC Print], [Media Print], [CD-R Reprint], [DPOF] or [Print] appears according to the image file format. • [Paper Width]: Paper width for printing. • [Index]: [Yes] shows Index print registered through the Print Service. • [Create Date]: The order created data.

20

Version Display

Shows the version number of installed apllication.

22

3.2

Shutting Down Imaging Controller

Shut down the Imaging controller. Click the [Exit] icon on the DI changer.

The Confirmation dialog appears. Click the [OK] button.

IMPORTANT Do not shut down the Imaging Controller while orders are being converted. Click.

Operation returns to the Desktop of Windows NT/Windows 2000. To shut down the computer, click the [Exit] button while pressing the [Shift] button.

23

[Windows NT]

Select [Shut Down] from the [Start] menu on the bottom of the desktop.

[Windows 2000]

[Windows NT]

[Windows 2000]

24

In case of Windows NT, Select the [Shut down the computer?] and click the [Yes] button.

In case of Windows 2000, Select [Shut down] and click the [OK] button.

Turn OFF the media units (PC card reader, CDR, Zip, MO drives, flatbed scanner, etc.)

FD034

Turn OFF the flatbed scanner.

FD257

Turn OFF the monitor.

FD036

Turn OFF the Imaging Controller.

FD032

25

4

DSC Printing Service

4.1

Digital Camera Print Service Screen

In the Digital Camera Print Service screen, register the image files containing no order file, and then do printing from digital cameras. This screen processes the digital still camera images with the image format of (Exif-JPG, Exif-TIFF and CAM).

1

2 3

4 5

6

7

21 8 20 19

9

18

10 11

17

12 13 22

No.

26

16

Item

15

14

Description

1

Order Number


2

Output

Displays the currently selected output device.

3

Frame No.

In the case of FUJICOLOR CD or DCF format, either all frames or each frame can be selected.

4

Print Q’ty

Enter the number of prints in this box. If you want to create the index print only, enter “0” in this box, and then specify number of index or large index prints in [12 Index/Large Index Print Setting].

5

Print Size

Select print size. This information is registered to the system at the time of “Preoperational check” in FRONTIER.

6

Resize

Select resize type in printing. Fill-in: Fill the entire print size with the selected image; the image may be cut off either horizontally or vertically. Fit-in: Fit the image within the print size as well as possible without cutting off any of the image. No Resize: Print the image data without any resizing.

7

Help


No.

Item

Description

8

Print Q’ty Display

The number of prints in each service that was selected in the [Order Specification Column].

9

Print Q’ty buttons

Up to 9 of the number of prints can be specified by clicking one of these numeral buttons. The specified number appears in the [Order Specification Column].

10

Order Regist.

Register the image files that are listed in the [Order Specification Column].

11

View and Order

The 6-frame View and Order screen lets you review all the thumbnail images in the [Order Specification Column] before starting printing. The color can be automatically adjusted (digital still camera format) or manually. (See “4.3 View and Order Screen” on page 34.)

12

Index/Large Index Print Setting/ DSC Date

Select [Yes] or [No] to print index/large index prints and specify the number of prints. To add the data on the front print, check the [DSC data] box. In case of creating index print only: If you create the index print only, spcify number of index or large index prints, while entering “0” in [Print Q’ty] box.

13

Order Reset

Resets the images files listed and selected in the [Order Specification Column].

14

Cancel

Cancels the registration of the image files listed in the [Order Specification Column], and control returns to the printing screen.

15

Set

Click this button to move the selected image files to the [Order Specification Column].

16

Select All

Click this button to select all images in the [File Name] column.

17

Order Specification [Image file name]: Column Names of registered image files [Directory]: Name of the directory containing the image files [Image No.]: Serial number of registered images [Print Q’ty]: Number of prints [Service type]: [DSC Print] appears according to the image file format. [Size]: Print size of registered image files [Resize]: [Fill-in], [Fit-in] or [No resize] appears according to the selected resize type.

18

Search

To know where the image files are located, use this button to display all images in the media.

19

File Name

Click the files to be printed.

20

Directory

To display the image files, click the folder in storage media.

21

Directory No.

In the case of FUJICOLOR CD or DCF format, either all directories or an individual directory can be selected.

22

Horizontal Scroll Bar

If the image file name is long, the scroll bar appears.

27

4.2

DSC Printing Procedures

Register the order for images in the DSC media, and then print them in FRONTIER. Set the media in the drive.

FD121

In the [OUTPUT] field, select the FRONTIER device. Select the FRONTIER device.

Click the icon of the media you inserted.

In the [INPUT] field, click the icon of the media you inserted.

28

Select the folder.

In the DSC Print Service screen, select the folder in which the images are stored.

Select the images.

Select the images to be printed. To register all images, click the [Select All] button.

Select the print size.


IMPORTANT You must select the print size for each order.

29

Specify if or not the index/large index is outputted, and its output size, and then if the DSC date is printed on the print or not. If you want to create the index print only, specify number of index or large index prints, while entering “0” in [Print Q’ty] box.

Specify if or not the index/large index is outputted, size, and if DSC Date is printed or not.

Select the resizing specification. (See “2.2(2) Resize” in “Instruction Manual (Service Specification)”.)

Select the resizing option.

30

Click the [Set] button. The image files are listed up in the [Order Specification Column].

Click the [Set] button.

Click the [Order Regist.] button.

To monitor the images

Click the [View and Order] button. (See “4.3 View and Order Screen” on page 34.)

31

The ”Confirmation” dialog appears.

Remove the media from the drive.

FD124

Click the [OK] button.

Click.

Registering of order is completed.

32

Print the registered images in FRONTIER. (See “4.4 Printing in FRONTIER” on page 36.)

(FRONTIER 350/370/390)

(FRONTIER 330/340)

33

4.3

View and Order Screen

The “View and Order” screen lets you review all the images in a customer’s order before printing them. To correct an image, use the arrow keys to select it and then click the buttons next to the CMYD boxes. Press [ESC] key to exit this screen and return to Order Registration screen.

2

1 3

4 No.

34

5

6

Item

7

8

Description

1

Print Q’ty Setting

Changes the number of prints.

2

File Name

Shows the image file name (up to 8 characters).

3

CMYD Setting

C: Cyan M: Magenta Y: Yellow D:Density (Range: –15 to +15)

4

All/Order

Registers all images in an order including the 6 images that are currently displayed with one click.

5

Page/Order

Registers only the 6 images that are currently displayed. Upon completion of the registration, the next 6 images are displayed if there are more than 6 images in an order.

6

Sharpness

In the case of the Media Print Images, the sharpness correction can be done. It is recommended to use this correction and reprint such as a blurred large-size image. The result of the function is not shown on the displayed image.

7

Scene Correction

In the case of the DSC Images, the scene correction can be done with one click. [Standard], [Cloudy], [Back-Lit] or [Close shot with Flash] can be selected as correction type.

8

Auto Correction

The auto correction is automatically done in the DSC images. [No] to correction can also be selected such as in the case of an image with template. It is strongly recommended to select [Yes] in most cases.It can be also turned on by pressing [F10] key after selecting frames.

■ About the [HOLD] in the View and Order Screen

In the “View and Order” screen, the color and density (CMYD) correction data applied to one frame can be held fixed and also applied to the subsequent frames in the order. Select a frame and perform CMYD corrections, and then press [F9] key.

The same correction data are applied to the subsequent frames and these setting data are changed from black to green. To cancel the settings, select the first frame with green setting data, and then press [F9] key.

Same correction values are applied.

35

4.4

Printing in FRONTIER

■ FRONTIER 350/370/390

In the “Main Menu” screen, select [2 Print], click the [OK] button.

Select [Printer Op.] - [Switch Magazine (1)] [Upper] or [Lower], or [Auto] to select the appropriate magazine automatically.

Select.

Select [Print Mode Select (6)] - [Digital Image Import (sRGB)]

Select.

“Reading service name list” message appears.

36

In the “Input Select” screen, select [Print Service] or other service and click [OK].

The order information appears in the [Next Print] column and printing starts.

The information of completed order appears in the [Done] column. Click [End].

Click.

37

Control returns to the “Printing” screen.

38

■ FRONTIER 330/340 Click.

In the “Main Menu” screen, click the [Print/ Export] button.

In the “Order Information” screen, click the [Printing from Imaging Controller] button.

Click.

In the “Color Space Selection” dialog, select the desired color space, and then click the [OK] button.

Printing is started.

39

4.5

Procedures for Changing Settings

4.5.1 Changing of Media Drive Setting Change the media icon that appears in the [INPUT] field in the “Printing” screen. Click.

In the “Printing” screen, click the [Admin.] button.

Enter “DI”.

In the “Password” dialog, enter “DI”, and then click the [OK] button.

Click.

In the “Print Service - Administration” screen, click the [Media Drive] button.

Click the [Media Drive] button.

40

In the “Media Drive Setting” screen, select the icon, name, and drive for the desired media drive.

Select icon, name and device for media.

IMPORTANT Do not allocate the A, C, and D drives, because the system already uses these drives for FD and HD. Click the [OK] button.

Click.

41

4.5.2 Changing of Output Device Setting Change the device name for FRONTIER. In the “Print Service - Administration” screen, click the [Output Device] button.

Click the [Output Device] button.

In the “Output Device Setting” screen, select the icon, icon name and select the output device in the list. Select icon, icon name and output device.

42

Select print size for each service.

Click the [Print Size] button in the selected item, and in the “Print Size Setting” dialog, select the size for each service, then click the [OK] button.

Click.

In the “Output Device Setting” screen, click the [OK] button.

Click.

43

4.5.3 Master Balance Adjustment Change the master balance for DSC Print. In the “Print Service - Administration” screen, click the [Master Balance] button.

Click the [Master Balance] button.

In the “Master Balance” screen, change C, M, Y and D values in the [DSC Print] field. Change C, M, Y and D for DSC Print.

In the “Master Balance” screen, click the [OK] button.

Click.

44

4.5.4 DSC Setting ■ DSC image auto correction seting

Color Intensity/Gradation Adjustment/Hyper Tone/Sharpness can be set for the DSC image auto correction function.

(1) Color Intensity This function allows you to change chroma (vividness) without affecting skin colors. When the setting is shifted toward the plus direction, garment patterns or landscapes become more vivid and distinct.

(2) Gradation Adjustment Gradation (contrast) can be changed without changing chroma. Two steps of “Hard” settings and three steps of “Soft” setting are available. For the picture such as a portrait shot by a high-end digital still camera, “Soft1” or “Soft2” are appropriate for minimizing washing-out of highlights and flat shadows.

45

(3) Hyper Tone With this function highlight and shadow areas are dodged automatically. Frontier uses this technology for printing with film.

*Mode1 : Print quality is improved while keeping print capability as far as possible by switching Hyper Tone and Hyper Tone Light automatically. (Image quality has priority.) Normally this mode is used. *Mode2 : Hyper Tone Light is applied to all images. (Processing speed has priority.) If the processing speed of the existing Imaging Controller is relatively slow, print capability is improved compared to other modes. If Hyper Tone is strongly applied to a scene, the sharpness level of the scene may be slightly lowered. *Mode3 : Hyper Tone is applied to all images. If the processing speed of the existing Imaging Controller is relatively slow, print capability may be reduced. (4) Sharpness USM or Hyper Sharpness can be selected.

*USM : Normally this setting is used. *Hyper Sharpness : This function is used if an underexposed image has conspicuous noises. Noises in the smooth part such as skin are minimized, but the sharpess level may be slightly lowered.

46

5

Media Printing Service

5.1

Media Printing Service (without order file)

5.1.1 Media Print Service Screen In the Digital Camera Print Service screen, register the image files containing no order file, and then do printing from digital cameras. This screen processes the digital image files (except digital still camera images), that were created or manipulated by image-processing software. [BMP(Windows24 bit only), PICT, GIF, JPG, TIFF and FPX]

1

2

3

4

5

6

21

7

8

20 19

9

18

10 11 16

17

12 13 14 22 16 No.

Item

15 Description

1

Order Number


2

Output


3

Frame No.


4

Print Q’ty

Enter the number of prints in this box.

5

Print Size


6

Resize


7

Help


8



47

No.

Item

Description

9



10

Order Regist.


11

View and Order


12

Index/Large Index Print Setting

Select [Yes] or [No] to print index/large index prints and specify the number of prints.

13

Order Reset


14

Cancel


15

Set


16

Select All

Click this button to select all images in the “File Name” column.

17

Order Specification [Image file name]: Column Names of registered image files [Directory]: Name of the directory containing the image files [Image No.]: Serial number of registered images [Print Q’ty]: Number of prints [Service type]: [Media Print] appears according to the image file format. [Size]: Print size of registered image files [Resize]: [Fill-in], [Fit-in] or [No resize] appears according to the selected resize type.

18

Search


19

File Name


20

Directory


21

Directory No.


22


If the image file name is long,the scroll bar appears.

48

5.1.2 Media Printing (without order file) Procedures Register the order for images that were created or processed by an imaging software, and then print them in FRONTIER. Set the media in the drive.

C45015

In the [OUTPUT] field, select the FRONTIER device.

Select the FRONTIER device.



49

Select the images.





Specify if or not the index/large index is outputted, and its output size. DSC date printing is not available. If you create the index print only, specify number of index or large index prints, while entering “0” in [Print Q’ty] box.

Specify if or not the index/large index is outputted, size.

50







51


The “Confirmation” dialog appears.


C45016


Click.

52



(FRONTIER 350/370/390)

(FRONTIER 330/340)

53

5.2

Media Pinting Service (with order file)

Print the images with the order file. These images are automatically registered by the order file created in the specified software (COS) or digital camera function (DPOF).

5.2.1 COS Print Service Screen In the COS order created by the specified order software, the registration is automatically performed according to the (COS file). (Files are automatically recognized.)

2 1 3 4 5 6 7

8 9 No. 1

54

Item

Description

Order Specification [Image file name]: Column Names of registered image files. [Directory]: Name of the directory containing the image files. [Image No.]: Serial number of registered images. [Print Q’ty]: Number of prints [Service type]: [Media Print” appears according to the image file format. [Size]: Print size of registered image files. To change the number of prints, double-click the file name itself in the list, and then change it in the following dialog.

No.

Item

Description

2



3

Order File Info.

Indicate the Customer information according to order file information.

4

Free Order

Displays the normal Order Selection screen, where you can perform the order registration without order file.

5

Order Regist.

Register the image files that are listed in the [Order Selection Column].

6

View and Order

The 6-frame View and Order screen lets you review all the thumbnail images in the [Order Specification Column] before starting printing. The color can be adjusted automatically(digital still camera format) or manually. (See “4.3 View and Order Screen” on page 34.)

7


Not used in Media Print Service(with Order file)

8

Order Reset

Resets the images files listed and selected in the [Order Selection Column].

9

Cancel

Cancels the registration of the images files listed in the [Order Selection Column], and control returns to the “Printing” screen.

55

5.2.2 COS Printing Procedures Register the images created as COS order, and then print them in FRONTIER. Set the media in the drive.

C45015





56

In the “COS Print Service” screen, check that the image files are listed up in the [Order Selection Column].


Click.



C45018

57


Click.



(FRONTIER 350/370/390)

58

(FRONTIER 330/340)

■ To cancel the COS Print Service screen

You can perform regular DSC printing by canceling the “COS Print Service” screen. Click the [Free Order] button.

Click.

The normal “DSC Print Service” screen appears. There, you can process the images without order file.

59

5.2.3 DPOF Print Service Screen In the order specified by the digital camera’s DPOF, the registration is automatically performed according to the (DPOF). (Files are automatically recognized).

1

3

2 4 5 6 7

8

No.

60

Item

Description

1

DPOF Icon

In the case of the DPOF order, this icon appears.

2

Order Selection Column

[Image file name]: Image file names registered in the DPOF order file. [Print Q’ty]: Number of prints registered in the DPOF order file. [Service type]: Service type registered in the DPOF order file. [Front printing]: Front printing registered in the DPOF order file. [Yes] appears only when it is specified. [Cropping]: Cropping registered in the DPOF order file. [Yes] appears only when it is specified. [Index]: Index Print registered in the DPOF order file. [Yes] appears only when it is specified.

3


The number of prints in each service that was selected in the Order Specification column.

4

DPOF Cancel

In the case of the DPOF order, this button appears. To cancel the DPOF order information, click this button to cancel it and to display the normal Order Selection screen, where you can perform the order registration without order file.

5

Order Regist.

Register the image files that are listed in the Order Specification column.

6

View and Order

The 6-frame View and Order screen lets you review all the thumbnail images in the Order Specification column before starting printing. The color can be adjusted automatically(digital still camera format) or manually. (See “4.3 View and Order Screen” on page 34.)

No.

Item

Description

7


(Not used in DPOF service) In the case of the DPOF order, the index print is automatically created according to the order file.

8

Cancel

Cancels the registration of the images files listed in the [Order Specification Column], and control returns to the “Printing” screen.

5.2.4 DPOF Printing Procedures Register the images created as DPOF digital camera, and then print them in FRONTIER. Set the media in the drive.

FD121



61



Click the image files.

In the “DPOF Print Service” screen, check that the image files are listed up in the [Order Selection Column].



62



FD124


Click.


63


(FRONTIER 350/370/390)

(FRONTIER 330/340)

■ To cancel the “DPOF Print Service” screen

You can perform regular DSC printing by canceling the “DPOF Print Service” screen. Click the [DPOF Cancel] button.

Click the [DPOF Cancel] button.

The normal “DSC Print Service” screen appears. There, you can process the images without order file.

64

5.3


5.3.1 Changing of Media Drive Setting Change the media icon that appears in the [INPUT] field in the “Printing” screen.(See “4.5.1 Changing of Media Drive Setting” on page 40.)

5.3.2 Changing of Output Device Setting Change the device name for FRONTIER. (See “4.5.2 Changing of Output Device Setting” on page 42.)

5.3.3 Master Balance Adjustment Change the master balance for Media Print. In the “Print Service - Administration” screen, click the [Master Balance] button.


In the “Master Balance” screen, change C, M, Y and D values in the [Media Print] field.

Change C, M, Y and D in the [Media Print] field.

65


Click.

66

6

CD Printing Service

6.1

CD Print Service Screen

In the “Digital Camera Print Service” screen, register the image files containing no order file, and then do printing from digital cameras. This screen processes the image files written to the CDR in the Data Writing Service. (ex:FUJICOLOR CD, FDi CD)

1

2 3

4 5

6

7

21 8 20 19

9

18

10 11

17

12 13 22

No.

16

Item

15

14

Description

1

Order Number


2

Output


3

Frame No.


4

Print Q’ty

Enter the number of prints in this box. If you create the index print only, enter “0” in this box, and then specify number of index or large index prints in [12 Index/ Large Index Print Setting].

5

Print Size


6

Resize


7

Help

Displays the “Help” screen.

67

No.

Item

Description

8



9



10

Order Regist.


11

View and Order


12


Select [Yes] or [No] to print index/large index prints and specify the number of prints.To add the data on the front print, check the [DSC data] box. Only Index Print Creation: If you create the index print only, spcify number of index or large index prints, while entering “0” in [Print Q’ty] box.

13

Order Reset


14

Cancel


15

Set


16

Select All

Click this button to select all images in the [File Name] column.

17

Order Specification [Image file name]: Column Names of registered image files [Directory]: Name of the directory containing the image files [Image No.]: Serial number of registered images [Print Q’ty]: Number of prints [Service type]: [CD-R Reprint] appears according to the image file format. [Size]: Print size of registered image files [Resize]: [Fill-in], [Fit-in] or [No resize] appears according to the selected resize type.

18

Search


19

File Name


20

Directory


21

Directory No.


22


If the image file name is long, the scroll bar appears.

68

6.2

CD Printing Procedures

Register the order for images written to the CD in the Data Writing Service, and then print them in FRONTIER. Set the CD in the CD drive.

DS014


Select the [OUTPUT] device.



69

Select the folder.

In the CD Print Service screen, select the folder in which the images are stored.

Select the images.





70

Specify if or not the index/large index is outputted, and its output size, and then if the DSC date is printed or not.

Specify if or not the index/large index is outputted, size, and then if the DSC Date is printed or not.



71






72

The ”Confirmation” dialog appears.


DS014-2


Click.


73


(FRONTIER 350/370/390)

74

(FRONTIER 330/340)

6.3


6.3.1 Changing of Media Drive Setting Change the media icon that appears in the [INPUT] field in the “Printing” screen. (See “4.5.1 Changing of Media Drive Setting” on page 40.)

6.3.2 Changing of Output Device Setting Change the device name for FRONTIER. (See “4.5.2 Changing of Output Device Setting” on page 42.)

6.3.3 Master Balance Adjustment Change the master balance for CD-R Reprint. In the “Print Service - Administration” screen, click the [Master Balance] button.


In the “Master Balance” screen, change C, M, Y and D values in the [CD-R Reprint] field.

Change C, M, Y and D in the [CD-R Reprint] field.

75


Click.

76

7

Backup Order Function

Backup Order Function is the function where you can store temporarily the orders from the external application (Kiosk, etc.), and later can correct these orders by using the View and Order screen. The device for backup order function is defined in the “C:\FE\FEIN\InUkBackup.ini” file. By default, the following settings are used, You can also edit them according to your using environment. [Backup Device] Cnt=1 1=Print Service 2=DPC Print 3=NET If you want to add “KIOSK” device, modify it as shown below. [Backup Device] Cnt=2 1=Print Service 2=KIOSK ■

Main Screen

By setting the Backup Order Function, [Backup Order] button, [Paper Surface] column and Backup List switching buttons are added to the Printing Screen. [Backup Order] button

Backup List switching buttons

[Paper Surface] column

77

Click the [Backup List] button in the main screen to display the backup list, and the [Backup Order] button is activated. [Backup Order] button is activated.

Click.

NOTE: The backup order function is available only when the [Wait] order exists. If you set the autoprint mode in FRONTIER, click the [HOLD] button to hold the order, and when using the backup order function, click the [REPRINT] button to make the order [Wait]. Select the order and click the [Backup Order] button.

Select an order.

78

Click.

Complete the order registration by using the same procedures as DSC Printing. (See “4.2 DSC Printing Procedures” on page 28.)

[Test Print] button is added to the function key line in the View and Order screen(opened by clicking of [View and Order] in print service screen).

[Test Print] button is added.

Click the [Test Print] button.

Click.

Registration is done. Click the [OK] button.

Click.

79

Registered order (with order No + “T”) is displayed in the Printing screen.

Registered order (with order No + “T”).

■

Paper Surface Selection

The [Paper Surface Shows] check box is added to the “Print Service- Administration” screen. The surface name is indicated with the print size name, so to identify it, we recommend that you register the size with the indication such as alphabet showing the surface name.

[Paper Surface Show] field is added.

80

■

Additional Items to Writing Service

[Output device Additional]

The following devices are added to the Digital Service Selection list.

Service Name

Functions

FDi CD1 FDi CD2

Three types of FDi CD are added. Additional data such viewer can be written.

FDi CD3 FDi CD with FCD

FUJICOLOR CD with FDi CD(higher- or lower pixels)

Pro CD

In this service the order uses the print size selected in the Print Size setup in film scanning, while the original image size is adopted in the DCS Printing.

[Picture Rotate] The radio buttons selecting the upper side are added to the frames in the Image List screen. Radio buttons are added.

81

To display these radio buttons, add the check mark to [Yes] box in [Picture Rotate] in the Writing Service-Administration screen.

Check [Yes] box.

82

8

Print-to-Print

Scan a photo with the flatbed scanner, and then print the scanned image.

8.1

Print-to-Print Service Screen 1

2

5

3

4

6 7 8

9 10 11 12 13 14 15 17 16 No.

Item

Description

1

Order Number

Shows the order number that is incremented each time an order is registered.

2

Output Device

Output device that had been set in the “Print-to-Print Administration” screen.

3

Admin.

Click this icon to do the Print-to-Print Administration settings for the “Print-toPrint” screen.

4

Help


5

TWAIN Source/ Scanner Type

TWAIN source and Scanner type that had been set in the “Print-to-Print Administration” screen.

6

Pre Scan

The pre-scan is done with the low-resolution reading, mainly for the purpose of checking the images size and scanned position before fine-scan. Set a photo and then click [Pre Scan] button.

7

Print Quantity

When the scanned image appears in the [Image Preview] after the pre-scan, set the number of prints.

8

Print Size

Select a print size, and then adjust rotation, magnification and frame position for the image to be fine-scanned. The magnification and position of the frame can also be adjusted by dragging each corner of the rubber band toward the inside or outside of the image.

9

Without Margin

By checking this box, the image will be printed as an actually scanned size.

10

Instax

Check [Instax] box to apply sharpness effect in the [Instax] printing.

83

No.

Item

Description

11

Fine Scan

The fine-scan is done with the high-resolution reading.

12

Color Balance Adjustment

When the scanned image appears in the [Image Preview] after the fine-scan, adjust the color balance and density if necessary. -15 to +15.

13

Apply

Displays the image to which changed color balance has been applied.

14

Add Image to Order

Click this button to add the scanned image to the order. The number of images that have been added to the order is displayed in the [Image Number] box.

15

Order Regist.

When scanning in the order is completed, click this button to register the order.

16

Cancel Order

Cancels scanning.

17

Return

Returns to the “Printing” screen.

84

8.2

Print-to-Print Procedures Set the photo to the flatbed scanner.

FD191

In the [OUTPUT] field, select the output device.

Select the [OUTPUT] device.

Select the processing type after scanning. • [sRGB]

: Printing in FRONTIER

• [HR]

: Hyper-Retouching

• [Variety]

: Variety-Printing

85

Click.

Click [Pre Scan] button.

Set the number of prints.

When the scanned image appears, set the print quantity, and then select the print size.

Select the print size. Click.

Adjust the printing position by clicking the arrow button in the [Frame Position] column or by clicking the end of the rubber band.

Adjust the printing position.

86

When the print size, frame position and image magnification adjustment are completed, click the [Fine Scan] button.

Click the [Fine Scan] button.

Adjust the color balance by changing C,M,Y and D. Key steps of CMYD : -15 to +15 The changed C, M, Y, and D values can be checked in the Preview by clicking [Apply]. It is not necessary to scan again after the key corrections are done.

Adjust the color balance.

Click the [Add image to Order] button to add the scanned image to the order.

Click the [Add image to Order] button.

87

Click the [Order Regist.] button to register the image.

Click.

Click the [Return] button.

Click.

Completion of Order Registration

Registering of order is completed. Remove the photo from the scanner, and store it in a safe place.


(FRONTIER 350/370/390)

88

(FRONTIER 330/340)

Process the images in Imaging Controller.

Hyper-Retouching [C11]

Variety-Printing [C10]

89

8.3


8.3.1 Changing of Media Drive Setting Set up the executive file for driving the scanner. Normally this setting is not required once it is selected. Click the [Admin.] button.


Enter “DI”.


Click.

In the “Print Service - Administration” screen, click the [Media Drive] button.


90

In the “Media Drive Setting” screen, select the icon and path for the Print-to-Print.

Select the icon and path for the Print-to-Print.

Icon

File Path

PtoP

C:\FE\scanner\scanapp.exe


Click.

91

8.3.2 Changing of Print-to-Print Setting Change the settings for the Print-to-Print. Click the [PtoP] button.

In the “Printing” screen, click the [PtoP] icon.

Click.

In the “Print-to-Print” screen, click the [Admin.] button.

92

Change the settings as shown in the following table.

IMPORTANT Before changing these settings, the flatbed scanner must be connected and the specified TWAIN driver be properly installed.

5

1

2 3 4 8 9 7

6 No.

Item

Description

1

Output Device

Select the output device from the Output Device pull-down menu.

2

Print Size

Select the default print size from the Print Size pull-down menu.

3

TWAIN Source

Select the TWAIN source from the TWAIN Source pull-down menu. Enter any of the following TWAIN sources. Microtek Scanmaker 4:Microtek ScanWizard (32bit) EPSON Expression 1600/1680: EPSON TWAIN Pro (32bit)

4

Scanner Type

Select the Scanner type from the Scanner Type pull-down menu.

5

Scanner Balance

Adjust the master color balance for this service after the fine scan is completed. (Value: -99 to +99)

6

Monitor Balance

Adjust the monitor color balance for this service after the fine scan is completed. (Value: -99 to +99)

7

Contrast

Adjust the contrast for the highlight or the shadow part of the image after the fine scan is completed. (Value: -5 to +5)

8

OK

Sets all settings then returns to the main screen

9

Cancel

Cancels all settings then returns to the main screen.

5, 6 and can be set only after the fine scan is completed.

93

9

CD/Media Writing Service

In the CD/Media Writing Service, you can write the image data from film-scanning or DSC image data, to CD-R or various media.

Writing Service Main Screen

9.1

Register the order(s) for printing with the image data file(s). After the registration, print them by issuing the printing command in FRONTIER.

1

7

2

3

4 5 12

13 11

15 6 14

No.

94

8

9

Item

10

Description

1

Order Number

Displays the number of the selected order.

2

Admin.

Click this button to perform the administrative settings of the writing service.

3

Help


4

Output Drive

Displays the selected output drive for CD-R writing.

5

Copy

Creates the copy of the user’s CD-R to which the images are written. (See “9.5.1 CD-R Copy Procedures” on page 119.)

6

Index

Performs the Index Print Creation with the user’s CD-R to which the images are written in the Writing Service. (See “9.5.2 Index Print Creation from CD-R” on page 123.)

7

Recover

In the case of the occurrence of writing error, click this button to perform the Recover program of the CD-R.

8

Add ↔ New

Changes the status from [New] to [Add] or from [Add] to [New].

9

Connected Devices

Displays the output device other than CD-R for media writing service.

No.

Item

Description

10

Digital Reorder

Click this button to open the “Digital Reorder” screen.

11

Order Registration Status

Displays the order number, service type, status, creation date, etc. of the order that was digitized in FRONTIER or registered in the Print Service.

12

Trash

Deletes the selected order(s).

13

Execution

Starts up the optional software such as “Hyper-Retouch” [B11].

14

Repair

Changes the status of an order from [done] to [wait]. Or if you want to restore an error order, also select the error file, then click this button.

15

Version Display

Shows the version number of installed application.

If the CD-R drive icon does not appear on the screen, make sure that the drive name and SCSI-ID are correctly set in the Administration screen. (See “9.6.1 Data Writing Administration” on page 126.)

95

9.2

CD/Media Writing Procedures

9.2.1 Film Digitizing in FRONTIER ■ FRONTIER 350/370/390

In the “Main Menu” screen, select [Print], and then click the [OK] button.

Prepare the order of the image data created by digitizing the 135, APS or other film on the FRONTIER. In the printing screen of the FRONTIER330/ 350/370/390, select: “Printing(2)” - “Print Mode Select(6)” - “Digital Image Export”. When selecting “Digital Image Export and Print”, two scans are performed: the first scan for data writing and the second for printing. When the scan for data writing is completed, the scan for printing starts. During scanning, in the upper right-hand corner of the printing screen, the BLUE status bar is displayed in “Digital Image Export”, while the GREEN status bar is displayed in “Digital Image Export and Print”. Select a service type.

In the “Output Device Selection” screen, select a service type from the list, and then click [OK] button. These service types can be set in the “Service Type Setting” screen. (See “9.6.4 Service Type Setting” on page 130.)

Click.

96

Select [Create].

In the “Order Condition Settings” screen, select [Create] in the [Work Select] column, and then click the [START] button. (See “9.2.2 Order Condition Settings Screen” on page 103.) In the [ID] box, the machine ID set in the FRONTIER “DI-Manager Administration” screen is displayed. This ID is added to the order No. to identify the machine in the multiple FRONTIER system. When selecting [Free Export JPG] in the “Output Device Selection” screen, the “Order Number Setting” screen Check.

appears in place of the “Order Condition Settings” screen.

Order condition appears.

The bar indicating [File format + Order No. + Condition + No. of Sheet(s)] appears at the top of the “Printing” screen.

Insert the film into the carrier.

EZ638

97

The images are displayed. When digitizing starts, [Waiting to be converted] status appears in the “Data Writing” screen on the Imaging Controller.

Top of the image

For each image, use [F1] key to set the top position of the image, and correct color and density if necessary, and then press the [Start/ Enter] key.

Color Correction Density Correction

The “Fine-scanning” message appears.

In the “Check for end of Order” screen, click [End]. Functions of buttons are as follows: [End]

98

: Stops writing. If you want to start another writing with a different size and type of film, click this button to display the “Output Device Selection” screen.

[Continue] : Continues writing with the same service in the same order. [Next order] : Stops this order writing and starts from the next order scanning with the same service. The “Exporting the image data” message appears. When control returns to the “Printing” screen, perform data writing into the media on the Imaging Controller. (See “9.2 CD/Media Writing Procedures” on page 96.)

99



Click [Digital Image Export] or [Digital Image Export and Print].

In the “Order Information” screen, click the [Digital Image Export] button or when creating the print at the same time as digitizing, click the [Digital Image Export and Print] button.

Select the favorite service.

In the “Digital Service Selection” dialog, select the favorite service, and then click the [OK] button.

Click.

100

Set up the conditions.

In the “Order Condition Settings” screen, set up the conditions (See “9.2.2 Order Condition Settings Screen” on page 103.) and click the [START] button.

Click.

Control returns to the printing screen and the preparing for digitizing is done.

Insert the film into the carrier.

CD764

101

The images appear in the printing screen.

Click the [START] button, or press the [START/ ENTER] key to start digitizing.

Click.

Upon completion of printing, press the [Sort] key to display the “Order Data Display” screen. Click the [OK] to close it.

Click.

When the “Check for end of Order” screen appears, select the action to be taken. End: Ends this order. Continue: Continue digitizing in the current order. Next: Continue digitizing as the next order.

102

9.2.2 Order Condition Settings Screen 2

1 5

3

4

The above is an example of the FRONTIER 330/340 screen.

No.

Item

Description

1

Work Select

Selects [Create] for a new writing or [Modify] for a data addition to the existing order. Check [Modify] to start the condition settings for order modification.

2

Order No.

Displays the order number assigned automatically by the system. The number can also be entered manually. To faciliate the order management, it is recommended to write down this number on the envelope.

3

ID

Identifies the machine in the multiple FRONTIER system.

4

Condition

Selects [Overwrite] to overwrite the data with the same frame number of the film, or “Add” to add them regardless of the frame number.

5

Sort No.

Displays the sort number assigned automatically by the system.

The film order creation can be performed while the processor solution temperatures are being increased.

103

9.2.3 Writing Procedures Click the [Writing] icon.

Click the [Writing] icon to display the “Writing” screen.

Double-click the number of an order listed in the Order Registration Status field, or select an order and then click the [Excecution] button.

Double-Click.

In case of “Free Export”

Double-Click.

In the Image List screen, check the image(s), set the number of copies, delete any images or sorts if necessary, set [Yes] or [No] to create the index/large index prints, and then click [OK] button. (For details, see “9.2.4 Image List Screen for Writing Service” on page 108.)

Insert the media into the drive.

C45015

104

Click [Brows...] to select the media drive, and then click the [OK] button twice.

Select the media drive.

Click.

Click.

■ About [Position Change] function

Use this function to replace the order of frames. Click [Position Change] button to display the four arrows, and then select the frame and use these arrow to change the order. Also by clicking [Reverse] button, the current order can be reversed .

105

Insert the CD-R into the drive.

C45019

Click [OK] button. In case of media writing, insert the specified media instead of CD-R.

Click.

The writing is started.

106

Click [OK] button to complete writing.

Click.

Click.

Upon completion of writing, remove the CD-R from the drive.

C45020

C45016

107

9.2.4 Image List Screen for Writing Service 1

2

3

4

5

6

9

7 8 11 15

12 13 14

10

No.

Item

Description

1

Order Number

Displays the number of the selected order.

2

Sort No.

Displays the sort number.

3

Sorts

Displays the number of sorts in the order.

4

Images

Displays the number of images in the order.

5

CD-R Copy

Enters the number of CD-R copies.

6

Help


7

Previous Sort

Displays the images in the previous sort.

8

Next Sort

Displays the images in the next sort.

9

Pre Page

Displays the images in the previous page in the same sort.

10

Next Page

Displays the images in the next page in the same sort.

11

Position Change

Click this button to change the order that is currently displayed.

12

Image Deletion

Deletes the selected image.

13

Sort Deletion

Deletes the sort that is currently displayed.

14

Index/Large Index

Select “Yes” or “No” to create the index print and large index print. Available large index size is 8 × 10 or A4.

15

Position Change


108

9.3

Writing from DSC/Media

Create an order for writing the DSC and Media data to a CD-R or other media in the “Printing Service” screen. Insert the media into the drive.

FD121

In the “Printing Service” screen, click [Writing] button in the [OUTPUT] field.

Click. Click the media icon.

Click the media button in the [INPUT] field.

In the “Service Select” screen, select a service type, and then click [OK] button.

Select a service type.

Click.

109

Select the holder.

In the “DSC Print Service” screen, select the folder in which the images are stored.

Select the Images.




110






FD124

111


Click.

Click the [Writing] icon.

Click the [Writing] icon to display the “Writing” screen.

Double-click the order in the [Order Registration] Status field, or select an order and then click the [Execution] button.

Double-Click.

112

Double-Click.

In case of “Free Export”

In the Image List screen, check the image(s), set the number of copies, delete any images or sorts if necessary, set [Yes] or [No] to create the index/large index prints, and then click [OK] button. (For details, see “9.2.4 Image List Screen for Writing Service” on page 108.)

Insert the media into the drive.

C45015

Click [Brows...] to select the media drive, and then click the [OK] button twice.

Select the media drive.

Click.

Click.

113

■ About [Position Change] function


Insert the CD-R into the drive.

C45019

Click [OK] button. In case of media writing, insert the specified media instead of CD-R.

Click.

114


Click [OK] button to complete writing.

Click.

Remove the CD-R from the drive.

C45020

Click.


C45016

115

9.4

Index Print Creation

■ FRONTIER 350/370/390

In the printing screen, select [Printing(2)] - [Print Mode Select(6)] - [Digital Image Import(sRGB)].

Select [Printing (2)]-[Print Mode Select (6)][Digital Image Import (sRGB)].

Select [Index Print] or [Large Index Print] and click [OK]. Select [Index Print] or [Large Index Print].

Click.

The “PR Status Notice” appears and printing starts.

116

The order information is displayed in the [Done] column. Click the [End] button.

Click the [End] button.

117



In the “Order Information” screen, click the [Printing from Imaging Controller] button.

Click.

In the “Color Space Selection” dialog, select the color space, and then click the [OK] button.

Select the color space.

Click.

Printing is started.

118

9.5

Special Operations

9.5.1 CD-R Copy Procedures Do the following procedures to make duplication of the CD-R with the one that was created through “Data Writing” process. In the “Writing” screen, click the [Copy] button.

Click the [Copy] button.

Enter the order number.

In the “CD-R Duplicate” screen, enter the order number and the number of copies, and then click the [OK] button.

Enter the number of copies.

Click.

The CD-R (source) insertion message appears.

119

Insert the user’s CD-R (source) into the CD-R drive.

DS014

Click [OK] button.

Click.

The CD-R (destination) insertion message appears.

Insert a new CD-R (destination) into the CD-R.

C45019

120

Click [OK] button. Remove the user’s CD-R from the CD-ROM drive, and then click the [OK] button.

Click.


The CD-R (source) removal message appears.

Remove the CD-R (source) from the drive.

DS014-2

121


Click.

Upon completion of writing, click the [OK] button.

Click.

Remove the CD-R (destination) from the CD drive.

C45020

122

9.5.2 Index Print Creation from CD-R Do the following procedures to create multiple index prints with the user’s CD’R. In the “Writing” screen, click [Index] button.

Click the [Index] button.

Enter the order number and the number of copies, then select [Index] or [Large Index], and a media, and then click the [OK] button.

Enter the number of copies.

Select any.

Select a media.

Click.

The media insertion message appears.

123

Insert the user’s CD-R into the drive.

DS014


Click.

When creating is completed, click the [OK] button and then remove the user’s media from the drive, and then click the [OK] button.

Click.

The media removal message appears.

124

Remove the CD-R from the CD drive.

DS016


Click.

The [Index Print] order appears in the “Printing” screen.

125

9.6


9.6.1 Data Writing Administration Perform the writing service administrative settings on the “Administration” screen. Click the [Admin.] button.

In the “Writing” screen, click the [Admin.] button.

Enter “DI”.


Click.

Change the settings in the “Writing ServiceAdministration” screen as shown in the table below.

4

3 13

1 2

14 15 16 17

5

6 7 8 11

9

12

10

126

18

19

No.

Item

Description

1

Adapter No. - SCSI ID

Selects an appropriate combination of SCSI HOST Adapter number and SCSI ID for the CD-R drive.

2

CD-R Drive Name

Selects the drive name for the CD-R drive.

3

CD-ROM Drive Name

Selects the drive name for the CD-ROM drive.

4

Verify Type Selection

Verify after writing (new CD-R): Check the box to verify the CD-R after writing. Normally remove the check. Verify after writing (additional data): Check the box to verify the CD-R after writing. Normally check.

5

Media Drive

Displays the drives set for writing in the “Media Drive Setting” screen.

6

Media Drive Setting

Displays the “Media Drive Setting” screen. (See “9.6.2 Media Drive Setting” on page 128.)

7

Optional Software Setting

Displays the application software set in the “Optional Software Setting” screen. [Setting] button: Displays the “Application Software call setup” screen.

8

CD-R Index Setting Sets the device for printing the CD-R index and large-index prints, and their print size, and then sets [Yes] or [No] to print them. [Device]: Selects the device for printing the CD-R index or large-index prints. For large index print, normally select [A4(210x297mm)] or [8R(203x254mm. 254x203mm)]

9

Print Size

Click [Select] to display the Print Size Selection screen.

10

Index/Large Index

Sets the default value for [Yes] or [No] to Index/Large Index in “Image List” screen.

11

Writing Speed

Select the writing speed of CD drive. Fast : Maximum speed of the CD drive. Normal : 8x (fixed)

12

Data Delete Interval

Sets up the time to delete the completed order.

13

Help


14

Version Info.

Displays the version information.

15

Statistic Log

Display the “Statistic Log” screen.

16

Service Type Setting

Displays the “Service Type Setting” screen.

17

Multiple Service

Displays the “Multiple Service” screen.(See “10 Multiple Service” on page 133.)

18

OK

Stores the settings and exits this screen.

19

Cancel

Exits this screen without storing the settings.

127

9.6.2 Media Drive Setting On the “Writing service Administration” screen, click [Media Drive Setting] in the [Media Drive] field to open the “Media Drive Setting” screen, on which you can set up the icons and letters of the drives connected to the Imaging Controller. 1

2

3

4

No.

128

Item

5

Description

1

Icon

Selects the icon for drive.

2

Drive

Selects the drive letter for each media drive.

3

Help

Display the “Help” screen.

4

OK


5

Cancel


9.6.3 Optional Software Setting On the “Writing Service Administration” screen, click [Setting] in the [Optional Software Setting] field to open the “Optional Software Setting” screen, on which you can set the FUJIFILM optional software (up to three software programs). For example, when using the Digital Photo Center, use the pull-down menu to select “Digital Reorder”, and then specify “C:\FE\DR\DigitalReorder.exe” as Path for the Optional Software.

2

3

4

1

5

6

No.

Items

Description

1

Icon

Selects the icon for the software.

2

Path for the Optional Software

Enter the full path name to locate the selected software.

3

Help


4

Brows.

Displays the file selection screen for selecting the file. The selected file appears in the Path for the Optional Software Output Path. Select only the file with “.exe” extension.

5

OK


6

Cancel


129

9.6.4 Service Type Setting Use the “Service Type Setting” screen for setting the type of several writing service combinations of Media Type, File Format and Image Size. On the Writing Service Administration screen, click [Service Type Setting] to open the “Service Type Setting” screen.

1

2

3

4

6

No.

Item

5

7

8

Description

1

Service Name

Displays the service name with the media type, file format and image size. The selected service name is displayed in the “Output Device Selection” screen when performing Digital Image Export on the FRONTIER 350/370/390.

2

Media Type

Displays the media type for the writing service. Supported media type: CD-R, Free Export (same function as C2: BMP Export provides)

3

File Format

Displays the selected image file format. Supported file format: JPG(Exif-JPG), FPX, BMP, FUJICOLORCD

4

Image Size (Base)

Displays the type of the image size. Supported image size: 1base, 4base, 16base, Free Size

5

Help


6

Set

Registers the service name with the media type, file format and image size, and enters it in the list.

7

Delete

Deletes the selected service name.

8

Return

Exits this screen.

130

Restrictions for Service Type Combination (1) When selecting “FREE EXPORT” as Media Type, only “Print Size” can be specified as Image Size. (2) When selecting “FUJICOLOR CD” as File Format, “4base” as Image Size and “CD-R” as “Media Type” can only be selected. (3) When selecting “FD” as Media Type, only “1base” can be selected as Image Size. The following table shows the relation between Media Type, File Format and Image Size. Service Composition Media Type

CD-R

ZIP/JAZ/ MO/HD1 to 6 FD Free Export

File Format FPX JPG BMP FUJICOLOR CD FDi CD CD Pro FPX JPG BMP JPG JPG BMP

1Base

Image Size 4Base 16Base

Free Size

Available

Available

Available

Available

N/A N/A N/A

Available Available N/A

N/A N/A N/A

N/A N/A Available

Available

Available

Available

N/A

Only Film Scan

N/A

N/A

N/A

N/A

N/A

N/A

Available

131

9.6.5 Index Print Size Selection On the “Writing Service Administration” screen, click [Select] in the [CD-R Index Setting] field to open the “Print Size Selection” screen, on which you can select the print size for the index print. This service is available only for film scanning.

1

No.

2

3

4

Item

6

Description

1

No.

Displays the serial number.

2

Name

Displays the print size name.

3

Width (mm)

Displays the paper width(mm).

4

Feed (mm)

Displays the paper feed(mm).

5

Width (pixel)

Displays the paper width(pixel).

6

Feed (pixel)

Displays the paper feed(pixel).

132

5

10

Multiple Service

By registering the DI service functions to be used frequently as Multiple Service, you can perform them continuously to complete an order. (For procedures regarding service functions in a multiple service, see the section explaining each procedure.)

10.1

Printing Screen (in use of Multiple Service)

1

No.

Item

2

Description

1

OUTPUT

Available output devices set in the “Printing - Administration” screen. At the time of starting an order registration, select one of the output devices. By selecting the [Multiple] icon, you can start the multiple service. If the multiple service icon is registered in the fifth or later entry, it appears as one of another 4 icons in the reverse field. In this case, click [ | ] to display the reverse area.

2

INPUT

Available input media or devices that have been set in the “Printing Administration” screen. After the selection of [Multiple] icon, click the icon of the media you inserted to start the multiple service. Click [ | ] in the slider bar to display another 9 icons in the reverse field. Up to 18 media or input devices can be registered in this field.

133

10.2

Multiple Service Setting Click the [Admin.] button.


Enter “DI”.


Click.

In the “Print Service - Administration” screen, click the [Multiple service] button.

Click the [Multiple service] button.

134

The “Multiple Service -Administration” screen appears.

2 8 1

9 10 3 4 5 6 7

11

No.

Item

12

13

Description

1

Multiple Service List

Lists up the namse of the multiple services that were registered.

2

Multiple Service Composition

Shows the selected service contents.

3

Multiple Service Name

Enter the name of the service in this column.

4

Print Output Device

Select an output device. This information is registered to the system at the time of “Pre-operational check” in FRONTIER.

5

Image Writing Service

Select a writing service to be registered.

6

Image Use Service Select it when using Digital Reorder or NET service.

7

Other

(Not used)

8

Help


9

1 Line Up

Moves the selected service upward in the Multiple Service List.

10

1 Line Down

Moves the selected service downward in the Multiple Service List.

11

Entry

Adds the selected service to Multiple Service List.

12

Delete

Removes the selected service from Multiple Service List.

13

Return

Returns to the “Print Service - Administration” screen.

135

Select the items to be serviced in the [Service Composition].

Select the items to be serviced.

Enter the name of the multiple service in the [Multiple Service Name].

Enter the name of multiple service.

Click the [Entry] button.

Click.

136

Created service is added here.

The created service is added to the [Multiple Service List].

Click the [Return] button.

Click.

Control returns to the “Print Service Administration” screen.

137

11 11.1

Digital Photo Center Operating Digital Photo Center (DPC) Operation

The DI Print Service allows you to register a print order by the Digital Photo Center connected to the Imaging Controller, and to print with FRONTIER. The Digital Photo Center can be accessed through either of the following two connections: LAN connection or Branch Store connection. The LAN connection allows you to connect the Imaging Controller through the Local Area Network. The Branch Store connection allows you to take an order and copy it to MO media using the Digital Photo Center in the branch store, and to print the order copied to the media using the Imaging Controller and FRONTIER 350/370/390 in the main store. NOTE: When jamming occurs in FRONTIER during printing, you can reprint by using the following screen. To start DPC for Branch Store connection, click [DPC-M].

To start DPC for LAN connection, click [DPC1]-[DPC9].

q Click the [Printing] button shown in the changer at the top of the screen to display the Print Service screen. w To display the “Digital Photo Center” screen for the LAN connection, click [DPC1]-[DPC9]. e To display the “Digital Photo Center” screen for the Branch Store connection, click [DPC-M].

138

11.1.1 Using of LAN Connection q Click one of the icons assigned to DPC1 through DPC9 in the [Input] field at the upper right-hand part of the “Print Service” main screen, to display the “Digital Photo Center” main screen.

w Click the [Reacquire] button to retrieve print orders taken by the Digital Photo Center and to acquire them in the folder specified in the “Administration” screen. • Acquired orders will be listed up.

Click the [Reacquire] button.

139

e Register the order. The order can be registered using the Digital Photo Center Order Sheet issued by the Digital Photo Center. If the Imaging Controller has a bar code reader (keyboard-type), read the bar code on the Digital Photo Center Order Sheet using the reader to register the order(s) automatically. If the Imaging Controller has no bar code reader, select an order to be registered with the mouse, and double-click it or click the [Order Regist] button to register it. If the list includes any order not to be registered, select it with the mouse and click the [Delete] button to delete it. r After registration is completed, click the [Return] button to return to the “Print Service” screen. • In the “Print Service” screen, the order(s) registered in step (3) with [DPC Print] will appear.

DPC order appears.

t Print with FRONTIER Select [DPC Print] on the “Input Select” screen and print ordered images with FRONTIER.

Select [DPC Print].

The above is an example of FRONTIER 350/370/390 screen.

140

11.1.2 Using of Branch Store Connection q Insert the MO media delivered from the branch store into the drive. w Click the [DPC-M] icon in the [Input] field at the upper right-hand part of the “Print Service” main screen. • Control returns to the branch store screen in which the branch store information (at the upper part) and a list of order(s) stored on the MO media are displayed.

e Register an order. Click the [Order Regist] button to register all orders displayed. The progress bar is displayed during order registration. All orders can be registered simply by one operation by this method.

Click the [Order Regist.]button.

141

r After registration is completed, the following dialog is displayed. Remove the MO media and click the [OK] button to return to the “Print Service” screen.

• The list on the “Print Service” screen shows the order(s) registered in step (2) with “DPC Print” in the Input item.

t Print with FRONTIER 330/350/370/390 Select [DPC Print] on the “Input Select” screen and print ordered images with FRONTIER 350/370/ 390 in the same way as other print services.

142

11.2

Operating Digital Reorder Service

When the Digital Reorder Service is selected on FRONTIER, the screen shown below is displayed. You can enter the Envelope number and the User ID in the “Order Condition Settings” screen in the same way as other digitizing services. The serial-type bar-code reader connected to FRONTIER allows you to enter information more easily.

The above is an example of FRONTIER 350/370/390 screen.

NOTE: • It is not necessary to enter values in [Envelope No.] and [User ID] if they are set in the Imaging Controller. • You may select to enter [Envelope No.] or [User ID] depending on your management.

143

This new service allows you to save images digitized by FRONTIER on a hard disk shared on the network, and to view the saved images or to order prints of them using the Digital Photo Center. q Click the [Writing] button shown in the changer at the top of the screen to display the “Writing Service” main screen. • The “Writing Service” main screen shows a list of order numbers for the images digitized by FRONTIER.

w Click the [Digital Reorder] icon shown in the upper right-hand segment of the “Writing Service” main screen. • The “Digital Reorder - Order List” screen will appear and the screen shows a list of order information listed on the “Writing Service” main screen. You can register these orders on this screen as described below:

144

e Register an order using the following procedures. (1) Click and highlight one of the orders listed on the screen, then click the [Order Regist] button to display the order registration screen shown below. (2) Enter the necessary information in the fields below: • Envelope number : Enter the DP envelope number in this field. Otherwise you can enter the number at the start of digitizing with FRONTIER. • User ID : Enter the user ID in this field. Otherwise you can enter the ID at the start of digitizing with FRONTIER. • User Name : Enter the user name. • Memo : Enter additional information on the user such as telephone number and address, if necessary. • Password : Enter a unique user-defined password. You may view the images after entering the password (4-digit) in the Digital Photo Center.

(3) After entering, click the [OK] button to register the order. You will return to the “Digital Reorder” main screen after registration is completed.

145

r Click the [Maintenance] button on the “Digital Reorder” main screen to open the “Digital Reorder - Maintenance” screen. The password to access the “Maintenance” screen is “DI.”

This screen allows you to check information on all registered orders. It also conveniently enables you to determine the number of days remaining until the due date for deleting the image files of an order. You may extend the due date by clicking on the [Term Extension] button if necessary. Image files of an order with no days remaining will be deleted. The image-saving term and extra saving term can be specified on the “Admin.” screen. • DATA Writing Press this button to write the stored images to the media. By using this function, you can make backups of the images that will expire soon. These images will be registered as “Media Writing” order in the “Writing” screen. The order starts from “R”. t Click the [Memo Edit] button on the “Digital Reorder - Maintenance” screen to open the “Memo Edit” screen as shown below. This screen allows you to edit a memo entered for an order number other information can be edited in this screen.

146

11.3

Digital Photo Center Settings

For details of settings, see “Digital Photo Center Installation & Service Manual”.

11.3.1 Drive/Path Setting for DPC Create the [DPCdata] folder in the [D] drive and share it beforehand.

Create [DPCdata] folder.

Perform the drive/path settings for DPC in the “Print Service - Administration” screen. Click [Admin.] button on the “Print Service” screen to display “Print Service - Administration” screen. In the Password screen, enter “DI”.


q Click the [Media Drive] button on the “Print Service - Administration” screen. • The “Media Drive Setting” screen appears.

Specify the icon and file path.

147

w Specify the appropriate icon and drive letter (name). e Specify the appropriate icon and the file path according to the table below. You can also specify the file path by pressing the [Brows…] button. Item Digital Photo Center (LAN connection) DPC 1 to DPC 9 Digital Photo Center (Branch Store connection) DPC-Media

Description C:\FE\kiosk\kiosk.exe X

C:\FE\kiosk\kiosk.exe Append “X” (drive name for DPC-Media) to the extension “exe”. A space must separate File Path from drive name for DPC-Media.

r Click the [OK] button. • Control returns to the “Print Service - Administration” screen.

t Click the [OK] button on the “Print Service - Administration” screen. • Control returns to the “Print Service” main screen. • The specified media drive icons are displayed on the main screen.

Digital Photo Center (LAN Connection)

Digital Photo Center (DPC-Media)

148

11.3.2 DPC Administrative Settings Perform the DPC administrative settings. Click the desired DPC icon in the [Input] field at the upper right-hand part of the main screen. The “DPC” main screen appears. q Click the [Admin.] button on the “DPC” main screen.

w Enter the password “DI.” • The “Digital Photo Center - Administrator” screen appears.

149

e In the “Digital Photo Center - Administrator” screen, set up the three items described below: Create the [DRspool] folder in the [D] drive and share it beforehand.

Create [DRSspool] folder.

(1) Device Name: Select the desired printer device from the pull-down menu in the [Device Name] field. (2) Spool Setting:Click the [Spool Setting] button to display the “Spool Setting” screen, and define the path to the storage medium to which you want to save files ordered through the Digital Photo Center. First, define the path to the storage medium that is shared in the network in the [Root Path] field (D: \DPCdata\).

(3) Print Size: Specify the sizes of the prints ordered by the DPC. Select the desired print size from the pull-down menu in each of the print size fields. After completing all settings, click the [OK] button to return to the DPC main screen.

150

11.4

Digital Reorder Service Settings

For details of settings, see “Digital Photo Center Installation & Service Manual”.

A customer who has ordered simultaneous development and printing of a negative film can ask to have the film images digitized and stored on the Imaging Controller. On subsequent visits, the customer can call out these digitized images on the Digital Photo Center and order reprints of original photographs or edit the images for use in any of the Frontier printing services.

11.4.1 Drive/Path Setting for Digital Reorder IMPORTANT To monitor the orders in the Digital Photo Center, the settings must be done in the “Setup for Digital Photo Center” screen beforehand. ■ Setup for Digital Photo Center

q Insert “DI Print/Data Writing Service Software Ver.4.5” CD into the DVD drive while the “Launcher” screen is opened. w Touch the [Future Release Tools] icon.

Touch.

151

e In the next screen, select [Ver.4.1 or Later].

Select.

r Complete the settings following the screen instructions. ■ Making [DRspool] folder

Create the [DRspool] folder in the [D] drive and share it.

Create [DRSspool] folder.

152

11.4.2 Digital Reorder Service Administrative Settings Perform the settings for Digital Reorder Service using the following procedures. q Click the [Writing] button shown in the changer at the top of the screen. • The “Writing Service” main screen will appear.

w Click the [Admin.] button on the “Writing Service” main screen. e Enter the password “DI.” • The “Writing Service - Administration” screen will appear.

Click.

153

r Click [Setting] in the [Optional Software Setting] field. • The “ Optional Software Setting” screen will appear.

t Set up the (up to three) optional software to be called up using the following procedures. (1) Select [Digital Reorder] from the pull-down menu in the [Icon] field. (2) Enter the file path “C:\FE\DR\DigitalReorder.exe” in the [Path for the Optional Software] field. You can also specify the file path by clicking the [Brows…] button. (3) After completing the settings, click the [OK] button. • Control returns to the “Writing Service - Administration” screen.

y After completing all settings, click the [OK] button. • Control returns to the “Writing Service” main screen.

154

u Click the [Digital Reorder] icon on the “Writing Service” main screen. • The “Digital Reorder - Order List” screen will appear.

i Click the [Admin.] button on the “Digital Reorder - Order List” screen. And enter the password “DI.” o Set the following three items in order for image files digitized by Frontier to be saved for a prescribed period. Set the following three items in order for image.

1

2 3 4

155

No.

Items

Descriptions

1

Image saving period

Image file storage periods are set here. The maximum setting is 999 days.

2

Image save to

Where the image files are to be stored (d:\DRspool)

3

Extra saving term

Although the image files will be deleted when the period of storage time which was set in has expired, the period can be extended by a fixed number of extra days for specific orders. The number of these extra days is set here. The maximum setting is 99 days.

4

Exp. Date announcement

The image files will be deleted when this date expires.

11.4.3 Registering of Digital Reorder Service into Multiple Service When using Digital Reorder Service only in Imaging Controller, register it into Multiple Service beforehand. (For details of Multiple Service Settings, see “10.2 Multiple Service Settings” on page 134.)

156

12

Operation Screens and Function Key List

This chapter explains the operation screens used in the DI Print/Data Writing service [C4/ C5] and useful shortcuts that are assigned to the function keys.

Printing Service

12.1

Screen

Key

Printing Screen

13

12

11

15

1 2

3

4

5

6

7

8

9 10

14

16 17

21

18

19

20

Action

Refer to

F1

[Help] button

1

F2

INPUT - Media1 (10)

2

F3

INPUT - Media2 (11)

3

F4

INPUT - Media3 (12)

4

F5

INPUT - Media4 (13)

5

F6

INPUT - Media5 (14)

6

F7

INPUT - Media6 (15)

7

F8

INPUT - Media7 (16)

8

F9

INPUT - Media8 (17)

9

F10

INPUT - Media9 (18)

10

F11

[Admin] button

11

F12

[Auto] button

12

[Alt] + F1

OUTPUT - reverse

13

[Alt] + F2

INPUT - reverse

14

[Alt] + F4

[EXIT] button

15

[Alt] + F5

[Express] button

16

[Alt] + F6

[Reprint] button

17

[Alt] + F7

[Hold] button

18

[Alt] + F8

[Recover] button

19

[Alt] + F9

[Info.] button

20

[Alt] + F10

[Trash] button

21

157

Screen

Key

Print Service Screen 10

3

9

6

[Help] button

1

F2

Directory

2

F3

File Name

3

F4

[Set] button

4

F5

[Order Regist.] button

5

F6

[Select All] button

6

4

F7

[Search] button

7

5

F8

[View and Order] button

8

8

F9

[Return] button(in Search screen)

—

F10

Print Size

9

F11

Order Number

10

F12

Print Q’ty

11

F1

[Help] button

1

F5


2

F6

[Order File Info.] button

3

F7

Free Order

4

F8

View and Order

5

F11

Order Number

6

1

11

COS Print Service Screen 6

1

3 4 2 5

158

Refer to

F1

2

7

Action

Screen

Key

DPOF Print Service Screen 5

1

Action

Refer to

F1

[Help] button

1

F5


2

F7

[DPOF Cancel] button

3

F8

[View and Order] button

4

F11

Order Number

5

F1

[Help] button

1

F2

[All/Order] button

2

F3

[Page/Order] button

3

F5

[Sharpness] button

4

F6

[Scene Correction] button

5

F7

[Auto Correction] button

6

F8

Q’ty

7

F9

Hold/Hold Cancel

—

F10

Auto Correction ON/OFF

—

F11

D+3

—

0

D-3

—

1

D-1

8

2

N

3

D+1

4

C+1

5

M+1

6

Y+1

7

C-1

8

M-1

9

Y-1

3 2 4

View and Order Screen

8

1

7

9

2

3

4

5

6

9

[Back Space] Manual Correction Cancel

—

[Space]

—

Image Registration Cancel

[Cursor] key Image Selection

—

159

Screen

Key

Print Service - Administration Screen 1 4 5 6 7 8 9 10 11

2 3

160

Action

Refer to

F1

[Help] button

1

F2

[OK] button

2

F3

[Cancel] button

3

F4

[Version Info.] button

4

F5

[Static Log] button

5

F6

[Monitor Adjust] button

6

F7

[Master Balance] button

7

F8

[Media Drive] button

8

F9

[Output Device] button

9

F10

[Multiple Service] button

10

F11

DSC Setting

11

12.2

Data Writing Service Screen

Key

Writing Screen 7 9

1

3 2 4

8

5

Action

Refer to

F1

[Help] button

1

F3

[Copy] button

2

F4

[Recover] button

3

F5

[Add->New] button

4

XX

[Execution] button

5

XX

[Repair] button

6

F11

[Admin.] button

7

F12

[Trash] button

8

[Alt] + F4

[EXIT] button

9

F1

[Help] button

1

F2

[OK] button

2

F3

[Position Change] button

3

F4

Reverse Sorting

4

[HOME]

[Previous Sort] button

5

[END]

[Next Sort] button

6

[PageUp]

[Pre Page] button

7

6

Image List Screen

1 7

5 6 3

4 9 10

[PageDown] [Next Page] button

8

[Delete]

9

I[mage Deletion] button

[BackSpace] [Sort Deletion] button 2

8

[Up]

Image Selection(red frame) Up

[Down]

Image Selection(red frame) Down

[Left]

Image Selection(red frame) Left

[Right]

Image Selection(red frame) Right

10

—

[Shift] + [UP] Image Order Change - Up

[Shift] + [Down] Image Order Change - Down [Shift] + [Left] Image Order Change - Left

—

[Shift] + [Right] Image Order Change - Right

161

Screen

Key

Writing Service - Administration Screen

F1

1

162

Action [Help] button

Refer to 1

12.3

Print-to-Print Service Screen

Key

Print-to-Print Screen 2

1

3

Action

Refer to

F1

[Help] button

1

F2

[Admin.] button

2

F3

[Pre Scan] button

3

F4

[Fine Scan] button

4

F5

[Apply] button

5

F6

[Add Image to Order] button

6

F7


7

F8

[Cancel Order] button

8

4

F9

[Return] button

9

5

[Alt+F4]

Exit

—

F1

[Help] button

1

6 7 9 8

Print-to-Print - Administration Screen 1

163

12.4

System Screen

Key

System Status Screen

2 3

1

System - Administration Screen

1

164

Action

Refer to

F1

[Help] button

1

F8

[Admin.] button

2

[Alt] + F4

[EXIT] button

3

F1

[Help] button

1

13

Index

A About the [HOLD] in the View and Order Screen.. 35

B Backup Order Function ............................................. 77 ———Additional Items to Writing Service ............. 81 ———Main Screen ................................................... 77 ———Paper Surface Selection ............................... 80 Backup Order Function Installation/Setup ............... 8

C CD/Media Writing Procedures ................................. 96 CD/Media Writing Service ........................................ 94 CD Printing Procedures ............................................ 69 CD Printing Service ................................................... 67 CD Print Service Screen........................................... 67 ———Cancel ............................................................. 68 ———Directory .......................................................... 68 ———Directory No.................................................... 68 ———File Name........................................................ 68 ———Frame No. ....................................................... 67 ———Help.................................................................. 67 ———Horizontal Scroll Bar ..................................... 68 ———Index/Large Index Print Setting ................... 68 ———Order Number ................................................ 67 ———Output .............................................................. 67 ———Order Regist ................................................... 68 ———Order Reset .................................................... 68 ———Order Specification Column ......................... 68 ———Print Q’ty ......................................................... 67 ———Print Q’ty buttons ........................................... 68 ———Print Q’ty Display ........................................... 68 ———Print Size ......................................................... 67 ———Resize.............................................................. 67 ———Search ............................................................. 68 ———Select All ......................................................... 68 ———Set .................................................................... 68 ———View and Order .............................................. 68 CD-R Copy Procedures .......................................... 119 Changing of Media Drive Setting .........40, 65, 75, 90 Changing of Output Device Setting ........... 42, 65, 75 Changing of Print-to-Print Setting ........................... 92 ———Cancel ............................................................. 93 ———Contrast ........................................................... 93 ———Monitor Balance ............................................. 93

———OK .................................................................... 93 ———Output Device ................................................ 93 ———Print Size ......................................................... 93 ———Scanner Balance ........................................... 93 ———Scanner Type ................................................. 93 ———TWAIN Source ............................................... 93 COS Printing Procedures ......................................... 56 COS Print Service Screen........................................ 54 ———Cancel ............................................................. 55 ———Free Order ...................................................... 55 ———Index/Large Index Print Setting ................... 55 ———Order File Info. ............................................... 55 ———Order Regist ................................................... 55 ———Order Reset .................................................... 55 ———Order Specification Column ......................... 54 ———Print Q’ty Display ........................................... 55 ———View and Order .............................................. 55

D Data Writing Administration ................................... 126 ———Adapter No. - SCSI ID ................................ 127 ———Cancel ........................................................... 127 ———CD-R Drive Name........................................ 127 ———CD-R Index Setting ..................................... 127 ———CD-ROM Drive Name ................................. 127 ———Data Delete Interval .................................... 127 ———Help................................................................ 127 ———Index/Large Index ........................................ 127 ———Media Drive .................................................. 127 ———Media Drive Setting ..................................... 127 ———Multiple Service............................................ 127 ———OK .................................................................. 127 ———Optional Software Setting .......................... 127 ———Print Size ....................................................... 127 ———Service Type Setting ................................... 127 ———Statistic Log .................................................. 127 ———Verify Type Selection .................................. 127 ———Version Info .................................................. 127 ———Writing Speed ............................................... 127 Digital Camera Print Service Screen ...................... 26 ———Cancel ............................................................. 27 ———Directory .......................................................... 27 ———Directory No. .................................................. 27 ———File Name........................................................ 27 ———Frame No. ....................................................... 26

165

———Help.................................................................. 26 ———Horizontal Scroll Bar ..................................... 27 ———Index/Large Index Print Setting/ DSC Data ........................................................ 27 ———Order Number ................................................ 26 ———Order Regist ................................................... 27 ———Order Reset .................................................... 27 ———Order Specification Column ......................... 27 ———Output .............................................................. 26 ———Print Q’ty ......................................................... 26 ———Print Q’ty buttons ........................................... 27 ———Print Q’ty Display ........................................... 27 ———Print Size ......................................................... 26 ———Resize.............................................................. 26 ———Search ............................................................. 27 ———Select All ......................................................... 27 ———Set .................................................................... 27 ———View and Order .............................................. 27 Digital Photo Center ................................................ 138 Digital Photo Center Settings ................................ 147 Digital Reorder Service Administrative Settings .................................... 153 Digital Reorder Service Settings ........................... 151 DPC Administrative Settings.................................. 149 DPOF Printing Procedures ...................................... 61 DPOF Print Service Screen ..................................... 60 ———Cancel ............................................................. 61 ———DPOF Cancel ................................................. 60 ———DPOF Icon ...................................................... 60 ———Order Regist. .................................................. 60 ———Order Selection Column ............................... 60 ———Print Q’ty Display ........................................... 60 ———View and Order .............................................. 60 ———Index/Large Index Print Setting ................... 61 Drive/Path Setting for Digital Reorder .................. 151 Drive/Path Setting for DPC .................................... 147 DSC Printing Procedures ......................................... 28 DSC Printing Service ................................................ 26 DSC Setting ................................................................ 45

F Features ........................................................................ 6 Film Digitizing in FRONTIER ................................... 96 ———FRONTIER 330/340 .................................... 100 ———FRONTIER 350/370/390 .............................. 96

166

I Image List Screen for Writing Service .................. 108 ———CD-R Copy ................................................... 108 ———Help................................................................ 108 ———Image Deletion ............................................. 108 ———Images ........................................................... 108 ———Index/Large Index ........................................ 108 ———Next Page ..................................................... 108 ———Next Sort ....................................................... 108 ———Order Number .............................................. 108 ———Position Change .......................................... 108 ———Pre Page ....................................................... 108 ———Previous Sort ................................................ 108 ———Sort Deletion ................................................. 108 ———Sort No. ......................................................... 108 ———Sorts .............................................................. 108 Index Print Creation ................................................ 116 Index Print Creation from CD-R ............................ 123 Index Print Creation ———FRONTIER 330/340 .................................... 118 ———FRONTIER 350/370/390 ............................ 116 Index Print Size Selection ...................................... 132 ———Feed (mm) .................................................... 132 ———Feed (pixel) ................................................... 132 ———Name ............................................................. 132 ———No................................................................... 132 ———Width (mm) ................................................... 132 ———Width (pixel).................................................. 132

M Making [DRspool] folder ......................................... 152 Master Balance Adjustment ........................ 44, 65, 75 Media Drive Setting ................................................. 128 ———Cancel ........................................................... 128 ———Drive .............................................................. 128 ———Help................................................................ 128 ———Icon ................................................................ 128 ———OK .................................................................. 128 Media Handling ............................................................ 9 ———CD-R ................................................................ 16 ———Compact Flash ............................................... 11 ———FD .................................................................... 17 ———Memory Stick SD Memory Card.................. 13 ———MO ................................................................... 14 ———PC Card ............................................................ 9

———Smart Media ................................................... 10 ———Zip .................................................................... 15 Media Pinting Service (with order file).................... 54 Media Printing Service .............................................. 47 Media Printing Service (without order file) ............. 47 Media Printing (without order file) Procedures...... 49 Media Print Service Screen ..................................... 47 ———Set .................................................................... 48 ———Cancel ............................................................. 48 ———Directory .......................................................... 48 ———Directory No.................................................... 48 ———File Name........................................................ 48 ———Frame No. ....................................................... 47 ———Help.................................................................. 47

N

———Horizontal Scroll Bar ..................................... 48 ———Index/Large Index Print Setting ................... 48 ———Order Number ................................................ 47 ———Order Regist. .................................................. 48 ———Order Reset .................................................... 48 ———Order Specification Column ......................... 48 ———Output .............................................................. 47 ———Print Q’ty buttons ........................................... 48 ———Print Q’ty Display ........................................... 47 ———Print Size ......................................................... 47 ———Print Q’ty ......................................................... 47 ———Resize.............................................................. 47 ———Search ............................................................. 48 ———Select All ......................................................... 48 ———View and Order .............................................. 48 Multiple Service........................................................ 133 Multiple Service Setting .......................................... 134 ———1 Line Down.................................................. 135 ———1 Line Up ....................................................... 135 ———Delete ............................................................ 135 ———Entry .............................................................. 135 ———Help................................................................ 135 ———Image Use Service ...................................... 135 ———Image Writing Service ................................. 135 ———Multiple Service Composition .................... 135 ———Multiple Service List .................................... 135 ———Multiple Service Name ................................ 135 ———Other .............................................................. 135 ———Print Output Device ..................................... 135 ———Return ............................................................ 135

———Printing Service ............................................ 157 ———Print-to-Print - Administration Screen ....... 163 ———Print Service - Administration Screen ...... 160 ———Print Service Screen ................................... 158 ———Print-to-Print Screen.................................... 163 ———Print-to-Print Service ................................... 163 ———System .......................................................... 164 ———System - Administration Screen ................ 164 ———View and Order Screen .............................. 159 ———Writing Screen.............................................. 161 ———Writing Service - Administration Screen .. 162 Optional Software Setting ...................................... 129 ———Brows............................................................. 129 ———Cancel ........................................................... 129 ———Help................................................................ 129 ———Icon ................................................................ 129 ———OK .................................................................. 129 ———Path for the Optional Software .................. 129 Order Condition Settings Screen .......................... 103 ———Condition ....................................................... 103 ———ID .................................................................... 103 ———Order No. ...................................................... 103 ———Sort No. ......................................................... 103 ———Work Select .................................................. 103

New Features ............................................................... 6

O Operating Digital Photo Center (DPC) Operation .................................. 138 Operating Digital Reorder Service ........................ 143 Operational Safety and Use Conditions ................... 9 Operation Screens and Function Key List ........... 157 ———COS Print Service Screen.......................... 158 ———Data Writing Service ................................... 161 ———DPOF Print Service Screen ....................... 159 ———Image List Screen........................................ 161 ———Printing Screen ............................................ 157

P Printing in FRONTIER .............................................. 36 ———FRONTIER 330/340 ...................................... 39 ———FRONTIER 350/370/390 .............................. 36 Printing Screen .......................................................... 20 ———[EXIT] icon ...................................................... 20

167

———[Printing] icon.................................................. 20 ———[System] icon .................................................. 20 ———[Writing] icon ................................................... 20 ———Admin .............................................................. 20 ———Automatic ........................................................ 20 ———Express ........................................................... 21 ———Help.................................................................. 20 ———Hold.................................................................. 21 ———Info ................................................................... 21 ———INPUT .............................................................. 21 ———Order Number ................................................ 20 ———Order Registration Status Display............... 22 ———OUTPUT ......................................................... 21 ———Print Q’ty ......................................................... 20

R

———Print Size ......................................................... 20 ———Recover ........................................................... 21 ———Reprint ............................................................. 21 ———Trash................................................................ 21 ———Version Display .............................................. 22 Printing Screen (in use of Multiple Service) ........ 133 ———OUTPUT ....................................................... 133 ———INPUT ............................................................ 133 Print-to-Print ............................................................... 83 Print-to-Print Procedures .......................................... 85 Print-to-Print Service Screen ................................... 83 ———Color Balance Adjustment............................ 84 ———Help.................................................................. 83 ———Add Image to Order ....................................... 84 ———Order Regist. .................................................. 84 ———Admin. ............................................................. 83 ———Apply ................................................................ 84 ———Cancel Order .................................................. 84 ———Fine Scan ........................................................ 84 ———Instax ............................................................... 83 ———Order Number ................................................ 83 ———Output Device ................................................ 83 ———Print Quantity.................................................. 83 ———Print Size ......................................................... 83 ———Return .............................................................. 84 ———Scan ................................................................. 83 ———TWAIN Source/Scanner Type ..................... 83 ———Without Margin ............................................... 83 Procedures for Changing Settings .................. 40, 65, 75, 90, 126

———Set .................................................................. 130 Setup for Digital Photo Center ............................... 151 Shutting Down Imaging Controller .......................... 23 Special Operations .................................................. 119 Starting Up and Shutting Down ............................... 18 Starting Up Imaging Controller ................................ 18

168

Registering of Digital Reorder Service into Multiple Service ......................................... 156

S Service Composition ............................................... 131 Service Type Setting ............................................... 130 ———Image Size (Base) ....................................... 130 ———Delete ............................................................ 130 ———File Format.................................................... 130 ———Help................................................................ 130 ———Media Type ................................................... 130 ———Return ............................................................ 130 ———Service Name ............................................... 130

T To cancel the COS Print Service screen ............... 59 To cancel the “DPOF Print Service” screen .......... 64

U Using of Branch Store Connection ....................... 141 Using of LAN Connection ....................................... 139

V View and Order Screen ............................................ 34 ———All/Order .......................................................... 34 ———Auto Correction .............................................. 34 ———CMYD Setting ................................................ 34 ———File Name........................................................ 34 ———Page/Order ..................................................... 34 ———Print Q’ty Setting ............................................ 34 ———Scene Correction ........................................... 34 ———Sharpness ....................................................... 34

W Writing from DSC/Media ......................................... 109 Writing Procedures .................................................. 104 Writing Service Main Screen ................................... 94 ———Add ↔ New .................................................... 94

———Connected Devices ....................................... 94 ———Copy ................................................................ 94 ———Digital Reorder ............................................... 95 ———Execution ........................................................ 95 ———Help.................................................................. 94 ———Index ................................................................ 94 ———Order Number ................................................ 94

———Admin .............................................................. 94 ———Order Registration Status ............................. 95 ———Output Drive ................................................... 94 ———Recover ........................................................... 94 ———Repair .............................................................. 95 ———Trash................................................................ 95 ———VErsion Display.............................................. 95

169

FAX ; 81-3-5484-0454 E-mail ; [email protected]

Request for Feedback Fujifilm’s Technical Division Photo Products Marketing would be most grateful if you would make copies of this form, then complete and send this to us by FAX or E-mail. Your opinions will contribute greatly to an accurate assessment of the overall quality of this manual. All questions can be answered by ticking [✓] the appropriate box(es), but in addition to these answers, please provide us with your written comments in the lined spaces following each block of questions.

< Questionnaire > Title : FRONTIER 330/340/350/370/390 DI Print/Data Writing Service Software Ver.5.0 Instruction Manual (Basic Operation Instructions) Reference Number : PP3-B1001E

Manual Title and Reference Number

Name :

Your Name and Company

Company : E-mail Address :

Your E-mail Address and FAX Number

Question 1

Question 2

•

FAX Number :

How would you rate this manual overall? (1) Very thorough

(2) Good

(3) Slightly substandard

(4) Substandard

•

If you have ticked (3) or (4), please give us your reasons.

•

Have you found any technical errors, errors in spelling, or missing words in this manual? Yes

Question 3

No

•

If you have ticked (Yes), please let us know what these errors and missing words are.

•

How would you rate the writing (language, choice of words/phrases, etc.) and the illustrations/ diagrams, etc.? (1) Clear and easy to follow

(2) Should be simplified

(3) Difficult to follow (1)’ [Illustrations, etc.] Of adequate size (2)’ [Illustrations, etc.] Too small (3)’ [Illustrations, etc.] Difficult to follow •

If you have ticked (2), (3) or (3)’, please give us your reasons.

Additional Comments/ Requests

Please return this questionnaire to : Or to this address :

FAX No. : Tokyo 81-3-5484-0454, E-mail address : [email protected]

FUJI PHOTO FILM CO., LTD. 26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.

in North America

FUJI PHOTO FILM U.S.A., INC. 200 Summit Lake Drive, Valhalla, New York 10595-1356, U.S.A.

FUJI PHOTO FILM CANADA INC. 600 Suffolk Court, Mississauga, Ontario, L5R 4G4, Canada

FUJI PHOTO FILM HAWAII, INC. 94-468 Akoki Street, Waipahu, Hawaii 96797, U.S.A.

in Europe

FUJI PHOTO FILM (EUROPE) G.m.b.H. Heesenstrasse 31, 40549 Dusseldorf, Germany

FUJI PHOTO FILM (U.K.) LTD. Fuji Film House, 125 Finchley Road, Swiss Cottage, London NW3 6HY, U.K.

FUJIFILM ESPAÑA, S.A. Aragon, 180, 08011-Barcelona, Spain

FUJIFILM FRANCE SAS Parc d' Activites du Pas-du-Lac-2, Avenue Franklin, 78186 St. Quentin en Yvelines Cedex, France

in South America

FUJI PHOTO FILM DO BRASIL LTDA. Avenida Vereador Jose Diniz, No. 3400, Campo Belo, São Paulo CEP 04604-901, Cx. Postal 3656, Brazil

in Asia

FUJI PHOTO FILM CO., LTD., HONG KONG OFFICE Room 2208, Tower 6, The Gateway Harbour City, 9 Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong

FUJIFILM REGIONAL SERVICES (SINGAPORE) PTE. LTD. 10 New Industrial Road, Fujifilm Building, Singapore 536201

FUJI PHOTO FILM (THAILAND) LTD. S.P. Building, 8th Floor, 388 Phaholyothin Road, Bangkok 10400, Thailand

FUJI PHOTO FILM (MALAYSIA) SDN. BHD. Letter Box 3, 3rd Floor Office Block 1, Crystal Plaza Lot 4, Jalan 51A/223 46100 Petaling Jaya Selangor Darul Ehsan Malaysia

FUJI PHOTO FILM CO., LTD., TAIPEI OFFICE Rm. 601, Hung Chong Bldg., No. 38, Sec. 6, Min Chuan E. Road, Taipei 11453, Taiwan

FUJI PHOTO FILM CO., LTD., SEOUL OFFICE 505-19, Kasan-Dong, Kumchon-Gu, Seoul, Korea 152-020

FUJI PHOTO FILM CO., LTD., BEIJING REPRESENTATIVE OFFICE Beijing Fortune Bldg. No. 817, 5, Dong Sanhuan Bei-lu, Chaoyang District, Beijing, China 100004

FUJI PHOTO FILM CO., LTD., HO CHI MINH OFFICE 7th Floor Sun Wah Tower, 115 Nguyen Hue Street, Dist. 01, Ho Chi Minh City, Vietnam

FUJI PHOTO FILM CO., LTD., NEW DELHI OFFICE Le Meridien Commercial Tower 8F, Janpath, New Delhi 110001, India

FUJI PHOTO FILM CO., LTD. MANILA OFFICE c/o YKL Development & Trading Corporation, 24 Sto. Domingo St., Quezon City, Metro Manila, Philippines

in Oceania

FUJI PHOTO FILM CO., LTD., SYDNEY REPRESENTATIVE OFFICE c/o Hanimex Pty. Limited, 114 Old Pittwater Road, Brookvale, N.S.W. 2100, Australia

in the Middle East FUJI PHOTO FILM CO., LTD., DUBAI OFFICE No. 14, L.O.B. No. 4, P.O.Box 17212, Jebel Ali, Dubai, U.A.E.

Printed on Recycled Paper Ref.No.PP3-B1001E TD-03.11-FG Printed in Japan

Fuji Frontier 330-340-350-370-390 - Di Print-data Writing Service Software Ver.5.0 First Edition Rulit Net 158097

Recommend Documents