Technical data on the vehicle Make Model Year Engine Variant
Nissan Terrano ll 2,7 TD 4WD 1991-1996 TD27T
Date: 03-06-2011 Owner Registration No. VIN 1. Reg. Date Data
Technical item Engine Engine ID code
TD27T
Number of cylinders
R4
Number of valves
8, OHV
Capacity/ (bore/ stroke)
2663 cm³ (96,0/ 92,0)
Compression ratio
21,9 ± 0,2: 1
Max. output kW (din hp)/ rpm
73 (100)/ 4000
Max. torque NM/ rpm
220/ 2200
Engine code location
Left side front on the edge at the cylinder head
Vehicle Identification Number location
Under the right front door on the frame side rail
Vehicle identification plate location
Left side engine bay on the scuttle panel
Valve clearance, inlet (cold/ hot)
0,25 warm
i
Valve clearance, exhaust (cold/ hot)
0,25 warm
i
Valve angle/ seat angle
45° - 45° 30'/ 45°
Piston height over block, mm
Max. 0.368 = Head gasket 1.2 ± 0.05 mm
i
Valve height in cylinder head, mm
Intake ÷ 0.79 - ÷ 1.19 Exhaust ÷ 0.80 - ÷ 1.20
i
Compression pressure, bar
29.4 (Min. 24.5) Max. difference 2.9
Oil pressure/ rpm, bar
Min. 0.78/ idle speed (Min. 2.94/ 3000)
Turbo boost pressure, bar
Max. 0,84 - 0,89
Radiator cap, bar/ thermostat °C
0,78 - 0,98/ 82° C
Clutch freeplay, mm
1.0 - 3.0/ 210 - 215 at pedal
Timing gear:
(Gear wheel drive)
i
i i i
Drive belt
Engine management Diagnostic Diagnostic connector
Left side under dashboard at A - door post
Pump/ pump type
Bosch VG distributor pump Kiki 16700-OF002 16700-OF002
Crank position °/ engine piston, mm
0° ± 1° before TDC/
Pump position, mm
0,38 ± 0,02
i
Adjustment method
Dial micrometer/ Notch
i
Injector opening pressure, new, bar
103,0 - 122,8
Injector opening pressure, used, bar
98,1 - 103,0
Injection order
1 - 3 - 4 - 2 (Cylinder 1 at timing gear)
Injection timing mark location
Belt pulley
i
Electrical system Battery
2 x 12 V/ 65 Ah
Starter motor current (cranking), A
Mitsubishi/ 50 - 75 A/ 3000 - 4000 rpm
Voltage relay, Volt at/ amp.
14,1 - 14,7/
i
Terminal definitions DIN 72 552 Alternator max, A
87 A/ 5000 rpm
Glow plug voltage/ drop resistor
Approx. 0.65 ohm
Wheel alignment Load
Full tank
Toe-in, °
0° 20' ± 05'
Camber°
0° 30' ± 30'
i
Caster°
1° 35' ± 30'
i
KPI/SAI°
12° 37'
Toe-out on turns, inner wheel°
34° 27'
Toe-out on turns, outer wheel°
33° 38'
Data
Technical item Wheel alignment Rear camber°
No factory setting
Rear toe-in °
No factory setting
Tyre size
235/ 75 R 15
Tyre pressure, front/ rear, bar
See sticker left B-doorpost
Free play in suspension parts
Factory data
Track-rod end ball joint, mm
Axial 0 - 0,2/ radial 0
i
i
Tightening torques Tightening, NM
Torque standards
Cylinder head bolts, stage 1, Nm
39 - 44 Nm oiled
Cylinder head bolts, stage 2, Nm
54 - 59 Nm
Cylinder head bolts, stage 3, Nm
+ 90° ± 10°
Cylinder head bolts, stage 4, Nm
(Max. distortion 0.2 mm)
Cylinder head bolts, stage 5, Nm
(No retightening)
Main bearings, Nm
167 - 177 step-by-step
Connection rod bearings, Nm
78 - 83
Flywheel, Nm
147 - 167
Crankshaft pulley/ vibration damp. Nm
294 - 324/
Camshaft pulley/ bearings, Nm
44 - 49/ (Rocker arm assembly 20 - 25 Nm)
Pump pulley/ idle wheel, Nm
59 - 69/
Nozzle retainer/ Nozzle in cylinder head
29 - 49/ 54 - 64
Glow plug
15 - 20
Wheel nuts/ bolts, Nm
118 - 147
Wheel hub, front/ rear, Nm
78 - 98 + loosen bolts + 0.5 - 1.5/
i
i
i
Brakes Front, min. thickness (new)
24,0 mm (26,0 mm)
Rear, min. thickness (new)
255,5 mm (254,0 mm)
Capacities Engine Engine oil/ - incl. filter, litre
6,5/ 7,4 (SAE 10W40)
Manual transmission, litre
3,5 (5 gear) (SAE 80W)
i
Final drive, litre
Front 1.3 (SAE 90) Rear 2.8 (SA E 80W/ 90)
i
Power steering, litre
1,0 (Dexron)
Cooling system, litre
10,0
A/C fluid, type/ gram
R134a/ 750 ± 50
A/C oil, type/ cm³
Nissan Type R PAG/ 200
Environmental parametres Idle speed, rpm
750 ± 50
Max rpm (exhaust test)
5050 ± 100
i
Remarks
n
n nn
Order No.: Mechanic
