DSON(GBSS19.0_01)

GSM BSS GBSS19.0

DSON Feature Parameter Description Issue

01

Date

2016-09-05

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2017. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd. Address:

Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China

Website:

http://www.huawei.com

Email:

[email protected]

Issue 01 (2016-09-05)

Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

i

GSM BSS DSON Feature Parameter Description

Contents

Contents 1 About This Document.................................................................................................................. 1 1.1 Scope.............................................................................................................................................................................. 1 1.2 Intended Audience.......................................................................................................................................................... 1 1.3 Change History............................................................................................................................................................... 1

2 Overview......................................................................................................................................... 3 2.1 Background.....................................................................................................................................................................3 2.2 Introduction.................................................................................................................................................................... 3 2.3 Benefits........................................................................................................................................................................... 4

3 Technical Description...................................................................................................................5 3.1 GBFD-171213 Automatic Paging Overload Control..................................................................................................... 5 3.1.1 Introduction................................................................................................................................................................. 5 3.1.2 Principles..................................................................................................................................................................... 5 3.2 GBFD-171215 Automatic TCH Congestion Control..................................................................................................... 8 3.2.1 Introduction................................................................................................................................................................. 8 3.2.2 Principles..................................................................................................................................................................... 8 3.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment................................................................................ 18 3.3.1 Introduction............................................................................................................................................................... 18 3.3.2 Principles................................................................................................................................................................... 18 3.4 Supplementary DSON Information.............................................................................................................................. 19

4 Related Features...........................................................................................................................21 4.1 GBFD-171213 Automatic Paging Overload Control................................................................................................... 21 4.2 GBFD-171215 Automatic TCH Congestion Control................................................................................................... 22 4.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment................................................................................ 23

5 Impact on the Network...............................................................................................................25 5.1 GBFD-171213 Automatic Paging Overload Control................................................................................................... 26 5.1.1 Impact on System Capacity....................................................................................................................................... 26 5.1.2 Impact on Network Performance...............................................................................................................................26 5.2 GBFD-171215 Automatic TCH Congestion Control................................................................................................... 26 5.2.1 Impact on System Capacity....................................................................................................................................... 26 5.2.2 Impact on Network Performance...............................................................................................................................26 5.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment................................................................................ 26 5.3.1 Impact on System Capacity....................................................................................................................................... 26 Issue 01 (2016-09-05)


ii


Contents

5.3.2 Network Performance................................................................................................................................................26

6 Engineering Guidelines............................................................................................................. 28 6.1 GBFD-171213 Automatic Paging Overload Control................................................................................................... 28 6.1.1 When to Use Automatic Paging Overload Control................................................................................................... 28 6.1.2 Information to Be Collected...................................................................................................................................... 28 6.1.3 Network Planning...................................................................................................................................................... 28 6.1.4 Deployment............................................................................................................................................................... 29 6.1.4.1 Requirements.......................................................................................................................................................... 29 6.1.4.2 Data Preparation..................................................................................................................................................... 30 6.1.4.3 Activation............................................................................................................................................................... 31 6.1.4.4 Activation Observation...........................................................................................................................................32 6.1.4.5 Deactivation............................................................................................................................................................34 6.1.5 Performance Monitoring............................................................................................................................................35 6.1.6 Parameter Optimization............................................................................................................................................. 35 6.1.7 Troubleshooting......................................................................................................................................................... 35 6.2 GBFD-171215 Automatic TCH Congestion Control................................................................................................... 35 6.2.1 When to Use Automatic TCH Congestion Control................................................................................................... 35 6.2.2 Information to Be Collected...................................................................................................................................... 36 6.2.3 Network Planning...................................................................................................................................................... 36 6.2.4 Deployment............................................................................................................................................................... 36 6.2.4.1 Requirements.......................................................................................................................................................... 36 6.2.4.2 Data Preparation..................................................................................................................................................... 37 6.2.4.3 Activation............................................................................................................................................................... 37 6.2.4.4 Activation Observation...........................................................................................................................................38 6.2.4.5 Deactivation............................................................................................................................................................39 6.2.5 Performance Monitoring............................................................................................................................................40 6.2.6 Parameter Optimization............................................................................................................................................. 41 6.2.7 Troubleshooting......................................................................................................................................................... 41 6.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment................................................................................ 41 6.3.1 When to Use Adaptive Scenario-based Parameter Adjustment................................................................................ 41 6.3.2 Information to Be Collected...................................................................................................................................... 41 6.3.3 Planning..................................................................................................................................................................... 41 6.3.4 Deployment............................................................................................................................................................... 42 6.3.4.1 Requirements.......................................................................................................................................................... 42 6.3.4.2 Data Preparation..................................................................................................................................................... 42 6.3.4.3 Activation............................................................................................................................................................... 43 6.3.4.4 Activation Observation...........................................................................................................................................44 6.3.4.5 Deactivation............................................................................................................................................................45 6.3.5 Performance Monitoring............................................................................................................................................46 6.3.6 Parameter Optimization............................................................................................................................................. 46 6.3.7 Troubleshooting......................................................................................................................................................... 46

7 Parameters..................................................................................................................................... 47 Issue 01 (2016-09-05)


iii


Contents

8 Counters........................................................................................................................................ 95 9 Glossary......................................................................................................................................... 96 10 Reference Documents............................................................................................................... 97

Issue 01 (2016-09-05)


iv


1 About This Document

1

About This Document

1.1 Scope This document describes Huawei GBSS Distributed Self-Organizing Network (DSON), including its technical principles, related features, network impact, and engineering guidelines. This document covers the following features: l

GBFD-171213 Automatic Paging Overload Control

l

GBFD-171215 Automatic TCH Congestion Control

l

GBFD-180205 Adaptive Scenario-based Parameter Adjustment

1.2 Intended Audience This document is intended for: l

Personnel who need to understand the DSON feature

l

Personnel who work with Huawei GSM products

1.3 Change History This section provides information about the changes in different document versions. There are two types of changes: l

Feature change Changes in features of a specific product version.

l

Editorial change Changes in wording or addition of information and any related parameters affected by editorial changes.

01 (2016-09-05) This issue does not include any changes. Issue 01 (2016-09-05)


1


1 About This Document

Draft A (2016-06-30) Compared with Issue 01 (2016-02-29) of GBSS18.1, Draft A (2016-06-30) of GBSS19.0 includes the following changes.

Issue 01 (2016-09-05)

Change Type

Change Description

Parameter Change

Feature change

None

None

Editorial change

Updated the requirements for BTS deployment. For details, see 6.1.4.1 Requirements.

None


2


2 Overview

2

Overview

2.1 Background After decades of development, GSM networks have grown to accommodate a large number of features and parameters. These parameters must be adjusted properly on different networks in accordance with different network plans and traffic volumes. Due to the network complexity, the parameters sometimes are set to inappropriate values. The inappropriate parameters may cause performance problems. DSON optimizes configurations in the following scenarios: When certain unplanned events, such as parades or other mass gatherings occur, traffic increases sharply. In such traffic burst scenarios, users cannot optimize their network configuration in advance to avoid network congestion. Network congestion may occur at any time. In this case, DSON can automatically identify congestion scenarios and implement corresponding operations to eliminate the congestion. Inappropriate parameter settings deteriorate network performance if congestion occurs in any of the following scenarios: concentric cells, half-rate voice services, paging, and satellite transmission over the Abis interface. DSON can automatically identify these scenarios, and check and adjust parameters accordingly.

2.2 Introduction DSON covers the following features: l

GBFD-171213 Automatic Paging Overload Control This feature enables BSCs to monitor the paging status on the network in real time. When network paging exceeds certain thresholds, the BSCs automatically activate related functions, algorithms or adjust related parameters to relieve the paging overload and improve network performance.

l

GBFD-171215 Automatic TCH Congestion Control This feature enables BSCs to monitor the loads on traffic channels (TCHs) on the network in real time. When the TCH loads exceed certain thresholds, the BSCs automatically activate related functions, algorithms or adjust related parameters to relieve TCH congestion and improve network performance.

Issue 01 (2016-09-05)


3


l

2 Overview

GBFD-180205 Adaptive Scenario-based Parameter Adjustment This feature enables BSCs to periodically inspect network scenario characteristics and perform parameter checks. When identifying inappropriate parameter settings in the concentric cell, half-rate speech version, paging, or satellite transmission over Abis scenario, the BSCs adaptively adjust the parameter settings to the network scenarios. In this way, this feature prevents inappropriate parameter settings from affecting network performance.

2.3 Benefits DSON automatically identifies paging overload and TCH congestion and implements corresponding operations to resolve theses problems. Alternatively, DSON adjusts parameters in certain scenarios to achieve optimal network performance. In this way, network operation and maintenance work is simplified for customers, reducing the OPEX and improving system stability.

Issue 01 (2016-09-05)


4


3 Technical Description

3

Technical Description

3.1 GBFD-171213 Automatic Paging Overload Control 3.1.1 Introduction This feature enables BSCs to monitor the paging status on the network in real time. When paging overloads exceed certain thresholds, the BSCs automatically adjust the parameters of the following paging-related features to improve network performance: l

CS Layered Paging

l

Layered Paging

l

Dynamic Multiple CCCH

3.1.2 Principles This feature takes effect when PagingOvldCtrlStThld(BSC6900,BSC6910) is set to a value other than 255. In such a case, BSCLayeredPagingSW(BSC6900,BSC6910) is automatically set to ON(On) and the BSC adjusts paging-related parameters according to control levels.

Issue 01 (2016-09-05)


5



Current Level

Event

Target Level

Parameter Adjustment

Level 0

1. The BSC checks the CCCH load every five seconds.

Level 1

1. Set PSPagingCtrl(BSC6900,BS C6910) to FIRSTPRECISEPAGING(First precise paging).

2. If the following condition is met 8 out of 12 times, the control level must be changed: For more than 30% of the paging groups in a cell, the load on each paging group is equal to or greater than PagingOvldCtrlStThld(BS C6900,BSC6910).

2. Set CSPagingCtrl(BSC6900,BS C6910) to FIRSTPRECISEPAGING(First precise paging). 3. Set IMMOccupyPCHOptSw(BS C6900,BSC6910) to ON(On). 4. NOTE This parameter does not apply to eGBTSs.

4. Set TBFASSADJSW(BSC6900, BSC6910) to ON(ON). Level 1


Level 0

2. If the following condition is met 16 out of 20 times, the control level must be changed: For more than 85% of the paging groups in a cell, the load on each paging group is less than the calculation result of the following formula: PagingOvldCtrlStThld(BS C6900,BSC6910) x 20%

1. Set PSPagingCtrl(BSC6900,BS C6910) to ALWAYSNORMALPAGING(Always normal paging). 2. Set CSPagingCtrl(BSC6900,BS C6910) to ALWAYSNORMALPAGING(Always normal paging). 3. Restore IMMOccupyPCHOptSw(BS C6900,BSC6910) to its initial setting. 4. Restore TBFASSADJSW(BSC6900, BSC6910) to its initial setting.

Issue 01 (2016-09-05)


6


Current Level


Event

Target Level



Level 2

1. Set DynCCCHSwitch(BSC6900 ,BSC6910) to ON(ON).

2. If the following condition is met 8 out of 12 times, the control level must be changed: For more than 30% of the paging groups in a cell, the load on each paging group is greater than the calculation result of the following formula: min( PagingOvldCtrlStThl d(BSC6900,BSC6910) + 10%,95%)

2. Set DynCCCHLoadIncrThr(BS C6900,BSC6910) to the calculation result of the following formula: min( PagingOvldCtrlStThl d(BSC6900,BSC6910) + 10%,initial setting of DynCCCHLoadIncrThr(BS C6900,BSC6910),95%) 3. Set DynCCCHLoadRedcThr(B SC6900,BSC6910) to the calculation result of the following formula: DynCCCHLoadIncrThr(BS C6900,BSC6910) after adjustment – 25% (If the calculation result is a negative value, set this parameter to 0.) When DynCCCHLoadRedcThr(B SC6900,BSC6910) is set to 0, set DynCCCHLoadIncrThr(BS C6900,BSC6910) and DynCCCHLoadRedcThr(B SC6900,BSC6910) to their manually configured settings. 4. Set DynCCCHLoadDuration(BSC6900,BSC6910) to 1. 5. Set MaxDynCCCHNum(BSC6 900,BSC6910) to 3. 6. Set DynCCCHReduceInterval(BSC6900,BSC6910) to 10.

Issue 01 (2016-09-05)


7



Current Level

Event

Target Level


Level 2


Level 1

Restore the following parameters to their initial settings:

2. If the following conditions are met 16 out of 20 times, the control level must be changed: a. For more than 85% of the paging groups in a cell, the load on each paging group is less than the calculation result of the following formula: min( PagingOvldCtrlStT hld(BSC6900,BSC6910) + 10%,95%) – 10% b. The current number of CCCH timeslots is less than or equal to the initial number of CCCH timeslots.

1. DynCCCHSwitch(BSC6900 ,BSC6910) 2. DynCCCHLoadIncrThr(BS C6900,BSC6910) 3. DynCCCHLoadRedcThr(B SC6900,BSC6910) 4. DynCCCHLoadDuration(BSC6900,BSC6910) 5. MaxDynCCCHNum(BSC6 900,BSC6910) 6. DynCCCHReduceInterval(BSC6900,BSC6910)

3.2 GBFD-171215 Automatic TCH Congestion Control 3.2.1 Introduction This feature enables BSCs to monitor the loads on TCHs on the network in real time. When the loads on the TCHs exceed certain thresholds, the BSCs automatically activate related functions, or adjust related parameters to relieve TCH congestion, thereby improving network performance. These functions include TCHF-TCHH handover, inter-cell handover, and directed retry. These parameters include TCH Traffic Busy Threshold and AMR TCH/H Prior Cell Load Threshold.

3.2.2 Principles This feature takes effect when TCHCongCtrlStThld(BSC6900,BSC6910) is set to a value other than 255. In such a case, the BSC adjusts related parameters based on control levels.

Issue 01 (2016-09-05)


8



Current Level

Event

Target Level


Level 0

1. The BSC checks the TCH load every second.

Level 0

Restore all parameters of the Automatic TCH Congestion Control feature to their manually configured settings.

2. If the following condition is met 240 out of 300 times, the control level remains unchanged: The TCH load of a cell is less than 30%.

Issue 01 (2016-09-05)


9


Current Level


Event

Target Level



Level 1

1. Set ALLOWHALFRATEUSER PERC(BSC6900,BSC6910) to 100.

2. If the following condition is met 40 out of 60 times, the control level must be changed: The TCH load of a cell is greater than TCHCongCtrlStThld(BSC6 900,BSC6910).

2. Set ALLOWAMRHALFRATE USERPERC(BSC6900,BS C6910) to 100. 3. Set AMRTCHHPRIORALLO W(BSC6900,BSC6910) to ON(On). 4. Set AMRTCHHPRIORLOAD( BSC6900,BSC6910) to min( TCHBUSYTHRES(B SC6900,BSC6910), initial setting of AMRTCHHPRIORLOAD( BSC6900,BSC6910) ) For a cell using Huawei I handover algorithm, modify parameter settings as follows: 5. Set INTRACELLFHHOEN(B SC6900,BSC6910) to HOBASECAPANDQUA L(HOBASECAPANDQU AL). 6. Set AMRFULLTOHALFHOA LLOW(BSC6900,BSC6910 ) to YES(Yes). 7. Set NOAMRFULLTOHALFHOALLOW(BSC6900,BSC 6910) to YES(Yes). 8. Set AMRHALFTOFULLHOQUALALLOW(BSC6900,B SC6910) to NO(No). 9. Set NOAMRHALFTOFULLHOQUALALLOW(BSC69 00,BSC6910) to NO(No). 10. Set AMRFULLTOHALFHO-

Issue 01 (2016-09-05)


10


Current Level


Event

Target Level

Parameter Adjustment THRESH(BSC6900,BSC6 910) to the calculation result of the following formula: min( TCHCongCtrlStThld( BSC6900,BSC6910),initial setting of AMRFULLTOHALFHOTHRESH(BSC6900,BSC6 910) ) 11. Set NOAMRFULLTOHALFTHRESH(BSC6900,BSC6 910) to the calculation result of the following formula: min( TCHCongCtrlStThld( BSC6900,BSC6910),initial setting of NOAMRFULLTOHALFTHRESH(BSC6900,BSC6 910) ) For a cell using Huawei II handover algorithm, modify parameter settings as follows: 5. Set INTRACELLHOEN(BSC6900 ,BSC6910) to YES(Yes). 6. Set AMRFULLTOHALFHOALLOW(BSC6900,BSC6910) to YES(Yes). 7. Set NOAMRFULLTOHALFHOALLOW(BSC6900,BSC69 10) to YES(Yes). 8. Set AMRHALFTOFULLHOQUALALLOW(BSC6900,BSC 6910) to NO(No). 9. Set NOAMRHALFTOFULLHOQUALALLOW(BSC6900,BSC 6910) to NO(No). 10. Set AMRFULLTOHALFHOTHRESH(BSC6900,BSC6910)

Issue 01 (2016-09-05)


11


Current Level


Event

Target Level

Parameter Adjustment to the calculation result of the following formula: min( TCHCongCtrlStThld(BS C6900,BSC6910),manually configured setting of AMRFULLTOHALFHOTHRESH(BSC6900,BSC6910) ) 11. Set NOAMRFULLTOHALFTHRESH(BSC6900,BSC6910) to the calculation result of the following formula: min( TCHCongCtrlStThld(BS C6900,BSC6910),initial setting of NOAMRFULLTOHALFTHRESH(BSC6900,BSC6910) )

Issue 01 (2016-09-05)


12



Current Level

Event

Target Level


Level 1


Level 0

Restore the following parameters to their manually configured settings:

2. If the following condition is met 240 out of 300 times, the control level remains unchanged: The TCH load of a cell is less than the calculation result of the following formula: TCHCongCtrlStThld(BSC6 900,BSC6910) – 10%

1. ALLOWHALFRATEUSER PERC(BSC6900,BSC6910) 2. ALLOWAMRHALFRATE USERPERC(BSC6900,BS C6910) 3. AMRTCHHPRIORALLO W(BSC6900,BSC6910) For a cell using Huawei I handover algorithm, modify parameter settings as follows: 4. INTRACELLFHHOEN(B SC6900,BSC6910) 5. AMRFULLTOHALFHOA LLOW(BSC6900,BSC6910 ) 6. NOAMRFULLTOHALFHOALLOW(BSC6900,BSC 6910) 7. AMRHALFTOFULLHOQUALALLOW(BSC6900,B SC6910) 8. NOAMRHALFTOFULLHOQUALALLOW(BSC69 00,BSC6910) 9. AMRFULLTOHALFHOTHRESH(BSC6900,BSC6 910) 10. NOAMRFULLTOHALFTHRESH(BSC6900,BSC6 910) For a cell using Huawei II handover algorithm, modify parameter settings as follows: 4. INTRACELLHOEN(BSC6900 ,BSC6910) 5. AMRFULLTOHALFHOALLOW(BSC6900,BSC6910) 6. NOAMRFULLTOHALFHOALLOW(BSC6900,BSC69 10)

Issue 01 (2016-09-05)


13


Current Level


Event

Target Level

Parameter Adjustment 7. AMRHALFTOFULLHOQUALALLOW(BSC6900,BSC 6910) 8. NOAMRHALFTOFULLHOQUALALLOW(BSC6900, BSC6910) 9. AMRFULLTOHALFHOTHRESH(BSC6900,BSC6910) 10. NOAMRFULLTOHALFTHRESH(BSC6900,BSC6910)


Level 2

2. If the following condition is met 40 out of 60 times, the control level must be changed: The TCH load of a cell is greater than the calculation result of the following formula: (90% + TCHCongCtrlStThld(BSC6 900,BSC6910) )/2

1. Set LoadHoEn(BSC6900,BSC 6910) to YES(Yes). 2. Set TRIGTHRES(BSC6900,BS C6910) to the calculation result of the following formula: min( TCHCongCtrlStThld( BSC6900,BSC6910) + (90% – TCHCongCtrlStThld(BSC6 900,BSC6910) )/2,initial setting of TRIGTHRES(BSC6900,BS C6910) ) 3. Set LoadAccThres(BSC6900,B SC6910) to the calculation result of the following formula: TRIGTHRES(BSC6900,BS C6910) after adjustment – 10 (If the calculation result is a negative value, set this parameter to 0.) 4. Set LOADHOPERIOD(BSC69 00,BSC6910) to 1. 5. Set LOADHOSTEP(BSC6900, BSC6910) to the manually configured setting of LOADOFFSET(BSC6900, BSC6910).

Issue 01 (2016-09-05)


14



Current Level

Event

Target Level


Level 2


Level 1


2. If the following condition is met 240 out of 300 times, the control level remains unchanged: The TCH load of a cell is less than the calculation result of the following formula: ( TCHCongCtrlStThld(BSC 6900,BSC6910) + (90 – TCHCongCtrlStThld(BSC6 900,BSC6910) )/2) – 10%

Issue 01 (2016-09-05)


1. LoadHoEn(BSC6900,BSC 6910) 2. LoadAccThres(BSC6900,B SC6910) 3. TRIGTHRES(BSC6900,BS C6910) 4. LOADHOPERIOD(BSC69 00,BSC6910) 5. LOADHOSTEP(BSC6900, BSC6910)

15


Current Level


Event

Target Level



Level 3

1. Set AMRFULLTOHALFHOQUALTHRESH(BSC6900, BSC6910) to the calculation result of the following formula: max(initial setting of AMRFULLTOHALFHOQUALTHRESH(BSC6900, BSC6910),2)

2. If the following condition is met 30 out of 60 times, the control level must be changed: The TCH load of a cell is greater than 90%.

2. Set NOAMRFULLTOHALFHOQUALTHRESH(BSC6 900,BSC6910) to the calculation result of the following formula: max(initial setting of NOAMRFULLTOHALFHOQUALTHRESH(BSC6 900,BSC6910),2) For a cell using Huawei I handover algorithm, modify parameter settings as follows: 3. 3. Set LOADOFFSET(BSC6900, BSC6910) to the calculation result of the following formula: max(manually configured setting of LOADOFFSET(BSC6900, BSC6910),25) For a cell using Huawei II handover algorithm, modify parameter settings as follows: 3. 3. Set LOADOFFSET(BSC6900,BS C6910) to the calculation result of the following formula: max(manually configured setting of LOADOFFSET(BSC6900,BS C6910),8)

Issue 01 (2016-09-05)


16



Current Level

Event

Target Level


Level 3


Level 2


2. If the following condition is met 240 out of 300 times, the control level remains unchanged: The TCH load of a cell is less than 85%.

1. LOADOFFSET(BSC6900, BSC6910) 2. AMRFULLTOHALFHOQUALTHRESH(BSC6900, BSC6910) 3. NOAMRFULLTOHALFHOQUALTHRESH(BSC6 900,BSC6910)


Level 4

2. If the following condition is met 20 out of 60 times, the control level must be changed: The TCH load of a cell is greater than 95%.

Level 4


2. Set ASSLOADJUDGEEN(BS C6900,BSC6910) to ENABLE(Enable). 3. Set CDRTTRYFBDTHRES(B SC6900,BSC6910) to the calculation result of the following formula: min(95,initial setting of CDRTTRYFBDTHRES(B SC6900,BSC6910) ) Level 3

2. If the following condition is met 240 out of 300 times, the control level remains unchanged: The TCH load of a cell is greater than 90%.

Issue 01 (2016-09-05)

1. Set DIRECTRYEN(BSC6900, BSC6910) to YES(Yes).


Restore the following parameters to their manually configured settings: 1. DIRECTRYEN(BSC6900, BSC6910) 2. ASSLOADJUDGEEN(BS C6900,BSC6910) 3. CDRTTRYFBDTHRES(B SC6900,BSC6910)

17


Current Level


Event

Target Level



Level 4

1. Set TCHBUSYTHRES(BSC69 00,BSC6910) to the calculation result of the following formula: Initial setting of TCHBUSYTHRES(BSC69 00,BSC6910) x 0.5

2. If the following condition is met 120 out of 180 times, the control level remains unchanged: The TCH load of a cell is equal to 100%.

2. Set AMRTCHHPRIORLOAD( BSC6900,BSC6910) to the calculation result of the following formula: min(Initial setting of TCHBUSYTHRES(BSC69 00,BSC6910), initial setting of AMRTCHHPRIORLOAD( BSC6900,BSC6910) ) x 0.5

3.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment 3.3.1 Introduction This feature enables BSCs to periodically inspect network scenario characteristics and perform parameter checks. When identifying inappropriate parameter settings in the concentric cell, half-rate speech version, paging, or satellite transmission over Abis scenario, the BSCs adaptively adjust the parameter settings to the network scenarios. In this way, this feature prevents inappropriate parameter settings from affecting network performance.

3.3.2 Principles This feature takes effect when one or multiple options of the AutoParaAdjustSw(BSC6900,BSC6910) parameter are selected. The AutoParaAdjustSw(BSC6900,BSC6910) parameter provides the following options: IUOADJUST(Concentric Cell Adjustment), HRADJUST(Half-Rate Adjustment), PGADJUST(Paging Adjustment), and ABISSATELLITEADJUST(Abis Satellite Transmission Adjustment). The BSC identifies scenarios and adjusts parameters when the feature is enabled and in every early morning.

Concentric Cell Adjustment The Concentric Cell Adjustment function takes effect when IUOADJUST(Concentric Cell Adjustment) is selected for AutoParaAdjustSw(BSC6900,BSC6910). In such a case, the BSC checks whether a cell is a concentric cell and whether Issue 01 (2016-09-05)


18



FMSMAXOPCC(BSC6900,BSC6910) of the concentric cell is consistent with the maximum transmit power level allowed by the BCCH frequency band. When FMSMAXOPCC(BSC6900,BSC6910) is inconsistent with the maximum transmit power level, the BSC adaptively adjusts the setting of FMSMAXOPCC(BSC6900,BSC6910).

Half-Rate Adjustment The Half-Rate Adjustment function takes effect when HRADJUST(Half-Rate Adjustment) is selected for AutoParaAdjustSw(BSC6900,BSC6910). In such a case, the BSC checks whether a half-rate speech version is configured. If it is, the BSC will check the setting of TCHAJFLAG(BSC6900,BSC6910). When the setting of TCHAJFLAG(BSC6900,BSC6910) is inappropriate, the BSC automatically adjusts it.

Paging Adjustment The Paging Adjustment function takes effect when PGADJUST(Paging Adjustment) is selected for AutoParaAdjustSw(BSC6900,BSC6910). In such a case, the BSC checks and adaptively adjusts the setting of BSPAMFRAMS(BSC6900,BSC6910). Based on the settings of NMO(BSC6900,BSC6910) and GPRS(BSC6900,BSC6910), the BSC also adaptively enables or disables the BSS Paging Coordination feature by adjusting the setting of BSSPAGINGCOORDINATION(BSC6900,BSC6910).

Abis Satellite Transmission Adjustment The Abis Satellite Transmission Adjustment function takes effect when ABISSATELLITEADJUST(Abis Satellite Transmission Adjustment) is selected for AutoParaAdjustSw(BSC6900,BSC6910). In such a case, the BSC checks the setting of TransMode(BSC6900,BSC6910) to determine whether satellite transmission over Abis is used. In the satellite transmission over Abis scenario, the BSC adaptively adjusts the setting of TX(BSC6900,BSC6910).

3.4 Supplementary DSON Information Parameter Settings Parameter settings related to DSON comply with the following rules: l

When DSON is disabled, manually configured parameter settings take effect.

l

When DSON is enabled, the parameters are automatically adjusted according to the DSON implementation mechanism and the parameter settings after adjustment take effect.

l

–

If you have not modified the parameter settings, the automatically adjusted parameter settings will take effect.

–

If you have modified the parameter settings, the manually modified parameter settings will take effect. In the next adaptive adjustment period, the BSC checks the current settings and determines whether to adjust them. You are advised not to manually modify the adjusted parameters.

If you change the current scenario after the parameters have been automatically adjusted, the BSC will use the manually configured settings as the current settings.

Parameter settings exported from the LMT or queried with LST commands are all manually configured. To obtain the settings currently in effect, view the parameter adjustment log of Issue 01 (2016-09-05)


19



DSON. You can also run the following commands to query the manually configured and current settings: l

DSP GCELLSON

l

DSP BSCSON (only applicable for the Automatic Paging Overload Control feature)

l

DSP GTRXSON (only applicable for the Half-Rate Adjustment function)

Issue 01 (2016-09-05)


20


4 Related Features

4

Related Features

4.1 GBFD-171213 Automatic Paging Overload Control Prerequisite Feature None

Mutually Exclusive Feature None

Impacted Feature

Issue 01 (2016-09-05)

Feature ID

Feature Name

Description

GBFD-160204

CS Layered Paging

GBFD-511502

Layered Paging

l When the GBFD-171213 Automatic Paging Overload Control feature is enabled, the CS Layered Paging and Layered Paging features are dynamically controlled: When traffic is heavy, the Layered Paging feature is enabled to reduce paging load. When traffic is light, the Layered Paging feature is disabled to reduce paging delay. l GBFD-171213 Automatic Paging Overload Control impacts GBFD-160204 CS Layer Paging, GBFD-511502 Layered Paging, and GBFD-511503 Dynamic Multiple CCCH, which are all optional features. If you do not purchase the licenses for these features or the number of licenses is insufficient, the parameters for these features are


21


4 Related Features

Feature ID

Feature Name

GBFD-511503

Dynamic Multiple CCCH

Description skipped during the current parameter adjustment. Based on the license status, the BSC will determine whether to adjust these parameters in the next parameter adjustment. To ensure that parameters can be appropriately adjusted, purchase required licenses before using the Automatic Paging Overload Control feature. When DSON is enabled, certain optional features may be enabled or disabled after parameter adjustment. If either the manually configured setting or the current setting of a parameter indicates that an optional feature is enabled, the number of consumed licenses will be incremented by one.

4.2 GBFD-171215 Automatic TCH Congestion Control Prerequisite Feature None


Impacted Feature

Issue 01 (2016-09-05)

Feature ID

Feature/Function Name

Description

N/A

Concentric Cell

When Concentric Cell is enabled, do not enable the Automatic TCH Congestion Control feature. Otherwise, counters will fluctuate.


22


4 Related Features

Feature ID


Description

GBFD-113402

Dynamic Adjustment Between FR and HR

GBFD-171215 Automatic TCH Congestion Control impacts GBFD-113402 Dynamic Adjustment Between FR and HR, which is an optional feature. If you do not purchase the license for this feature or the number of licenses is insufficient, the parameters of this feature are skipped during the current parameter adjustment. Based on the license status, the BSC will determine whether to adjust these parameters in the next parameter adjustment. To ensure that parameters can be appropriately adjusted, purchase required licenses before using the Automatic TCH Congestion Control feature. When DSON is enabled, certain optional features may be enabled or disabled after parameter adjustment. If either the manually configured setting or the current setting of a parameter indicates that an optional feature is enabled, the number of consumed licenses will be incremented by one.

4.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment Prerequisite Feature None


Impacted Feature

Issue 01 (2016-09-05)

Feature ID


Description

GBFD-119305

BSS Paging Coordination

GBFD-180205 Adaptive Scenariobased Parameter Adjustment impacts GBFD-119305 BSS Paging Coordination, GBFD-113402 Dynamic


23


Issue 01 (2016-09-05)

4 Related Features

Feature ID


Description

GBFD-113402

Dynamic Adjustment Between FR and HR

GBFD-113901

Satellite Transmission over Abis Interface

Adjustment Between FR and HR, and GBFD-113901 Satellite Transmission over Abis Interface, which are all optional features. If you do not purchase the licenses for these features or the number of licenses is insufficient, the parameters of these features are skipped during the current parameter adjustment. Based on the license status, the BSC will determine whether to adjust these parameters in the next parameter adjustment. To ensure that parameters can be appropriately adjusted, purchase required licenses before using the Adaptive Scenariobased Parameter Adjustment feature. When DSON is enabled, certain optional features may be enabled or disabled after parameter adjustment. If either the manually configured setting or the current setting of a parameter indicates that an optional feature is enabled, the number of consumed licenses will be incremented by one.


24


5 Impact on the Network

5

Impact on the Network

This chapter describes the impact of DSON on the network. The impact of the following features related to DSON is outside the scope of this document: CS Layered Paging, Layered Paging, Dynamic Multiple CCCH, and Dynamic Adjustment Between FR and HR. For details about the impacts of these features on the network, see related feature description documents.

Issue 01 (2016-09-05)


25



5.1 GBFD-171213 Automatic Paging Overload Control 5.1.1 Impact on System Capacity In the case of paging overload, enabling this feature increases the system paging capacity.

5.1.2 Impact on Network Performance In the case of paging overload, enabling this feature reduces the value of RL3188:OVERLOAD rate of paging.

5.2 GBFD-171215 Automatic TCH Congestion Control 5.2.1 Impact on System Capacity In the case of TCH congestion, enabling this feature increases the system TCH capacity.

5.2.2 Impact on Network Performance In the case of TCH congestion, enabling this feature has the following impacts on network performance: l

Congestion caused by assignments decreases.

l

The proportion of half-rate TCHs (K3034: TCHH Traffic Volume/K3014:Traffic Volume on TCH) increases in traffic-congested cells.

l

The number of handovers (CH300:Internal Intra-Cell Handover Requests and CH310:Number of Outgoing Internal Inter-Cell Handover Requests) increases in trafficcongested cells.

l

The ZTR304:Call Drop Rate on TCH per cell(including Handover) slightly increases in traffic-congested cells.

l

Load sharing is implemented among cells, which improves the network's capability of handling traffic bursts.

5.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment 5.3.1 Impact on System Capacity When this feature is enabled and the Half-Rate Adjustment function takes effect, TCH fullrate to half-rate handovers increase the TCH capacity.

5.3.2 Network Performance This feature has the following impacts on network performance: Issue 01 (2016-09-05)


26



l

If the Concentric Cell Adjustment function takes effect, the RA333:Success Rate of Call Establishment will remain unchanged or increase, and the ZTR304:Call Drop Rate on TCH per cell(including Handover) will decrease or remain unchanged.

l

If the Half-Rate Adjustment function takes effect, the K3034:TCHH Traffic Volume will remain unchanged or increase, the K3045:Congestion Rate on TCH (All Channels Busy) will remain unchanged or decrease, and the speech quality will remain unchanged or slightly decrease.

l

If the Paging Adjustment function takes effect, the RA333:Success Rate of Call Establishment will remain unchanged or increase.

l

If the Abis Satellite Transmission Adjustment function takes effect, the RCA313: Assignment Success Rate will remain unchanged or increase.

Issue 01 (2016-09-05)


27


6 Engineering Guidelines

6

Engineering Guidelines

6.1 GBFD-171213 Automatic Paging Overload Control 6.1.1 When to Use Automatic Paging Overload Control It is recommended that this feature be used for cells meeting either of the following conditions: l

The RL3188:OVERLOAD rate of paging is greater than 0 and L3188M:Maximum Seizure Rate of PCH Paging Queue is greater than 70%.

Counter

Description

CELL.PAGING.OVERLOAD

RL3188:OVERLOAD rate of paging

CELL.FCTRL.PCH.QUE.MAX.TN

L3188M:Maximum Seizure Ratio of PCH Paging Queue

l

Certain unplanned events, such as parades or other mass gatherings may occur and result in traffic bursts.

6.1.2 Information to Be Collected None

6.1.3 Network Planning RF Planning None

Network Topology None Issue 01 (2016-09-05)


28



Hardware Planning None

6.1.4 Deployment 6.1.4.1 Requirements Table 6-1 Requirements

Issue 01 (2016-09-05)

Aspect

Requirement

Related features

For details, see 4 Related Features.

BSC

None

BTS

Only 3900 series base stations support this feature. The required BTS version must be used.

GSM networking

None

MS

None

MSC

None

License

The license control item for this feature has been activated. For details on how to activate the license, see License Management Feature Parameter Description. For details about license items, see License Control Item Description.

Others

None


29



6.1.4.2 Data Preparation Table 6-2 Data preparation Parameter Name

Parameter ID

NE

Setting Notes

Data Source

Paging Overload Control Start Threshold

PagingOvl dCtrlStThl d(BSC6900 ,BSC6910)

BSC6900/ BSC6910

This parameter specifies the load threshold for triggering the Automatic Paging Overload Control feature.

Transport network plan (internal plan)

Dynamic Channel Adjustment Policy

ChannelDy nAdjustOp t(BSC6900, BSC6910)

If this parameter is set to a value other than 255 and the PCH load in the cell reaches or exceeds the threshold specified by this parameter, the BSC performs parameter self-adjustment to reduce the PCH load. BSC6900/ BSC6910

This parameter specifies whether to enable the dynamic channel adjustment optimization procedure. If this parameter is set to ON(On), the BSC sends the BTS a message indicating dynamic channel adjustment through the RSL. If this parameter is set to OFF(Off), the BSC sends the BTS a message indicating dynamic channel adjustment through the OML.


By default, the BTS regards dynamic channel adjustment through the OML is static, and therefore the extended CCCH dynamically converted from a TCH cannot be rolled back, affecting DSON effect. To ensure a good DSON effect, set this parameter to ON(On).

Issue 01 (2016-09-05)


30



Parameter Name

Parameter ID

NE

Setting Notes

Data Source

Dynamic CCCH Addition Threshold

DynCCCH LoadIncrT hr(BSC690 0,BSC6910 )

BSC6900/ BSC6910

This parameter specifies the load threshold for dynamically converting a TCH to an extended CCCH.


If this parameter is set to 0, the Dynamic Multiple CCCH feature can only expand the capacity. In this case, the DSON control level cannot be adjusted. Set this parameter to a value greater than 0 based on the actual congestion status.

Dynamic CCCH Removal Threshold

DynCCCH LoadRedcT hr(BSC690 0,BSC6910 )

BSC6900/ BSC6910

This parameter specifies the load threshold for dynamically converting an extended CCCH to a TCH. If this parameter is set to 0, the Dynamic Multiple CCCH feature can only expand the capacity. In this case, the DSON control level cannot be adjusted.


Set this parameter to a value greater than 0 based on the actual congestion status.

6.1.4.3 Activation Using MML Commands Step 1 Run the BSC MML command SET GCELLSON with Paging Overload Control Start Threshold set to a value other than 255. Step 2 Run the BSC MML command SET BSCEXSOFTPARA with Dynamic Channel Adjustment Policy set to a value other than ON(On). ----End

MML Command Examples SET GCELLSON: IDTYPE=BYID, CELLID=1, PagingOvldCtrlStThld=80; SET BSCEXSOFTPARA: ChannelDynAdjustOpt=ON;

Issue 01 (2016-09-05)


31



Using the CME NOTE

When configuring the Automatic Paging Overload Control feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

Step 1 Configure a single object on the CME. (CME single configuration) Set the parameter described in Table 6-3 on the CME. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center) To modify objects (such as BSCs, BTSs, TRXs, GSM cells, and GSM external cells) in batches, click on the CME to start the batch modification wizard. For instructions on how to perform a batch modification through the CME batch modification center, press F1 while running the wizard to obtain online help. ----End Table 6-3 Configuring the parameter on the CME SN

MO

NE

Parameter Name

Parameter ID

Configura ble in CME Batch Modificati on Center

1

GCELLSO N

BSC6900/ BSC6910


PagingOvld CtrlStThld

Yes

2

BSCEXSO FTPARA

BSC6900/ BSC6910

Dynamic Channel Adjustment Policy

ChannelDyn AdjustOpt

Yes

6.1.4.4 Activation Observation When paging overloads occur, perform the following steps to check whether the Automatic Paging Overload Control feature has been activated: Expected result: After this feature takes effect, the paging overload rate becomes lower than before. Step 1 Run DSP commands to query the manually configured settings and the current settings of DSON parameters. 1.

Issue 01 (2016-09-05)

To query the manually configured and current settings of cell-level DSON parameters, run the BSC MML command DSP GCELLSON, select a cell, and set Query Feature Type to AUTOPAGINGOVLDCTRL(Auto Paging Overload Control). If you do not Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

32



select a cell, the cell-level DSON parameters of all cells controlled by the BSC will be queried. 2.

To query the manually configured settings and currently effective settings of BSC-level DSON parameters, run the BSC MML command DSP BSCSON.

Expected result: Cell-level and BSC-level parameters related to this feature are displayed, and the configured values and current values of the parameters are inconsistent if the adaptive parameter adjustment has taken effect. Step 2 Check the parameter adjustment log of DSON. If there are parameter adjustment records in the parameter adjustment log, the Automatic Paging Overload Control feature has been activated. Expected result: The parameters that were adaptively adjusted by this feature are displayed in the DSON log. To query the parameter adjustment log of DSON, perform the following steps: 1.

Run the BSC MML command LST OMUAREA to check the workspace where the parameter adjustment log is stored.

2.

In the ftp\intfself_mngmt\ directory of the workspace, check the file BSCID_DEPLOY_GCELLSON, BSCID_DEPLOY_GCELLSON_time.log.zip, or BSCID_DEPLOY_GCELLSON_timeDST.log.zip. NOTE

If the parameter adjustment log is greater than 0.5 MB, it is compressed. If the daylight saving time (DST) is used, the file name of the parameter adjustment log contains a DST identifier.

The following table describes the mapping relationships between the values of switch parameters and the parameter values in the parameter adjustment log. Enumeration Value Number

Parameter Value

0

OFF

1

ON

0

NO

1

YES

The following table describes the mapping relationships between the enumeration values of the PS Paging Control and CS Paging Control parameters and the enumeration value numbers in the parameter adjustment log.

Issue 01 (2016-09-05)

Enumeration Value Number

Parameter Value

0

ALWAYSNORMALPAGING(Always normal paging)

1

FIRSTPRECISEPAGING(First precise paging)

2

ALWAYSPRECISEPAGING(Always precise paging)


33



Monitor the performance counters described in 6.1.5 Performance Monitoring to observe the performance gains delivered by this feature. ----End

6.1.4.5 Deactivation Using MML Commands Run the BSC MML command SET GCELLSON with Paging Overload Control Start Threshold set to 255.

MML Command Examples SET GCELLSON: IDTYPE=BYID, CELLID=1, PagingOvldCtrlStThld=255;

Using the CME NOTE

When configuring the Automatic Paging Overload Control feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

Step 1 Configure a single object on the CME. Set the parameter described in Table 6-4 on the CME. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center) To modify objects (such as BSCs, BTSs, TRXs, GSM cells, and GSM external cells) in on the CME to start the batch modification wizard. For instructions on how batches, click to perform a batch modification through the CME batch modification center, press F1 while running the wizard to obtain online help. ----End Table 6-4 Configuring the parameter on the CME

Issue 01 (2016-09-05)

SN

MO

NE

Parameter Name

Parameter ID


1

GCELLSO N

BSC6900/ BSC6910


PagingOvld CtrlStThld

Yes


34



6.1.5 Performance Monitoring After the Automatic Paging Overload Control feature is activated, observe the counter described in Table 6-5 to monitor the performance of the feature. Table 6-5 Counter related to the Automatic Paging Overload Control feature Counter

Description

CELL.PAGING.OVERLOAD

RL3188:OVERLOAD rate of paging

6.1.6 Parameter Optimization None

6.1.7 Troubleshooting None

6.2 GBFD-171215 Automatic TCH Congestion Control 6.2.1 When to Use Automatic TCH Congestion Control It is recommended that this feature be used for cells where the K3045:Congestion Rate on TCH (All Channels Busy) is greater than 0 and the calculation result of the following formula is greater than 60%: ((K3014 - K3034) x 2 + K3034)/(CR3007 x 2 + CR3008) Counter

Description

CELL.KPI.TCH.CONGESTION.RATE

K3045:Congestion Rate on TCH (All Channels Busy)

CELL.KPI.TCH.TRAF.ERL.TRAF

K3014:Traffic Volume on TCH

CELL.KPI.TCHH.TRAF.ERL

K3034:TCHH Traffic Volume

CELL.CH.CFG.NUM.FR

CR3007:Number of Initially Configured Channels (TCHF)

CELL.CH.CFG.NUM.HR

CR3008:Number of Initially Configured Channels (TCHH)

In addition, use this feature for cells where traffic bursts occur because of certain unplanned events, such as parades or other mass gatherings. The Automatic TCH Congestion Control feature applies only to common cells, not to concentric cells. Issue 01 (2016-09-05)


35




6.2.3 Network Planning RF Planning None

Network Topology None


6.2.4 Deployment 6.2.4.1 Requirements Table 6-6 Requirements

Issue 01 (2016-09-05)

Item

Requirement

Related features


BSC

None

BTS

None

GSM networking

None

MS

None

MSC

None

License

The license control item for this feature has been activated. For details on how to activate the license, see License Management Feature Parameter Description . For details about license items, see License Control Item Description.

Others

None


36



6.2.4.2 Data Preparation Table 6-7 Data preparation Paramete r Name

Parameter ID

NE

Setting Notes

Data Source

TCH Congestio n Control Start Threshold

TCHCongC trlStThld(B SC6900,BS C6910)

BSC6900/ BSC6910

This parameter specifies the load threshold for triggering the Automatic TCH Congestion Control feature.


If this parameter is set to a value other than 255 and the TCH load in the cell exceeds the threshold specified by this parameter, the BSC performs parameter selfadjustment to reduce the TCH congestion.

6.2.4.3 Activation Using MML Commands Run the BSC MML command SET GCELLSON with TCH Congestion Control Start Threshold set to a value other than 255.

MML Command Examples SET GCELLSON: IDTYPE=BYID, CELLID=1, TCHCongCtrlStThld=80;

Using the CME NOTE

When configuring the Automatic TCH Congestion Control feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

Step 1 Configure a single object on the CME. Set the parameter described in Table 6-8 on the CME. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center) To modify objects (such as BSCs, BTSs, TRXs, GSM cells, and GSM external cells) in on the CME to start the batch modification wizard. For instructions on how batches, click to perform a batch modification through the CME batch modification center, press F1 while running the wizard to obtain online help. ----End Issue 01 (2016-09-05)


37



Table 6-8 Configuring the parameter on the CME SN

MO

NE

Parameter Name

Parameter ID


1

GCELLSO N

BSC6900/ BSC6910

TCH Congestion Control Start Threshold

TCHCongCt rlStThld

Yes

6.2.4.4 Activation Observation When TCH congestion occurs, perform the following steps to check whether the Automatic TCH Congestion Control feature has been activated: Expected result: After this feature takes effect, congestion caused by assignments is less likely to occur than before. Step 1 Run DSP commands to query the manually configured settings and the current settings of DSON parameters. Run the BSC MML command DSP GCELLSON, select a cell, and set Query Feature Type to AUTOTCHCONGCTRL(Auto TCH Congestion Control). If you do not select a cell, the cell-level DSON parameters of all cells controlled by the BSC will be queried. Expected result: Cell-level parameters related to this feature are displayed in the command output, and the configured values and current values of the parameters are inconsistent if the adaptive parameter adjustment has taken effect. Step 2 Check the parameter adjustment log of DSON. If there are parameter adjustment records in the parameter adjustment log, the Automatic TCH Congestion Control feature has been activated. Expected result: The parameters that were adaptively adjusted by this feature are displayed in the DSON log. To query the parameter adjustment log of DSON, perform the following steps: 1.


2.



The following table describes the mapping relationships between the values of switch parameters and the parameter values in the parameter adjustment log. Issue 01 (2016-09-05)


38



Enumeration Value Number

Parameter Value

0

OFF

1

ON

0

NO

1

YES

The following table describes the mapping relationships between the values of the Intracell F-H HO Allowed parameter and the parameter values in the parameter adjustment log. Enumeration Value Number

Parameter Value

0

NO

1

YES

2

HOBASECAPANDQUAL(HOBASECAPA NDQUAL)

Monitor the performance counters described in 6.2.5 Performance Monitoring to observe the performance gains delivered by this feature. ----End

6.2.4.5 Deactivation Using MML Commands Run the BSC MML command SET GCELLSON with TCH Congestion Control Start Threshold set to 255.

MML Command Examples SET GCELLSON: IDTYPE=BYID, CELLID=1, TCHCongCtrlStThld=255;

Using the CME NOTE

When configuring the Automatic TCH Congestion Control feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

Step 1 Configure a single object on the CME. Set the parameter described in Table 6-9 on the CME. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Issue 01 (2016-09-05)


39



Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center) To modify objects (such as BSCs, BTSs, TRXs, GSM cells, and GSM external cells) in batches, click on the CME to start the batch modification wizard. For instructions on how to perform a batch modification through the CME batch modification center, press F1 while running the wizard to obtain online help. ----End Table 6-9 Configuring the parameter on the CME SN

MO

NE

Parameter Name

Parameter ID


1

GCELLSO N

BSC6900/ BSC6910

TCH Congestion Control Start Threshold

TCHCongCt rlStThld

Yes

6.2.5 Performance Monitoring After the Automatic TCH Congestion Control feature is activated, observe the counters described in Table 6-10 and Table 6-11 to monitor the performance of the feature. Table 6-10 Counters related to the Automatic TCH Congestion Control feature - 1 Counter

Calculation Formula

Congestion caused by assignments

(K3021: Failed TCH Seizures due to Busy TCH (Signaling Channel) + K3011A: Failed TCH Seizures due to Busy TCH (Traffic Channel))/(K3020: TCH Seizure Requests (Signaling Channel) + K3010A: TCH Seizure Requests (Traffic Channel))

Proportion of TCHH traffic to the total traffic

K3034: TCHH Traffic Volume/K3014: Traffic Volume on TCH

NOTE

Observe congestion caused by assignments in both the cell where this feature is enabled and its neighboring cells.

Issue 01 (2016-09-05)


40



Table 6-11 Counters related to the Automatic TCH Congestion Control feature - 2 Counter

Description

CELL.INTRACELL.HO.REQ

CH300:Internal Intra-Cell Handover Requests

CELL.INTRABSC.OUTCELL.HO.REQ

CH310:Number of Outgoing Internal Inter-Cell Handover Requests

CELL.RATE.TCH.CALL.DROP.INCLUDE. HO

ZTR304:Call Drop Rate on TCH per cell(including Handover)

6.2.6 Parameter Optimization None


6.3 GBFD-180205 Adaptive Scenario-based Parameter Adjustment 6.3.1 When to Use Adaptive Scenario-based Parameter Adjustment It is recommended that this feature be used in any of the following scenarios: l

Concentric cells are configured.

l

Traffic is heavy, half-rate TCHs are required, and onsite BTSs are not BTS 2X or 3X.

l

The paging success rate is required to increase.

l

Satellite transmission over Abis is used.


6.3.3 Planning RF Planning None

Network Planning None Issue 01 (2016-09-05)


41




6.3.4 Deployment 6.3.4.1 Requirements Table 6-12 Requirements Item

Requirement

Related Features


BSC

None

BTS

None

GSM networking

None

MS

None

MSC

None

License

The license control item for this feature has been activated. For details on how to activate the license, see License Management Feature Parameter Description. For details about license items, see License Control Item Description.

Others

None

6.3.4.2 Data Preparation Table 6-13 Data preparation

Issue 01 (2016-09-05)

Parameter Name

Parameter ID

NE

Setting Notes

Data Source

Adaptive Parameter Adjustment Switch

AutoParaA djustSw(BS C6900,BSC 6910)

BSC6900/ BSC6910

This parameter specifies whether a cell supports the adaptive parameter adjustment function. You are advised to set this parameter to IUOADJUST-1& HRADJUST-1& PGADJUST -1& ABISSATELLITEADJUST-1.



42



6.3.4.3 Activation Using MML Commands Run the BSC MML command SET GCELLSON with one or multiple of the following options selected: l

IUOADJUST(Concentric Cell Adjustment)

l

HRADJUST(Half-Rate Adjustment)

l

PGADJUST(Paging Adjustment)

l

ABISSATELLITEADJUST(Abis Satellite Transmission Adjustment)

MML Command Examples SET GCELLSON: IDTYPE=BYID, CELLID=1, AutoParaAdjustSw= IUOADJUST-1& HRADJUST-1& PGADJUST -1& ABISSATELLITEADJUST-1;

Using the CME NOTE

When configuring the Adaptive Scenario-based Parameter Adjustment feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

Step 1 Configure a single object on the CME. (CME single configuration) Set the parameter described in Table 6-14 on the CME. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center) To modify objects (such as BSCs, BTSs, TRXs, GSM cells, and GSM external cells) in on the CME to start the batch modification wizard. For instructions on how batches, click to perform a batch modification through the CME batch modification center, press F1 while running the wizard to obtain online help. ----End Table 6-14 Configuring the parameter on the CME

Issue 01 (2016-09-05)

SN

MO

NE

Parameter Name

Parameter ID


1

GCELLSO N

BSC6900/ BSC6910


AutoParaAd justSw

Yes


43



6.3.4.4 Activation Observation Perform the following steps to check whether the Adaptive Scenario-based Parameter Adjustment feature is activated: Step 1 Run DSP commands to query the manually configured settings and the current settings of DSON parameters. 1.

Run the BSC MML command DSP GCELLSON, select a cell, and set Query Feature Type to AUTOPARAADJUST(base_background_adapter). If you do not select a cell, the cell-level DSON parameters of all cells controlled by the BSC will be queried.

2.

Run the BSC MML command DSP GTRXSON with Object Type set to BYCELL(By CELL) or BYTRX(By TRX), and then specify Cell Index, Cell Name, TRX ID, or TRX Name, to query the configured and current values of TRX-level parameters for this feature.

Expected result: Cell-level and TRX-level parameters related to this feature are displayed, and the configured values and current values of the parameters are inconsistent if the original configurations were inappropriate. Step 2 Check the parameter adjustment log of DSON. If there are parameter adjustment records in the parameter adjustment log, the Adaptive Scenario-based Parameter Adjustment feature has been activated. Expected result: The parameters that were adaptively adjusted by this feature are displayed in the DSON log. To query the parameter adjustment log of DSON, perform the following steps: 1.


2.



The following table describes the mapping relationships between the values of switch parameters and the parameter values in the parameter adjustment log. Enumeration Value Number

Parameter Value

0

OFF

1

ON

0

NO

1

YES

Monitor the performance counters described in 6.3.5 Performance Monitoring to observe the performance gains delivered by this feature. ----End Issue 01 (2016-09-05)


44



6.3.4.5 Deactivation Using MML Commands Run the BSC MML command SET GCELLSON with all of the following options deselected: l

IUOADJUST(Concentric Cell Adjustment)

l

HRADJUST(Half-Rate Adjustment)

l

PGADJUST(Paging Adjustment)

l

ABISSATELLITEADJUST(Abis Satellite Transmission Adjustment)

MML Command Examples SET GCELLSON: IDTYPE=BYID, CELLID=1, AutoParaAdjustSw= IUOADJUST-0& HRADJUST-0& PGADJUST -0& ABISSATELLITEADJUST-0;

Using the CME NOTE

When configuring the Adaptive Scenario-based Parameter Adjustment feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

Step 1 Configure a single object on the CME. (CME single configuration) Set the parameter described in Table 6-15 on the CME. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center) To modify objects (such as BSCs, BTSs, TRXs, GSM cells, and GSM external cells) in on the CME to start the batch modification wizard. For the method of batches, click performing batch modifications through the CME batch modification center, press F1 on the wizard interface to obtain online help. ----End Table 6-15 Configuring the parameter on the CME

Issue 01 (2016-09-05)

SN

MO

NE

Parameter Name

Parameter ID


1

GCELLSO N

BSC6900/ BSC6910


AutoParaAd justSw

Yes


45



6.3.5 Performance Monitoring After the Adaptive Scenario-based Parameter Adjustment feature is activated, observe the counters described in Table 6-16 to monitor the performance of the feature. Table 6-16 Counters related to the Adaptive Scenario-based Parameter Adjustment feature Counter

Description

CELL.CALL.ESTB.SUCC.RATE

RA333:Success Rate of Call Establishment

CELL.RATE.TCH.CALL.DROP.INCLUDE.HO

ZTR304:Call Drop Rate on TCH per cell(including Handover)

CELL.KPI.TCHH.TRAF.ERL

K3034:TCHH Traffic Volume

CELL.KPI.TCH.CONGESTION.RATE

K3045:Congestion Rate on TCH (All Channels Busy)

CELL.ASS.SUCC.RATE

RCA313: Assignment Success Rate

6.3.6 Parameter Optimization After this feature is enabled, if some counters deteriorate, disable the adaptive parameter adjustment functions related to the counters.


Issue 01 (2016-09-05)


46


7 Parameters

7

Parameters

Table 7-1 Parameters Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

Paging OvldCt rlStThl d

BSC690 0

SET GCELL SON

GBFD-1 71213

Automat ic Paging Overloa d Control

Meaning: Load threshold for triggering the Automatic Paging Overload Control feature. If this parameter is set to 255, this feature does not take effect. If this parameter is set to a value other than 255 and the PCH load in the cell reaches or exceeds the threshold specified by this parameter, the BSC performs parameter self-adjustment to reduce the PCH load. GUI Value Range: 60~100;255 Unit: None Actual Value Range: 60~100, 255 Default Value: 255

Paging OvldCt rlStThl d

BSC691 0

SET GCELL SON

GBFD-1 71213

Automat ic Paging Overloa d Control

Meaning: Load threshold for triggering the Automatic Paging Overload Control feature. If this parameter is set to 255, this feature does not take effect. If this parameter is set to a value other than 255 and the PCH load in the cell reaches or exceeds the threshold specified by this parameter, the BSC performs parameter self-adjustment to reduce the PCH load. GUI Value Range: 60~100;255 Unit: None Actual Value Range: 60~100, 255 Default Value: 255

Issue 01 (2016-09-05)


47


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

BSCLa yeredPa gingSW

BSC690 0

SET BSCEX SOFTP ARA

GBFD-1 60204

CS Layerd Paging

Meaning: Whether to enable the CS layered paging function for the BSC. ON: enable; OFF: disable. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

BSCLa yeredPa gingSW

BSC691 0

SET BSCEX SOFTP ARA

GBFD-1 60204

CS Layerd Paging

Meaning: Whether to enable the CS layered paging function for the BSC. ON: enable; OFF: disable. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

Issue 01 (2016-09-05)


48


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

PSPagi ngCtrl

BSC690 0

SET GCELL GPRS

GBFD-5 11502

Layered Paging

Meaning: Policy of transmitting PS paging messages to a cell. When the parameter is set to ALWAYSNORMALPAGING, the BSC sends PS paging messages to the paging areas specified by the CN. When the parameter is set to FIRSTPRECISEPAGING, PS paging messages in the first paging for an active PS user are sent only to the last cell on which the user camps and to its configured neighboring cells. If the first paging fails, the BSC re-sends PS paging messages to the paging areas specified by the CN. When the parameter is set to ALWAYSPRECISEPAGING, PS paging messages for an active PS user are sent to the last cell on which the user camps and to its configured neighboring cells. GUI Value Range: ALWAYSNORMALPAGING(Always normal paging), FIRSTPRECISEPAGING(First precise paging), ALWAYSPRECISEPAGING(Always precise paging) Unit: None Actual Value Range: ALWAYSNORMALPAGING, FIRSTPRECISEPAGING, ALWAYSPRECISEPAGING Default Value: ALWAYSNORMALPAGING(Always normal paging)

Issue 01 (2016-09-05)


49


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

PSPagi ngCtrl

BSC691 0

SET GCELL GPRS

GBFD-5 11502

Layered Paging

Meaning: Policy of transmitting PS paging messages to a cell. When the parameter is set to ALWAYSNORMALPAGING, the BSC sends PS paging messages to the paging areas specified by the CN. When the parameter is set to FIRSTPRECISEPAGING, PS paging messages in the first paging for an active PS user are sent only to the last cell on which the user camps and to its configured neighboring cells. If the first paging fails, the BSC re-sends PS paging messages to the paging areas specified by the CN. When the parameter is set to ALWAYSPRECISEPAGING, PS paging messages for an active PS user are sent to the last cell on which the user camps and to its configured neighboring cells. GUI Value Range: ALWAYSNORMALPAGING(Always normal paging), FIRSTPRECISEPAGING(First precise paging), ALWAYSPRECISEPAGING(Always precise paging) Unit: None Actual Value Range: ALWAYSNORMALPAGING, FIRSTPRECISEPAGING, ALWAYSPRECISEPAGING Default Value: ALWAYSNORMALPAGING(Always normal paging)

Issue 01 (2016-09-05)


50


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CSPagi ngCtrl

BSC690 0

SET GCELL SOFT

GBFD-1 60204

CS Layerd Paging

Meaning: CS paging delivery policy. ALWAYSNORMALPAGING: For all CS paging, the BSC sends paging messages according to the paging range required by the MSC. FIRSTPRECISEPAGING: For the first CS paging, the BSC sends paging messages only to the last cell on which an MS camps and to its configured neighboring cells. For subsequent CS paging, the BSC sends paging messages according to the paging range required by the MSC. ALWAYSPRECISEPAGING: For all CS paging, the BSC sends paging messages only to the last cell on which an MS camps and to its configured neighboring cells. GUI Value Range: ALWAYSNORMALPAGING(Always Normal Paging), FIRSTPRECISEPAGING(First Precise Paging), ALWAYSPRECISEPAGING(Always Precise Paging) Unit: None Actual Value Range: ALWAYSNORMALPAGING, FIRSTPRECISEPAGING, ALWAYSPRECISEPAGING Default Value: ALWAYSNORMALPAGING(Always Normal Paging)

Issue 01 (2016-09-05)


51


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CSPagi ngCtrl

BSC691 0

SET GCELL SOFT

GBFD-1 60204

CS Layerd Paging

Meaning: CS paging delivery policy. ALWAYSNORMALPAGING: For all CS paging, the BSC sends paging messages according to the paging range required by the MSC. FIRSTPRECISEPAGING: For the first CS paging, the BSC sends paging messages only to the last cell on which an MS camps and to its configured neighboring cells. For subsequent CS paging, the BSC sends paging messages according to the paging range required by the MSC. ALWAYSPRECISEPAGING: For all CS paging, the BSC sends paging messages only to the last cell on which an MS camps and to its configured neighboring cells. GUI Value Range: ALWAYSNORMALPAGING(Always Normal Paging), FIRSTPRECISEPAGING(First Precise Paging), ALWAYSPRECISEPAGING(Always Precise Paging) Unit: None Actual Value Range: ALWAYSNORMALPAGING, FIRSTPRECISEPAGING, ALWAYSPRECISEPAGING Default Value: ALWAYSNORMALPAGING(Always Normal Paging)

IMMOc cupyPC HOptS w

BSC690 0

SET GCELL OTHPA RA

GBFD-1 11705

GSM Flow Control

Meaning: Whether to enable the optimization of PCH preemption by immediate assignment messages. When this parameter is set to ON, immediate assignment messages can preempt PCHs allocated for paging messages only after the cache time of the immediate assignment messages is longer than or equal to the specified protection delay. When this parameter is set to OFF, immediate assignment messages can preempt PCHs allocated for paging messages if required. The eGBTS does not support this parameter. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

Issue 01 (2016-09-05)


52


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

IMMOc cupyPC HOptS w

BSC691 0

SET GCELL OTHPA RA

GBFD-1 11705

GSM Flow Control

Meaning: Whether to enable the optimization of PCH preemption by immediate assignment messages. When this parameter is set to ON, immediate assignment messages can preempt PCHs allocated for paging messages only after the cache time of the immediate assignment messages is longer than or equal to the specified protection delay. When this parameter is set to OFF, immediate assignment messages can preempt PCHs allocated for paging messages if required. The eGBTS does not support this parameter. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

TBFAS SADJS W

BSC690 0

SET GCELL BTSSO FTPAR A

None

None

Meaning: Priority of issuing uplink PS immediate assignment messages and CS paging messages. If this parameter is set to ON, the BTS issues uplink PS immediate assignment messages and CS paging messages, taking into account the factors such as the numbers of these two types of messages in the buffer. If this parameter is set to OFF, the BTS preferentially issues uplink PS immediate assignment messages. In this case, CS services are affected if the PS traffic is heavy. GUI Value Range: OFF(OFF), ON(ON) Unit: None Actual Value Range: OFF, ON Default Value: OFF(OFF)

Issue 01 (2016-09-05)


53


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TBFAS SADJS W

BSC691 0

SET GCELL BTSSO FTPAR A

None

None

Meaning: Priority of issuing uplink PS immediate assignment messages and CS paging messages. If this parameter is set to ON, the BTS issues uplink PS immediate assignment messages and CS paging messages, taking into account the factors such as the numbers of these two types of messages in the buffer. If this parameter is set to OFF, the BTS preferentially issues uplink PS immediate assignment messages. In this case, CS services are affected if the PS traffic is heavy. GUI Value Range: OFF(OFF), ON(ON) Unit: None Actual Value Range: OFF, ON Default Value: OFF(OFF)

Issue 01 (2016-09-05)


54


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

DynCC CHSwit ch

BSC690 0

SET GCELL CCCH

GBFD-5 11503

Dynami c Multiple CCCH

Meaning: Whether to allow dynamic conversion between TCHs and extended common control channels (CCCHs) in a cell. For details, see 3GPP TS 45.002. When this parameter is set to ON, if the load on the CCCHs increases, the TCHs corresponding to timeslots 2, 4, and 6 on the BCCH TRX are dynamically converted to CCCHs in succession. This increases the paging capability over the Um interface; if the load on the CCCHs decreases, the CCCHs corresponding to timeslots 6, 4, and 2 are dynamically converted to TCHs in succession. This increases the resource usage efficiency. If the TCH to be converted is carrying a call, the BSC forcibly hands over the call. If the forced handover fails, the BSC retains the call when either of the following conditions is met: 1. The call is an emergency call and the "EMCPRILV" parameter in the "SET GCELLCCAD" command is set to a value other than 15. 2. The call is performed by a VIP user configured in the "ADD VIPUSR" command. When neither of the conditions is met, the BSC initiates the call release procedure and the call drop occurs. Multiple CCCHs refer to logical CCCHs on multiple timeslots. Extended CCCHs refer to the CCCHs except the CCCHs on timeslot 0 on the BCCH TRX. For Huawei BSS devices, the channel type for extended CCCHs is BCH, which is the same as the channel type of multiple static CCCHs. GUI Value Range: OFF(OFF), ON(ON) Unit: None Actual Value Range: OFF, ON Default Value: OFF(OFF)

Issue 01 (2016-09-05)


55


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

DynCC CHSwit ch

BSC691 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Whether to allow dynamic conversion between TCHs and extended common control channels (CCCHs) in a cell. For details, see 3GPP TS 45.002. When this parameter is set to ON, if the load on the CCCHs increases, the TCHs corresponding to timeslots 2, 4, and 6 on the BCCH TRX are dynamically converted to CCCHs in succession. This increases the paging capability over the Um interface; if the load on the CCCHs decreases, the CCCHs corresponding to timeslots 6, 4, and 2 are dynamically converted to TCHs in succession. This increases the resource usage efficiency. If the TCH to be converted is carrying a call, the BSC forcibly hands over the call. If the forced handover fails, the BSC retains the call when either of the following conditions is met: 1. The call is an emergency call and the "EMCPRILV" parameter in the "SET GCELLCCAD" command is set to a value other than 15. 2. The call is performed by a VIP user configured in the "ADD VIPUSR" command. When neither of the conditions is met, the BSC initiates the call release procedure and the call drop occurs. Multiple CCCHs refer to logical CCCHs on multiple timeslots. Extended CCCHs refer to the CCCHs except the CCCHs on timeslot 0 on the BCCH TRX. For Huawei BSS devices, the channel type for extended CCCHs is BCH, which is the same as the channel type of multiple static CCCHs. GUI Value Range: OFF(OFF), ON(ON) Unit: None Actual Value Range: OFF, ON Default Value: OFF(OFF)

DynCC CHLoa dIncrT hr

BSC690 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Load threshold for dynamically converting a TCH to an extended CCCH. If the CCCH load is higher than the value of this parameter within the duration specified by "DynCCCHLoadDuration", a TCH is dynamically converted to an extended CCCH. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 90

Issue 01 (2016-09-05)


56


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

DynCC CHLoa dIncrT hr

BSC691 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Load threshold for dynamically converting a TCH to an extended CCCH. If the CCCH load is higher than the value of this parameter within the duration specified by "DynCCCHLoadDuration", a TCH is dynamically converted to an extended CCCH. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 90

DynCC CHLoa dRedcT hr

BSC690 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Load threshold for dynamically converting an extended CCCH to a TCH. An extended CCCH can be dynamically converted to a TCH if the following conditions are met:The CCCH load is lower than the value of this parameter within the duration specified by "DynCCCHLoadDuration".The BSC predicts that the message sending capability on the Um interface is adequate after the number of CCCHs decreases.The interval between two consecutive conversions reaches the value specified by "DynCCCHReduceInterval". GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 65

DynCC CHLoa dRedcT hr

BSC691 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Load threshold for dynamically converting an extended CCCH to a TCH. An extended CCCH can be dynamically converted to a TCH if the following conditions are met:The CCCH load is lower than the value of this parameter within the duration specified by "DynCCCHLoadDuration".The BSC predicts that the message sending capability on the Um interface is adequate after the number of CCCHs decreases.The interval between two consecutive conversions reaches the value specified by "DynCCCHReduceInterval". GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 65

Issue 01 (2016-09-05)


57


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

DynCC CHLoa dDurati on

BSC690 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Duration during which the CCCH load is higher than the value of "DynCCCHLoadIncrThr" or lower than the value of "DynCCCHLoadRedcThr". After this duration is exceeded, the BTS triggers dynamic additions or removals of extended CCCHs. GUI Value Range: 0~255 Unit: s Actual Value Range: 0~255 Default Value: 10

DynCC CHLoa dDurati on

BSC691 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Duration during which the CCCH load is higher than the value of "DynCCCHLoadIncrThr" or lower than the value of "DynCCCHLoadRedcThr". After this duration is exceeded, the BTS triggers dynamic additions or removals of extended CCCHs. GUI Value Range: 0~255 Unit: s Actual Value Range: 0~255 Default Value: 10

MaxDy nCCCH Num

BSC690 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Maximum number of extended CCCHs that can be dynamically converted in a cell. In each cell, there are a maximum of three extended CCCHs, including dynamically converted CCCHs and statically configured CCCHs. These CCCHs are carried by timeslots 2, 4, and 6 on the BCCH TRX. When the CCCH load is low, the channels on these timeslots can be occupied by signaling, CS services, or PS services. When the CCCH load is high, the channels on these timeslots are dynamically converted to extended CCCHs, which reduces the CCCH load. GUI Value Range: 1~3 Unit: None Actual Value Range: 1~3 Default Value: 2

Issue 01 (2016-09-05)


58


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

MaxDy nCCCH Num

BSC691 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Maximum number of extended CCCHs that can be dynamically converted in a cell. In each cell, there are a maximum of three extended CCCHs, including dynamically converted CCCHs and statically configured CCCHs. These CCCHs are carried by timeslots 2, 4, and 6 on the BCCH TRX. When the CCCH load is low, the channels on these timeslots can be occupied by signaling, CS services, or PS services. When the CCCH load is high, the channels on these timeslots are dynamically converted to extended CCCHs, which reduces the CCCH load. GUI Value Range: 1~3 Unit: None Actual Value Range: 1~3 Default Value: 2

DynCC CHRed uceInte rval

BSC690 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Period during which dynamic conversion from extended CCCHs to TCHs is prohibited after dynamic conversion between extended CCCHs and TCHs are performed. Specifying such period prevents ping-pong dynamic conversions due to CCCH load changes. GUI Value Range: 0~1440 Unit: min Actual Value Range: 0~1440 Default Value: 30

DynCC CHRed uceInte rval

BSC691 0

SET GCELL CCCH

GBFD-5 11503


Meaning: Period during which dynamic conversion from extended CCCHs to TCHs is prohibited after dynamic conversion between extended CCCHs and TCHs are performed. Specifying such period prevents ping-pong dynamic conversions due to CCCH load changes. GUI Value Range: 0~1440 Unit: min Actual Value Range: 0~1440 Default Value: 30

Issue 01 (2016-09-05)


59


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TCHCo ngCtrlS tThld

BSC690 0

SET GCELL SON

GBFD-1 71215

Automat ic TCH Congesti on Control

Meaning: Load threshold for triggering the Automatic TCH Congestion Control feature. If this parameter is set to 255, this feature does not take effect. If this parameter is set to a value other than 255 and the TCH load in the cell exceeds the threshold specified by this parameter, the BSC performs parameter selfadjustment to relieve the TCH congestion. GUI Value Range: 60~90;255 Unit: None Actual Value Range: 60~90, 255 Default Value: 255

TCHCo ngCtrlS tThld

BSC691 0

SET GCELL SON

GBFD-1 71215

Automat ic TCH Congesti on Control

Meaning: Load threshold for triggering the Automatic TCH Congestion Control feature. If this parameter is set to 255, this feature does not take effect. If this parameter is set to a value other than 255 and the TCH load in the cell exceeds the threshold specified by this parameter, the BSC performs parameter selfadjustment to relieve the TCH congestion. GUI Value Range: 60~90;255 Unit: None Actual Value Range: 60~90, 255 Default Value: 255

ALLO WHAL FRATE USERP ERC

BSC690 0

SET GCELL CHMG BASIC

GBFD-1 11005

Enhance d Channel Assignm ent Algorith m

Meaning: Maximum ratio of the number of half rate channels to the total number of channels in a cell. When the resource allocation principle is determined by the BSC, no half rate channel can be further assigned if the ratio of the number of half rate channels to the total number of channels in the cell is greater than or equal to the value of this parameter. When the resource allocation principle is not determined by the BSC, radio resource allocation does not depend on the setting of this parameter. Total number of channels = number of half rate channels + number of full rate channels x 2 GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 100

Issue 01 (2016-09-05)


60


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

ALLO WHAL FRATE USERP ERC

BSC691 0


GBFD-1 11005


Meaning: Maximum ratio of the number of half rate channels to the total number of channels in a cell. When the resource allocation principle is determined by the BSC, no half rate channel can be further assigned if the ratio of the number of half rate channels to the total number of channels in the cell is greater than or equal to the value of this parameter. When the resource allocation principle is not determined by the BSC, radio resource allocation does not depend on the setting of this parameter. Total number of channels = number of half rate channels + number of full rate channels x 2 GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 100

ALLO WAMR HALFR ATEUS ERPER C

BSC690 0


GBFD-1 11005


Meaning: Maximum ratio of the number of AMR half rate channels to the total number of channels in a cell. When the resource allocation principle is determined by the BSC, no AMR half rate channel can be further assigned if the ratio of the number of AMR half rate channels to the total number of channels in the cell is greater than or equal to the value of this parameter. When the resource allocation principle is not determined by the BSC, radio resource allocation does not depend on the setting of this parameter. Total number of channels = number of half rate channels + number of full rate channels x 2 GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 100

Issue 01 (2016-09-05)


61


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

ALLO WAMR HALFR ATEUS ERPER C

BSC691 0


GBFD-1 11005


Meaning: Maximum ratio of the number of AMR half rate channels to the total number of channels in a cell. When the resource allocation principle is determined by the BSC, no AMR half rate channel can be further assigned if the ratio of the number of AMR half rate channels to the total number of channels in the cell is greater than or equal to the value of this parameter. When the resource allocation principle is not determined by the BSC, radio resource allocation does not depend on the setting of this parameter. Total number of channels = number of half rate channels + number of full rate channels x 2 GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 100

AMRT CHHP RIORA LLOW

BSC690 0

SET GCELL CHMG AD

GBFD-1 13402

Dynami c Adjustm ent Between FR and HR

Meaning: Whether channels are assigned and TCHF-to-TCHH handover decisions are made on the basis of the AMR TCH/H prior cell load threshold if AMR calls are detected. When this parameter is set to ON, the channel assignment algorithm uses the AMR TCH/H prior cell load threshold to determine whether to assign TCHHs to AMR calls, and Handover algorithm generation 1 uses the AMR TCH/H prior cell load threshold to determine whether to hand over AMR calls occupying TCHFs to TCHHs; When this parameter is set to OFF, the AMR TCH/H prior cell load threshold is not used during channel assignment, Handover algorithm generation 1 determines whether to hand over AMR calls occupying TCHFs to TCHHs without considering traffic in the corresponding cell. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: ON(On)

Issue 01 (2016-09-05)


62


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

AMRT CHHP RIORA LLOW

BSC691 0

SET GCELL CHMG AD

GBFD-1 13402


Meaning: Whether channels are assigned and TCHF-to-TCHH handover decisions are made on the basis of the AMR TCH/H prior cell load threshold if AMR calls are detected. When this parameter is set to ON, the channel assignment algorithm uses the AMR TCH/H prior cell load threshold to determine whether to assign TCHHs to AMR calls, and Handover algorithm generation 1 uses the AMR TCH/H prior cell load threshold to determine whether to hand over AMR calls occupying TCHFs to TCHHs; When this parameter is set to OFF, the AMR TCH/H prior cell load threshold is not used during channel assignment, Handover algorithm generation 1 determines whether to hand over AMR calls occupying TCHFs to TCHHs without considering traffic in the corresponding cell. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: ON(On)

AMRT CHHP RIORL OAD

BSC690 0

SET GCELL CHMG AD

GBFD-1 13402


Meaning: Load threshold for assigning half rate channels preferentially. If the current TCH seizure ratio of the cell is greater than or equal to this threshold, AMR half rate channels are assigned preferentially. GUI Value Range: 0~99 Unit: % Actual Value Range: 0~99 Default Value: 55

AMRT CHHP RIORL OAD

BSC691 0

SET GCELL CHMG AD

GBFD-1 13402


Meaning: Load threshold for assigning half rate channels preferentially. If the current TCH seizure ratio of the cell is greater than or equal to this threshold, AMR half rate channels are assigned preferentially. GUI Value Range: 0~99 Unit: % Actual Value Range: 0~99 Default Value: 55

Issue 01 (2016-09-05)


63


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TCHBU SYTHR ES

BSC690 0

SET GCELL CHMG AD

None

None

Meaning: If the current channel seizure ratio reaches or exceeds this value, the half-rate TCH is assigned preferentially; otherwise, the full-rate TCH is assigned preferentially. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 60

TCHBU SYTHR ES

BSC691 0

SET GCELL CHMG AD

None

None

Meaning: If the current channel seizure ratio reaches or exceeds this value, the half-rate TCH is assigned preferentially; otherwise, the full-rate TCH is assigned preferentially. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 60

INTRA CELLF HHOE N

BSC690 0

SET GCELL HOBAS IC

GBFD-1 13402


Meaning: Whether to allow AMR handovers. If this parameter is set to YES, AMR handovers are allowed. If this parameter is set to NO, AMR handovers are not allowed. Setting this parameter to YES or NO has no impact on dynamic non-AMR TCHF-TCHH handovers. If this parameter is set to HOBASECAPANDQUAL, the TCHF-TCHH handover algorithm based on capacity and quality is allowed. GUI Value Range: NO(No), YES(Yes), HOBASECAPANDQUAL(HOBASECAPANDQUA L) Unit: None Actual Value Range: NO, YES, HOBASECAPANDQUAL Default Value: NO(No)

Issue 01 (2016-09-05)


64


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

INTRA CELLF HHOE N

BSC691 0

SET GCELL HOBAS IC

GBFD-1 13402


Meaning: Whether to allow AMR handovers. If this parameter is set to YES, AMR handovers are allowed. If this parameter is set to NO, AMR handovers are not allowed. Setting this parameter to YES or NO has no impact on dynamic non-AMR TCHF-TCHH handovers. If this parameter is set to HOBASECAPANDQUAL, the TCHF-TCHH handover algorithm based on capacity and quality is allowed. GUI Value Range: NO(No), YES(Yes), HOBASECAPANDQUAL(HOBASECAPANDQUA L) Unit: None Actual Value Range: NO, YES, HOBASECAPANDQUAL Default Value: NO(No)

AMRF ULLTO HALFH OALL OW

BSC690 0

SET GCELL HOBAS IC

GBFD-1 10601

HUAW EI I Handov er

Meaning: Whether to enable the algorithm for loadand quality-based AMR TCHF-to-TCHH handovers. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

AMRF ULLTO HALFH OALL OW

BSC691 0

SET GCELL HOBAS IC

GBFD-1 10601

HUAW EI I Handov er

Meaning: Whether to enable the algorithm for loadand quality-based AMR TCHF-to-TCHH handovers. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

NOAM RFULL TOHA LFHOA LLOW

BSC690 0

Issue 01 (2016-09-05)

SET GCELL HOBAS IC

GBFD-1 10601 GBFD-5 10501

HUAW EI I Handov er HUAW EI II Handov er

Meaning: Whether to allow non-AMR voice F-H handover. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)


65


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

NOAM RFULL TOHA LFHOA LLOW

BSC691 0

SET GCELL HOBAS IC

GBFD-1 10601

HUAW EI I Handov er

Meaning: Whether to allow non-AMR voice F-H handover.

AMRH ALFTO FULLH OQUA LALLO W

GBFD-5 10501

HUAW EI II Handov er BSC690 0

SET GCELL HOBAS IC

GBFD-1 10601

HUAW EI I Handov er

GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No) Meaning: Whether to enable the algorithm for qualitybased AMR TCHH-to-TCHF handovers. Even if the cell load does not reach the threshold, TCHH-toTCHF handover decisions can be made when this parameter is set to YES(Yes). GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

AMRH ALFTO FULLH OQUA LALLO W

BSC691 0

SET GCELL HOBAS IC

GBFD-1 10601

HUAW EI I Handov er

Meaning: Whether to enable the algorithm for qualitybased AMR TCHH-to-TCHF handovers. Even if the cell load does not reach the threshold, TCHH-toTCHF handover decisions can be made when this parameter is set to YES(Yes). GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

NOAM RHALF TOFUL LHOQ UALAL LOW

BSC690 0

SET GCELL HOBAS IC

GBFD-5 10501

HUAW EI II Handov er

Meaning: Whether to trigger non-AMR H-F handovers according to the uplink and downlink receive quality. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

NOAM RHALF TOFUL LHOQ UALAL LOW

BSC691 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Whether to trigger non-AMR H-F handovers according to the uplink and downlink receive quality. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

Issue 01 (2016-09-05)


66


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

AMRF ULLTO HALFH OTHR ESH

BSC690 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Threshold for the load in a cell during AMR TCHF-to-TCHH handovers. AMR TCHF-to-TCHH handover decisions can be made when the cell load is higher than this threshold. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 75

AMRF ULLTO HALFH OTHR ESH

BSC691 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Threshold for the load in a cell during AMR TCHF-to-TCHH handovers. AMR TCHF-to-TCHH handover decisions can be made when the cell load is higher than this threshold. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 75

NOAM RFULL TOHA LFTHR ESH

BSC690 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Threshold for the load in a cell during nonAMR TCHF-to-TCHH handovers. Non-AMR TCHFto-TCHH handover decisions can be made when the cell load is higher than this threshold. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 85

NOAM RFULL TOHA LFTHR ESH

BSC691 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Threshold for the load in a cell during nonAMR TCHF-to-TCHH handovers. Non-AMR TCHFto-TCHH handover decisions can be made when the cell load is higher than this threshold. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 85

Issue 01 (2016-09-05)


67


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

INTRA CELLH OEN

BSC690 0

SET GCELL HOBAS IC

GBFD-1 10601

HUAW EI I Handov er

Meaning: Whether to allow intra-cell handovers. Forced intra-cell handovers or AMR TCHF-to-TCHH handovers in the case of Huawei handover algorithm I are not subject to this parameter.


GUI Value Range: NO(No), YES(Yes)

GBFD-5 10501

Unit: None Actual Value Range: NO, YES Default Value: NO(No)

INTRA CELLH OEN

BSC691 0

SET GCELL HOBAS IC

GBFD-1 10601 GBFD-5 10501

HUAW EI I Handov er

Meaning: Whether to allow intra-cell handovers. Forced intra-cell handovers or AMR TCHF-to-TCHH handovers in the case of Huawei handover algorithm I are not subject to this parameter.


GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

LoadHo En

BSC690 0

SET GCELL HOBAS IC

GBFD-1 10601 GBFD-5 10501


Meaning: This parameter specifies whether a traffic load-sharing handover is enabled. The load handover helps to reduce cell congestion, improve success rate of channel assignment, and balance the traffic load among cells, thus improving the network performance. The load handover is used as an emergency measure instead of a primary measure to adjust abnormal traffic burst in partial areas. If load handovers occur frequently in a partial area, the cell and TRX configuration of BTSs and the network layout should be adjusted. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

Issue 01 (2016-09-05)


68


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

LoadHo En

BSC691 0

SET GCELL HOBAS IC

GBFD-1 10601

HUAW EI I Handov er

Meaning: This parameter specifies whether a traffic load-sharing handover is enabled. The load handover helps to reduce cell congestion, improve success rate of channel assignment, and balance the traffic load among cells, thus improving the network performance. The load handover is used as an emergency measure instead of a primary measure to adjust abnormal traffic burst in partial areas. If load handovers occur frequently in a partial area, the cell and TRX configuration of BTSs and the network layout should be adjusted.

GBFD-5 10501


GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No) TRIGT HRES

BSC690 0

SET GCELL HOAD

GBFD-1 14322 GBFD-1 10601 GBFD-5 10501

TRIGT HRES

BSC691 0

SET GCELL HOAD

GBFD-1 14322 GBFD-1 10601 GBFD-5 10501

Issue 01 (2016-09-05)

GSM/ WCDM A Load Based Handov er

Meaning: A load-based handover is started when the cell load is greater than or equal to this threshold. For inter-BSC load-based handovers, when "LOADHOHYSTADAPEN" is set to YES, this parameter is only used for decision on load-based handovers at the same layer.

HUAW EI I Handov er

GUI Value Range: 0~100


Default Value: 90

GSM/ WCDM A Load Based Handov er

Meaning: A load-based handover is started when the cell load is greater than or equal to this threshold. For inter-BSC load-based handovers, when "LOADHOHYSTADAPEN" is set to YES, this parameter is only used for decision on load-based handovers at the same layer.

HUAW EI I Handov er

GUI Value Range: 0~100


Default Value: 90

Unit: % Actual Value Range: 0~100

Unit: % Actual Value Range: 0~100


69


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

LoadAc cThres

BSC690 0

SET GCELL HOAD

GBFD-1 10601

HUAW EI I Handov er

Meaning:

GBFD-5 10501


Threshold for allowing MSs to hand over from other cells to the cell through load-based handovers. MSs are allowed to hand over from other cells to the cell through load-based handovers if any of the following conditions is met: 1. The cell load is lower than or equal to this threshold when "HOCTRLSWITCH" is set to HOALGORITHM1 and "LOADHOAD" is set to YES in the "SET GCELLHOBASIC" command. 2. The cell load is lower than this threshold in other cases. If neither of the preceding conditions is met, MSs are not allowed to hand over from other cells to the cell through load-based handovers. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 80

LoadAc cThres

BSC691 0

SET GCELL HOAD

GBFD-1 10601 GBFD-5 10501


Meaning: Threshold for allowing MSs to hand over from other cells to the cell through load-based handovers. MSs are allowed to hand over from other cells to the cell through load-based handovers if any of the following conditions is met: 1. The cell load is lower than or equal to this threshold when "HOCTRLSWITCH" is set to HOALGORITHM1 and "LOADHOAD" is set to YES in the "SET GCELLHOBASIC" command. 2. The cell load is lower than this threshold in other cases. If neither of the preceding conditions is met, MSs are not allowed to hand over from other cells to the cell through load-based handovers. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 80

Issue 01 (2016-09-05)


70


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

LOAD HOPER IOD

BSC690 0

SET GCELL HOAD

GBFD-1 10601

HUAW EI I Handov er

Meaning:

GBFD-5 10501


If the cell load reaches or exceeds "Load HO Threshold", all calls in the serving cell initiate handover requests at the same time, which will suddenly increase the load of the CPU. When the traffic volume is high, congestion occurs in the cell, leading to call drops. To resolve this problem, the BSC uses the hierarchical load handover algorithm to control the number of MSs included in each level of handovers. This parameter indicates the duration of each handover level. GUI Value Range: 1~255 Unit: s Actual Value Range: 1~255 Default Value: 10

LOAD HOPER IOD

BSC691 0

SET GCELL HOAD

GBFD-1 10601 GBFD-5 10501


Meaning: If the cell load reaches or exceeds "Load HO Threshold", all calls in the serving cell initiate handover requests at the same time, which will suddenly increase the load of the CPU. When the traffic volume is high, congestion occurs in the cell, leading to call drops. To resolve this problem, the BSC uses the hierarchical load handover algorithm to control the number of MSs included in each level of handovers. This parameter indicates the duration of each handover level. GUI Value Range: 1~255 Unit: s Actual Value Range: 1~255 Default Value: 10

Issue 01 (2016-09-05)


71


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

LOAD HOSTE P

BSC690 0

SET GCELL HOAD

GBFD-1 10601

HUAW EI I Handov er

Meaning:

GBFD-5 10501


In hierarchical load handover algorithm I, starting from "DLEDGETHRES", a "LOADHOSTEP" is added to the upper handover threshold after every "LOADHOPERIOD". In this way, all the calls in the current serving cell whose receive level ranging from "DLEDGETHRES" to "DLEDGETHRES" + "LOADOFFSET" are handed over to other cells. In hierarchical load handover algorithm II, starting from ("INTERCELLHYST" - 64), a "LOADHOSTEP" is removed from the lower handover threshold after every "LOADHOPERIOD". In this way, all the calls whose receive levels in the neighboring cell and current serving cell have a difference ranging from ("INTERCELLHYST" - 64 "LOADOFFSET") to ("INTERCELLHYST" - 64) are handed over to other cells. GUI Value Range: 1~63 Unit: dB Actual Value Range: 1~63 Default Value: 5

LOAD HOSTE P

BSC691 0

SET GCELL HOAD

GBFD-1 10601 GBFD-5 10501


Meaning: In hierarchical load handover algorithm I, starting from "DLEDGETHRES", a "LOADHOSTEP" is added to the upper handover threshold after every "LOADHOPERIOD". In this way, all the calls in the current serving cell whose receive level ranging from "DLEDGETHRES" to "DLEDGETHRES" + "LOADOFFSET" are handed over to other cells. In hierarchical load handover algorithm II, starting from ("INTERCELLHYST" - 64), a "LOADHOSTEP" is removed from the lower handover threshold after every "LOADHOPERIOD". In this way, all the calls whose receive levels in the neighboring cell and current serving cell have a difference ranging from ("INTERCELLHYST" - 64 "LOADOFFSET") to ("INTERCELLHYST" - 64) are handed over to other cells. GUI Value Range: 1~63 Unit: dB Actual Value Range: 1~63 Default Value: 5

Issue 01 (2016-09-05)


72


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

LOAD OFFSE T

BSC690 0

SET GCELL HOAD

GBFD-1 10601

HUAW EI I Handov er

Meaning:

GBFD-5 10501


In handover algorithm I, load handovers can be performed only when the receive level of the current serving cell is in the range "Edge HO DL RX_LEV Threshold" to "Edge HO DL RX_LEV Threshold" + "Load HO Bandwidth". In handover algorithm II, load handovers can be performed only when the level difference between the neighboring cell and the serving cell is between ("Inter-cell HO Hysteresis" - 64) - "Load HO Bandwidth" and ("Inter-cell HO Hysteresis" - 64). GUI Value Range: 0~63 Unit: dB Actual Value Range: 0~63 Default Value: 25

LOAD OFFSE T

BSC691 0

SET GCELL HOAD

GBFD-1 10601 GBFD-5 10501


Meaning: In handover algorithm I, load handovers can be performed only when the receive level of the current serving cell is in the range "Edge HO DL RX_LEV Threshold" to "Edge HO DL RX_LEV Threshold" + "Load HO Bandwidth". In handover algorithm II, load handovers can be performed only when the level difference between the neighboring cell and the serving cell is between ("Inter-cell HO Hysteresis" - 64) - "Load HO Bandwidth" and ("Inter-cell HO Hysteresis" - 64). GUI Value Range: 0~63 Unit: dB Actual Value Range: 0~63 Default Value: 25

AMRF ULLTO HALFH OQUA LTHRE SH

BSC690 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Quality threshold for the AMR handover from full rate to half rate. If the uplink and downlink receive quality levels of an AMR full rate call are both equal to or less than "AMRFULLTOHALFHOQUALTHRESH" + "AMRF2HHOQUALTHFINE"*0.1, the AMR call is handed over from full rate to half rate. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 Default Value: 0

Issue 01 (2016-09-05)


73


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

AMRF ULLTO HALFH OQUA LTHRE SH

BSC691 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Quality threshold for the AMR handover from full rate to half rate. If the uplink and downlink receive quality levels of an AMR full rate call are both equal to or less than "AMRFULLTOHALFHOQUALTHRESH" + "AMRF2HHOQUALTHFINE"*0.1, the AMR call is handed over from full rate to half rate. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 Default Value: 0

NOAM RFULL TOHA LFHO QUALT HRESH

BSC690 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Quality threshold for non-AMR F-H handovers. When the uplink receive quality and downlink receive quality of a user are both equal to or less than "NOAMRFULLTOHALFHOQUALTHRESH" + "NOAMRF2HHOQUALTHFINE"*0.1, a F-H handover can be triggered for the user. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 Default Value: 0

NOAM RFULL TOHA LFHO QUALT HRESH

BSC691 0

SET GCELL HOBAS IC

GBFD-5 10501


Meaning: Quality threshold for non-AMR F-H handovers. When the uplink receive quality and downlink receive quality of a user are both equal to or less than "NOAMRFULLTOHALFHOQUALTHRESH" + "NOAMRF2HHOQUALTHFINE"*0.1, a F-H handover can be triggered for the user. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 Default Value: 0

Issue 01 (2016-09-05)


74


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

DIREC TRYEN

BSC690 0

SET GCELL BASIC PARA

GBFD-1 10607

Direct Retry

Meaning: Whether to enable a directed retry. The directed retry is to hand over an MS to a neighboring cell in the same procedure as the handover. The directed retry is an emergency measure applicable to abnormal traffic peaks in some areas of a radio network. You should not use the directed retry as a major means of solving traffic congestion. If the directed retry always occurs in some areas of a network, consider adjusting the sector and TRX configuration and the network layout. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: YES(Yes)

DIREC TRYEN

BSC691 0

SET GCELL BASIC PARA

GBFD-1 10607

Direct Retry

Meaning: Whether to enable a directed retry. The directed retry is to hand over an MS to a neighboring cell in the same procedure as the handover. The directed retry is an emergency measure applicable to abnormal traffic peaks in some areas of a radio network. You should not use the directed retry as a major means of solving traffic congestion. If the directed retry always occurs in some areas of a network, consider adjusting the sector and TRX configuration and the network layout. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: YES(Yes)

Issue 01 (2016-09-05)


75


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

ASSLO ADJUD GEEN

BSC690 0

SET GCELL CCBAS IC

GBFD-1 10607

Direct Retry

Meaning: Whether to enable the directed retry based on cell load. Directed retry is enabled if the following conditions are met: This parameter is set to ENABLE. The cell supports directed retry. The current cell load is larger than or equal to the value of "CDRTTRYFBDTHRES" in "SET GCELLOTHEXT" during assignment. If this parameter is set to DISABLE, the MS attempts to apply for a channel in the serving cell. If the application fails, it continues with the directed retry procedure. GUI Value Range: DISABLE(Disable), ENABLE(Enable) Unit: None Actual Value Range: DISABLE, ENABLE Default Value: DISABLE(Disable)

ASSLO ADJUD GEEN

BSC691 0

SET GCELL CCBAS IC

GBFD-1 10607

Direct Retry

Meaning: Whether to enable the directed retry based on cell load. Directed retry is enabled if the following conditions are met: This parameter is set to ENABLE. The cell supports directed retry. The current cell load is larger than or equal to the value of "CDRTTRYFBDTHRES" in "SET GCELLOTHEXT" during assignment. If this parameter is set to DISABLE, the MS attempts to apply for a channel in the serving cell. If the application fails, it continues with the directed retry procedure. GUI Value Range: DISABLE(Disable), ENABLE(Enable) Unit: None Actual Value Range: DISABLE, ENABLE Default Value: DISABLE(Disable)

Issue 01 (2016-09-05)


76


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CDRTT RYFBD THRES

BSC690 0

SET GCELL OTHE XT

GBFD-1 10607

Direct Retry

Meaning: Threshold for forbidding directed retry based on cell load. Channels are allocated to MSs by performing the directed retry procedure during assignment if the following conditions are met: "ASSLOADJUDGEEN" in "SET GCELLCCBASIC" is set to ENABLE. The cell supports directed retry. The current cell load is larger than or equal to the value of this parameter. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 90

CDRTT RYFBD THRES

BSC691 0

SET GCELL OTHE XT

GBFD-1 10607

Direct Retry

Meaning: Threshold for forbidding directed retry based on cell load. Channels are allocated to MSs by performing the directed retry procedure during assignment if the following conditions are met: "ASSLOADJUDGEEN" in "SET GCELLCCBASIC" is set to ENABLE. The cell supports directed retry. The current cell load is larger than or equal to the value of this parameter. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 90

Issue 01 (2016-09-05)


77


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

AutoPa raAdjus tSw

BSC690 0

SET GCELL SON

GBFD-1 80205

Adaptiv e Scenario -based Paramet er Adjustm ent

Meaning: Controls whether a cell supports the adaptive parameter adjustment function in the following scenarios. If an option under this parameter is selected, the adaptive parameter adjustment function in the corresponding scenario is enabled; if an option under this parameter is deselected, the function is disabled. If IUOADJUST is selected under this parameter, the switch is turned on. In the concentric cell scenario, the BSC adaptively adjusts the value of "FMSMAXOPCC" in the "SET GCELLCCCH" command based on the BCCH frequency band type to ensure that the value of "FMSMAXOPCC" is consistent with the maximum MS transmit power level at the BCCH frequency band in the cell. If IUOADJUST is deselected, the BSC does not adaptively adjust the value of "FMSMAXOPCC" in the "SET GCELLCCCH" command in this scenario. If HRADJUST is selected under this parameter, the switch is turned on. In the half-rate speech version scenario, the BSC adaptively adjusts the value of "TCHAJFLAG" in the "SET GTRXDEV" command for all the TRXs in the cell to ensure that all these TRXs support the TCHF-to-TCHH conversion. If HRADJUST is deselected, the BSC does not adaptively adjust the value of "TCHAJFLAG" in the "SET GTRXDEV" command in this scenario. If PGADJUST is selected under this parameter, the switch is turned on. The BSC adaptively adjusts the values of "BSPAMFRAMS" in the "SET GCELLIDLEBASIC" command and "BSSPAGINGCOORDINATION" in the "SET GCELLPSBASE" command to increase the paging success rate. If PGADJUST is deselected, the BSC does not adaptively adjust the values of these parameters. If ABISSATELLITEADJUST is selected under this parameter, the switch is turned on. The BSC adaptively adjusts the value of "TX" in the "SET GCELLIDLEBASIC" command when the Abis interface uses satellite transmission to ensure that the optimal setting is used. If ABISSATELLITEADJUST is deselected, the BSC does not adaptively adjust the value of "TX" in the "SET GCELLIDLEBASIC" command in this scenario.

Issue 01 (2016-09-05)


78


Parame ter ID

NE

MML Comma nd

7 Parameters

Feature ID

Feature Name

Description

GUI Value Range: IUOADJUST(Concentric Cell Adjustment), HRADJUST(Half-Rate Adjustment), PGADJUST(Paging Adjustment), ABISSATELLITEADJUST(Abis Satellite Transmission Adjustment) Unit: None Actual Value Range: IUOADJUST, HRADJUST, PGADJUST, ABISSATELLITEADJUST Default Value: IUOADJUST:0, HRADJUST:0, PGADJUST:0, ABISSATELLITEADJUST:0

Issue 01 (2016-09-05)


79


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

AutoPa raAdjus tSw

BSC691 0

SET GCELL SON

GBFD-1 80205

Adaptiv e Scenario -based Paramet er Adjustm ent

Meaning: Controls whether a cell supports the adaptive parameter adjustment function in the following scenarios. If an option under this parameter is selected, the adaptive parameter adjustment function in the corresponding scenario is enabled; if an option under this parameter is deselected, the function is disabled. If IUOADJUST is selected under this parameter, the switch is turned on. In the concentric cell scenario, the BSC adaptively adjusts the value of "FMSMAXOPCC" in the "SET GCELLCCCH" command based on the BCCH frequency band type to ensure that the value of "FMSMAXOPCC" is consistent with the maximum MS transmit power level at the BCCH frequency band in the cell. If IUOADJUST is deselected, the BSC does not adaptively adjust the value of "FMSMAXOPCC" in the "SET GCELLCCCH" command in this scenario. If HRADJUST is selected under this parameter, the switch is turned on. In the half-rate speech version scenario, the BSC adaptively adjusts the value of "TCHAJFLAG" in the "SET GTRXDEV" command for all the TRXs in the cell to ensure that all these TRXs support the TCHF-to-TCHH conversion. If HRADJUST is deselected, the BSC does not adaptively adjust the value of "TCHAJFLAG" in the "SET GTRXDEV" command in this scenario. If PGADJUST is selected under this parameter, the switch is turned on. The BSC adaptively adjusts the values of "BSPAMFRAMS" in the "SET GCELLIDLEBASIC" command and "BSSPAGINGCOORDINATION" in the "SET GCELLPSBASE" command to increase the paging success rate. If PGADJUST is deselected, the BSC does not adaptively adjust the values of these parameters. If ABISSATELLITEADJUST is selected under this parameter, the switch is turned on. The BSC adaptively adjusts the value of "TX" in the "SET GCELLIDLEBASIC" command when the Abis interface uses satellite transmission to ensure that the optimal setting is used. If ABISSATELLITEADJUST is deselected, the BSC does not adaptively adjust the value of "TX" in the "SET GCELLIDLEBASIC" command in this scenario.

Issue 01 (2016-09-05)


80


Parame ter ID

NE

MML Comma nd

7 Parameters

Feature ID

Feature Name

Description

GUI Value Range: IUOADJUST(Concentric Cell Adjustment), HRADJUST(Half-Rate Adjustment), PGADJUST(Paging Adjustment), ABISSATELLITEADJUST(Abis Satellite Transmission Adjustment) Unit: None Actual Value Range: IUOADJUST, HRADJUST, PGADJUST, ABISSATELLITEADJUST Default Value: IUOADJUST:0, HRADJUST:0, PGADJUST:0, ABISSATELLITEADJUST:0 FMSM AXOPC C

BSC690 0

SET GCELL CCCH

GBFD-1 11101 GBFD-1 11003

System Informat ion Sending Radio Commo n Channel Manage ment

Meaning: Maximum transmit power level of MSs. As one of the cell reselection parameters in system message 3, this parameter is used to control the transmit power of MSs. For details, see GSM Rec. 05.05. In a GSM900 cell, the maximum power control level of an MS ranges from 0 to 19, corresponding respectively to the following values (unit: dBm): 43, 41, 39, 37, 35, 33, 31, 29, 27, 25, 23, 21, 19, 17, 15, 13, 11, 9, 7, and 5.Generally, the maximum transmit power supported by an MS is level 5 (corresponding to 33 dBm). The minimum transmit power supported by an MS is level 19 (corresponding to 5 dBm). Other transmit power levels are reserved for high-power MSs. In a GSM1800 or GSM1900 cell, the maximum power control level of an MS ranges from 0 to 31, corresponding respectively to the following values (unit: dBm): 30, 28, 26, 24, 22, 20, 18, 16, 14, 12, 10, 8, 6, 4, 2, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 36, 34, and 32. Generally, the maximum transmit power supported by an MS is level 0 (corresponding to 30 dBm). The minimum transmit power supported by an MS is level 15 (corresponding to 0 dBm). Other transmit power levels are reserved for high-power MSs. GUI Value Range: 0~19 Unit: None Actual Value Range: 0~19 Default Value: 5

Issue 01 (2016-09-05)


81


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

FMSM AXOPC C

BSC691 0

SET GCELL CCCH

GBFD-1 11101

System Informat ion Sending

Meaning:

GBFD-1 11003

Radio Commo n Channel Manage ment

Maximum transmit power level of MSs. As one of the cell reselection parameters in system message 3, this parameter is used to control the transmit power of MSs. For details, see GSM Rec. 05.05. In a GSM900 cell, the maximum power control level of an MS ranges from 0 to 19, corresponding respectively to the following values (unit: dBm): 43, 41, 39, 37, 35, 33, 31, 29, 27, 25, 23, 21, 19, 17, 15, 13, 11, 9, 7, and 5.Generally, the maximum transmit power supported by an MS is level 5 (corresponding to 33 dBm). The minimum transmit power supported by an MS is level 19 (corresponding to 5 dBm). Other transmit power levels are reserved for high-power MSs. In a GSM1800 or GSM1900 cell, the maximum power control level of an MS ranges from 0 to 31, corresponding respectively to the following values (unit: dBm): 30, 28, 26, 24, 22, 20, 18, 16, 14, 12, 10, 8, 6, 4, 2, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 36, 34, and 32. Generally, the maximum transmit power supported by an MS is level 0 (corresponding to 30 dBm). The minimum transmit power supported by an MS is level 15 (corresponding to 0 dBm). Other transmit power levels are reserved for high-power MSs. GUI Value Range: 0~19 Unit: None Actual Value Range: 0~19 Default Value: 5

Issue 01 (2016-09-05)


82


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TCHAJ FLAG

BSC690 0

SET GTRX DEV

None

None

Meaning: Whether to allow the cell to dynamically change a channel from full rate to half rate, from half rate to full rate, or from a dynamic PDCH to a TCH half-rate channel. This parameter helps determine the dynamic channel conversion priority in the channel allocation algorithm. During channel allocation, the BSC preferentially allocates channels on a TRX that does not allow dynamic channel conversion. If this parameter is set to Yes, the conversion is allowed. If this parameter is set to No, the conversion is not allowed and the changed channel is restored to the previous rate mode. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

TCHAJ FLAG

BSC691 0

SET GTRX DEV

None

None

Meaning: Whether to allow the cell to dynamically change a channel from full rate to half rate, from half rate to full rate, or from a dynamic PDCH to a TCH half-rate channel. This parameter helps determine the dynamic channel conversion priority in the channel allocation algorithm. During channel allocation, the BSC preferentially allocates channels on a TRX that does not allow dynamic channel conversion. If this parameter is set to Yes, the conversion is allowed. If this parameter is set to No, the conversion is not allowed and the changed channel is restored to the previous rate mode. GUI Value Range: NO(No), YES(Yes) Unit: None Actual Value Range: NO, YES Default Value: NO(No)

Issue 01 (2016-09-05)


83


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

BSPAM FRAMS

BSC690 0

SET GCELL IDLEB ASIC

GBFD-1 11003


Meaning:

GBFD-1 10303

CS Paging

Number of multiframes in a cycle on a paging subchannel. In fact, this parameter specifies the number of paging sub-channels that a paging channel in a cell is divided into. In an actual network, an MS does not listen to other paging sub-channels but its belonging paging subchannel only. For details, see 3GPP TS 05.02 and 05.08. The larger the value of this parameter, the more the number of the paging sub-channels in a cell, and the fewer the number of the users belonging to each paging sub-channel. In this case, the mean uptime of the MS battery can be prolonged. For details, see the computing mode of paging group in 3GPP TS 05.02. The larger the value of this parameter, however, the larger the time delay of a paging message in a space segment. Therefore, the average service performance of the system lowers. Based on the principle of ensuring that overload does not occur on paging channels, set this parameter to a value as small as possible. You must regularly measure the overload conditions of the paging channels in a running network and accordingly adjust the value of this parameter properly. A paging message in a location area must be sent in all the cells within this location area at the same time. Therefore, the capacity of a paging channel of each cell in a location area must be the same or nearly the same. The capacity refers to the calculated number of paging sub-channels of each cell. GUI Value Range: 2_M_PERIOD(2 Multiframe Period), 3_M_PERIOD(3 Multiframe Period), 4_M_PERIOD(4 Multiframe Period), 5_M_PERIOD(5 Multiframe Period), 6_M_PERIOD(6 Multiframe Period), 7_M_PERIOD(7 Multiframe Period), 8_M_PERIOD(8 Multiframe Period), 9_M_PERIOD(9 Multiframe Period) Unit: 235ms Actual Value Range: 470, 705, 940, 1175, 1410, 1645, 1880, 2115 Default Value: 2_M_PERIOD(2 Multiframe Period)

Issue 01 (2016-09-05)


84


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

BSPAM FRAMS

BSC691 0


GBFD-1 11003


Meaning:

GBFD-1 10303

CS Paging

Number of multiframes in a cycle on a paging subchannel. In fact, this parameter specifies the number of paging sub-channels that a paging channel in a cell is divided into. In an actual network, an MS does not listen to other paging sub-channels but its belonging paging subchannel only. For details, see 3GPP TS 05.02 and 05.08. The larger the value of this parameter, the more the number of the paging sub-channels in a cell, and the fewer the number of the users belonging to each paging sub-channel. In this case, the mean uptime of the MS battery can be prolonged. For details, see the computing mode of paging group in 3GPP TS 05.02. The larger the value of this parameter, however, the larger the time delay of a paging message in a space segment. Therefore, the average service performance of the system lowers. Based on the principle of ensuring that overload does not occur on paging channels, set this parameter to a value as small as possible. You must regularly measure the overload conditions of the paging channels in a running network and accordingly adjust the value of this parameter properly. A paging message in a location area must be sent in all the cells within this location area at the same time. Therefore, the capacity of a paging channel of each cell in a location area must be the same or nearly the same. The capacity refers to the calculated number of paging sub-channels of each cell. GUI Value Range: 2_M_PERIOD(2 Multiframe Period), 3_M_PERIOD(3 Multiframe Period), 4_M_PERIOD(4 Multiframe Period), 5_M_PERIOD(5 Multiframe Period), 6_M_PERIOD(6 Multiframe Period), 7_M_PERIOD(7 Multiframe Period), 8_M_PERIOD(8 Multiframe Period), 9_M_PERIOD(9 Multiframe Period) Unit: 235ms Actual Value Range: 470, 705, 940, 1175, 1410, 1645, 1880, 2115 Default Value: 2_M_PERIOD(2 Multiframe Period)

Issue 01 (2016-09-05)


85


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

NMO

BSC690 0

SET GCELL PSBAS E

GBFD-1 19108

Network Operatio n Mode Support

Meaning: This parameter is related to the paging channel of the system. There are three network operation modes: network operation mode I, network operation mode II, and network operation mode III. Network operation mode I is used when the system is configured with the Gs interface. Network operation mode II is used when the system is not configured with the Gs interface and the PCCCH is not configured. Network operation mode III is used when the system is not configured with the Gs interface and the PCCCH is configured. GUI Value Range: NMOI(Network Operation Mode I), NMOII(Network Operation Mode II), NMOIII(Network Operation Mode III) Unit: None Actual Value Range: NMOI, NMOII, NMOIII Default Value: NMOII(Network Operation Mode II)

NMO

BSC691 0

SET GCELL PSBAS E

GBFD-1 19108

Network Operatio n Mode Support

Meaning: This parameter is related to the paging channel of the system. There are three network operation modes: network operation mode I, network operation mode II, and network operation mode III. Network operation mode I is used when the system is configured with the Gs interface. Network operation mode II is used when the system is not configured with the Gs interface and the PCCCH is not configured. Network operation mode III is used when the system is not configured with the Gs interface and the PCCCH is configured. GUI Value Range: NMOI(Network Operation Mode I), NMOII(Network Operation Mode II), NMOIII(Network Operation Mode III) Unit: None Actual Value Range: NMOI, NMOII, NMOIII Default Value: NMOII(Network Operation Mode II)

GPRS

BSC690 0

SET GCELL GPRS

GBFD-1 14101 GBFD-1 11101

GPRS

Meaning: Whether the current cell supports GPRS.


GUI Value Range: NO(Not support), SupportAsInnPcu(Support as built-in PCU), SupportAsExtPcu(Support as external Pcu) Unit: None Actual Value Range: NO, SupportAsInnPcu, SupportAsExtPcu Default Value: None

Issue 01 (2016-09-05)


86


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

GPRS

BSC691 0

SET GCELL GPRS

GBFD-1 14101

GPRS

Meaning: Whether the current cell supports GPRS.


GUI Value Range: NO(Not support), SupportAsInnPcu(Support as built-in PCU)

GBFD-1 11101

Unit: None Actual Value Range: NO, SupportAsInnPcu Default Value: None

BSSPA GINGC OORDI NATIO N

BSC690 0

SET GCELL PSBAS E

GBFD-1 19305

BSS Paging Coordin ation

Meaning: Whether to support the paging function of the CS domain of the A interface. Yes: the MS can be called upon paging request on the A interface when handling the PS service; No: the MS cannot be called upon paging request on the A interface when handling the PS service. GUI Value Range: NO(NO), YES(YES) Unit: None Actual Value Range: NO, YES Default Value: NO(NO)

BSSPA GINGC OORDI NATIO N

BSC691 0

SET GCELL PSBAS E

GBFD-1 19305

BSS Paging Coordin ation

Meaning: Whether to support the paging function of the CS domain of the A interface. Yes: the MS can be called upon paging request on the A interface when handling the PS service; No: the MS cannot be called upon paging request on the A interface when handling the PS service. GUI Value Range: NO(NO), YES(YES) Unit: None Actual Value Range: NO, YES Default Value: NO(NO)

Issue 01 (2016-09-05)


87


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TransM ode

BSC690 0

SET BTSTR ANS

GBFD-1 13901

Satellite Transmi ssion over Abis Interface

Meaning: This parameter specifies the data transmission mode between the BTS and the BSC. The license control modes are different in different transmission modes. Terrestrial Transmission: The data between the BTS and the BSC is transmitted through the E1 or fiber. This transmission mode has a short delay and is not controlled by the license. Satellite Transmission: The data between the BTS and the BSC is transmitted through the satellite. This transmission mode has a long delay and is controlled by the license. Terrestrial and Satellite: In normal cases, the terrestrial transmission mode is used. When the terrestrial transmission is faulty, the satellite transmission mode is used. This transmission mode is controlled by the license. Pico and Satellite: The data between the BTS3900B and the BSC is transmitted through the satellite. This transmission mode has a long delay and is not controlled by the license. GUI Value Range: TER_TRANS(Terrestrial Transmission), SAT_TRANS(Satellite Transmission), TER_AND_SAT_TRANS(Terrestrial and Satellite), PICO_AND_SAT_TRANS(Pico and Satellite) Unit: None Actual Value Range: TER_TRANS, SAT_TRANS, TER_AND_SAT_TRANS, PICO_AND_SAT_TRANS Default Value: None

Issue 01 (2016-09-05)


88


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TransM ode

BSC691 0

SET BTSTR ANS

GBFD-1 13901

Satellite Transmi ssion over Abis Interface

Meaning: This parameter specifies the data transmission mode between the BTS and the BSC. The license control modes are different in different transmission modes. Terrestrial Transmission: The data between the BTS and the BSC is transmitted through the E1 or fiber. This transmission mode has a short delay and is not controlled by the license. Satellite Transmission: The data between the BTS and the BSC is transmitted through the satellite. This transmission mode has a long delay and is controlled by the license. Terrestrial and Satellite: In normal cases, the terrestrial transmission mode is used. When the terrestrial transmission is faulty, the satellite transmission mode is used. This transmission mode is controlled by the license. Pico and Satellite: The data between the BTS3900B and the BSC is transmitted through the satellite. This transmission mode has a long delay and is not controlled by the license. GUI Value Range: TER_TRANS(Terrestrial Transmission), SAT_TRANS(Satellite Transmission), TER_AND_SAT_TRANS(Terrestrial and Satellite), PICO_AND_SAT_TRANS(Pico and Satellite) Unit: None Actual Value Range: TER_TRANS, SAT_TRANS, TER_AND_SAT_TRANS, PICO_AND_SAT_TRANS Default Value: None

Issue 01 (2016-09-05)


89


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TX

BSC690 0


GBFD-1 10301

Location Updatin g

Meaning:

GBFD-1 11003


Tx-integer (T for short). This parameter specifies the number of timeslots between two transmissions when an MS sends multiple consecutive channel requests. The access algorithm is defined in 3GPP TS 04.08 to reduce the collisions on the RACH and improve the efficiency of the RACH. The algorithm specifies three parameters: Tx-integer (T for short), maximum number of retransmissions (RET), and S related to channel combination. This parameter works with the configuration of the CCCH to determine the parameter S. The relationships between this parameter and the configuration of the CCCH are as follows: When this parameter is set to 3, 8, 14, or 50, S is 55 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 3, 8, 14, or 50, S is 41 if the CCCH and SDCCH share a physical channel. When this parameter is set to 4, 9, or 6, S is 76 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 4, 9, or 6, S is 52 if the CCCH and SDCCH share a physical channel. When this parameter is set to 5, 10, or 20, S is 109 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 5, 10, or 20, S is 58 if the CCCH and SDCCH share a physical channel. When this parameter is set to 6, 11, or 25, S is 163 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 6, 11, or 25, S is 86 if the CCCH and SDCCH share a physical channel. When this parameter is set to 7, 12, or 32, S is 217 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 7, 12, or 32, S is 115 if the CCCH and SDCCH share a physical channel. The timeslot for sending messages is a random value from the collection of {0, 1..., MAX(T, 8)-1}. The number of timeslots (excluding the timeslot used to send messages) between two adjacent channel request messages is a random value from the collection of {S, S+1, ..., S+T-1}.

Issue 01 (2016-09-05)


90


Parame ter ID

NE

MML Comma nd

7 Parameters

Feature ID

Feature Name

Description

When T increases, the interval between two adjacent channel requests increases, and RACH conflicts decrease. When S increases, the interval between two adjacent channel request messages increases, and RACH conflicts decrease, thus improving the usage of AGCH and SDCCH. The access time of the MS, however, is prolonged and the network performance is decreased when T and S increase. Under normal conditions, an appropriate T value should be used to ensure that S is as low as possible, and ensure that AGCH and SDCCH are not overloaded. GUI Value Range: TX_3(3), TX_4(4), TX_5(5), TX_6(6), TX_7(7), TX_8(8), TX_9(9), TX_10(10), TX_11(11), TX_12(12), TX_14(14), TX_16(16), TX_20(20), TX_25(25), TX_32(32), TX_50(50) Unit: None Actual Value Range: TX_3, TX_4, TX_5, TX_6, TX_7, TX_8, TX_9, TX_10, TX_11, TX_12, TX_14, TX_16, TX_20, TX_25, TX_32, TX_50 Default Value: TX_32(32)

Issue 01 (2016-09-05)


91


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TX

BSC691 0


GBFD-1 10301

Location Updatin g

Meaning:

GBFD-1 11003


Tx-integer (T for short). This parameter specifies the number of timeslots between two transmissions when an MS sends multiple consecutive channel requests. The access algorithm is defined in 3GPP TS 04.08 to reduce the collisions on the RACH and improve the efficiency of the RACH. The algorithm specifies three parameters: Tx-integer (T for short), maximum number of retransmissions (RET), and S related to channel combination. This parameter works with the configuration of the CCCH to determine the parameter S. The relationships between this parameter and the configuration of the CCCH are as follows: When this parameter is set to 3, 8, 14, or 50, S is 55 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 3, 8, 14, or 50, S is 41 if the CCCH and SDCCH share a physical channel. When this parameter is set to 4, 9, or 6, S is 76 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 4, 9, or 6, S is 52 if the CCCH and SDCCH share a physical channel. When this parameter is set to 5, 10, or 20, S is 109 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 5, 10, or 20, S is 58 if the CCCH and SDCCH share a physical channel. When this parameter is set to 6, 11, or 25, S is 163 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 6, 11, or 25, S is 86 if the CCCH and SDCCH share a physical channel. When this parameter is set to 7, 12, or 32, S is 217 if the CCCH and SDCCH do not share a physical channel. When this parameter is set to 7, 12, or 32, S is 115 if the CCCH and SDCCH share a physical channel. The timeslot for sending messages is a random value from the collection of {0, 1..., MAX(T, 8)-1}. The number of timeslots (excluding the timeslot used to send messages) between two adjacent channel request messages is a random value from the collection of {S, S+1, ..., S+T-1}.

Issue 01 (2016-09-05)


92


Parame ter ID

NE

MML Comma nd

7 Parameters

Feature ID

Feature Name

Description

When T increases, the interval between two adjacent channel requests increases, and RACH conflicts decrease. When S increases, the interval between two adjacent channel request messages increases, and RACH conflicts decrease, thus improving the usage of AGCH and SDCCH. The access time of the MS, however, is prolonged and the network performance is decreased when T and S increase. Under normal conditions, an appropriate T value should be used to ensure that S is as low as possible, and ensure that AGCH and SDCCH are not overloaded. GUI Value Range: TX_3(3), TX_4(4), TX_5(5), TX_6(6), TX_7(7), TX_8(8), TX_9(9), TX_10(10), TX_11(11), TX_12(12), TX_14(14), TX_16(16), TX_20(20), TX_25(25), TX_32(32), TX_50(50) Unit: None Actual Value Range: TX_3, TX_4, TX_5, TX_6, TX_7, TX_8, TX_9, TX_10, TX_11, TX_12, TX_14, TX_16, TX_20, TX_25, TX_32, TX_50 Default Value: TX_32(32) Channe lDynAd justOpt

BSC690 0

SET BSCEX SOFTP ARA

None

None

Meaning: Whether to enable the dynamic channel adjustment optimization procedure. If this parameter is set to ON(On), the BSC sends the BTS a message indicating dynamic channel adjustment through the RSL. If this parameter is set to OFF(Off), the BSC sends the BTS a message indicating dynamic channel adjustment through the OML.eGBTS does not support this parameter. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: ON(On)

Issue 01 (2016-09-05)


93


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

Channe lDynAd justOpt

BSC691 0

SET BSCEX SOFTP ARA

None

None

Meaning: Whether to enable the dynamic channel adjustment optimization procedure. If this parameter is set to ON(On), the BSC sends the BTS a message indicating dynamic channel adjustment through the RSL. If this parameter is set to OFF(Off), the BSC sends the BTS a message indicating dynamic channel adjustment through the OML.eGBTS does not support this parameter. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: ON(On)

Issue 01 (2016-09-05)


94


8 Counters

8

Counters

There are no specific counters associated with this feature.

Issue 01 (2016-09-05)


95


9 Glossary

9

Glossary

For the acronyms, abbreviations, terms, and definitions, see Glossary.

Issue 01 (2016-09-05)


96


10 Reference Documents

10

Reference Documents

None

Issue 01 (2016-09-05)


97

DSON(GBSS19.0_01)

Recommend Documents