I received these from my friend. no guarantee of accuracy is assumed.Full description
RemLawFull description
Disaster Risk Reduction and Management Sample Highschool Exam
cswa
Prometric Exam 2
Descripción completa
Power Electronics Examination questions to help students prepare for their mid-terms and final examinations at both undergraduate and graduate levelFull description
hihiFull description
Full description
SolidWorks Corporation: CSWP Sample Exam Certified SolidWorks Professional: Advanced Mold Tool (CSWP-MTLS) These questions are an example of what to expect on the Advanced Mold Tools exam. How to take this sample exam: 1. To best simulate the condition of the real test, it is best NOT to print this exam. Since the Virtual Tester client window runs concurrently with SolidWorks you must switch back and forth between the two applications. Keeping this document open and consulting it on your computer while running SolidWorks is the best method to simulate the real test conditions. 2. The multiple choice answers should serve as a check for you to ensure that your model is co rrect while completing this exam. If you do not find your answer in the selections offered then there is most likely something wrong with your model. 3. Answers to the sample questions can be found on the last page of this document. 4. If you can complete this exam in 30 minutes or less, you should be re ady to take the real exam. What you will need for the real CSWP-MTLS exam: 1. 2. 3. 4.
A computer running SolidWorks 2008 or later (Student version 2009 or later). The computer must have a connection to the internet. Dual monitors will help, but are not necessary. If you choose to run the Virtual Tester client on a different com puter, you must have a way to transfer files to the SolidWorks computer, like a USB thumb drive or similar method.
The exam covers these areas: A. B. C. D.
Parting line creation Imported part repair using basic surface tools Shut-off face creation Draft Analysis tool
The sample exam begins on the next page
Problem 1 Create a cavity block for the part “bracket” found in the zip file of this sample exam. Use the parting line tool to create the shut off surface for the part, and then create the cavity block.
Parameters: Cavity Block Material: Cast Stainless Steel Density: .27818 lb/in^3 (stock SolidWorks Material density) Units: Inches Mass: Pounds A= 3.125 B= 4.625 C= 10.000 D= 10.000 What is the mass of the cavity block in pounds? A. 107.078
B. 107.028 C. 107.538 D. 107.052
Hint: You must use the parting line tool to get the correct parting line especially in the transition areas where the part changes angles. If you try to fake the parting line the part will not get split at the correct location, and the mass of your cavity block will be off. Don’t forget to always add the correct material to your cavity block to ensure the mass is correct. In the real exam this is not a multiple choice question and you are only allowed a .015 lbs tolerance on the resulting mass of the block.
Continued on next page
Problem 2 Perform a draft Analysis on the bracket part. Direction of pull: Top Plane Draft Angle: 1.00 Degrees
How many negative draft faces does the part have? A. 16 B. 15 C. 0 D. 17
Hint: Make sure you understand the available options in the Draft Analysis tool.
Continued on next page
Problem 3 Shut-off face creation Open the part “Puck” found in the zip file of this sample exam and c reate shut-off faces for the five openings as shown below:
Without Shut-off faces
With Shut-off faces
What is the measured surface area of the five shut-off faces in inches ^2? A. 1.9634 B. 1.9242 C. 1.9315 D. 1.9245 Hint: Use the measuring tool to get the surface area calculation. Also using the Shutoff faces tool will automate the face creation process to save you some time.