CPRI MUX(SRAN12.1_01)

SingleRAN SRAN12.1

CPRI MUX Feature Parameter Description Issue

01

Date

2017-03-10

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2017. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd. Address:

Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China

Website:

http://www.huawei.com

Email:

[email protected]

Issue 01 (2017-03-10)

Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

i

SingleRAN CPRI MUX Feature Parameter Description

Contents

Contents 1 About This Document.................................................................................................................. 1 1.1 Scope.............................................................................................................................................................................. 1 1.2 Intended Audience.......................................................................................................................................................... 1 1.3 Change History............................................................................................................................................................... 1 1.4 Differences Between Base Station Types....................................................................................................................... 2

2 Overview......................................................................................................................................... 3 2.1 Introduction.................................................................................................................................................................... 3 2.2 Benefits........................................................................................................................................................................... 4

3 BBUs and Boards That Support CPRI MUX............................................................................ 5 3.1 BBU3900 Boards That Support CPRI MUX................................................................................................................. 6 3.2 BBU3910 Boards That Support CPRI MUX................................................................................................................. 8 3.3 BBU3910As That Support CPRI MUX......................................................................................................................... 9

4 CPRI Topology Principles for a Multimode Base Station...................................................11 5 Star Topology with CPRI MUX (BBU3900)............................................................................ 12 5.1 Co-MPT Scenarios....................................................................................................................................................... 12 5.1.1 Constraints................................................................................................................................................................. 12 5.1.2 UL CPRI MUX in Star Topology..............................................................................................................................12 5.1.3 GU/GL CPRI MUX in Star Topology....................................................................................................................... 14 5.1.4 GUL CPRI MUX in Star Topology........................................................................................................................... 20 5.2 Separate-MPT Scenarios.............................................................................................................................................. 24 5.2.1 Constraints................................................................................................................................................................. 24 5.2.2 UL CPRI MUX in Star Topology..............................................................................................................................24 5.2.3 GU/GL CPRI MUX in Star Topology....................................................................................................................... 25

6 Star Topology with CPRI MUX (BBU3910)............................................................................ 27 6.1 Co-MPT Scenarios....................................................................................................................................................... 27 6.2 Separate-MPT Scenarios.............................................................................................................................................. 29

7 Star Topology with CPRI MUX (BBU3910A)......................................................................... 33 8 Chain Topology with CPRI MUX............................................................................................ 34 9 CPRI MUX Trunk Chain Topology (RMU3900A).................................................................37 9.1 Co-MPT Scenarios....................................................................................................................................................... 37 Issue 01 (2017-03-10)


ii


Contents

9.2 Separate-MPT Scenarios.............................................................................................................................................. 38

10 CPRI MUX with Multimode Load Sharing Topology....................................................... 39 11 Triple-Mode Dual-Star Topology.......................................................................................... 41 11.1 GU+L Dual-Star Topology......................................................................................................................................... 42 11.2 GL+U Dual-Star Topology......................................................................................................................................... 42 11.3 G[U*L] Dual-Star Topology.......................................................................................................................................43

12 Specifications of the CPRI MUX Feature..............................................................................44 12.1 Converging Capabilities............................................................................................................................................. 44 12.2 Cascading Level of the Chain Topology Using the CPRI MUX Feature...................................................................49

13 Related Features.........................................................................................................................50 13.1 Prerequisite Features...................................................................................................................................................50 13.2 Mutually Exclusive Features...................................................................................................................................... 50 13.3 Impacted Features.......................................................................................................................................................51

14 Network Impact......................................................................................................................... 52 14.1 System Capacity......................................................................................................................................................... 52 14.2 Network Performance.................................................................................................................................................52 14.3 Reliability................................................................................................................................................................... 52

15 Engineering Guidelines........................................................................................................... 54 15.1 When to Use............................................................................................................................................................... 55 15.2 Required Information................................................................................................................................................. 55 15.3 Network Planning....................................................................................................................................................... 55 15.4 Deployment................................................................................................................................................................ 56 15.4.1 Requirements........................................................................................................................................................... 56 15.4.2 Data Preparation...................................................................................................................................................... 56 15.4.3 Activation................................................................................................................................................................ 59 15.4.4 Activation Observation............................................................................................................................................62 15.4.5 Deactivation.............................................................................................................................................................63 15.4.6 Reconfiguration....................................................................................................................................................... 63 15.5 Performance Monitoring.............................................................................................................................................64 15.6 Parameter Optimization.............................................................................................................................................. 64 15.7 Possible Issues............................................................................................................................................................ 64 15.7.1 Related Alarms........................................................................................................................................................ 64 15.7.2 MML Commands for Maintenance......................................................................................................................... 67

16 Parameters................................................................................................................................... 69 17 Counters...................................................................................................................................... 85 18 Glossary....................................................................................................................................... 86 19 Reference Documents............................................................................................................... 87

Issue 01 (2017-03-10)


iii


1 About This Document

1

About This Document

1.1 Scope This document describes the working principles and engineering guidelines of the CPRI MUX feature. This document applies to macro base stations, including BTS3900, BTS3900L, BTS3900A, BTS3900AL, BTS3900C, and DBS3900. Any parameters, alarms, counters, or managed objects (MOs) described herein apply only to the corresponding software release. For future software releases, refer to the corresponding updated product documentation. Any "LTE" in this document refers to LTE FDD, and "eNodeB" refers to LTE FDD eNodeB. In addition, "G", "U", and "L" in RAT acronyms refer to GSM, UMTS, and LTE FDD, respectively.

1.2 Intended Audience This document is intended for personnel who: l

Need to understand the features described herein

l

Work with Huawei products

1.3 Change History This section provides information about the changes in different document versions. There are two types of changes: l

Feature change Changes in features and parameters of a specified version as well as the affected entities

l

Editorial change Changes in wording or addition of information and any related parameters affected by editorial changes. Editorial change does not specify the affected entities.

Issue 01 (2017-03-10)


1


1 About This Document

SRAN12.1 01 (2017-03-10) This issue does not include any changes.

SRAN12.1 Draft A (2016-12-31) Draft A (2016-12-31) of SRAN12.1 introduces the following changes to Issue 02 (2016-04-20) of SRAN11.1. Change Type

Change Description

Parameter Change

Feature change

Supported the following relationships between the converged boards and converging boards in UL separateMPT scenarios:

None

l One-to-one relationship A converged board corresponds to a converging board. A maximum of three pairs of one-to-one relationships are supported. l One-to-two relationship A converged board corresponds to two converging boards. A maximum of two pairs of one-to-two relationships are supported. For details, see 6.2 Separate-MPT Scenarios. Editorial change

Deleted the description "In separate-MPT scenarios, CPRI MUX is used as a special solution." in 4 CPRI Topology Principles for a Multimode Base Station.

None

Added an example to 13.2 Mutually Exclusive Features.

None

1.4 Differences Between Base Station Types This document applies only to 3900 series base stations, excluding DBS3900 LampSite base stations. For application of the CPRI MUX feature in the DBS3900 LampSite base stations, see CPRI MUX (LampSite) Feature Parameter Description.

Issue 01 (2017-03-10)


2


2 Overview

2

Overview

2.1 Introduction In the CPRI MUX feature, multiple modes use a common public radio interface (CPRI) link to transmit data. Multimode RF modules are connected to a single-mode or multimode(1) baseband processing board/interface board through CPRI links. Another single-mode or multimode(1) baseband processing board/interface board is connected to the previous baseband processing board/ interface board through the BBU backplane and indirectly communicates with the multimode RF modules. The baseband processing board or interface board that is directly connected to multimode RF modules is called the converging board, and the corresponding mode is called the converging party. The baseband processing board or interface board that is indirectly connected to multimode RF modules is called the converged board, and the corresponding mode is called the converged party. In Figure 2-1, mode A is the converged party and mode B is the converging party. Note that mode A and mode B can be a single mode or co-BBP multiple modes.(1) Figure 2-1 Working principle of CPRI MUX

Issue 01 (2017-03-10)


3


2 Overview

NOTE

l

(1)

UBBP boards are added in SRAN9.0, which support multimode co-BBP. Therefore, a UBBP board can serve as both the converging board and converged board.

l Only multimode RF modules support CPRI MUX. Single-mode RF modules do not support CPRI MUX. l The modes of RF modules in the figures at chapters 4, 5, and 6 refer to the working modes of RF modules, not the supporting modes of RF modules.

2.2 Benefits This feature provides the following benefits: l

Reduced cable purchase, installation, and maintenance costs for newly deployed multimode base stations: Multiple modes can use a CPRI link to transmit data, and therefore the number of required optical modules and fiber optic cables decreases considerably.

l

Lower engineering costs and shorter service interruption duration in refarming scenarios: If a multimode RF module uses a single CPRI cable, newly deployed modes can share the module and the cable after refarming.

l

Guaranteed coverage for cascaded multimode RF modules: CPRI MUX allows multimode RF modules to be cascaded to ensure coverage along highways and railways.

Issue 01 (2017-03-10)


4


3

3 BBUs and Boards That Support CPRI MUX

BBUs and Boards That Support CPRI MUX

From SRAN10.0 onwards, BBUs that support CPRI MUX include the BBU3900, BBU3910, and BBU3910A. l

Section 3.1 BBU3900 Boards That Support CPRI MUX describes the BBU3900 boards that support CPRI MUX.

l

Section 3.2 BBU3910 Boards That Support CPRI MUX describes the BBU3910 boards that support CPRI MUX.

l

Section 3.3 BBU3910As That Support CPRI MUX describes the BBU3910A that supports CPRI MUX.

Issue 01 (2017-03-10)


5



3.1 BBU3900 Boards That Support CPRI MUX In separate-MPT scenarios, only UMTS and LTE can serve as the converging party. If GSM is involved in the scenarios, GSM baseband signals are processed by RF modules. Table 3-1 lists BBU3900 boards that support the CPRI MUX feature in a separate-MPT multimode base station and constraints on the slots of the converging and converged boards. Table 3-1 BBU3900 boards that support the CPRI MUX feature in a separate-MPT multimode base station and constraints on the slots of the converging and converged boards Mode on the CPRI Port

Converging Board

Slot of the Converging Board

Converged Board

Slot of the Converged Board

UL

WBBPf/ UBBP_U

Slot 2 or 3

LBBPd/ UBBP_L

One LBBPd or UBBP_L must be installed in slot 3 or 2.

LBBPd/ UBBP_L

Slot 2 or 3

WBBPa/ WBBPb/ WBBPd/ WBBPf/ UBBP_U

One WBBPf or UBBP_U must be installed in slot 3 or 2.

GU

WBBPf/ UBBP_U

Slot 2 or 3

GTMUb/ GTMUc

Slot 6

GL

LBBPd/ UBBP_L

Slot 2 or 3

GTMUb/ GTMUc

Slot 6

In co-MPT scenarios, any one or multiple modes of GSM, UMTS, and LTE can serve as the converging party or converged party. Table 3-2 lists BBU3900 boards that support the CPRI MUX feature in a co-MPT multimode base station and constraints on the slots of the converging and converged boards. Table 3-2 BBU3900 boards that support the CPRI MUX feature in a co-MPT multimode base station and constraints on networking Mode on the CPRI Port

Converging Board

Slot of the Convergin g Board

Constraints on Networking

UL

WBBPf, LBBPd, or UBBP_U/L/GU/GL/ UL/GUL(1)(2)

Slot 2 or 3

l When LTE serves as the converged party, the LBBPc cannot serve as the converged board. l One WBBPf or UBBP_Ux(3) needs to be installed in slot 2 or 3.

Issue 01 (2017-03-10)


6



Mode on the CPRI Port

Converging Board



GU

UBRIb(4)

Slot 0 or 1

UBBP_G/U/GU/GL/ UL/GUL

Slot 2 or 3

l When LTE serves as the converged party, the LBBPc cannot serve as the converged board. l When the converging party or converged party contains UMTS, one WBBPf or UBBP_Ux needs to be installed in slot 2 or 3. l When a UBRIb serves as the converging board, GSM baseband signals are processed by RF modules. (5)

l When a UBRIb serves as the converging board in GUL CPRI MUX, the converged boards must be UO and LO baseband processing boards.(6) l When a BBU is configured with a multimode co-BBP board, and modes used in CPRI MUX are the same as or are the subset of the modes on the coBBP board, RF modules are connected to CPRI ports on the multimode coBBP board. For example, if the BBU is configured with a UBBP_GL, implement GL CPRI MUX on this UBBP_GL instead of a GO or LO baseband processing board. l When GSM baseband signals are processed by RF modules and GSM serves as the converged party, GSM signals can be converged by the UBBP_U/UL. Therefore, a GSM baseband processing board or interface board is not required. l If GSM baseband signals are not processed by RF modules(7), a UBBP_Gx(3) must be installed in slot 1, 2, or 3. GL

Issue 01 (2017-03-10)

UBRIb

Slot 1

UBBP_G/L

Slot 1, 2, or 3

Same as those for GU


7



GUL


Converging Board


UBBP_GU/GL/UL/G UL

Slot 2 or 3

UBRIb

Slot 1

UBBP_G/U/L/GU/G L/UL/GUL

Slot 2 or 3


Same as those for GU

NOTE

l

(1)

l

(2) When multiple modes are deployed on a UBBP, the mode of data transmitted through CPRI ports on this board can be one of or all of the deployed modes. For example, the mode of data transmitted through the CPRI ports on a UBBP_GUL can be UMTS or UL.

l

(3) A

l

(4)

l

(5)

l

(6) When

l

(7) If GSM baseband signals are not processed by RF modules, the signals are processed on the UBBP_Gx in the BBU. Therefore, a UBBP_Gx must be configured.

If a baseband processing board is named UBBP_A/B/C, "A", "B", "C" indicates the mode whose baseband resources are configured on this board, baseband resources of different modes are isolated by "/". For example, UBBP_G/U/GU indicates a UBBP configured with GSM baseband resources, UMTS baseband resources, or GSM and UMTS baseband resources (GU co-BBP).

UBBP_Ux indicates that this UBBP serves UMTS and other modes; a UBBP_Gx indicates that this UBBP serves GSM and other modes. If the data rate of a CPRI port on a UBRIb board is greater than 4.9 Gbit/s, the port can carry services of only one RAT in versions earlier than SRAN11.1 and carry services of two RATs in SRAN11.1 and later versions.

If GSM baseband signals are processed by RRUs, the signals do not need to be processed on the baseband processing board (UBBP_Gx) in the BBU. a UBRIb serves as the converging board in GUL CPRI MUX, cells served by the converged UO and LO modes must be configured on the specified baseband equipment group, and such a baseband equipment group must be configured with single-mode baseband processing boards.

3.2 BBU3910 Boards That Support CPRI MUX In separate-MPT scenarios, only UMTS and LTE can serve as the converging party. If GSM is involved in the scenarios, GSM baseband signals are processed by RF modules. Table 3-3 lists the BBU3910 boards that support the CPRI MUX feature and the slot assignment. Table 3-3 BBU3910 boards that support the CPRI MUX feature and the slot assignment for separate-MPT multimode base stations

Issue 01 (2017-03-10)


Converging Board


Converged Board


UL

UBBP_U

Slot 0, 1, 2, 3, 4, or 5

UBBP_L

Slot 0, 1, 2, 3, 4, or 5


8




Converging Board


Converged Board


UBBP_L

Slot 0, 1, 2, 3, 4, or 5

UBBP_U

Slot 0, 1, 2, 3, 4, or 5

UBBPei_U

Slot 0, 1, 2, 3, 4, or 5

UBBPd/ UBBPe_L

Slot 0, 1, 2, 3, 4, or 5

UBBPei_L

Slot 0, 1, 2, 3, 4, or 5

UBBPd/ UBBPe_U

Slot 0, 1, 2, 3, 4, or 5

GU

UBBP_U

Slot 0, 1, 2, or 3

GTMUb/ GTMUc

Slot 6

GL

UBBP_L

Slot 0, 1, 2, or 3

GTMUb/ GTMUc

Slot 6

UL

NOTE

In separate-MPT scenarios, the UBBPei cannot serve as a converged board.

In co-MPT scenarios, any one or multiple modes of GSM, UMTS, and LTE can serve as the converging party or converged party. Table 3-4 lists the BBU3910 boards that support the CPRI MUX feature and the slot assignment. Table 3-4 BBU3910 boards that support the CPRI MUX feature and the slot assignment for co-MPT multimode base stations Mode on the CPRI Port

Converging Board


GU

UBRIb or UBBP_G/U/L/GU/GL/UL/GU L

Slot 0, 1, 2, 3, 4, or 5

GL UL GUL

NOTE

If the data rate of a CPRI port on a UBRIb board is greater than 4.9 Gbit/s, the port can carry services of only one RAT in versions earlier than SRAN11.1; the port can carry services of two RATs in SRAN11.1 and later versions.

3.3 BBU3910As That Support CPRI MUX The BBU3910A only applies to co-MPT scenarios. A BBU3910A provides six CPRI ports, and all BBU3910As support CPRI MUX. Table 3-5 lists the modes supported by different models of BBU3910As. Issue 01 (2017-03-10)


9



Table 3-5 Modes supported by BBU3910As

Issue 01 (2017-03-10)

BBU Model

Mode

BBU3910A1

GU, GL, UL

BBU3910A2

GU, GL, UL

BBU3910A3

GU, GL, UL, GUL


10


4

4 CPRI Topology Principles for a Multimode Base Station

CPRI Topology Principles for a Multimode Base Station l

The dual-star topology is recommended for a separate-MPT base station.

l

The star topology with CPRI MUX is recommended for a co-MPT base station.

l

The multimode load sharing topology is recommended when the CPRI bandwidth is insufficient or a separate-MPT base station using the dual-star topology is reconstructed to a co-MPT base station.

l

The chain topology with CPRI MUX, where multimode RF modules are cascaded, is recommended for base stations deployed in stadiums, metros, and high-speed railways.

l

The RMU solution supports only the trunk chain topology with CPRI MUX.

Issue 01 (2017-03-10)


11


5

5 Star Topology with CPRI MUX (BBU3900)

Star Topology with CPRI MUX (BBU3900)

5.1 Co-MPT Scenarios 5.1.1 Constraints The converging and converged parties in the CPRI MUX feature must share one BBU.

5.1.2 UL CPRI MUX in Star Topology l

Scenario 1: A single-mode baseband processing board serves as the converging board. The following conditions must be met: –

A WBBPf, LBBPd, or UBBP_U/L serves as the converging board and is configured in slot 2 or 3.

–

When LTE serves as the converged party, the LBBPc cannot serve as the converged board.

–

When UMTS serves as the converging or converged party, one WBBPf or UBBP_Ux must be installed in slot 2 or 3.

Figure 5-1 shows CPRI MUX where a WBBPf/UBBP_U serves as the converging board and an LBBPd/UBBP_L serves as the converged board.

Issue 01 (2017-03-10)


12



Figure 5-1 UL CPRI MUX in co-MPT scenarios when UMTS serves as the converging party

l

Scenario 2: A co-BBP board serves as the converging board. The following conditions must be met: –

A UBBP_GU/GL/UL/GUL serves as the converging board and is configured in slot 2 or 3.

–

When a UBBP_GU serves as the converging board in UL CPRI MUX, UMTS is the converging party, and LTE is the converged party, the LBBPc cannot serve as the converged board.

–

When a UBBP_GL serves as the converging board in UL CPRI MUX, LTE is the converging party and UMTS is the converged party. A WBBPf or UBBP_Ux is configured in slot 2 or 3.

–

When a UBBP_UL serves as the converging board in UL CPRI MUX, the UBBP_UL can provide CPRI ports for transmitting UL data.

Figure 5-2 shows UL CPRI MUX where the UBBP_UL is configured in slot 3.

Issue 01 (2017-03-10)


13



Figure 5-2 UL CPRI MUX in co-MPT scenarios with UL co-BBP

5.1.3 GU/GL CPRI MUX in Star Topology GU CPRI MUX in Star Topology l


A UBRIb or UBBP_G/U serves as the converging board. The UBRIb is configured in slot 0 or 1, and the UBBP_G/U is configured in slot 2 or 3.

–


–

When a UBRIb serves as the converging board, GSM baseband signals are processed by RF modules.

–

When GSM baseband signals are processed by RF modules and GSM serves as the converged party, GSM signals can be converged by the UBBP_U. Therefore, a GSM baseband processing board or interface board is not required.

–

If GSM baseband signals are not processed by RF modules, a UBBP_Gx is configured in slot 1, 2, or 3.

Figure 5-3 shows GU CPRI MUX where GSM serves as the converging party, a UBRIb serves as the converging board, and GSM baseband signals are processed by RF modules.

Issue 01 (2017-03-10)


14



Figure 5-3 GU CPRI MUX in co-MPT scenarios when GSM serves as the converging party, a UBRIb serves as the converging board, and GSM baseband signals are processed by RF modules

Figure 5-4 shows GU CPRI MUX where UMTS serves as the converging party, a UBBP_U serves as the converging board, and GSM baseband signals are processed by RF modules.

Issue 01 (2017-03-10)


15



Figure 5-4 GU CPRI MUX in co-MPT scenarios when UMTS serves as the converging party, a UBBP_U serves as the converging board, and GSM baseband signals are processed by RF modules

l



–

When a UBBP_GL serves as the converging board in GU CPRI MUX, GSM is the converging party and UMTS is the converged party. A WBBPf or UBBP_Ux is configured in slot 2 or 3.

–

When a UBBP_UL serves as the converging board in GU CPRI MUX, UMTS is the converging party and GSM is the converged party. If GSM baseband signals are processed by RF modules, the GSM signals can be converged by a UBBP_UL, so a GSM baseband processing board or interface board is not required. If GSM baseband signals are not processed by RF modules, a UBBP_Gx is configured in slot 1, 2 or 3.

–

When a UBBP_GU/GUL serves as the converging board in GU CPRI MUX, a single board can provide CPRI ports for transmitting GU data.

Figure 5-5 shows GU CPRI MUX where the UBBP_GU is configured in slot 3.

Issue 01 (2017-03-10)


16



Figure 5-5 GU CPRI MUX in co-MPT scenarios with GU co-BBP

GL CPRI MUX in Star Topology l


A UBRIb or UBBP_G/L serves as the converging board. The UBRIb is configured in slot 1, and the UBBP_G/L is configured in slot 1, 2, or 3.

–


–


–

When GSM baseband signals are processed by RF modules and GSM serves as the converged party, GSM signals can be converged by the UBBP_L. Therefore, a GSM baseband processing board or interface board is not required.

–

If GSM baseband signals are not processed by RF modules, a UBBP_Gx is configured in slot 1, 2, or 3.

Figure 5-6 shows GL CPRI MUX where GSM serves as the converging party, a UBRIb serves as the converging board, and GSM baseband signals are processed by RF modules.

Issue 01 (2017-03-10)


17



Figure 5-6 GL CPRI MUX in co-MPT scenarios when GSM serves as the converging party, a UBRIb serves as the converging board, and GSM baseband signals are processed by RF modules

Figure 5-7 shows GL CPRI MUX where LTE serves as the converging party, a UBBP_L serves as the converging board, and GSM baseband signals are processed by RF modules.

Issue 01 (2017-03-10)


18



Figure 5-7 GL CPRI MUX in co-MPT scenarios when LTE serves as the converging party, a UBBP_L serves as the converging board, and GSM baseband signals are processed by RF modules

l



–

When a UBBP_GU serves as the converging board in GL CPRI MUX, GSM is the converging party and LTE is the converged party. In this case, the LBBPc cannot serve as the converged board.

–

When a UBBP_UL serves as the converging board in GL CPRI MUX, LTE is the converging party and GSM is the converged party. If GSM baseband signals are processed by RF modules, the GSM signals can be converged by a UBBP_UL, so a GSM baseband processing board or interface board is not required. If GSM baseband signals are not processed by RF modules, a UBBP_Gx is configured in slot 1, 2 or 3.

–

When a UBBP_GL/GUL serves as the converging board in GL CPRI MUX, a single board can provide CPRI ports for transmitting GL data.

Figure 5-8 shows GL CPRI MUX where the UBBP_GL is configured in slot 3.

Issue 01 (2017-03-10)


19



Figure 5-8 GL CPRI MUX in co-MPT scenarios with GL co-BBP

5.1.4 GUL CPRI MUX in Star Topology l


A UBRIb or UBBP_G/U/L serves as the converging board. The UBRIb is configured in slot 1, and the UBBP_G/U/L is configured in slot 2 or 3.

–


–


–


–

When a UBRIb serves as the converging board in GUL CPRI MUX, the converged boards are UO and LO baseband processing boards(1), that is, WBBP(2)/UBBP_U and LBBPd/UBBP_L.

–

When GSM baseband signals are processed by RF modules and GSM serves as the converged party, GSM signals can be converged by the UBBP_U/L. Therefore, a GSM baseband processing board or interface board is not required.

–

If GSM baseband signals are not processed by RF modules, a UBBP_Gx is configured in slot 1, 2, or 3. NOTE

Issue 01 (2017-03-10)

l

(1)

l

(2)

In this scenario, cells served by the converged UO and LO modes must be configured on the specified baseband equipment group, and such a baseband equipment group must be configured with single-mode baseband processing boards. WBBP refers to WBBPa, WBBPb, WBBPd, or WBBPf.


20



Figure 5-9 shows GUL CPRI MUX where GSM serves as the converging party, a UBRIb serves as the converging board, and GSM baseband signals are processed by RF modules. Figure 5-9 GUL CPRI MUX in co-MPT scenarios when GSM serves as the converging party, a UBRIb serves as the converging board, and GSM baseband signals are processed by RF modules

Figure 5-10 shows GUL CPRI MUX where UMTS serves as the converging party and GSM baseband signals are processed by RF modules.

Issue 01 (2017-03-10)


21



Figure 5-10 GUL CPRI MUX in co-MPT scenarios where UMTS serves as the converging party and GSM baseband signals are processed by RF modules

l



–

A WBBPf or UBBP_Ux is configured in slot 2 or 3.

–

When a UBBP_GU serves as the converging board in GUL CPRI MUX, GU is the converging party, and LTE is the converged party. In this case, the LBBPc cannot serve as the converged board.

–

When a UBBP_GL serves as the converging board in GUL CPRI MUX, GL is the converging party and UMTS is the converged party. A WBBPf or UBBP_Ux is configured in slot 2 or 3.

–

When a UBBP_UL serves as the converging board in GUL CPRI MUX, UL is the converging party and GSM is the converged party. If GSM baseband signals are processed by RF modules, the GSM signals can be converged by a UBBP_UL, so a GSM baseband processing board or interface board is not required. If GSM baseband signals are not processed by RF modules, a UBBP_Gx is configured in slot 1, 2 or 3.

–

When a UBBP_GUL serves as the converging board in GUL CPRI MUX, a single board can provide CPRI ports for transmitting GUL data.

Figure 5-11 shows GUL CPRI MUX where UL serves as the converging party and GSM baseband signals are processed by RF modules.

Issue 01 (2017-03-10)


22



Figure 5-11 GUL CPRI MUX in co-MPT scenarios where UL serves as the converging party and GSM baseband signals are processed by RF modules

Figure 5-12 shows GUL CPRI MUX where the UBBP_GUL is configured in slot 3. Figure 5-12 GUL CPRI MUX in co-MPT scenarios with GUL co-BBP

Issue 01 (2017-03-10)


23



5.2 Separate-MPT Scenarios 5.2.1 Constraints l

The converging and converged parties in the CPRI MUX feature must share one BBU.

l

Data convergence is allowed only between two modes in the same BBU. Each mode can only converge data or have its data converged. Data can only be converged to one board at a time.

l

A BBU can provide a maximum of six CPRI ports for data convergence, and the CPRI ports must be provided by a WBBPf, LBBPd, or UBBP_U/L that is installed in slot 2 or slot 3.

5.2.2 UL CPRI MUX in Star Topology l

If UMTS is the converging party and LTE is the converged party, the converging board must be a WBBPf/UBBP_U and the WBBPf/UBBP_U must be installed in slot 2 or 3. The converged board must be an LBBPd/UBBP_L and one LBBPd/UBBP_L must be installed in slot 3 or 2, as shown in Figure 5-13.

l

If LTE is the converging party and UMTS is the converged party, the converging board must be an LBBPd/UBBP_L and the LBBPd/UBBP_L must be installed in slot 2 or 3. The converged board can be a WBBPa/WBBPb/WBBPd/WBBPf/UBBP_U, and one WBBPf/UBBP_U must be installed in slot 3 or 2, as shown in Figure 5-14.

Figure 5-13 UL CPRI MUX in separate-MPT scenarios when UMTS is the converging party

Issue 01 (2017-03-10)


24



Figure 5-14 UL CPRI MUX in separate-MPT scenarios when LTE is the converging party

5.2.3 GU/GL CPRI MUX in Star Topology l

In GU CPRI MUX, the converging party must be UMTS, and the converged party must be GSM. The converging board must be a WBBPf or UBBP_U and must be installed in slot 2 or 3, and the converged board must be a GTMUb or GTMUc and must be installed in slot 6, as shown in Figure 5-15.

l

In GL CPRI MUX, LTE must serve as the converging party and GSM must serve as the converged party. The converging board must be an LBBPd or UBBP_L and must be installed in slot 2 or 3, and the converged board must be a GTMUb or GTMUc and must be installed in slot 6, as shown in Figure 5-16.

NOTICE In this scenario, data from slot 6 can be converged to either slot 2 or 3, but cannot be converged to both slots.

Issue 01 (2017-03-10)


25



Figure 5-15 Separate-MPT GU CPRI MUX

Figure 5-16 Separate-MPT GL CPRI MUX

Issue 01 (2017-03-10)


26


6


Star Topology with CPRI MUX (BBU3910)

6.1 Co-MPT Scenarios In co-MPT scenarios, the following conditions must be met if BBU3910s support CPRI MUX: l

The converging and converged parties in the CPRI MUX feature share one BBU.

l

A UBRIb or UBBP_G/U/L/GU/GL/UL/GUL board can serve as the converging board, and is installed in one of slots 0 to 5.

l


l

When GSM baseband signals are processed by RF modules and GSM serves as the converged party, GSM signals can be converged by the UBBP_U/L/UL. Therefore, a GSM baseband processing board or interface board is not required.

Use GU CPRI MUX as an example: l

Figure 6-1 shows co-MPT GU CPRI MUX where a UBRIb serves as the converging board.

l

Figure 6-2 shows co-MPT GU CPRI MUX where a UBBP_U serves as the converging board.

l

Figure 6-3 shows co-MPT GU CPRI MUX where a UBBP_GU serves as the converging board.

Issue 01 (2017-03-10)


27



Figure 6-1 Co-MPT GU CPRI MUX where a UBRIb serves as the converging board

Figure 6-2 Co-MPT GU CPRI MUX where a UBBP_U serves as the converging board

Issue 01 (2017-03-10)


28



Figure 6-3 Co-MPT GU CPRI MUX where a UBBP_GU serves as the converging board

6.2 Separate-MPT Scenarios Constraints l


l

Data convergence is allowed only between two modes in the same BBU. Each mode can only converge data or have its data converged.

l

In separate-MPT GU or GL CPRI MUX, one BBU can provide a maximum of six ports for converging data. The six ports must be provided by the same UBBP_U or UBBP_L.

l

In separate-MPT UL CPRI MUX, one BBU can provide a maximum of 24 ports for converging data. One converged board can correspond to one or two converging boards. A maximum of three pairs of one-to-one relationships or two pairs of one-to-two relationships are supported. The two-to-one relationship is not supported.

GU/GL CPRI MUX BBU3910s support separate-MPT GU or GL CPRI MUX when the following conditions are met: l

A UBBP_U or UBBP_L serves as the converging board and is installed in one of slots 0 to 3. A GTMUb or GTMUc serves as the converged board and is installed in slot 6.

l

Data from slot 6 is converged to one of slots 0 to 3, but not to two or more of slots 0 to 3.

Figure 6-4 shows GU CPRI MUX as an example.

Issue 01 (2017-03-10)


29




UL CPRI MUX BBU3910s support separate-MPT UL CPRI MUX when the following conditions are met: A UBBP_U or UBBP_L serves as the converging or converged board and is installed in one of slots 0 to 5. In a BBU3910, one converged board can correspond to one or two converging boards. A maximum of three pairs of one-to-one relationships or two pairs of one-to-two relationships are supported. Figure 6-5 shows an example of three pairs of one-to-one relationships with LTE as the converging party.

Issue 01 (2017-03-10)


30



Figure 6-5 Separate-MPT UL CPRI MUX with LTE as the converging party (three pairs of one-to-one relationships)

In the preceding figure, boards in slots 0 and 1 are converged and converging boards, respectively. These two boards form a group. Similarly, boards in slots 2 and 3 form a group, and boards in slots 4 and 5 form a group. Figure 6-6 shows an example of two pairs of one-to-two relationships with LTE as the converging party.

Issue 01 (2017-03-10)


31



Figure 6-6 Separate-MPT UL CPRI MUX with LTE as the converging party (two pairs of one-to-two relationships)

In the preceding figure, the board in slot 0 is a converged board, and boards in slots 4 and 5 are converging boards. These three boards form a group. Similarly, boards in slots 1, 2, and 3 form a group.

Issue 01 (2017-03-10)


32


7

7 Star Topology with CPRI MUX (BBU3910A)

Star Topology with CPRI MUX (BBU3910A)

l

A BBU3910A supports CPRI MUX only in co-MPT scenarios, including the GU/GL/UL/GUL CPRI MUX.

l

CPRI MUX can only be used within one BBU.

Figure 7-1 shows GU CPRI MUX as an example. Figure 7-1 GU CPRI MUX in co-MPT scenarios where a BBU3910A is used

Issue 01 (2017-03-10)


33


8

8 Chain Topology with CPRI MUX

Chain Topology with CPRI MUX

In a chain topology with CPRI MUX, configurations of a BBU, including the BBU3900, BBU3910, and BBU3910A, are the same as the configurations of the BBU in a star topology. On the RRU side, multimode RF modules working in the same or different modes can be cascaded on one CPRI link. Intra-mode cascading is recommended and inter-mode cascading is provided for use in specific scenarios. NOTE

In a chain topology with CPRI MUX, preferentially activate GSM cells served by the RF modules that can process GSM signals and are configured at the upper levels on a chain, that is close to a baseband processing board.

l

Intra-mode cascading: All cascaded multimode RF modules must be configured with the same mode and work in the same mode. Figure 8-1 shows GU CPRI MUX where UMTS serves as the converging party, the UBBP_U serves as the converging board, GSM baseband signals are processed by RF modules, and a BBU3900 is used.

l

Inter-mode cascading: Cascaded multimode RF modules can work in different modes. Inter-mode cascading is implemented in the following scenarios:

Issue 01 (2017-03-10)

–

Scenario 1: GSM is contained in the cascading chain in co-MPT CPRI MUX. The working modes of a multimode RF module in an inter-mode RF module cascading chain contain GSM. For example, the working mode may be GO, GU, GL, or GUL. In this scenario, all RF modules in the cascading chain must be multimode RF modules that support GSM. That is, all RF modules must support GU, GL, or GUL. Figure 8-2 shows co-MPT GU CPRI MUX where UMTS serves as the converging party, the UBBP_U serves as the converging board, GSM baseband signals are processed by RF modules, and a BBU3900 is used. The "UO Radio Unit" in this figure is working in UO, but it is a multimode RF module that supports GSM. That is, it supports GU or GUL.

–

Scenario 2: GSM is not contained in the cascading chain in co-MPT CPRI MUX. The working modes of all multimode RF modules in an inter-RAT RRU cascading chain do not contain GSM. These multimode RF modules work in UO, LO, or UL. In this scenario, cascaded multimode RF modules can be GU, GL, UL, or GUL RF modules. Figure 8-3 shows co-MPT UL CPRI MUX where UMTS serves as the converging party and a BBU3900 is used.

–

Scenario 3: In separate-MPT CPRI MUX, the multimode RF modules in the interRAT hybrid cascading chain can work in one or two modes, but all multimode RF modules must support both the converging and converged parties. For example, in Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

34



separate-MPT GU CPRI MUX, the multimode RF modules can work in GO, UO, or GU, but these modules must support GU or GUL, as shown in Figure 8-4. NOTE

For inter-mode cascading, GU or GO RF modules must be configured at the upper levels on a chain, that is close to a baseband processing board.

Figure 8-1 Co-MPT GU CPRI MUX using intra-mode cascading where a BBU3900 is used, UMTS serves as the converging party, the UBBP_U serves as the converging board, and GSM baseband signals are processed by RF modules

Figure 8-2 Co-MPT GU CPRI MUX using inter-mode cascading where a BBU3900 is used, UMTS serves as the converging party, the UBBP_U serves as the converging board, and GSM baseband signals are processed by RF modules

Issue 01 (2017-03-10)


35



Figure 8-3 Co-MPT UL CPRI MUX using inter-mode cascading where a BBU3900 is used and UMTS serves as the converging party

Figure 8-4 Separate-MPT GU CPRI MUX using inter-mode cascading where a BBU3900 is used and UMTS serves as the converging party

Issue 01 (2017-03-10)


36


9

9 CPRI MUX Trunk Chain Topology (RMU3900A)

CPRI MUX Trunk Chain Topology (RMU3900A)

9.1 Co-MPT Scenarios In co-MPT scenarios, the following conditions must be met if RMU3900As support CPRI MUX: l


l

Only the UBBPei board can serve as the converging board. It can be configured only in the BBU3910 and in slots 0 to 5.

l

One RMU3900A can be connected to only one UBBPei board.

l

RF modules must not directly connect to a UBBPei.

Figure 9-1 shows co-MPT UL CPRI MUX where LTE serves as the converging party and UMTS serves as the converged party. Figure 9-1 Co-MPT UL CPRI MUX where a UBBPei_L serves as the converging board

Issue 01 (2017-03-10)


37


9 CPRI MUX Trunk Chain Topology (RMU3900A)

NOTE

l The number of XCI ports (one or two) depends on the service bandwidth carried by RRUs connecting to the RMU. l When a UBBPei board is used as a UL dual-mode board, block and unblock the CPRI ports in case of insufficient bandwidth of CPRI links if the board supports inter-board interference cancellation.

9.2 Separate-MPT Scenarios In separate-MPT scenarios, the following conditions must be met if RMU3900As support CPRI MUX: l


l

One mode can only converge data or have its data converged. Data can only be converged to one board at a time.

l

Only the UBBPei board can serve as the converging board. It can be configured only in the BBU3910 and in slots 0 to 5.

l

In separate-MPT UL scenarios, the converged board must be a UBBPd or UBBPe.

l

Each BBU can provide a maximum of eight XCI ports.

Figure 9-2 shows separate-MPT UL CPRI MUX where LTE serves as the converging party. Figure 9-2 Separate-MPT UL CPRI MUX where LTE serves as the converging party

NOTE

When one XCI port cannot provide sufficient physical bandwidth required by all cells carried by the connected RRUs, two XCI ports can be used to connect the RMU3900A. The two XCI ports work in a load sharing mode. When one XCI port becomes faulty, the O&M links automatically switch over to the other XCI link. If the other XCI link has sufficient physical bandwidth, the service data can also be switched over to the other XCI link.

Issue 01 (2017-03-10)


38


10

10 CPRI MUX with Multimode Load Sharing Topology

CPRI MUX with Multimode Load Sharing Topology

In co-MPT scenarios, if two CPRI links on an RF module carry the data of two or more modes, this network topology is called the multimode load sharing topology. If each CPRI link in the multimode load sharing topology can transmit data of only one mode, the CPRI MUX feature is not required. l

For details about this network topology, see RRU/RFU/AAU Topologies > LoadSharing Topology > Multimode Load-Sharing Topology in RF Unit and Topology Management Feature Parameter Description.

l

If a CPRI link in the multimode load sharing topology needs to transmit data of multiple modes, the CPRI MUX feature is required. In this scenario, only GUL RF modules support CPRI MUX with multimode load sharing at present. Two CPRI links carry GU +L data, with one link carrying GU data and the other carrying LTE data, as shown in Figure 10-1.

NOTICE l In the multimode load sharing topology, two CPRI links of an RF module must be connected to two baseband processing boards or two interface boards of different modes. In other words, only a BBU3900 or a BBU3910 supports multimode load sharing topology. l In the multimode load sharing topology, the number of LTE cells cannot exceed the maximum number of LTE cells supported by one CPRI link, which depends on the CPRI port rate. For the number of LTE cells supported by different CPRI port rates, see "CPRI Specifications" in Technical Specifications of the eNodeB FDD > Technical Specifications of the BBU3900 and BBU3910 > Product Specifications in 3900 Series Base Station Technical Description. l If a UBBP is used in the multimode load sharing topology, the UBBP must have been configured with baseband resources of the mode served by this board. Otherwise, carriers cannot be successfully allocated to the CPRI ports on this UBBP. l In multimode load sharing, if a CPRI port is faulty or the board carrying this CPRI port is faulty, services of certain modes cannot be established. After the fault is cleared, services of all modes will recover.

Issue 01 (2017-03-10)


39


10 CPRI MUX with Multimode Load Sharing Topology

Figure 10-1 GU+L load sharing topology

Issue 01 (2017-03-10)


40


11

11 Triple-Mode Dual-Star Topology

Triple-Mode Dual-Star Topology

In a triple-mode dual-star topology, two modes use CPRI MUX and form a separate-MPT dual-star topology with the third mode. This topology applies only to a BBU3900 and a BBU3910. Note that the converging and converged parties in the CPRI MUX feature share one BBU

Issue 01 (2017-03-10)


41



11.1 GU+L Dual-Star Topology In Figure 11-1, BBU 0 uses separate-MPT GU CPRI MUX. The WBBPf/UBBP_U provides a CPRI link to connect to the multimode RF module. In BBU 1 (LTE mode), the LBBP/ UBBP_L provides a CPRI link to connect to the multimode RF module. In this way, the WBBPf/UBBP_U and LBBP/UBBP_L form a GU+L dual-star topology. Figure 11-1 GU+L dual-star topology

11.2 GL+U Dual-Star Topology In Figure 11-2, BBU 0 uses separate-MPT GL CPRI MUX. The LBBPd/UBBP_L provides a CPRI link to connect to the multimode RF module. In BBU 1 (UMTS mode), the WBBP/ UBBP_U provides a CPRI link to connect to the multimode RF module. In this way, the LBBPd/UBBP_L and WBBP/UBBP_U form a GL+U dual-star topology. Figure 11-2 GL+U dual-star topology

Issue 01 (2017-03-10)


42



11.3 G[U*L] Dual-Star Topology UMTS and LTE share one main control board, and the WBBPf/UBBP_U, LBBPd/UBBP_L, or UBBP_UL uses a UL port to connect to a multimode RF module. GSM uses an independent main control board GTMU, and the GTMU uses a CPRI port to connect to the multimode RF module. In this way, the WBBPf/UBBP_U, LBBPd/UBBP_L, or UBBP_UL and GTMU form a G[U*L] dual-star topology. Figure 11-3 shows the G[U*L] dual-star topology in which a WBBPf/UBBP_U provides UL CPRI ports. Figure 11-3 G[U*L] dual-star topology

Issue 01 (2017-03-10)


43


12

12 Specifications of the CPRI MUX Feature

Specifications of the CPRI MUX Feature

12.1 Converging Capabilities In separate-MPT or co-MPT CPRI MUX, the multimode converging capability depends on the CPRI line rate and the board capabilities of the converging party. Table 12-1 lists the converging capability of the converging party in multimode scenarios where CPRI MUX is used with a BBU3900 or a BBU3910. Table 12-2 lists the converging capability in multimode scenarios where CPRI MUX is used with a BBU3910A. Table 12-3 and Table 12-4 list the converging capability in multimode scenarios where CPRI MUX is used with an RMU. NOTE

l CPRI link rate, maximum number of carriers supported by a CPRI link, and maximum number of carriers supported by a board all refer to those of the converging party. l Converging capabilities in the tables apply to common cells. For the impact of different features on cell capacity, see the corresponding feature parameter description. l When GSM baseband signals are processed by the baseband processing board, the tables list the numbers of GSM TRXs supported when the antenna capability is 1T2R. l The tables list the numbers of supported UMTS cells when the antenna capability is 1T2R. l The tables list LTE-related capacity specifications when the antenna capability is 2T2R. l The capabilities of a BBU3910A or a BBU3900/BBU3910 converging board cannot exceed the maximum carrier/cell specifications of a site. For the maximum carrier/cell specifications of a site, see Product Specifications > Technical Specifications of the BBU3900/BBU3910 or Technical Specifications of the BBU3910A > Capacity Specifications in 3900 Series Base Station Technical Description.

Table 12-1 CPRI line rates and the converging capabilities of the converging party in multimode scenarios where CPRI MUX is used with a BBU3900 or a BBU3910

Issue 01 (2017-03-10)

CPRI Line Rate

2.5 Gbit/s

4.9 Gbit/s

9.8 Gbit/s

Converging Capabilities of a CPRI Link (GU)

16 GSM TRXs+

32 GSM TRXs(1)+

32 GSM TRXs(1)+

4 UMTS cells

8 UMTS cells

16 UMTS cells


44



CPRI Line Rate

2.5 Gbit/s

4.9 Gbit/s

9.8 Gbit/s

Converging Capabilities of a Board (GU)

96 GSM TRXs(2)+

126 GSM TRXs(2)+

126 GSM TRXs(2)(3)+

24 UMTS cells

24 UMTS cells

24 UMTS cells

Converging Capabilities of a CPRI Link (GL)

16 GSM TRXs+

32 GSM TRXs(1)+

32 GSM TRXs(1)+

LTE 1x10 MHz

LTE 1x20 MHz

LTE 2x20 MHz

Converging Capabilities of a Board (GL)

96 GSM TRXs(2)+

126 GSM TRXs(2)+

126 GSM TRXs(2)(3)+

LTE 6x10 MHz

LTE 6x20 MHz(4)

LTE 8x20 MHz(4)

Converging Capabilities of a CPRI Link (UL)

4 UMTS cells+

8 UMTS cells+

8 UMTS cells+

LTE 1x10 MHz

LTE 1x20 MHz

LTE 2x20 MHz or 3 UMTS cells+ LTE 3x20 MHz

Issue 01 (2017-03-10)

Converging Capabilities of a Board (UL)

24 UMTS cells+

24 UMTS cells+

LTE 6x10 MHz

LTE 6x20

Converging Capabilities of a CPRI Link (GUL)

6 GSM TRXs+

12 GSM TRXs+

24 GSM TRXs+

2 UMTS cells+

4 UMTS cells+

8 UMTS cells+

LTE 1x10 MHz

LTE 1x20 MHz

LTE 2x20 MHz(5)

Converging Capabilities of a Board (GUL)

36 GSM TRXs+

72 GSM TRXs+

126 GSM TRXs(2)+

12 UMTS cells+

24 UMTS cells+

24 UMTS cells+

LTE 6x10 MHz

LTE 6x20 MHz(4)

LTE 8x20 MHz(4)

MHz(4)


24 UMTS cells+ LTE 8x20 MHz(4)

45



NOTE

l

(1)

In separate-MPT GU or GL CPRI MUX where a BBU3910 is used, if the number of converging ports is less than or equal to five, a single CPRI link can carry 32 GSM TRXs; if the number of converging ports is six, a single CPRI link can only carry 24 GSM TRXs.

l When GSM baseband signals are processed by RF modules, the GSM capacity listed in the preceding table is the number of GSM carriers in the time division multiplexing (TDM) transmission mode when the maximum distance between the BBU and the RF module is 20 km. In the IP over E1 and IP over FE transmission schemes, use capacity specifications in Table 12-1 if these specifications do not exceed the maximum carrier specifications of a site; use the maximum capacity specifications of a site if capacity specifications in Table 12-1 exceed the maximum capacity specifications of a site. l

(2)

l

(3) In separate-MPT GU or GL CPRI MUX where a BBU3900 is used, when a WBBPf or an LBBPd serves as the converging board:

The specifications apply to scenarios where GSM baseband signals are processed by RF modules. When GSM baseband signals are processed by baseband processing boards, a maximum of 72 GSM TRXs can be supported by the boards.

If the CPRI line rate of ports on a converging board is 9.8 Gbit/s, the converging board can provide a maximum of three converging ports, which must be ports 0, 1, and 2. If the CPRI line rates of ports on a converging board include 9.8 Gbit/s and 4.9 Gbit/s simultaneously, the converging board can provide the following combination of converging ports: Three 9.8 Gbit/s ports and one 4.9 Gbit/s port Two 9.8 Gbit/s ports and two 4.9 Gbit/s ports One 9.8 Gbit/s port and four 4.9 Gbit/s ports A 9.8 Gbit/s converging port must be any one of ports 0, 1, and 2. l

(4)

l

(5)

When the baseband signals of an LTE cell are processed on the baseband processing board in slot 0, 1, 4, or 5 of a BBU3900, the board supports LTE 4x20 MHz 2T2R. Only the UBBP supports GUL CPRI MUX with a CPRI line rate of 9.8 Gbit/s.

NOTICE l The minimum CPRI line rate of the converging board is 2.5 Gbit/s.

Table 12-2 CPRI line rates and the converging capabilities of the converging party in multimode scenarios where CPRI MUX is used with a BBU3910A

Issue 01 (2017-03-10)

CPRI Line Rate

2.5 Gbit/s

4.9 Gbit/s

9.8 Gbit/s

Converging Capabilities of a CPRI Link (GU)

16 GSM TRXs+

32 GSM TRXs+

32 GSM TRXs+

4 UMTS cells

8 UMTS cells

12 UMTS cells

Converging Capabilities of a BBU (GU)

48 GSM TRXs+

48 GSM TRXs+

48 GSM TRXs+

12 UMTS cells

12 UMTS cells

12 UMTS cells

Converging Capabilities of a CPRI Link (GL)

16 GSM TRXs+

32 GSM TRXs+

32 GSM TRXs+

LTE 1x10 MHz

LTE 1x20 MHz

LTE 2x20 MHz

Converging Capabilities of a BBU (GL)

48 GSM TRXs+

48 GSM TRXs+

48 GSM TRXs+

LTE 6x10 MHz

LTE 6x20 MHz

LTE 6x20 MHz


46



CPRI Line Rate

2.5 Gbit/s

4.9 Gbit/s

9.8 Gbit/s


4 UMTS cells+

6 UMTS cells+

6 UMTS cells+

LTE 1x10 MHz

LTE 1x20 MHz


Converging Capabilities of a BBU (UL)

6 UMTS cells+

6 UMTS cells+

6 UMTS cells+

LTE 3x10 MHz

LTE 3x20 MHz

LTE 3x20 MHz

Converging Capabilities of a CPRI Link (GUL)

6 GSM TRXs+

12 GSM TRXs+

12 GSM TRXs+

2 UMTS cells+

4 UMTS cells+

6 UMTS cells+

LTE 1x10 MHz

LTE 1x20 MHz

LTE 2x20 MHz

36 GSM TRXs+

48 GSM TRXs+

48 GSM TRXs+

6 UMTS cells+

6 UMTS cells+

6 UMTS cells+

LTE 3x10 MHz

LTE 3x20 MHz

LTE 3x20 MHz

Converging Capabilities of a BBU (GUL)

NOTE

The table lists the numbers of GSM TRXs in the IP over E1 and IP over FE transmission schemes when the maximum distance between the BBU and the RF module is 20 km and the GSM baseband signals are processed by RF modules.

Table 12-3 CPRI line rates and the converging capabilities of the converging party in multimode scenarios where CPRI MUX is used with an RMU3900A CPRI Line Rate

2.5 Gbit/s

4.9 Gbit/s

9.8 Gbit/s


4 UMTS cells+

8 UMTS cells+

8 UMTS cells+

LTE 1x10 MHz

LTE 1x20 MHz


Table 12-4 CPRI line rates and the converging capabilities of the converging party in multimode scenarios where CPRI MUX is used on the XCI ports of a UBBPei board CPRI Line Rate

9.8 Gbit/s

10.1 Gbit/s


8 UMTS cells+

8 UMTS cells+

LTE 2x20 MHz

LTE 3x20 MHz

or 3 UMTS cells+ LTE 3x20 MHz Converging Capabilities of a BBU (UL)

Issue 01 (2017-03-10)

8 UMTS cells+

8 UMTS cells+

LTE 2x20 MHz

LTE 2x20 MHz


47



NOTE

l On the UBBPei board, the XCI port rate can be either 9.8 Gbit/s or 10.1 Gbit/s. l The minimum CPRI line rate of the converging board is 2.5 Gbit/s.

Capacity specifications for each mode with different configurations are calculated as follows: l

GSM: –

l

l

When GSM baseband signals are processed by RF modules, the numbers of GSM TRXs are reduced by half if the following condition is met: 20 km < distance between the BBU and the RF module ≤ 40 km.

UMTS: –

The number of cells supported when the antenna capability is 1T2R is the same as that supported when the antenna capability is 2T2R.

–

The antenna capability is inversely proportional to the number of cells. For example, the number of cells supported when the antenna capability is 1T2R is twice that supported when the antenna capability is 2T4R.

LTE: –

When LTE cells have the same antenna capability and CPRI line rate, the number of cells supported by a 3 MHz, 5 MHz, 10 MHz, or 20 MHz cell is inversely proportional to the bandwidth of LTE cells. For example, the number of cells supported by a 3 MHz cell is twice that supported by a 5 MHz cell, and the number of cells supported by a 5 MHz cell is twice that supported by a 10 MHz cell.

–

When LTE cells have the same antenna capability and CPRI line rate, 1.4- and 3MHz cells support the same number of cells, and 15- and 20-MHz cells support the same number of cells.

–

When LTE cells have the same bandwidth, the antenna capability is inversely proportional to the number of cells for 1T1R, 2T2R, and 4T4R. For example, when the cell bandwidth is 20 MHz, the number of cells supported when the antenna capability is 2T2R is twice that supported when the antenna capability is 4T4R.

–

When LTE cells have the same bandwidth, the number of cells supported by 1T2R and 2T2R antennas is the same, and that supported by 2T4R and 4T4R antennas is the same.

Examples of Application Scenarios Scenario 1: BBU3900 GL 1800 MHz GSM configuration requirements: S2/2/2 LTE configuration requirements: 3x20 MHz 2T2R The capacity requirement of each CPRI link is 2 GSM TRXs + LTE 1x20 MHz 2T2R. The capacity requirement of each board is 6 GSM TRXs + LTE 3x20 MHz 2T2R. According to Table 12-1, the CPRI line rate for a CPRI link that supports a 20 MHz 2T2R LTE cell is 4.9 Gbit/s. The corresponding carrier capacity of a GL converging board is 126 GSM TRXs + LTE 4x20 MHz 2T2R. Therefore, the capacity requirements can be met and this configuration is supported. Scenario 2: BBU3900 GL 1800 MHz GSM configuration requirements: S2/2/2 LTE configuration requirements: 3x10 MHz 4T4R The capacity requirement of each CPRI link is 2 GSM TRXs + LTE 1x10 MHz 4T4R. Issue 01 (2017-03-10)


48



The capacity requirement of each board is 6 GSM TRXs + LTE 3x10 MHz 4T4R. Therefore, a 10 MHz 4T4R LTE cell needs to be converted to 2T2R LTE cells based on the preceding calculation methods. The conversion is as follows: 1x10 MHz 4T4R -> 2x10 MHz 2T2R -> 1x20 MHz 2T2R. According to Table 12-1, the CPRI line rate for a CPRI link that supports a 20 MHz 2T2R cell is 4.9 Gbit/s. The corresponding carrier capacity of a GL converging board is 126 GSM TRXs + LTE 4x20 MHz 2T2R. Therefore, the capacity requirements can be met and this configuration is supported. Scenario 3: BBU3900 GL 1800 MHz GSM configuration requirements: S2/2/2/2/2/2 LTE configuration requirements: 6x20 MHz 2T2R The capacity requirement of each CPRI link is 2 GSM TRXs + LTE 1x20 MHz 2T2R. The capacity requirement of each board is 12 GSM TRXs + LTE 6x20 MHz 2T2R. According to Table 12-1, the CPRI line rate for a CPRI link that supports a 20 MHz 2T2R LTE cell is 4.9 Gbit/s. The corresponding carrier capacity of a GL converging board is 126 GSM TRXs + LTE 4x20 MHz 2T2R. Therefore, the capacity requirements of LTE 6x20 MHz 2T2R cannot be met and this configuration is not supported. In this case, contact Huawei engineers for technical support.

12.2 Cascading Level of the Chain Topology Using the CPRI MUX Feature Table 12-5 lists the maximum cascading level of the chain topology using the CPRI MUX feature. The maximum number of cascading levels is determined by the cell capacity of each mode and the carrier capabilities of the converging party. For details about the capabilities of the converging party, see section 12.1 Converging Capabilities. Table 12-5 Cascading Level of the Chain Topology Using the CPRI MUX Feature Mode

Maximum Cascading Level

GU

6

GL

4

UL

4

GUL

4

For the distance between the RF modules and the BBU, see Product Specifications > Technical Specifications of RRUs > Specifications of CPRI Ports in 3900 Series Base Station Technical Description. NOTE

If the CPRI MUX converging capability of a base station is exceeded, cell status of certain cells under the base station may be abnormal.

Issue 01 (2017-03-10)


49


13 Related Features

13

Related Features

13.1 Prerequisite Features None

13.2 Mutually Exclusive Features CPRI MUX is mutually exclusive with the following features: l

GBFD-113701 Frequency Hopping (RF hopping, baseband hopping)

l

GBFD-113703 Antenna Frequency Hopping

In separate-MPT scenarios, GU/GL CPRI MUX does not support baseband hopping, RF frequency hopping between two RF modules, or antenna frequency hopping between the RF modules: l

Between two RF modules connecting to a GTMUb/GTMUc and a UBRI/UBRIb/ UBBP_G, respectively

l

Between two RF modules connecting to a converging board and a UBRI/UBRIb/ UBBP_G, respectively

The GU separate-MPT scenario is used as an example.

Issue 01 (2017-03-10)


50


13 Related Features


In Figure 13-1, the UBRI/UBRIb/UBBP_G and the GTMUb/GTMUc directly connect to one RF module, respectively. The GTMUb/GTMUc also is the converged board and the WBBP/ UBBP_U is the converging board that connects to an RF module working in GU mode, implementing GU CPRI MUX. RF frequency hopping between RF modules connected to the WBBP/UBBP_U and the GTMUb/GTMUc is supported. RF frequency hopping between RF modules connected to the GTMUb/GTMUc and the UBRI/UBRIb/UBBP_G and between RF modules connected to the WBBP/UBBP_U and UBRI/ UBRIb/UBBP_G is not supported. NOTE

The UBBP_G is a UBBP working in GSM mode.

If a UBRIb in a BBU3900 is the converging board in co-MPT scenarios, CPRI MUX does not support baseband hopping, RF frequency hopping between two RF modules, or antenna frequency hopping between a GTMUb/GTMUc (working in the Evolution mode) and a UBRIb.

13.3 Impacted Features l

GBFD-510104 Multi-site Cell For hardware capability and cell capacity specifications when both CPRI MUX and Multi-site Cell are used, see Multi-site Cell Feature Parameter Description.

Issue 01 (2017-03-10)


51


14 Network Impact

14

Network Impact

14.1 System Capacity No impact.

14.2 Network Performance No impact.

14.3 Reliability CPRI MUX in Separate-MPT Scenarios CPRI MUX in separate-MPT scenarios has the following impacts on system reliability: l

Operations or exceptions on the converging party Circuit switched (CS) and packet switched (PS) services of the converged party will be interrupted when a CPRI port of the converging party becomes faulty or when any of the following operations is performed by the converging party: –

Software reset or power-off reset on the main control board or the converging board

–

Removing and then inserting the main control board or the converging board Blocking the converging board

–

Commissioning CPRI ports on the converging board

In general, this duration lasts less than 3 minutes and the longest duration does not exceed 3.5 minutes. l

Operations or exceptions on the converged party –

Performing software reset on the main control board The data rate of PS services of the converging party may be reduced for less than 3s and the longest duration of rate reduction does not exceed 10s.

–

Performing power-off reset, inserting and then removing the main control board CS and PS services on the converging party will be interrupted for less than 1 minute and the longest duration of service interruption does not exceed 3 minutes.

Issue 01 (2017-03-10)


52


14 Network Impact

CPRI MUX in Co-MPT Scenarios CPRI MUX in co-MPT scenarios has the following impacts on system reliability: l

CS and PS services of the converged party will be interrupted when a CPRI port of the converging party becomes faulty or when either of the following operations is performed by the converging party: –

Software reset or power-off reset on the converging board blocking

–

Removing and then inserting the converging board commissioning CPRI ports on the converging board

In general, the interruption lasts shorter than 3 minutes and the longest interruption lasts no longer than 3.5 minutes. l

If the WBBPf converges data and a UMTS application is deleted or reset, cells on the converged party will become unavailable for less than 5 minutes.

l

If the LBBPd converges data and an LTE application is deleted or reset, cells on the converged party will become unavailable for less than 5 minutes.

l

If the UBRIb converges data and a GSM application is deleted or reset, there is no impact on the converged party.

l

When a UBBP serves as the converging board, deleting or resetting the applications of the modes configured on this board does not affect the converged party.

l

Adding baseband resources to one mode configured on a UBBP interrupts services of other modes configured on this board, but does not affect services of the converged party that communicates with this board through the BBU backplane. NOTE

The service interruption duration does not include the duration of manual operations.

Issue 01 (2017-03-10)


53


15

15 Engineering Guidelines

Engineering Guidelines

For scenarios where CPRI MUX is used with the RMU solution, see section "Engineering Guidelines" in RMU Feature Parameter Description.

Issue 01 (2017-03-10)


54



15.1 When to Use You can enable the CPRI MUX feature in the following scenarios: l

Sites in which a single-mode base station is to be evolved into a multimode base station and the operator requires that the existing topology of fiber optic cables remain unchanged to reduce engineering costs

l

Sites in which a co-MPT dual-mode or multimode base station is to be deployed and the operator requires that costs of fiber optic cables be reduced

l

Sites whose coverage must be ensured through cascaded RF modules, such as stadiums, subways, and high-speed railways

15.2 Required Information The following information must be collected before feature deployment: l

Names of baseband processing boards that are to be used in CPRI MUX

l

Names of RF modules that are to be used in CPRI MUX

l

Information about optical modules

l

Planned site capacity

15.3 Network Planning RF Planning N/A

Network Planning Perform network planning by referring to instructions in 4 CPRI Topology Principles for a Multimode Base Station, 5 Star Topology with CPRI MUX (BBU3900), 6 Star Topology with CPRI MUX (BBU3910), 7 Star Topology with CPRI MUX (BBU3910A), 8 Chain Topology with CPRI MUX, 9 CPRI MUX Trunk Chain Topology (RMU3900A), 10 CPRI MUX with Multimode Load Sharing Topology, and 11 Triple-Mode Dual-Star Topology.

Hardware Planning When selecting BBU boards that are to be used in CPRI MUX, you must consider the application scenarios and constraints provided in 3 BBUs and Boards That Support CPRI MUX, 5 Star Topology with CPRI MUX (BBU3900), 6 Star Topology with CPRI MUX (BBU3910), 7 Star Topology with CPRI MUX (BBU3910A), 8 Chain Topology with CPRI MUX, 9 CPRI MUX Trunk Chain Topology (RMU3900A), 10 CPRI MUX with Multimode Load Sharing Topology, and 11 Triple-Mode Dual-Star Topology.

Issue 01 (2017-03-10)


55



NOTICE The CPRI link rates of baseband processing boards/interface boards, optical modules, and RF modules must match each other and must meet the specifications in 12.1 Converging Capabilities.

15.4 Deployment 15.4.1 Requirements Hardware RF modules have been installed. Cables between RF modules and BBUs have been connected as required by the CPRI MUX feature. For detailed installation procedures, see the corresponding Base station Installation Guide and Site Maintenance Guide of the base stations. NOTE

If CPRI MUX is to be deployed in a site where a single-mode base station is to be evolved into a multimode base station, the hardware must meet the requirements of CPRI MUX. If it does not, replace the hardware.

License None

15.4.2 Data Preparation CPRI MUX in Separate-MPT Scenarios Multimode RF modules that work in multiple modes must follow the following configuration rules: l

RF modules are configured and monitored by each mode.

l

RF modules working in the same mode must have the same configuration. Otherwise, the ALM-26274 Inter-System Board Object Configuration Conflict alarm will be reported.

l

Table 15-1 lists parameters that must have the same configuration when CPRI MUX is deployed in separate-MPT scenarios.

Issue 01 (2017-03-10)


56



Table 15-1 Common parameters Parameter Name on GSM (GBTS) Side

Parameter ID on GSM (GBTS) Side

Parameter Name on GSM (eGBTS)/ UMTS/LTE Side

Parameter ID on GSM (eGBTS)/ UMTS/LTE Side

Topo Type

TT(BSC6910,BSC6900 )

Topo Type

TT

Cabinet No.

CN(BSC6910,BSC6900 )

Cabinet No.

CN

Subrack No.

SRN(BSC6910,BSC69 00)

Subrack No.

SRN

Slot No.

SN(BSC6910,BSC6900 )

Slot No.

SN

Board Type

BT(BSC6910,BSC6900 )

RRU Type

RT

Working Mode

WORKINGSTANDAR D(BSC6900,BSC6910)

RRU Work Standard

RS

The RRU configuration of the converged party takes effect only after RRUs of the converging party have been configured. Data configurations on the converging party remain unchanged compared with those for the trunk chain, chain, or star topology. For detailed data configurations, see RF Unit and Topology Management Feature Parameter Description > Engineering Guidelines > Deployment > Data Preparation. Enable the CPRI MUX feature only on the converged party: l

If GSM (GBTS) is the converged party, configure the BTSRXUCHAIN MO. For key parameters, see Table 15-2.

l

If GSM (eGBTS)/UMTS/LTE is the converged party, configure the RRUCHAIN MO. For key parameters, see Table 15-2. Table 15-2 Key parameters in the BTSRXUCHAIN/RRUCHAIN MO

Issue 01 (2017-03-10)

Parameter Name

Parameter ID

Remarks (Configuration Principle for Different Scenarios)

Data Source

Access Type

AT(BSC6910,BSC 6900,eGBTS)

Set this parameter to PEERPORT.

Engineering Design

Head Cabinet No.

HCN(BSC6910,BS C6900,eGBTS)

Set these parameters to the cabinet number, subrack number, slot number, and optical port number of the

Engineering Design


57



Parameter Name

Parameter ID

Remarks (Configuration Principle for Different Scenarios)

Data Source

Head Subrack No.

HSRN(BSC6910,B SC6900,eGBTS)

Engineering Design

Head Slot No.

HSN(BSC6910,BS C6900,eGBTS)

CPRI port on the baseband board of the peer end, respectively.

Head Port No.

HPN(BSC6910,BS C6900,eGBTS)

Local Slot No.

LSN

Engineering Design Engineering Design

l BBU3900: This parameter is set to 255 by default and the slot number does not need to be configured for the converged party. If GSM (GBTS) is the converged party, this parameter cannot be configured.

Equipment Planning

l BBU3910: – In separate-MPT GU/GL CPRI MUX (GBTS on the GSM side), set this parameter to 255, and do not set the slot No. for the converged party. – In separate-MPT GU/GL CPRI MUX (eGBTS on the GSM side) or UL CPRI MUX, set the slot No. for the converged party based on the actual slot where the converged board is configured.

CPRI MUX in Co-MPT Scenarios In co-MPT scenarios, if the networking meets the requirements described in 9.1 Co-MPT Scenarios/5.1 Co-MPT Scenarios/6.1 Co-MPT Scenarios, CPRI MUX is supported by default. l

Issue 01 (2017-03-10)

Data configurations for the CPRI MUX-based trunk chain, chain, or star topology in a co-MPT base station are the same as those in a single-mode base station. For detailed data configurations for the trunk chain, chain, and star topologies, see RF Unit and Topology Management Feature Parameter Description > Engineering Guidelines > Deployment > Data Preparation. Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

58



l

Data configurations for the CPRI MUX-based load-sharing topology in a co-MPT base station are the same data as those in an eNodeB. For detailed data configurations for the load-sharing topology, see RF Unit and Topology Management Feature Parameter Description > Engineering Guidelines (eNodeB) > Deployment > Data Preparation.

l

For how to configure UBBP baseband resources, see sections "Baseband equipment" and "Baseband resources" in 3900 Series Base Station Initial Configuration Guide > 3900 Series Base Station Initial Configuration (CME-based) > Creating Base Stations > Creating Co-MPT Base Station > Creating Co-MPT Base Stations in Batches > Preparing Co-MPT Base Station Data > Radio Data for a Co-MPT Base Station.

GU+L or GL+U Triple-Mode Dual-Star Topology For details about this network topology, see 11.1 GU+L Dual-Star Topology and 11.2 GL+U Dual-Star Topology. For details about data preparation, see CPRI MUX in Separate-MPT Scenarios and data preparation in the dual-star networking scenario in RF Unit and Topology Management > Engineering Guidelines (Multimode Base Station) > Deployment > Data Preparation.

G[U*L] Dual-Star Topology For details about this network topology, see 11.3 G[U*L] Dual-Star Topology. For details about data preparation, see CPRI MUX in Co-MPT Scenarios and data preparation in the dual-star networking scenario in RF Unit and Topology Management > Engineering Guidelines (Multimode Base Station) > Deployment > Data Preparation.

15.4.3 Activation In co-MPT scenarios, CPRI MUX is supported by default when the requirements described in 5.1 Co-MPT Scenarios/6.1 Co-MPT Scenarios/7 Star Topology with CPRI MUX (BBU3910A)/9.1 Co-MPT Scenarios are met. Software configuration is not required for activating CPRI MUX. For data configurations for a co-MPT base station, see 3900 Series Base Station Initial Configuration Guide. This section describes the procedure for activating CPRI MUX in separate-MPT scenarios.

Using MML Commands Step 1 On the converging party side, run the MML command ADD RRUCHAIN to add an RRU/RFU chain. Step 2 On the converging party side, run the MML command ADD RRU to add an RRU/RFU to the RRU/RFU chain. On the converged party, run the MML command to add an RRU/RFU chain: Run ADD RRUCHAIN for GSM (eGBTS)/UMTS/LTE, and run ADD BTSRXUCHAIN for GSM (GBTS). For key parameter settings, see Table 15-2. Step 3 On the converged party, run the MML command to add an RRU/RFU to the RRU/RFU chain. Run ADD RRU for GSM (eGBTS)/UMTS/LTE, and run ADD BTSRXUBRD for GSM (GBTS). ----End Issue 01 (2017-03-10)


59



NOTE

Data configurations must be the same for RRUs on the converging party and converged party. For detailed parameter settings, see Table 15-1.

MML Command Examples BBU3900: //Adding an RRU chain on the converging party side ADD RRUCHAIN: RCN=0, TT=CHAIN, AT=LOCALPORT, HCN=0, HSRN=0, HSN=3, HPN=0;

//Adding an RRU to the RRU chain on the converging party side ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=UL, RXNUM=2, TXNUM=2;

//Adding an RRU chain on the converged party side ADD RRUCHAIN: RCN=0, TT=CHAIN, AT=PEERPORT, HCN=0, HSRN=0, HSN=3, HPN=0;

//Adding an RRU to the RRU chain on the converged party side ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=UL, RXNUM=2, TXNUM=2;

BBU3910: //Adding an RRU chain on the converging party side ADD RRUCHAIN: RCN=0, TT=CHAIN, AT=LOCALPORT, HCN=0, HSRN=0, HSN=3, HPN=0;

//Adding an RRU to the RRU chain on the converging party side ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=UL, RXNUM=2, TXNUM=2;

//Adding an RRU chain on the converged party side ADD RRUCHAIN: RCN=0, TT=CHAIN, AT=PEERPORT, HCN=0, HSRN=0, HSN=3, HPN=0, LSN=2;

//Adding an RRU to the RRU chain on the converged party side ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=UL, RXNUM=2, TXNUM=2;

Using the CME to Perform Single Configuration Set parameters on the CME according to the operation sequence in Table 15-3. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Table 15-3 Configuring parameters on the CME

Issue 01 (2017-03-10)

SN

MO

Parameter Name

Parameter ID

Notes

1

RRUCHAIN

Chain No.

RCN

Topo Type

TT

Access Type

AT

Add an RRU/RFU chain on the converging party side.


60


SN

2

3

MO

RRU

RRUCHAIN

BTSRXUCH AIN

Issue 01 (2017-03-10)


Parameter Name

Parameter ID

Head Cabinet No.

HCN

Head Subrack No.

HSRN

Head Slot No.

HSN

Head Port No.

HPN

Cabinet No.

CN

Subrack No.

SRN

Slot No.

SN

RRU Chain No.

RCN

RRU Type

RT

RF Unit Working Mode

RS

Chain No.

RCN

Topo Type

TT

Access Type

AT

Head Cabinet No.

HCN

Head Subrack No.

HSRN

Head Slot No.

HSN

Head Port No.

HPN

Local Slot No.

LSN

Chain No.

RCN(BSC6910,B SC6900)

Topo Type

TT(BSC6910,BS C6900)

Access Type

AT(BSC6910,BS C6900)

Head Cabinet No.

HCN(BSC6910, BSC6900)

Head Subrack No.

HSRN(BSC6910, BSC6900)

Head Slot No.

HSN(BSC6910,B SC6900)

Head Port No.

HPN(BSC6910, BSC6900)


Notes

Add an RRU/RFU to the RRU/RFU chain on the converging party side.

Add an RRU/RFU chain on the converged party side for GSM (eGBTS)/ UMTS/LTE.

Add an RRU/RFU chain on the converged party side for GSM (GBTS).

61



SN

MO

Parameter Name

Parameter ID

Notes

4

RRU

Cabinet No.

CN

Subrack No.

SRN

Slot No.

SN

RRU Chain No.

RCN

RRU Type

RT

Add an RRU/RFU to the RRU/RFU chain on the converged party side for GSM (eGBTS)/ UMTS/LTE.

RF Unit Working Mode

RS

Board Type

BT(BSC6910,BS C6900)

Cabinet No.

CN(BSC6910,BS C6900)

Subrack No.

SRN(BSC6910,B SC6900)

Slot No.

SN(BSC6910,BS C6900)

RXU Chain No.

RXUCHAINNO( BSC6910,BSC69 00)

Working Mode

WORKINGSTA NDARD(BSC69 10,BSC6900)

BTSRXUBR D

BTSRXUBP

Add an RRU/RFU to the RRU/RFU chain on the converged party side for GSM (GBTS).

NOTE

Data configurations must be the same for RRUs on the converging party and converged party. For detailed parameter settings, see Table 15-1.

Using the CME to Perform Batch Modification This feature does not support batch modification using the CME.

15.4.4 Activation Observation After the configured data is activated, check whether RF module-related alarms are reported on the Alarm/Event tab page of the LMT or U2000 for GSM, UMTS, or LTE. For details about RF module-related alarms, see section 15.7.1 Related Alarms. 1.

Check whether the status of RF modules is normal. –

Separate-MPT Scenarios On the BSC LMT or the U2000, run the DSP BTSBRD command to check whether RF modules on the GSM (GBTS) side function properly.

Issue 01 (2017-03-10)


62



On the LMT or the U2000 for the 3900 series base station, run the DSP BRD command to check whether RF modules on the GSM (eGBTS) side function properly. On the LMT or the U2000 for the 3900 series base station, run the DSP BRD command to check whether RF modules on the UMTS side function properly. On the LMT or the U2000 for the 3900 series base station, run the DSP BRD command to check whether RF modules on the LTE side function properly. –

Co-MPT Scenarios On the LMT or U2000 of converging party of a 3900 series base station, run the MML command DSP BRD to check whether RF modules on the LTE side function properly.

2.

Check whether the line rate of the converging port is the same as planned. –

Separate-MPT scenarios: On the LMT or U2000 for the 3900 series base station, run the MML command DSP CPRIPORT on the converging party side, and check whether the line rate of the converging port is the same as planned.

–

Co-MPT scenarios: Run the MML command DSP CPRIPORT to check whether the line rate of the converging port is the same as planned.

15.4.5 Deactivation This feature does not need to be deactivated.

15.4.6 Reconfiguration You can add an RRU to or remove an RRU from a cascaded RRU chain in the star or chain CPRI MUX topology. For how to add or remove RF modules to or from a chain or ring on the CME, see eRAN (FDD) Reconfiguration Guide > Device Data Reconfiguration > Adding or Deleting an RF Module in a Chain.

Separate-MPT Scenarios l

Adding an RRU to a cascaded RRU chain To add an RRU to a cascaded RRU chain without changing the original topology, you need to add the RRU information on both the converging and converged parties.

l

a.

Run the MOD RRUCHAIN command on the converging party to set a breaking point.

b.

Run MML commands on both the converging and converged parties to add an RRU. Run ADD RRU for GSM (eGBTS)/UMTS/LTE, and run ADD BTSRXUBRD for GSM (GBTS).

c.

Adjust the original cable connections and add an RRU to the specified position.

d.

Run the MOD RRUCHAIN command on the converged party to remove the breaking point.

Deleting an RRU from a cascaded RRU chain To remove an RRU from a cascaded RRU chain without changing the original topology, you need to remove the RRU information from both the converging and converged parties.

Issue 01 (2017-03-10)


63



a.

Run the MOD RRUCHAIN command on the converging party to set a breaking point.

b.

Run MML commands on both the converging and converged parties to remove an RRU. Run RMV RRU for GSM (eGBTS)/UMTS/LTE, and run RMV BTSRXUBRD for GSM (GBTS).

c.

Adjust the original cable connections and remove an RRU from the specified position.

d.

Run the MOD RRUCHAIN command on the converged party to remove the breaking point.

Co-MPT Scenarios l

Adding an RRU to a cascaded RRU chain To add an RRU to a cascaded RRU chain without changing the original topology:

l

a.

Run the MOD RRUCHAIN command to set a breaking point.

b.

Run the ADD RRU command to add an RRU.

c.

Adjust the original cable connections and add an RRU to the specified position.

d.

Run the MOD RRUCHAIN command to remove the breaking point.

Deleting an RRU from a cascaded RRU chain To remove an RRU from a cascaded RRU chain without changing the original topology: a.

Run the MOD RRUCHAIN command to set a breaking point.

b.

Run the RMV RRU command to remove an RRU.

c.

Adjust the original cable connections and remove an RRU from the specified position.

d.

Run the MOD RRUCHAIN command to remove the breaking point.

15.5 Performance Monitoring N/A

15.6 Parameter Optimization N/A

15.7 Possible Issues 15.7.1 Related Alarms Table 15-4 lists alarms related to the CPRI MUX feature. For detailed troubleshooting operations, see 3900 Series Multimode Base Station Alarm Reference, BSC6900 GSM Alarm Reference, and BSC6910 GSM Alarm Reference.

Issue 01 (2017-03-10)


64



Table 15-4 CPRI MUX-related alarms

Issue 01 (2017-03-10)

Alarm ID

Alarm Name

Description

ALM-26215

Inter-Board Service Link Failure

This alarm is reported if inter-board communication fails in the BBU. Services of the converged party are affected.

ALM-26235

RF Unit Maintenance Link Failure

This alarm is reported if the maintenance link between the BBU and the RF unit malfunctions. The alarm is triggered by any of the following faults and is reported by the converged party in separate-MPT scenarios: Optical modules on the baseband board of the converging party become faulty. Links used to forward data from the converged party to the converging party through the BBU backplane become faulty or resources are insufficient. The baseband board of the converging party is not installed, powered on, configured or the baseband board experiences hardware failures. The hardware capability of the baseband boards of the two parties is insufficient to support data converging through the BBU backplane. Aggregation relationships are incorrectly configured.

ALM-26270

Inter-System Communication Failure

In multi-mode configuration, this alarm is reported if the main control board in the current mode cannot communicate with the main control board in the other mode. If the two main control boards cannot communicate with each other for about 45s, this alarm is reported. If the two main control boards can communicate with each other for about 30s consecutively, this alarm is cleared.

ALM-26272

Inter-System RF Unit Parameter Settings Conflict

In multi-mode configuration, this alarm is reported if the parameter settings of an RF unit in a mode are inconsistent with those of the same RF unit in the other mode, such as the working mode or other RF parameters.


65


Issue 01 (2017-03-10)


Alarm ID

Alarm Name

Description

ALM-26274

Inter-System Board Object Configuration Conflict

In multi-mode configuration, this alarm is reported if the cabinet/ subrack/slot configuration of a board is inconsistent in different modes, the cabinet/subrack/slot configuration of different boards is the same in different modes, or a board that supports only one mode is used by multiple modes at the same time.

ALM-26277

Inter-System Control Rights Conflict

In multi-mode configuration, this alarm is reported if the loading control rights are not configured or are inconsistent between different modes in the base station.

ALM-26278

RF Unit Working Mode and Board Capability Mismatch

In multi-mode configuration, this alarm is reported if the configured working mode of an RF unit does not match the actual capability of the RF unit.

ALM-28016

GSM Local Cell Unusable

ALM-28017

GSM Local Cell Capability Decline

ALM-28006

Radio Signaling Link Disconnected

ALM-21801

GSM Cell out of Service

In a CPRI MUX-based topology with the GSM mode, multiple modes use one CPRI link to transmit data. As a result, bandwidth on the GSM side may be insufficient and this alarm is reported. This alarm is also reported when an RF module on a hybrid cascaded CPRI link does not support the GSM mode.

ALM-28203

Local Cell Unusable

ALM-28206

Local Cell Capability Decline

ALM-29240

Cell Unavailable

ALM-29243

Cell Capability Degraded

ALM-26262

Clock source exception alarms

When CPRI MUX is implemented, multiple modes use one CPRI link to transmit data. As a result, bandwidth on the UMTS side may be insufficient and this alarm is reported. When CPRI MUX is implemented, multiple modes use one CPRI link to transmit data. As a result, bandwidth on the LTE side may be insufficient and this alarm is reported. In a CPRI MUX scenario with clock mutual lock, if the major standard becomes abnormal, this alarm is reported by other standards.


66



15.7.2 MML Commands for Maintenance In separate-MPT scenarios, the converging and converged parties have their own O&M platforms. In co-MPT scenarios, the converging and converged parties share the same O&M platform. NOTE

After CPRI MUX is implemented, alarms will be reported if any exceptions occur. Clear the alarms according to the alarm reference.

Table 15-5 MML commands for maintenance MML Command

Application Scenario

Support by the Converging Party

Support by the Converged Party (Only in SeparateMPT Scenarios)

DSP RRUCHAIN

Use this command to query the number of RRUs carried on an RRU chain or ring over an optical port on the converging party and the number of cascading levels.

Fully supported

Fully supported

DSP RRUCHAINPHYT OPO

Use this command to query information about the RRUs connected to the CPRI port.

Fully supported

Fully supported

DSP CPRIPORT

Use this command to query real-time data rates and other information about the optical port on the panel of the converging party.

Fully supported

Partially supported: Use this command to query data rates on the CPRI port and the status of the aggregation port.

Use this command to query whether the optical port is in the aggregation state.

Issue 01 (2017-03-10)


67


MML Command

Application Scenario

Support by the Converging Party

Support by the Converged Party (Only in SeparateMPT Scenarios)

DSP CPRILBR

Use this command to query the current CPRI line rate of the specified chain or ring, the maximum CPRI line rate of the baseband processing board, the maximum CPRI line rate of each RRU or RFU on a chain or ring.

Fully supported

Partially supported: Use this command to query the current CPRI line rate of the specified chain/ring and the maximum CPRI line rate of each RRU or RFU on a chain or ring.

STR CPRILBRNEG

Use this command to start negotiation of the line rate on the optical port on the panel. Run this command if the RRU chain cannot be set up or the chain cannot operate at the maximum line rate due to changes in parameter settings of the RRU chain. Executing this command causes link disconnection, interrupting services.

Supported

Not supported

MOD RRUCHAIN

Use this command to set breakpoints on an RRU chain.

Supported

Not supported

L: DSP CELL

Use this command to query the cell status. Cell setup fails and cell capability degrades when CPRI bandwidth is insufficient.

Supported

Supported

U: DSP ULOCELL G(GBTS): DSP GTRXSTAT G(eGBTS): DSP GTRX

Issue 01 (2017-03-10)



68


16 Parameters

16

Parameters

Table 16-1 Parameters Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TT

BSC691 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

Meaning: RXU topology type, that is, RXU ring topology or RXU chain topology. In the case of the ring topology, the optical ports of the head and tail boards must be specified. In the case of the chain topology, only the optical port of the head board must be specified.

MOD BTSRX UCHAI N

GUI Value Range: CHAIN(Chain), RING(Ring) Unit: None Actual Value Range: CHAIN, RING Default Value: None

TT

BSC690 0

ADD BTSRX UCHAI N MOD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

Meaning: RXU topology type, that is, RXU ring topology or RXU chain topology. In the case of the ring topology, the optical ports of the head and tail boards must be specified. In the case of the chain topology, only the optical port of the head board must be specified. GUI Value Range: CHAIN(Chain), RING(Ring) Unit: None Actual Value Range: CHAIN, RING Default Value: None

Issue 01 (2017-03-10)


69


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

TT

BTS390 0, BTS390 0 WCDM A, BTS390 0 LTE

ADD RRUC HAIN

None

None

Meaning: Indicates the type of the topology. In a ring topology, the service data is transmitted on the fiber optic cable that carries the HDLC link. In a load sharing topology, the service data is transmitted on two fiber optic cables simultaneously, which enhances the transmission capability. The physical connection in the ring topology is similar to that in the load sharing topology. The trunk chain enables multiple CPRI fiber optic cables to simultaneously transmit service data.

MOD RRUC HAIN DSP RRUC HAINP HYTOP O

GUI Value Range: CHAIN(CHAIN), RING(RING), LOADBALANCE(LOADBALANCE), TRUNK_CHAIN(TRUNK_CHAIN)

LST RRUC HAIN

Unit: None Actual Value Range: CHAIN, RING, LOADBALANCE, TRUNK_CHAIN Default Value: None

CN

BSC691 0

ADD BTSRX UBRD

GBFD-1 11202

O&M of BTS

Meaning: Number of the cabinet where the BTS board is located. GUI Value Range: 0~62

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None

Actual Value Range: 0~62

MOD BTSRX UBRD QUICK MOD BTSRX UBRDT YPE RMV BTSRX UBRD

Issue 01 (2017-03-10)


70


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CN

BSC690 0

ADD BTSRX UBRD

GBFD-1 11202

O&M of BTS

Meaning: Number of the cabinet where the BTS board is located. GUI Value Range: 0~62

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None


MOD BTSRX UBRD QUICK MOD BTSRX UBRDT YPE RMV BTSRX UBRD CN


Issue 01 (2017-03-10)

DSP RRUCL KSRC

None

None

Meaning: Indicates the number of the cabinet where the RRU is located. GUI Value Range: 0~15

SET RRUCL KSRC

Unit: None

TST LOPRR U

Default Value: 0



71


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

SRN

BSC691 0

ADD BTSRX UBRD

GBFD-1 11202

O&M of BTS

Meaning: Number of the subrack where the BTS board is located. GUI Value Range: 0~254

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None


MOD BTSRX UBRD QUICK MOD BTSRX UBRDT YPE RMV BTSRX UBRD SRN

BSC690 0

ADD BTSRX UBRD

GBFD-1 11202

O&M of BTS

Meaning: Number of the subrack where the BTS board is located. GUI Value Range: 0~254

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None



Issue 01 (2017-03-10)


72


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

SRN


DSP RRUCL KSRC

None

None

Meaning: Indicates the number of the subrack where the RRU is located.

BSC691 0

ADD BTSRX UBRD

SN

GUI Value Range: 60~254

SET RRUCL KSRC

Unit: None

TST LOPRR U

Default Value: None


GBFD-1 11202

O&M of BTS

Meaning: Number of the slot where the BTS board is located. GUI Value Range: 0~23

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None



Issue 01 (2017-03-10)


73


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

SN

BSC690 0

ADD BTSRX UBRD

GBFD-1 11202

O&M of BTS

Meaning: Number of the slot where the BTS board is located. GUI Value Range: 0~23

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None


MOD BTSRX UBRD QUICK MOD BTSRX UBRDT YPE RMV BTSRX UBRD SN

BT


DSP RRUCL KSRC

BSC691 0

ADD BTSRX UBRD

None

Meaning: Indicates the number of the slot where the RRU is located. GUI Value Range: 0~3

SET RRUCL KSRC

Unit: None

TST LOPRR U

Default Value: 0

MOD BTSRX UBRD QUICK MOD BTSRX UBRDT YPE

Issue 01 (2017-03-10)

None


GBFD-1 11202

O&M of BTS

Meaning: Type of the newly added RXU board GUI Value Range: DRRU(DRRU), DRFU(DRFU), MRRU(MRRU), XRRU(XRRU), MRFU(MRFU), GRFU(GRFU), GRRU(GRRU), XRFU(XRFU), BTS3900E(BTS3900E), AIRU(AIRU) Unit: None Actual Value Range: DRRU, DRFU, MRRU, XRRU, MRFU, GRFU, GRRU, XRFU, BTS3900E, AIRU Default Value: None


74


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

BT

BSC690 0

ADD BTSRX UBRD

GBFD-1 11202

O&M of BTS

Meaning: Type of the newly added RXU board

MOD BTSRX UBRD QUICK

Unit: None Actual Value Range: DRRU, DRFU, MRRU, XRRU, MRFU, GRFU, GRRU, XRFU, BTS3900E, AIRU

MOD BTSRX UBRDT YPE RT


MOD RRU LST RRU

GUI Value Range: DRRU(DRRU), DRFU(DRFU), MRRU(MRRU), XRRU(XRRU), MRFU(MRFU), GRFU(GRFU), GRRU(GRRU), XRFU(XRFU), BTS3900E(BTS3900E), AIRU(AIRU)

Default Value: None

None

None

Meaning: Indicates the type of the RRU. GUI Value Range: MRRU(MRRU), MRXU(MRXU), PRRU(PRRU), MPRU(MPRU), MPMU(MPMU), MPRF(MPRF), AIRU(AIRU), MRIU(MRIU), GRRU(GRRU), LRRU(LRRU), ORRU(ORRU) Unit: None Actual Value Range: MRRU, MRXU, PRRU, MPRU, MPMU, MPRF, AIRU, MRIU, GRRU, LRRU, ORRU Default Value: None

Issue 01 (2017-03-10)


75


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

WORK INGST ANDA RD

BSC690 0

SET BTSRX UBP

GBFD-1 11202

O&M of BTS

Meaning: Working mode of the RXU board. GUI Value Range: GSM_AND_UMTS(GSM AND UMTS), UMTS(UMTS), GSM(GSM), GSM_AND_LTE(GSM AND LTE), LTE(LTE), UMTS_AND_LTE(UMTS AND LTE), GSM_AND_UMTS_AND_LTE(GSM, UMTS AND LTE), LTE_TDD(LTE TDD), GSM_AND_LTE_TDD(GSM AND LTE TDD), UMTS_AND_LTE_TDD(UMTS AND LTE TDD), LTE_AND_LTE_TDD(LTE AND LTE TDD), GSM_AND_UMTS_AND_LTE_TDD(GSM, UMTS AND LTE TDD), GSM_AND_LTE_AND_LTE_TDD(GSM, LTE AND LTE TDD), UMTS_AND_LTE_AND_LTE_TDD(UMTS, LTE AND LTE TDD), GSM_AND_UMTS_AND_LTE_AND_LTE_TDD(G SM, UMTS, LTE AND LTE TDD), NBIOT(NB-IoT), GSM_AND_NBIOT(GSM AND NB-IoT), UMTS_AND_NBIOT(UMTS AND NB-IoT), LTE_AND_NBIOT(LTE AND NB-IoT), GSM_AND_UMTS_AND_NBIOT(GSM, UMTS AND NB-IoT), GSM_AND_LTE_AND_NBIOT(GSM, LTE AND NB-IoT), UMTS_AND_LTE_AND_NBIOT(UMTS, LTE AND NB-IoT), GSM_AND_UMTS_AND_LTE_AND_NBIOT(GSM , UMTS, LTE AND NB-IoT) Unit: None Actual Value Range: GSM_AND_UMTS, UMTS, GSM, GSM_AND_LTE, LTE, UMTS_AND_LTE, GSM_AND_UMTS_AND_LTE, LTE_TDD, GSM_AND_LTE_TDD, UMTS_AND_LTE_TDD, LTE_AND_LTE_TDD, GSM_AND_UMTS_AND_LTE_TDD, GSM_AND_LTE_AND_LTE_TDD, UMTS_AND_LTE_AND_LTE_TDD, GSM_AND_UMTS_AND_LTE_AND_LTE_TDD, NBIOT, GSM_AND_NBIOT, UMTS_AND_NBIOT, LTE_AND_NBIOT, GSM_AND_UMTS_AND_NBIOT, GSM_AND_LTE_AND_NBIOT, UMTS_AND_LTE_AND_NBIOT, GSM_AND_UMTS_AND_LTE_AND_NBIOT Default Value: GSM(GSM)

Issue 01 (2017-03-10)


76


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

WORK INGST ANDA RD

BSC691 0

SET BTSRX UBP

GBFD-1 11202

O&M of BTS

Meaning: Working mode of the RXU board. GUI Value Range: GSM_AND_UMTS(GSM AND UMTS), UMTS(UMTS), GSM(GSM), GSM_AND_LTE(GSM AND LTE), LTE(LTE), UMTS_AND_LTE(UMTS AND LTE), GSM_AND_UMTS_AND_LTE(GSM, UMTS AND LTE), LTE_TDD(LTE TDD), GSM_AND_LTE_TDD(GSM AND LTE TDD), UMTS_AND_LTE_TDD(UMTS AND LTE TDD), LTE_AND_LTE_TDD(LTE AND LTE TDD), GSM_AND_UMTS_AND_LTE_TDD(GSM, UMTS AND LTE TDD), GSM_AND_LTE_AND_LTE_TDD(GSM, LTE AND LTE TDD), UMTS_AND_LTE_AND_LTE_TDD(UMTS, LTE AND LTE TDD), GSM_AND_UMTS_AND_LTE_AND_LTE_TDD(G SM, UMTS, LTE AND LTE TDD), NBIOT(NB-IoT), GSM_AND_NBIOT(GSM AND NB-IoT), UMTS_AND_NBIOT(UMTS AND NB-IoT), LTE_AND_NBIOT(LTE AND NB-IoT), GSM_AND_UMTS_AND_NBIOT(GSM, UMTS AND NB-IoT), GSM_AND_LTE_AND_NBIOT(GSM, LTE AND NB-IoT), UMTS_AND_LTE_AND_NBIOT(UMTS, LTE AND NB-IoT), GSM_AND_UMTS_AND_LTE_AND_NBIOT(GSM , UMTS, LTE AND NB-IoT) Unit: None Actual Value Range: GSM_AND_UMTS, UMTS, GSM, GSM_AND_LTE, LTE, UMTS_AND_LTE, GSM_AND_UMTS_AND_LTE, LTE_TDD, GSM_AND_LTE_TDD, UMTS_AND_LTE_TDD, LTE_AND_LTE_TDD, GSM_AND_UMTS_AND_LTE_TDD, GSM_AND_LTE_AND_LTE_TDD, UMTS_AND_LTE_AND_LTE_TDD, GSM_AND_UMTS_AND_LTE_AND_LTE_TDD, NBIOT, GSM_AND_NBIOT, UMTS_AND_NBIOT, LTE_AND_NBIOT, GSM_AND_UMTS_AND_NBIOT, GSM_AND_LTE_AND_NBIOT, UMTS_AND_LTE_AND_NBIOT, GSM_AND_UMTS_AND_LTE_AND_NBIOT Default Value: GSM(GSM)

Issue 01 (2017-03-10)


77


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

RS


ADD RRU

None

None

Meaning: Indicates the working standard of the RRU or RFU.

MOD RRU

GUI Value Range: TDL(LTE_TDD), TL(TDS_TDL), LO(LTE_FDD), LFTD(LTE_FDD_TDD), WL(WiMAX_LTE), CL(CDMA_LTE), GO(GSM_ONLY), GT(GSM_LTE_TDD), GL(GSM_LTE), GLFTD(GSM_LTE_FDD_TDD), UO(UMTS_ONLY), UT(UMTS_LTE_TDD), UL(UMTS_LTE), ULFTD(UMTS_LTE_FDD_TDD), CU(CDMA_UMTS), GU(GSM_UMTS), GUT(GSM_UMTS_LTE_TDD), GUL(GSM_UMTS_LTE), GULFTD(GSM_UMTS_LTE_FDD_TDD), MO(NBIoT), LM(LTE_FDD_NB-IoT), CM(CDMA_NBIoT), CLM(CDMA_LTE_FDD_NB-IoT), GM(GSM_NB-IoT), GLM(GSM_LTE_FDD_NBIoT), UM(UMTS_NB-IoT), ULM(UMTS_LTE_FDD_NB-IoT), GUM(GSM_UMTS_NB-IoT), GULM(GSM_UMTS_LTE_FDD_NB-IoT), RO(RFA_ONLY), TR(LTE_TDD_RFA), LR(LTE_FDD_RFA), LFTDR(LTE_FDD_TDD_RFA), UR(UMTS_RFA), UTR(UMTS_LTE_TDD_RFA), ULR(UMTS_LTE_FDD_RFA), ULFTDR(UMTS_LTE_FDD_TDD_RFA)

LST RRU

Unit: None Actual Value Range: TDL, TL, LO, LFTD, WL, CL, GO, GT, GL, GLFTD, UO, UT, UL, ULFTD, CU, GU, GUT, GUL, GULFTD, MO, LM, CM, CLM, GM, GLM, UM, ULM, GUM, GULM, RO, TR, LR, LFTDR, UR, UTR, ULR, ULFTDR Default Value: None AT

BSC691 0


GBFD-1 11202

O&M of BTS

Meaning: The parameter is access type of RXU. Local port access GTMU/UBRI/UBBP/GBBP/BTS3900E connected to RRU/RFU by CPRI; Peer port means GTMU gathered to the other type of base band board connect to RRU/RFU by IDX2. GUI Value Range: LOCALPORT(local port), PEERPORT(peer port) Unit: None Actual Value Range: LOCALPORT, PEERPORT Default Value: LOCALPORT(local port)

Issue 01 (2017-03-10)


78


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

AT

BSC690 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

Meaning: The parameter is access type of RXU. Local port access GTMU/UBRI/UBBP/GBBP/BTS3900E connected to RRU/RFU by CPRI; Peer port means GTMU gathered to the other type of base band board connect to RRU/RFU by IDX2.

MOD BTSRX UCHAI N

GUI Value Range: LOCALPORT(local port), PEERPORT(peer port) Unit: None Actual Value Range: LOCALPORT, PEERPORT Default Value: LOCALPORT(local port)

AT


ADD RRUC HAIN

None

None

MOD RRUC HAIN LST RRUC HAIN

Meaning: Indicates the access type of the board on an RRU chain/ring. When Access Type is set to LOCALPORT(local port), the BBP connects to the board on an RRU chain/ring through the CPRI port. When Access Type is set to PEERPORT(peer port), the local BBP connects to the peer BBP through the IDX2 port on the backplane and the peer BBP connects to a board on an RRU chain/ring. GUI Value Range: LOCALPORT(local port), PEERPORT(peer port) Unit: None Actual Value Range: LOCALPORT, PEERPORT Default Value: LOCALPORT(local port)

HCN

BSC691 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

GUI Value Range: 0~62 Unit: None

MOD BTSRX UCHAI N HCN

BSC690 0


Issue 01 (2017-03-10)

Meaning: Number of the cabinet where the board connected to the RXU chain or ring is installed.

Actual Value Range: 0~62 Default Value: None GBFD-1 11202

O&M of BTS

Meaning: Number of the cabinet where the board connected to the RXU chain or ring is installed. GUI Value Range: 0~62 Unit: None Actual Value Range: 0~62 Default Value: None


79


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

HCN


ADD RRUC HAIN

None

None

Meaning: Indicates the cabinet number of the board where the head CPRI port is located. GUI Value Range: 0~15

MOD RRUC HAIN

Unit: None

DSP RRUC HAINP HYTOP O

Default Value: 0


LST RRUC HAIN HSRN

BSC691 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS


MOD BTSRX UCHAI N HSRN

BSC690 0

ADD BTSRX UCHAI N

Unit: None Actual Value Range: 0~254 Default Value: None GBFD-1 11202

O&M of BTS


ADD RRUC HAIN

Meaning: Number of the subrack where the board connected to the RXU chain or ring is installed. The subrack No. is unique in a BTS. GUI Value Range: 0~254

MOD BTSRX UCHAI N HSRN

Meaning: Number of the subrack where the board connected to the RXU chain or ring is installed. The subrack No. is unique in a BTS.

Unit: None Actual Value Range: 0~254 Default Value: None None

None

Meaning: Indicates the subrack number of the board where the head CPRI port is located. GUI Value Range: 0~1,60~254

MOD RRUC HAIN

Unit: None


Default Value: 0

Actual Value Range: 0~1,60~254

LST RRUC HAIN

Issue 01 (2017-03-10)


80


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

HSN

BSC691 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

Meaning: Number of the slot where the board connected to the RXU chain or ring is installed. The slot No. is unique in a BTS. GUI Value Range: 0~23

MOD BTSRX UCHAI N HSN

BSC690 0

ADD BTSRX UCHAI N

Unit: None Actual Value Range: 0~23 Default Value: None GBFD-1 11202

O&M of BTS


MOD BTSRX UCHAI N HSN


ADD RRUC HAIN

Meaning: Number of the slot where the board connected to the RXU chain or ring is installed. The slot No. is unique in a BTS. Unit: None Actual Value Range: 0~23 Default Value: None

None

None

Meaning: Indicates the slot number of the board where the head CPRI port is located. GUI Value Range: 0~6

MOD RRUC HAIN

Unit: None


Default Value: None


LST RRUC HAIN HPN

BSC691 0


Issue 01 (2017-03-10)

GBFD-1 11202

O&M of BTS

Meaning: Number of the optical port on the board connected to the RXU chain or ring. GUI Value Range: 0~5 Unit: None Actual Value Range: 0~5 Default Value: None


81


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

HPN

BSC690 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

Meaning: Number of the optical port on the board connected to the RXU chain or ring. GUI Value Range: 0~5 Unit: None

MOD BTSRX UCHAI N HPN


ADD RRUC HAIN

Actual Value Range: 0~5 Default Value: None None

None

Meaning: Indicates the number of the head CPRI port. GUI Value Range: 0~11 Unit: None

MOD RRUC HAIN

Actual Value Range: 0~11 Default Value: None

DSP RRUC HAINP HYTOP O LST RRUC HAIN

RCN


ADD RRUC HAIN

None

None

Meaning: Indicates the ID of the RRU chain. It uniquely identifies a chain within a base station. GUI Value Range: 0~249

DSP CPRIL BR

Unit: None

DSP RRUC HAIN

Default Value: None


LST RRUC HAIN MOD RRUC HAIN RMV RRUC HAIN STR CPRIL BRNEG

Issue 01 (2017-03-10)


82


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

LSN


ADD RRUC HAIN

None

None

Meaning: Indicates the slot number of the converged party in CPRI MUX. If this parameter is set to 255, the slot number of the converged party is not specified. When the converging party is in a BBU3900, this parameter can be left unspecified. When the converging party is in a BBU3910, this parameter must be specified.

MOD RRUC HAIN LST RRUC HAIN

GUI Value Range: 0~6,255 Unit: None Actual Value Range: 0~6,255 Default Value: 255

RCN

BSC691 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

Meaning: Number of the RXU chain or ring. The value scope is 0~11 for Non-SingleRAN BTS and 0~249 for SingleRAN BTS. The RXU chain No. is unique in the same BTS.

MOD BTSRX UCHAI N


RMV BTSRX UCHAI N

Default Value: None

Unit: None Actual Value Range: 0~249

SPT BTSRX UCHAI N RCN

BSC690 0

ADD BTSRX UCHAI N

GBFD-1 11202

O&M of BTS

Meaning: Number of the RXU chain or ring. The value scope is 0~11 for Non-SingleRAN BTS and 0~249 for SingleRAN BTS. The RXU chain No. is unique in the same BTS.

MOD BTSRX UCHAI N


RMV BTSRX UCHAI N

Default Value: None

Unit: None Actual Value Range: 0~249

SPT BTSRX UCHAI N

Issue 01 (2017-03-10)


83


16 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

RCN


ADD RRU

None

None

Meaning: Indicates the ID of the RRU or RFU chain/ ring.

BSC691 0

ADD BTSRX UBRD

RXUC HAINN O

LST RRU

GUI Value Range: 0~249 Unit: None Actual Value Range: 0~249 Default Value: None GBFD-1 11202

O&M of BTS

Meaning: Number of the RXU chain where the board is located GUI Value Range: 0~249

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None


MOD BTSRX UBRD QUICK RMV BTSRX UBRD RXUC HAINN O

BSC690 0

ADD BTSRX UBRD

GBFD-1 11202

O&M of BTS

Meaning: Number of the RXU chain where the board is located GUI Value Range: 0~249

MOD BTSRX UBRD

Unit: None

MOD BTSRX UBRDP OS

Default Value: None


MOD BTSRX UBRD QUICK RMV BTSRX UBRD

Issue 01 (2017-03-10)


84


17 Counters

17

Counters

There are no specific counters associated with this feature.

Issue 01 (2017-03-10)


85


18 Glossary

18

Glossary

For the acronyms, abbreviations, terms, and definitions, see the Glossary.

Issue 01 (2017-03-10)


86


19 Reference Documents

19

Reference Documents

1.

3900 Series Base Station Technical Description

2.

Installation Guide of relevant base stations

3.

Site Maintenance Guide of relevant base stations

4.

RF Unit and Topology Management Feature Parameter Description

5.

RMU Feature Parameter Description

6.

BSC6900 GSM MML Command Reference

7.

3900 Series Base Station MML Command Reference

8.

3900 Series Base Station Alarm Reference

Issue 01 (2017-03-10)


87

CPRI MUX(SRAN12.1_01)

Recommend Documents