dn70598907.pdf

Nokia Siemens Networks Flexi BSC, S14, Site documentation, issue 02

Guide to Flexi BSC Site Documents DN70598907 Issue 1-2

Guide to Flexi BSC Site Documents

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2009/10/19. All rights reserved

f

Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures. Non-observance of these conditions and the safety instructions can result in personal injury or in property damage. Therefore, only trained and qualified personnel may install and maintain the system. The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards.

The same text in German: Wichtiger Hinweis zur Produktsicherheit In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Spannung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen. Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverletzungen und Sachschäden führen. Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet. Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen.

2

Id:0900d8058063f988

DN70598907 Issue 1-2


Table of Contents This document has 15 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DN70598907 Issue 1-2

1 1.1 1.2 1.3 1.3.1 1.3.2 1.3.3 1.3.4

Site Documentation for Flexi BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Site Documentation deliveries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Site Documentation maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 New and updated documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Introductory documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation planning documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Equipment and cable lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 2.1 2.2 2.2.1 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.3.7 2.3.8 2.3.9 2.3.10 2.4 2.4.1 2.4.2 2.4.3 2.4.4

Contents of Site Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introductory documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation planning documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Site Requirements for Flexi BSC and TCSM. . . . . . . . . . . . Installation documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking the DX 200 cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing Flexi BSC and TCSM3i. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Work Check List for Flexi BSC and TCSM3i . . . . . . . . . . . . Jumper Settings of the Plug-in Units in Flexi BSC and TCSM3i . . . . . . Jumper Settings of the Cartridges in Flexi BSC. . . . . . . . . . . . . . . . . . . Cabling instructions for First-delivery Flexi BSC . . . . . . . . . . . . . . . . . . Connector Panels and External Cables in Flexi BSC and TCSM3i . . . . Grounding of External Interface Cables. . . . . . . . . . . . . . . . . . . . . . . . . Swapping BSC and TCSM with Flexi BSC and TCSM3i . . . . . . . . . . . . Equipment and cable lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equipment List for Flexi BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interconnection Cables in Flexi BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . Use of LAN ports in Flexi BSC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use of PCM Circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 11 11 11 11 11 11 11 11 11 11 12 12 12 12 12 12 12 12 13

3 3.1 3.2 3.3

Use of Site Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flexi BSC and the use of Site Documentation. . . . . . . . . . . . . . . . . . . . Example 1: New delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 2: Upgrade delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 14 15 15

Id:0900d8058063f988

3


List of Figures Figure 1

4

Flexi BSC documentation and its delivery media . . . . . . . . . . . . . . . . . . . 9

Id:0900d8058063f988

DN70598907 Issue 1-2


List of Tables Table 1

DN70598907 Issue 1-2

Implementation phases and use of site documents . . . . . . . . . . . . . . . 14

Id:0900d8058063f988

5


6

Id:0900d8058063f988

DN70598907 Issue 1-2


Summary of changes

Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. Changes between issues 1-2 and 1-1 Editorial corrections. Changes between issues 1-1 and 1-0 The list of updated documernts updated. Changes for issue 1-0 This is the first issue of Guide to Flexi BSC Site Documents. The documents included in the Guide to Flexi BSC Site Documents contain information on Flexi BSC first deliveries and on BSC3i to Flexi BSC upgrade deliveries.

DN70598907 Issue 1-2

Id:0900d8058063f971

7

Site Documentation for Flexi BSC


1 Site Documentation for Flexi BSC 1.1

Site Documentation deliveries In release S14, the site documents for Flexi BSC are available in a single documentation set, Nokia Siemens Networks Flexi BSC, Rel.S14, Site Documentation, v.2: • •

in NOLS (Nokia Online Services) in PDF-format on CD-ROM as a part of new network element deliveries

Site documentation in paper format is delivered in ECO folders, and can be ordered separately. Related Flexi BSC documentation In addition to the site documents, hardware-related documentation for Flexi BSC is included in the following publications: •

•

•

•

Hardware Revision List for Flexi BSC, published as PDF in NOLS The Hardware Revision List provides release compatibility information for network element hardware. It lists all the accepted hardware products including interchangeability codes for each release. ESB26 User Guide, published as PDF in NOLS This guide provides information for setting up and configuring the ESB26 LAN switch. ESB24 User Guide, published as PDF in NOLS This guide provides information for setting up and configuring the ESB24 LAN switch. Product Documentation The Product Documentation consists of instructions for implementation, normal daily operations, maintenance, and troubleshooting of the Flexi BSC. It contains instructions, descriptions, and reference information and is available in both online and PDF views. The Product Documentation is delivered via NOLS as Nokia Siemens Networks Electronic Documentation (NED) and on a CD-ROM with the network element delivery. The Product Documentation includes hardware-related documents, such as Engineering for Flexi BSC, Commissioning BSC3i and Flexi BSC, Integration, Replacing Plug-in Units and Other Hardware Units, and Hardware Configuration Management.

The following figure shows the Flexi BSC documentation and its different delivery media.

8

Id:0900d8058063f86d

DN70598907 Issue 1-2



ESB26, ESB24 USER GUIDES NOLS

PRODUCT DOCUMENTATION (NED)

SITE DOCUMENTATION

HARDWARE REVISION LIST

NOLS

CD-ROM

NOLS

Paper Binder*)

DN70312002

Figure 1

CD-ROM

NOLS

*) Optional

Flexi BSC documentation and its delivery media

Changes in Site Documentation set in S14.0 This is the second site set for Flexi BSC. Site Documentation codes and versioning The Site Documentation set has a code which is printed on the cover pages of the documents and the binder label. The code shows the revision of the document set. Each document has a document identification (DN number) and issue number. When updates are made to a document, the issue number is increased. The latest issue contains the changes made to the previous issues.

1.2

Site Documentation maintenance The site documents are updated for each release of the network element. After the first Site Documentation set for a release is published, the updates to the site documents are published as follows: •

•

•

Minor changes and updates to the documents are delivered as Change Deliveries to the Site Documentation set in NOLS, for example, Nokia Siemens Networks Flexi BSC, Rel.S14, Site Documentation, v.1, Doc Change Delivery 1. The CD-ROM set delivered with the network element hardware or the paper binder delivered separately is not updated at the same time and thus does not contain the updated versions of the documents. If the changes during the release are extensive, the Site Documentation set is republished with a new revision code. In this case, the CD-ROM set delivered with the network element hardware, the paper binder delivered separately and the Site Documentation set in NOLS are updated. Also, all the updated documents in the intermediate Change Deliveries are included in the updated Site Documentation set. The updated site documents are also included in the Product Documentation NED update packages, available in NOLS.

☞ The latest issues of the site documents are always available in NOLS, in the Site Documentation set or in the Change Deliveries to the Site Documentation set. It is highly recommended to check from time to time that you are using the latest document versions. Crosscheck your documents with the latest Document list and replace old document versions with new ones.

DN70598907 Issue 1-2

Id:0900d8058063f86d

9


1.3


New and updated documents The following tables list the site documents for the S14 Flexi BSC. The tables include the name, DN number, and issue of the documents.

1.3.1

Introductory documents

Document

DN number

Issue


DN70598907

1-1

1.3.2

Installation planning documents

Document

DN number

Issue

Installation Site Requirements for Flexi BSC and TCSM

DN70594326

1-0

1.3.3

Note

Installation documents

Document

DN number

Issue

Unpacking the DX 200 Cabinet

DN99582178

2-5

Warnings and Cautions

DN70219408

2-0

Jumper Settings of the Plug-in Units in Flexi BSC and TCSM3i

DN70630644

1-2

1.3.4

Note

Note

Equipment and cable lists

Document

DN number

Issue

Note

Interconnection Cables in Flexi BSC

DN70613549

1-2

New and upgrade deliveries

Use of LAN Ports in Flexi BSC

DN70589749

1-1

New and upgrade deliveries

Use of PCM Circuits in Flexi BSC and Combined BSC/TCSM installation option (GSW2KB-A)

DN70637319

1-1

New deliveries

Use of PCM Circuits in Flexi BSC and Combined BSC/TCSM installation option (GSW2KB)

DN70640767

1-1

Upgrade deliveries

10

Id:0900d8058063f86d

DN70598907 Issue 1-2


Contents of Site Documentation

2 Contents of Site Documentation 2.1

Introductory documents Guide to Flexi Site Documents shows the contents of Site Documentation.

2.2 2.2.1

Installation planning documents Installation Site Requirements for Flexi BSC and TCSM Installation Site Requirements for Flexi BSC and TCSM provides the information needed for the installation planning for the equipment, including network element power supply, environmental conditions, ventilation, site layout planning and cabling.

2.3 2.3.1

Installation documents Warnings and Cautions Warnings and Cautions details the recommended safety precautions which are to be followed when working with the equipment described in customer documentation.

2.3.2

Unpacking the DX 200 cabinet Unpacking the DX 200 cabinet provides the basic information needed for unpacking the DX 200 network elements from their carrier packages. It is advisable to read this document before unpacking the network element from the carrier packages.

2.3.3

Installing Flexi BSC and TCSM3i Installing Flexi BSC and TCSM3i gives information on how to prepare for and carry out the actual cabinet and plug-in unit installation. Also grounding and power supply issues are covered in this document.

2.3.4

Installation Work Check List for Flexi BSC and TCSM3i Installation Work Check List for Flexi BSC and TCSM3i provides a checklist for the installation phases of the Flexi BSC and TCSM3i. The Certificate of Completion is enclosed in this document too.

2.3.5

Jumper Settings of the Plug-in Units in Flexi BSC and TCSM3i Jumper Settings of the Plug-in Units in Flexi BSC and TCSM3i provides the basic information needed for checking and setting the jumpers of the plug-in units in the Flexi BSC and TCSM3i.

2.3.6

Jumper Settings of the Cartridges in Flexi BSC Jumper Settings of the Cartridges in Flexi BSC provides the basic information needed for setting the various jumper settings (strappings) of the cartridges in the Flexi BSC.

DN70598907 Issue 1-2

Id:0900d8058063f87a

11


2.3.7


Cabling instructions for First-delivery Flexi BSC Cabling instructions for First-delivery Flexi BSC describes the basic principles of routing intracabinet cables in the Flexi BSC. Also, other general information regarding cables is given.

2.3.8

Connector Panels and External Cables in Flexi BSC and TCSM3i Connector Panels and External Cables in Flexi BSC and TCSM3i gives information on the connector panels and the related external cables used in the Flexi BSC and TCSM3i.

2.3.9

Grounding of External Interface Cables Grounding of External Interface Cables describes the grounding principles for the external LAN cables and PCM trunk cables when connected to the DX 200 network elements in the E1 (ETSI) environment.

2.3.10

Swapping BSC and TCSM with Flexi BSC and TCSM3i Swapping BSC and TCSM with Flexi BSC and TCSM3i describes the overall process for swapping an M92 mechanic-based BSC or TCSM with an M98 mechanic-based Flexi BSC or TCSM3i.

2.4 2.4.1

Equipment and cable lists Equipment List for Flexi BSC Equipment List for Flexi BSC provides information on all hardware products installed in the cabinets of the Flexi BSC. It includes information on the positions of plug-in units, cartridges, connectors and terminators in the cabinet. The List presents the maximum configuration.

2.4.2

Interconnection Cables in Flexi BSC Interconnection Cables in Flexi BSC provides a list of all the cables contained in the firstdelivery Flexi BSC and in the upgraded Flexi BSC as well as those needed in the transmission protection to equipment protection upgrades. It gives the positions and routing of the intracabinet cables running inside each cabinet and intercabinet cables running between the cabinets. The intracabinet cables part of this document is used mainly for checking purposes since intracabinet cables are installed at the factory.

2.4.3

Use of LAN ports in Flexi BSC Use of LAN ports in Flexi BSC contains a list of all the LAN ports provided by the LAN Switch unit (SWU) in the Flexi BSC, as well as other HW-specific information concerning LAN ports. The document is intended to be used mainly during LAN port configuration; however, it also serves as a basis for the influence of protection principles on hardware realisation.

12

Id:0900d8058063f87a

DN70598907 Issue 1-2


2.4.4


Use of PCM Circuits Two new Use of PCM Circuits documents are available. One (Use of PCM Circuits in Flexi BSC and Combined BSC/TCSM (GSW2KB-A)) is for new deliveries and the other (Use of PCM Circuits in Flexi BSC and Combined BSC/TCSM (GSW2KB)) is for BSC3i to Flexi BSC upgrade deliveries. Use of PCM Circuits documents provide lists of all PCM (2 Mbit/s) circuits from the group switch towards various functional units.

DN70598907 Issue 1-2

Id:0900d8058063f87a

13

Use of Site Documentation


3 Use of Site Documentation The Site Documentation provides information on the hardware of the network element in its maximum configuration.

3.1

Flexi BSC and the use of Site Documentation The following sections introduce concepts used in the Site Documentation for describing the different delivery and use cases of the Flexi BSC. New delivery A new delivery refers to the first delivery of a Flexi BSC in a certain system release. The new delivery contains the latest hardware and configuration options of the network element. The Site Documentation set provides information on all the configurations but there are no delivery-specific site documents. Upgrade delivery An upgrade delivery refers to a case where an existing network element of a certain system release is upgraded to another system release. The site documents are part of an upgrade delivery, and the latest issues of the site documents are available in NOLS as well. Configuration options The Flexi BSC can be configured to meet different capacity requirements: the capacity of the Flexi BSC can be expanded with different kinds of capacity steps. The site documents provide information on all the alternative configurations and capacity steps. Implementation phases and use of site documents The Site Documentation set includes documents for different implementation and usage phases of the Flexi BSC. The following table shows which are the main documents used in each phase.

Document title

Implementation phase Planning Installation and ordering planning

Installing

Installation Site Requirements for Flexi BSC and TCSM

x

x

Warnings and Cautions

x

x

x

Unpacking the DX 200 Cabinet

x

x

Installing Flexi BSC and TCSM3i

x

x

Jumper Settings of the Plug-in Units in Flexi BSC and TCSM3i

Commissioning

x

x

Equipment List for Flexi BSC

x

x

x

Cabling Instructions for First-delivery Flexi BSC

x

x

x

Interconnection Cables in Flexi BSC

x

x

x

Table 1

14

Implementation phases and use of site documents

Id:0900d8058063f8c9

DN70598907 Issue 1-2


Document title

Use of Site Documentation

Implementation phase Planning Installation and ordering planning

Connector Panels and External Cables in Flexi BSC and TCSM3i

Installing x

x

Use of LAN Ports in Flexi BSC

x

x

Use of PCM Circuits

x

x

Table 1

x

Commissioning

Implementation phases and use of site documents (Cont.)

3.2

Example 1: New delivery The Flexi BSC has been ordered as a new delivery. The Site Documentation set is part of the delivery but it can be delivered in ECO folders as well if ordered separately. The delivery also includes a list of the delivered sales items. Use the delivery list to check that the delivery contains all the ordered items. First, study the document Unpacking the DX 200 Cabinet for instructions on how to properly unpack the cabinets from their carrier packages. Installing Flexi BSC and TCSM3i explains the basic principles of installing the cabinets. Note that the Flexi BSC can have different possible cabinet configurations; the accepted alternatives are shown in the Installation Site requirements for Flexi BSC and TCSM and in the Engineering for Flexi BSC. The intracabinet cables (cabling running inside a cabinet or between a cabinet and a cabling cabinet) are delivered completely installed in the cabinets. There is no need to do anything to these cables but if you want to check them, the Interconnection Cables in Flexi BSC and the Cabling Instructions for Flexi BSC can be used for this purpose. Note that there are no intercabinet cables (cabling that is led directly from one cabinet to another) in the first-delivery Flexi BSC. In the commissioning phase, use the Commissioning and Commissioning checklist documents. These documents are included in the Product Documentation (NED) library. Note, however, that also site documents are needed during commissioning, for example Jumper Settings of the Plug-in Units in Flexi BSC and TCSM3i and Interconnection Cables in Flexi BSC.

3.3

Example 2: Upgrade delivery In an upgrade delivery, an existing BSC3i 1000/2000 or BSC3i 660 is upgraded to Flexi BSC. The delivery includes, for example, functional units and cables. The Site Documentation set is part of an upgrade delivery - and the latest issues of the site documents are available in NOLS as well. As described in Example 1, consult first the documents Unpacking the DX 200 Cabinet and Installing Flexi BSC and TCSM3i . Next, use the Interconnection cables in Flexi BSC document to check the factory installed cabling and to remove or install cables in accordance with the correct routing. Check against the Hardware Revision List (available in NOLS) that the network element's plug-in units and other products are of correct interchangeability. Also, consult Jumper Settings of the Plug-in Units in Flexi BSC and TCSM3i when checking the jumper setting of the plug-in units.

DN70598907 Issue 1-2

Id:0900d8058063f8c9

15

dn70598907.pdf

Recommend Documents