Digital Visitor counter using 8051 microcontroller (AT89C52)
Abstract:: Abstract This project titled “Microcontroller based Bidirectional Visitor counter” is designed and presented in order to count the visitors of an auditorium, hall, offices, malls, sports venue, etc. The system counts both the entering and exiting visitor of the auditorium or hall or other place, where it is placed. Depending upon the interrupt from the sensors, the system identifies the entry and exit of the visitor. On the successful implementation of the system, it displays the number of visitor present in the auditorium or hall. This system can be economically implemented in all the places where the visitors have to be counted and controlled. Since counting the visitors helps to maximize the efficiency and effectiveness of employees, floor area and sales potential of an organization, etc.
Description:: Description A counter that can c an change its state in either direction, under control of an up up – –down down selector input, is known as an up – –down down counter. The circuit given here can count numbers from 0 to 9999 in up and down modes depending upon the state of the selector. It can be used to count the number of persons entering a hall in the up mode at entrance gate. In the down mode, it can count the number of persons leaving the hall by decrementing the count at exit gate. It can also be used at gates of parking areas and other public places. This circuit divided in three parts: sensor, controller and counter display. The sensor would observe an interruption and provide an input to the controller which would run the counter in up/down mode depending upon the selector setting. The same count is displayed on a set of 7-segment displays through the controller. In this circuit, two infrared (IR) sensor modules are used each for up and down counting, respectively. respectively. Whenever an interruption interruption is observed observed by the first IR sensor, it increments the counter value. Similarly, when the second sensor detects an obstacle, the count is decremented. The count value is calculated depending upon the sensor‟s input and is displayed on a set of four seven segment displays by using the concept of multiplexing. The data pins of each 7-segment display are connected to port P 2 of the microcontroller AT89C51. The first four pins of port P 1 (P1^0-P1^3) are connected to control pins to enable a particular 7-segment. P 1^5 & P1^6 are configured as input pins at which the sensors are connected. The sensor inputs are defined as up and down selector modes for the counter in the code. Each time the first sensor is blocked, it gives a high signal at P 1^5 and the count value gets incremented. The value gets decremented when P 1^6, connected to second sensor, gives high input. At each step, the value of the counter is sent to be displayed on the segments.
Block Diagram: Block Diagram:
Sensors
Logic Control Circuit
Microcontroller AT89C52
Power Supply +5V
Sensor arrangement arrangement at the way:
Enter
IR TX1
RX1
IR TX2
RX2
Exit
Display
Circuit Diagram:
Circuit Components: Transistor BC547 BC547 is an NPN bi-polar junction transistor. A transistor, stands for transfer of resistance, is commonly used to amplify current. A small current at its base controls a larger current at collector & emitter terminals. BC547 is mainly used for amplification and switching purposes. It has a maximum current gain of 800. Its equivalent transistors are BC548 and BC549.
Seven Segment Display A seven segment display is the most basic electronic display device that can display digits from 0-9. They are laid out as a squared-off figure ‘8’. Every LED is assigned a name from 'a' to 'h' and is identified by its name. Seven LEDs 'a' to 'g' are used to display the numerals while eighth LED 'h' is used to display the dot/decimal.
AT89C51 Microcontr Microcontroller oller AT89C51 is an 8-bit microcontroller and belongs to Atmel's 8051 family. ATMEL 89C51 has 4KB of Flash programmable and erasable read only memory (PEROM) and 128 bytes of RAM. It can be erased and program to a maximum of 1000 times.
Infrared LED An IR LED, also known as IR transmitter, is a special purpose LED that transmits transm its infrared rays in the range ran ge of 760 nm wavelength. Such LEDs are usually made of gallium arsenide or aluminium gallium arsenide. They, along with IR receivers, are commonly used as sensors.
Light emitting diodes Light emitting diodes (LEDs LEDs)) are semiconductor light sources. The light emitted from LED LEDs s varies from visible to infrared and ultraviolet regions. They operate on low voltage and power. LEDs are one of the most common electronic components and are mostly used as indicators in circuits.
Transistor BC547:
Description: BC547 is an NPN bi-polar junction transistor. A transistor, stands for transfer of resistance, is commonly used to amplify current. A small current at its base controls a larger current at collector & emitter terminals. BC547 is mainly used for amplification and switching purposes. It has a maximum current gain of 800. Its equivalent transistors are BC548 and BC549. The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. This is known as the biasing. For amplification applications, the transistor is biased such that it is partly on for all input conditions. The input signal at base is amplified and taken at the emitter. BC547 is used in common emitter configuration for amplifiers. The voltage divider is the commonly used biasing mode. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. In the absence of base signal, it gets completely off.
Pin Diagram:
Seven Segment Display: Description: A seven segment display is the most basic electronic display device that can display digits from 0-9. They find wide application in devices that display numeric information like digital clocks, radio, microwave ovens, electronic meters etc. The most common configuration configuration has an array of eight LEDs arranged in a special pattern to display these digits. They are laid out as a squared- off figure „8‟. Every LED is assigned a name from 'a' to 'h' and is identified by its name. Seven LEDs 'a' to 'g' are used to display the numerals while eighth LED 'h' is used to display the dot/decimal. A seven segment is generally available in ten pin package. While eight pins correspond to the eight LEDs, the remaining two pins (at middle) are common and internally shorted. These segments come in two configurations, namely, Common cathode (CC) and Common anode (CA). In CC configuration, the negative terminals of all LEDs are connected to the common pins. The common is connected to ground and a particular LED glows when its corresponding pin is given high. In CA arrangement, the common pin is given a high logic and the LED pins are given low to display a number.
Pin Diagram:
AT89C51 Microcontroller:
Description: AT89C51 is an 8-bit microcontro microcontroller ller and belongs to Atmel's 8051 family. ATMEL 89C51 has 4KB of Flash programmable and erasable read only memory (PEROM) and 128 bytes of RAM. It can be erased and program to a maximum of 1000 times. In 40 pin AT89C51, there are four ports designated as P1, P2, P3 and P0. All these ports are 8-bit bi-directional ports, i.e. i.e.,, they can be used as both input and output ports. Except P0 which needs external pull-ups, rest of the ports have internal pullups. When 1s are written to these port pins, they are pulled high by the internal pull-ups and can be used as inputs. These ports are also bit addressable and so their bits can also be accessed individually. Port P0 and P2 are also used to provide low byte and high byte addresses, respectively, when connected to an external memory. Port 3 has multiplexed pins for special functions like serial communication, hardware interrupts, timer inputs and read/write operation from external memory. AT89C51 has an inbuilt UART for serial communication. It can be programmed to operate at different baud rates. Including two timers & hardware interrupts, it has a total of six interrupts.
Pin Diagram:
Pin Description: Pin No
Function
Name
1 2 3 4 5 6 7 8 9
P1.0 P1.1 P1.2 P1.3 P1.4 P1.5
8 bit input/output port (P 1) pins
P1.6 P1.7 Reset
Reset pin; Active high
10
Input (receiver) for serial communication
RxD
P3.0
11
Output (transmitter) for serial communication
TxD
P3.1
12 13 14
External interrupt 1 External interrupt 2 Timer1 external input
Int0 Int1 T0
15 16 17 18 19 20
Timer2 external input Write to external data memory Read from external data memory
T1 Write Read
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
8 bit input/output port (P3) pins
Quartz crystal oscillator (up to 24 MHz) Ground (0V)
8 bit input/output port (P 2) pins / High-order address bits when interfacing with external memory
P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 Crystal 2 Crystal 1 Ground P2.0/ A8 P2.1/ A9 P2.2/ A10 P2.3/ A11 P2.4/ A12 P2.5/ A13
Program store enable; Read from external program memory Address Latch Enable Program pulse input during Flash programming External Access Enable; Vcc for internal program executions
P2.6/ A14 P2.7/ A15 PSEN ALE Prog EA
Programming enable voltage; 12V (during Flash programming)
Vpp
8 bit input/output port (P 0) pins
36 37 38 39
Low-order address bits when interfacing with external memory
40
Supply voltage; 5V (up to 6.6V)
P0.7/ P0.6/ P0.5/ P0.4/
AD7 AD6 AD5 AD4
P0.3/ P0.2/ P0.1/ P0.0/
AD3 AD2 AD1 AD0
Vcc
Infrared LED:
Description: An IR LED, also also known as IR transmitter, transmitter, is a special purpose LED that transmits infrared rays in the range of 760 nm wavelength. Such LEDs are usually made of gallium arsenide or aluminium gallium arsenide. They, along with IR receivers, are commonly used as sensors. The appearance is same as a common LED. LED. Since the human eye cannot see the infrared radiations, it is not possible for a person to identify whether the IR LED is working or not, unlike a common LED. To overcome this problem, the camera on a cellphone can be used. The camera can show us the IR rays being emanated from the IR LED in a circuit.
Pin Diagram:
Light Emitting Diodes:
Description: Light emitting diodes (LEDs) are semiconductor light sources. The light emitted from LEDs varies from visible to infrared and ultraviolet regions. They operate on low voltage and power. LEDs are one of the most common electronic components and are mostly used as indicators in circuits. They are also used for luminance and optoelectronic optoelectro nic applications. Based on semiconductor diode, LEDs emit photons when electrons recombine with holes on forward biasing. The two terminals of LEDs are anode (+) and cathode (-) and can be identified by their size. The longer leg is the positive terminal or anode and shorter one is negative terminal. The forward voltage of LED (1.7V-2.2V) is lower than the voltage supplied (5V) to drive it in a circuit. Using an LED as such would burn it because a high current would destroy its p-n gate. Therefore a current limiting resistor is used in series with LED. Without this resistor, either low input voltage (equal to forward voltage) or PWM (pulse width modulation) is used to drive the LED. Get details about internal structure of a LED.
Pin Diagram:
Program: // Program to make a bidirectional visitor counter using IR sensor
#include #define msec 1 unsigned int num=0; sbit dig_ctrl_4=P1^3; dig_ctrl_4=P1^3;
//declare the the control pins of seven segments segments
sbit dig_ctrl_3=P1^2; sbit dig_ctrl_2=P1^1; sbit dig_ctrl_1=P1^0; unsigned int digi_val[10]={0x40,0xF9,0x24,0x30,0x19,0x12,0x02, digi_val[10]={0x40,0xF9, 0x24,0x30,0x19,0x12,0x02,0xF8,0x00,0x10}; 0xF8,0x00,0x10}; unsigned int dig_1,dig_2,dig_3,d dig_1,dig_2,dig_3,dig_4,test=0; ig_4,test=0; unsigned char dig_disp=0; sbit up=P3^5; up=P3^5;
//up pin to make counter count up
sbit down=P3^6; down=P3^6;
void init()
// to initialize the output pins and Timer0
{ up=down=1; dig_ctrl_4 = 0; dig_ctrl_3 = 0; dig_ctrl_2 = 0; dig_ctrl_1 = 0; TMOD=0x01; TL0=0xf6; TH0=0xFf; IE=0x82;
//down pin to make counter count down
TR0=1; }
void delay()
//To provide a small time delay
{ TMOD=0x01; TL0=0x36; TH0=0xF6; TR0=1; while(TF0==0); TR0=0; TF0=0; }
void display() interrupt 1 // Function to display the digits on seven segment. For more details refer seven segment multiplexing. { TL0=0x36; TH0=0xf6; P2=0xFF; dig_ctrl_1 = dig_ctrl_3 = dig_ctrl_2 = dig_ctrl_4 = 0; dig_disp++; dig_disp=dig_disp%4; switch(dig_disp) {
case 0: P2= digi_val[dig_1]; dig_ctrl_1 = 1;
break;
case 1: P2= digi_val[dig_2]; dig_ctrl_2 = 1; break;
case 2: P2= digi_val[dig_3]; dig_ctrl_3 = 1; break;
case 3: P2= digi_val[dig_4]; dig_ctrl_4 = 1; break; } }
void main() { init(); while(1) { if(up==0&&down==1) { test++; num=test; dig_4=num%10;
//check if up up pin pin is pressed pressed
num=num/10; dig_3=num%10; num=num/10; dig_2=num%10; dig_1=num/10; if(test==9999) test=0; } if(up==1&&down==0) { test--; num=test; dig_4=num%10; num=num/10; dig_3=num%10; num=num/10; dig_2=num%10; dig_1=num/10; if(test==0) test=9999; } } }
//check if down pin is is pressed pressed
Uses:
Used to count the visitors of an auditorium, hall, offices, malls, sports etc.
Used as integral part of security System in high confidential areas.
Used in Parking Lot.
Used in Elevator to prevent the maximum limit of weight.
Advantages:
High precision and accuracy can be achieved through it.
Since it is bidirectional, it can count in both directions peoples entering and exiting the place.
Since it is compact it can be easily implemented anywhere.
It is also cost effective.
Conclusion: Thus the project entitled “Bidirectional Visitor Counter” helps to measure the visitor entering and exiting a particular passage or way. The circuit counts both entering and exiting visitors and displays the number of visitors present inside the hall. Visitor counting is not limited to the entry/exit point of a company but has a wide range of applications that provide information to management on the volume and flow of people throughout a location. The visitor helps to maximize the efficiency and effectiveness of employees, floor area and sales potential of an organization. The circuit may also be enhanced with a wide counting range of above three digits by modifying software section of the system. It can also be enhanced for long and accurate sensing range using a laser torch instead of IR transmission circuit. Thus the circuit can be used to monitor visitor flow in effective manner, where the visitors have to counted and controlled.
Bibliography:
The 8051 Microcontroller and Embedded Systems – Systems – Mazidi
Electronics for you. - www.electronics foru.com/ foru.com/
The Online 8051/8052 8051/8052 Microcontro Microcontroller ller Resource - www.8052 .com .com
Op amps and linear integrated circuits by Ramakant A Gayakwad
Morris Mano-Digital Mano-Digital and Computer Logic Design
Electronic Devices & Circuit Theory Boylestad, Nashelsky
Wikipedia - www.wikipedia.org
