8-31 8311 1 Regis Regis tratio n Side Shift Motor Fa Fault ult RAP Description Registration Side Shift Motor Failed to return to the Home Position.
Initial Action
Refer to BSD 8.7 (3 of 4) for 4) for the following procedure.
Check for any obstructions in the paper path.
Check the Registration Side Shift Motor assembly and gears for broken gear shaft or gears ( PL 2.3). 2.3 ).
Procedure Enter DC330 008-020 Regi Side Shift Motor . Motor . Select Start. Start . The Registration Side Shift Motor operates. Yes
No
Unanswered
Go to Flag11 on BSD 8.7 (3 of 4). 4) . check the harness and connectors for an open circuit. The harness and connectors are good. Yes
No
Unanswered
Repair the harness and connectors. CR3 (Green (Green LED) on th e SMA Driver D PWB is On. Yes
No
Unanswered
Check Fuse F5 on the Distribution 1 PWB ( PL 13.3). 13.3 ). Fuse F5 is good . Yes
No
Unanswered
Replace F5 ( PL 13.3). 13.3). +24 VDC VDC is measured betw een J583D J583D-7, -7, 8 and and GND on th e SMA Driver D PWB. Yes
No
Unanswered
Go to LVPS 2 +24 VDC Wirenet and LVPS 2 +24 RTN Wirenet check the harness and connectors between LVPS 2 and SMA Driver D PWB. Replace the SMA Driver D PWB ( PL 13.2). 13.2). +5 VDC is measured betw een J453 J453-B10, -B10, B11, B13 and B13 on the IO PWB. Yes
No
Unanswered
Troubleshoot the circuit between the IO PWB and SMA Driver D PWB. Replace the Registration Side Shift Motor ( PL 2.3). 2.3 ). Troubleshoot the circuit between the IO PWB and Registration Side Shift Motor. Disconnect J110 J110.. Enter DC330 008-182 Regi Side Shift Home Snr . Snr . +5 VDC is measured betw een J566 J566-2 -2 on the BGM Driver PWB and GND. Yes
No Unanswered +5 VDC is measured betw een J563 J563-5 -5 on the BGM Driv er PWB and GND. Yes
No Unanswered +5 VDC is measured betw een J461 J461-B14 -B14 on the IO PWB and GND. Yes
No
Unanswered
Replace the IO PWB ( PL 13.3). 13.3). Go to Flag20 on BSD 8.7 (3 of 4). 4) . Check the harness and connectors for an open circuit. If they are good, replace the Registration Side Shift Home Sensor ( PL 2.3). 2.3). Go to Flag19 on BSD 8.7 (3 of 4) and 4) and check the harness and connectors for an open circuit. If they are good, replace the BGM Driver PWB ( PL 9.1). 9.1 ). Reconnect J110 J110.. Less th an +1 VDC VDC is m easured between J566 J566-2 -2 on the BGM Driv er PWB and GND. Yes
No
Unanswered
Replace the Registration Side Shift Home Sensor ( PL 2.3). 2.3). If that does not correct the problem, replace the BGM Driver PWB ( PL 13.3). 13.3 ). Disconnect J 109. Enter DC330 008-181 Regi Side Shift Snr Snr .. +5 VDC is measured betw een J566 J566-5 -5 on the BGM Driver PWB and GND. Yes
No Unanswered +5 VDC is measured betw een J563 J563-4 -4 on the BGM Driv er PWB and GND. Yes
No
Unanswered
8-311 Registration Side Shift Motor Fault RAP
Page 2 of 2
+5 VDC is measured betw een J461-B14 on the IO PWB and GND. Yes
No
Unanswered
Replace the IO PWB ( PL 13.3). Go to Flag14 on BSD 8.7 (3 of 4). Check the harness and connectors for an open circuit. If they are good, replace the Registration Side Shift Sensor ( PL 2.2). Go to Flag13 on BSD 8.7 (3 of 4) and check the harness and connectors for an open circuit. If they are good, replace the BGM Driver PWB ( PL 9.1). Reconnect J 109. Less th an +1 VDC is measured between J566-5 on the BGM Driver PWB and GND. Yes
No
Unanswered
Replace the Registration Side Shift Sensor ( PL 2.2). If that does not correct the problem, replace the BGM Driver PWB ( PL 13.3). Perform the following:
Clean the Registration Side Shift Sensor ( PL 2.2) and Registration Side Shift Home Sensor ( PL 2.3).
Go to Flag13, Flag14, Flag19 and Flag20 on BSD 8.7 (3 of 4). check the harness and connectors for an open circuit. If they are good, replace the Registration Side Shift Sensor ( PL 2.2) and/or Registration Side Shift Home Sensor ( PL 2.3).
