Cross Head Removal for Man B&W

The reciprocating action of piston is converted into rotary motion for crankshaft by means of the cross head where the piston rod and connecting rod are attached on both sides.

A routine maintenance has to be performed on crosshead bearing as per maker’s instruction. Following procedure is to be followed when carrying out crosshead bearing removal of a MAN MC-C engine: 1) Inform company and take permission. 2) Take immobilization certificate from port. 3) Read the manual and have a toll box meeting with everyone involved in the job. Discuss the procedure. 4) Prepare important tools and spares to be used in this operation 5) A risk assessment of all personnel doing the operation to be prepared and documented 6) Shut main engine starting air 7) Engage turning gear to the main engine crankshaft 8) Open indicator cocks of all cylinders 9) Stop main engine lube oil pump after cooling down of engine 10) Open crank case doors of fore and aft unit 11) Open crank case doors of that unit in which maintenance is to be carried out. 12) Put blower and ventilate the crankcase thoroughly as it is an enclosed space.

13) Prepare enclosed space entry checklist. 14) After sufficient ventilation wearing proper PPE you can enter the C/C. 15) Turn the crank throw to 90° before BDC. 16) Check the bearing clearance by inserting feeler gauge b/w bearing cap and crosshead journal exactly next to the landing surface of the piston rod foot.

17) The wear limit for a cross head bearing shell is limited to 50% reduction of the oil wedge length (L).[ L=10mm] 18) Turn the crankshaft down enough to give access to nuts and screws on piston rod. 19) Mount two chain blocks on the top of the crankcase for suspending the piston rod. 20) Loosen and remove the locking wire and screws on the piston rod foot.

21) Mount the lifting eye bolt on each side of the piston rod foot. 22) Turn the crosshead to TDC. 23) Hook the chain blocks to the eye bolt on the piston rod foot. And turn the crosshead down so t hat piston is now suspended on the chain blocks. 24) Turn to BDC. 25) Mount the hydraulic jack on the crosshead bearing cap nut and loosen them. [pressure : 1500 -1650 bars] 26) Mount the lifting attachment on the head of t he connecting rod. 27) Suspend the two chain blocks from the lifting brackets in the athwart ship direction.

28) Mount the 2 eye bolts on the top of the cross head bear ing cap. 29) With the help of the two chain blocks lift the bearing cap. Take it out of the engine and place it on a wooden base. 30) To check the upper bearing shell, remove the locking screws and push the shell out. 31) Mount the chain blocks to the lifting brackets on the frame box wall.

32) Turn the crosshead up until the piston rod lands on the crosshead. Ensure that the guide ring in the crosshead fits correctly in the centre hole of t he piston rod. 33) Do not remove the chain blocks or the lifting eye bolts.

34) Turn the crosshead to TDC and attach t he chain blocks to the lifting arrangement and haul it tight. 35) Mount the four supports for the guide shoes on the crosshead guide. 36) Carefully and slowly turn the crankshaft towards to exhaust side and make sure the crosshead guide sits on the supports. 37) Turn the crank throw towards BD C slowly while following with the chain blocks, thus continuously supporting the connecting rod.

38) In case it is necessary to remove the lower bearing shell, tilt the connecting rod towards the door on the cam shaft side with means of chain blocks.

39) Dismount the locking screws and turn the bearing shell so far up that an eye bolt can be mounted. Lift the bearing shell out. Top clearance in crosshead bearing Max: 0.29mm Min: 0.17mm Video for Cross head bearing removal[vsw id="llij_8RgqDg" source="youtube" width="550" height="400" autoplay="no"] You may also like to read-Ways of starting and testing emergency gener ator Reference: Maintenance Manual MAN B&W MC-C engine Image Credits: Maintenance Manual MAN B&W MC-C engine patrix Related posts: Main Engine Liner Removal Procedure for S50MC-C Engine Procedure for Removing Main Bearing of MAN B&W MC-C Engine Chain Tightening Procedure for MAN B&W Engine Free Sample- Main Engine Bearing Report

Jack Bolts for Marine Engine and the Procedure for Tensioning

Do Like Us on Facebook

Follow Us on Twitter Top of Form 710848313

marineinsight

http://w w w .aw e

end_of_article

1

email

FREE SIGN UP FOR MORE INTERESTING ARTICLES Email:

Bottom of Form Facebook comments: Leave a comment! Click here to cancel reply » Top of Form Add your comment below, or trackback from your own site. You can also subscribe to these comments via RSS. Be nice. Keep it clean. Stay on topic. No spam. Name (required)

Mail (will not be published) (required) Website (optional) 9915

0

/tech/procedures

This is a Gravatar-enabled weblog. To get your own globally-recognized-avatar, please register at Gravatar. Post Comment

2b31480d5a

Sign up to our newsletter!

9915

Bottom of Form Top of Form 2028323541 email

marineinsight

http://w w w .aw e

personal_saf ety

1

Email:

Submit

Bottom of Form

Recent News Number of Pirate Attacks Sharply Decreased in 2011 Neptune Terminals Sets New Terminal Handling Record At 12.85 Million Metric Tonnes Simplifying Port Operation through Automated Balloon Cranes First True Hybrid System To Be Installed On Board An Offshore Supply Vessel Using BIM Technology to build the Panama Canal of the Future Dredging Corporation of India signs MOU with Ministry of Shipping for the year 2012 -13 Dredging

Wärtsilä Signs Long-Term Service Agreement W ith Prestige Cruise Holdings Popular Latest Comments

7 Reasons Deck Cadets and Junior Engineers are Not Getting JobsSeptember 5, 2011

Duties of a 4th Engineer on a ShipNovember 4, 2010

A Woman Chief Engineer from Brazil Describes Her Interest ing LifeMarch 14, 2011

How to Synchronize Generators on a Ship?October 18, 2010

Bunkering is Dangerous : Procedure for Bunkering Operation on a ShipOctober 19, 2010

The Very First Flotel in the World: Edda FidesMarch 16, 2012

How to Charge Refrigeration Plant on Ships?March 16, 2012

Cargo Ship Mont-Blanc and the Halifax Explosion: World’s Largest Man -made Accidental ExplosionMarch 15, 2012

10 Ways to Enhance the Security of a ShipMarch 15, 2012

How to Improve Energy Efficiency of Ships?March 13, 2012

ankush (DMET '08): Well said sir...

KABIR KHAN: THIS IS TRUE THAT MANY INSTITUTE ARE PROMISING 100...

Renjith: How do you remove excess charge in a reefer plant?...

datta rohakale: in gas charging in refer plant... after creatin...

Davis mwangi: Ma'am am v proud of you a really wanna be a marine... Top of Form 1634722164

marinenew s

email

Subscribe to Latest Maritime News Email:

Bottom of Form Random Posts

http://w w w .aw e

New s_-_Marine_

1

(refresh random posts) Latest Video Post Video : IMO Works to Make Ship Re cycling Safer and Environmentally Friendly Resources 23 Places to Find Maritime Jobs What is the Salary of Seafarers? Best Maritime Colleges in the United States Top 6 Books on Marine Auxiliary Machinery 23 Maritime Forums and Discussion Boards Shore Jobs for Seafarers Top 5 Books on Marine Boiler How to find Contacts in Maritime Companies? Most Commented 7 Reasons Deck Cadets and Junior Engineers are Not Getting Jobs Duties of a 4th Engineer on a Ship A Woman Chief Engineer from Brazil Describes Her Interesting Life How to Synchronize Generators on a Ship? Bunkering is Dangerous : Procedure for Bunkering Operation on a Ship About Us Contact Us Subscribe to Marine Insight Privacy Policy Follow us on Twitter Follow us on Facebook Forums

Jobs Directory Copyright © 2010 MarineInsight — All Rights Reserved

Read more: http://www.marineinsight.com/tech/proceduresmaintenance/procedure-for-cross-headbearing-removal-for-marine-engine-man-bw-s50mc-c/#ixzz1pPKXCCta