Chemical Milling, Chemical Blanking and Photochemical Blanking”

Chemical Milling, Chemical Blanking and Photochemical Blanking

Menu Home Exhibitions Metallurgy Courses Metallurgy Directory Metallurgy Books Metallurgy Vacancies Articles Alumni Submit a Site Submit an Article Submit a Vacancy Contac ontactt Us

Discounts on Science Discounts Magazines Ma gazines and Journals

12/05/11 13.57

Application of Chemical Milling, Chemical Blanking and Photochemical Blanking in Metal Working Industries By Dr Thoguluva Raghavan Vijayaram BE (Mechanical Engineering, Madurai Kamaraj University, India), ME (Metallurgical Engineering, Bharathiyar University, India), PhD (Mechanical Engineering, Universiti Putra Malaysia, Malaysia), Rector Grant Researcher in Metallurgy (Genoa University, Italy), Chartered Engineer (M123412(M123412-3, 3, IIE, Calcutta, India) MIIF, MISTE, MIIPE, MIE (Calcutta, India) Senior Lecturer in Manufacturing Engineering Engineering and Researcher in Metallurgy, Department of Manufacturing Process and System, Faculty of Manufacturing Engineering, UTeM, Universiti Universiti Teknikal Malaysia Melaka, Ayer Keroh, 75450 Melaka, Malaysia. E-mail: [email protected]

Uni in the USA The UK Guide to US Universities

Chemical Machining is a type of material removal process for the production of desired shapes and dimensions through selective or overall removal of material by controlled chemical attack with acids or alkalis often called as etchant solutions.

Ads by Google Google

Chemical Milling is one is one of the chemical chemical machining processes, sometimes called as Chemilling or Contour machining or etching and mainly used to produce shapes by selective or overall removal of metal parts from relatively large surface areas. The main purpose is to produce shallow cavities with complex profiles on plates, sheets, forgings, generally for the overall reduction of weight. This process has been used on a wide variety of metals metals with depths of metal removal as large as 12 mm. Chemical milling entails entails four important steps:

Chemical Industry Chemicall Product Chemica Products s Chemicall Safety Chemica Chemicall Companie Chemica Companies s

Products Men's Safe Safety ty Footwear Women's Safety Footwear Fo otwear

1. 2. 3. 4.

Cleaning. Masking. Etching. De-masking.

The stresses in the parts should be relieved in order to prevent warping after chemical milling. The surfaces are degreased and cleaned thoroughly to ensure both good adhesion of the masking masking material and uniform uniform material removal. removal. Then the masking material is is applied. Masking with tapes or paints (maskants) is a common practice, although elastomers (rubber and neoprene) and plastics (polyvinyl chloride, chloride, polyethylene, polyethylene, and polystyrene) are also used. The maskant material should not react with the chemical reagent. If required, the maskant that covers various regions that require etching etching is peeled off off by the scribe-and-peel scribe-and -peel technique. The exposed surfaces surfaces are machined chemically with etchants, such as sodium hydroxide (for aluminium), solutions of hydrochloric and nitric acids (steels), or iron chloride (for stainless steels). Temperature control and agitation (stirring) during chemical milling is important in order to obtain a uniform depth from the material removed. After machining, the parts should be washed thoroughly to prevent further reactions with or exposure to any etchant residues. The rest of the masking material is removed and the part is cleaned and inspected. The masking material is unaffected by the reagent but usually is dissolved by a different type of solvent. Additional finishing finishing operations may be performed on chemically milled parts. This sequence of operations can be repeated to produce stepped cavities and various contours. Schematic sketches of chemical milling process are shown in the Figure-1.

http://www.themetallurgist.co.uk/articles/chemical_milling_chemical_blanking_and_photochemical_blanking.shtml

Pagina 1 di 5


12/05/11 13.57

Key Performance Indicator How to select the right KPIs? Search in 5000+ KPIs by industry www.kpilibrary.com

Figure-1 Chemical Milling Process

Wet Benches Wet Chemical Process Equipment Clean, Etch, Strip and Plating www.waferprocess.com

Metallurgical Laboratory Custom Mechanical, Fatigue Testing ASTM & ISO Test Experience; A2L A. www.exova.com/Metal…

Metals Technology UKAS Approved Laboratory Metallurgical Services for Industry www.metalstechnolog…

Chemical milling is used in the aerospace industry to remove shallow layers of material from large aircraft components, missile skin panels, and extruded parts for airframes. Tank capacities for reagents are as large as 3.7 m X 15 m. This process is used to fabricate microelectronic devices and often is referred to as wet etching for these products. Some surface damage may result from chemical milling because of preferential etching and intergranular attack, which adversely affect surface properties. The chemical milling of welded and brazed structures may result in uneven material removal. The chemical milling of castings may result in uneven surfaces caused by porosity and non-uniformity of the material. With optimum time, temperature and solution control, accuracies of the range of plus or minus 0.01 mm can be achieved on relatively shallow depths of cut. The surface finish obtained may be around 5 microns. Aluminium alloys show better surface finish of the order of 1.6 microns. The metal removal rate on an aluminium component is reported to be about 140 cubic centimeters per minute. Chemical Blanking is similar to the blanking of sheet metals and it is applied to produce features, which penetrate through the thickness of the material, with the exception that the material is removed by chemical dissolution rather than by shearing. Typical applications for chemical blanking are the burr-free etching of printed-circuit boards, decorative panels, and thin sheet metal stampings, as well as the production of complex or small shapes. It is otherwise called as Chem-blanking, Photo forming, Photo fabrication, or Photo etching. In this process, the metal is totally removed from certain areas by chemical action. The process is used chiefly on the sheets and foils. This process can work almost any metal, however, it is not recommended for material thinner than 2 mm. A Schematic sketch of the chemical blanking process is shown in Figure-2.


Pagina 2 di 5


12/05/11 13.57

Figure-2 Chemical Blanking Process The work piece is cleaned, degreased and pickled by acid or alkalis. The cleaned metal is dried and photo resist material is applied to the work piece by dipping, whirl coating or spraying. It is then dried and cured. The technique of photography has been suitably employed to produce etchant resistant images in photo resist materials. This type of maskant is sensitive to light of a particular frequency, usually ultraviolet light, and not to room light. This surface is now exposed to the light through the negative, actually a photographic plate of the required design, just as in developing pictures. After exposure, the image is developed. The unexposed portions are dissolved out http://www.themetallurgist.co.uk/articles/chemical_milling_chemical_blanking_and_photochemical_blanking.shtml

Pagina 3 di 5


12/05/11 13.57

during the developing process exposing the bare metal. The treated metal is next put into a machine, which sprays it with a chemical etchant, or it may be dipped into the solution. The etching solution may be hydrofluoric acid (for titanium), or one of the several other chemicals. After 1 to 15 minute, the unwanted metal has been eaten away, and the finished part is ready for immediate rising to remove the etchant. Chemical blanking by using photo resist maskants can suitably make printed circuit boards and blanking of intricate designs. The advantages of this process are summarized below:

1. Very thin material (0.005 mm) can be suitably etched. 2. High accuracy of the order of plus or minus 0.015 mm can be maintained. 3. High production rate can be met by using automatic photographic technique. Photochemical Blanking is otherwise called as photo etching. It is a modification of chemical milling. Material is removed (usually from a flat thin sheet) by photographic techniques. Complex, burr-free shapes can be blanked on metals as thin as 0.0025 mm. Sometimes called photochemical machining and this process is also used for etching. The design of the part to be blanked is prepared at a magnification of up to 100 x. Then a photographic negative is made and reduced to the size of finished part. The reduced negative of the design is called artwork. The original (enlarged) drawing allows inherent design errors to be reduced by the amount of reduction (such as 100 x) for the final artwork image. The sheet blank is coated with a photosensitive material (photo resist) by dipping, spraying, spin casting, or roller coating and dried in an oven. This coating is called as emulsion. The negative is placed over the coated blank and exposed to ultraviolet light, which hardens the exposed areas. The blank is developed, which dissolves the unexposed areas. Then the blank is immersed into a bath of reagent (as in chemical milling) or sprayed with the reagent, which etches away the exposed areas. The masking material is removed, and the part is washed thoroughly to remove all chemical residues. Typical applications for photochemical blanking are fine screens, printed circuit boards, electric motor laminations, flat springs, and masks for color televisions. Some of the advantages are listed below.

1. Although skilled labor is required, tooling costs are low and the process can be automated. 2. This process is economical for medium to high production volume. 3. Photochemical blanking is capable of making very small parts where traditional blanking dies are difficult to produce. 4. The process is also effective for blanking fragile work pieces and materials. 5. The handling of chemical reagents requires precautions and special safety considerations to protect the workers against exposure to both liquid chemicals and volatile chemicals. 6. The disposal of chemical by-products from this process is a major drawback, although some by-products can be recycled. About the Author Dr.Thoguluva Raghavan Vijayaram, currently working as Senior Lecturer in the Faculty of Manufacturing Engineering at UTeM, Universiti Teknikal Malaysia Melaka, Malaysia. He hails from India and he has completed his PhD Research Degree in Mechanical Engineering (Metal Matrix Composites: Materials Engineering) from the Faculty of engineering, Universiti Putra Malaysia. He has published quality research papers in reputed International journals, National journals, International conference proceedings and in the Malaysian broadsheet. He has a wide range of work experience, both in academics and as well as in industry, consultancy, and teaching and especially in research and development work. His areas of expertise include: Metallurgical Engineering, Mechanical Engineering and Manufacturing Engineering and his special areas of research interests are in the field of advanced casting technology and techniques, composite materials and processing, powder metallurgy, Ferrous and NonFerrous foundry metallurgy, solidification science and technology, solidification processing of metals, alloys and composites, microgravity solidification, squeeze casting, die casting die design, heat treatment, Metallography, microstructure- property correlation ship, new materials and process development, aerospace engineering materials, computer simulation of casting solidification, FEM analysis and advanced


Pagina 4 di 5


12/05/11 13.57

engineering mathematics. Besides, he is a prominent writer and possesses wider experience in editing technical papers, theses and dissertations. Metallurgical Aspects of Powder Coating Technology Electrical Discharge Machining (EDM) of Metals and Alloys The Role of Electrochemical Machining (ECM) in Industrial Metallurgy Aerospace Industries Learn about aerospace industries AeroMat 2011 Conference and Expo www.asminternational.org/aeromat

New Product Launch Process Top Executives Give Best Practices & Strategic Insights. Free Download www.gogplus.com

Diamantane Supplies Low Cost Diamantane with High Purity. Ships Worldwide. Order Now! www.diamantane.info

REACH Your Partner of Choice for REACH Testing & Consultancy www.covance.com/reach

©The Metallurgist 2004 - 2010 www.themetallurgist.co.uk Disclaimer & Legal Link to Us Sitemap


Pagina 5 di 5

Chemical Milling, Chemical Blanking and Photochemical Blanking”

Recommend Documents