MINISTRY OF SCIENCE AND TECHNOLOGY
DEPARTMENT OF TECHNICAL AND VOCATIONAL EDUCATION
Sample Questions & Worked Out Examples for CE-04015 GEOTECHNICAL GEOTECHNICAL ENGINEERING
B.Tech. (Second Year)
Civil Engineering
MINISTRY OF SCIENCE AND TECHNOLOGY
MINISTRY OF SCIENCE AND TECHNOLOGY
DEPARTMENT OF TECHNICAL AND VOCATIONAL EDUCATION
CE-04015 GEOTECHNICAL ENGINEERING Sample Questions
B.Tech. (Second Year)
Civil Engineering
PART - I
1
1
CHAPTER ( 1 ) Soil and Rocks
1.* Define: (a) Effective size, (b) Uniformity Coefficient, (c) Coefficient of Gradation. 2.* The Atterberg limits of a soil are LL = 74, PL = 27 and the soil contains 43% by weight of clay. The water content of the soil is ω = 65.1%. Calculate the plasticity index 0f the soil. 3.* For a soil suppose that D 10 = 0.08mm, D 30 = 0.22mm, and D 60 = 0.41mm. Calculate the uniformity coefficient and the coefficient of gradation. 4.* A liquid limit test carried out on a sample of inorganic soil taken from below the water table gave the following results: Penetration (mm) 15.6 18.2 21.4 23.6 Moisture content ( % ) 34.6 40.8 48.2 53.4 A plastic limit test gave a value of 33%. Determine the liquid limit and plasticity index of this soil. 5.** Following are the results of a sieve analysis. U.S sieve no. 4 10 20 40 60 100 200 Pan
Mass of soil retained 28 42 48 128 221 86 40 24
( a ) Determine the percent finer than each sieve and plot a grain-size distribution curve. ( b ) Determine D 10, D30 and D60 from the grain-size distribution curve. ( c ) Calculate the uniformity uniformity coefficient, C u. ( d ) Calculate the coefficient of gradation, C c.
2 6.** Following are the results of a sieve analysis. Opening size (mm)
Mass of soil retained
2 6.** Following are the results of a sieve analysis. Opening size (mm) 4.76 2.00 1.19 0.59 0.42 0.25 0.149 0.074 Pan
Mass of soil retained 10 30 52 80 141 96 105 85 51
( a ) Determine the percent finer each sieve and plot a grain-size distribution curve. ( b ) Determine D 10, D30 and D60 from the grain-size distribution curve. ( c ) Calculate the uniformity coefficient, c u. ( d ) Calculate the coefficient of gradation, c c.
3 CHAPTER ( 2 ) Soil Composition
1.* Define:- Porosity, Degree of Saturation, Void Ratio and Water Content.
3 CHAPTER ( 2 ) Soil Composition
1.* Define:- Porosity, Degree of Saturation, Void Ratio and Water Content. 2.* A cylinder of undisturbed saturated soil is 38mm in diameter and 78mm long and its mass is 142 g. after oven drying its mass mass is 86 g. Calculate the water content and unit weight of of the soil. 3.* Calculate the dry unit weight, the saturated unit weight and the buoyant unit weight of a soil having a void ratio of 0.70 and a value of G s is 2.72. Calculate also the unit weight and water content at a degree of saturation of 75%. 4.* A soil specimen is 38mm in diameter and 76mm long and in its natural condition weights 168.0g. When dried completely in an oven the specimen weights 130.5g. The value of G s is 2.73. What is the degree of saturation of the specimen? 3
5.** A soil has a bulk density of 1.91 Mg/m and a water content of 9.5%. The value of G s is 2.70. Calculate the void ratio and degree of saturation of the soil. What would be the values of density and water content if the soil were fully saturated at the same void ratio? 6.** For a soil in natural state, given e = 0.8, ω = 24% and G s = 2.68. ( a ) Determine the moist unit weight, dry unit weight, and degree of saturation. ( b ) If the soil is made completely saturated by adding water, what would its moisture content be at the time? Also find the saturated unit weight. 7.** A laboratory test carried out on an undisturbed sample of soil weighing 1.74 kg and 3 having a volume of 1/1000 m determined the specific gravity of the soils to be 2.7 and the 3 dry density of the soil to be 1500kg/m . Calculate; ( a ) The void ratio and porosity. ( b ) The critical hydraulic gradient. ( c ) The critical hydraulic gradient. ( d ) The saturated and effective unit weight. ( e ) The degree of saturation of the soil. 8.** A sample of soil is prepared by mixing a quantity of dry soil (G s = 2.7) with 10.5% by weight of water. Find the weight of this wet mixture which will be required to produce, by static compaction, a cylindrical specimen 150mm diameter by 125mm deep with 5% air voids. 3
9.*** Soil has been compacted in an embankment at a bulk density of 2.15 Mg/m and a water content of 12%. The value of G s is 2.65. Calculate the dry density, void ratio, degree of saturation and air content. Would it be possible to compact the above soil at a water content 3 of 13.5% to a dry density of 2.00 Mg/ m ? 3
10.*** A sample of soil weighing 30.6 kg had a volume of 0.0183 m . When dried out in an oven its weight was reduced to 27.2 kg. The specific gravity of the solids was found to be 2.65. Determine the following: ( a ) Bulk density ( b ) Dry density ( c ) Percentage moisture content
4 ( d ) Void ratio ( e ) Porosity ( f ) Degree of saturation
4 ( d ) Void ratio ( e ) Porosity ( f ) Degree of saturation ( g ) Critical hydraulic gradient.
11.*** In order to measure the insitu density of a soil the following sand replacement test was carried out 4.56 kg of soil were extracted from a hole at the surface of the soil. The hold was then just filled with 3.54 kg of loose dry sand. ( a ) If the took 6.57 kg the same sand to 3 fill a container 0.0042 m in volume, determine the bulk density of the soil. ( b ) In a water content determination 24 g of the moist soil weighted 20g after drying in an oven at 15°c. If the specific gravity of the particles was 2.68, determine the water content, the dry density and the degree of saturation of the soil. 12.*** In a British standard compaction test a maximum dry density of 1.83 g/ml was produced. After compaction by field plants an undisturbed sample of the same soil, obtained by core cutter, weighted 2072g. The core cutter was 127mm long with a diameter of 102mm. Laboratory tests for water content and specific gravity yield a dry mass of 1806g and 2.67 respectively. Determine for the field compacted soil sample. ( a ) water content ( b ) bulk density ( c ) void ratio ( d ) air content ( e ) degree of saturation
5 CHAPTER ( 3 ) Classification of Soil
1.** The particle-size characteristics of a soil are given as follows:
5 CHAPTER ( 3 ) Classification of Soil
1.** The particle-size characteristics of a soil are given as follows: Sizes 0.425 0.033 0.018 0.010 0.0062 0.0035 0.0018 0.0010
% finer 100 90 80 70 60 50 40 35
Draw a particle-size distribution curve and determine the percentages of gravel, sand, silt, and clay, using AASHTO system.
6 CHAPTER ( 4 ) Flow of Water in Soil
1.* In a falling head permeability test the initial head of 1.00 m dropped to 0.35 m in 3h, the
6 CHAPTER ( 4 ) Flow of Water in Soil
1.* In a falling head permeability test the initial head of 1.00 m dropped to 0.35 m in 3h, the diameter of the standpipe being 5mm. The soil specimen was 200mm long by 100mm in diameter. Calculate the coefficient of permeability of the soil. 2.* For a constant head permeability tests, the following values are given. L = 300mm A = specimen area = 32 cm 2 k = 0.0244 cm/sec The head differences was slowly changed in steps to 800, 700, 600, 500and 400 mm. 3 Calculate and plot the rate of flow, q, through the specimen, in cm /sec, against the head different. 3.** A deposit of soil is 16m deep and overlies an impermeable stratum: the coefficient of -6 permeability is 10 m/s. A sheet pile wall is driven to a depth of 12.00m in the deposit. The difference in water level between the two sides of piling is 4.00m. Draw the flow net and determine the quantity of seepage under the piling. 4.** The section through part of a cofferdam is shown in Figure, the coefficient of -6 permeability of the soil being 2.0 x 10 m/s. Draw the flow net and determined the quantity of seepage.
3
5.** Refer to Figure. Fine the flow rate in m /sec/m length (at right angle to the cross section shown) through the permeable soil layer. Given: H = 4m, H 1=2m, h = 3.1m, L = 30m, α = 14°, k = 0.05 cm/sec.
7
7
6.** For the flow net drawn in Figure. Calculate the up lift force at the base of the weir per foot length (measured along the axis) of the structure.
7.** The section through part of a sheet pile wall is shown in the Figure. The saturated unit 3 -5 weight of the soil being 19 kN/m and coefficient of permeability is 2.5x10 m/s. The length of the sheet pile wall is 30m. Determine the quantity of seepage per day and pore water pressure at end of the sheet pile wall.
8
8.*** A homogeneous isotropic earth dam section is detailed in figure, the coefficients of -8 permeability is 4.5 x 10 . Draw the first flow line and determine the quantity of seepage
8
8.*** A homogeneous isotropic earth dam section is detailed in figure, the coefficients of -8 permeability is 4.5 x 10 . Draw the first flow line and determine the quantity of seepage through the dam.
9.*** An embankment dam is shown in section in Figure, the coefficient of permeability in -6 -6 the horizontal and vertical directions being 7.5 x 10 and 2.7 x 10 m/s respectively. Construct the top flow line and determine the quantity of seepage through the dam.
10.*** The flow net for seepage under the proposed dam shown in the figure below is 100m long and 25.5m wide. wide. To decrease the seepage loss, sheet piles were driven in at the the heel and at the toe of the dam t o a depth of 6.3. The coefficient of permeability of the soil is 0.05 cm/s. 2 The saturated unit weight of the soil is 20 kN/m . ( a ) Find the quantity of water that will be los t per day per seepage. ( b ) Plot the distribution of uplift pressure on the base of the dam.
9 CHAPTER ( 5 )Effective Stress 3
1.* The bed of a river 5 m deep consists of saturated unit weight 19.5 kN/m . Calculate the
9 CHAPTER ( 5 )Effective Stress 3
1.* The bed of a river 5 m deep consists of saturated unit weight 19.5 kN/m . Calculate the effective vertical stress 5 m below the surface of the sand. 2.** A layer of clay 4 m thick lies between two layers of sand each 4 m thick, the top of the upper layer of sand being ground level. The water table is 2 m below ground level but the lower layer of sand is under artesian pressure, the piezometric surface being 4 m above ground level. The saturated unit weight of the clay is 20 kN/m 3 and that of the sand 19 kN/m 3 3 : above the water table the unit weight of the sand is 16.5 kN/m . Calculate the effective vertical stresses at the top and bottom of the clay layer. 3.** In a deposit of fine sand the water table is 3.5 m below the surface but sand to a height of 1.0 m above the water is saturated by capillary water: above this height the sand may be 3 assumed to be dry. The saturated and dry unit weights, respectively, are 20 kN/m and 16 3 kN/m . Calculate the effective vertical stress in the sand 8 m below the s urface. /
4.** Refer to figure. Calculate σ, u and σ at A, B, C and D for the following cases, and plot the variations with depth. 3 For soil layer I, H1 = 2 ft, γd = 115 lb/ft 3 II, H2 = 4 ft, γsat = 118 lb/ft 3 III, H3 = 6 ft, γsat = 130 lb/ft
/
5.** Refer to Figure. For the given data, calculate and plot σ, u and σ with depth. Given: H1 = 6 ft, H 2 = 4 ft, H 3 = 9 ft Degree of saturation in capillary rise zone, s (%) = 50%
10
10
6.*** Refer to the soil profile shown in Figure. / ( a ) Calculate and plot the variation of σ, u and σ with depth. ( b ) If the water table rises to the top of the ground surface, what is the change in the effective stresses at the bottom of the clay layer? ( c ) How many feet must the ground water table rises to decrease the effective stress by 300 2 lb/ ft at the bottom of the clay layer?
7.*** A layer of sand extends from ground level to a depth of 9 m and overlies a layer of clay, of very low permeability, 6m thick. The water table is 6m below the surface of the sand. 3 3 The saturated unit weight of the sand is 19 kN/m and that of the clay 20 kN/m : the unit weight of the sand above the water table is 16 kN/m 3 . Over a short period of time the water rises by 3m and is expected to remain permanently at this new level. Determine the effective vertical stress at depth of 8m and 12m below ground level ( a ) immediately after the rise of the water table, ( b ) several years after the rise of the water table. 8.*** A stratum of sand 2.4m thick overlies a stratum of saturated clay 3.0m thick. The water table being 0.9m below the ground surface. surface. The saturated unit weight of the clay and sand 3 3 are 18.5 kN/m and 20.6kN/m respectively. Above the water table the unit weight of the 3 sand is 17.4 kN/m .
11 ( a ) Calculate total vertical stress and effective vertical stress at against depth. ( b ) If sand to a height of 0.9m above the water table is saturated with capillary water, how are the above stress affected? ( c ) If the water table rise to the ground surface, what is the effect on the stresses?
11 ( a ) Calculate total vertical stress and effective vertical stress at against depth. ( b ) If sand to a height of 0.9m above the water table is saturated with capillary water, how are the above stress affected? ( c ) If the water table rise to the ground surface, what is the effect on the stresses? 9.*** The soil stratum is shown in Figure. Plot the total stress, pore water pressure and effective stress with depth. ( a ) Assume that zone of capillary rise is s = 100%. ( b ) If water table rise to 2m above the old water table.
12 CHAPTER ( 6 ) Stresses in Soil Mass
1.* For the stressed soil element shown in Figure, determine ( a ) Major principal stress
12 CHAPTER ( 6 ) Stresses in Soil Mass
1.* For the stressed soil element shown in Figure, determine ( a ) Major principal stress ( b ) Minor principal stress ( c ) Normal and shear stress on the plain AE.
2.* Using the equation, for the soil mass is shown in Figure. Determine the following, ( a ) Maximum and minimum principal stresses. ( b ) Normal and shear stress on the plain AB.
3.* Using the principal of Mohr’s circles, for the soil element shown in Figure, determine the following. ( a ) Maximum and minimum principal stresses. ( b ) Normal and shear stresses on the plain AB.
13 4.* Calculate the vertical stress in a soil mass of 5m vertically below a point load of 5000 kN acting near the surface. Plot the variation of vertical stress with radial distance (up to 10m) at a depth of 5m.
13 4.* Calculate the vertical stress in a soil mass of 5m vertically below a point load of 5000 kN acting near the surface. Plot the variation of vertical stress with radial distance (up to 10m) at a depth of 5m. 5.* Three point loads, 10,000 kN, 7500 kN and 9000 kN, act in line 5m apart near the surface of a soil mass. Calculate the vertical stress at a depth of 4m vertically below the center ( 7500kN ) load. 6.** Determine the vertical stress at a depth of 3m below the center of a shallow foundation 2 2m x 2m carrying a uniform pressure of 250 kN/m . Plot the variation of vertical stress with depth ( up to 10m ) below the center of the foundation. 2
7.** A shallow foundation 25m x 18m carries a uniform pressure of 175 kN/m . Determine the vertical stress at a point 12m below the mid-point of one of the longer sides by using influence factors. 8.** Consider a point load p = 10000 lb. Plot the variation of the vertical stress increase, with depth causes by the point load below the ground surface with x = 3 ft and y = 4 ft. z is consider up to 20 ft. 9.** Consider a circularly loaded flexible area on the ground surface. Given that the radius of 2 the circular area R = 6 ft and that the uniformly distributed load q = 3500 lb / ft . Calculate the vertical stress increase, ∆ p at points 1, 2, 3, 6, 9 and 12 ft below the ground surface ( immediately below the center of the circular area.)
3
10.** A strip footing 2m wide carries a uniform pressure of 250 kN/m on the surface of a deposit of the sand. The water table is at the surface. The saturated unit weight of the sand is 3 20 kN/m and K o = 0.40. Determine the effective vertical and horizontal stresses at a point 3m below the center of the footing before and after the application of the pressure. 11.*** Refer to Figure. Given q 1= 750 lb / ft, x 1 = 8 ft, x 2 = 4 ft and z = 3 ft. If the vertical 2 stress increase at point A due to the loading is 35 l b / ft , determine the magnitude of q 2.
14
14
12.*** Point load of magnitude 2000, 4000 and 6000 lb act at A, B and C respectively shown in Figure. Determine the increase in vertical stress at a point of 10 ft below point D.
13.*** The plan of a flexible rectangular area is shown in Figure. The uniformly distributed 2 load on the flexible area q is 1800 lb/ft . Determine the vertical stress increase, ∆ p, at a depth of z = 5 ft below. ( a ) Point A, ( b ) Point Point B, ( c ) Point C
15 14.***Refer to previous problem. Calculate and plot the stress increase at z = 0, 5, 10, 15, 20 and 25 ft below the center of the loaded area.
15 14.***Refer to previous problem. Calculate and plot the stress increase at z = 0, 5, 10, 15, 20 and 25 ft below the center of the loaded area. 2
15.*** A rectangular foundation 6m x 3m carries a uniform pressure of 300 kN/m near the surface of a soil mass. Determine the vertical stress at a depth of 3m below a point ( A ) on the center line 1.5m outside a long edge of the foundation, using influence factors.
PART - II
