Caterpillar C27-C32.pdf

RENR9716-02 September 2008

Disassembly and Assembly C27 and C32 Generator Sets Engines DWB1-Up (Generator Set) SXC1-Up (Generator Set) MED1-Up (Power Module) WDR1-Up (Generator Set)

SAFETY.CAT.COM

i01658146

Important Safety Information Most accidents that involve product operation, maintenance and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills and tools to perform these functions properly. Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result in injury or death. Do not operate or perform any lubrication, maintenance or repair on this product, until you have read and understood the operation, lubrication, maintenance and repair information. Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. The hazards are identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as “DANGER”, “WARNING” or “CAUTION”. The Safety Alert “WARNING” label is shown below.

The meaning of this safety alert symbol is as follows: Attention! Become Alert! Your Safety is Involved. The message that appears under the warning explains the hazard and can be either written or pictorially presented. Operations that may cause product damage are identified by “NOTICE” labels on the product and in this publication. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are, therefore, not all inclusive. If a tool, procedure, work method or operating technique that is not specifically recommended by Caterpillar is used, you must satisfy yourself that it is safe for you and for others. You should also ensure that the product will not be damaged or be made unsafe by the operation, lubrication, maintenance or repair procedures that you choose. The information, specifications, and illustrations in this publication are on the basis of information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job. Caterpillar dealers have the most current information available.

When replacement parts are required for this product Caterpillar recommends using Caterpillar replacement parts or parts with equivalent specifications including, but not limited to, physical dimensions, type, strength and material. Failure to heed this warning can lead to premature failures, product damage, personal injury or death.

RENR9716-02

Table of Contents Disassembly and Assembly Section Engine - Remove ................................................... 4 Engine - Install ....................................................... 6 Fuel Priming Pump - Remove and Install .............. 9 Fuel Filter Base - Remove ................................... 10 Fuel Filter Base - Install ....................................... 10 Fuel Filter and Water Separator - Remove and Install .................................................................... 11 Fuel Transfer Pump - Remove .............................. 12 Fuel Transfer Pump - Install .................................. 12 Electronic Unit Injector - Remove ......................... 13 Electronic Unit Injector - Install ............................. 14 Electronic Unit Injector Sleeve - Remove ............. 15 Electronic Unit Injector Sleeve - Install ................. 16 Turbocharger - Remove ........................................ 17 Turbocharger - Disassemble ................................ 17 Turbocharger - Assemble .................................... 18 Turbocharger - Install ............................................ 18 Exhaust Manifold - Remove and Install ............... 19 Inlet and Exhaust Valve Springs - Remove and Install ................................................................... 20 Inlet and Exhaust Valves - Remove and Install .... 22 Inlet and Exhaust Valve Guides - Remove and Install ................................................................... 23 Inlet and Exhaust Valve Seat Inserts - Remove and Install ................................................................... 24 Engine Oil Filter Base - Remove .......................... 25 Engine Oil Filter Base - Disassemble ................... 26 Engine Oil Filter Base - Assemble ........................ 26 Engine Oil Filter Base - Install .............................. 27 Engine Oil Cooler - Remove ................................. 27 Engine Oil Cooler - Install ..................................... 28 Engine Oil Pump - Remove .................................. 28 Engine Oil Pump - Disassemble ........................... 29 Engine Oil Pump - Assemble ................................ 29 Engine Oil Pump - Install ...................................... 30 Water Pump - Remove ......................................... 31 Water Pump - Disassemble ................................. 31 Water Pump - Assemble ...................................... 32 Water Pump - Install ............................................. 33 Water Temperature Regulator Housing - Remove and Install .................................................................. 33 Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Remove ................................................ 35 Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Install .................................................... 36 Aftercooler - Remove ........................................... 38 Aftercooler - Install ............................................... 40 Radiator Core - Remove ...................................... 42 Radiator Core - Install .......................................... 44 Engine Support (Front) - Remove and Install ....... 45 Gear Group (Rear) - Remove ............................... 46 Gear Group (Rear) - Install ................................... 48 Flywheel - Remove and Install ............................. 49 Crankshaft Rear Seal - Remove ........................... 50 Crankshaft Rear Seal - Install ............................... 50 Flywheel Housing - Remove and Install .............. 51

3 Table of Contents

Vibration Damper and Pulley - Remove and Install ............................................................................. 53 Crankshaft Front Seal - Remove .......................... 54 Crankshaft Front Seal - Install .............................. 55 Gear Group (Front) - Remove .............................. 55 Gear Group (Front) - Install .................................. 56 Housing (Front) - Remove .................................... 57 Housing (Front) - Install ........................................ 58 Housing (Rear) - Remove ..................................... 60 Housing (Rear) - Install ......................................... 60 Valve Mechanism Cover - Remove and Install ..... 62 Valve Mechanism Cover Base - Remove and Install ................................................................... 62 Rocker Arm and Shaft - Remove .......................... 63 Rocker Arm - Disassemble ................................... 64 Rocker Arm - Assemble ........................................ 64 Rocker Arm and Shaft - Install .............................. 65 Cylinder Head - Remove ...................................... 66 Cylinder Head - Install .......................................... 68 Camshaft - Remove .............................................. 71 Camshaft - Install .................................................. 73 Camshaft Bearings - Remove ............................... 76 Camshaft Bearings - Install ................................... 76 Engine Oil Pan - Remove and Install ................... 78 Cylinder Liner - Remove ....................................... 79 Cylinder Liner - Install ........................................... 79 Piston Cooling Jets - Remove and Install ............. 80 Pistons and Connecting Rods - Remove .............. 81 Pistons and Connecting Rods - Disassemble ....... 82 Pistons and Connecting Rods - Assemble ........... 82 Pistons and Connecting Rods - Install .................. 83 Connecting Rod Bearings - Remove .................... 84 Connecting Rod Bearings - Install ........................ 85 Crankshaft Main Bearings - Remove .................... 86 Crankshaft Main Bearings - Install ........................ 87 Crankshaft - Remove ............................................ 88 Crankshaft - Install ................................................ 90 Bearing Clearance - Check ................................... 92 Atmospheric Pressure Sensor - Remove and Install ................................................................... 93 Camshaft Position Sensor - Remove and Install .. 93 Crankshaft Position Sensor - Remove and Install .. 94 Coolant Temperature Sensor - Remove and Install ................................................................... 95 Engine Oil Pressure Sensor - Remove and Install ............................................................................. 96 Fuel Pressure Sensor - Remove and Install ......... 97 Fuel Temperature Sensor - Remove and Install ... 97 Turbocharger Outlet Pressure Sensor - Remove and Install ................................................................... 98 Inlet Air Temperature Sensor - Remove and Install ................................................................... 99 Belt Guard - Remove and Install ........................... 99 Fan Guard - Remove and Install ........................ 100 Fan - Remove and Install ................................... 101 Fan Drive - Remove and Install ......................... 102 Electronic Control Module - Remove and Install .. 103 Alternator - Remove and Install ......................... 104 Electric Starting Motor - Remove and Install ..... 105

Index Section Index ................................................................... 106

4 Disassembly and Assembly Section

RENR9716-02

Disassembly and Assembly Section i02747487

Engine - Remove SMCS Code: 1000-011

Removal Procedure Table 1

Required Tools

Illustration 2

Tool

Part Number

A

138-7573

Link Bracket

2

B

238-9586

Engine Turning Tool

1

C

1U-9200

Lever Puller Hoist

1

D

189-0411

Shackle As

2

E

6V-6146

Load Leveling Beam

1

Part Description

Qty

g01291160

2. Disconnect harness assembly (6).

Start By: a. Remove the cooling package. Refer to Disassembly and Assembly, “Cooling System Package (Radiator, Aftercooler, Fuel Cooler) Remove”. Illustration 3

g01291161

3. Disconnect hose assemblies (7), (8), and (9).

Illustration 1

g01291159

1. Disconnect hose assembly (1). Disconnect cable assembly (2). Disconnect harness assemblies (3). Disconnect cable assembly (4). Disconnect harness assemblies (5).

Illustration 4

4. Disconnect clamp (10).

g01291162

RENR9716-02


7. Disconnect clamp (15).

Illustration 8

g01291225

8. Remove bolts (16). Remove guard (17).

Illustration 5

g01291179

5. Remove bolts (11). Remove bolts (12). Repeat for the opposite side. Disconnect tube assembly (13). Repeat for the opposite side.

Illustration 9

g01291227

9. Remove bolts (18). Remove guard (19).

Illustration 6

g01291183

6. Attach Tooling (A) and a suitable lifting device onto exhaust elbow (14). The weight of exhaust elbow (14) is approximately 34 kg (75 lb). Remove exhaust elbow (14).

Illustration 10

10. Disconnect hose (20).

Illustration 7

g01291186

g01291228


Illustration 11

RENR9716-02

g01291232

g01291246

Illustration 14

13. Attach Tooling (D) onto engine (24). Attach Tooling (E) and a suitable lifting device onto Tooling (D). The weight of engine (24) is approximately 3527 kg (7775 lb).

Illustration 12

g01291243

11. Install Tooling (B). Use Tooling (B) in order to rotate the engine. Rotate the engine in order to gain access to bolts (22). Remove bolts (22). Remove bolts (21).

g01291247

Illustration 15

14. Remove mounting bolts (25). Remove engine (24) from the generator. i02747534

Engine - Install SMCS Code: 1000-012

Installation Procedure Table 2 Illustration 13

Required Tools

g01376223

12. Use Tooling (C) in order to support generator rotor (23).

Tool

Part Number

A

138-7573

Link Bracket

2

B

238-9586

Engine Turning Tool

1

C

1U-9200

Lever Puller Hoist

1

D

189-0411

Shackle As

2

E

6V-6146

Load Leveling Beam

1

Part Description

Qty

RENR9716-02

Illustration 16


g01291246

1. Attach Tooling (D) onto engine (24). Attach Tooling (E) and a suitable lifting device onto Tooling (D). The weight of engine (24) is approximately 3527 kg (7775 lb). Install engine (24).

Illustration 19

3. Install bolts (21). Use Tooling (B) in order to rotate the engine. Install bolts (22).

Illustration 20 Illustration 17

g01291247

g01291232

g01291245

4. Remove Tooling (C).

2. Install mounting bolts (25).


g01291243

5. Connect hose (20).

g01291228


Illustration 22

RENR9716-02

g01291227

6. Install guard (19). Install bolts (18).

Illustration 23

Illustration 25

g01291183

9. Attach Tooling (A) and a suitable lifting device onto exhaust elbow (14). The weight of exhaust elbow (14) is approximately 34 kg (75 lb). Install exhaust elbow (14).

g01291225

7. Install guard (17). Install bolts (16).

Illustration 26

g01291179

10. Connect tube assembly (13). Install bolts (12). Repeat for the opposite side. Install bolts (11).

Illustration 24

g01291186

8. Connect clamp (15).

Illustration 27

g01291162

RENR9716-02


End By:

11. Connect clamp (10).

a. Install the cooling package. Refer to Disassembly and Assembly, “Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Install”. i02580978

Fuel Priming Pump - Remove and Install SMCS Code: 1258-010

Removal Procedure Illustration 28

g01291161

12. Connect hose assemblies (7), (8), and (9).

NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates.

Illustration 29

g01291160

13. Connect harness assembly (6).

Illustration 30

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

g01291159

14. Connect harness assemblies (5). Connect cable assembly (4). Connect harness assemblies (3). Connect cable assembly (2). Connect hose assembly (1).

Illustration 31

g01292755

1. Remove bolts (1). 2. Remove fuel priming pump (2) and the gasket.


RENR9716-02

Installation Procedure

1. Turn the fuel supply to the OFF position.

g01292755

Illustration 32

1. Position the gasket and fuel priming pump (2) on the fuel filter base. 2. Install bolts (1). Illustration 33

g01292764

i02580993

Fuel Filter Base - Remove

2. Use Tooling (A) to remove fuel filter (6) from fuel filter base (5).

SMCS Code: 1262-011

3. Disconnect harness assemblies (4).

Removal Procedure

4. Disconnect hose assembly (1) and hose assembly (2).

Table 3

5. Remove bolts (3) and fuel filter base (5).

Required Tools Tool

Part Number

A

185-3630

Part Description Strap Wrench

Qty 1

NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

i02581008

Fuel Filter Base - Install SMCS Code: 1262-012

Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

RENR9716-02


NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Turn the fuel supply to the OFF position.

g01292764

Illustration 34

1. Position fuel filter base (5) on the engine. Install bolts (3). 2. Connect hose assembly (1) and hose assembly (2). 3. Connect harness assemblies (4). 4. Install fuel filter (6) on fuel filter base (5). 5. Turn the fuel supply to the ON position.

Illustration 35 i02581074

Fuel Filter and Water Separator - Remove and Install

NOTICE Keep all parts clean from contaminants.

Table 4

Required Tools

A

185-3630

Part Description Strap Wrench As

3. Disconnect hose assemblies (2) and (3).


Removal Procedure

Part Number

2. Use Tooling (A) to remove the fuel filter and water separator (5) from base assembly (4).

4. Remove bolts (1) and base assembly (4).

SMCS Code: 1261-010; 1263-010

Tool

g01292832

Qty 1


Contaminants may cause rapid wear and shortened component life.


Illustration 36

RENR9716-02

g01292832

1. Position base assembly (4) on the cylinder block and install bolts (1). 2. Connect hose assemblies (2) and (3). 3. Install a new fuel filter and water separator (5) on base assembly (4). 4. Turn the fuel supply to the ON position.

Illustration 37

2. Disconnect hose assemblies (3). 3. Remove bolts (2).

i02285574

Fuel Transfer Pump - Remove

4. Remove fuel transfer pump (1) and the O-ring seal.

SMCS Code: 1256-011

Removal Procedure NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Turn the fuel supply to the “OFF” position.

g01143748

i02287501

Fuel Transfer Pump - Install SMCS Code: 1256-012


RENR9716-02


Illustration 39

g01114892

1. Disconnect harness assembly (1). 2. Remove bridge assemblies (3). g01143748

Illustration 38

1. Install the O-ring seal on fuel transfer pump (1). Lubricate the O-ring seal with clean engine oil. 2. Position fuel transfer pump (1) on the engine. Install bolts (2).

NOTICE If the injector hold down bolt is loose during the removal procedure, inspect the injector bore for wear and debris. Replace the clamp and spacer. 3. Remove bolt (4), spacer (5), and clamp (6). 4. Place an identification mark on electronic unit injectors (2) for installation purposes. Each electronic unit injector must be reinstalled in the original location in the cylinder head.

3. Connect hose assemblies (3). 4. Turn the fuel supply to the “ON” position. i02208070

Electronic Unit Injector Remove SMCS Code: 1290-011


Required Tools Tool

Part Number

A

5F-4764

Part Description Pry Bar

Qty 1

Illustration 40

g01073439

Start By:

5. Use Tooling (A) to pry beneath the base and free electronic unit injector (2).

a. Remove the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly, “Rocker Arm and Shaft - Remove”.

6. Remove electronic unit injector (2) from the cylinder head.



RENR9716-02

i03143340

Electronic Unit Injector - Install SMCS Code: 1290-012

Installation Procedure Table 6

Required Tools Tool

Part Number

B

8T-2998

Lubricant

1

1U-5718

Vacuum Pump

1

169-7372

Fluid Sampling Bottle

1

4C-4057

Tube 7.9 mm (0.31 inch) OD

1

D

4C-5552

Large Bore Brush

1

E

4C-6774

Vacuum Gun Kit

1

F

8T-7765

Surface Reconditioning Pad

1

C

Part Description

Qty

Illustration 41

g01114892

Illustration 42

g01135876

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Use Tooling (C) to remove the fuel and oil from the cylinder. Evacuate as much fuel and oil as possible from the cylinder before installing the electronic unit injector. Several evacuations may be necessary. 2. Use Tooling (D) to clean the carbon deposit from the inside of the electronic unit injector sleeve. Tooling (E) is available to clean loose material from the bore of the electronic unit injector sleeve and the cylinder.

5. When you install a new injector the E-Trim value must be programmed into the engine control module. The injector confirmation code may need to be programmed into the engine control module. E-Trim Value (X) is a twelve digit alphanumeric code that is supplied with the data sheet that comes with the new injectors. Injector Confirmation Code (Y) is a four digit numeric code. Both of the codes are located on the top of electronic unit injector (2). Use the following menu to program the E-Trim value.

3. Use Tooling (F) to clean the carbon from the seat area that is inside of the electronic unit injector sleeve.

• ECM Summary Screen

4. Install the O-ring seals on the electronic unit injector. Lubricate the top two O-ring seals with a 50/50 mixture of clean engine oil and Tooling (B).

• Calibration

• Service Menu

• Injector Code Calibration

RENR9716-02


NOTICE When an electronic unit injector is replaced, the new electronic injector code must be programmed into the engine’s personality module software by using the calibration menu on the Electronic Service Tool. If the new electronic injector code is not entered, the characteristics of the previous electronic unit injector is assumed. If it is not possible to immediately reprogram the electronic injector code into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance.

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

6. Position electronic unit injector (2) in the cylinder head. 7. Install spacer (5), clamp (6), and bolt (4). Tighten the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft). 8. Install bridge assemblies (3). 9. Connect harness assembly (1). Tighten the nuts to a torque of 2.5 ± 0.25 N·m (22 ± 2 lb in). End By: a. Install the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly, “Rocker Arm and Shaft - Install”.

Illustration 43

g01043124

2. Install Tooling (A) in electronic unit injector sleeve (1). 3. Tighten the nut on Tooling (A) until the electronic unit injector sleeve is pulled free of the cylinder head.

i02300212

Electronic Unit Injector Sleeve - Remove SMCS Code: 1713-011


Required Tools Tool

Part Number

A

9U-6891

Part Description

Qty

Injector Tool Group

Start By: a. Remove the electronic unit injectors. Refer to Disassembly and Assembly, “Electronic Unit Injector - Remove”.

1

Illustration 44

g01073635

4. Remove O-ring seals (2) and O-ring seal (3) from electronic unit injector sleeve (1).


RENR9716-02

i02287628

Electronic Unit Injector Sleeve - Install

Note: Do not apply Tooling (C) to the cylinder head surfaces. Apply Tooling (C) on the electronic unit injector sleeve only. 4. Lubricate O-ring seals (2) with clean engine oil.

SMCS Code: 1713-012


Required Tools Tool

Part Number

A

9U-6891

Injector Tool Group

1

9U-6862

Tapered Brush

1

9U-6863

Small Bore Brush

1

9U-7244

End Brush

1

9U-7237

Brush Extension

1

4C-5552

Large Bore Brush

1

4C-9507

Retaining Compound

1

B

C

Part Description

Qty

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve. NOTICE Ensure that the electronic unit injector sleeve and the cylinder head bore are completely free of oil, dirt, and sealant debris.

Illustration 46

g01099549

5. Install electronic unit injector sleeve (1) on Tooling (A). Position the electronic unit injector sleeve in the cylinder head. Use care not to damage the O-ring seals on the electronic unit injector sleeve. Use Tooling (A) and a hammer to install the electronic unit injector sleeve in the cylinder head. NOTICE Ensure that the electronic unit injector sleeve is properly seated in the cylinder head. The Tooling will "RING" when the electronic unit injector sleeve is fully seated in the bore of the cylinder head. 6. Remove Tooling (A). Remove excess Tooling (C). 7. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”. End By: a. Install the electronic unit injectors. Refer to Disassembly and Assembly, “Electronic Unit Injector - Install”.

Illustration 45

g01043165

2. Install new O-ring seals (2) and O-ring seal (3) on electronic unit injector sleeve (1). 3. Apply Tooling (C) to the contact surface of electronic unit injector sleeve (1) on the surface that is Marked “X”.

RENR9716-02


i02287744

Turbocharger - Remove SMCS Code: 1052-011

Removal Procedure NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Illustration 48

g01148173

Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products.

2. Remove tube assembly (2).

Dispose of all fluids according to local regulations and mandates.

4. Attach a suitable lifting device to turbocharger (5). The weight of turbocharger (5) is approximately 45 kg (100 lb).


3. Disconnect tube assemblies (1) and tube assembly (4).

5. Remove nuts (3). Remove turbocharger (5) and the gasket.

Contaminants may cause rapid wear and shortened component life. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

i02287870

Turbocharger - Disassemble SMCS Code: 1052-015

Disassembly Procedure Start By: a. Remove the turbocharger. Refer to Disassembly and Assembly, “Turbocharger - Remove”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 47

g01145002


RENR9716-02

1. Position compressor housing (1) and turbine housing (5) on turbocharger cartridge (3). Note: Ensure that the mating surfaces are flush. 2. Tighten the nuts on V-band clamp (2) to a torque of 14 ± 1 N·m (10 ± 1 lb ft). Use a soft hammer to lightly hit around the diameter of the band clamp. Tighten the nuts again to a torque of 14 ± 1 N·m (10 ± 1 lb ft).

Illustration 49

g01145263

3. Tighten the nuts on V-band clamp (4) to a torque of 14 ± 1 N·m (10 ± 1 lb ft). Use a soft hammer to lightly hit around the diameter of the band clamp. Tighten the nuts again to a torque of 14 ± 1 N·m (10 ± 1 lb ft).

1. Loosen V-band clamp (2) and V-band clamp (4).

4. Ensure that the impeller spins freely.

2. Separate compressor housing (1) from turbocharger cartridge (3).

End By:

3. Separate turbine housing (5) from turbocharger cartridge (3). i02451256

Turbocharger - Assemble

a. Install the turbocharger. Refer to Disassembly and Assembly, “Turbocharger - Install”. i02288273

Turbocharger - Install SMCS Code: 1052-012

SMCS Code: 1052-016


Assembly Procedure

Table 9


Required Tools

Contaminants may cause rapid wear and shortened component life. NOTICE The compressor housing must remain straight with the turbocharger cartridge during disassembly and assembly. Tilting may cause damage to the tips of the compressor wheel and the compressor shaft.

Illustration 50

g01145263

Tool

Part Number

A

5P-3931

Part Description Anti-Seize Compound

Qty 1


Illustration 51

g01148173

RENR9716-02

Illustration 52


g01145002

g01218139

Illustration 53

1. Position the gasket on the exhaust manifold.

2. Remove locknuts (6) from exhaust manifold (7).

2. Apply Tooling (A) to the threads of the exhaust manifold studs.

3. Remove spacers (2) and (3) from exhaust manifold (7).

3. Attach a suitable lifting device to turbocharger (5). The weight of turbocharger (5) is approximately 45 kg (100 lb). Position turbocharger (5) on the exhaust manifold.

4. Remove exhaust manifold (7) and gaskets (1) from the cylinder head.

4. Install nuts (3) and tighten to a torque of 55 ± 9 N·m (41 ± 7 lb ft). 5. Connect tube assemblies (1) and tube assembly (4). 6. Install tube assembly (2). 7. Fill the cooling system. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

5. If necessary, remove clamps (4) and expansion joints (5).


Required Tools Tool

Part Number

Part Description

Qty

A

5P-3931

Anti-Seize Compound

-

B

165-4638

Guide

3

i02617122

Exhaust Manifold - Remove and Install SMCS Code: 1059-010

Removal Procedure Start By: a. Remove the turbocharger. Refer to Disassembly and Assembly, “Turbocharger - Remove”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Remove the shield assemblies from the exhaust manifolds.

Illustration 54

g01218139


RENR9716-02

i02300073

Inlet and Exhaust Valve Springs - Remove and Install SMCS Code: 1108-010


Required Tools

Illustration 55

g00566145

1. If necessary, install expansion joints (5) and clamps (4). Tighten the clamps to a torque of 8.5 ± 1.0 N·m (75 ± 9 lb in). 2. Apply Tooling (A) to the studs prior to assembly. If necessary, install the studs and tighten to a torque of 35 ± 5 N·m (26 ± 4 lb ft).

Tool

Part Number

Part Description

Qty

A

9U-7241

Valve Spring Compressor

1

B

8S-2263

Spring Tester

1

Start By: a. Remove the electronic unit injectors. Refer to Disassembly and Assembly, “Electronic Unit Injector - Remove”.

3. Position gaskets (1) and exhaust manifold (7) on the cylinder head.


4. Install spacers (2) and (3) on exhaust manifold (7).


Note: Use Tooling (B) in at least one oversize hole per manifold section in order to align the exhaust manifolds. Do not remove Tooling (B) until removal is required to tighten the locknuts. 5. Install locknuts (6) on exhaust manifold (7). Tighten locknuts (6) in a numerical sequence to a torque of 20 ± 3 N·m (15 ± 2 lb ft). Tighten locknuts (6) again in a numerical sequence to a torque of 38 ± 5 N·m (28 ± 4 lb ft).

Note: Place the piston at the top of the compression stroke (TC). Remove the valve springs for that cylinder. If the valves fall into the cylinder liner, then the cylinder head must be removed. 1. Position the No. 1 piston at the top center of the compression stroke. Refer to Testing and Adjusting, “Finding Top Center Position for No. 1 Piston”.

6. Install the shield assemblies on the exhaust manifolds. End By: a. Install the turbocharger. Refer to Disassembly and Assembly, “Turbocharger - Install”.

Illustration 56

g01073852

RENR9716-02


NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Lubricate the valve stems with clean engine oil.

g01043625

Illustration 57

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment.

Illustration 58

g01043625

Follow the recommended procedure and use all recommended tooling to release the spring force. 2. Install Tooling (A) in the electronic unit injector sleeve. Secure Tooling (A) with unit injector clamp (1). 3. Tighten the full nut until valve spring keepers (3) are loose on valve (2). 4. Remove valve spring keepers (3) from the valve. 5. Carefully remove Tooling (A).

Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 2. Ensure that washer (7) is installed on the valve guide. 3. Install inner valve spring (5) and outer valve spring (6) on valve (2).

6. Remove valve rotator (4). 7. Remove outer valve spring (6) and inner valve spring (5) from the valve.

4. Install valve rotator (4) on valve (2).

8. Remove washer (7) from the valve guide. 9. Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, “Cylinder Head Valves” for additional information on the valve springs.


Required Tools Tool

Part Number

Part Description

Qty

A

9U-7241


1

The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves. 5. Use Tooling (A) to compress inner valve spring (5) and outer valve spring (6). Install valve spring keepers (3) on valve (2). Remove unit injector clamp (1) and Tooling (A).


RENR9716-02

End By: a. Install the electronic unit injectors. Refer to Disassembly and Assembly, “Electronic Unit Injector - Install”. i02642655

Inlet and Exhaust Valves Remove and Install SMCS Code: 1105-010


Required Tools Tool

Part Number

Part Description

Qty

A

5S-1330


1

B

8S-2263

Spring Tester

1

Start By: a. Remove the cylinder head. Refer to Disassembly and Assembly, “Cylinder Head - Remove”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 59

g01015263

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 1. Install Tooling (A) and compress the valve springs. Remove valve spring keepers (2) from valve (1). 2. Carefully remove Tooling (A) from valve (1). 3. Remove valve rotator (3). 4. Remove outer valve spring (5) and inner valve spring (4) from valve (1). 5. Remove washer (6) and valve (1) from the valve guide. 6. Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, “Cylinder Head Valves” for additional information on the valve springs. 7. Inspect the valves. Refer to Specifications, “Cylinder Head Valves” for additional information on the inlet and exhaust valves.

RENR9716-02



3. Install inner valve spring (4) and outer valve spring (5) on valve (1).

Table 14

4. Install valve rotator (3) on valve (1).

Required Tools Tool A

Part Number 5S-1330

Part Description Valve Spring Compressor

Qty 1


5. Use Tooling (A) to compress inner valve spring (4) and outer valve spring (5). Install valve spring keepers (2) on valve (1).

Note: A small amount of grease can be used to hold the retainer locks in position during installation.

The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.

1. Lubricate the valves with clean engine oil. Install the valves in the cylinder head.

6. Carefully remove Tooling (A).


End By: a. Install the cylinder head. Refer to Disassembly and Assembly, “Cylinder Head - Install”. i02109151

Inlet and Exhaust Valve Guides - Remove and Install SMCS Code: 1104-010


Required Tools Tool

Part Number

A(1)

9U-6895

(1)

Part Description Valve Guide Driver

Qty 1

Part of 9U-7530 Engine Tool Group

Start By:

Illustration 60

g01015263

a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, “Inlet and Exhaust Valves - Remove and Install”. NOTICE Keep all parts clean from contaminants.

Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 2. Install washer (6) on the valve guide.



RENR9716-02

Note: Tooling (B) must be used in order to install the valve guide to the correct height. Height to top of valve guide from cylinder head surface ..... 35.00 ± 0.50 mm (1.378 ± 0.020 inch) Note: For more information, refer to Specifications, “Cylinder Head Valves”. 3. Install valve stem seal (1) on the valve guide. End By:

g01073841

Illustration 61

a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, “Inlet and Exhaust Valves - Remove and Install”.

1. Remove valve stem seal (1) from valve guide (2). i02288478

2. Use Tooling (A) and a hammer to remove the valve guide from the cylinder head.

Inlet and Exhaust Valve Seat Inserts - Remove and Install


SMCS Code: 1103-010

Table 16

Removal Procedure

Required Tools Tool

Part Number

A(1)

9U-6895

Valve Guide Driver

1

B(1)

9U-6894

Guide Collar

1

(1)

Part Description

Qty



Table 17

Required Tools Tool

Part Number

A

166-7441

Part Description

Qty

Valve Seat Extractor Tool Group

1

Start By: a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, “Inlet and Exhaust Valves - Remove and Install”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 62

g01073842

1. Lubricate the bores for the valve guides with clean engine oil. 2. Install valve guide (2) in the cylinder head with Tooling (A) and Tooling (B). Illustration 63

g01145463

RENR9716-02


1. Use Tooling (A) to remove valve seat insert (1) from the cylinder head. 2. Clean the bores in the cylinder head for the valve seat inserts. Remove any rough areas from the bores.

i02438648

Engine Oil Filter Base Remove SMCS Code: 1306-011


Removal Procedure

Table 18

Table 19

Required Tools Tool B(1) (1)

Part Number

Required Tools Qty

Tool

Part Number

9U-6898

Valve Seat Driver (Exhaust)

1

A

185-3630

9U-6897

Valve Seat Driver (Inlet)

1

Part Description


Part Description Strap Wrench As

Qty 1



NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates.

Illustration 64

g01079028

1. Lower the temperature of new valve seat insert (1).

1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Engine Oil and Filter Change”.

2. Use Tooling (B) to install the new valve seat insert in the cylinder head. Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem projection. An excessive valve stem projection indicates that the valve seat insert is not seated or material was not cleaned from the bottom of the counterbore. End By: a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, “Inlet and Exhaust Valves - Remove and Install”.

Illustration 65

g01218560


RENR9716-02

2. Use Tooling (A) in order to remove engine oil filters (6).

3. Remove springs (3) and plungers (2) from oil filter base assembly (1).

3. Remove bolts (1), (2), (4), and (5).

i02127824

4. Remove engine oil filter base (3). i02127750

Engine Oil Filter Base Disassemble

Engine Oil Filter Base Assemble SMCS Code: 1306-016

Assembly Procedure

SMCS Code: 1306-015


Disassembly Procedure


Start By: a. Remove the engine oil filter base. Refer to Disassembly and Assembly, “Engine Oil Filter Base - Remove”. 1. Remove the O-ring seals.

Illustration 67

Illustration 66

g01083088

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 2. Remove cover (4).

g01083088

Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 1. Install plungers (2) and springs (3) in oil filter base assembly (1). 2. Install cover (4). 3. Install the O-ring seals.

RENR9716-02


End By:

i02438849

a. Install the engine oil filter base. Refer to Disassembly and Assembly, “Engine Oil Filter Base - Install”. i02438813

Engine Oil Cooler - Remove SMCS Code: 1378-011

Removal Procedure

Engine Oil Filter Base - Install

Start By:

SMCS Code: 1306-012

a. Remove the engine oil filter base. Refer to Disassembly and Assembly, “Engine Oil Filter Base - Remove”.



Table 20

Required Tools Tool

Part Number

A

185-3630

Part Description

Qty


1

Strap Wrench As


NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

Illustration 68

g01218560

1. Position engine oil filter base (3) on the engine oil cooler. 2. Install bolts (1), (2), (4), and (5). 3. Use Tooling (A) to install engine oil filters (6). 4. Refill the engine with engine oil. Refer to Operation and Maintenance Manual, “Engine Oil and Filter - Change”. Illustration 69

2. Remove tube assembly (2). 3. Remove bonnet (1) and the gasket.

g01218689


RENR9716-02

4. Remove engine oil cooler (3).

i02439263

5. Remove the O-ring seals from engine oil cooler (3). i02438914

Engine Oil Cooler - Install

Engine Oil Pump - Remove SMCS Code: 1304-011

Removal Procedure Start By:

SMCS Code: 1378-012

a. Remove the engine oil pan. Refer to Disassembly and Assembly, “Engine Oil Pan - Remove and Install”.



Illustration 70

g01218689

1. Install the O-ring seals on engine oil cooler (3). 2. Lubricate the O-ring seals with clean engine oil or glycerin. 3. Install engine oil cooler (3). 4. Install the gasket and bonnet (1). 5. Install tube assembly (2). 6. Refill the cooling system with coolant. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”. End By: a. Install the engine oil filter base. Refer to Disassembly and Assembly, “Engine Oil Filter Base - Install”.

Illustration 71

g01218847

1. Remove tube assemblies (3) from engine oil pump (2). 2. Remove bolts (1) and engine oil pump (2).

RENR9716-02


i02439652

Engine Oil Pump - Disassemble

3. Remove bolts (4) and separate cover assembly (3) from body assembly (1).

SMCS Code: 1304-015

4. Use Tooling (A) and a suitable press in order to remove the bearings from cover assembly (3).


5. Remove shaft assemblies (2).

Table 21

6. Remove bolts (12) and retainer (11). Required Tools

Tool

Part Number

A

1P-0510

Driver Group

1

B

1P-2320

Puller Assembly

1

Part Description

Qty

7. Remove spring (10), plunger ring (9), and plunger (8). 8. Use Tooling (A) and a suitable press in order to remove the bearings from body assembly (1). i02439997

Start By: a. Remove the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Remove”.

Engine Oil Pump - Assemble SMCS Code: 1304-016

Assembly Procedure


Table 22

Required Tools

Contaminants may cause rapid wear and shortened component life. Tool

Part Number

A

1P-0510

Part Description Driver Group

Qty 1


Illustration 72

g01218982

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 1. Remove bolt (7) and washer (6). 2. Use Tooling (B) to remove drive gear (5) from body assembly (1). Remove the key from the pump shaft.

Illustration 73

g01218982


RENR9716-02

5. Use Tooling (A) to install the bearings in cover assembly (3) until the bearings are even with the outside surface of cover assembly (3). Install the bearings so the junctions in the bearings are Angle (Y). Angle (Y) is 30 ± 15 degrees from the center line of the bearing bores, and toward the outlet passage. The outlet passage has a cavity between the bearing bores. 6. Install cover assembly (3) on body assembly (1). Install bolts (4).

Illustration 74

g01219045

7. Install the key into the pump shaft. Install drive gear (5). Install washer (6) and bolt (7). Tighten bolt (7) to a torque of 55 ± 10 N·m (41 ± 7 lb ft). End By: a. Install the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Install”. i02440080

Engine Oil Pump - Install SMCS Code: 1304-012

Installation Procedure Illustration 75

g01219048

Improper assembly of parts that are spring loaded can cause bodily injury.


To prevent possible injury, follow the established assembly procedure and wear protective equipment. 1. Use Tooling (A) to install the bearings in body assembly (1) until the bearings are even with the outside surface of body assembly (1). Install the bearings so the junctions in the bearings are Angle (X). Angle (X) is 30 ± 15 degrees from the center line of the bearing bores and toward the outlet passage in the engine oil pump. 2. Install plunger (8), plunger ring (9), and spring (10). 3. Install retainer (11) and bolts (12). 4. Install shaft assemblies (2).

Illustration 76

g01218847

1. Position engine oil pump (2) and install bolts (1). 2. Install tube assemblies (3) on engine oil pump (2). End By: a. Install the engine oil pan. Refer to Disassembly and Assembly, “Engine Oil Pan - Remove and Install”.

RENR9716-02


i02440626

Water Pump - Remove SMCS Code: 1361-011

Removal Procedure NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. g01219275


Illustration 78


5. Remove water pump (4).

Contaminants may cause rapid wear and shortened component life. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

4. Remove bolts (6) and nuts (5).

i02451192

Water Pump - Disassemble SMCS Code: 1361-015

Disassembly Procedure Table 23

Required Tools Part Number

Tool

A

B

Part Description

Qty

8S-2264

Puller Group

1

4B-3903

Bolt 5/16 - 18 NC by 4 inch

2

1P-0456

Plate

1

4B-4277

Washer

2

1P-0510

Driver Group

1

Start By: a. Remove the water pump. Refer to Disassembly and Assembly, “Water Pump - Remove”. Illustration 77

2. Remove bolts (1) and bolts (2). 3. Remove cover (3).

g01219274



RENR9716-02

Note: The water pump seal can be replaced without removing the water pump from the engine. Note: An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Do not replace the water pump seal unless a large amount of leakage or a constant flow of coolant is draining from the water pump housing.

i02394663

Water Pump - Assemble SMCS Code: 1361-016

Assembly Procedure Table 24

Required Tools Tool

Part Number

Part Description

Qty

B

1P-0510

Driver Group

1

C

7N-7843

Seal Installation Tool

1

D

6V-1541

Quick Cure Primer

1


Illustration 79

g01195730

1. Remove adapter (15). 2. Remove bolt (9) and washer (8). 3. Use Tooling (A) to remove impeller (5) from shaft (10). 4. Remove bolt (7), washer (6), and gear (4) from shaft (10). 5. Remove bolts (11) and retainer (13). 6. Remove O-ring seal (14) from housing (3).

Illustration 80

g01195730

7. Use a suitable press to remove shaft (10) and bearing assembly (1) from housing (3).

1. Use Tooling (B) to install lip seal (2) into the housing.

8. Use a suitable press to remove bearing assembly (1) from shaft (10).

2. Apply Tooling (D) to shaft (10). Use a suitable press to install bearing assembly (1) on shaft (10).

9. Remove seal assembly (12) from housing (3).

3. Install shaft (10) and bearing assembly (1) in housing (3).

10. Use Tooling (B) to remove lip seal (2) from the housing.

4. Install O-ring seal (14) on housing (3). 5. Install retainer (13) and bolts (11). 6. Position gear (4) on shaft (10). Install washer (6) and bolt (7).

RENR9716-02


7. Use Tooling (C) to install seal assembly (12) onto shaft (10) until the stationary cup is fully seated into housing (3). 8. Install impeller (5) on shaft (10). Install washer (8) and bolt (9). Tighten bolt (9) to a torque of 39 ± 3 N·m (29 ± 2 lb ft). 9. Install adapter (15). End By: a. Install the water pump. Refer to Disassembly and Assembly, “Water Pump - Install”. i02440675

Water Pump - Install SMCS Code: 1361-012 Illustration 82


g01219274

3. Position cover (3) on the water pump.


4. Install bolts (2) and bolts (1).


5. Fill the cooling system. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”. i02440754

Water Temperature Regulator Housing - Remove and Install SMCS Code: 1393-010

Removal Procedure 1. Drain the coolant from the cooling system into a suitable container for storage or disposal until the coolant is below the level of the water temperature regulator housing. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

Illustration 81

g01219275

1. Position water pump (4) in the front housing. 2. Install nuts (5) and bolts (6).


RENR9716-02

g01219336

Illustration 83

2. Disconnect hose assembly (1) and elbow (3). 3. Remove bolts (2) and bolts (4). Remove water temperature regulator housing (5).

g01223744

Illustration 84

4. Remove O-ring seals (6) and water temperature regulators (7) from water temperature regulator housing (5). 5. If necessary, remove the lip seals.

Table 25


A

221-8647

Part Description Seal Installer Gp

g01223744

2. Install water temperature regulators (7) and O-ring seals (6) in water temperature regulator housing (5).

Illustration 86

g01219336

3. Position water temperature regulator housing (5) on the engine. Install bolts (4) and bolts (2). 4. Connect elbow (3) and hose assembly (1). 5. Fill the cooling system. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.


Tool

Illustration 85

Qty 1

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. If necessary, use Tooling (A) to install the lip seals.

RENR9716-02


i02576096

Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Remove SMCS Code: 1063-011; 1353-011; 1712-011


Required Tools Tool

Part Number

A

189-0410

Part Description

Qty

Shackle As

2

Illustration 88

g01290915

3. Disconnect bottom aftercooler tube (2).

Start By: a. Remove the fan. Refer to Disassembly and Assembly, “Fan - Remove and Install”. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Illustration 89

g01290916

4. Disconnect top radiator hose (3).

Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant (ELC) - Change”.

Illustration 90

5. Disconnect top aftercooler tube (4).

Illustration 87

g01290908

2. Remove clamp (1). Repeat for the opposite side.

g01290917


Illustration 91

RENR9716-02

g01290930

6. Disconnect bottom radiator hose (5). Disconnect bottom aftercooler tube (6).

Illustration 92

g01290940

Illustration 94

9. Attach Tooling (A) and a suitable lifting device onto cooling package (10). The weight of cooling package (10) is approximately 544 kg (1200 lb).

g01290934 g01290941

Illustration 95

7. Disconnect hose assembly (8) from fuel cooler (7).

10. Remove bolts (11). Repeat for the opposite side. Remove cooling package (10). i02576308

Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Install SMCS Code: 1063-012; 1353-012; 1712-012

Installation Procedure Illustration 93

g01290939


Table 27

Required Tools Tool

Part Number

A

189-0410

Part Description Shackle As

Qty 2

RENR9716-02



Illustration 98

g01290939

3. Connect hose assembly (9) onto fuel cooler (7).

Illustration 96

g01290940

1. Attach Tooling (A) and a suitable lifting device onto cooling package (10). The weight of cooling package (10) is approximately 544 kg (1200 lb).

Illustration 97

g01290941

2. Install cooling package (10). Install bolts (11). Repeat for the opposite side.

Illustration 99

g01290934


Illustration 100

g01290930

5. Connect bottom aftercooler tube (6). Connect bottom radiator hose (5).


Illustration 101

RENR9716-02

g01290917

6. Connect top aftercooler tube (4).

g01290908

Illustration 104

9. Install clamp (1). Repeat for the opposite side. 10. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, “Cooling System Coolant (ELC) - Change”. End By: a. Install the fan. Refer to Disassembly and Assembly, “Fan - Remove and Install”. i02584900

Aftercooler - Remove Illustration 102

g01290916

SMCS Code: 1063-011

Removal Procedure

7. Connect top radiator hose (3).

Table 28

Required Tools Tool

Part Number

A

189-0410

Part Description

Qty

Shackle As

Start By: a. Remove the fan. Refer to Disassembly and Assembly, “Fan - Remove and Install”.

Illustration 103

8. Connect bottom aftercooler tube (2).

g01290915

2

RENR9716-02


NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant (ELC) - Change”.

Illustration 107

g01290916

4. Disconnect top radiator hose (3).

Illustration 108

g01290917

5. Disconnect top aftercooler tube (4). Illustration 105

g01290908

2. Remove clamp (1). Repeat for the opposite side.

Illustration 109

Illustration 106

3. Disconnect bottom aftercooler tube (2).

g01290915

g01290930

6. Disconnect bottom radiator hose (5). Disconnect bottom aftercooler tube (6).


Illustration 110

RENR9716-02

g01290934


Illustration 111

g01294232

Illustration 113

10. Attach Tooling (A) and a suitable lifting device onto aftercooler (12). The weight of aftercooler (12) is approximately 227 kg (500 lb).

g01290939


g01294234

Illustration 114

11. Remove bolt (13). Remove bolts (14) and bolts (15) from aftercooler (12). 12. Repeat Step 9 through Step 11 for the opposite side. 13. Remove aftercooler (12). i02585968

Aftercooler - Install SMCS Code: 1063-012 Illustration 112

9. Remove bolts (10). Remove bolt (11).

g01294215


Required Tools Tool

Part Number

A

189-0410

Part Description Shackle As

Qty 2

RENR9716-02

Illustration 115


g01294232

1. Attach Tooling (A) and a suitable lifting device onto aftercooler (12). The weight of aftercooler (12) is approximately 227 kg (500 lb). Install aftercooler (12).

Illustration 118


Illustration 119

Illustration 116

g01294234

g01290939

g01290934


2. Install bolts (14) and bolts (15) into aftercooler (12). Install bolt (13).

Illustration 120

Illustration 117

g01294215

3. Install bolt (11). Install bolts (10). 4. Repeat Step 2 and Step 3 for the opposite side.

g01290930

7. Connect bottom aftercooler tube (6). Connect bottom radiator hose (5).


Illustration 121

RENR9716-02

g01290917

8. Connect top aftercooler tube (4).

g01290908

Illustration 124

11. Install clamp (1). Repeat for the opposite side. 12. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, “Cooling System Coolant (ELC) - Change”. End By: a. Install the fan. Refer to Disassembly and Assembly, “Fan - Remove and Install”. i02581106

Radiator Core - Remove Illustration 122

g01290916

SMCS Code: 1353-011; 1353-011-KO

Removal Procedure

9. Connect top radiator hose (3).

Table 30

Required Tools Tool

Part Number

A

138-7575

Part Description Link Bracket

Qty 2

Start By: a. Remove the aftercooler. Refer to Disassembly and Assembly, “Aftercooler - Remove”.

Illustration 123

10. Connect bottom aftercooler tube (2).

g01290915

RENR9716-02



Illustration 127

g01294577

3. Remove the upper and the lower braces (3).

Illustration 125

g01292911

1. Remove the upper and the lower radiator guards (1).

Illustration 126

Illustration 128

g01294578

4. Remove bolts (4) and remove bolts (5).

g01292912

2. Attach Tooling (A) and a suitable lifting device onto radiator top tank (2). The weight of the radiator is approximately 227 kg (500 lb). Illustration 129

5. Remove bolts (6).

g01294579


RENR9716-02

Illustration 132

g01292912

1. Attach Tooling (A) and a suitable lifting device onto radiator top tank (2). The weight of the radiator is approximately 227 kg (500 lb). g01294580

Illustration 130

6. Remove bolts (7). Remove bolts (8). Remove support (9). 7. Repeat Steps 4 through 6 for the opposite side.

Illustration 133

g01294602

2. Install radiator (10). Install bolts (11). Repeat for the opposite side.

g01294602

Illustration 131

8. Remove bolts (11). Repeat for the opposite side. Remove radiator (10). i02585957

Radiator Core - Install SMCS Code: 1353-012-KO; 1353-012


Required Tools Tool

Part Number

A

138-7575

Part Description

Qty Illustration 134

Link Bracket

2

g01294580

3. Install support (9). Install bolts (8). Install bolts (7).

RENR9716-02


Illustration 138

g01292911

8. Install the upper and the lower radiator guards (1). End By: Illustration 135

g01294579

a. Install the aftercooler. Refer to Disassembly and Assembly, “Aftercooler - Install”.

4. Install bolts (6). i02444868

Engine Support (Front) Remove and Install SMCS Code: 1154-010-FR

Removal Procedure (Type 1) Start By: a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly, “Vibration Damper and Pulley - Remove and Install”. Illustration 136

g01294578

1. Support the front of the engine.

5. Install bolts (4) and bolts (5). 6. Repeat Steps 3 through 5 for the opposite side.

Illustration 139

2. Remove bolts (1). Illustration 137

7. Install the upper and the lower braces (3).

g01294577

3. Remove engine support (2).

g01221659


RENR9716-02

Installation Procedure (Type 1)

Illustration 140

g01221659

1. Position engine support (2) on the engine.

Installation Procedure (Type 2)

g01221663

Illustration 142

2. Install bolts (1).

1. Use a suitable lifting device to position engine support (4) on the engine. The weight of engine support (4) is approximately 35 kg (77 lb).

End By:

2. Install bolts (3).

a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, “Vibration Damper and Pulley - Remove and Install”.

End By:

Removal Procedure (Type 2)

a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, “Vibration Damper and Pulley - Remove and Install”.

Start By:

i02440962

a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly, “Vibration Damper and Pulley - Remove and Install”. 1. Support the front of the engine.

Gear Group (Rear) - Remove SMCS Code: 1206-011; 1212-011


Required Tools Tool

Part Number

A

1P-0510


Qty 1

Start By: a. Remove the flywheel housing. Refer to Disassembly and Assembly, “Flywheel Housing - Remove and Install”. Illustration 141

g01221663

2. Remove bolts (3). 3. Use a suitable lifting device to remove engine support (4). The weight of engine support (4) is approximately 35 kg (77 lb).

RENR9716-02


NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products.

4. Use Tooling (A) and a suitable press to remove the bearing from gear assembly (6). 5. Remove bolts (2), gear assembly (1), and shaft assembly (3). 6. Use Tooling (A) and a suitable press to remove the bearing from gear assembly (1). 7. Remove gear assembly (12). 8. Remove bolts (5) and gear assemblies (4).

Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 144

g01219500

9. Remove bolts (16) and shaft assembly (17). 10. Remove bolts (13), thrust plates (14), and adapter assemblies (15). 11. Use bolt (13) in order to remove the sealing plates. Remove the O-ring seals.

Illustration 143

g01219485

1. Remove bolts (10), thrust plate (11), and gear assembly (9). 2. Use Tooling (A) and a suitable press to remove the bearing from gear assembly (9). 3. Remove bolts (8), gear assembly (6), and shaft assembly (7).


RENR9716-02

i02442469

Gear Group (Rear) - Install SMCS Code: 1206-012; 1212-012


Required Tools Tool

Part Number

A

1P-0510


Qty 1

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: Apply clean engine oil to the bearings and the shaft assemblies prior to installation on the engine.

Illustration 146

g01220275

Illustration 147

g01151468

4. Refer to Testing and Adjusting, “Rear Gear Group - Time” for additional information.

Illustration 145

g01219500

Note: Align the Timing Marks on gear assemblies (4) with the Timing Marks on the rear housing and align the dowels on gear assemblies (4) with the adapter assemblies. 5. Position gear assemblies (4) and install bolts (5).

1. Install the O-ring seals and the sealing plates on the cylinder head.

6. Install gear assembly (12).

2. Install adapter assemblies (15), thrust plates (14), and bolts (13).

7. Use Tooling (A) and a suitable press to install the bearing in gear assembly (1). Install the bearing to a depth of 2.6 ± 0.5 mm (0.10 ± 0.02 inch).

3. Position shaft assembly (17) and install bolts (16).

RENR9716-02


8. Install shaft assembly (3), gear assembly (1), and bolts (2). 9. Use Tooling (A) and a suitable press to install the bearing in gear assembly (6). Install the bearing to a depth of 2.6 ± 0.5 mm (0.10 ± 0.02 inch). 10. Install shaft assembly (7), gear assembly (6), and bolts (8). 11. Use Tooling (A) and a suitable press to install the bearing in gear assembly (9). Install the bearing to a depth of 2.5 ± 0.5 mm (0.10 ± 0.02 inch). Note: Align the Timing Mark on gear assembly (9) with the Timing Mark on gear assembly (12).

Illustration 149

12. Install gear assembly (9), thrust plate (11), and bolts (10).

1. Remove two bolts (1). Install Tooling (A) in the crankshaft.

13. Tighten the bolts on gear assemblies (4) to a torque of 240 ± 40 N·m (177 ± 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.

2. Remove remaining bolts (1). Slide flywheel (2) away from the engine on Tooling (A).

End By: a. Install the flywheel housing. Refer to Disassembly and Assembly, “Flywheel Housing - Remove and Install”. i02752668

Flywheel - Remove and Install

g01220438

3. Attach a suitable lifting device to flywheel (2). The weight of flywheel (2) is approximately 130 kg (285 lb). Remove flywheel (2). 4. If necessary, use a hammer and a punch in order to remove ring gear (3) from flywheel (2).


Required Tools Tool

Part Number

Removal Procedure

A

-

Table 34

B

6V-4876

SMCS Code: 1156-010

Part Description

Qty

Guide Stud 5/8 - 18 UNF by 11 inch

2

Lubricant

-

Required Tools Tool

Part Number

A

-

Part Description Guide Stud 5/8 - 18 UNF by 11 inch

Qty 2

Illustration 150

Illustration 148

g01220437

g01220438


RENR9716-02


g01220437

Illustration 151

Note: Ring gear (3) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when the flywheel is installed. 1. Raise the temperature of ring gear (3). Install ring gear (3) on flywheel (2).

g01220531

Illustration 152

2. Install Tooling (A) in the crankshaft.

1. Use Tooling (A) or a punch and hammer in order to puncture three or more holes in crankshaft rear seal (1).

3. Attach a suitable lifting device to flywheel (2). The weight of flywheel (2) is approximately 130 kg (285 lb). Position flywheel (2) on the crankshaft.

2. Use Tooling (A) to remove crankshaft rear seal (1) and crankshaft wear sleeve (2).

4. Apply Tooling (B) to the threads of bolts (1).

i02442921

Crankshaft Rear Seal - Install

5. Install bolts (1). Remove Tooling (A). Install remaining bolts (1). 6. Tighten bolts (1) to a torque of 100 ± 5 N·m (75 ± 4 lb ft). Turn the bolts for an additional 180 ± 5 degrees. 7. Check the flywheel runout. Refer to Testing and Adjusting, “Flywheel - Inspect”. i02442878

SMCS Code: 1161-012


Required Tools Tool

Crankshaft Rear Seal - Remove SMCS Code: 1161-011

Removal Procedure

B

Table 36

Required Tools Tool

Part Number

A

1U-7600

Part Description Slide Hammer Puller

Qty 1

Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, “Flywheel - Remove and Install”.

(1) (2)

Part Number

Part Description

Qty

249-2937(1)

Seal Locator As

1

5P-7310(1)

Bolt

3

9S-8858(1)

Nut (Seal Installer)

1

6V-6143(1)

Seal Installer

1

5P-1733(2)

Seal Locator As

1

5P-7309(2)

Bolt

3

9S-8858(2)


1

6V-6142(2)

Seal Installer

1

Large crankshaft gear Small crankshaft gear

RENR9716-02



b. Remove the electric starting motor. Refer to Disassembly and Assembly, “Electric Starting Motor - Remove and Install”.



g01220558

Illustration 153

1. Clean the outside diameter of the crankshaft. Note: Install the crankshaft rear seal with the arrow that shows the direction of crankshaft rotation toward the rear of the engine. 2. Use Tooling (B) to install crankshaft wear sleeve (2) and crankshaft rear seal (1) as a unit. End By: a. Install the flywheel. Refer to Disassembly and Assembly, “Flywheel - Remove and Install”. i02752908

Illustration 154

g01220951

Flywheel Housing - Remove and Install

1. Disconnect hose assemblies (1) from flywheel housing (2).

SMCS Code: 1157-010

2. Disconnect fuel filter base (5) from flywheel housing (2). Reposition fuel filter base (5) and the hose assemblies.

Removal Procedure

3. Remove two bolts (4) and install Tooling (B).

Table 38

Required Tools Tool

Part Number

A

138-7574

B

-

Part Description

Qty

Link Bracket

2

Guide Stud 1/2 - 13 NC by 7 inch

2

Start By: a. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, “Crankshaft Rear Seal - Remove”.

4. Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 110 kg (245 lb). 5. Remove remaining bolts (4), bolts (6), and bolts (3). Remove flywheel housing (2) and the gasket from the rear housing.


RENR9716-02


Required Tools Tool

Part Number

A

138-7574

B

-

Part Description

Qty

Link Bracket

2

Guide Stud 1/2 - 13 NC by 7 inch

2


Illustration 156

g01221009

1. Install Tooling (B) in the cylinder block. 2. Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 110 kg (245 lb). 3. Position the gasket and flywheel housing (2) on the rear housing. Install bolts (3), bolts (6), and bolts (4). 4. Remove Tooling (B) and install remaining bolts (4). 5. Tighten the bolts, as follows:

Illustration 155

g01220951

a. In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of 55 ± 10 N·m (41 ± 7 lb ft). b. In a numerical sequence, tighten Bolt 3 through Bolt 10 to a torque of 135 ± 20 N·m (100 ± 15 lb ft). c. In a numerical sequence, tighten Bolt 11 through Bolt 36 to a torque of 47 ± 9 N·m (35 ± 7 lb ft). 6. Reposition fuel filter base (5) and the hose assemblies. Connect fuel filter base (5) to flywheel housing (2). 7. Connect hose assemblies (1) to flywheel housing (2).

RENR9716-02


End By: a. Install the electric starting motor. Refer to Disassembly and Assembly, “Electric Starting Motor - Remove and Install”. b. Install the crankshaft rear seal. Refer to Disassembly and Assembly, “Crankshaft Rear Seal - Install”. i02443805

Vibration Damper and Pulley Remove and Install SMCS Code: 1205-010

1. Remove V-belt (1) from the engine.

Removal Procedure

2. Remove two bolts (2) and install Tooling (A).

Table 40

3. Remove remaining bolts (2) and pulley (3).

Required Tools Tool

Part Number

A

-

g01221078

Illustration 158

4. Slide vibration damper (4) along Tooling (A). Part Description Guide Stud 1/2 - 13 NC by 5 inch

Qty 2

5. Attach a suitable lifting device onto vibration damper (4). The weight of vibration damper (4) is approximately 34 kg (75 lb). Remove vibration damper (4) from the adapter.


Required Tools

Illustration 157

Tool

Part Number

A

-

Part Description Guide Stud 1/2 - 13 NC by 5 inch

Qty 2

g01221066

Illustration 159

g01221078


RENR9716-02


g01221066

Illustration 160

1. Install Tooling (A) in the adapter.

Illustration 161

g01221272

1. Remove bolts (1) and adapter (2).

2. Attach a suitable lifting device onto vibration damper (4). The weight of vibration damper (4) is approximately 34 kg (75 lb). Position vibration damper (4) on the adapter. 3. Install pulley (3) and bolts (2). 4. Remove Tooling (A). Install remaining bolts (2). Tighten bolts (2) to a torque of 135 ± 20 N·m (100 ± 15 lb ft). 5. Install V-belt (1) on the engine. i02444403

Crankshaft Front Seal Remove

3. Use Tooling (A) to remove crankshaft front seal (4).



A

1U-7600

Part Description

g01221276

2. Use Tooling (A) or a punch and hammer in order to puncture three or more holes in crankshaft front seal (4).

SMCS Code: 1160-011

Tool

Illustration 162

Qty

Slide Hammer Puller

Start By: a. Remove the crankshaft vibration damper and pulley. Refer to Disassembly and Assembly, “Vibration Damper and Pulley - Remove and Install”.

1

4. If necessary, use Tooling (A) or a punch and hammer in order to puncture three or more holes in crankshaft wear sleeve (3). Use Tooling (A) to remove crankshaft wear sleeve (3).

RENR9716-02


i02444556

Crankshaft Front Seal - Install SMCS Code: 1160-012


Required Tools Tool

B

Part Number

Part Description

Qty

5P-1733

Seal Locator

1

5P-1737

Bolt

3

Illustration 164

9S-8858


1

3. Install adapter (2) and bolts (1).

6V-6142

Seal Installer

1


g01221272

End By: a. Install the crankshaft vibration damper and pulley. Refer to Disassembly and Assembly, “Vibration Damper and Pulley - Remove and Install”. i02292422

1. Clean the outside diameter of the crankshaft.

Gear Group (Front) - Remove SMCS Code: 1206-011

Removal Procedure Start By: a. Remove the front housing. Refer to Disassembly and Assembly, “Housing (Front) - Remove”. NOTICE Keep all parts clean from contaminants. Illustration 163

g01221389

2. Use Tooling (B) to install crankshaft front seal (4) and crankshaft wear sleeve (3) as a unit. Note: Install the crankshaft front seal with the arrow that shows the direction of crankshaft rotation toward the front of the engine.



RENR9716-02

Illustration 167

g01147620

1. Apply clean engine oil to shaft (7), the bearing bore, and the thrust faces prior to installation. Install shaft (7) and bolts (6). Tighten bolts (6) to a torque of 55 ± 10 N·m (41 ± 7 lb ft). Illustration 165

g01147593

1. Remove bolts (5) and gear assembly (4). 2. Remove bolts (3) and plate (2). Remove gear assembly (1).

Illustration 166

g01147620

3. Remove bolts (6) and shaft (7).

Illustration 168

g01147593

2. Position gear assembly (1) on the shaft. Install plate (2) and bolts (3). i02691256

Gear Group (Front) - Install SMCS Code: 1206-012


3. Install gear assembly (4) and bolts (5). End By: a. Install the front housing. Refer to Disassembly and Assembly, “Housing (Front) - Install”.

RENR9716-02


i02445219

Housing (Front) - Remove SMCS Code: 1151-011

Removal Procedure Start By: a. Remove the water temperature regulator housing. Refer to Disassembly and Assembly, “Water Temperature Regulator Housing - Remove and Install”. b. Remove the water pump. Refer to Disassembly and Assembly, “Water Pump - Remove”. c. Remove the crankshaft front seal. Refer to Disassembly and Assembly, “Crankshaft Front Seal - Remove”. d. Remove the front engine support. Refer to Disassembly and Assembly, “Engine Support (Front) - Remove and Install”. e. Remove the alternator. Refer to Disassembly and Assembly, “Alternator - Remove and Install”. f. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, “Crankshaft Position Sensor - Remove and Install”.

Illustration 169

g01221893

1. Disconnect hose assemblies (2) from front housing (4). 2. Remove covers (1). 3. Remove alternator bracket (3) from front housing (4).

g. Remove the camshaft position sensor. Refer to Disassembly and Assembly, “Camshaft Position Sensor - Remove and Install”. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 170

4. Remove bolts (5) and dampers (6).

g01221941


RENR9716-02

i02445708

Housing (Front) - Install SMCS Code: 1151-012


Required Tools

Illustration 171

Tool

Part Number

A

4C-9612

Part Description Silicone Sealant

Qty 1

g01221953


5. Disconnect bracket (7) and elbows (8).


Illustration 172

g01221955

6. Remove adapters (9). 7. Attach a suitable lifting device to front housing (4). The weight of front housing (4) is approximately 70 kg (155 lb). 8. Remove bolts (10) and bolts (11). 9. Remove front housing (4) and the gasket.

Illustration 173

g01221955

1. Apply Tooling (A) to the bottom of front housing (4) at the junction of the cylinder block and the engine oil pan. 2. Attach a suitable lifting device to front housing (4). The weight of front housing (4) is approximately 70 kg (155 lb). Position the gasket and front housing (4) on the dowel pins on the cylinder block. 3. Install bolts (10) and bolts (11). 4. Trim the gasket between the front housing and the cylinder block even with the bottom of the front housing. 5. Install adapters (9).

RENR9716-02

Illustration 174


g01221953

6. Connect elbows (8) and bracket (7).

Illustration 177

g01221893

9. Install alternator bracket (3) on front housing (4). 10. Install covers (1). 11. Connect hose assemblies (2) to front housing (4). End By:

Illustration 175

g01221941

a. Install the camshaft position sensor. Refer to Disassembly and Assembly, “Camshaft Position Sensor - Remove and Install”. b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, “Crankshaft Position Sensor - Remove and Install”. c. Install the alternator. Refer to Disassembly and Assembly, “Alternator - Remove and Install”. d. Install the front engine support. Refer to Disassembly and Assembly, “Engine Support (Front) - Remove and Install”.

Illustration 176

g01151441

7. Install dampers (6) and bolts (5). 8. Tighten the bolts to a torque of 240 ± 40 N·m (177 ± 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.

e. Install the crankshaft front seal. Refer to Disassembly and Assembly, “Crankshaft Front Seal - Install”. f. Install the water pump. Refer to Disassembly and Assembly, “Water Pump - Install”. g. Install the water temperature regulator housing. Refer to Disassembly and Assembly, “Water Temperature Regulator Housing - Remove and Install”.


RENR9716-02

i02290579

Housing (Rear) - Remove SMCS Code: 1157-011

Removal Procedure Start By: a. Remove the rear gear group. Refer to Disassembly and Assembly, “Gear Group (Rear) - Remove”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Remove the bolts that hold the engine oil pan to the rear housing.

g01147138

Illustration 179

2. Disconnect hose assembly (1). 3. Remove bolts (2). 4. Attach a suitable lifting device to rear housing (4). The weight of rear housing (4) is approximately 84 kg (185 lb). 5. Remove bolts (3). 6. Remove rear housing (4) and the gasket. i02291566

Illustration 178

g01147132

Housing (Rear) - Install SMCS Code: 1157-012


Required Tools Tool

Part Number

A

4C-9612

Part Description Silicone Sealant

Qty 1

RENR9716-02


NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Apply Tooling (A) to the bottom of the rear housing at the junction of the cylinder block and the engine oil pan.

Illustration 181

g01147149

2. Attach a suitable lifting device to rear housing (4). The weight of rear housing (4) is approximately 84 kg (185 lb). 3. Position the gasket on rear housing (4).

Illustration 180

g01147138

4. Position rear housing (4) on the cylinder block. Install bolts (3). Tighten bolts (3) in a numerical sequence to a torque of 55 ± 10 N·m (41 ± 7 lb ft). 5. Trim the gasket between the rear housing and the cylinder block even with the bottom of the rear housing.


RENR9716-02

Illustration 183

g01147941

1. Remove bolts (1) and valve mechanism covers (2).

Illustration 182

g01147132

Installation Procedure NOTICE Keep all parts clean from contaminants.

6. Install bolts (2). 7. Connect hose assembly (1). 8. Install the bolts that hold the engine oil pan to the rear housing.


9. Tighten all the bolts that hold the engine oil pan evenly in order to raise the engine oil pan into position. End By: a. Install the rear gear group. Refer to Disassembly and Assembly, “Gear Group (Rear) - Install”. i02293132

Valve Mechanism Cover Remove and Install SMCS Code: 1107-010

Illustration 184

g01147941

1. Position valve mechanism covers (2) on the valve mechanism cover base. Install bolts (1).

Removal Procedure

i02293148


Valve Mechanism Cover Base Remove and Install


SMCS Code: 1120-010

Removal Procedure Start By: a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, “Valve Mechanism Cover - Remove and Install”.

RENR9716-02



g01147965

Illustration 186

1. Install the seal on valve mechanism cover base (3).

Illustration 185

g01147965

1. Remove tube assemblies (1). 2. Disconnect harness assemblies (5) and harness assembly (2).

2. Position valve mechanism cover base (3) on the cylinder head and install bolts (4). 3. Position harness assemblies (5) on the electronic unit injectors. Tighten the cap nuts to a torque of 1.70 ± 0.25 N·m (15 ± 2 lb in). 4. Connect harness assembly (2).

3. Remove bolts (4).

5. Install tube assemblies (1).

4. Remove valve mechanism cover base (3) and the seal from the cylinder head.

End By:


a. Install the valve mechanism cover. Refer to Disassembly and Assembly, “Valve Mechanism Cover - Remove and Install”.


i02293245

Rocker Arm and Shaft Remove SMCS Code: 1102-011


Required Tools Tool

Part Number

A

124-2946

Part Description Lifting Bracket

Qty 1


RENR9716-02

Start By: a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, “Valve Mechanism Cover - Remove and Install”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 188

g01047557

1. Remove valve rocker arms (11) and electronic unit injector rocker arm (3) from rocker shaft assembly (4). 2. Remove jam nut (7) from adjustment screw (8). 3. Remove adjustment screw (8) from valve rocker arms (11). 4. Remove button (10) from adjustment screw (8). Remove O-ring seal (9) from the adjustment screw. 5. Remove jam nut (2) from unit injector adjustment screw (1). Illustration 187

g01148045

1. Remove bolts (2). 2. Use Tooling (A) to remove rocker arm shaft assembly (4), valve rocker arms (3), and electronic unit injector rocker arms (1) as a unit.

6. Remove unit injector adjustment screw (1) from electronic unit injector rocker arm (3). 7. Remove button (6) from unit injector adjustment screw (1). Remove O-ring seal (5) from the unit injector adjustment screw. i02451120

i02451112

Rocker Arm - Disassemble SMCS Code: 1123-015


Rocker Arm - Assemble SMCS Code: 1123-016

Assembly Procedure

Start By:


a. Remove the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, “Rocker Arm and Shaft - Remove”.



RENR9716-02


i03203773

Rocker Arm and Shaft - Install SMCS Code: 1102-012


Required Tools

Illustration 189

Tool

Part Number

A

124-2946

Part Description Lifting Bracket

Qty 1

g01047557

Note: Do not reuse the O-ring seal on the adjustment screw if the button is removed from the adjustment screw. 1. Install O-ring seal (9) in button (10).


2. Use a soft hammer to seat button (10) on adjustment screw (8). 3. Install adjustment screw (8) in valve rocker arms (11). Install jam nut (7) on the adjustment screw. 4. Install O-ring seal (5) in button (6). 5. Use a soft hammer to seat button (6) on unit injector adjustment screw (1). 6. Install unit injector adjustment screw (1) in electronic unit injector rocker arm (3). Install jam nut (2) on the unit injector adjustment screw. 7. Lubricate rocker shaft assembly (4) with clean engine oil. 8. Install valve rocker arms (11) and electronic unit injector rocker arm (3) on rocker shaft assembly (4).

Illustration 190

g01148045

Illustration 191

g01325993

End By: a. Install the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, “Rocker Arm and Shaft - Install”.


RENR9716-02

1. Position rocker arm shaft assembly (4), valve rocker arms (3), and electronic unit injector rocker arms (1) as a unit with Tooling (A) on the cylinder head. 2. Install bolts (2) and tighten to a torque of 50 ± 5 N·m (37 ± 4 lb ft) plus 45 ± 5 degree turn. Tighten the bolts in the following sequence: 2, 3, 4, 1.

NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

3. Adjust the valve lash for the inlet valves and the exhaust valves. Refer to Testing and Adjusting, “Engine Valve Lash - Inspect/Adjust”.

Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products.

4. Adjust the electronic unit injectors. Refer to Testing and Adjusting, “Electronic Unit Injector - Adjust”.


End By: a. Install the valve mechanism cover. Refer to Disassembly and Assembly, “Valve Mechanism Cover - Remove and Install”.


i02446003

NOTICE Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.

Cylinder Head - Remove SMCS Code: 1100-011


Required Tools Tool

Part Number

A

138-7573

B

1U-9200

Part Description

Qty

Link Bracket

3

Lever Puller Hoist

1

1. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

Start By: a. Remove the electronic unit injectors. Refer to Disassembly and Assembly, “Electronic Unit Injector - Remove”. b. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, “Valve Mechanism Cover Base - Remove and Install”. c. Remove the fuel transfer pump. Refer to Disassembly and Assembly, “Fuel Transfer Pump - Remove”.

Illustration 192

2. Remove cover (1).

g01222228

RENR9716-02

Illustration 193


g01222230

3. Remove bolts (2) and gear (3).

Illustration 194

Illustration 196

g01148246

6. Remove elbow (8). Disconnect hose assembly (9).

g01222233

4. Remove bolts (4), thrust plate (5), and adapter assembly (6).

Illustration 197

g01148489

7. Remove elbow (11) and cover (10). 8. Disconnect harness assembly (12) and harness assembly (13). 9. Remove bracket (14).

Illustration 195

g01222234

5. Use bolt (4) in order to remove sealing plate (7). Remove the O-ring seals.

Illustration 198

g01148492


RENR9716-02

10. Remove bolts (15) and damper (16).

15. Attach Tooling (A) and a suitable lifting device to cylinder head (25). Attach Tooling (B) to the side of cylinder head (25) that is near the turbocharger. The weight of cylinder head (25) is approximately 365 kg (800 lb). 16. Remove bolts (26) and bolts (27). 17. Remove cylinder head (25). Remove the gaskets, O-ring seals, and the spacer plate. i02446286

Cylinder Head - Install Illustration 199

g01148516

11. Remove bolts (17). Remove sealing plate (18) and adapter assembly (19).

SMCS Code: 1100-012


Required Tools Tool

Part Number

Part Description

Qty

A

138-7573

Link Bracket

3

B

1U-9200

Lever Puller Hoist

1

C

4c-5593

Anti-Seize Compound

1


Illustration 200

g01148522


12. Disconnect clip assembly (22) from the cylinder head. Remove tube assemblies (21). 13. Remove bracket (20). 14. Disconnect tube assembly (23) and remove tube assembly (24).

Illustration 202

Illustration 201

g01148568

g01148568

RENR9716-02


g01148791

Illustration 203

1. Install the gaskets, O-ring seals, and the spacer plate on the engine. 2. Attach Tooling (A) and a suitable lifting device to cylinder head (25). Attach Tooling (B) to the side of cylinder head (25) that is near the turbocharger. The weight of cylinder head (25) is approximately 365 kg (800 lb). 3. Position cylinder head (25) on the dowel pins in the cylinder block. Note: Apply Tooling (C) to the bolt threads and both sides of the washers. Tighten the bolts in the following step sequence: 4. Install bolts (26) and bolts (27) according to the following procedure. a. In a numerical sequence, tighten Bolt (1) through Bolt (26) to a torque of 270 ± 15 N·m (199 ± 11 lb ft). b. In a numerical sequence, tighten Bolt (1) through Bolt (26) to a torque of 450 ± 15 N·m (332 ± 11 lb ft).

Illustration 204

g01148522

5. Connect tube assembly (23) and install tube assembly (24). 6. Install bracket (20). 7. Connect clip assembly (22). Install tube assemblies (21).

c. In a numerical sequence, again tighten Bolt (1) through Bolt (26) to a torque of 450 ± 15 N·m (332 ± 11 lb ft). d. In a numerical sequence, tighten Bolt (27) through Bolt (39) to a torque of 45 ± 7 N·m (33 ± 5 lb ft).

Illustration 205

g01148516


RENR9716-02

8. Install adapter assembly (19) and sealing plate (18). Install bolts (17).

11. Install bracket (14). 12. Connect harness assembly (13) and harness assembly (12). 13. Install cover (10) and elbow (11).

Illustration 206

g01148492

Illustration 209

g01148246

14. Connect hose assembly (9). Install elbow (8).

Illustration 207

g01151441

9. Install damper (16) and bolts (15). 10. Tighten the bolts to a torque of 240 ± 40 N·m (177 ± 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.

Illustration 210

g01222314

15. Install new O-ring seals and sealing plate (7).

Illustration 211

g01222233

16. Install adapter assembly (6), thrust plate (5), and bolts (4). Illustration 208

g01148489

RENR9716-02


End By: a. Install the fuel transfer pump. Refer to Disassembly and Assembly, “Fuel Transfer Pump - Install”. b. Install the valve mechanism cover base. Refer to Disassembly and Assembly, “Valve Mechanism Cover Base - Remove and Install”. c. Install the electronic unit injectors. Refer to Disassembly and Assembly, “Electronic Unit Injector - Install”.

Illustration 212

g01222230

i02446397

Camshaft - Remove SMCS Code: 1210-011


Required Tools

Illustration 213

Tool

Part Number

A

177-8001

Pilot Sleeve

2

B

249-2936

Adapter

1

C

274-7932(1) or 274-7933(2)

Guide

1

g01151468 (1)

17. Install gear (3) and bolts (2).

(2)

18. Tighten the bolts to a torque of 240 ± 40 N·m (177 ± 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.

Part Description

Qty

Front Removal Rear Removal

Start By: a. Remove the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, “Rocker Arm and Shaft - Remove”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 214

g01222228

NOTICE Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.

19. Install cover (1). 20. Fill the cooling system. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

NOTICE Care must be used when removing or installing the camshaft. Do not damage the finshed surfaces of the camshaft or the camshaft bearings.


RENR9716-02

1. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

Illustration 218

g01222234

5. Use bolt (4) in order to remove sealing plate (7). Remove the O-ring seals. Illustration 215

g01222228

2. Remove cover (1).

Illustration 219

g01160256

6. Remove elbow (9) and cover (8). Illustration 216

g01222230

3. Remove bolts (2) and gear (3).

Illustration 220

7. Remove bolts (10) and damper (11). Illustration 217

g01222233

4. Remove bolts (4), thrust plate (5), and adapter assembly (6).

g01160259

RENR9716-02


Note: Rotate the camshaft during removal. This will prevent the camshaft from binding in the camshaft bearings. i02446568

Camshaft - Install SMCS Code: 1210-012

Installation Procedure Table 51 Illustration 221

Required Tools

g01160261

8. Remove bolts (12). Remove sealing plate (13) and adapter assembly (14).

Tool

Part Number

A

177-8001

Pilot Sleeve

2

B

249-2936

Adapter

1

Guide

1

Lubricant

1

9.

(1) (2)

274-7932(1)

C

or 274-7933(2)

D

8T-2998

Part Description

Qty

Front Removal Rear Removal

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 222

g01160265

10. Install Tooling (A) and Tooling (B) on the rear of camshaft (15). Install Tooling (A) on the front of camshaft (15). 11. Install Tooling (C) on the front housing or the rear housing. Tooling (C) is used to support the camshaft. Note: It is necessary to install Tooling (A) and Tooling (B) on the camshaft. Tooling (A) and Tooling (B) will support the camshaft as the camshaft is moved out of the cylinder head and into Tooling (C). Align the camshaft with the bore of Tooling (C). Note: Avoid lifting the camshaft. The camshaft should rest on Tooling (A) and Tooling (B). Lifting of the camshaft can cause misalignment as the camshaft is removed, resulting in damage to the camshaft bearings. 12. Carefully slide the camshaft out of the cylinder head for removal. Use two technicians to remove the camshaft. Keep the camshaft level while the camshaft is being removed from the cylinder head. The weight of the camshaft is approximately 35 kg (77 lb).

NOTICE Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. NOTICE Care must be used when removing or installing the camshaft. Do not damage the finshed surfaces of the camshaft or the camshaft bearings. 1. Ensure that the camshaft and camshaft bearings are thoroughly clean. Lubricate the camshaft lobes with a 50/50 mixture of Tooling (D) and clean engine oil. Apply a thin coat of clean engine oil on the camshaft bearings.


Illustration 223

RENR9716-02

g01160265

Illustration 225

g01160259

Illustration 226

g01151441

2. Install Tooling (A) and Tooling (B) on the rear of camshaft (15). Install Tooling (A) on the front of camshaft (15). 3. Install Tooling (C) on the front housing or the rear housing. Tooling (C) is used to support the camshaft. 4. Use two technicians to install the camshaft. Use Tooling (C) to assist in aligning the camshaft with the camshaft bearings. Carefully slide the camshaft into the cylinder head. Keep the camshaft level while the camshaft is being installed in the cylinder head. The weight of the camshaft is approximately 35 kg (77 lb). Note: Rotate the camshaft during installation. This will prevent the camshaft from binding in the camshaft bearings. 5. Remove Tooling (A) and Tooling (B) from the camshaft.

7. Install damper (11) and bolts (10). 8. Tighten the bolts to a torque of 240 ± 40 N·m (177 ± 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.


g01160261

6. Install adapter assembly (14) and sealing plate (13). Install bolts (12).

9. Install cover (8) and elbow (9).

g01160256

RENR9716-02

Illustration 228


g01222314

10. Install new O-ring seals and sealing plate (7).

Illustration 231

g01151468

12. Install gear (3) and bolts (2). 13. Tighten the bolts to a torque of 240 ± 40 N·m (177 ± 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.

Illustration 229

g01222233

11. Install adapter assembly (6), thrust plate (5), and bolts (4). Illustration 232

g01222228

14. Install cover (1). 15. Fill the cooling system. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”. End By: a. Install the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, “Rocker Arms and Shaft - Install”. Illustration 230

g01222230


RENR9716-02

i02451045

Camshaft Bearings - Remove SMCS Code: 1211-011

4. Use Tooling (A) to remove camshaft bearing (1) from the cylinder head.

Removal Procedure

5. Remove Tooling (B) from Tooling (A) and remove the camshaft bearing.

Table 52

Required Tools Tool

Part Number

A

B C

Part Description

Note: Tooling (C) is installed on the outside of the cylinder head. Tooling (C) is required in order to remove all the camshaft bearings from the cylinder head.

Qty i02451063

8S-2241

Camshaft Bearing Tool Group

1

9U-7222

Camshaft Bearing Pilot

1

8M-8778

Taperlock Stud 1/2 - 13 by 1 9/16 inch

1

9U-7210

Puller Plate

1

Camshaft Bearings - Install SMCS Code: 1211-012


Required Tools

Start By: a. Remove the camshaft. Refer to Disassembly and Assembly, “Camshaft - Remove”.

Tool

Part Number

Part Description

Qty

A

8S-2241

Camshaft Bearing Tool Group

1

9U-7222

Camshaft Bearing Pilot

1

8M-8778

Taperlock Stud 1/2 - 13 by 1 9/16 inch

1


B


C

9U-7210

Puller Plate

1

D

9U-7223

Alignment Bushing

1

9U-7213

Backup Plate

1

0S-1621

Bolt 1/2 - 13 by 1 inch

1

9U-7214

Spacer Plate

1

E F

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 233

g01159745

1. Remove the No. 7 camshaft bearing (rear). Work from the rear of the engine to the front of the engine. 2. Install the small end of Tooling (B) in camshaft bearing (1). 3. Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B). Illustration 234

g01159754

RENR9716-02


1. Install the No. 7 camshaft bearing (rear), as follows: a. Insert the large end of Tooling (B) into the No. 7 camshaft bore.

Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.

b. Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B). c. Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B). Note: Refer to Specifications, “Cylinder Head” for appropriate information for the orientation of the camshaft bearings in the cylinder head. d. Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore. Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.

Illustration 236

g01159758

3. Install the No. 1 camshaft bearing (front), as follows: a. Insert the large end of Tooling (B) into the No. 1 camshaft bore. Assemble Tooling (A) and Tooling (D) on Tooling (B). b. Position camshaft bearing (1) on Tooling (B). Install Tooling (E) and Tooling (F) on Tooling (B). Note: Refer to Specifications, “Cylinder Head” for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.

Illustration 235

g01159756

2. Install the No. 6 through No. 2 camshaft bearings, as follows: a. Insert the large end of Tooling (B) into the camshaft bore. Note: Use Tooling (D) to align Tooling (A) and Tooling (B) with the camshaft bearing bores. Install Tooling (D) in the inside diameter of any installed camshaft bearing between Tooling (A) and Tooling (B). b. Install Tooling (A) on Tooling (B). Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B). Note: Refer to Specifications, “Cylinder Head” for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head. c. Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore.

Note: Tooling (F) is used to seat the No. 1 camshaft bearing to the correct depth in the camshaft bore. c. Use Tooling (A) in order to pull the No. 1 camshaft bearing into the No. 1 camshaft bore. When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed. End By: a. Install the camshaft. Refer to Disassembly and Assembly, “Camshaft - Install”.


RENR9716-02

i02447352

Engine Oil Pan - Remove and Install

2. Remove tube assemblies (1) from engine oil pan (3).

SMCS Code: 1302-010

3. Use Tooling (A) to support engine oil pan (3). The weight of engine oil pan (3) is approximately 25 kg (55 lb).

Removal Procedure

4. Remove bolts (2). Remove engine oil pan (3) and the gasket.

Table 54


Required Tools Tool

Part Number

A

1U-7505

Table 55

Part Description Hydraulic Jack

Qty

Required Tools

1

NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Tool

Part Number

A

1U-7505

Part Description Hydraulic Jack

Qty 1


Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Engine Oil and Filter Change”.

Illustration 238

g01222524

1. Use Tooling (A) to support engine oil pan (3). The weight of engine oil pan (3) is approximately 25 kg (55 lb). 2. Position the gasket and engine oil pan (3) on the engine. Install bolts (2). Note: If the oil drain plugs were removed, install the oil drain plugs. Tighten the oil drain plugs to a torque of 80 ± 10 N·m (59 ± 7 lb ft). 3. Install tube assemblies (1) on engine oil pan (3). 4. Fill the engine with engine oil to the correct level. Refer to Operation and Maintenance Manual, “Engine Oil and Filter - Change”.

Illustration 237

g01222524

RENR9716-02


i02294951

Cylinder Liner - Remove SMCS Code: 1216-011


Required Tools Tool

Part Number

Part Description

Qty

A

5P-8665(1)

Cylinder Liner Puller Gp

1

(1)

The 6V-9448 Cylinder Pack Puller is an optional Tool for removing the cylinder liner.

Start By: a. Remove the pistons and connecting rods. Refer to Disassembly and Assembly, “Pistons and Connecting Rods - Remove”. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates.

g01149417

Illustration 239

1. Use Tooling (A) to remove cylinder liner (1). 2. Remove liner seals (3) and filler band (2) from cylinder liner (1). i02294960

Cylinder Liner - Install SMCS Code: 1216-012


Required Tools


Tool

Part Number

Part Description

Qty

B

2P-8260

Cylinder Liner Installer

1

C

5P-3975

Rubber Lubricant

1

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Check the cylinder liner projection. Refer to Testing and Adjusting, “Cylinder Liner Projection - Inspect”.


RENR9716-02

Start By: a. Remove the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Remove”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

g01149469

Illustration 240

2. Install liner seals (3) on cylinder liner (1). 3. Apply Tooling (C) on the cylinder block liner bore surfaces and liner seals (3). 4. Dip filler band (2) in clean engine oil for a moment. Install the filler band on the cylinder liner immediately. 5. Use Tooling (B) to install cylinder liner (1) in the cylinder block. Ensure that any marks in relation to the cylinder liner projection are in alignment.

g01149484

Illustration 241

1. Use Tooling (A) to rotate the crankshaft in order to gain access to the piston cooling jet. 2. Remove bolt (1) and piston cooling jet (2).


End By:

Required Tools

a. Install the pistons and connecting rods. Refer to Disassembly and Assembly, “Pistons and Connecting Rods - Install”. i02295020

Piston Cooling Jets - Remove and Install SMCS Code: 1331-010


Required Tools Tool

Part Number

A

9S-9082

Part Description Engine Turning Tool

Qty 1

Tool

Part Number

A

9S-9082


Qty 1


RENR9716-02


g01149484

Illustration 242

Illustration 243

g01149594

1. Use Tooling (A) to rotate the crankshaft in order to gain access to the piston cooling jet.

1. Use Tooling (A) to rotate the crankshaft until the piston is at the bottom center.

2. Position piston cooling jet (2) in the cylinder block. Install bolt (1). Tighten the bolt to a torque of 25 ± 6 N·m (18 ± 4 lb ft).

2. Remove the carbon ridge from the top inside surface of the cylinder liner.

End By: a. Install the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Install”. i02295112

Pistons and Connecting Rods - Remove SMCS Code: 1225-011

3. Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary. Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod assembly could cause the connecting rod to fracture. 4. Remove bolts (1) and connecting rod bearing cap (2).


Required Tools Tool

Part Number

A

9S-9082


Qty 1

Start By: a. Remove the cylinder head. Refer to Disassembly and Assembly, “Cylinder Head - Remove”. b. Remove the piston cooling jets. Refer to Disassembly and Assembly, “Piston Cooling Jets - Remove and Install”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 244

g01149595

5. Remove piston (3) and the connecting rod from the cylinder liner.


RENR9716-02

i02447789

Pistons and Connecting Rods - Disassemble SMCS Code: 1225-015

3. Use Tooling (A) to remove pin retainers (5) from piston body assembly (4). 4. Remove connecting rod pin (7) and connecting rod (6) from the piston body assembly.


5. Use Tooling (B) to remove top piston ring (1), intermediate piston ring (2), and oil control piston ring (3) from the piston body assembly.

Table 61

Required Tools Tool

Part Number

A

6V-6192

Pliers

1

B

7B-7974

Piston Ring Expander Gp

1

Part Description

2. Remove upper connecting rod bearing (8) from connecting rod (6).

Qty

i02447828

Pistons and Connecting Rods - Assemble

Start By:

SMCS Code: 1225-016

a. Remove the pistons and connecting rods. Refer to Disassembly and Assembly, “Pistons and Connecting Rods - Remove”.

Assembly Procedure

Note: Mark the components of each piston and connecting rod assembly. The components must be reinstalled in the original location. Do not interchange components. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Table 62

Required Tools Tool

Part Number

A

6V-6192

Pliers

1

B

7B-7974

Piston Ring Expander Gp

1

Part Description

Qty

Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 245

g01222629

1. Remove lower connecting rod bearing (9) from connecting rod bearing cap (10).

RENR9716-02


Note: Ensure that the bearing locking tab is located in the notch of the connecting rod bearing cap. 10. Ensure that the dowels are installed in the connecting rod bearing cap. End By: a. Install the pistons and connecting rods. Refer to Disassembly and Assembly, “Pistons and Connecting Rods - Install”. i02630922

Pistons and Connecting Rods - Install SMCS Code: 1225-012

Illustration 246

g01222629


1. Position the spring for the oil control piston ring in the oil ring groove in the piston body assembly. 2. Position oil control piston ring (3) over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring. Install the oil control piston ring on the piston with Tooling (B). 3. Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification “UP-2” toward the top of the piston. 4. Use Tooling (B) to install top piston ring (1) with the side that has the identification “UP-1” toward the top of the piston. 5. Position top piston ring (1), intermediate piston ring (2), and oil control piston ring (3) so the gaps are 120 degrees from each other. 6. Check the clearance between the ends of top piston ring (1), intermediate piston ring (2), and oil control piston ring (3). Refer to Specifications, “Pistons And Rings”. 7. Position piston body assembly (4) on connecting rod (6). Apply clean engine oil to connecting rod pin (7) and install the connecting rod pin. Install pin retainers (5) with Tooling (A). 8. Install upper connecting rod bearing (8) in connecting rod (6). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod. 9. Install lower connecting rod bearing (9) in connecting rod bearing cap (10).

Required Tools Tool

Part Number

A

9S-9082

Engine Turning Tool

1

B

200-3914

Piston Ring Compressor

1

C

8T-3052

Degree Wheel

1

Part Description

Qty

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, “Bearing Clearance Check”. Apply clean engine oil on the connecting rod bearings for final assembly. 1. Apply clean engine oil to the cylinder liner bore, to the piston rings, and to the outer surface of the piston. Note: Ensure that the connecting rod and pistons are installed in the correct cylinder.


RENR9716-02

Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side opposite of the piston cooling jet. 8. Lubricate the threads of bolts (1) with clean engine oil. Install the bolts. 9. Tighten bolts (1), as follows: a. Tighten Bolt (A) and Bolt (C) to a torque of 70 ± 4 N·m (52 ± 3 lb ft). Illustration 247

g01149650

2. Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center. 3. Use Tooling (B) to install piston (3) and the connecting rod in the cylinder liner. Note: Install the connecting rod so that the bearing tab is located on the opposite side of the piston cooling jet. 4. Install the upper connecting rod bearing in the connecting rod.

b. Tighten Bolt (B) and Bolt (D) to a torque of 70 ± 4 N·m (52 ± 3 lb ft). c. Turn Bolt (B) and Bolt (D) for an additional 60 ± 5 degrees (1/6 turn). Note: If Tooling (C) is not used, place an index mark on each bolt. d. Tighten Bolt (A) and Bolt (C) again to a torque of 70 ± 4 N·m (52 ± 3 lb ft). e. Turn Bolt (A) and Bolt (C) for an additional 60 ± 5 degrees (1/6 turn).

Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.

Note: If Tooling (C) is not used, place an index mark on each bolt.

5. Pull the connecting rod onto the crankshaft journal.

f. Rotate the crankshaft in order to ensure that the crankshaft turns freely.

6. Install the lower connecting rod bearing in the connecting rod bearing cap. Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.

End By: a. Install the piston cooling jets. Refer to Disassembly and Assembly, “Piston Cooling Jets - Remove and Install”. b. Install the cylinder head. Refer to Disassembly and Assembly, “Cylinder Head - Install”. i02295567

Connecting Rod Bearings Remove SMCS Code: 1219-011

Removal Procedure Table 64 Illustration 248

g01149651

7. Position connecting rod bearing cap (2) on the connecting rod.

Required Tools Tool

Part Number

A

9S-9082


Qty 1

RENR9716-02


Start By:

i02295910

a. Remove the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Remove”.

Connecting Rod Bearings Install SMCS Code: 1219-012




Table 65

Required Tools Tool

Part Number

A

9S-9082

Engine Turning Tool

1

B

8T-3052

Degree Wheel

1

Part Description

Qty


Illustration 249

g01149594

1. Use Tooling (A) to rotate the crankshaft until the connecting rod is at the bottom center.

Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, “Bearing Clearance Check”. Apply clean engine oil on the connecting rod bearings for final assembly.

2. Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary. Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod assembly could cause the connecting rod to fracture. 3. Remove bolts (1) and connecting rod bearing cap (2) from the connecting rod. 4. Remove the lower half of the connecting rod bearing from the connecting rod bearing cap. 5. Push the connecting rod away from the crankshaft. Remove the upper half of the connecting rod bearing from the connecting rod.

Illustration 250

g00998730

1. Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center. 2. Install a new lower half connecting rod bearing (3) in connecting rod bearing cap (2). Note: Ensure that bearing locking tab (4) is located in the notch of the connecting rod bearing cap. 3. Install a new upper half connecting rod bearing in the connecting rod. Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.


RENR9716-02

4. Pull the connecting rod onto the crankshaft.

i02296017

Crankshaft Main Bearings Remove SMCS Code: 1203-011


Required Tools

Illustration 251

Tool

Part Number

A

2P-5518

Part Description Bearing Tool

Qty 1

g01149651

5. Position connecting rod bearing cap (2) on the connecting rod. Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side opposite of the piston cooling jet. 6. Lubricate the threads of bolts (1) with clean engine oil. Install the bolts. 7. Tighten bolts (1), as follows: a. Tighten Bolt (A) and Bolt (C) to a torque of 70 ± 4 N·m (52 ± 3 lb ft).

Start By: a. Remove the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Remove”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Check the main bearing caps for identification of the location and check the direction of the main bearing caps in relation to the cylinder block. The main bearing caps must be installed in the original location and the original direction.

b. Tighten Bolt (B) and Bolt (D) to a torque of 70 ± 4 N·m (52 ± 3 lb ft). c. Turn Bolt (B) and Bolt (D) for an additional 60 ± 5 degrees (1/6 turn). Note: If Tooling (B) is not used, place an index mark on each bolt. d. Tighten Bolt (A) and Bolt (C) again to a torque of 70 ± 4 N·m (52 ± 3 lb ft). e. Tighten Bolt (A) and Bolt (C) for an additional 60 ± 5 degrees (1/6 turn). Illustration 252

Note: If Tooling (B) is not used, place an index mark on each bolt. f. Rotate the crankshaft in order to ensure that the crankshaft turns freely. End By: a. Install the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Install”.

g01149949

2. Remove bolts (1) and bolts (3) from No. 2 through No. 6 main bearing caps (2). Note: Remove No. 1 and No. 7 main bearing caps (2) after No. 2 through No. 6 main bearing caps have been installed.

RENR9716-02


Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, “Bearing Clearance - Check”. Apply clean engine oil on the main bearings for final assembly. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.

g01149952

Illustration 253

3. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to remove upper main bearing (4) from the cylinder block. Note: Push the upper main bearing from the opposite side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft. 4. Remove the thrust plates from each side of the No. 4 main bearing. 5. Remove the lower halves of the main bearings from the main bearing caps. i02296049

Crankshaft Main Bearings Install SMCS Code: 1203-012

g01149952

1. Position new upper main bearing (4) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block. Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft. 2. Install the thrust plates on each side of the No. 4 main bearing.


Note: Install the thrust plates with the words “Block Side” toward the cylinder block.

Table 67

Required Tools Part Description

Illustration 254

Tool

Part Number

Qty

A

2P-5518

Bearing Tool

1

B

8T-5096

Dial Indicator

1

C

8T-3052

Degree Wheel

1


3. Install the lower halves of the crankshaft main bearings in the main bearing caps. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.


RENR9716-02

Note: Bolt (C) is on the bearing tab side of the main bearing cap. g. Rotate the crankshaft in order to ensure that the crankshaft turns freely. 7. Use Tooling (B) to check the crankshaft end play. Ensure that Tooling (B) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center). Crankshaft end play (new thrust plates) ...... 0.10 to 0.60 mm (0.004 to 0.024 inch) Illustration 255

g01149987

4. Position main bearing caps (2) on the crankshaft. Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the “FRONT” on the main bearing cap is installed toward the front of the cylinder block. 5. Lubricate the threads of bolts (1) and bolts (3) with clean engine oil. Install the bolts. 6. Tighten bolts (1) and bolts (3) for the main bearing caps, as follows: a. Tighten Bolt (A) to a torque of 258 ± 14 N·m (190 ± 10 lb ft). Note: Bolt (A) is on the bearing tab side of the main bearing cap.

End By: a. Install the engine oil pump. Refer to Disassembly and Assembly, “Engine Oil Pump - Install”. i02296738

Crankshaft - Remove SMCS Code: 1202-011


Required Tools Tool

Part Number

A

138-7574

b. Tighten Bolt (B) to a torque of 258 ± 14 N·m (190 ± 10 lb ft). Note: Bolt (B) is on the opposite side of the bearing tab of the main bearing cap. c. Tighten Bolt (B) for an additional 120 ± 5 degrees (2 flats).

B

Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap. d. Tighten Bolt (A) for an additional 120 ± 5 degrees (2 flats). Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap. e. Tighten Bolt (D) to a torque of 80 ± 10 N·m (59 ± 7 lb ft). Note: Bolt (D) is on the opposite side of the bearing tab of the main bearing cap. f. Tighten Bolt (C) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).

C

Part Description

Qty

Link Bracket

2

1H-3110

Bearing Puller

1

8B-7560

Step Plate

1

9U-6600

Hand Hydraulic Pump

1

1H-3108

Push-Puller Leg

2

1H-3107

Bearing Puller

1

3H-0468

Puller Plate

5

3H-0465

Push-Puller Plate

2

1P-0820

Hydraulic Puller

1

5B-0637

Nut

1

8S-6586

Forcing Screw

1

5P-0944

Dowel Puller Group

1

5P-0939

Dowel Extractor

1

Start By: a. Remove the front housing. Refer to Disassembly and Assembly, “Housing (Front) - Remove”. b. Remove the rear housing. Refer to Disassembly and Assembly, “Housing (Rear) - Remove”.

RENR9716-02


c. Remove the piston cooling jets. Refer to Disassembly and Assembly, “Piston Cooling Jets - Remove and Install”. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

6. Remove crankshaft (6) from the cylinder block. 7. Remove the thrust plates from each side of the No. 4 main bearing. 8. Remove the lower main bearings from main bearing caps (4). Remove the upper main bearings from the cylinder block.

1. Check the main bearing caps for identification for the location and the direction in the cylinder block. The identification marks on the main bearing caps must be installed in the same direction prior to removal. 2. Check the connecting rod and the connecting rod bearing caps for identification and the location in the cylinder block.

Illustration 258

g01150282

9. Use Tooling (B) to remove crankshaft gear (7) from crankshaft (6).

Illustration 256

g01150281

3. Remove bolts (1). Remove connecting rod bearing caps (2).

Illustration 259

g01150284

10. If necessary, use Tooling (C) to remove dowel (8) and dowel (9) from crankshaft (6).

Illustration 257

g01150289

4. Remove bolts (3) and bolts (5). Remove main bearing caps (4). 5. Install Tooling (A) and a suitable lifting device on each end of crankshaft (6). The weight of crankshaft (6) is approximately 188 kg (415 lb).


RENR9716-02

i02296800

Crankshaft - Install SMCS Code: 1202-012

Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.


Required Tools Tool

Part Number

A

138-7574

Link Bracket

2

D

8T-5096

Dial Indicator

1

E

8T-3052

Degree Wheel

1

Part Description

Qty


Illustration 261


g01150344

5. Install Tooling (A) and a suitable lifting device on each end of crankshaft (6). The weight of crankshaft (6) is approximately 188 kg (415 lb). 6. Install crankshaft (6) with Timing Mark “V” on the crankshaft gear in alignment with Timing Mark “V” on the cluster gear. 7. Install the thrust plates on each side of the No. 4 main bearing. Note: Install the thrust plates with the words “Block Side” toward the cylinder block. 8. Install the lower halves of the crankshaft main bearings in the main bearing caps.

Illustration 260

g01150312

1. Install dowel (8) in the crankshaft. Protrusion of dowel (8) from the crankshaft face ........................................ 8.4 mm (0.33 inch) 2. Install dowel (9) in the crankshaft. Protrusion of dowel (9) from the crankshaft ............................ 4.1 ± 0.5 mm (0.16 ± 0.02 inch) 3. Install crankshaft gear (7) on the crankshaft with the keyway in alignment with dowel (9). Timing Mark “V” of the gear should face away from crankshaft (6). Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, “Bearing Clearance - Check”. Apply clean engine oil on the main bearings for final assembly. 4. Install the upper halves of the main bearings in the cylinder block.

Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the main bearing cap. 9. Position main bearing caps (4) on the crankshaft. Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the “FRONT” on the main bearing cap is installed toward the front of the cylinder block. 10. Lubricate the threads of bolts (3) and bolts (5) with clean engine oil. Install the bolts. 11. Tighten bolts (3) and bolts (5) for the main bearing caps, as follows: a. Tighten Bolt (A) to a torque of 258 ± 14 N·m (190 ± 10 lb ft). Note: Bolt (A) is on the bearing tab side of the main bearing cap. b. Tighten Bolt (B) to a torque of 258 ± 14 N·m (190 ± 10 lb ft).

RENR9716-02


Note: Bolt (B) is on the opposite side of the bearing tab of the main bearing cap. c. Tighten Bolt (B) for an additional 120 ± 5 degrees (2 flats). Note: If Tooling (E) is not used, place an index mark on the bolt and the main bearing cap. d. Tighten Bolt (A) for an additional 120 ± 5 degrees (2 flats).

Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side opposite of the piston cooling jet. 14. Lubricate the threads of bolts (1) with clean engine oil. Install the bolts. 15. Tighten bolts (1), as follows:

Note: If Tooling (E) is not used, place an index mark on the bolt and the main bearing cap.

a. Tighten Bolt (A) and Bolt (C) to a torque of 70 ± 4 N·m (52 ± 3 lb ft).

e. Tighten Bolt (D) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).

b. Tighten Bolt (B) and Bolt (D) to a torque of 70 ± 4 N·m (52 ± 3 lb ft).

Note: Bolt (D) is on the opposite side of the bearing tab of the main bearing cap. f. Tighten Bolt (C) to a torque of 80 ± 10 N·m (59 ± 7 lb ft). Note: Bolt (C) is on the bearing tab side of the main bearing cap. g. Rotate the crankshaft in order to ensure that the crankshaft turns freely. 12. Use Tooling (D) to check the crankshaft end play. Ensure that Tooling (D) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center). Crankshaft end play (new thrust plates) ...... 0.10 to 0.60 mm (0.004 to 0.024 inch) Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, “Bearing Clearance Check”. Apply clean engine oil on the connecting rod bearings for final assembly.

c. Turn Bolt (B) and Bolt (D) for an additional 60 ± 5 degrees (1/6 turn). Note: If Tooling (E) is not used, place an index mark on each bolt and connecting rod cap. d. Tighten Bolt (A) and Bolt (C) again to a torque of 70 ± 4 N·m (52 ± 3 lb ft). e. Turn Bolt (A) and Bolt (C) for an additional 60 ± 5 degrees (1/6 turn). Note: If Tooling (E) is not used, place an index mark on each bolt and connecting rod cap. f. Rotate the crankshaft in order to ensure that the crankshaft turns freely. End By: a. Install the piston cooling jets. Refer to Disassembly and Assembly, “Piston Cooling Jets - Remove and Install”. b. Install the rear housing. Refer to Disassembly and Assembly, “Housing (Rear) - Install”. c. Install the front housing. Refer to Disassembly and Assembly, “Housing (Front) - Install”.

Illustration 262

g01150364

13. Position the connecting rod against the crankshaft. Install connecting rod bearing cap (2) on the connecting rod.


RENR9716-02

i02717761

Bearing Clearance - Check

• Ensure that the backs of the bearings and the

SMCS Code: 1203-535; 1219-535

bores are clean and dry.

Measurement Procedure

• Ensure that the bearing locking tabs are properly seated in the tab grooves.

Table 70

• The crankshaft must be free of oil at the contact

Required Tools Tool

Part Number 198-9142

points of Tooling (A).

Qty

1. Put a piece of Tooling (A) on the crown of the bearing that is in the cap.

Plastic Gauge (Green) 0.025 to 0.076 mm (0.001 to 0.003 inch)

1

Plastic Gauge (Red) 0.051 to 0.152 mm (0.002 to 0.006 inch)

1

198-9144

Plastic Gauge (Blue) 0.102 to 0.229 mm (0.004 to 0.009 inch)

1

2. Use the correct torque-turn specifications in order to install the bearing cap. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.

198-9145

Plastic Gauge (Yellow) 0.230 to 0.510 mm (0.009 to 0.020 inch)

1

Note: Do not turn the crankshaft when Tooling (A) is installed.

198-9143 A

Part Description

The technician must be very careful to use Tooling (A) correctly. The following points must be remembered:

Note: Plastic gauge may not be necessary when the engine is in the chassis.

Note: Do not allow Tooling (A) to extend over the edge of the bearing.

3. Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling (A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration 263.

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: Caterpillar does not recommend the checking of the actual bearing clearances particularly on small engines. This is because of the possibility of obtaining inaccurate results and the possibility of damaging the bearing or the journal surfaces. Each Caterpillar engine bearing is quality checked for specific wall thickness. Note: The measurements should be within specifications and the correct bearings should be used. If the crankshaft journals and the bores for the block and the rods were measured during disassembly, no further checks are necessary. However, if the technician still wants to measure the bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals with small diameters if clearances are less than 0.10 mm (0.004 inch). NOTICE Lead wire, shim stock or a dial bore gauge can damage the bearing surfaces.

Illustration 263

g01152855

Typical Example

4. Remove all of Tooling (A) before you install the bearing cap.

RENR9716-02


Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all parts of Tooling (A) are not the same width. Measure the major width in order to ensure that the parts are within the specification range. Refer to Specifications Manual, “Connecting Rod Bearing Journal” and Specifications Manual, “Main Bearing Journal” for the correct clearances. i02449735

Atmospheric Pressure Sensor - Remove and Install g01222887

SMCS Code: 1923-010

Illustration 265

Removal Procedure

1. Install a new O-ring seal on atmospheric pressure sensor (1).


2. Install atmospheric pressure sensor (1) and tighten to a torque of 10 ± 2 N·m (90 ± 18 lb in).


3. Connect harness assembly (2). i02297743

Camshaft Position Sensor Remove and Install SMCS Code: 1912-010

Removal Procedure

Illustration 264

g01222887

1. Disconnect harness assembly (2). 2. Remove atmospheric pressure sensor (1) from the adapter on the cylinder block. 3. Remove the O-ring seal from atmospheric pressure sensor (1).


NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.


RENR9716-02

i02297803

Crankshaft Position Sensor Remove and Install SMCS Code: 1912-010

Removal Procedure

Illustration 266

g01150693

1. Disconnect harness assembly (3). 2. Remove bolt (1) and camshaft position sensor (2). 3. Remove the O-ring seal from camshaft position sensor (2).

NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products.







Illustration 267

g01150693

1. Install a new O-ring seal on camshaft position sensor (2). Lubricate the O-ring seal with clean engine oil. 2. Position camshaft position sensor (2) in the front housing and install bolt (1). Tighten bolt (1) to a torque of 28 ± 7 N·m (21 ± 5 lb ft). 3. Connect harness assembly (3).

Illustration 268

g01150731

1. Disconnect harness assembly (1). 2. Remove bolt (3) and crankshaft position sensor (2). 3. Remove the O-ring seal from crankshaft position sensor (2).

RENR9716-02




Contaminants may cause rapid wear and shortened component life. 1. Drain the coolant from the cooling system to a level below the coolant temperature sensor into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.

Illustration 269

g01150731

1. Install a new O-ring seal on crankshaft position sensor (2). Lubricate the O-ring seal with clean engine oil. 2. Install crankshaft position sensor (2) in the front housing. Install bolt (3). Tighten bolt (3) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).

Illustration 270

g01222981

2. Disconnect harness assembly (1). 3. Remove coolant temperature sensor (2).

3. Connect harness assembly (1). i02449857

Coolant Temperature Sensor Remove and Install

4. Remove the O-ring seal from coolant temperature sensor (2).


SMCS Code: 1906-010


Removal Procedure



Illustration 271

g01222981


RENR9716-02

1. Install a new O-ring seal on coolant temperature sensor (2).

2. Remove engine oil pressure sensor (1) from the adapter on the cylinder block.

2. Install coolant temperature sensor (2) and tighten to a torque of 20 ± 5 N·m (15 ± 4 lb ft).

3. Remove the O-ring seal from engine oil pressure sensor (1).



4. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change”.


i02298137


Engine Oil Pressure Sensor Remove and Install SMCS Code: 1924-010

Removal Procedure NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Illustration 272

1. Disconnect harness assembly (2).

g01150948

Illustration 273

g01150948

1. Install a new O-ring seal on engine oil pressure sensor (1). 2. Install engine oil pressure sensor (1) and tighten to a torque of 10 ± 2 N·m (89 ± 18 lb in). 3. Connect harness assembly (2).

RENR9716-02


i02581037

Fuel Pressure Sensor Remove and Install


SMCS Code: 7414-010

Removal Procedure NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Dealer Service Tool Catalog” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Turn the fuel supply valve to the OFF position.

Illustration 275

g01292812

1. Install a new O-ring seal on fuel pressure sensor (2). 2. Install fuel pressure sensor (2). Tighten fuel pressure sensor (2) to a torque of 10 ± 2 N·m (90 ± 18 lb in). 3. Connect harness assembly (1). 4. Turn the fuel supply valve to the ON position. i02581061

Fuel Temperature Sensor Remove and Install SMCS Code: 1922-010

Removal Procedure

Illustration 274

g01292812

2. Disconnect harness assembly (1). 3. Remove fuel pressure sensor (2) from the fuel filter base. 4. Remove the O-ring seal from fuel pressure sensor (2).



RENR9716-02

2. Install fuel temperature sensor (2). Tighten fuel temperature sensor (2) to a torque of 20 ± 5 N·m (15 ± 4 lb ft).


3. Connect harness assembly (1). 4. Turn the fuel supply valve to the ON position.

1. Turn the fuel supply valve to the OFF position. i02449930

Turbocharger Outlet Pressure Sensor - Remove and Install SMCS Code: 1917-010

Removal Procedure NOTICE Keep all parts clean from contaminants.

Illustration 276

g01292826


2. Disconnect harness assembly (1). 3. Remove fuel temperature sensor (2) from the fuel filter base. 4. Remove the O-ring seal from fuel temperature sensor (2).


Illustration 278

g01223056

1. Disconnect harness assembly (1). 2. Remove turbocharger outlet pressure sensor (2) from the inlet manifold. 3. Remove the O-ring seal from turbocharger outlet pressure sensor (2).


Illustration 277

g01292826

1. Install a new O-ring seal on fuel temperature sensor (2).


RENR9716-02


3. Remove the O-ring seal from inlet air temperature sensor (2).


Illustration 279

g01223056

1. Install a new O-ring seal on turbocharger outlet pressure sensor (2). 2. Install turbocharger outlet pressure sensor (2) and tighten to a torque of 10 ± 2 N·m (90 ± 18 lb in). 3. Connect harness assembly (1). i02449945

Inlet Air Temperature Sensor Remove and Install SMCS Code: 1921-010

Illustration 281

g01223082

1. Install a new O-ring seal on inlet air temperature sensor (2). 2. Install inlet air temperature sensor (2) and tighten to a torque of 20 ± 5 N·m (15± 4 lb ft).

Removal Procedure



i02574366


Belt Guard - Remove and Install SMCS Code: 1357-010-GD

Removal Procedure

Illustration 280

g01223082

1. Disconnect harness assembly (1). 2. Remove inlet air temperature sensor (2) from the inlet manifold.

Illustration 282

g01289708


RENR9716-02

1. Remove bolts (1). Repeat for the opposite side. Remove bottom belt guard (2).

i02755046

Fan Guard - Remove and Install SMCS Code: 1360-010

Removal Procedure

Illustration 283

g01289709

2. Remove bolt (3). Repeat for the opposite side. Remove upper belt guard (4).


Illustration 286

g01289778

1. Remove bolts (1). Remove lower fan guard (2).

Illustration 284

g01289709

1. Install upper belt guard (4). Install bolt (3). Repeat for the opposite side.

Illustration 287

g01379587

2. Remove bolts (3). Remove upper fan guard (4).


Illustration 285

g01289708

2. Install lower belt guard (2). Install bolts (1). Repeat for the opposite side.

Illustration 288

g01379587

1. Install upper fan guard (4). Install bolts (3).

RENR9716-02


g01289778

Illustration 289

2. Install lower fan guard (2). Install bolts (1). i02755088

Fan - Remove and Install

Illustration 291

SMCS Code: 1356-010

2. Remove bolts (2). Remove fan (1).

Removal Procedure


Table 71

Table 72

Required Tools Tool

Part Number

A

140-7742

Part Description Sleeve

g01289733

Required Tools Qty

Tool

Part Number

1

A

140-7742

Part Description Sleeve

Qty 1

Start By: a. Remove the fan guard. Refer to Disassembly and Assembly, “Fan Guard - Remove and Install”.

Illustration 290

g01289730

1. Attach Tooling (A) and a suitable lifting device onto fan (1). The weight of fan (1) is approximately 45 kg (100 lb).

Illustration 292

g01289733

1. Attach Tooling (A) and a suitable lifting device onto fan (1). The weight of fan (1) is approximately 45 kg (100 lb). Install fan (1). Install bolts (2).


Illustration 293

RENR9716-02

g01289730

2. Remove Tooling (A) and the suitable lifting device from fan (1). End By: a. Install the fan guard. Refer to Disassembly and Assembly, “Fan Guard - Remove and Install”.

Illustration 294

g01289585

2. Loosen bolts (1). Loosen locknut (2).

i02574047

Fan Drive - Remove and Install SMCS Code: 1359-010; 1386-010

Removal Procedure Start By: a. Remove the fan. Refer to Disassembly and Assembly, “Fan - Remove and Install”. b. Remove the belt guard. Refer to Disassembly and Assembly, “Belt Guard - Remove and Install”. 1. Remove the belts. Refer to Operation and Maintenance Manual, “Belts Inspect/Adjust/Replace”. Illustration 295

g01289589

3. Attach a suitable lifting device onto fan drive (3). The weight of fan drive (3) is approximately 45 kg (100 lb). Remove bolts (1). Remove fan drive (3).

RENR9716-02



b. Install the fan. Refer to Disassembly and Assembly, “Fan - Remove and Install”. i02417465

Electronic Control Module Remove and Install SMCS Code: 1901-010

Removal Procedure 1. Turn the battery disconnect switch to the “OFF” position. 2. Disconnect the negative battery terminal at the battery.

Illustration 296

g01289589

1. Attach a suitable lifting device onto fan drive (3). The weight of fan drive (3) is approximately 45 kg (100 lb). Install fan drive (3). Install bolts (1).

Illustration 298

g01208278

3. Loosen allen head screw (1). Disconnect the harness assembly from electronic control module (5). 4. Disconnect hose assemblies (2) and (4). Illustration 297

g01289585

2. Install the belts. Refer to Operation and Maintenance Manual, “Belts Inspect/Adjust/Replace”. 3. Tighten bolts (1). Tighten locknut (2). End By: a. Install the belt guard. Refer to Disassembly and Assembly, “Belt Guard - Remove and Install”.

5. Remove bolts (6). Remove electronic control module (5) and ground strap (3). 6. Remove washers (7) and isolation mounts (8) from electronic control module (5).


RENR9716-02


Illustration 300

g01223195

2. Remove V-belt (1) from alternator (3). 3. Disconnect the harness assemblies from alternator (3). Illustration 299

g01208278

1. Position isolation mounts (8) on electronic control module (5). Position the spacers, washers (7), ground strap (3), and electronic control module (5) on the support assemblies. Install bolts (6).

4. Remove bolt (2) and bolt (4). 5. Remove alternator (3) from the mounting group.


2. Connect hose assemblies (4) and (2). 3. Connect the harness assembly to electronic control module (5). Tighten allen head screw (1) to a torque of 6 ± 1 N·m (53 ± 9 lb in). 4. Connect the negative battery terminal at the battery. 5. Turn the battery disconnect switch to the “ON” position. i02450170

Illustration 301

g01223195

Alternator - Remove and Install

1. Position alternator (3) on the mounting group.

SMCS Code: 1405-010

2. Install bolt (4) and bolt (2).

Removal Procedure

3. Connect the harness assemblies to alternator (3). Refer to Specifications, “Alternator and Regulator”.

1. Turn the battery disconnect switch to the OFF position.

4. Install V-belt (1) on alternator (3). 5. Adjust the tension on the V-belt. Refer to Operation and Maintenance Manual, “Belt Inspect/Adjust/Replace”. 6. Turn the battery disconnect switch to the ON position.

RENR9716-02


i02419387


Electric Starting Motor Remove and Install SMCS Code: 1453-010

Removal Procedure

Personal injury can result from failure to disconnect the battery. First, disconnect the negative battery cable. Then, disconnect the positive battery cable. A positive power lead can cause sparks if the battery is not disconnected. Sparks can possibly result in battery explosion or fire. 1. Turn the battery disconnect switch to the “OFF” position.

Illustration 303

g01208927

1. Fasten a suitable lifting device to electric starting motor (1). The weight of electric starting motor (1) is approximately 37 kg (80 lb). 2. Position the gasket and electric starting motor (1) in the flywheel housing. Install bolts (2). 3. Connect the harness assemblies to electric starting motor (1). Refer to Specifications, “Electric Starting Motor”. 4. Turn the battery disconnect switch to the “ON” position.

Illustration 302

g01208927

2. Place an index mark on all of the harness assemblies. Disconnect the harness assemblies from electric starting motor (1). 3. Fasten a suitable lifting device to electric starting motor (1). The weight of electric starting motor (1) is approximately 37 kg (80 lb). 4. Remove bolts (2). 5. Remove electric starting motor (1) and the gasket from the flywheel housing.

106 Index Section

RENR9716-02

Index A Aftercooler - Install................................................. 40 Installation Procedure ........................................ 40 Aftercooler - Remove............................................. 38 Removal Procedure ........................................... 38 Alternator - Remove and Install ........................... 104 Installation Procedure ...................................... 104 Removal Procedure ......................................... 104 Atmospheric Pressure Sensor - Remove and Install ................................................................... 93 Installation Procedure ........................................ 93 Removal Procedure ........................................... 93 B Bearing Clearance - Check ................................... 92 Measurement Procedure ................................... 92 Belt Guard - Remove and Install ........................... 99 Installation Procedure ...................................... 100 Removal Procedure ........................................... 99 C Camshaft - Install................................................... 73 Installation Procedure ........................................ 73 Camshaft - Remove............................................... 71 Removal Procedure ........................................... 71 Camshaft Bearings - Install ................................... 76 Installation Procedure ........................................ 76 Camshaft Bearings - Remove ............................... 76 Removal Procedure ........................................... 76 Camshaft Position Sensor - Remove and Install ... 93 Installation Procedure ........................................ 94 Removal Procedure ........................................... 93 Connecting Rod Bearings - Install ......................... 85 Installation Procedure ........................................ 85 Connecting Rod Bearings - Remove ..................... 84 Removal Procedure ........................................... 84 Coolant Temperature Sensor - Remove and Install ................................................................... 95 Installation Procedure ........................................ 95 Removal Procedure ........................................... 95 Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Install .................................................... 36 Installation Procedure ........................................ 36 Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Remove ................................................ 35 Removal Procedure ........................................... 35 Crankshaft - Install................................................. 90 Installation Procedure ........................................ 90 Crankshaft - Remove............................................. 88 Removal Procedure ........................................... 88 Crankshaft Front Seal - Install ............................... 55 Installation Procedure ........................................ 55 Crankshaft Front Seal - Remove ........................... 54 Removal Procedure ........................................... 54

Crankshaft Main Bearings - Install......................... Installation Procedure ........................................ Crankshaft Main Bearings - Remove..................... Removal Procedure ........................................... Crankshaft Position Sensor - Remove and Install.. Installation Procedure ........................................ Removal Procedure ........................................... Crankshaft Rear Seal - Install................................ Installation Procedure ........................................ Crankshaft Rear Seal - Remove............................ Removal Procedure ........................................... Cylinder Head - Install ........................................... Installation Procedure ........................................ Cylinder Head - Remove ....................................... Removal Procedure ........................................... Cylinder Liner - Install............................................ Installation Procedure ........................................ Cylinder Liner - Remove........................................ Removal Procedure ...........................................

87 87 86 86 94 95 94 50 50 50 50 68 68 66 66 79 79 79 79

D Disassembly and Assembly Section........................ 4 E Electric Starting Motor - Remove and Install ....... 105 Installation Procedure ...................................... 105 Removal Procedure ......................................... 105 Electronic Control Module - Remove and Install.. 103 Installation Procedure ...................................... 104 Removal Procedure ......................................... 103 Electronic Unit Injector - Install .............................. 14 Installation Procedure ........................................ 14 Electronic Unit Injector - Remove .......................... 13 Removal Procedure ........................................... 13 Electronic Unit Injector Sleeve - Install .................. 16 Installation Procedure ........................................ 16 Electronic Unit Injector Sleeve - Remove .............. 15 Removal Procedure ........................................... 15 Engine - Install......................................................... 6 Installation Procedure .......................................... 6 Engine - Remove..................................................... 4 Removal Procedure ............................................. 4 Engine Oil Cooler - Install...................................... 28 Installation Procedure ........................................ 28 Engine Oil Cooler - Remove.................................. 27 Removal Procedure ........................................... 27 Engine Oil Filter Base - Assemble......................... 26 Assembly Procedure.......................................... 26 Engine Oil Filter Base - Disassemble .................... 26 Disassembly Procedure ..................................... 26 Engine Oil Filter Base - Install ............................... 27 Installation Procedure ........................................ 27 Engine Oil Filter Base - Remove ........................... 25 Removal Procedure ........................................... 25

RENR9716-02

Engine Oil Pan - Remove and Install..................... Installation Procedure ........................................ Removal Procedure ........................................... Engine Oil Pressure Sensor - Remove and Install.. Installation Procedure ........................................ Removal Procedure ........................................... Engine Oil Pump - Assemble................................. Assembly Procedure.......................................... Engine Oil Pump - Disassemble............................ Disassembly Procedure ..................................... Engine Oil Pump - Install ....................................... Installation Procedure ........................................ Engine Oil Pump - Remove ................................... Removal Procedure ........................................... Engine Support (Front) - Remove and Install ........ Installation Procedure (Type 1) .......................... Installation Procedure (Type 2) .......................... Removal Procedure (Type 1) ............................. Removal Procedure (Type 2) ............................. Exhaust Manifold - Remove and Install ................. Installation Procedure ........................................ Removal Procedure ...........................................

107 Index Section

78 78 78 96 96 96 29 29 29 29 30 30 28 28 45 46 46 45 46 19 19 19

G Gear Group (Front) - Install ................................... Installation Procedure ........................................ Gear Group (Front) - Remove ............................... Removal Procedure ........................................... Gear Group (Rear) - Install.................................... Installation Procedure ........................................ Gear Group (Rear) - Remove................................ Removal Procedure ...........................................

56 56 55 55 48 48 46 46

H Housing (Front) - Install ......................................... Installation Procedure ........................................ Housing (Front) - Remove ..................................... Removal Procedure ........................................... Housing (Rear) - Install.......................................... Installation Procedure ........................................ Housing (Rear) - Remove...................................... Removal Procedure ...........................................

58 58 57 57 60 60 60 60

F

I

Fan - Remove and Install .................................... 101 Installation Procedure ...................................... 101 Removal Procedure ......................................... 101 Fan Drive - Remove and Install ........................... 102 Installation Procedure ...................................... 103 Removal Procedure ......................................... 102 Fan Guard - Remove and Install ......................... 100 Installation Procedure ...................................... 100 Removal Procedure ......................................... 100 Flywheel - Remove and Install .............................. 49 Installation Procedure ........................................ 49 Removal Procedure ........................................... 49 Flywheel Housing - Remove and Install ................ 51 Installation Procedure ........................................ 52 Removal Procedure ........................................... 51 Fuel Filter and Water Separator - Remove and Install .................................................................... 11 Installation Procedure ......................................... 11 Removal Procedure ............................................ 11 Fuel Filter Base - Install......................................... 10 Installation Procedure ........................................ 10 Fuel Filter Base - Remove..................................... 10 Removal Procedure ........................................... 10 Fuel Pressure Sensor - Remove and Install.......... 97 Installation Procedure ........................................ 97 Removal Procedure ........................................... 97 Fuel Priming Pump - Remove and Install ................ 9 Installation Procedure ........................................ 10 Removal Procedure ............................................. 9 Fuel Temperature Sensor - Remove and Install .... 97 Installation Procedure ........................................ 98 Removal Procedure ........................................... 97 Fuel Transfer Pump - Install .................................. 12 Installation Procedure ........................................ 12 Fuel Transfer Pump - Remove .............................. 12 Removal Procedure ........................................... 12

Important Safety Information ................................... 2 Inlet Air Temperature Sensor - Remove and Install ................................................................... 99 Installation Procedure ........................................ 99 Removal Procedure ........................................... 99 Inlet and Exhaust Valve Guides - Remove and Install ................................................................... 23 Installation Procedure ........................................ 24 Removal Procedure ........................................... 23 Inlet and Exhaust Valve Seat Inserts - Remove and Install ................................................................... 24 Installation Procedure ........................................ 25 Removal Procedure ........................................... 24 Inlet and Exhaust Valve Springs - Remove and Install ................................................................... 20 Installation Procedure ........................................ 21 Removal Procedure ........................................... 20 Inlet and Exhaust Valves - Remove and Install ..... 22 Installation Procedure ........................................ 23 Removal Procedure ........................................... 22 P Piston Cooling Jets - Remove and Install.............. Installation Procedure ........................................ Removal Procedure ........................................... Pistons and Connecting Rods - Assemble ............ Assembly Procedure.......................................... Pistons and Connecting Rods - Disassemble ....... Disassembly Procedure ..................................... Pistons and Connecting Rods - Install................... Installation Procedure ........................................ Pistons and Connecting Rods - Remove............... Removal Procedure ...........................................

80 80 80 82 82 82 82 83 83 81 81

R Radiator Core - Install............................................ Installation Procedure ........................................ Radiator Core - Remove........................................ Removal Procedure ........................................... Rocker Arm - Assemble......................................... Assembly Procedure.......................................... Rocker Arm - Disassemble.................................... Disassembly Procedure ..................................... Rocker Arm and Shaft - Install............................... Installation Procedure ........................................ Rocker Arm and Shaft - Remove........................... Removal Procedure ...........................................

44 44 42 42 64 64 64 64 65 65 63 63

Water Temperature Regulator Housing - Remove and Install ................................................................... 33 Installation Procedure ........................................ 34 Removal Procedure ........................................... 33

T Table of Contents..................................................... 3 Turbocharger - Assemble ...................................... 18 Assembly Procedure.......................................... 18 Turbocharger - Disassemble ................................. 17 Disassembly Procedure ..................................... 17 Turbocharger - Install ............................................ 18 Installation Procedure ........................................ 18 Turbocharger - Remove ........................................ 17 Removal Procedure ........................................... 17 Turbocharger Outlet Pressure Sensor - Remove and Install ................................................................... 98 Installation Procedure ........................................ 98 Removal Procedure ........................................... 98 V Valve Mechanism Cover - Remove and Install...... Installation Procedure ........................................ Removal Procedure ........................................... Valve Mechanism Cover Base - Remove and Install ................................................................... Installation Procedure ........................................ Removal Procedure ........................................... Vibration Damper and Pulley - Remove and Install ................................................................... Installation Procedure ........................................ Removal Procedure ...........................................

62 62 62 62 63 62 53 53 53

W Water Pump - Assemble........................................ Assembly Procedure.......................................... Water Pump - Disassemble ................................... Disassembly Procedure ..................................... Water Pump - Install .............................................. Installation Procedure ........................................ Water Pump - Remove .......................................... Removal Procedure ...........................................

©2008 Caterpillar All Rights Reserved

32 32 31 31 33 33 31 31

Cat, Caterpillar, their respective logos, “Caterpillar Yellow” and the Power edge trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.

Printed in U.S.A.

Caterpillar C27-C32.pdf

Recommend Documents