BRITISH STANDARD
BS 56 5649 49-2 -2:: 1978 EN 40-2 Incorporating Amendment No. 1
Specification for
Lighting columns — Part 2: Dimensions and tolerances
This European Standard EN 40-2 was given, as from 30 November 1978, the status of a British Standard and will replace the relevant requirements of BS 1308 1308,, BS 1840 and and BS 398 39899 (see nation national al forewo foreword) rd)
UDC 624.971:628.971:621.753.1
BS 564 5649-2: 9-2:197 1978 8
Cooperating organizations The European Committee for Standardization, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following Western European countries: Austria Belgium Denmark Finland France Germany Ireland Italy Netherlands Norway Portugal Spain Sweden Switzerland Unit Un ited ed Kin Kingd gdom om
This British Standard was published under the authority of the Execut Executive ive Board Board on 30 November 1978 © BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference RDB/28 Draft for comment 74/41655DC ISBN 0 580 10403 6
Österreichisches Normungsinstitut Institut Belge de Normalisation Dansk Standardiseringsraad Suomen Standardisoimisliitto, r.y. Association Française de Normalisation Deutsches Institut für Normung E.V. Institute for Industrial Research and Standards Ente Nazionale Italiano di Unificazione Nederlands No Normalisatie-instituut Norges St Standariseringsforbund Repartição de Normalização Instituto Nacional de Racionalización y Normalización Standardiseringskommissionen i Sverige Association Suisse de Normalisation Brit Br itis ish h Stan Standa dard rdss Inst Instit itut utio ion n
Amendments issued since publication
Amd. No.
Date of issue
Comments
3136
December 1979
Indicated by a sideline in the margin
BS 5649-2:1978
Contents Cooperating organizations National foreword Brief history Foreword 1 Scope and field of application 2 Post top columns, main dimensions 3 Columns with brackets, main dimensions 4 Door openings and cable entry slots 5 Column foundation, planting depth and base plate 6 Flange plate 7 Connection dimensions for lanterns 8 Tolerances Annex National particularities National appendix A National appendix B National appendix C Figure 1 Figure 2 Figure 3 — Position of door and cable entry slot Figure 4 — Dimensions of cutout Figure 5a Figure 5b Figure 6 Figure 7 Figure 8 Figure 9a Figure 9b Figure 10a Figure 10b Figure 11 Table 1 — Factor G
© BSI 09-1999
Page Inside front cover ii 2 2 3 4 5 6 7 8 9 10 11 11 11 11 12 4 5 6 6 7 7 8 8 8 9 9 9 9 10 11
i
BS 5649-2:1978
National foreword This BS/EN is being produced in the following Parts: — Part 1: Definitions and terms; — Part 2: Dimensions and tolerances; — Part 3: Materials1) ; — Part 4: Surface protection of metal columns1) ; — Part 5: Base compartment and cableways 1) ; — Part 6: Loads1) ; — Part 7: Verification of structural design by calculations1) ; — Part 8: Verification of structural design by testing 1) ; — Part 9: Special requirements for concrete columns 1). A further Part dealing with special requirements for plastics columns is in an early stage of preparation. BS 5649 will be issued in Parts as they are completed and approved, and until the whole document is published it will not be possible to supersede the present British Standards for lighting columns. As the Parts are issued recommendations will be given for their implementation together with a list of clauses in the existing standards which they will eventually supersede. It is hoped that a gradual change-over will be obtained which will terminate with the total withdrawal of the existing standards. The British Standards affected are: BS 1308:1970, Specification for concrete street lighting columns. BS 1840:1960, Specification for steel columns for street lighting. BS 3989:1966, Specification for aluminium street lighting columns. It is anticipated that the affected clauses in the existing standards will be withdrawn in accordance with the following timetable: BS 1840 and BS 3989, One year from the publication of this Part of this standard. BS 1308, Three years from the publication of Parts 6, 7, 8 and 9 of this standard. In the interim period it is permissible for dimensions and tolerances for lighting columns to be based on either the existing standards or on BS 5649-2. Purchasers specifying lighting schemes during the interim period should, where possible, permit either alternative. BS 5649-2 covers some or all of the requirements also covered in the following clauses of the existing British Standards: BS 1308 Scope 1.1 1.8.2 Straightness tolerances 1.8.3 Column height and bracket projection 1.10 Bracket projection 1.11 Lantern fixing 1.12.1 Door and door opening 1.18 Service connections
1) In course of preparation
ii
© BSI 09-1999
BS 5649-2:1978
BS 1840 1 Scope 5 Tolerances 6 Doors and door openings 8 Base-plates 10 Service slots 11 Relative positions of door openings, service slots and bracket arms 12 Recommended depth of columns in the ground 13 Lantern fixing BS 3989 1 Scope 6 Tolerances 8a) Doors and door openings 9 Base-plate 11 Service slot 12 Relative positions of bracket arm, door opening and service slot 13 Recommended depths of columns in the ground 14 Lantern fixing This standard includes columns of height greater than those that were envisaged in the scope of the existing BS 1308, BS 1840 and BS 3989. It is therefore inappropriate to use the design loading requirements in these British Standards for columns over 15 m in nominal height; for such columns the loading requirements should be agreed between the purchaser and the supplier, pending the issue of other Parts of this standard. Advice regarding the choice of planting depth is given in National appendix B. Convention. In this European Standard the comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, pages i to iv, the EN title page, pages 2 to 12 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. © BSI 09-1999
iii
iv
blank
EUROPEAN STANDARD
EN 40-2
NORME EUROPÉENNE Edition 1 June 1976
EUROPÄISCHE NORM UDC 624.971:628.971:621.753.1 Key words: Luminaire, lighting column, dimension, dimensional tolerance
English version
Lighting columns Part 2: Dimensions and tolerances
Candélabres Dimensions et tolérances
Lichtmaste Masse und zulässige Abweichungen
This European Standard was accepted by CEN on 1976-06-30. The CEN members are bound to adhere to the CEN Internal Regulations which specify under which conditions this European Standard has to be given, without any alteration, the status of a national standard. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. This European Standard is established by CEN in three official versions (English, French, German). A translation made by another member under its own responsibility, in its own language, and notified to CEN has the same status. CEN members are the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels
© Copyright reserved to all CEN members
EN 40-2
Brief history
This European Standard, drawn up by technical committee CEN/TC 50 “Lighting poles and spigots” (secretariat DIN), was submitted to the ballot of CEN members in February 1976 with a view to its adoption as a European Standard. It was adopted as such by CEN on 30 June 1976 on the strength of its acceptance by the following member countries: Austria, France, Germany, Ireland, Italy, Netherlands, Portugal, Switzerland, United Kingdom. Foreword
In producing this Part of this standard it was recognized that columns with nominal heights and/or bracket projections not specified in this standard will still be needed to replace columns in existing lighting schemes. However, all columns for new lighting schemes should be selected from the nominal heights and bracket projections specified in this document.
2
© BSI 09-1999
EN 40-2
1 Scope and field application This European Standard specifies the dimensions and tolerances for a chosen series of lighting columns adopted by CEN. It relates to post top columns for post top lanterns as well as columns with brackets for side entry lanterns. The dimensional requirements are specified except that the connection dimensions in clause 7 represent, for the time being, a recommended choice. It is proposed to make them mandatory after an interim period.
© BSI 09-1999
3
EN 40-2
2 Post top columns, main dimensions (in metres)
Figure 1
4
© BSI 09-1999
EN 40-2
3 Columns with brackets, main dimensions (in metres)
Figure 2
© BSI 09-1999
5
EN 40-2
4 Door openings and cable entry slots
(dimensions in millimetres)
Figure 4 — Dimensions of cutout
Figure 3 — Position of door4) and cable entry slot 1) Supplementary dimensions for concrete columns. 2) For metal columns only. 3) It is recommended that this dimension be approximately 600, but in no case shall it be less than 300; no maximum is specified. 4) It is recommended that the door opening is positioned parallel to the bracket on the side away from the direction of traffic. Figure 3 shows the position for right hand drive roads.
6
© BSI 09-1999
EN 40-2
5 Column foundation, planting depth and base plate
Figure 5a
(dimensions in millimetres)
Figure 5b
1)
The planting depth, e, shall be selected from the values given in the table taking into consideration the calculations made beforehand and the ground conditions.
© BSI 09-1999
7
EN 40-2
6 Flange plate
(dimensions in millimetres)
Figure 6
Figure 7 h
5 u 12 u
u
20
260 400 400 500
d1a
M18 M24 M27
sa
c
m
Figure 8
8 10
200 300 300 400
20 d2
22 30 33
a
min.
d1a
M18 M24 M27
la min.
400 500 700
a These dimensions shall be checked by calculation.
8
© BSI 09-1999
EN 40-2
7 Connection dimensions for lanterns
(in millimetres)2)
d1b
60 76 102
l1
70 130 250
Figure 9b a
Figure 9a
Post top lanterns
d2b
42 60
l2
100 100 250
Figure 10a
Figure 10b a
Side entry lanterns a This design does not apply to concrete columns. b Diameters of steel spigots should be as given in the International Standard of ISO 64:1974 “ Steel tubes, outside diameters”
for steel tubes of the nearest size.
2) See
clause 1.
© BSI 09-1999
9
EN 40-2
8.4 Projection (without spigot) ± 2
%
8.5 Fixing angle
The tolerance for the fixing angle of the lantern fixing axis, from the horizontal, shall be ± 2° when not under load; the deviation between the bracket axis and lantern fixing axis shall also not exceed ± 2°. 8.6 Door opening and cable entry slot
For the opening dimensions: + 5 mm – 0 mm 8.7 Column cross-section 8.7.1 Metal columns
Figure 11
Column circumference tolerance: ± 1 % 8.7.1.2 Deviation in shape 8.7.1.2.1 Circular cross-section: ± 3 % of the diameter calculated from the measured circumference (disregarding a welded seam bead) 8.7.1.2.2 Polygonal cross-section: ± 4 % of the nominal value over the flats of the polygon 8.7.1.1
8 Tolerances 8.1 Straightness
0,003 l; l = h + e %x u 0,003 %l; %l W 1 m See Figure 11. Measurement shall be carried out in unloaded state (column lying horizontally). x u
8.2 Total length of post top columns 8.2.1 Longitudinally welded columns
With planted section: ± 0,5 % ü ý or ± 25 mm With flange plate: ± 0,6 % þ (the greater value shall apply) 8.2.2 Seamless columns
With planted section: ± 0,5 % With flange plate: ± 0,6 % (the greater value shall apply)
ü ý þ
or ± 50 mm
8.7.2 Concrete columns
Column circumference tolerance: ± 1 % 8.7.2.2 Deviation in shape Cross-section dimensional tolerances: ± 5 %, min. value ± 10 mm 8.7.2.1
8.8 Connection dimensions for lanterns 8.8.1 Length of lantern connection for l1 or l2: ± 2 mm 8.8.2 Diameter of lantern connection (ungalvanized) for d1 or d2: see ISO 64:1974
8.3 Total length of columns with brackets
Column with planted section: Column with flange plate:
10
1% ± 1,2 % ±
© BSI 09-1999
EN 40-2
Alternatively, if the purchaser knows the soil conditions before ordering, the equation in B.3 can be used to calculate which planting depth would be National particularities suitable and a decision taken, depending upon In France it is admissible to use in addition to the availability and cost, to use that planting depth or to bracket projections fixed in clause 3 also the bracket use a shorter planting depth with a concrete or projections w = 1 m and w = 1,5 m. selected infill.
Annex
National appendix A The United Kingdom participation in the preparation of this European Standard came under the direction of the Road Engineering Standards Committee of BSI. The following organizations were involved in the work on this standard: Aluminium Federation Association of Public Lighting Engineers British Plastics Federation British Precast Concrete Federation Ltd. British Steel Industry Cement and Concrete Association County Surveyors’ Society Department of Transport Design Council Electricity Supply Industry in England and Wales Institution of Highway Engineers Institution of Mechanical Engineers Institution of Municipal Engineers Lighting Column Manufacturers’ Association Lighting Industry Federation Ltd. National appendix B Planting depth B.1 Selection
The planting depth of a column shall be selected from the table in clause 5 for the nominal height required. B.2 Suitability
To check the suitability of the selected planting depth for the ground conditions at the site it is suggested that the procedure given in B.3 should be adopted unless a more sophisticated foundation design is utilized. Where the selected planting depth is shown to be too short, this may be overcome by backfilling the excavation with mass concrete. The effective diameter of the column may then be assumed to be equal to the minimum diameter of the hole and the equation in B.3 can be used to calculate this diameter.
© BSI 09-1999
B.3 Calculation
a) Select planting depth. b) Calculate overturning moment due to full design forces on the column about a fulcrum located at 1/Æ2 of the planting depth. c) Multiply overturning moment by factor of safety 1.25. d) The moment in c) should not exceed the ground resistance moment (M g) obtained from 3 GD P M = ----------------g 10 where G is a factor dependent on the ground in which the column is planted (in kN/m2 per m) Values of G are given in Table 1. D is the minimum diameter (or minimum dimension across flats for multi-sided sections) of the section of the column in the ground (in m) P is the planting depth (in m) Table 1 — Factor G G
Soil type
630
Good: Compact, well graded sand and gravel, hard clay, well graded fine and coarse sand, decomposed granite rock and soil. Good material should be well drained and in locations where water will not stand. 390 Average: Compact fine sand, medium clay, compact, well drained sandy loam, loose coarse sand and gravel. Average soils should drain sufficiently well that water does not stand on the surface. 230 Poor: Soft clay, clay loam, poorly compacted sand, clays containing a large amount of silt and vegetable matter, and made ground. Poor soils will normally be wet and have poor drainage.
11
EN 40-2
B.4 Back filling
The approach in B.3 is based on the hole into which the column is placed being back filled with the excavated material or with material of better quality. All back filling material should be placed in 150 mm thick layers and should be well compacted. Where the hole is back filled with concrete, the concrete should extend from the base of the column to ground level. A duct, equal in size to the cable entry hole, should be formed through the concrete filling using a suitable preformed lining tube. Where bituminous surfacing is used round the column, the top level of the concrete may be lowered by the thickness of the surfacing.
b) Steel columns complying with BS 1840:1960. The loads from Table 3 of that standard increased by a factor of 2.0. c) Aluminium columns complying with BS 3989:1966. The loads from Table 4 of that standard. National appendix C References Clauses 7 and 8.8.2, make reference to ISO 64:1974 “Steel tubes, outside diameters ” for steel tubes of 42 mm, 60 mm, 76 mm and 102 mm outside diameter. That standard gives actual outside diameters of 42.4 mm, 60.3 mm, 76.1 mm and 101.6 mm without specifying tolerances.
B.5 Design loadings
Pending the issue of subsequent Parts of this standard, which will give details of the design loading for columns in particular zones of the country, the following loading should be adopted for calculating planting depths. a) Concrete columns complying with BS 1308:1970. The loads from Table 4 of that standard.
12
© BSI 09-1999
blank
BSI 389 Chiswick High Road London W4 4AL
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
BSI Ð British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions
British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards
Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards
BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means ± electronic, photocopying, recording or otherwise ± without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
