Металлопрокат и трубы по стандартам DIN , EN , ASTM
Поставляем металлопрокат по стандарту EN 00573-3 Для заказа металлопроката или получения консультации обращайтесь по следующим контактам: Россия:: Россия
+7 (495) 134-41-64
Беларусь:: +375 (29) Беларусь
388-04-11
Казахстан:: +7 (7172) 72-76-96 Казахстан
www.emk.bz
[email protected] Стандарт предоставлен исключительно для ознакомления
BS EN 573-3:2013
BSI Standards Publication
Aluminium and aluminium alloys — Chemical composition and form of wrought products products Part 3: Chemical composition and form of products
BS EN 573-3:2013
BRITISH STANDARD
National foreword This British Standard is the UK implementation of EN 573-3:201 3. It supersedes BS EN 573-3:2009 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. © The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 82399 2 ICS 77.120.10; 77.150.10
Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2013.
Amendmentss issued since publication Amendment Date
Text affected
BS EN 573-3:2013
EUROPEAN STANDARD
EN 573-3
NORME EUROPÉENNE EUROPÄISCHE NORM
October 2013
ICS 77.120.10; 77.150.10
Supersedes EN 573-3:2009
English Version
Aluminium and aluminium alloys - Chemical composition composition and form of wrought products - Part 3: Chemical composition and form of products Aluminium et alliages d'aluminium - Composition chimique chimique et forme des produits corroyés - Partie 3: Composition chimique et forme des produits
Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von Halbzeug - Teil 3: Chemische Zusammensetzung und Erzeugnisformen
This European Standard was approved by CEN on 15 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenu Avenue e Marnix 17, 17, B-1000 Brussels Brussels
© 2013 CEN
All rights of exploitation exploitation in any any form and by any means means reserved reserved worldwide for CEN national Members.
Ref. No. EN 573-3:2013: E
BS EN 573-3:2013
EN 573-3:2013 (E)
Contents
Page
For ewo rd ........................................................................................................ ..............................................................................................................................................................3 ......................................................3 1
Sco pe ........................................................ ..................................................................................................................... ..............................................................................................4 .................................4
2
Nor mat iv e ref eren ces ..................................................... ................................................................................................................. .......................................................................4 ...........4
3
Chemi cal co mp os it io n li mi ts ........... ................. ........... ........... ........... ........... ........... ........... ........... ........... ........... ........... ............ ........... ........... ........... ........... ........... ........... .......4 .4
4
Wri ti ng ru les ......................................................... ..................................................................................................................... ..................................................................................4 ......................4
5
Al lo y des ig nat io ns ......................................................... ..................................................................................................................... ........................................................................5 ............5
6
Sequ enc e of elem ent s ............................................................. .......................................................................................................................... ..............................................................5 .5
7
Roun di ng ru les fo r det erm in atio n of comp co mp li anc e ........... ................. ........... ........... ........... ........... ........... ........... ........... ........... ............ ........... ........... ......5 5
An nex A (normative) For m of prod pr od uc ts .......................................................... ......................................................................................................... ............................................... 20 A.1 Gener al ...................................................... ................................................................................................................... ........................................................................................... .............................. 20 A.2 Eur op ean St and ard s ...................................................... .................................................................................................................. ..................................................................... ......... 20 An nex B (normative) Guidelines Guidelines for the introduction of new wrought aluminium and wrought alum in iu m all oy s in CEN/TC 132 st andar ds ......... ............... ........... ........... ........... ........... ........... ........... ........... ........... ............ ........... ........... ........... ......... .... 34 B.1 Gener al pr in ci pl es............................................................................................................ es............................................................................................................................... ................... 34 B.2 Rules fo r in tr od uc ti on of new allo ys ........... ................. ........... ........... ........... ........... ........... ........... ............ ........... ........... ........... ........... ........... ........... ........... ........ ... 34 B.3 Pro ced ur e fo r in tr od uc ti on of new allo ys ........... ................ ........... ............ ........... ........... ........... ........... ........... ........... ........... ........... ............ ........... .......... ..... 34 B.4 Ad den du m fo r new allo ys fo r fu tu re in tr od uc ti on ........... ................. ........... ........... ........... ........... ........... ........... ............ ........... ........... ........... ........ ... 34 Bibliography ..................................................................................................................................................... 35
2
BS EN 573-3:2013
EN 573-3:2013 (E)
Foreword This document (EN 573-3:2013) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2014, and conflicting national standards shall be withdrawn at the latest by April 2014. Attention is drawn to t o the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 573-3:2009. 573-3:2009. CEN/TC 132 affirms its policy that if a patentee refuses to grant licenses on standardized products under reasonable and not discriminatory conditions, this product will be removed from the corresponding document. Within its programme of work, Technical Committee CEN/TC 132 entrusted entrust ed CEN/TC 132/WG 7 "Sheets, strips and plates" to revise EN 573-3:2009. 573-3:2009. CEN/TC 132 has decided to revise this Europe an Standard as follows:
addition of the alloy EN AW-4115 AW-4115 in Table 4 and Table A.4; addition of the alloy EN AW-5449A AW-5449A in Table 5 and Table A.5; addition of the alloys EN AW-6026 and EN AW-6064A in Table 6 and Table A.6; error in the chemical symbol of EN AW-6023 in Table A.6. correction of a typing error EN 573 comprises the following parts under the general title Aluminium "Aluminium and aluminium alloys — Chemical composition and form of wrought products ":
Part 1: Numerical designation system Part 2: Chemical symbol based designation system Part 3: Chemical composition and form of products Part 5: Codification of standardized wrought products According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3
BS EN 573-3:2013
EN 573-3:2013 (E)
1
Scope
This European Standard specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products. The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminum Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys. Guidelines for the introduction of new wrought aluminium and wrought aluminium alloys in standards are presented in Annex B.
2
Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 573-2, 573-2, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 2: Chemical symbol based designation system
3
Chemical Chemical composi tion limit s
The chemical composition of aluminium and aluminium alloys is specified in percentage by mass in Table 1 to Table 8. Limits of impurities are expressed as a maximum; limits of alloying elements shown as a range aluminium is specified as a minimum for unalloyed aluminium, and as a remainder for aluminium alloys. The chemical composition of internationally registered wrought aluminium and wrought aluminium alloys not listed in this document can be found in Teal sheet [1]. Analysis shall be made for elements which are specified, for example Pb, Sn, Bi, Sb, Zr.
4
Writing rules
4.1 Standard limits for alloying elements and impurities are expressed in percentage by mass to the following decimal places:
less than 0,001 %
0,000 X;
0,001 % but less than 0,01 %
0,00X;
0,01 % but less than 0,10 %: unalloyed aluminium made by a refining process
0,0XX;
others
0,0X;
0,10 % to 0,55 %
0,XX;
over 0,55 %
0,X; X,X; XX,X.
Exception: combined Si + Fe limits for 1xxx designations shall be expressed as 0,XX or 1,XX.
4
BS EN 573-3:2013
EN 573-3:2013 (E)
The aluminium aluminium content for unalloyed aluminium made by a refining process is is the difference 4.2 between 100,00 % and the sum of all other metallic elements present in amounts of 0,001 0 % or more each, expressed to the third decimal place before determining the sum, which is rounded to the second decimal place before subtracting. For unalloyed aluminium not made by a refining process, the aluminium content is the difference between 100,00 % and the sum of all other metallic elements present in amounts of 0,010 % or more each expressed to the second decimal place before determining the sum.
5
Alloy designations
The numerical designation systems used in Teal sheets and European Standards for wrought aluminium alloys are identical. As specified in EN 573-1 the 573-1 the prefix EN AW- is added. The alternative chemical symbol based alloy designation s ystem shall be based onEN on EN 573-2. 573-2. Both the numerical and the chemical symbol based designations are indicated in Table 1 to Table 8. The International numerical system is the preferred one. The chemical symbol based designations are indicated for reference only.
6
Sequence Sequence of elements elements
Standard limits for alloying elements and impurities are expressed in the following sequence: silicon, iron, copper, manganese, magnesium, chromium, nickel, zinc, titanium, gallium, vanadium, remarks, other elements each, other elements total, aluminium. Limits of additional specified elements are inserted in alphabetical order of their chemical symbols under “Remarks”.
7
Rounding rules for determination determination of compliance
In recording chemical analysis test results, the number representing the result for any element specified in this standard shall be expressed to the same number of decimal places as the corresponding number in this standard. For unalloyed aluminium, the aluminium content is derived as described in 4.2. The following rounding rules shall be used for determination of compliance with this European Standard: a)
when the figure immediately after the last last figure to be retained is less than 5, the last figure to be retained remains unchanged;
b)
when the figure immediately after the last figure to be retained is greater than 5, or equal to 5 and followed by at least one figure other than zero, the last figure to be retained is increased by one;
c)
when the figure immediately after the last figure to be retained retained is equal to 5 and followed by zeros zeros only, the last figure to be retained remains unchanged if even and is increased by one if odd.
5
EN 573-3:2013 (E)
Table 1 — Aluminium — 1 000 series Others a
Allo y desig natio n Numerical
Chemical symbols
Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Remarks
Alumi nium
Each
Total b
min.
EN AW-1050A
EN AW-Al 99,5
0,25
0,40
0,05
0,05
0,05
-
-
0,07
0,05
-
-
-
0,03
-
99,50 c
EN AW-1060
EN AW-Al 99,6
0,25
0,35
0,05
0,03
0,03
-
-
0,05
0,03
-
0,05
-
0,03
-
99,60 c
EN AW-1070A
EN AW-Al 99,7
0,20
0,25
0,03
0,03
0,03
-
-
0,07
0,03
-
-
-
0,03
-
99,70 c
0,02
-
99,80 c
EN AW-1080A
EN AW-Al 99,8(A)
0,15
0,15
0,03
0,02
0,02
-
-
0,06
0,02
0,03
-
e
EN AW-1085
EN AW-Al 99,85
0,10
0,12
0,03
0,02
0,02
-
-
0,03
0,02
0,03
0,05
-
0,01
-
99,85 c
EN AW-1090
EN AW-Al 99,90
0,07
0,07
0,02
0,01
0,01
-
-
0,03
0,01
0,03
0,05
-
0,01
-
99,90 c
EN AW-1098
EN AW-Al 99,98
0,010
0,006
EN AW-1100
EN AW-Al 99,0Cu
EN AW-1110
EN AW-Al 99,1
0,95 Si + Fe 0,30
0,8
0,003
-
-
-
-
0,015
0,003
-
-
-
0,003
-
99,98 d
0,05-0,20
0,05
-
-
-
0,10
-
-
-
e
0,05
0,15
99,00 c
0,04
0,01
0,25
0,01
–
–
–
–
–
0,02B; 0,03V + Ti
0,03
0,15
99,10
c d
EN AW-1198
EN AW-Al 99,98(A)
0,010
0,006
0,006
0,006
-
-
-
0,010
0,006
0,006
-
-
0,003
-
99,98
EN AW-1199
EN AW-Al 99,99
0,006
0,006
0,006
0,002
0,006
-
-
0,006
0,002
0,005
0,005
-
0,002
-
99,99 d
EN AW-1200
EN AW-Al 99,0
1,00 Si + Fe
0,05
0,05
-
-
-
0,10
0,05
-
-
e
0,05
0,15
99,00 c
EN AW-1200A
EN AW-Al 99,0(A)
1,00 Si + Fe
0,10
0,30
0,30
0,10
-
0,10
-
-
-
-
0,05
0,15
99,00 c
EN AW-1235
EN AW-Al 99,35
0,65 Si + Fe
0,05
0,05
0,05
-
-
0,10
0,06
-
0,05
-
0,03
-
99,35 c
EN AW-1350
EN AW-Al 99,5
0,10
0,40
0,05
0,01
-
0,01
-
0,05
-
0,03
-
0,05 B; 0,02 V + Ti
0,03
0,10
99,50 c
EN AW-1350A
EN AW-Al 99,5(A)
0,25
0,40
0,02
-
0,05
-
-
0,05
-
-
-
0,03 Cr + Mn + Ti + V
0,03
-
99,50 c
6
EN 573-3:2013 (E)
Table 1 — Aluminium — 1 000 series (continued) Others a
Allo y desig natio n Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Numerical
Chemical symbols
EN AW-1370
EN AW-Al 99,7
0,10
0,25
0,02
0,01
0,02
0,01
-
0,04
-
0,03
-
EN AW-1450
EN AW-Al 99,5Ti
0,25
0,40
0,05
0,05
0,05
-
-
0,07
0,10-0,20 0,10-0,20
-
-
Remarks
Alumi nium
Each
Total b
min.
0,02 B; 0,02 V + Ti
0,02
0,10
99,70 c
e
0,03
-
99,50 c
a
"Others" includes listed elements elements for which no specific specific limit is shown as well as unlisted unlisted metallic elements. The producer producer may analyse samples samples for trace elements not not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of those "Others" "Others" metallic elements elements 0,010 % or more each, expressed to the second second decimal place before determining the sum.
c
The aluminium content for unalloyed aluminium not made made by a refining process is the difference between between 100,00 % and the sum of all other metallic metallic elements present in amounts of 0,010 % or more more each, expressed to the second decimal place before determining the sum.
d
The aluminium content for unalloyed unalloyed aluminium made by a refining process is the difference difference between 100,00 % and the sum of all other metallic metallic elements present in amounts of 0,0010 % or more each, expressed to the third decimal decimal before determining the sum, which is rounded to the second decimal place before subtracting.
e
0,000 3 max. Be for welding electrode, welding rod and filler wire only.
7
EN 573-3:2013 (E)
Table 1 — Aluminium — 1 000 series (continued) Others a
Allo y desig natio n Numerical
Si
Chemical symbols
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Remarks
Alumi nium
Each
Total b
min.
EN AW-1370
EN AW-Al 99,7
0,10
0,25
0,02
0,01
0,02
0,01
-
0,04
-
0,03
-
0,02 B; 0,02 V + Ti
0,02
0,10
99,70 c
EN AW-1450
EN AW-Al 99,5Ti
0,25
0,40
0,05
0,05
0,05
-
-
0,07
0,10-0,20 0,10-0,20
-
-
e
0,03
-
99,50 c
a
"Others" includes listed elements elements for which no specific specific limit is shown as well as unlisted unlisted metallic elements. The producer producer may analyse samples samples for trace elements not not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of those "Others" "Others" metallic elements elements 0,010 % or more each, expressed to the second second decimal place before determining the sum.
c
The aluminium content for unalloyed aluminium not made made by a refining process is the difference between between 100,00 % and the sum of all other metallic metallic elements present in amounts of 0,010 % or more more each, expressed to the second decimal place before determining the sum.
d
The aluminium content for unalloyed unalloyed aluminium made by a refining process is the difference difference between 100,00 % and the sum of all other metallic metallic elements present in amounts of 0,0010 % or more each, expressed to the third decimal decimal before determining the sum, which is rounded to the second decimal place before subtracting.
e
0,000 3 max. Be for welding electrode, welding rod and filler wire only.
7
EN 573-3:2013 (E)
Table 2 — Aluminium alloys — 2 000 series — Al Cu Others a
Allo y desi gnati on Si Numerical
8
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Alum iniu m
Remarks
Chemical symbols c
Each
Total b
min.
EN AW-2001
EN AW-Al Cu5,5MgMn
0,20
0,20
5,2-6,0
0,15-0,50
0,20-0,45
0,10
0,05
0,10
0,20
-
-
0,05
0,15
Remainder
EN AW-2007
EN AW-Al Cu4PbMgMn
0,8
0,8
3,3-4,6
0,50-1,0
0,40-1,8
0,10
0,20
0,8
0,20
-
-
d
0,10
0,30
Remainder
EN AW-2011
EN AW-Al Cu6BiPb
0,40
0,7
5,0-6,0
-
-
-
-
0,30
-
-
-
e
0,05
0,15
Remainder
EN AW-2011A
EN AW-Al Cu6BiPb(A)
0,40
0,50
4,5-6,0
-
-
-
-
0,30
-
-
-
e
0,05
0,15
Remainder
0,05 Zr
EN AW-2014
EN AW-Al Cu4SiMg
0,50-1,2
0,7
3,9-5,0
0,40-1,2
0,20-0,8
0,10
-
0,25
0,15
-
-
f
0,05
0,15
Remainder
EN AW-2014A
EN AW-Al Cu4SiMg(A)
0,50-0,9
0,50
3,9-5,0
0,40-1,2
0,20-0,8
0,10
0,10 0,10
0,25
0,15
-
-
0,20 Zr+Ti
0,05
0,15
Remainder
EN AW-2017A
EN AW-Al Cu4MgSi(A)
0,20-0,8
0,7
3,5-4,5
0,40-1,0
0,40-1,0
0,10
-
0,25
-
-
-
0,25 Zr+Ti
0,05
0,15
Remainder
EN AW-2024
EN AW-Al Cu4Mg1
0,50
0,50
3,8-4,9
0,30-0,9
1,2-1,8
0,10
-
0,25
0,15
-
-
f
0,05
0,15
Remainder
EN AW-2030
EN AW-Al Cu4PbMg
0,8
0,7
3,3-4,5
0,20-1,0
0,50-1,3
0,10
-
0,50
0,20
-
-
0,20 Bi ; 0,8-1,5 Pb
0,10
0,30
Remainder
EN AW-2031
EN AW-Al Cu2,5NiMg
0,50-1,3
0,6-1,2
1,8-2,8
0,50 0,50
0,6-1,2
-
0,6-1,4
0,20
0,20
-
-
-
0,05 g
0,15
Remainder
EN AW-2091
EN AW-Al Cu2Li2Mg1,5
0,20
0,30
1,8-2,5
0,10
1,1-1,9
0,10
-
0,25
0,10
-
-
0,04-0,16 Zr
0,05
0,15
Remainder
EN AW-2117
EN AW-Al Cu2,5Mg
0,8
0,7
2,2-3,0
0,20
0,20-0,50
0,10
-
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-2124
EN AW-Al Cu4Mg1(A)
0,20
0,30
3,8-4,9
0,30-0,9
1,2-1,8
0,10 0,10
-
0,25
0,15
-
-
f
0,05
0,15
Remainder
0,05
0,15
Remainder
0,05
0,15
Remainder
EN AW-2214
EN AW-Al Cu4SiMg(B)
0,50-1,2 0,50-1,2
0,30
3,9-5,0
0,40-1,2
0,20-0,8
0,10
-
0,25
0,15
-
-
f
EN AW-2219
EN AW-Al Cu6Mn
0,20
0,30
5,8-6,8
0,20-0,40
0,02
-
-
0,10
0,02-0,10
-
0,05-0,15
0,10-0,25 Zr
EN 573-3:2013 (E)
Table 2 — Aluminium alloys — 2 000 series — Al Cu Others a
Allo y desi gnati on Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Remarks c
Chemical symbols
Alum iniu m
Each
Total b
min.
EN AW-2001
EN AW-Al Cu5,5MgMn
0,20
0,20
5,2-6,0
0,15-0,50
0,20-0,45
0,10
0,05
0,10
0,20
-
-
0,05
0,15
Remainder
EN AW-2007
EN AW-Al Cu4PbMgMn
0,8
0,8
3,3-4,6
0,50-1,0
0,40-1,8
0,10
0,20
0,8
0,20
-
-
d
0,10
0,30
Remainder
EN AW-2011
EN AW-Al Cu6BiPb
0,40
0,7
5,0-6,0
-
-
-
-
0,30
-
-
-
e
0,05
0,15
Remainder
0,05
0,15
Remainder
0,05
0,15
Remainder
0,05 Zr
EN AW-2011A
EN AW-Al Cu6BiPb(A)
0,40
0,50
4,5-6,0
-
-
-
-
0,30
-
-
-
e
EN AW-2014
EN AW-Al Cu4SiMg
0,50-1,2
0,7
3,9-5,0
0,40-1,2
0,20-0,8
0,10
-
0,25
0,15
-
-
f
EN AW-2014A
EN AW-Al Cu4SiMg(A)
0,50-0,9
0,50
3,9-5,0
0,40-1,2
0,20-0,8
0,10
0,10 0,10
0,25
0,15
-
-
0,20 Zr+Ti
0,05
0,15
Remainder
EN AW-2017A
EN AW-Al Cu4MgSi(A)
0,20-0,8
0,7
3,5-4,5
0,40-1,0
0,40-1,0
0,10
-
0,25
-
-
-
0,25 Zr+Ti
0,05
0,15
Remainder
EN AW-2024
EN AW-Al Cu4Mg1
0,50
0,50
3,8-4,9
0,30-0,9
1,2-1,8
0,10
-
0,25
0,15
-
-
f
0,05
0,15
Remainder
0,10
0,30
Remainder
0,05
EN AW-2030
EN AW-Al Cu4PbMg
0,8
0,7
3,3-4,5
0,20-1,0
0,50-1,3
0,10
-
0,50
0,20
-
-
0,20 Bi ; 0,8-1,5 Pb
EN AW-2031
EN AW-Al Cu2,5NiMg
0,50-1,3
0,6-1,2
1,8-2,8
0,50 0,50
0,6-1,2
-
0,6-1,4
0,20
0,20
-
-
g
0,15
Remainder
EN AW-2091
EN AW-Al Cu2Li2Mg1,5
0,20
0,30
1,8-2,5
0,10
1,1-1,9
0,10
-
0,25
0,10
-
-
0,04-0,16 Zr
0,05
0,15
Remainder
EN AW-2117
EN AW-Al Cu2,5Mg
0,8
0,7
2,2-3,0
0,20
0,20-0,50
0,10
-
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-2124
EN AW-Al Cu4Mg1(A)
0,20
0,30
3,8-4,9
0,30-0,9
1,2-1,8
0,10 0,10
-
0,25
0,15
-
-
f
0,05
0,15
Remainder
EN AW-2214
EN AW-Al Cu4SiMg(B)
0,50-1,2 0,50-1,2
0,30
3,9-5,0
0,40-1,2
0,20-0,8
0,10
-
0,25
0,15
-
-
f
0,05
0,15
Remainder
EN AW-2219
EN AW-Al Cu6Mn
0,20
0,30
5,8-6,8
0,20-0,40
0,02
-
-
0,10
0,02-0,10
-
0,05-0,15
0,10-0,25 Zr
0,05
0,15
Remainder
8
EN 573-3:2013 (E)
Table 2 — Aluminium alloys — 2 000 series series — Al Cu (continued) Others a
Allo y desi gnati on Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Chemical symbols
Total b
min.
0,05
0,15
Remainder
0,05
0,15
Remainder
Each
EN AW-2319
EN AW-Al Cu6Mn(A)
0,20
0,30
5,8-6,8
0,20-0,40
0,02
-
-
0,10
0,10-0,20
-
0,05-0,15 0,05-0,15
EN AW-2618A
EN AW-Al Cu2Mg1,5Ni
0,15-0,25
0,9-1,4
1,8-2,7
0,25
1,2-1,8
-
0,8-1,4
0,15
0,20
-
-
Alum iniu m
Remarks
0,10-0,25 Zr 0,25 Zr+Ti
h
a
"Others" includes listed elements for which no specific specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace trace elements not specified in the the registration or specification. specification. However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of those "Others" metallic elements 0,010 % or more each, expressed expressed to the the second decimal decimal place before determining the sum.
c
0,003 max. Pb.
d
0,20 Bi; 0,8-1,5 Pb; 0,20 Sn.
e
0,20-0,6 Bi; 0,20-0,6 Pb.
f
Zr + Ti limit of 0,20 maximum may be used for extruded and forged products if mutually agreed agreed by supplier or or manufacturer and purchaser. purchaser.
g
1,7-2,3 Li.
h
0,000 3 max. Be for welding electrode, electrode, welding rod and filler wire only.
9
EN 573-3:2013 (E)
Table 2 — Aluminium alloys — 2 000 series series — Al Cu (continued) Others a
Allo y desi gnati on Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Chemical symbols
Total b
min.
0,05
0,15
Remainder
0,05
0,15
Remainder
Each
EN AW-2319
EN AW-Al Cu6Mn(A)
0,20
0,30
5,8-6,8
0,20-0,40
0,02
-
-
0,10
0,10-0,20
-
0,05-0,15 0,05-0,15
EN AW-2618A
EN AW-Al Cu2Mg1,5Ni
0,15-0,25
0,9-1,4
1,8-2,7
0,25
1,2-1,8
-
0,8-1,4
0,15
0,20
-
-
Alum iniu m
Remarks
0,10-0,25 Zr 0,25 Zr+Ti
h
a
"Others" includes listed elements for which no specific specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace trace elements not specified in the the registration or specification. specification. However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of those "Others" metallic elements 0,010 % or more each, expressed expressed to the the second decimal decimal place before determining the sum.
c
0,003 max. Pb.
d
0,20 Bi; 0,8-1,5 Pb; 0,20 Sn.
e
0,20-0,6 Bi; 0,20-0,6 Pb.
f
Zr + Ti limit of 0,20 maximum may be used for extruded and forged products if mutually agreed agreed by supplier or or manufacturer and purchaser. purchaser.
g
1,7-2,3 Li.
h
0,000 3 max. Be for welding electrode, electrode, welding rod and filler wire only.
9
EN 573-3:2013 (E)
Table 3 — Aluminium alloys — 3 000 000 series — Al Mn Others a
Allo y desi gnati on Si Numerical
Chemical Symbols
EN AW-3002
EN AW-Al Mn0,2Mg0,1
0,08
Fe
Cu
0,10
0,15
Mn
0,05-0,25
Mg
Cr
Ni
0,05-0,20
-
-
Zn
Ti
Ga
V
Alum iniu m
Remarks Each
Total b
0,05
0,03
-
0,05
-
0,03
0,10
min. Remainder
EN AW-3003
EN AW-Al Mn1Cu
0,6
0,7
0,05-0,20
1,0-1,5
-
-
-
0,10
-
-
-
-
0,05
0,15
Remainder Remainder
EN AW-3004
EN AW-Al Mn1Mg1
0,30
0,7
0,25
1,0-1,5
0,8-1,3
-
-
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-3005
EN AW-Al Mn1Mg0,5
0,6
0,7
0,30
1,0-1,5
0,20-0,6
0,10
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3005A
EN AW-Al Mn1Mg0,5(A)
0,7
0,8
0,30
1,0-1,5
0,20-0,6
0,10
-
0,40
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3017
EN AW-Al Mn1Cu0,3
0,25
0,25-0,45
0,25-0,40
0,8-1,2
0,10
0,15
-
0,10
0,05
-
-
-
0,05
0,15
Remainder
EN AW-3102
EN AW-Al Mn0,2
0,40
0,7
0,10
0,05-0,40
-
-
-
0,30
0,10
-
-
-
0,05
0,15
Remainder Remainder
EN AW-3103
EN AW-Al Mn1
0,50
0,7
0,10
0,9-1,5
0,30
0,10
-
0,20
-
-
-
0,10 Zr+Ti c
0,05
0,15
Remainder Remainder
EN AW-3103A
EN AW-Al Mn1(A)
0,50
0,7
0,10
0,7-1,4
0,30
0,10
-
0,20
0,10
-
-
0,10 Zr+Ti
0,05
0,15
Remainder
EN AW-3104
EN AW-Al Mn1Mg1Cu
0,6
0,8
0,05-0,25
0,8-1,4
0,8-1,3
-
-
0,25
0,10
0,05
0,05
-
0,05
0,15
Remainder
EN AW-3105
EN AW-Al Mn0,5Mg0,5
0,6 0,6
0,7
0,30
0,30-0,8
0,20-0,8
0,20
-
0,40
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3105A
EN AW-Al Mn0,5Mg0,5(A)
0,6
0,7
0,30
0,30-0,8
0,20-0,8
0,20
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3105B
EN AW-Al Mn0,6Mg0,5
0,7
0,9
0,30
0,30-0,9
0,20-0,8
0,20 0,20
-
0,50
0,10
-
-
0,10 Pb
0,05
0,15
Remainder
EN AW-3207
EN AW-Al Mn0,6
0,30
0,45
0,10
0,40-0,8
0,10
-
-
0,10
-
-
-
-
0,05
0,10
Remainder Remainder
EN AW-3207A
EN AW-Al Mn0,6(A)
0,35
0,6
0,25
0,30-0,8
0,40
0,20
-
0,25
-
-
-
-
0,05
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,000 3 max. Be for welding electrode, electrode, welding rod and filler wire only.
10
EN 573-3:2013 (E)
Table 3 — Aluminium alloys — 3 000 000 series — Al Mn Others a
Allo y desi gnati on Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Alum iniu m
Remarks
Numerical
Chemical Symbols
EN AW-3002
EN AW-Al Mn0,2Mg0,1
0,08
0,10
0,15
0,05-0,25
0,05-0,20
-
-
0,05
0,03
-
0,05
-
EN AW-3003
EN AW-Al Mn1Cu
0,6
0,7
0,05-0,20
1,0-1,5
-
-
-
0,10
-
-
-
-
EN AW-3004
EN AW-Al Mn1Mg1
0,30
0,7
0,25
1,0-1,5
0,8-1,3
-
-
0,25
-
-
-
-
Total b
min.
0,03
0,10
Remainder
0,05
0,15
Remainder Remainder
0,05
0,15
Remainder
Each
EN AW-3005
EN AW-Al Mn1Mg0,5
0,6
0,7
0,30
1,0-1,5
0,20-0,6
0,10
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3005A
EN AW-Al Mn1Mg0,5(A)
0,7
0,8
0,30
1,0-1,5
0,20-0,6
0,10
-
0,40
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3017
EN AW-Al Mn1Cu0,3
0,25
0,25-0,45
0,25-0,40
0,8-1,2
0,10
0,15
-
0,10
0,05
-
-
-
0,05
0,15
Remainder
EN AW-3102
EN AW-Al Mn0,2
0,40
0,7
0,10
0,05-0,40
-
-
-
0,30
0,10
-
-
-
0,05
0,15
Remainder Remainder
c
EN AW-3103
EN AW-Al Mn1
0,50
0,7
0,10
0,9-1,5
0,30
0,10
-
0,20
-
-
-
EN AW-3103A
EN AW-Al Mn1(A)
0,50
0,7
0,10
0,7-1,4
0,30
0,10
-
0,20
0,10
-
-
EN AW-3104
EN AW-Al Mn1Mg1Cu
0,6
0,8
0,05-0,25
0,8-1,4
0,8-1,3
-
-
0,25
0,10
0,05
0,05
-
0,05
0,15
Remainder
EN AW-3105
EN AW-Al Mn0,5Mg0,5
0,6 0,6
0,7
0,30
0,30-0,8
0,20-0,8
0,20
-
0,40
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3105A
EN AW-Al Mn0,5Mg0,5(A)
0,6
0,7
0,30
0,30-0,8
0,20-0,8
0,20
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-3105B
EN AW-Al Mn0,6Mg0,5
0,7
0,9
0,30
0,30-0,9
0,20-0,8
0,20 0,20
-
0,50
0,10
-
-
0,10 Pb
0,05
0,15
Remainder
EN AW-3207
EN AW-Al Mn0,6
0,30
0,45
0,10
0,40-0,8
0,10
-
-
0,10
-
-
-
-
0,05
0,10
Remainder Remainder
EN AW-3207A
EN AW-Al Mn0,6(A)
0,35
0,6
0,25
0,30-0,8
0,40
0,20
-
0,25
-
-
-
-
0,05
0,15
Remainder
0,10 Zr+Ti
0,10 Zr+Ti
0,05
0,15
Remainder Remainder
0,05
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,000 3 max. Be for welding electrode, electrode, welding rod and filler wire only.
10
EN 573-3:2013 (E)
Table 4 — Aluminium alloys — 4 000 series — Al Si Othersa
Allo y desig natio n Si Numerical
Chemical symbols
EN AW-4004
EN AW-Al Si10Mg1,5
9,0-10,5
Fe
0,8
Cu
0,25
Mn
0,10
Mg
1,0-2,0
Cr
-
Ni
-
Zn
0,20
Ti
-
Ga
-
V
-
Alum iniu m
Remarks
-
Each
Total b
min.
0,05
0,15
Remainder
EN AW-4006
EN AW-Al Si1Fe
0,8-1,2
0,50-0,8
0,10
0,05
0,01
0,20
-
0,05
-
-
-
-
0,05
0,15
Remainder
EN AW-4007
EN AW-Al Si1,5Mn
1,0-1,7
0,40-1,0
0,20
0,8-1,5
0,20
0,05-0,25
0,15-0,7
0,10
0,10
-
-
0,05 Co
0,05
0,15
Remainder
EN AW-4015
EN AW-Al Si2Mn
1,4-2,2
0,7
0,20
0,6-1,2
0,10-0,50
-
-
0,20
-
-
-
-
0,05
0,15
Remainder
EN AW-4016
EN AW-Al Si2MnZn
1,4-2,2
0,7
0,20
0,6-1,2
0,10
-
-
0,50-1,3
-
-
-
-
0,05
0,15
Remainder
EN AW-4017
EN AW-Al SiMnMgCu
0,6-1,6
0,7
0,10-0,50
0,6-1,2
0,10-0,50
-
-
0,20
-
-
-
-
0,05
0,15
Remainder
EN AW-4018
EN AW-Al Si7Mg
6,5-7,5
0,20
0,05
0,10
0,50-0,8
-
-
0,10
0,20
-
-
c
0,05
0,15
Remainder
EN AW-4032
EN AW-Al Si12,5MgCuNi
11,0-13,5
1,0
0,50-1,3
-
0,8-1,3
0,10
0,50-1,3
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-4043A
EN AW-Al Si5(A)
4,5-6,0
0,6
0,30
0,15
0,20
-
-
0,10
0,15
-
-
c
0,05
0,15
Remainder
EN AW-4045
EN AW-Al Si10
9,0-11,0
0,8
0,30
0,05
0,05
-
-
0,10
0,20
-
-
-
0,05
0,15
Remainder
EN AW-4046
EN AW-Al Si10Mg
9,0-11,0
0,50
0,03
0,40
0,20-0,50
-
-
0,10
0,15
-
-
c
0,05
0,15
Remainder
EN AW-4047A
EN AW-Al Si12(A)
11,0-13,0
0,6
0,30
0,15
0,10
-
-
0,20
0,15
-
-
c
0,05
0,15
Remainder
EN AW-4104
EN AW-Al Si10MgBi
9,0-10,5
0,8
0,25
0,10
1,0-2,0
-
-
0,20
-
-
-
0,02-0,20 Bi
0,05
0,15
Remainder
EN AW-4115
EN AW-Al Si2MnMgCu
1,8-2,2
0,7
0,10-0,50
0,6-1,2
0,10-0,50
-
-
0,20
-
-
-
-
0,05
0,15
Remainder
EN AW-4343
EN AW-AI Si7,5
6,8-8,2
0,8
0,25
0,10
-
-
-
0,20
-
-
-
-
0,05
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,000 3 max. Be for welding electrode, welding rod and filler wire only.
11
EN 573-3:2013 (E)
Table 4 — Aluminium alloys — 4 000 series — Al Si Othersa
Allo y desig natio n Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Alum iniu m
Remarks Each
Total b
min.
-
0,05
0,15
Remainder
-
0,05
0,15
Remainder
-
0,05 Co
0,05
0,15
Remainder
-
-
-
0,05
0,15
Remainder
-
-
-
0,05
0,15
Remainder
-
-
-
-
0,05
0,15
Remainder
0,20
-
-
c
0,05
0,15
Remainder
-
-
-
0,05
0,15
Remainder Remainder
Numerical
Chemical symbols
EN AW-4004
EN AW-Al Si10Mg1,5
9,0-10,5
0,8
0,25
0,10
1,0-2,0
-
-
0,20
-
-
-
EN AW-4006
EN AW-Al Si1Fe
0,8-1,2
0,50-0,8
0,10
0,05
0,01
0,20
-
0,05
-
-
-
EN AW-4007
EN AW-Al Si1,5Mn
1,0-1,7
0,40-1,0
0,20
0,8-1,5
0,20
0,05-0,25
0,15-0,7
0,10
0,10
-
EN AW-4015
EN AW-Al Si2Mn
1,4-2,2
0,7
0,20
0,6-1,2
0,10-0,50
-
-
0,20
-
EN AW-4016
EN AW-Al Si2MnZn
1,4-2,2
0,7
0,20
0,6-1,2
0,10
-
-
0,50-1,3
-
EN AW-4017
EN AW-Al SiMnMgCu
0,6-1,6
0,7
0,10-0,50
0,6-1,2
0,10-0,50
-
-
0,20
EN AW-4018
EN AW-Al Si7Mg
6,5-7,5
0,20
0,05
0,10
0,50-0,8
-
-
0,10
EN AW-4032
EN AW-Al Si12,5MgCuNi
11,0-13,5
1,0
0,50-1,3
-
0,8-1,3
0,10
0,50-1,3
0,25
-
EN AW-4043A
EN AW-Al Si5(A)
4,5-6,0
0,6
0,30
0,15
0,20
-
-
0,10
0,15
-
-
c
0,05
0,15
EN AW-4045
EN AW-Al Si10
9,0-11,0
0,8
0,30
0,05
0,05
-
-
0,10
0,20
-
-
-
0,05
0,15
Remainder
EN AW-4046
EN AW-Al Si10Mg
9,0-11,0
0,50
0,03
0,40
0,20-0,50
-
-
0,10
0,15
-
-
c
0,05
0,15
Remainder
EN AW-4047A
EN AW-Al Si12(A)
11,0-13,0
0,6
0,30
0,15
0,10
-
-
0,20
0,15
-
-
c
0,05
0,15
Remainder
EN AW-4104
EN AW-Al Si10MgBi
9,0-10,5
0,8
0,25
0,10
1,0-2,0
-
-
0,20
-
-
-
0,02-0,20 Bi
0,05
0,15
Remainder
EN AW-4115
EN AW-Al Si2MnMgCu
1,8-2,2
0,7
0,10-0,50
0,6-1,2
0,10-0,50
-
-
0,20
-
-
-
-
0,05
0,15
Remainder
EN AW-4343
EN AW-AI Si7,5
6,8-8,2
0,8
0,25
0,10
-
-
-
0,20
-
-
-
-
0,05
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,000 3 max. Be for welding electrode, welding rod and filler wire only.
11
EN 573-3:2013 (E)
Table 5 — Aluminium alloys — 5 000 000 series — Al Mg Others a
Allo y desig natio n Si
12
Fe
Cu Cu
Numerical
Chemical symbols
EN AW-5005
EN AW-Al Mg1(B)
0,30
0,7
0,20
EN AW-5005A
EN AW-Al Mg1(C)
0,30
0,45
EN AW-5006
EN AW-Al Mg1Mn0,5
0,40
0,80
EN AW-5010
EN AW-Al Mg0,5Mn
0,40
EN AW-5018
EN AW-Al Mg3Mn0,4
0,25
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Alumi nium
Remarks Each
Total b
-
-
-
-
0,05
0,15
Remainder
0,20
-
-
-
-
0,05
0,15
Remainder
0,25
0,10
-
-
-
0,05
0,15
Remainder
-
0,30
0,10
-
-
-
0,05
0,15
Remainder
0,30
-
0,20
0,15
-
-
0,20-0,6 Mn+Cr c
0,05
0,15
Remainder Remainder
0,20
0,50-1,1
0,10
-
0,25
0,05
0,15
0,7-1,1
0,10
-
0,10
0,40-0,8
0,8-1,3
0,10
-
0,7
0,25
0,10-0,30
0,20-0,6
0,15
0,40
0,05
0,20-0,6
2,6-3,6 2,6-3,6
min.
EN AW-5019
EN AW-Al Mg5
0,40
0,50
0,10
0,10-0,6
4,5-5,6 4,5-5,6
0,20
-
0,20
0,20
-
-
0,10-0,6 Mn+Cr
0,05
0,15
EN AW-5026
EN AW-Al Mg4,5MnSiFe
0,55-1,4
0,20-1,0
0,10-0,8
0,6-1,8
3,9-4,9
0,30
-
1,0
0,20
-
-
0,30Zr
0,05
0,15
Remainder
EN AW-5040
EN AW-Al Mg1,5Mn
0,30
0,7
0,25
0,9-1,4
1,0-1,5
0,10-0,30
-
0,25
-
-
-
-
0,05
0,15
Remainder Remainder
EN AW-5042
EN AW-Al Mg3,5Mn
0,20
0,35
0,15
0,20-0,50
3,0-4,0
0,10
-
0,25
0,10
-
-
-
0,05
0,15
EN AW-5049
EN AW-Al Mg2Mn0,8
0,40
0,50
0,10
0,50-1,1
1,6-2,5
0,30
-
0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5050
EN AW-Al Mg1,5(C)
0,40
0,7
0,20
0,10
1,1-1,8
0,10
-
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-5050A
EN AW-Al Mg1,5(D)
0,40
0,7
0,20
0,30
1,1-1,8
0,10
-
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-5051A
EN AW-Al Mg2(B)
0,30
0,45
0,05
0,25
1,4-2,1
0,30
-
0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5052
EN AW-Al Mg2,5
0,25
0,40
0,10
0,10
2,2-2,8
0,15-0,35
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-5058
EN AW-Al Mg5Pb1,5
0,40
0,50
0,10
0,20
4,5-5,6
0,10
-
0,20
0,20
-
-
1,2-1,8 Pb
0,05
0,15
Remainder
EN AW-5059
EN AW-Al Mg5,5MnZnZr
0,45
0,50
0,25
0,6-1,2
5,0-6,0
0,25
-
0,40-0,9
0,20
-
-
0,05-0,25Zr
0,05
0,15
Remainder
EN AW-5070
EN AW-Al Mg4MnZn
0,25
0,40
0,25
0,40-0,8
3,5-4,5
0,30
-
0,40-0,8
0,15
-
-
-
0,05
0,15
Remainder Remainder
EN AW-5082
EN AW-Al Mg4,5
0,20
0,35
0,15
0,15
4,0-5,0
0,15
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5083
EN AW-Al Mg4,5Mn0,7
0,40
0,40
0,10
0,40-1,0
4,0-4,9
0,05-0,25
-
0,25
0,15
-
-
-
0,05
0,15
Remainder
EN AW-5086
EN AW-Al Mg4
0,40
0,50
0,10
0,20-0,7
3,5-4,5
0,05-0,25
-
0,25
0,15
-
-
-
0,05
0,15 0,15
Remainder
EN AW-5087
EN AW-Al Mg4,5MnZr
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
0,10-0,20 Zr c
0,05
0,15
Remainder
EN AW-5088
EN AW-Al Mg5Mn0,4
0,20
0,10-0,35
0,25
0,20-0,50
4,7-5,5
0,15
-
0,20-0,40
-
-
-
0,15Zr
0,05
0,15
Remainder
EN AW-5110
EN AW-Al 99,85Mg0,5
0,08
0,08
-
0,03
0,30-0,6
-
-
0,05
0,02
-
-
-
0,02
-
Remainder
EN 573-3:2013 (E)
Table 5 — Aluminium alloys — 5 000 000 series — Al Mg Others a
Allo y desig natio n
Alumi nium
Si
Fe
Cu Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Remarks Each
Total b
min.
0,20
0,50-1,1
0,10
-
0,25
-
-
-
-
0,05
0,15
Remainder
Numerical
Chemical symbols
EN AW-5005
EN AW-Al Mg1(B)
0,30
0,7
0,20
EN AW-5005A
EN AW-Al Mg1(C)
0,30
0,45
0,05
0,15
0,7-1,1
0,10
-
0,20
-
-
-
-
0,05
0,15
Remainder
EN AW-5006
EN AW-Al Mg1Mn0,5
0,40
0,80
0,10
0,40-0,8
0,8-1,3
0,10
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5010
EN AW-Al Mg0,5Mn
0,40
0,7
0,25
0,10-0,30
0,20-0,6
0,15
-
0,30
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5018
EN AW-Al Mg3Mn0,4
0,25
0,40
0,05
0,20-0,6
2,6-3,6 2,6-3,6
0,30
-
0,20
0,15
-
-
0,20-0,6 Mn+Cr c
0,05
0,15
Remainder Remainder
EN AW-5019
EN AW-Al Mg5
0,40
0,50
0,10
0,10-0,6
4,5-5,6 4,5-5,6
0,20
-
0,20
0,20
-
-
0,10-0,6 Mn+Cr
0,05
0,15
EN AW-5026
EN AW-Al Mg4,5MnSiFe
0,55-1,4
0,20-1,0
0,10-0,8
0,6-1,8
3,9-4,9
0,30
-
1,0
0,20
-
-
0,30Zr
0,05
0,15
Remainder
EN AW-5040
EN AW-Al Mg1,5Mn
0,30
0,7
0,25
0,9-1,4
1,0-1,5
0,10-0,30
-
0,25
-
-
-
-
0,05
0,15
Remainder Remainder
EN AW-5042
EN AW-Al Mg3,5Mn
0,20
0,35
0,15
0,20-0,50
3,0-4,0
0,10
-
0,25
0,10
-
-
-
0,05
0,15
EN AW-5049
EN AW-Al Mg2Mn0,8
0,40
0,50
0,10
0,50-1,1
1,6-2,5
0,30
-
0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5050
EN AW-Al Mg1,5(C)
0,40
0,7
0,20
0,10
1,1-1,8
0,10
-
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-5050A
EN AW-Al Mg1,5(D)
0,40
0,7
0,20
0,30
1,1-1,8
0,10
-
0,25
-
-
-
-
0,05
0,15
Remainder
EN AW-5051A
EN AW-Al Mg2(B)
0,30
0,45
0,05
0,25
1,4-2,1
0,30
-
0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5052
EN AW-Al Mg2,5
0,25
0,40
0,10
0,10
2,2-2,8
0,15-0,35
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-5058
EN AW-Al Mg5Pb1,5
0,40
0,50
0,10
0,20
4,5-5,6
0,10
-
0,20
0,20
-
-
1,2-1,8 Pb
0,05
0,15
Remainder
EN AW-5059
EN AW-Al Mg5,5MnZnZr
0,45
0,50
0,25
0,6-1,2
5,0-6,0
0,25
-
0,40-0,9
0,20
-
-
0,05-0,25Zr
0,05
0,15
Remainder
EN AW-5070
EN AW-Al Mg4MnZn
0,25
0,40
0,25
0,40-0,8
3,5-4,5
0,30
-
0,40-0,8
0,15
-
-
-
0,05
0,15
Remainder Remainder
EN AW-5082
EN AW-Al Mg4,5
0,20
0,35
0,15
0,15
4,0-5,0
0,15
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5083
EN AW-Al Mg4,5Mn0,7
0,40
0,40
0,10
0,40-1,0
4,0-4,9
0,05-0,25
-
0,25
0,15
-
-
-
0,05
0,15
Remainder
EN AW-5086
EN AW-Al Mg4
0,40
0,50
0,10
0,20-0,7
3,5-4,5
0,05-0,25
-
0,25
0,15
-
-
-
0,05
0,15 0,15
Remainder
EN AW-5087
EN AW-Al Mg4,5MnZr
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
0,10-0,20 Zr c
0,05
0,15
Remainder
EN AW-5088
EN AW-Al Mg5Mn0,4
0,20
0,10-0,35
0,25
0,20-0,50
4,7-5,5
0,15
-
0,20-0,40
-
-
-
0,15Zr
0,05
0,15
Remainder
EN AW-5110
EN AW-Al 99,85Mg0,5
0,08
0,08
-
0,03
0,30-0,6
-
-
0,05
0,02
-
-
-
0,02
-
Remainder
12
EN 573-3:2013 (E)
Table 5 — Aluminium alloy s — 5 000 series — Al Mg (continued) Mg (continued) Others a
Allo y desig natio n Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Numerical
Chemical symbols
EN AW-5119
EN AW-Al Mg5(A)
0,25
0,40
0,05
0,20-0,6
4,5-5,6
0,30
-
0,20
0,15
EN AW-5119A
EN AW Al Mg5(B)
0,25
0,40
0,05
0,20-0,6
4,5-5,6
0,30
-
0,20
0,15
Ga
-
V
-
Alum iniu m
Remarks Each
Total b
0,20-0,6 Mn+Cr c
0,05
0,15
Remainder
0,20-0,6 Mn+Cr e
0,05
0,15
Remainder
min.
EN AW-5149
EN AW-Al Mg2Mn0,8(A)
0,25
0,40
0,05
0,50-1,1
1,6-2,5
0,30
-
0,20
0,15
-
-
-
0,05
0,15
Remainder
EN AW-5154A
EN AW-Al Mg3,5(A)
0,50
0,50
0,10
0,50
3,1-3,9
0,25
-
0,20
0,20
-
-
0,10-0,50 Mn+Cr c
0,05
0,15
Remainder
EN AW-5154B
EN AW-Al Mg3,5Mn0,3
0,35
0,45
0,05
0,15-0,45
3,2-3,8
0,10
0,01
0,15
0,15
-
-
-
0,05
0,15
Remainder
EN AW-5182
EN AW-Al Mg4,5Mn0,4
0,20
0,35
0,15
0,20-0,50
4,0-5,0
0,10
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5183
EN AW-Al Mg4,5Mn0,7(A)
0,40
0,40
0,10
0,50-1,0
4,3-5,2
0,05-0,25
-
0,25
0,15
-
-
c
0,05
0,15
Remainder
EN AW-5183A
EN AW-Al Mg4,5Mn0,7(C) Mg4,5Mn0,7(C)
0,40
0,40
0,10
0,50-1,0
4,3-5,2
0,05-0,25
-
0,25
0,15
-
-
e
0,05
0,15
Remainder
EN AW-5186
EN AW-Al Mg4Mn0,4
0,40
0,45
0,25
0,20-0,50
3,8-4,8
0,15
-
0,40
0,15
-
-
0,05 Zr
0,05
0,15
Remainder
EN AW-5187
EN AW-Al Mg4,5MnZr
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
0,10-0,20 Zr e
0,05
0,15
Remainder
EN AW-5210
EN AW-Al 99,9Mg0,5
0,06
0,04
-
0,03
0,35-0,6
-
-
0,04
0,01
-
-
-
0,01
-
Remainder
EN AW-5249
EN AW-Al Mg2Mn0,8Zr
0,25
0,40
0,05
0,50-1,1
1,6-2,5
0,30
-
0,20
0,15
-
-
0,10-0,20 Zr c
0,05
0,15
Remainder
EN AW-5251
EN AW-Al Mg2Mn0,3
0,40
0,50
0,15
0,10-0,50
1,7-2,4
0,15
-
0,15
0,15
-
-
-
0,05
0,15 0,15
Remainder Remainder
EN AW-5252
EN AW-Al Mg2,5(B)
0,08
0,10
0,10
0,10
2,2-2,8
-
-
0,05
-
-
0,05
-
0,03
0,10
Remainder
EN AW-5283A
EN AW-Al Mg4,5Mn0,7(B)
0,30
0,30
0,03
0,50-1,0
4,5-5,1
0,05
0,03
0,10
0,03
-
-
0,05 Zr d
0,05
0,15
Remainder
EN AW-5305
EN AW-Al 99,85Mg1
0,08
0,08
-
0,03
0,7-1,1
-
0,05
0,02
-
-
-
0,02
-
Remainder
EN AW-5310
EN AW-Al 99,98Mg0,5
0,01
0,008
Remainder
EN AW-5352
EN AW-Al Mg2,5(A)
EN AW-5354
EN AW-Al Mg2,5MnZr
0,25
EN AW-5356
EN AW-Al Mg5Cr(A)
0,25
-
-
0,35-0,6
-
-
0,01
0,008
-
-
0,008 Fe+Ti
0,003
-
0,10
0,10
2,2-2,8
0,10 0,10
-
0,10 0,10
0,10
-
-
-
0,05
0,15
Remainder
0,40
0,05
0,50-1,0
2,4-3,0
0,05-0,20
-
0,25
0,15
-
-
0,10-0,20 Zr
0,05
0,15
Remainder
0,40
0,10
0,05-0,20
4,5-5,5 4,5-5,5
0,05-0,20
-
0,10
0,06-0,20
-
-
c
0,05
0,15
Remainder
0,05
0,15
Remainder
0,15
Remainder Remainder
0,45 Si+Fe
EN AW-5356A
EN AW-Al Mg5Cr(B)
0,25
0,40
0,10
0,05-0,20
4,5-5,5
0,05-0,20
-
0,10
0,06-0,20 0,06-0,20
-
-
e
EN AW-5383
EN AW-Al Mg4,5Mn0,9
0,25
0,25
0,20
0,7-1,0
4,0-5,2
0,25
-
0,40
0,15
-
-
0,20 Zr
0,05
EN AW-5449
EN AW-Al Mg2Mn0,8(B)
0,40
0,7
0,30
0,6-1,1
1,6-2,6
0,30
-
0,30
0,10
-
-
-
0,05
0,15 0,15
EN AW-5449A
EN AW-Al Mg2Mn0,8(C)
0,6
1,20
0,30
0,6-1,1
1,6-2,6
0,30
0,10
0,30
0,10
-
-
0,10 Sn
0,05
0,15
Remainder
EN AW-5454
EN AW-Al Mg3Mn
0,25
0,40
0,10
0,50-1,0
2,4-3,0
0,05-0,20
-
0,25
0,20
-
-
-
0,05
0,15
Remainder
EN AW-5456
EN AW-Al Mg5Mn1
0,25
0,40
0,10
0,50-1,0
4,7-5,5
0,05-0,20
-
0,25
0,20
-
-
-
0,05
0,15
Remainder
13
EN 573-3:2013 (E)
Table 5 — Aluminium alloy s — 5 000 series — Al Mg (continued) Mg (continued) Others a
Allo y desig natio n Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Each
Total b
min.
c
0,20-0,6 Mn+Cr
0,05
0,15
Remainder
0,20-0,6 Mn+Cr e
0,05
0,15
Remainder
Chemical symbols -
-
Alum iniu m
Remarks
EN AW-5119
EN AW-Al Mg5(A)
0,25
0,40
0,05
0,20-0,6
4,5-5,6
0,30
-
0,20
0,15
EN AW-5119A
EN AW Al Mg5(B)
0,25
0,40
0,05
0,20-0,6
4,5-5,6
0,30
-
0,20
0,15
EN AW-5149
EN AW-Al Mg2Mn0,8(A)
0,25
0,40
0,05
0,50-1,1
1,6-2,5
0,30
-
0,20
0,15
-
-
-
0,05
0,15
Remainder
EN AW-5154A
EN AW-Al Mg3,5(A)
0,50
0,50
0,10
0,50
3,1-3,9
0,25
-
0,20
0,20
-
-
0,10-0,50 Mn+Cr c
0,05
0,15
Remainder
EN AW-5154B
EN AW-Al Mg3,5Mn0,3
0,35
0,45
0,05
0,15-0,45
3,2-3,8
0,10
0,01
0,15
0,15
-
-
-
0,05
0,15
Remainder
EN AW-5182
EN AW-Al Mg4,5Mn0,4
0,20
0,35
0,15
0,20-0,50
4,0-5,0
0,10
-
0,25
0,10
-
-
-
0,05
0,15
Remainder
EN AW-5183
EN AW-Al Mg4,5Mn0,7(A)
0,40
0,40
0,10
0,50-1,0
4,3-5,2
0,05-0,25
-
0,25
0,15
-
-
c
0,05
0,15
Remainder
EN AW-5183A
EN AW-Al Mg4,5Mn0,7(C) Mg4,5Mn0,7(C)
0,40
0,40
0,10
0,50-1,0
4,3-5,2
0,05-0,25
-
0,25
0,15
-
-
e
0,05
0,15
Remainder
EN AW-5186
EN AW-Al Mg4Mn0,4
0,40
0,45
0,25
0,20-0,50
3,8-4,8
0,15
-
0,40
0,15
-
-
0,05 Zr
0,05
0,15
Remainder
EN AW-5187
EN AW-Al Mg4,5MnZr
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
0,10-0,20 Zr e
0,05
0,15
Remainder
EN AW-5210
EN AW-Al 99,9Mg0,5
0,06
0,04
-
0,03
0,35-0,6
-
-
0,04
0,01
-
-
-
0,01
-
Remainder
EN AW-5249
EN AW-Al Mg2Mn0,8Zr
0,25
0,40
0,05
0,50-1,1
1,6-2,5
0,30
-
0,20
0,15
-
-
0,10-0,20 Zr c
0,05
0,15
Remainder
EN AW-5251
EN AW-Al Mg2Mn0,3
0,40
0,50
0,15
0,10-0,50
1,7-2,4
0,15
-
0,15
0,15
-
-
-
0,05
0,15 0,15
Remainder Remainder
EN AW-5252
EN AW-Al Mg2,5(B)
0,08
0,10
0,10
0,10
2,2-2,8
-
-
0,05
-
-
0,05
-
0,03
0,10
Remainder
EN AW-5283A
EN AW-Al Mg4,5Mn0,7(B)
0,30
0,30
0,03
0,50-1,0
4,5-5,1
0,05
0,03
0,10
0,03
-
-
0,05 Zr d
0,05
0,15
Remainder
EN AW-5305
EN AW-Al 99,85Mg1
0,08
0,08
-
0,03
0,7-1,1
-
0,05
0,02
-
-
-
0,02
-
Remainder
EN AW-5310
EN AW-Al 99,98Mg0,5
0,01
0,008
Remainder
EN AW-5352
EN AW-Al Mg2,5(A)
EN AW-5354
EN AW-Al Mg2,5MnZr
0,25
-
-
0,35-0,6
-
-
0,01
0,008
-
-
0,008 Fe+Ti
0,003
-
0,10
0,10
2,2-2,8
0,10 0,10
-
0,10 0,10
0,10
-
-
-
0,05
0,15
Remainder
0,40
0,05
0,50-1,0
2,4-3,0
0,05-0,20
-
0,25
0,15
-
-
0,10-0,20 Zr
0,05
0,15
Remainder Remainder
0,45 Si+Fe
EN AW-5356
EN AW-Al Mg5Cr(A)
0,25
0,40
0,10
0,05-0,20
4,5-5,5 4,5-5,5
0,05-0,20
-
0,10
0,06-0,20
-
-
c
0,05
0,15
EN AW-5356A
EN AW-Al Mg5Cr(B)
0,25
0,40
0,10
0,05-0,20
4,5-5,5
0,05-0,20
-
0,10
0,06-0,20 0,06-0,20
-
-
e
0,05
0,15
Remainder
EN AW-5383
EN AW-Al Mg4,5Mn0,9
0,25
0,25
0,20
0,7-1,0
4,0-5,2
0,25
-
0,40
0,15
-
-
0,20 Zr
0,05
0,15
Remainder Remainder
EN AW-5449
EN AW-Al Mg2Mn0,8(B)
0,40
0,7
0,30
0,6-1,1
1,6-2,6
0,30
-
0,30
0,10
-
-
-
0,05
0,15 0,15
EN AW-5449A
EN AW-Al Mg2Mn0,8(C)
0,6
1,20
0,30
0,6-1,1
1,6-2,6
0,30
0,10
0,30
0,10
-
-
0,10 Sn
0,05
0,15
Remainder
EN AW-5454
EN AW-Al Mg3Mn
0,25
0,40
0,10
0,50-1,0
2,4-3,0
0,05-0,20
-
0,25
0,20
-
-
-
0,05
0,15
Remainder
EN AW-5456
EN AW-Al Mg5Mn1
0,25
0,40
0,10
0,50-1,0
4,7-5,5
0,05-0,20
-
0,25
0,20
-
-
-
0,05
0,15
Remainder
13
EN 573-3:2013 (E)
Table 5 — Aluminium alloy s — 5 000 series — Al Mg (continued) Allo y desig natio n Numerical
Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Others a
Remarks
Chemical symbols
Aluminium
Each
Total
b
min.
EN AW-5456A
EN AW-Al Mg5Mn1(A)
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
c
0,05
0,15
EN AW-5456B
EN AW-Al Mg5Mn1(B)
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
e
0,05
0,15
Remainder
EN AW-5505
EN AW-Al 99,9Mg1
0,06
0,04
-
0,03
0,8-1,1
-
0,04
0,01
-
-
-
0,01
-
Remainder
EN AW-5554
EN AW-Al Mg3Mn(A)
0,25
0,40
0,10
0,50-1,0
2,4-3,0
-
0,25
0,05-0,20
-
-
c
0,05
0,15
Remainder
0,05-0,20
Remainder
EN AW-5556A
EN AW-Al Mg5Mn
0,25
0,40
0,10
0,6-1,0
5,0-5,5
0,05-0,20
-
0,20
0,05-0,20
-
-
c
0,05
0,15
Remainder
EN AW-5556B
EN AW-Al Mg5Mn(A)
0,25
0,40
0,10
0,6-1,0
5,0-5,5
0,05-0,20
-
0,20
0,05-0,20
-
-
e
0,05
0,15
Remainder
EN AW-5605
EN AW-Al 99,98Mg1
0,01
0,008
-
-
0,8-1,1
-
0,01
0,008
-
-
0,008 Fe+Ti
0,003
-
Remainder
EN AW-5654
EN AW-Al Mg3,5Cr
0,45 Si+Fe
0,05
0,01
3,1-3,9
0,15-0,35
-
0,20
0,05-0,15
-
-
c
0,05
0,15
Remainder
EN AW-5654A
EN AW-Al Mg3,5Cr(A)
0,45 Si+Fe
0,05
0,01
3,1-3,9
0,15-0,35
-
0,20
0,05-0,15
-
-
e
0,05
0,15
Remainder
EN AW-5657
EN AW-Al 99,85Mg1(A)
0,08
0,10
0,10
0,03
0,6-1,0
-
-
0,05
-
0,03
0,05
-
0,02
0,05
Remainder
EN AW-5754
EN AW-Al Mg3
0,40
0,40
0,10
0,50
2,6-3,6
0,30
-
0,20
0,15
-
-
0,05
0,15
Remainder
0,10-0,6 Mn+Cr
c
a
"Others" includes listed elements elements for which no specific specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse analyse samples for trace elements elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of those "Others" metallic elements 0,010 % or more each, expressed expressed to the the second decimal place before determining the sum.
c
0,000 3 max. Be for welding electrode, electrode, welding welding rod and filler filler wire only.
d
0,003 max. Pb.
e
0,000 5 % max Be for welding electrode, welding rod and filler wire.
14
EN 573-3:2013 (E)
Table 5 — Aluminium alloy s — 5 000 series — Al Mg (continued) Allo y desig natio n Numerical
Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Others a
Remarks
Chemical symbols
Aluminium
Each
Total b
min. Remainder
EN AW-5456A
EN AW-Al Mg5Mn1(A)
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
c
0,05
0,15
EN AW-5456B
EN AW-Al Mg5Mn1(B)
0,25
0,40
0,05
0,7-1,1
4,5-5,2
0,05-0,25
-
0,25
0,15
-
-
e
0,05
0,15
Remainder
EN AW-5505
EN AW-Al 99,9Mg1
0,06
0,04
-
0,03
0,8-1,1
-
0,04
0,01
-
-
-
0,01
-
Remainder
EN AW-5554
EN AW-Al Mg3Mn(A)
0,25
0,40
0,10
0,50-1,0
2,4-3,0
0,05-0,20
-
0,25
0,05-0,20
-
-
c
0,05
0,15
Remainder
EN AW-5556A
EN AW-Al Mg5Mn
0,25
0,40
0,10
0,6-1,0
5,0-5,5
0,05-0,20
-
0,20
0,05-0,20
-
-
c
0,05
0,15
Remainder
EN AW-5556B
EN AW-Al Mg5Mn(A)
0,25
0,40
0,10
0,6-1,0
5,0-5,5
0,05-0,20
-
0,20
0,05-0,20
-
-
e
0,05
0,15
Remainder
EN AW-5605
EN AW-Al 99,98Mg1
0,01
0,008
-
-
0,8-1,1
-
0,01
0,008
-
-
0,008 Fe+Ti
0,003
-
Remainder
EN AW-5654
EN AW-Al Mg3,5Cr
0,45 Si+Fe
0,05
0,01
3,1-3,9
0,15-0,35
-
0,20
0,05-0,15
-
-
c
0,05
0,15
Remainder
EN AW-5654A
EN AW-Al Mg3,5Cr(A)
0,45 Si+Fe
0,05
0,01
3,1-3,9
0,15-0,35
-
0,20
0,05-0,15
-
-
e
0,05
0,15
Remainder
EN AW-5657
EN AW-Al 99,85Mg1(A)
0,10
0,03
0,6-1,0
-
-
0,05
-
0,03
0,05
-
0,02
0,05
Remainder
0,05
0,15
Remainder
EN AW-5754
EN AW-Al Mg3
0,08 0,40
0,10 0,40
0,10
0,50
2,6-3,6
0,30
-
0,20
0,15
-
-
0,10-0,6 Mn+Cr
c
a
"Others" includes listed elements elements for which no specific specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse analyse samples for trace elements elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of those "Others" metallic elements 0,010 % or more each, expressed expressed to the the second decimal place before determining the sum.
c
0,000 3 max. Be for welding electrode, electrode, welding welding rod and filler filler wire only.
d
0,003 max. Pb.
e
0,000 5 % max Be for welding electrode, welding rod and filler wire.
14
EN 573-3:2013 (E)
Table 6 — Aluminium alloys — 6 000 series — Al MgSi Others a
Allo y desi gnati on Si Numerical
Chemical symbols
EN AW-6003
EN AW-Al Mg1Si0,8
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
0,35-1,0
0,6
0,10
0,8
0,8-1,5
0,35 0,35
-
0,20 0,20
0,10
Ga
V
-
-
Alumi nium
Remarks Each
Total b
-
0,05
0,15
Remainder
min.
EN AW-6005
EN AW-Al SiMg
0,6-0,9
0,35
0,10
0,10
0,40-0,6
0,10
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6005A
EN AW-Al SiMg(A)
0,50-0,9
0,35
0,30
0,50
0,40-0,7
0,30
-
0,20
0,10
-
-
0,12-0,50 Mn+Cr
0,05
0,15
Remainder
EN AW-6005B
EN AW-Al SiMg(B)
0,45-0,8
0,30
0,10
0,10
0,40-0,8
0,10
-
0,10
0,10
-
-
-
0,05
0,15 0,15
Remainder
EN AW-6008
EN AW-Al SiMgV
0,50-0,9
0,35
0,30
0,30
0,40-0,7 0,40-0,7
0,30 0,30
-
0,20
0,10
-
0,05-0,20
-
0,05
0,15
Remainder
EN AW-6011
EN AW-Al Mg0,9Si0,9Cu
0,6-1,2
1,0
0,40-0,9
0,8
0,6-1,2
0,30
0,20
1,5
0,20
-
-
-
0,05
0,15
Remainder
-
-
0,7 Bi; 0,40-2,0 Pb
0,05
0,15
Remainder
0,7 Bi; 0,40-2,0 Sn
0,05
0,15
Remainder
-
0,05
0,15
Remainder
EN AW-6012
EN AW-Al MgSiPb
0,6-1,4
0,50
0,10
0,40-1,0
0,6-1,2 0,6-1,2
0,30
-
0,30
0,20
EN AW-6012A
EN AW-Al MgSiSn
0,6-1,4
0,50
0,40
0,20-1,0
0,6-1,2
0,30
-
0,30
0,20
EN AW-6013
EN AW-Al Mg1Si0,8CuMn
0,6-1,0
0,50
0,6-1,1
0,20-0,8
0,8-1,2
0,10
-
0,25
0,10
-
-
EN AW-6014
EN AW-Al Mg0,6Si0,6V
0,30-0,6
0,35
0,25
0,05-0,20 0,05-0,20
0,40-0,8
0,20
-
0,10
0,10
-
0,05-0,20
-
0,05
0,15
Remainder
EN AW-6015
EN AW-Al Mg1Si0,3Cu
0,20-0,40
0,10-0,30
0,10-0,25
0,10
0,8-1,1
0,10
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6016
EN AW-Al Si1,2Mg0,4
1,0-1,5
0,50
0,20
0,20
0,25-0,6
0,10
-
0,20
0,15
-
-
0,05
0,15
Remainder
EN AW-6018
EN AW-Al Mg1SiPbMn
0,50-1,2
0,7
0,15-0,40
0,30-0,8
0,6-1,2 0,6-1,2
0,10
-
0,30
0,20
-
-
c
0,05
0,15
Remainder
EN AW-6023
EN AW-Al Si1Sn1MgBi
0,6-1,4
0,50
0,20-0,50
0,20-0,6
0,40-0,9
-
-
-
-
-
-
0,30-0,8 Bi, 0,6-1,2 Sn
0,05
0,15
Remainder
EN AW-6025
EN AW-Al Mg2,5SiMnCu
0,8-1,5
0,7
0,20-0,7
0,6-1,4
2,1-3,0
0,20
-
0,50
0,20
-
-
-
0,05
0,15
Remainder
-
-
0,60-1,40 Si; 0,50-1,5 Bi; 0,40 Pb; 0,05 Sn
0,05
0,15
Remainder Remainder
EN AW-6026
EN AW-Al MgSiBi
EN AW-6056
EN AW-Al Si1MgCuMn
EN AW-6060
EN AW-Al MgSi
EN AW-6061
EN AW-Al Mg1SiCu
0,40-0,8
EN AW-6061A
EN AW-Al Mg1SiCu(A)
EN AW-6063
EN AW-Al Mg0,7Si
EN AW-6063A
EN AW-Al Mg0,7Si(A)
EN AW-6064A
EN AW-Al Mg1SiBi
EN AW-6065
EN AW-Al Mg1Bi1Si
0,60-1,40
0,70
0,20-0,50
0,20-1,0
0,7-1,3
0,50
0,50-1,1
0,30-0,6
0,10-0,30
0,10
0,7
0,15-0,40
0,40-0,8
0,7
0,15-0,40
0,20-0,6
0,35
0,10
0,30-0,6
0,15-0,35
0,10
0,40-0,80
0,7
0,15-0,40
0,40-0,8
0,7
0,15-0,40
0,60-1,2
0,30
-
0,30
0,40-1,0
0,6-1,2
0,25
-
0,10-0,7
d
-
-
d
0,05
0,15
0,10
0,35-0,6
0,05
-
0,15
0,10
-
-
-
0,05
0,15
Remainder
0,15
0,8-1,2
0,04-0,35
-
0,25
0,15
-
-
-
0,05
0,15
Remainder
0,15
0,8-1,2
0,04-0,35
-
0,25
0,15
-
-
e
0,05
0,15
Remainder
0,10
0,45-0,9
0,10
-
0,10
0,10
-
-
-
0,05
0,15 0,15
Remainder
0,15
0,6-0,9
0,05
-
0,15
0,10
-
-
-
0,05
0,15
Remainder
0,15
0,8-1,2
0,04-0,14
-
0,25
0,15
-
-
-
0,05
0,15
Remainder
-
0,50-1,5 Bi;0,05 Pb; 0,15 Zr
0,05
0,15
Remainder
0,15
0,8-1,2
0,15
-
0,25
0,20
0,10
-
15
EN 573-3:2013 (E)
Table 6 — Aluminium alloys — 6 000 series — Al MgSi Others a
Allo y desi gnati on Numerical
Chemical symbols
EN AW-6003
EN AW-Al Mg1Si0,8
Alumi nium
Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Remarks Each
Total b
min.
0,35-1,0
0,6
0,10
0,8
0,8-1,5
0,35 0,35
-
0,20 0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6005
EN AW-Al SiMg
0,6-0,9
0,35
0,10
0,10
0,40-0,6
0,10
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6005A
EN AW-Al SiMg(A)
0,50-0,9
0,35
0,30
0,50
0,40-0,7
0,30
-
0,20
0,10
-
-
0,12-0,50 Mn+Cr
0,05
0,15
Remainder
EN AW-6005B
EN AW-Al SiMg(B)
0,45-0,8
0,30
0,10
0,10
0,40-0,8
0,10
-
0,10
0,10
-
-
-
0,05
0,15 0,15
Remainder
EN AW-6008
EN AW-Al SiMgV
0,50-0,9
0,35
0,30
0,30
0,40-0,7 0,40-0,7
0,30 0,30
-
0,20
0,10
-
0,05-0,20
-
0,05
0,15
Remainder
EN AW-6011
EN AW-Al Mg0,9Si0,9Cu
0,6-1,2
1,0
0,40-0,9
0,8
0,6-1,2
0,30
0,20
1,5
0,20
-
-
-
0,05
0,15
Remainder
-
-
0,7 Bi; 0,40-2,0 Pb
0,05
0,15
Remainder
0,7 Bi; 0,40-2,0 Sn
0,05
0,15
Remainder
-
0,05
0,15
Remainder
EN AW-6012
EN AW-Al MgSiPb
0,6-1,4
0,50
0,10
0,40-1,0
0,6-1,2 0,6-1,2
0,30
-
0,30
0,20
EN AW-6012A
EN AW-Al MgSiSn
0,6-1,4
0,50
0,40
0,20-1,0
0,6-1,2
0,30
-
0,30
0,20
EN AW-6013
EN AW-Al Mg1Si0,8CuMn
0,6-1,0
0,50
0,6-1,1
0,20-0,8
0,8-1,2
0,10
-
0,25
0,10
-
-
EN AW-6014
EN AW-Al Mg0,6Si0,6V
0,30-0,6
0,35
0,25
0,05-0,20 0,05-0,20
0,40-0,8
0,20
-
0,10
0,10
-
0,05-0,20
-
0,05
0,15
Remainder
EN AW-6015
EN AW-Al Mg1Si0,3Cu
0,20-0,40
0,10-0,30
0,10-0,25
0,10
0,8-1,1
0,10
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6016
EN AW-Al Si1,2Mg0,4
1,0-1,5
0,50
0,20
0,20
0,25-0,6
0,10
-
0,20
0,15
-
-
0,05
0,15
Remainder
EN AW-6018
EN AW-Al Mg1SiPbMn
0,50-1,2
0,7
0,15-0,40
0,30-0,8
0,6-1,2 0,6-1,2
0,10
-
0,30
0,20
-
-
c
0,05
0,15
Remainder
EN AW-6023
EN AW-Al Si1Sn1MgBi
0,6-1,4
0,50
0,20-0,50
0,20-0,6
0,40-0,9
-
-
-
-
-
-
0,30-0,8 Bi, 0,6-1,2 Sn
0,05
0,15
Remainder
EN AW-6025
EN AW-Al Mg2,5SiMnCu
0,8-1,5
0,7
0,20-0,7
0,6-1,4
2,1-3,0
0,20
-
0,50
0,20
-
-
-
0,05
0,15
Remainder
EN AW-6026
EN AW-Al MgSiBi
0,60-1,40
0,70
0,20-0,50
0,20-1,0
0,60-1,2
0,30
-
0,30
0,20
-
-
0,60-1,40 Si; 0,50-1,5 Bi; 0,40 Pb; 0,05 Sn
0,05
0,15
Remainder
EN AW-6056
EN AW-Al Si1MgCuMn
0,7-1,3
0,50
0,50-1,1
0,40-1,0
0,6-1,2
0,25
-
0,10-0,7
d
-
-
d
0,05
0,15
Remainder
EN AW-6060
EN AW-Al MgSi
0,30-0,6
0,10-0,30
0,10
0,10
0,35-0,6
0,05
-
0,15
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6061
EN AW-Al Mg1SiCu
0,40-0,8
0,7
0,15-0,40
0,15
0,8-1,2
0,04-0,35
-
0,25
0,15
-
-
-
0,05
0,15
Remainder
EN AW-6061A
EN AW-Al Mg1SiCu(A)
0,40-0,8
0,7
0,15-0,40
0,15
0,8-1,2
0,04-0,35
-
0,25
0,15
-
-
e
0,05
0,15
Remainder
EN AW-6063
EN AW-Al Mg0,7Si
0,20-0,6
0,35
0,10
0,10
0,45-0,9
0,10
-
0,10
0,10
-
-
-
0,05
0,15 0,15
Remainder
EN AW-6063A
EN AW-Al Mg0,7Si(A)
0,30-0,6
0,15-0,35
0,10
0,15
0,6-0,9
0,05
-
0,15
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6064A
EN AW-Al Mg1SiBi
0,40-0,80
0,7
0,15-0,40
0,15
0,8-1,2
0,04-0,14
-
0,25
0,15
-
-
-
0,05
0,15
Remainder
-
0,50-1,5 Bi;0,05 Pb; 0,15 Zr
0,05
0,15
Remainder
EN AW-6065
EN AW-Al Mg1Bi1Si
0,40-0,8
0,7
0,15-0,40
0,15
0,8-1,2
0,15
-
0,25
0,10
-
15
EN 573-3:2013 (E)
Table 6 — Aluminium alloys — 6 000 series series — Al MgSi (continued) Others a
Allo y desi gnati on Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Numerical
Chemical symbols
EN AW-6081
EN AW-Al Si0,9MgMn
0,7-1,1
0,50
0,10
0,10-0,45
0,6-1,0
0,10
-
0,20
EN AW-6082
EN AW-Al Si1MgMn
0,7-1,3
0,50
0,10
0,40-1,0
0,6-1,2
0,25
-
EN AW-6082A
EN AW-Al Si1MgMn(A)
0,7-1,3
0,50
0,10
0,40-1,0
0,6-1,2
0,25
-
EN AW-6101
EN AW-Al MgSi
0,30-0,7
0,50
0,10
0,03
0,35-0,8
0,03
-
0,10
-
EN AW-6101A
EN AW-Al MgSi(A)
0,30-0,7
0,40
0,05
-
0,40-0,9
-
-
-
-
Ga
V
Alumi nium
Remarks Each
Total b
-
0,05
0,15
-
-
0,05
0,15
Remainder
-
e
0,05
0,15
Remainder
-
-
0,06 B
0,03
0,10
Remainder Remainder
-
-
-
0,03
0,10
Remainder
0,15
-
-
0,20
0,10
-
0,20
0,10
-
min. Remainder
EN AW-6101B
EN AW-Al MgSi(B)
0,30-0,6
0,10-0,30
0,05
0,05
0,35-0,6
-
-
0,10
-
-
-
-
0,03
0,10
Remainder
EN AW-6106
EN AW-Al MgSiMn
0,30-0,6
0,35
0,25
0,05-0,20
0,40-0,8
0,20
-
0,10
-
-
-
-
0,05
0,10
Remainder
EN AW-6110A
EN AW-Al Mg0,9Si0,9MnCu
0,7-1,1
0,50
0,30-0,8
0,30-0,9
0,7-1,1
0,05-0,25
-
0,20
-
-
-
0,20 Ti+Zr
0,05
0,15
Remainder
EN AW-6181
EN AW-Al SiMg0,8
0,8-1,2
0,45
0,10
0,15
0,6-1,0
0,10
-
0,20 0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6182
EN AW-Al Si1MgZr
0,9-1,3
0,50
0,10
0,50-1,0
0,7-1,2
0,25
-
0,20
0,10
-
-
0,05-0,20Zr
0,05
0,15
Remainder
EN AW-6201
EN AW-Al Mg0,7Si
0,50-0,9
0,50
0,10
0,03
0,6-0,9
0,03
-
0,10
-
-
-
0,06 B
0,03
0,10
Remainder
EN AW-6261
EN AW-Al Mg1SiCuMn
0,40-0,7
0,40
0,15-0,40
0,20-0,35
0,7-1,0
0,10
-
0,20
0,10
-
-
-
0,05
0,15
Remainder Remainder
EN AW-6262
EN AW-Al Mg1SiPb
0,40-0,8
0,7
0,15-0,40
0,15
0,8-1,2
0,04-0,14
-
0,25
0,15
-
-
f
0,05
0,15
EN AW-6262A
EN AW-Al Mg1SiSn
0,40-0,8
0,7
0,15-0,40
0,15
0,8-1,2
0,04-0,14
-
0,25
0,10
-
-
0,40-0,9Bi;0,40-1,0Sn 0,40-0,9Bi;0,40-1,0Sn
0,05
0,15
Remainder
EN AW-6351
EN AW-Al SiMg0,5Mn
0,7-1,3
0,50
0,10
0,40-0,8
0,40-0,8
-
-
0,20
0,20
-
-
-
0,05
0,15
Remainder
EN AW-6351A
EN AW-Al SiMg0,5Mn(A)
0,7-1,3
0,50
0,10
0,40-0,8
0,40-0,8
-
-
0,20
0,20
-
-
e
0,05
0,15
Remainder
EN AW-6360
EN AW-Al SiMgMn
0,35-0,8
0,10-0,30
0,15
0,02-0,15
0,25-0,45
0,05
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6401
EN AW-Al 99,9MgSi
0,35-0,7
0,04
0,05-0,20
0,03
0,35-0,7
-
-
0,04
0,01
-
-
-
0,01
-
Remainder
EN AW-6463
EN AW-Al Mg0,7Si(B)
0,20-0,6
0,15
0,20
0,05
0,45-0,9
-
-
0,05
-
-
-
-
0,05
0,15
Remainder
EN AW-6951
EN AW-Al MgSi0,3Cu
0,20-0,50
0,8
0,15-0,40
0,10
0,40-0,8
-
-
0,20
-
-
-
-
0,05
0,15 0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,40-0,7 Bi; 0,40-1,2 Pb.
d
0,20 max. Zr + Ti.
e
0,003 max. Pb.
f
0,40-0,7 Bi; 0,40-0,7 Pb.
16
EN 573-3:2013 (E)
Table 6 — Aluminium alloys — 6 000 series series — Al MgSi (continued) Others a
Allo y desi gnati on
Alumi nium
Si
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Remarks Each
Total b
min.
0,15
-
-
-
0,05
0,15
Remainder
Numerical
Chemical symbols
EN AW-6081
EN AW-Al Si0,9MgMn
0,7-1,1
0,50
0,10
0,10-0,45
0,6-1,0
0,10
-
0,20
EN AW-6082
EN AW-Al Si1MgMn
0,7-1,3
0,50
0,10
0,40-1,0
0,6-1,2
0,25
-
0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6082A
EN AW-Al Si1MgMn(A)
0,7-1,3
0,50
0,10
0,40-1,0
0,6-1,2
0,25
-
0,20
0,10
-
-
e
0,05
0,15
Remainder
EN AW-6101
EN AW-Al MgSi
0,30-0,7
0,50
0,10
0,03
0,35-0,8
0,03
-
0,10
-
-
-
0,06 B
0,03
0,10
Remainder Remainder
EN AW-6101A
EN AW-Al MgSi(A)
0,30-0,7
0,40
0,05
-
0,40-0,9
-
-
-
-
-
-
-
0,03
0,10
Remainder
EN AW-6101B
EN AW-Al MgSi(B)
0,30-0,6
0,10-0,30
0,05
0,05
0,35-0,6
-
-
0,10
-
-
-
-
0,03
0,10
Remainder
EN AW-6106
EN AW-Al MgSiMn
0,30-0,6
0,35
0,25
0,05-0,20
0,40-0,8
0,20
-
0,10
-
-
-
-
0,05
0,10
Remainder
EN AW-6110A
EN AW-Al Mg0,9Si0,9MnCu
0,7-1,1
0,50
0,30-0,8
0,30-0,9
0,7-1,1
0,05-0,25
-
0,20
-
-
-
0,20 Ti+Zr
0,05
0,15
Remainder
EN AW-6181
EN AW-Al SiMg0,8
0,8-1,2
0,45
0,10
0,15
0,6-1,0
0,10
-
0,20 0,20
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6182
EN AW-Al Si1MgZr
0,9-1,3
0,50
0,10
0,50-1,0
0,7-1,2
0,25
-
0,20
0,10
-
-
0,05-0,20Zr
0,05
0,15
Remainder
EN AW-6201
EN AW-Al Mg0,7Si
0,50-0,9
0,50
0,10
0,03
0,6-0,9
0,03
-
0,10
-
-
-
0,06 B
0,03
0,10
Remainder
EN AW-6261
EN AW-Al Mg1SiCuMn
0,40-0,7
0,40
0,15-0,40
0,20-0,35
0,7-1,0
0,10
-
0,20
0,10
-
-
-
0,05
0,15
Remainder Remainder
EN AW-6262
EN AW-Al Mg1SiPb
0,40-0,8
0,7
0,15-0,40
0,15
0,8-1,2
0,04-0,14
-
0,25
0,15
-
-
f
0,05
0,15
EN AW-6262A
EN AW-Al Mg1SiSn
0,40-0,8
0,7
0,15-0,40
0,15
0,8-1,2
0,04-0,14
-
0,25
0,10
-
-
0,40-0,9Bi;0,40-1,0Sn 0,40-0,9Bi;0,40-1,0Sn
0,05
0,15
Remainder
EN AW-6351
EN AW-Al SiMg0,5Mn
0,7-1,3
0,50
0,10
0,40-0,8
0,40-0,8
-
-
0,20
0,20
-
-
-
0,05
0,15
Remainder
EN AW-6351A
EN AW-Al SiMg0,5Mn(A)
0,7-1,3
0,50
0,10
0,40-0,8
0,40-0,8
-
-
0,20
0,20
-
-
e
0,05
0,15
Remainder
EN AW-6360
EN AW-Al SiMgMn
0,35-0,8
0,10-0,30
0,15
0,02-0,15
0,25-0,45
0,05
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-6401
EN AW-Al 99,9MgSi
0,35-0,7
0,04
0,05-0,20
0,03
0,35-0,7
-
-
0,04
0,01
-
-
-
0,01
-
Remainder
EN AW-6463
EN AW-Al Mg0,7Si(B)
0,20-0,6
0,15
0,20
0,05
0,45-0,9
-
-
0,05
-
-
-
-
0,05
0,15
Remainder
EN AW-6951
EN AW-Al MgSi0,3Cu
0,20-0,50
0,8
0,15-0,40
0,10
0,40-0,8
-
-
0,20
-
-
-
-
0,05
0,15 0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,40-0,7 Bi; 0,40-1,2 Pb.
d
0,20 max. Zr + Ti.
e
0,003 max. Pb.
f
0,40-0,7 Bi; 0,40-0,7 Pb.
16
EN 573-3:2013 (E)
Table 7 — Aluminium alloys — 7 000 series series — Al Zn Others a
Allo y desi gnati on Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Alumi nium
Remarks
Chemical symbols
Each
Total b
min.
EN AW-7003
EN AW-Al Zn6Mg0,8Zr
0,30
0,35
0,20
0,30
0,50-1,0
0,20
-
5,0-6,5
0,20
-
-
0,05-0,25 Zr
0,05
0,15
Remainder
EN AW-7005
EN AW-Al Zn4,5Mg1,5Mn
0,35
0,40
0,10
0,20-0,7
1,0-1,8
0,06-0,20
-
4,0-5,0
0,01-0,06
-
-
0,08-0,20 Zr
0,05
0,15
Remainder
EN AW-7009
EN AW-Al Zn5,5MgCuAg
0,20
0,20
0,6-1,3
0,10
2,1-2,9
0,10-0,25
-
5,5-6,5
0,20
-
-
c
0,05
0,15
Remainder
EN AW-7010
EN AW-Al Zn6MgCu
0,12
0,15
1,5-2,0
0,10
2,1-2,6
0,05
0,05
5,7-6,7
0,06
-
-
0,10-0,16 Zr
0,05
0,15
Remainder
EN AW-7012
EN AW-Al Zn6Mg2Cu
0,15
0,25
0,8-1,2
0,08-0,15
1,8-2,2 1,8-2,2
0,04
-
5,8-6,5
0,02-0,08
-
-
0,10-0,18 Zr
0,05
0,15
Remainder
EN AW-7015
EN AW-Al Zn5Mg1,5CuZr
0,20
0,30
0,06-0,15 0,06-0,15
0,10
1,3-2,1
0,15
-
4,6-5,2
0,10
-
-
0,10-0,20 Zr
0,05
0,15
Remainder
EN AW-7016
EN AW-Al Zn4,5Mg1Cu
0,10
0,12
0,45-1,0
0,03
0,8-1,4
-
-
4,0-5,0
0,03
-
0,05
-
0,03
0,10
Remainder
EN AW-7019
EN AW-Al Zn4Mg2
0,35
0,45
0,20
0,15-0,50
1,5-2,5
0,20
0,10
3,5-4,5
0,15
-
-
0,10-0,25 Zr
0,05
0,15
Remainder
EN AW-7020
EN AW-Al Zn4,5Mg1
0,35
0,40
0,20
0,05-0,50
1,0-1,4
0,10-0,35
-
4,0-5,0
-
-
-
d
0,05
0,15
Remainder
EN AW-7021
EN AW-Al Zn5,5Mg1,5
0,25
0,40
0,25
0,10
1,2-1,8
0,05
-
5,0-6,0
0,10
-
-
0,08-0,18 Zr
0,05
0,15
Remainder
EN AW-7022
EN AW-Al Zn5Mg3Cu
0,50
0,50
0,50-1,0
0,10-0,40
2,6-3,7
0,10-0,30
-
4,3-5,2
-
-
-
0,20 Ti+Zr
0,05
0,15
Remainder
EN AW-7026
EN AW-Al Zn5Mg1,5Cu
0,08
0,12
0,6-0,9
0,05-0,20
1,5-1,9
-
-
4,6-5,2
0,05
-
-
0,09-0,14 Zr
0,03
0,10
Remainder
EN AW-7029
EN AW-Al Zn4,5Mg1,5Cu
0,10
0,12
0,50-0,9
0,03
1,3-2,0
-
-
4,2-5,2
0,05
-
0,05
-
0,03
0,10
Remainder
EN AW-7030
EN AW-Al Zn5,5Mg1Cu
0,20
0,30
0,20-0,40
0,05
1,0-1,5
0,04
-
4,8-5,9
0,03
0,03
-
0,03 Zr
0,05
0,15
Remainder
EN AW-7039
EN AW-Al Zn4Mg3
0,30
0,40
0,10
0,10-0,40
2,3-3,3
0,15-0,25
-
3,4-4,5
0,10
-
-
-
0,05
0,15
Remainder
EN AW-7049A
EN AW-Al Zn8MgCu
0,40
0,50
1,2-1,9
0,50
2,1-3,1
0,05-0,25
-
7,2-8,4
-
-
-
0,25 Zr+Ti
0,05
0,15
Remainder
EN AW-7050
EN AW-Al Zn6CuMgZr
0,12
0,15
2,0-2,6
0,10
1,9-2,6
0,04
-
5,7-6,7
0,06
-
-
0,08-0,15 Zr
0,05
0,15
Remainder
EN AW-7060
EN AW-Al Zn7CuMg
0,15
0,20
1,8-2,6
0,20
1,3-2,1
0,15-0,25
-
6,1-7,5
0,05
-
-
0,05 Zr e
0,05
0,15
Remainder
EN AW-7072
EN AW-Al Zn1
0,10
0,10
0,10
-
-
0,8-1,3
-
-
-
-
0,05
0,15
Remainder
EN AW-7075
EN AW-Al Zn5,5MgCu
0,40
0,50
1,2-2,0
0,30
2,1-2,9
0,18-0,28
-
5,1-6,1
0,20
-
-
f
0,05
0,15
Remainder
EN AW-7108
EN AW-Al Zn5Mg1Zr
0,10
0,10
0,05
0,05
0,7-1,4
-
-
4,5-5,5
0,05
-
-
0,12-0,25 Zr
0,05
0,15
Remainder
EN AW-7108A
EN AW-Al Zn5Mg1Zr
0,20
0,30
0,05
0,05
0,7-1,5
0,04
-
4,8-5,8
0,03
0,03
-
0,15-0,25Zr
0,05
0,15
Remainder Remainder
0,7 Si+Fe
EN AW-7116
EN AW-Al Zn4,5Mg1Cu0,8
0,15
0,30
0,50-1,1 0,50-1,1
0,05
0,8-1,4
-
-
4,2-5,2
0,05
0,03
0,05
-
0,05
0,15
EN AW-7129
EN AW-Al Zn4,5Mg1,5Cu(A) Zn4,5Mg1,5Cu(A)
0,15
0,30
0,50-0,9
0,10
1,3-2,0
0,10
-
4,2-5,2
0,05
0,03
0,05
-
0,05
0,15
Remainder
EN AW-7149
EN AW-Al Zn8MgCu(A)
0,15
0,20
1,2-1,9
0,20
2,0-2,9
0,10-0,22
-
7,2-8,2
0,10
-
-
-
0,05
0,15 0,15
Remainder
EN AW-7150
EN AW-Al Zn6CuMgZr(A)
0,12
0,15
1,9-2,5
0,10
2,0-2,7
0,04
-
5,9-6,9
0,06
-
-
0,08-0,15 Zr
0,05
0,15
Remainder
17
EN 573-3:2013 (E)
Table 7 — Aluminium alloys — 7 000 series series — Al Zn Others a
Allo y desi gnati on Si
Fe
Numerical
Chemical symbols
EN AW-7003
EN AW-Al Zn6Mg0,8Zr
0,30
0,35
EN AW-7005
EN AW-Al Zn4,5Mg1,5Mn
0,35
EN AW-7009
EN AW-Al Zn5,5MgCuAg
0,20
EN AW-7010
EN AW-Al Zn6MgCu
EN AW-7012
EN AW-Al Zn6Mg2Cu
EN AW-7015 EN AW-7016 EN AW-7019
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Alumi nium
Remarks Each
Total b
-
5,0-6,5
0,20
-
-
0,05-0,25 Zr
0,05
0,15
0,06-0,20
-
4,0-5,0
0,01-0,06
-
-
0,08-0,20 Zr
0,05
0,15
Remainder
0,10-0,25
-
5,5-6,5
0,20
-
-
c
0,05
0,15
Remainder
2,1-2,6
0,05
0,05
5,7-6,7
0,06
-
-
0,10-0,16 Zr
0,05
0,15
Remainder
1,8-2,2 1,8-2,2
0,04
-
5,8-6,5
0,02-0,08
-
-
0,10-0,18 Zr
0,05
0,15
Remainder
0,10
1,3-2,1
0,15
-
4,6-5,2
0,10
-
-
0,10-0,20 Zr
0,05
0,15
Remainder
0,03
0,8-1,4
-
-
4,0-5,0
0,03
-
0,05
-
0,03
0,10
Remainder
1,5-2,5
0,20
0,10
3,5-4,5
0,15
-
-
0,10-0,25 Zr
0,05
0,15
Remainder
0,20
0,30
0,50-1,0
0,20
0,40
0,10
0,20-0,7
1,0-1,8
0,20
0,6-1,3
0,10
2,1-2,9
0,12
0,15
1,5-2,0
0,10
0,15
0,25
0,8-1,2
0,08-0,15
EN AW-Al Zn5Mg1,5CuZr
0,20
0,30
0,06-0,15 0,06-0,15
EN AW-Al Zn4,5Mg1Cu
0,10
0,12
0,45-1,0
EN AW-Al Zn4Mg2
0,35
0,45
0,20
0,15-0,50
min. Remainder
EN AW-7020
EN AW-Al Zn4,5Mg1
0,35
0,40
0,20
0,05-0,50
1,0-1,4
0,10-0,35
-
4,0-5,0
-
-
-
d
0,05
0,15
Remainder
EN AW-7021
EN AW-Al Zn5,5Mg1,5
0,25
0,40
0,25
0,10
1,2-1,8
0,05
-
5,0-6,0
0,10
-
-
0,08-0,18 Zr
0,05
0,15
Remainder
EN AW-7022
EN AW-Al Zn5Mg3Cu
0,50
0,50
0,50-1,0
0,10-0,40
2,6-3,7
0,10-0,30
-
4,3-5,2
-
-
-
0,20 Ti+Zr
0,05
0,15
Remainder
EN AW-7026
EN AW-Al Zn5Mg1,5Cu
0,08
0,12
0,6-0,9
0,05-0,20
1,5-1,9
-
-
4,6-5,2
0,05
-
-
0,09-0,14 Zr
0,03
0,10
Remainder
EN AW-7029
EN AW-Al Zn4,5Mg1,5Cu
0,10
0,12
0,50-0,9
0,03
1,3-2,0
-
-
4,2-5,2
0,05
-
0,05
-
0,03
0,10
Remainder
EN AW-7030
EN AW-Al Zn5,5Mg1Cu
0,20
0,30
0,20-0,40
0,05
1,0-1,5
0,04
-
4,8-5,9
0,03
0,03
-
0,03 Zr
0,05
0,15
Remainder
EN AW-7039
EN AW-Al Zn4Mg3
0,30
0,40
0,10
0,10-0,40
2,3-3,3
0,15-0,25
-
3,4-4,5
0,10
-
-
-
0,05
0,15
Remainder
EN AW-7049A
EN AW-Al Zn8MgCu
0,40
0,50
1,2-1,9
0,50
2,1-3,1
0,05-0,25
-
7,2-8,4
-
-
-
0,25 Zr+Ti
0,05
0,15
Remainder
EN AW-7050
EN AW-Al Zn6CuMgZr
0,12
0,15
2,0-2,6
0,10
1,9-2,6
0,04
-
5,7-6,7
0,06
-
-
0,08-0,15 Zr
0,05
0,15
Remainder
EN AW-7060
EN AW-Al Zn7CuMg
0,15
0,20
1,8-2,6
0,20
1,3-2,1
0,15-0,25
-
6,1-7,5
0,05
-
-
0,05 Zr e
0,05
0,15
Remainder
EN AW-7072
EN AW-Al Zn1
0,10
0,10
0,10
-
-
0,8-1,3
-
-
-
-
0,05
0,15
Remainder
EN AW-7075
EN AW-Al Zn5,5MgCu
0,40
0,50
1,2-2,0
0,30
2,1-2,9
0,18-0,28
-
5,1-6,1
0,20
-
-
f
0,05
0,15
Remainder
EN AW-7108
EN AW-Al Zn5Mg1Zr
0,10
0,10
0,05
0,05
0,7-1,4
-
-
4,5-5,5
0,05
-
-
0,12-0,25 Zr
0,05
0,15
Remainder
EN AW-7108A
EN AW-Al Zn5Mg1Zr
0,20
0,30
0,05
0,05
0,7-1,5
0,04
-
4,8-5,8
0,03
0,03
-
0,15-0,25Zr
0,05
0,15
Remainder Remainder
0,7 Si+Fe
EN AW-7116
EN AW-Al Zn4,5Mg1Cu0,8
0,15
0,30
0,50-1,1 0,50-1,1
0,05
0,8-1,4
-
-
4,2-5,2
0,05
0,03
0,05
-
0,05
0,15
EN AW-7129
EN AW-Al Zn4,5Mg1,5Cu(A) Zn4,5Mg1,5Cu(A)
0,15
0,30
0,50-0,9
0,10
1,3-2,0
0,10
-
4,2-5,2
0,05
0,03
0,05
-
0,05
0,15
Remainder
EN AW-7149
EN AW-Al Zn8MgCu(A)
0,15
0,20
1,2-1,9
0,20
2,0-2,9
0,10-0,22
-
7,2-8,2
0,10
-
-
-
0,05
0,15 0,15
Remainder
EN AW-7150
EN AW-Al Zn6CuMgZr(A)
0,12
0,15
1,9-2,5
0,10
2,0-2,7
0,04
-
5,9-6,9
0,06
-
-
0,08-0,15 Zr
0,05
0,15
Remainder
17
EN 573-3:2013 (E)
Table 7 — Aluminium alloy s — 7 000 series series — Al Zn (continued) Others a
Allo y desi gnati on Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Chemical symbols 0,15
0,20
1,2-2,0
0,10
2,1-2,9
0,18-0,28
-
5,1-6,1
0,10
-
-
Alumi nium
Remarks
-
Each
Total b
min.
0,05
0,15
Remainder
EN AW-7175
EN AW-Al Zn5,5MgCu(B)
EN AW-7178
EN AW-Al Zn7MgCu
0,40
0,50
1,6-2,4
0,30
2,4-3,1
0,18-0,28
-
6,3-7,3
0,20
-
-
-
0,05
0,15
Remainder
EN AW-7475
EN AW-Al Zn5,5MgCu(A)
0,10
0,12
1,2-1,9
0,06
1,9-2,6
0,18-0,25
-
5,2-6,2
0,06
-
-
-
0,05
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,25-0,40 Ag.
d
0,08-0,20 Zr; 0,08-0,25 Zr + Ti.
e
0,003 max. Pb.
f
Zr + Ti limit of 0,25 maximum may be used for extruded and forged products if mutually agreed by supplier or manufacturer and purchaser.
18
EN 573-3:2013 (E)
Table 7 — Aluminium alloy s — 7 000 series series — Al Zn (continued) Others a
Allo y desi gnati on Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni
Zn
Ti
Ga
V
Alumi nium
Remarks
Chemical symbols
Each
Total b
min. Remainder
EN AW-7175
EN AW-Al Zn5,5MgCu(B)
0,15
0,20
1,2-2,0
0,10
2,1-2,9
0,18-0,28
-
5,1-6,1
0,10
-
-
-
0,05
0,15
EN AW-7178
EN AW-Al Zn7MgCu
0,40
0,50
1,6-2,4
0,30
2,4-3,1
0,18-0,28
-
6,3-7,3
0,20
-
-
-
0,05
0,15
Remainder
EN AW-7475
EN AW-Al Zn5,5MgCu(A)
0,10
0,12
1,2-1,9
0,06
1,9-2,6
0,18-0,25
-
5,2-6,2
0,06
-
-
-
0,05
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
0,25-0,40 Ag.
d
0,08-0,20 Zr; 0,08-0,25 Zr + Ti.
e
0,003 max. Pb.
f
Zr + Ti limit of 0,25 maximum may be used for extruded and forged products if mutually agreed by supplier or manufacturer and purchaser.
18
EN 573-3:2013 (E)
Table 8 — Aluminium alloys — 8 000 series — Miscellaneous Others a
Allo y desig natio n Si Numerical
Fe
Cu
Mn
Mg
Cr
Ni Ni
Zn
Ti
Ga
V
Alumi nium
Remarks
Chemical symbols
Each
Total b
min.
EN AW-8006
EN AW-Al Fe1,5Mn
0,40
1,2-2,0
0,30 0,30
0,30-1,0
0,10
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-8008
EN AW-Al Fe1Mn0,8
0,6
0,9-1,6
0,20
0,50-1,0
-
-
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-8011A
EN AW-Al FeSi(A)
0,40-0,8
0,50-1,0
0,10
0,10
0,10
0,10
-
0,10
0,05 0,05
-
-
-
0,05
0,15
Remainder
EN AW-8014
EN AW-Al Fe1,5Mn0,4
0,30
1,2-1,6
0,20
0,20-0,6
0,10
-
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-8015
EN AW-Al FeMn0,3
0,30
0,8-1,4
0,10
0,10-0,40
0,10
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-8016
EN AW-Al Fe1Mn
0,20
0,7-1,1
0,10
0,10-0,30 0,10-0,30
0,10
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-8018
EN AW-Al FeSiCu
0,50-0,9
0,6-1,0
0,30-0,6
0,30
-
-
-
-
0,006-0,06
-
-
-
0,05
0,15
Remainder
EN AW-8021B
EN AW-Al Fe1,5
0,40
1,1-1,7
0,05
0,03
0,01
0,03
-
0,05
0,05
-
-
-
0,03
0,10
Remainder
EN AW-8030
EN AW-Al FeCu
0,10
0,30-0,8
0,15-0,30
–
0,05
–
–
0,05
–
–
–
0,001-0,04B
0,03
0,10
Remainder
EN AW-8079
EN AW-Al Fe1Si
0,05-0,30
0,7-1,3
0,05
-
-
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-8090
EN AW-Al Li2,5Cu1,5Mg1
0,20
0,30
1,0-1,6
0,10
0,6-1,3
0,10
-
0,25
0,10
-
-
0,04-0,16 Zr c
0,05
0,15
Remainder
EN AW-8111
EN AW-Al FeSi(B)
0,30-1,1
0,40-1,0
0,10
0,10
0,05
0,05
-
0,10
0,08
-
-
-
0,05
0,15
Remainder
EN AW-8112
EN AW-Al 95
1,0
1,0
0,40
0,6
0,7
0,20
-
1,0
0,20
-
-
-
0,05
0,15
Remainder
EN AW-8176
EN AW-Al FeSi
0,03-0,15
0,40-1,0
–
–
–
–
–
0,10
–
0,03
–
–
0,05
0,15
Remainder
EN AW-8211
EN AW-Al FeSi(C)
0,40-0,8
0,50-1,0
0,10
0,05-0,20
0,10
0,15
-
0,10
0,05
-
-
-
0,06
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
2,2-2,7 Li.
19
EN 573-3:2013 (E)
Table 8 — Aluminium alloys — 8 000 series — Miscellaneous Others a
Allo y desig natio n Si
Fe
Cu
Mn
Mg
Cr
Ni Ni
Zn
Ti
Ga
V
Alumi nium
Remarks
Numerical
Chemical symbols
Each
Total b
EN AW-8006
EN AW-Al Fe1,5Mn
0,40
1,2-2,0
0,30 0,30
0,30-1,0
0,10
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-8008
EN AW-Al Fe1Mn0,8
0,6
0,9-1,6
0,20
0,50-1,0
-
-
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-8011A
EN AW-Al FeSi(A)
0,40-0,8
0,50-1,0
0,10
0,10
0,10
0,10
-
0,10
0,05 0,05
-
-
-
0,05
0,15
Remainder
EN AW-8014
EN AW-Al Fe1,5Mn0,4
0,30
1,2-1,6
0,20
0,20-0,6
0,10
-
-
0,10
0,10
-
-
-
0,05
0,15
Remainder
EN AW-8015
EN AW-Al FeMn0,3
0,30
0,8-1,4
0,10
0,10-0,40
0,10
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-8016
EN AW-Al Fe1Mn
0,20
0,7-1,1
0,10
0,10-0,30 0,10-0,30
0,10
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
min.
EN AW-8018
EN AW-Al FeSiCu
0,50-0,9
0,6-1,0
0,30-0,6
0,30
-
-
-
-
0,006-0,06
-
-
-
0,05
0,15
Remainder
EN AW-8021B
EN AW-Al Fe1,5
0,40
1,1-1,7
0,05
0,03
0,01
0,03
-
0,05
0,05
-
-
-
0,03
0,10
Remainder
EN AW-8030
EN AW-Al FeCu
0,10
0,30-0,8
0,15-0,30
–
0,05
–
–
0,05
–
–
–
0,001-0,04B
0,03
0,10
Remainder
EN AW-8079
EN AW-Al Fe1Si
0,05-0,30
0,7-1,3
0,05
-
-
-
-
0,10
-
-
-
-
0,05
0,15
Remainder
EN AW-8090
EN AW-Al Li2,5Cu1,5Mg1
0,20
0,30
1,0-1,6
0,10
0,6-1,3
0,10
-
0,25
0,10
-
-
0,04-0,16 Zr c
0,05
0,15
Remainder
EN AW-8111
EN AW-Al FeSi(B)
0,30-1,1
0,40-1,0
0,10
0,10
0,05
0,05
-
0,10
0,08
-
-
-
0,05
0,15
Remainder Remainder
EN AW-8112
EN AW-Al 95
1,0
1,0
0,40
0,6
0,7
0,20
-
1,0
0,20
-
-
-
0,05
0,15
EN AW-8176
EN AW-Al FeSi
0,03-0,15
0,40-1,0
–
–
–
–
–
0,10
–
0,03
–
–
0,05
0,15
Remainder
EN AW-8211
EN AW-Al FeSi(C)
0,40-0,8
0,50-1,0
0,10
0,05-0,20
0,10
0,15
-
0,10
0,05
-
-
-
0,06
0,15
Remainder
a
"Others" includes listed elements for which which no specific limit is shown as well as unlisted metallic metallic elements. The producer may analyse samples for trace elements not specified in the registration registration or specification. However, However, such analysis is not required and may not cover all metallic "Other" elements. Should any analysis by the producer or the purchaser establish that an "Others" element exceeds the limit of "Each" or that the aggregate of several "Others" elements exceeds the limit of "Total", the material shall be considered non-conforming.
b
The sum of of those "Others" "Others" metallic metallic elements 0,010 % or more more each, expressed expressed to the second decimal place before determining the sum.
c
2,2-2,7 Li.
19
BS EN 573-3:2013
EN 573-3:2013 (E)
An n ex A (normative) Form of products
A.1 Gener al Table A.1 to Table A.8 give, for each major field of application, the availability of each alloy. The last column indicates whether the alloy is in conformity [Y or N (Yes or No)] with EN 602, 602, which specifies the requirements for the chemical composition of wrought aluminium and wrought aluminium alloys used for the production of materials and articles intended to be in contact with foodstuff.
A.2 Eur opean op ean St andard and ard s The European Standards specifying mechanical properties for the product groups according to Table A.1 to Table A.8 are the following: f ollowing: EN 485-2, 485-2, EN 541, 541, EN 546-2, 546-2, EN 570, 570, EN 586-2, 586-2, EN 603-2, 603-2, EN 683-2, 683-2, EN 754-2, 754-2, EN 755-2, 755-2, EN 1301-2, 1301-2, EN 1592-2, 1592-2, EN 1715-2, 1715-2, EN 1715-3 and 1715-3 and EN 1715-4. 1715-4.
BS EN 573-3:2013
EN 573-3:2013 (E)
An n ex A (normative) Form of products
A.1 Gener al Table A.1 to Table A.8 give, for each major field of application, the availability of each alloy. The last column indicates whether the alloy is in conformity [Y or N (Yes or No)] with EN 602, 602, which specifies the requirements for the chemical composition of wrought aluminium and wrought aluminium alloys used for the production of materials and articles intended to be in contact with foodstuff.
A.2 Eur opean op ean St andard and ard s The European Standards specifying mechanical properties for the product groups according to Table A.1 to Table A.8 are the following: f ollowing: EN 485-2, 485-2, EN 541, 541, EN 546-2, 546-2, EN 570, 570, EN 586-2, 586-2, EN 603-2, 603-2, EN 683-2, 683-2, EN 754-2, 754-2, EN 755-2, 755-2, EN 1301-2, 1301-2, EN 1592-2, 1592-2, EN 1715-2, 1715-2, EN 1715-3 and 1715-3 and EN 1715-4. 1715-4.
20
EN 573-3:2013 (E)
Table A.1 A.1 — Applications and fo rms of p roducts — 1 000 000 series
Allo y desi gnat ion
Numerical
Forgings and forging stock
Chemical symbols
Wire and drawing stock
Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil
Finstock
Sheet, strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
EN AW-1050A
EN AW-Al 99,5
X
-
X
X
X
X
X
X
X
X
X
-
Y
EN AW-1060
EN AW-Al 99,6
-
-
-
-
X
X
X
-
X
-
-
-
Y
EN AW-1070A
EN AW-Al 99,7
-
-
-
X
X
X
-
-
X
-
X
-
Y
EN AW-1080A
EN AW-Al 99,8(A)
-
-
X
X
X
X
-
-
X
-
X
-
Y
EN AW-1085
EN AW-Al 99,85
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-1090
EN AW-Al 99,90
-
-
-
X
-
-
-
-
-
-
-
-
Y
EN AW-1098
EN AW-Al 99,98
-
-
X
X
-
-
-
-
X
-
X
-
Y
EN AW-1100
EN AW-Al 99,0Cu
-
-
-
-
X
X
X
X
X
-
-
-
Y
EN AW-1110
EN AW-Al 99,1
-
X
-
-
-
-
-
-
-
-
-
-
Y
EN AW-1198
EN AW-Al 99,98(A)
-
-
-
-
-
-
X
-
X
-
-
-
Y
EN AW-1199
EN AW-Al 99,99
-
-
-
-
-
-
X
-
X
-
-
-
Y
EN AW-1200
EN AW-Al 99,0
-
-
-
X
X
X
X
X
X
-
X
-
Y
EN AW-1200A
EN AW-Al 99,0(A)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-1235
EN AW-Al 99,35
-
-
-
-
-
-
X
-
-
-
-
-
Y
EN AW-1350
EN AW-Al 99,5
-
X
-
-
X
X
-
-
-
-
-
-
Y
EN AW-1350A
EN AW-Al 99,5(A)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-1370
EN AW-Al 99,7
-
X
-
-
-
-
-
-
-
-
-
-
Y
EN AW-1450
EN AW-Al 99,5 Ti
-
-
X
-
-
-
-
-
-
-
-
-
Y
Y Yes X Applicable item
21
EN 573-3:2013 (E)
Table A.2 A.2 — Applications and fo rms of p roducts — 2 000 000 series Allo y desi gnat ion Numerical
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil
Finstock
Sheet, strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
EN AW-2001
EN AW-Al Cu5,5MgMn
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-2007
EN AW-Al Cu4PbMgMn
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-2011
EN AW-Al Cu6BiPb
X
-
-
X
X
X
-
-
-
-
X
-
N
EN AW-2011A
EN AW-Al Cu6BiPb(A)
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-2014
EN AW-Al Cu4SiMg
X
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-2014A
EN AW-Al Cu4SiMg(A)
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-2017A
EN AW-Al Cu4MgSi(A)
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-2024
EN AW-Al Cu4Mg1
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-2030
EN AW-Al Cu4PbMg
-
-
-
X
X
X
-
-
-
-
-
-
N
EN AW-2031
EN AW-Al Cu2,5NiMg
X
-
-
-
-
-
-
-
-
-
-
-
N
EN AW-2091
EN AW-Al Cu2Li2Mg1,5
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-2117
EN AW-Al Cu2,5Mg
-
-
-
X
-
-
-
-
X
-
-
-
N
EN AW-2124
EN AW-Al Cu4Mg1(A)
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-2214
EN AW-Al Cu4SiMg(B)
X
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-2219
EN AW-Al Cu6Mn
X
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-2319
EN AW-Al Cu6Mn(A)
-
-
X
-
-
-
-
-
-
-
-
-
N
EN AW-2618A
EN AW-Al Cu2Mg1,5Ni
X
-
-
-
X
X
-
-
X
-
-
-
N
N No X Applicable item
22
Chemical symbols
Forgi ngs and forging stock
EN 573-3:2013 (E)
Table A.2 A.2 — Applications and fo rms of p roducts — 2 000 000 series Allo y desi gnat ion
Forgi ngs and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
-
-
-
X
Extruded products X
Foil
Finstock
Sheet, strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
-
-
-
-
-
N
Numerical
Chemical symbols
EN AW-2001
EN AW-Al Cu5,5MgMn
EN AW-2007
EN AW-Al Cu4PbMgMn
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-2011
EN AW-Al Cu6BiPb
X
-
-
X
X
X
-
-
-
-
X
-
N
EN AW-2011A
EN AW-Al Cu6BiPb(A)
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-2014
EN AW-Al Cu4SiMg
X
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-2014A
EN AW-Al Cu4SiMg(A)
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-2017A
EN AW-Al Cu4MgSi(A)
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-2024
EN AW-Al Cu4Mg1
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-2030
EN AW-Al Cu4PbMg
-
-
-
X
X
X
-
-
-
-
-
-
N
EN AW-2031
EN AW-Al Cu2,5NiMg
X
-
-
-
-
-
-
-
-
-
-
-
N
EN AW-2091
EN AW-Al Cu2Li2Mg1,5
-
-
-
-
X
X
-
-
X
-
-
-
N N
-
-
EN AW-2117
EN AW-Al Cu2,5Mg
-
-
-
X
-
-
-
-
X
-
-
-
EN AW-2124
EN AW-Al Cu4Mg1(A)
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-2214
EN AW-Al Cu4SiMg(B)
X
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-2219
EN AW-Al Cu6Mn
X
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-2319
EN AW-Al Cu6Mn(A)
-
-
X
-
-
-
-
-
-
-
-
-
N
EN AW-2618A
EN AW-Al Cu2Mg1,5Ni
X
-
-
-
X
X
-
-
X
-
-
-
N
N No X Applicable item
22
EN 573-3:2013 (E)
Table A.3 A.3 — Applications and fo rms of p roducts — 3 000 000 series Allo y desi gnat ion
Forg ing s and forging stock
Wire and drawing stock Welding
Mechanical
Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Numerical
Chemical symbols
EN AW-3002
EN AW-Al Mn0,2Mg0,1
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-3003
EN AW-Al Mn1Cu
-
-
-
X
X
X
X
X
X
X
-
X
Y
EN AW-3004
EN AW-Al Mn1Mg1
-
-
-
-
-
-
-
X
X
X
-
X
Y
EN AW-3005
EN AW-Al Mn1Mg0,5
-
-
-
-
-
-
X
-
X
X
-
X
Y
EN AW-3005A
EN AW-Al Mn1Mg0,5(A)
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3017
EN AW-Al Mn1Cu0,3
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3102
EN AW-Al Mn0,2
-
-
-
-
X
X
-
-
-
-
X
-
N
EN AW-3103
EN AW-Al Mn1
-
-
X
X
X
X
X
X
X
X
X
X
Y
EN AW-3103A
EN AW-Al Mn1(A)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-3104
EN AW-Al Mn1Mg1Cu
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3105
EN AW-Al Mn0,5Mg0,5
-
-
-
-
-
-
X
X
X
-
-
X
N
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3105A EN AW-Al Mn0,5Mg0,5(A)
Electrical
Drawn products
EN AW-3105B
EN AW-Al Mn0,6Mg0,5
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-3207
EN AW-Al Mn0,6
-
-
-
-
-
-
-
-
X
X
X
-
Y
EN AW-3207A
EN AW-Al Mn0,6(A)
-
-
-
-
-
-
-
-
X
X
-
-
Y
Y Yes N No X Applicable item
23
EN 573-3:2013 (E)
Table A.3 A.3 — Applications and fo rms of p roducts — 3 000 000 series Allo y desi gnat ion Numerical
Chemical symbols
EN AW-3002
EN AW-Al Mn0,2Mg0,1
Forg ing s and forging stock -
Wire and drawing stock Extruded products
Foil
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Electrical
Welding
Mechanical
Drawn products
-
-
-
-
-
-
-
X
-
-
-
Y
Finstock
EN AW-3003
EN AW-Al Mn1Cu
-
-
-
X
X
X
X
X
X
X
-
X
Y
EN AW-3004
EN AW-Al Mn1Mg1
-
-
-
-
-
-
-
X
X
X
-
X
Y
EN AW-3005
EN AW-Al Mn1Mg0,5
-
-
-
-
-
-
X
-
X
X
-
X
Y
EN AW-3005A
EN AW-Al Mn1Mg0,5(A)
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3017
EN AW-Al Mn1Cu0,3
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3102
EN AW-Al Mn0,2
-
-
-
-
X
X
-
-
-
-
X
-
N
EN AW-3103
EN AW-Al Mn1
-
-
X
X
X
X
X
X
X
X
X
X
Y
EN AW-3103A
EN AW-Al Mn1(A)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-3104
EN AW-Al Mn1Mg1Cu
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3105
EN AW-Al Mn0,5Mg0,5
-
-
-
-
-
-
X
X
X
-
-
X
N
EN AW-3105A EN AW-Al Mn0,5Mg0,5(A)
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-3105B
EN AW-Al Mn0,6Mg0,5
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-3207
EN AW-Al Mn0,6
-
-
-
-
-
-
-
-
X
X
X
-
Y
EN AW-3207A
EN AW-Al Mn0,6(A)
-
-
-
-
-
-
-
-
X
X
-
-
Y
Y Yes N No X Applicable item
23
EN 573-3:2013 (E)
Table A.4 A.4 — Applications and fo rms of p roducts — 4 000 000 series Allo y desi gnat ion
Wire and drawing stock Electric al
Welding
Mechanical
Drawn products
Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Numerical
Chemical symbols
EN AW-4004
EN AW-Al Si10Mg1,5
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4006
EN AW-Al Si1Fe
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4007
EN AW-Al Si1,5Mn
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4015
EN AW-Al Si2Mn
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4016
EN AW-Al Si2MnZn
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-4017
EN AW-Al SiMnMgCu
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4018
EN AW-Al Si7Mg
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-4032
EN AW-Al Si12,5MgCuNi
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-4043A
EN AW-Al Si5(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-4045
EN AW-Al Si10
-
-
X
-
-
-
-
-
X
-
-
-
Y
EN AW-4046
EN AW-Al Si10Mg
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-4047A
EN AW-Al Si12(A)
-
-
X
-
-
-
-
-
X
-
-
-
Y
EN AW-4104
EN AW-Al Si10MgBi
-
-
-
X
-
-
-
-
X
-
-
-
N
-
-
-
N
-
-
-
Y
EN AW-4115
EN AW-Al Si2MnMgCu
-
-
-
-
-
-
-
-
X a
EN AW-4343
EN AW-AI Si7,5
-
-
-
-
-
-
-
-
X
a
Not applicable for plate.
Y Yes N No X Applicable item
24
Forg ing s and forging stock
EN 573-3:2013 (E)
Table A.4 A.4 — Applications and fo rms of p roducts — 4 000 000 series Allo y desi gnat ion
Forg ing s and forging stock
Wire and drawing stock Electric al
Welding
Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Mechanical
Drawn products
Electrowelded tube
Allo ys fo r foodstuff application
-
X
-
-
-
Y
Numerical
Chemical symbols
EN AW-4004
EN AW-Al Si10Mg1,5
-
-
-
-
-
-
-
EN AW-4006
EN AW-Al Si1Fe
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4007
EN AW-Al Si1,5Mn
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4015
EN AW-Al Si2Mn
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4016
EN AW-Al Si2MnZn
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-4017
EN AW-Al SiMnMgCu
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-4018
EN AW-Al Si7Mg
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-4032
EN AW-Al Si12,5MgCuNi
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-4043A
EN AW-Al Si5(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-4045
EN AW-Al Si10
-
-
X
-
-
-
-
-
X
-
-
-
Y
EN AW-4046
EN AW-Al Si10Mg
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-4047A
EN AW-Al Si12(A)
-
-
X
-
-
-
-
-
X
-
-
-
Y
EN AW-4104
EN AW-Al Si10MgBi
-
-
-
X
-
-
-
-
X
-
-
-
N
EN AW-4115
EN AW-Al Si2MnMgCu
-
-
-
-
-
-
-
-
X a
-
-
-
N
EN AW-4343
EN AW-AI Si7,5
-
-
-
-
-
-
-
-
X
-
-
-
Y
a
Not applicable for plate.
Y Yes N No X Applicable item
24
EN 573-3:2013 (E)
Table A.5 A.5 — Applications and fo rms of products — 5 000 000 series Allo y desi gnat ion Numerical
Chemical symbols
Forg ing s and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application Y
EN AW-5005
EN AW-Al Mg1(B)
-
-
-
X
X
X
-
X
X
-
-
X
EN AW-5005A
EN AW-Al Mg1(C)
-
-
-
-
X
X
-
-
X
-
X
-
Y
EN AW-5006
EN AW-Al Mg1Mn0,5
-
-
-
-
X
X
-
-
-
-
-
-
Y N
EN AW-5010
EN AW-Al Mg0,5Mn
-
-
-
-
-
-
-
-
X
-
-
-
EN AW-5018
EN AW-Al Mg3Mn0,4
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5019
EN AW-Al Mg5
X
-
-
X
X
X
-
-
-
-
-
-
Y
EN AW-5026
EN AW-Al Mg4,5MnSiFe
X
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5040
EN AW-Al Mg1,5Mn
-
-
-
-
-
-
-
-
-
X
-
X
Y
EN AW-5042
EN AW-Al Mg3,5Mn
-
-
-
-
-
-
-
-
-
X
-
-
Y
EN AW-5049
EN AW-Al Mg2Mn0,8
-
-
-
-
-
-
-
-
X
-
-
X
Y
EN AW-5449A
EN AW-Al Mg2Mn0,8(C)
-
-
-
-
-
-
-
-
X
-
-
X
N
EN AW-5050
EN AW-Al Mg1,5(C)
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-5050A
EN AW-Al Mg1,5(D)
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-5051A
EN AW-Al Mg2(B)
-
-
-
X
X
X
-
-
-
-
-
-
Y
EN AW-5052
EN AW-Al Mg2,5
-
-
-
X
X
X
-
-
X
X
-
X
Y
EN AW-5058
EN AW-Al Mg5Pb1,5
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-5059
EN AW-Al Mg5,5MnZnZr
X
-
X
-
-
-
-
-
X
-
-
-
Y
EN AW-5070
EN AW-Al Mg4MnZn
X
-
-
X
X
X
-
-
-
-
-
-
N Y
EN AW-5082
EN AW-Al Mg4,5
-
-
-
X
-
-
-
-
-
X
-
-
EN AW-5083
EN AW-Al Mg4,5Mn0,7
X
-
-
-
X
X
-
-
X
-
-
X
Y
EN AW-5086
EN AW-Al Mg4
-
-
-
X
X
X
-
-
X
-
-
X
Y
Y Yes N No X Applicable item
25
EN 573-3:2013 (E)
Table A.5 A.5 — Applications and fo rms of products — 5 000 000 series Allo y desi gnat ion Numerical
Chemical symbols
Forg ing s and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application Y
EN AW-5005
EN AW-Al Mg1(B)
-
-
-
X
X
X
-
X
X
-
-
X
EN AW-5005A
EN AW-Al Mg1(C)
-
-
-
-
X
X
-
-
X
-
X
-
Y
EN AW-5006
EN AW-Al Mg1Mn0,5
-
-
-
-
X
X
-
-
-
-
-
-
Y N
EN AW-5010
EN AW-Al Mg0,5Mn
-
-
-
-
-
-
-
-
X
-
-
-
EN AW-5018
EN AW-Al Mg3Mn0,4
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5019
EN AW-Al Mg5
X
-
-
X
X
X
-
-
-
-
-
-
Y
EN AW-5026
EN AW-Al Mg4,5MnSiFe
X
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5040
EN AW-Al Mg1,5Mn
-
-
-
-
-
-
-
-
-
X
-
X
Y
EN AW-5042
EN AW-Al Mg3,5Mn
-
-
-
-
-
-
-
-
-
X
-
-
Y
EN AW-5049
EN AW-Al Mg2Mn0,8
-
-
-
-
-
-
-
-
X
-
-
X
Y
EN AW-5449A
EN AW-Al Mg2Mn0,8(C)
-
-
-
-
-
-
-
-
X
-
-
X
N
EN AW-5050
EN AW-Al Mg1,5(C)
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-5050A
EN AW-Al Mg1,5(D)
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-5051A
EN AW-Al Mg2(B)
-
-
-
X
X
X
-
-
-
-
-
-
Y
EN AW-5052
EN AW-Al Mg2,5
-
-
-
X
X
X
-
-
X
X
-
X
Y
EN AW-5058
EN AW-Al Mg5Pb1,5
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-5059
EN AW-Al Mg5,5MnZnZr
X
-
X
-
-
-
-
-
X
-
-
-
Y
EN AW-5070
EN AW-Al Mg4MnZn
X
-
-
X
X
X
-
-
-
-
-
-
N Y
EN AW-5082
EN AW-Al Mg4,5
-
-
-
X
-
-
-
-
-
X
-
-
EN AW-5083
EN AW-Al Mg4,5Mn0,7
X
-
-
-
X
X
-
-
X
-
-
X
Y
EN AW-5086
EN AW-Al Mg4
-
-
-
X
X
X
-
-
X
-
-
X
Y
Y Yes N No X Applicable item
25
EN 573-3:2013 (E)
Table A.5 A.5 — Applications and fo rms of p roducts — 5 000 000 series (continued) Allo y desi gnat ion
26
Forg ing s and forging stock
Wire and drawing stock
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Electrical
Welding
Mechanical
-
-
X
-
-
-
-
-
-
-
-
-
Y
-
-
-
-
-
-
-
-
X
-
-
-
N
-
-
X
-
-
-
-
X
-
X
-
Y
-
X
-
-
-
-
-
-
-
-
-
Y
-
X
-
-
-
-
-
-
-
-
-
Y
-
-
X
-
-
-
-
-
-
-
-
-
Y
-
-
X
X
X
X
-
-
X
-
-
-
Y
Numerical
Chemical symbols
EN AW-5087
EN AW-Al Mg4,5MnZr
EN AW-5088
EN AW-Al Mg5Mn0,4
EN AW-5110
EN AW-Al 99,85Mg0,5
-
EN AW-5119
EN AW-Al Mg5(A)
-
EN AW-5119A
EN AW-Al Mg5(B)
-
EN AW-5149
EN AW-Al Mg2Mn0,8(A)
EN AW-5154A
EN AW-Al Mg3,5(A)
Extruded Foil Finstock products
Sheet strip and plate
Drawn products
EN AW-5154B
EN AW-Al Mg3,5Mn0,3
-
-
-
-
X
X
-
-
X
-
-
X
Y
EN AW-5182
EN AW-Al Mg4,5Mn0,4
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-5183
EN AW-Al Mg4,5Mn0,7(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5183A
EN AW-Al Mg4,5Mn0,7(C)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5186
EN AW-Al Mg4Mn0,4
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-5187
EN AW-Al Mg4,5MnZr(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5210
EN AW-Al 99,9Mg0,5
-
-
-
X
-
-
-
-
X
-
X
-
Y
EN AW-5249
EN AW-Al Mg2Mn0,8Zr
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5251
EN AW-Al Mg2Mn0,3
-
-
-
X
X
X
-
-
X
X
-
X
Y
EN AW-5252
EN AW-Al Mg2,5(B)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5283A
EN AW-Al Mg4,5Mn0,7(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN 573-3:2013 (E)
Table A.5 A.5 — Applications and fo rms of p roducts — 5 000 000 series (continued) Allo y desi gnat ion
Forg ing s and forging stock
Wire and drawing stock
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Electrical
Welding
Mechanical
-
-
X
-
-
-
-
-
-
-
-
-
Y
-
-
-
-
-
-
-
-
X
-
-
-
N
-
-
X
-
-
-
-
X
-
X
-
Y
-
X
-
-
-
-
-
-
-
-
-
Y
-
X
-
-
-
-
-
-
-
-
-
Y
-
-
X
-
-
-
-
-
-
-
-
-
Y
-
-
X
X
X
X
-
-
X
-
-
-
Y
Numerical
Chemical symbols
EN AW-5087
EN AW-Al Mg4,5MnZr
EN AW-5088
EN AW-Al Mg5Mn0,4
EN AW-5110
EN AW-Al 99,85Mg0,5
-
EN AW-5119
EN AW-Al Mg5(A)
-
EN AW-5119A
EN AW-Al Mg5(B)
-
EN AW-5149
EN AW-Al Mg2Mn0,8(A)
EN AW-5154A
EN AW-Al Mg3,5(A)
Extruded Foil Finstock products
Sheet strip and plate
Drawn products
EN AW-5154B
EN AW-Al Mg3,5Mn0,3
-
-
-
-
X
X
-
-
X
-
-
X
Y
EN AW-5182
EN AW-Al Mg4,5Mn0,4
-
-
-
-
-
-
-
-
X
X
-
-
Y
EN AW-5183
EN AW-Al Mg4,5Mn0,7(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5183A
EN AW-Al Mg4,5Mn0,7(C)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5186
EN AW-Al Mg4Mn0,4
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-5187
EN AW-Al Mg4,5MnZr(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5210
EN AW-Al 99,9Mg0,5
-
-
-
X
-
-
-
-
X
-
X
-
Y
EN AW-5249
EN AW-Al Mg2Mn0,8Zr
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5251
EN AW-Al Mg2Mn0,3
-
-
-
X
X
X
-
-
X
X
-
X
Y
EN AW-5252
EN AW-Al Mg2,5(B)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5283A
EN AW-Al Mg4,5Mn0,7(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
26
EN 573-3:2013 (E)
Table A.5 A.5 — Applications and fo rms of p roducts — 5 000 000 series (continued) Allo y desi gnat ion Numerical
Chemical symbols
Forgi ngs and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
EN AW-5305
EN AW-Al 99,85Mg1
-
-
-
X
-
-
-
-
X
-
X
-
Y
EN AW-5310
EN AW-Al 99,98Mg0,5
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5352
EN AW-Al Mg2,5(A)
-
-
-
-
-
-
-
-
-
X
-
-
EN AW-5354
EN AW-Al Mg2,5MnZr
-
-
X
-
-
-
-
-
-
-
-
Y Y
EN AW-5356
EN AW-Al Mg5Cr(A)
-
-
X
-
-
-
-
-
-
-
-
-
EN AW-5356A
EN AW-Al Mg5Cr(B)
-
-
X
-
-
-
-
-
-
-
-
-
Y Y
EN AW-5383
EN AW-Al Mg4,5Mn0,9
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-5449
EN AW-Al Mg2Mn0,8(B)
-
-
-
-
-
-
-
-
X
-
-
X
N
EN AW-5454
EN AW-Al Mg3Mn
X
-
-
-
X
X
-
-
X
-
-
X
Y
EN AW-5456
EN AW-Al Mg5Mn1
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-5456A
EN AW-Al Mg5Mn1(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5456B
EN AW-Al Mg5Mn1(B)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5505
EN AW-Al 99,9Mg1
-
-
-
X
-
-
-
-
X
-
X
-
Y
EN AW-5554
EN AW-Al Mg3Mn(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5556A
EN AW-Al Mg5Mn
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5556B
EN AW-Al Mg5Mn (A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5605
EN AW-Al 99,98Mg1
-
-
-
-
-
-
-
-
X
-
-
-
Y Y
EN AW-5654
EN AW-Al Mg3,5Cr
-
-
X
-
-
-
-
-
-
-
-
-
EN AW-5654A
EN AW-Al Mg3,5Cr(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5657
EN AW-Al 99,85Mg1(A)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5754
EN AW-Al Mg3
X
-
X
X
X
X
-
X
X
-
X
X
Y
Y Yes N No X Applicable item
27
EN 573-3:2013 (E)
Table A.5 A.5 — Applications and fo rms of p roducts — 5 000 000 series (continued) Allo y desi gnat ion Numerical
Chemical symbols
Forgi ngs and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
EN AW-5305
EN AW-Al 99,85Mg1
-
-
-
X
-
-
-
-
X
-
X
-
Y
EN AW-5310
EN AW-Al 99,98Mg0,5
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5352
EN AW-Al Mg2,5(A)
-
-
-
-
-
-
-
-
-
X
-
-
EN AW-5354
EN AW-Al Mg2,5MnZr
-
-
X
-
-
-
-
-
-
-
-
Y Y
EN AW-5356
EN AW-Al Mg5Cr(A)
-
-
X
-
-
-
-
-
-
-
-
-
EN AW-5356A
EN AW-Al Mg5Cr(B)
-
-
X
-
-
-
-
-
-
-
-
-
Y Y
EN AW-5383
EN AW-Al Mg4,5Mn0,9
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-5449
EN AW-Al Mg2Mn0,8(B)
-
-
-
-
-
-
-
-
X
-
-
X
N
EN AW-5454
EN AW-Al Mg3Mn
X
-
-
-
X
X
-
-
X
-
-
X
Y
EN AW-5456
EN AW-Al Mg5Mn1
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-5456A
EN AW-Al Mg5Mn1(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5456B
EN AW-Al Mg5Mn1(B)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5505
EN AW-Al 99,9Mg1
-
-
-
X
-
-
-
-
X
-
X
-
Y
EN AW-5554
EN AW-Al Mg3Mn(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5556A
EN AW-Al Mg5Mn
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5556B
EN AW-Al Mg5Mn (A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5605
EN AW-Al 99,98Mg1
-
-
-
-
-
-
-
-
X
-
-
-
Y Y
EN AW-5654
EN AW-Al Mg3,5Cr
-
-
X
-
-
-
-
-
-
-
-
-
EN AW-5654A
EN AW-Al Mg3,5Cr(A)
-
-
X
-
-
-
-
-
-
-
-
-
Y
EN AW-5657
EN AW-Al 99,85Mg1(A)
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-5754
EN AW-Al Mg3
X
-
X
X
X
X
-
X
X
-
X
X
Y
Y Yes N No X Applicable item
27
EN 573-3:2013 (E)
Table A.6 A.6 — Applications and fo rms of p roducts — 6 000 000 series Allo y desi gnat ion
28
Forg ing s and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil
Finstock
Can Sheet strip stock and and plate closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Numerical
Chemical symbols
EN AW-6003
EN AW-Al Mg1Si0,8
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-6005
EN AW-Al SiMg
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6005A
EN AW-Al SiMg(A)
X
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6005B
EN AW-Al SiMg(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6008
EN AW-Al SiMgV
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6011
EN AW-Al Mg0,9Si0,9Cu
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-6012
EN AW-Al MgSiPb
-
-
-
X
X
X
-
-
-
-
-
-
N
EN AW-6012A
EN AW-Al MgSiSn
-
-
-
X
X
X
-
-
-
-
-
-
N
EN AW-6013
EN AW-Al Mg1Si0,8CuMn
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-6014
EN AW-Al Mg0,6Si0,6V
-
-
-
-
-
X
-
-
-
-
-
-
N
EN AW-6015
EN AW-Al Mg1Si0,3Cu
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-6016
EN AW-Al Si1,2Mg0,4
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-6018
EN AW-Al Mg1SiPbMn
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6023
EN AW-Al Si1Sn1MgBi
-
-
-
X
-
X
-
-
-
-
-
-
N
EN AW-6025
EN AW-Al Si1MgMn
-
-
-
-
-
-
-
-
X
-
-
EN AW-6026
EN AW-Al MgSiBi
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6056
EN AW-Al Si1MgCuMn
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6060
EN AW-Al MgSi
X
-
-
X
X
X
-
X
-
-
X
-
Y Y
Y
EN AW-6061
EN AW-Al Mg1SiCu
X
-
-
X
X
X
-
-
X
-
X
-
EN AW-6061A
EN AW-Al Mg1SiCu(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6063
EN AW-Al Mg0,7Si
-
-
-
X
X
X
-
X
X
-
-
-
Y
EN 573-3:2013 (E)
Table A.6 A.6 — Applications and fo rms of p roducts — 6 000 000 series Allo y desi gnat ion
Forg ing s and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil
Finstock
Can Sheet strip stock and and plate closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Numerical
Chemical symbols
EN AW-6003
EN AW-Al Mg1Si0,8
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-6005
EN AW-Al SiMg
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6005A
EN AW-Al SiMg(A)
X
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6005B
EN AW-Al SiMg(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6008
EN AW-Al SiMgV
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6011
EN AW-Al Mg0,9Si0,9Cu
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-6012
EN AW-Al MgSiPb
-
-
-
X
X
X
-
-
-
-
-
-
N
EN AW-6012A
EN AW-Al MgSiSn
-
-
-
X
X
X
-
-
-
-
-
-
N
EN AW-6013
EN AW-Al Mg1Si0,8CuMn
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-6014
EN AW-Al Mg0,6Si0,6V
-
-
-
-
-
X
-
-
-
-
-
-
N
EN AW-6015
EN AW-Al Mg1Si0,3Cu
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-6016
EN AW-Al Si1,2Mg0,4
-
-
-
-
-
-
-
-
X
-
-
-
Y
EN AW-6018
EN AW-Al Mg1SiPbMn
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6023
EN AW-Al Si1Sn1MgBi
-
-
-
X
-
X
-
-
-
-
-
-
N
EN AW-6025
EN AW-Al Si1MgMn
-
-
-
-
-
-
-
-
X
-
-
EN AW-6026
EN AW-Al MgSiBi
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6056
EN AW-Al Si1MgCuMn
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6060
EN AW-Al MgSi
X
-
-
X
X
X
-
X
-
-
X
-
Y
EN AW-6061
EN AW-Al Mg1SiCu
X
-
-
X
X
X
-
-
X
-
X
-
Y
EN AW-6061A
EN AW-Al Mg1SiCu(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6063
EN AW-Al Mg0,7Si
-
-
-
X
X
X
-
X
X
-
-
-
Y
Y
28
EN 573-3:2013 (E)
Table A.6 A.6 — Applications and fo rms of p roducts — 6 000 000 series (continued) Allo y desi gnat ion
Forg ing s and forging stock
Wire and drawing stock Electrical
Welding
Mechanical
Drawn products
Extruded products
Foil Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Numerical
Chemical symbols
EN AW-6063A
EN AW-Al Mg0,7Si(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6064A
EN AW-Al Mg1SiBi
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6065
EN AW-Al Mg1Bi1Si
-
-
-
-
X
X
-
-
-
-
X
-
N
EN AW-6081
EN AW-Al Si0,9MgMn
-
-
-
-
X
X
-
-
X
-
-
EN AW-6082
EN AW-Al Si1MgMn
X
-
-
X
X
X
-
-
X
-
X
X
Y
EN AW-6082A
EN AW-Al Si1MgMn(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6101
EN AW-Al MgSi
-
X
-
-
-
X
-
-
-
-
-
-
N
EN AW-6101A
EN AW-Al MgSi(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
Y
EN AW-6101B
EN AW-Al MgSi(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6106
EN AW-Al MgSiMn
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6110A
EN AW-Al Mg0,9Si0,9MnCu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6181
EN AW-Al Si1Mg0,8
X
-
-
-
-
-
-
-
X
-
-
EN AW-6182
EN AW-Al Si1MgZr
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6201
EN AW-Al Mg0,7Si
-
X
-
-
-
-
-
-
-
-
-
-
N
EN AW-6261
EN AW-Al Mg1SiCuMn
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6262
EN AW-Al Mg1SiPb
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6262A
EN AW-Al Mg1SiSn
-
-
-
-
X
X
-
-
-
-
X
-
N
EN AW-6351
EN AW-Al Si1Mg0,5Mn
-
-
-
-
X
X
-
-
X
-
-
-
Y
EN AW-6351A
EN AW-Al Si1Mg0,5Mn(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
Y
29
EN 573-3:2013 (E)
Table A.6 A.6 — Applications and fo rms of p roducts — 6 000 000 series (continued) Allo y desi gnat ion
Forg ing s and forging stock
Wire and drawing stock Extruded products
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
-
-
Y
Electrical
Welding
Mechanical
Drawn products
-
-
-
-
X
X
-
-
-
-
EN AW-Al Mg1SiBi
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-Al Mg1Bi1Si
-
-
-
-
X
X
-
-
-
-
X
-
N
X
X
-
-
X
-
-
X
X
-
-
X
-
X
X
Y
Foil Finstock
Numerical
Chemical symbols
EN AW-6063A
EN AW-Al Mg0,7Si(A)
EN AW-6064A EN AW-6065 EN AW-6081
EN AW-Al Si0,9MgMn
-
-
-
-
EN AW-6082
EN AW-Al Si1MgMn
X
-
-
X
EN AW-6082A
EN AW-Al Si1MgMn(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6101
EN AW-Al MgSi
-
X
-
-
-
X
-
-
-
-
-
-
N
EN AW-6101A
EN AW-Al MgSi(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6101B
EN AW-Al MgSi(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6106
EN AW-Al MgSiMn
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6110A
EN AW-Al Mg0,9Si0,9MnCu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6181
EN AW-Al Si1Mg0,8
X
-
-
-
-
-
-
-
X
-
-
EN AW-6182
EN AW-Al Si1MgZr
X
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6201
EN AW-Al Mg0,7Si
-
X
-
-
-
-
-
-
-
-
-
-
N
EN AW-6261
EN AW-Al Mg1SiCuMn
-
-
-
-
X
X
-
-
-
-
-
-
Y
EN AW-6262
EN AW-Al Mg1SiPb
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-6262A
EN AW-Al Mg1SiSn
-
-
-
-
X
X
-
-
-
-
X
-
N
EN AW-6351
EN AW-Al Si1Mg0,5Mn
-
-
-
-
X
X
-
-
X
-
-
-
Y
EN AW-6351A
EN AW-Al Si1Mg0,5Mn(A)
-
-
-
-
X
X
-
-
-
-
-
-
Y
Y
Y
29
EN 573-3:2013 (E)
Table A.6 A.6 — Applications and fo rms of p roducts — 6 000 000 series (continued) Allo y desi gnat ion
Wire and drawing stock Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
X
-
-
-
-
-
-
N
Electrical
Welding
Mechanical
Drawn products
-
-
-
-
-
EN AW-Al 99,9MgSi
-
-
-
X
-
-
-
-
-
-
-
-
Y
EN AW-Al Mg0,7Si(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
-
-
-
-
-
-
-
X
-
-
-
-
Y
Numerical
Chemical symbols
EN AW-6360
EN AW-Al Si Mg Mn
EN AW-6401 EN AW-6463 EN AW-6951
EN AW-Al MgSi0,3Cu
Y Yes N No X Applicable item
30
Forg ing s and forging stock
EN 573-3:2013 (E)
Table A.6 A.6 — Applications and fo rms of p roducts — 6 000 000 series (continued) Allo y desi gnat ion
Forg ing s and forging stock
Wire and drawing stock Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
X
-
-
-
-
-
-
N
Electrical
Welding
Mechanical
Drawn products
-
-
-
-
-
EN AW-Al 99,9MgSi
-
-
-
X
-
-
-
-
-
-
-
-
Y
EN AW-Al Mg0,7Si(B)
-
-
-
-
X
X
-
-
-
-
-
-
Y
-
-
-
-
-
-
-
X
-
-
-
-
Y
Numerical
Chemical symbols
EN AW-6360
EN AW-Al Si Mg Mn
EN AW-6401 EN AW-6463 EN AW-6951
EN AW-Al MgSi0,3Cu
Y Yes N No X Applicable item
30
EN 573-3:2013 (E)
Table A.7 A.7 — Applications and fo rms of p roducts — 7 000 000 series Allo y desi gnat ion Chemical symbols
Forgi ngs and forging stock
Wire and drawing stock
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
Electrical
Welding
EN AW-7003
EN AW-Al Zn6Mg0,8Zr
-
-
EN AW-7005
EN AW-Al Zn4,5Mg1,5Mn
-
-
-
-
-
-
-
-
N
-
-
-
-
-
-
EN AW-7009
EN AW-Al Zn5,5MgCuAg
X
N
-
-
-
-
-
-
N
EN AW-7010
EN AW-Al Zn6MgCu
X
-
-
X
-
-
-
N
EN AW-7012 EN AW-7015
X
X
-
-
X
-
-
X
N
-
-
-
-
X
-
-
-
EN AW-7016
N
-
X
X
-
-
-
-
-
-
N
EN AW-7019
-
-
-
-
-
-
X
-
-
-
N
-
-
X
X
X
-
-
X
-
-
-
N
-
-
-
-
-
-
-
X
-
-
-
N
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-Al Zn5Mg1,5Cu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7029
EN AW-Al Zn4,5Mg1,5Cu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7030
EN AW-Al Zn5,5Mg1Cu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7039
EN AW-Al Zn4Mg3
-
-
-
-
-
-
-
-
X
-
-
-
N
Mechanical
Drawn products
Extruded products
-
-
X
X
-
-
X
X
-
-
-
X
X
X
-
-
-
X
EN AW-Al Zn6Mg2Cu
X
-
-
-
EN AW-Al Zn5Mg1,5CuZr
-
-
-
-
EN AW-Al Zn4,5Mg1Cu
-
-
-
EN AW-Al Zn4Mg2
-
-
EN AW-7020
EN AW-Al Zn4,5Mg1
X
EN AW-7021
EN AW-Al Zn5,5Mg1,5
-
EN AW-7022
EN AW-Al Zn5Mg3Cu
EN AW-7026
Numerical
Foil
EN AW-7049A
EN AW-Al Zn8MgCu
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-7050
EN AW-Al Zn6CuMgZr
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-7060
EN AW-Al Zn7CuMg
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7072
EN AW-Al Zn1
-
-
-
-
-
-
-
X
X
-
-
-
N
EN AW-7075
EN AW-Al Zn5,5MgCu
X
-
-
X
X
X
-
-
X
-
-
X
N
EN AW-7108
EN AW-Al Zn5Mg1Zr
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7108A
EN AW-Al Zn5Mg1Zr
-
-
-
-
-
X
-
-
-
-
-
-
N
31
EN 573-3:2013 (E)
Table A.7 A.7 — Applications and fo rms of p roducts — 7 000 000 series Allo y desi gnat ion Chemical symbols
Forgi ngs and forging stock
Electrical
Welding
EN AW-7003
EN AW-Al Zn6Mg0,8Zr
-
-
EN AW-7005
EN AW-Al Zn4,5Mg1,5Mn
-
-
EN AW-7009
EN AW-Al Zn5,5MgCuAg
X
EN AW-7010
EN AW-Al Zn6MgCu
EN AW-7012
EN AW-Al Zn6Mg2Cu
EN AW-7015
EN AW-Al Zn5Mg1,5CuZr
-
-
-
-
-
-
EN AW-7016
EN AW-Al Zn4,5Mg1Cu
-
-
-
-
X
X
Numerical
Wire and drawing stock
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
-
-
-
-
-
-
N
-
-
-
-
-
-
N
-
-
-
-
-
N
-
-
X
-
-
-
N
-
-
X
-
-
X
N
-
-
X
-
-
-
N
-
-
-
-
-
-
N
Mechanical
Drawn products
Extruded products
-
-
X
X
-
-
X
X
-
-
-
X
X
-
X
-
-
-
X
X
X
-
-
-
X
X
Foil
EN AW-7019
EN AW-Al Zn4Mg2
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-7020
EN AW-Al Zn4,5Mg1
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-7021
EN AW-Al Zn5,5Mg1,5
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-7022
EN AW-Al Zn5Mg3Cu
-
-
-
-
X
X
-
-
X
-
-
-
N N
EN AW-7026
EN AW-Al Zn5Mg1,5Cu
-
-
-
-
X
X
-
-
-
-
-
-
EN AW-7029
EN AW-Al Zn4,5Mg1,5Cu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7030
EN AW-Al Zn5,5Mg1Cu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7039
EN AW-Al Zn4Mg3
-
-
-
-
-
-
-
-
X
-
-
-
N
EN AW-7049A
EN AW-Al Zn8MgCu
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-7050
EN AW-Al Zn6CuMgZr
X
-
-
X
X
X
-
-
X
-
-
-
N
EN AW-7060
EN AW-Al Zn7CuMg
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7072
EN AW-Al Zn1
-
-
-
-
-
-
-
X
X
-
-
-
N
EN AW-7075
EN AW-Al Zn5,5MgCu
X
-
-
X
X
X
-
-
X
-
-
X
N
EN AW-7108
EN AW-Al Zn5Mg1Zr
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7108A
EN AW-Al Zn5Mg1Zr
-
-
-
-
-
X
-
-
-
-
-
-
N
31
EN 573-3:2013 (E)
Table A.7 A.7 — Applications and fo rms of p roducts — 7 000 000 series (continued) Allo y desi gnat ion Numerical
Chemical symbols
Forg ing s and forging stock
EN AW-7116
EN AW-Al Zn4,5Mg1Cu0,8
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7129
EN AW-Al Zn4,5Mg1,5Cu(A)
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7149
EN AW-Al Zn8MgCu(A)
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7150
EN AW-Al Zn6CuMgZr(A)
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-7175
EN AW-Al Zn5,5MgCu(B)
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-7178
EN AW-Al Zn7MgCu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7475
EN AW-Al Zn5,5MgCu(A)
-
-
-
-
-
-
-
-
X
-
-
-
N
N No X Applicable item
32
Wire and drawing stock Electrical
Welding
Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Mechanical
Drawn products
Electrowelded tube
Allo ys fo r foodstuff application
EN 573-3:2013 (E)
Table A.7 A.7 — Applications and fo rms of p roducts — 7 000 000 series (continued) Allo y desi gnat ion Numerical
Chemical symbols
Forg ing s and forging stock
Wire and drawing stock
EN AW-7116
EN AW-Al Zn4,5Mg1Cu0,8
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7129
EN AW-Al Zn4,5Mg1,5Cu(A)
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7149
EN AW-Al Zn8MgCu(A)
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7150
EN AW-Al Zn6CuMgZr(A)
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-7175
EN AW-Al Zn5,5MgCu(B)
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-7178
EN AW-Al Zn7MgCu
-
-
-
-
X
X
-
-
-
-
-
-
N
EN AW-7475
EN AW-Al Zn5,5MgCu(A)
-
-
-
-
-
-
-
-
X
-
-
-
N
Electrical
Welding
Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Mechanical
Drawn products
Electrowelded tube
Allo ys fo r foodstuff application
N No X Applicable item
32
EN 573-3:2013 (E)
Table A.8 A.8 — Applications and fo rms of p roducts — 8 000 000 series Allo y desi gnat ion Numerical
Chemical symbols
Forg ing s and forging stock
Wire and drawing stock Electrical
Welding
Drawn Mechanical products
Extruded products
Foil
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
EN AW-8006
EN AW-Al Fe1,5Mn
-
-
-
-
-
-
X
X
X
-
-
-
Y
EN AW-8008
EN AW-Al Fe1Mn0,8
-
-
-
-
-
-
X
-
-
-
-
-
Y
EN AW-8011A
EN AW-Al FeSi(A)
-
-
-
-
-
-
X
X
X
X
-
-
Y
EN AW-8014
EN AW-Al Fe1,5Mn0,4
-
-
-
-
-
-
X
-
-
-
-
-
Y
EN AW-8015
EN AW-Al FeMn0,3
-
-
-
-
-
-
-
X
-
-
-
-
Y
EN AW-8016
EN AW-Al Fe1Mn
-
-
-
-
-
-
-
X
-
-
-
-
Y
EN AW-8018
EN AW-Al FeSiCu
-
-
-
-
-
-
-
-
-
X
-
-
Y
EN AW-8021B
EN AW-Al Fe1,5
-
-
-
-
-
-
X
-
-
-
-
-
Y
EN AW-8030
EN AW-Al FeCu
-
X
-
-
-
-
-
-
-
-
-
-
N
EN AW-8079
EN AW-Al Fe1Si
-
-
-
-
-
-
X
X
X
-
-
-
Y
EN AW-8090
EN AW-Al Li2,5Cu1,5Mg1
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-8111
EN AW-Al FeSi(B)
-
-
-
-
-
-
X
-
X
-
-
-
Y
EN AW-8112
EN AW-Al 95
-
-
-
-
-
-
-
X
X
-
-
-
N
EN AW-8176
EN AW-Al FeSi
-
X
-
-
-
-
-
-
-
-
-
-
N
EN AW-8211
EN AW-Al FeSi(C)
-
-
-
-
-
-
-
-
X
X
-
-
N
Y Yes N No X Applicable item
33
EN 573-3:2013 (E)
Table A.8 A.8 — Applications and fo rms of p roducts — 8 000 000 series Allo y desi gnat ion Numerical
Chemical symbols
EN AW-8006
EN AW-Al Fe1,5Mn
Forg ing s and forging stock -
Wire and drawing stock Electrical
Welding
-
-
Drawn Mechanical products -
-
Extruded products
Foil
-
X
Finstock
Sheet strip and plate
Can stock and closures
Slugs
Electrowelded tube
Allo ys fo r foodstuff application
X
X
-
-
-
Y
EN AW-8008
EN AW-Al Fe1Mn0,8
-
-
-
-
-
-
X
-
-
-
-
-
Y
EN AW-8011A
EN AW-Al FeSi(A)
-
-
-
-
-
-
X
X
X
X
-
-
Y
EN AW-8014
EN AW-Al Fe1,5Mn0,4
-
-
-
-
-
-
X
-
-
-
-
-
Y
EN AW-8015
EN AW-Al FeMn0,3
-
-
-
-
-
-
-
X
-
-
-
-
Y
EN AW-8016
EN AW-Al Fe1Mn
-
-
-
-
-
-
-
X
-
-
-
-
Y
EN AW-8018
EN AW-Al FeSiCu
-
-
-
-
-
-
-
-
-
X
-
-
Y
EN AW-8021B
EN AW-Al Fe1,5
-
-
-
-
-
-
X
-
-
-
-
-
Y
EN AW-8030
EN AW-Al FeCu
-
X
-
-
-
-
-
-
-
-
-
-
N
EN AW-8079
EN AW-Al Fe1Si
-
-
-
-
-
-
X
X
X
-
-
-
Y
EN AW-8090
EN AW-Al Li2,5Cu1,5Mg1
-
-
-
-
X
X
-
-
X
-
-
-
N
EN AW-8111
EN AW-Al FeSi(B)
-
-
-
-
-
-
X
-
X
-
-
-
Y
EN AW-8112
EN AW-Al 95
-
-
-
-
-
-
-
X
X
-
-
-
N
EN AW-8176
EN AW-Al FeSi
-
X
-
-
-
-
-
-
-
-
-
-
N
EN AW-8211
EN AW-Al FeSi(C)
-
-
-
-
-
-
-
-
X
X
-
-
N
Y Yes N No X Applicable item
33
BS EN 573-3:2013
EN 573-3:2013 (E)
An n ex B (normative) Guidelines Guidelines for the introducti on of new wrought aluminium and wrought aluminium alloys in CEN/TC 132 standards B.1 General principles Proposals for the introduction of new alloys in CEN/TC 132 standards or the elimination of existing alloys can be made at any time. If agreed, CEN/TC 132 shall initiate drafts of amendments or of revisions, as appropriate. These drafts shall be process ed following the usual CEN/CENELEC procedures.
B.2 Rules Rules for introduct ion of new new alloys Only those aluminium and aluminium alloys shall be considered for inclusion in CEN/TC 132 standards which are: a)
registered as active alloys in the Registration Record "International Alloy Designations and Chemical Chemical Composition Limits for Wrought Aluminium and Wrought Aluminium Alloys", [1] "Teal Sheets" or published in a regular addendum [2] to the Teal Sheets, for the same numerical designation and the same composition limits for all elements;
b)
currently manufactured and and sold in at least one CEN member country, in commercial quantities and in at least one of the product forms listed in Annex A of this European Standard;
BS EN 573-3:2013
EN 573-3:2013 (E)
An n ex B (normative) Guidelines Guidelines for the introducti on of new wrought aluminium and wrought aluminium alloys in CEN/TC 132 standards B.1 General principles Proposals for the introduction of new alloys in CEN/TC 132 standards or the elimination of existing alloys can be made at any time. If agreed, CEN/TC 132 shall initiate drafts of amendments or of revisions, as appropriate. These drafts shall be process ed following the usual CEN/CENELEC procedures.
B.2 Rules Rules for introduct ion of new new alloys Only those aluminium and aluminium alloys shall be considered for inclusion in CEN/TC 132 standards which are: a)
registered as active alloys in the Registration Record "International Alloy Designations and Chemical Chemical Composition Limits for Wrought Aluminium and Wrought Aluminium Alloys", [1] "Teal Sheets" or published in a regular addendum [2] to the Teal Sheets, for the same numerical designation and the same composition limits for all elements;
b)
currently manufactured and and sold in at least one CEN member country, in commercial quantities and in at least one of the product forms listed in Annex A of this European Standard;
c)
supported by at least one National Standards Organisation.
B.3 Procedure Procedure for introduction of new alloys alloys Each proposal shall contain the following information: a)
designation and composition composition limits as registered in in the Teal sheets;
b)
proposal for a chemical symbol based designation according toEN to EN 573-2; 573-2;
c)
indication of application and form of product for which an introduction is required;
d)
proposal of specific characteristics of new alloys, as appropriate, e.g. mechanical properties.
B.4 Addendum for new alloys alloys for future introduction It has been agreed by CEN/TC 132 to revise EN 573-3 every 573-3 every two years via the UAP procedure.
34
BS EN 573-3:2013
EN 573-3:2013 (E)
Bibliography
[1]
Teal sheets, International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys, The Aluminum Association 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209 USA. Available for download at www.aluminum.org/tealsheets. at www.aluminum.org/tealsheets.
[2]
Addendum to Teal Sheets, International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys , The Aluminum Association 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209 USA. Available for download at www.aluminum.org/tealsheets.
[3]
EN 485-2, 485-2, Aluminium and aluminium alloys — Sheet, strip and plate — Part 2: Mechanical properties
[4]
EN 541, 541, Aluminium and aluminium alloys — Rolled products for cans, closures and lids — Specifications
[5]
EN 546-2, 546-2, Aluminium and aluminium alloys — Foil — Part 2: Mechanical properties
[6]
EN 570, 570, Aluminium and aluminium alloys — Impact extrusion slugs obtained from wrought products — Specification
[7]
EN 573-1, 573-1, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 1: Numerical designation system
[8]
EN 586-2, 586-2, Aluminium and aluminium alloys — Forgings — Part 2: Mechanical properties and additional property requirements
[9]
EN 603-2, 603-2, Aluminium and aluminium alloys — Wrought forging stock — Part 2: Mechanical properties
[10]
EN 683-2, 683-2, Aluminium and aluminium alloys — Finstock — Part 2: Mechanical properties
[11]
EN 754-2, 754-2, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 2: Mechanical properties
[12]
EN 755-2, 755-2, Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 2: Mechanical properties
[13]
EN 851, 851, Aluminium and aluminium alloys — Circle and circle stock for the production of culinary utensils — Specifications
[14]
EN 941, 941, Aluminium and aluminium alloys — Circle and circle stock for general application — Specifications
[15]
EN 1301-2, 1301-2, Aluminium and aluminium alloys — Drawn wire — Part 2: Mechanical properties
[16]
EN 1386, 1386, Aluminium and aluminium alloys — Tread plate — Specifications
[17]
EN 1396, 1396, Aluminium and aluminium alloys — Coil coated sheet and strip for general applications — Specifications
[18]
EN 1592-2, 1592-2, Aluminium and aluminium alloys — HF seam welded tubes — Part 2: Mechanical properties
[19]
EN 1715-2, 1715-2, Aluminium and aluminium alloys — Drawing stock — Part 2: Specific requirements for electrical applications
35
BS EN 573-3:2013
EN 573-3:2013 (E)
[20]
EN 1715-3, 1715-3, Aluminium and aluminium alloys — Drawing stock — Part 3: Specific requirements for mechanical uses (excluding welding)
[21]
EN 1715-4, 1715-4, Aluminium and aluminium alloys — Drawing stock — Part 4: Specific requirements for welding applications
[22]
EN 12392, 12392, Aluminium and aluminium alloys — Wrought products — Special requirements for products intended for the production of pressure equipment
[23]
EN 13957, 13957, Aluminium and aluminium alloys — Extruded round, coiled tube f or general applications — Specification
[24]
EN 13958, 13958, Aluminium and aluminium alloys — Cold drawn, round, coiled tube for general applications — Specification
[25]
EN 13981-1, 13981-1, Aluminium and aluminium alloys — Products for structural railway applications — Technical conditions for inspection and delivery — Part 1: Extruded products
[26]
EN 13981-2, 13981-2, Aluminium and aluminium alloys — Products for structural railway applications — Technical conditions for inspection and delivery — Part 2: Plates and sheets
[27]
EN 13981-4, 13981-4, Aluminium and aluminium alloys — Products for structural railway applications — Technical conditions for inspection and delivery — Part 4: Forgings
[28]
EN 14121, 14121, Aluminium and aluminium alloys — Sheet, strip and plate for electrotechnical applications
[29]
EN 14286, 14286, Aluminium and a nd aluminium alloys — Weldable rolled ro lled products for tanks tank s for the storage and transportation of dangerous goods
36
This page deliberately left blank
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.
About us
Revisions
We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.
Our British Standards and other publications are updated by amendment or revision.
The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.
Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre.
Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop , where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.
Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to bsigroup.com/subscriptions . With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop. It’s available 24/7 and is refreshed daily so you’ll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member .
PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when they’re revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop . With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as they’re available, you can be sure your documentation is current. For further information, email
[email protected].
BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK
We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.
Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization standardizatio n bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording recording or otherwise – without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.
Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders):
[email protected] Email (enquiries):
[email protected] Subscriptions Tel: +44 845 086 9001 Email:
[email protected] Knowledge Centre Tel: +44 20 8996 7004 Email:
[email protected] Copyright & Licensing Tel: +44 20 8996 7070 Email:
[email protected]