2012
AutoCAD Plant 3D System Tools & Variables
Bruce Trevena Cadgroup Australia
[email protected] 10/12/2012
System Variables Contents AutoCAD P&ID System Functions....................................................................... 4
A. 1.
SLINEORTHO ....................................................................................................................... 4
2.
VGRIPS .................................................................................................................................. 4 Plant 3D System Functions .................................................................................. 5
B. 1.
COMPRESSPROJECT ........................................................................................................ 5
2.
PLANTAUDIT ........................................................................................................................ 5
3.
PnPPURGELOCALUSERCACHE ..................................................................................... 6
4.
PLANTSPECUPDATECHECK ........................................................................................... 6
5.
SYNCSTYLESMODE ........................................................................................................... 7 Plant 3D System Variables ................................................................................... 8
C. 6.
PLANTCONNECTIONMARKER ........................................................................................ 8
7.
PLANTCONTENTFOLDER ................................................................................................. 8
8.
PLANTDEFAULTLAYER ..................................................................................................... 8
9.
PLANTDYNTOOLPALETTE ............................................................................................... 9
10.
PLANTGRIPEDITMODE.................................................................................................... 10
11.
PLANTINSULATIONDISPLAY.......................................................................................... 10
12.
PLANTINSULATIONMODE .............................................................................................. 11
13.
PLANTLOCKPOINTOFSUPPORT .................................................................................. 11
14.
PLANTOFFSETCONNECT ............................................................................................... 12
15.
PLANTLOCKFADECTL ..................................................................................................... 12
16.
PLANTMAXBENDANGLE ................................................................................................. 13
17.
PLANTPCFUNICODE ........................................................................................................ 13
18.
PLANTPIPESILHDISPLAY................................................................................................ 14
19.
PLANTPLACEHOLDERDISPLAY .................................................................................... 14
20.
PLANTPROPMISMATCHDISPLAY ................................................................................. 14
21.
PLANTROUTEBEND ......................................................................................................... 15
22.
PLANTSAVEDETAIL .......................................................................................................... 15
23.
PLANTSLOPETHRESHOLDANGLE ............................................................................... 16
24.
PLANTSPECNOTIFY ......................................................................................................... 16
25.
PLANTSPECNOTIFYTIME ............................................................................................... 16
16.
PLANTSPECUPDATECHECK ......................................................................................... 17
17.
PLANTWELCOMEEANBLED ........................................................................................... 17 AutoCAD Plant 3D
2
System Variables 18.
PLANTWELCOMENEWPROJECT .................................................................................. 17
19.
PLANTWELDDISPLAY ...................................................................................................... 18 Additional System Functions .............................................................................. 19
D. 20.
SQL Database Maintenance ............................................................................................. 19
21.
Catalogue Builder ............................................................................................................... 19
AutoCAD Plant 3D
3
System Variables
A. AutoCAD P&ID System Functions 1. SLINEORTHO Sets whether ortho is turned on when sline is activated and whether corner points are implied Type:
Integer
Saved in:
Registry
Initial value:
1
0
Does not turn on ortho when sline is activated. Corner points are not implied
1
Temporarily turns on ortho when sline is activated. Enforces strict orthogonality. Corner points are implied
2. VGRIPS Controls the display of vertex grips. Type:
Integer
Saved in:
Drawing
Initial value:
0 Does not display vertex grips
0 Displays all vertex grips except the first and last points. Set VGRIPS to 1 to alter sline arcs
1 Displays all vertex grips. Set VGRIPS to 2 if you want to enable grips on the first and last points of a line so that you can shorten line segments
2
AutoCAD Plant 3D
4
System Variables
B. Plant 3D System Functions 1. COMPRESSPROJECT Compresses and defragments the cached drawing data that accumulates while project drawings are modified. Access Methods Command entry: compressproject Summary Compresses the drawing data, which is constantly updated as you work on project drawings. To optimize the data cache and improve the program performance, you can do a periodic project compression. For compression to succeed, the project cannot be locked by another designer. If the project is locked, the compression process is halted.
2. PLANTAUDIT Audits and repairs project data and drawing synchronization errors. Access Methods Command entry: plantaudit Summary If a Plant object is not found in the project database, it is erased from the drawing. List of Prompts The following prompts display if synchronization errors are found. Updated cache connection data for part
Erased component not linked to project database
AutoCAD Plant 3D
5
System Variables
3. PnPPURGELOCALUSERCACHE Running this executable purges your local cache. Access Methods Command entry: C:\Program Files\Autodesk\AutoCAD Plant 3D 2013\ PnPPURGELOCALUSERCACHE.exe
Summary Plant 3D uses a local cache to hold drawing and object data. This is done to streamline graphic performance. As the cache file increases in size and reaches a maximum, older contents are deleted. Fatal errors, power outages and illegal procedures such as “SAVEAS” can lead to corruptions in the cache file and it is good practice to purge this local cache from time to time (once a week).
4. PLANTSPECUPDATECHECK In AutoCAD Plant 3D, you can set spec update options to check for changes to a spec and update it when they occur. You are prompted to update the spec and the model when a change to a spec is detected. You can select the parts or properties you want to update and set the time interval between automatic updates. To update a Plant 3D model with a changed spec To set automatic spec updates
PLANTSPECUPDATECHECK PLANTSPECNOTIFY
AutoCAD Plant 3D
6
System Variables
5. SYNCSTYLESMODE Sets how project drawings synchronize with the project database.
Type:
Bitcode
Saved in:
Registry
Initial value: 42 The setting is stored as a bitcode using the sum of the following values: 1
Synchronize P&ID drawings when they are opened.
2
Synchronize open P&ID drawings when the project is modified.
4
Synchronize 3D Model drawings when they are opened.
8
Synchronize open 3D Model drawings when the project is modified.
16
Synchronize Ortho drawings when they are opened.
32
Synchronize open Ortho drawings when the project is modified.
Turn this variable off (0) to improve performance. Set all bits (63) to update P&ID, 3D Model, and Ortho drawings when they are opened, and if the project is modified in Project Setup. The default (42) synchronizes open P&ID, open 3D Model, and Ortho drawings if the project is modified in project setup.
AutoCAD Plant 3D
7
System Variables
C. Plant 3D System Variables 6. PLANTCONNECTIONMARKER Toggles the display of the disconnect marker. Type:
Switch
Saved in:
Registry
Initial value:
0
0
Hides disconnect markers
1
Displays disconnect markers
Turn this variable off (0) to improve performance.
7. PLANTCONTENTFOLDER Displays the shared content catalog folder. (Read-only) Type:
String
Saved in: Registry You can use PLANTMODIFYSHAREDCONTENTFOLDER to set this variable. Note
The Shared Content Folder applies to the installation of AutoCAD Plant 3D. Default: C:\AutoCAD Plant 3D 2013 Content\
8. PLANTDEFAULTLAYER Sets the piping layer to use when using automated layer assignments and the layer cannot be determined. Type:
Integer
Saved in:
Registry Initial value: ”0” Sets the layer to use when the automated layer name cannot be determined. For example, if you are naming layers by line number and change the line number to unassigned. An empty value (setvar "PLANTDEFAULTLAYER" "") will use the current layer.
AutoCAD Plant 3D
8
System Variables
9. PLANTDYNTOOLPALETTE Loads the dynamic pipe spec tool palette from the current spec. Access Methods Command entry: plantdynamictoolpalette Summary You can enable or disable the dynamic pipe spec tool palette.
List of Prompts The Dynamic Pipe Spec Tool Palette is currently . PlantDynamicToolPalette [Enable/Disable]: Enable
Displays the current spec in the tool palette. Disable
Do not use the dynamic tool palette. You can create and customize a static piping component tool palette using the spec viewer. This behavior is compatible with AutoCAD Plant 3D 2011.
AutoCAD Plant 3D
9
System Variables
10. PLANTGRIPEDITMODE Controls whether inline fittings are constrained to move within the current pipe segment or if they move to other connected pipe segments in the network. Command entry: plantgripeditmode Summary You can control whether the inline fittings can be moved only within the current pipe segment or if they can be moved along the connected network to other pipe segments as well. List of Prompts The following prompts are displayed. Grip editing constrains inline fittings to move within [pipeSegment/pipeLine] pipeSegment Constrains movement of inline fittings to a single pipe segment. This mode is compatible with AutoCAD Plant 3D 2010 behavior. pipeLine Allows movement of inline fittings to other pipe segments or to an open area in the drawing.
11. PLANTINSULATIONDISPLAY Controls whether insulation is displayed on AutoCAD Plant 3D piping objects. Type:
Switch
Saved in:
Registry
Initial value:
1
0
Do not display insulation on piping
1
Display the insulation on piping
AutoCAD Plant 3D
10
System Variables
12. PLANTINSULATIONMODE Controls whether insulation is displayed on AutoCAD Plant 3D piping objects. Type:
String
Saved in:
Registry
Initial value:
simplifiedFull
simplifiedFull
All components display insulation.
simplifiedPartial
Display tubing and fittings with insulation. Valves and flanges do not display insulation. Recommend setting when creating orthographic drawings.
13. PLANTLOCKPOINTOFSUPPORT Locks the point-of-support on pipe supports. When on (1), pipe supports that are copied or moved retain their point-of-support. The point-ofsupport is where the pipe support connects to structure. For example, if the support is copied to pipe that is lower in elevation, the support rod of a hanger support increases in height. Not all pipe support types have a point of support. For example, hangers and stanchions have a point-of-support. This variable can also be set with the Lockpointofsupport option of plantpipesupportmove. Type:
Switch
Saved in:
Registry
Initial value:
0
0
Height of pipe support does not change.
1
Maintains the support point when copied or moved.
AutoCAD Plant 3D
11
System Variables
14. PLANTOFFSETCONNECT Controls whether AutoCAD Plant 3D attempts to connect piping when snapping to a pipe connection and using pipe offset while routing. Type:
Switch
Saved in:
Registry
Initial value:
1
0
Do not connect when snapping to a pipe connector
1
Connect when snapping to a pipe connector
15. PLANTLOCKFADECTL Fades locked piping in the 3D model.
Type:
Switch
Saved in:
Registry
Initial value:
0
0
Do not fades locked piping
1
Fades locked piping slightly
Turn this variable off (0) to improve performance.
AutoCAD Plant 3D
12
System Variables
16. PLANTMAXBENDANGLE Specifies whether pipe bends can be used up to 90 or 180 degrees.
Type:
Real
Saved in:
Registry
Initial value:
90
90
Specifies that bends over 90 degrees are not created.
91-179
Specifies that bends larger than 90 can be created.
180
Allows a return bend to be created .
17. PLANTPCFUNICODE Creates Unicode PCF files.
Type:
Switch
Saved in:
Registry
Initial value:
0
0
Creates ASCII compatible PCF files. This format is compatible with AutoCAD Plant 3D 2011 and earlier.
1
Creates Unicode PCF files to fully support multi-byte characters. This setting may not be compatible with other programs.
Multi-byte characters are supported in ACSII PCF files using escape sequences, but this restricts the number of characters supported and can affect formatting.
AutoCAD Plant 3D
13
System Variables
18. PLANTPIPESILHDISPLAY Sets the display of the pipe silhouettes. Type:
Switch
Saved in:
Registry
Initial value:
1
0
Hides pipe silhouettes. If dispsilh is on, plantpipesilhdisplay is ignored and pipe silhouettes display.
1
Displays pipe silhouettes
Turn this variable off (0) to improve performance.
19. PLANTPLACEHOLDERDISPLAY Toggles the display of the Placeholder Part glyph. Type:
Integer
Saved in:
Registry
Initial value:
1
0
On
1
Off
20. PLANTPROPMISMATCHDISPLAY Toggles the display of the property mismatch markers. Type:
Switch
Saved in:
Registry
Initial value:
0
0
Hides property mismatch markers
1
Displays property mismatch markers
Turn this variable off (0) to improve performance.
AutoCAD Plant 3D
14
System Variables
21. PLANTROUTEBEND Creates pipe bends while routing pipe.
Type:
Switch
Saved in:
Registry
Initial value:
0
0
Creates elbow fittings when routing.
1
Creates pipe bends when routing.
This variable can be set with the pipeBEnd option of plantpipeadd.
When plantroutebend is enabled, you set plantmaxbendangle to create bends over 90 degrees.
22. PLANTSAVEDETAIL Sets the detail of the proxy graphics when Plant 3D objects are viewed in AutoCAD or Navisworks without object enablers. Type:
Switch
Saved in:
Registry
Initial value:
1
0
Low detail. Sets proxy graphic detail to use lines. This setting reduces the size of the DWG file when saved.
1
High detail. Sets proxy graphic details to use surfaces. Recommended setting when the drawing is used in Navisworks.
AutoCAD Plant 3D
15
System Variables
23. PLANTSLOPETHRESHOLDANGLE Specifies the angle below which piping is treated as sloped. Command entry: plantslopethresholdangle Summary You can specify the angle that identifies what piping is treated as sloped and what is not. Type: Integer Saved in:
Registry
Initial value:
5
1-45
On. Piping over this value is considered sloped. Piping over this value is considered angled. The default angle is 5 degrees.
0
Off. No piping is sloped.
24. PLANTSPECNOTIFY Checks for spec file updates when the drawing loads, and on a time interval. Type:
Integer
Saved in:
Registry
Initial value:
1
1
On. Checks for spec file updates when the drawing loads, and on the time interval specified by the plantspecnotifytime system variable
0
Off. Does not check for spec file updates
25. PLANTSPECNOTIFYTIME Sets the time interval that spec files are checked for updates. Type:
Integer
Saved in:
Registry
Initial value:
2
0
Checks for spec file updates only when the drawing loads
1-4
Sets the time interval (in hours) that spec files are checked for updates. The first check is made when the drawing loads
AutoCAD Plant 3D
16
System Variables
16. PLANTSPECUPDATECHECK Checks for changes made to spec files that are in use in a drawing. Access Methods Command entry: plantspecupdatecheck Summary You can check for changes to a pipe spec that is used in a 3D model. If changes are discovered, you can update the model. NoteThis command can run automatically by setting
the plantspecnotify and plantspecnotifytime system variables. See Also Update a Spec in a Plant 3D Model
17. PLANTWELCOMEEANBLED Displays the Welcome Screen Setting to 0 will prevent the opening of Plant 3D Welcome Dialogue, a address the issue of Plant 3D freezing on the Welcome Screen. Type:
Integer
Saved in:
Registry
Initial value:
0
1
On; You can create a project from the welcome screen
0
Off
18. PLANTWELCOMENEWPROJECT Displays the New Project button on the welcome screen. Type:
Integer
Saved in:
Registry
Initial value:
0
1
On; You can create a project from the welcome screen
0
Off
AutoCAD Plant 3D
17
System Variables
19. PLANTWELDDISPLAY Toggles the display of connection markers. Type:
Switch
Saved in:
Registry
Initial value:
0
0
Hides connection markers such as weld and glue markers
1
Displays connection markers
Turn this variable off (0) to improve performance.
AutoCAD Plant 3D
18
System Variables
D. Additional System Tools
20. SQL Database Maintenance PnPProjectMaintenance.exe
21. Catalogue Builder AutoCADPlant3DCatalogBuilder.exe
*Reference: AutoCAD Plant 3D 2013, Autodesk Inc.
AutoCAD Plant 3D
19
