Version 3.2.1
Data Structure Reference Guide
AT321_DSR_E1
Atoll 3.2.1 Data Structure Reference Guide Release: AT321_DSR_E1 © 1997-2014 Forsk. All Rights Reserved. Published by: Forsk 7 rue des Briquetiers 31700 Blagnac, France Tel: +33 562 747 210 Fax: +33 562 747 211 The software described in this document is provided under a licence agreement. The software may only be used or copied under the terms and conditions of the licence agreement. No part of the contents of this document may be reproduced or transmitted in any form or by any means without written permission from the publisher. The products or brand names mentioned in this document are trademarks or registered trademarks of their respective registering parties. The publisher has taken care in the preparation of this document, but makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages in connection with or arising out of the use of the information contained herein.
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
AT321_DSR_E1
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 About Forsk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 About Atoll Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Contacting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1 1.1 1.1.1 1.1.2 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 1.39 1.40 1.41 1.42 1.43 1.44 1.45 1.46 1.47 1.48 1.49
GSM GPRS EDGE Data Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Data Structure Changes Between Atoll 3.1 and 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Added Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 AfpModels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Antennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 BSICDomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 BSICGroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 BTSEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 CellTypes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 ChannelModels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 CodecEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 CodecModeAdaptations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 CodecModes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 CodecQualityTables Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 CoordSys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 CustomFields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 EGPRSCodingSchemes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 EGPRSDimensioningModel Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 EGPRSEnvironmentDefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 EGPRSEquipments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 EGPRSMobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 EGPRSQuality Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 EGPRSServiceQuality Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 EGPRSServices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 EGPRSServicesUsage Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 EGPRSTerminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 EGPRSTrafficEnvironments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 EGPRSUserProfiles Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 FeederEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 FrequencyBands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 FrequencyDomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 FrequencyGroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 HSNDomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 HSNGroups Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 InterNetChProtect Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Layers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Neighbours Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 NeighboursConstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 NeighboursConstraintsExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 NeighboursExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 PropagationModels Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 QualityIndicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Receivers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 RepeaterEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Repeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SecondaryAntennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SeparationRules Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Separations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Sites Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 SitesLists Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
1
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
1.50 1.51 1.52 1.53 1.54 1.55 1.56 1.57 1.58 1.59 1.60 1.61 1.62 1.63
2 2.1 2.1.1 2.1.2 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24 2.25 2.26 2.27 2.28 2.29 2.30 2.31 2.32 2.33 2.34 2.35 2.36 2.37 2.38 2.39 2.40 2.41 2.42 2.43 2.44 2.45 2.46 2.47 2.48
2
© Forsk 2014
SitesListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 TMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 TplTransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Transmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 TRGConfigurations Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 TRGs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 TRXEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 TRXs Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 TRXTypes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 TSConfigurationNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 TSConfigurations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 TxsLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 TxsListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
UMTS HSPA Data Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Data Structure Changes Between Atoll 3.1 to 3.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Added Tables and Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Antennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 BTSEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 CDMACells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 CdmaEqptsHSUPARssUse Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 CDMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 CDMAEquipmentsCEsUse Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 CoordSys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 CustomFields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 FeederEquipments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 FrequencyBands Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 HSDPABearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 HSDPABearerSelectTables Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 HSDPAQualityTables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 HSPAMIMOConfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 HSUPABearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 HSUPABearerSelection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 HSUPAQualityTables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 HSUPAUECategories Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 InterfReductionFactors Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 InterNetChProtect Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 MUGTables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Neighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 NeighboursConstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 NeighboursConstraintsExt Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 NeighboursExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 PropagationModels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 QualityIndicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 R99Bearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Receivers Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 RepeaterEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Repeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 ScramblingCodesDomains Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ScramblingCodesGroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Schedulers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 SecondaryAntennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Separations Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ServiceQualityTables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Sites Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 SitesLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 SitesListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 TMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 TplTransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Transmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 TxsLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 TxsListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 UECategories Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
AT321_DSR_E1
2.49 2.50 2.51 2.52 2.53 2.54 2.55 2.56 2.57 2.58
3 3.1 3.1.1 3.1.2 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 3.36 3.37 3.38 3.39 3.40 3.41 3.42 3.43 3.44 3.45 3.46 3.47 3.48 3.49 3.50 3.51 3.52
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
UERxEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 UMTSEnvironmentDefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 UMTSMobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 UMTSServices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 UMTSServicesQuality Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 UMTSServicesUsage Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 UMTSTerminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 UMTSTraficEnvironments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 UMTSUserProfiles Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
CDMA2000 Data Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Data Structure Changes Between Atoll 3.1 and 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Added Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Antennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 BTSEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 CarriersType Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 CDMACells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 CDMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 CDMAEquipmentsCEsUse Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 CoordSys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 CustomFields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 DLBearersSelection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 DLDORABearers Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 DORABearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 DORABearersProba Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 DORATerminalT2PRatios Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 FeederEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 FrequencyBands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 InterfReductionFactors Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 InterNetChProtect Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Neighbours Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 NeighboursConstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 NeighboursConstraintsExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 NeighboursExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 PnCodesDomains Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 PnCodesGroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 PropagationModels Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 QualityIndicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Receivers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 RepeaterEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Repeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 SecondaryAntennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Separations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 ServiceQualityTables Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Sites Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 SitesLists Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 SitesListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 TMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 TplTransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Transmitters Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 TxsLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 TxsListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 UERxEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 ULBearersSelection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 UMTSEnvironmentDefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 UMTSMobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 UMTSServices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 UMTSServicesQuality Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 UMTSServicesUsage Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 UMTSTerminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 UMTSTraficEnvironments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 UMTSUserProfiles Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
3
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
4 4.1 4.1.1 4.1.2 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 4.18 4.19 4.20 4.21 4.22 4.23 4.24 4.25 4.26 4.27 4.28 4.29 4.30 4.31 4.32 4.33 4.34 4.35 4.36 4.37 4.38 4.39 4.40 4.41 4.42 4.43 4.44 4.45 4.46 4.47 4.48 4.49 4.50 4.51
5 5.1 5.1.1 5.1.1.1 5.1.1.2 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.1.7
4
© Forsk 2014
LTE Data Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Data Structure Changes Between Atoll 3.1 and 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Added Tables and Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BTSEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CoordSys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CustomFields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FeederEquipments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FrequencyBands Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . InterNetChProtect Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lcchdivgains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lframeconfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . llayers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lpcidomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lpcigroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MUGTables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Neighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NeighboursConstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NeighboursConstraintsExt Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NeighboursExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PropagationModels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . QualityIndicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receivers Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RepeaterEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Schedulers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SecondaryAntennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sites Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SitesLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SitesListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SmartAntennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SmartAntennasModels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GBearerQualityCurves Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GBearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GBearersRequiredCI Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GCells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GEnvironmentDefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GMimoConfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GMobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GServices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GServicesUsage Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GTerminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GTraficEnvironments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GUECategories Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4GUserProfiles Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TplTransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxsLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxsListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115 115 118 118 119 119 120 121 122 122 122 123 123 124 124 124 124 125 125 125 126 127 127 127 127 128 129 129 129 130 130 130 130 131 131 131 131 134 134 134 134 135 136 136 137 137 138 138 138 141 142 142 142
3GPP Multi-RAT Data Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Tables Common to All Technologies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Structure Changes Between Atoll 3.1 and 3.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Added Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . antennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . btsequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . coordsys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . customfields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . environmentdefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . feederequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
145 145 145 145 146 146 146 146 146 146
AT321_DSR_E1
5.1.8 5.1.9 5.1.10 5.1.11 5.1.12 5.1.13 5.1.14 5.1.15 5.1.16 5.1.17 5.1.18 5.1.19 5.1.20 5.1.21 5.1.22 5.1.23 5.1.24 5.2 5.2.1 5.2.1.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 5.2.9 5.2.10 5.2.11 5.2.12 5.2.13 5.2.14 5.2.15 5.2.16 5.2.17 5.2.18 5.2.19 5.2.20 5.2.21 5.2.22 5.2.23 5.2.24 5.2.25 5.2.26 5.2.27 5.2.28 5.2.29 5.2.30 5.2.31 5.2.32 5.2.33 5.2.34 5.2.35 5.2.36 5.2.37 5.2.38 5.2.39 5.2.40 5.2.41 5.2.42 5.2.43 5.2.44 5.2.45 5.2.46 5.3 5.3.1
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
internetchprotect Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 mobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 propagationmodels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 receivers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 repeaterequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 services Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 servicesusage Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 sites Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 siteslists Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 siteslistsnames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 smartantennasmodels Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 terminals Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 tmaequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 trafficenvs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 userprofiles Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 GSM-specific Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Changes in Data Structure From 3.1 to 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Added Tables and Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 gafpmodels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gbsicdomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gbsicgroups Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcelltypes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcodecequipments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcodecmodeadapts Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcodecmodes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcodecqualtables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcodingschemes Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcsequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 gcsquality Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 gdimensmodel Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 gfreqdomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 gfreqgroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 gfrequencybands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 ghsndomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 ghsngroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 glayers Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 glneighbours Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 glneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 gneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gneighconstraints Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gneighext Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gneighextconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gqualityindicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 grepeaters Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gsecondaryantennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gseparationrules Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gseparations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gservicequality Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gservices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gterminals Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 gtpltransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtrgconfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtrgs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtrxequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtrxs Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtrxtypes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtsconfignames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtsconfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtxslists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 gtxslistsnames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 guneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 guneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 UMTS-specific Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Changes in Data Structure From 3.1 to 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
5
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
5.3.1.1 5.3.1.2 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.3.8 5.3.9 5.3.10 5.3.11 5.3.12 5.3.13 5.3.14 5.3.15 5.3.16 5.3.17 5.3.18 5.3.19 5.3.20 5.3.21 5.3.22 5.3.23 5.3.24 5.3.25 5.3.26 5.3.27 5.3.28 5.3.29 5.3.30 5.3.31 5.3.32 5.3.33 5.3.34 5.3.35 5.3.36 5.3.37 5.3.38 5.3.39 5.3.40 5.3.41 5.3.42 5.3.43 5.4 5.4.1 5.4.1.1 5.4.2 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.4.8 5.4.9 5.4.10 5.4.11 5.4.12 5.4.13 5.4.14 5.4.15 5.4.16 5.4.17 5.4.18 5.4.19 5.4.20 5.4.21
6
© Forsk 2014
Added Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ucells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uceuse Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ufrequencybands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ugneighbours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ugneighconstraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsdpabearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsdpabearerselect Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsdpaqualtables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhspamimoconfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsupabearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsupabearerselect Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsupaqualtables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsuparessuse Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uhsupauecategories Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uinterfreducfactors Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ulneighbours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ulneighconstraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . umobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . umugtables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uneighext Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uneighextconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . upscdomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . upscforbidpairs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . upscgroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uqualityindicators Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ur99bearers Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . urepeaters Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uschedulers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . usecondaryantennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uservicequaltables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uservices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uservicesquality Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uterminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . utpltransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . utransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . utxslists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . utxslistsnames Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uuecategories Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . uuerxequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LTE-specific Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changes in Data Structure From 3.1 to 3.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Added Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lbearerqualitycurves Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lbearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lbearersrequiredci Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lcells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lcchdivgains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lframeconfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lfrequencybands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lgneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lgneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . llayers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lmimoconfigs Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lmugtables Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighext Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighextconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lpcidomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lpcigroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lqualityindicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
156 157 158 158 158 158 158 158 158 159 159 159 159 159 159 159 159 159 159 159 160 160 160 160 160 160 160 160 160 160 160 160 161 161 161 161 161 161 161 161 161 161 161 161 161 162 162 164 164 164 164 164 164 164 164 165 165 165 165 165 165 165 165 165 166 166 166
AT321_DSR_E1
5.4.22 5.4.23 5.4.24 5.4.25 5.4.26 5.4.27 5.4.28 5.4.29 5.4.30 5.4.31 5.4.32 5.4.33 5.4.34
6 6.1 6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 6.1.6 6.1.7 6.1.8 6.1.9 6.1.10 6.1.11 6.1.12 6.1.13 6.1.14 6.1.15 6.1.16 6.1.17 6.1.18 6.1.19 6.1.20 6.1.21 6.1.22 6.1.23 6.2 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 6.2.7 6.2.8 6.2.9 6.2.10 6.2.11 6.2.12 6.2.13 6.2.14 6.2.15 6.2.16 6.2.17 6.2.18 6.2.19 6.2.20 6.2.21 6.2.22 6.2.23 6.2.24 6.2.25 6.2.26
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
lrepeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 lschedulers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 lsecondaryantennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 lservices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 lsmartantennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 lterminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 ltpltransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 ltransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 ltxslists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 ltxslistsnames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 luecategories Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 luneighbours Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 luneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
3GPP2 Multi-RAT Data Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 Tables Common to All Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 antennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 btsequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 coordsys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 customfields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 environmentdefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 feederequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 internetchprotect Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 mobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 propagationmodels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 receivers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 repeaterequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 services Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 servicesusage Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 sites Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 siteslists Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 siteslistsnames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 smartantennasmodels Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 terminals Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 tmaequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 trafficenvs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 userprofiles Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 CDMA2000-specific Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 ccarrierstype Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 ccells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cceuse Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cdlbearerselect Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cdldorabearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cdorabearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cdorabearersproba Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cdoratermt2pratios Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cequipments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cfrequencybands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 cinterfreducfactors Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 clneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 clneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cmobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cneighconstraints Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cneighext Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cneighextconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cpnodomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cpnoforbidpairs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cpnogroups Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cqualityindicators Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 crepeaters Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 csecondaryantennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 cservicequaltables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 cservices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
7
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
6.2.27 6.2.28 6.2.29 6.2.30 6.2.31 6.2.32 6.2.33 6.2.34 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.3.7 6.3.8 6.3.9 6.3.10 6.3.11 6.3.12 6.3.13 6.3.14 6.3.15 6.3.16 6.3.17 6.3.18 6.3.19 6.3.20 6.3.21 6.3.22 6.3.23 6.3.24 6.3.25 6.3.26 6.3.27 6.3.28 6.3.29 6.3.30 6.3.31
7 7.1 7.1.1 7.1.2 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19 7.20 7.21 7.22
8
© Forsk 2014
cservicesquality Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cterminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ctpltransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ctransmitters Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ctxslists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ctxslistsnames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cuerxequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . culbearerselect Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LTE-specific Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lbearerqualitycurves Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lbearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lbearersrequiredci Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lcells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lcchdivgains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lcneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lcneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lequipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lframeconfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lfrequencybands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . llayers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lmimoconfigs Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lmugtables Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighext Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lneighextconstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lpcidomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lpcigroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lqualityindicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lrepeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lschedulers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lsecondaryantennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lservices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lsmartantennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lterminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ltpltransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ltransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ltxslists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ltxslistsnames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . luecategories Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
177 177 177 177 177 177 177 177 177 177 177 177 178 178 178 178 178 178 178 178 178 179 179 179 179 179 179 179 179 179 179 179 179 179 179 180 180 180 180 180
TD-SCDMA Data Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Data Structure Changes Between Atoll 3.1 and 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Added Tables and Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AntennasLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AntennasListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BTSEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CDMACells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CDMACellsTS Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CDMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CDMAEquipmentsCEsUse Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CodesRelativityClusters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CoordSys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CustomFields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FeederEquipments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FrequencyBands Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSDPABearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSDPABearerSelectTables Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSUPABearers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSUPABearerSelection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSUPAUECategories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . InterfReductionFactors Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . InterNetChProtect Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Neighbours Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
184 184 184 184 185 185 185 186 187 188 188 189 189 190 191 191 191 192 192 192 193 193 193 194
AT321_DSR_E1
7.23 7.24 7.25 7.26 7.27 7.28 7.29 7.30 7.31 7.32 7.33 7.34 7.35 7.36 7.37 7.38 7.39 7.40 7.41 7.42 7.43 7.44 7.45 7.46 7.47 7.48 7.49 7.50 7.51 7.52 7.53 7.54 7.55 7.56 7.57 7.58 7.59 7.60
8 8.1 8.1.1 8.1.2 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 8.10 8.11 8.12 8.13 8.14 8.15 8.16 8.17 8.18 8.19 8.20 8.21 8.22 8.23 8.24
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
NeighboursConstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 NeighboursConstraintsExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 NeighboursExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 PropagationModels Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 QualityIndicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 R99Bearers Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Receivers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 RepeaterEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 Repeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 SACIGainCDF Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 ScramblingCodesDomains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 ScramblingCodesGroups Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 SecondaryAntennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 Separations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 ServiceQualityTables Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 ServiceRUsUse Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Sites Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 SitesLists Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 SitesListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 SmartAntennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 SmartAntennasModels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 TMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 TplTransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Transmitters Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 TxsLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 TxsListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 UECategories Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 UERxEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 UMTSEnvironmentDefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 UMTSMobility Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 UMTSServices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 UMTSServicesQuality Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 UMTSServicesUsage Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 UMTSTerminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 UMTSTraficEnvironments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 UMTSUserProfiles Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 Units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
WiMAX and Wi-Fi Data Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 Data Structure Changes Between Atoll 3.1 and 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Added Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 Antennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 BTSEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 CoordSys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 CustomFields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 FeederEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 FrameConfigurations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 FrequencyBands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 InterNetChProtect Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 MUGTables Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Neighbours Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 NeighboursConstraints Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 NeighboursConstraintsExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 NeighboursExt Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 PermutationZones Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 PropagationModels Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 QualityIndicators Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Receivers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 RepeaterEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Repeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Schedulers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 SecondaryAntennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Sites Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
9
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
8.25 8.26 8.27 8.28 8.29 8.30 8.31 8.32 8.33 8.34 8.35 8.36 8.37 8.38 8.39 8.40 8.41 8.42 8.43 8.44 8.45 8.46 8.47 8.48 8.49 8.50 8.51
9 9.1 9.1.1 9.1.2 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13 9.14 9.15 9.16 9.17 9.18 9.19 9.20 9.21 9.22 9.23 9.24 9.25 9.26 9.27 9.28 9.29 9.30 9.31 9.32 9.33 9.34 9.35
10
© Forsk 2014
SitesLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SitesListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SmartAntennas Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SmartAntennasModels Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TMAEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TplTransmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmitters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxsLists Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxsListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WBearerQualityCurves Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WBearers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WBearersRequiredCI Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WCCHDivGains Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WCells Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WEnvironmentDefs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WEquipments Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WLayers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WMimoConfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WMobility Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WPIDomains Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WPIGroups Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WServices Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WServicesUsage Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WTerminals Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WTraficEnvironments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WUserProfiles Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
231 231 231 231 231 232 234 235 236 236 236 236 237 237 237 239 239 239 240 240 240 241 241 242 243 243 243
Microwave Links Data Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 Data Structure Changes Between Atoll 3.1 and 3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Added Tables and Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deleted Tables and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BHNodes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BHSegments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BHSegmentsMedia Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CoordSys Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CustomFields Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWAntennas Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWBands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWBranchingConfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWCapacities Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWCompatibilities Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWCompatibilitiesGuides Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWDefaultsCurves Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWEPO Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWEPOLinkClass Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWEquipments Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWFamilies Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWFamilyBands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWFamilyBrConfigs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWFamilyChSpacings Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWFamilyModulations Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWFrequencies Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWGuides Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWHubs Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWIrfs Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWLinks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWLinkTypes Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWManufacturers Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWMediumTypes Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWModulations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWMultiHops Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWMultiHopsLinks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWOperatingModes Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWOTLinks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWPMP Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
245 245 249 249 249 250 250 251 252 253 253 253 254 254 254 255 255 256 258 258 258 258 259 259 259 260 260 260 264 264 264 265 265 265 265 266 266
AT321_DSR_E1
9.36 9.37 9.38 9.39 9.40 9.41 9.42 9.43 9.44 9.45
10 10.1 10.1.1 10.1.2 10.2 10.3 10.4
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
MWPorts Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 MWRepeaters Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 MWSubbands Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 MWTplLinks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Networks Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 PropagationModels Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 Sites Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 SitesLists Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 SitesListsNames Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 Units Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
Radio Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273 XML Import/Export Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 Index.xml File Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 XML File Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 RF 2D Antenna Pattern Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Import Format of 3D Antenna Pattern Text Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Microwave 2D Antenna Pattern Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
11
Atoll 3.2.1 Data Structure Reference Guide Table of Contents
12
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Introduction
AT321_DSR_E1
Introduction Atoll is a 64-bit multi-technology wireless network design and optimisation platform that supports wireless operators throughout the network lifecycle, from initial design to densification and optimisation. Atoll’s integration and automation features help operators smoothly automate planning and optimisation processes through flexible scripting and SOA-based mechanisms. Atoll supports a wide range of implementation scenarios, from standalone to enterprise-wide server-based configurations. Atoll Microwave is based on the leading Atoll platform which includes a high performance GIS and advanced data and user management features. Atoll Microwave can share the site database with Atoll radio planning and optimisation modules allowing easy data consistency management across the operator organisation. This Data Structure Reference Guide provides reference material covering the Atoll database structure and file format for database administrators and advanced users.
About Forsk Forsk is an independent company providing radio planning and optimisation software solutions to the wireless industry since 1987. In 1997, Forsk released the first version of Atoll, its flagship radio planning software. Since then, Atoll has evolved to become a comprehensive radio planning and optimisation platform and, with more than 5700 installed licenses worldwide, has reached the leading position on the global market. Atoll combines engineering and automation functions that enable operators to smoothly and gradually implement SON processes within their organisation. Today, Forsk is a global supplier with over 300 customers in 100 countries and strategic partnerships with major players in the industry. Forsk distributes and supports Atoll directly from offices and technical support centres in France, USA, and China as well as through a worldwide network of distributors and partners. Since the first release of Atoll, Forsk has been known for its capability to deliver tailored and turn-key radio planning and optimisation environments based on Atoll. To help operators streamline their radio planning and optimisation processes, Forsk provides a complete range of implementation services, including integration with existing IT infrastructure, automation, as well as data migration, installation, and training services.
Getting Help The online help system that is installed with Atoll is designed to give you quick access to the information you need to use the product effectively. It contains the same material as the Atoll 3.2.1 User Manual. You can use the online help to search for specific keywords or to print individual topics or chapters. To print help topics or chapters: 1. In Atoll, click Help > Online Help. 2. In the Contents tab, expand the table of contents. 3. Right-click the section or topic that you want to print and click Print. The Print Topics dialog box opens. 4. In the Print Topics dialog box, select what you want to print: • •
If you want to print a single topic, select Print the selected topic. If you want to print an entire section, including all topics and sections in that section, select Print the selected heading and all subtopics.
5. Click OK.
About Atoll Documentation The following PDF manuals are available for Atoll and Atoll Microwave and can be downloaded from the Forsk web site at: http://www.forsk.com/support. • • • • • •
Atoll 3.2.1 Administrator Manual Atoll 3.2.1 User Manual Atoll 3.2.1 Technical Reference Guide Atoll 3.2.1 Data Structure Reference Guide Atoll 3.2.1 Model Calibration Guide Atoll 3.2.1 Task Automation Guide
13
Atoll 3.2.1 Data Structure Reference Guide Introduction
© Forsk 2014 Forsk
To read PDF manuals, you can download Adobe Reader from the Adobe web site at: http://get.adobe.com/reader/ For hardcopy manuals, contact to your Forsk representative.
Contacting Technical Support Forsk provides global technical support for its products and services. To contact Forsk support, visit the Forsk Support web site at: http://www.forsk.com/support. Alternatively, depending on your geographic location, contact one of the following support teams: •
Forsk Head Office For regions other than North and Central America and China, contact the Forsk Head Office support team: • • •
Tel.: +33 562 747 225 Fax: +33 562 747 211 Email:
[email protected]
Opening Hours: Monday to Friday 9.00 am to 6.00 pm (GMT +1:00) Except on the following bank holidays in 2013: January 1st, April 1st, May 1st, May 8th, May 9th, May 20th, August 15th, November 1st, November 11th, December 25th •
Forsk US For North and Central America, contact the Forsk US support team: • • •
Tel.: 1-888-GO-ATOLL (1-888-462-8655) Fax: 1-312-674-4822 Email:
[email protected]
Opening Hours: Monday to Friday 8.00 am to 8.00 pm (Eastern Standard Time) •
Forsk China For China, contact the Forsk China support team: • • •
14
Tel: +86 20 8557 0016 Fax: +86 20 8553 8285 Email:
[email protected]
AT321_DSR_E1
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
1 GSM GPRS EDGE Data Structure The Atoll GSM/GPRS/EDGE module provides comprehensive and accurate modelling of voice and data services, including full support of HCS and frequency hopping. This section describes the GSM GPRS EDGE data structure used in Atoll. Figure 1.1 on page 16, Figure 1.2 on page 17, and Figure 1.3 on page 18 depict the structure of the GSM GPRS EDGE database. The following subsections list the tables in the GSM GPRS EDGE database template.
15
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Figure 1.1: GSM GPRS EDGE Template - 1
16
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Figure 1.2: GSM GPRS EDGE Template - 2
17
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Figure 1.3: GSM GPRS EDGE Template - 3
1.1 Data Structure Changes Between Atoll 3.1 and 3.2 1.1.1 Added Tables and Fields Antennas Table Field
Type
Description
Attributes
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
CustomFields Table
18
Field
Type
Description
Attributes
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
EGPRSServices Table Field
Type
Description
Attributes
MIN_THROUGHPUT_UL
Float
Uplink minimum user throughput requested for the service
Null column allowed: Yes Default value: 15
PRIORITY
Short
Service priority (0: lowest)
Null column allowed: Yes Default value: 0
EGPRSServicesUsage Table Field
Type
Description
Attributes
UL_VOLUME
Float
Volume transferred on the uplink during a session (for packet switched services)
Null column allowed: Yes Default value:
EGPRSTerminals Table Field
Type
Description
Attributes
PMIN
Float
Minimum receiver power on traffic channels not to exceed
Null column allowed: Yes Default value: -40
Field
Type
Description
Attributes
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
Sites Table
TplTransmitters Table Field
Type
Description
Attributes
NOISE_FIGURE
Float
Total noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value:
REUSE_DISTANCE
Float
Typical reuse distance for assignments
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Default value:
Transmitters Table Field
Type
Description
Attributes
NOISE_FIGURE
Float
Total noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
REUSE_DISTANCE
Float
Typical reuse distance for assignments
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Default value: 0
Field
Type
Description
Attributes
VAMOS_RATIO
Float
TRGs Table
Percentage of VAMOS (Voice services over Adaptive Multi-user channels Null column allowed: Yes on One Slot) traffic in the subcell. Default value: 0
19
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
1.1.2 Deleted Tables and Fields Sites Table •
SUPPORT_NATURE
1.2 AfpModels Table For AFP models. Field
Type
Description
Attributes
DATA
Binary
Model specific parameters
Null column allowed: Yes Default value:
DESCRIPTION
Text (255)
User defined
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the AFP model
Null column allowed: No Default value:
SIGNATURE
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
TYPE
Text (50)
ProgID of the model
Null column allowed: No Default value:
1.3 Antennas Table For antennas. Field
Type
Description
Attributes
Beamwidth
Float
Antenna beamwidth
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about antenna
Null column allowed: Yes Default value:
CONSTRUCTOR
Text (50)
Antenna manufacturer name
Null column allowed: Yes Default value:
DIAGRAM
Binary
Antenna horizontal and vertical patterns
Null column allowed: Yes Default value:
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
ELECTRICAL_TILT
Float
Antenna electrical tilt (for information)
Null column allowed: Yes Default value:
FMax
Double
Maximum operating frequency of the antennas Unit: MHz
Null column allowed: Yes Default value:
FMin
Double
Minimum operating frequency of the antenna Unit: MHz
Null column allowed: Yes Default value:
GAIN
Float
Antenna isotropic gain Unit: dBi
Null column allowed: No Default value: 0
NAME
Text (50)
Name of antenna
Null column allowed: No Default value:
PHYSICAL_ANTENNA
Text (50)
Physical antenna name
Null column allowed: Yes Default value:
The format of the binary field, DIAGRAM, is described in "RF 2D Antenna Pattern Format" on page 275.
20
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
1.4 BSICDomains Table For names of BSIC domains. Field
Type
Description
Attributes
NAME
Text (50)
Name of the domain
Null column allowed: No Default value:
1.5 BSICGroups Table For BSIC groups belonging to BSIC domains. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Called grouping scheme. Set of resource groups.
Null column allowed: No Default value:
EXCLUDED
Text (225)
List of BSICs to be excluded from the series defined by FIRST, LAST and STEP (separated with commas)
Null column allowed: Yes Default value:
EXTRA
Text (225)
BSIC to be added. It is forbidden for EXTRA and EXLUDED to have common numbers
Null column allowed: Yes Default value:
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
Unique key. Name of a resource group
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
The FIRST and LAST fields of this table are of type Integer in the template (.mdb) and in a database (if connected to one). But these fields are of type Text when accessed or retrieved from an add-in.
1.6 BTSEquipments Table For BTS equipment. Field
Type
Description
Attributes
CONFIG_DL_LOSSES
Float
Downlink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
CONFIG_UL_LOSSES
Float
Uplink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Base Station Equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Base Station
Null column allowed: Yes Default value: 0
RHO_FACTOR
Short
Rho factor (not used)
Null column allowed: Yes Default value: 100
1.7 CellTypes Table For cell types.
21
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
NAME
Text (50)
Defines the list of TRXs of the station and associated parameters.
Null column allowed: No Default value:
1.8 ChannelModels Table For channel models. Field
Type
Description
Attributes
NAME
Text (50)
Name of the channel model
Null column allowed: No Default value:
TX_DIV_GAIN
Float
Gain applied for subcells using TX diversity
Null column allowed: No Default value: 0
1.9 CodecEquipments Table For codec configurations. Field
Type
Description
Attributes
IDEAL_LINK_ADAPTATION
Boolean
Automatic mode selection providing the best quality
Null column allowed: No Default value: True
IDEAL_QI_NAME
Text (20)
Reference quality indicator name used for ideal link adaptation
Null column allowed: Yes Default value:
NAME
Text (50)
Name of Codec equipment
Null column allowed: No Default value:
REFERENCE_NOISE
Float
Receiver reference noise
Null column allowed: No Default value: -113
1.10 CodecModeAdaptations Table For codec mode selection. Field
Type
Description
Attributes
CODEC_EQT
Text (50)
Codec equipment name
Null column allowed: No Default value:
CODEC_MODE
Text (50)
Codec mode
Null column allowed: No Default value:
FREQUENCY_BAND
Text (20)
Frequency Band (empty = all bands)
Null column allowed: Yes Default value:
HOPPING
Short
Frequency hopping 1=NH; 2= ideal FH; empty = all hopping modes
Null column allowed: Yes Default value:
MAL_LENGTH
Integer
MAL length
Null column allowed: Yes Default value:
MIN_CIR
Float
C/(I+N) quality threshold for selecting this mode when there is no ideal link adaptation
Null column allowed: Yes Default value: 0
MOBILITY
Text (50)
Mobility (empty = all mobilities)
Null column allowed: Yes Default value:
1.11 CodecModes Table For codec types and modes.
22
Field
Type
Description
Attributes
_8PSK_MODULATION
Boolean
Modulation is 8PSK
Null column allowed: No Default value: False
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
CODEC_TYPE
Text (50)
Name of codec type
Null column allowed: No Default value:
HR
Boolean
Half rate support
Null column allowed: No Default value: False
MAX_RATE
Float
Maximum supported rate for this mode (kbps)
Null column allowed: No Default value: 0
NAME
Text (50)
Name of the codec mode
Null column allowed: No Default value:
SELECTION_PRIORITY
Short
Priority value used to select the best possible mode
Null column allowed: No Default value: 0
1.12 CodecQualityTables Table For codec performance graphs. Field
Type
Description
Attributes
C_I_TABLE
Memo
QI = f(C/I) table
Null column allowed: Yes Default value:
C_N_TABLE
Memo
QI = f(C/N) table
Null column allowed: Yes Default value:
CODEC_EQT
Text (50)
Codec equipment name
Null column allowed: No Default value:
CODEC_MODE
Text (50)
Codec mode
Null column allowed: No Default value:
FREQUENCY_BAND
Text (20)
Frequency Band (empty = all bands)
Null column allowed: Yes Default value:
HOPPING
Short
Frequency hopping 1=NH; 2= ideal FH; empty = all hopping modes
Null column allowed: Yes Default value:
MAL_LENGTH
Integer
MAL length
Null column allowed: Yes Default value:
MOBILITY
Text (50)
Mobility (empty = all mobilities)
Null column allowed: Yes Default value:
QI_NAME
Text (20)
Quality indicator name
Null column allowed: No Default value:
1.13 CoordSys Table For the projection coordinate system and the database’s internal coordinate system ( this is the display coordinate system used when creating a database). Field
Type
Description
Attributes
CODE
Integer
Identification number of the coordinate system (the code of userdefined coordinate systems is an integer higher than 32768)
Null column allowed: No Default value: 0
DATUM_CODE
Double
DATUM_ROTX
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTY
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTZ
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_SCALE
Double
Parts per million (ppm)
Null column allowed: Yes Default value: 0
DATUM_SHIFTX
Double
Meters
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
23
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DATUM_SHIFTY
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTZ
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_CODE
Integer
ELLIPS_RMAJOR
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_RMINOR
Double
Meters
Null column allowed: Yes Default value: 0
NAME
Text (50)
Coordinate system name
Null column allowed: No Default value:
PROJ_ANGLE
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_FALSE_EASTING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FALSE_NORTHING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FIRST_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LATITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LONGITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_METHOD
Short
UTM, Undefined, NoProjection, Lambert1SP, Lambert2SP, Mercator, CassiniSoldner, TransMercator, TransMercatorSO, ObliqueStereographic, NewZealandMapGrid, HotineOM, LabordeOM, SwissObliqueCylindical
Null column allowed: Yes Default value: 0
PROJ_SCALE_FACTOR
Double
PROJ_SECOND_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_ZONE_NUMBER
Integer
Used with UTM
Null column allowed: Yes Default value: 0
Null column allowed: No Default value: 0
Null column allowed: Yes Default value: 0
1.14 CustomFields Table For defining user-defined fields added to tables, default values for any field (including user-defined fields), and choice lists, captions, and group names for user-defined fields.
24
Field
Type
Description
Attributes
CAPTION
Text (50)
Caption of the field (displayed instead of the name)
Null column allowed: Yes Default value:
CHOICE_LIST
Memo
Choice list for the field
Null column allowed: Yes Default value:
CHOICE_TYPE
Integer
0: Choice List is optional; 1: Choice List is mandatory
Null column allowed: Yes Default value: 0
COLUMN_NAME
Text (50)
Second part of the unique key. Field name
Null column allowed: No Default value:
DEFAULT_VALUE
Text (50)
Default value for the field
Null column allowed: Yes Default value:
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
GROUP_NAME
Text (50)
Name of the group to which that field belongs
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
TABLE_NAME
Text (50)
First part of the unique key. Table name
Null column allowed: No Default value:
These are some general recommendations that you should follow when handling databases. General • • • •
In order to use Atoll with Oracle, you must create Oracle users and schema with names in uppercase. Create backups of the database before upgrading. It is recommended to define a rule for making backups of the database at regular intervals. Do not skip a major Atoll version. For example, if you are currently using Atoll 2.7.xV6.7, you should first upgrade the database to Atoll 2.8.xV6.9 before upgrading to Atoll 3.1.xV7.1. Upgrading your database will be simpler if you do not skip a major version. If you skip or have skipped an intermediate major version, you must upgrade your database twice in order to make it compatible with the new version.
Tables and Fields • •
Table and field names are case sensitive. Table and field names should be not more than 20 characters long. Oracle databases allow a maximum length of 30 characters for field and table names. However, for use in Atoll, you must not create tables and fields with names longer than 20 characters. This is because Atoll adds some characters to the table and field names for certain operations: creating associated triggers, creating project databases, etc. Limiting the length of table and field names to 20 characters will help avoid database connection and consistency problems.
• • • • • •
• •
Table and field names should only use alphanumeric characters (A-Z, a-z, 0-9) and underscores (_). Table and field names must not start with a numeric character (0-9). Table and field names must not contain an SQL or RDBMS-specific keyword, such as ORDER, DATE, etc. Table and field names must not contain spaces or special characters, such as periods (.), exclamation marks (!), colons (:), semi-colons (;), interrogation marks (?), parentheses (()), brackets ({}), square brackets ([]), etc. Boolean fields, system or user-defined, should always have default values assigned. The CustomFields table enables you to define default values, choice lists, and read/write access for any field in any table in Atoll, including user-defined fields that you add to the Atoll tables. The values defined in this table have priority over the internal predefined default values. If you define floating point default values, make sure that all the users have the same decimal separator. If you wish to add custom fields in the Atoll document, you should first add the field in the database, and then update your Atoll document from the database. When setting up your database for the first time, try to anticipate user requirements in terms of custom fields in Atoll tables. Some requirements of the different user groups can be satisfied if a few general-purpose user-defined fields are added in Atoll tables when setting up the database. For example, if you add three user-defined fields (one of type integer, float, and text (limited size)) to the Sites and Transmitters tables, users will be able to use these for sorting, filtering, grouping, or other purposes. This approach can help the database function a long time before users require the addition of other custom fields.
• •
•
To improve performance, if your projects allow it, reduce the size of the fields corresponding to the sites and transmitters’ names. To improve performance, unless absolutely necessary, do not add user-defined fields of Text type. Rather, use numeric field types, which allow sorting and other functions. If you must add Text fields, allocate them the appropriate size that would suffice. For example, a 255-character long Text type field would, for the most part, occupy disk space for no purpose. To improve performance, you should avoid adding custom fields to the neighbour management tables.
1.15 EGPRSCodingSchemes Table For GPRS, EGPRS, and EGPRS2 coding schemes. Field
Type
Description
Attributes
CS_NUMBER
Short
Coding scheme number
Null column allowed: No Default value: 1
DATA_CODING
Short
Type of FEC coding (0: Convolutional, 1: Turbo)
Null column allowed: No Default value: 0
MAX_THROUGHPUT
Float
Maximum rate obtained when there is no data transmission error Unit: kbps
Null column allowed: No Default value: 1
25
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MODULATION
Short
Modulation (0: GMSK,1: 8-PSK, 2: QPSK,3: 16QAM, 4: 32QAM)
Null column allowed: No Default value: 0
NAME
Text (50)
Name of the coding scheme
Null column allowed: No Default value:
TECHNOLOGY
Text (15)
Technology ("GPRS", "GPRS/EDGE", "EGPRS2")
Null column allowed: No Default value: ’GPRS’
1.16 EGPRSDimensioningModel Table For network dimensioning models. Field
Type
Description
Attributes
MAX_CHANNELS
Text (4)
Maximum number of TRXs that can be allocated
Null column allowed: No Default value: ’16’
MAX_TRXS_TO_ADD_FOR_P ACKET
Integer
Maximum allowed number of TRXs to add in order to reach required quality for packet switched services
Null column allowed: Yes Default value: 100
MIN_DEDICATED_PDCH
Integer
Minimum dedicated timeslots number for packet switched traffic
Null column allowed: No Default value: 0
NAME
Text (50)
Service Name
Null column allowed: No Default value:
PDCH_BLOCKING_PROBA_KP I
Boolean
Blocking probability KPI
Null column allowed: No Default value: False
PDCH_DELAY_KPI
Boolean
Service delay KPI
Null column allowed: No Default value: False
PDCH_THROUGHPUT_MIN_K PI
Boolean
Minimum throughput KPI
Null column allowed: No Default value: True
QUEUING_MODEL
Text (50)
Queuing model: Erlang B , Erlang C
Null column allowed: Yes Default value: ’Erlang B’
1.17 EGPRSEnvironmentDefs Table For traffic environment types. Field
Type
Description
Attributes
DENSITY
Float
Number of subscribers per km2
Null column allowed: Yes Default value: 0
ENVIRONMENT
Text (50)
Environment name
Null column allowed: No Default value:
MOBILITY
Text (50)
Type of mobility
Null column allowed: No Default value:
USER_PROFILE
Text (50)
User profile
Null column allowed: No Default value:
1.18 EGPRSEquipments Table For GPRS, EGPRS, and EGPRS2 configurations.
26
Field
Type
Description
Attributes
NAME
Text (50)
Equipment name
Null column allowed: No Default value:
REFERENCE_NOISE
Float
Reference noise of the equipment which has been used to produce the Null column allowed: Yes curves Default value: -113
TECHNOLOGY
Text (15)
GSM, GPRS or GPRS/EDGE. To allocate traffic to compatible transmitter Null column allowed: Yes mobile pair. Default value: GPRS
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
1.19 EGPRSMobility Table For mobility types. Field
Type
Description
Attributes
NAME
Text (50)
Name of mobility type
Null column allowed: No Default value:
SPEED
Float
Average speed (km/h)
Null column allowed: No Default value:
1.20 EGPRSQuality Table For GPRS, EGPRS, and EGPRS2 performance graphs. Field
Type
Description
Attributes
C_THRESHOLD
Float
Minimum power (C) required at the receiver in order for a coding scheme to be used
Null column allowed: Yes Default value: 1
C_THROUGHPUTS
Memo
Set of values used to generate throughput=f(C) graph
Null column allowed: Yes Default value:
COVERI_THRESHOLD
Float
Minimum carrier to interference ratio (C/I) required at the receiver in order for a coding scheme to be used
Null column allowed: Yes Default value: 1
COVERI_THROUGHPUTS
Memo
Set of values used to generate the throughput=f(C/I) graph
Null column allowed: Yes Default value: ’0’
CS_NAME
Text (10)
Coding scheme name
Null column allowed: Yes Default value:
EQUIPMENT
Text (50)
Type of equipment
Null column allowed: No Default value:
FREQUENCY_BAND
Text (20)
Frequency Band (empty = all bands)
Null column allowed: Yes Default value:
HOPPING
Short
MAL_LENGTH
Integer
MAL length
Null column allowed: Yes Default value:
MOBILITY
Text (50)
Mobility (empty = all mobilities)
Null column allowed: Yes Default value:
Hopping mode corresponding to the curves ( 1=NH; 2= ideal FH; empty = Null column allowed: Yes all hopping modes) Default value:
1.21 EGPRSServiceQuality Table For graphs used for the packet-switched traffic dimensioning. Field
Type
Description
Attributes
AVAIL_CONNECTIONS
Float
Number of available connections
Null column allowed: Yes Default value: 1
DIMENSIONING_MODEL
Text (50)
Name of the dimensioning model
Null column allowed: No Default value:
LOAD_BLOCKING_PROBA
Memo
Set of values used to generate the chart Blocking=f(Load)
Null column allowed: Yes Default value: ’1’
LOAD_DELAY
Memo
Set of values used to generate the chart Delay=f(Load)
Null column allowed: Yes Default value: ’1’
LOAD_RF
Memo
Set of values used to generate the chart throughput reduction factor=f(Load)
Null column allowed: Yes Default value: ’1’
1.22 EGPRSServices Table For services.
27
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DL_ACTIVITY
Float
Activity factor for voice services on the downlink
Null column allowed: Yes Default value: 1
DL_MBR
Float
DL Maximum Throughput
Null column allowed: Yes Default value: 0
MAX_BLOCKING_RATE
Float
MAX_DELAY
Float
Maximum delay allowed for the service
Null column allowed: Yes Default value: 1
MAX_TS_SUPPORT
Integer
Maximum number of timeslots supported by the service
Null column allowed: Yes Default value: 4
MIN_THROUGHPUT
Float
Minimum user throughput requested for the service
Null column allowed: Yes Default value: 15
MIN_THROUGHPUT_RATIO
Float
Dimensioning target of the % of surface where minimum throughput is reached
Null column allowed: Yes Default value: 95
MIN_THROUGHPUT_UL
Float
Minimum user throughput requested for the service
Null column allowed: Yes Default value: 15
NAME
Text (50)
Service Name
Null column allowed: No Default value: ’1’
PRIORITY
Short
Service priority (0: lowest)
Null column allowed: Yes Default value: 0
REQ_AVERAGE_UL_RATE
Float
Requested Average Uplink Rate (kbps)
Null column allowed: Yes Default value:
TH_OFFSET
Float
Offset which should be added to the scale factor
Null column allowed: Yes Default value: 0
TH_SCALE_FACTOR
Float
Percentage of end user throughput compared to MAC throughput
Null column allowed: Yes Default value: 95
TYPE
Short
Type of service (0: circuit; 1: packet; 2: circuit over packet)
Null column allowed: No Default value: 0
UL_ACTIVITY
Float
Activity factor for voice services on the uplink
Null column allowed: Yes Default value: 1
UL_MBR
Float
UL Maximum Throughput
Null column allowed: Yes Default value: 0
Maximum probability that a packet is blocked (delayed), GoS for circuit Null column allowed: Yes switched services Default value: 2
1.23 EGPRSServicesUsage Table For user profile parameters.
28
Field
Type
Description
Attributes
CALL_DURATION
Float
Average duration of a call (for circuit switched services)
Null column allowed: Yes Default value:
CALL_NUMBER
Float
Average number of calls per hour for circuit switched services or average number of sessions per hour for packet switched services
Null column allowed: Yes Default value: 0
DL_VOLUME
Float
Volume transferred on the downlink during a session (for packet switched services)
Null column allowed: Yes Default value:
SERVICE
Text (50)
Service that the subscriber can request
Null column allowed: No Default value:
TERMINAL
Text (50)
Type of terminal used by the subscriber for the service
Null column allowed: No Default value:
UL_VOLUME
Float
Volume transferred on the uplink during a session (for packet switched services)
Null column allowed: Yes Default value:
USER_PROFILE
Text (50)
User profile name
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
1.24 EGPRSTerminals Table For terminal types. Field
Type
Description
Attributes
CODEC_EQUIPMENT
Text (50)
Associated Codec Equipment (for voice services)
Null column allowed: Yes Default value:
DL_AVAIL_CARRIERS
Short
Number of simultaneous carriers
Null column allowed: Yes Default value: 1
DL_AVAIL_TIME_SLOT
Float
Number of timeslots the mobile terminal can multiplex in downlink
Null column allowed: Yes Default value: 1
DTX
Boolean
DTX capability of terminal
Null column allowed: No Default value: True
EGPRS_EQUIPMENT
Text (50)
Associated GPRS/EDGE equipment (for PS services)
Null column allowed: Yes Default value:
MAX_CS
Short
Highest coding scheme (CS) available for GPRS
Null column allowed: Yes Default value: 4
MAX_MCS
Short
Highest coding scheme (MCS) available for EDGE
Null column allowed: Yes Default value: 12
NAME
Text (50)
Terminal name
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of the terminal
Null column allowed: Yes Default value: 8
PMAX
Float
Max power that can be used in UL (for UL calculations)
Null column allowed: Yes Default value: 33
PMIN
Float
Minimum receiver power on traffic channels not to exceed
Null column allowed: Yes Default value: -40
PRIMARY_BAND
Text (50)
Frequency band the mobile terminal is compatible with
Null column allowed: No Default value:
SAIC
Boolean
Terminal capability for Single Antenna Interference Cancellation (for future use)
Null column allowed: No Default value: False
SECONDARY_BAND
Text (50)
Frequency band the mobile terminal is compatible with (for dual-band mobile terminals)
Null column allowed: Yes Default value:
TECHNOLOGY
Text (15)
Technology supported by the mobile terminal
Null column allowed: Yes Default value:
1.25 EGPRSTrafficEnvironments Table For traffic environment clutter weighting. Field
Type
Description
Attributes
CLUTTER_WEIGHTS
Binary
Internal binary format describing weights assigned to each clutter class
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the created environment
Null column allowed: No Default value:
1.26 EGPRSUserProfiles Table For names of user profiles. Field
Type
Description
Attributes
NAME
Text (50)
Name of the created user profile
Null column allowed: No Default value:
29
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
1.27 FeederEquipments Table For feeders. Field
Type
Description
Attributes
CONNECTOR_LOSSES_DL
Float
Feeder connector losses in downlink
Null column allowed: Yes Default value: 0
CONNECTOR_LOSSES_UL
Float
Feeder connector losses in uplink
Null column allowed: Yes Default value: 0
LOSS_PER_METER
Float
Feeder loss per meter
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Feeder
Null column allowed: No Default value:
1.28 FrequencyBands Table For frequency bands. Field
Type
Description
Attributes
CHANNEL_WIDTH
Double
Width of each physical channel composing the frequency band Unit: kHz
Null column allowed: No Default value: 1
EXCLUDED_CHANNELS
Text (255)
Physical channels you do not want to allocate
Null column allowed: Yes Default value:
FIRST_CHANNEL
Integer
Number of the first physical channel available in the network
Null column allowed: No Default value: 0
FREQUENCY
Double
Frequency of the downlink carrier Unit: MHz
Null column allowed: No Default value: 1000
LAST_CHANNEL
Integer
Number of the last physical channel available in the network
Null column allowed: No Default value: 0
MAX_CHANNEL_NUM
Integer
Extended Channel Offset (used for band E-GSM)
Null column allowed: Yes Default value:
MULTIPLEX_FACTOR
Integer
Number of logical channels composing a physical channel
Null column allowed: No Default value: 1
NAME
Text (20)
Name of the frequency band
Null column allowed: No Default value:
1.29 FrequencyDomains Table For frequency bands belonging to frequency domains. Field
Type
Description
Attributes
FREQUENCY_BAND_NAME
Text (50)
Name of the frequency band on which domain is based
Null column allowed: No Default value:
NAME
Text (50)
Name of domain
Null column allowed: No Default value:
1.30 FrequencyGroups Table For frequency groups belonging to frequency domains.
30
Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Called grouping scheme. Set of resource groups.
Null column allowed: No Default value:
EXCLUDED
Text (255)
List of frequencies to be excluded from the series defined by FIRST, LAST Null column allowed: Yes and STEP (separated with commas) Default value:
EXTRA
Text (225)
Frequencies to be added. It is forbidden for EXTRA and EXLUDED to have Null column allowed: Yes common numbers Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
Unique key. Name of a Resource Group
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
1.31 HSNDomains Table For names of HSN domains. Field
Type
Description
Attributes
NAME
Text (50)
Name of HSN (Hopping Sequence Number) domain.
Null column allowed: No Default value:
1.32 HSNGroups Table For HSN groups belonging to HSN domains. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Called grouping scheme. Set of resource groups.
Null column allowed: No Default value:
EXCLUDED
Text (225)
List of HSNs to be excluded from the series defined by FIRST, LAST and STEP (separated with commas)
Null column allowed: Yes Default value:
EXTRA
Text (225)
HSNs to be added. It is forbidden for EXTRA and EXLUDED to have common numbers
Null column allowed: Yes Default value:
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
Unique key. name of a Resource Group
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
1.33 InterNetChProtect Table For inter-network interference reduction factor graphs. Field
Type
Description
Attributes
ICP
Memo
Inter-network channel protection = f( MHz)
Null column allowed: Yes Default value:
ITF_BW
Double
Interfering bandwidth (kHz)
Null column allowed: No Default value: 0
ITF_TECHNO
Text (50)
Interfering technology
Null column allowed: No Default value:
V_BW
Double
Victim bandwidth (kHz)
Null column allowed: No Default value: 0
31
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
1.34 Layers Table For HCS layers. Field
Type
Description
Attributes
MAX_SPEED
Float
Threshold speed for a mobile considered eligible to reside on a layer
Null column allowed: Yes Default value: 300
MIN_PRIORITY_POWER
Float
Minimum power value for the HCS layer
Null column allowed: Yes Default value: -130
NAME
Text (50)
Name of the hierarchical cell structure layer
Null column allowed: No Default value:
PRIORITY
Short
Priority of the layer (largest value has the highest priority)
Null column allowed: No Default value: 1
1.35 Neighbours Table For intra-technology neighbour relations. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
1.36 NeighboursConstraints Table For intra-technology neighbour allocation constraints. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
1.37 NeighboursConstraintsExt Table For inter-technology neighbour allocation constraints. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
32
Text (50) Second part of the unique key. List of neighbours from another project.
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
1.38 NeighboursExt Table For inter-technology neighbour relations. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50) Second part of the unique key. List of neighbours from another project
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
1.39 Networks Table For network-level parameters. Field
Type
Description
Attributes
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value:
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -130
NAME
Text (50)
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value: ‘GSM’
TECHNOLOGY
Text (10)
Name of the technology
Null column allowed: No Default value: ‘TDMA’
THERMAL_NOISE
Float
Thermal noise
Null column allowed: Yes Default value: -121
Null column allowed: No Default value:
1.40 PropagationModels Table For propagation models. Field
Type
Description
Attributes
Data
Binary
Model specific parameters
Null column allowed: Yes Default value:
Description
Text (255)
User defined
Null column allowed: Yes Default value:
33
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
Name
Text (50)
Name of the propagation model
Null column allowed: No Default value:
Signature
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
Type
Text (50)
ProgID of the model
Null column allowed: No Default value:
1.41 QualityIndicators Table For quality indicators (BER, BLER, etc.). Field
Type
Description
Attributes
CS_QI
Boolean
Flag which indicates if this indicator is used in CS services
Null column allowed: No Default value: True
MEAS_PARAM
Short
Name of the measured figure used for this QI determination Choice list: 1=C; 2=CIR;
Null column allowed: Yes Default value: 1
NAME
Text (20)
Name of the managed quality indicator
Null column allowed: No Default value:
PS_QI
Boolean
Flag which indicates if this indicator is used for PS services
Null column allowed: No Default value: True
USE_INTERPOLATION
Boolean
Flag which indicates if this QI must be interpolated or not
Null column allowed: No Default value: True
1.42 Receivers Table For receiver parameters. Field
Type
Description
Attributes
ADJ_CHANNEL_PROT
Float
Protection against interfering signals from adjacent channels.
Null column allowed: No Default value: 18
ANTENNA
Text (50)
Receiver antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the receiver
Null column allowed: No Default value: 1.5
LOSS
Float
Losses due to receiver radio equipment (up and downlink)
Null column allowed: No Default value: 0
NAME
Text (50)
Receiver name
Null column allowed: No Default value:
1.43 RepeaterEquipments Table For repeater equipment.
34
Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
MANUFACTURER
Text (50)
Manufacturer of the repeater equipment
Null column allowed: Yes Default value:
MAX_AMPLIFIER_GAIN
Float
Maximum gain of the amplifier (dB)
Null column allowed: Yes Default value: 90
MAX_OUTPUT_DL
Float
Maximum downlink output power (dBm)
Null column allowed: Yes Default value: 30
MAX_OUTPUT_UL
Float
Maximum uplink output power (dBm)
Null column allowed: Yes Default value: 12
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MIN_AMPLIFIER_GAIN
Float
Minimum gain of the amplifier (dB)
Null column allowed: Yes Default value: 50
NAME
Text (50)
Name of the repeater equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Repeater noise Figure (dB)
Null column allowed: Yes Default value: 5
STEP_AMPLIFIER_GAIN
Float
Step of amplifier gain (dB)
Null column allowed: Yes Default value: 1
TIME_DELAY
Float
Time delay in the equipment (microseconds)
Null column allowed: Yes Default value: 5
1.44 Repeaters Table For repeaters. Field
Type
Description
Attributes
AMPLIFIER_GAIN
Float
Gain of the amplifier
Null column allowed: Yes Default value: 80
AZIMUT
Float
Azimuth of the donor side antenna
Null column allowed: Yes Default value: 0
DONOR_CELLID
Text (50)
Name of the donor transmitter
Null column allowed: No Default value:
DONOR_LINK_LOSS
Float
Loss (dB) between donor and donor side of the repeater
Null column allowed: Yes Default value: 0
DONOR_LINK_TYPE
Short
1- Off air 2- Microwave 3- Fibre
Null column allowed: No Default value: 1
DONOR_PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction between donor and repeater
Null column allowed: Yes Default value:
DOWNTILT
Float
Downtilt of the donor side antenna
Null column allowed: Yes Default value: 0
EIRP
Float
EIRP of the repeater
Null column allowed: Yes Default value: 0
EQUIPMENT_NAME
Text (50)
If no equipment, the repeater is a passive component
Null column allowed: Yes Default value:
FEEDER_NAME
Text (50)
Name of the donor side feeder
Null column allowed: Yes Default value:
FEEDERLENGTH
Float
Length of donor side feeder
Null column allowed: Yes Default value: 0
HEIGHT
Float
Height of the donor side antenna
Null column allowed: Yes Default value: 25
REC_ANTENNA
Text (50)
Name of the donor side antenna
Null column allowed: Yes Default value:
REC_FEEDERLENGTH_UL
Float
Length of donor side uplink feeder
Null column allowed: Yes Default value: 0
TX_ID
Text (50)
Name of the repeater (and of the transmitter used for coverage)
Null column allowed: No Default value:
• •
Repeater properties are saved in two tables: the donor-side parameters are in the Repeaters table and the coverage-side parameters in the Transmitters table. The repeater EIRP taken into account in calculations is stored in the Repeaters table (the EIRP column of the Transmitters table is not used).
1.45 SecondaryAntennas Table For additional antennas.
35
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna installed on the transmitter
Null column allowed: No Default value:
AZIMUT
Float
Second part of the unique key. Azimuth of the antenna
Null column allowed: No Default value: 0
PERCENT_POWER
Float
Percentage of power dedicated to the secondary antenna
Null column allowed: No Default value: 0
REDT
Float
Remote electrical tilt for secondary antenna
Null column allowed: Yes Default value: 0
TILT
Float
Mechanical downtilt of the secondary antenna
Null column allowed: No Default value: 0
TX_ID
Text (50)
First part of the unique key. Transmitter name
Null column allowed: No Default value:
1.46 SeparationRules Table For default separation constraints between each type of subcells. Field
Type
Description
Attributes
DEFAULT_MIN_SEP
Short
Minimum separation requirement
Null column allowed: No Default value: 1
RELATION_TYPE
Short
Type of the relation : 1=Co-Subcell; 2=Co-Cell; 3=Co-Site; 4=Neighbour
Null column allowed: No Default value: 1
TRX_TYPE
Text (15)
Type of TRX or All
Null column allowed: No Default value: ’All’
TRX_TYPE_OTHER
Text (15)
Type of TRX or All
Null column allowed: No Default value: ’All’
1.47 Separations Table For separation constraints between types of subcells. Field
Type
Description
Attributes
MIN_SEP
Integer
Minimum separation requirement.
Null column allowed: No Default value: 1
TRX_TYPE
Text (15)
First transmitter subcell or All
Null column allowed: No Default value: “All”
TRX_TYPE_OTHER
Text (15)
Second transmitter subcell or All
Null column allowed: No Default value: “All”
TX_ID
Text (50)
First transmitter name in a symmetric relation.
Null column allowed: No Default value:
TX_ID_OTHER
Text (50)
Second transmitter name in a symmetric relation.
Null column allowed: No Default value:
1.48 Sites Table For sites.
36
Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude Unit: m
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information on the site
Null column allowed: Yes Default value:
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
1.49 SitesLists Table For sites belonging to site lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list
Null column allowed: No Default value:
SITE_NAME
Text (50)
Second part of the unique key. Name of the site
Null column allowed: No Default value:
1.50 SitesListsNames Table For names of site lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
1.51 TMAEquipments Table For tower-mounted amplifiers. Field
Type
Description
Attributes
DL_LOSSES
Float
Downlink losses of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Tower Mounted Amplifier
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
UL_GAIN
Float
Uplink gain of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
1.52 TplTransmitters Table For station templates. Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value:
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the first antenna
Null column allowed: No Default value:
BSIC_DOMAIN
Text (50)
A text field pointing to ResourceGroups.NAME. It limits the BSIC domain Null column allowed: Yes of the site. Default value:
37
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define each transmitter calculation area Unit: m
Null column allowed: Yes Default value:
CALC_RADIUS2
Integer
Extended calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value:
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CELL_RESELECT_OFFSET
Integer
Cell reselection offset
Null column allowed: Yes Default value:
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value:
CELL_TYPE
Text (50)
CODEC_EQUIPMENT
Text (50)
Associated Codec equipment (for voice services)
Null column allowed: Yes Default value:
CODING_SCHEME_NUMBER
Short
The number of coding schemes supported by the GPRS/EDGE transmitters
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
EGPRS_EQUIPMENT
Text (255)
Name of the equipment assigned to the GPRS/EDGE station
Null column allowed: Yes Default value:
EIRP
Float
Transmitter’s effective isotropic radiated power
Null column allowed: Yes Default value:
ENABLE_EGPRS
Boolean
'Yes' enables you to consider the transmitter as a GPRS/EDGE station
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value:
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value:
FN_OFFSET
Integer
Frame number offset
Null column allowed: Yes Default value:
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: No Default value:
LAYER
Text (50)
Name of the Hierarchical Cell Structure layer
Null column allowed: Yes Default value:
LAYER_RECEPTION_THRESH OLD
Float
If filled-in, takes precedence on the threshold value defined in the HCSLayers table
Null column allowed: Yes Default value:
LOSSES
Float
Losses due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
MAX_EXT_NEIGHB_NUMBER
Short
Maximum number of inter-technology neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Short
Maximum number of neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value:
MIN_RANGE
Integer
Minimum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous downlink losses
Null column allowed: Yes Default value:
38
This field marks a set of records in the TRGConfigurations tables (all the Null column allowed: Yes records for which TRG_CONFIG has the same value.) Each of these Default value: records specifies a TRG that should exist in this transmitter.
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MISCULL
Float
Miscellaneous uplink losses
Null column allowed: Yes Default value:
NAME
Text (50)
Template name
Null column allowed: No Default value:
NOISE_FIGURE
Float
Total noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value:
NUM_SECTORS
Integer
Number of sectors
Null column allowed: Yes Default value: 3
PBCCH_CELL_RESELECT_OFF SET
Integer
Cell reselection offset for GPRS cells with PBCCH in use (For future use)
Null column allowed: Yes Default value:
PBCCH_IN_USE
Boolean
Packet Broadcast Control Channel used or not (For future use)
Null column allowed: No Default value:
PBCCH_RECEPTION_THRESH OLD
Float
Reception threshold value for GPRS cells with PBCCH in use (For future use)
Null column allowed: Yes Default value:
POWER
Float
Transmitter power
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate predictions
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value:
REQ_CHANNELS
Integer
Number of required physical channels
Null column allowed: Yes Default value:
REUSE_DISTANCE
Float
Typical reuse distance for assignments
Null column allowed: Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Default value:
TILT
Float
Mechanical downtilt of the main antenna
Null column allowed: Yes Default value:
TMA_NAME
Text (50)
Name of the Tower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TRX_MAX_NUMBER
Short
Maximum number of TRX that can be allocated by TRX dimensioning
Null column allowed: Yes Default value:
TX_TYPE
Short
Type of transmitter (0 = Normal; 1 = Interferer only)
Null column allowed: Yes Default value:
1.53 Transmitters Table For transmitters. Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value: True
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the main antenna
Null column allowed: Yes Default value: 0
BSIC
Text (10)
BSIC colour code (Base Station Identity Code) assigned to the station
Null column allowed: Yes Default value:
39
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
BSIC_DOMAIN
Text (50)
A text field pointing at the BSIC domain.
Null column allowed: Yes Default value:
BSIC_FROZEN
Boolean
AFP not allowed to modify BSIC.
Null column allowed: No Default value: False
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define the calculation area Unit: m
Null column allowed: Yes Default value: 4000
CALC_RADIUS2
Integer
Extended calculation radius
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value: 50
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CELL_IDENTITY
Integer
Cell identity
Null column allowed: Yes Default value:
CELL_RESELECT_OFFSET
Integer
Cell reselection offset
Null column allowed: Yes Default value: 0
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value: 2000
CELL_TYPE
This field identifies a set of records in the TRGConfigurations tables (all Null column allowed: Yes Text (50) the records that point to this cell-type) each of these records specifies a Default value: TRG that should exist in this transmitter.
CHANNELS
Text (255)
Physical channels allocated to the transmitter
Null column allowed: Yes Default value:
CODEC_EQUIPMENT
Text (50)
Associated Codec equipment (for voice services)
Null column allowed: Yes Default value:
CODING_SCHEME_NUMBER
Integer
The number of coding schemes supported by the GPRS/EDGE transmitters
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the transmitter
Null column allowed: Yes Default value:
CONTROL_CHANNEL
Integer
Physical channel used as Broadcast Control Channel (BCCH)
Null column allowed: Yes Default value:
COST_FACTOR
Double
Used by the AFP assign priorities to transmitters
Null column allowed: Yes Default value: 1
DX
Float
X coordinate relative to the site location
Null column allowed: Yes Default value: 0
DY
Float
Y coordinate relative to the site location
Null column allowed: Yes Default value: 0
EGPRS_EQUIPMENT
Text (50)
Name of the equipment assigned to the GPRS/EDGE station
Null column allowed: Yes Default value:
EIRP
Float
Transmitter’s effective isotropic radiated power
Null column allowed: Yes Default value: 43
ENABLE_EGPRS
Boolean
'Yes' enables you to consider the transmitter as a GPRS/EDGE station
Null column allowed: No Default value: False
FBAND
Text (20)
Name of the frequency band
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of feeder in DL
Null column allowed: Yes Default value: 0
FEEDERLENGTH_UL
Float
Length of feeder in UL
Null column allowed: Yes Default value: 0
FN_OFFSET
Integer
Frame Number offset
Null column allowed: Yes Default value: 0
40
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
FROZEN
Boolean
Only TRXs that are not frozen and belong to non-frozen cells can be assigned frequencies by the AFP.
Null column allowed: No Default value: False
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value: 25
HEXAGON_GROUP
Text (50)
Group of hexagons used to create this transmitter
Null column allowed: Yes Default value:
HOP_MODE
Text (25)
The hopping mode of the default traffic TRG in this transmitter.
Null column allowed: Yes Default value:
HSN_FROZEN
Boolean
Only TRGs belonging to non-HSN-frozen cells, and which have non_HSN_frozen configurations, can be assigned HSNs by the AFP.
Null column allowed: No Default value: False
LAYER
Text (50)
Name of the Hierarchical Cell Structure layer
Null column allowed: Yes Default value:
LAYER_RECEPTION_THRESH OLD
Float
If filled-in, takes precedence on the threshold value defined in the HCSLayers table
Null column allowed: Yes Default value:
LOSSES
Float
Losses due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value: 0
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum number of inter-technology neighbours for the transmitter
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Integer
Maximum number of neighbours for the transmitter
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value: 35000
MIN_RANGE
Integer
Minimum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value: 0
MISCDLL
Float
Miscellaneous DL loss
Null column allowed: Yes Default value: 0
MISCULL
Float
Miscellaneous UL loss
Null column allowed: Yes Default value: 0
NOISE_FIGURE
Float
Total noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
NUM_TRX
Float
The total number of TRXs in this transmitter. In the cases of no or Base band hopping, it must correspond to the number of channels in the CHANNELS field.
Null column allowed: Yes Default value: 0
PBCCH_CELL_RESELECT_OFF SET
Integer
Cell reselection offset for GPRS cells with PBCCH in use (For future use)
Null column allowed: Yes Default value: 0
PBCCH_IN_USE
Boolean
Packet Broadcast Control Channel used or not (For future use)
Null column allowed: No Default value: False
PBCCH_RECEPTION_THRESH OLD
Float
Reception threshold value for GPRS cells with PBCCH in use (For future use)
Null column allowed: Yes Default value: -102
POWER
Float
Transmitter power
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value: ’Default model’
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value: 0
REQ_CHANNELS
Integer
Number of required TRXs
Null column allowed: Yes Default value: 1
REUSE_DISTANCE
Float
Typical reuse distance for assignments
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
41
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
SITE_NAME
Text (50)
Name of the site on which the transmitter is located (from the Sites table)
Null column allowed: No Default value:
TILT
Float
Mechanical downtilt of the first antenna
Null column allowed: Yes Default value: 0
TMA_NAME
Text (50)
Name of the TMA equipment
Null column allowed: Yes Default value:
TRX_MAX_NUMBER
Short
Maximum number of TRX that can be allocated by TRX dimensionning
Null column allowed: Yes Default value: 16
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
TX_TYPE
Short
Type of transmitter (0 = Normal; 1 = Interferer only)
Null column allowed: Yes Default value: 0
1.54 TRGConfigurations Table For subcell types.
42
Field
Type
Description
Attributes
_8PSK_PWBCKFF
Float
Reduction of power due to 8PSK modulation
Null column allowed: Yes Default value: 3
ASSIGN_MODE
Text (25)
One of the two options: «Free» or «Group constrained».
Null column allowed: No Default value: ‘Free’
BAD_QUAL_UB
Float
Additional constraints on subcell quality (considered in AFP): maximum probability to have C/I lower than C_OVER_I_MIN.
Null column allowed: No Default value: 1
C_OVER_I_MIN
Float
Minimum C/I
Null column allowed: No Default value: 12
CELL_TYPE
Text (50)
First part of unique key.
Null column allowed: No Default value:
COST_FACTOR
Float
By default, 1. The cost factor will be used to increase or decrease the importance of subcells of this configuration.
Null column allowed: No Default value: 1
DEF_DTX
Boolean
This is a default value of a subcell specific parameter. It is set to true if the TRXs of the subcell use Discontinuous transmission
Null column allowed: No Default value: True
DEF_HOP_MODE
Text (25)
This is a default value of a subcell specific parameter. Hopping mode can be “Non Hopping”, “Base Band Hopping”, or “Synthesized Hopping”.
Null column allowed: No Default value: ‘Non Hopping’
DEF_MIN_RECEPTION
Float
This is a default value of a subcell specific parameter. It denotes the minimum received power required to be served by this subcell.
Null column allowed: No Default value: -102
DEF_POWER_OFFSET
Float
This is a default value of a subcell specific parameter: the average power offset with respect to the BCCH channel.
Null column allowed: No Default value: 0
DEF_TRX_EQUIPMENT
Text (25)
Default TRX equipment of TRXs belonging to this subcell
Null column allowed: Yes Default value:
FREQUENCY_DOMAIN
Text (50)
All frequencies assigned to TRXs of this configuration must belong to this domain. Domains contain grouping info as well.
Null column allowed: No Default value:
HR_RATIO
Float
Percentage of Half Rate voice traffic in the subcell.
Null column allowed: Yes Default value: 40
HSN_DOMAIN
Text (50)
All HSNs assigned to subcells of this configuration must belong to this domain.
Null column allowed: No Default value:
HSN_FROZEN
Boolean
Only subcells that point to non-hsn_frozen configurations in nonhsn_frozen cells can by be assigned HSNs by the AFP.
Null column allowed: No Default value: False
MAXIMAL_MAL
Integer
Limitation on length of the MAL (Mobile allocation list).
Null column allowed: No Default value: 48
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MEAN_POWER_CONTROL
Float
Average value of DL power control
Null column allowed: Yes Default value: 0
TRAFFIC_OVERFLOW_TARGE T
Float
The percentage of traffic that is considered to overflow from the subcell.
Null column allowed: Yes Default value: 0
TRX_TYPE
Text (15)
Second part of unique key
Null column allowed: No Default value:
TS_CONFIGURATION_NAME
Text (50)
Timeslot configuration
Null column allowed: Yes Default value:
TX_DIVERSITY_MODE_DL
Short
If more than one antenna are used (TX_DIVERSITY_NBANT), this field indicates if they are used 0- simultaneously (TXDiv) or 1- alternatively (antenna hopping)
Null column allowed: Yes Default value: 0
TX_DIVERSITY_NBANT
Short
TX diversity Choice list: 1=No TX diversity; 2=TX diversity with 2 antennas;
Null column allowed: Yes Default value: 1
1.55 TRGs Table For subcells. Field
Type
Description
Attributes
_8PSK_PWBCKFF
Float
Power reduction due to 8PSK modulation
Null column allowed: Yes Default value: 3
AFP_BLOCKED_COST
Float
Secondary AFP quality indicator
Null column allowed: Yes Default value: 0
AFP_CONGESTION
Float
Secondary AFP indicator depicting the spectral congestion state
Null column allowed: Yes Default value: 0
AFP_COST
Float
Main AFP quality indicator
Null column allowed: Yes Default value: 0
AFP_FREEZE_DIM
Boolean
Permit the AFP to not always respect the number of required TRXs
Null column allowed: No Default value: False
AFP_SEP_COST
Float
Secondary AFP quality indicator
Null column allowed: Yes Default value: 0
ASSIGN_MODE
Text (25)
One of the two options: “Free” or “Group constrained”.
Null column allowed: Yes Default value: ‘Free’
BAD_QUAL_UB
Float
BLOCKING_PROBA
Float
Blocking probability (%)
Null column allowed: Yes Default value: 0
C_OVER_I_MIN
Float
Minimum C/I
Null column allowed: Yes Default value: 12
COST_FACTOR
Float
By default, 1. The cost factor is used to increase or decrease the importance of subcells of this configuration.
Null column allowed: Yes Default value: 1
CS_ERLANGS
Float
Circuit switched demand in Erlangs
Null column allowed: Yes Default value: 0
DEF_TRX_EQUIPMENT
Text (25)
Default TRX equipment of TRXs belonging to this subcell
Null column allowed: Yes Default value:
DTX
Boolean
It is set to true if the TRXs of the subcell use Discontinuous transmission.
Null column allowed: No Default value: True
DTX_GAIN_DL
Float
Downlink Gain due to DTX (dB)
Null column allowed: Yes Default value: 0
EFFECTIVE_TRAFFIC_OVERFL OW
Float
Effective traffic overflow
Null column allowed: Yes Default value:
EXCLUDED
Text (250)
List of frequencies which should not be used by TRX of the current subcell.
Null column allowed: Yes Default value:
FREQUENCY_DOMAIN
Text (50)
Additional constraints on subcell quality (considered in AFP): maximum Null column allowed: Yes probability to have C/I lower than C_OVER_I_MIN. Default value: 1
All frequencies assigned to TRXs of this configuration must belong to this Null column allowed: Yes domain. Domains contain grouping info as well. Default value:
43
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
HOP_MODE
Text (25)
The hopping mode of a subcell can be “Non Hopping”, “Base Band Hopping”, or “Synthesized Hopping”.
Null column allowed: Yes Default value: ‘Non Hopping’
HR_RATIO
Float
Percentage of Half rate traffic in the subcell.
Null column allowed: Yes Default value: 40
HSN
Integer
Assigned HSN.
Null column allowed: Yes Default value:
HSN_DOMAIN
Text (50)
All HSNs assigned to subcells of this configuration must belong to this domain.
Null column allowed: Yes Default value:
HSN_FROZEN
Boolean
Only subcells that point to non-hsn_frozen configurations in nonhsn_frozen cells can be assigned HSNs by the AFP.
Null column allowed: No Default value: False
MAXIMAL_MAL
Integer
Limitation on length of the MAL (Mobile allocation list).
Null column allowed: Yes Default value: 48
MEAN_POWER_CONTROL
Float
Average value of DL power control
Null column allowed: Yes Default value: 0
MIN_RECEPTION
Float
Minimum reception power required to be served by this subcell.
Null column allowed: No Default value: -102
POWER_OFFSET
Float
The average power offset with respect to the BCCH channel.
Null column allowed: No Default value: 0
PREFERRED_FREQ_GROUP
Text (50)
Frequency group which should be used if possible
Null column allowed: Yes Default value:
PS_DATA_ERLANGS
Float
Packet switched demand in data Erlangs (equivalent to avaraged used time slots)
Null column allowed: Yes Default value: 0
REQ_CHANNELS
Integer
Number of required channels.
Null column allowed: No Default value: 0
SYNCHRO_NAME
Text (50)
Defines synchronization sets.
Null column allowed: Yes Default value:
TRAFFIC_LOAD
Float
TRAFFIC_LOAD = (Traffic in Erlangs) / (NUM_TRX * Multyplexing_factor ) (Where, Multiplexing_factor = 8).
Null column allowed: No Default value: 1
TRAFFIC_OVERFLOW_TARGE T
Float
The percentage of traffic that is considered to overflow from one subcell.
Null column allowed: Yes Default value: 0
TRX_TYPE
Text (15)
Second part of a unique key. Points to the TRX type table.
Null column allowed: No Default value:
TS_CONFIGURATION_NAME
Text (50)
Timeslot configuration
Null column allowed: Yes Default value:
TX_DIVERSITY_MODE_DL
Short
If more than one antenna are used (TX_DIVERSITY_NBANT), this field indicates if they are used 0- simultaneously (TXDiv) or 1- alternatively (antenna hopping)
Null column allowed: Yes Default value: 0
TX_DIVERSITY_NBANT
Short
TX diversity Choice list: 1=No TX diversity; 2=TX diversity with 2 antennas;
Null column allowed: Yes Default value: 1
TX_ID
Text (50)
First part of a unique key. It is the transmitter to which this subcell belongs. (The cell type can be retrieved by following this link).
Null column allowed: No Default value:
UL_TRAFFIC_LOAD
Float
Subcell’s Uplink Traffic load
Null column allowed: Yes Default value: 1
VAMOS_RATIO
Float
Percentage of VAMOS (Voice services over Adaptive Multi-user channels Null column allowed: Yes on One Slot) traffic in the subcell. Default value: 0
1.56 TRXEquipments Table For TRX equipment. Field _8PSK_POWER
44
Type Float
Description
Attributes
Nominal output power in 8PSK modulation
Null column allowed: Yes Default value: 44
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
COMMENT_
Text (100)
Comments
Null column allowed: Yes Default value:
GMSK_POWER
Float
Nominal output power in GMSK modulation
Null column allowed: Yes Default value: 47
MAX_CS
Short
Highest coding scheme (CS) available for GPRS
Null column allowed: No Default value: 4
MAX_MCS
Short
Highest coding scheme (MCS) available for EDGE
Null column allowed: No Default value: 12
NAME
Text (25)
Name of TRX equipment
Null column allowed: No Default value:
1.57 TRXs Table For TRXs. Field
Type
Description
Attributes
_8PSK_PWBCKFF
Float
Reduction of power due to 8PSK modulation
Null column allowed: Yes Default value: 3
AFP_RANK
Short
Rank of this TRX according to the AFP
Null column allowed: Yes Default value: 0
CN_LIST
Text (255)
List of all frequencies assigned to a TRX. (separated with spaces)
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value: 0
FROZEN
Boolean
Allows/disallows changing parameters of this TRX.
Null column allowed: No Default value: False
MAIO
Integer
Assigned MAIO (Mobile Allocation Index Offset).
Null column allowed: Yes Default value:
TRX_EQUIPMENT
Text (25)
TRX equipment of this TRX
Null column allowed: Yes Default value:
TRX_NUMBER
Integer
An order on TRXs in the same subcell. It is the second part of a unique key.
Null column allowed: No Default value:
TRX_TYPE
Text (15)
The couple TX_ID, TRG_TYPE is the key of the TRGs table to which this TRX belongs
Null column allowed: No Default value:
TX_ID
Text (50)
First part of a unique key. It points to Transmitters. The value of the field CELL_TYPE in the Transmitters table can therefore be retrieved and can serve in order to access relevant information in the TRGConfigurations table.
Null column allowed: No Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value: 0
UPLINK_NOISE_RISE
Float
Uplink noise rise
Null column allowed: Yes Default value: 0
1.58 TRXTypes Table For TRX types (BCCH, TCH, TCH_INNER, etc.). Field
Type
Description
Attributes
IS_BCCH
Boolean
Indicates that a TRG_TYPE is the Common Broadcast carrier. Tests in the code will verify that only one type carries the broadcast.
Null column allowed: No Default value: False
IS_TCH_DEF
Boolean
Indicates that a TRG_TYPE is the default traffic carrier (the OUTER zone). Tests in the code will verify that only one type is the default TCH.
Null column allowed: No Default value: False
NAME
Text (15)
Type of TRX
Null column allowed: No Default value:
PRIORITY
Short
Priority of a certain type of TRX to carry traffic (largest value has the highest priority)
Null column allowed: Yes Default value: 0
45
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
TRAFFIC_POOL
Short
All TRXs of the same pool can exchange traffic if they need to balance their loads. If they are in different pools, the load balancing might fail.
Null column allowed: Yes Default value: 1
1.59 TSConfigurationNames Table For names of timeslot configurations. Field
Type
NAME
Text (50)
Description
Attributes
Name of the configuration
Null column allowed: No Default value:
1.60 TSConfigurations Table For timeslot configurations. Field
Type
Description
Attributes
CIRCUIT_TS
Integer
Number of timeslots that support circuit switched traffic
Null column allowed: No Default value: 0
COMPOSITE_TS
Integer
Number of timeslots that support circuit and packet switched traffic
Null column allowed: No Default value: 8
NAME
Text (50)
Name of the configuration
Null column allowed: No Default value:
PACKET_TS
Integer
Number of timeslots that support packet switched traffic
Null column allowed: No Default value: 0
TRX_NUMBER
Integer
Zero based index of TRX
Null column allowed: No Default value: 1
1.61 TxsLists Table For transmitters belonging to transmitter lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list.
Null column allowed: No Default value:
TX_NAME
Text (50)
Second part of the unique key. Name of the transmitter.
Null column allowed: No Default value:
1.62 TxsListsNames Table For names of transmitter lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the transmitter list
Null column allowed: No Default value:
1.63 Units Table For the reception and transmission units, the projection coordinate system specified in the ATL document, the database internal coordinate system, and the internal BSIC format.
46
Field
Type
Description
Attributes
BSIC_FORMAT
Integer
BSIC format Choice list: 0=Decimal; 1=Octal;
Null column allowed: Yes Default value: 1
COORD_SYSTEM
Integer
Display coordinate system when creating database
Null column allowed: Yes Default value: -1
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
GAIN_UNIT
Integer
Unit used for gains (dBd or dBi) Choice list: 0=dBd; 1=dBi;
Null column allowed: Yes Default value: 0
PROJECTION
Integer
Projected coordinate system for geo data
Null column allowed: Yes Default value: -1
RECEPTION_UNIT
Integer
Reception unit when creating database Choice list: 0=dBm; 1=dbµV; 2=dbµV/m;
Null column allowed: No Default value: 0
TRANSMISSION_UNIT
Integer
Transmission unit when creating database Choice list: 0=dBm; 1=Watts; 2=kWatts;
Null column allowed: No Default value: 0
47
Atoll 3.2.1 Data Structure Reference Guide Chapter 1: GSM GPRS EDGE Data Structure
48
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
2 UMTS HSPA Data Structure Atoll supports integrated network planning for UMTS networks. This section describes the UMTS HSPA data structure used in Atoll. Figure 2.1 on page 49, Figure 2.2 on page 50, and Figure 2.3 on page 51 depict the structure of the UMTS HSPA database. The following subsections list the tables in the UMTS HSPA database template.
Figure 2.1: UMTS HSPA Template - 1
49
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Figure 2.2: UMTS HSPA Template - 2
50
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Figure 2.3: UMTS HSPA Template - 3
51
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
2.1 Data Structure Changes Between Atoll 3.1 to 3.2 2.1.1 Added Tables and Fields Antennas Table Field
Type
Description
Attributes
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
CdmaCells Table Field
Type
Description
Attributes
HSDPA_SCHEDULER
Text (50)
HSDPA scheduler
Null column allowed: Yes Default value:
RSCP_MIN
Float
Minimum RSCP reception level (dBm)
Null column allowed: Yes Default value: -150
CdmaEquipments Table Field
Type
Description
Attributes
HSDPA_MULTI_BAND
Short
MultiBand activation 0=Inactive; 1=Active
Null column allowed: No Default value: 0
SCHEDULER_ALGO
Text (50)
Scheduler
Null column allowed: Yes Default value:
CustomFields Table Field
Type
Description
Attributes
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
FrequencyBands Table Field
Type
Description
Attributes
DELTA_CN
Integer
Step between two adjacent carrier numbers
Null column allowed: Yes Default value: 1
EXCLUDED_CHANNELS
Text (255)
List of the forbidden carriers inside this band
Null column allowed: Yes Default value:
HSUPAUECategories Table Field
Type
Description
Attributes
MULTI_CARRIER
Short
Multi-carrier mode (0: None; 1: Dual-cell)
Null column allowed: No Default value: 0
MUGTables Table (New)
52
Field
Type
Description
Attributes
CELL_NUMBER
Short
The multi-user diversity gain may be different if the number of cells increase.
Null column allowed: No Default value: 0
MUG_TABLE
Memo
Multi-user diversity gain table
Null column allowed: Yes Default value:
SCHEDULER_NAME
Text (50)
Name of the scheduler for which the multi-user diversity gain table is defined.
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Neighbours Table Field
Type
Description
Attributes
RELATION_TYPE
Short
The type of the neighbour relation between cells: intra-carrier or intercarrier
Null column allowed: Yes Default value:
Schedulers Table (New) Field
Type
Description
Attributes
NAME
Text (30)
Name of the scheduler
Null column allowed: No Default value:
SCHEDULING_METHOD
Short
0 = Max C/I; 1 = Round-robin; 2 = Proportional Fair
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
Sites Table
TplTransmitters Table Field
Type
Description
Attributes
HSDPA_SCHEDULER
Text (50)
HSDPA scheduler
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
MIMO_SUPPORT
Short
Supported MIMO features: 0 = None; 1 = open loop MIMO; 2 = closed loop MIMO
Null column allowed: Yes Default value:
RSCP_MIN
Float
Minimum RSCP reception level (dBm)
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
Transmitters Table Field
Type
Description
Attributes
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
UMTSTerminals Table Field
Type
Description
Attributes
NOISE_FACTOR_THIRD
Float
Noise figure used to determine the thermal noise at the receiver (for third frequency band)
Null column allowed: Yes Default value: 8
THIRD_BAND
Text (50)
Third frequency band
Null column allowed: Yes Default value:
2.1.2 Deleted Tables and Fields CdmaCells Table • •
HSDPA_MUG_TABLE HSDPA_SCHEDULER_ALGO
Networks Table •
DEFAULT_ORTHO_FACTOR
53
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Sites Table •
SUPPORT_NATURE
TplTransmitters Table • • • •
HSDPA_MUG_TABLE HSDPA_SCHEDULER_ALGO MC_HSDPA_MUG MC_HSDPA_SCHED_ALGO
Transmitters Table • •
MC_HSDPA_MUG MC_HSDPA_SCHED_ALGO
2.2 Antennas Table For antennas. Field
Type
Description
Attributes
Beamwidth
Float
Antenna beamwidth
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about antenna
Null column allowed: Yes Default value:
CONSTRUCTOR
Text (50)
Antenna manufacturer name
Null column allowed: Yes Default value:
DIAGRAM
Binary
Antenna horizontal and vertical patterns
Null column allowed: Yes Default value:
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
ELECTRICAL_TILT
Float
Antenna electrical tilt (for information)
Null column allowed: Yes Default value:
FMax
Double
Maximum operating frequency of the antennas Unit: MHz
Null column allowed: Yes Default value:
FMin
Double
Minimum operating frequency of the antenna Unit: MHz
Null column allowed: Yes Default value:
GAIN
Float
Antenna isotropic gain Unit: dBi
Null column allowed: No Default value: 0
NAME
Text (50)
Name of antenna
Null column allowed: No Default value:
PHYSICAL_ANTENNA
Text (50)
Physical antenna name
Null column allowed: Yes Default value:
The format of the binary field, DIAGRAM, is described in the "RF 2D Antenna Pattern Format" on page 275.
2.3 BTSEquipments Table For NodeB equipment. Field
54
Type
Description
Attributes
CONFIG_DL_LOSSES
Float
Downlink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
CONFIG_UL_LOSSES
Float
Uplink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Base Station Equipment
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
NOISE_FIGURE
Float
Noise figure of Base Station
Null column allowed: Yes Default value: 0
RHO_FACTOR
Short
Rho factor to model self generated interference (100%=ideal)
Null column allowed: Yes Default value: 100
2.4 CDMACells Table For cells. Field
Type
Description
Attributes
ACTIVE
Boolean
Cell's activity: 'Yes' means that the cell is active
Null column allowed: No Default value: True
AS_THRESHOLD
Float
Maximum difference with the best-server to enter active Set (dB)
Null column allowed: Yes Default value: 5
CARRIER
Integer
Carrier number
Null column allowed: Yes Default value: 0
CELL_ID
Text (50)
Name of the cell
Null column allowed: No Default value:
CELL_IDENTITY
Integer
Cell identity
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the cell
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value: 0
DYN_HS_SCCH_POWER_ALL OC
Boolean
Allocation of power for HS-SCCH (True=Dynamic, False=Static)
Null column allowed: No Default value: True
DYN_HSDPA_POWER_ALLOC
Boolean
Allocation of power for HSDPA (True=Dynamic, False=Static)
Null column allowed: No Default value: False
HS_SCCH_POWER
Float
Value of power dedicated to a HS-SCCH channel. In case of dynamic allocation, it is the maximum available power.
Null column allowed: Yes Default value:
HSDPA_MAX_CODES
Short
Maximum number of HS-PDSCH codes
Null column allowed: Yes Default value: 16
HSDPA_MAX_USERS
Short
Max number of HSDPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value: 64
HSDPA_MIN_CODES
Short
Minimum Number of HS-PDSCH codes
Null column allowed: Yes Default value: 1
HSDPA_PWR
Float
Amount of power (dBm) dedicated to HSDPA
Null column allowed: Yes Default value:
HSDPA_SCHEDULER
Text (50)
HSDPA scheduler
Null column allowed: Yes Default value:
HSPA_SUPPORT
Short
HSPA features supported: 0=None; 1=HSDPA; 2=HSPA; 3=HSPA+
Null column allowed: No Default value: 0
HSUPA_DLPOWER
Float
Amount of power (dBm) dedicated to HSUPA DL channels (E-AGCH, ERGCH, E-HICH)
Null column allowed: Yes Default value:
HSUPA_MAX_USERS
Short
Max number of HSUPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value: 15
HSUPA_UL_LOAD
Float
Uplink cell load factor due to HSUPA users: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
LOCKED_SC
Boolean
Field used to freeze allocated SC of the cell during automatic allocation
Null column allowed: No Default value: False
MAX_DL_LOAD
Float
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum downlink load allowed (percentage of max power used). Used Null column allowed: Yes in power control simulation Default value: 50 Maximum number of inter-technology neighbours for the cell
Null column allowed: Yes Default value:
55
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MAX_INTERCAR_NEIGHB_NB
Integer
Maximum number of inter-carrier neighbours for this cell
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Integer
Maximum number of neighbours for the cell
Null column allowed: Yes Default value:
MAX_R99BEARER_DL_RATE
Float
Max bearer rate available in DL (kbps)
Null column allowed: Yes Default value: 1000
MAX_R99BEARER_UL_RATE
Float
Max bearer rate available in UL (kbps)
Null column allowed: Yes Default value: 1000
MAX_UL_LOAD
Float
Maximum uplink load allowed (percentage). Used in power control simulation
Null column allowed: Yes Default value: 75
MIMO_SUPPORT
Short
MIMO features supported: 0=None; 1=Transmit Diversity; 2=SU-MIMO;
Null column allowed: No Default value: 0
NUM_HS_SCCH
Short
Number of HS-SCCH channels
Null column allowed: Yes Default value: 1
NUM_HSDPA_USERS
Short
Number of served HSDPA users in the cell: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
NUM_HSUPA_USERS
Short
Number of served HSUPA users in the cell: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
OTHERS_CCH_POWER
Float
Power of other common channels except SCH
Null column allowed: Yes Default value: 30
PILOT_POWER
Float
Power of the pilot channel
Null column allowed: Yes Default value: 33
POWER_MAX
Float
Maximum power supported by the transmitter
Null column allowed: Yes Default value: 43
PWR_HEADROOM
Float
Power Control Headroom (dB) for DCH (used in WCDMA simulation algorithm)
Null column allowed: Yes Default value: 0
REUSE_DIST
Float
Minimum reuse distance for scrambling codes
Null column allowed: Yes Default value:
RSCP_MIN
Float
Min RSCP reception level (dBm)
Null column allowed: Yes Default value: -150
SC_DOMAIN_NAME
Text (50)
Scrambling code domain name.
Null column allowed: Yes Default value:
SCH_POWER
Float
Power of the synchronisation (SCH) channel
Null column allowed: Yes Default value: 21
SCRAMBLING_CODE
Integer
Scrambling code.
Null column allowed: Yes Default value:
TOTAL_POWER
Float
Total downlink power: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
TX_ID
Text (50)
Name of the transmitter
Null column allowed: No Default value:
UL_LOAD
Float
Uplink transmitter load factor: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UL_REUSE_FACTOR
Float
Uplink (I intra+ I extra)/ I intra: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value: 0
2.5 CdmaEqptsHSUPARssUse Table For HSUPA resource consumption in site equipment. Field BEARER_INDEX
56
Type Short
Description
Attributes
Cell identity
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
CHANNEL_ELTS_UL
Integer
Inter-network downlink noise rise
Null column allowed: Yes Default value: 1
EQUIPMENT
Text (50)
Name of the site equipment
Null column allowed: No Default value:
IUB_RATE_UL
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value: 15
2.6 CDMAEquipments Table For site equipment. Field
Type
Description
Attributes
Carrier selection mode Null column allowed: No Choice list: 0=Min UL noise; 1=Min DL power; 2=Random; 3=Sequential; Default value: 0
CARRIER_SELECTION
Short
CES_OVERHEAD_DL
Integer
Number of channel elements used for DL overhead channels (pilot, synchro, ...)
Null column allowed: No Default value: 0
CES_OVERHEAD_UL
Integer
Number of channel elements used for UL overhead channels (pilot, synchro, ...)
Null column allowed: No Default value: 0
ENABLE_COMPRESSED_MOD E
Boolean
If true, NodeBs of the site can manage compressed mode
Null column allowed: No Default value: False
HSDPA_MULTI_BAND
Short
MultiBand activation 0=Inactive; 1=Active
Null column allowed: No Default value: 0
IUB_E1_RATE
Float
Supported rate per E1 line (kbps)
Null column allowed: No Default value: 2048
IUB_HSDPA_PERCENT
Short
Iub HSDPA Backhaul Overhead (%)
Null column allowed: No Default value: 20
IUB_OVERHEAD_DL
Float
Iub Common Transport Channel Backhaul Overhead per cell (rate in kps)
Null column allowed: No Default value: 40
MANUFACTURER
Text (50)
Name of the manufacturer
Null column allowed: Yes Default value:
MUD_FACTOR
Float
MUD factor for UL interference cancellation
Null column allowed: No Default value: 0
NAME
Text (50)
Equipment name
Null column allowed: No Default value:
RAKE_EFFICIENCY
Float
Efficiency of the rake receiver. Used for combination of AS member contributions
Null column allowed: No Default value: 1
SCHEDULER_ALGO
Text (50)
Scheduler
Null column allowed: Yes Default value:
USE_NEIGHBOURS
Boolean
If true, selection of AS members is limited to the neighbours of the selected transmitter
Null column allowed: No Default value: False
2.7 CDMAEquipmentsCEsUse Table For channel elements consumption in site equipment. Field
Type
Description
Attributes
CHANNEL_ELTS_DL
Integer
Number of channel elements used for downlink
Null column allowed: No Default value: 1
CHANNEL_ELTS_UL
Integer
Number of channel elements used for uplink
Null column allowed: No Default value: 1
EQUIPMENT
Text (50)
First part of the unique key. Name of equipment
Null column allowed: No Default value:
IUB_RATE_DL
Float
Iub backaul rate for downlink (kbps)
Null column allowed: Yes Default value: 15
57
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
IUB_RATE_UL
Float
Iub backaul rate for uplink (kbps)
Null column allowed: Yes Default value: 15
SERVICE
Text (50)
Second part of the unique key. Service name.
Null column allowed: No Default value:
2.8 CoordSys Table For the projection coordinate system and the database’s internal coordinate system ( this is the display coordinate system used when creating a database). Field
Type
Description
Attributes
CODE
Integer
Identification number of the coordinate system (the code of userdefined coordinate systems is an integer higher than 32768)
Null column allowed: No Default value: 0
DATUM_CODE
Double
DATUM_ROTX
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTY
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTZ
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_SCALE
Double
Parts per million (ppm)
Null column allowed: Yes Default value: 0
DATUM_SHIFTX
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTY
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTZ
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_CODE
Integer
ELLIPS_RMAJOR
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_RMINOR
Double
Meters
Null column allowed: Yes Default value: 0
NAME
Text (50)
Coordinate system name
Null column allowed: No Default value:
PROJ_ANGLE
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_FALSE_EASTING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FALSE_NORTHING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FIRST_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LATITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LONGITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_METHOD
Short
UTM, Undefined, NoProjection, Lambert1SP, Lambert2SP, Mercator, CassiniSoldner, TransMercator, TransMercatorSO, ObliqueStereographic, NewZealandMapGrid, HotineOM, LabordeOM, SwissObliqueCylindical
Null column allowed: Yes Default value: 0
PROJ_SCALE_FACTOR
Double
58
Null column allowed: Yes Default value: 0
Null column allowed: No Default value: 0
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
PROJ_SECOND_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_ZONE_NUMBER
Integer
Used with UTM
Null column allowed: Yes Default value: 0
2.9 CustomFields Table For defining user-defined fields added to tables, default values for any field (including user-defined fields), and choice lists, captions, and group names for user-defined fields. Field
Type
Description
Attributes
CAPTION
Text (50)
Caption of the field (displayed instead of the name)
Null column allowed: Yes Default value:
CHOICE_LIST
Memo
Choice list for the field
Null column allowed: Yes Default value:
CHOICE_TYPE
Integer
0=Choice list is optional; 1=Choice list is mandatory;
Null column allowed: Yes Default value: 0
COLUMN_NAME
Text (50)
Second part of the unique key. Field name
Null column allowed: No Default value:
DEFAULT_VALUE
Text (50)
Default value for the field
Null column allowed: Yes Default value:
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
GROUP_NAME
Text (50)
Name of the group to which that field belongs
Null column allowed: Yes Default value:
TABLE_NAME
Text (50)
First part of the unique key. Table name
Null column allowed: No Default value:
These are some general recommendations that you should follow when handling databases. General • • • •
In order to use Atoll with Oracle, you must create Oracle users and schema with names in uppercase. Create backups of the database before upgrading. It is recommended to define a rule for making backups of the database at regular intervals. Do not skip a major Atoll version. For example, if you are currently using Atoll 2.7.xV6.7, you should first upgrade the database to Atoll 2.8.xV6.9 before upgrading to Atoll 3.1.xV7.1. Upgrading your database will be simpler if you do not skip a major version. If you skip or have skipped an intermediate major version, you must upgrade your database twice in order to make it compatible with the new version.
Tables and Fields • •
Table and field names are case sensitive. Table and field names should be not more than 20 characters long. Oracle databases allow a maximum length of 30 characters for field and table names. However, for use in Atoll, you must not create tables and fields with names longer than 20 characters. This is because Atoll adds some characters to the table and field names for certain operations: creating associated triggers, creating project databases, etc. Limiting the length of table and field names to 20 characters will help avoid database connection and consistency problems.
• • • • • •
Table and field names should only use alphanumeric characters (A-Z, a-z, 0-9) and underscores (_). Table and field names must not start with a numeric character (0-9). Table and field names must not contain an SQL or RDBMS-specific keyword, such as ORDER, DATE, etc. Table and field names must not contain spaces or special characters, such as periods (.), exclamation marks (!), colons (:), semi-colons (;), interrogation marks (?), parentheses (()), brackets ({}), square brackets ([]), etc. Boolean fields, system or user-defined, should always have default values assigned. The CustomFields table enables you to define default values, choice lists, and read/write access for any field in any table in Atoll, including user-defined fields that you add to the Atoll tables. The values defined in this table have priority over the internal predefined default values. If you define floating point default values, make sure that all the users have the same decimal separator.
59
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
• •
© Forsk 2014
If you wish to add custom fields in the Atoll document, you should first add the field in the database, and then update your Atoll document from the database. When setting up your database for the first time, try to anticipate user requirements in terms of custom fields in Atoll tables. Some requirements of the different user groups can be satisfied if a few general-purpose user-defined fields are added in Atoll tables when setting up the database. For example, if you add three user-defined fields (one of type integer, float, and text (limited size)) to the Sites and Transmitters tables, users will be able to use these for sorting, filtering, grouping, or other purposes. This approach can help the database function a long time before users require the addition of other custom fields.
• •
•
To improve performance, if your projects allow it, reduce the size of the fields corresponding to the sites and transmitters’ names. To improve performance, unless absolutely necessary, do not add user-defined fields of Text type. Rather, use numeric field types, which allow sorting and other functions. If you must add Text fields, allocate them the appropriate size that would suffice. For example, a 255-character long Text type field would, for the most part, occupy disk space for no purpose. To improve performance, you should avoid adding custom fields to the neighbour management tables.
2.10 FeederEquipments Table For feeders. Field
Type
Description
Attributes
CONNECTOR_LOSSES_DL
Float
Feeder connector losses in downlink
Null column allowed: Yes Default value: 0
CONNECTOR_LOSSES_UL
Float
Feeder connector losses in uplink
Null column allowed: Yes Default value: 0
LOSS_PER_METER
Float
Feeder loss per meter
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Feeder
Null column allowed: No Default value:
2.11 FrequencyBands Table For frequency bands. Field
Type
Description
Attributes
BAND_WIDTH
Double
Bandwidth (MHz)
Null column allowed: Yes Default value: 5
DELTA_CN
Integer
Step between two adjacent carrier numbers
Null column allowed: Yes Default value: 1
EXCLUDED_CHANNELS
Text (255)
List of the forbidden carriers inside this band
Null column allowed: Yes Default value:
FIRST_CARRIER
Integer
Number of the first carrier available on the network
Null column allowed: Yes Default value: 0
FREQUENCY
Double
Average frequency of carriers Unit: MHz
Null column allowed: Yes Default value: 2110
LAST_CARRIER
Integer
Number of the last carrier available on the network
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the frequency band
Null column allowed: No Default value:
SPREADING_WIDTH
Double
Spreading bandwidth definition
Null column allowed: Yes Default value: 3.84
2.12 HSDPABearers Table For HSDPA bearers.
60
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
BEARER_INDEX
Short
Unique key to address bearer
Null column allowed: No Default value:
HSPDSCH_NUM
Short
Number of HS_PDSCH channels used
Null column allowed: Yes Default value: 5
MODULATION
Short
Modulation (0: QPSK; 1: 16QAM; 2: 64QAM)
Null column allowed: No Default value: 0
RLC_PEAK_THROUGHPUT
Float
Peak RLC throughput (without BLER consideration)
Null column allowed: Yes Default value: 0
TRANSPORT_BL_SIZE
Integer
Transport Block Size (bits)
Null column allowed: Yes Default value: 0
2.13 HSDPABearerSelectTables Table For HSDPA bearer selection graphs. Field
Type
Description
Attributes
BEST_BEARER_TABLE
Memo
Tables BEST_BEARER_INDEX=f(CQI_HSPDSCH)
Null column allowed: Yes Default value:
CQI_TABLE
Memo
Tables CQI=f(Quality) , Quality defined by CQI_CPICH_BASED in Networks table
Null column allowed: Yes Default value:
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: Yes Default value:
2.14 HSDPAQualityTables Table For HSDPA bearer performance graphs. Field
Type
Description
Attributes
BEARER_INDEX
Short
Bearer index
Null column allowed: No Default value:
DL_QI_TABLE
Memo
QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
QI_NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: No Default value:
2.15 HSPAMIMOConfigs Table For HSPA MIMO gains. Field
Type
Description
Attributes
DL_DIVERSITY_GAIN
Float
Downlink diversity gain (D-TxAA)
Null column allowed: Yes Default value: 0
HSDPA_BEARER_INDEX
Short
HSDPA Bearer index
Null column allowed: Yes Default value: 0
MAX_MIMO_GAIN_TABLE
Memo
Maximum spatial multiplexing capacity gain graphs
Null column allowed: Yes Default value:
MIMO_RX_ANTENNAS
Short
Number of reception antennas used for MIMO
Null column allowed: Yes Default value: 1
61
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MIMO_TX_ANTENNAS
Short
Number of transmission antennas used for MIMO
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: No Default value:
2.16 HSUPABearers Table For HSUPA bearers. Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of the bearer
Null column allowed: No Default value:
EDPDCH_NUM
Short
Number of E-DPDCH codes used
Null column allowed: Yes Default value:
MIN_SF
Integer
Smallest Spreading Factor
Null column allowed: Yes Default value:
MODULATION
Short
Modulation (0: QPSK; 1: 16QAM)
Null column allowed: No Default value: 0
RLC_PEAK_RATE
Float
Peak RLC throughput (without BLER)
Null column allowed: Yes Default value:
TRANSPORT_BL_SIZE
Integer
Transport Block Size (bits)
Null column allowed: Yes Default value:
TTI_LENGTH
Float
Duration of TTI (ms)
Null column allowed: Yes Default value:
2.17 HSUPABearerSelection Table For HSUPA bearer selection thresholds. Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of the selected bearer
Null column allowed: Yes Default value: 0
EARLY_TERM_TABLE
Memo
Tables of probabilities of earlier termination=f(REPEAT_NUM)
Null column allowed: Yes Default value:
EC_NT_REQ
Float
Required E-DPDCH Ec/Nt
Null column allowed: Yes Default value:
MOBILITY
Text (50)
User’s mobility
Null column allowed: Yes Default value:
REPEAT_NUM
Integer
Number of retransmissions to ensure a correct transmission
Null column allowed: Yes Default value: 1
RX_EQUIP
Text (50)
Reception equipment of the terminal
Null column allowed: Yes Default value:
2.18 HSUPAQualityTables Table For HSUPA bearer performance graphs. Field
62
Type
Description
Attributes
BEARER_INDEX
Short
Bearer index
Null column allowed: No Default value:
MOBILITY
Text (50)
User’s mobility
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
QI_NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
REPEAT_NUM
Integer
Number of retransmissions to ensure a correct transmission
Null column allowed: Yes Default value: 1
RX_EQUIP
Text (50)
Reception equipment of the terminal
Null column allowed: No Default value:
UL_QI_TABLE
Memo
QI=f(MEAS_PARAM), where MEAS_PARAM is read from the QualityIndicators table
Null column allowed: Yes Default value:
2.19 HSUPAUECategories Table For HSUPA UE categories. Field
Type
Description
Attributes
MAX_BLOCK_SIZE_10MS
Integer
Maximum transport block size supported for TTI=10ms (bits)
Null column allowed: Yes Default value:
MAX_BLOCK_SIZE_2MS
Integer
Maximum transport block size supported for TTI=2ms (bits)
Null column allowed: Yes Default value:
MAX_EDPDCH_NUM
Short
Maximum number of E-DPDCH codes for HSUPA
Null column allowed: Yes Default value:
MIN_SF
Integer
Smallest Spreading Factor supported
Null column allowed: Yes Default value:
MODULATION
Short
Modulation (0: QPSK; 1: 16QAM)
Null column allowed: No Default value: 0
MULTI_CARRIER
Short
Multi-carrier mode (0: None; 1: Dual-cell)
Null column allowed: No Default value: 0
TTI_2MS
Boolean
True if TTI=2ms is supported
Null column allowed: No Default value: False
UE_CATEGORY
Short
UE category for HSUPA
Null column allowed: No Default value:
UE_CATEGORY_NAME
Text (50)
Name of the HSUPA UE category
Null column allowed: Yes Default value:
2.20 InterfReductionFactors Table For interference reduction factors between carriers. Field
Type
Description
Attributes
CARRIER1
Integer
First carrier
Null column allowed: No Default value: 0
CARRIER2
Integer
Second carrier
Null column allowed: No Default value: 0
FACTOR
Double
Interference reduction factor
Null column allowed: No Default value: 200
2.21 InterNetChProtect Table For inter-network interference reduction factor graphs. Field
Type
Description
Attributes
ICP
Memo
Inter-network channel protection = f( MHz)
Null column allowed: Yes Default value:
ITF_BW
Double
Interfering bandwidth (kHz)
Null column allowed: No Default value: 0
63
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
ITF_TECHNO
Text (50)
Interfering technology
Null column allowed: No Default value:
V_BW
Double
Victim bandwidth (kHz)
Null column allowed: No Default value: 0
2.22 MUGTables Table For multi-user diversity gains. Field
Type
Description
Attributes
CELL_NUMBER
Short
The multi-user diversity gain may be different if the number of cells increase.
Null column allowed: No Default value: 0
MUG_TABLE
Memo
Multi-user diversity gain table
Null column allowed: Yes Default value:
SCHEDULER_NAME
Text (50)
Name of the scheduler for which the multi-user diversity gain table is defined.
Null column allowed: No Default value:
2.23 Neighbours Table For intra-technology neighbour relations. Field
Type
Description
Attributes
FORCE_HHO
Boolean
Force Handover type to hard handover in case of intra-carriers neighbours
Null column allowed: No Default value: False
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
RELATION_TYPE
Short
The type of the neighbour relation between cells: intra-carrier or intercarrier
Null column allowed: Yes Default value:
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
2.24 NeighboursConstraints Table For intra-technology neighbour allocation constraints.
64
Field
Type
Description
Attributes
FORCE_HHO
Boolean
Force Handover type to hard handover in case of intra-carriers neighbours
Null column allowed: No Default value: False
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
2.25 NeighboursConstraintsExt Table For inter-technology neighbour allocation constraints. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50) Second part of the unique key. List of neighbours from another project.
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
2.26 NeighboursExt Table For inter-technology neighbour relations. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50) Second part of the unique key. List of neighbours from another project
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
2.27 Networks Table For network-level parameters. Field
Type
Description
Attributes
ADD_MRC_SOFTERSOFT
Boolean
If true, gain due to MRC is taken into account for softer/soft cases
Null column allowed: No Default value: False
COMPRESSED_DELTA_DL_Q UAL
Float
Eb/Nt DL target overhead due to compressed mode activated
Null column allowed: No Default value: 1
COMPRESSED_DELTA_UL_Q UAL
Float
Eb/Nt UL target overhead due to compressed mode activated
Null column allowed: No Default value: 1
COMPRESSED_ON_ECIO
Boolean
Compressed mode activated on Ec/Io threshold (for future use)
Null column allowed: No Default value: True
COMPRESSED_ON_RSCP
Boolean
Compressed mode activated on RSCP threshold (for future use)
Null column allowed: No Default value: False
COMPRESSED_THRESHOLD
Float
Ec/Io threshold for compressed mode activation
Null column allowed: No Default value: -13
CQI_CPICH_BASED
Boolean
CQI determination ids based on CPICH quality (true) or on HS-PDSCH quality (false)
Null column allowed: No Default value: True
DEFAULT_HOGAIN_UL
Float
Default soft handoff gain uplink
Null column allowed: No Default value: 0
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: ‘Cost-Hata’
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
65
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
HSDPA_NTISNTOT
Boolean
Nt includes or not pilot's signal for HS-SCCH, HS-PDSCH and CPICH for CQI determination
Null column allowed: No Default value: False
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -130
IOISNTOT
Boolean
Io includes pilot signal or not
Null column allowed: No Default value: True
NAME
Text (50)
NTISNTOT
Boolean
Nt includes pilot signal or not
Null column allowed: No Default value: False
POWERS_RELATIVE_TO_PILO T
Boolean
Cell paging and Synchro powers, Service Allowed DL min and max TCH powers are absolute values or relative to cell pilot power
Null column allowed: No Default value: False
PTOT_RELATIVE_TO_PMAX
Boolean
Cell total power is absolute value (dBm) or relative to Cell maximum power (%)
Null column allowed: No Default value: False
RSCP_COMPRESSED_THRESH OLD
Float
RSCP threshold for compressed mode activation (for future use)
Null column allowed: No Default value: -100
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SPREADING_WIDTH
Float
Spreading width (MHz)
Null column allowed: Yes Default value: 3.84
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value: ‘UMTS’
TECHNOLOGY
Text (10)
Name of the technology
Null column allowed: No Default value: ‘CDMA’
Null column allowed: No Default value:
2.28 PropagationModels Table For propagation models. Field
Type
Description
Attributes
Data
Binary
Model specific parameters
Null column allowed: Yes Default value:
Description
Text (255)
User defined
Null column allowed: Yes Default value:
Name
Text (50)
Name of the propagation model
Null column allowed: No Default value:
Signature
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
Type
Text (50)
ProgID of the model
Null column allowed: No Default value:
2.29 QualityIndicators Table For quality indicators (BER, BLER, etc.).
66
Field
Type
Description
Attributes
CS_QI
Boolean
Flag which indicates if this indicator is used in CS services
Null column allowed: No Default value: True
MEAS_PARAM
Short
Name of the measured figure used for this QI determination Choice list: 1=CPICH_ECIO; 2=CPICH_CI; 3=CPICH_ECNT; 4=DCH_EBNT; 5=HSPDSCH_ECNT;
Null column allowed: Yes Default value: 1
NAME
Text (20)
Name of the managed quality indicator
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
PS_QI
Boolean
Flag which indicates if this indicator is used for PS services
Null column allowed: No Default value: True
USE_INTERPOLATION
Boolean
Flag which indicates if this QI must be interpolated or not
Null column allowed: No Default value: True
2.30 R99Bearers Table For release 99 bearers. Field
Type
Description
Attributes
ACTIVE_SPREADING_FACTOR _DL
Integer
DL Spreading Factor for active users
Null column allowed: Yes Default value: 256
DL_NOMINAL_BIT_RATE
Float
Bearer nominal rate in downlink Unit: kbps
Null column allowed: Yes Default value: 9.6
DPCCH_DPCH_RATIO_DL
Float
Ratio between DPCCH and DPCH powers in DL
Null column allowed: Yes Default value: 0
DPCCH_DPCH_RATIO_UL
Float
Ratio between DPCCH and DPCH powers in UL
Null column allowed: Yes Default value: 0
INACTIVE_SPREADING_FACT OR_DL
Integer
DL Spreading Factor for inactive users
Null column allowed: Yes Default value: 256
NAME
Text (50)
Bearer name
Null column allowed: No Default value:
PTCH_MAX
Float
For DL part of Bearer: Maximum transmitter power on traffic channel for the bearer not to exceed
Null column allowed: Yes Default value: 21
PTCH_MIN
Float
TYPE
Short
Bearer type (0: Empty, 1: Interactive, 2: Conversational, 3: Background ,4: Streaming)
Null column allowed: Yes Default value: 0
UL_NOMINAL_BIT_RATE
Float
Bearer nominal rate in uplink Unit: kbps
Null column allowed: Yes Default value: 9.6
For DL part of Bearer: Minimum transmitter power on traffic channel for Null column allowed: Yes the bearer not to exceed Default value: -20
2.31 Receivers Table For receiver parameters. Field
Type
Description
Attributes
ADJ_CHANNEL_PROT
Float
Protection against interfering signals from adjacent channels.
Null column allowed: No Default value: 18
ANTENNA
Text (50)
Receiver antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the receiver
Null column allowed: No Default value: 1.5
LOSS
Float
Losses due to receiver radio equipment (up and downlink)
Null column allowed: No Default value: 0
NAME
Text (50)
Receiver name
Null column allowed: No Default value:
2.32 RepeaterEquipments Table For repeater equipment. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
67
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MANUFACTURER
Text (50)
Manufacturer of the repeater equipment
Null column allowed: Yes Default value:
MAX_AMPLIFIER_GAIN
Float
Maximum gain of the amplifier (dB)
Null column allowed: Yes Default value: 90
MAX_OUTPUT_DL
Float
Maximum downlink output power (dBm)
Null column allowed: Yes Default value: 30
MAX_OUTPUT_UL
Float
Maximum uplink output power (dBm)
Null column allowed: Yes Default value: 12
MIN_AMPLIFIER_GAIN
Float
Minimum gain of the amplifier (dB)
Null column allowed: Yes Default value: 50
NAME
Text (50)
Name of the repeater equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Repeater noise Figure (dB)
Null column allowed: Yes Default value: 5
STEP_AMPLIFIER_GAIN
Float
Step of amplifier gain (dB)
Null column allowed: Yes Default value: 1
TIME_DELAY
Float
Time delay in the equipment (microseconds)
Null column allowed: Yes Default value: 5
2.33 Repeaters Table For repeaters. Field
Type
Description
Attributes
AMPLIFIER_GAIN
Float
Gain of the amplifier
Null column allowed: Yes Default value: 80
AZIMUT
Float
Azimuth of the donor side antenna
Null column allowed: Yes Default value: 0
DONOR_CELLID
Text (50)
Name of the donor cell
Null column allowed: No Default value:
DONOR_LINK_LOSS
Float
Loss (dB) between donor and donor side of the repeater
Null column allowed: Yes Default value: 0
DONOR_LINK_TYPE
Short
1- Off air 2- Microwave 3- Fibre
Null column allowed: No Default value: 1
DONOR_PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction between donor and repeater
Null column allowed: Yes Default value:
DOWNTILT
Float
Downtilt of the donor side antenna
Null column allowed: Yes Default value: 0
EQUIPMENT_NAME
Text (50)
If no equipment, the repeater is a passive component
Null column allowed: Yes Default value:
FEEDER_NAME
Text (50)
Name of the donor side feeder
Null column allowed: Yes Default value:
FEEDERLENGTH
Float
Length of donor side feeder
Null column allowed: Yes Default value: 0
HEIGHT
Float
Height of the donor side antenna
Null column allowed: Yes Default value: 25
REC_ANTENNA
Text (50)
Name of the donor side antenna
Null column allowed: Yes Default value:
REC_FEEDERLENGTH_UL
Float
Length of donor side uplink feeder
Null column allowed: Yes Default value: 0
TOTAL_GAIN
Float
Total gain to be applied to donor cell pilot power
Null column allowed: Yes Default value: 0
TOTAL_GAIN_UL
Float
Uplink total gain to be applied to mobile output power
Null column allowed: Yes Default value: 0
68
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
TX_ID
Text (50)
Name of the repeater (and of the transmitter used for coverage)
Null column allowed: No Default value:
Repeater properties are saved in two tables: the donor-side parameters are in the Repeaters table and the coverage-side parameters in the Transmitters table.
2.34 ScramblingCodesDomains Table For names of scrambling code domains. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Resource domain name
Null column allowed: No Default value:
2.35 ScramblingCodesGroups Table For scrambling code groups belonging to scrambling code domains. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Second part of the unique key. Called grouping scheme. Set of scrambling code groups.
Null column allowed: No Default value:
EXCLUDED
Text (225)
List of codes to be excluded from the series defined by FIRST, LAST and STEP (separated by blank characters)
Null column allowed: Yes Default value:
EXTRA
Text (225)
Codes to be added. It is forbidden for EXTRA and EXLUDED to have common numbers. Separator must be a blank character.
Null column allowed: Yes Default value:
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
First part of the unique key. Name of the scrambling code group
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
2.36 Schedulers Table For schedulers. Field
Type
Description
Attributes
NAME
Text (30)
Name of the scheduler
Null column allowed: No Default value:
SCHEDULING_METHOD
Short
0 = Max C/I; 1 = Round-robin; 2 = Proportional Fair
Null column allowed: Yes Default value: 0
2.37 SecondaryAntennas Table For additional antennas. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna installed on the transmitter
Null column allowed: No Default value:
69
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
AZIMUT
Float
Second part of the unique key. Azimuth of the antenna
Null column allowed: No Default value: 0
PERCENT_POWER
Float
Percentage of power dedicated to the secondary antenna
Null column allowed: No Default value: 0
REDT
Float
Remote electrical tilt for secondary antenna
Null column allowed: Yes Default value: 0
TILT
Float
Mechanical downtilt of the secondary antenna
Null column allowed: No Default value: 0
TX_ID
Text (50)
First part of the unique key. Transmitter name
Null column allowed: No Default value:
2.38 Separations Table For scrambling code allocation constraints. Field
Type
Description
Attributes
TX_ID
Text (50)
First part of the unique key. First cell name in a symmetric relation
Null column allowed: No Default value:
TX_ID_OTHER
Text (50)
Second part of the unique key. Second cell name in a symmetric relation
Null column allowed: No Default value:
2.39 ServiceQualityTables Table For release 99 performance graphs. Field
Type
Description
Attributes
DL_QI_TABLE
Memo
QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
QI_NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: No Default value:
SERVICE
Text (50)
Name of the service (can be null for some QI)
Null column allowed: No Default value:
UL_QI_TABLE
Memo
QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
2.40 Sites Table For sites. Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude Unit: m
Null column allowed: Yes Default value:
CDMA_EQUIPMENT
Text (50)
Equipment associated with the site
Null column allowed: Yes Default value:
CHANNEL_ELEMENTS_DL
Integer
Number of available channel elements for downlink
Null column allowed: No Default value: 256
CHANNEL_ELEMENTS_UL
Integer
Number of available channel elements for uplink
Null column allowed: No Default value: 256
COMMENT_
Text (255)
Additional information on the site
Null column allowed: Yes Default value:
70
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
MAX_IUB_RATE_DL
Float
Max Iub Backhaul rate for downlink
Null column allowed: No Default value: 12288
MAX_IUB_RATE_UL
Float
Max Iub Backhaul rate for uplink
Null column allowed: No Default value: 12288
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
2.41 SitesLists Table For sites belonging to site lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list
Null column allowed: No Default value:
SITE_NAME
Text (50)
Second part of the unique key. Name of the site
Null column allowed: No Default value:
2.42 SitesListsNames Table For names of site lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
2.43 TMAEquipments Table For tower-mounted amplifiers. Field
Type
Description
Attributes
DL_LOSSES
Float
Downlink losses of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Tower Mounted Amplifier
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
UL_GAIN
Float
Uplink gain of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
2.44 TplTransmitters Table For station templates. Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value:
71
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
ANTDIVGAIN
Float
Antenna diversity gain Unit: dB
Null column allowed: Yes Default value:
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: No Default value:
AS_THRESHOLD
Float
Max allowed difference with the best-server to enter the Active Set (dB)
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the first antenna
Null column allowed: Yes Default value:
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define each transmitter calculation area Unit: m
Null column allowed: Yes Default value:
CALC_RADIUS2
Integer
Extended calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value:
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CARRIERS
Text (255)
Carriers used by the transmitter
Null column allowed: Yes Default value:
CDMA_EQUIPMENT
Text (50)
CDMA equipment
Null column allowed: Yes Default value:
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value:
CELLS_POWER_SHARING
Boolean
If true, cells' powers are shared for HSDPA users
Null column allowed: No Default value:
CHANNEL_ELEMENTS_DL
Integer
Number of channel elements for downlink
Null column allowed: Yes Default value:
CHANNEL_ELEMENTS_UL
Integer
Number of channel elements for uplink
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value:
DYN_HS_SCCH_POWER_ALL OC
Boolean
Allocation of power for HS-SCCH (True=Dynamic, False=Static)
Null column allowed: No Default value:
DYN_HSDPA_POWER_ALLOC
Boolean
Allocation of power for HSDPA (True=Dynamic, False=Static)
Null column allowed: No Default value:
FBAND
Text (50)
Frequency band
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value:
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value:
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value:
HS_SCCH_POWER
Float
Value of power dedicated to a HS-SCCH channel. In case of dynamic allocation, it is the maximum available power.
Null column allowed: Yes Default value:
HSDPA_MAX_CODES
Short
Maximum number of HS-PDSCH codes
Null column allowed: Yes Default value:
HSDPA_MAX_USERS
Short
Max number of HSDPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value:
72
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
HSDPA_MIN_CODES
Short
Minimum Number of HS-PDSCH codes
Null column allowed: Yes Default value:
HSDPA_PWR
Float
Amount of power (dBm) dedicated to HSDPA
Null column allowed: Yes Default value:
HSDPA_SCHEDULER
Text (50)
HSDPA scheduler
Null column allowed: Yes Default value:
HSPA_SUPPORT
Short
HSPA features supported: 0: None; 1: HSDPA; 2: HSPA; 3: HSPA+
Null column allowed: Yes Default value:
HSUPA_DLPOWER
Float
Amount of power (dBm) dedicated to HSUPA DL chanels (E-AGCH, ERGCH, E-HICH
Null column allowed: Yes Default value:
HSUPA_MAX_USERS
Short
Max number of HSUPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value:
HSUPA_UL_LOAD
Float
Uplink transmitter load factor due to HSUPA users: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
MAX_DL_LOAD
Float
MAX_EXT_NEIGHB_NUMBER
Short
Maximum number of inter-technology neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
MAX_INTERCAR_NEIGHB_NB
Integer
Maximum number of inter-carrier neighbours for this cell
Null column allowed: Yes Default value:
MAX_IUB_RATE_DL
Float
Max Iub Backhaul rate for downlink
Null column allowed: Yes Default value:
MAX_IUB_RATE_UL
Float
Max Iub Backhaul rate for uplink
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Short
Maximum number of neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
MAX_R99BEARER_DL_RATE
Float
Max bearer rate available in DL (kbps)
Null column allowed: Yes Default value:
MAX_R99BEARER_UL_RATE
Float
Max bearer rate available in UL (kbps)
Null column allowed: Yes Default value:
MAX_UL_LOAD
Float
Maximum uplink load allowed (percentage). Used in power control simulation
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
MIMO_SUPPORT
Short
Supported MIMO features: 0 = None; 1 = open loop MIMO; 2 = closed loop MIMO
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous downlink losses
Null column allowed: Yes Default value:
MISCULL
Float
Miscellaneous uplink losses
Null column allowed: Yes Default value:
MULTI_CARRIER
Short
Multi-carrier mode: 0=None; 1=Dual-cell;
Null column allowed: Yes Default value:
NAME
Text (50)
Template name
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value:
NUM_HS_SCCH
Short
Number of HS_SCCH channels
Null column allowed: Yes Default value:
NUM_HSDPA_USERS
Short
Number of served HSDPA users in the cell: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
NUM_HSUPA_USERS
Short
Number of served HSUPA users in the cell: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
NUM_RX_ANTENNAS
Short
Number of transmission antenna ports available at the transmitter
Null column allowed: Yes Default value:
Maximum downlink load allowed (percentage of max power used). Used Null column allowed: Yes in power control simulation Default value:
73
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
NUM_SECTORS
Integer
Number of sectors
Null column allowed: Yes Default value: 3
NUM_TX_ANTENNAS
Short
Number of reception antenna ports available at the transmitter
Null column allowed: Yes Default value:
OTHERS_CCH_POWER
Float
Power of common channels (except SCH)
Null column allowed: Yes Default value:
PILOT_POWER
Float
Power of the pilot channel
Null column allowed: Yes Default value:
POWER_MAX
Float
Maximum power supported by the transmitter
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate predictions
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
PWR_HEADROOM
Float
Power Control Headroom (dB) for DCH (used in WCDMA simulation algorithm)
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value:
REUSE_DIST
Float
Minimum reuse distance for scrambling codes
Null column allowed: Yes Default value:
RSCP_MIN
Float
Minimum RSCP reception level (dBm)
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses in the uplink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
SC_DOMAIN_NAME
Text (50)
Scrambling code domain name
Null column allowed: Yes Default value:
SCH_POWER
Float
Power of the synchronisation (SCH) channel
Null column allowed: Yes Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
TILT
Float
Mechanical downtilt of the main antenna
Null column allowed: Yes Default value:
TMA_NAME
Text (50)
Name of the Tower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TOTAL_POWER
Float
Total downlink power: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
TX_DIVERSITY_CFG
Integer
TX diversity configuration 1- No TX diversity 2- TX div. open loop 3- TX div. closed loop
Null column allowed: Yes Default value:
TX_MAX_POWER
Float
Maximum power sharable between sectors.
Null column allowed: Yes Default value:
TXLOSSES
Float
Losses in the downlink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
UL_LOAD
Float
Uplink transmitter load factor: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UL_REUSE_FACTOR
Float
Uplink (I intra+ I extra)/ I intra: calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value:
2.45 Transmitters Table For transmitters.
74
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value: True
ANTDIVGAIN
Float
Antenna diversity gain
Null column allowed: Yes Default value: 0
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the main antenna
Null column allowed: Yes Default value: 0
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define the calculation area Unit: m
Null column allowed: Yes Default value: 4000
CALC_RADIUS2
Integer
Extended calculation radius
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value: 50
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value: 2000
CELLS_POWER_SHARING
Boolean
If true, cells' powers are shared for HSDPA users
Null column allowed: No Default value: False
COMMENT_
Text (255)
Additional information about the transmitter
Null column allowed: Yes Default value:
DX
Float
X coordinate relative to the site location
Null column allowed: Yes Default value: 0
DY
Float
Y coordinate relative to the site location
Null column allowed: Yes Default value: 0
FBAND
Text (50)
Frequency band
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of feeder in DL
Null column allowed: Yes Default value: 0
FEEDERLENGTH_UL
Float
Length of feeder in UL
Null column allowed: Yes Default value: 0
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value: 25
HEXAGON_GROUP
Text (50)
Group of hexagons used to create this transmitter
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous DL loss
Null column allowed: Yes Default value: 0
MISCULL
Float
Miscellaneous UL loss
Null column allowed: Yes Default value: 0
MULTI_CARRIER
Short
Multi-carrier mode: 0=None; 1=Dual-cell;
Null column allowed: Yes Default value: 0
NOISE_FIGURE
Float
Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
NUM_RX_ANTENNAS
Short
Number of transmission antenna ports available at the transmitter
Null column allowed: No Default value: 1
NUM_TX_ANTENNAS
Short
Number of reception antenna ports available at the transmitter
Null column allowed: No Default value: 1
75
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value: ’Default model’
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value: 0
RXLOSSES
Float
Losses in the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
SITE_NAME
Text (50)
Name of the site on which the transmitter is located (from the Sites table)
Null column allowed: No Default value:
TILT
Float
Mechanical downtilt of the first antenna
Null column allowed: Yes Default value: 0
TMA_NAME
Text (50)
Name of the TMA equipment
Null column allowed: Yes Default value:
TX_DIVERSITY_CFG
Short
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
TX_MAX_POWER
Float
Maximum power sharable between sectors
Null column allowed: Yes Default value: 43
TXLOSSES
Float
Losses in the downlink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
TX diversity configuration: 1=No TX diversity; 2=TX div. open loop; 3=TX Null column allowed: Yes div. closed loop; Default value: 0
2.46 TxsLists Table For transmitters belonging to transmitter lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list.
Null column allowed: No Default value:
TX_NAME
Text (50)
Second part of the unique key. Name of the transmitter.
Null column allowed: No Default value:
2.47 TxsListsNames Table For names of transmitter lists. Field
Type
NAME
Text (50)
Description
Attributes
Name of the transmitter list
Null column allowed: No Default value:
2.48 UECategories Table For HSDPA UE categories.
76
Field
Type
Description
Attributes
MAX_BLOCK_SIZE
Integer
Maximum transport block size supported (bits)
Null column allowed: Yes Default value: 26000
MAX_HSPDSCH_NUM
Short
Maximum number of HS-PDSCH channels for HSDPA
Null column allowed: Yes Default value: 5
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MIMO_SUPPORT
Short
MIMO support: 0=None; 1=MIMO;
Null column allowed: No Default value: 0
MIN_INTERTTI_NUM
Short
Minimum number of TTI between two TTI used
Null column allowed: Yes Default value: 1
MODULATION
Short
Modulation: 0=QPSK; 1=16QAM; 2=64QAM;
Null column allowed: No Default value: 0
MULTI_CARRIER
Short
Multi-carrier mode: 0=None; 1=Dual-cell;
Null column allowed: No Default value: 0
UE_CATEGORY
Short
UE category for HSDPA
Null column allowed: No Default value:
UE_CATEGORY_NAME
Text (50)
Name of the HSDPA UE category
Null column allowed: Yes Default value:
2.49 UERxEquipments Table For names of UE reception equipment. Field
Type
Description
Attributes
NAME
Text (50)
Name of the type of receiver in the UE
Null column allowed: No Default value:
2.50 UMTSEnvironmentDefs Table For traffic environment types. Field
Type
Description
Attributes
DENSITY
Float
Number of subscribers per km2
Null column allowed: Yes Default value: 0
ENVIRONMENT
Text (50)
Environment name
Null column allowed: No Default value:
MOBILITY
Text (50)
Type of mobility
Null column allowed: No Default value:
USER_PROFILE
Text (50)
Type of user profile
Null column allowed: No Default value:
2.51 UMTSMobility Table For mobility types. Field
Type
Description
Attributes
HSSCCH_ECNT
Float
HS-SCCH Ec/Nt target for HSDPA
Null column allowed: Yes Default value: -12
MEAN_SPEED
Float
Mean mobile speed (km/h) used for HSDPA
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of mobility
Null column allowed: No Default value:
TADD
Float
Minimum Ec/Io for best server selection
Null column allowed: No Default value:
2.52 UMTSServices Table For services.
77
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
ADPCH_ACTIVITY
Float
Activity Factor for HSDPA users
Null column allowed: Yes Default value: 0.1
BODY_LOSS
Float
Body loss
Null column allowed: No Default value: 0
CARRIER_LIST
Text (50)
List of preferred carrier numbers
Null column allowed: Yes Default value:
CARRIER_SUPPORT
Integer
Carrier support type: 0=Prefered; 1=Allowed;
Null column allowed: Yes Default value: 0
CPC_SUPPORT
Short
Continuous packet connectivity support: None; DL DRX / UL DTX; HSSCCH Less operation; HS-FACH
Null column allowed: Yes Default value: 0
DL_ACTIVITY
Float
Activity factor for circuit switched service on the downlink
Null column allowed: Yes Default value: 1
DL_DP
Float
Packet inter arrival time (ms) on the downlink
Null column allowed: Yes Default value: 0
DL_DPC
Float
Reading time (distance) between two packet calls (ms) on the downlink
Null column allowed: Yes Default value: 0
DL_GBR
Float
Guaranted downlink bit rate (kbps)
Null column allowed: Yes Default value:
DL_MBR
Float
Maximum downlink bit rate (kbps)
Null column allowed: Yes Default value:
DL_NPC
Integer
Number of packet calls during a session on the downlink
Null column allowed: Yes Default value: 1
DL_PACKET_EFFICIENCY
Float
Packet efficiency factor on the downlink
Null column allowed: Yes Default value:
DL_SP
Integer
Packet size (Bytes) on the downlink
Null column allowed: Yes Default value: 1500
DL_SPC_MAX
Float
Downlink max Packet call size (kBytes)
Null column allowed: Yes Default value: 2000
DL_SPC_MIN
Float
Downlink min Packet call size (kBytes)
Null column allowed: Yes Default value: 4
EDPCH_ACTIVITY
Float
Activity Factor for HSUPA users
Null column allowed: Yes Default value: 0.1
ENABLE_DOWNGRADING
Boolean
Service supports lower bearer than nominal bearer
Null column allowed: No Default value: True
NAME
Text (50)
Service name
Null column allowed: No Default value:
PRIORITY
Integer
Priority level of the service: parameter used in the WCDMA simulation
Null column allowed: Yes Default value: 0
R99BEARER
Text (50)
Name of the R99 Bearer
Null column allowed: Yes Default value:
REQ_AVERAGE_DL_RATE
Float
Requested Average Downlink Rate (kbps)
Null column allowed: Yes Default value:
REQ_AVERAGE_UL_RATE
Float
Requested Average Uplink Rate (kbps)
Null column allowed: Yes Default value:
TH_OFFSET
Float
Offset to add to the above ratio
Null column allowed: No Default value: 0
TH_SCALE_FACTOR
Float
Ratio between application throughput and RLC layer throughput
Null column allowed: No Default value: 95
TYPE
Short
Type of service: 0=circuit; 1=packet; 2=circuit over packet;
Null column allowed: No Default value: 0
UL_ACTIVITY
Float
Activity factor for circuit switched service on the uplink
Null column allowed: Yes Default value: 1
UL_DP
Float
Packet inter arrival time (ms) on the uplink
Null column allowed: Yes Default value: 0
78
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
UL_DPC
Float
Reading time (distance) between two packet calls (ms) on the uplink
Null column allowed: Yes Default value: 0
UL_GBR
Float
Guaranted uplink bit rate (kbps)
Null column allowed: Yes Default value:
UL_MBR
Float
Maximum uplink bit rate (kbps)
Null column allowed: Yes Default value:
UL_NPC
Integer
Number of packet calls during a session on the uplink
Null column allowed: Yes Default value: 1
UL_PACKET_EFFICIENCY
Float
Packet efficiency factor on the uplink
Null column allowed: Yes Default value:
UL_SP
Integer
Packet size (Bytes) on the uplink
Null column allowed: Yes Default value: 1500
UL_SPC_MAX
Float
Uplink max Packet call size (kBytes)
Null column allowed: Yes Default value: 2000
UL_SPC_MIN
Float
Uplink min Packet call size (kBytes)
Null column allowed: Yes Default value: 4
USE_HANDOFF
Boolean
'Yes' if the service supports soft handoff
Null column allowed: No Default value: False
2.53 UMTSServicesQuality Table For release 99 service access thresholds. Field
Type
Description
Attributes
DL_TARGET_QUAL
Float
Eb/Nt target on the downlink for a type of mobility
Null column allowed: Yes Default value: 0
DL_TGT_QUAL_DIVCLOSED
Float
Eb/Nt target on downlink in case of TX diversity closed loop
Null column allowed: Yes Default value: 0
DL_TGT_QUAL_DIVOPEN
Float
Eb/Nt target on downlink in case of TX diversity open loop
Null column allowed: Yes Default value: 0
MOBILITY
Text (50)
Second part of the unique key. Type of mobility
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Type of receiver
Null column allowed: No Default value: “Standard”
SERVICE
Text (50)
First part of the unique key. Name of the R99 Bearer
Null column allowed: No Default value:
UL_TARGET_QUAL
Float
Eb/Nt target on the uplink for a type of mobility
Null column allowed: Yes Default value: 0
UL_TGT_QUAL_DIV2RX
Float
Eb/Nt target on uplink in case of 2RX diversity
Null column allowed: Yes Default value: 0
UL_TGT_QUAL_DIV4RX
Float
Eb/Nt target on uplink in case of 4RX diversity
Null column allowed: Yes Default value: 0
2.54 UMTSServicesUsage Table For user profile parameters. Field
Type
Description
Attributes
CALL_DURATION
Float
Average duration of a call (for circuit switched services) Unit: s
Null column allowed: Yes Default value:
CALL_NUMBER
Float
Average number of calls per hour for circuit switched services or average number of sessions per hour for packet switched services
Null column allowed: Yes Default value: 0
DL_VOLUME
Float
Data volume transferred on the downlink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
79
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
SERVICE
Text (50)
Service that the subscriber can request
Null column allowed: No Default value:
TERMINAL
Text (50)
Type of terminal used by the subscriber for the service
Null column allowed: No Default value:
UL_VOLUME
Float
Data volume transferred on the uplink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
USER_PROFILE
Text (50)
User profile name
Null column allowed: No Default value:
2.55 UMTSTerminals Table For terminals types. Field
Type
Description
Attributes
ACTIVE_SET_SIZE
Short
Maximum number of transmitters possibly connected to the receiver
Null column allowed: No Default value: 3
CPC_SUPPORT
Short
Continuous packet connectivity support: None; DL DRX / UL DTX; HSSCCH Less operation; HS-FACH
Null column allowed: Yes Default value: 0
ENABLE_COMPRESSED_MOD E
Boolean
If true, the mobile connected to a compressed-mode-capable NodeB is able to manage compressed mode when necessary
Null column allowed: No Default value: False
GAIN
Float
Receiver antenna gain
Null column allowed: Yes Default value: 0
HSPA_SUPPORT
Short
HSPA features supported: 0=None; 1=HSDPA; 2=HSPA;
Null column allowed: No Default value: 0
HSUPA_UE_CATEGORY
Short
Category of the User Equipment for HSUPA
Null column allowed: Yes Default value: 1
LOSS
Float
Receiver antenna loss
Null column allowed: Yes Default value: 0
MUD_FACTOR
Float
NAME
Text (50)
Terminal name
Null column allowed: No Default value:
NOISE_FACTOR
Float
Noise figure used to determine the thermal noise at the receiver
Null column allowed: Yes Default value: 8
NOISE_FACTOR_SEC
Float
NOISE_FACTOR_THIRD
Float
Noise figure used to determine the thermal noise at the receiver (for third frequency band)
Null column allowed: Yes Default value: 8
NUM_RX_ANTENNAS
Short
Number of reception antenna ports available at the terminal
Null column allowed: No Default value: 1
PMAX
Float
Maximum receiver power on traffic channel
Null column allowed: Yes Default value: 21
PMIN
Float
Minimum receiver power on traffic channels
Null column allowed: Yes Default value: -20
PRIMARY_BAND
Text (50)
Primary frequency band
Null column allowed: Yes Default value:
RAKE_EFFICIENCY
Float
Efficiency of the rake receiver. Used for combination of Active Set member contributions
Null column allowed: Yes Default value: 1
RHO_FACTOR
Short
Rho factor to model self generated interference
Null column allowed: No Default value: 100
RX_EQUIP
Text (50)
Type of the User Equipment Receiver
Null column allowed: Yes Default value: “Standard”
SECONDARY_BAND
Text (50)
Secondary frequency band
Null column allowed: Yes Default value:
80
Advanced Receiver Factor to model intra-cell interference reduction for Null column allowed: Yes HSDPA terminals only Default value: 0
Noise figure used to determine the thermal noise at the receiver (for the Null column allowed: Yes secondary frequency band) Default value: 8
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
THIRD_BAND
Text (50)
Third frequency band
Null column allowed: Yes Default value:
UE_CATEGORY
Short
Category of the User Equipment for HSDPA
Null column allowed: Yes Default value: 1
2.56 UMTSTraficEnvironments Table For traffic environment clutter weighting. Field
Type
Description
Attributes
CLUTTER_WEIGHTS
Binary
Internal binary format describing weights assigned to each clutter class
Null column allowed: Yes Default value: Yes
NAME
Text (50)
Name of the created environment
Null column allowed: No Default value:
2.57 UMTSUserProfiles Table For names of user profiles. Field
Type
Description
Attributes
NAME
Text (50)
Name of the created user profile
Null column allowed: No Default value:
2.58 Units Table For the reception and transmission units, the projection coordinate system specified in the ATL document, and the database internal coordinate system. Field
Type
Description
Attributes
COORD_SYSTEM
Integer
Display coordinate system when creating database
Null column allowed: Yes Default value: -1
GAIN_UNIT
Integer
Unit used for gains (dBd or dBi) Choice list: 0=dBd; 1=dBi;
Null column allowed: Yes Default value: 0
PROJECTION
Integer
Projected coordinate system for geo data
Null column allowed: Yes Default value: -1
RECEPTION_UNIT
Integer
Reception unit when creating database Choice list: 0=dBm; 1=dbµV; 2=dbµV/m;
Null column allowed: No Default value: 0
TRANSMISSION_UNIT
Integer
Transmission unit when creating database Choice list: 0=dBm; 1=Watts; 2=kWatts;
Null column allowed: No Default value: 0
81
Atoll 3.2.1 Data Structure Reference Guide Chapter 2: UMTS HSPA Data Structure
82
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
3 CDMA2000 Data Structure Atoll supports integrated network planning for CDMA2000, 1xRTT, and 1xEV-DO radio access technologies. This section describes the UMTS HSPA data structure used in Atoll. Figure 3.1 on page 83, Figure 3.2 on page 84, and Figure 3.3 on page 85 depict the structure of the CDMA2000 1xRTT 1xEV-DO database. The following subsections list the tables in the CDMA2000 1xRTT 1xEV-DO database template.
Figure 3.1: CDMA2000 1xRTT 1xEV-DO Template - 1
83
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Figure 3.2: CDMA2000 1xRTT 1xEV-DO Template - 2
84
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Figure 3.3: CDMA2000 1xRTT 1xEV-DO Templates - 3
85
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
3.1 Data Structure Changes Between Atoll 3.1 and 3.2 3.1.1 Added Tables and Fields Antennas Table Field
Type
Description
Attributes
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
CdmaCells Table Field
Type
Description
Attributes
RSCP_MIN
Float
Minimum received signal code power
Null column allowed: Yes Default value: -150
CustomFields Table Field
Type
Description
Attributes
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
FrequencyBands Table Field
Type
Description
Attributes
DELTA_CN
Integer
Logical numeric spacing between two adjacent carrier numbers
Null column allowed: Yes Default value: 1
EXCLUDED_CHANNELS
Text (255)
Excluded carrier numbers
Null column allowed: Yes Default value:
Neighbours Table Field
Type
Description
Attributes
RELATION_TYPE
Short
Neighbour relation type 0=Intra-carrier; 1=Inter-carrier
Null column allowed: Yes Default value:
Field
Type
Description
Attributes
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
Sites Table
TplTransmitters Table Field
Type
Description
Attributes
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
RSCP_MIN
Float
Minimum received signal code power
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
Transmitters Table
86
Field
Type
Description
Attributes
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
UMTSTerminals Table Field
Type
Description
Attributes
NOISE_FACTOR_THIRD
Float
Noise figure of the terminal for the third frequency band
Null column allowed: Yes Default value: 8
THIRD_BAND
Text (50)
Third frequency band supported by the terminal
Null column allowed: Yes Default value:
3.1.2 Deleted Tables and Fields Networks Table • •
DEFAULT_ORTHO_FACTOR AS_PARAMS_IN_CELL
Sites Table •
SUPPORT_NATURE
3.2 Antennas Table For antennas. Field
Type
Description
Attributes
Beamwidth
Float
Antenna beamwidth
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about antenna
Null column allowed: Yes Default value:
CONSTRUCTOR
Text (50)
Antenna manufacturer name
Null column allowed: Yes Default value:
DIAGRAM
Binary
Antenna horizontal and vertical patterns
Null column allowed: Yes Default value:
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
ELECTRICAL_TILT
Float
Antenna electrical tilt
Null column allowed: Yes Default value:
FMax
Double
Maximum operating frequency (MHz) of the antennas
Null column allowed: Yes Default value:
FMin
Double
Minimum operating frequency (MHz) of the antenna
Null column allowed: Yes Default value:
GAIN
Float
Antenna isotropic gain (dBi)
Null column allowed: No Default value: 0
NAME
Text (50)
Name of antenna
Null column allowed: No Default value:
PHYSICAL_ANTENNA
Text (50)
Physical antenna name
Null column allowed: Yes Default value:
The format of the binary field, DIAGRAM, is described in "RF 2D Antenna Pattern Format" on page 275.
3.3 BTSEquipments Table For NodeB equipment.
87
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
CONFIG_DL_LOSSES
Float
Downlink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
CONFIG_UL_LOSSES
Float
Uplink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Base Station Equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Base Station
Null column allowed: Yes Default value: 0
RHO_FACTOR
Short
Rho factor to model self generated interference (100%=ideal)
Null column allowed: Yes Default value: 100
3.4 CarriersType Table For carrier type definition (1xEV-DO or 1xRTT). Field
Type
Description
Attributes
CARRIER
Integer
Carrier number
Null column allowed: No Default value: 0
TYPE
Short
Carrier type
Null column allowed: Yes Default value: 0
3.5 CDMACells Table For cells. Field
Type
Description
Attributes
ACTIVE
Boolean
Cell's activity: True means that the cell is active
Null column allowed: No Default value: True
BCMCS_RATE
Float
BCMCS service rate
Null column allowed: Yes Default value: 204.8
BCMCS_TS_PCT
Float
% of time slots dedicated to Broadcast/MultiCast services
Null column allowed: Yes Default value: 5
CARRIER
Integer
Carrier number
Null column allowed: Yes Default value: 0
CCH_TS_PCT
Float
% of time slots dedicated to Common Control Channels
Null column allowed: Yes Default value: 3
CELL_ID
Text (50)
Name of the cell
Null column allowed: No Default value:
CELL_IDENTITY
Integer
Cell identity
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the cell
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value: 0
DRC_ER_RATE
Float
DRC Erasure Rate (ie % of time DRC values are in error)
Null column allowed: Yes Default value: 25
IDLE_POWER_GAIN
Float
Gain dedicated to transmitted power in idle state.
Null column allowed: Yes Default value: -10
LOCKED_PNO
Boolean
Field used to freeze allocated PNO of the cell during automatic allocation
Null column allowed: No Default value: False
MAX_DL_LOAD
Float
MAX_EVDO_USERS
Integer
88
Maximum downlink load allowed (percentage of max power used). Used Null column allowed: Yes in power control simulation Default value: 50 Maximum number of EV-DO users
Null column allowed: No Default value: 256
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum number of inter-technology neighbours for the cell
Null column allowed: Yes Default value:
MAX_INTERCAR_NEIGHB_NB
Integer
Maximum number of inter-carrier neighbours for this cell
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Integer
Maximum number of neighbours for the cell
Null column allowed: Yes Default value:
MAX_UL_LOAD
Float
Maximum uplink load allowed (percentage). Used in power control simulation
Null column allowed: Yes Default value: 75
MUG_TABLE
Memo
Set of values used to generate the graph MUG=f(number of users)
Null column allowed: Yes Default value:
PAGING_POWER
Float
Power of other common channels except SCH
Null column allowed: Yes Default value: 30
PILOT_POWER
Float
Power of the pilot channel
Null column allowed: Yes Default value: 33
PN_DOMAIN_NAME
Text (50)
PN Offset domain name.
Null column allowed: Yes Default value:
PN_OFFSET
Integer
PN Offset.
Null column allowed: Yes Default value:
POOLED_PWR
Float
Amount of power which can be borrowed in the BTS power pool (dB)
Null column allowed: No Default value: 1
POWER_MAX
Float
Maximum power supported by the transmitter
Null column allowed: Yes Default value: 43
REUSE_DIST
Float
Minimum reuse distance for PN Offsets
Null column allowed: Yes Default value:
ROT_RANGE
Float
Delta of acceptable noise rise (dB)
Null column allowed: Yes Default value: 1
ROT_TARGET
Float
Receiver Noise Rise Over Thermal target (dB)
Null column allowed: Yes Default value: 4
RSCP_MIN
Float
Minimum received signal code power
Null column allowed: Yes Default value: -150
SYNCHRO_POWER
Float
Power of the synchronisation (SCH) channel
Null column allowed: Yes Default value: 23
TADD
Float
Minimum Ec/Io for best server selection
Null column allowed: Yes Default value: -14
TDROP
Float
Ec/Io threshold for active set rejection
Null column allowed: Yes Default value: -17
TOTAL_POWER
Float
Total downlink power: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
TX_ID
Text (50)
Name of the transmitter
Null column allowed: No Default value:
UL_LOAD
Float
Uplink transmitter load factor: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value: 0
3.6 CDMAEquipments Table For site equipment. Field
Type
Description
Attributes
CARRIER_SELECTION
Short
Carrier selection mode Choice list: 0=Min UL noise; 1=Min DL power; 2=Random;3=Sequential;
Null column allowed: No Default value: 0
CE_SHARED_ALL_SECTORS
Boolean
If true CE resources is shared between all sectors of the site
Null column allowed: No Default value: False
89
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
CES_OVERHEAD_DL
Integer
Number of channel elements used for DL overhead channels (pilot, synchro, ...)
Null column allowed: No Default value: 0
CES_OVERHEAD_UL
Integer
Number of channel elements used for UL overhead channels (pilot, synchro, ...)
Null column allowed: No Default value: 0
MANUFACTURER
Text (50)
Name of the manufacturer
Null column allowed: Yes Default value:
MUD_FACTOR
Float
MUD factor for UL interference cancellation
Null column allowed: No Default value: 0
NAME
Text (50)
Equipment name
Null column allowed: No Default value:
RAKE_EFFICIENCY
Float
Efficiency of the rake receiver. Used for combination of AS member contributions
Null column allowed: No Default value: 1
SPP
Boolean
(Sector Power Pooling) If True, sectors' powers available for TCH can be shared among all co-site sectors
Null column allowed: No Default value: False
USE_NEIGHBOURS
Boolean
If true, selection of AS members is limited to the neighbours of the selected transmitter
Null column allowed: No Default value: False
3.7 CDMAEquipmentsCEsUse Table For channel elements consumption in site equipment. Field
Type
Description
Attributes
CHANNEL_ELTS_DL
Float
Number of channel elements used for downlink
Null column allowed: No Default value: 1
CHANNEL_ELTS_UL
Float
Number of channel elements used for uplink
Null column allowed: No Default value: 1
EQUIPMENT
Text (50)
First part of the unique key. Name of equipment
Null column allowed: No Default value:
TERMINAL
Text (50)
Second part of the unique key. Terminal name.
Null column allowed: No Default value:
3.8 CoordSys Table For the projection coordinate system and the database’s internal coordinate system ( this is the display coordinate system used when creating a database).
90
Field
Type
Description
Attributes
CODE
Integer
Identification number of the coordinate system (the code of userdefined coordinate systems is an integer higher than 32768)
Null column allowed: No Default value: 0
DATUM_CODE
Double
DATUM_ROTX
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTY
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTZ
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_SCALE
Double
Parts per million (ppm)
Null column allowed: Yes Default value: 0
DATUM_SHIFTX
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTY
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTZ
Double
Meters
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
ELLIPS_CODE
Integer
ELLIPS_RMAJOR
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_RMINOR
Double
Meters
Null column allowed: Yes Default value: 0
NAME
Text (50)
Coordinate system name
Null column allowed: No Default value:
PROJ_ANGLE
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_FALSE_EASTING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FALSE_NORTHING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FIRST_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LATITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LONGITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_METHOD
Short
UTM, Undefined, NoProjection, Lambert1SP, Lambert2SP, Mercator, CassiniSoldner, TransMercator, TransMercatorSO, ObliqueStereographic, NewZealandMapGrid, HotineOM, LabordeOM, SwissObliqueCylindical
Null column allowed: Yes Default value: 0
PROJ_SCALE_FACTOR
Double
PROJ_SECOND_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_ZONE_NUMBER
Integer
Used with UTM
Null column allowed: Yes Default value: 0
Null column allowed: No Default value: 0
Null column allowed: Yes Default value: 0
3.9 CustomFields Table For defining user-defined fields added to tables, default values for any field (including user-defined fields), and choice lists, captions, and group names for user-defined fields. Field
Type
Description
Attributes
CAPTION
Text (50)
Caption of the field (displayed instead of the name)
Null column allowed: Yes Default value:
CHOICE_LIST
Memo
Choice list for the field
Null column allowed: Yes Default value:
CHOICE_TYPE
Integer
0=Choice list is optional; 1=Choice list is mandatory
Null column allowed: Yes Default value: 0
COLUMN_NAME
Text (50)
Second part of the unique key. Field name
Null column allowed: No Default value:
DEFAULT_VALUE
Text (50)
Default value for the field
Null column allowed: Yes Default value:
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
GROUP_NAME
Text (50)
Name of the group to which that field belongs
Null column allowed: Yes Default value:
TABLE_NAME
Text (50)
First part of the unique key. Table name
Null column allowed: No Default value:
These are some general recommendations that you should follow when handling databases.
91
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
General • • • •
In order to use Atoll with Oracle, you must create Oracle users and schema with names in uppercase. Create backups of the database before upgrading. It is recommended to define a rule for making backups of the database at regular intervals. Do not skip a major Atoll version. For example, if you are currently using Atoll 2.7.xV6.7, you should first upgrade the database to Atoll 2.8.xV6.9 before upgrading to Atoll 3.1.xV7.1. Upgrading your database will be simpler if you do not skip a major version. If you skip or have skipped an intermediate major version, you must upgrade your database twice in order to make it compatible with the new version.
Tables and Fields • •
Table and field names are case sensitive. Table and field names should be not more than 20 characters long. Oracle databases allow a maximum length of 30 characters for field and table names. However, for use in Atoll, you must not create tables and fields with names longer than 20 characters. This is because Atoll adds some characters to the table and field names for certain operations: creating associated triggers, creating project databases, etc. Limiting the length of table and field names to 20 characters will help avoid database connection and consistency problems.
• • • • • •
• •
Table and field names should only use alphanumeric characters (A-Z, a-z, 0-9) and underscores (_). Table and field names must not start with a numeric character (0-9). Table and field names must not contain an SQL or RDBMS-specific keyword, such as ORDER, DATE, etc. Table and field names must not contain spaces or special characters, such as periods (.), exclamation marks (!), colons (:), semi-colons (;), interrogation marks (?), parentheses (()), brackets ({}), square brackets ([]), etc. Boolean fields, system or user-defined, should always have default values assigned. The CustomFields table enables you to define default values, choice lists, and read/write access for any field in any table in Atoll, including user-defined fields that you add to the Atoll tables. The values defined in this table have priority over the internal predefined default values. If you define floating point default values, make sure that all the users have the same decimal separator. If you wish to add custom fields in the Atoll document, you should first add the field in the database, and then update your Atoll document from the database. When setting up your database for the first time, try to anticipate user requirements in terms of custom fields in Atoll tables. Some requirements of the different user groups can be satisfied if a few general-purpose user-defined fields are added in Atoll tables when setting up the database. For example, if you add three user-defined fields (one of type integer, float, and text (limited size)) to the Sites and Transmitters tables, users will be able to use these for sorting, filtering, grouping, or other purposes. This approach can help the database function a long time before users require the addition of other custom fields.
• •
•
To improve performance, if your projects allow it, reduce the size of the fields corresponding to the sites and transmitters’ names. To improve performance, unless absolutely necessary, do not add user-defined fields of Text type. Rather, use numeric field types, which allow sorting and other functions. If you must add Text fields, allocate them the appropriate size that would suffice. For example, a 255-character long Text type field would, for the most part, occupy disk space for no purpose. To improve performance, you should avoid adding custom fields to the neighbour management tables.
3.10 DLBearersSelection Table For downlink bearer selection thresholds.
92
Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of selected bearer
Null column allowed: Yes Default value: 0
CI_REQ
Float
Required Pilot C/I
Null column allowed: Yes Default value:
EARLY_TERM_TABLE
Memo
Tables of Probabilities of Earlier Termination=f(REPEAT_NUM)
Null column allowed: Yes Default value:
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
MODULATION
Short
0=QPSK; 1=8PSK; 2=16QAM; 3=64QAM
Null column allowed: No Default value: 0
NUM_SLOTS
Integer
Number of retransmissions to ensure a correct transmission
Null column allowed: Yes Default value: 1
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: Yes Default value: "Standard"
3.11 DLDORABearers Table For downlink EV-DO Rev. A bearers. Field
Type
Description
Attributes
BEARER_INDEX
Short
EV-DO bearer index
Null column allowed: No Default value:
RLC_PEAK_RATE
Float
RLC bearer rate
Null column allowed: Yes Default value: 0
TRANSPORT_BLOCK_SIZE
Integer
Transport block size (Bits)
Null column allowed: Yes Default value: 0
3.12 DORABearers Table For uplink EV-DO Rev. A bearers. Field
Type
Description
Attributes
BEARER_INDEX
Short
EV-DO bearer index
Null column allowed: No Default value:
RLC_PEAK_RATE
Float
RLC bearer rate
Null column allowed: Yes Default value: 0
TRANSPORT_BLOCK_SIZE
Integer
Transport block size (Bits)
Null column allowed: Yes Default value: 0
3.13 DORABearersProba Table For uplink EV-DO Rev. A bearer probabilities. Field
Type
Description
Attributes
BEARER_INDEX
Short
EV-DO bearer index
Null column allowed: No Default value:
PROBA
Float
Probability of using a bearer
Null column allowed: No Default value: 0
SERVICE
Text (50)
Name of the service
Null column allowed: No Default value:
3.14 DORATerminalT2PRatios Table For uplink traffic to pilot gains. Field
Type
Description
Attributes
AUX_PILOT_GAIN
Float
Auxiliary pilot gain
Null column allowed: Yes Default value:
BEARER_INDEX
Short
EV-DO bearer index
Null column allowed: No Default value: 0
HC_T2P_GAIN
Float
Traffic to pilot gain for High Capacity services
Null column allowed: Yes Default value:
LL_T2P_GAIN
Float
Traffic to pilot gain for Low Latency services
Null column allowed: Yes Default value:
TERMINAL
Text (50)
Terminal name
Null column allowed: No Default value:
93
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
3.15 FeederEquipments Table For feeders. Field
Type
Description
Attributes
CONNECTOR_LOSSES_DL
Float
Feeder connector losses in downlink
Null column allowed: Yes Default value: 0
CONNECTOR_LOSSES_UL
Float
Feeder connector losses in uplink
Null column allowed: Yes Default value: 0
LOSS_PER_METER
Float
Feeder loss per meter
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Feeder
Null column allowed: No Default value:
3.16 FrequencyBands Table For frequency bands. Field
Type
Description
Attributes
BAND_WIDTH
Double
Bandwidth (MHz)
Null column allowed: Yes Default value: 5
DELTA_CN
Integer
Logical numeric spacing between two adjacent carrier numbers
Null column allowed: Yes Default value: 1
EXCLUDED_CHANNELS
Text (255)
Excluded carrier numbers
Null column allowed: Yes Default value:
FIRST_CARRIER
Integer
Number of the first carrier available on the network
Null column allowed: Yes Default value: 0
FREQUENCY
Double
Average frequency of carriers Unit: MHz
Null column allowed: Yes Default value: 2110
LAST_CARRIER
Integer
Number of the last carrier available on the network
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the frequency band
Null column allowed: No Default value:
SPREADING_WIDTH
Double
Spreading bandwidth definition
Null column allowed: Yes Default value: 1.2288
3.17 InterfReductionFactors Table For interference reduction factors between carriers. Field
Type
Description
Attributes
CARRIER1
Integer
First carrier
Null column allowed: No Default value: 0
CARRIER2
Integer
Second carrier
Null column allowed: No Default value: 0
FACTOR
Double
Interference reduction factor
Null column allowed: No Default value: 200
3.18 InterNetChProtect Table For inter-network interference reduction factor graphs.
94
Field
Type
Description
Attributes
ICP
Memo
Inter-network channel protection = f( MHz)
Null column allowed: Yes Default value:
ITF_BW
Double
Interfering bandwidth (kHz)
Null column allowed: No Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
ITF_TECHNO
Text (50)
Interfering technology
Null column allowed: No Default value:
V_BW
Double
Victim bandwidth (kHz)
Null column allowed: No Default value: 0
3.19 Neighbours Table For intra-technology neighbour relations. Field
Type
Description
Attributes
FORCE_HHO
Boolean
Force Handover type to hard handover in case of intra-carriers neighbours
Null column allowed: No Default value: False
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
RELATION_TYPE
Short
Neighbour relation type 0=Intra-carrier; 1=Inter-carrier
Null column allowed: Yes Default value:
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
3.20 NeighboursConstraints Table For intra-technology neighbour allocation constraints. Field
Type
Description
Attributes
FORCE_HHO
Boolean
Force Handover type to hard handover in case of intra-carriers neighbours
Null column allowed: No Default value: False
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
3.21 NeighboursConstraintsExt Table For inter-technology neighbour allocation constraints. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR STATUS
Text (50) Second part of the unique key. List of neighbours from another project. Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: No Default value: Null column allowed: Yes Default value: 0
95
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
3.22 NeighboursExt Table For inter-technology neighbour relations. Field
Type
IMPORTANCE NEIGHBOUR
Float
Description
Attributes
Handover importance (for AFP use)
Null column allowed: Yes Default value: 1
Text (50) Second part of the unique key. List of neighbours from another project
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
3.23 Networks Table For network-level parameters. Field
Type
Description
Attributes
ADD_MRC_SOFTERSOFT
Boolean
If true, gain due to MRC is taken into account for softer/soft cases
Null column allowed: No Default value: False
DEFAULT_HOGAIN_UL
Float
Default soft handoff gain uplink
Null column allowed: No Default value: 0
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: ‘Cost-Hata’
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -130
IOISNTOT
Boolean
Io includes pilot signal or not
Null column allowed: No Default value: True
NAME
Text (50)
NTISNTOT
Boolean
Nt includes pilot signal or not
Null column allowed: No Default value: False
POWERS_RELATIVE_TO_PILO T
Boolean
Cell paging and Synchro powers, Service Allowed DL min and max TCH powers are absolute values or relative to cell pilot power
Null column allowed: No Default value: False
PTOT_RELATIVE_TO_PMAX
Boolean
Cell total power is absolute value (dBm) or relative to Cell maximum power (%)
Null column allowed: No Default value: False
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SPREADING_WIDTH
Float
Spreading width (MHz)
Null column allowed: Yes Default value: 1.2288
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value: ‘1xRTT’
TECHNOLOGY
Text (10)
Name of the technology
Null column allowed: No Default value: ‘CDMA’
96
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
UC_PWC_ON_PILOT
Boolean
True if uplink power control is based on pilot’s target
Null column allowed: No Default value: False
3.24 PnCodesDomains Table For names of PN offset domains. Field
Type
DOMAIN_NAME
Text (50)
Description
Attributes
Resource domain name
Null column allowed: No Default value:
3.25 PnCodesGroups Table For PN offset groups belonging to PN offset domains. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Second part of the unique key. Domain of the PN code group.
Null column allowed: No Default value:
EXCLUDED
Text (225)
List of codes to be excluded from the series defined by FIRST, LAST and STEP (separated by blank character)
Null column allowed: Yes Default value:
EXTRA
Text (225)
Codes to be added. It is forbidden for EXTRA and EXLUDED to have common numbers. Separator must be a blank character.
Null column allowed: Yes Default value:
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
First part of the unique key. Name of the PN code group
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
3.26 PropagationModels Table For propagation models. Field
Type
Description
Attributes
Data
Binary
Model specific parameters
Null column allowed: Yes Default value:
Description
Text (255)
User defined
Null column allowed: Yes Default value:
Name
Text (50)
Name of the propagation model
Null column allowed: No Default value:
Signature
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
Type
Text (50)
ProgID of the model
Null column allowed: No Default value:
3.27 QualityIndicators Table For quality indicators (BER, BLER, etc.).
97
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
CS_QI
Boolean
Flag which indicates if this indicator is used in CS services
Null column allowed: No Default value: True
MEAS_PARAM
Short
Name of the measured figure used for this QI determination Choice list: 1=CPICH_ECIO; 2=CPICH_CI; 3=CPICH_ECNT; 4=DCH_EBNT; 5=HSPDSCH_ECNT;
Null column allowed: Yes Default value: 1
NAME
Text (20)
Name of the managed quality indicator
Null column allowed: No Default value:
PS_QI
Boolean
Flag which indicates if this indicator is used for PS services
Null column allowed: No Default value: True
USE_INTERPOLATION
Boolean
Flag which indicates if this QI must be interpolated or not
Null column allowed: No Default value: True
3.28 Receivers Table For receiver parameters. Field
Type
Description
Attributes
ADJ_CHANNEL_PROT
Float
Protection against interfering signals from adjacent channels.
Null column allowed: No Default value: 18
ANTENNA
Text (50)
Receiver antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the receiver
Null column allowed: No Default value: 1.5
LOSS
Float
Losses due to receiver radio equipment (up and downlink)
Null column allowed: No Default value: 0
NAME
Text (50)
Receiver name
Null column allowed: No Default value:
3.29 RepeaterEquipments Table For repeater equipment.
98
Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
MANUFACTURER
Text (50)
Manufacturer of the repeater equipment
Null column allowed: Yes Default value:
MAX_AMPLIFIER_GAIN
Float
Maximum gain of the amplifier (dB)
Null column allowed: Yes Default value: 90
MAX_OUTPUT_DL
Float
Maximum downlink output power (dBm)
Null column allowed: Yes Default value: 30
MAX_OUTPUT_UL
Float
Maximum uplink output power (dBm)
Null column allowed: Yes Default value: 12
MIN_AMPLIFIER_GAIN
Float
Minimum gain of the amplifier (dB)
Null column allowed: Yes Default value: 50
NAME
Text (50)
Name of the repeater equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Repeater noise Figure (dB)
Null column allowed: Yes Default value: 5
STEP_AMPLIFIER_GAIN
Float
Step of amplifier gain (dB)
Null column allowed: Yes Default value: 1
TIME_DELAY
Float
Time delay in the equipment (microseconds)
Null column allowed: Yes Default value: 5
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
3.30 Repeaters Table For repeaters. Field
Type
Description
Attributes
AMPLIFIER_GAIN
Float
Gain of the amplifier
Null column allowed: Yes Default value: 80
AZIMUT
Float
Azimuth of the donor side antenna
Null column allowed: Yes Default value: 0
DONOR_CELLID
Text (50)
Name of the donor cell
Null column allowed: No Default value:
DONOR_LINK_LOSS
Float
Loss (dB) between donor and donor side of the repeater
Null column allowed: Yes Default value: 0
DONOR_LINK_TYPE
Short
1- Off air 2- Microwave 3- Fibre
Null column allowed: No Default value: 1
DONOR_PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction between donor and repeater
Null column allowed: Yes Default value:
DOWNTILT
Float
Downtilt of the donor side antenna
Null column allowed: Yes Default value: 0
EQUIPMENT_NAME
Text (50)
If no equipment, the repeater is a passive component
Null column allowed: Yes Default value:
FEEDER_NAME
Text (50)
Name of the donor side feeder
Null column allowed: Yes Default value:
FEEDERLENGTH
Float
Length of donor side feeder
Null column allowed: Yes Default value: 0
HEIGHT
Float
Height of the donor side antenna
Null column allowed: Yes Default value: 25
REC_ANTENNA
Text (50)
Name of the donor side antenna
Null column allowed: Yes Default value:
REC_FEEDERLENGTH_UL
Float
Length of donor side uplink feeder
Null column allowed: Yes Default value: 0
TOTAL_GAIN
Float
Total gain to be applied to donor cell pilot power
Null column allowed: Yes Default value: 0
TOTAL_GAIN_UL
Float
Uplink total gain to be applied to mobile output power
Null column allowed: Yes Default value: 0
TX_ID
Text (50)
Name of the repeater (and of the transmitter used for coverage)
Null column allowed: No Default value:
Repeater properties are saved in two tables: the donor-side parameters are in the Repeaters table and the coverage-side parameters in the Transmitters table.
3.31 SecondaryAntennas Table For additional antennas. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna installed on the transmitter
Null column allowed: No Default value:
AZIMUT
Float
Second part of the unique key. Azimuth of the antenna
Null column allowed: No Default value: 0
PERCENT_POWER
Float
Percentage of power dedicated to the secondary antenna
Null column allowed: No Default value: 0
REDT
Float
Remote electrical tilt for secondary antenna
Null column allowed: Yes Default value: 0
99
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
TILT
Float
Mechanical downtilt of the secondary antenna
Null column allowed: No Default value: 0
TX_ID
Text (50)
First part of the unique key. Transmitter name
Null column allowed: No Default value:
3.32 Separations Table For PN offset allocation constraints. Field
Type
Description
Attributes
TX_ID
Text (50)
First part of the unique key. First cell name in a symmetric relation
Null column allowed: No Default value:
TX_ID_OTHER
Text (50)
Second part of the unique key. Second cell name in a symmetric relation
Null column allowed: No Default value:
3.33 ServiceQualityTables Table For 1xRTT performance graphs. Field
Type
Description
Attributes
DL_QI_TABLE
Memo
QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
QI_NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: No Default value: ’Standard’
SERVICE
Text (50)
Name of the service (can be null for some QI)
Null column allowed: No Default value:
UL_QI_TABLE
Memo
QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
3.34 Sites Table For sites. Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude Unit: m
Null column allowed: Yes Default value:
CDMA_EQUIPMENT
Text (50)
Equipment associated with the site
Null column allowed: Yes Default value:
CHANNEL_ELEMENTS_DL
Integer
Number of available channel elements for downlink
Null column allowed: Yes Default value: 256
CHANNEL_ELEMENTS_UL
Integer
Number of available channel elements for uplink
Null column allowed: Yes Default value: 256
COMMENT_
Text (255)
Additional information on the site
Null column allowed: Yes Default value:
EVDO_CES
Integer
Number of EVDO CEs per carrier
Null column allowed: Yes Default value: 96
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
100
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
3.35 SitesLists Table For sites belonging to site lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list
Null column allowed: No Default value:
SITE_NAME
Text (50)
Second part of the unique key. Name of the site
Null column allowed: No Default value:
3.36 SitesListsNames Table For names of site lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
3.37 TMAEquipments Table For tower-mounted amplifiers. Field
Type
Description
Attributes
DL_LOSSES
Float
Downlink losses of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Tower Mounted Amplifier
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
UL_GAIN
Float
Uplink gain of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
3.38 TplTransmitters Table For station templates. Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value:
ANTDIVGAIN
Float
Antenna diversity gain Unit: dB
Null column allowed: Yes Default value:
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: No Default value:
AZIMUT
Float
Azimuth of the first antenna
Null column allowed: Yes Default value:
BCMCS_RATE
Float
BCMCS service rate
Null column allowed: Yes Default value:
101
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
BCMCS_TS_PCT
Float
% of time slots dedicated to Broadcast/MultiCast services
Null column allowed: Yes Default value:
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define each transmitter calculation area Unit: m
Null column allowed: Yes Default value:
CALC_RADIUS2
Integer
Extended calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value:
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CARRIERS
Text (255)
Carriers used by the transmitter
Null column allowed: Yes Default value:
CCH_TS_PCT
Float
% of time slots dedicated to Common Control Channels
Null column allowed: Yes Default value:
CDMA_EQUIPMENT
Text (50)
CDMA equipment
Null column allowed: Yes Default value:
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value:
CHANNEL_ELEMENTS_DL
Integer
Number of channel elements for downlink
Null column allowed: Yes Default value:
CHANNEL_ELEMENTS_UL
Integer
Number of channel elements for uplink
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value:
DRC_ER_RATE
Float
DRC Erasure Rate (ie % of time DRC values are in error)
Null column allowed: Yes Default value:
EVDO_CES
Integer
Number of EVDO channel elements per carrier
Null column allowed: Yes Default value:
FBAND
Text (50)
Frequency band
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value:
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value:
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value:
IDLE_POWER_GAIN
Float
Gain dedicated to transmitted power in idle state
Null column allowed: Yes Default value:
MAX_DL_LOAD
Float
MAX_EVDO_USERS
Integer
Maximum number of EV-DO users
Null column allowed: Yes Default value:
MAX_EXT_NEIGHB_NUMBER
Short
Maximum number of inter-technology neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
MAX_INTERCAR_NEIGHB_NB
Integer
Maximum number of inter-carrier neighbours for this cell
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Short
Maximum number of neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
102
Maximum downlink load allowed (percentage of max power used). Used Null column allowed: Yes in power control simulation Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
MAX_UL_LOAD
Float
Maximum uplink load allowed (percentage). Used in power control simulation
Null column allowed: Yes Default value:
MC_MODE_MUG
Memo
Multi-user gain graph used in multi-carrier mode
Null column allowed: Yes Default value:
MC_MODE_UL_ECNT_MIN
Float
Required Ec/Nt for multi-carrier mode in the uplink
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous downlink losses
Null column allowed: Yes Default value:
MISCULL
Float
Miscellaneous uplink losses
Null column allowed: Yes Default value:
MUG_TABLE
Memo
Set of values used to generate the graph MUG=f(num users)
Null column allowed: Yes Default value:
MULTI_CARRIER
Short
0=None; 1=Multi-Carrier
Null column allowed: Yes Default value:
NAME
Text (50)
Template name
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value:
NUM_SECTORS
Integer
Number of sectors
Null column allowed: Yes Default value: 3
PAGING_POWER
Float
Power of the paging channel
Null column allowed: Yes Default value:
PILOT_POWER
Float
Power of the pilot channel
Null column allowed: Yes Default value:
PN_DOMAIN_NAME
Text (50)
PN Offset code domain name
Null column allowed: Yes Default value:
POOLED_PWR
Float
Amount of power which can be borrowed in the BTS power pool (dB)
Null column allowed: Yes Default value:
POWER_MAX
Float
Maximum power supported by the transmitter
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate predictions
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value:
REUSE_DIST
Float
Minimum reuse distance for PN offsets
Null column allowed: Yes Default value:
ROT_RANGE
Float
Delta of acceptable noise rise (dB)
Null column allowed: Yes Default value:
ROT_TARGET
Float
Receiver Noise Rise Over Thermal target (dB)
Null column allowed: Yes Default value:
RSCP_MIN
Float
Minimum received signal code power
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses in the uplink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
SYNCHRO_POWER
Float
Power of the synchronisation (SCH) channel
Null column allowed: Yes Default value:
103
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
TADD
Float
Minimum Ec/Io for best server selection
Null column allowed: Yes Default value:
TDROP
Float
Ec/Io threshold for active set rejection
Null column allowed: Yes Default value:
TILT
Float
Mechanical downtilt of the main antenna
Null column allowed: Yes Default value:
TMA_NAME
Text (50)
Name of the Tower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TOTAL_POWER
Float
Total downlink power: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
TXLOSSES
Float
Losses in the downlink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
UL_LOAD
Float
Uplink transmitter load factor: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value:
3.39 Transmitters Table For transmitters.
104
Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value: True
ANTDIVGAIN
Float
Antenna diversity gain
Null column allowed: Yes Default value: 0
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the main antenna
Null column allowed: Yes Default value: 0
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define the calculation area Unit: m
Null column allowed: Yes Default value: 4000
CALC_RADIUS2
Integer
Extended calculation radius
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value: 50
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value: 2000
COMMENT_
Text (255)
Additional information about the transmitter
Null column allowed: Yes Default value:
DX
Float
X coordinate relative to the site location
Null column allowed: Yes Default value: 0
DY
Float
Y coordinate relative to the site location
Null column allowed: Yes Default value: 0
FBAND
Text (50)
Frequency band
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of feeder in DL
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
FEEDERLENGTH_UL
Float
Length of feeder in UL
Null column allowed: Yes Default value: 0
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value: 25
HEXAGON_GROUP
Text (50)
Group of hexagons used to create this transmitter
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
MC_MODE_MUG
Memo
Multi-user gain graph used in multi-carrier mode
Null column allowed: Yes Default value:
MC_MODE_UL_ECNT_MIN
Float
Required Ec/Nt for multi-carrier mode in the uplink
Null column allowed: Yes Default value: 0
MISCDLL
Float
Miscellaneous DL loss
Null column allowed: Yes Default value: 0
MISCULL
Float
Miscellaneous UL loss
Null column allowed: Yes Default value: 0
MULTI_CARRIER
Short
0=None; 1=Multi-Carrier
Null column allowed: Yes Default value: 0
NOISE_FIGURE
Float
Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value: ’Default model’
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value: 0
RXLOSSES
Float
Losses in the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
SITE_NAME
Text (50)
Name of the site on which the transmitter is located (from the Sites table)
Null column allowed: No Default value:
TILT
Float
Mechanical downtilt of the first antenna
Null column allowed: Yes Default value: 0
TMA_NAME
Text (50)
Name of the TMA equipment
Null column allowed: Yes Default value:
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
TXLOSSES
Float
Losses in the downlink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
3.40 TxsLists Table For transmitters belonging to transmitter lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list.
Null column allowed: No Default value:
TX_NAME
Text (50)
Second part of the unique key. Name of the transmitter.
Null column allowed: No Default value:
105
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
3.41 TxsListsNames Table For names of transmitter lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the transmitter list
Null column allowed: No Default value:
3.42 UERxEquipments Table For UE reception equipment. Field
Type
Description
Attributes
NAME
Text (50)
Name of the type of receiver in the UE
Null column allowed: No Default value:
3.43 ULBearersSelection Table For uplink bearer selection thresholds. Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of selected bearer
Null column allowed: Yes Default value: 0
EARLY_TERM_TABLE
Memo
Tables of Probabilities of Earlier Termination=f(REPEAT_NUM)
Null column allowed: Yes Default value:
HC_ECNT_REQ
Float
Required Pilot Ec/Nt for High Capacity services
Null column allowed: Yes Default value:
LL_ECNT_REQ
Float
Required Pilot Ec/Nt for Low Latency services
Null column allowed: Yes Default value:
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
MODULATION
Short
0=QPSK; 1=8PSK; 2=16QAM; 3=64QAM
Null column allowed: No Default value: 0
NUM_SUBFRAMES
Integer
Number of retransmissions to ensure a correct transmission
Null column allowed: Yes Default value: 1
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: Yes Default value: "Standard"
3.44 UMTSEnvironmentDefs Table For traffic environment types. Field
Type
Description
Attributes
DENSITY
Float
Number of subscribers per km2
Null column allowed: Yes Default value: 0
ENVIRONMENT
Text (50)
Environment name
Null column allowed: No Default value:
MOBILITY
Text (50)
Type of mobility
Null column allowed: No Default value:
USER_PROFILE
Text (50)
Type of user profile
Null column allowed: No Default value:
3.45 UMTSMobility Table For mobility types.
106
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
COVERI_THROUGHPUTS
Memo
Set of values used to generate the Rate=f(C/I) graph
Null column allowed: Yes Default value: '38.4 -10.5 76.8 -7.5 153.6 -4.5 307.2 -2. 614.4 1 921.6 3.3 1228.8 5 1843.2 9.2 2457.6 11.5'
DELTA_TADD
Float
Delta (dB) to be added to the T_ADD defined in cell’s structure
Null column allowed: Yes Default value: 0
DELTA_TDROP
Float
Delta (dB) to be added to the T_DROP defined in cell’s structure
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of mobility
Null column allowed: No Default value:
UL_ECNT_MIN
Float
Minimum uplink Ec/Nt (EV-DO)
Null column allowed: Yes Default value: -22
3.46 UMTSServices Table For services. Field
Type
Description
Attributes
BODY_LOSS
Float
Body loss
Null column allowed: No Default value: 0
CARRIER
Integer
Carrier supporting the service. -1 means that all carriers can be used.
Null column allowed: No Default value: -1
DLFCH_ACTIVITYFACTOR
Float
Occupancy time of the fundamental channel on the downlink
Null column allowed: Yes Default value: 1
DLRATE_16
Float
Probability to transmit sixteen times the nominal rate on the supplementary channel (SCH) on the downlink
Null column allowed: Yes Default value: 0
DLRATE_2
Float
Probability to transmit twice the nominal rate on the supplementary channel (SCH) on the downlink
Null column allowed: Yes Default value: 0
DLRATE_4
Float
Probability to transmit four times the nominal rate on the supplementary channel (SCH) on the downlink
Null column allowed: Yes Default value: 0
DLRATE_8
Float
Probability to transmit eight times the nominal rate on the supplementary channel (SCH) on the downlink
Null column allowed: Yes Default value: 0
DOWN_153K6_76K8
Float
EV-DO Rev.0 Downgrading probability (153.6 -> 76.8) (Unit 1/255)
Null column allowed: Yes Default value: 0
DOWN_19K2_9K6
Float
EV-DO Rev.0 Downgrading probability (19.2 -> 9.6) (Unit 1/255)
Null column allowed: Yes Default value: 0
DOWN_38K4_19K2
Float
EV-DO Rev.0 Downgrading probability (38.4 -> 19.2) (Unit 1/255)
Null column allowed: Yes Default value: 0
DOWN_76K8_38K4
Float
EV-DO Rev.0 Downgrading probability (76.8 -> 38.4) (Unit 1/255)
Null column allowed: Yes Default value: 0
ENABLE_DOWNGRADING
Boolean
True if downgrading is enabled for the service
Null column allowed: No Default value: True
EVDO_ULRATE_1
Float
Probability to transmit at 9.6 kbps for an EVDO service
Null column allowed: Yes Default value: 0
MIN_RATE_DL
Float
Downlink guaranteed bit rate (kbps)
Null column allowed: Yes Default value: 0
MIN_RATE_UL
Float
Uplink guaranteed bit rate (kbps)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Service name
Null column allowed: No Default value:
PRIORITY
Integer
Priority level of the service: parameter used in the WCDMA simulation
Null column allowed: Yes Default value: 0
QOS_CLASS
Short
0="Best Effort" 1="Guaranteed Bit Rate"
Null column allowed: Yes Default value: 0
107
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
Field
© Forsk 2014
Type
Description
Attributes
TCP_ACK_CURVE
Memo
Table of Reverse Link throughputs=f(Forward Link application layer throughput)
Null column allowed: Yes Default value: '0 0 300 10 600 20 900 30 1200 40 1500 50 1800 60 2400 80'
TCP_SERVICE
Boolean
True if the user application is using TCP
Null column allowed: No Default value: False
TH_OFFSET
Float
Offset to add to the above ratio
Null column allowed: No Default value: 0
TH_SCALE_FACTOR
Float
Ratio between application throughput and RLC layer throughput
Null column allowed: No Default value: 95
TYPE
Short
'0'=’Speech’,’1’=’Data 1xRTT’ ‘2’=’EVDO’
Null column allowed: Yes Default value: 0
UL_OPERATION_MODE
Short
0="High Capacity" 1="Low Latency"
Null column allowed: Yes Default value: 0
ULFCH_ACTIVITYFACTOR
Float
ULRATE_16
Float
Probability to transmit sixteen times the nominal rate on the supplementary channel (SCH) on the uplink
Null column allowed: Yes Default value: 0
ULRATE_2
Float
Probability to transmit twice the nominal rate on the supplementary channel (SCH) on the uplink
Null column allowed: Yes Default value: 0
ULRATE_4
Float
Probability to transmit four times the nominal rate on the supplementary channel (SCH) on the uplink
Null column allowed: Yes Default value: 0
ULRATE_8
Float
Probability to transmit height times the nominal rate on the supplementary channel (SCH) on the uplink
Null column allowed: Yes Default value: 0
UP_19K2_38K4
Float
EV-DO Rev.0 Upgrading probability (19.2 -> 38.4) (Unit 1/255)
Null column allowed: Yes Default value: 0
UP_38K4_76K8
Float
EV-DO Rev.0 Upgrading probability (38.4 -> 76.8) (Unit 1/255)
Null column allowed: Yes Default value: 0
UP_76K8_153K6
Float
EV-DO Rev.0 Upgrading probability (76.8 -> 153.6) (Unit 1/255)
Null column allowed: Yes Default value: 0
UP_9K6_19K2
Float
EV-DO Rev.0 Upgrading probability (9.6 -> 19.2) (Unit 1/255)
Null column allowed: Yes Default value: 0
USE_HANDOFF
Boolean
'Yes' if the service supports soft handoff
Null column allowed: No Default value: False
Either occupancy time of the fundamental channel on the uplink for Null column allowed: Yes 1xRTT, or probability to transmit the nominal rate on the supplementary Default value: 1 channel (SCH) on the uplink in case of 1xEVDO.
3.47 UMTSServicesQuality Table For 1xRTT service access thresholds.
108
Field
Type
Description
Attributes
DL_TARGET_QUAL
Float
Eb/Nt target on the downlink for each type of (mobility, SCH rate) pair
Null column allowed: Yes Default value:
FCH2PILOT
Float
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
PTCH_MAX
Float
Maximum transmitter power on fundamental traffic channel for the service
Null column allowed: Yes Default value: 34
PTCH_MIN
Float
Minimum transmitter power on fundamental traffic channel for the service
Null column allowed: Yes Default value: 14
RX_EQUIP
Text (50)
Type of receiver
Null column allowed: No Default value: ’Standard’
SCH_RATE
Integer
SCH Rate factor (0 -> 16)
Null column allowed: No Default value: 0
FCH power to Pilot power gain. Used if global flag UL_PWC_ON_PILOT is Null column allowed: Yes set to True Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
SCH2PILOT
Float
SERVICE
Text (50)
First part of the unique key. Name of the service
Null column allowed: No Default value:
TERMINAL
Text (50)
Second part of the unique key. Type of terminal
Null column allowed: No Default value:
UL_ECNT_MIN
Float
Pilot’s Ec/Nt target. Used if global flag UL_PWC_ON_PILOT is set to True
Null column allowed: Yes Default value: 0
UL_TARGET_QUAL
Float
Eb/Nt target on the uplink for each type of (mobility, SCH rate) pair
Null column allowed: Yes Default value:
SCH power to Pilot power gain. Used if global flag UL_PWC_ON_PILOT is Null column allowed: Yes set to True Default value: 0
3.48 UMTSServicesUsage Table For user profile parameters. Field
Type
Description
Attributes
CALL_DURATION
Float
Average duration of a call (for circuit switched services) Unit: s
Null column allowed: Yes Default value:
CALL_NUMBER
Float
Average number of calls per hour for circuit switched services or average number of sessions per hour for packet switched services
Null column allowed: Yes Default value: 0
SERVICE
Text (50)
Service that the subscriber can request
Null column allowed: No Default value:
TERMINAL
Text (50)
Type of terminal used by the subscriber for the service
Null column allowed: No Default value:
USER_PROFILE
Text (50)
User profile name
Null column allowed: No Default value:
3.49 UMTSTerminals Table For terminal types. Field
Type
Description
Attributes
ACK_GAIN
Float
ACK gain
Null column allowed: Yes Default value: 4
ACK_GAIN_DORA
Float
ACK gain for 1xEvDo Rev A
Null column allowed: No Default value: 3
ACTIVE_SET_SIZE
Short
DRC_GAIN_NOHO
Float
DRC gain (No handoff case)
Null column allowed: Yes Default value: -1
DRC_GAIN_NOHO_DORA
Float
DRC gain (No handoff case) for 1xEvDo Rev A
Null column allowed: No Default value: -1
DRC_GAIN_SOFT
Float
DRC gain (any kind of soft handoff)
Null column allowed: Yes Default value: -3
DRC_GAIN_SOFT_DORA
Float
DRC gain (any kind of soft handoff) for 1xEvDo Rev A
Null column allowed: No Default value: -3
DRC_GAIN_SOFTER
Float
DRC gain (only softer handoff)
Null column allowed: Yes Default value: -1
DRC_GAIN_SOFTER_DORA
Float
DRC gain (only softer handoff) for 1xEvDo Rev A
Null column allowed: No Default value: -1
FWD_BASEDATARATE
Float
Downlink nominal rate supported by the receiver on the fundamental channel
Null column allowed: No Default value: 9.6
GAIN
Float
Receiver antenna gain
Null column allowed: Yes Default value: 0
Maximum number of transmitters possibly connected with the receiver Null column allowed: Yes for the fundamental channel (FCH) Default value: 6
109
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
© Forsk 2014
Field
Type
Description
Attributes
HANDOFF_TYPE
Short
0=Locked HO; 1=Unlocked HO
Null column allowed: No Default value: 0
LOSS
Float
Receiver antenna loss
Null column allowed: Yes Default value: 0
MODULATION
Short
0=QPSK; 1=8PSK; 2=16QAM; 3=64QAM
Null column allowed: No Default value: 0
NAME
Text (50)
Terminal name
Null column allowed: No Default value:
NOISE_FACTOR
Float
Noise figure used to determine the thermal noise at the receiver
Null column allowed: Yes Default value: 8
NOISE_FACTOR_SEC
Float
Noise figure used to determine the thermal noise at the receiver (for secondary frequency band)
Null column allowed: Yes Default value: 8
NOISE_FACTOR_THIRD
Float
Noise figure of the terminal for the third frequency band
Null column allowed: Yes Default value: 8
NUM_CARRIERS_MAX
Short
Maximum number of carriers supported in multi-carrier mode
Null column allowed: Yes Default value: 3
PILOT_POWER_PCT
Float
Percentage of maximum power dedicated to the UL pilot channel
Null column allowed: Yes Default value: 0
PMAX
Float
Maximum receiver power on traffic channel
Null column allowed: Yes Default value: 23
PMIN
Float
Minimum receiver power on traffic channels
Null column allowed: Yes Default value: -50
PRIMARY_BAND
Text (50)
Primary frequency band
Null column allowed: Yes Default value:
RAKE_EFFICIENCY
Float
Efficiency of the rake receiver. Used for combination of Active Set member contributions
Null column allowed: Yes Default value: 1
RAKE_NUM_FINGERS
Short
Number of links of the active set that will be combined
Null column allowed: Yes Default value: 3
REV_BASEDATARATE
Float
Uplink nominal rate supported by the receiver on the fundamental channel
Null column allowed: No Default value: 9.6
RHO_FACTOR
Short
Rho factor to model self generated interference
Null column allowed: No Default value: 94
RRI_GAIN_DORA
Float
RRI gain for 1xEvDo Rev A
Null column allowed: No Default value: -6
RX_EQUIP
Text (50)
Type of the User Equipment Receiver
Null column allowed: No Default value: ‘Standard’
SCH_AS_SIZE
Short
SECONDARY_BAND
Text (50)
Secondary frequency band
Null column allowed: Yes Default value:
SUPPORTED_TECHNO
Short
0:Speech, 1:1xRTT_Data, 2:1xEvDo_Rel0, 3:1xEvDo_RelA
Null column allowed: No Default value: 0
THIRD_BAND
Text (50)
Third frequency band supported by the terminal
Null column allowed: Yes Default value:
TRAFFIC_GAIN_153_6
Float
Traffic gain (153.6 kbps)
Null column allowed: Yes Default value: 18
TRAFFIC_GAIN_19_2
Float
Traffic gain (19.2 kbps)
Null column allowed: Yes Default value: 7
TRAFFIC_GAIN_38_4
Float
Traffic gain (38.4 kbps)
Null column allowed: Yes Default value: 10
TRAFFIC_GAIN_76_8
Float
Traffic gain (76.8 kbps)
Null column allowed: Yes Default value: 13
TRAFFIC_GAIN_9_6
Float
Traffic gain (9.2 kbps)
Null column allowed: Yes Default value: 4
110
Maximum number of transmitters possibly connected with the receiver Null column allowed: Yes for the supplementary channel (SCH) Default value: 3
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
AT321_DSR_E1
3.50 UMTSTraficEnvironments Table For traffic environment clutter weighting. Field
Type
Description
Attributes
CLUTTER_WEIGHTS
Binary
Internal binary format describing weights assigned to each clutter class
Null column allowed: Yes Default value: Yes
NAME
Text (50)
Name of the created environment
Null column allowed: No Default value:
3.51 UMTSUserProfiles Table For names of user profiles. Field
Type
Description
Attributes
NAME
Text (50)
Name of the created user profile
Null column allowed: No Default value:
3.52 Units Table For the reception and transmission units, the projection coordinate system specified in the ATL document, and the database internal coordinate system. Field
Type
Description
Attributes
COORD_SYSTEM
Integer
Display coordinate system when creating database
Null column allowed: Yes Default value: -1
GAIN_UNIT
Integer
Unit used for gains (dBd or dBi) Choice list: 0=dBd; 1=dBi;
Null column allowed: Yes Default value: 0
PROJECTION
Integer
Projected coordinate system for geo data
Null column allowed: Yes Default value: -1
RECEPTION_UNIT
Integer
Reception unit when creating database Choice list: 0=dBm; 1=dbµV; 2=dbµV/m;
Null column allowed: No Default value: 0
TRANSMISSION_UNIT
Integer
Transmission unit when creating database Choice list: 0=dBm; 1=Watts; 2=kWatts;
Null column allowed: No Default value: 0
111
Atoll 3.2.1 Data Structure Reference Guide Chapter 3: CDMA2000 Data Structure
112
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
4 LTE Data Structure Atoll is a comprehensive framework for operators who need to plan evolution towards LTE and LTE-Advanced. This section describes the UMTS HSPA data structure used in Atoll. Figure 4.1 on page 113, Figure 4.2 on page 114, and Figure 4.3 on page 115 depict the structure of the LTE database. The following subsections list the tables in the LTE database template.
Figure 4.1: LTE Template - 1
113
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Figure 4.2: LTE Template - 2
114
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Figure 4.3: LTE Template - 3
4.1 Data Structure Changes Between Atoll 3.1 and 3.2 4.1.1 Added Tables and Fields Antennas Table Field
Type
Description
Attributes
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
CustomFields Table Field
Type
Description
Attributes
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
FrequencyBands Table Field
Type
Description
Attributes
DELTA_CN
Integer
Step between two adjacent channel numbers
Null column allowed: Yes Default value: 1
115
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
lcchdivgains Table (New) Field
Type
Description
Attributes
EQUIPMENT
Text (50)
Name of the reception equipment to which the control channel diversity gains correspond
Null column allowed: No Default value:
MIMO_RX_ANTENNAS
Short
Number of reception antennas used for MIMO
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of transmission antennas used for MIMO
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
Name of the mobility type to which the control channel diversity gains correspond
Null column allowed: Yes Default value:
PBCH_DIV_GAIN
Float
PBCH diversity gain
Null column allowed: Yes Default value: 0
PDCCH_DIV_GAIN
Float
PDCCH diversity gain
Null column allowed: Yes Default value: 0
lframeconfigs Table Field
Type
Description
Attributes
CELLEDGE_PWR_BOOST
Float
Ratio of the transmission power of cell-edge frequency blocks to cellcentre frequency blocks for Soft FFR and Partial Soft FFR
Null column allowed: Yes Default value:
CYCLIC_PREFIX
Short
Cyclic prefix used by data subframes of a cell
Null column allowed: Yes Default value: 0
ICIC_MODE
Short
The inter-cell interference coordination mode of the configuration: 0 – TD-FFR; 1 – Hard FFR; 2 – Soft FFR; 3 – Partial Soft FFR
Null column allowed: No Default value: 0
PDCCH_SYMBOLS
Short
Number of OFDM symbols per subframe corresponding to the PDCCH
Null column allowed: Yes Default value: 1
PRACH_PREAMBLE_FORMAT
Short
The preamble format for the PRACH
Null column allowed: Yes Default value:
PUCCH_AVG_NRB
Float
Average number of frequency blocks corresponding to the PUCCH
Null column allowed: Yes Default value: 2
llayers Table (New) Field
Type
Description
Attributes
LAYER_INDEX
Short
Index of the network layer
Null column allowed: No Default value: 0
MAX_SPEED
Float
Name of the network layer
Null column allowed: Yes Default value: 300
NAME
Text (50)
Priority of the network layer
Null column allowed: No Default value:
PRIORITY
Short
Maximum speed of mobiles for this layer
Null column allowed: No Default value: 0
SELECTION_MARGIN
Float
Layer selection margin
Null column allowed: Yes Default value: 0
MUGTables Table
116
Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of radio bearer for which the MUG gain is defined
Null column allowed: Yes Default value:
MUG_TABLE_UL
Memo
Uplink multi-user diversity gain table
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Networks Table Field
Type
Description
Attributes
MIMO_INT_PWR_COMB
Short
Whether interfering signals are combined over multiple antennas or not
Null column allowed: Yes Default value: 1
MUMIMO_CRITERION
Short
Radio conditions based on which MU-MIMO is activated or not
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
MAX_S1_RATE_DL
Float
Maximum downlink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
MAX_S1_RATE_UL
Float
Maximum uplink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
Sites Table
T4GBearersRequiredCI Table Field
Type
Description
Attributes
AMS_THRESHOLD
Float
Radio quality required to switch from diversity gains to SU-MIMO throughput gains
Null column allowed: Yes Default value:
MUMIMO_THRESHOLD
Float
Radio quality required to activate MU-MIMO
Null column allowed: Yes Default value:
Field
Type
Description
Attributes
ABS_PATTERN
Text (80)
The pattern of absolute blank subframes with 1=ABS and 0=non-ABS
Null column allowed: Yes Default value:
CELL_TYPE
Short
Type of cell (0 = LTE R8; 1 = LTE R10 PCell; 2 = LTE R10 SCell)
Null column allowed: Yes Default value: 0
DL_MU_SM_GAIN
Float
Downlink MU-MIMO capacity gain
Null column allowed: Yes Default value: 0
P_SCH_ID
Short
Primary Synchronisation Signal ID [0 - 2]
Null column allowed: Yes Default value: 0
PSS_ID_STATUS
Short
PSS ID allocation status (0 = Not allocated, 1 = Allocated, 2 = Locked)
Null column allowed: Yes Default value: 0
S_SCH_ID
Short
Secondary Synchronisation Signal ID [0 - 167]
Null column allowed: Yes Default value: 0
UNIQUE_ID
Text (50)
Unique ID
Null column allowed: Yes Default value:
T4GCells Table
T4GMimoConfigs Table Field
Type
Description
Attributes
MUMIMO_DIV_GAIN
Float
Diversity gain applicable with MU-MIMO
Null column allowed: Yes Default value: 0
SUMIMO_DIV_GAIN
Float
Diversity gain applicable with SU-MIMO
Null column allowed: Yes Default value: 0
T4GServices Table Field
Type
Description
Attributes
MIN_RB_UL
Integer
Minimum number of required frequency blocks for the service
Null column allowed: Yes Default value: 1
117
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
QCI
Short
3GPP QCI (QoS Class Identifier) for the service
Null column allowed: Yes Default value:
SUPPORTED_LAYER_LIST
Text (50)
List of network layers on which the service is allowed
Null column allowed: No Default value: “-1”
T4GTerminals Table Field
Type
Description
Attributes
N_SCELLS_DL
Short
Number of secondary cells in downlink (carrier aggregation)
Null column allowed: Yes Default value: 0
N_SCELLS_UL
Short
Number of secondary cells in uplink (carrier aggregation)
Null column allowed: Yes Default value: 0
SUPPORTED_LAYER_LIST
Text (50)
List of network layers supported by the terminal
Null column allowed: No Default value: “-1”
T4GUECategories Table Field
Type
Description
Attributes
UE_CAT_FOR_DOWNGRADE
Text (50)
Name of the UE category for downgrade from LTE R10 to LTE R8
Null column allowed: Yes Default value:
TplTransmitters Table Field
Type
Description
Attributes
CELL_TYPE
Short
Type of cell (0 = LTE R8; 1 = LTE R10 PCell; 2 = LTE R10 SCell)
Null column allowed: Yes Default value:
LAYER_LIST
Text (255)
List of layers
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
Transmitters Table Field
Type
Description
Attributes
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
4.1.2 Deleted Tables and Fields Sites Table •
SUPPORT_NATURE
4.2 Antennas Table For antennas. Field
118
Type
Description
Attributes
Beamwidth
Float
Antenna beamwidth
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the antenna
Null column allowed: Yes Default value:
CONSTRUCTOR
Text (255)
Antenna manufacturer name
Null column allowed: Yes Default value:
DIAGRAM
Binary
Internal binary format containing the description of the antenna horizontal and vertical patterns
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
ELECTRICAL_TILT
Float
Antenna electrical tilt
Null column allowed: Yes Default value:
FMax
Double
Maximum frequency of created antenna Unit: MHz
Null column allowed: Yes Default value:
FMin
Double
Minimum frequency of created antenna Unit: MHz
Null column allowed: Yes Default value:
GAIN
Float
Antenna isotropic gain Unit: dBi
Null column allowed: No Default value: 0
NAME
Text (50)
Name of antenna created in the current project
Null column allowed: No Default value:
PHYSICAL_ANTENNA
Text (50)
Physical antenna name
Null column allowed: Yes Default value:
The format of the binary field, DIAGRAM, is described in "RF 2D Antenna Pattern Format" on page 275.
4.3 BTSEquipments Table For eNodeB equipment. Field
Type
Description
Attributes
CONFIG_DL_LOSSES
Float
Downlink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
CONFIG_UL_LOSSES
Float
Uplink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Base Station Equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Base Station
Null column allowed: Yes Default value: 0
RHO_FACTOR
Float
Rho factor (not used)
Null column allowed: Yes Default value: 0
4.4 CoordSys Table For the projection coordinate system and the database’s internal coordinate system (this is the display coordinate system used when creating a database). Field
Type
Description
Attributes
CODE
Integer
Identification number of the coordinate system (the code of userdefined coordinate systems is an integer higher than 32768)
Null column allowed: No Default value: 0
DATUM_CODE
Double
DATUM_ROTX
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTY
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTZ
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_SCALE
Double
Parts per million (ppm)
Null column allowed: Yes Default value: 0
DATUM_SHIFTX
Double
Meters
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
119
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DATUM_SHIFTY
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTZ
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_CODE
Integer
ELLIPS_RMAJOR
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_RMINOR
Double
Meters
Null column allowed: Yes Default value: 0
NAME
Text (50)
Coordinate system name
Null column allowed: No Default value:
PROJ_ANGLE
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_FALSE_EASTING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FALSE_NORTHING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FIRST_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LATITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LONGITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_METHOD
Short
UTM, Undefined, NoProjection, Lambert1SP, Lambert2SP, Mercator, CassiniSoldner, TransMercator, TransMercatorSO, ObliqueStereographic, NewZealandMapGrid, HotineOM, LabordeOM, SwissObliqueCylindical
Null column allowed: Yes Default value: 0
PROJ_SCALE_FACTOR
Double
PROJ_SECOND_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_ZONE_NUMBER
Integer
Used with UTM
Null column allowed: Yes Default value: 0
Null column allowed: No Default value: 0
Null column allowed: Yes Default value: 0
4.5 CustomFields Table For defining user-defined fields added to tables, default values for any field (including user-defined fields), and choice lists, captions, and group names for user-defined fields.
120
Field
Type
Description
Attributes
CAPTION
Text (50)
Caption of the field (displayed instead of the name)
Null column allowed: Yes Default value:
CHOICE_LIST
Memo
Choice list for the field
Null column allowed: Yes Default value:
CHOICE_TYPE
Integer
0=Choice list is optional; 1=Choice list is mandatory
Null column allowed: Yes Default value:
COLUMN_NAME
Text (50)
Second part of the unique key. Field name
Null column allowed: No Default value:
DEFAULT_VALUE
Text (50)
Default value for the field
Null column allowed: Yes Default value:
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
GROUP_NAME
Text (50)
Name of the group to which that field belongs
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
TABLE_NAME
Text (50)
First part of the unique key. Table name
Null column allowed: No Default value:
These are some general recommendations that you should follow when handling databases. General • • • •
In order to use Atoll with Oracle, you must create Oracle users and schema with names in uppercase. Create backups of the database before upgrading. It is recommended to define a rule for making backups of the database at regular intervals. Do not skip a major Atoll version. For example, if you are currently using Atoll 2.7.xV6.7, you should first upgrade the database to Atoll 2.8.xV6.9 before upgrading to Atoll 3.1.xV7.1. Upgrading your database will be simpler if you do not skip a major version. If you skip or have skipped an intermediate major version, you must upgrade your database twice in order to make it compatible with the new version.
Tables and Fields • •
Table and field names are case sensitive. Table and field names should be not more than 20 characters long. Oracle databases allow a maximum length of 30 characters for field and table names. However, for use in Atoll, you must not create tables and fields with names longer than 20 characters. This is because Atoll adds some characters to the table and field names for certain operations: creating associated triggers, creating project databases, etc. Limiting the length of table and field names to 20 characters will help avoid database connection and consistency problems.
• • • • • •
• •
Table and field names should only use alphanumeric characters (A-Z, a-z, 0-9) and underscores (_). Table and field names must not start with a numeric character (0-9). Table and field names must not contain an SQL or RDBMS-specific keyword, such as ORDER, DATE, etc. Table and field names must not contain spaces or special characters, such as periods (.), exclamation marks (!), colons (:), semi-colons (;), interrogation marks (?), parentheses (()), brackets ({}), square brackets ([]), etc. Boolean fields, system or user-defined, should always have default values assigned. The CustomFields table enables you to define default values, choice lists, and read/write access for any field in any table in Atoll, including user-defined fields that you add to the Atoll tables. The values defined in this table have priority over the internal predefined default values. If you define floating point default values, make sure that all the users have the same decimal separator. If you wish to add custom fields in the Atoll document, you should first add the field in the database, and then update your Atoll document from the database. When setting up your database for the first time, try to anticipate user requirements in terms of custom fields in Atoll tables. Some requirements of the different user groups can be satisfied if a few general-purpose user-defined fields are added in Atoll tables when setting up the database. For example, if you add three user-defined fields (one of type integer, float, and text (limited size)) to the Sites and Transmitters tables, users will be able to use these for sorting, filtering, grouping, or other purposes. This approach can help the database function a long time before users require the addition of other custom fields.
• •
•
To improve performance, if your projects allow it, reduce the size of the fields corresponding to the sites and transmitters’ names. To improve performance, unless absolutely necessary, do not add user-defined fields of Text type. Rather, use numeric field types, which allow sorting and other functions. If you must add Text fields, allocate them the appropriate size that would suffice. For example, a 255-character long Text type field would, for the most part, occupy disk space for no purpose. To improve performance, you should avoid adding custom fields to the neighbour management tables.
4.6 FeederEquipments Table For feeders. Field
Type
Description
Attributes
CONNECTOR_LOSSES_DL
Float
Feeder connector losses in downlink
Null column allowed: Yes Default value: 0
CONNECTOR_LOSSES_UL
Float
Feeder connector losses in uplink
Null column allowed: Yes Default value: 0
LOSS_PER_METER
Float
Feeder loss per meter
Null column allowed: Yes Default value: 0
121
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
NAME
Text (50)
Name of Feeder
Null column allowed: No Default value:
4.7 FrequencyBands Table For frequency bands. Field
Type
Description
Attributes
ADJ_CHANNEL_PROT
Float
Protection against interfering signals from adjacent channels
Null column allowed: No Default value: 28
CHANNEL_WIDTH
Double
Width of each physical channel composing the frequency band Unit: MHz
Null column allowed: Yes Default value: 5
DELTA_CN
Integer
Step between two adjacent channel numbers
Null column allowed: Yes Default value: 1
DL_FREQUENCY
Double
DL frequency of the 1st channel Unit: MHz
Null column allowed: Yes Default value: 2110
DUPLEXING_METHOD
Short
Duplexing method used in the frequency band Choice list: 0=FDD; 1=TDD;
Null column allowed: No Default value: 0
EXCLUDED_CHANNELS
Text (255)
Physical channels you do not want to allocate
Null column allowed: Yes Default value:
FIRST_CHANNEL
Integer
Number of the first physical channel of the frequency band
Null column allowed: Yes Default value: 0
GUARD_BAND
Float
Guard band between carriers (MHz)
Null column allowed: Yes Default value: 0
LAST_CHANNEL
Integer
Number of the last physical channel of the frequency band
Null column allowed: Yes Default value: 0
N_RB
Integer
Number of resource blocks per channel
Null column allowed: Yes Default value: 25
NAME
Text (50)
Name of the frequency band
Null column allowed: No Default value:
SAMPLING_FREQUENCY
Float
Sampling frequency Unit: MHz
Null column allowed: No Default value: 7.68
UL_FREQUENCY
Double
UL frequency of the 1st channel Unit: MHz
Null column allowed: Yes Default value:
4.8 InterNetChProtect Table For inter-network interference reduction factor graphs. Field
Type
Description
Attributes
ICP
Memo
Inter-network channel protection = f( MHz)
Null column allowed: Yes Default value:
ITF_BW
Double
Interfering bandwidth (kHz)
Null column allowed: No Default value: 0
ITF_TECHNO
Text (50)
Interfering technology
Null column allowed: No Default value:
V_BW
Double
Victim bandwidth (kHz)
Null column allowed: No Default value: 0
4.9 lcchdivgains Table For control channel diversity gains.
122
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
EQUIPMENT
Text (50)
Name of the reception equipment to which the control channel diversity gains correspond
Null column allowed: No Default value:
MIMO_RX_ANTENNAS
Short
Number of reception antennas used for MIMO
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of transmission antennas used for MIMO
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
Name of the mobility type to which the control channel diversity gains correspond
Null column allowed: Yes Default value:
PBCH_DIV_GAIN
Float
PBCH diversity gain
Null column allowed: Yes Default value: 0
PDCCH_DIV_GAIN
Float
PDCCH diversity gain
Null column allowed: Yes Default value: 0
4.10 lframeconfigs Table For frame configurations. Field
Type
Description
Attributes
CELLEDGE_PWR_BOOST
Float
Ratio of the transmission power of cell-edge frequency blocks to cellcentre frequency blocks for Soft FFR and Partial Soft FFR
Null column allowed: Yes Default value:
CYCLIC_PREFIX
Short
Cyclic prefix used by data subframes of a cell
Null column allowed: Yes Default value: 0
ICIC_MODE
Short
The inter-cell interference coordination mode of the configuration: 0 – TD-FFR; 1 – Hard FFR; 2 – Soft FFR; 3 – Partial Soft FFR
Null column allowed: No Default value: 0
N_RB_GROUP0
Text (255)
Frequency blocks belonging to the first group (PSS ID 0)
Null column allowed: Yes Default value:
N_RB_GROUP1
Text (255)
Frequency blocks belonging to the second group (PSS ID 1)
Null column allowed: Yes Default value:
N_RB_GROUP2
Text (255)
Frequency blocks belonging to the third group (PSS ID 2)
Null column allowed: Yes Default value:
N_RB_TOTAL
Short
Number of frequency blocks for which the configuration is defined
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the ICIC frame configuration
Null column allowed: No Default value:
PDCCH_SYMBOLS
Short
Number of OFDM symbols per subframe corresponding to the PDCCH
Null column allowed: Yes Default value: 1
PRACH_PREAMBLE_FORMAT
Short
The preamble format for the PRACH
Null column allowed: Yes Default value:
PUCCH_AVG_NRB
Float
Average number of frequency blocks corresponding to the PUCCH
Null column allowed: Yes Default value: 2
4.11 llayers Table For heterogeneous network (HetNet) deployment layers. Field
Type
Description
Attributes
LAYER_INDEX
Short
Index of the network layer
Null column allowed: No Default value: 0
MAX_SPEED
Float
Name of the network layer
Null column allowed: Yes Default value: 300
NAME
Text (50)
Priority of the network layer
Null column allowed: No Default value:
PRIORITY
Short
Maximum speed of mobiles for this layer
Null column allowed: No Default value: 0
123
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
SELECTION_MARGIN
Float
Layer selection margin
Null column allowed: Yes Default value: 0
4.12 lpcidomains Table For physical cell ID domains. Field
Type
DOMAIN_NAME
Text (50)
Description
Attributes
Name of the physical cell ID domain
Null column allowed: No Default value:
4.13 lpcigroups Table For physical cell ID groups. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Name of the physical cell ID domain
Null column allowed: Default value:
EXCLUDED
Text (225)
List of IDs to be excluded from the series defined by FIRST, LAST and STEP (separated by blank characters)
Null column allowed: Yes Default value:
EXTRA
Text (225)
IDs to be added. It is forbidden for EXTRA and EXLUDED to have common numbers. Separator must be a blank character.
Null column allowed: Yes Default value:
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the physical cell ID group in the domain
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
4.14 MUGTables Table For multi-user diversity gains of proportional fair schedulers. Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of radio bearer for which the MUG gain is defined
Null column allowed: Yes Default value:
MAX_CINR
Float
C/(I+N) above which no MUG will be applied.
Null column allowed: No Default value: 16.8
MOBILITY
Text (50)
Mobility type for which the MUG table is defined.
Null column allowed: No Default value:
MUG_TABLE
Memo
Multi-user diversity gain table
Null column allowed: Yes Default value:
MUG_TABLE_UL
Memo
Uplink multi-user diversity gain table
Null column allowed: Yes Default value:
SCHEDULER_NAME
Text (30)
Name of the scheduler for which the MUG table is defined.
Null column allowed: No Default value:
4.15 Neighbours Table For intra-technology neighbour relations.
124
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Neighbour cell
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
RELATION_TYPE
Short
Type of the neighbour relation: 0=Intra-carrier; 1=Inter-carrier
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
4.16 NeighboursConstraints Table For intra-technology neighbour allocation constraints. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Neighbour cell
Null column allowed: No Default value:
STATUS
Integer
Constraint used in automatic allocation. 0 = Forced; 1 = Forbidden.
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
4.17 NeighboursConstraintsExt Table For inter-technology neighbour allocation constraints. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Neighbour cell or transmitter
Null column allowed: No Default value:
STATUS
Integer
Constraint used in automatic allocation. 0 = Forced; 1 = Forbidden.
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
4.18 NeighboursExt Table For inter-technology neighbour relations. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Neighbour cell
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
125
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
4.19 Networks Table For network-level parameters. Field
Type
Description
Attributes
AMS_SEL_CRITERION
Short
AMS criterion (0 - Reference signal C/N; 1 - Reference signal C/(I+N))
Null column allowed: Yes Default value: 0
BS_SELECTION
Short
Best server selection method: 0=RS C; 1=RSRP;
Null column allowed: Yes Default value: 1
CELL_SELECTION
Short
Serving cell selection method (0 = Obsolete, 1 = Obsolete, 2 = Random, 3 = Layer priority; 4 = Traffic balancing)
Null column allowed: Yes Default value: 3
DEFAULT_CP
Short
Default cyclic prefix Choice list: 0=Normal; 1=Extended;
Null column allowed: Yes Default value: 0
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: "CostHata"
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -20
MIMO_INT_PWR_COMB
Short
Whether interfering signals are combined over multiple antennas or not
Null column allowed: Yes Default value: 1
MUMIMO_CRITERION
Short
Radio conditions based on which MU-MIMO is activated or not
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of network
Null column allowed: No Default value:
PDCCH_SYMBOLS
Short
Number of symbol durations per subframe for PDCCH overhead
Null column allowed: No Default value: 1
POWER_CONTROL_MARGIN
Float
Margin Over Max Bearer Threshold defining C/I Target (dB)
Null column allowed: Yes Default value: 1
PUCCH_AVG_NRB
Float
Average number of overhead resource blocks for PUCCH
Null column allowed: No Default value: 2
RS_EPRE_DEFINITION
Short
RS EPRE Definition Method 0 - Calculated from Max Power, 1 - User Defined
Null column allowed: Yes Default value: 0
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SP_PERIODICITY
Short
Switching point periodicity (TDD) Choice list: 0=Half Frame; 1=Frame;
Null column allowed: Yes Default value: 0
SSF_CONFIG
Short
TDD: Special subframe configuration (0; 1; 2; 3; 4; 5; 6; 7; 8;)
Null column allowed: Yes Default value: 0
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value: ‘LTE’
TECHNOLOGY
Text (10)
Name of the technlogy
Null column allowed: No Default value: ‘OFDM’
THERMAL_NOISE
Float
Thermal noise
Null column allowed: Yes Default value: -121
126
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
4.20 PropagationModels Table For propagation models. Field
Type
Description
Attributes
Data
Binary
Model specific parameters
Null column allowed: Yes Default value:
Description
Text (255)
User defined
Null column allowed: Yes Default value:
Name
Text (50)
Name of the propagation model
Null column allowed: No Default value:
Signature
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
Type
Text (50)
ProgID of the model
Null column allowed: No Default value:
4.21 QualityIndicators Table For quality indicators (BER, BLER, etc.). Field
Type
Description
Attributes
CS_QI
Boolean
Flag indicating whether the Quality Indicator is used for Voice (CS) services
Null column allowed: No Default value: True
MEAS_PARAM
Short
Name of the measured figure used for this QI determination Choice list: 0=C; 1=CIR;
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
PS_QI
Boolean
Flag indicating whether the Quality Indicator is used for Data (PS) services
Null column allowed: No Default value: True
USE_INTERPOLATION
Boolean
Flag indicating whether the Quality Indicator must be interpolated or not
Null column allowed: No Default value: True
4.22 Receivers Table For receiver parameters. Field
Type
Description
Attributes
ANTENNA
Text (50)
Receiver's antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the receiver Unit: m
Null column allowed: No Default value: 1.5
LOSS
Float
Losses due to receiver radio equipment (up and downlink) Unit: dB
Null column allowed: No Default value: 0.
NAME
Text (50)
Name of the receiver
Null column allowed: No Default value:
4.23 RepeaterEquipments Table For repeater equipment. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
MANUFACTURER
Text (50)
Manufacturer of the repeater equipment
Null column allowed: Yes Default value:
MAX_AMPLIFIER_GAIN
Float
Maximum gain of the amplifier (dB)
Null column allowed: Yes Default value: 90
127
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MAX_OUTPUT_DL
Float
Maximum downlink output power (dBm)
Null column allowed: Yes Default value: 30
MAX_OUTPUT_UL
Float
Maximum uplink output power (dBm)
Null column allowed: Yes Default value: 12
MIN_AMPLIFIER_GAIN
Float
Minimum gain of the amplifier (dB)
Null column allowed: Yes Default value: 50
NAME
Text (50)
Name of the repeater equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Repeater noise Figure (dB)
Null column allowed: Yes Default value: 5
STEP_AMPLIFIER_GAIN
Float
Step of amplifier gain (dB)
Null column allowed: Yes Default value: 1
TIME_DELAY
Float
Time delay in the equipment (microseconds)
Null column allowed: Yes Default value: 5
4.24 Repeaters Table For repeaters. Field
Type
Description
Attributes
AMPLIFIER_GAIN
Float
Gain of the amplifier
Null column allowed: Yes Default value: 80
AZIMUT
Float
Azimuth of the donor side antenna
Null column allowed: Yes Default value: 0
DONOR_CELLID
Text (50)
Name of the donor cell
Null column allowed: No Default value:
DONOR_LINK_LOSS
Float
Loss (dB) between donor and donor side of the repeater
Null column allowed: Yes Default value: 0
DONOR_LINK_TYPE
Short
1- Off air 2- Microwave 3- Fibre
Null column allowed: No Default value: 1
DONOR_PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction between donor and repeater
Null column allowed: Yes Default value:
DOWNTILT
Float
Downtilt of the donor side antenna
Null column allowed: Yes Default value: 0
EQUIPMENT_NAME
Text (50)
If no equipment, the repeater is a passive component
Null column allowed: Yes Default value:
FEEDER_NAME
Text (50)
Name of the donor side feeder
Null column allowed: Yes Default value:
FEEDERLENGTH
Float
Length of donor side feeder
Null column allowed: Yes Default value: 0
HEIGHT
Float
Height of the donor side antenna
Null column allowed: Yes Default value: 25
REC_ANTENNA
Text (50)
Name of the donor side antenna
Null column allowed: Yes Default value:
REC_FEEDERLENGTH_UL
Float
Length of donor side uplink feeder
Null column allowed: Yes Default value: 0
TOTAL_GAIN
Float
Total gain to be applied to donor cell pilot power
Null column allowed: Yes Default value: 0
TOTAL_GAIN_UL
Float
Uplink total gain to be applied to mobile output power
Null column allowed: Yes Default value: 0
TX_ID
Text (50)
Name of the repeater (and of the transmitter used for coverage)
Null column allowed: No Default value:
128
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Repeater properties are saved in two tables: the donor-side parameters are in the Repeaters table and the coverage-side parameters in the Transmitters table.
4.25 Schedulers Table For schedulers. Field
Type
Description
Attributes
BEARER_SELECTION
Short
NAME
Text (30)
Name of the scheduler
Null column allowed: No Default value:
SCHEDULING_METHOD
Short
0 = Proportional Fair; 1 = Proportional Demand; 2 = Round Robin; 3 = Max C/I
Null column allowed: Yes Default value: 0
TARGET_THROUGHPUT_DAT A
Short
0 = Peak RLC Throughput; 1 = Effective RLC Throughput; 2 = Application Null column allowed: Yes Throughput Default value: 0
TARGET_THROUGHPUT_VOI CE
Short
0 = Peak RLC Throughput; 1 = Effective RLC Throughput; 2 = Application Null column allowed: Yes Throughput Default value: 0
UL_BW_ALLOCATION
Short
Bearer Selection Criterion: 0 – Bearer Index; 1 – Peak RLC Throughput; 2 Null column allowed: Yes – Effective RLC Throughput Default value: 0
UL Bandwidth Allocation Target: 0 – Full Bandwidth; 1 – Maintain Connection; 2 – Best Bearer
Null column allowed: Yes Default value: 2
4.26 SecondaryAntennas Table For additional antennas. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna installed on the transmitter (from the Antennas table)
Null column allowed: No Default value:
AZIMUT
Float
Azimuth of the antenna
Null column allowed: No Default value: 0
PERCENT_POWER
Float
Percentage of power dedicated to the secondary antenna
Null column allowed: No Default value: 0
REDT
Float
Remote Electrical tilt of the secondary antenna
Null column allowed: Yes Default value: 0
TILT
Float
Mechanical downtilt of the secondary antenna
Null column allowed: No Default value: 0
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
4.27 Sites Table For sites. Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude (user-defined) Unit: m
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the site
Null column allowed: Yes Default value:
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
MAX_S1_RATE_DL
Float
Maximum downlink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
129
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MAX_S1_RATE_UL
Float
Maximum uplink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
4.28 SitesLists Table For sites belonging to site lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list
Null column allowed: No Default value:
SITE_NAME
Text (50)
Second part of the unique key. Name of the site
Null column allowed: No Default value:
4.29 SitesListsNames Table For names of site lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
4.30 SmartAntennas Table For smart antenna equipment. Field
Type
Description
Attributes
BROADCAST_ANTENNA
Text (50)
Broadcast (main) antenna model for the smart antenna
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the Smart Antenna
Null column allowed: No Default value:
SA_MODEL
Text (50)
Smart antenna model used
Null column allowed: Yes Default value:
4.31 SmartAntennasModels Table For smart antenna models.
130
Field
Type
Description
Attributes
SA_DATA
Binary
Smart antenna model data
Null column allowed: Yes Default value:
SA_DESCRIPTION
Text (50)
Description of the smart antenna model
Null column allowed: Yes Default value:
SA_NAME
Text (50)
Name of the smart antenna model
Null column allowed: No Default value:
SA_SIGNATURE
Text (50)
Signature of the smart antenna model
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
SA_TYPE
Text (50)
Type of the smart antenna model
Null column allowed: No Default value:
4.32 T4GBearerQualityCurves Table For bearer performance graphs. Field
Type
Description
Attributes
BEARER_INDEX
Short
Bearer index
Null column allowed: No Default value: 0
MOBILITY
Text (50)
Mobility type
Null column allowed: Yes Default value:
QI_CURVE
Memo
DL Quality QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
QI_NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Name of the reception equipment
Null column allowed: No Default value:
4.33 T4GBearers Table For bearers. Field
Type
Description
Attributes
BEARER_INDEX
Short
Modulation and coding scheme number
Null column allowed: No Default value: 1
CODING_RATE
Float
Coding rate
Null column allowed: Yes Default value: 1
MODULATION
Short
Modulation type Choice list: 0=BPSK; 1=QPSK; 2=16QAM; 3=64QAM;
Null column allowed: No Default value: 1
NAME
Text (50)
Name of the LTE radio bearer
Null column allowed: No Default value:
SPECTRAL_EFFICIENCY
Float
Spectral efficiency = Peak RLC Throughput per Hz Unit: bps/Hz
Null column allowed: Yes Default value: 0
4.34 T4GBearersRequiredCI Table For bearer selection thresholds. Field
Type
Description
Attributes
AMS_THRESHOLD
Float
Radio quality required to switch from diversity gains to SU-MIMO throughput gains
Null column allowed: Yes Default value:
BEARERS_REQUIRED_COVERI
Memo
C/I required in DL for selecting a LTE bearer C/I_Req = f(Best(BEARER_INDEX))
Null column allowed: Yes Default value:
MOBILITY
Text (50)
CPE mobility
Null column allowed: Yes Default value:
MUMIMO_THRESHOLD
Float
Radio quality required to activate MU-MIMO
Null column allowed: Yes Default value:
RX_EQUIP
Text (50)
Name of the reception equipment
Null column allowed: No Default value:
4.35 T4GCells Table For cells.
131
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
ABS_PATTERN
Text (80)
The pattern of absolute blank subframes with 1=ABS and 0=non-ABS
Null column allowed: Yes Default value:
AAS_RESULTS
Binary
Angular distributions of downlink power
Null column allowed: Yes Default value:
AAS_USAGE
Float
Percentage of downlink traffic load carried by the smart antenna
Null column allowed: Yes Default value: 0
ACTIVE
Boolean
Cell's activity. Cell is active if true.
Null column allowed: No Default value: True
AMS_THRESHOLD
Float
C/(I+N) threshold for switching from spatial multiplexing to space-time transmit diversity
Null column allowed: Yes Default value:
CELL_ID
Text (50)
Name of the cell
Null column allowed: No Default value:
CELL_TYPE
Short
Type of cell (0 = LTE R8; 1 = LTE R10 PCell; 2 = LTE R10 SCell)
Null column allowed: Yes Default value: 0
CHANNEL
Integer
Channel number
Null column allowed: Yes Default value: 0
CHANNEL_STATUS
Short
Channel allocation status (0 = Not allocated, 1 = Allocated, 2 = Locked)
Null column allowed: Yes Default value: 0
COMMENT_
Text (255)
Additional information about the cell
Null column allowed: Yes Default value:
DIVERSITY_SUPPORT
Short
The type of antenna diversity supported by the cell in downlink
Null column allowed: Yes Default value: 1
DIVERSITY_SUPPORT_UL
Short
The type of antenna diversity supported by the cell in uplink
Null column allowed: Yes Default value: 1
DL_FFR_USAGE
Float
Percentage of the downlink traffic load carried by the ICIC part of the cell
Null column allowed: Yes Default value: 0
DL_LOAD
Float
Downlink cell traffic load
Null column allowed: Yes Default value: 1
DL_MU_SM_GAIN
Float
Downlink MU-MIMO capacity gain
Null column allowed: Yes Default value: 0
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value: 0
FBAND
Text (50)
Frequency band of the cell
Null column allowed: No Default value:
FRAME_CONFIG
Text (50)
Name of the ICIC frame configuration
Null column allowed: Yes Default value:
ICIC_DELTAPL_TH
Float
Maximum difference in dB between the best server path loss and second best Server path loss to be considered in ICIC zone
Null column allowed: Yes Default value: 0
ICIC_SUPPORT
Short
Inter -Cell Interference Coordination Support 0=None; 1=Static DL; 2=Static UL
Null column allowed: Yes Default value: 0
ID_REUSE_MIN_DIST
Float
The minimum reuse distance for the AFP and physical cell ID allocation
Null column allowed: Yes Default value:
ID_STATUS
Short
SSS ID allocation status (0 = Not allocated, 1 = Allocated, 2 = Locked)
Null column allowed: Yes Default value: 0
MAX_DL_LOAD
Float
Maximum traffic load allowed on downlink
Null column allowed: Yes Default value: 100
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum number of inter-technology neighbours for this cell
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Integer
Maximum number of intra-technology neighbours for this cell
Null column allowed: Yes Default value:
MAX_NUMBER_OF_USERS
Integer
Max supported number of users for the cell
Null column allowed: Yes Default value:
MAX_UL_LOAD
Float
Maximum traffic load allowed on uplink
Null column allowed: Yes Default value: 100
132
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
NOISE_RISE_ICIC_UL
Float
Noise rise received by cell edge traffic
Null column allowed: Yes Default value: 0
NOISE_RISE_UL
Float
Uplink noise rise (dB). Manually specified by the user or calculated during simulations.
Null column allowed: Yes Default value: 0
NUM_DL_USERS
Float
Number of DL connected users for the cell
Null column allowed: Yes Default value: 1
NUM_UL_USERS
Float
Number of UL connected users for the cell
Null column allowed: Yes Default value: 1
P_SCH_ID
Short
Primary Synchronisation Signal ID [0 - 2]
Null column allowed: Yes Default value: 0
PBCH_POWER_OFFSET
Float
EPRE offset for PBCH with respect to RS EPRE
Null column allowed: Yes Default value: 0
PCI_DOMAIN_NAME
Text (50)
Name of the physical cell ID domain
Null column allowed: Yes Default value:
PDCCH_POWER_OFFSET
Float
EPRE offset for PDCCH with respect to RS EPRE
Null column allowed: Yes Default value: 0
PDSCH_POWER_OFFSET
Float
EPRE offset for PDSCH with respect to RS EPRE
Null column allowed: Yes Default value: 0
PHY_CELL_ID
Integer
Physical cell ID
Null column allowed: Yes Default value: 0
POWER
Float
Maximum output power Unit: dBm
Null column allowed: Yes Default value: 43
PSS_ID_STATUS
Short
PSS ID allocation status (0 = Not allocated, 1 = Allocated, 2 = Locked)
Null column allowed: Yes Default value: 0
RANK
Short
Zero based order used by scheduler for sequential cell selection
Null column allowed: Yes Default value:
RS_EPRE
Float
Energy per resource Element of reference signals
Null column allowed: Yes Default value: 0
RSRQ_THRES
Float
Required RSRP for coverage
Null column allowed: Yes Default value: -140
RX_EQUIPMENT
Text (50)
Reception equipment installed at the cell
Null column allowed: Yes Default value:
S_SCH_ID
Short
Secondary Synchronisation Signal ID [0 - 167]
Null column allowed: Yes Default value: 0
SCH_POWER_OFFSET
Float
EPRE offset for SS with respect to RS EPRE
Null column allowed: Yes Default value: 0
SCHEDULER
Text (50)
Scheduler used by the cell
Null column allowed: Yes Default value:
SF_CONFIG
Short
Subframe configuration used by the cell in case of TDD frequency band
Null column allowed: Yes Default value: 1
TX_ID
Text (50)
Name of the transmitter to which the cell belongs
Null column allowed: No Default value:
UL_FPC_CINR_MAX
Float
Target PUSCH C/(I+N) provides Po_pusch and is driven by noise rise limitations of neighbouring cells. This field will be output from simulation.
Null column allowed: Yes Default value: 20
UL_FPC_FACTOR
Float
Factor enabling reduction of transmission powers of cell-edge users FPC Off;0; 0.4;0.5;0.6;0.7;0.8;0.9;1
Null column allowed: No Default value: 1
UL_FPC_NR_MAX
Float
Maximum uplink noise rise
Null column allowed: Yes Default value: 6
UL_LOAD
Float
Uplink cell traffic load
Null column allowed: Yes Default value: 1
UL_MU_SM_GAIN
Float
Multi-user (collaborative) MIMO gain in uplink
Null column allowed: Yes Default value: 0
UNIQUE_ID
Text (50)
Unique ID
Null column allowed: Yes Default value:
133
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value: 0
4.36 T4GEnvironmentDefs Table For traffic environment types. Field
Type
Description
Attributes
DENSITY
Float
Number of subscribers per km2
Null column allowed: Yes Default value: 0
ENVIRONMENT
Text (50)
Environment name
Null column allowed: No Default value:
MOBILITY
Text (50)
Type of mobility
Null column allowed: No Default value:
USER_PROFILE
Text (50)
Type of user profile
Null column allowed: No Default value:
4.37 T4GEquipments Table For reception equipment. Field
Type
Description
Attributes
NAME
Text (50)
Name of the reception equipment
Null column allowed: No Default value:
4.38 T4GMimoConfigs Table For MIMO gain graphs. Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of the LTE bearer
Null column allowed: Yes Default value: 1
EQUIPMENT
Text (50)
Name of the equipment to which the MIMO gains correspond
Null column allowed: No Default value:
MAX_BLER
Float
Maximum value of BLER for which the gains are applicable
Null column allowed: Yes Default value: 1
MAX_MIMO_GAIN
Memo
Graph of maximum MIMO gains vs. C/(I+N)
Null column allowed: Yes Default value:
MIMO_RX_ANTENNAS
Short
Number of MIMO antennas used for reception
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of MIMO antennas used for transmission
Null column allowed: Yes Default value: 1
MOBILITY
Text(50)
User mobility
Null column allowed: Yes Default value:
MUMIMO_DIV_GAIN
Float
Diversity gain applicable with MU-MIMO
Null column allowed: Yes Default value: 0
STTD_GAIN
Float
Diversity gain that will be applied to the CINR (dB)
Null column allowed: Yes Default value: 0
SUMIMO_DIV_GAIN
Float
Diversity gain applicable with SU-MIMO
Null column allowed: Yes Default value: 0
4.39 T4GMobility Table For mobility types.
134
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MEAN_SPEED
Float
Mean mobile speed (km/h) used for HSDPA
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of mobility
Null column allowed: No Default value:
4.40 T4GServices Table For services. Field
Type
Description
Attributes
BODY_LOSS
Float
Losses due to the users body (dB)
Null column allowed: No Default value: 0
DL_ACTIVITY
Float
Activity factor for voice services on the downlink
Null column allowed: Yes Default value: 1
DL_DP
Float
Packet inter-arrival time (ms) in downlink
Null column allowed: Yes Default value: 0
DL_DPC
Float
Reading time (distance) between two packet calls (ms) in downlink
Null column allowed: Yes Default value: 0
DL_GBR
Float
Minimum required transmission rate in DL (Guaranteed Bit Rate)
Null column allowed: No Default value: 0
DL_HIGHEST_BEARER
Float
The highest bearer allowed to be used for this service in DL
Null column allowed: Yes Default value: 15
DL_LOWEST_BEARER
Short
The lowest bearer allowed to be used for this service in DL
Null column allowed: Yes Default value: 1
DL_MBR
Float
Maximum sustained trasmission rate in DL (Maximum Bit Rate)
Null column allowed: No Default value: 0
DL_NPC
Integer
Number of packet calls during a session in downlink
Null column allowed: Yes Default value: 1
DL_SP
Integer
Packet size (Bytes) in downlink
Null column allowed: Yes Default value: 1500
DL_SPC_MAX
Float
Downlink maximum packet call size (kBytes)
Null column allowed: Yes Default value: 2000
DL_SPC_MIN
Float
Downlink minimum packet call size (kBytes)
Null column allowed: Yes Default value: 4
MIN_RB_UL
Integer
Minimum number of required frequency blocks for the service
Null column allowed: Yes Default value: 1
NAME
Text (50)
Service name
Null column allowed: No Default value:
PRIORITY
Short
Service priority (0: lowest)
Null column allowed: Yes Default value: 0
QCI
Short
3GPP QCI (QoS Class Identifier) for the service
Null column allowed: Yes Default value:
REQ_AVERAGE_DL_RATE
Float
Requested Average Downlink Rate (kbps)
Null column allowed: Yes Default value:
REQ_AVERAGE_UL_RATE
Float
Requested Average Uplink Rate (kbps)
Null column allowed: Yes Default value:
SUPPORTED_LAYER_LIST
Text (50)
List of network layers on which the service is allowed
Null column allowed: No Default value: “-1”
TH_OFFSET
Float
Offset to add to TH_SCALE_FACTOR
Null column allowed: No Default value: 0
TH_SCALE_FACTOR
Float
Ratio between application level throughput and RLC layer throughput
Null column allowed: No Default value: 95
TYPE
Short
Service type Choice list: 0=Voice; 1=Data;
Null column allowed: Yes Default value: 0
135
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
UL_ACTIVITY
Float
Activity factor for voice services on the uplink
Null column allowed: Yes Default value: 1
UL_DP
Float
Packet inter-arrival time (ms) in uplink
Null column allowed: Yes Default value: 0
UL_DPC
Float
Reading time (distance) between two packet calls (ms) in uplink
Null column allowed: Yes Default value: 0
UL_GBR
Float
Minimum required transmission rate in UL (Guaranteed Bit Rate)
Null column allowed: No Default value: 0
UL_HIGHEST_BEARER
Float
The highest bearer allowed to be used for this service in UL
Null column allowed: Yes Default value: 15
UL_LOWEST_BEARER
Short
The lowest bearer allowed to be used for this service in UL
Null column allowed: Yes Default value: 1
UL_MBR
Float
Maximum sustained trasmission rate in UL (Maximum Bit Rate)
Null column allowed: No Default value: 0
UL_NPC
Integer
Number of packet calls during a session in uplink
Null column allowed: Yes Default value: 1
UL_SP
Integer
Packet size (Bytes) in uplink
Null column allowed: Yes Default value: 1500
UL_SPC_MAX
Float
Uplink maximum packet call size (kBytes)
Null column allowed: Yes Default value: 2000
UL_SPC_MIN
Float
Uplink minimum packet call size (kBytes)
Null column allowed: Yes Default value: 4
4.41 T4GServicesUsage Table For user profile parameters. Field
Type
Description
Attributes
CALL_DURATION
Float
Average duration of a call (for circuit switched services) Unit: s
Null column allowed: Yes Default value:
CALL_NUMBER
Float
Average number of calls per hour for circuit switched services or average number of sessions per hour for packet switched services
Null column allowed: Yes Default value: 0
DL_VOLUME
Float
Volume transferred on the downlink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
SERVICE
Text (50)
Service (from the Service table) that the subscriber can request
Null column allowed: No Default value:
TERMINAL
Text (50)
Type of terminal (from the Terminal table) used by the subscriber for the service
Null column allowed: No Default value:
UL_VOLUME
Float
Volume transferred on the uplink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
USER_PROFILE
Text (50)
User profile name
Null column allowed: No Default value:
4.42 T4GTerminals Table For terminal types.
136
Field
Type
Description
Attributes
ANTENNA
Text (50)
Receiver's antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
DIVERSITY_SUPPORT
Short
Antenna diversity support (0 = None, 1 = MIMO)
Null column allowed: Yes Default value: 1
GAIN
Float
Terminal antenna gain (dB)
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
LOSS
Float
Terminal antenna loss (dB)
Null column allowed: Yes Default value: 0
MIMO_RX_ANTENNAS
Short
Number of MIMO antennas used for reception
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of MIMO antennas used for transmission
Null column allowed: Yes Default value: 1
N_SCELLS_DL
Short
Number of secondary cells in downlink (carrier aggregation)
Null column allowed: Yes Default value: 0
N_SCELLS_UL
Short
Number of secondary cells in uplink (carrier aggregation)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Terminal name
Null column allowed: No Default value:
NOISE_FACTOR
Float
Noise figure used to determine the thermal noise at the receiver (dB)
Null column allowed: Yes Default value: 8
PMAX
Float
Maximum terminal power on traffic channel (dBm)
Null column allowed: Yes Default value: 23
PMIN
Float
Minimum terminal power on traffic channel (dBm)
Null column allowed: Yes Default value: -40
RX_EQUIP
Text (50)
Name of the reception equipment available at the terminal
Null column allowed: Yes Default value: "Default CPE Reception Equipment"
SUPPORTED_LAYER_LIST
Text (50)
List of network layers supported by the terminal
Null column allowed: No Default value: “-1”
UE_CATEGORY
Text (50)
UE category
Null column allowed: Yes Default value:
4.43 T4GTraficEnvironments Table For traffic environment clutter weighting. Field
Type
Description
Attributes
CLUTTER_WEIGHTS
Binary
Internal binary format describing weights assigned to each clutter class
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the created environment
Null column allowed: No Default value:
4.44 T4GUECategories Table For UE categories. Field
Type
Description
Attributes
BEST_MODULATION
Short
Highest supported modulation in uplink Choice list: 0=QPSK; 1=16QAM; 2=64QAM;
Null column allowed: Yes Default value: 1
DL_TBS_MAX
Float
Maximum number of transport block bits per TTI in downlink
Null column allowed: Yes Default value:
MAX_MIMO_RX_ANTENNAS
Short
Maximum number of reception antenna ports
Null column allowed: Yes Default value: 1
NAME
Text (50)
UE category name
Null column allowed: No Default value:
UE_CAT_FOR_DOWNGRADE
Text (50)
Name of the UE category for downgrade from LTE R10 to LTE R8
Null column allowed: Yes Default value:
UL_TBS_MAX
Float
Maximum number of transport block bits per TTI in uplink
Null column allowed: Yes Default value:
137
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
4.45 T4GUserProfiles Table For names of user profiles. Field
Type
Description
Attributes
NAME
Text (50)
Name of the created user profile
Null column allowed: No Default value:
4.46 TMAEquipments Table For tower-mounted amplifiers. Field
Type
Description
Attributes
DL_LOSSES
Float
Downlink losses of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Tower Mounted Amplifier
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
UL_GAIN
Float
Uplink gain of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
4.47 TplTransmitters Table For station templates.
138
Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value:
AMS_THRESHOLD
Float
CINR threshold in dB to switch from SM to STTD
Null column allowed: Yes Default value:
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter (from the Antennas table)
Null column allowed: No Default value:
AZIMUT
Float
Azimuth of the main antenna
Null column allowed: Yes Default value:
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
CALC_RADIUS2
Integer
Second calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value:
CALC_RESOLUTION2
Integer
Second calculation resolution
Null column allowed: Yes Default value:
CELL_SIZE
Float
Radius of the cell (schematically represented by an hexagon) Unit: m
Null column allowed: Yes Default value:
CELL_TYPE
Short
Type of cell (0 = LTE R8; 1 = LTE R10 PCell; 2 = LTE R10 SCell)
Null column allowed: Yes Default value:
CHANNEL_LIST
Text(255)
Channel numbers used by transmitters
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DIVERSITY_SUPPORT
Short
Type of diversity support used in downlink 0=None, 1=Diversity, 2=SU-MIMO, 3=AMS
Null column allowed: Yes Default value:
Calculation radius used to define each transmitter calculation area Unit: Null column allowed: Yes m Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
DIVERSITY_SUPPORT_UL
Short
Type of diversity support used in uplink 0=None, 1=Diversity, 2=SU-MIMO, 3=AMS, 4=MU-MIMO
Null column allowed: Yes Default value:
DL_FFR_USAGE
Float
Percentage of the downlink traffic load carried by the ICIC part of the cell
Null column allowed: Yes Default value:
DL_LOAD
Float
Downlink traffic load
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value:
FBAND
Text (50)
Frequency band of the cell
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value:
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value:
FRAME_CONFIG
Text (50)
ICIC frame configuration
Null column allowed: Yes Default value:
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value:
ICIC_DELTAPL_TH
Float
Maximum difference in dB between the best server path loss and second best Server path loss to be considered in ICIC zone
Null column allowed: Yes Default value:
ICIC_SUPPORT
Short
Inter -Cell Interference Coordination Support 0=None; 1=Static DL; 2=Static UL
Null column allowed: Yes Default value:
ID_REUSE_MIN_DIST
Float
The minimum reuse distance for the AFP and physical cell ID allocation
Null column allowed: Yes Default value:
LAYER_LIST
Text (255)
List of layers
Null column allowed: Yes Default value:
MAX_DL_LOAD
Float
Maximum traffic load allowed on downlink
Null column allowed: Yes Default value:
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum number of inter-technology neighbours
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Integer
Maximum number of intra-technology neighbours
Null column allowed: Yes Default value:
MAX_NUMBER_OF_USERS
Integer
Max supported number of users for the cell
Null column allowed: Yes Default value:
MAX_UL_LOAD
Float
Maximum traffic load allowed on uplink
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous downlink loss
Null column allowed: Yes Default value:
MISCULL
Float
Miscellaneous uplink loss
Null column allowed: Yes Default value:
NAME
Text (50)
Template name
Null column allowed: No Default value:
NOISE_FIGURE
Float
Total Noise figure used to determine the thermal noise at the transmitter (Temp)
Null column allowed: Yes Default value:
NOISE_RISE_ICIC_UL
Float
Noise rise received by cell edge traffic
Null column allowed: Yes Default value:
NOISE_RISE_UL
Float
Uplink interference noise rise (dB)
Null column allowed: Yes Default value:
NUM_SECTORS
Integer
Number of sectors
Null column allowed: No Default value:
PBCH_POWER_OFFSET
Float
EPRE offset for PBCH with respect to RS EPRE
Null column allowed: Yes Default value:
139
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
PCI_DOMAIN_NAME
Text (50)
Name of the physical cell ID domain
Null column allowed: Yes Default value:
PDCCH_POWER_OFFSET
Float
EPRE offset for PDCCH with respect to RS EPRE
Null column allowed: Yes Default value:
PDSCH_POWER_OFFSET
Float
EPRE offset for PDSCH with respect to RS EPRE
Null column allowed: Yes Default value:
PHY_CELLID_LIST
Text(255)
Physical cell IDs used by transmitters
Null column allowed: Yes Default value:
POWER
Float
Maximum cell output power (dBm)
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (255)
Name of the second propagation model used to calculate prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value:
RS_EPRE
Float
Energy per resource Element of reference signals
Null column allowed: Yes Default value:
RSRQ_THRES
Float
Required RSRP for coverage
Null column allowed: Yes Default value:
RX_ANTENNAS_PORTS
Short
Number of reception antenna ports
Null column allowed: Yes Default value:
RX_EQUIPMENT
Text (50)
Reception equipment
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
SA_NAME
Text (50)
Name of the smart antenna equipment
Null column allowed: Yes Default value:
SCH_POWER_OFFSET
Float
EPRE offset for SS with respect to RS EPRE
Null column allowed: Yes Default value:
SCHEDULER
Text (30)
Scheduler used by the cell
Null column allowed: Yes Default value:
SF_CONFIG
Short
Subframe configuration used by the cell in case of TDD frequency band
Null column allowed: Yes Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
TILT
Float
Mechanical downtilt of the main antenna
Null column allowed: Yes Default value:
TMA_NAME
Text (50)
Name of the Tower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TX_ANTENNAS_PORTS
Short
Number of transmission antenna ports
Null column allowed: Yes Default value:
TX_TYPE
Short
Type of transmitter (0 = Normal; 1 = Interferer only)
Null column allowed: Yes Default value:
TXLOSSES
Float
Losses on the downlink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
UL_FPC_CINR_MAX
Float
Target PUSCH C/(I+N) provides Po_pusch and is driven by noise rise limitations of neighbouring cells. This field will be output from simulation.
Null column allowed: Yes Default value:
UL_FPC_FACTOR
Float
Factor enabling reduction of transmission powers of cell-edge users 0;0.4;0.5;0.6;0.7;0.8;0.9;1
Null column allowed: Yes Default value:
UL_FPC_NR_MAX
Float
Maximum uplink noise rise
Null column allowed: Yes Default value:
140
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
UL_LOAD
Float
Uplink traffic load
Null column allowed: Yes Default value:
UL_MU_SM_GAIN
Float
Multi-user (collaborative) MIMO gain in uplink
Null column allowed: Yes Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value:
4.48 Transmitters Table For transmitters. Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value: True
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter (from the Antennas table)
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the first antenna
Null column allowed: Yes Default value: 0
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define the calculation area Unit: m
Null column allowed: Yes Default value: 4000
CALC_RADIUS2
Integer
Second calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value: 50
CALC_RESOLUTION2
Integer
Second calculation resolution
Null column allowed: Yes Default value:
CELL_SIZE
Float
Radius of the cell (schematically represented by an hexagon)
Null column allowed: Yes Default value: 2000
COMMENT_
Text (255)
Additional information about the transmitter
Null column allowed: Yes Default value:
DX
Float
X coordinate relative to the site position
Null column allowed: Yes Default value: 0
DY
Float
Y coordinate relative to the site position
Null column allowed: Yes Default value: 0
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value: 0
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value: 0
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value: 25
HEXAGON_GROUP
Text (50)
Group of hexagons which contains this transmitter
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous downlink loss
Null column allowed: Yes Default value: 0
MISCULL
Float
Miscellaneous uplink loss
Null column allowed: Yes Default value: 0
NOISE_FIGURE
Float
Total Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
POLARIZATION
Text (1)
Polarization of the antennas installed at the transmitter
Null column allowed: Yes Default value: "V"
141
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
© Forsk 2014
Field
Type
Description
Attributes
PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (50)
Name of the second propagation model used to calculate prediction
Null column allowed: Yes Default value:
REDT
Float
Remote electrical tilt of the main antenna
Null column allowed: Yes Default value: 0
RX_ANTENNAS_PORTS
Short
Number of antenna ports in reception
Null column allowed: Yes Default value: 1
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
SA_NAME
Text (50)
Name of the smart antenna equipment
Null column allowed: Yes Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
SITE_NAME
Text (50)
Name of the site at which the transmitter is located (from the Sites table)
Null column allowed: No Default value:
TILT
Float
Mechanical downtilt of the first antenna
Null column allowed: Yes Default value: 0
TMA_NAME
Text (50)
Name of theTower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TX_ANTENNAS_PORTS
Short
Number of antenna ports in transmission
Null column allowed: Yes Default value: 1
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
TX_TYPE
Short
Type of transmitter (0 = Normal; 1 = Interferer only)
Null column allowed: Yes Default value: 0
TXLOSSES
Float
Losses on the downlink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
4.49 TxsLists Table For transmitters belonging to transmitter lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list.
Null column allowed: No Default value:
TX_NAME
Text (50)
Second part of the unique key. Name of the transmitter.
Null column allowed: No Default value:
4.50 TxsListsNames Table For names of transmitter lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the transmitter list
Null column allowed: No Default value:
4.51 Units Table For the reception and transmission units, the projection coordinate system specified in the ATL document, and the database internal coordinate system.
142
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
COORD_SYSTEM
Integer
Display coordinate system when creating database
Null column allowed: Yes Default value: -1
GAIN_UNIT
Integer
Unit used for gains (dBd or dBi) Choice list: 0=dBd; 1= dBi;
Null column allowed: Yes Default value: 0
PROJECTION
Integer
Projected coordinate system for geo data
Null column allowed: Yes Default value: -1
RECEPTION_UNIT
Integer
Reception unit when creating database Choice list: 0=dBm; 1=dbµV; 2=dbµV/m;
Null column allowed: No Default value: 0
TRANSMISSION_UNIT
Integer
Transmission unit when creating database Choice list: 0=dBm; 1=Watts; 2=kWatts;
Null column allowed: No Default value: 0
143
Atoll 3.2.1 Data Structure Reference Guide Chapter 4: LTE Data Structure
144
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5 3GPP Multi-RAT Data Structure 3GPP Multi-RAT Atoll documents can contain one, two, or all 3GPP technologies: GSM, UMTS, and LTE. Tables in the 3GPP Multi-RAT template include the following categories of tables: •
"Tables Common to All Technologies" on page 145 These tables are shared and used by all the technologies. There structures (fields, keys, and relations with other tables) are similar to the structures of these tables in single-technology documents. The multi-RAT traffic model allows you to define services, terminals, and mobility types, user profiles, and traffic environments for all three technologies. These tables have a multi-level definition: a technology-independent level and a technology-specific level.
• • •
"GSM-specific Tables" on page 151 "UMTS-specific Tables" on page 156 "LTE-specific Tables" on page 161 These tables are specific to technologies. There structures are the same as in single-technology documents.
5.1 Tables Common to All Technologies 5.1.1 Data Structure Changes Between Atoll 3.1 and 3.2 5.1.1.1 Added Tables and Fields antennas Table Field
Type
Description
Attributes
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
customfields Table Field
Type
Description
Attributes
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
networks Table Field
Type
Description
Attributes
MIMO_INT_PWR_COMB
Short
Whether interfering signals are combined over multiple antennas or not
Null column allowed: Yes Default value: 1
MUMIMO_CRITERION
Short
Radio conditions based on which MU-MIMO is activated or not
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
MAX_S1_RATE_DL
Float
Maximum downlink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
MAX_S1_RATE_UL
Float
Maximum uplink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
sites Table
5.1.1.2 Deleted Tables and Fields networks Table •
DEFAULT_ORTHO_FACTOR
145
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
sites Table •
SUPPORT_NATURE
5.1.2 antennas Table For the table description, see "Antennas Table" on page 118.
5.1.3 btsequipments Table For the table description, see "BTSEquipments Table" on page 119.
5.1.4 coordsys Table For the table description, see "CoordSys Table" on page 119.
5.1.5 customfields Table For the table description, see "CustomFields Table" on page 120.
5.1.6 environmentdefs Table For the table description, see "T4GEnvironmentDefs Table" on page 134.
5.1.7 feederequipments Table For the table description, see "FeederEquipments Table" on page 121.
5.1.8 internetchprotect Table For the table description, see "InterNetChProtect Table" on page 122. This table contains the following additional field in the 3GPP multi-RAT template: Field
Type
Description
Attributes
V_TECHNO
Text (50)
Victim technology
Null column allowed: No Default value:
5.1.9 mobility Table Figure 5.1 on page 146, shows the multi-level definition of the multi-RAT mobility types model tables.
Figure 5.1: 3GPP Mobility Types Model
146
Field
Type
Description
Attributes
NAME
Text (50)
Name of mobility type
Null column allowed: No Default value:
MEAN_SPEED
Float
Average speed (km/h)
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.1.10 networks Table The networks table contains one record for each technology in the document. In each record, only parameters relevant for the row’s technology are used. Field
Type
Description
Attributes
ADD_MRC_SOFTERSOFT
Boolean
If true, gain due to MRC is taken into account for softer/soft cases
Null column allowed: No Default value: False
AMS_SEL_CRITERION
Short
AMS criterion (0 - Reference signal C/N; 1 - Reference signal C/(I+N))
Null column allowed: Yes Default value: 0
BS_SELECTION
Short
Best server selection method: 0=RS C; 1=RSRP;
Null column allowed: Yes Default value: 0
CELL_SELECTION
Short
Serving cell selection method (0 = Min DL Load, 1 = Min UL Load, 2 = Random, 3 = Sequential)
Null column allowed: Yes Default value: 2
COMPRESSED_DELTA_DL_Q UAL
Float
Eb/Nt DL target overhead due to compressed mode activated
Null column allowed: No Default value: 1
COMPRESSED_DELTA_UL_Q UAL
Float
Eb/Nt UL target overhead due to compressed mode activated
Null column allowed: No Default value: 1
COMPRESSED_ON_ECIO
Boolean
Compressed mode activated on Ec/Io threshold
Null column allowed: No Default value: True
COMPRESSED_ON_RSCP
Boolean
Compressed mode activated on RSCP threshold
Null column allowed: No Default value: False
COMPRESSED_THRESHOLD
Float
Ec/Io threshold for compressed mode activation
Null column allowed: No Default value: -13
CQI_CPICH_BASED
Boolean
CQI determination ids based on CPICH quality (true) or on HS-PDSCH quality (false)
Null column allowed: No Default value: True
DEFAULT_CP
Short
Default cyclic prefix Choice list: 0=Normal; 1=Extended;
Null column allowed: Yes Default value: 0
DEFAULT_HOGAIN_UL
Float
Default soft handoff gain uplink
Null column allowed: No Default value: 0
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: "CostHata"
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
HSDPA_NTISNTOT
Boolean
Nt includes or not pilot's signal for HS-SCCH, HS-PDSCH and CPICH for CQI determination
Null column allowed: No Default value: False
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -130
IOISNTOT
Boolean
Io includes pilot signal or not
Null column allowed: No Default value: True
MIMO_INT_PWR_COMB
Short
Whether interfering signals are combined over multiple antennas or not
Null column allowed: Yes Default value: 1
MUMIMO_CRITERION
Short
Radio conditions based on which MU-MIMO is activated or not
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of network
Null column allowed: No Default value:
NTISNTOT
Boolean
Nt includes pilot signal or not
Null column allowed: No Default value: False
PDCCH_SYMBOLS
Short
Number of symbol durations per subframe for PDCCH overhead
Null column allowed: No Default value: 1
POWER_CONTROL_MARGIN
Float
Margin Over Max Bearer Threshold defining C/I Target (dB)
Null column allowed: Yes Default value: 1
POWERS_RELATIVE_TO_PILO T
Boolean
Cell paging and Synchro powers, Service Allowed DL min and max TCH powers are absolute values or relative to cell pilot power
Null column allowed: No Default value: False
147
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
Field
Type
Description
Attributes
PTOT_RELATIVE_TO_PMAX
Boolean
Cell total power is absolute value (dBm) or relative to Cell maximum power (%)
Null column allowed: No Default value: False
PUCCH_AVG_NRB
Float
Average number of overhead resource blocks for PUCCH
Null column allowed: No Default value: 2
RS_EPRE_DEFINITION
Short
RS EPRE Definition Method 0 - Calculated from Max Power, 1 - User Defined
Null column allowed: Yes Default value: 0
RSCP_COMPRESSED_THRESH OLD
Float
RSCP threshold for compressed mode activation
Null column allowed: No Default value: -100
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SP_PERIODICITY
Short
Switching point periodicity (TDD) Choice list: 0=Half Frame; 1=Frame;
Null column allowed: Yes Default value: 0
SPREADING_WIDTH
Float
Spreading width (MHz)
Null column allowed: Yes Default value: 3.84
SSF_CONFIG
Short
TDD: Special subframe configuration (0; 1; 2; 3; 4; 5; 6; 7; 8;)
Null column allowed: Yes Default value: 0
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value:
TECHNOLOGY
Text (10)
Name of the technlogy
Null column allowed: No Default value:
THERMAL_NOISE
Float
Thermal noise
Null column allowed: Yes Default value: -121
5.1.11 propagationmodels Table For the table description, see "PropagationModels Table" on page 127.
5.1.12 receivers Table For the table description, see "Receivers Table" on page 34.
5.1.13 repeaterequipments Table For the table description, see "RepeaterEquipments Table" on page 127.
5.1.14 services Table Figure 5.2 on page 149, shows the multi-level definition of the multi-RAT services model tables.
148
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
Figure 5.2: 3GPP Services Model Field
Type
Description
Attributes
DL_ACTIVITY
Float
Activity factor for voice services on the downlink
Null column allowed: Yes Default value: 1
NAME
Text (50)
Service Name
Null column allowed: No Default value:
REQ_AVERAGE_DL_RATE
Float
Requested Average Downlink Rate (kbps)
Null column allowed: Yes Default value:
REQ_AVERAGE_UL_RATE
Float
Requested Average Uplink Rate (kbps)
Null column allowed: Yes Default value:
TECHNO_PRIORITY
Text (50)
List of supported technologies in the order of priority
Null column allowed: No Default value:
UL_ACTIVITY
Float
Activity factor for voice services on the uplink
Null column allowed: Yes Default value: 1
5.1.15 servicesusage Table For the table description, see "T4GServicesUsage Table" on page 136.
5.1.16 sites Table Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude Unit: m
Null column allowed: Yes Default value:
CDMA_EQUIPMENT
Text (50)
Equipment associated with the site
Null column allowed: Yes Default value:
CHANNEL_ELEMENTS_DL
Integer
Number of available channel elements for downlink
Null column allowed: No Default value: 256
CHANNEL_ELEMENTS_UL
Integer
Number of available channel elements for uplink
Null column allowed: No Default value: 256
COMMENT_
Text (255)
Additional information on the site
Null column allowed: Yes Default value:
149
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
Field
Type
Description
Attributes
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
MAX_IUB_RATE_DL
Float
Max Iub Backhaul rate for downlink
Null column allowed: No Default value: 12288
MAX_IUB_RATE_UL
Float
Max Iub Backhaul rate for uplink
Null column allowed: No Default value: 12288
MAX_S1_RATE_DL
Float
Maximum downlink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
MAX_S1_RATE_UL
Float
Maximum uplink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
5.1.17 siteslists Table For the table description, see "SitesLists Table" on page 130.
5.1.18 siteslistsnames Table For the table description, see "SitesListsNames Table" on page 130.
5.1.19 smartantennasmodels Table For the table description, see "SmartAntennasModels Table" on page 130.
5.1.20 terminals Table Figure 5.3 on page 150, shows the multi-level definition of the multi-RAT terminals model tables.
Figure 5.3: 3GPP Terminals Model
150
Field
Type
Description
Attributes
NAME
Text (50)
Name of terminal
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.1.21 tmaequipments Table For the table description, see "TMAEquipments Table" on page 138.
5.1.22 trafficenvs Table For the table description, see "T4GTraficEnvironments Table" on page 137.
5.1.23 units Table For the table description, see "Units Table" on page 46.
5.1.24 userprofiles Table For the table description, see "T4GUserProfiles Table" on page 138.
5.2 GSM-specific Tables Figure 1.1 on page 16, Figure 1.2 on page 17, and Figure 1.3 on page 18 depict the GSM GPRS EDGE database structure.
5.2.1 Changes in Data Structure From 3.1 to 3.2 5.2.1.1 Added Tables and Fields gservices Table Field
Type
Description
Attributes
MIN_THROUGHPUT_UL
Float
Uplink minimum user throughput requested for the service
Null column allowed: Yes Default value: 15
PRIORITY
Short
Service priority (0: lowest)
Null column allowed: Yes Default value: 0
gservicesusage Table Field
Type
Description
Attributes
UL_VOLUME
Float
Volume transferred on the uplink during a session (for packet switched services)
Null column allowed: Yes Default value:
gterminals Table Field
Type
Description
Attributes
PMIN
Float
Minimum receiver power on traffic channels not to exceed
Null column allowed: Yes Default value: -40
gtpltransmitters Table Field
Type
Description
Attributes
NOISE_FIGURE
Float
Total noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value:
REUSE_DISTANCE
Float
Typical reuse distance for assignments
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Default value:
151
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
gtransmitters Table Field
Type
Description
Attributes
NOISE_FIGURE
Float
Total noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
REUSE_DISTANCE
Float
Typical reuse distance for assignments
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Default value: 0
Field
Type
Description
Attributes
VAMOS_RATIO
Float
gtrgs Table
Percentage of VAMOS (Voice services over Adaptive Multi-user channels Null column allowed: Yes on One Slot) traffic in the subcell. Default value: 0
5.2.2 gafpmodels Table For the table description, see "AfpModels Table" on page 20.
5.2.3 gbsicdomains Table For the table description, see "BSICDomains Table" on page 21.
5.2.4 gbsicgroups Table For the table description, see "BSICGroups Table" on page 21.
5.2.5 gcelltypes Table For the table description, see "CellTypes Table" on page 21.
5.2.6 gcodecequipments Table For the table description, see "CodecEquipments Table" on page 22.
5.2.7 gcodecmodeadapts Table For the table description, see "CodecModeAdaptations Table" on page 22.
5.2.8 gcodecmodes Table For the table description, see "CodecModes Table" on page 22.
5.2.9 gcodecqualtables Table For the table description, see "CodecQualityTables Table" on page 23.
5.2.10 gcodingschemes Table For the table description, see "EGPRSCodingSchemes Table" on page 25.
5.2.11 gcsequipments Table For the table description, see "EGPRSEquipments Table" on page 26.
152
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.2.12 gcsquality Table For the table description, see "EGPRSQuality Table" on page 27.
5.2.13 gdimensmodel Table For the table description, see "EGPRSDimensioningModel Table" on page 26.
5.2.14 gfreqdomains Table For the table description, see "FrequencyDomains Table" on page 30.
5.2.15 gfreqgroups Table For the table description, see "FrequencyGroups Table" on page 30.
5.2.16 gfrequencybands Table For the table description, see "FrequencyBands Table" on page 30.
5.2.17 ghsndomains Table For the table description, see "HSNDomains Table" on page 31.
5.2.18 ghsngroups Table For the table description, see "HSNGroups Table" on page 31.
5.2.19 glayers Table For the table description, see "Layers Table" on page 32.
5.2.20 glneighbours Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
5.2.21 glneighconstraints Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
153
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
Field
Type
Description
Attributes
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
5.2.22 gneighbours Table For the table description, see "Neighbours Table" on page 32.
5.2.23 gneighconstraints Table For the table description, see "NeighboursConstraints Table" on page 32.
5.2.24 gneighext Table For the table description, see "NeighboursExt Table" on page 33.
5.2.25 gneighextconstraints Table For the table description, see "NeighboursConstraintsExt Table" on page 32.
5.2.26 gqualityindicators Table For the table description, see "QualityIndicators Table" on page 34.
5.2.27 grepeaters Table For the table description, see "Repeaters Table" on page 35.
5.2.28 gsecondaryantennas Table For the table description, see "SecondaryAntennas Table" on page 35.
5.2.29 gseparationrules Table For the table description, see "SeparationRules Table" on page 36.
5.2.30 gseparations Table For the table description, see "Separations Table" on page 36.
5.2.31 gservicequality Table For the table description, see "EGPRSServiceQuality Table" on page 27.
5.2.32 gservices Table For the table description, see "EGPRSServices Table" on page 27. The table does not contain the following fields: • • • •
DL_ACTIVITY REQ_AVERAGE_DL_RATE REQ_AVERAGE_UL_RATE UL_ACTIVITY
5.2.33 gterminals Table For the table description, see "EGPRSTerminals Table" on page 29.
154
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.2.34 gtpltransmitters Table For the table description, see "TplTransmitters Table" on page 37.
5.2.35 gtransmitters Table For the table description, see "Transmitters Table" on page 39.
5.2.36 gtrgconfigs Table For the table description, see "TRGConfigurations Table" on page 42.
5.2.37 gtrgs Table For the table description, see "TRGs Table" on page 43.
5.2.38 gtrxequipments Table For the table description, see "TRXEquipments Table" on page 44.
5.2.39 gtrxs Table For the table description, see "TRXs Table" on page 45.
5.2.40 gtrxtypes Table For the table description, see "TRXTypes Table" on page 45.
5.2.41 gtsconfignames Table For the table description, see "TSConfigurationNames Table" on page 46.
5.2.42 gtsconfigs Table For the table description, see "TSConfigurations Table" on page 46.
5.2.43 gtxslists Table For the table description, see "TxsLists Table" on page 46.
5.2.44 gtxslistsnames Table For the table description, see "TxsListsNames Table" on page 46.
5.2.45 guneighbours Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
155
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
5.2.46 guneighconstraints Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
5.3 UMTS-specific Tables Figure 2.1 on page 49, Figure 2.2 on page 50, and Figure 2.3 on page 51 depict the UMTS HSPA database structure.
5.3.1 Changes in Data Structure From 3.1 to 3.2 5.3.1.1 Added Tables and Fields ucells Table Field
Type
Description
Attributes
HSDPA_SCHEDULER
Text (50)
HSDPA scheduler
Null column allowed: Default value:
RSCP_MIN
Float
Minimum RSCP reception level (dBm)
Null column allowed: Yes Default value: -150
uequipments Table Field
Type
Description
Attributes
HSDPA_MULTI_BAND
Short
MultiBand activation 0=Inactive; 1=Active
Null column allowed: No Default value: 0
SCHEDULER_ALGO
Text (50)
Scheduler
Null column allowed: Yes Default value:
ufrequencybands Table Field
Type
Description
Attributes
DELTA_CN
Integer
Step between two adjacent carrier numbers
Null column allowed: Yes Default value: 1
EXCLUDED_CHANNELS
Text (255)
List of the forbidden carriers inside this band
Null column allowed: Yes Default value:
uhsupauecategories Table Field
Type
MULTI_CARRIER
Short
Description
Attributes
Multi-carrier mode (0: None; 1: Dual-cell)
Null column allowed: No Default value: 0
umugtables Table (New) Field CELL_NUMBER
156
Type
Description
Attributes
Short
The multi-user diversity gain may be different if the number of cells increase.
Null column allowed: No Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MUG_TABLE
Memo
Multi-user diversity gain table
Null column allowed: Yes Default value:
SCHEDULER_NAME
Text (50)
Name of the scheduler for which the multi-user diversity gain table is defined.
Null column allowed: No Default value:
uneighbours Table Field
Type
Description
Attributes
RELATION_TYPE
Short
The type of the neighbour relation between cells: intra-carrier or intercarrier
Null column allowed: Yes Default value:
uschedulers Table (New) Field
Type
Description
Attributes
NAME
Text (30)
Name of the scheduler
Null column allowed: No Default value:
SCHEDULING_METHOD
Short
0 = Max C/I; 1 = Round-robin; 2 = Proportional Fair
Null column allowed: Yes Default value: 0
uterminals Table Field
Type
Description
Attributes
NOISE_FACTOR_THIRD
Float
Noise figure used to determine the thermal noise at the receiver (for third frequency band)
Null column allowed: Yes Default value: 8
THIRD_BAND
Text (50)
Third frequency band
Null column allowed: Yes Default value:
utpltransmitters Table Field
Type
Description
Attributes
HSDPA_SCHEDULER
Text (50)
HSDPA scheduler
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
MIMO_SUPPORT
Short
Supported MIMO features: 0 = None; 1 = open loop MIMO; 2 = closed loop MIMO
Null column allowed: Yes Default value:
RSCP_MIN
Float
Minimum RSCP reception level (dBm)
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
utransmitters Table Field
Type
Description
Attributes
MAX_RANGE
Integer
Maximum range of coverage
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
5.3.1.2 Deleted Tables and Fields ucells Table • •
HSDPA_MUG_TABLE HSDPA_SCHEDULER_ALGO
utpltransmitters Table •
HSDPA_MUG_TABLE
157
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
• • •
© Forsk 2014
HSDPA_SCHEDULER_ALGO MC_HSDPA_MUG MC_HSDPA_SCHED_ALGO
utransmitters Table • •
MC_HSDPA_MUG MC_HSDPA_SCHED_ALGO
5.3.2 ucells Table For the table description, see "CDMACells Table" on page 55.
5.3.3 uceuse Table For the table description, see "CDMAEquipmentsCEsUse Table" on page 57.
5.3.4 uequipments Table For the table description, see "CDMAEquipments Table" on page 57.
5.3.5 ufrequencybands Table For the table description, see "FrequencyBands Table" on page 60.
5.3.6 ugneighbours Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
5.3.7 ugneighconstraints Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
5.3.8 uhsdpabearers Table For the table description, see "HSDPABearers Table" on page 60.
158
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.3.9 uhsdpabearerselect Table For the table description, see "HSDPABearerSelectTables Table" on page 61.
5.3.10 uhsdpaqualtables Table For the table description, see "HSDPAQualityTables Table" on page 61.
5.3.11 uhspamimoconfigs Table For the table description, see "HSPAMIMOConfigs Table" on page 61.
5.3.12 uhsupabearers Table For the table description, see "HSUPABearers Table" on page 62.
5.3.13 uhsupabearerselect Table For the table description, see "HSUPABearerSelection Table" on page 62.
5.3.14 uhsupaqualtables Table For the table description, see "HSUPAQualityTables Table" on page 62.
5.3.15 uhsuparessuse Table For the table description, see "CdmaEqptsHSUPARssUse Table" on page 56.
5.3.16 uhsupauecategories Table For the table description, see "HSUPAUECategories Table" on page 63.
5.3.17 uinterfreducfactors Table For the table description, see "InterfReductionFactors Table" on page 63.
5.3.18 ulneighbours Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
5.3.19 ulneighconstraints Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
159
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
Field
Type
Description
Attributes
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
5.3.20 umobility Table For the table description, see "UMTSMobility Table" on page 77.
5.3.21 umugtables Table For the table description, see "MUGTables Table" on page 64.
5.3.22 uneighbours Table For the table description, see "Neighbours Table" on page 64.
5.3.23 uneighconstraints Table For the table description, see "NeighboursConstraints Table" on page 64.
5.3.24 uneighext Table For the table description, see "NeighboursExt Table" on page 65.
5.3.25 uneighextconstraints Table For the table description, see "NeighboursConstraintsExt Table" on page 65.
5.3.26 upscdomains Table For the table description, see "ScramblingCodesDomains Table" on page 69.
5.3.27 upscforbidpairs Table For the table description, see "Separations Table" on page 70.
5.3.28 upscgroups Table For the table description, see "ScramblingCodesGroups Table" on page 69.
5.3.29 uqualityindicators Table For the table description, see "QualityIndicators Table" on page 66.
5.3.30 ur99bearers Table For the table description, see "R99Bearers Table" on page 67.
5.3.31 urepeaters Table For the table description, see "Repeaters Table" on page 68.
160
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.3.32 uschedulers Table For the table description, see "Schedulers Table" on page 69.
5.3.33 usecondaryantennas Table For the table description, see "SecondaryAntennas Table" on page 69.
5.3.34 uservicequaltables Table For the table description, see "ServiceQualityTables Table" on page 70.
5.3.35 uservices Table For the table description, see "UMTSServices Table" on page 77. The table does not contain the following fields: • • • •
DL_ACTIVITY REQ_AVERAGE_DL_RATE REQ_AVERAGE_UL_RATE UL_ACTIVITY
5.3.36 uservicesquality Table For the table description, see "UMTSServicesQuality Table" on page 79.
5.3.37 uterminals Table For the table description, see "UMTSTerminals Table" on page 80.
5.3.38 utpltransmitters Table For the table description, see "TplTransmitters Table" on page 71.
5.3.39 utransmitters Table For the table description, see "Transmitters Table" on page 74.
5.3.40 utxslists Table For the table description, see "TxsLists Table" on page 76.
5.3.41 utxslistsnames Table For the table description, see "TxsListsNames Table" on page 76.
5.3.42 uuecategories Table For the table description, see "UECategories Table" on page 76.
5.3.43 uuerxequipments Table For the table description, see "UERxEquipments Table" on page 77.
5.4 LTE-specific Tables Figure 4.1 on page 113, Figure 4.2 on page 114, and Figure 4.3 on page 115 depict the LTE database structure.
161
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
5.4.1 Changes in Data Structure From 3.1 to 3.2 5.4.1.1 Added Tables and Fields lbearersrequiredci Table Field
Type
Description
Attributes
AMS_THRESHOLD
Float
Radio quality required to switch from diversity gains to SU-MIMO throughput gains
Null column allowed: Yes Default value:
MUMIMO_THRESHOLD
Float
Radio quality required to activate MU-MIMO
Null column allowed: Yes Default value:
lcchdivgains Table (New) Field
Type
Description
Attributes
EQUIPMENT
Text (50)
Name of the reception equipment to which the control channel diversity gains correspond
Null column allowed: No Default value:
MIMO_RX_ANTENNAS
Short
Number of reception antennas used for MIMO
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of transmission antennas used for MIMO
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
Name of the mobility type to which the control channel diversity gains correspond
Null column allowed: Yes Default value:
PBCH_DIV_GAIN
Float
PBCH diversity gain
Null column allowed: Yes Default value: 0
PDCCH_DIV_GAIN
Float
PDCCH diversity gain
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
ABS_PATTERN
Text (80)
The pattern of absolute blank subframes with 1=ABS and 0=non-ABS
Null column allowed: Yes Default value:
CELL_TYPE
Short
Type of cell (0 = LTE R8; 1 = LTE R10 PCell; 2 = LTE R10 SCell)
Null column allowed: Yes Default value: 0
DL_MU_SM_GAIN
Float
Downlink MU-MIMO capacity gain
Null column allowed: Yes Default value: 0
P_SCH_ID
Short
Primary Synchronisation Signal ID [0 - 2]
Null column allowed: Yes Default value: 0
PSS_ID_STATUS
Short
PSS ID allocation status (0 = Not allocated, 1 = Allocated, 2 = Locked)
Null column allowed: Yes Default value: 0
S_SCH_ID
Short
Secondary Synchronisation Signal ID [0 - 167]
Null column allowed: Yes Default value: 0
UNIQUE_ID
Text (50)
Unique ID
Null column allowed: Yes Default value:
lcells Table
lframeconfigs Table Field
Type
Description
Attributes
CELLEDGE_PWR_BOOST
Float
Ratio of the transmission power of cell-edge frequency blocks to cellcentre frequency blocks for Soft FFR and Partial Soft FFR
Null column allowed: Yes Default value:
CYCLIC_PREFIX
Short
Cyclic prefix used by data subframes of a cell
Null column allowed: Yes Default value: 0
ICIC_MODE
Short
The inter-cell interference coordination mode of the configuration: 0 – TD-FFR; 1 – Hard FFR; 2 – Soft FFR; 3 – Partial Soft FFR
Null column allowed: No Default value: 0
PDCCH_SYMBOLS
Short
Number of OFDM symbols per subframe corresponding to the PDCCH
Null column allowed: Yes Default value: 1
162
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
PRACH_PREAMBLE_FORMAT
Short
The preamble format for the PRACH
Null column allowed: Yes Default value:
PUCCH_AVG_NRB
Float
Average number of frequency blocks corresponding to the PUCCH
Null column allowed: Yes Default value: 2
lfrequencybands Table Field
Type
Description
Attributes
DELTA_CN
Integer
Step between two adjacent channel numbers
Null column allowed: Yes Default value: 1
llayers Table (New) Field
Type
Description
Attributes
LAYER_INDEX
Short
Index of the network layer
Null column allowed: No Default value: 0
MAX_SPEED
Float
Name of the network layer
Null column allowed: Yes Default value: 300
NAME
Text (50)
Priority of the network layer
Null column allowed: No Default value:
PRIORITY
Short
Maximum speed of mobiles for this layer
Null column allowed: No Default value: 0
SELECTION_MARGIN
Float
Layer selection margin
Null column allowed: Yes Default value: 0
lmimoconfigs Table Field
Type
Description
Attributes
MUMIMO_DIV_GAIN
Float
Diversity gain applicable with MU-MIMO
Null column allowed: Yes Default value: 0
SUMIMO_DIV_GAIN
Float
Diversity gain applicable with SU-MIMO
Null column allowed: Yes Default value: 0
lmugtables Table Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of radio bearer for which the MUG gain is defined
Null column allowed: Yes Default value:
MUG_TABLE_UL
Memo
Uplink multi-user diversity gain table
Null column allowed: Yes Default value:
lservices Table Field
Type
Description
Attributes
MIN_RB_UL
Integer
Minimum number of required frequency blocks for the service
Null column allowed: Yes Default value: 1
QCI
Short
3GPP QCI (QoS Class Identifier) for the service
Null column allowed: Yes Default value:
SUPPORTED_LAYER_LIST
Text (50)
List of network layers on which the service is allowed
Null column allowed: No Default value: “-1”
lterminals Table Field
Type
Description
Attributes
N_SCELLS_DL
Short
Number of secondary cells in downlink (carrier aggregation)
Null column allowed: Yes Default value: 0
163
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
© Forsk 2014
Field
Type
Description
Attributes
N_SCELLS_UL
Short
Number of secondary cells in uplink (carrier aggregation)
Null column allowed: Yes Default value: 0
SUPPORTED_LAYER_LIST
Text (50)
List of network layers supported by the terminal
Null column allowed: No Default value: “-1”
ltpltransmitters Table Field
Type
Description
Attributes
CELL_TYPE
Short
Type of cell (0 = LTE R8; 1 = LTE R10 PCell; 2 = LTE R10 SCell)
Null column allowed: Yes Default value:
LAYER_LIST
Text (255)
List of layers
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
ltransmitters Table Field
Type
Description
Attributes
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
luecategories Table Field
Type
Description
Attributes
UE_CAT_FOR_DOWNGRADE
Text (50)
Name of the UE category for downgrade from LTE R10 to LTE R8
Null column allowed: Yes Default value:
5.4.2 lbearerqualitycurves Table For the table description, see "T4GBearerQualityCurves Table" on page 131.
5.4.3 lbearers Table For the table description, see "T4GBearers Table" on page 131.
5.4.4 lbearersrequiredci Table For the table description, see "T4GBearersRequiredCI Table" on page 131.
5.4.5 lcells Table For the table description, see "T4GCells Table" on page 131.
5.4.6 lcchdivgains Table For the table description, see "lcchdivgains Table" on page 122.
5.4.7 lequipments Table For the table description, see "T4GEquipments Table" on page 134.
5.4.8 lframeconfigs Table For the table description, see "lframeconfigs Table" on page 123.
5.4.9 lfrequencybands Table For the table description, see "FrequencyBands Table" on page 122.
164
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.4.10 lgneighbours Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
5.4.11 lgneighconstraints Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
5.4.12 llayers Table For the table description, see "llayers Table" on page 123.
5.4.13 lmimoconfigs Table For the table description, see "T4GMimoConfigs Table" on page 134.
5.4.14 lmugtables Table For the table description, see "MUGTables Table" on page 124.
5.4.15 lneighbours Table For the table description, see "Neighbours Table" on page 124.
5.4.16 lneighconstraints Table For the table description, see "NeighboursConstraints Table" on page 125.
5.4.17 lneighext Table For the table description, see "NeighboursExt Table" on page 125.
5.4.18 lneighextconstraints Table For the table description, see "NeighboursConstraintsExt Table" on page 125.
165
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
5.4.19 lpcidomains Table For the table description, see "lpcidomains Table" on page 124.
5.4.20 lpcigroups Table For the table description, see "lpcigroups Table" on page 124.
5.4.21 lqualityindicators Table For the table description, see "QualityIndicators Table" on page 127.
5.4.22 lrepeaters Table For the table description, see "Repeaters Table" on page 128.
5.4.23 lschedulers Table For the table description, see "Schedulers Table" on page 129.
5.4.24 lsecondaryantennas Table For the table description, see "SecondaryAntennas Table" on page 129.
5.4.25 lservices Table For the table description, see "T4GServices Table" on page 135. The table does not contain the following fields: • • • •
DL_ACTIVITY REQ_AVERAGE_DL_RATE REQ_AVERAGE_UL_RATE UL_ACTIVITY
5.4.26 lsmartantennas Table For the table description, see "SmartAntennas Table" on page 130.
5.4.27 lterminals Table For the table description, see "T4GTerminals Table" on page 136.
5.4.28 ltpltransmitters Table For the table description, see "TplTransmitters Table" on page 138.
5.4.29 ltransmitters Table For the table description, see "Transmitters Table" on page 141.
5.4.30 ltxslists Table For the table description, see "TxsLists Table" on page 142.
5.4.31 ltxslistsnames Table For the table description, see "TxsListsNames Table" on page 142.
5.4.32 luecategories Table For the table description, see "T4GUECategories Table" on page 137.
166
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
AT321_DSR_E1
5.4.33 luneighbours Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
5.4.34 luneighconstraints Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
167
Atoll 3.2.1 Data Structure Reference Guide Chapter 5: 3GPP Multi-RAT Data Structure
168
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
AT321_DSR_E1
6 3GPP2 Multi-RAT Data Structure 3GPP2 Multi-RAT Atoll documents can contain one or both 3GPP2 technologies: CDMA2000 and LTE. Tables in the 3GPP2 Multi-RAT template include the following categories of tables: •
"Tables Common to All Technologies" on page 169 These tables are shared and used by all the technologies. There structures (fields, keys, and relations with other tables) are similar to the structures of these tables in single-technology documents. The multi-RAT traffic model allows you to define services, terminals, and mobility types, user profiles, and traffic environments for all three technologies. These tables have a multi-level definition: a technology-independent level and a technology-specific level.
• •
"CDMA2000-specific Tables" on page 174 "LTE-specific Tables" on page 177 These tables are specific to technologies. There structures are the same as in single-technology documents.
6.1 Tables Common to All Technologies 6.1.1 antennas Table For the table description, see "Antennas Table" on page 118.
6.1.2 btsequipments Table For the table description, see "BTSEquipments Table" on page 119.
6.1.3 coordsys Table For the table description, see "CoordSys Table" on page 119.
6.1.4 customfields Table For the table description, see "CustomFields Table" on page 120.
6.1.5 environmentdefs Table For the table description, see "T4GEnvironmentDefs Table" on page 134.
6.1.6 feederequipments Table For the table description, see "FeederEquipments Table" on page 121.
6.1.7 internetchprotect Table For the table description, see "InterNetChProtect Table" on page 122. This table contains the following additional field in the 3GPP2 multi-RAT template: Field
Type
Description
Attributes
V_TECHNO
Text (50)
Victim technology
Null column allowed: No Default value:
6.1.8 mobility Table Figure 6.1 on page 170, shows the multi-level definition of the multi-RAT mobility types model tables.
169
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
© Forsk 2014
Figure 6.1: 3GPP2 Mobility Types Model Field
Type
Description
Attributes
NAME
Text (50)
Name of mobility type
Null column allowed: No Default value:
MEAN_SPEED
Float
Average speed (km/h)
Null column allowed: No Default value:
6.1.9 networks Table The networks table contains one record for each technology in the document. In each record, only parameters relevant for the row’s technology are used. Field
Type
Description
Attributes
ADD_MRC_SOFTERSOFT
Boolean
If true, gain due to MRC is taken into account for softer/soft cases
Null column allowed: No Default value: False
AMS_SEL_CRITERION
Short
AMS criterion (0 - Reference signal C/N; 1 - Reference signal C/(I+N))
Null column allowed: Yes Default value: 0
BS_SELECTION
Short
Best server selection method: 0=RS C; 1=RSRP;
Null column allowed: Yes Default value: 0
CELL_SELECTION
Short
Serving cell selection method (0 = Min DL Load, 1 = Min UL Load, 2 = Random, 3 = Sequential)
Null column allowed: Yes Default value: 2
DEFAULT_CP
Short
Default cyclic prefix Choice list: 0=Normal; 1=Extended;
Null column allowed: Yes Default value: 0
DEFAULT_HOGAIN_UL
Float
Default soft handoff gain uplink
Null column allowed: No Default value: 0
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: "CostHata"
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -130
IOISNTOT
Boolean
Io includes pilot signal or not
Null column allowed: No Default value: True
MIMO_INT_PWR_COMB
Short
Whether interfering signals are combined over multiple antennas or not
Null column allowed: Yes Default value: 1
MUMIMO_CRITERION
Short
Radio conditions based on which MU-MIMO is activated or not
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of network
Null column allowed: No Default value:
NTISNTOT
Boolean
Nt includes pilot signal or not
Null column allowed: No Default value: False
170
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
PDCCH_SYMBOLS
Short
Number of symbol durations per subframe for PDCCH overhead
Null column allowed: No Default value: 1
POWER_CONTROL_MARGIN
Float
Margin Over Max Bearer Threshold defining C/I Target (dB)
Null column allowed: Yes Default value: 1
POWERS_RELATIVE_TO_PILO T
Boolean
Cell paging and Synchro powers, Service Allowed DL min and max TCH powers are absolute values or relative to cell pilot power
Null column allowed: No Default value: False
PTOT_RELATIVE_TO_PMAX
Boolean
Cell total power is absolute value (dBm) or relative to Cell maximum power (%)
Null column allowed: No Default value: False
PUCCH_AVG_NRB
Float
Average number of overhead resource blocks for PUCCH
Null column allowed: No Default value: 2
RS_EPRE_DEFINITION
Short
RS EPRE Definition Method 0 - Calculated from Max Power, 1 - User Defined
Null column allowed: Yes Default value: 0
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SP_PERIODICITY
Short
Switching point periodicity (TDD) Choice list: 0=Half Frame; 1=Frame;
Null column allowed: Yes Default value: 0
SPREADING_WIDTH
Float
Spreading width (MHz)
Null column allowed: Yes Default value: 3.84
SSF_CONFIG
Short
TDD: Special subframe configuration (0; 1; 2; 3; 4; 5; 6; 7; 8;)
Null column allowed: Yes Default value: 0
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value:
TECHNOLOGY
Text (10)
Name of the technlogy
Null column allowed: No Default value:
THERMAL_NOISE
Float
Thermal noise
Null column allowed: Yes Default value: -121
UL_PWC_ON_PILOT
Boolean
True if uplink power control is based on pilot’s target
Null column allowed: No Default value: False
6.1.10 propagationmodels Table For the table description, see "PropagationModels Table" on page 127.
6.1.11 receivers Table For receiver parameters. Field
Type
Description
Attributes
ADJ_CHANNEL_PROT
Float
Protection against interfering signals from adjacent channels.
Null column allowed: No Default value: 18
ANTENNA
Text (50)
Receiver antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the receiver
Null column allowed: No Default value: 1.5
LOSS
Float
Losses due to receiver radio equipment (up and downlink)
Null column allowed: No Default value: 0
NAME
Text (50)
Receiver name
Null column allowed: No Default value:
6.1.12 repeaterequipments Table For the table description, see "RepeaterEquipments Table" on page 127.
6.1.13 services Table Figure 6.2 on page 172, shows the multi-level definition of the multi-RAT services model tables.
171
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
© Forsk 2014
Figure 6.2: 3GPP2 Services Model Field
Type
Description
Attributes
DL_ACTIVITY
Float
Activity factor for voice services on the downlink
Null column allowed: Yes Default value: 1
NAME
Text (50)
Service Name
Null column allowed: No Default value:
REQ_AVERAGE_DL_RATE
Float
Requested Average Downlink Rate (kbps)
Null column allowed: Yes Default value:
REQ_AVERAGE_UL_RATE
Float
Requested Average Uplink Rate (kbps)
Null column allowed: Yes Default value:
TECHNO_PRIORITY
Text (50)
List of supported technologies in the order of priority
Null column allowed: No Default value:
UL_ACTIVITY
Float
Activity factor for voice services on the uplink
Null column allowed: Yes Default value: 1
6.1.14 servicesusage Table For the table description, see "T4GServicesUsage Table" on page 136.
6.1.15 sites Table Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude Unit: m
Null column allowed: Yes Default value:
CDMA_EQUIPMENT
Text (50)
Equipment associated with the site
Null column allowed: Yes Default value:
CHANNEL_ELEMENTS_DL
Integer
Number of available channel elements for downlink
Null column allowed: No Default value: 256
CHANNEL_ELEMENTS_UL
Integer
Number of available channel elements for uplink
Null column allowed: No Default value: 256
172
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
COMMENT_
Text (255)
Additional information on the site
Null column allowed: Yes Default value:
EVDO_CES
Integer
Number of EVDO CEs per carrier
Null column allowed: Yes Default value: 96
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
MAX_S1_RATE_DL
Float
Maximum downlink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
MAX_S1_RATE_UL
Float
Maximum uplink user throughput supported by the S1 interface excluding control plane messaging, GTP-U/UDP/IP headers, and other
Null column allowed: Yes Default value: 950000
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
6.1.16 siteslists Table For the table description, see "SitesLists Table" on page 130.
6.1.17 siteslistsnames Table For the table description, see "SitesListsNames Table" on page 130.
6.1.18 smartantennasmodels Table For the table description, see "SmartAntennasModels Table" on page 130.
6.1.19 terminals Table Figure 6.3 on page 174, shows the multi-level definition of the multi-RAT terminals model tables.
173
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
© Forsk 2014
Figure 6.3: 3GPP2 Terminals Model Field
Type
Description
Attributes
NAME
Text (50)
Name of terminal
Null column allowed: No Default value:
6.1.20 tmaequipments Table For the table description, see "TMAEquipments Table" on page 138.
6.1.21 trafficenvs Table For the table description, see "T4GTraficEnvironments Table" on page 137.
6.1.22 units Table For the table description, see "Units Table" on page 142.
6.1.23 userprofiles Table For the table description, see "T4GUserProfiles Table" on page 138.
6.2 CDMA2000-specific Tables Figure 3.1 on page 83, Figure 3.2 on page 84, and Figure 3.3 on page 85 depict the CDMA2000 database structure.
6.2.1 ccarrierstype Table For the table description, see "CarriersType Table" on page 88.
174
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
AT321_DSR_E1
6.2.2 ccells Table For the table description, see "CDMACells Table" on page 88.
6.2.3 cceuse Table For the table description, see "CDMAEquipmentsCEsUse Table" on page 90.
6.2.4 cdlbearerselect Table For the table description, see "DLBearersSelection Table" on page 92.
6.2.5 cdldorabearers Table For the table description, see "DLDORABearers Table" on page 93.
6.2.6 cdorabearers Table For the table description, see "DORABearers Table" on page 93.
6.2.7 cdorabearersproba Table For the table description, see "DORABearersProba Table" on page 93.
6.2.8 cdoratermt2pratios Table For the table description, see "DORATerminalT2PRatios Table" on page 93.
6.2.9 cequipments Table For the table description, see "CDMAEquipments Table" on page 89.
6.2.10 cfrequencybands Table For the table description, see "FrequencyBands Table" on page 94.
6.2.11 cinterfreducfactors Table For the table description, see "InterfReductionFactors Table" on page 94.
6.2.12 clneighbours Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
175
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
© Forsk 2014
6.2.13 clneighconstraints Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
6.2.14 cmobility Table For the table description, see "UMTSMobility Table" on page 106.
6.2.15 cneighbours Table For the table description, see "Neighbours Table" on page 95.
6.2.16 cneighconstraints Table For the table description, see "NeighboursConstraints Table" on page 95.
6.2.17 cneighext Table For the table description, see "NeighboursExt Table" on page 96.
6.2.18 cneighextconstraints Table For the table description, see "NeighboursConstraintsExt Table" on page 95.
6.2.19 cpnodomains Table For the table description, see "PnCodesDomains Table" on page 97.
6.2.20 cpnoforbidpairs Table For the table description, see "Separations Table" on page 100.
6.2.21 cpnogroups Table For the table description, see "PnCodesGroups Table" on page 97.
6.2.22 cqualityindicators Table For the table description, see "QualityIndicators Table" on page 97.
6.2.23 crepeaters Table For the table description, see "Repeaters Table" on page 99.
6.2.24 csecondaryantennas Table For the table description, see "SecondaryAntennas Table" on page 99.
176
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
AT321_DSR_E1
6.2.25 cservicequaltables Table For the table description, see "ServiceQualityTables Table" on page 100.
6.2.26 cservices Table For the table description, see "UMTSServices Table" on page 107.
6.2.27 cservicesquality Table For the table description, see "UMTSServicesQuality Table" on page 108.
6.2.28 cterminals Table For the table description, see "UMTSTerminals Table" on page 109.
6.2.29 ctpltransmitters Table For the table description, see "TplTransmitters Table" on page 101.
6.2.30 ctransmitters Table For the table description, see "Transmitters Table" on page 104.
6.2.31 ctxslists Table For the table description, see "TxsLists Table" on page 105.
6.2.32 ctxslistsnames Table For the table description, see "TxsListsNames Table" on page 106.
6.2.33 cuerxequipments Table For the table description, see "UERxEquipments Table" on page 106.
6.2.34 culbearerselect Table For the table description, see "ULBearersSelection Table" on page 106.
6.3 LTE-specific Tables Figure 4.1 on page 113, Figure 4.2 on page 114, and Figure 4.3 on page 115 depict the LTE database structure.
6.3.1 lbearerqualitycurves Table For the table description, see "T4GBearerQualityCurves Table" on page 131.
6.3.2 lbearers Table For the table description, see "T4GBearers Table" on page 131.
6.3.3 lbearersrequiredci Table For the table description, see "T4GBearersRequiredCI Table" on page 131.
177
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
© Forsk 2014
6.3.4 lcells Table For the table description, see "T4GCells Table" on page 131.
6.3.5 lcchdivgains Table For the table description, see "lcchdivgains Table" on page 122.
6.3.6 lcneighbours Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
6.3.7 lcneighconstraints Table Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
6.3.8 lequipments Table For the table description, see "T4GEquipments Table" on page 134.
6.3.9 lframeconfigs Table For the table description, see "lframeconfigs Table" on page 123.
6.3.10 lfrequencybands Table For the table description, see "FrequencyBands Table" on page 122.
6.3.11 llayers Table For the table description, see "llayers Table" on page 123.
6.3.12 lmimoconfigs Table For the table description, see "T4GMimoConfigs Table" on page 134.
178
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
AT321_DSR_E1
6.3.13 lmugtables Table For the table description, see "MUGTables Table" on page 124.
6.3.14 lneighbours Table For the table description, see "Neighbours Table" on page 124.
6.3.15 lneighconstraints Table For the table description, see "NeighboursConstraints Table" on page 125.
6.3.16 lneighext Table For the table description, see "NeighboursExt Table" on page 125.
6.3.17 lneighextconstraints Table For the table description, see "NeighboursConstraintsExt Table" on page 125.
6.3.18 lpcidomains Table For the table description, see "lpcidomains Table" on page 124.
6.3.19 lpcigroups Table For the table description, see "lpcigroups Table" on page 124.
6.3.20 lqualityindicators Table For the table description, see "QualityIndicators Table" on page 127.
6.3.21 lrepeaters Table For the table description, see "Repeaters Table" on page 128.
6.3.22 lschedulers Table For the table description, see "Schedulers Table" on page 129.
6.3.23 lsecondaryantennas Table For the table description, see "SecondaryAntennas Table" on page 129.
6.3.24 lservices Table For the table description, see "T4GServices Table" on page 135. The table does not contain the following fields: • • • •
DL_ACTIVITY REQ_AVERAGE_DL_RATE REQ_AVERAGE_UL_RATE UL_ACTIVITY
6.3.25 lsmartantennas Table For the table description, see "SmartAntennas Table" on page 130.
6.3.26 lterminals Table For the table description, see "T4GTerminals Table" on page 136.
179
Atoll 3.2.1 Data Structure Reference Guide Chapter 6: 3GPP2 Multi-RAT Data Structure
6.3.27 ltpltransmitters Table For the table description, see "TplTransmitters Table" on page 138.
6.3.28 ltransmitters Table For the table description, see "Transmitters Table" on page 141.
6.3.29 ltxslists Table For the table description, see "TxsLists Table" on page 142.
6.3.30 ltxslistsnames Table For the table description, see "TxsListsNames Table" on page 142.
6.3.31 luecategories Table For the table description, see "T4GUECategories Table" on page 137.
180
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
7 TD-SCDMA Data Structure This section describes the TD-SCDMA data structure used in Atoll. Figure 7.1 on page 181, Figure 7.2 on page 182, and Figure 7.3 on page 183 depict the structure of the TD-SCDMA database . The following subsections list the tables in the TDSCDMA database template.
Figure 7.1: TD-SCDMA Template - 1
181
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Figure 7.2: TD-SCDMA Template - 2
182
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Figure 7.3: TD-SCDMA Template - 3
183
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
7.1 Data Structure Changes Between Atoll 3.1 and 3.2 7.1.1 Added Tables and Fields Antennas Table Field
Type
Description
Attributes
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
CdmaCells Table Field
Type
Description
Attributes
RSCP_MIN
Float
Min RSCP reception level (dBm)
Null column allowed: Yes Default value: -150
CustomFields Table Field
Type
Description
Attributes
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
Sites Table
TplTransmitters Table Field
Type
Description
Attributes
RSCP_MIN
Float
Min RSCP reception level (dBm)
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
Transmitters Table Field
Type
Description
Attributes
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
7.1.2 Deleted Tables and Fields Sites Table •
SUPPORT_NATURE
7.2 Antennas Table For antennas. Field
184
Type
Description
Attributes
Beamwidth
Float
Antenna beamwidth
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about antenna
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
CONSTRUCTOR
Text (50)
Antenna manufacturer name
Null column allowed: Yes Default value:
DIAGRAM
Binary
Antenna horizontal and vertical patterns
Null column allowed: Yes Default value:
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
ELECTRICAL_TILT
Float
Antenna electrical tilt (for information)
Null column allowed: Yes Default value:
FMax
Double
Maximum operating frequency of the antennas Unit: MHz
Null column allowed: Yes Default value:
FMin
Double
Minimum operating frequency of the antenna Unit: MHz
Null column allowed: Yes Default value:
GAIN
Float
Antenna isotropic gain Unit: dBi
Null column allowed: No Default value: 0
NAME
Text (50)
Name of antenna
Null column allowed: No Default value:
PHYSICAL_ANTENNA
Text (50)
Physical antenna name
Null column allowed: Yes Default value:
The format of the binary field, DIAGRAM, is described in "RF 2D Antenna Pattern Format" on page 275.
7.3 AntennasLists Table For antennas belonging to antenna lists. Field
Type
Description
Attributes
ANTENNA_NAME
Text (50)
First part of the unique key. Name of the list.
Null column allowed: No Default value:
LIST_NAME
Text (50)
Second part of the unique key. Name of the antenna.
Null column allowed: No Default value:
7.4 AntennasListsNames Table For names of antenna lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
7.5 BTSEquipments Table For NodeB equipment. Field
Type
Description
Attributes
CONFIG_DL_LOSSES
Float
Downlink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
CONFIG_UL_LOSSES
Float
Uplink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Base Station Equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Base Station
Null column allowed: Yes Default value: 0
185
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
RHO_FACTOR
Short
Rho factor to model self generated interference (100%=ideal)
Null column allowed: Yes Default value: 100
7.6 CDMACells Table For cells. Field
Type
Description
Attributes
ACTIVE
Boolean
Cell's activity: 'Yes' means that the cell is active
Null column allowed: No Default value: True
CARRIER
Integer
Carrier number
Null column allowed: Yes Default value: 0
CARRIER_TYPE
Short
Carrier type: 0=None; 1=Master; 2=Slave;
Null column allowed: Yes Default value: 0
CELL_ID
Text (50)
Name of the cell
Null column allowed: No Default value:
CELL_IDENTITY
Integer
Cell identity
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the cell
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value: 0
DWPCH_POWER
Float
Power on the DwPTS timeslot
Null column allowed: Yes Default value: 36
DYN_EDCH_DL_POWER_ALL OC
Boolean
Allocation of power for HSUPA DL power (E-AGCH, E-HICH): True=Dynamic; False=Static;
Null column allowed: No Default value: False
DYN_HS_SCCH_POWER_ALL OC
Boolean
Allocation of power for HS_SCCH (True=Dynamic, False=Static)
Null column allowed: No Default value: True
DYN_HS_SICH_POWER_ALLO C
Boolean
Allocation of power for HS-SICH (True=Dynamic, False=Static)
Null column allowed: No Default value: True
DYN_HSDPA_POWER_ALLOC
Boolean
Allocation of power for HSDPA (True=Dynamic, False=Static)
Null column allowed: No Default value: True
EDCH_DL_POWER
Float
Value of power dedicated to E-AGCH and E-HICH channel per timeslot. In case of dynamic allocation, it is the maximum available power.
Null column allowed: Yes Default value:
HS_SCCH_POWER
Float
Value of power dedicated to a HS-SCCH channel. In case of dynamic allocation, it is the maximum available power.
Null column allowed: Yes Default value:
HSDPA_MAX_CODES
Short
Maximum number of HS-PDSCH codes
Null column allowed: Yes Default value: 16
HSDPA_MAX_USERS
Short
Max number of HSDPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value: 64
HSDPA_MIN_CODES
Short
Minimum Number of HS-PDSCH codes
Null column allowed: Yes Default value: 0
HSDPA_PWR
Float
Amount of power (dBm) dedicated to HSDPA
Null column allowed: Yes Default value:
HSDPA_SCHEDULER_ALGO
Short
HSPA_SUPPORT
Short
HSPA features supported: 0=None; 1=HSDPA; 2=HSPA;
Null column allowed: No Default value: 0
HSUPA_MAX_USERS
Integer
Max number of HSUPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value: 15
LOCKED_SC
Boolean
Field used to freeze allocated SC of the cell during automatic allocation
Null column allowed: No Default value: False
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum number of inter-technology neighbours for the cell
Null column allowed: Yes Default value:
186
Scheduling algo used for HSDPA users. 0 = MAX C/I, 1 = Round Robin, 2 = Null column allowed: Yes Proportional Fair. Default value: 2
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MAX_NEIGHB_NUMBER
Integer
Maximum number of neighbours for the cell
Null column allowed: Yes Default value:
MAX_R99BEARER_DL_RATE
Float
Max bearer rate available in DL (kbps)
Null column allowed: Yes Default value: 1000
MAX_R99BEARER_UL_RATE
Float
Max bearer rate available in UL (kbps)
Null column allowed: Yes Default value: 1000
NUM_HS_SCCH
Short
Number of HS-SCCH channels
Null column allowed: Yes Default value: 5
NUM_HS_SICH
Short
Number of HS-SICH channels per cell
Null column allowed: Yes Default value: 5
NUM_HSDPA_USERS
Integer
Number of served HSDPA users in the cell: calculated by the TD-SCDMA Null column allowed: Yes simulation algorithm Default value:
NUM_HSUPA_USERS
Integer
Number of served HSUPA users in the cell: calculated by the TD-SCDMA Null column allowed: Yes simulation algorithm Default value:
OTHERS_CCH_POWER
Float
Power on the other common channels for TS0 (S-CCPCH, FPACH, PICH)
Null column allowed: Yes Default value: 0
PILOT_POWER
Float
Power of the pilot channel
Null column allowed: Yes Default value: 33
POWER_MAX
Float
Maximum power supported by the transmitter
Null column allowed: Yes Default value: 43
PWR_HEADROOM
Float
Power Control Headroom (dB) for DCH (used in WCDMA simulation algorithm)
Null column allowed: Yes Default value: 0
REQ_DL_RUS
Short
Required resource units in downlink
Null column allowed: Yes Default value: 0
REQ_UL_RUS
Short
Required resource units in uplink
Null column allowed: Yes Default value: 0
REUSE_DIST
Float
Minimum reuse distance for scrambling codes
Null column allowed: Yes Default value:
RSCP_COMP
Float
P-CCPCH RSCP margin to trigger Baton Handover
Null column allowed: Yes Default value: 5
RSCP_MIN
Float
Min RSCP reception level (dBm)
Null column allowed: Yes Default value: -150
SC_DOMAIN_NAME
Text (50)
Scrambling code domain name.
Null column allowed: Yes Default value:
SCRAMBLING_CODE
Integer
Scrambling code.
Null column allowed: Yes Default value:
TS_CONFIG
Integer
Timeslot configuration (1-DUDDDDD; 2-DUUDDDD; 3-DUUUDDD; 4-DUUUUDD; 5-DUUUUUD; 6-DUUUUUU;)
Null column allowed: Yes Default value: 3
TX_ID
Text (50)
Name of the transmitter
Null column allowed: No Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value: 0
7.7 CDMACellsTS Table For timeslots. Field
Type
Description
Attributes
BLOCKED
Boolean
Allow to block the timeslot: 'Yes' means that the timeslot is blocked
Null column allowed: No Default value: False
CELL_ID
Text (50)
Name of the cell
Null column allowed: No Default value:
DL_ANGULAR_POWERS
Binary
Angular distribution of downlink transmitted power
Null column allowed: Yes Default value:
187
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
HSDPA_MAX_CODES
Short
Maximum number of HS-PDSCH codes
Null column allowed: Yes Default value:
HSDPA_MIN_CODES
Short
Minimum number of HS-PDSCH codes
Null column allowed: Yes Default value:
HSDPA_PWR
Float
Amount of power (dBm) dedicated to HSDPA
Null column allowed: Yes Default value:
HSUPA_UL_LOAD
Float
Uplink load factor due to HSUPA users
Null column allowed: Yes Default value:
MAX_DL_LOAD
Float
Maximum downlink load allowed (percentage of max power used). Used in power control simulation
Null column allowed: Yes Default value: 75
MAX_UL_LOAD
Float
Maximum uplink load allowed (percentage). Used in power control simulation
Null column allowed: Yes Default value: 50
OTHERS_CCH_POWER
Float
Power on the other common channels
Null column allowed: Yes Default value: -200
RU_OVERHEAD
Short
Overhead due to signalling channels
Null column allowed: Yes Default value: 0
TIME_SLOT
Short
Time slot number
Null column allowed: No Default value:
TIME_SLOT_TYPE
Short
Type of timeslot (0 = R99, 1 = HSDPA, 2 = R99 + HSDPA)
Null column allowed: No Default value: 0
TOTAL_POWER
Float
Total downlink power: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UL_LOAD
Float
Uplink cellr load factor: manually specified by the user or calculated by the WCDMA simulation algorithm
Null column allowed: Yes Default value:
UL_REUSE_FACTOR
Float
Uplink (I intra+ I extra)/ I intra: calculated by the TD-SCDMA simulation algorithm
Null column allowed: Yes Default value:
7.8 CDMAEquipments Table For site equipment. Field
Type
Description
Attributes
MANUFACTURER
Text (50)
Name of the manufacturer
Null column allowed: Yes Default value:
MCJD_FACTOR
Float
Multi cell joint detection factor for extra cell UL interference cancellation
Null column allowed: No Default value: 0
MUD_FACTOR
Float
MUD factor for UL interference cancellation
Null column allowed: No Default value: 0
NAME
Text (50)
Equipment name
Null column allowed: No Default value:
7.9 CDMAEquipmentsCEsUse Table For channel elements consumption in site equipment.
188
Field
Type
Description
Attributes
CHANNEL_ELTS_DL
Integer
Number of channel elements used for downlink
Null column allowed: No Default value: 1
CHANNEL_ELTS_UL
Integer
Number of channel elements used for uplink
Null column allowed: No Default value: 1
EQUIPMENT
Text (50)
First part of the unique key. Name of equipment
Null column allowed: No Default value:
SERVICE
Text (50)
Second part of the unique key. Service name.
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
7.10 CodesRelativityClusters Table For scrambling code clusters. Field
Type
Description
Attributes
CODES_LIST
Text (255)
Coma separated list of codes belonging to the cluster
Null column allowed: No Default value:
NAME
Text (50)
Name of the cluster of scrambling codes
Null column allowed: No Default value:
7.11 CoordSys Table For the projection coordinate system and the database’s internal coordinate system ( this is the display coordinate system used when creating a database). Field
Type
Description
Attributes
CODE
Integer
Identification number of the coordinate system (the code of userdefined coordinate systems is an integer higher than 32768)
Null column allowed: No Default value: 0
DATUM_CODE
Double
DATUM_ROTX
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTY
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTZ
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_SCALE
Double
Parts per million (ppm)
Null column allowed: Yes Default value: 0
DATUM_SHIFTX
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTY
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTZ
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_CODE
Integer
ELLIPS_RMAJOR
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_RMINOR
Double
Meters
Null column allowed: Yes Default value: 0
NAME
Text (50)
Coordinate system name
Null column allowed: No Default value:
PROJ_ANGLE
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_FALSE_EASTING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FALSE_NORTHING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FIRST_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LATITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LONGITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
Null column allowed: No Default value: 0
189
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
Field
© Forsk 2014
Type
Description
Attributes
PROJ_METHOD
Short
UTM, Undefined, NoProjection, Lambert1SP, Lambert2SP, Mercator, CassiniSoldner, TransMercator, TransMercatorSO, ObliqueStereographic, NewZealandMapGrid, HotineOM, LabordeOM, SwissObliqueCylindical
Null column allowed: Yes Default value: 0
PROJ_SCALE_FACTOR
Double
PROJ_SECOND_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_ZONE_NUMBER
Integer
Used with UTM
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
7.12 CustomFields Table For defining user-defined fields added to tables, default values for any field (including user-defined fields), and choice lists, captions, and group names for user-defined fields. Field
Type
Description
Attributes
CAPTION
Text (50)
Caption of the field (displayed instead of the name)
Null column allowed: Yes Default value:
CHOICE_LIST
Memo
Choice list for the field
Null column allowed: Yes Default value:
CHOICE_TYPE
Integer
0=Choice list is optional; 1=Choice list is mandatory
Null column allowed: Yes Default value: 0
COLUMN_NAME
Text (50)
Second part of the unique key. Field name
Null column allowed: No Default value:
DEFAULT_VALUE
Text (50)
Default value for the field
Null column allowed: Yes Default value:
DISPLAY_TYPE
Integer
0=Field is modifiable; 1=Field is read-only
Null column allowed: Yes Default value: 0
GROUP_NAME
Text (50)
Name of the group to which that field belongs
Null column allowed: Yes Default value:
TABLE_NAME
Text (50)
First part of the unique key. Table name
Null column allowed: No Default value:
These are some general recommendations that you should follow when handling databases. General • • • •
In order to use Atoll with Oracle, you must create Oracle users and schema with names in uppercase. Create backups of the database before upgrading. It is recommended to define a rule for making backups of the database at regular intervals. Do not skip a major Atoll version. For example, if you are currently using Atoll 2.7.xV6.7, you should first upgrade the database to Atoll 2.8.xV6.9 before upgrading to Atoll 3.1.xV7.1. Upgrading your database will be simpler if you do not skip a major version. If you skip or have skipped an intermediate major version, you must upgrade your database twice in order to make it compatible with the new version.
Tables and Fields • •
Table and field names are case sensitive. Table and field names should be not more than 20 characters long. Oracle databases allow a maximum length of 30 characters for field and table names. However, for use in Atoll, you must not create tables and fields with names longer than 20 characters. This is because Atoll adds some characters to the table and field names for certain operations: creating associated triggers, creating project databases, etc. Limiting the length of table and field names to 20 characters will help avoid database connection and consistency problems.
• • •
190
Table and field names should only use alphanumeric characters (A-Z, a-z, 0-9) and underscores (_). Table and field names must not start with a numeric character (0-9). Table and field names must not contain an SQL or RDBMS-specific keyword, such as ORDER, DATE, etc.
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
• • •
• •
Table and field names must not contain spaces or special characters, such as periods (.), exclamation marks (!), colons (:), semi-colons (;), interrogation marks (?), parentheses (()), brackets ({}), square brackets ([]), etc. Boolean fields, system or user-defined, should always have default values assigned. The CustomFields table enables you to define default values, choice lists, and read/write access for any field in any table in Atoll, including user-defined fields that you add to the Atoll tables. The values defined in this table have priority over the internal predefined default values. If you define floating point default values, make sure that all the users have the same decimal separator. If you wish to add custom fields in the Atoll document, you should first add the field in the database, and then update your Atoll document from the database. When setting up your database for the first time, try to anticipate user requirements in terms of custom fields in Atoll tables. Some requirements of the different user groups can be satisfied if a few general-purpose user-defined fields are added in Atoll tables when setting up the database. For example, if you add three user-defined fields (one of type integer, float, and text (limited size)) to the Sites and Transmitters tables, users will be able to use these for sorting, filtering, grouping, or other purposes. This approach can help the database function a long time before users require the addition of other custom fields.
• •
•
To improve performance, if your projects allow it, reduce the size of the fields corresponding to the sites and transmitters’ names. To improve performance, unless absolutely necessary, do not add user-defined fields of Text type. Rather, use numeric field types, which allow sorting and other functions. If you must add Text fields, allocate them the appropriate size that would suffice. For example, a 255-character long Text type field would, for the most part, occupy disk space for no purpose. To improve performance, you should avoid adding custom fields to the neighbour management tables.
7.13 FeederEquipments Table For feeders. Field
Type
Description
Attributes
CONNECTOR_LOSSES_DL
Float
Feeder connector losses in downlink
Null column allowed: Yes Default value: 0
CONNECTOR_LOSSES_UL
Float
Feeder connector losses in uplink
Null column allowed: Yes Default value: 0
LOSS_PER_METER
Float
Feeder loss per meter
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Feeder
Null column allowed: No Default value:
7.14 FrequencyBands Table For frequency bands. Field
Type
Description
Attributes
BAND_WIDTH
Double
Bandwidth (MHz)
Null column allowed: Yes Default value: 1.6
FIRST_CARRIER
Integer
Number of the first carrier available on the network
Null column allowed: Yes Default value: 0
FREQUENCY
Double
Average frequency of carriers Unit: MHz
Null column allowed: Yes Default value: 2010
LAST_CARRIER
Integer
Number of the last carrier available on the network
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the frequency band
Null column allowed: No Default value:
SPREADING_WIDTH
Double
Spreading bandwidth definition
Null column allowed: Yes Default value: 1.28
7.15 HSDPABearers Table For HSDPA bearers.
191
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
BEARER_INDEX
Short
Unique key to address bearer
Null column allowed: No Default value: 1
HSPDSCH_NUM
Short
Number of HS_PDSCH channels used
Null column allowed: Yes Default value: 5
MODULATION
Short
Modulation: 0=QPSK; 1=16QAM;
Null column allowed: No Default value: 0
RLC_PEAK_THROUGHPUT
Float
Peak RLC throughput (without BLER consideration)
Null column allowed: Yes Default value: 0
TRANSPORT_BL_SIZE
Integer
Transport Block Size (bits)
Null column allowed: Yes Default value: 0
TS_NUM
Short
Number of time slots used per subframe
Null column allowed: Yes Default value: 1
UE_CATEGORY
Short
Associated UE category [1-15]
Null column allowed: Yes Default value: 1
7.16 HSDPABearerSelectTables Table For HSDPA bearer selection graphs. Field
Type
Description
Attributes
BEARER_INDEX
Short
Bearer index
Null column allowed: Yes Default value: 0
HSPDSCH_ECNT_REQ
Float
Requried HS-PDSCH Ec/Nt
Null column allowed: Yes Default value: 5
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: Yes Default value: “Standard”
7.17 HSUPABearers For HSUPA bearers. Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of the bearer
Null column allowed: No Default value:
EPUCH_NUM
Short
Number of E-PUCH codes used
Null column allowed: Yes Default value:
MODULATION
Short
Modulation: 0=QPSK; 1=16QAM;
Null column allowed: No Default value: 0
RLC_PEAK_THROUGHPUT
Float
Peak RLC throughput (without BLER)
Null column allowed: Yes Default value:
TRANSPORT_BL_SIZE
Integer
Transport Block Size (bits)
Null column allowed: Yes Default value:
TS_NUM
Short
Number of time slots used per subframe
Null column allowed: Yes Default value: 1
UE_CATEGORY
Short
Associated UE category
Null column allowed: Yes Default value: 1
7.18 HSUPABearerSelection For HSUPA bearer selection graphs.
192
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of the selected bearer
Null column allowed: Yes Default value: 0
EARLY_TERM_TABLE
Memo
Tables of probabilities of earlier termination=f(REPEAT_NUM)
Null column allowed: Yes Default value:
EPUCH_ECNT_REQ
Float
Required E-PUCH Ec/Nt
Null column allowed: Yes Default value:
MAX_NUM_REP
Integer
Number of retransmissions to ensure a correct transmission
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
User’s mobility
Null column allowed: Yes Default value:
RX_EQUIP
Text (50)
Reception equipment of the terminal
Null column allowed: Yes Default value:
UL_CRT_MARGIN
Float
Uplink control margin for E-PUCH
Null column allowed: Yes Default value:
7.19 HSUPAUECategories For HSUPA UE categories. Field
Type
Description
Attributes
MAX_BLOCK_SIZE
Integer
Maximum transport block size supported for TTI=10ms (bits)
Null column allowed: Yes Default value:
MAX_EPUCH_CODES
Short
Maximum number of E-DPDCH codes for HSUPA
Null column allowed: Yes Default value:
MAX_EPUCH_TS
Integer
Smallest Spreading Factor supported
Null column allowed: Yes Default value:
MODULATION
Short
Modulation (0: QPSK; 1: 16QAM)
Null column allowed: No Default value: 0
UE_CATEGORY
Short
UE category for HSUPA
Null column allowed: No Default value:
UE_CATEGORY_NAME
Text (50)
Name of the HSUPA UE category
Null column allowed: Yes Default value:
7.20 InterfReductionFactors Table For interference reduction factors between carriers. Field
Type
Description
Attributes
CARRIER1
Integer
First carrier
Null column allowed: No Default value: 0
CARRIER2
Integer
Second carrier
Null column allowed: No Default value: 0
FACTOR
Double
Interference reduction factor
Null column allowed: No Default value: 200
7.21 InterNetChProtect Table For inter-network interference reduction factor graphs. Field
Type
Description
Attributes
ICP
Memo
Inter-network channel protection = f( MHz)
Null column allowed: Yes Default value:
ITF_BW
Double
Interfering bandwidth (kHz)
Null column allowed: No Default value: 0
193
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
ITF_TECHNO
Text (50)
Interfering technology
Null column allowed: No Default value:
V_BW
Double
Victim bandwidth (kHz)
Null column allowed: No Default value: 0
7.22 Neighbours Table For intra-technology neighbour relations. Field
Type
Description
Attributes
FORCE_HHO
Boolean
Force Handover type to hard handover in case of intra-carriers neighbours
Null column allowed: No Default value: False
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
7.23 NeighboursConstraints Table For intra-technology neighbour allocation constraints. Field
Type
Description
Attributes
FORCE_HHO
Boolean
Force Handover type to hard handover in case of intra-carriers neighbours
Null column allowed: No Default value: False
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Second part of the unique key. List of neighbours
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells.
Null column allowed: No Default value:
7.24 NeighboursConstraintsExt Table For inter-technology neighbour allocation constraints. Field IMPORTANCE NEIGHBOUR
194
Type Float
Description
Attributes
Handover importance (for AFP use)
Null column allowed: Yes Default value:
Text (50) Second part of the unique key. List of neighbours from another project.
Null column allowed: No Default value:
STATUS
Integer
Type of constraint on the neighbourhood relationship. Constraint is used in automatic allocation. Choice list: 0=Forced; 1=Forbidden;
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
7.25 NeighboursExt Table For inter-technology neighbour relations. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance (for AFP use)
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50) Second part of the unique key. List of neighbours from another project
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
First part of the unique key. Transmitters or cells
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
7.26 Networks Table For network-level parameters. Field
Type
Description
Attributes
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: ‘Cost-Hata’
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
DWPTS_CHIPS_NUMBER
Integer
DwPTS (TS dedicated to the pilot)
Null column allowed: Yes Default value: 96
EBNT_QUALITY_TARGET
Boolean
Type of quality target. True = Eb/Nt, False = C/I
Null column allowed: No Default value: True
FRAME_TIME
Short
Duration of a frame in ms
Null column allowed: Yes Default value: 10
GUARD_PERIOD_CHIPS_NU MBER
Float
Number of chips in guard period
Null column allowed: Yes Default value: 16
HSDPA_NTISNTOT
Boolean
HSDPA only: Nt includes or not pilot's signal for HS-SCCH, HS-PDSCH and CPICH for CQI determination
Null column allowed: No Default value: False
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -130
MIDAMBLE_CHIPS_NUMBER
Float
Number of chips in midamble
Null column allowed: Yes Default value: 144
NAME
Text (50)
NTISNTOT
Boolean
Nt includes pilot signal or not
Null column allowed: No Default value: False
PILOT_PROCESSING_GAIN
Float
P-CCPCH Processing Gain
Null column allowed: Yes Default value: 13.8
POWERS_RELATIVE_TO_PILO T
Boolean
Cell Paging and Synchro powers, Service Allowed DL min and max TCH powers are absolute values (False) or relative to cell pilot power (True)
Null column allowed: No Default value:
PTS_GUARD_PERIOD_CHIPS_ NUMBER
Integer
Number of chips in the PTS guard period
Null column allowed: Yes Default value: 96
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SPREADING_FACTOR_MAX
Integer
Maximum spreading factor
Null column allowed: Yes Default value: 16
Null column allowed: No Default value:
195
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
SPREADING_FACTOR_MIN
Integer
Minimum spreading factor
Null column allowed: Yes Default value: 1
SPREADING_WIDTH
Float
Spreading width (MHz)
Null column allowed: Yes Default value: 1.28
SUBFRAME_TIME
Short
Duration of a subframe in ms
Null column allowed: Yes Default value: 5
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value: ‘TDSCDMA’
TECHNOLOGY
Text (10)
Name of the technology
Null column allowed: No Default value: ‘CDMA’
TS_DATA_CHIPS_NUMBER
Float
Number of data chips in a TS
Null column allowed: Yes Default value: 704
TS_NUMBER
Integer
Number of TS in a subframe
Null column allowed: Yes Default value: 7
UPPTS_CHIPS_NUMBER
Integer
UpPTS (TS dedicated to the pilot)
Null column allowed: Yes Default value: 160
7.27 PropagationModels Table For propagation models. Field
Type
Description
Attributes
Data
Binary
Model specific parameters
Null column allowed: Yes Default value:
Description
Text (255)
User defined
Null column allowed: Yes Default value:
Name
Text (50)
Name of the propagation model
Null column allowed: No Default value:
Signature
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
Type
Text (50)
ProgID of the model
Null column allowed: No Default value:
7.28 QualityIndicators Table For quality indicators (BER, BLER, etc.). Field
Type
Attributes
CS_QI
Boolean
Flag which indicates if this indicator is used in CS services
Null column allowed: No Default value: True
MEAS_PARAM
Short
Name of the measured figure used for this QI determination Choice list: 1=CPICH_ECIO; 2=CPICH_CI; 3=CPICH_ECNT; 4=DCH_EBNT; 5=HSPDSCH_ECNT;
Null column allowed: Yes Default value: 1
NAME
Text (20)
Name of the managed quality indicator
Null column allowed: No Default value:
PS_QI
Boolean
Flag which indicates if this indicator is used for PS services
Null column allowed: No Default value: True
USE_INTERPOLATION
Boolean
Flag which indicates if this QI must be interpolated or not
Null column allowed: No Default value: True
7.29 R99Bearers Table For release 99 bearers.
196
Description
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
DL_NOMINAL_BIT_RATE
Float
Bearer nominal data rate on the downlink Unit: kbps
Null column allowed: Yes Default value: 9.6
DL_PG
Float
Downlink processing gain
Null column allowed: Yes Default value: 0
NAME
Text (50)
R99 bearer name
Null column allowed: No Default value:
PTCH_MAX
Float
Maximum DL transmitter power on traffic channel for the bearer
Null column allowed: Yes Default value: 21
PTCH_MIN
Float
Minimum DL transmitter power on traffic channel for the bearer
Null column allowed: Yes Default value: -20
TS_DL
Short
Number of TS used for DL
Null column allowed: Yes Default value: 1
TS_UL
Short
Number of TS used for UL
Null column allowed: Yes Default value: 1
TYPE
Short
Bearer type (0: Empty, 1: Interactive, 2: Conversational, 3: Background ,4: Streaming)
Null column allowed: Yes Default value: 0
UL_NOMINAL_BIT_RATE
Float
Bearer nominal data rate on the uplink Unit: kbps
Null column allowed: Yes Default value: 9.6
UL_PG
Float
Uplink processing gain
Null column allowed: Yes Default value: 0
7.30 Receivers Table For receiver parameters. Field
Type
Description
Attributes
ADJ_CHANNEL_PROT
Float
Protection against interfering signals from adjacent channels.
Null column allowed: No Default value: 18
ANTENNA
Text (50)
Receiver antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the receiver
Null column allowed: No Default value: 1.5
LOSS
Float
Losses due to receiver radio equipment (up and downlink)
Null column allowed: No Default value: 0
NAME
Text (50)
Receiver name
Null column allowed: No Default value:
7.31 RepeaterEquipments Table For repeater equipment. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
MANUFACTURER
Text (50)
Manufacturer of the repeater equipment
Null column allowed: Yes Default value:
MAX_AMPLIFIER_GAIN
Float
Maximum gain of the amplifier (dB)
Null column allowed: Yes Default value: 90
MAX_OUTPUT_DL
Float
Maximum downlink output power (dBm)
Null column allowed: Yes Default value: 30
MAX_OUTPUT_UL
Float
Maximum uplink output power (dBm)
Null column allowed: Yes Default value: 12
MIN_AMPLIFIER_GAIN
Float
Minimum gain of the amplifier (dB)
Null column allowed: Yes Default value: 50
197
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
NAME
Text (50)
Name of the repeater equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Repeater noise Figure (dB)
Null column allowed: Yes Default value: 5
STEP_AMPLIFIER_GAIN
Float
Step of amplifier gain (dB)
Null column allowed: Yes Default value: 1
TIME_DELAY
Float
Time delay in the equipment (microseconds)
Null column allowed: Yes Default value: 5
7.32 Repeaters Table For repeaters. Field
Type
Description
Attributes
AMPLIFIER_GAIN
Float
Gain of the amplifier
Null column allowed: Yes Default value: 80
AZIMUT
Float
Azimuth of the donor side antenna
Null column allowed: Yes Default value: 0
DONOR_CELLID
Text (50)
Name of the donor cell
Null column allowed: No Default value:
DONOR_LINK_LOSS
Float
Loss (dB) between donor and donor side of the repeater
Null column allowed: Yes Default value: 0
DONOR_LINK_TYPE
Short
1- Off air 2- Microwave 3- Fibre
Null column allowed: No Default value: 1
DONOR_PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction between donor and repeater
Null column allowed: Yes Default value:
DOWNTILT
Float
Downtilt of the donor side antenna
Null column allowed: Yes Default value: 0
EQUIPMENT_NAME
Text (50)
If no equipment, the repeater is a passive component
Null column allowed: Yes Default value:
FEEDER_NAME
Text (50)
Name of the donor side feeder
Null column allowed: Yes Default value:
FEEDERLENGTH
Float
Length of donor side feeder
Null column allowed: Yes Default value: 0
HEIGHT
Float
Height of the donor side antenna
Null column allowed: Yes Default value: 25
REC_ANTENNA
Text (50)
Name of the donor side antenna
Null column allowed: Yes Default value:
REC_FEEDERLENGTH_UL
Float
Length of donor side uplink feeder
Null column allowed: Yes Default value: 0
TOTAL_GAIN
Float
Total gain to be applied to donor cell pilot power
Null column allowed: Yes Default value: 0
TOTAL_GAIN_UL
Float
Uplink total gain to be applied to mobile output power
Null column allowed: Yes Default value: 0
TX_ID
Text (50)
Name of the repeater (and of the transmitter used for coverage)
Null column allowed: No Default value:
Repeater properties are saved in two tables: the donor-side parameters are in the Repeaters table and the coverage-side parameters in the Transmitters table.
7.33 SACIGainCDF Table For CDF graphs of smart antenna C/I gains.
198
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
ANGULAR_SPREAD
Short
Value of the average angular spread in dB
Null column allowed: Yes Default value: 5
CIGAIN_CDF
Memo
CDF of C/I gain values (list of pairs: C/I, cumulated probability)
Null column allowed: Yes Default value:
SA_NAME
Text (50)
Name of the Smart antenna
Null column allowed: No Default value:
7.34 ScramblingCodesDomains Table For names of scrambling code domains. Field
Type
DOMAIN_NAME
Text (50)
Description
Attributes
Resource domain name
Null column allowed: No Default value:
7.35 ScramblingCodesGroups Table For scrambling code groups belonging to scrambling code domains. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Second part of the unique key. Called grouping scheme. Set of scrambling code groups.
Null column allowed: No Default value:
EXCLUDED
Text (225)
List of codes to be excluded from the series defined by FIRST, LAST and STEP (separated by blank characters)
Null column allowed: Yes Default value:
EXTRA
Text (225)
Codes to be added. It is forbidden for EXTRA and EXLUDED to have common numbers. Separator must be a blank character.
Null column allowed: Yes Default value:
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
First part of the unique key. Name of the scrambling code group
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
7.36 SecondaryAntennas Table For additional antennas. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna installed on the transmitter
Null column allowed: No Default value:
AZIMUT
Float
Second part of the unique key. Azimuth of the antenna
Null column allowed: No Default value: 0
PERCENT_POWER
Float
Percentage of power dedicated to the secondary antenna
Null column allowed: No Default value: 0
REDT
Float
Additional electrical downtilt
Null column allowed: Yes Default value: 0
TILT
Float
Mechanical downtilt of the secondary antenna
Null column allowed: No Default value: 0
TX_ID
Text (50)
First part of the unique key. Transmitter name
Null column allowed: No Default value:
199
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
7.37 Separations Table For scrambling code allocation constraints. Field
Type
Description
Attributes
TX_ID
Text (50)
First part of the unique key. First cell name in a symmetric relation
Null column allowed: No Default value:
TX_ID_OTHER
Text (50)
Second part of the unique key. Second cell name in a symmetric relation
Null column allowed: No Default value:
7.38 ServiceQualityTables Table For release 99 performance graphs. Field
Type
Description
Attributes
DL_QI_TABLE
Memo
QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
MOBILITY
Text (50)
UE mobility
Null column allowed: Yes Default value:
QI_NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Type of receiver of the User Equipment
Null column allowed: No Default value: ’Standard’
SERVICE
Text (50)
Name of the service (can be null for some QI)
Null column allowed: No Default value:
UL_QI_TABLE
Memo
QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
7.39 ServiceRUsUse Table For resource unit consumptions per service. Field
Type
Description
Attributes
DIRECTION
Short
Uplink or downlink Choice list: 1=DL; 2=UL;
Null column allowed: No Default value: 1
NB_SF1
Short
Number of SF1 codes allocated for DL
Null column allowed: Yes Default value: 0
NB_SF16
Short
Number of SF16 codes allocated for DL
Null column allowed: Yes Default value: 1
NB_SF2
Short
Number of SF2 codes allocated for DL
Null column allowed: Yes Default value: 0
NB_SF4
Short
Number of SF4 codes allocated for DL
Null column allowed: Yes Default value: 0
NB_SF8
Short
Number of SF8 codes allocated for DL
Null column allowed: Yes Default value: 0
SERVICE
Text (50)
Service name
Null column allowed: No Default value:
TS_RANK
Short
Rank for TS allocation in Monte Carlo simulations
Null column allowed: No Default value: 1
7.40 Sites Table For sites.
200
Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude Unit: m
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
CDMA_EQUIPMENT
Text (50)
Equipment associated with the site
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information on the site
Null column allowed: Yes Default value:
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
7.41 SitesLists Table For sites belonging to site lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list
Null column allowed: No Default value:
SITE_NAME
Text (50)
Second part of the unique key. Name of the site
Null column allowed: No Default value:
7.42 SitesListsNames Table For names of site lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
7.43 SmartAntennas Table For smart antenna equipment. Field
Type
Description
Attributes
ADAPTIVE_PATTERN_DL
Text (50)
Downlink pattern used to model an adaptative smart antenna
Null column allowed: Yes Default value:
ADAPTIVE_PATTERN_UL
Text (50)
Uplink pattern used to model an adaptative smart antenna
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Algorithm used to the C/I gain curves
Null column allowed: Yes Default value:
ELTS_NUMBER
Integer
Number of elements
Null column allowed: Yes Default value: 4
GEOMETRY_TYPE
Integer
Geometry 1- ULA 2- UCA
Null column allowed: Yes Default value: 1
GOB_PATTERN
Text (50)
Downlink grid of beams name
Null column allowed: Yes Default value:
GOB_PATTERN_UL
Text (50)
Uplink grid of beams name
Null column allowed: Yes Default value:
INTER_ELTS_DIST
Integer
Distance between elements in % of the wavelength
Null column allowed: Yes Default value: 50
201
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MODELLING_TYPE
Short
NAME
Text (50)
Name of the Smart Antenna
Null column allowed: No Default value:
PROBA_THRESHOLD
Integer
Probability of having more than used C/I gain
Null column allowed: Yes Default value: 50
SA_MODEL
Text (50)
External Model used to model the smart antenna
Null column allowed: Yes Default value:
Modelling Type: 0- Dedicated Model, 1- Ideal Beam Steering, 2- Grid Of Null column allowed: Yes Beams, 3- Statistical Default value: 0
7.44 SmartAntennasModels Table For smart antenna models. Field
Type
Description
Attributes
SA_DATA
Binary
Smart antenna model data
Null column allowed: Yes Default value:
SA_DESCRIPTION
Text (50)
Description of the smart antenna model
Null column allowed: Yes Default value:
SA_NAME
Text (50)
Name of the smart antenna model
Null column allowed: No Default value:
SA_SIGNATURE
Text (50)
Signature of the smart antenna model
Null column allowed: No Default value:
SA_TYPE
Text (50)
Type of the smart antenna model
Null column allowed: No Default value:
7.45 TMAEquipments Table For tower-mounted amplifiers. Field
Type
Description
Attributes
DL_LOSSES
Float
Downlink losses of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Tower Mounted Amplifier
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
UL_GAIN
Float
Uplink gain of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
7.46 TplTransmitters Table For station templates.
202
Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value:
ANTDIVGAIN
Float
Antenna diversity gain Unit: dB
Null column allowed: Yes Default value:
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: No Default value:
AZIMUT
Float
Azimuth of the first antenna
Null column allowed: Yes Default value:
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
CALC_RADIUS
Integer
Calculation radius used to define each transmitter calculation area Unit: m
Null column allowed: Yes Default value:
CALC_RADIUS2
Integer
Extended calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value:
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CARRIERS
Text (50)
Carriers used by the transmitter
Null column allowed: Yes Default value:
CDMA_EQUIPMENT
Text (50)
CDMA equipment
Null column allowed: Yes Default value:
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value:
DWPCH_POWER
Float
Power on the DwPTS timeslot
Null column allowed: Yes Default value:
DYN_EDCH_DL_POWER_ALL OC
Boolean
Allocation of power for HSUPA DL power (E-AGCH, E-HICH): True=Dynamic; False=Static;
Null column allowed: No Default value:
DYN_HS_SCCH_POWER_ALL OC
Boolean
Allocation of power for HS_SCCH (True=Dynamic, False=Static)
Null column allowed: No Default value:
DYN_HS_SICH_POWER_ALLO C
Boolean
Allocation of power for HS-SICH (True=Dynamic, False=Static)
Null column allowed: No Default value:
DYN_HSDPA_POWER_ALLOC
Boolean
Allocation of power for HSDPA (True=Dynamic, False=Static)
Null column allowed: No Default value:
EDCH_DL_POWER
Float
Value of power dedicated to E-AGCH and E-HICH channel per timeslot. In case of dynamic allocation, it is the maximum available power.
Null column allowed: Yes Default value:
FBAND
Text (50)
Frequency band
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value:
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value:
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value:
HS_SCCH_POWER
Float
Value of power dedicated to a HS_SCCH channel. In case of dynamic allocation, it is the maximum available power.
Null column allowed: Yes Default value:
HSDPA_MAX_CODES
Short
Maximum number of HS-PDSCH codes
Null column allowed: Yes Default value:
HSDPA_MAX_USERS
Short
Max number of HSDPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value:
HSDPA_MIN_CODES
Short
Minimum Number of HS-PDSCH codes
Null column allowed: Yes Default value:
HSDPA_PWR
Float
Amount of power (dBm) dedicated to HSDPA
Null column allowed: Yes Default value:
HSDPA_SCHEDULER_ALGO
Short
Scheduling algo used for HSDPA users. 0=MAXC/I (MAx C/I), 1=RR (Round Robin), 2=PF (Proportional Fair)
Null column allowed: Yes Default value:
HSPA_SUPPORT
Short
HSPA features supported: 0=None; 1=HSDPA; 2=HSPA;
Null column allowed: Yes Default value:
203
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
HSUPA_MAX_USERS
Integer
Max number of HSUPA users managed simultaneously by the scheduler
Null column allowed: Yes Default value:
MAX_EXT_NEIGHB_NUMBER
Short
Maximum number of inter-technology neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Short
Maximum number of neighbours for the cell or the transmitter
Null column allowed: Yes Default value:
MAX_R99BEARER_DL_RATE
Float
Max bearer rate available in DL (kbps)
Null column allowed: Yes Default value:
MAX_R99BEARER_UL_RATE
Float
Max bearer rate available in UL (kbps)
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value:
MIN_RANGE
Integer
Minimum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous downlink losses
Null column allowed: Yes Default value:
MISCULL
Float
Miscellaneous uplink losses
Null column allowed: Yes Default value:
N_FREQUENCY
Boolean
N-frequency mode. 'Yes' means that the transmitter has one master carrier and slaves carriers; otherwise all its carriers are standalone
Null column allowed: No Default value:
NAME
Text (50)
Template name
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value:
NUM_HS_SCCH
Short
Number of HS_SCCH channels
Null column allowed: Yes Default value:
NUM_HS_SICH
Short
Number of HS-SICH channels per cell
Null column allowed: Yes Default value:
NUM_HSDPA_USERS
Integer
Number of served HSDPA users in the cell: calculated by the TD-SCDMA Null column allowed: Yes simulation algorithm Default value:
NUM_HSUPA_USERS
Integer
Number of served HSUPA users in the cell: calculated by the TD-SCDMA Null column allowed: Yes simulation algorithm Default value:
NUM_RX_ANTENNAS
Short
Number of transmission antenna ports available at the transmitter
Null column allowed: Yes Default value:
NUM_SECTORS
Integer
Number of sectors
Null column allowed: Yes Default value: 3
NUM_TX_ANTENNAS
Short
Number of reception antenna ports available at the transmitter
Null column allowed: Yes Default value:
OTHERS_CCH_POWER
Float
Power of common channels (except SCH)
Null column allowed: Yes Default value:
PILOT_POWER
Float
Power of the pilot channel
Null column allowed: Yes Default value:
POWER_MAX
Float
Maximum power supported by the transmitter
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate predictions
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
PWR_HEADROOM
Float
Power Control Headroom (dB) for DCH (used in WCDMA simulation algorithm)
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value:
REQ_DL_RUS
Integer
Required resource units in downlink
Null column allowed: Yes Default value:
204
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
REQ_UL_RUS
Integer
Required resource units in uplink
Null column allowed: Yes Default value:
REUSE_DIST
Float
Minimum reuse distance for scrambling codes
Null column allowed: Yes Default value:
RSCP_MIN
Float
Min RSCP reception level (dBm)
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses in the uplink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
SA_NAME
Text (50)
SC_DOMAIN_NAME
Text (50)
Scrambling code domain name
Null column allowed: Yes Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value:
TILT
Float
Mechanical downtilt of the main antenna
Null column allowed: Yes Default value:
TMA_NAME
Text (50)
Name of the Tower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TS_CONFIG
Float
Timeslot configuration (1-DUDDDDD 2-DUUDDDD 3-DUUUDDD 4DUUUUDD 5-DUUUUUD 6-DUUUUUU)
Null column allowed: Yes Default value:
TX_DIVERSITY_CFG
Integer
TX diversity configuration 0=No TX diversity; 1=TX div. open loop; 2=TX div. closed loop
Null column allowed: Yes Default value:
TXLOSSES
Float
Losses in the downlink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value:
Name of the associated smart antenna (if empty, the standard antenna Null column allowed: Yes is used) Default value:
7.47 Transmitters Table For transmitters. Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value: True
ANTDIVGAIN
Float
Antenna diversity gain
Null column allowed: Yes Default value: 0
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the main antenna
Null column allowed: Yes Default value: 0
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define the calculation area Unit: m
Null column allowed: Yes Default value: 4000
CALC_RADIUS2
Integer
Extended calculation radius
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value: 50
CALC_RESOLUTION2
Integer
Extended calculation resolution
Null column allowed: Yes Default value:
CELL_SIZE
Float
Hexagon radius Unit: m
Null column allowed: Yes Default value: 2000
205
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
206
© Forsk 2014
Field
Type
Description
Attributes
COMMENT_
Text (255)
Additional information about the transmitter
Null column allowed: Yes Default value:
DX
Float
X coordinate relative to the site location
Null column allowed: Yes Default value: 0
DY
Float
Y coordinate relative to the site location
Null column allowed: Yes Default value: 0
FBAND
Text (50)
Frequency band
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of feeder in DL
Null column allowed: Yes Default value: 0
FEEDERLENGTH_UL
Float
Length of feeder in UL
Null column allowed: Yes Default value: 0
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value: 25
HEXAGON_GROUP
Text (50)
Group of hexagons used to create this transmitter
Null column allowed: Yes Default value:
MAX_RANGE
Integer
Maximum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value: 35000
MIN_RANGE
Integer
Minimum range (m) of coverage (for extended cells)
Null column allowed: Yes Default value: 0
MISCDLL
Float
Miscellaneous DL loss
Null column allowed: Yes Default value: 0
MISCULL
Float
Miscellaneous UL loss
Null column allowed: Yes Default value: 0
N_FREQUENCY
Boolean
N-frequency mode. 'Yes' means that the transmitter has one master carrier and slaves carriers; otherwise all its carriers are standalone
Null column allowed: No Default value: False
NOISE_FIGURE
Float
Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
NUM_RX_ANTENNAS
Short
Number of transmission antenna ports available at the transmitter
Null column allowed: No Default value: 1
NUM_TX_ANTENNAS
Short
Number of reception antenna ports available at the transmitter
Null column allowed: No Default value: 1
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value: ’Default model’
PROPAG_MODEL2
Text (255)
Name of the propagation model used to calculate extended prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value: 0
RXLOSSES
Float
Losses in the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
SA_NAME
Text (50)
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SITE_NAME
Text (50)
Name of the site on which the transmitter is located (from the Sites table)
Null column allowed: No Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
TILT
Float
Mechanical downtilt of the first antenna
Null column allowed: Yes Default value: 0
TMA_NAME
Text (50)
Name of the TMA equipment
Null column allowed: Yes Default value:
Name of the associated smart antenna (if empty, the standard antenna Null column allowed: Yes is used) Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
TX_DIVERSITY_CFG
Short
TX diversity configuration. 1 = No TX diversity 2 = TX div. open loop 3 = TX div. closed loop
Null column allowed: Yes Default value: 0
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
TXLOSSES
Float
Losses in the downlink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
7.48 TxsLists Table For transmitters belonging to transmitter lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list.
Null column allowed: No Default value:
TX_NAME
Text (50)
Second part of the unique key. Name of the transmitter.
Null column allowed: No Default value:
7.49 TxsListsNames Table For names of transmitter lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the transmitter list
Null column allowed: No Default value:
7.50 UECategories Table For HSDPA UE categories. Field
Type
Description
Attributes
MAX_BLOCK_SIZE
Integer
Maximum transport block size supported (bits)
Null column allowed: Yes Default value: 26000
MAX_HSPDSCH_NUM
Short
Maximum number of HS-PDSCH channels for HSDPA
Null column allowed: Yes Default value: 5
MAX_HSPDSCH_TS
Short
Maximum number of HS-PDSCH time slots per TTI
Null column allowed: Yes Default value: 2
MODULATION
Short
Modulation (0: QPSK; 1: 16QAM)
Null column allowed: No Default value: 0
UE_CATEGORY
Short
UE category for HSDPA
Null column allowed: No Default value:
UE_CATEGORY_NAME
Text (50)
Name of the HSDPA UE category
Null column allowed: Yes Default value:
7.51 UERxEquipments Table For UE reception equipment. Field
Type
Description
Attributes
NAME
Text (50)
Name of the type of receiver in the UE
Null column allowed: No Default value:
7.52 UMTSEnvironmentDefs Table For traffic environment types.
207
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DENSITY
Float
Number of subscribers per km2
Null column allowed: Yes Default value: 0
ENVIRONMENT
Text (50)
Environment name
Null column allowed: No Default value:
MOBILITY
Text (50)
Type of mobility
Null column allowed: No Default value:
USER_PROFILE
Text (50)
Type of user profile
Null column allowed: No Default value:
7.53 UMTSMobility Table For mobility types. Field
Type
Description
Attributes
DWPCH_QUALITY
Float
Quality target for the DwPCH (dB)
Null column allowed: Yes Default value: 2
DWPCH_RSCP
Float
Minimum DwPCH RSCP (dBm)
Null column allowed: Yes Default value: -100
EDCH_DL_ECNT
Float
E-DCH Ec/Nt target for HSUPA DL power (E-AGCH, E-HICH)
Null column allowed: Yes Default value: -12
HSSCCH_ECNT
Float
HS-SCCH Ec/Nt target for HSDPA
Null column allowed: Yes Default value: -12
HSSICH_ECNT
Float
HS-SICH uplink Ec/Nt target for HSDPA
Null column allowed: Yes Default value: -12
MEAN_SPEED
Float
Mean mobile speed (km/h) used for HSDPA
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of mobility
Null column allowed: No Default value:
RSCP_DROP
Float
P-CCPCH RSCP for cell dropping (Baton Handover)
Null column allowed: Yes Default value: -95
RSCP_MIN
Short
Minimum P-CCPCH RSCP for cell selection (dBm)
Null column allowed: Yes Default value: -84
TADD
Float
Minimum Ec/Io for best server selection
Null column allowed: Yes Default value: 7
UPPCH_RSCP
Float
Minimum UpPCH RSCP (dBm)
Null column allowed: Yes Default value: -100
7.54 UMTSServices Table For services.
208
Field
Type
Description
Attributes
ADPCH_ACTIVITY
Float
Activity Factor for HSDPA users
Null column allowed: Yes Default value: 0.1
BODY_LOSS
Float
Body loss
Null column allowed: No Default value: 0
CARRIER_LIST
Text (50)
List of preferred carrier numbers
Null column allowed: Yes Default value:
CARRIER_SUPPORT
Integer
Carrier support type: 0=Prefered; 1=Allowed;
Null column allowed: Yes Default value: 0
DL_ACTIVITY
Float
Activity factor for circuit switched service on the downlink
Null column allowed: Yes Default value: 1
DL_DP
Float
Packet inter arrival time (ms) on the downlink
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
DL_DPC
Float
Reading time (distance) between two packet calls (ms) on the downlink
Null column allowed: Yes Default value: 0
DL_NPC
Integer
Number of packet calls during a session on the downlink
Null column allowed: Yes Default value: 1
DL_PACKET_EFFICIENCY
Float
Packet efficiency factor on the downlink
Null column allowed: Yes Default value:
DL_SP
Integer
Packet size (Bytes) on the downlink
Null column allowed: Yes Default value: 1500
DL_SPC_MAX
Float
Downlink max Packet call size (kBytes)
Null column allowed: Yes Default value: 2000
DL_SPC_MIN
Float
Downlink min Packet call size (kBytes)
Null column allowed: Yes Default value: 4
EDPCH_ACTIVITY
Float
Activity Factor for HSUPA users
Null column allowed: Yes Default value: 0.1
NAME
Text (50)
Service name
Null column allowed: No Default value:
PRIORITY
Integer
Priority level of the service: parameter used in the WCDMA simulation
Null column allowed: Yes Default value: 0
R99BEARER
Text (50)
Name of the R99 Bearer
Null column allowed: Yes Default value:
REQ_AVERAGE_DL_RATE
Float
Requested Average Downlink Rate (kbps)
Null column allowed: Yes Default value:
REQ_AVERAGE_UL_RATE
Float
Requested Average Uplink Rate (kbps)
Null column allowed: Yes Default value:
REQ_MIN_DL_RATE
Float
Requested Minimum Downlink Rate (kbps)
Null column allowed: Yes Default value: 0
REQ_MIN_UL_RATE
Float
Requested Minimum Uplink Rate (kbps)
Null column allowed: Yes Default value: 0
TH_OFFSET
Float
Offset to add to the above ratio
Null column allowed: No Default value: 0
TH_SCALE_FACTOR
Float
Ratio between application throughput and RLC layer throughput
Null column allowed: No Default value: 95
TYPE
Short
Type of service (0: circuit; 1: packet; 2: circuit over packet)
Null column allowed: No Default value: 0
UL_ACTIVITY
Float
Activity factor for circuit switched service on the uplink
Null column allowed: Yes Default value: 1
UL_DP
Float
Packet inter arrival time (ms) on the uplink
Null column allowed: Yes Default value: 0
UL_DPC
Float
Reading time (distance) between two packet calls (ms) on the uplink
Null column allowed: Yes Default value: 0
UL_NPC
Integer
Number of packet calls during a session on the uplink
Null column allowed: Yes Default value: 1
UL_PACKET_EFFICIENCY
Float
Packet efficiency factor on the uplink
Null column allowed: Yes Default value:
UL_SP
Integer
Packet size (Bytes) on the uplink
Null column allowed: Yes Default value: 1500
UL_SPC_MAX
Float
Uplink max Packet call size (kBytes)
Null column allowed: Yes Default value: 2000
UL_SPC_MIN
Float
Uplink min Packet call size (kBytes)
Null column allowed: Yes Default value: 4
7.55 UMTSServicesQuality Table For release 99 service access thresholds.
209
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DL_TARGET_QUAL
Float
Eb/Nt target on the downlink for a type of mobility
Null column allowed: Yes Default value: 0
DL_TGT_QUAL_DIVCLOSED
Float
Quality target on downlink in case of closed loop TX diversity
Null column allowed: Yes Default value: 0
DL_TGT_QUAL_DIVOPEN
Float
Quality target on downlink in case of open loop TX diversity
Null column allowed: Yes Default value: 0
MOBILITY
Text (50)
Second part of the unique key. Type of mobility
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Type of receiver
Null column allowed: No Default value:
SERVICE
Text (50)
First part of the unique key. Name of the service
Null column allowed: No Default value:
TCH_THRESHOLD_DL
Short
RSCP TCH target on downlink for a type of mobility
Null column allowed: Yes Default value: 0
TCH_THRESHOLD_UL
Short
RSCP TCH target on uplink for a type of mobility
Null column allowed: Yes Default value: 0
UL_TARGET_QUAL
Float
Eb/Nt target on the uplink for a type of mobility
Null column allowed: Yes Default value: 0
UL_TGT_QUAL_DIV2RX
Float
Quality target on uplink in case of 2RX diversity
Null column allowed: Yes Default value: 0
UL_TGT_QUAL_DIV4RX
Float
Quality target on uplink in case of 4RX diversity
Null column allowed: Yes Default value: 0
7.56 UMTSServicesUsage Table For user profile parameters. Field
Type
Description
Attributes
CALL_DURATION
Float
Average duration of a call (for circuit switched services) Unit: s
Null column allowed: Yes Default value:
CALL_NUMBER
Float
Average number of calls per hour for circuit switched services or average number of sessions per hour for packet switched services
Null column allowed: Yes Default value: 0
DL_VOLUME
Float
Data volume transferred on the downlink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
SERVICE
Text (50)
Service that the subscriber can request
Null column allowed: No Default value:
TERMINAL
Text (50)
Type of terminal used by the subscriber for the service
Null column allowed: No Default value:
UL_VOLUME
Float
Data volume transferred on the uplink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
USER_PROFILE
Text (50)
User profile name
Null column allowed: No Default value:
7.57 UMTSTerminals Table For terminal types.
210
Field
Type
Description
Attributes
CARRIER_NUMBER
Short
Number of carriers supported by the terminal
Null column allowed: Yes Default value: 1
GAIN
Float
Receiver antenna gain
Null column allowed: Yes Default value: 0
HSPA_SUPPORT
Short
HSPA features supported: 0=None; 1=HSDPA; 2=HSPA
Null column allowed: No Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
HSSICH_POWER
Float
Maximum power on HS-SICH channels
Null column allowed: Yes Default value: 21
HSUPA_UE_CATEGORY
Short
HSUPA UE category
Null column allowed: Yes Default value: 1
LOSS
Float
Receiver antenna loss
Null column allowed: Yes Default value: 0
MUD_FACTOR
Float
NAME
Text (50)
Terminal name
Null column allowed: No Default value:
NOISE_FACTOR
Float
Noise figure used to determine the thermal noise at the receiver
Null column allowed: Yes Default value: 8
PMAX
Float
Maximum receiver power on traffic channel
Null column allowed: Yes Default value: 21
PMIN
Float
Minimum receiver power on traffic channels
Null column allowed: Yes Default value: -50
RHO_FACTOR
Short
Rho factor to model self generated interference
Null column allowed: No Default value: 100
RX_EQUIP
Text (50)
Type of the User Equipment Receiver
Null column allowed: Yes Default value: ‘Standard’
UE_CATEGORY
Float
Category of the User Equipment for HSDPA
Null column allowed: Yes Default value: 1
UPPCH_POWER
Float
Power on the UpPTS timeslot
Null column allowed: Yes Default value: -50
Advanced Receiver Factor to model intra-cell interference reduction for Null column allowed: Yes HSDPA terminals only Default value: 0
7.58 UMTSTraficEnvironments Table For traffic environment clutter weighting. Field
Type
Description
Attributes
CLUTTER_WEIGHTS
Binary
Internal binary format describing weights assigned to each clutter class
Null column allowed: Yes Default value: Yes
NAME
Text (50)
Name of the created environment
Null column allowed: No Default value:
7.59 UMTSUserProfiles Table For names of user profiles. Field
Type
Description
Attributes
NAME
Text (50)
Name of the created user profile
Null column allowed: No Default value:
7.60 Units Table For the reception and transmission units, the projection coordinate system specified in the ATL document, and the database internal coordinate system. Field
Type
Description
Attributes
COORD_SYSTEM
Integer
Display coordinate system when creating database
Null column allowed: Yes Default value: -1
GAIN_UNIT
Integer
Unit used for gains (dBd or dBi) Choice list: 0=dBd; 1=dBi;
Null column allowed: Yes Default value: 0
PROJECTION
Integer
Projected coordinate system for geo data
Null column allowed: Yes Default value: -1
211
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
© Forsk 2014
Field
Type
Description
Attributes
RECEPTION_UNIT
Integer
Reception unit when creating database Choice list: 0=dBm; 1=dbµV; 2=dbµV/m;
Null column allowed: No Default value: 0
TRANSMISSION_UNIT
Integer
Transmission unit when creating database Choice list: 0=dBm; 1=Watts; 2=kWatts;
Null column allowed: No Default value: 0
212
AT321_DSR_E1
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
213
Atoll 3.2.1 Data Structure Reference Guide Chapter 7: TD-SCDMA Data Structure
214
© Forsk 2014
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
8 WiMAX and Wi-Fi Data Structure Figure 8.1 on page 215, Figure 8.2 on page 216, and Figure 8.3 on page 217 depict the WiMAX BWA database structure. The following subsections list the tables in the WiMAX BWA template data structure.
Figure 8.1: WiMAX BWA Template - 1
215
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Figure 8.2: WiMAX BWA Template - 2
216
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Figure 8.3: WiMAX BWA Template - 3
8.1 Data Structure Changes Between Atoll 3.1 and 3.2 8.1.1 Added Tables and Fields Antennas Table Field
Type
ELECTRICAL_AZIMUTH
Float
Description
Attributes
Antenna electrical azimuth
Null column allowed: Yes Default value:
CustomFields Table Field
Type
DISPLAY_TYPE
Integer
Description
Attributes
0: Field is modifiable; 1: Field is read-only
Null column allowed: Yes Default value: 0
FrameConfigurations Table Field CYCLIC_PREFIX
Type Short
Description
Attributes
Cyclic prefix ratio (NULL; 0: 1/4; 1: 1/8; 2: 1/16; 4: 1/32)
Null column allowed: Yes Default value:
217
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
FrequencyBands Table Field
Type
Description
Attributes
DELTA_CN
Integer
Step between two adjacent channel numbers
Null column allowed: Yes Default value: 1
Networks Table Field
Type
Description
Attributes
MIMO_INT_PWR_COMB
Short
Whether interfering signals are combined over multiple antennas or not
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
MAX_BH_RATE_DL
Float
Backhaul maximum DL throughput (kbps)
Null column allowed: Yes Default value: 950000
MAX_BH_RATE_UL
Float
Backhaul maximum UL throughput (kbps)
Null column allowed: Yes Default value: 950000
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
Sites Table
TplTransmitters Table Field
Type
Description
Attributes
LAYER_LIST
Text (255)
List of layers
Null column allowed: Yes Default value: 0
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
Transmitters Table Field
Type
Description
Attributes
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
WCCHDivGains Table (New) Field
Type
Description
Attributes
EQUIPMENT
Text (50)
Name of the reception equipment to which the control channel diversity gains correspond
Null column allowed: No Default value:
MIMO_RX_ANTENNAS
Short
Number of reception antennas used for MIMO
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of transmission antennas used for MIMO
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
Name of the mobility type to which the control channel diversity gains correspond
Null column allowed: Yes Default value:
PREAMBLE_DIV_GAIN
Float
Preamble diversity gain
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
CELL_PERMBASE
Short
Cell PermBase
Null column allowed: Yes Default value: 0
NUM_DL_USERS
Float
Number of DL connected users for the cell
Null column allowed: Yes Default value: 1
NUM_UL_USERS
Float
Number of UL connected users for the cell
Null column allowed: Yes Default value: 1
WCells Table
218
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
SEGMENT
Short
Cell segment
Null column allowed: Yes Default value: 0
WLayers Table (New) Field
Type
Description
Attributes
LAYER_INDEX
Short
Index of the network layer
Null column allowed: No Default value: 0
MAX_SPEED
Float
Maximum speed of mobiles for this layer
Null column allowed: Yes Default value: 300
NAME
Text (50)
Name of the network layer
Null column allowed: No Default value:
PRIORITY
Short
Priority of the network layer
Null column allowed: No Default value: 0
SELECTION_MARGIN
Float
Margin with respect to the highest signal level within which the layer is Null column allowed: Yes candidate for selection as server Default value: 0
WMimoConfigs Table Field
Type
Description
Attributes
MUMIMO_DIV_GAIN
Float
Diversity gain applicable with MU-MIMO
Null column allowed: Yes Default value: 0
SUMIMO_DIV_GAIN
Float
Diversity gain applicable with SU-MIMO
Null column allowed: Yes Default value: 0
WServices Table Field
Type
Description
Attributes
MIN_SC_UL
Integer
Minimum number of required subchannels for the service
Null column allowed: Yes Default value: 1
SUPPORTED_LAYER_LIST
Text (50)
List of network layers on which the service is allowed
Null column allowed: No Default value: “-1”
WTerminals Table Field
Type
Description
Attributes
SUPPORTED_LAYER_LIST
Text (50)
List of network layers supported by the terminal
Null column allowed: No Default value: “-1”
8.1.2 Deleted Tables and Fields Sites Table •
SUPPORT_NATURE
8.2 Antennas Table For antennas. Field
Type
Description
Attributes
Beamwidth
Float
Antenna beamwidth
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the antenna
Null column allowed: Yes Default value:
CONSTRUCTOR
Text (255)
Antenna manufacturer name
Null column allowed: Yes Default value:
219
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DIAGRAM
Binary
Internal binary format containing the description of the antenna horizontal and vertical patterns
Null column allowed: Yes Default value:
ELECTRICAL_AZIMUTH
Float
Antenna electrical azimuth
Null column allowed: Yes Default value:
ELECTRICAL_TILT
Float
Antenna electrical tilt
Null column allowed: Yes Default value:
FMax
Double
Maximum frequency of created antenna Unit: MHz
Null column allowed: Yes Default value:
FMin
Double
Minimum frequency of created antenna Unit: MHz
Null column allowed: Yes Default value:
GAIN
Float
Antenna isotropic gain Unit: dBi
Null column allowed: No Default value: 0
NAME
Text (50)
Name of antenna created in the current project
Null column allowed: No Default value:
PHYSICAL_ANTENNA
Text (50)
Physical antenna name
Null column allowed: Yes Default value:
The format of the binary field, DIAGRAM, is described in "RF 2D Antenna Pattern Format" on page 275.
8.3 BTSEquipments Table For BTS equipment. Field
Type
Description
Attributes
CONFIG_DL_LOSSES
Float
Downlink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
CONFIG_UL_LOSSES
Float
Uplink losses due to the configuration of the BTS (duplexer and/or combiner)
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Base Station Equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Base Station
Null column allowed: Yes Default value: 0
RHO_FACTOR
Short
Rho factor (not used)
Null column allowed: Yes Default value: 100
8.4 CoordSys Table For the projection coordinate system and the database’s internal coordinate system ( this is the display coordinate system used when creating a database).
220
Field
Type
Description
Attributes
CODE
Integer
Identification number of the coordinate system (the code of userdefined coordinate systems is an integer higher than 32768)
Null column allowed: No Default value: 0
DATUM_CODE
Double
DATUM_ROTX
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTY
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTZ
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_SCALE
Double
Parts per million (ppm)
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
DATUM_SHIFTX
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTY
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTZ
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_CODE
Integer
ELLIPS_RMAJOR
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_RMINOR
Double
Meters
Null column allowed: Yes Default value: 0
NAME
Text (50)
Coordinate system name
Null column allowed: No Default value:
PROJ_ANGLE
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_FALSE_EASTING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FALSE_NORTHING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FIRST_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LATITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LONGITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_METHOD
Short
UTM, Undefined, NoProjection, Lambert1SP, Lambert2SP, Mercator, CassiniSoldner, TransMercator, TransMercatorSO, ObliqueStereographic, NewZealandMapGrid, HotineOM, LabordeOM, SwissObliqueCylindical
Null column allowed: Yes Default value: 0
PROJ_SCALE_FACTOR
Double
PROJ_SECOND_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_ZONE_NUMBER
Integer
Used with UTM
Null column allowed: Yes Default value: 0
Null column allowed: No Default value: 0
Null column allowed: Yes Default value: 0
8.5 CustomFields Table For defining user-defined fields added to tables, default values for any field (including user-defined fields), and choice lists, captions, and group names for user-defined fields. Field
Type
Description
Attributes
CAPTION
Text (50)
Caption of the field (displayed instead of the name)
Null column allowed: Yes Default value:
CHOICE_LIST
Memo
Choice list for the field
Null column allowed: Yes Default value:
CHOICE_TYPE
Integer
0=Choice list is optional; 1=Choice list is mandatory
Null column allowed: Yes Default value: 0
COLUMN_NAME
Text (50)
Second part of the unique key. Field name
Null column allowed: No Default value:
DEFAULT_VALUE
Text (50)
Default value for the field
Null column allowed: Yes Default value:
DISPLAY_TYPE
Integer
0: Field is modifiable; 1: Field is read-only
Null column allowed: Yes Default value: 0
221
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
GROUP_NAME
Text (50)
Name of the group to which that field belongs
Null column allowed: Yes Default value:
TABLE_NAME
Text (50)
First part of the unique key. Table name
Null column allowed: No Default value:
These are some general recommendations that you should follow when handling databases. General • • • •
In order to use Atoll with Oracle, you must create Oracle users and schema with names in uppercase. Create backups of the database before upgrading. It is recommended to define a rule for making backups of the database at regular intervals. Do not skip a major Atoll version. For example, if you are currently using Atoll 2.7.xV6.7, you should first upgrade the database to Atoll 2.8.xV6.9 before upgrading to Atoll 3.1.xV7.1. Upgrading your database will be simpler if you do not skip a major version. If you skip or have skipped an intermediate major version, you must upgrade your database twice in order to make it compatible with the new version.
Tables and Fields • •
Table and field names are case sensitive. Table and field names should be not more than 20 characters long. Oracle databases allow a maximum length of 30 characters for field and table names. However, for use in Atoll, you must not create tables and fields with names longer than 20 characters. This is because Atoll adds some characters to the table and field names for certain operations: creating associated triggers, creating project databases, etc. Limiting the length of table and field names to 20 characters will help avoid database connection and consistency problems.
• • • • • •
• •
Table and field names should only use alphanumeric characters (A-Z, a-z, 0-9) and underscores (_). Table and field names must not start with a numeric character (0-9). Table and field names must not contain an SQL or RDBMS-specific keyword, such as ORDER, DATE, etc. Table and field names must not contain spaces or special characters, such as periods (.), exclamation marks (!), colons (:), semi-colons (;), interrogation marks (?), parentheses (()), brackets ({}), square brackets ([]), etc. Boolean fields, system or user-defined, should always have default values assigned. The CustomFields table enables you to define default values, choice lists, and read/write access for any field in any table in Atoll, including user-defined fields that you add to the Atoll tables. The values defined in this table have priority over the internal predefined default values. If you define floating point default values, make sure that all the users have the same decimal separator. If you wish to add custom fields in the Atoll document, you should first add the field in the database, and then update your Atoll document from the database. When setting up your database for the first time, try to anticipate user requirements in terms of custom fields in Atoll tables. Some requirements of the different user groups can be satisfied if a few general-purpose user-defined fields are added in Atoll tables when setting up the database. For example, if you add three user-defined fields (one of type integer, float, and text (limited size)) to the Sites and Transmitters tables, users will be able to use these for sorting, filtering, grouping, or other purposes. This approach can help the database function a long time before users require the addition of other custom fields.
• •
•
To improve performance, if your projects allow it, reduce the size of the fields corresponding to the sites and transmitters’ names. To improve performance, unless absolutely necessary, do not add user-defined fields of Text type. Rather, use numeric field types, which allow sorting and other functions. If you must add Text fields, allocate them the appropriate size that would suffice. For example, a 255-character long Text type field would, for the most part, occupy disk space for no purpose. To improve performance, you should avoid adding custom fields to the neighbour management tables.
8.6 FeederEquipments Table For feeders. Field
Type
Description
Attributes
CONNECTOR_LOSSES_DL
Float
Feeder connector losses in downlink
Null column allowed: Yes Default value: 0
CONNECTOR_LOSSES_UL
Float
Feeder connector losses in uplink
Null column allowed: Yes Default value: 0
222
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
LOSS_PER_METER
Float
Feeder loss per meter
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Feeder
Null column allowed: No Default value:
8.7 FrameConfigurations Table For frame configurations. Field
Type
Description
Attributes
CYCLIC_PREFIX
Short
Cyclic prefix ratio (NULL; 0: 1/4; 1: 1/8; 2: 1/16; 4: 1/32)
Null column allowed: Yes Default value:
N_FFT
Short
Total number of subcarriers per channel bandwidth for this frame configuration
Null column allowed: Yes Default value: 256
NAME
Text (50)
Name of the frame configuration
Null column allowed: No Default value: "Default Frame"
PREAMBLE_N_USED
Short
The number of subcarriers used for the preamble
Null column allowed: No Default value:
SEGMENTATION
Boolean
If true, the first DL PUSC zone is segmented
Null column allowed: No Default value: False
UL_SEGMENTATION
Boolean
If true, the first UL PUSC zone is segmented
Null column allowed: No Default value: False
8.8 FrequencyBands Table For frequency bands. Field
Type
Description
Attributes
ADJ_CHANNEL_PROT
Float
Protection against interfering signals from adjacent channels
Null column allowed: No Default value: 11
CHANNEL_WIDTH
Double
Width of each physical channel composing the frequency band Unit: MHz
Null column allowed: Yes Default value: 1
DELTA_CN
Integer
Numeric difference between two adjacent channels
Null column allowed: Yes Default value: 1
DL_FREQUENCY
Double
DL frequency of the 1st channel Unit: MHz
Null column allowed: Yes Default value:
DUPLEXING_METHOD
Short
Duplexing method used in the frequency band Choice list: 0=FDD; 1=TDD;
Null column allowed: No Default value: 0
EXCLUDED_CHANNELS
Text (255)
Physical channels you do not want to allocate
Null column allowed: Yes Default value:
FIRST_CHANNEL
Integer
Number of the first physical channel of the frequency band
Null column allowed: Yes Default value: 0
GUARD_BAND
Float
Guard band between carriers (MHz)
Null column allowed: Yes Default value: 0
LAST_CHANNEL
Integer
Number of the last physical channel of the frequency band
Null column allowed: Yes Default value: 9
NAME
Text (50)
Name of the frequency band
Null column allowed: No Default value:
SAMPLING_FACTOR
Float
Ratio between the channel bandwidth and its sampling frequency
Null column allowed: No Default value: 1
UL_FREQUENCY
Double
UL frequency of the 1st channel Unit: MHz
Null column allowed: Yes Default value:
223
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
8.9 InterNetChProtect Table For inter-network interference reduction factor graphs. Field
Type
Description
Attributes
ICP
Memo
Inter-network channel protection = f( MHz)
Null column allowed: Yes Default value:
ITF_BW
Double
Interfering bandwidth (kHz)
Null column allowed: No Default value: 0
ITF_TECHNO
Text (50)
Interfering technology
Null column allowed: No Default value:
V_BW
Double
Victim bandwidth (kHz)
Null column allowed: No Default value: 0
8.10 MUGTables Table For multi-user diversity gains. Field
Type
Description
Attributes
MAX_CINR
Float
C/(I+N) above which no MUG will be applied.
Null column allowed: No Default value: 16.8
MOBILITY
Text (50)
Mobility type for which the MUG table is defined.
Null column allowed: No Default value:
MUG_TABLE
Memo
Multi-user diversity gain table
Null column allowed: Yes Default value:
SCHEDULER_NAME
Text (30)
Name of the scheduler for which the MUG table is defined.
Null column allowed: No Default value:
8.11 Neighbours Table For intra-technology neighbour relations. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Neighbour cell
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
RELATION_TYPE
Short
Type of the neighbour relation: 0=Intra-carrier; 1=Inter-carrier
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
8.12 NeighboursConstraints Table For intra-technology neighbour allocation constraints. Field
224
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Neighbour cell
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
STATUS
Integer
Constraint used in automatic allocation. 0 = Forced; 1 = Forbidden.
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
8.13 NeighboursConstraintsExt Table For inter-technology neighbour allocation constraints. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value:
NEIGHBOUR
Text (50)
Neighbour cell or transmitter
Null column allowed: No Default value:
STATUS
Integer
Constraint used in automatic allocation. 0 = Forced; 1 = Forbidden.
Null column allowed: Yes Default value: 0
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
8.14 NeighboursExt Table For inter-technology neighbour relations. Field
Type
Description
Attributes
IMPORTANCE
Float
Handover importance
Null column allowed: Yes Default value: 1
NEIGHBOUR
Text (50)
Neighbour cell
Null column allowed: No Default value:
REASON
Integer
Reason of the neighbourhood Choice list: 0=Manual; 1=Forced; 2=Co-site; 3=Adjacent; 4=Symmetric; 5=Distance; 6=Coverage;
Null column allowed: Yes Default value: 0 (Manual)
TRANSMITTER
Text (50)
Reference cell
Null column allowed: No Default value:
TYPE
Text (50)
Type of the neighbourhood (handover, measurement…)
Null column allowed: Yes Default value:
8.15 Networks Table For network-level parameters. Field
Type
Description
Attributes
AMS_SEL_CRITERION
Short
AMS criterion (0 - Preamble C/N; 1 - Preamble C/(I+N))
Null column allowed: Yes Default value: 0
BS_SELECTION
Short
Best server selection method: 0=Preamble signal level; 1=Preamble C/N;
Null column allowed: Yes Default value: 0
CELL_SELECTION
Short
Serving cell selection method (0 = Obsolete, 1 = Obsolete, 2 = Random, 3 = Distributive)
Null column allowed: Yes Default value: 2
CYCLIC_PREFIX
Short
Cyclic prefix ratio Choice list: 0=1/4; 1=1/8; 2=1/16; 4=1/32;
Null column allowed: No Default value: 1
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: "CostHata"
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: No Default value: 50
DEFAULT_RTG
Float
Receive Time Guard, RTG (TDD only) Unit: ms
Null column allowed: No Default value: 0
225
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DEFAULT_TTG
Float
Transmit Time Guard, TTG (TDD only) Unit: ms
Null column allowed: No Default value: 0
DL_RATIO_FORMAT
Short
Format of the DL ratio parameter (0: Percentage; 1: Fraction)
Null column allowed: Yes Default value: 0
DL_SYM_DURATIONS_NB
Short
Number of symbol durations in the downlink subframe (including the symbol duration used for the Preamble)
Null column allowed: Yes Default value: 32
DL_UL_RATIO
Float
DL subframe symbol number / UL subframe symbol number (TDD only) Unit: %
Null column allowed: No Default value: 66.667
DMAX
Float
Maximum radius for a cell
Null column allowed: No Default value: -1
FIX_DL_OVERHEAD
Short
DL overhead expressed in symbol durations
Null column allowed: No Default value: 1
FIX_UL_OVERHEAD
Integer
UL overhead expressed in symbol durations
Null column allowed: No Default value: 0
FRAME_DURATION
Short
The length of a frame Choice list: 0=20 ms; 1=12.5 ms; 2=10 ms; 3=8 ms; 4=5 ms; 5=4 ms; 6=2.5 ms; 7=2 ms;
Null column allowed: No Default value: 4
INTERFERERS_RX_THRESH
Float
Interferers' reception threshold
Null column allowed: Yes Default value: -20
MIMO_INT_PWR_COMB
Short
Whether interfering signals are combined over multiple antennas or not
Null column allowed: Yes Default value: 0
N_DATA
Short
Number of subcarriers per channel used for data transfer (N_USED - pilot subcarriers)
Null column allowed: Yes Default value: 192
N_FFT
Short
Total number of subcarriers per channel
Null column allowed: Yes Default value: 256
N_SUBCHANNELS_CH
Short
Number of subchannels per channel
Null column allowed: Yes Default value: 16
N_USED
Short
Number of used subcarriers per channel (N_FFT - guard subcarriers)
Null column allowed: Yes Default value: 200
NAME
Text (50)
Type of network
Null column allowed: No Default value:
POWER_CONTROL_MARGIN
Float
Margin Over Max Bearer Threshold defining C/I Target (dB)
Null column allowed: Yes Default value: 1
PZ_SEL_CRITERION
Short
Permutation zone selection criterion (0 - Preamble C/N; 1 - Preamble C/(I+N))
Null column allowed: Yes Default value: 0
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value: ‘IEEE 802.16e’
TECHNOLOGY
Text (10)
Name of the technlogy
Null column allowed: No Default value: ‘OFDM’
THERMAL_NOISE
Float
Thermal noise
Null column allowed: Yes Default value: -121
UL_SYM_DURATIONS_NB
Short
Number of symbol durations in the uplink subframe
Null column allowed: Yes Default value: 15
VARIABLE_DL_OVERHEAD
Float
DL overhead expressed in trame percentage
Null column allowed: No Default value: 0
VARIABLE_UL_OVERHEAD
Float
UL overhead expressed in trame percentage
Null column allowed: No Default value: 0
226
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
8.16 PermutationZones Table For permutation zones. Field
Type
Description
Attributes
AUTO_ACTIVATE
Boolean
If true, the permutation zone is activated for new cells
Null column allowed: No Default value: False
DIVERSITY_SUPPORT
Short
The type of antenna diversity supported by the permutation zone
Null column allowed: Yes Default value: 1
FRAME_CONFIG
Text (50)
Name of the frame configuration (from the FrameConfigurations table)
Null column allowed: No Default value:
MAX_DISTANCE
Float
Coverage limit for the zone in terms of maximum distance from the cell
Null column allowed: Yes Default value: 500000
MAX_SPEED
Float
Highest user speed that can use this permutation zone (km/h)
Null column allowed: Yes Default value: 150
N_DATA
Short
Number of subcarriers per channel used for data transfer (N_USED - pilot subcarriers)
Null column allowed: Yes Default value: 192
N_SUBCHANNELS_CH
Short
Number of subchannels per channel
Null column allowed: Yes Default value: 16
N_USED
Short
Number of used subcarriers per channel (N_FFT - guard subcarriers - DC subcarrier)
Null column allowed: Yes Default value: 200
PRIORITY
Short
Permutation zone priority (0: lowest)
Null column allowed: Yes Default value: 0
QUALITY_THRESHOLD
Float
Minimum signal quality required to use this zone (dB)
Null column allowed: Yes Default value: -5
SC_GROUPS_SEG0
Short
Subchannel groups used by segment 0
Null column allowed: Yes Default value: 3
SC_GROUPS_SEG1
Short
Subchannel groups used by segment 1
Null column allowed: Yes Default value: 12
SC_GROUPS_SEG2
Short
Subchannel groups used by segment 2
Null column allowed: Yes Default value: 48
SUBCHANNEL_ALLOC_MODE
Short
SUBFRAME
Short
Downlink Subframe or Uplink Subframe Choice list: 0=DL; 1=UL;
Null column allowed: No Default value: 0
ULSC_GROUPS_SEG0
Text (255)
Uplink subchannels belonging to segment 0 of the cell
Null column allowed: Yes Default value:
ULSC_GROUPS_SEG1
Text (255)
Uplink subchannels belonging to segment 1 of the cell
Null column allowed: Yes Default value:
ULSC_GROUPS_SEG2
Text (255)
Uplink subchannels belonging to segment 2 of the cell
Null column allowed: Yes Default value:
USED_SC_GROUPS
Short
ZONE_ID
Short
Name of the subchannel allocation mode Null column allowed: Yes Choice list: 0=PUSC DL; 1=FUSC; 2=OFUSC; 3=AMC; 4=TUSC 1; 5=TUSC 2; Default value: 0 6=PUSC UL; 7=OPUSC;
The secondary subchannel groups used by the segmented DL PUSC zone Null column allowed: Yes (Obsolete) Default value: Zone identifier Choice list: 0 to 7 for DL; 0 to 2 for UL;
Null column allowed: No Default value: 0
8.17 PropagationModels Table For propagation models. Field
Type
Description
Attributes
Data
Binary
Model specific parameters
Null column allowed: Yes Default value:
Description
Text (255)
User defined
Null column allowed: Yes Default value:
227
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
Name
Text (50)
Name of the propagation model
Null column allowed: No Default value:
Signature
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
Type
Text (50)
ProgID of the model
Null column allowed: No Default value:
8.18 QualityIndicators Table For quality indicators (BER, BLER, etc.). Field
Type
Description
Attributes
CS_QI
Boolean
Flag indicating whether the Quality Indicator is used for Voice (CS) services
Null column allowed: No Default value: True
MEAS_PARAM
Short
Name of the measured figure used for this QI determination Choice list: 0=C; 1=CIR;
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
PS_QI
Boolean
Flag indicating whether the Quality Indicator is used for Data (PS) services
Null column allowed: No Default value: True
USE_INTERPOLATION
Boolean
Flag indicating whether the Quality Indicator must be interpolated or not
Null column allowed: No Default value: True
8.19 Receivers Table For receiver parameters. Field
Type
Description
Attributes
ANTENNA
Text (50)
Receiver's antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the receiver Unit: m
Null column allowed: No Default value: 1.5
LOSS
Float
Losses due to receiver radio equipment (up and downlink) Unit: dB
Null column allowed: No Default value: 0.
NAME
Text (50)
Name of the receiver
Null column allowed: No Default value:
8.20 RepeaterEquipments Table For repeater equipment. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
MANUFACTURER
Text (50)
Manufacturer of the repeater equipment
Null column allowed: Yes Default value:
MAX_AMPLIFIER_GAIN
Float
Maximum gain of the amplifier (dB)
Null column allowed: Yes Default value: 90
MAX_OUTPUT_DL
Float
Maximum downlink output power (dBm)
Null column allowed: Yes Default value: 30
MAX_OUTPUT_UL
Float
Maximum uplink output power (dBm)
Null column allowed: Yes Default value: 12
MIN_AMPLIFIER_GAIN
Float
Minimum gain of the amplifier (dB)
Null column allowed: Yes Default value: 50
228
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
NAME
Text (50)
Name of the repeater equipment
Null column allowed: No Default value:
NOISE_FIGURE
Float
Repeater noise Figure (dB)
Null column allowed: Yes Default value: 5
STEP_AMPLIFIER_GAIN
Float
Step of amplifier gain (dB)
Null column allowed: Yes Default value: 1
TIME_DELAY
Float
Time delay in the equipment (microseconds)
Null column allowed: Yes Default value: 5
8.21 Repeaters Table For repeaters. Field
Type
Description
Attributes
AMPLIFIER_GAIN
Float
Gain of the amplifier
Null column allowed: Yes Default value: 80
AZIMUT
Float
Azimuth of the donor side antenna
Null column allowed: Yes Default value: 0
DONOR_CELLID
Text (50)
Name of the donor cell
Null column allowed: No Default value:
DONOR_LINK_LOSS
Float
Loss (dB) between donor and donor side of the repeater
Null column allowed: Yes Default value: 0
DONOR_LINK_TYPE
Short
1- Off air 2- Microwave 3- Fibre
Null column allowed: No Default value: 1
DONOR_PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction between donor and repeater
Null column allowed: Yes Default value:
DOWNTILT
Float
Downtilt of the donor side antenna
Null column allowed: Yes Default value: 0
EQUIPMENT_NAME
Text (50)
If no equipment, the repeater is a passive component
Null column allowed: Yes Default value:
FEEDER_NAME
Text (50)
Name of the donor side feeder
Null column allowed: Yes Default value:
FEEDERLENGTH
Float
Length of donor side feeder
Null column allowed: Yes Default value: 0
HEIGHT
Float
Height of the donor side antenna
Null column allowed: Yes Default value: 25
REC_ANTENNA
Text (50)
Name of the donor side antenna
Null column allowed: Yes Default value:
REC_FEEDERLENGTH_UL
Float
Length of donor side uplink feeder
Null column allowed: Yes Default value: 0
TOTAL_GAIN
Float
Total gain to be applied to donor cell pilot power
Null column allowed: Yes Default value: 0
TOTAL_GAIN_UL
Float
Uplink total gain to be applied to mobile output power
Null column allowed: Yes Default value: 0
TX_ID
Text (50)
Name of the repeater (and of the transmitter used for coverage)
Null column allowed: No Default value:
Repeater properties are saved in two tables: the donor-side parameters are in the Repeaters table and the coverage-side parameters in the Transmitters table.
8.22 Schedulers Table For schedulers.
229
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
BEARER_SELECTION
Short
NAME
Text (30)
Name of the scheduler
Null column allowed: No Default value:
QOS_BIAS_FACTOR
Float
Weight ratio for better QoS (%)
Null column allowed: No Default value: 0
SCHEDULING_METHOD
Short
TARGET_THROUGHPUT_DAT A
Short
0 = Peak MAC Throughput; 1 = Effective MAC Throughput; 2 = Application Throughput
Null column allowed: Yes Default value: 0
TARGET_THROUGHPUT_VOI CE
Short
0 = Peak MAC Throughput; 1 = Effective MAC Throughput; 2 = Application Throughput
Null column allowed: Yes Default value: 0
UL_BW_ALLOCATION
Short
UL Bandwidth Allocation Target: 0 – Full Bandwidth; 1 – Maintain Connection; 2 – Best Bearer
Null column allowed: Yes Default value: 2
Bearer Selection Criterion: 0 – Bearer Index; 1 – Peak MAC Throughput; Null column allowed: Yes 2 – Effective MAC Throughput Default value: 0
0 = Proportional Fair; 1 = Proportional Demand; 2 = Biased (QoS Class); 3 Null column allowed: Yes = Max Aggregate Throughput Default value: 0
8.23 SecondaryAntennas Table For additional antennas. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna installed on the transmitter (from the Antennas table)
Null column allowed: No Default value:
AZIMUT
Float
Azimuth of the antenna
Null column allowed: No Default value: 0
PERCENT_POWER
Float
Percentage of power dedicated to the secondary antenna
Null column allowed: No Default value: 0
REDT
Float
Remote Electrical tilt of the secondary antenna
Null column allowed: Yes Default value: 0
TILT
Float
Mechanical downtilt of the secondary antenna
Null column allowed: No Default value: 0
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
8.24 Sites Table For sites.
230
Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude (user-defined) Unit: m
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Additional information about the site
Null column allowed: Yes Default value:
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
MAX_BH_RATE_DL
Float
Backhaul maximum DL throughput (kbps)
Null column allowed: Yes Default value: 950000
MAX_BH_RATE_UL
Float
Backhaul maximum UL throughput (kbps)
Null column allowed: Yes Default value: 950000
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value: 0
8.25 SitesLists Table For sites belonging to site lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list
Null column allowed: No Default value:
SITE_NAME
Text (50)
Second part of the unique key. Name of the site
Null column allowed: No Default value:
8.26 SitesListsNames Table For names of site lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
8.27 SmartAntennas Table For smart antenna equipment. Field
Type
Description
Attributes
BROADCAST_ANTENNA
Text (50)
Broadcast (main) antenna model for the smart antenna
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the Smart Antenna
Null column allowed: No Default value:
SA_MODEL
Text (50)
Smart antenna model used
Null column allowed: Yes Default value:
8.28 SmartAntennasModels Table For smart antenna models. Field
Type
Description
Attributes
SA_DATA
Binary
Smart antenna model data
Null column allowed: Yes Default value:
SA_DESCRIPTION
Text (50)
Description of the smart antenna model
Null column allowed: Yes Default value:
SA_NAME
Text (50)
Name of the smart antenna model
Null column allowed: No Default value:
SA_SIGNATURE
Text (50)
Signature of the smart antenna model
Null column allowed: No Default value:
SA_TYPE
Text (50)
Type of the smart antenna model
Null column allowed: No Default value:
8.29 TMAEquipments Table For tower-mounted amplifiers.
231
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
DL_LOSSES
Float
Downlink losses of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of Tower Mounted Amplifier
Null column allowed: No Default value:
NOISE_FIGURE
Float
Noise figure of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
UL_GAIN
Float
Uplink gain of Tower Mounted Amplifier
Null column allowed: Yes Default value: 0
8.30 TplTransmitters Table For station templates. Field
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value:
AMS_THRESHOLD
Float
CINR threshold in dB to switch from SM to STTD/MRC
Null column allowed: Yes Default value:
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter (from the Antennas table)
Null column allowed: No Default value:
AZIMUT
Float
Azimuth of the main antenna
Null column allowed: Yes Default value:
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
CALC_RADIUS2
Integer
Second calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value:
CALC_RESOLUTION2
Integer
Second calculation resolution
Null column allowed: Yes Default value:
CELL_SIZE
Float
Radius of the cell (schematically represented by an hexagon) Unit: m
Null column allowed: Yes Default value:
CHANNEL_LIST
Text(255)
Channel numbers used by transmitters
Null column allowed: Yes Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DL_LOAD
Float
Downlink traffic load
Null column allowed: Yes Default value:
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value:
FBAND
Text (50)
Frequency band of the cell
Null column allowed: No Default value:
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value:
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value:
FRAME_CONFIG
Text (50)
HEIGHT
Float
232
Calculation radius used to define each transmitter calculation area Unit: Null column allowed: Yes m Default value:
Defines the subchannel, subcarrier, and permutation zone configuration Null column allowed: Yes used at the cell Default value: Antenna height above the ground Unit: m
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
IDLE_PILOT_POWER_OFFSET
Float
Pilot power offset = Preamble power - Idle Pilot power (dB)
Null column allowed: Yes Default value:
LAYER_LIST
Text (255)
List of layers
Null column allowed: Yes Default value: 0
MAX_DL_LOAD
Float
Maximum traffic load allowed on downlink
Null column allowed: Yes Default value:
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum number of inter-technology neighbours
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Integer
Maximum number of intra-technology neighbours
Null column allowed: Yes Default value:
MAX_NUMBER_OF_USERS
Integer
Max supported number of users for the cell
Null column allowed: Yes Default value:
MAX_UL_LOAD
Float
Maximum traffic load allowed on uplink
Null column allowed: Yes Default value:
MIMO_RX_ANTENNAS
Short
Number of reception antennas used for MIMO
Null column allowed: Yes Default value:
MIMO_TX_ANTENNAS
Short
Number of transmission antennas used for MIMO
Null column allowed: Yes Default value:
MISCDLL
Float
Miscellaneous downlink loss
Null column allowed: Yes Default value:
MISCULL
Float
Miscellaneous uplink loss
Null column allowed: Yes Default value:
NAME
Text (50)
Template name
Null column allowed: No Default value:
NOISE_FIGURE
Float
Total Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value:
NOISE_RISE_UL
Float
Uplink interference noise rise (dB)
Null column allowed: Yes Default value:
NOISE_RISE_UL_SEG
Float
Uplink noise rise for the segmented permutation zone
Null column allowed: Yes Default value:
NUM_SECTORS
Integer
Number of sectors
Null column allowed: No Default value:
PI_DOMAIN_NAME
Text (50)
Name of the preamble index domain
Null column allowed: Yes Default value:
PI_LIST
Text(255)
Preamble indexes used by transmitters
Null column allowed: Yes Default value:
PI_REUSE_MIN_DIST
Float
The minimum reuse distance for the AFP and preamble index allocation
Null column allowed: Yes Default value:
PILOT_POWER_OFFSET
Float
Pilot power offset = Preamble power - Pilot power (dB)
Null column allowed: Yes Default value:
POWER
Float
Cell output power (dBm)
Null column allowed: Yes Default value:
PREAMBLE_QUALITY_THRES
Float
Required CNR quality for the preamble signal
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (255)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (255)
Name of the second propagation model used to calculate prediction
Null column allowed: Yes Default value:
REDT
Float
Remote Electrical tilt
Null column allowed: Yes Default value:
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
SA_NAME
Text (50)
Name of the associated smart antenna
Null column allowed: Yes Default value:
233
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
SCHEDULER
Text (30)
Scheduler used by the cell
Null column allowed: Yes Default value:
SEGMENTATION_USAGE
Float
Segmentation usage ratio
Null column allowed: Yes Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
TILT
Float
Mechanical downtilt of the main antenna
Null column allowed: Yes Default value:
TMA_NAME
Text (50)
Name of theTower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TRAFFIC_POWER_OFFSET
Float
Traffic power offset = Preamble power - traffic power (dB)
Null column allowed: Yes Default value:
TX_TYPE
Short
Type of transmitter (0 = Normal; 1 = Interferer only)
Null column allowed: Yes Default value:
TXLOSSES
Float
Losses on the downlink due to transmitter radio equipment Unit: dB
Null column allowed: Yes Default value:
UL_LOAD
Float
Uplink traffic load
Null column allowed: Yes Default value:
UL_MU_SM_GAIN
Float
Multi-user (collaborative) MIMO gain in uplink
Null column allowed: Yes Default value:
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value:
WEQUIPMENT
Text (50)
Cell equipment
Null column allowed: Yes Default value:
8.31 Transmitters Table For transmitters. Field
234
Type
Description
Attributes
ACTIVE
Boolean
Transmitter activity: 'Yes' means that the transmitter is active
Null column allowed: No Default value: True
ANTENNA_NAME
Text (50)
Name of the main antenna installed on the transmitter (from the Antennas table)
Null column allowed: Yes Default value:
AZIMUT
Float
Azimuth of the first antenna
Null column allowed: Yes Default value: 0
BTS_NAME
Text (50)
Name of the BTS equipment
Null column allowed: Yes Default value:
CALC_RADIUS
Integer
Calculation radius used to define the calculation area Unit: m
Null column allowed: Yes Default value: 4000
CALC_RADIUS2
Integer
Second calculation radius Unit: m
Null column allowed: Yes Default value:
CALC_RESOLUTION
Integer
Calculation resolution
Null column allowed: Yes Default value: 50
CALC_RESOLUTION2
Integer
Second calculation resolution
Null column allowed: Yes Default value:
CELL_SIZE
Float
Radius of the cell (schematically represented by an hexagon)
Null column allowed: Yes Default value: 2000
COMMENT_
Text (255)
Additional information about the transmitter
Null column allowed: Yes Default value:
DX
Float
X coordinate relative to the site position
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
DY
Float
Y coordinate relative to the site position
Null column allowed: Yes Default value: 0
FEEDER_NAME
Text (50)
Name of the feeder equipment
Null column allowed: Yes Default value:
FEEDERLENGTH_DL
Float
Length of downlink feeder Unit: m
Null column allowed: Yes Default value: 0
FEEDERLENGTH_UL
Float
Length of uplink feeder Unit: m
Null column allowed: Yes Default value: 0
HEIGHT
Float
Antenna height above the ground Unit: m
Null column allowed: Yes Default value: 25
HEXAGON_GROUP
Text (50)
Group of hexagons which contains this transmitter
Null column allowed: Yes Default value:
MIMO_RX_ANTENNAS
Short
Number of MIMO antennas used for reception
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of MIMO antennas used for transmission
Null column allowed: Yes Default value: 1
MISCDLL
Float
Miscellaneous downlink loss
Null column allowed: Yes Default value: 0
MISCULL
Float
Miscellaneous uplink loss
Null column allowed: Yes Default value: 0
NOISE_FIGURE
Float
Total Noise figure used to determine the thermal noise at the transmitter
Null column allowed: Yes Default value: 5
POLARIZATION
Text (1)
Polarization of the antennas installed at the transmitter
Null column allowed: Yes Default value: "V"
PROPAG_MODEL
Text (50)
Name of the propagation model used to calculate prediction
Null column allowed: Yes Default value:
PROPAG_MODEL2
Text (50)
Name of the second propagation model used to calculate prediction
Null column allowed: Yes Default value:
REDT
Float
Remote electrical tilt of the main antenna
Null column allowed: Yes Default value: 0
RXLOSSES
Float
Losses on the uplink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
SA_NAME
Text (50)
Name of the smart antenna assigned to the transmitter
Null column allowed: Yes Default value:
SHAREDMAST
Text (50)
Shared mast name: enables antenna sharing between transmitters
Null column allowed: Yes Default value:
SIDE_TILT
Float
Mechanical side-tilt of the main antenna
Null column allowed: Yes Default value: 0
SITE_NAME
Text (50)
Name of the site at which the transmitter is located (from the Sites table)
Null column allowed: No Default value:
TILT
Float
Mechanical downtilt of the first antenna
Null column allowed: Yes Default value: 0
TMA_NAME
Text (50)
Name of theTower Mounted Amplifier equipment
Null column allowed: Yes Default value:
TX_ID
Text (50)
Transmitter name
Null column allowed: No Default value:
TX_TYPE
Short
Type of transmitter (0 = Normal; 1 = Interferer only)
Null column allowed: Yes Default value: 0
TXLOSSES
Float
Losses on the downlink due to transmitter radio equipment
Null column allowed: Yes Default value: 0
8.32 TxsLists Table For transmitters belonging to transmitter lists.
235
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list.
Null column allowed: No Default value:
TX_NAME
Text (50)
Second part of the unique key. Name of the transmitter.
Null column allowed: No Default value:
8.33 TxsListsNames Table For names of transmitter lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the transmitter list
Null column allowed: No Default value:
8.34 Units Table For the reception and transmission units, the projection coordinate system specified in the ATL document, and the database internal coordinate system. Field
Type
Description
Attributes
COORD_SYSTEM
Integer
Display coordinate system when creating database
Null column allowed: Yes Default value: -1
GAIN_UNIT
Integer
Unit used for gains (dBd or dBi) Choice list: 0=dBd; 1=dBi;
Null column allowed: Yes Default value: 0
PROJECTION
Integer
Projected coordinate system for geo data
Null column allowed: Yes Default value: -1
RECEPTION_UNIT
Integer
Reception unit when creating database Choice list: 0=dBm; 1=dbµV; 2=dbµV/m;
Null column allowed: No Default value: 0
TRANSMISSION_UNIT
Integer
Transmission unit when creating database Choice list: 0=dBm; 1=Watts; 2=kWatts;
Null column allowed: No Default value: 0
8.35 WBearerQualityCurves Table For bearer performance graphs. Field
Type
Description
Attributes
BEARER_INDEX
Short
Bearer index
Null column allowed: No Default value: 0
MOBILITY
Text (50)
Mobility type
Null column allowed: Yes Default value:
QI_CURVE
Memo
DL Quality QI=f(MEAS_PARAM) MEAS_PARAM from QualityIndicators table
Null column allowed: Yes Default value:
QI_NAME
Text (50)
Name of the Quality Indicator
Null column allowed: No Default value:
RX_EQUIP
Text (50)
Name of the reception equipment
Null column allowed: No Default value:
8.36 WBearers Table For bearers.
236
Field
Type
Description
Attributes
BEARER_INDEX
Short
Modulation and coding scheme number
Null column allowed: No Default value: 1
CODING_RATE
Float
Coding rate
Null column allowed: Yes Default value: 1
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
MODULATION
Short
Modulation type Choice list: 0=BPSK; 1=QPSK; 2=16QAM; 3=64QAM;
Null column allowed: No Default value: 1
NAME
Text (50)
Name of the radio bearer
Null column allowed: No Default value:
SPECTRAL_EFFICIENCY
Float
Spectral efficiency = Peak MAC Throughput per Hz Unit: bps/Hz
Null column allowed: Yes Default value: 0
8.37 WBearersRequiredCI Table For bearer selection thresholds. Field
Type
Description
Attributes
BEARERS_REQUIRED_COVERI
Memo
C/I required in DL for selecting a radio bearer C/I_Req = f(Best(BEARER_INDEX))
Null column allowed: Yes Default value:
MOBILITY
Text (50)
CPE mobility
Null column allowed: Yes Default value:
RX_EQUIP
Text (50)
Name of the reception equipment
Null column allowed: No Default value:
8.38 WCCHDivGains Table For control channel diversity gains. Field
Type
Description
Attributes
EQUIPMENT
Text (50)
Name of the reception equipment to which the control channel diversity gains correspond
Null column allowed: No Default value:
MIMO_RX_ANTENNAS
Short
Number of reception antennas used for MIMO
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of transmission antennas used for MIMO
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
Name of the mobility type to which the control channel diversity gains correspond
Null column allowed: Yes Default value:
PREAMBLE_DIV_GAIN
Float
Preamble diversity gain
Null column allowed: Yes Default value: 0
8.39 WCells Table For cells. Field
Type
Description
Attributes
AAS_RESULTS
Binary
Uplink and downlink AAS results from simulations
Null column allowed: Yes Default value:
AAS_USAGE
Float
Percentation of downlink traffic load supported by the smart antenna equipment
Null column allowed: Yes Default value: 50
ACTIVE
Boolean
Cell's activity. Cell is active if true.
Null column allowed: No Default value: True
AMS_THRESHOLD
Float
C/(I+N) threshold for switching from SM to STTD/MRC
Null column allowed: Yes Default value:
BSID
Text (50)
Cell connexion identifier
Null column allowed: Yes Default value:
CELL_ID
Text (50)
Name of the cell
Null column allowed: No Default value:
CELL_PERMBASE
Short
Cell PermBase
Null column allowed: Yes Default value: 0
237
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
CHANNEL
Integer
Channel number
Null column allowed: Yes Default value: 0
CHANNEL_STATUS
Short
Channel allocation status (0 = Not allocated, 1 = Allocated, 2 = Locked)
Null column allowed: Yes Default value: 0
COMMENT_
Text (255)
Additional information about the cell
Null column allowed: Yes Default value:
DL_LOAD
Float
Downlink cell traffic load
Null column allowed: Yes Default value: 1
DL_ZONE_PB
Integer
Downlink zone permbase
Null column allowed: Yes Default value:
DL_ZONE_PB_STATUS
Short
Downlink zone permbase allocation status: 0=Not allocated; 1=Allocated;2=Locked;
Null column allowed: Yes Default value: 0
DOWNLINK_EXTERNAL_NOIS E_RISE
Float
Inter-network downlink noise rise
Null column allowed: Yes Default value: 0
FBAND
Text (50)
Frequency band of the cell
Null column allowed: No Default value:
FRAME_CONFIG
Text (50)
IDLE_PILOT_POWER_OFFSET
Float
Offset (in dB) with respect to the preamble power for determining the pilot power during the empty part of the frame
Null column allowed: Yes Default value: 10
LOCKED_SEGMENT
Short
Segment locked for automatic allocation or not: 0=Unlocked; 1=Locked;
Null column allowed: Yes Default value: 0
MAX_DL_LOAD
Float
Maximum traffic load allowed on downlink
Null column allowed: Yes Default value: 100
MAX_EXT_NEIGHB_NUMBER
Integer
Maximum number of inter-technology neighbours for this cell
Null column allowed: Yes Default value:
MAX_NEIGHB_NUMBER
Integer
Maximum number of intra-technology neighbours for this cell
Null column allowed: Yes Default value:
MAX_NUMBER_OF_USERS
Integer
Max supported number of users for the cell
Null column allowed: Yes Default value:
MAX_UL_LOAD
Float
Maximum traffic load allowed on uplink
Null column allowed: Yes Default value: 100
NOISE_RISE_UL
Float
Uplink noise rise (dB). Manually specified by the user or calculated during simulations.
Null column allowed: Yes Default value: 0
NOISE_RISE_UL_SEG
Float
Uplink noise rise for the segmented permutation zone
Null column allowed: Yes Default value: 0
NUM_DL_USERS
Float
Number of DL connected users for the cell
Null column allowed: Yes Default value: 1
NUM_UL_USERS
Float
Number of UL connected users for the cell
Null column allowed: Yes Default value: 1
PI_DOMAIN_NAME
Text (50)
Name of the preamble index domain
Null column allowed: Yes Default value:
PI_REUSE_MIN_DIST
Float
The minimum reuse distance for the AFP and preamble index allocation
Null column allowed: Yes Default value:
PI_STATUS
Short
Preamble index status (0 = Not allocated, 1 = Allocated, 2 = Locked)
Null column allowed: Yes Default value: 0
PILOT_POWER_OFFSET
Float
Offset (in dB) with respect to the preamble power for determining the pilot power during the loaded part of the frame
Null column allowed: Yes Default value: 0
POWER
Float
Output PowerUnit: dBm
Null column allowed: Yes Default value: 43
PREAMBLE_INDEX
Integer
Preamble index of the cell
Null column allowed: Yes Default value: 0
PREAMBLE_QUALITY_THRES
Float
Required CNR quality for the preamble signal
Null column allowed: Yes Default value: -4
238
Defines the subchannel, subcarrier, and permutation zone configuration Null column allowed: Yes used at the cell Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
RANK
Short
Zero based order used by scheduler for sequential cell selection
Null column allowed: Yes Default value:
SCHEDULER
Text (30)
Scheduler used by the cell
Null column allowed: Yes Default value:
SEGMENT
Short
Cell segment
Null column allowed: Yes Default value: 0
SEGMENTATION_USAGE
Float
Percentation of downlink traffic load dedicated to the segmented zone
Null column allowed: Yes Default value: 50
TRAFFIC_POWER_OFFSET
Float
Offset (in dB) with respect to the preamble power for determining the traffic power
Null column allowed: Yes Default value: 3
TX_ID
Text (50)
Name of the transmitter to which the cell belongs
Null column allowed: No Default value:
UL_LOAD
Float
Uplink cell traffic load
Null column allowed: Yes Default value: 1
UL_MU_SM_GAIN
Float
Multi-user (collaborative) MIMO gain in uplink
Null column allowed: Yes Default value: 2
UL_ZONE_PB
Integer
Uplink zone permbase
Null column allowed: Yes Default value:
UL_ZONE_PB_STATUS
Short
Uplink zone permbase allocation status: 0=Not allocated; 1=Allocated;2=Locked
Null column allowed: Yes Default value: 0
UPLINK_EXTERNAL_NOISE_R ISE
Float
Inter-network uplink noise rise
Null column allowed: Yes Default value: 0
WEQUIPMENT
Text (50)
Reception equipment installed at the cell
Null column allowed: Yes Default value:
8.40 WEnvironmentDefs Table For traffic environment types. Field
Type
Description
Attributes
DENSITY
Float
Number of subscribers per km2
Null column allowed: Yes Default value: 0
ENVIRONMENT
Text (50)
Environment name
Null column allowed: No Default value:
MOBILITY
Text (50)
Type of mobility
Null column allowed: No Default value:
USER_PROFILE
Text (50)
Type of user profile
Null column allowed: No Default value:
8.41 WEquipments Table For reception equipment. Field
Type
Description
Attributes
NAME
Text (50)
Name of the reception equipment
Null column allowed: No Default value:
8.42 WLayers Table For network layers. Field LAYER_INDEX
Type Short
Description
Attributes
Index of the network layer
Null column allowed: No Default value: 0
239
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MAX_SPEED
Float
Maximum speed of mobiles for this layer
Null column allowed: Yes Default value: 300
NAME
Text (50)
Name of the network layer
Null column allowed: No Default value:
PRIORITY
Short
Priority of the network layer
Null column allowed: No Default value: 0
SELECTION_MARGIN
Float
Margin with respect to the highest signal level within which the layer is Null column allowed: Yes candidate for selection as server Default value: 0
8.43 WMimoConfigs Table For MIMO gain graphs. Field
Type
Description
Attributes
BEARER_INDEX
Short
Index of the radio bearer
Null column allowed: Yes Default value: 1
MAX_BLER
Float
Maximum value of BLER for which the gains are applicable
Null column allowed: Yes Default value: 1
MAX_MIMO_GAIN
Memo
Graph of maximum MIMO gains vs. C/(I+N)
Null column allowed: Yes Default value:
MIMO_RX_ANTENNAS
Short
Number of MIMO antennas used for reception
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of MIMO antennas used for transmission
Null column allowed: Yes Default value: 1
MOBILITY
Text (50)
User mobility
Null column allowed: Yes Default value:
MUMIMO_DIV_GAIN
Float
Diversity gain applicable with MU-MIMO
Null column allowed: Yes Default value: 0
STTD_GAIN
Float
Gain that will be applied to the CINR in STTD mode (dB)
Null column allowed: Yes Default value: 0
SUBCHANNEL_ALLOC_MODE
Short
Subchannel allocation mode
Null column allowed: Yes Default value: 8
SUMIMO_DIV_GAIN
Float
Diversity gain applicable with SU-MIMO
Null column allowed: Yes Default value: 0
WEQUIPMENT
Text (50)
Name of the equipment to which the MIMO gains correspond
Null column allowed: No Default value:
8.44 WMobility Table For mobility types. Field
Type
Description
Attributes
MEAN_SPEED
Float
Mean mobile speed (km/h) used for HSDPA
Null column allowed: Yes Default value: 0
NAME
Text (50)
Type of mobility
Null column allowed: No Default value:
8.45 WPIDomains Table For preamble index domains.
240
Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Name of the preamble index domain
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
8.46 WPIGroups Table For preamble index groups. Field
Type
Description
Attributes
DOMAIN_NAME
Text (50)
Name of the preamble index domain
Null column allowed: Default value:
EXCLUDED
Text (225)
EXTRA
Text (225)
Indexes to be added. It is forbidden for EXTRA and EXLUDED to have common numbers. Separator must be a blank character.
Null column allowed: Yes Default value:
FIRST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
LAST
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the preamble index group in the domain
Null column allowed: No Default value:
STEP
Integer
Group elements are: FIRST, FIRST+STEP, FIRST+2*STEP, …, FIRST+n*STEP. n is the greatest positive integer so that FIRST+n*STEP LAST.
Null column allowed: Yes Default value: 1
List of indexes to be excluded from the series defined by FIRST, LAST and Null column allowed: Yes STEP (separated by blank characters) Default value:
8.47 WServices Table For services. Field
Type
Description
Attributes
BODY_LOSS
Float
Losses due to the users body (dB)
Null column allowed: No Default value: 0
DL_ACTIVITY
Float
Activity factor for voice services on the downlink
Null column allowed: Yes Default value: 1
DL_DP
Float
Packet inter-arrival time (ms) in downlink
Null column allowed: Yes Default value: 0
DL_DPC
Float
Reading time (distance) between two packet calls (ms) in downlink
Null column allowed: Yes Default value: 0
DL_HIGHEST_BEARER
Float
The highest bearer to allowed to be used for this service in DL
Null column allowed: Yes Default value: 8
DL_LOWEST_BEARER
Short
The lowest bearer allowed to be used for this service in DL
Null column allowed: Yes Default value: 1
DL_MAXIMUM_LATENCY
Float
Maximum latency in DL (ms)
Null column allowed: Yes Default value: 0
DL_MRTR
Float
Minimum required transmission rate in DL (Committed Information Rate)
Null column allowed: No Default value: 0
DL_MSTR
Float
Maximum sustained trasmission rate in DL (Maximum Information Rate)
Null column allowed: No Default value: 0
DL_NPC
Integer
Number of packet calls during a session in downlink
Null column allowed: Yes Default value: 1
DL_SP
Integer
Packet size (Bytes) in downlink
Null column allowed: Yes Default value: 1500
DL_SPC_MAX
Float
Downlink maximum packet call size (kBytes)
Null column allowed: Yes Default value: 2000
DL_SPC_MIN
Float
Downlink minimum packet call size (kBytes)
Null column allowed: Yes Default value: 4
MAXIMUM_BLOCKING_PRO BA
Integer
Maximum probability of blocking (or delay) (%)
Null column allowed: Yes Default value: 0
241
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MIN_SC_UL
Integer
Minimum number of required subchannels for the service
Null column allowed: Yes Default value: 1
NAME
Text (50)
Service name
Null column allowed: No Default value:
PRIORITY
Short
Service priority (0: lowest)
Null column allowed: Yes Default value: 0
QOS_CLASS
Short
Quality of Service class (In order of priority defined by the IEEE 802.16 standard) Choice list: 0=UGS; 1=rtPS; 2=ErtPS; 3=nrtPS; 4=Best Effort;
Null column allowed: Yes Default value: 0
REQ_AVERAGE_DL_RATE
Float
Requested Average Downlink Rate (kbps)
Null column allowed: Yes Default value:
REQ_AVERAGE_UL_RATE
Float
Requested Average Uplink Rate (kbps)
Null column allowed: Yes Default value:
SUPPORTED_LAYER_LIST
Text (50)
List of network layers on which the service is allowed
Null column allowed: No Default value: “-1”
TH_OFFSET
Float
Offset to add to TH_SCALE_FACTOR
Null column allowed: No Default value: 0
TH_SCALE_FACTOR
Float
Ratio between application level throughput and MAC layer throughput
Null column allowed: No Default value: 95
TYPE
Short
Service type Choice list: 0=Voice; 1=Data;
Null column allowed: Yes Default value: 0
UL_ACTIVITY
Float
Activity factor for voice services on the uplink
Null column allowed: Yes Default value: 1
UL_DP
Float
Packet inter-arrival time (ms) in uplink
Null column allowed: Yes Default value: 0
UL_DPC
Float
Reading time (distance) between two packet calls (ms) in uplink
Null column allowed: Yes Default value: 0
UL_HIGHEST_BEARER
Float
The highest bearer to allowed to be used for this service in UL
Null column allowed: Yes Default value: 4
UL_LOWEST_BEARER
Short
The lowest bearer allowed to be used for this service in UL
Null column allowed: Yes Default value: 1
UL_MAXIMUM_LATENCY
Float
Maximum latency in UL (ms)
Null column allowed: Yes Default value: 0
UL_MRTR
Float
Minimum required transmission rate in UL (Committed Information Rate)
Null column allowed: No Default value: 0
UL_MSTR
Float
Maximum sustained trasmission rate in UL (Maximum Information Rate)
Null column allowed: No Default value: 0
UL_NPC
Integer
Number of packet calls during a session in uplink
Null column allowed: Yes Default value: 1
UL_SP
Integer
Packet size (Bytes) in uplink
Null column allowed: Yes Default value: 1500
UL_SPC_MAX
Float
Uplink maximum packet call size (kBytes)
Null column allowed: Yes Default value: 2000
UL_SPC_MIN
Float
Uplink minimum packet call size (kBytes)
Null column allowed: Yes Default value: 4
8.48 WServicesUsage Table For user profile parameters.
242
Field
Type
Description
Attributes
CALL_DURATION
Float
Average duration of a call (for circuit switched services) Unit: s
Null column allowed: Yes Default value:
CALL_NUMBER
Float
Average number of calls per hour for circuit switched services or average number of sessions per hour for packet switched services
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
DL_VOLUME
Float
Volume transferred on the downlink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
SERVICE
Text (50)
Service (from the Service table) that the subscriber can request
Null column allowed: No Default value:
TERMINAL
Text (50)
Type of terminal (from the Terminal table) used by the subscriber for the service
Null column allowed: No Default value:
UL_VOLUME
Float
Volume transferred on the uplink during a session (for packet switched services) Unit: Kbyte
Null column allowed: Yes Default value:
USER_PROFILE
Text (50)
User profile name
Null column allowed: No Default value:
8.49 WTerminals Table For terminal types. Field
Type
Description
Attributes
ANTENNA
Text (50)
Receiver's antenna name (if empty an omni antenna is used)
Null column allowed: Yes Default value:
DIVERSITY_SUPPORT
Short
Antenna diversity support (0 = None, 1 = AAS, 2 = MIMO, 3 = AAS+MIMO)
Null column allowed: Yes Default value: 1
GAIN
Float
Terminal antenna gain (dB)
Null column allowed: Yes Default value: 0
LOSS
Float
Terminal antenna loss (dB)
Null column allowed: Yes Default value: 0
MIMO_RX_ANTENNAS
Short
Number of MIMO antennas used for reception
Null column allowed: Yes Default value: 1
MIMO_TX_ANTENNAS
Short
Number of MIMO antennas used for transmission
Null column allowed: Yes Default value: 1
NAME
Text (50)
Terminal name
Null column allowed: No Default value:
NOISE_FACTOR
Float
Noise figure used to determine the thermal noise at the receiver (dB)
Null column allowed: Yes Default value: 8
PMAX
Float
Maximum terminal power on traffic channel (dBm)
Null column allowed: Yes Default value: 23
PMIN
Float
Minimum terminal power on traffic channel (dBm)
Null column allowed: Yes Default value: -22
RX_EQUIP
Text (50)
Name of the reception equipment available at the terminal
Null column allowed: Yes Default value:
SUPPORTED_LAYER_LIST
Text (50)
List of network layers supported by the terminal
Null column allowed: No Default value: “-1”
8.50 WTraficEnvironments Table For traffic environment clutter weighting. Field
Type
Description
Attributes
CLUTTER_WEIGHTS
Binary
Internal binary format describing weights assigned to each clutter class
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the created environment
Null column allowed: No Default value:
8.51 WUserProfiles Table For names of user profiles.
243
Atoll 3.2.1 Data Structure Reference Guide Chapter 8: WiMAX and Wi-Fi Data Structure
244
© Forsk 2014
Field
Type
Description
Attributes
NAME
Text (50)
Name of the created user profile
Null column allowed: No Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
9 Microwave Links Data Structure The Atoll Microwave module enables planning and optimisation of large backhaul networks according to ITU recommendations, industry standards, and operator-specific design guidelines. The following subsections list the tables in the Microwave Radio Links template data structure.
9.1 Data Structure Changes Between Atoll 3.1 and 3.2 9.1.1 Added Tables and Fields BHNodes Table (New) Field
Type
Description
Attributes
ACTIVE
Boolean
Flag to set in the node is in service or not
Null column allowed: Default value: True
COMMENT_
Text(255)
Comment
Null column allowed: Yes Default value:
NAME
Text(50)
Name of the node
Null column allowed: No Default value:
SITE
Text(50)
Relative to an existing site (cannot not be null)
Null column allowed: No Default value:
SUBNET
Text(50)
Name of a subnet (kind of user field, can be null)
Null column allowed: Yes Default value:
TRAFFIC_ETHDL
Float
Downlink data rate required by this node for packet traffic
Null column allowed: Yes Default value: 0
TRAFFIC_ETHUL
Float
Uplink data rate required by this node for packet traffic (Ethernet)
Null column allowed: Yes Default value: 0
TRAFFIC_TDM
Float
Data rate required by this node for circuit traffic (TDM)
Null column allowed: Yes Default value: 0
BHSegments Table (New) Field
Type
Description
Attributes
COMMENT_
Text(255)
Comment
Null column allowed: Yes Default value:
DEST_NODE
Text(80)
Destination of the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
SOURCE_NODE
Text(50)
Source of traffic demand on the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
TOPO_FLAG
Integer
Flag : 0 if "standard", 1 if it belongs to a ring topology
Null column allowed: Yes Default value: 0
BHSegmentsMedia Table (New) Field
Type
Description
Attributes
ACTIVE
Boolean
Flag to set in the medium is in service or not
Null column allowed: Default value: True
COMMENT_
Text(255)
Comment
Null column allowed: Yes Default value:
DEST_NODE
Text(255) Destination of the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
MWLINK
Text(120)
Medium. Relative to an existing microwave link (can be null)
Null column allowed: Default value:
NUM
Integer
Short number used to differentiate each medium, whatever MW table is in use (generated by Atoll)
Null column allowed: No Default value: 0
245
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
OTHER_TLINK
Text(120)
Medium. Relative to an existing non-microwave link (can be null)
Null column allowed: Yes Default value:
SOURCE_NODE
Text(255)
Source of the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
BANDWIDTH_ETH
Float
Capacity allocated by underlying media for Ethernet (in Mbps)
Null column allowed: Yes Default value: 0
BANDWIDTH_TDM
Float
Capacity allocated by underlying media for TDM (in Mbps)
Null column allowed: Yes Default value: 0
CustomFields Table Field
Type
Description
Attributes
DISPLAY_TYPE
Integer
0: Free; 1: Read-only
Null column allowed: Yes Default value: 0
MWBranchingConfigs Table Field
Type
Description
Attributes
LOS_MIMO
Boolean
Flag to define if this configuration supports LOS MIMO antennas
Null column allowed: No Default value: False
NUM_RX_ANTENNAS
Short
Number of receiving antennas (for MIMO)
Null column allowed: Yes Default value: 1
NUM_TX_ANTENNAS
Short
Number of transmitting antennas (for MIMO)
Null column allowed: Yes Default value: 1
MWCapacities Table Field
Type
Description
Attributes
ACM_MODE
Integer
Adaptive coding modulation type: 0 = none; 1 = Maximum system gain; 2 = Maximum Throughput
Null column allowed: Yes Default value: 0
CAPA_TECHNO
Short
Capacity configuration: 0 = Full packet; 1 = Hybrid; 2 = TDM only
Null column allowed: No Default value: 0
FAMILY
Text (50)
Table which defines the list of modulations supported by each family
Null column allowed: Yes Default value:
FREQ_BAND
Text (50)
Frequency band value
Null column allowed: Yes Default value:
MODULATION
Text (20)
Modulation name
Null column allowed: Yes Default value:
TDM_RATE
Float
Value of rate reserved for TDM in Mbps
Null column allowed: Yes Default value: 0
MWEquipments Table Field
Type
Description
Attributes
RX_LEVEL_REQUIRED
Integer
Value which defines the required received level for ATPC
Null column allowed: Yes Default value:
MWFamilyModulations Table Field
Type
Description
Attributes
LOW_POWER
Float
Low power value which can be used in link properties
Null column allowed: Yes Default value:
MWFrequencies Table (New)
246
Field
Type
Description
Attributes
CHANNEL_ID
Integer
ID of the channel
Null column allowed: No Default value: 1
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
CHANNEL_RADICAL
Text (20)
Radical of the channel. Sub-band prefix and suffix will be appended
Null column allowed: Yes Default value:
FREQ_L
Double
Value of the frequency (MHz) in the lower half-band
Null column allowed: Yes Default value:
FREQ_U
Double
Value of the frequency (MHz) in the upper half-band
Null column allowed: Yes Default value:
SUBBAND
Text (50)
Name of a existing sub-band to which these frequencies are related
Null column allowed: No Default value:
Description
Attributes
MWLinks Table Field
Type
POWER_FLAG_A
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
POWER_FLAG_B
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
TX_POWER_A
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Yes Default value: 0
TX_POWER_B
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Yes Default value: 0
MWMediumTypes Table (New) Field
Type
Description
Attributes
AIR_LINK_RATE
Float
Value of rate in Mbps
Null column allowed: Yes Default value: 100
CAPA_TECHNO
Short
Capacity configuration: 0 = Full packet, 1 = Hybrid, 2 = TDM only
Null column allowed: Yes Default value: 0
NAME
Text (20)
Name of the medium
Null column allowed: No Default value:
TDM_RATE
Float
Value of rate reserved for TDM in Mbps
Null column allowed: Yes Default value: 50
Description
Attributes
MWMultiHopsLinks Table Field
Type
IDENT
Short
Null column allowed: No Default value: 100
OTLINK
Text (120)
Null column allowed: Yes Default value: 50
MWOperatingModes Table (New) Field
Type
Description
Attributes
FULL_NAME
Text (50)
String describing the mode: displayed in the GUI wherever there is room for long strings (e.g. “Adaptive Coding Modulation”)
Null column allowed: No Default value: “Mode”
MODE_ID
Integer
Number used for managing relationships between related tables
Null column allowed: No Default value:
OPERATION_FLAG
Short
XOR of supported mode (00 = fix, 01 = with ACM)
Null column allowed: Yes Default value: 0
SHORT_NAME
Text (10)
String describing the mode: used for distinguishing active modulations in a link
Null column allowed: No Default value: “Mode”
247
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
MWOTLinks Table (New) Field
Type
Description
Attributes
ACTIVE
Boolean
Flag to filter links
Null column allowed: No Default value: True
COMMENT_
Text (255)
Comment
Null column allowed: Yes Default value:
EPO_CLASS
Text (50)
EPO class
Null column allowed: Yes Default value:
MEDIUM_TYPE
Text (20)
Medium type
Null column allowed: No Default value:
NAME
Text (120)
Name of the link
Null column allowed: No Default value:
SITE_A
Text (50)
Site A
Null column allowed: No Default value:
SITE_B
Text (50)
Site B
Null column allowed: No Default value:
MWSubbands Table Field
Type
Description
Attributes
PREFIX_L
Text (5)
Prefix for formatting channel in lower sub-band
Null column allowed: Yes Default value:
PREFIX_U
Text (5)
Prefix for formatting channel in upper sub-band
Null column allowed: Yes Default value:
SUFFIX_L
Text (5)
Suffix for formatting channel in lower sub-band
Null column allowed: Yes Default value:
SUFFIX_U
Text (5)
Suffix for formatting channel in upper sub-band
Null column allowed: Yes Default value:
MWTplLinks Table Field
Type
Description
Attributes
ACTIVE_MODULATIONS_A
Text (255)
List of modulations among family ones available for that link (null = All)
Null column allowed: Yes Default value:
ACTIVE_MODULATIONS_B
Text (255)
List of modulations among family ones available for that link (null = All)
Null column allowed: Yes Default value:
ANTENNA2_A
Text (50) Diversity antenna on site A (antenna used for B >> A, when A is receiver)
Null column allowed: Yes Default value:
ANTENNA2_B
Text (50) Diversity antenna on site B (antenna used for A >> B, when B is receiver)
Null column allowed: Yes Default value:
FREQ_SUBBAND
Text (50)
Type of channelisation within the selected frequency band for A >> B
Null column allowed: Yes Default value:
FREQ_SUBBAND_B
Text (50)
Type of channelisation within the selected frequency band for B >> A
Null column allowed: Yes Default value:
GEOCLIM_FACTOR
Double
Geoclimatic factor used for Rec ITU-530
Null column allowed: Yes Default value:
POWER_FLAG_A
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
POWER_FLAG_B
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
SEPARATION_A
Float
Distance between antenna and diversity antenna (siteA receiver)
Null column allowed: Yes Default value: 0
SEPARATION_B
Float
Distance between antenna and diversity antenna (siteB receiver)
Null column allowed: Yes Default value: 0
TX_POWER_A
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Yes Default value: 0
248
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
TX_POWER_B
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Yes Default value: 0
Field
Type
Description
Attributes
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
Sites Table
9.1.2 Deleted Tables and Fields MWEquipments Table •
RX_LEVEL_REQUIRED
MWLinks Table • •
USE_STD_POWER_A USE_STD_POWER_B
MWMultiHopsLinks Table •
ORDER_
Sites Table •
SUPPORT_NATURE
9.2 BHNodes Table Field
Type
Description
Attributes
ACTIVE
Boolean
Flag to set in the node is in service or not
Null column allowed: Default value: True
COMMENT_
Text(255)
Comment
Null column allowed: Yes Default value:
NAME
Text(50)
Name of the node
Null column allowed: No Default value:
SITE
Text(50)
Relative to an existing site (cannot not be null)
Null column allowed: No Default value:
SUBNET
Text(50)
Name of a subnet (kind of user field, can be null)
Null column allowed: Yes Default value:
TRAFFIC_ETHDL
Float
Downlink data rate required by this node for packet traffic
Null column allowed: Yes Default value: 0
TRAFFIC_ETHUL
Float
Uplink data rate required by this node for packet traffic (Ethernet)
Null column allowed: Yes Default value: 0
TRAFFIC_TDM
Float
Data rate required by this node for circuit traffic (TDM)
Null column allowed: Yes Default value: 0
9.3 BHSegments Table Field
Type
Description
Attributes
COMMENT_
Text(255)
Comment
Null column allowed: Yes Default value:
DEST_NODE
Text(80)
Destination of the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
SOURCE_NODE
Text(50)
Source of traffic demand on the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
249
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
TOPO_FLAG
Integer
Flag : 0 if "standard", 1 if it belongs to a ring topology
Null column allowed: Yes Default value: 0
9.4 BHSegmentsMedia Table Field
Type
Description
Attributes
ACTIVE
Boolean
Flag to set in the medium is in service or not
Null column allowed: Default value: True
COMMENT_
Text(255)
Comment
Null column allowed: Yes Default value:
DEST_NODE
Text(255) Destination of the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
MWLINK
Text(120)
Medium. Relative to an existing microwave link (can be null)
Null column allowed: Default value:
NUM
Integer
Short number used to differentiate each medium, whatever MW table is in use (generated by Atoll)
Null column allowed: No Default value: 0
OTHER_TLINK
Text(120)
Medium. Relative to an existing non-microwave link (can be null)
Null column allowed: Yes Default value:
SOURCE_NODE
Text(255)
Source of the segment. Relative to an existing node (cannot be null)
Null column allowed: No Default value:
BANDWIDTH_ETH
Float
Capacity allocated by underlying media for Ethernet (in Mbps)
Null column allowed: Yes Default value: 0
BANDWIDTH_TDM
Float
Capacity allocated by underlying media for TDM (in Mbps)
Null column allowed: Yes Default value: 0
9.5 CoordSys Table For the projection coordinate system and the database’s internal coordinate system (this is the display coordinate system used when creating a database).
250
Field
Type
Description
Attributes
CODE
Integer
Identification number of the coordinate system (the code of userdefined coordinate systems is an integer higher than 32768)
Null column allowed: No Default value: 0
DATUM_CODE
Double
DATUM_ROTX
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTY
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_ROTZ
Double
Arc-seconds
Null column allowed: Yes Default value: 0
DATUM_SCALE
Double
Parts per million (ppm)
Null column allowed: Yes Default value: 0
DATUM_SHIFTX
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTY
Double
Meters
Null column allowed: Yes Default value: 0
DATUM_SHIFTZ
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_CODE
Integer
ELLIPS_RMAJOR
Double
Meters
Null column allowed: Yes Default value: 0
ELLIPS_RMINOR
Double
Meters
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
Null column allowed: No Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
NAME
Text (50)
Coordinate system name
Null column allowed: No Default value:
PROJ_ANGLE
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_FALSE_EASTING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FALSE_NORTHING
Double
Meters
Null column allowed: Yes Default value: 0
PROJ_FIRST_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LATITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_LONGITUDE_ORIGIN
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_METHOD
Short
UTM, Undefined, NoProjection, Lambert1SP, Lambert2SP, Mercator, CassiniSoldner, TransMercator, TransMercatorSO, ObliqueStereographic, NewZealandMapGrid, HotineOM, LabordeOM, SwissObliqueCylindical
Null column allowed: Yes Default value: 0
PROJ_SCALE_FACTOR
Double
PROJ_SECOND_PARALLEL
Double
Decimal degrees
Null column allowed: Yes Default value: 0
PROJ_ZONE_NUMBER
Integer
Used with UTM
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value: 0
9.6 CustomFields Table For defining user-defined fields added to tables, default values for any field (including user-defined fields), and choice lists, captions, and group names for user-defined fields. Field
Type
Description
Attributes
CAPTION
Text (50)
Caption of the field (displayed instead of the name)
Null column allowed: Yes Default value:
CHOICE_LIST
Memo
Choice list for the field
Null column allowed: Yes Default value:
CHOICE_TYPE
Integer
0=Choice list is optional; 1=Choice list is mandatory
Null column allowed: Yes Default value: 0
COLUMN_NAME
Text (50)
Second part of the unique key. Field name
Null column allowed: No Default value:
DEFAULT_VALUE
Text (50)
Default value for the field
Null column allowed: Yes Default value:
DISPLAY_TYPE
Integer
0: Free; 1: Read-only
Null column allowed: Yes Default value: 0
GROUP_NAME
Text (50)
Name of the group to which that field belongs
Null column allowed: Yes Default value:
TABLE_NAME
Text (50)
First part of the unique key. Table name
Null column allowed: No Default value:
These are some general recommendations that you should follow when handling databases. General • • • •
In order to use Atoll with Oracle, you must create Oracle users and schema with names in uppercase. Create backups of the database before upgrading. It is recommended to define a rule for making backups of the database at regular intervals. Do not skip a major Atoll version. For example, if you are currently using Atoll 2.7.xV6.7, you should first upgrade the database to Atoll 2.8.xV6.9 before upgrading to Atoll 3.1.xV7.1.
251
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Upgrading your database will be simpler if you do not skip a major version. If you skip or have skipped an intermediate major version, you must upgrade your database twice in order to make it compatible with the new version. Tables and Fields • •
Table and field names are case sensitive. Table and field names should be not more than 20 characters long. Oracle databases allow a maximum length of 30 characters for field and table names. However, for use in Atoll, you must not create tables and fields with names longer than 20 characters. This is because Atoll adds some characters to the table and field names for certain operations: creating associated triggers, creating project databases, etc. Limiting the length of table and field names to 20 characters will help avoid database connection and consistency problems.
• • • • • •
• •
Table and field names should only use alphanumeric characters (A-Z, a-z, 0-9) and underscores (_). Table and field names must not start with a numeric character (0-9). Table and field names must not contain an SQL or RDBMS-specific keyword, such as ORDER, DATE, etc. Table and field names must not contain spaces or special characters, such as periods (.), exclamation marks (!), colons (:), semi-colons (;), interrogation marks (?), parentheses (()), brackets ({}), square brackets ([]), etc. Boolean fields, system or user-defined, should always have default values assigned. The CustomFields table enables you to define default values, choice lists, and read/write access for any field in any table in Atoll, including user-defined fields that you add to the Atoll tables. The values defined in this table have priority over the internal predefined default values. If you define floating point default values, make sure that all the users have the same decimal separator. If you wish to add custom fields in the Atoll document, you should first add the field in the database, and then update your Atoll document from the database. When setting up your database for the first time, try to anticipate user requirements in terms of custom fields in Atoll tables. Some requirements of the different user groups can be satisfied if a few general-purpose user-defined fields are added in Atoll tables when setting up the database. For example, if you add three user-defined fields (one of type integer, float, and text (limited size)) to the Sites and Transmitters tables, users will be able to use these for sorting, filtering, grouping, or other purposes. This approach can help the database function a long time before users require the addition of other custom fields.
• •
•
To improve performance, if your projects allow it, reduce the size of the fields corresponding to the sites and transmitters’ names. To improve performance, unless absolutely necessary, do not add user-defined fields of Text type. Rather, use numeric field types, which allow sorting and other functions. If you must add Text fields, allocate them the appropriate size that would suffice. For example, a 255-character long Text type field would, for the most part, occupy disk space for no purpose. To improve performance, you should avoid adding custom fields to the neighbour management tables.
9.7 MWAntennas Table For microwave antennas.
252
Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DIAMETER
Float
Diameter of the antenna
Null column allowed: Yes Default value: 5
FREQ_BAND
Text (50)
Frequency band of the antenna
Null column allowed: No Default value:
GAIN
Float
Antenna gain
Null column allowed: Yes Default value: 10
MANUFACTURER
Text (50)
Manufacturer of the antenna
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the antenna
Null column allowed: No Default value:
PATTERN
Binary
Antenna pattern diagrams
Null column allowed: Yes Default value:
RADOME_LOSS
Float
Radome loss to take into account when radomes are used on links
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
The format of the binary field, PATTERN, is described in "Microwave 2D Antenna Pattern Format" on page 277.
9.8 MWBands Table For microwave frequency bands. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
FMAX
Double
Maximum frequency
Null column allowed: Yes Default value: 200
FMIN
Double
Minimum frequency
Null column allowed: Yes Default value: 100
NAME
Text (50)
Name of the frequency band
Null column allowed: No Default value:
9.9 MWBranchingConfigs Table For microwave branching configurations. Field
Type
Description
Attributes
FREQ_DIVERSITY
Boolean
Flag to check if this configuration supports frequency diversity
Null column allowed: No Default value: False
HSB
Boolean
Flag to check if this configuration supports hot standby
Null column allowed: No Default value: False
LOS_MIMO
Boolean
Flag to define if this configuration supports LOS MIMO antennas
Null column allowed: No Default value: False
NAME
Text (50)
Branching configuration name
Null column allowed: No Default value:
NUM_RX_ANTENNAS
Short
Number of receiving antennas (for MIMO)
Null column allowed: Yes Default value: 1
NUM_TX_ANTENNAS
Short
Number of transmitting antennas (for MIMO)
Null column allowed: Yes Default value: 1
SPACE_DIVERSITY
Boolean
Flag to check if this configuration supports space diversity
Null column allowed: No Default value: False
SYSTEM_CONFIG_M
Short
Maximum number of standby channels which can be branched
Null column allowed: Yes Default value: 0
SYSTEM_CONFIG_N
Short
Maximum number of main channels which can be branched
Null column allowed: Yes Default value: 1
XPIC
Boolean
Flag to check if this configuration supports cross polar cancellation
Null column allowed: No Default value: False
9.10 MWCapacities Table For microwave data rates. Field
Type
Description
Attributes
ACM_MODE
Integer
Adaptive coding modulation type: 0 = none; 1 = Maximum system gain; 2 = Maximum Throughput
Null column allowed: Yes Default value: 0
AIR_LINK_RATE
Float
Data rate
Null column allowed: Yes Default value: 0
CAPA_TECHNO
Short
Capacity configuration: 0 = Full packet; 1 = Hybrid; 2 = TDM only
Null column allowed: No Default value: 0
253
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
FAMILY
Text (50)
Table which defines the list of modulations supported by each family
Null column allowed: Yes Default value:
FREQ_BAND
Text (50)
Frequency band value
Null column allowed: Yes Default value:
MODULATION
Text (20)
Modulation name
Null column allowed: Yes Default value:
NAME
Text (50)
Capacity name
Null column allowed: No Default value:
TDM_RATE
Float
Value of rate reserved for TDM in Mbps
Null column allowed: Yes Default value:
9.11 MWCompatibilities Table For compatibility mapping between equipment and antennas. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna
Null column allowed: No Default value:
CAPA_TECHNO
Short
Capacity configuration: 0 = Full packet; 1 = Hybrid; 2 = TDM only
Null column allowed: No Default value: 0
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
EQUIPMENT
Text (50)
Name of the equipment
Null column allowed: No Default value:
9.12 MWCompatibilitiesGuides Table For compatibility mapping between wave guides and antennas. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the antenna
Null column allowed: No Default value:
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
GUIDE
Text (50)
Name of the wave guide
Null column allowed: No Default value:
9.13 MWDefaultsCurves Table For default graphs of transmission and reception masks, etc. Field
254
Type
Description
Attributes
BANDWIDTH
Float
Channel bandwidth
Null column allowed: Yes Default value: 0
CURVE_TYPE
Short
The type of curve Choice list: 0=TX_MASK; 1=RX_MASK; 2=TtoI;
Null column allowed: Yes Default value: 0
FREQ_BAND
Text (50)
Frequency band
Null column allowed: No Default value:
INTERFERED
Text (50)
MANUFACTURER
Text (50)
Manufacturer
Null column allowed: Yes Default value:
MODULATION
Text (20)
Modulation used
Null column allowed: Yes Default value:
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
NAME
Text (50)
Name of the curve
Null column allowed: No Default value:
RATE
Float
Rate (Mbps)
Null column allowed: Yes Default value: 1
VALUES_
Memo
Curve values
Null column allowed: Yes Default value:
9.14 MWEPO Table For quality and availability performance objectives. Field
Type
Description
Attributes
A
Double
Parameter used to calculate the EPO required: EPO = A * L+B
Null column allowed: No Default value: 0
B
Double
Parameter used to calculate the EPO required: EPO = A * L+B
Null column allowed: No Default value: 0
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
EPO_PARAM
Text (5)
Performance objective parameter (SESR, BBER, or ESR)
Null column allowed: No Default value:
EPO_TYPE
Text (1)
Performance objective type (yAvailability or Quality)
Null column allowed: No Default value:
LINK_CLASS
Text (50)
EPO Link class
Null column allowed: No Default value:
MAXIMUM_LENGTH
Double
Maximum length of link related to an objective (km)
Null column allowed: Yes Default value: 0
MINIMUM_LENGTH
Double
Maximum length of link related to an objective (km)
Null column allowed: Yes Default value: 0
NAME
Text (50)
EPO name
Null column allowed: No Default value:
RATE_MAX
Float
Maximum bit rate (Mbps)
Null column allowed: Yes Default value:
RATE_MIN
Float
Minimum bit rate (Mbps)
Null column allowed: Yes Default value:
REC_UIT
Float
ITU Recommendations
Null column allowed: Yes Default value: 1
9.15 MWEPOLinkClass Table For EPO link classes. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
LINK_CLASS
Text (5)
Type of EPO link class
Null column allowed: No Default value:
LINK_SUBCLASS
Text (5)
Type of EPO link subclass
Null column allowed: Yes Default value:
LMAX
Float
Maximum length of the link for the EPO class
Null column allowed: Yes Default value:
LMIN
Float
Minimum length of the link for the EPO class
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the EPO class
Null column allowed: No Default value:
255
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
9.16 MWEquipments Table For microwave radios. Field
Type
Description
Attributes
ACM_MODE
Integer
Optimisation mode: 0=None; 1=Max system gain; 2=Max throughput gain;
Null column allowed: No Default value: 0
CAPACITY
Text (50)
Equipment capacity
Null column allowed: No Default value: 1
CHANNEL_SPACING
Text (50)
Channel spacing defined by the manufacturer for this capactiy/ modulation
Null column allowed: Yes Default value:
CI_MIN_BER3
Float
Minimum C/I for BER = 1e-3
Null column allowed: Yes Default value:
CI_MIN_BER6
Float
Minimum C/I for BER = 1e-6
Null column allowed: Yes Default value:
DFM
Memo
Dispersive fade margin curve
Null column allowed: Yes Default value:
EMISSION_DESIGNATOR
Text (20)
Normalized designator
Null column allowed: Yes Default value:
FAMILY
Text (50)
Family name
Null column allowed: No Default value:
FREQ_BAND
Text (50)
Frequency band of the equipment
Null column allowed: No Default value:
HSB_DELAY
Float
Hot Standby commutation delay time
Null column allowed: Yes Default value: 0
IFM
Float
Margin against interference
Null column allowed: Yes Default value: 1
KN
Float
Kn parameter
Null column allowed: Yes Default value: 0
MIN_PHASE_SIG_DEPTH
Memo
Minimum signature depth
Null column allowed: Yes Default value: '1e-6 30 1e-3 30'
MIN_PHASE_SIG_WIDTH
Memo
Minimum signature width
Null column allowed: Yes Default value: '1e-6 10 1e-3 10'
MODULATION
Text (20)
Modulation type
Null column allowed: No Default value: “16-QAM”
MTBF
Float
Mean Time Before Failure
Null column allowed: Yes Default value: 1000000
NAME
Text (50)
Name of the equipment
Null column allowed: No Default value:
NF
Float
Noise Figure of the equipment
Null column allowed: Yes Default value: 5
NON_MIN_PHASE_SIG_DEPT H
Memo
Non minimum signature depth
Null column allowed: Yes Default value: '1e-6 30 1e-3 30'
NON_MIN_PHASE_SIG_WID TH
Memo
Non minimum signature width
Null column allowed: Yes Default value: '1e-6 10 1e-3 10'
RX_LOSS_PHYS
Float
Physical receiver loss
Null column allowed: Yes Default value: 0
RX_OVERFLOW
Memo
Curve which defines the thresholds max value for any value of BER
Null column allowed: Yes Default value: '1e-6 -25 1e-3 -20'
RX_PORT_1
Float
Receiving loss on port number 1
Null column allowed: Yes Default value: 0
256
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
RX_PORT_2
Float
Receiving loss on port number 2
Null column allowed: Yes Default value: 0
RX_PORT_3
Float
Receiving loss on port number 3
Null column allowed: Yes Default value: 0
RX_PORT_4
Float
Receiving loss on port number 4
Null column allowed: Yes Default value: 0
RX_PORT_5
Float
Receiving loss on port number 5
Null column allowed: Yes Default value: 0
RX_PORT_6
Float
Receiving loss on port number 16
Null column allowed: Yes Default value: 0
RX_PORT_7
Float
Receiving loss on port number 7
Null column allowed: Yes Default value: 0
RX_PORT_8
Float
Receiving loss on port number 8
Null column allowed: Yes Default value: 0
RX_PORT_9
Float
Receiving loss on port number 9
Null column allowed: Yes Default value: 0
RX_PORT_10
Float
Receiving loss on port number 10
Null column allowed: Yes Default value: 0
RX_SELECTIVITY
Memo
Receiver filter selectivity
Null column allowed: Yes Default value:
RX_SENSITIVITY
Memo
BER - Sensitivity tables
Null column allowed: Yes Default value: “1e-6 -82 1e-3 -90”
TI_CURVE
Memo
T/I curve
Null column allowed: Yes Default value:
TX_LOSS_PHYS
Float
Physical transmitter loss
Null column allowed: Yes Default value: 0
TX_MASK
Memo
Transmitter spectrum mask
Null column allowed: Yes Default value:
TX_PORT_1
Float
Transmission loss on port number 1
Null column allowed: Yes Default value: 0
TX_PORT_2
Float
Transmission loss on port number 2
Null column allowed: Yes Default value: 0
TX_PORT_3
Float
Transmission loss on port number 3
Null column allowed: Yes Default value: 0
TX_PORT_4
Float
Transmission loss on port number 4
Null column allowed: Yes Default value: 0
TX_PORT_5
Float
Transmission loss on port number 5
Null column allowed: Yes Default value: 0
TX_PORT_6
Float
Transmission loss on port number 6
Null column allowed: Yes Default value: 0
TX_PORT_7
Float
Transmission loss on port number 7
Null column allowed: Yes Default value: 0
TX_PORT_8
Float
Transmission loss on port number 8
Null column allowed: Yes Default value: 0
TX_PORT_9
Float
Transmission loss on port number 9
Null column allowed: Yes Default value: 0
TX_PORT_10
Float
Transmission loss on port number 10
Null column allowed: Yes Default value: 0
WITH_EQUALIZER
Boolean
Used to calculate Kn
Null column allowed: No Default value: False
XPIF
Float
Crosspolar Interference Factor
Null column allowed: Yes Default value: 20
257
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
9.17 MWFamilies Table For microwave radio families. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
MANUFACTURER
Text (50)
Manufacturer name
Null column allowed: Yes Default value:
NAME
Text (50)
Family name
Null column allowed: No Default value:
9.18 MWFamilyBands Table For frequency bands supported by microwave radio families. Field
Type
Description
Attributes
ACM_MODE
Integer
Optimisation mode: 0=None; 1=Max system gain; 2=Max throughput gain;
Null column allowed: No Default value: 0
FAMILY
Text (50)
Family name
Null column allowed: No Default value:
FREQ_BAND
Text (50)
Frequency band
Null column allowed: No Default value:
9.19 MWFamilyBrConfigs Table For branching configurations supported by microwave radio families. Field
Type
Description
Attributes
BRANCHING_CONFIG
Text (50)
Branching configuration name
Null column allowed: No Default value:
FAMILY
Text (50)
Family name
Null column allowed: No Default value:
FREQ_BAND
Text (50)
Frequency band
Null column allowed: No Default value:
RX_BRLOSS
Float
Main channel reception loss
Null column allowed: Yes Default value: 0
RX_STANDBY_LOSS
Float
Standby channel reception loss
Null column allowed: Yes Default value: 0
TX_BRLOSS
Float
Transmission loss
Null column allowed: Yes Default value: 0
9.20 MWFamilyChSpacings Table For channel widths supported by microwave radio families.
258
Field
Type
Description
Attributes
CHANNEL_SPACING
Text (50)
Channel spacing name
Null column allowed: No Default value:
FAMILY
Text (50)
Family name
Null column allowed: No Default value:
FREQ_BAND
Text (50)
Frequency band
Null column allowed: No Default value:
XS
Double
Channel spacing in MHz
Null column allowed: Yes Default value: 7
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
9.21 MWFamilyModulations Table For modulations supported by microwave radio families. Field
Type
Description
Attributes
ACM_MODE
Integer
Optimisation mode: 0=None; 1=Max system gain; 2=Max throughput gain;
Null column allowed: No Default value: 0
ATPC_MAX
Float
Maximum supported ATPC value
Null column allowed: Yes Default value:
ATPC_STEP
Float
ATPC interval
Null column allowed: Yes Default value:
DISCRETE_POWERS
Text (255)
Allowed power values
Null column allowed: Yes Default value:
FAMILY
Text (50)
Family name
Null column allowed: No Default value:
FREQ_BAND
Text (50)
Frequency bands
Null column allowed: No Default value:
LOW_POWER
Float
Low power value which can be used in link properties
Null column allowed: Yes Default value:
MAX_POWER
Float
Maximum power
Null column allowed: Yes Default value: 30
MODULATION
Text (20)
Modulation
Null column allowed: No Default value:
STD_POWER
Float
Standard power
Null column allowed: Yes Default value:
9.22 MWFrequencies Table For microwave frequencies. Field
Type
Description
Attributes
CHANNEL_ID
Integer
ID of the channel
Null column allowed: No Default value: 1
CHANNEL_RADICAL
Text (20)
Radical of the channel. Sub-band prefix and suffix will be appended
Null column allowed: Yes Default value:
FREQ_L
Double
Value of the frequency (MHz) in the lower half-band
Null column allowed: Yes Default value:
FREQ_U
Double
Value of the frequency (MHz) in the upper half-band
Null column allowed: Yes Default value:
SUBBAND
Text (50)
Name of a existing sub-band to which these frequencies are related
Null column allowed: No Default value:
9.23 MWGuides Table For microwave wave guides. Field
Type
Description
Attributes
FREQ_BAND
Text (50)
Frequency band of the guide
Null column allowed: No Default value:
GUIDE_TYPE
Integer
Type of guide: 0=Cable; 1=Elliptic; 2=Rectangular; 3=Circular; 4=Other;
Null column allowed: Yes Default value: 0
LOSS_PER_METER
Float
Linear loss
Null column allowed: Yes Default value: 7
MANUFACTURER
Text (50)
Guide manufacturer
Null column allowed: Yes Default value:
259
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
NAME
Text (50)
Name of the guide
Null column allowed: No Default value:
9.24 MWHubs Table For microwave link hubs. Field
Type
Description
Attributes
ANTENNA
Text (50)
Name of the (shared) Antenna
Null column allowed: Yes Default value:
AZIMUTH
Float
Azimuth of the Antenna
Null column allowed: Yes Default value: 0
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DOWNTILT
Float
Tilt of the Antenna
Null column allowed: Yes Default value: 0
FREQ_BAND
Text (50)
Name of the frequency band
Null column allowed: No Default value:
HEIGHT
Float
Height of the Antenna
Null column allowed: Yes Default value: 30
NAME
Text (50)
Name of the Hub
Null column allowed: No Default value:
PMP_TYPE
Short
Type of the PMP: TDA or FDA
Null column allowed: Yes Default value: 0
SITE
Text (50)
Name of the site
Null column allowed: No Default value:
9.25 MWIrfs Table For interference reduction factors per microwave equipment pairs. Field
Type
Description
Attributes
INTERFERED
Text (50)
Interfered equipment
Null column allowed: No Default value:
INTERFERER
Text (50)
Interferer equipment
Null column allowed: No Default value:
IRF
Memo
List of interference filtering protections
Null column allowed: Yes Default value:
The IRF field represents a list of pairs of values. Each pair consists of: • •
float deltaF: spacing in frequency float protection: protection applied to this frequency
9.26 MWLinks Table For microwave links. Field
Type
Description
Attributes
ACTIVE
Boolean
Link active or not
Null column allowed: No Default value: True
ACTIVE_MODULATIONS_A
Text (255)
List of modulations used at A
Null column allowed: Yes Default value:
ACTIVE_MODULATIONS_B
Text (255)
List of modulations used at B
Null column allowed: Yes Default value:
260
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
ANTENNA_A
Text (50)
Main antenna at site A
Null column allowed: Yes Default value:
ANTENNA_B
Text (50)
Main antenna at site B
Null column allowed: Yes Default value:
ANTENNA2_A
Text (50)
Secondary antenna at site A
Null column allowed: Yes Default value:
ANTENNA2_B
Text (50)
Secondary antenna at site B
Null column allowed: Yes Default value:
ATMOS_PRESSURE
Float
Atmospheric pressure in mbar
Null column allowed: Yes Default value:
ATPC_A
Float
ATPC at site A
Null column allowed: Yes Default value: 0
ATPC_B
Float
ATPC at site B
Null column allowed: Yes Default value: 0
AZIMUTH_A
Float
Azimuth at site A
Null column allowed: Yes Default value: 0
AZIMUTH_B
Float
Azimuth at site B
Null column allowed: Yes Default value: 0
BER
Double
Bit Error Rate
Null column allowed: Yes Default value: 1e-3
BER2
Double
Second Bit Error Ratio (i.e. 1e-6)
Null column allowed: Yes Default value: 1e-6
BRANCHING_CONFIG_A
Text (50)
Branching configuration at A
Null column allowed: Yes Default value:
BRANCHING_CONFIG_B
Text (50)
Branching configuration at B
Null column allowed: Yes Default value:
C_FACTOR
Float
Vigants-Barnett method: C factor
Null column allowed: Yes Default value: 1
CHANNELS_A
Text (50)
Channels used at site A
Null column allowed: Yes Default value:
CHANNELS_B
Text (50)
Channels used at site B
Null column allowed: Yes Default value:
CLIMATE_ZONE
Short
Rain Climate Zone
Null column allowed: Yes Default value: 4
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
DELTA_POW_A
Float
Gain or loss to maximum transmitter power at A
Null column allowed: Yes Default value: 0
DELTA_POW_B
Float
Gain or loss to maximum transmitter power at B
Null column allowed: Yes Default value: 0
DOWNTILT_A
Float
Downtilt at site A
Null column allowed: Yes Default value: 0
DOWNTILT_B
Float
Downtilt at site B
Null column allowed: Yes Default value: 0
DX_A
Float
X coordinate relative to the site A position
Null column allowed: Yes Default value: 0
DX_B
Float
X coordinate relative to the site B position
Null column allowed: Yes Default value: 0
DY_A
Float
Y coordinate relative to the site A position
Null column allowed: Yes Default value: 0
DY_B
Float
Y coordinate relative to the site B position
Null column allowed: Yes Default value: 0
ENVTYPE
Integer
Type of environment
Null column allowed: Yes Default value: 0
261
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
262
© Forsk 2014
Field
Type
Description
Attributes
EPO_CLASS
Text (50)
EPO Class for the link
Null column allowed: Yes Default value:
EQUIPMENT_A
Text (50)
Equipment at site A
Null column allowed: Yes Default value:
EQUIPMENT_B
Text (50)
Equipment at site B
Null column allowed: Yes Default value:
FREQ_A
Double
Frequency at site A
Null column allowed: Yes Default value: -1
FREQ_B
Double
Frequency at site B
Null column allowed: Yes Default value: -1
FREQ_BAND
Text (50)
Frequency band of the link
Null column allowed: No Default value:
FREQ_SUBBAND
Text (50)
Frequency subband of the link (site A)
Null column allowed: Yes Default value:
FREQ_SUBBAND_B
Text (50)
Frequency subband of the link (site B)
Null column allowed: Yes Default value:
GEOCLIM_FACTOR
Double
GUIDE_LG1
Float
Length of GUIDE1
Null column allowed: Yes Default value: 0
GUIDE_LG2
Float
Length of GUIDE2
Null column allowed: Yes Default value: 0
GUIDE_LG3
Float
Length of GUIDE3
Null column allowed: Yes Default value: 0
GUIDE_LG4
Float
Length of GUIDE4
Null column allowed: Yes Default value: 0
GUIDE_USE1
Integer
Use of Guide 1 on site A
Null column allowed: Yes Default value: 0
GUIDE_USE2
Integer
Use of Guide 2 on site B
Null column allowed: Yes Default value: 1
GUIDE_USE3
Integer
Use of Guide 1 on site B
Null column allowed: Yes Default value: 0
GUIDE_USE4
Integer
Use of Guide 2 on site A
Null column allowed: Yes Default value: 1
GUIDE1
Text (50)
Waveguide when A transmitting
Null column allowed: Yes Default value:
GUIDE2
Text (50)
Waveguide when B receiving
Null column allowed: Yes Default value:
GUIDE3
Text (50)
Waveguide when B transmitting
Null column allowed: Yes Default value:
GUIDE4
Text (50)
Waveguide when A receiving
Null column allowed: Yes Default value:
HEIGHT_A
Float
Height at site A
Null column allowed: Yes Default value: 0
HEIGHT_B
Float
Height at site B
Null column allowed: Yes Default value: 0
KQ_FACTOR
Float
KQ reliability method: KQ Factor
Null column allowed: Yes Default value:
MTTR
Float
Minimum Time To Repair
Null column allowed: Yes Default value: 0
NAME
Text (120)
Name of the microwave link
Null column allowed: No Default value:
PARITY_A
Integer
Parity of site A
Null column allowed: Yes Default value: 0
Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
PARITY_B
Integer
Parity of site B
Null column allowed: Yes Default value: 0
PL
Float
POLARIZATION_A
Text (1)
Polarization at site A
Null column allowed: Yes Default value: ‘V’
POLARIZATION_B
Text (1)
Polarization at site B
Null column allowed: Yes Default value: ‘V’
POWER_FLAG_A
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
POWER_FLAG_B
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
PROFILE
Binary
Link profile
Null column allowed: Yes Default value:
PROPAG_IMODEL
Text (50)
Propagation model used for interference calculation
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (50)
Propagation model
Null column allowed: Yes Default value:
R001
Float
Rain intensity exceeded for 0.01% of time (mm/hr)
Null column allowed: Yes Default value:
RADOME_ON_A
Boolean
Radome used on the first antenna at A
Null column allowed: No Default value: False
RADOME_ON_B
Boolean
Radome used on the first antenna at B
Null column allowed: No Default value: False
RADOME2_ON_A
Boolean
Radome used on the second antenna at A
Null column allowed: No Default value: False
RADOME2_ON_B
Boolean
Radome used on the second antenna at B
Null column allowed: No Default value: False
RAIN_HEIGHT
Float
RAIN_ZONE
Short
REFRACTIVITY
Float
REFRACTIVITY_KE
Float
N-units /km
Null column allowed: Yes Default value:
REPEATER1
Text (50)
First repeater (P)
Null column allowed: Yes Default value:
REPEATER2
Text (50)
Second repeater (Q)
Null column allowed: Yes Default value:
RXLOSS_ATT_A
Float
Reception losses due to attenuators at A
Null column allowed: Yes Default value: 0
RXLOSS_ATT_B
Float
Reception losses due to attenuators at B
Null column allowed: Yes Default value: 0
SEPARATION_A
Float
Diversity separation at site A
Null column allowed: Yes Default value: 0
SEPARATION_B
Float
Diversity separation at site B
Null column allowed: Yes Default value: 0
SHIELDING_FACTOR_A
Float
Additional loss due to a natural or artificial obstacle in the vicinity of the Null column allowed: Yes antenna A Default value: 0
SHIELDING_FACTOR_B
Float
Additional loss due to a natural or artificial obstacle in the vicinity of the Null column allowed: Yes antenna B Default value: 0
SITE_A
Text (50)
Null column allowed: Yes Default value: 10
Null column allowed: Yes Default value: Rain zone
Null column allowed: Yes Default value: 4 Null column allowed: Yes Default value:
Site of departure (A)
Null column allowed: No Default value:
263
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
SITE_B
Text (50)
Site of arrival (B)
Null column allowed: No Default value:
TEMPERATURE
Float
Temperature
Null column allowed: Yes Default value:
TERRAIN_TYPE
Integer
Terrain type (Vigants)
Null column allowed: Yes Default value: 0
TX_POWER_A
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Default value: 0
TX_POWER_B
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Default value: 0
TXLOSS_ATT_A
Float
Transmission losses due to attenuators at A
Null column allowed: Yes Default value: 0
TXLOSS_ATT_B
Float
Transmission losses due to attenuators at B
Null column allowed: Yes Default value: 0
TXLOSS_BRANCHING_A
Float
Transmission losses due to connectors and branching at A
Null column allowed: Yes Default value: 0
TXLOSS_BRANCHING_B
Float
Transmission losses due to connectors and branching at B
Null column allowed: Yes Default value: 0
VAPOR
Float
Vapour density (g/cu. m)
Null column allowed: Yes Default value:
9.27 MWLinkTypes Table For types of microwave link trunks. Field
Type
Description
Attributes
BER_SES
Double
BERses
Null column allowed: Yes Default value: 0
BLOCK_SIZE
Integer
Size of transmitted blocks (number of bits per block)
Null column allowed: Yes Default value: 2000
NAME
Text (50)
Name of the link type
Null column allowed: No Default value:
RATE
Float
Maximum bit rate (Mbps)
Null column allowed: Yes Default value: 2
SUP_RATE
Float
Supported bit rate (Mbps)
Null column allowed: Yes Default value: 2
TYPE
Short
Trunk type: 0=PDH; 1=SDH; 2=IP;
Null column allowed: Yes Default value: 0
9.28 MWManufacturers Table For microwave equipment manufacturers. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the manufacturer
Null column allowed: No Default value:
9.29 MWMediumTypes Table For medium types.
264
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
AIR_LINK_RATE
Float
Value of rate in Mbps
Null column allowed: Yes Default value: 100
CAPA_TECHNO
Short
Capacity configuration: 0 = Full packet, 1 = Hybrid, 2 = TDM only
Null column allowed: Yes Default value: 0
NAME
Text (20)
Name of the medium
Null column allowed: No Default value:
TDM_RATE
Float
Value of rate reserved for TDM in Mbps
Null column allowed: Yes Default value: 50
9.30 MWModulations Table For modulations. Field
Type
Description
Attributes
EB_N0
Memo
Eb/No graph
Null column allowed: Yes Default value:
FULL_NAME
Text (255)
Comments
Null column allowed: Yes Default value:
NAME
Text (20)
Modulation
Null column allowed: No Default value:
NSTATES
Integer
Number of modulation states
Null column allowed: Yes Default value: 16
9.31 MWMultiHops Table For multihop links. Field
Type
Description
Attributes
COMMENT_
Text (255)
Comments
Null column allowed: Yes Default value:
EPO_CLASS
Text (50)
Name of the EPO class
Null column allowed: Yes Default value:
NAME
Text (50)
Name of the multihop link
Null column allowed: No Default value:
9.32 MWMultiHopsLinks Table For microwave links belonging to multihops. Field
Type
Description
Attributes
IDENT
Short
LINK
Text (120)
Name of the link belonging to the multihop
Null column allowed: No Default value:
MULTI_HOP
Text (50)
Name of the multihop link
Null column allowed: No Default value:
OTLINK
Text (120)
Null column allowed: No Default value: 100
Null column allowed: Yes Default value: 50
9.33 MWOperatingModes Table Field
Type
Description
Attributes
FULL_NAME
Text (50)
String describing the mode: displayed in the GUI wherever there is room for long strings (e.g. “Adaptive Coding Modulation”)
Null column allowed: No Default value: “Mode”
265
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MODE_ID
Integer
Number used for managing relationships between related tables
Null column allowed: No Default value:
OPERATION_FLAG
Short
XOR of supported mode (00 = fix, 01 = with ACM)
Null column allowed: Yes Default value: 0
SHORT_NAME
Text (10)
String describing the mode: used for distinguishing active modulations in a link
Null column allowed: No Default value: “Mode”
9.34 MWOTLinks Table Field
Type
Description
Attributes
ACTIVE
Boolean
Flag to filter links
Null column allowed: Default value: True
COMMENT_
Text (255)
Comment
Null column allowed: Yes Default value:
EPO_CLASS
Text (50)
Null column allowed: Yes Default value:
MEDIUM_TYPE
Text (20)
Null column allowed: No Default value:
NAME
Text (120)
Null column allowed: No Default value:
SITE_A
Text (50)
Null column allowed: No Default value:
SITE_B
Text (50)
Null column allowed: No Default value:
9.35 MWPMP Table For microwave links and hubs belonging to a point-to-multipoint group. Field
Type
Description
Attributes
HUB
Text (50)
Name of the hub
Null column allowed: No Default value:
LINK
Text (120)
Name of the link
Null column allowed: No Default value:
9.36 MWPorts Table For microwave ports. Field
266
Type
Description
Attributes
CHANNEL
Short
Channel Number
Null column allowed: No Default value: 0
LINK
Text (120)
Name of the link
Null column allowed: No Default value:
POLARIZATION
Text (1)
Signal polarization of this channel
Null column allowed: No Default value: ‘H’
RX_ATTENUATION
Float
Rx attenuation loss for this channel
Null column allowed: Yes Default value: 1
RX_PORT
Short
Number of the port on the RX equipment where the channel is connected
Null column allowed: Yes Default value: 1
STATUS
Short
Status of the microwave port (0 = main,1 = standby, or 2 = diversity)
Null column allowed: No Default value: 0
TX_ATTENUATION
Float
Tx attenuation loss for this channel
Null column allowed: Yes Default value: 0
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
TX_PORT
Short
Number of the port on the TX equipment where the channel is connected
Null column allowed: Yes Default value: 1
WAY
Short
Way of the link AB or BA
Null column allowed: No Default value: 0
9.37 MWRepeaters Table For microwave repeaters. Field
Type
Description
Attributes
ANTENNA
Text (50)
Repeater antenna
Null column allowed: Yes Default value:
ANTENNA_2
Text (50)
Used if type is Back to Back Antenna (from the antenna table) (point to B)
Null column allowed: Yes Default value:
AZIMUTH_A
Float
Azimuth of the repeater in the direction of A
Null column allowed: Yes Default value: 0
AZIMUTH_B
Float
Azimuth of the repeater in the direction of B
Null column allowed: Yes Default value: 0
DX
Float
X coordinate relative to site position
Null column allowed: Yes Default value: 0
DY
Float
Y coordinate relative to site position
Null column allowed: Yes Default value: 0
FREQ_BAND
Text (50)
Frequency band of the repeater
Null column allowed: No Default value:
GUIDE
Text (50)
Used if type is Back to Back Antenna (from the guide table)
Null column allowed: Yes Default value:
HEIGHT
Float
Height of the repeater
Null column allowed: Yes Default value: 30
HEIGHT_2
Float
Height (pointed to B)
Null column allowed: Yes Default value: 30
LG_GUIDE
Float
Guide length
Null column allowed: Yes Default value: 0
NAME
Text (50)
Name of the repeater
Null column allowed: No Default value:
REPEATER_TYPE
Short
Type of the repeater (Reflector or Back-to-back antennas)
Null column allowed: Yes Default value: 0 (Reflector)
REVERSE_POLAR
Boolean
If true, tx polarization from P to B is not the same as from A to P (and resp, B->P is different to P->A)
Null column allowed: No Default value: False
SITE
Text (50)
Name of the repeater’s site
Null column allowed: No Default value:
SURFACE
Float
Repeater surface area (sq. m)
Null column allowed: Yes Default value: 5
TILT_A
Float
Tilt of the repeater antenna in the direction of A
Null column allowed: Yes Default value:
TILT_B
Float
Tilt of the repeater antenna in the direction of B
Null column allowed: Yes Default value:
9.38 MWSubbands Table For microwave frequency subbands. Field
Type
Description
Attributes
EXCLUDE_L
Text (250)
Excluded channels in the lower half-band
Null column allowed: Yes Default value:
267
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
EXCLUDE_U
Text (250)
Excluded channels in the upper half-band
Null column allowed: Yes Default value:
F0
Double
Central frequency
Null column allowed: Yes Default value: 4700
FREQ_BAND
Text (50)
Frequency band
Null column allowed: Yes Default value:
KL
Double
Lower half-band shift
Null column allowed: Yes Default value: -310
KU
Double
Upper half-band shift
Null column allowed: Yes Default value: 2
N_MAX
Integer
Last channel number
Null column allowed: Yes Default value: 10
N_MIN
Integer
First channel number
Null column allowed: Yes Default value: 1
NAME
Text (50)
Name of the sub-band
Null column allowed: No Default value:
PREFIX_L
Text (5)
Prefix for formatting channel in lower sub-band
Null column allowed: Yes Default value:
PREFIX_U
Text (5)
Prefix for formatting channel in upper sub-band
Null column allowed: Yes Default value:
REC_UIT
Text (255)
ITU Recommendations
Null column allowed: Yes Default value:
STEP
Integer
Step size between first and last channel number
Null column allowed: Yes Default value: 1
SUFFIX_L
Text (5)
Suffix for formatting channel in lower sub-band
Null column allowed: Yes Default value:
SUFFIX_U
Text (5)
Suffix for formatting channel in upper sub-band
Null column allowed: Yes Default value:
XS
Double
Inter-channel space
Null column allowed: Yes Default value: 28
9.39 MWTplLinks Table For microwave link templates. Field
Type
Description
Attributes
ACTIVE_MODULATIONS_A
Text (255)
List of modulations among family ones available for that link (null = All)
Null column allowed: Yes Default value:
ACTIVE_MODULATIONS_B
Text (255)
List of modulations among family ones available for that link (null = All)
Null column allowed: Yes Default value:
ANTENNA_A
Text (50)
Main antenna at site A
Null column allowed: Yes Default value:
ANTENNA_B
Text (50)
Main antenna at site B
Null column allowed: Yes Default value:
ANTENNA2_A
Text (50) Diversity antenna on site A (antenna used for B >> A, when A is receiver)
Null column allowed: Yes Default value:
ANTENNA2_B
Text (50) Diversity antenna on site B (antenna used for A >> B, when B is receiver)
Null column allowed: Yes Default value:
268
ATMOS_PRESSURE
Float
Atmospheric pressure in mbar
Null column allowed: Yes Default value:
BER
Double
Bit Error Rate
Null column allowed: Yes Default value: 1e-3
BER2
Double
Second Bit Error Ratio (i.e. 1e-6)
Null column allowed: Yes Default value: 1e-6
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
Field
Type
Description
Attributes
BRANCHING_CONFIG_A
Text (50)
Branching configuration at A
Null column allowed: Yes Default value:
BRANCHING_CONFIG_B
Text (50)
Branching configuration at B
Null column allowed: Yes Default value:
C_FACTOR
Float
Vigants-Barnett method: C factor
Null column allowed: Yes Default value: 1
CLIMATE_ZONE
Short
Rain Climate Zone
Null column allowed: Yes Default value: 4
ENVTYPE
Integer
Type of environment
Null column allowed: Yes Default value: 0
EPO_CLASS
Text (50)
EPO Class for the link
Null column allowed: Yes Default value:
EQUIPMENT_A
Text (50)
Equipment at site A
Null column allowed: Yes Default value:
EQUIPMENT_B
Text (50)
Equipment at site B
Null column allowed: Yes Default value:
FREQ_BAND
Text (50)
Frequency band of the link
Null column allowed: No Default value:
FREQ_SUBBAND
Text (50)
Type of channelisation within the selected frequency band for A >> B
Null column allowed: Yes Default value:
FREQ_SUBBAND_B
Text (50)
Type of channelisation within the selected frequency band for B >> A
Null column allowed: Yes Default value:
GEOCLIM_FACTOR
Double
Geoclimatic factor used for Rec ITU-530
Null column allowed: Yes Default value:
GUIDE_LG1
Float
Length of GUIDE1
Null column allowed: Yes Default value: 0
GUIDE_LG2
Float
Length of GUIDE2
Null column allowed: Yes Default value: 0
GUIDE_LG3
Float
Length of GUIDE3
Null column allowed: Yes Default value: 0
GUIDE_LG4
Float
Length of GUIDE4
Null column allowed: Yes Default value: 0
GUIDE_USE1
Integer
Use of Guide 1 on site A
Null column allowed: Yes Default value: 0
GUIDE_USE2
Integer
Use of Guide 2 on site B
Null column allowed: Yes Default value: 1
GUIDE_USE3
Integer
Use of Guide 1 on site B
Null column allowed: Yes Default value: 0
GUIDE_USE4
Integer
Use of Guide 2 on site A
Null column allowed: Yes Default value: 1
GUIDE1
Text (50)
Waveguide when A transmitting
Null column allowed: Yes Default value:
GUIDE2
Text (50)
Waveguide when B receiving
Null column allowed: Yes Default value:
GUIDE3
Text (50)
Waveguide when B transmitting
Null column allowed: Yes Default value:
GUIDE4
Text (50)
Waveguide when A receiving
Null column allowed: Yes Default value:
HEIGHT_A
Float
Height at site A
Null column allowed: Yes Default value: 0
HEIGHT_B
Float
Height at site B
Null column allowed: Yes Default value: 0
KQ_FACTOR
Float
KQ reliability method: KQ Factor
Null column allowed: Yes Default value:
269
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
Field
Type
Description
Attributes
MTTR
Float
Minimum Time To Repair
Null column allowed: Yes Default value: 0
NAME
Text (120)
Name of the microwave link template
Null column allowed: No Default value:
PL
Float
POLARIZATION_A
Text (1)
Polarisation of the descending link 'siteA - site B' (the site A and site B are respectively transmitter and receiver)
Null column allowed: Yes Default value: ‘V’
POLARIZATION_B
Text (1)
Polarisation of the ascending link 'siteA-site B' (the site A and site B are respectively receiver and transmitter)
Null column allowed: Yes Default value: ‘V’
POWER_FLAG_A
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
POWER_FLAG_B
Short
Type of power: Null column allowed: Yes 0 = Relative to Max; 1 = Relative to Std; 2 = Relative to Low; 3 = Absolute Default value: 0
PROPAG_IMODEL
Text (50)
Propagation model used for interference calculation
Null column allowed: Yes Default value:
PROPAG_MODEL
Text (50)
Propagation model
Null column allowed: Yes Default value:
R001
Float
Rain intensity exceeded for 0.01% of time (mm/hr)
Null column allowed: Yes Default value:
RAIN_HEIGHT
Float
RAIN_ZONE
Short
REFRACTIVITY
Float
REFRACTIVITY_KE
Float
N-units /km
Null column allowed: Yes Default value:
RXLOSS_ATT_A
Float
Reception losses due to attenuators at A
Null column allowed: Yes Default value: 0
RXLOSS_ATT_B
Float
Reception losses due to attenuators at B
Null column allowed: Yes Default value: 0
SEPARATION_A
Float
Distance between antenna and diversity antenna (siteA receiver)
Null column allowed: Yes Default value: 0
SEPARATION_B
Float
Distance between antenna and diversity antenna (siteB receiver)
Null column allowed: Yes Default value: 0
TEMPERATURE
Float
Temperature
Null column allowed: Yes Default value:
TERRAIN_TYPE
Integer
Terrain type (Vigants)
Null column allowed: Yes Default value: 0
TX_POWER_A
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Yes Default value: 0
TX_POWER_B
Float
Absolute tuned power, not relative to equipment maximum power
Null column allowed: Yes Default value: 0
TXLOSS_ATT_A
Float
Transmission losses due to attenuators at A
Null column allowed: Yes Default value: 0
TXLOSS_ATT_B
Float
Transmission losses due to attenuators at B
Null column allowed: Yes Default value: 0
TXLOSS_BRANCHING_A
Float
Transmission losses due to connectors and branching at A
Null column allowed: Yes Default value: 0
TXLOSS_BRANCHING_B
Float
Transmission losses due to connectors and branching at B
Null column allowed: Yes Default value: 0
VAPOR
Float
Vapour density (g/cu. m)
Null column allowed: Yes Default value:
270
Null column allowed: Yes Default value: 10
Null column allowed: Yes Default value: Rain zone
Null column allowed: Yes Default value: 4 Null column allowed: Yes Default value:
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
AT321_DSR_E1
9.40 Networks Table For network-level parameters. Field
Type
Description
Attributes
DEFAULT_MODEL
Text (50)
Default propagation model
Null column allowed: Yes Default value: ‘Cost-Hata’
DEFAULT_RESOLUTION
Float
Default calculation resolution
Null column allowed: Yes Default value: 50
DMAX
Float
Maximum radius for a cell
Null column allowed: Yes Default value: -1
NAME
Text (50)
SHARED_RESULTS_FOLDER
Text (255)
Shared results storage folder
Null column allowed: Yes Default value:
SYSTEM_
Text (50)
Name of the system
Null column allowed: No Default value: ‘MW’
TECHNOLOGY
Text (10)
Name of the technology
Null column allowed: No Default value: ‘FWA’
Null column allowed: No Default value:
9.41 PropagationModels Table For propagation models. Field
Type
Description
Attributes
Data
Binary
Model specific parameters
Null column allowed: Yes Default value:
Description
Text (255)
User defined
Null column allowed: Yes Default value:
Name
Text (50)
Name of the propagation model
Null column allowed: No Default value:
Signature
Text (40)
Unique Global ID of last model update
Null column allowed: No Default value:
Type
Text (50)
ProgID of the model
Null column allowed: No Default value:
9.42 Sites Table For sites. Field
Type
Description
Attributes
ALTITUDE
Float
Real altitude Unit: m
Null column allowed: Yes Default value: 0
COMMENT_
Text (255)
Additional information on the site
Null column allowed: Yes Default value: 0
LATITUDE
Double
Y coordinate
Null column allowed: No Default value: 0
LONGITUDE
Double
X coordinate
Null column allowed: No Default value: 0
NAME
Text (50)
Site name
Null column allowed: No Default value:
PYLON_HEIGHT
Float
Height of the pylon at site
Null column allowed: Yes Default value: 50
SUPPORT_INFO
Text (50)
Type of support (pylon, tower, etc.) used at the site
Null column allowed: Yes Default value:
271
Atoll 3.2.1 Data Structure Reference Guide Chapter 9: Microwave Links Data Structure
© Forsk 2014
9.43 SitesLists Table For sites belonging to site lists. Field
Type
Description
Attributes
LIST_NAME
Text (50)
First part of the unique key. Name of the list
Null column allowed: No Default value:
SITE_NAME
Text (50)
Second part of the unique key. Name of the site
Null column allowed: No Default value:
9.44 SitesListsNames Table For names of site lists. Field
Type
Description
Attributes
NAME
Text (50)
Name of the list
Null column allowed: No Default value:
9.45 Units Table For the reception and transmission units, the projection coordinate system specified in the ATL document, and the database internal coordinate system. Field
Type
Description
Attributes
COORD_SYSTEM
Integer
Display coordinate system when creating database
Null column allowed: Yes Default value: -1
GAIN_UNIT
Integer
Unit used for gains (dBd or dBi) Choice list: 0=dBd; 1=dBi;
Null column allowed: Yes Default value: 0
PROJECTION
Integer
Projected coordinate system for geo data
Null column allowed: Yes Default value: -1
RECEPTION_UNIT
Integer
Reception unit when creating database Choice list: 0=dBm; 1=dbµV; 2=dbµV/m;
Null column allowed: No Default value: 0
TRANSMISSION_UNIT
Integer
Transmission unit when creating database Choice list: 0=dBm; 1=Watts; 2=kWatts;
Null column allowed: No Default value: 0
272
Atoll 3.2.1 Data Structure Reference Guide Chapter 10: Radio Data Formats
AT321_DSR_E1
10 Radio Data Formats Radio network data in Atoll contains the following information, depending on the technology used in the network: • • • •
• • • • • • • •
Site: The geographic location of transmitters (sectors, installed antennas, other equipment). A site can have one or more transmitters. Antenna: The radiation patterns and gains for antennas installed at transmitters. Transmitter: A group of radio devices installed at a site with there transmission/reception characteristics (antennas, feeders, TMAs, other equipment). A transmitter can have one or more cells or subcells. Cell: An RF carrier available at a transmitter in UMTS, CDMA2000, TD-SCDMA, LTE, WiMAX, and Wi-Fi networks. A cell is fully defined by the "transmitter-carrier" pair. Each cell in these networks is independent, i.e., has its own identifier, power levels, performance characteristics. TRX: An RF carrier available at a transmitter in GSM networks. A transceiver (TRX) can carry one ARFCN which can correspond to the BCCH (7 traffic timeslots) or TCH (8 traffic timeslots). Subcell: A subcell is a group of TRXs with the same radio characteristics. A subcell is fully defined by the "transmitterTRX type" pair. Base station: This is the generic name for a cell site ("site-transmitter-cell" or "site-transmitter-subcells"). Technologyspecific names can be BTS, Node-B, eNode-B, etc. RF repeater: An RF repeater receives, amplifies, and retransmits RF carriers both in downlink and uplink. The repeater receives signals from a donor transmitter which it retransmits using a coverage-side antenna with amplification. Remote antenna: Transmitter antennas located at a remote location with respect to the transmitter’s site. Microwave link: A point-to-point link using microwave frequencies used for backhaul in radio access networks or for fixed wireless access. PMP microwave link: A group of microwave links originating from a common node to serve more than one location. Passive microwave repeater: A passive microwave repeater receives and retransmits microwave signals without amplification. Passive repeaters do not have power sources of their own. Active repeaters, on the other hand, amplify the received signal. Reflectors are examples of passive repeaters.
10.1 XML Import/Export Format All the data tables in an Atoll document can be exported to XML files. Atoll creates the following files when data tables are exported to XML files: • •
An index.xml file which contains the mapping between the data tables in Atoll and the XML file created for each table. One XML file per data table which contains the data table format (schema) and the data.
When XML files are imported to a document, the table and field definitions are not modified, i.e., the Networks and CustomFields tables are exported to XML file but are not imported. The following sections describe the structures of the XML files created at export.
10.1.1 Index.xml File Format The index.xml file stores the system (GSM, UMTS, etc.) and the technology (TDMA, CDMA, etc.) of the document, and the version of Atoll used for exporting the data tables to XML files. It also contains the mapping between the data tables in the Atoll document and the XML file corresponding to each data table. The root tag
of the index.xml file contains the following attributes: Attribute
Description
Atoll_File_System
Corresponds to the SYSTEM_ field of the Networks table of the exported document
Atoll_File_Technology
Corresponds to the TECHNOLOGY field of the Networks table of the exported document
Atoll_File_Version
Corresponds to the Atoll version
The index file also contains the mapping between the tables exported from Atoll and the XML files corresponding to each table. This list is sorted in the order in which tables must be imported in Atoll. The list is composed of tags with the following attributes: Attribute
Description
XML_File
Corresponds to the exported XML file name (e.g., "Sites.xml")
Atoll_Table
Corresponds to the exported Atoll table name (e.g., "Sites")
A sample extract of the index.xml is given below:
273
Atoll 3.2.1 Data Structure Reference Guide Chapter 10: Radio Data Formats
© Forsk 2014
... Note that no closing tag is required.
10.1.2 XML File Format Atoll creates an XML file per exported data table. This XML file has two sections, one for storing the description of the table structure, and the second for the data itself. The XML file uses the standard XML rowset schema (schema included in the XML file between and tags). Rowset Schema The XML root tag for XML files using the rowset schema is the following: The schema definition follows the root tag and is enclosed between the following tags: and tags -> In the rowset schema, after the schema description, the data are enclosed between and . Between these tags, each record is handled by a tag having its attributes set to the record field values since in the rowset schema, values are handled by attributes. Note that no closing tag is required. A sample extract of a Sites.xml file containing the Sites table with only one site is given below:
274
Atoll 3.2.1 Data Structure Reference Guide Chapter 10: Radio Data Formats
AT321_DSR_E1
10.2 RF 2D Antenna Pattern Format This section describes the format of the DIAGRAM field of the Antennas table. This field stores the antenna diagrams in a 2D (angle vs. attenuation) format. This is the format of the contents of the DIAGRAM field of the Antennas table when it is copied from, pasted to, imported to (from TXT or CSV files), and exported from (from TXT, CSV, or XLS files) the Antennas table. Antenna patterns can also be imported in Planet 2D-format antenna files and 3D antenna files. The file format required for 3D antenna file import is described in "Import Format of 3D Antenna Pattern Text Files" on page 277. The format of 2D antenna patterns containing co-polar diagrams only can be understood from Figure 10.1 on page 275. Pattern Discriptor 1
Co-polar Horizontal Diagram
Pattern Discriptor 2
Co-polar Vertical Diagram
End
2 0 0 360 0 0 1 0 2 0.1 … 1 0 360 0 0 1 0.1 … 0 Figure 10.1: 2D RF Antenna Pattern Format Containing Co-polar Diagrams Only The contents of the DIAGRAM field are formatted as follows: •
Pattern Descriptor 1: Space-separated list of parameters. • First entry: The number of co-polar diagrams. For example, 2. • Second entry: First co-polar diagram type = 0 for azimuth (horizontal) diagram. • Third entry: The elevation angle of the azimuth diagram. • Fourth entry: The number of angle-attenuation pairs in the first co-polar diagram. For example, 360.
•
Co-polar Horizontal Diagram: Horizontal co-polar diagram (the second entry in the preceding descriptor is 0). The format is space-separated angle attenuation pairs. For example, 0 0 1 0 2 0.1....
•
Pattern Descriptor 2: Space-separated list of parameters. • First entry: Second co-polar diagram type = 1 for elevation (vertical) diagram. • Second entry: The azimuth angle of the elevation diagram. • Third entry: The number of angle-attenuation pairs in the second co-polar diagram. For example, 360.
•
Co-polar Vertical Diagram: Vertical co-polar diagram (the first entry in the preceding descriptor is 1). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.1....
•
End: The number cross-polar diagrams = 0.
The format of 2D antenna patterns containing co-polar and cross-polar diagrams can be understood from Figure 10.2 on page 276.
275
Atoll 3.2.1 Data Structure Reference Guide Chapter 10: Radio Data Formats
Pattern Discriptor 1
© Forsk 2014
Co-polar Horizontal Diagram
Pattern Discriptor 3
Pattern Discriptor 2
Cross-polar Horizontal Diagram
Pattern Discriptor 4
Co-polar Vertical Diagram
Cross-polar Vertical Diagram
2 0 0 360 0 0 1 0 2 0.1 … 1 0 360 0 0 1 0.1 … 2 0 0 360 0 0 1 0 2 0.1 … 1 0 360 0 0 1 0.1 … Figure 10.2: 2D RF Antenna Pattern Format Containing Co-polar and Cross-polar Diagrams The contents of the DIAGRAM field are formatted as follows: •
Pattern Descriptor 1: Space-separated list of parameters. • First entry: The number of co-polar diagrams. For example, 2. • Second entry: First co-polar diagram type = 0 for azimuth (horizontal) diagram. • Third entry: The elevation angle of the azimuth diagram. • Fourth entry: The number of angle-attenuation pairs in the first co-polar diagram. For example, 360.
•
Co-polar Horizontal Diagram: Horizontal co-polar diagram (the second entry in the preceding descriptor is 0). The format is space-separated angle attenuation pairs. For example, 0 0 1 0 2 0.1....
•
Pattern Descriptor 2: Space-separated list of parameters. • First entry: Second co-polar diagram type = 1 for elevation (vertical) diagram. • Second entry: The azimuth angle of the elevation diagram. • Third entry: The number of angle-attenuation pairs in the second co-polar diagram. For example, 360.
•
Co-polar Vertical Diagram: Vertical co-polar diagram (the first entry in the preceding descriptor is 1). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.1....
•
Pattern Descriptor 3: Space-separated list of parameters. • First entry: The number of cross-polar diagrams. For example, 2. • Second entry: First cross-polar diagram type = 0 for azimuth (horizontal) diagram. • Third entry: The elevation angle of the azimuth diagram. • Fourth entry: The number of angle-attenuation pairs in the first cross-polar diagram. For example, 360.
•
Cross-polar Horizontal Diagram: Horizontal cross-polar diagram (the second entry in the preceding descriptor is 0). The format is space-separated angle attenuation pairs. For example, 0 0 1 0 2 0.1....
•
Pattern Descriptor 4: Space-separated list of parameters. • First entry: Second cross-polar diagram type = 1 for elevation (vertical) diagram. • Second entry: The azimuth angle of the elevation diagram. • Third entry: The number of angle-attenuation pairs in the second cross-polar diagram. For example, 360.
•
Cross-polar Vertical Diagram: Vertical cross-polar diagram (the first entry in the preceding descriptor is 1). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.1....
You can use a 3rd party software or develop a tool to convert the contents of the DIAGRAM field into binary. In binary, each antenna is described by a header and a list of value pairs. The header is defined as follows: • • • • • • •
flag: (Integer, 32 bits) -1 for omni diagrams, 0 for directional num: (Short integer, 16 bits) Number of diagrams (0, 1, 2, 3, 4) siz0: (Short integer, 16 bits) Size of the first diagram (horizontal co-polar section, elevation = 0°) siz1: (Short integer, 16 bits) Size of the second diagram (vertical co-polar section, azimuth = 0°) siz2: (Short integer, 16 bits) Size of the third diagram (horizontal cross-polar) siz3: (Short integer, 16 bits) Size of the fourth diagram (vertical cross-polar) prec: (Short integer, 16 bits) Precision of the following angle values (100)
Then follows the content of each of the defined diagrams, i.e., the diagrams whose sizes (siz0, siz1, siz2, siz3) are not zero. Each diagram consists of a list of value pairs. The number of value pairs in a list depends on the value of the siz0, siz1, siz2, and siz3 parameters. For example, siz2 = 5 means there are five value pairs in the third diagram. The value pairs in each list are: • •
ang: (Short integer, 16 bits) The first component of the value pair is the angle in degrees multiplied by 100. For example, 577 means 5.77 degrees. loss: (Short integer, 16 bits) The second component of the value pair is the loss in dB for the given angle ang.
All the lists of value pairs are concatenated without a separator.
276
Atoll 3.2.1 Data Structure Reference Guide Chapter 10: Radio Data Formats
AT321_DSR_E1
10.3 Import Format of 3D Antenna Pattern Text Files Text files containing 3D antenna patterns that can be imported in Atoll must have the following format: • •
Header: The text file can contain a header with additional information. When you import the antenna pattern you can indicate the row number in the file where the header ends and the antenna pattern begins. Antenna Pattern: Each row contains three values to describe the 3D antenna pattern. The columns containing the values can be in any order: • Azimuth: Allowed range of values is from 0° to 360°. The smallest increment allowed is 1°. • Tilt: Allowed range of values is from -90° to 90° or from 0° to 180°. The smallest increment allowed is 1°. • Attenuation: The attenuation in dB.
10.4 Microwave 2D Antenna Pattern Format This section describes the format of the PATTERN field of the MW Antennas table. This field stores the antenna diagrams in a 2D (angle vs. attenuation) format. This is the format of the contents of the PATTERN field of the MW Antennas table when it is copied from, pasted to, imported to (from TXT or CSV files), and exported from (from TXT, CSV, or XLS files) the MW Antennas table. Antenna patterns can also be imported in Planet 2D-format antenna files and 3D antenna files. The file format required for 3D antenna file import is described in "Import Format of 3D Antenna Pattern Text Files" on page 277. The format of 2D antenna patterns can be understood from Figure 10.3 on page 277. Pattern Discriptor 1
Co-polar H-V Diagram
Pattern Discriptor 2
Co-polar H-H Diagram
Pattern Discriptor 3
Cross-polar H-V Diagram
Pattern Discriptor 4
Cross-polar H-H Diagram
Pattern Discriptor 5
Co-polar V-V Diagram
Pattern Discriptor 6
Co-polar V-H Diagram
Pattern Discriptor 7
Cross-polar V-V Diagram
Pattern Discriptor 8
Cross-polar V-H Diagram
4 0 1 0 360 0 0 1 0.5 ... 0 0 0 360 0 0 1 0.5 ... 1 1 0 360 0 0 1 0.5 ... 1 0 0 360 0 0 1 0.5 ... 4 0 1 0 360 0 0 1 0.5 ... 0 0 0 360 0 0 1 0.5 ... 1 1 0 360 0 0 1 0.5 ... 1 0 0 360 0 0 1 0.5 ... Figure 10.3: 2D Microwave Antenna Pattern Format The contents of the PATTERN field are formatted as follows: •
Pattern Descriptor 1: Space-separated list of parameters. • First entry: The number of H_polarisation diagrams. For example, 4. • Second and third entries: First diagram type = 0 1, for co-polar H-V diagram ("EL HH" in Atoll). • Fourth entry: The elevation angle of the azimuth diagram. • Fifth entry: The number of angle-attenuation pairs in the first co-polar diagram. For example, 360.
•
Co-polar H-V Diagram: Co-polar H-V diagram (the second and third entries in the preceding descriptor are 0 1). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
•
Pattern Descriptor 2: Space-separated list of parameters. • First and second entries: Second diagram type = 0 0, for co-polar H-H diagram ("HH" in Atoll). • Third entry: The azimuth angle of the elevation diagram.
277
Atoll 3.2.1 Data Structure Reference Guide Chapter 10: Radio Data Formats
•
278
© Forsk 2014
Fourth entry: The number of angle-attenuation pairs in the second co-polar diagram. For example, 360.
•
Co-polar H-H Diagram: Co-polar H-H diagram (the first and second entries in the preceding descriptor are 0 0). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
•
Pattern Descriptor 3: Space-separated list of parameters. • First and second entries: Third diagram type = 1 1, for cross-polar H-V diagram ("EL VH" in Atoll). • Third entry: The elevation angle of the azimuth diagram. • Fourth entry: The number of angle-attenuation pairs in the third co-polar diagram. For example, 360.
•
Cross-polar H-V Diagram: Cross-polar H-V diagram (the second and third entries in the preceding descriptor are 0 1). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
•
Pattern Descriptor 4: Space-separated list of parameters. • First and second entries: Fourth diagram type = 1 0, for cross-polar H-H diagram ("VH" in Atoll). • Third entry: The azimuth angle of the elevation diagram. • Fourth entry: The number of angle-attenuation pairs in the fourth co-polar diagram. For example, 360.
•
Cross-polar H-H Diagram: Cross-polar H-H diagram (the first and second entries in the preceding descriptor are 0 0). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
•
Pattern Descriptor 5: Space-separated list of parameters. • First entry: The number of V_polarisation cross-polar diagrams. For example, 4. • Second and third entries: First diagram type = 0 1, for co-polar V-V diagram ("EL VV" in Atoll). • Fourth entry: The elevation angle of the azimuth diagram. • Fifth entry: The number of angle-attenuation pairs in the first cross-polar diagram. For example, 360.
•
Co-polar V-V Diagram: Co-polar V-V diagram (the first and second entries in the preceding descriptor are 1 1). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
•
Pattern Descriptor 6: Space-separated list of parameters. • First and second entries: Second diagram type = 0 0, for co-polar V-H diagram ("VV" in Atoll). • Third entry: The azimuth angle of the elevation diagram. • Fourth entry: The number of angle-attenuation pairs in the second cross-polar diagram. For example, 360.
•
Co-polar V-H Diagram: Co-polar V-H diagram (the first and second entries in the preceding descriptor are 1 0). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
•
Pattern Descriptor 7: Space-separated list of parameters. • First and second entries: Third diagram type = 1 1, for cross-polar V-V diagram ("EL HV" in Atoll). • Third entry: The elevation angle of the azimuth diagram. • Fourth entry: The number of angle-attenuation pairs in the third cross-polar diagram. For example, 360.
•
Cross-polar V-V Diagram: Cross-polar V-V diagram (the first and second entries in the preceding descriptor are 1 1). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
•
Pattern Descriptor 8: Space-separated list of parameters. • First and second entries: Fourth diagram type = 1 0, for cross-polar V-H diagram ("HV" in Atoll). • Third entry: The azimuth angle of the elevation diagram. • Fourth entry: The number of angle-attenuation pairs in the fourth cross-polar diagram. For example, 360.
•
Cross-polar V-H Diagram: Cross-polar V-H diagram (the first and second entries in the preceding descriptor are 1 0). The format is space-separated angle attenuation pairs. For example, 0 0 1 0.5....
Atoll 3.2.1 Data Structure Reference Guide AT321_DSR_E1
279
• Head Office 7 rue des Briquetiers 31700 Blagnac, France Tel: +33 562 747 210 Fax: +33 562 747 211
AT321_DSR_E1
• US Office
• China Office
200 South Wacker Drive – Suite 3100 Chicago, IL 60606, USA Tel: +1 312 674 4800 Fax: +1 312 674 4847
Suite 302, 3/F, West Tower, Jiadu Commercial Building, No. 66 Jianzhong Road, Tianhe Hi-Tech Industrial Zone, Guangzhou, 510665, P. R. of China Tel: +86 20 8553 8938 Fax: +86 20 8553 8285
www.forsk.com
February 2014