ASTM D2911-10

Designation: D2911 − 10

Standard Specification for

Dimensions and Tolerances for Plastic Bottles 1 This standard is issued under the fixed designation D2911; the number immediately following the designation indicates the year of original origin al adoption or, in the case of revis revision, ion, the year of last revision. revision. A number in paren parenthese thesess indicates the year of last reappr reapproval. oval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.

3.1.3 bottle thickn t he sm small aller er di dime mens nsio ion n in a pl plan anee thickness— ess— the parallel to the bottle base.

1. Sco Scope pe 1.1 This specification specification covers the thread configuration configuration and dimens dim ension ionss for fini finishe shess for pla plastic stic bot bottles tles with scr screwew-typ typee closures, having a maximum capacity of 18.9 L (5 gal) and a maximum bottle dimension of 305 mm (12 in.). Included are tolerances for bottle capacity and body dimensions.

3.1.4 bottle width— the the larger dimension in a plane parallel to the bottle base. 4. Dimensions and Recommended Variations Variations 4.1 Recom In Recommen mended ded Varia ariation tionss in Ove Overflo rflow w Cap Capacit acity— y— In overflow capacity recommended variations of plastic bottles up to 18.9 L (5 gal) in size shall be in accordance with Table 1. 1.

1.2 The values values stated in SI uni units ts are to be reg regard arded ed as the standard. 1.3 The following following precautionary precautionary caveat caveat pertains only to the test met method hodss por portio tion, n, Sect Section ion 8 of thi thiss spe specific cificatio ation. n. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this sta standa ndard rd to esta establi blish sh app appro ropri priate ate saf safety ety and hea health lth practices and determine the applicability of regulatory limitations prior to use.

4.2 Recomm The Recommend ended ed Vari ariati ations ons in Bod Bodyy Dim Dimens ension ions— s— The recommend recomm ended ed var variati iations ons in the bod body y dim dimens ension ionss of pla plastic stic bottles covered by this specification shall be in accordance with Table 2. 2. Dimensions and Design— The 4.3 Finish Dimensions The bottle finish dimensions mensio ns and design design for the nin ninee fini finishe shess cov covere ered d by thi thiss specification shall be in accordance with Figs. with Figs. 1-8 a and nd Tables Tables 3-10.. 3-10

NOTE 1—There is no known ISO equivalent to this standard.

2. Referenc Referenced ed Documents Documents

5. Sampl Sampling ing

2

2.1 ASTM Standards: D618 Practice D618 Practice for Conditioning Plastics for Testing D1898 Practice D1898 Practice for Sampling of Plastics (Withdrawn Plastics (Withdrawn 1998) 3

5.1 A batch batch or lot shall be considered considered as a unit of manufacture. 5.2 Unl Unless ess oth otherw erwise ise agr agreed eed upo upon n betw between een man manufa ufactu cturer rer and pur purcha chaser ser,, the mate materia riall sha shall ll be sam sample pled d in acco accorda rdance nce with the procedure described in Section 9 of Practice D1898 D1898.. Adequa Ade quate te stat statisti istical cal sam sampli pling ng pri prior or to pac packag kaging ing sha shall ll be considered consid ered an accepta acceptable ble alterna alternative. tive.

3. Terminology 3.1 Definitions: 3.1.1 bottle finish— the the configuration configuration of the neck or opening of th thee bo bottl ttlee wh which ich se serv rves es to en enga gage ge sp speci ecific fic pa part rtss of th thee closure in order to securely attach it to the bottle.

6. Condi Condition tioning ing 6.1 Conditioning— Conditi Condition on the test spe specim cimens ens at 23 6 2°C (73.4 6 3.6°F) and 50 6 5% relative humidity for not less than th an 40 h pr prio iorr to tes testt in ac acco cord rdan ance ce wi with th Pr Proc oced edur uree A of Practice D618 Practice D618 for for those tests where conditioning is required. In cases of disagr disagreement, eement, the tolera tolerances nces shall be 6 1°C (61.8°F) and 62 % relative humidity.

3.1.2 bottle height— the the maximum dimension of a bottle in a pla plane ne per perpen pendic dicula ularr to the bottle bottle bas basee whe when n the bottle is setting in its normal upright position.

1 This specification specification is under the jurisd jurisdiction iction of ASTM Committee Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.19 Subcommittee D20.19 on on Film, Sheeting, and Molded Products. Current edition approved July 1, 2010. Published September 2010. Originally approved in 1970. Last previous edition approved in 2005 as D2911 - 94 (2005). DOI: 10.1520/D2911-10. 2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [email protected]. For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website. 3 The last app approve roved d vers version ion of this historica historicall sta standa ndard rd is refe referenc renced ed on www.astm.org.

6.2 Test Conditions— Conduct Conduct tests in the standard laboratory atmosphere of 23 6 2°C (73.4 6 3.6°F) and 50 6 5 % relative humidity, unless otherwise specified in the test methodss or in th od this is sp speci ecific ficati ation on.. In cas cases es of di disa sagr greem eemen ent, t, th thee tolerances shall be 61°C (61.8°F) and 62 % relative humidity. 7. Appar Apparatus atus 7.1 For Determining Bottle Capacity:

Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States

Copyright by ASTM Int'l (all rights reserved);

1

D2911 − 10 TABLE 1 Bottle Overflow Capacity Tolerances for Plastic Bottles Fluid Ounces Bottle Overflow Capacity l e s s th a n a n d l e s s th a n an d l es s t ha n an d l es s t ha n an d l es s t ha n an d l es s t ha n an d l es s t ha n an d l es s t ha n an d l es s t ha n an d l es s t ha n an d l e s s t ha n an d l e s s t ha n an d l e s s t ha n an d l e s s t ha n an d l e s s t ha n an d l e s s t ha n an d l e s s t ha n a n d l e s s t ha n a n d l e s s t ha n a n d l e s s t ha n a n d l e s s t ha n to 5 g a l l o n s

0.75 1.2 1.6 2.1 2.8 3.9 5.4 7.4 9.8 13 18 26 37 51 72 98 119 13 9 16 0 18 0 21 0

Millilitres Tolerance (±)

0 .7 5 1. 2 1. 6 2. 1 2. 8 3. 9 5. 4 7. 4 9. 8 13 18 26 37 51 72 98 119 13 9 16 0 18 0 21 0

Bottle Overflow Capacity

0 .0 5 0. 07 0 .0 8 0 .1 0 0 .1 2 0 .1 4 0 .1 7 0 .2 0 0 .2 4 0 .3 0 0. 37 0. 44 0. 51 0. 68 0. 81 1. 01 1 .3 0 1. 50 1. 80 2. 00 2. 20 1 % o f c a p a c i ty

22 35 47 62 83 115 15 9 21 8 289 38 4 53 1 76 7 1 09 2 1 50 5 2 12 5 28 9 2 35 1 2 41 0 3 47 2 3 53 1 3 61 99

l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n a n d l e s s th a n to 18.89 litres

Tolerance (±) 22 35 47 62 83 115 159 218 289 38 4 5 31 7 67 10 9 2 15 05 21 25 28 92 35 12 4 10 3 4 72 3 5 31 3 6 19 9

1 .5 2. 0 2 .5 3 .0 3 .5 4 5 6 7 9 11 13 15 20 24 30 38 44 53 59 65 1 % o f c a p a c i ty

TABLE 2 Body Dimensional Tolerance Range of Specific Dimensions i n. 0 1 2 4 6 8 10 12 15

up up up up up up up up up

to to to to to to to to to

bu t bu t bu t bu t bu t bu t b ut b ut b ut

n ot n ot n ot n ot n ot n ot n ot n ot n ot

Height Dimensions mm

i n c l ud i ng i n c l ud i ng i n c l ud i ng i n c l ud i ng i n c l ud i ng i n c l ud i ng including including including

1 2 4 6 8 10 12 15 18

0 2 5 .4 0 5 0 .8 0 1 0 1. 60 1 5 2. 40 2 0 3 .2 0 2 5 4 .0 0 3 0 4 .8 0 3 8 1 .0 0

to to to to to to to to to

2 5 .4 0 5 0. 80 1 0 1 .6 0 15 2. 40 20 3. 20 25 4. 00 3 0 4 .8 0 3 8 1 .0 0 4 5 7 .2 0

7.1.1 Balance, having an accuracy of 60.1 % or better at rated capacity (full scale). 7.1.2 Pipet, Graduated Cylinder , and Beaker , as required. 7.1. 7. 1.3 3 Co Cond nditi ition oned ed wa water ter at 23 6 2.0°C 2.0°C (73 (73.4 .46 3.6°F) containing a wetting agent sufficient to flatten the meniscus and eliminate air bubbles.

i n.

mm

i n.

mm

0 .0 3 0 0. 03 0 0. 05 0 0 .0 5 0 0 .0 6 0 0 .0 6 0 0. 08 0 0. 09 0 0.110

0 .7 6 0. 76 1. 27 1 .2 7 1 .5 2 1 .5 2 2. 03 2. 29 2. 79

0 .0 3 0 0. 05 0 0 .0 6 0 0. 08 0 0. 09 0 0.110 0. 12 0 0. 15 0 0. 15 0

0 .7 6 1. 27 1 .5 2 2. 03 2. 29 2 .7 9 3 .0 5 3 .8 1 3 .8 1

top of the finish surface. No more than 2 min shall be allowed for filling the bottle and no additional water shall be added after the bottle is filled to overflow and free of air bubbles. 8.1.3 If the time exceeds 2 min, discard discard the sample and start over. NOTE 3—The capacity of the container is somewhat time-dependent in that the force of the water in the container will cause the container sides to bul bulge ge wit with h tim timee and addition additional al wat water er wil willl be nee needed ded to adj adjust ust to overflow capacity.

NOTE 2—It is acceptable to use any liquid detergent as the wetting agent.

7.1.4 Stop Watch.

8.1.4 Weigh the filled bottle and record record the weight in grams. 8.1.5 Calcula Calculate te the bottle volume volume as follo follows: ws:

7.2 For Determining Finish and Body Dimensions: 7.2.1 Micrometers, Vernier Height Gages, or Vernier Cali pers with an accuracy of 60.025 mm (60.001 in.). Micrometer ometerss or Telesco elescoping ping Gages with an 7.2.2 Internal Micr accuracy of 60.025 mm ( 60.001 in.). 7.2.3 Commercial Scale, good quality calibrated in 1-mm or 1 ⁄ 32 32-in. increments.

B v

where: Bv Bf Be 0.99 0. 997 7

8. Test Methods Methods 8.1 Bottle Capacity: 8.1. 8. 1.1 1 Weig eigh h th thee em empt pty y bo bottl ttlee an and d re reco cord rd th thee we weig ight ht in grams. 8.1.2 Fill the bottle to overflow capacity with conditioned conditioned water containing the wetting agent, adjusting the meniscus by use of a pipet, if necessary, until the meniscus is tangent to the Copyright by ASTM Int'l (all rights reserved);

Width and Depth Dimensions

= = = =

~ mL! 5 ~ B

f

2 B e ! / 0.997

volume of bot volume bottle, tle, mL, weight weig ht of fille filled d bot bottle, tle, g, weight weig ht of emp empty ty bot bottle, tle, g, and weig we ight ht of wa wate terr (g (g/m /mL) L) at 23 6 2.0°C 2.0°C (73.4 6 3.6°F). B v

~ fluid oz! 5 ~ B

f

2 B e ! / 29.50

where: 29.50 = weight of water (g/fluid oz) at 23 6 2.0°C (73.4 6 3.6°F). 2

D2911 − 10

“L” Style

“M” Style

All-Purpose Thread (Plastic or Metal Closures) (Plastic

Modified Buttress Thread (Plastic Closures)

Threads/in. 5 6 8

a i n. mm i n. mm i n. mm

0. 12 0 3 .0 5 0. 09 4 2 .3 9 0. 08 4 2 .1 3

b

c

0 .0 6 0 1 .5 2 0 .0 4 7 1 .1 9 0 .0 4 2 1 .0 7

0. 05 1 1 .3 0 0. 04 0 1 .0 2 0. 03 6 0 .9 1

Threads/in. 5 6 8

a i n. mm i n. mm i n. mm

0 .1 2 0 3 .0 5 0 .0 9 4 2 .3 9 0 .0 8 4 2 .1 3

b

c

0 .0 6 0 1 .5 2 0 .0 4 7 1 .1 9 0 .0 4 2 1 .0 7

0 .0 4 9 1 .2 4 0 .0 3 9 0 .9 9 0 .0 3 5 0 .8 9

Example Thread Nomenclature “L” Style: L28SP4 L28SP400 00 “M” Style: M28SP4 M28SP400 00

NOTE 1— T and and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. NOTE 2—Dimension H is measured from the top of the finish to the point where diameter T , extended parallel to the centerline, intersects the bead or shoulder. NOTE 3—Contour of bead, undercut or shoulder is optional. NOTE 4—Unless otherwise specified, I min applies to the full length of the opening. I min with respect to diameters T and E is not included. I min is specified for filler tube only. NOTE 5—Concentricity of I NOTE 6—A minimum of 1 full turn of thread shall be maintained. NOTE 7—Corresponding dimensions and finish details are shown in Table in Table 3. 3. NOTE 8—Consideration must be given to the sealing surface width for the sealing system being used. NOTE 9—Many child resistant closures, etc. FIG. 1 SP 400 Finish Thread Thread Cross Sections Sections


3

D2911 − 10

Threads/in. 6 8

“L” Style All-Purpose Thread (Plastic or Metal Closures) a b i n . 0 .0 9 4 0. 04 7 m m 2. 39 1. 19 i n . 0 .0 8 4 0. 04 2 m m 2. 13 1. 07

c 0 .0 4 0 1 .0 2 0 .0 3 6 0 .9 1

Threads/in. 6 8

“M” Style Modified Buttress Thread (Plastic Closures) a b i n . 0 .0 9 4 0. 04 7 m m 2 .3 9 1. 19 i n . 0 .0 8 4 0. 04 2 m m 2 .1 3 1. 07

c 0 .0 3 9 0 .9 9 0 .0 3 5 0 .8 9

Example Thread Nomenclature: “L” Style: L22SP4 L22SP410 10 “M” Style: M22SP4 M22SP410 10

NOTE 1—Construction of neck from B to D must be held within the shaded area shown. NOTE 2—A minimum of 1 1 ⁄ 2 turns of thread shall be maintained. NOTE 3—Unless otherwise specified, I min applies to the full length of the opening. I min with respect to diameters T and E is not included. I min is specified for filler tube only. NOTE 4—Concentricity of I NOTE 5— T and and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. NOTE 6—Consideration must be given to the sealing surface width for the sealing system being used. NOTE 7—When valve style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition, it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter. NOTE 8—Corresponding dimensions and details shown in Table in Table 4. 4. FIG. 2 SP 410 Finish Thread Thread Cross Sections Sections

8.1.6 Determi Determine ne the volume in millilitr millilitres es (fluid ounces) for each test specimen. 8.1.7 8.1 .7 Repo Report rt the ari arithm thmetic etic ave averag ragee vol volume ume of the spe specicimens tested as the bottle capacity of the batch or lot from which the samples were chosen.

8.2.1. 8.2 .1.1 1 If the top of the finish finish is par paralle allell to the base of the container and the height must be measured from the top of the finish, and a commercial scale is used, one method is to place the bottle on a flat surface and a straightedge across the top of the bot bottle tle fini finish. sh. The Then n mea measur suree the per perpen pendic dicula ularr dis distan tance ce between the straightedge and the surface upon which the bottle is setting. Make four measurements, each 90° apart, and use the maximum as the bottle height.

8.2 Body Dimensions: 8.2.1 Using a suitabl suitablee microm micrometer eter,, a vernier height gauge, or a scale, measure the height of the bottle. Copyright by ASTM Int'l (all rights reserved);

4

D2911 − 10

“L” Style

“M” Style

All-Purpose Thread (Plastic (Plast ic or Metal Closures)

Modified Buttress Thread (Plastic Closures)

Threads/in.

a

b

c

d

f

6

i n. mm i n. mm i n. mm

0 .0 9 4 2. 39 0 .0 8 4 2. 13 0 .0 4 5 1. 14

0 .0 4 7 1 .1 9 0 .0 4 2 1 .0 7 0 .0 3 0 0 .7 6

0 .0 4 0 1. 02 0 .0 3 6 0. 91 0.011 0. 28

0 .0 2 0 0 .5 1 0 .0 2 0 0 .5 1 0. 0 15 0 .3 8

0 .0 2 0 0 .5 1 0 .0 2 0 0 .5 1 0. 00 5 0 .1 3

8 12

Threads/in. 6 8 12

i n. mm i n. mm i n. mm

a

b

c

d

f

0. 09 4 2. 39 0. 08 4 2. 13 0 .0 5 1 1. 29

0. 04 7 1 .1 9 0. 04 2 1 .0 7 0 .0 3 0 0 .7 6

0. 03 9 0 .9 9 0. 03 5 0 .8 9 0. 01 6 0 .4 1

0 .0 3 0 0 .7 6 0 .0 3 0 0 .7 6 0. 02 0 0 .5 1

0 .0 3 0 0. 76 0 .0 3 0 0. 76 0. 00 8 0. 22

Example Thread Nomenclature: “L” Style: L22SP4 L22SP415 15 “M” Style: M22SP4 M22SP415 15

NOTE 1—Construction of neck from B to D must be held within the shaded area shown. NOTE 2—A minimum of 2 turns of thread shall be maintained. NOTE 3—Unless otherwise specified, I min applies to the full length of the opening. I min with respect to diameters T and E is not included. I min is specified for filler tube only. NOTE 4—Concentricity of I T E OTE N 5— and and dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. NOTE 6—Consideration must be given to the sealing surface width for the sealing system being used. NOTE 7—When valve style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition, it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter. NOTE 8—Corresponding dimensions and finish details are shown in Table in Table 5. 5. FIG. 3 SP 415 Finish Thread Thread Cross Sections Sections

(1) If, because of the shape of the container, there is some ques qu estio tion n ab abou outt wh wher eree th thee me meas asur urem emen ents ts ar aree to be ta take ken, n, agreeme agr eement nt sha shall ll be rea reache ched d bet betwee ween n the pur purcha chaser ser and the seller.

8.2.2 Using a suitable micrometer or vernier caliper, caliper, measure the width and thickness of the bottle. 8.2. 8. 2.2. 2.1 1 In th thee cas casee of a re rect ctan angu gular lar co cont ntain ainer er,, us usee th thee midpoints of the sides as the measuring points. 8.2.2.2 8.2.2 .2 For a cylind cylindrical rical container, container, make one measurement on the parting parting lin linee and another another mea measur suremen ementt 90° from the parting partin g line. Use the averag averagee of these two measur measurements ements as the container width.


Dimensions— sions— Using suitable microm 8.3 Finish Dimen micrometers, eters, vernier calipers, or telescoping gages, measure the finish dimensions of the bottle.

5

D2911 − 10

NOTE 1—Contour of bead, undercut, or shoulder is optional. “L” Style All-Purpose Thread (Plastic or Metal Closures) Threads/in. a b 12 i n. 0 .0 4 5 0 .0 3 0 m m 1 .1 4 0 .7 6 12 i n. 0 .0 4 5 0 .0 3 0 m m 1 .1 4 0 .7 6

“M” Style Modified Buttress Thread (Plastic Closures) Threads/in. a b 12 i n. 0. 05 1 0 .0 3 0 m m 1 .2 9 0 .7 6 12 i n. 0. 05 1 0 .0 3 0 m m 1 .2 9 0 .7 6

c 0 .0 1 6 0. 41 0 .0 1 6 0. 41

NOTE 2—Example Thread Nomenclature “L” Style: L15SP425 or“ M” Style M15SP425 NOTE 3—Corresponding dimensions and finish details are shown in Table in Table 6. 6. FIG. 4 SP 425 Finish Thread Thread Cross Sections Sections

determine conformity to be performed as agreed upon between the purchaser and the seller.

9. Rete Retest st and Rejection Rejection 9.1 If the results of any test do not conform conform to the requirements men ts of this specificat specification ion,, it is acc accepta eptable ble for retesting retesting to


6

D2911 − 10

*(See Footnote, e, Table e, Table 7 and 7 and Table 8) 8)

NOTE 1—Construction of neck from B to D must be held within the shaded area shown. NOTE 2—A minimum of 1 1 ⁄ 8 turns of thread shall be maintained. NOTE 3—Unless otherwise specified, I min applies to the full length of the opening. I min with respect to diameters T and E is not included. I min is specified for filler tube only. NOTE 4—Concentricity of I NOTE 5— T and and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. NOTE 6—Consideration must be given to the sealing surface width for the scaling system being used. NOTE 7—When valve style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition, it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter. NOTE 8—Top dimension is shown in inches: bottom dimension in millimeters. NOTE 9—Corresponding dimensions and finish details are shown in Table in Table 7 and 7 and Table 8. 8. FIG. 5 SP-103 Finish Finish and SP-100 Finish, Thread and Lip Cross Section


7

D2911 − 10

View: Section AA

NOTE 1—Construction of neck from B to D must be held within the shaded area shown. NOTE 2—A minimum of 1 1 ⁄ 2 turns of thread shall be maintained. NOTE 3—Unless otherwise specified, I min applies to the full length of the opening. I min with respect to diameters T and E is not included. I min is specified for filler tube only. NOTE 4—Concentricity of I NOTE 5— T and and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. NOTE 6—Consideration must be given to the sealing surface width for the sealing system being used. NOTE 7—When valve style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition, it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter. NOTE 8—Top dimension is shown in inches; bottom dimension in millimeters. FIG. 6 SP-200 Finish, Finish, Thread and Lip Section Section


8

D2911 − 10

T A

mm

28

m ax 1 . 08 8 2 7 .6 3

LIP Outsid Outside e Diameter

E A mi n 1 .0 6 8 2 7. 13

ma x 0. 98 4 2 4 .9 9

mi n 0 .9 6 4 2 4. 49

max 0 .9 7 4 2 4 .7 4

mi n 0 .9 5 4 2 4 .2 3

M

B

max mi n max 1.700 1. 1 .6 7 0 1 .0 6 2 43.10 42.42 26.97 43

Helix Angle

D

Y

IB , C

m ax 1 .3 2 0 33.53 33

constru st ruct ctio ion n 1. 18 8 3 0. 17

min min 0 .7 3 5 1 8 .6 7

2°13

8

Cutter Diameter

0. 37 5 9 .5 2

Threads Pitch per Inch

8

0. 12 5 3 .1 8

A

T and E and E dimensions dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. B Unless otherwise specified, I specified, I min min applies to the full length of the opening. C Concentricity of I of I min min with respect to diameters T diameters T and and E E is is not included. I included. I min min is specified for filler tube only.

NOTE 1—Constriction of neck from B to D must be held within the shaded area shown. NOTE 2—A minimum of 1 1 ⁄ 8 turns of thread shall be maintained. NOTE 3—Consideration must be given to the sealing surface width for the sealing system being used. NOTE 4—When valve style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition, it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter. FIG. 7 SP-1 SP-110 10 Finish Finish


9

D2911 − 10

NOTE 1—This finish drawing was established by PBI to provide plastic bottle finishes comparable to 445, 450, and 480 glass finishes. NOTE 2—Dimension H is measured from top of the finish to the point where diameter T , extended parallel to the centerline, intersects the shoulder or bead. NOTE 3—A minimum of 1 1 ⁄ 8 turns of thread shall be maintained. NOTE 4—Contour of bead, undercut, or shoulder is optional. NOTE 5—Unless otherwise specified. I min applies to the full length of the opening. I min with respect to diameters and T and E is not included. I min is specified for filler tube only. NOTE 6—Concentricity of I NOTE 7— T and and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. NOTE 8—Consideration must be given to the sealing surface width for the sealing system being used. NOTE 9—When valve style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition, it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter. FIG. 8 SP-444 Finish


10

D2911 − 10 TABLE 3 SP-400 Finish for Plastic Bottles Bottles

NOTE 1—Top dimension in each column shown in inches. Bottom dimension in each column shown in millimetres. TA

EA, B

HC

IDE

S

mm 18 20 22 24 28 30 33 35 38 40 43 45 48 51 53 58 60 63 66 70 75 77 83 89 1 00 110 12 0

Helix Angle,

m ax

mi n

m ax

mi n

max

mi n

max

mi n

mi n

b

0 .7 0 4 1 7 .8 8 0 .7 8 3 1 9 .8 9 0 .8 6 2 2 1 .8 9 0 .9 4 0 2 3 .8 8 1 .0 8 8 2 7 .6 3 1 .1 2 7 2 8 .6 2 1 .2 6 5 3 2 .1 3 1 .3 6 4 3 4 .6 4 1 .4 7 6 3 7 .4 9 1 .5 8 0 4 0 .1 3 1 .6 5 4 4 2 .0 1 1 .7 4 0 4 4 .2 0 1 .8 7 0 4 7 .5 0 1 .9 6 8 4 9 .9 9 2 .0 6 7 5 2 .5 0 2 .2 2 4 5 6 .4 9 2 .3 4 2 5 9 .4 9 2 .4 6 1 6 2 .5 1 2 .5 7 9 6 5 .5 1 2 .7 3 6 6 9 .4 9 2 .9 1 3 7 3 .9 9 3 .0 3 5 7 7 .0 9 3 .2 6 8 8 3 .0 1 3.511 8 9 .1 8 3 .9 3 7 1 0 0 .0 0 4 .3 3 1 110.01 4 .7 2 4 119.99

0 .6 8 8 1 7 .4 7 0 .7 6 7 1 9 .4 8 0 .8 4 6 2 1 .4 9 0 .9 2 4 2 3 .4 7 1 .0 6 8 2 7 .1 3 1 .1 0 7 2 8 .1 2 1 .2 4 1 3 1 .5 2 1 .3 4 0 3 4 .0 4 1 .4 5 2 3 6 .8 8 1 .5 5 0 3 9 .3 7 1 .6 2 4 4 1 .2 5 1 .7 1 0 4 3 .4 3 1 .8 4 0 4 6 .7 4 1 .9 3 3 4 9 .1 0 2 .0 3 2 5 1 .6 1 2 .1 8 9 5 5 .6 0 2 .3 0 7 5 8 .6 0 2 .4 2 6 6 1 .6 2 2 .5 4 4 6 4 .6 2 2 .7 0 1 6 8 .6 0 2 .8 7 8 7 3 .1 0 3 .0 0 0 7 6 .2 0 3 .2 3 3 8 2 .1 2 3 .4 7 6 8 8 .2 9 3. 90 2 99.11 4. 29 6 1 0 9. 12 4. 68 9 119.10

0 .6 2 0 1 5 .7 5 0 .6 9 9 1 7 .7 5 0 .7 7 8 1 9 .7 6 0 .8 5 6 2 1 .7 4 0 .9 9 4 2 5 .2 5 1 .0 3 3 2 6 .2 4 1 .1 7 1 2 9 .7 4 1 .2 7 0 3 2 .2 6 1 .3 8 2 3 5 .1 0 1 .4 8 6 3 7 .7 4 1 .5 6 0 3 9 .6 2 1 .6 4 6 4 1 .8 1 1 .7 7 6 45.11 1 .8 7 4 4 7 .6 0 1 .9 7 3 50.11 2 .1 3 0 5 4 .1 0 2 .2 4 8 5 7 .1 0 2 .3 6 7 6 0 .1 2 2 .4 8 5 6 3 .1 2 2 .6 4 2 67.11 2 .8 1 9 7 1 .6 0 2 .9 4 1 7 4 .7 0 3 .1 4 8 7 9 .9 6 3 .3 9 1 8 6 .1 3 3. 81 7 9 6 .9 5 4.211 1 0 6 .9 6 4. 60 4 116.94

0 .6 0 4 1 5. 34 0 .6 8 3 1 7. 35 0 .7 6 2 1 9. 35 0 .8 4 0 2 1. 34 0 .9 7 4 2 4. 74 1 .0 1 3 2 5. 73 1 .1 4 7 2 9. 13 1 .2 4 6 3 1. 65 1 .3 5 8 3 4. 49 1 .4 5 6 3 6. 98 1 .5 3 0 3 8. 86 1 .6 1 6 4 1. 05 1 .7 4 6 4 4. 35 1 .8 3 9 4 6. 71 1 .9 3 8 4 9. 22 2 .0 9 5 5 3. 21 2 .2 1 3 5 6. 21 2 .3 3 2 5 9. 23 2 .4 5 0 6 2. 23 2 .6 0 7 6 6. 22 2 .7 8 4 7 0. 71 2 .9 0 6 7 3. 81 3.113 7 9. 07 3 .3 5 6 8 5. 24 3 .7 8 2 9 6 .0 6 4 .1 7 6 1 0 6. 07 4 .5 6 9 116.05

0. 38 6 9 .8 0 0. 38 6 9 .8 0 0. 38 6 9 .8 0 0. 41 5 1 0 .5 4 0. 41 5 1 0 .5 4 0. 41 8 1 0 .6 2 0. 41 8 1 0 .6 2 0. 41 8 1 0 .6 2 0. 41 8 1 0 .6 2 0. 41 8 1 0 .6 2 0. 41 8 1 0 .6 2 0. 41 8 1 0 .6 2 0. 41 8 1 0 .6 2 0. 42 3 1 0 .7 4 0. 42 3 1 0 .7 4 0. 42 3 1 0 .7 4 0. 42 3 1 0 .7 4 0. 42 3 1 0 .7 4 0. 42 3 1 0 .7 4 0. 42 3 1 0 .7 4 0. 42 3 1 0 .7 4 0. 50 2 1 2 .7 5 0. 50 2 1 2 .7 5 0. 55 0 1 3 .7 9 0 .6 1 2 1 5. 54 0 .6 1 2 1 5 .5 4 0 .7 0 0 1 7 .7 8

0 .3 5 6 9 .0 4 0 .3 5 6 9 .0 4 0 .3 5 6 9 .0 4 0 .3 8 5 9 .7 8 0 .3 8 5 9 .7 8 0 .3 8 8 9 .8 5 0 .3 8 8 9 .8 5 0 .3 8 8 9 .8 5 0 .3 8 8 9 .8 5 0 .3 8 8 9 .8 5 0 .3 8 8 9 .8 5 0 .3 8 8 9 .8 5 0 .3 8 8 9 .8 5 0 .3 9 3 9 .9 8 0 .3 9 3 9 .9 8 0 .3 9 3 9 .9 8 0 .3 9 3 9 .9 8 0 .3 9 3 9 .9 8 0 .3 9 3 9 .9 8 0 .3 9 3 9 .9 8 0 .3 9 3 9 .9 8 0 .4 7 2 11.99 0 .4 7 2 11.99 0 .5 2 0 1 3. 21 0 .5 8 2 1 4 .7 8 0 .5 8 2 1 4. 78 0 .6 7 0 1 7. 02

0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 7 5 1 .9 0 0 .0 7 5 1 .9 0 0 .0 7 5 1 .9 0 0 .0 7 5 1. 90 0 .0 7 5 1. 90 0 .0 7 5 1. 90

0 .0 2 2 0. 56 0 .0 2 2 0. 56 0 .0 2 2 0. 56 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 3 1 0 .7 9 0 .0 4 5 1 .1 4 0 .0 4 5 1 .1 4 0 .0 4 5 1 .1 4 0 .0 4 5 1. 14 0 .0 4 5 1 .1 4 0 .0 4 5 1 .1 4

0 .3 2 5 8 .2 5 0 .4 0 4 1 0. 26 0 .4 8 3 1 2. 27 0 .5 1 6 13.11 0 .6 1 4 1 5. 59 0 .6 5 3 1 6. 59 0 .7 9 1 2 0. 09 0 .8 7 5 2 2. 22 0 .9 8 7 2 5. 07 1 .0 9 1 2 7. 71 1 .1 6 5 2 9. 59 1 .2 5 1 3 1. 77 1 .3 8 1 3 5. 08 1 .4 7 9 3 7. 57 1 .5 7 8 4 0. 08 1 .7 3 5 4 4. 07 1 .8 5 3 4 7. 07 1 .9 7 2 5 0. 09 2 .0 9 0 5 3. 09 2 .2 4 7 5 7. 07 2 .4 2 4 6 1. 57 2 .5 4 6 6 4. 67 2 .7 5 3 6 9. 93 2 .9 1 8 7 4. 12 3 .3 4 4 8 4 .9 4 3 .7 3 7 9 4 .9 2 4 .1 3 1 1 0 4 .9 3

3 °30 3°

3°7

2 °49 2°

2 °34 2°

2 °57 2°

2 °51 2°

2 °31 2°

2 °21 2°

2°9

2°0

1 °55 1°

1 °49 1°

1 °41 1°

1 °36 1°

1 °31 1°

1 °25 1°

1 °20 1°

1 °16 1°

1 °13 1°

1°8

1°4

1°1

1°9

1°4

0 °57 0°

0 °51 0°

0 °47 0°

A

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

8

Cutter Diameter

ThreadsF per Inch

0..375 0 9. 52 0.375 0. 9 .5 2 0.375 0. 9 .5 2 0.375 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2. 70 0.500 0. 1 2 .7 0 0.500 0. 1 2 .7 0 0.500 0. 1 2 .7 0 0.500 0. 1 2 .7 0 0.500 0. 1 2 .7 0 0.500 0. 1 2 .7 0

8 8 8 8 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 5 5 5 5 5

T and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and the container customer, as necessary. B Consideration must be given to the sealing surface width for the sealing system being used. C Dimension H is measured from the top of the finish to the point where diameter T, extended parallel to the centerline, intersects the bead or shoulder. D Unless otherwise specified, I minimum applies to the full length of the opening. E Concentricity of I minimum with respect to diameter T and E is not included. I minimum is specified for filler tube only. F A minimum of 1 full turn of thread shall be maintained.


11



EA, B

HC

LD

S

IEF

W

mm 18 20 22 24 28

Helix Angle,

max

mi n

max

mi n

m ax

mi n

mi n

max

mi n

mi n

max

b

0 .7 0 4 1 7 .8 8 0 .7 8 3 1 9 .8 9 0 .8 6 2 2 1 .8 9 0 .9 4 0 2 3 .8 8 1 .0 8 8 2 7 .6 3

0 .6 8 8 1 7 .4 7 17 0 .7 6 7 1 9 .4 8 19 0 .8 4 6 2 1 .4 9 21 0 .9 2 4 2 3 .4 7 23 1 .0 6 8 2 7 .1 3

0 .6 2 0 1 5 .7 5 0 .6 9 9 1 7 .7 5 0 .7 7 8 1 9 .7 6 0 .8 5 6 2 1 .7 4 0 .9 9 4 2 5 .2 5

0 .6 0 4 1 5. 34 0 .6 8 3 1 7. 35 0 .7 6 2 1 9. 35 0 .8 4 0 2 1. 34 0 .9 7 4 2 4. 74

0 .5 3 8 1 3. 66 0 .5 6 9 1 4. 45 0 .6 0 0 1 5. 24 0 .6 6 1 1 6. 79 0 .7 2 3 1 8. 36

0. 50 8 1 2 .9 0 0. 53 9 1 3 .6 9 0. 57 0 1 4 .4 8 0. 63 1 1 6 .0 3 0. 69 3 1 7 .6 0

0 .3 6 1 9 .1 7 0 .3 6 1 9 .1 7 0 .3 7 6 9 .5 5 0 .4 3 7 11.10 0 .4 6 3 11.76

0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5

0 .0 2 2 0 .5 6 0 .0 2 2 0 .5 6 0 .0 2 2 0 .5 6 0 .0 3 1 0. 79 0 .0 3 1 0. 79

0 .3 2 5 8. 2 5 0 .4 0 4 1 0. 26 0 .4 8 3 1 2. 27 0 .5 1 6 13.11 0 .6 1 4 1 5. 59

0 .0 8 4 2 .1 3 0 .0 8 4 2. 13 0 .0 8 4 2. 13 0 .0 8 4 2 .1 3 0 .0 9 4 2 .3 9

3 °3 0

8

3 °7

8

2 °4 9

8

2 °3 4

8

2 °5 7

8

Cutter Diameter

ThreadsG per Inch

0. 37 5 9 .5 2 0.375 0. 9. 52 0. 37 5 9. 52 0. 37 5 9 .5 2 0. 50 0 1 2 .7 0

8 8 8 8 6

A

T and E and E dimensions dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. B Consideration must be given to the sealing surface width for the sealing system being used. C Dimension H Dimension H is is measured from the top of the finish to the point where diameter T diameter T , extend extended ed parall parallel el to the centerline, intersects intersects the shoulder. shoulder. D Contour of bead, undercut, or shoulder is optional. If bead is used, bead diameter and L and L min must be maintained. E Unless otherwise specified, I specified, I min min applies to the full length of the opening. F Concentricity of I of I min min with respect to diameters T diameters T and and E E is not included. I included. I min min is specified for filler tube only. G A minimum of 11 ⁄ 2 full turns of thread shall be maintained.

TABLE 5 SP-415 Finish for Plastic Bottles Bottles


EA, B

HC

LD

S

IEF

W

mm 13 15 18 20 22 24 28 33

Helix Angle,

max

mi n

max

mi n

max

mi n

mi n

max

mi n

mi n

max

b

0 .5 1 4 1 3 .0 6 0 .5 8 1 1 4 .7 6 0 .7 0 4 1 7 .8 8 0 .7 8 3 1 9 .8 9 0 .8 6 2 2 1 .8 9 0 .9 4 0 2 3 .8 8 1 .0 8 8 2 7 .6 3 1 .2 6 5 3 2 .1 3

0. 50 2 1 2. 75 0. 56 9 1 4. 45 0. 68 8 1 7. 47 0. 76 7 1 9. 48 0. 84 6 2 1. 49 0. 92 4 2 3. 47 1. 06 8 2 7. 13 1. 24 1 3 1. 52

0 .4 5 4 11.53 0 .5 2 1 1 3. 23 0 .6 2 0 1 5. 75 0 .6 9 9 1 7. 75 0 .7 7 8 1 9. 76 0 .8 5 6 2 1. 74 0 .9 9 4 2 5. 25 1 .1 7 1 2 9. 74

0 .4 4 2 11.23 0 .5 0 9 1 2. 93 0 .6 0 4 1 5. 34 0 .6 8 3 1 7. 35 0 .7 6 2 1 9. 35 0 .8 4 0 2 1. 34 0 .9 7 4 2 4. 74 1 .1 4 7 2 9. 13

0. 46 7 11.86 0. 57 2 1 4. 53 0. 63 2 1 6. 05 0. 75 7 1 9. 23 0. 85 2 2 1. 64 0. 97 2 2 4. 69 1. 09 7 2 7. 86 1. 28 9 3 2. 74

0 .4 3 7 11.10 0 .5 4 2 1 3 .7 7 0 .6 0 2 1 5 .2 9 0 .7 2 7 1 8 .4 7 0 .8 2 2 2 0 .8 8 0 .9 4 2 2 3 .9 3 1 .0 6 7 2 7 .1 0 1 .2 5 9 3 1 .9 8

0 .3 0 6 7 .7 7 0 .3 4 8 8 .8 4 0 .4 2 9 1 0 .9 0 0 .4 5 6 11.58 0 .5 4 6 1 3 .8 7 0 .5 6 1 1 4 .2 5 0 .6 5 5 1 6 .6 4 0 .7 7 2 1 9 .6 1

0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 5 2 1 .3 2 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5 0 .0 6 1 1 .5 5

0 .0 2 2 0 .5 6 0 .0 2 2 0 .5 6 0 .0 2 2 0. 56 0 .0 2 2 0. 56 0 .0 2 2 0. 56 0 .0 3 1 0. 79 0 .0 3 1 0. 79 0 .0 3 1 0. 79

0 .2 1 8 5. 5 4 0 .2 5 8 6. 5 5 0 .3 2 5 8. 25 0 .4 0 4 1 0. 26 0 .4 8 3 1 2. 27 0 .5 1 6 13.11 0 .6 1 4 1 5. 59 0 .7 9 1 2 0. 09

0 .0 4 5 1 .1 4 0 .0 4 5 1 .1 4 0 .0 8 4 2. 13 0 .0 8 4 2 .1 3 0 .0 8 4 2 .1 3 0 .0 8 4 2 .1 3 0 .0 9 4 2 .3 9 0 .0 9 4 2 .3 9

3°11

8

2 °4 8

8

3 °3 0

3 °7

A

8

8

2 °4 9

8

2 °3 4

8

2 °5 7

8

2 °3 1

8

Cutter Diameter

ThreadsG per Inch

0..375 0 9. 52 0.375 0. 9. 52 0.375 0. 9 .5 2 0.375 0. 9. 52 0.375 0. 9. 52 0.375 0. 9. 52 0.500 0. 1 2. 70 0.500 0. 1 2. 70

12 12 8 8 8 8 6 6

T and E and E dimensions dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. B Consideration must be given to the sealing surface width for the sealing system being used. C Dimension H Dimension H is is measured from the top of the finish to the point where diameter T diameter T , extend extended ed parall parallel el to the centerline, intersects intersects the shoulder. shoulder. D Contour of bead, undercut, or shoulder is optional. If bead is used, bead diameter and L and L min must be maintained. E Unless otherwise specified, I specified, I min min applies to the full length of the opening. F Concentricity of I of I min min with respect to diameters T diameters T and and E E is not included. I included. I min min is specified for filler tube only. G A minimum of 2 full turns of thread shall be maintained.


12


NOTE 1—Top dimension in each column shown in inches. Bottom dimension in each column shown in millimetres. mm 13 15

T A

E A,

B

H C

S D

I E , F

max

mi n

m ax

mi n

max

mi n

max

mi n

mi n

0 .5 1 4 1 3. 06 0 .5 8 1 1 4. 76

0 .5 0 2 1 2 .7 5 0 .5 6 9 1 4 .2 5

0 .4 5 4 11.53 0 .5 2 1 1 3. 23

0. 44 2 11.23 0. 50 9 1 2 .9 3

0 .3 2 5 8. 25 0 .3 2 5 8. 25

0. 29 5 7 .4 9 0. 29 5 7 .4 9

0. 05 2 1 .3 2 0. 05 2 1 .3 2

0. 02 2 0 .5 6 0. 02 2 0 .5 6

0. 2 1 8 5 .5 4 0. 2 5 8 6 .5 5

Helix Angle b

Cutter Diameter

ThreadsG per Inch

3°11

0 .3 7 5 9 .5 2 0 .3 7 5 9 .5 2

12

8

2°48

8

12

A

T and E and E dimensions dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. B Consideration must be given to the sealing surface width for the sealing system being used. C Dimension H Dimension H is is measured from the top of the finish to the point where diameter T diameter T , extend extended ed parall parallel el to the centerline, intersects intersects the shoulder. shoulder. D Contour of bead, undercut, or shoulder is optional. E Unless otherwise specified, I specified, I min min applies to the full length of the opening. F Concentricity of I of I min min with respect to diameters T diameters T and and E E is is not included in this standard. I standard. I min min is specified for filler tube only. G A minimum of 2 full turns of thread shall be maintained on the bead finish. A minimum of 11 ⁄ 2 full turns of thread shall be maintained on the beadless finish.


NOTE 1—Top dimension in each column shown in inches. Bottom dimension in each column shown in millimetres. T A

mm 22 24 26 28 38

E A,

B

LIP Outsid Outside e DiameterD

H C

I E , F , G

max

mi n

max

mi n

max

mi n

ma x

mi n

mi n

0 .8 6 2 2 1 .8 9 0 .9 4 0 2 3 .8 8 1 .0 0 9 2 5 .6 3 1 .0 8 8 2 7 .6 3 1 .4 7 6 3 7 .4 9

0 .8 4 6 2 1 .4 9 0 .9 2 4 2 3 .4 7 0 .9 8 9 2 5 .1 2 1 .0 6 8 2 7 .1 3 1 .4 5 2 3 6 .8 8

0. 75 8 1 9 .2 5 0. 83 6 2 1 .2 3 0. 90 5 2 2 .9 9 0. 98 4 2 4 .9 9 1. 37 2 3 4 .8 5

0 .7 4 2 1 8 .8 5 0 .8 2 0 2 0 .8 3 0 .8 8 5 2 2 .4 8 0 .9 6 4 2 4 .4 9 1 .3 4 8 3 4 .2 4

0 .5 5 9 1 4 .2 0 0 .5 5 9 1 4 .2 0 0 .5 5 9 1 4 .2 0 0 .5 5 9 1 4 .2 0 0 .6 0 4 1 5 .3 4

0 .5 2 9 1 3 .4 4 0 .8 2 9 1 3 .4 4 0 .5 2 9 1 3 .4 4 0 .5 2 9 1 3 .4 4 0 .5 7 4 1 4 .5 8

0 .7 4 8 1 9. 00 0 .8 2 6 2 0. 98 0 .8 9 5 2 2. 73 0 .9 7 4 2 4. 74 1 .3 6 2 3 4. 59

0 .7 3 2 18 . 59 0 .8 1 0 20 . 57 0 .8 7 5 22 . 22 0 .9 5 4 24 . 23 1 .3 3 8 33 . 98

0 5. 12 1 3 .0 0 0 .5 9 0 1 4 .9 9 0 .6 5 5 1 6 .6 4 0 .7 3 5 1 8 .6 7 1 .0 9 8 2 0 .8 9

Helix Angle b

Cutter Diameter

ThreadsH per Inch

2 °4 9

0 .3 7 5 9. 52 0 .3 7 5 9. 52 0 .3 7 5 9. 52 0 .3 7 5 9. 52 0 .3 7 5 9. 52

8

8

2 °3 4

8

2 °2 4

8

2 °1 3

8

1 °3 7

8

8 8 8 8

A

T and E and E dimensions dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer as necessary. B Consideration must be given to the sealing surface width for the sealing system being used. C Dimension H Dimension H is is measured from the top of the finish to the point where diameter T diameter T , extend extended ed parall parallel el to the centerline, intersects intersects the shoulder. shoulder. D Contour of undercut or shoulder is optional. E Unless otherwise specified, I specified, I min min applies to the full length of the opening. F Concentricity of I of I min min with respect to diameters T diameters T and and E E is not included. I included. I min min is specified for filler tube only. G When valve style closures are used with this finish, special consideratio consideration n must be given to a specifi specific c controlled inside diameter. diameter. In additi addition, on, it is acceptable to vary the dimensions indicated with an asterisk (*) on Fig. on Fig. 5 to 5 to ensure adequate adequate materi material al for finishi finishing ng the inside diameter. diameter. H A minimum of 11 ⁄ 8 turns of thread shall be maintained.



mm 26

ma x 1. 00 9 2 5. 63

E A, mi n 0 .9 8 9 2 5 .1 2

m ax 0 .9 0 5 2 2. 99

B

H C mi n 0 .8 8 5 2 2 .4 8

m ax 0. 63 8 1 6 .2 0

A

mi n 0 .6 0 8 1 5 .4 4

LIP Outsid Outside e DiameterD max mi n 0 .8 9 5 0. 87 5 2 2. 73 2 2 .2 2

I E , F , G mi n 0 .6 7 0 1 7 .6 2

Helix Angle b 2 °2 4

8

Cutter ThreadsH Diameter per Inch 0 .3 7 5 9. 52

8

T and E and E dimensions dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer as necessary. B Consideration must be given to the sealing surface width for the sealing system being used. C Dimension H Dimension H is is measured from the top of the finish to the point where diameter T diameter T , extend extended ed parall parallel el to the centerline, intersects intersects the shoulder. shoulder. D Contour of undercut or shoulder is optional. E Unless otherwise specified, I specified, I min min applies to the full length of the opening. F Concentricity of I of I min min with respect to diameters T diameters T and and E E is not included. I included. I min min is specified for filler tube only. G When valve style closures are used with this finish, special consideratio consideration n must be given to a specifi specific c controlled inside diameter. diameter. In additi addition, on, it is acceptable to vary the dimensions indicated with an asterisk (*) on Fig. on Fig. 5 to 5 to ensure adequate adequate materi material al for finishi finishing ng the inside diameter. diameter. H A minimum of 11 ⁄ 8 turns of thread shall be maintained.


13



mm 24 28

E A,

B

LIP Outsid Outside e DiameterD

H C

I E , F , G

m ax

mi n

m ax

mi n

max

mi n

max

mi n

min

0 .9 4 0 2 3 .8 8 1.118 2 8 .4 0

0 .9 2 4 2 3. 47 1 .0 9 8 2 7. 89

0 .8 3 2 21 . 13 1 .0 1 0 25 . 65

0 .8 1 6 2 0 .7 3 0 .9 9 0 2 5 .1 5

0 .8 0 9 2 0. 55 0 .8 0 9 2 0. 55

0 .7 7 9 1 9 .7 9 0 .7 7 9 1 9 .7 9

0 .8 2 2 2 0 .8 8 1 .0 0 0 2 5 .4 0

0. 80 6 2 0 .4 7 0. 98 0 2 4 .8 9

0. 54 0 1 3 .7 2 0. 71 0 1 8 .0 3

A

Helix Angle b

Cutter Diameter

ThreadsH per Inch

3°27

0 .3 7 5 9. 52 0 .3 7 5 9. 52

6

8

2°53

8

6

Alternate H Alternate H dimensions dimensions are recognized and will be designated as SP200A: Alt. H Alt. H 24 mm, 0.789/0.759 20.04/19.28 Alt. H Alt. H 28 mm, 0.823/0.793 20.90/20.14 T and and E E dimensions dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by the container supplier and container customer, as necessary. B Consideration must be given to the sealing surface width for the sealing system being used. C Dimension H Dimension H is is measured from the top of the finish to the point where diameter T diameter T , extend extended ed parall parallel el to the centerline, intersects intersects the shoulder. shoulder. D Contour of undercut or shoulder is optional. E Unless otherwise specified, I specified, I min min applies to the full length of the opening. F Concentricity of I of I min min with respect to diameters T diameters T and and E E is not included. I included. I min min is specified for filler tube only. G When valve style closures are used with this finish, special consideratio consideration n must be given to a specifi specific c controlled inside diameter. diameter. In additi addition, on, it is acceptable to vary the dimensions indicated with asterisk (*) on Fig. on Fig. 6 to 6 to ensure adequate adequate materi material al for finishi finishing ng the inside diameter. diameter. H A minimum of 11 ⁄ 2 turns of thread shall be maintained.


14

D2911 − 10 APPENDIX (Nonmandatory Information) X1. EST ESTABLISHING ABLISHING PLASTIC BOTTLE FINISHES

X1.1 Objec Objective tive X1.1.1 The fol X1.1.1 follow lowing ing pro proced cedure uress are rec recomm ommend ended ed as a guide for establishing plastic bottle finishes. The objective is to provid pro videe a bas basis is of com common mon und unders erstan tandin ding g for all con contain tainer er suppli sup pliers ers that may be hel helpfu pfull to the them m in dev develop eloping ing finish dimensions that fall outside the present range of finish dimensions developed and when converting glass finishes to plastic. X1.2 Determinati Determination on of Finish Dimensions X1.2.1 H Dimensions— To To determine H , use maximu maximum m H of of closu clo sure re min minus us co comp mpre ress ssed ed lin liner er an and d ad add d an am amou ount nt fo forr desirable clearance (preferably 0.015 in. or 0.38 mm). This will be minimu minimum m H . For maximum H dimensions, add 0.030 in. or 0.76 mm to minimum H . H dimension dimension is measured from the top of the finish to the point where diameter T extended extended parallel to centerline intersects the bead or shoulder. and d E Di Dime mens nsio ions ns To deter X1.2.2 T an determine mine T and E

X1.2.4 I Minimum— Minimum Minimum dimension must be specified. It should be recognized that this is for filler tube clearance only. X1.2.5 S Dimens All conven conventional tional contin continuous uous thread Dimension— ion— All finishes use the SP-400 S Dimension. Dimension. When a pour-out finish is involved, the SP-100 finish should be used as a guide. X1.2.6 L Dimension— Refer Refer to SP-410 and SP-415 finishes where a bead is used within an H dimension. X1.2.7 Use Special consid consideration eration Use of In Inter terna nall Fit Fitme ments nts— — Special should sho uld be giv given en whe whenev never er con contro trolled lled int intern ernal al dia diamete meters rs are required because of use with internal fitments. The controlled intern int ernal al diam diameter eter mus mustt pro provid videe the req requir uired ed int interf erfere erence nce to satisfy sati sfy the fun functio ctional nal nee need. d. Spe Specifi cified ed T and E dimensions should be maintained after insertion of the fitment. It should be note no ted d th that at th thee fit fitme ment nt is no nott a pa part rt of co cont ntai aine nerr S or H dimension.

D2911 − 10 APPENDIX (Nonmandatory Information) X1. EST ESTABLISHING ABLISHING PLASTIC BOTTLE FINISHES

X1.2.4 I Minimum— Minimum Minimum dimension must be specified. It should be recognized that this is for filler tube clearance only.

X1.1 Objec Objective tive X1.1.1 X1. 1.1 The fol follow lowing ing pro proced cedure uress are rec recomm ommend ended ed as a guide for establishing plastic bottle finishes. The objective is to provid pro videe a bas basis is of com common mon und unders erstan tandin ding g for all con contain tainer er suppli sup pliers ers that may be hel helpfu pfull to the them m in dev develop eloping ing finish dimensions that fall outside the present range of finish dimensions developed and when converting glass finishes to plastic.

X1.2.5 S Dimens All conven conventional tional contin continuous uous thread Dimension— ion— All finishes use the SP-400 S Dimension. Dimension. When a pour-out finish is involved, the SP-100 finish should be used as a guide. X1.2.6 L Dimension— Refer Refer to SP-410 and SP-415 finishes where a bead is used within an H dimension.

X1.2 Determinati Determination on of Finish Dimensions

X1.2.7 Use Special consid consideration eration Use of In Inter terna nall Fit Fitme ments nts— — Special should be giv should given en whe whenev never er con contro trolled lled int intern ernal al dia diamete meters rs are required because of use with internal fitments. The controlled intern int ernal al diam diameter eter mus mustt pro provid videe the req requir uired ed int interf erfere erence nce to satisfy sati sfy the fun functio ctional nal nee need. d. Spe Specifi cified ed T and E dimensions should be maintained after insertion of the fitment. It should be note no ted d th that at th thee fit fitme ment nt is no nott a pa part rt of co cont ntai aine nerr S or H dimension.

X1.2.1 H Dimensions— To To determine H , use maximu maximum m H of of closu clo sure re min minus us co comp mpre ress ssed ed lin liner er an and d ad add d an am amou ount nt fo forr desirable clearance (preferably 0.015 in. or 0.38 mm). This will be minimu minimum m H . For maximum H dimensions, add 0.030 in. or 0.76 mm to minimum H . H dimension dimension is measured from the top of the finish to the point where diameter T extended extended parallel to centerline intersects the bead or shoulder. and d E Di Dime mens nsio ions ns— — To deter X1.2.2 T an determine mine T and E dimensions, maintain maximum SP SP finish dimensions as shown in Tables in Tables 1-10, 1-10, using the SP finish tolerances with corresponding neck size (millimetres).

X1.2.8 Thread The SPSP-400 400 L style style or M style Thread Pro Profile— file— The profile pro file sho should uld be util utilized ized when con contin tinuou uouss thr thread eadss are required.

X1.2.3 T and E Dimensions are the average of two measureme sure ment ntss ac acro ross ss th thee ma majo jorr an and d mi mino norr ax axis. is. Th Thee lim limit itss of oval ov ality ity wi will ll be de deter termi mine ned d by th thee co cont ntai aine nerr su supp pplie lierr an and d container customer.

X1.2.9 X1.2 .9 A mi mini nimu mum m of 1 fu full ll tu turn rn of th thre read ad sh shou ould ld be maintained.

ASTM International International takes no positi position on respecting the validi validity ty of any patent rights assert asserted ed in connec connection tion with any item mentio mentioned ned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible respon sible technical technical committee, which you may attend. If you feel that your comments have not receiv received ed a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address addr ess or at 610610-832832-9585 9585 (pho (phone), ne), 610610-832832-9555 9555 (fax (fax), ), or serv service@ ice@astm astm.org .org (e-m (e-mail) ail);; or thro through ugh the ASTM webs website ite (www.astm. (www .astm.org). org). Permission Permission rights to photocopy the standa standard rd may also be secure secured d from the ASTM website (www.astm.or (www.astm.org/ g/ COPYRIGHT/).


16

ASTM D2911-10

Recommend Documents