Anti-theft Rematching And Remote Control Rematching Rematching Manual
Anti-theft Rematching And Remote Control Rematching Manual
Anti-theft Rematching Manual of QQ6/A1/A15/A21/B11/T1 QQ6/A1/A15/A21/B11/T11/B14/A3/S18 1/B14/A3/S18 1. Connect X-341 OBD OBD II connector with with vehicle;
2. Turn on ignition switch;
3. Turn on X-431 and then select A15
series/B11 series/QQ6 series/T11 3 series/A5 series/B11 cross series/A1 series/A3 (Sedan) series/A3(Hatchback) series according your need; !
For the vehicle of S18(M1), please click Riich series and select Riich M1 ;
TB-E-10-016
!
-1-
!
Chery International After-Sales Service Department Department
PDF !"# "pdf "pdf Fact Facto or y Pr o" $#%&'( www. f i nepr i nt . co com m.cn
Anti-theft Rematching And Remote Control Rematching Manual
4. Select IMMO ;
!
5. Click input code and input PIN code
!
( you can get PIN code from Chery DMS), then click the small keyboard to close the window to display OK button;
!
For the vehicle of M11/M12, please click Actuation test , select Program key ,
!
!
click match keys , and input PIN, then click
!
the small keyboard to quit the input;
TB-E-10-016
-2-
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
6. Click OK ;
!
7. Select immobilizer adapt ;
!
Note: If your vehicle is M11/M12, this step is not needed; For the vehicle of S18, firstly select read
immobilizer to EMS and click OK , secondly !
!
select read EMS to immobilizer and click OK ,
!
!
thirdly select key learning and click OK ;
!
!
8. If ECU has been replaced, please select Read immobilizer to EMS , and then select
!
key learning ; If immobilizer has been replaced,
!
please select read EMS to immobilizer , and
!
then select key learning ;
!
If ECU and immobilizer have been replaced at the same time, chip must be changed also, TB-E-10-016
-3-
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
and then select read immobilizer to EMS ,
!
and then select read EMS to immobilizer ,
!
and then select key learning ;
!
If only chip is replaced, you can operate select key learning immediately;
!
9. Click OK when screen shows operation
!
succeeded ; !
10. Try to start engine. If it can be started, it means matching is successful;
11. If another key need to be rematched, firstly pull out the rematched key, and wait for 10 seconds, and then insert key to be rematched, and then repeat from step 1 to step 10.
TB-E-10-016
-4-
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
Remote Control Rematching Manual Tip: Please rematch two remote controls at one time, other wise, if you just rematch one remote control at one time, another remote control will not work. 1. Connect X-431 OBD II connector with vehicle; If your vehicle is M11/M12, please use CAN BUS II connector; For QQ6/A1/S18(M1), please insert key and put it on ACC position;
!
2. Turn on X-431 and select B11 series/
T11 3 series/ QQ6 series /A5 series/ A1 series /B11 cross series / A3 (Sedan) series/A3(Hatchback) series
!
according your need; For S18(M1), please select Riich series
!
and click Riich M1 ;
!
3. Select BCM or ISU ,and click OK ;
TB-E-10-016
!
!
-5-
!
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
4. Click key teach or Remoter match ;
!
!
5. Press locking button of remote control for 2 seconds and release the button. 5 seconds later, please press the locking button of another key if the second key need to be rematched. Click OK at last.
!
For the vehicle of QQ6/A1/S18(M1), press locking button of remote control 2 seconds and then click OK . If you need to rematch
!
the second key, please insert the key to ignition switch and turn it on, and repeat from step 3 to step 5.
TB-E-10-016
-6-
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
For the vehicle of QQ3, please rematch remote control as following steps:
1. Turn on and off ignition switch 3 times (OFF-ON-OFF-ON-OFF-ON) within 7 seconds;
2. Anti-theft indicator lamp will flash 3 seconds, pause 1 second, and then turn on again. Wait until the lamp goes off, turn off the ignition switch. Turn on ignition switch again and press any button of remote control; meanwhile anti-theft indicator lamp will flash once. It means rematching succeeded.
3. If you want to rematch another key, please press any button of remote control of the key within 10 seconds after the first rematching, or repeat the operation 1 and 2.
TB-E-10-016
-7-
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
For the vehicle of A15, please rematch remote control as following steps:
1. If the production date of A15 is earlier than Feb. 2010, please connect two pins of anti-theft indicator lamp harness connector (beside steering column) to short circuit;
2. Turn on ignition switch and wait anti-theft indicator lamp turns on;
3. Press any button of remote control. If the anti-theft indicator lamp goes off, it means rematching succeed.
TB-E-10-016
-8-
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
4. If you need to rematch another key, please wait the anti-theft indicator lamp turns on again, press any button of the key. If anti-theft indicator lamp goes off, it means the second key rematching succeed.
5. If the production date of A15 is after Feb. 2010, turn on ignition switch 3 times (OFF-ON-OFF-ON-OFF-ON) within 7 seconds; Anti-theft indicator lamp will flash 3 seconds, pause 1 second, and turns on for 1 second again, and then turn off;
6. Turn ignition switch ON-OFF-ON, and anti-theft indicator lamp will turn on again;
TB-E-10-016
-9-
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn
Anti-theft Rematching And Remote Control Rematching Manual
7. Press down any button of remote control and hold for more than 2 seconds; To rematch another key, you need to wait for 5 seconds, nd
and then press any button of 2 remote control more than 2 seconds. If anti-theft indicator lamp goes off, it means the rematching succeed.
Jim Wang Prepare
Culbert Leng
TB-E-10-016
- 10 -
Audit
Approval Frank Ouyang
Z eb i n g W u
Chery International After-Sales Service Department
PDF !"# "pdf Factory Pro" $#%&'( www. f i nepri nt . com.cn