Workshop 1 Taylor Impact Test – Basic Simulation
ANSYS Explicit Dynamics
Workshop 1. Taylor Impact T Test est – Basic Simulation
Workshop Goal and Procedure
Training Manual
Goal: Simulate the impact of rod into a plate (typically known as a “Taylor Test ”) ”)
Procedure: Create an Explicit Dynamics (ANSYS) Analysis System S ystem Project Select the unit system and assign the material properties Create the rod and plate geometry in DesignModeler Mesh the two parts and set the initial velocity condition of the rod Define the analysis settings, boundary conditions, and applied loads Initiate the solution (AUTODYN (AUTODYN - STR) and review review the results results
Workshop 1. Taylor Impact T Test est – Basic Simulation
Workshop Goal and Procedure
Training Manual
Goal: Simulate the impact of rod into a plate (typically known as a “Taylor Test ”) ”)
Procedure: Create an Explicit Dynamics (ANSYS) Analysis System S ystem Project Select the unit system and assign the material properties Create the rod and plate geometry in DesignModeler Mesh the two parts and set the initial velocity condition of the rod Define the analysis settings, boundary conditions, and applied loads Initiate the solution (AUTODYN (AUTODYN - STR) and review review the results results
Workshop 1. Taylor Impact T Test est – Basic Simulation
Step 1 – Create the Project Schematic
Training Manual
Start ANSYS Workbench and follow the sequenced steps using the abbreviations shown below: – – – –
Click with Left Mouse Button DC = Double Click with SC = Single Click with Click with Left Mouse Button Button Selection RMB = Right Mouse Button Selection Drop = Hold Left Mouse Button down on item while D&D = Drag and Drop = dragging it to new location and then release it (i.e., Copy or Move)
1. Create an ANSYS Explicit Dynamics Dynamics Analysis System System Project
DC
Workshop 1. Taylor Impact Test – Basic Simulation
Step 1 – Create the Project Schematic ... •
Training Manual
An alternate method to create the Project Schematic would have been to Drag and Drop the Explicit Dynamics (ANSYS) Analysis System onto the blank screen to the right as shown below. Please note that, throughout these Workshops, the procedures shown are not always the only way to accomplish the desired tasks, so feel free to investigate other methods via the documentation when outside of this course.
D&D
Workshop 1. Taylor Impact Test – Basic Simulation
Step 2 – Specify the Project Units
Training Manual
2.a Select MKS for the Project Units from the Units List provided
2.b Request that Native Applications in Workbench have their values be Displayed in the Project Units
Note: Engineering Data is native in Workbench, but DesignModeler and Mechanical are NOT currently (but will be in the future). Therefore, always check that the local units system is as desired.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 3 – Define Engineering Data Material DC
Training Manual
3.a Edit the Engineering Data cell to select pre-defined material models from one of the pre-defined material libraries. 3.b Select the General Non-linear Materials library. These materials have sufficient physical property data defined so that they can be used in both ANSYS implicit and explicit analyses.
SC
Note: The material models in the Explicit Materials library are generally more complicated and can only be used in explicit dynamic analyses.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 3 – Define Engineering Data Material ... 3.c Select the “+” sign to the right of the Aluminum Alloy NL material model to add it to the Engineering Data library.
3.d Likewise, select the “+” sign to the right of the Structural Steel NL material. Note the symbol of a book that appears indicating success.
SC
SC
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 3 – Define Engineering Data Material ... 3.e Return to the Engineering Data cell and note the added materials.
3.f Return to the Project Schematic 3.g Save the Project by selecting the “ Save As ” icon and Browse to the directory indicated by your instructor. Enter “taylor_basic ” for the Project name.
SC
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry
Training Manual
Note: The geometry for this workshop is created in Step 4 , starting on the next slide. However, this DesignModeler exercise may be skipped by importing the geometry database taylor_impact_geometry.agdb as shown below. If this file is imported, proceed directly to Step 5 .
RMB
SC
SC
Note: The course instructor will indicate the directory location of this file.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
RMB
Training Manual
4.a To create new geometry, follow the procedure shown. Double Clicking on the “Geometry ” cell will also work, since “New Geometry ...” is the default SC action for the Geometry cell when a geometry file is not already associated with the Project.
4.b Select Meter as the desired length unit. 4.c Select “Always use project unit ” to get around the problem of DesignModeler not currently being native in Workbench. When new geometry is created, the existing Project units will be used in DesignModeler.
4.d Select OK to enter DesignModeler (DM).
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
Training Manual
4.e Select the Sketching tab.
SC 4.f Next select the Circle tool from the Draw Toolbox. This tool requires that the center point be entered first followed by a point on the circle’s circumference.
SC
SC 4.g Use the Left Mouse Button (LMB) and click on graph origin (a “P” will appear when the mouse is over the origin). With the LMB still depressed, slide the pointer away from the center until a circle is created. Then let go of the LMB, completing the circle operation.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
Training Manual
4.h Select the General tool from the Dimensions Toolbox.
RMB
4.j Select the circle, creating dimension “R1”. Then enter 0.010 meters in the Details View for the circle radius.
Resize the graphics view, if desired.
4.i RMB select the Radius operation for the General Dimensions tool. This is a temporary selection of a dimension type.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
Training Manual
4.k Select the Extrude icon, which brings up the Modeling mode.
4.l Enter a Fixed Depth of 0.030 meters in the Normal Direction via the Details View.
4.m Select the Generate icon to complete the extrusion operation.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
Training Manual
4.n Return to the Sketching mode and create a new sketch (Sketch2 ) for the plate construction. 4.o Select the Rectangle tool from the Draw Toolbox and draw the rectangle shown by dragging the LMB, using the opposite corners of the rectangle to define it. 4.p The dimensions of the rectangle will be defined next, so now select the Dimensions Toolbox.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
Training Manual
4.q Select the General tool under the Dimensions Toolbox and dimension the lines on the top and right side to be 0.040 meters long. Since the rectangle is no longer centered about the circle, additional dimensions will need to be defined.
4.r For the next two dimensions, use the RMB to select the Horizontal and then the Vertical options, respectively.
RMB selections
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
Training Manual
4.s After specifying a Horizontal General dimension via the RMB, make sure that ONLY the Vertex filter is active. This will prevent lines from being accidentally selected, thereby simplifying the task. 4.t Select the origin , and while holding the Ctrl key down, select the top right corner of the rectangle to create dimension H4. Repeat this procedure (after specifying a Vertical General dimension via the RMB) with the same two points to create dimension V5. 4.u Enter 0.020 meters for both H4 and V5 in the Details View for these dimensions. The rectangle is now centered correctly.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ... 4.v Select the Extrude icon, which accesses the Modeling mode, and set the Operation to Add Frozen to prevent merging of the bodies. 4.w Enter a Fixed Depth of 0.010 m in the Reversed Direction .
4. x Extrude Sketch2 via Generate .
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 4 – Create the Geometry ...
Training Manual
4.y Rename the two solids to be Cylinder and Plate , respectively. Use the RMB after selecting the body in the tree to access the Rename function.
RMB
4.z Save the Project
The Cylinder is not frozen, but the Plate is frozen. Since the bodies touch each other, they would be merged into one body if both bodies were unfrozen.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 5 – Edit the Model in Mechanical 5.a Edit the model in Workbench Mechanical.
RMB
SC
5.b Select the MKS Units system – Recall that Mechanical is not native in Workbench, so the Units here may not match the Project Units
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 5 – Edit the Model in Mechanical ...
Training Manual
5.c Assign the material Aluminum Alloy NL to the Cylinder and the material Structural Steel NL to the Plate . To access the materials stored in the Engineering Data library, click on the default material currently assigned to the part, and a small fly-out arrow will appear. Clicking on that arrow lists the materials available for use.
SC
SC
SC
Workshop 1. Taylor Impact Test – Basic Simulation
Step 5 – Edit the Model in Mechanical ... 5.d Delete the automatically defined Contact Region . Alternatively, it can be changed from Type Bonded to Frictionless , but the existing Body Interactions are sufficient as shown below.
Training Manual
RMB
Penalty -based Trajectory contact is the default interaction and the type is Frictionless .
SC
Workshop 1. Taylor Impact Test – Basic Simulation
Step 6 – Set Sizing Controls and Mesh Model 6.a Select the Mesh branch 6.b Specify the Mesh Details : – Physics Preference = Explicit – Element Size = 0.003 meters
6.c Generate the mesh
RMB
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 7 – Define the Initial Conditions
Training Manual
7.a Apply an Initial Velocity Condition to the Cylinder as shown.
RMB
Note: If the Body SC selection filter is not automatically activated for the initial velocity condition, select it manually.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 7 – Define the Initial Conditions ...
7.b Choose to define the Initial Velocity by Components : – X = 0 m/sec – Y = 0 m/sec – Z = -300 m/sec
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 8 – Define the Analysis Settings SC
Training Manual
8.a Select Analysis Settings in the tree and set the End Time to be 2.0e-4 seconds in the Details View. 8.b Keep the remaining default settings.
8.c Twenty equally-spaced results sets should be sufficient for the animations.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 9 – Apply Boundary Conditions 9.a Pick the Face selection filter.
RMB 9.b Insert a Fixed Support on the back face of the Plate . Rotate the geometry, as needed.
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 10 – Insert Result Items to Postprocess RMB
10.a Insert a Directional Deformation plot request under the Solution branch and set the Orientation to the Z Axis in the Details View.
RMB 10.b Insert an Equivalent Plastic Strain plot request under the Solution branch.
10.c Save the Project.
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 11 – Run the AUTODYN Simulation 11.a Select Solver Output under Solution Information and RMB Solve to start the simulation.
RMB
11.b Note: The model is converted to an AUTODYN Cycle Zero database and submitted to the AUTODYN solver. The results are written to the standard AUTODYN files, but are also available in this product for review.
Training Manual
Workshop 1. Taylor Impact Test – Basic Simulation
Step 11 – Run the AUTODYN Simulation ...
Training Manual
11.c The Solver Output shows the run statistics. This problem will only take a few minutes to solve and should terminate due to the condition “wrapup time reached ”.
Workshop 1. Taylor Impact Test – Basic Simulation
Step 12 – Review the Results
Training Manual
12.a Select Energy Summary under Solution Information to view the global statistics. Note how the Kinetic Energy of the projectile is converted into Internal Energy during impact. Also, the Hourglass Energy is sufficiently small (less than 10% of the Internal Energy).
Internal Energy Kinetic Energy Plasticity develops
Hourglass Energy
Workshop 1. Taylor Impact Test – Basic Simulation
Step 12 – Review the Results ...
Training Manual
12.b Select Directional Deformation (Z Axis) and Show the Elements under True Scale . The maximum displacement (-0.0024 m) is in the negative Z direction, so it appears as a minimum value.
SC
Workshop 1. Taylor Impact Test – Basic Simulation
Step 12 – Review the Results ...
Training Manual
12.c Likewise, select Equivalent Plastic Strain. 12.d Animate the results by setting the controls as shown below and then pressing the Animation button. For transient dynamics, the default Distributed mode is often inadequate, as it just linearly interpolates between saved results and not enough data sets may have been saved for good interpolation. The Result Sets mode is usually best, as only actual saved data is used.
Pick these 2 first Then pick this
Plastic strain constant after rod rebound from plate.
