ANSI NEMA WC 51-2009 ICEA P-54-440-2009 Ampacities of Cables Installed in Cable Trays

AMPACITIES OF CABLES INSTALLED IN CABLE TRAYS

Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMA No reproduction or networking permitted without license from IHS

Licensee=M+W Group San Francisco CA/5976524002, User=Bonita, Glenn Not for Resale, 05/28/2013 20:56:58 MDT

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

ANSI/NEMA WC 51 ICEA P-54-440

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



Approved as an American National Standard ANSI Approval Date: April 23, 2009

ANSI/NEMA WC 51-2009 ICEA P-54-440-2009 Ampacities of Cables Installed in Cable Trays

Prepared by: Insulated Cable Engineers Association, Inc. P.O. Box 1568 Carrollton, Georgia 30112 Published by: National Electrical Manufacturers Association 1300 North 17th Street, Suite 1752 Rosslyn, Virginia 22209 www.nema.org

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

© Copyright 2009 by the Insulated Cable Engineers Association and the National Electrical Manufacturers Association. All rights including translation into other languages, reserved under Universal Copyright Convention, the Berne Convention for the protection of Literary and Artistic Works, and the International and Pan American Copyright Conventions.



NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. The National Electrical Manufacturers Association (NEMA) and the Insulated Cable Engineers Association (ICEA) standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together persons who have an interest in the topic covered by this publication. While NEMA and ICEA administers the process and establishes rules to promote fairness in the development of consensus, they do not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA and ICEA disclaims liability for personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA and ICEA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA and ICEA do not undertake to guarantee the performance of any individual manufacturer or seller’s products or services by virtue of this standard or guide. In publishing and making this document available, NEMA and ICEA are not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA and ICEA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA and ICEA have no power, nor do they undertake to police or enforce compliance with the contents of this document. NEMA and ICEA do not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health or safetyrelated information in this document shall not be attributable to NEMA and ICEA and is solely the responsibility of the certifier or maker of the statement.

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



ANSI/NEMA WC 51-2009/ICEA P-54-440-2009 Page i

CONTENTS

© 2009 by the National Electrical Manufacturers Association and the Insulated Cable Engineers Association. Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMA No reproduction or networking permitted without license from IHS


--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

Page

Foreword ....................................................................................................................................................... ii Scope ............................................................................................................................................................iii History .......................................................................................................................................................... iv Section 1 GENERAL INFORMATION ........................................................................................................ 1 1.1 Background ........................................................................................................................................ 1 1.2 References ......................................................................................................................................... 1 1.2.1 Normative References............................................................................................................. 1 1.2.2 Other References .................................................................................................................... 2 1.3 DEFINITIONS..................................................................................................................................... 2 Section 2 TABLE DEVELOPMENT PARAMETERS ................................................................................. 4 2.1 Parameters Used to Develop Tray Ampacity Tables ......................................................................... 4 2.1.1 Cable Operating Temperatures............................................................................................... 4 2.1.2 Allowable Heat Generation...................................................................................................... 4 2.1.3 Calculated Depth of Cables in Trays – Apparent Fill Depth.................................................... 5 2.1.4 Cable Diameters...................................................................................................................... 5 2.1.5 Conductor Resistance ............................................................................................................. 5 2.1.6 Calculated Free-Air Ampacity.................................................................................................. 5 2.1.7 Ampacity Values...................................................................................................................... 6 Section 3 AMPACITY ADJUSTMENT FACTORS ..................................................................................... 7 3.1 Correction Factor for Diameters of Cables......................................................................................... 7 3.2 Correction Factor for Temperatures ................................................................................................... 7 3.2.1 Ambient Temperature.............................................................................................................. 7 3.2.2 Conductor Temperature .......................................................................................................... 8 3.3 Correction Factor for Number of Conductors ..................................................................................... 8 3.4 Correction Factors for Tray Covers .................................................................................................... 9 3.5 Correction Factors for Load Diversity................................................................................................. 9 3.5.1 Determining the Loading Factor .............................................................................................. 9 3.5.2 Diversity Factors.................................................................................................................... 10 Section 4 EXAMPLES .............................................................................................................................. 11 4.1 Calculating Apparent Depth of Cable ............................................................................................... 11 4.2 Selecting Ampacity Values and Using Adjustment Factors ............................................................. 12 4.3 Calculating and Applying Diversity Factors...................................................................................... 13 4.4 Multiple Adjustment Factors ............................................................................................................. 13 4.5 Calculating Ampacities for Cables Not Covered by Tables.............................................................. 13 Section 5 TABLES.................................................................................................................................... 15 5.1 Index to Tables ................................................................................................................................. 15

ANSI/NEMA WC 51-2009/ICEA P-54-440-2009 Page ii

Foreword This Standards Publication for Ampacities of Cables Installed in Cable Trays (ICEA P-54-440, NEMA WC 51-2008) was developed by the Insulated Cable Engineers Association, Inc. (ICEA) and approved by the National Electrical Manufacturers Association (NEMA). It supersedes WC 51-2003. ICEA/NEMA standards are adopted in the public interest and are designed to eliminate misunderstanding between the manufacturer and the user and to assist the user in selecting and obtaining the proper product for his particular need. Existence of an ICEA/NEMA standard does not in any respect preclude the manufacture or use of products not conforming to the standard. The user of this Standard is cautioned to observe any health or safety regulations and rules relative to the manufacture and use of cable made in conformity with this Standard. Requests for interpretation of this Standard must be submitted in writing to: Insulated Cable Engineers Association, Inc., P.O. Box 1568, Carrollton, Georgia, 30112 An official written interpretation will be provided. The Association will welcome any suggestions on ways to improve this Standard.

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



ANSI/NEMA WC 51-2009/ICEA P-54-440-2009 Page iii

Scope This Standards Publication covers the ampacity ratings for 600-15,000 volt solid dielectric cables installed in cable trays. Ampacity ratings are tabulated for single conductor cables, triplexed assemblies of single conductor cables, and three-conductor cables incorporating an overall jacket. Ampacities have been tabulated for the cable constructions and the operating conditions normally encountered for tray applications. Correction factors to adjust the tabulated values to better reflect specific conditions are provided. These include adjustments to account for ambient and operating temperatures, cable construction, tray covers, and diversification of the cable loading. This standard is intended primarily for use by the utility industry. It is not intended for use where compliance with the National Electrical Code or other regulations is mandatory.

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



ANSI/NEMA WC 51-2009/ICEA P-54-440-2009 Page iv

History Ampacity tables for cables in trays were published in the Insulated Power Cable Engineers Association Publication No. P-33-440, April 2, 1959 (IPCEA is currently known as ICEA). It assumed a load diversity but did not specifically define the diversity. The demands of modern generating plants required a more precise definition of operating conditions for the determination of cable ampacities. Experimental work with various cables and the loading of trays by J. Stolpe1 and the theory developed by Stolpe, Underwriters Laboratories Inc., Lee,2 and ICEA Publication P-46-426, IEEE S-135 Power Cable Ampacities, 1962 Edition provided a more accurate means of calculating ampacities of cables in trays. A joint committee of IPCEA and IEEE Insulated Conductors Committee utilized this work in preparing the ampacity tables. They were published in the IPCEA/NEMA Standards Publication for Ampacities of Cables in Open-top Cable Trays, IPCEA Publication No. P-54-440, NEMA Standards Publication No. WC 51-1972. They superseded the factors in Table B for cables without maintained spacing in the IPCEA “Factors for Calculating Ampacities of Cables Installed in Ladder Supports, Trays and Troughs,” P-33440, April 2, 1959. Table A of that publication covering factors for cables with maintained spacing was not affected. The 1975 edition of the IPCEA/NEMA Standards Publication was expanded to cover 15 kV cables and includes a great many editorial corrections that clarify the 1972 document. The document was revised in April 1976 and again in August 1979. NEMA reaffirmed the document on November 20, 1980. In October 1984, a correction was made in the earlier Appendix D and was included in that edition. The members of IEEE-IPCEA Joint Committee at the time of the initial writing were: R. C. Waldron, Chairman, D. A. Costello, E. Finch, E. L. Kolmorgen, M. J. Koulopoulos, R. H. Lee, R. A. Peterson, D. A. Silver, and J. Stolpe The extended information contained in this revision was made possible through recent theoretical and experimental work by W. Z. Black and B. L. Harshe3,4. This edition has been expanded to include tray fill depths up to 4 inches and adjustment factors to account for tray covers and load diversity. In addition, the tables have been revised to reflect current cable design practices and conductor sizes through 2000 kcmil inclusive.

© 2009 by the National Electrical Manufacturers Association and the Insulated Cable Engineers Association.

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



ANSI/NEMA WC 51-2009/ICEA P-54-440-2009 Page 1

Section 1 GENERAL INFORMATION 1.1

BACKGROUND

Establishing the ampacity of cables installed in cable trays can become quite complex since a cable tray may contain hundreds of cables differing in size and loading. Methods to compute cable ratings under these operating conditions were developed first by J. Stolpe. This conservative technique assumes the cables are packed into the tray and are operating at maximum loading such that the heat generated can be assumed to be uniformly distributed throughout the total cable mass. This has been and continues to be the basis for the ampacity tables provided in this standard. More recently, B. L. Harshe and W. Z. Black have developed models that account for load diversity and the presence of tray covers in the determination of allowable cable ampacity. The validation of their models also included tests using cable fill depths up to 4 inches. In recognition of this work, the tables have been expanded to include fill depths of 3.5 inches and 4 inches and adjustment factors have been added for diversity loading and the use of tray covers. Sample ampacity calculations are provided to demonstrate the use of the tables and adjustment factors. 1.2

REFERENCES

The following publications are adopted in part, by reference in this standard, and are available from the organizations listed below. 1.2.1

Normative References

The following normative documents contain provisions, which through reference in this text, constitute provisions of this Standards publication. By reference herein, these publications are adopted in whole or in part as indicated, in this standard.

Global Engineering Documents 15 Inverness Way East Englewood, CO 80112 ANSI/NEMA WC70/ICEA S-95-658-2009

Standard for Nonshielded Power Cables Rated 2000 Volts or Less for the Distribution of Electrical Energy

ANSI/NEMA WC71/ICEA S-96-659-1999

Standard for Nonshielded Power Cables Rated 20015000 Volts for the Distribution of Electrical Energy

ANSI/NEMA WC74/ICEA S-93-639-2006

5-46 kV Shielded Power Cable for use in the Transmission & Distribution of Electrical Energy

ANSI/ICEA S-97-682-2007

Standard for Utility Shielded Power Cables Rated 5-46 kV for the Distribution of Electrical Energy


--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---




Institute of Electrical and Electronics Engineers (IEEE) 345 East 47th Street New York, New York 10017-2394 IEEE Standard 835-1994

IEEE Standard Power Cable Ampacity Tables

Bureau Central de la Commission Electrotechnique International 3. rue de Varenbre Geneve, Suisse www.iec.ch IEC Publication 60287-1-1 Ed. 2.0 b.2006

1.2.2

Electric cables - Calculation of the current rating - Part 11: Current rating equations (100 % load factor) and calculation of losses - General

Other References Institute of Electrical and Electronics Engineers (IEEE) 345 East 47th Street New York, New York 10017-2394

(1)

IEEE Transaction Paper 70 TP 557 PWR, Ampacity for Cables in Randomly Filled Trays, J. Stolpe, 1970 (2) IEEE Transaction Paper 71 TP 543 PWR, Ampacity for Multiconductor Cables in Trays, R. Lee, 1971 (3) IEEE Transactions on Power Delivery Vol. 9 No. 4, Oct. 1994, Ampacity of Cables in Single Open-Top Cable Trays, B. Harche & W. Black (4) IEEE Transactions on Power Delivery Vol. 12 No. 1, Jan. 1997, Ampacity of Cables in Single Covered Trays, B. Harche & W. Black (5) Rating of Electric Power Cable, George J. Anders, IEEE Order Number PC5647 ISBN 0-7803-1177-9 1.3

DEFINITIONS

allowable heat generation: The maximum allowable heat generation (watts/inch2/ft) for the cable mass per unit length of tray. Exceeding this value will cause the cables in the tray to exceed their operating temperature limits. apparent fill depth: The calculated depth of cable in the tray. This value is used to determine the allowable heat generation for given tray fill conditions. The value is calculated by dividing the total area occupied by the cables in the tray by the width of the tray. CAUTION: To account for the fact that cables will not pack into a solid mass, each cable in the tray is assumed to occupy a space defined by a square whose sides equal the cable diameter. cover factor: The ampacity of a cable installed in a covered tray divided by the ampacity of the same cable in the same tray without a cover. diversification factor: The ampacity of a cable installed in a tray containing unequally loaded cables divided by the ampacity of the same cable and tray where all cables are fully loaded. % tray fill: The combined circular cross sectional area of the cables installed in the tray divided by the total available cross sectional area of the tray (width X height) expressed as a percentage.

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---


© 2009 by the National Electrical Manufacturers Association and the Insulated Cable Engineers Association. Licensee=M+W Group San Francisco CA/5976524002, User=Bonita, Glenn Not for Resale, 05/28/2013 20:56:58 MDT


CAUTION: To determine the apparent fill depth (basis for calculations and tables) when given the % Tray Fill, the following equation must be used to account for the different methods used to determine the cross sectional area occupied by the cables. (Refer to Section 4.1 for an example) Apparent Fill Depth = (4/π) * % Tray Fill * Tray Depth

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---




Section 2 TABLE DEVELOPMENT PARAMETERS 2.1

PARAMETERS USED TO DEVELOP TRAY AMPACITY TABLES

The tabulated ampacities are based on the fundamental assumption that all cables are fully loaded and operating at 100% load factor. The cables are tightly packed in a 24-inch wide uncovered tray. Variable parameters and assumptions applied in the determination and tabulation of the tray ampacities are listed and discussed below. 2.1.1

Cable Operating Temperatures

The ampacities tabulated are based on a normal conductor operating temperature of 90ºC (194ºF) and an air ambient temperature of 40ºC (104ºF). When trays are stacked, the ambient air temperature of the upper trays will be higher depending on the amount of ventilation and the distance between the trays. The same is true in cable tunnels without forced ventilation. In these and similar situations the use of a higher ambient temperature shall be considered. A 50ºC (122ºF) ambient will frequently exist at the top of the tunnel. Where trays contain cables having different maximum operating temperatures, ampacities for the entire group shall be limited to the lowest temperature rating Correction factors for other operating and ambient conditions are provided for in Section 3. 2.1.2

Allowable Heat Generation

The maximum heat generation is determined by the method developed by Stolpe. The values calculated for the tabulated Apparent Fill Depths are shown below in Table 2-1. The parameters employed in this calculation are shown in Table 2-2.

Apparent Fill Depth

Allowable Heat Generation

(inches)

(watts/inches/feet)

1 1.5 2 2.5 3 3.5 4

5.93 3.56 2.43 1.78 1.38 1.1 0.9



--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

Table 2-1 ALLOWABLE HEAT GENERATION


Table 2-2 PARAMETERS USED FOR TABULATED AMPACITY Variable Tray Width Surface Emissivity of Cable Mass Convective Heat Transfer Coefficient Cable Mass Temperature Ambient Air Temperature Thermal Resistivity of Cable Mass

2.1.3

Value Units 24 inches 0.8 None 0.223 Watts / sqft / degreeC 90 degree C 40 degree C 400 Degree C - cm / watt

Calculated Depth of Cables in Trays – Apparent Fill Depth

The depth of cables in trays should be calculated as follows:

n1d1 + n2 d 2 + n3d 3 + ...nn d n w 2

Calculated Depth, inches =

2

2

2

where: d1 , d2 , ...dn = diameter of cables, inches. n1 , n2 , ...nn = number of cables of diameters d1 , d2 ,...dn , respectively. w = width of tray, inches.

2.1.4

Cable Diameters

The cable diameters were calculated using the nominal conductor diameters and wall thickness provided in the referenced ICEA cable standards. For cable diameters different than those shown in the tables, see paragraph 3.1. 2.1.5

Conductor Resistance

Conductor resistance values were obtained from the referenced ICEA standards and corrected for operating temperature and skin effect. The individual strands of copper conductors are coated. For triplexed assemblies and three conductor cables the resistance was further adjusted to account for 2% increase in length due to cabling. Proximity effects have been included and are based on a triangular configuration. Single conductors are assumed to lie in close triangular arrangements. 2.1.6

Calculated Free-Air Ampacity

The ampacity of cables in free-air is provided for reference. Values are based on computation methods described in IEEE Std 835 – 1994. Tabulated values in this standard are limited to 80% of the free-air ampacity based on natural convection and no solar heat absorption. The calculated conductor resistance at 90°C including skin and proximity effects and cable diameters used in the ampacity calculation are as shown in the tables. Thermal resistivity values for the internal cable components are 350°C-cm/watt and 500°C-cm/watt for the insulation and jacket, respectively.


--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---




2.1.7

Ampacity Values

Tabulated values were calculated using the following equation:

I = d×

Allowable Heat Generation n×Rc

where: I = ampacity, amperes d = cable diameter, inches Allowable Heat Generation from Table 2-1, (watts/inches/feet) n = number of cable conductors RC = conductor resistance, micro-ohms/ft --```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---




Section 3 AMPACITY ADJUSTMENT FACTORS 3.1

CORRECTION FACTOR FOR DIAMETERS OF CABLES

Diameters for cables meeting the construction requirements of the referenced ICEA standards are given in each table. For cable diameters different than the tabulated values, the ampacity can be calculated by direct proportion to the cable diameters as follows:

d I = x Io x d o where: Io = ampacity for cable diameter d0 from the table. do = cable diameter from the table. Ix = ampacity for cable diameter dx dx= cable diameter less than the calculated depth of those in tables. 3.2

CORRECTION FACTOR FOR TEMPERATURES

The tables are based on a conductor temperature of 90ºC and an ambient air temperature of 40ºC. 3.2.1

Ambient Temperature

If the trays are stacked, the ambient air temperature of the upper trays will be higher depending on the amount of ventilation around the trays. In cable tunnels without forced ventilation, a 50ºC ambient will frequently exist at the top of the tunnel. The following factors should be used for correcting for different ambient air temperatures.

Table 3-1 AMBIENT AIR ADJUSTMENT Ambient Air Temperature degrees C (degrees F)

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

30 (86) 35 (45) 40 (104) 45 (113) 50 (122) 55 (131)

Adjustment Factor 1.09 1.05 1.00 0.95 0.90 0.85




3.2.2

Conductor Temperature

The rating for normal conductor operating temperatures differing from 90ºC should be determined by the following multiplying factors: Table 3-2 CONDUCTOR TEMPERATURE ADJUSTMENT Conductor Temperature

Adjustment Factor 1.24 1.11 1.00 0.95 0.86 0.80 0.66

degrees C (degrees F)

125 (257) 105 (221) 90 (194) 85 (184) 75 (167) 70 (158) 60 (140)

Where trays contain cables having different maximum operating temperatures, ampacities for the entire group shall be limited to the lowest temperature rating. Where both the ambient temperature and conductor temperature differ from those stated in 2.1.1, the product of both correction factors should be used. 3.3

CORRECTION FACTOR FOR NUMBER OF CONDUCTORS

The tables apply to single conductor, triplexed and three-conductor cables. For other numbers of conductors, the current will vary as the square root of the conductors carrying current and the ampacity can be calculated as follows:

⎛ d 'x ⎞ 3 I ' x = I ' 0 ⎜⎜ ' ⎟⎟ ⎝ d 0 ⎠ nx where:

I ' 0 = ampacity for three-conductor cable from the table. I ' x = ampacity for cable having n x conductors. d ' x = diameter of cable having n x conductors. d ' 0 = diameter of three-conductor cable from the table. n x = number of conductors other than given in the table.

© 2009 by the National Electrical Manufacturers Association and the Insulated Cable Engineers Association. --```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---




3.4

CORRECTION FACTORS FOR TRAY COVERS

The following table provides ampacity correction factors for trays employing covers. The adjustment factors represent worst case conditions where the air gaps between the cable mass and cover are greater than ½ inch. For an air gap spacing less than ½ inch the thermal resistance of the air gap decreases dramatically resulting in an increase in the multiplier. Table 3-3 TRAY COVER ADJUSTMENT Apparent Fill Depth (inches)

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

1 1.5 2 2.5 3 3.5 4

3.5

Adjustment Factor 0.78 0.80 0.81 0.82 0.83 0.84 0.85

CORRECTION FACTORS FOR LOAD DIVERSITY

The thermal model used to compute tray ampacities of diversely loaded cables is based on the work of B.L. Harshe and W.Z. Black. Their “pancake” layer model assumes heavily loaded cables are located at the center (horizontal layer across the tray width) of the cable mass while lightly loaded cables are nearest the surface. This approach will lead to the maximum possible cable mass temperature and therefore a conservative ampacity but only when it can be safely assumed that the heat is generated uniformly across the tray width. Cable ampacity is calculated by multiplying the value tabulated by the ampacity correction factor provided in Table 3-4. CAUTION: In situations where heavily loaded cables are installed in a tray and the area occupied by these loaded cables cannot be safely assumed to extend across the tray width (i.e., loaded cables are bunched together) the correction factors given in Table 3-4 should not be utilized. These situations are beyond the scope of this standard. Methods are available to address these special cases. The user should refer to Section 1.2.2 for references that provide guidance. 3.5.1

Determining the Loading Factor

Cables operating at less than 25% of the tabulated ampacity shall be considered lightly loaded and will therefore have negligible effect on the temperature rise. Cables carrying load currents greater than 25% of the tabulated values shall be considered fully loaded. Load diversification is calculated by dividing the area occupied by the heavily loaded cables by the total area occupied by all cables in the tray.




3.5.2

Diversity Factors

Load Diversification %

10 or less 15 20 25 30 35 40 45 50

Adjustment Factor 2.70 2.26 1.97 1.76 1.61 1.50 1.42 1.35 1.30

Load Diversification %

55 60 65 70 75 80 85 90 95 or higher

Adjustment Factor 1.25 1.21 1.18 1.14 1.10 1.07 1.03 1.01 1.00



--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

Table 3-4 LOAD DIVERSIFICATION ADJUSTMENT


Section 4 EXAMPLES 4.1

CALCULATING APPARENT DEPTH OF CABLE

A 4-inch deep by 24-inch wide covered cable tray currently contains the following power and control cables that are used to energize two separate but identical loads.

Cable Type 3/c-4/0 AWG copper, 5kV nonshielded insulated nonjacketed conductors with overall jacket 3/c-1/0 AWG copper, 600 volt insulated nonjacketed conductors with overall jacket 3/c-No. 2 AWG copper, 600 volt insulated nonjacketed conductors with overall jacket 1/c-No. 8 AWG copper, 600 volt insulated & jacketed conductors 1/c-No. 12 AWG copper, 600 volt insulated conductors

Existing Quantity

Loading Level amps/cable conductor

3

165

4

75

4

12

20

5

40

1

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

The tray is currently estimated at 20% fill, but it is planned to double the plant capacity by adding two additional units and use the existing tray to route the new circuits to their intended locations. Can the tray be utilized without exceeding the 90°C rating of the cable products it contains? Ambient air temperature is near 40°C during summer months.




Cable Type

Proposed Quantity

3/c-4/0 AWG copper, 5kV nonshielded insulated nonjacketed conductors with overall jacket

6

Cable Information Table Number 5-17

Cable Diameter (inch) 1.75

Tray Area Occupied (square inch) 18.38

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

3/c-1/0 AWG copper, 600 volt 8 5-7 1.33 14.15 insulated jacketed conductors with overall jacket 3/c-No. 2 AWG copper, 600 volt 8 5-7 1.09 9.50 insulated jacketed conductors with overall jacket 1/c-No. 8 AWG copper, 600 volt 40 5-5 0.27 2.92 insulated & jacketed conductors 1/c-No. 12 AWG copper, 600 volt 80 5-2 0.18 2.59 insulated conductors Area Occupied by Cables [n1 d1 2 + n2 d 2 2 + n3 d 3 2 + ...nn d n 2 ] - square inches 47.54 Tray Width - inches 24 Apparent Depth of Cables - inches 1.98 Alternative Calculation (see definition of % fill) Existing % tray fill 20 Proposed % tray fill 40 Apparent Depth of Cables* – inches *See equation under cautionary note in paragraph 1.3 4.2

2.04

SELECTING AMPACITY VALUES AND USING ADJUSTMENT FACTORS

Using the identified tables the ampacity for each cable is obtained by reading down the column containing the calculated apparent fill depth until it intercepts the row containing the appropriate conductor size. Since the tables are for trays without covers, the ampacity needs to be adjusted accordingly. The effect of the cover is obtained from Table 3-3 in this case an adjustment multiplier of 0.81 (2 inch depth of fill) is to be used. The 80% In-Free Air ampacity is also available in the table for reference and it is recommended that the tray cable ampacity be limited to the smaller of these values. As such, for this example we obtain the following:

Cable Type

Tabulated Cable Adjustment for Ampacity Information Tray Cover Factor amps Table No. (Table 3-3) = 0.81

Free Air Ampacity amps

Load Requirements amps

3/c-4/0 AWG copper, 5kV nonshielded insulated nonjacketed conductors with overall jacket

191

5-17

155

258

165

3/c-1/0 AWG copper, 600 volt insulated nonjacketed conductors with overall jacket

103

5-4

83

160

75

3/c-No. 2 AWG copper, 600 volt insulated nonjacketed conductors with overall jacket

67

5-4

54

118

12

14

5-5

11

63

5

6

5-2

5

34

1

1/c-No. 8 AWG copper, 600 volt insulated & jacketed conductors 1/c-No. 12 AWG copper, 600 volt insulated conductors




Note that the 5kV cable ampacity after correcting for the presence of a tray cover is exceeded. One solution to the problem would be to remove the cover but we also know that the analysis assumes all the cables to be fully loaded and we know in this example that this is not the case. 4.3

CALCULATING AND APPLYING DIVERSITY FACTORS

A quick analysis of the diversity is in order and the results shown below provide confidence that the existing tray can be used for these new circuits.

Cable Type 3/c-4/0 AWG copper, 5kV nonshielded insulated nonjacketed conductors with overall jacket

Load Covered Loading Tray Area Heat Generation Requirement Tray Rating Level Occupied Area amps amps % of rated Square inch Square inch

165

154

107%

18.38

18.38

3/c-1/0 AWG copper, 600 volt insulated nonjacketed conductors with overall jacket

75

84

89%

14.15

14.15

3/c-No. 2 AWG copper, 600 volt insulated nonjacketed conductors with overall jacket

12

54

22%

9.50

0.00

1/c-No. 8 AWG copper, 600 volt insulated & jacketed conductors

5

9

56%

2.92

2.92

1/c-No. 12 AWG copper, 600 volt insulated conductors

1

5

21%

2.59

0.00

Load Diversification (= 35.44 / 47.54) Diversification Factor

47.54 35.44 0.75 1.1 (from Table 3-4)

The calculated diversity factor of 1.1 will yield an ampacity of 169 amps (154 x 1.1), which exceeds the required 165 amps. 4.4

MULTIPLE ADJUSTMENT FACTORS

The following scenario is based on the first example given in 4.2 to demonstrate multiple adjustment factors. Due to the addition of new process equipment, the ambient air temperature has increased 5°C to 45°C. In addition, concerns for cable damage resulting from internal construction activities have forced engineers to consider tray covers at least temporarily for a 2-inch filled cable tray. What effect will these actions have on the existing tray cable ratings? From Table 3-1 a factor of 0.95 must be applied to the tabulated ampacities to attain the ampacity rating at 45°C. From Table 3-3, the adjustment factor to compensate for tray covers will depend on the fill depth. This will range from 0.78 to 0.85. For a tray fill depth of 2 inches the adjustment factor is 0.81. For trays having a fill depth of 2 inches, the ampacity shown in the table corresponding to the cable type in the column for a 2-inch fill depth, should be multiplied by 0.77 (0.95 x 0.81), to attain the correct ampacity. 4.5

CALCULATING AMPACITIES FOR CABLES NOT COVERED BY TABLES

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

Calculating the ampacity of cables not specifically covered by the tables can be accomplished by using the tabulated ampacities for three conductor cables and adjusting for the actual number of conductors and cable diameter or by using the equation from which the tables were prepared directly. Consider the following problem.


© 2009 by the National Electrical Manufacturers Association and the Insulated Cable Engineers Association. Licensee=M+W Group San Francisco CA/5976524002, User=Bonita, Glenn Not for Resale, 05/28/2013 20:56:58 MDT


What is the ampacity of a 7/C No. 12 AWG 600 volt cable installed in a 24-inch wide tray to a 1.5-inch fill depth? The cable is constructed of insulated copper single conductors and an overall jacket with a 0.60inch cable diameter. Starting with Table 5-1, the ampacity of a 3/C cable of similar construction can be obtained from ampacity Table 5-4. A 3/C cable with an overall diameter of 0.42” has an ampacity of 10 amps for 1.5” fill. For a 7/C cable, this ampacity has to be corrected for both the number of conductors and the difference in cable diameter. To make this correction, the equation from Section 3.3 is used:

I

'

x

=I

'

d 'x 0

I x' = 10 ×

d

'

0

3 nx

0.60 3 × 0.42 7

I x' = 10 × 1.43 × 0.655 I x' = 9 amps If the tray is covered, an additional derating is required. For a 1.5-inch fill depth the adjustment factor from Table 3-3 is 0.80; therefore,

I x' = 9 amps × 0.80 = 7 amps


--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---




Section 5 TABLES 5.1

INDEX TO TABLES Table 5-1 REFERENCE TABLES FOR SPECIFIC CABLE CONSTRUCTIONS Voltage Class

Cable Description Number Insulated Conductors Conductors Jacketed Shielded

Overall Jackets

Table Number Conductor Copper Alum

1

no

no

no

5-2

5-2A

3

no

no

no

5-3

5-3A

3

no

no

yes

5-4

5-4A

1

yes

no

no

5-5

5-5A

3

yes

no

no

5-6

5-6A

3

yes

no

yes

5-7

5-7A

1

no

no

no

5-8

5-8A

3

no

no

no

5-9

5-9A

3

no

no

yes

5-10

5-10A

1

yes

no

no

5-11

5-11A

3

yes

no

no

5-12

5-12A

3

yes

no

yes

5-13

5-13A

1

yes

no

no

5-14

5-14A

3

yes

no

no

5-15

5-15A

100%

3

yes

no

yes

5-16

5-16A

Insulation

3

no

no

yes

5-17

5-17A

Level

1

yes

yes

no

5-18

5-18A

3

yes

yes

no

5-19

5-19A

3

no

yes

yes

5-20

5-20A

15000

1

yes

yes

no

5-21

5-21A

100% Ins.

3

yes

yes

no

5-22

5-22A

Level

3

no

yes

yes

5-23

5-23A

600

2000

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

5000



Ampacities of 600 Volt Copper Cables

ANSI/NEMA WC 51-2009/ ICEA P-54-440-2009 Page 16

Conductor Size awg or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

ICEA P-54-440/NEMA WC 51-2008 Page 16

Table 5-2 1/C Insulated Non-Jacketed Cables Cable Diameter Inches 0.16 0.18 0.21 0.22 0.27 0.30 0.35 0.41 0.49 0.53 0.58 0.63 0.69 0.77 0.87 1.00 1.22 1.37 1.54 1.66 1.78 1.88

Conductor Resistance micro-ohms/ft 3413.04 2148.18 1350.11 1071.63 849.64 534.59 336.07 211.38 167.61 133.27 105.74 84.18 66.33 56.70 41.13 29.27 20.67 16.72 14.35 12.92 11.89 11.11

80% of Indoor Ampacity Amperes 26 34 46 53 64 85 114 154 184 214 250 291 342 383 476 602 774 906 1022 1113 1198 1272

Calculated Depth of Cables in 24" Wide Tray, Inches 1

1.5

7 9 14 16 23 32 46 69 92 112 137 167 206 249 330 450 653 816 990 1125 1257 1373

5 7 11 13 17 24 36 53 71 87 106 130 160 193 256 349 506 632 767 871 974 1064

2 2.5 3 Ampacity, Amperes 4 4 3 6 5 5 9 8 7 10 9 8 14 12 11 20 17 15 30 25 22 44 38 33 59 50 44 72 61 54 88 75 66 107 92 81 132 113 100 159 136 120 211 181 159 288 247 217 418 358 315 522 447 394 634 542 478 720 616 543 805 689 606 879 753 663

3.5

4

3 4 6 7 10 14 20 30 40 48 59 72 89 107 142 194 281 351 426 484 541 592

3 4 5 6 9 12 18 27 36 44 54 65 80 97 129 175 255 318 386 438 490 535

Table 5-3 3-1/c Insulated Non-Jacketed Cables Triplexed Conductor Size awg or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter Inches 0.34 0.39 0.45 0.47 0.58 0.65 0.75 0.88 1.06 1.14 1.25 1.36 1.49 1.66 1.88 2.16 2.63 2.95 3.32 3.58 3.84 4.05




1.5

8 12 17 20 28 39 57 84 114 137 169 206 255 307 408 556 805 1004 1220 1386 1550 1692

6 9 13 15 21 30 44 65 88 107 131 160 197 238 316 431 624 778 945 1074 1201 1311


3.5

4

3 5 7 9 12 17 25 36 49 59 73 89 110 132 176 239 347 432 525 597 668 729

3 5 7 8 11 15 22 33 44 54 66 80 99 120 159 217 314 391 475 540 604 659

Table 5-4 3/c Insulated Non-Jacketed conductors with overall jacket Conductor Size awg or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000





1.5

9 13 18 21 30 43 62 94 119 145 176 213 250 278 342 426 535 618 685 742 792 842

7 10 14 16 23 33 48 73 92 112 136 165 203 248 329 426 535 618 685 742 792 842


3.5

4

4 5 8 9 13 18 26 40 51 62 76 92 113 138 183 246 350 442 532 604 670 738

4 5 7 8 12 17 24 37 46 56 68 83 102 125 165 223 317 400 481 546 606 667

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---


© 2009 by the National Electrical Manufacturers Association Licensee=M+W Group San Francisco CA/5976524002, User=Bonita, Glenn and the Insulated CableNotEngineers Association. for Resale, 05/28/2013 20:56:58 MDT

ANSI/NEMA ICEA P-54-440 / NEMAWC WC51-2009/ 51-2008 Page 17 ICEA P-54-440-2009

Ampacities of 600 Volt Aluminum Cables Table 5-2a 1/C Insulated Non-Jacketed Cables Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000



80% of Indoor Ampacity

micro-ohms/ft

Amperes

5410.11 3405.14 2140.09 1698.67 1346.79 847.40 532.71 335.08 265.69 210.57 167.06 132.99 105.46 89.25 64.25 45.53 31.05 24.19 20.12 17.56 15.81 14.57

20 27 37 42 50 67 90 123 146 170 199 232 271 306 381 482 631 754 863 954 1038 1110

Page 17

Calculated Depth of Cables in Tray, Inches 1

1.5

5 8 11 13 18 25 37 55 73 89 109 133 164 198 264 361 533 678 836 954 1038 1110

4 6 9 10 14 19 29 42 57 69 85 103 127 154 205 280 413 526 648 747 845 929

2

2.5

3

Ampacity, Amperes 3 3 3 5 4 4 7 6 5 8 7 6 11 10 9 16 14 12 24 20 18 35 30 26 47 40 35 57 49 43 70 60 53 85 73 64 105 90 79 127 109 96 169 145 128 231 198 174 341 292 257 434 372 327 535 458 403 618 529 465 698 597 526 768 657 579

3.5

4

2 3 5 6 8 11 16 23 32 38 47 57 70 85 114 155 230 292 360 415 470 517

2 3 4 5 7 10 14 21 29 35 43 52 64 77 103 141 208 264 326 376 425 467

Table 5-3a 3-1/C Insulated Non-Jacketed Cables Triplexed Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000




micro-ohms/ft

Amperes

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.65 107.57 91.04 65.53 46.44 31.68 24.68 20.52 17.91 16.13 14.86

16 22 29 34 40 54 72 98 117 136 159 186 217 245 306 387 507 606 694 767 836 894

Calculated Depth of Cables in Tray, Inches 1 6 9 14 16 22 31 45 67 91 109 135 164 202 245 306 387 507 606 694 767 836 894

1.5 5 7 10 12 17 24 35 52 70 85 104 127 156 190 253 345 507 606 694 767 836 894

2

2.5

3


3.5

4

3 4 6 7 9 13 19 29 39 47 58 71 87 105 141 192 283 360 444 512 579 636

3 4 5 6 9 12 18 26 35 43 52 64 79 95 127 174 256 325 401 463 524 575

Table 5-4a 3/C Insulated Non-Jacketed Conductors with Overall Jacket Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000




micro-ohms/ft

Amperes

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 136.25 108.05 91.44 66.38 47.59 33.17 26.62 22.81 20.42 18.85 17.69

16 21 28 32 39 52 70 94 110 127 148 171 199 222 274 342 437 510 570 619 659 694


1.5 6 8 11 13 19 26 38 58 73 89 108 132 161 198 263 342 437 510 570 619 659 694

2

2.5

3


3.5

4

3 4 6 7 10 15 21 32 41 50 60 73 90 110 146 197 286 365 442 504 558 609

3 4 6 7 9 13 19 29 37 45 55 66 81 100 132 179 259 330 400 456 505 551

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



ANSI/NEMA WC 51-2009/ ICEA P-54-440-2009

Table 5-5 1/C Insulated Jacketed Cables

Page 18 Conductor Size AWG

or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

ICEA P-54-440 / NEMA WC 51-2008 Page 18


Cable Diameter



Inches

micro-ohms/ft

Amperes

0.16 0.18 0.21 0.22 0.27 0.33 0.38 0.44 0.53 0.57 0.62 0.67 0.73 0.84 0.94 1.07 1.29 1.44 1.62 1.80 1.92 2.02

3413.04 2148.18 1350.11 1071.63 849.64 534.59 336.07 211.38 167.61 133.23 105.71 84.13 66.27 56.63 41.01 29.12 20.50 16.51 14.12 12.51 11.49 10.70

26 34 46 53 63 86 115 155 184 214 249 290 339 378 469 591 760 893 1005 1090 1171 1244


1.5

2

2.5

3

3.5

4

3 5 7 8 11 17 24 36 48 58 71 86 105 131 172 233 335 416 506 598 665 725

3 4 6 7 10 15 22 32 43 52 63 77 94 117 154 208 299 372 452 534 594 648

3 4 5 6 9 14 20 29 39 47 57 69 85 106 139 188 270 336 409 483 537 586

Ampacity, Amperes

7 9 14 16 23 35 50 74 100 120 147 178 218 272 357 483 694 863 1005 1090 1171 1244

5 7 11 13 17 27 39 57 77 93 114 138 169 211 277 374 538 669 813 960 1069 1165

4 6 9 10 14 22 32 47 64 77 94 114 140 174 229 309 444 552 672 793 883 963

4 5 8 9 12 19 28 40 55 66 80 97 120 149 196 265 380 473 575 679 756 824

Table 5-6 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG

or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000




micro-ohms/ft

Amperes

3481.30 2191.14 1377.11 1093.06 866.63 545.28 342.79 215.61 170.96 135.89 107.82 85.81 67.59 57.76 41.83 29.70 20.91 16.85 14.40 12.76 11.72 10.91

20 27 36 42 50 68 92 124 147 171 200 232 272 306 378 477 614 721 813 884 950 1008


1.5 6 9 13 15 21 30 44 65 88 107 131 160 197 238 317 432 614 721 813 884 950 1008

2

2.5

3


3.5

4

3 5 7 9 12 17 25 36 49 59 73 89 110 132 176 240 348 435 530 607 679 742

3 5 7 8 11 15 22 33 44 54 66 80 99 120 159 217 315 394 479 549 614 672

Table 5-7 3/C Insulated Jacketed Conductors with Overall Jacket

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000


Cable Diameter



Inches

micro-ohms/ft

Amperes

0.44 0.48 0.56 0.59 0.69 0.82 0.96 1.09 1.24 1.33 1.43 1.54 1.72 1.96 2.18 2.47 2.99 3.32 3.71 4.10 4.35 4.57

3481.30 2191.14 1377.11 1093.06 866.63 545.28 342.79 215.61 170.96 136.27 108.12 86.26 68.10 58.22 42.53 30.57 22.03 18.08 15.71 14.10 12.92 11.93

22 28 38 44 51 70 94 125 146 168 195 225 262 296 362 448 558 642 709 774 826 876


1.5 8 11 16 19 26 38 56 81 103 124 150 181 227 280 362 448 558 642 709 774 826 876

2

2.5

3


3.5

4

5 6 9 11 14 21 31 45 57 69 83 100 126 156 202 271 386 473 567 661 733 801

4 6 8 10 13 19 28 41 52 62 75 91 114 141 183 245 349 428 513 598 663 725


ANSI/NEMA WCWC 51-2009/ ICEA P-54-440 / NEMA 51-2008 Page 19 ICEA P-54-440-2009

Ampacities of 600 Volt Aluminum Cables Table 5-5a 1/C Insulated Jacketed Cables Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.16 0.18 0.21 0.22 0.27 0.33 0.38 0.44 0.53 0.57 0.62 0.67 0.73 0.84 0.94 1.07 1.29 1.44 1.62 1.80 1.92 2.02

5410.11 3405.14 2140.09 1698.67 1346.79 847.40 532.71 335.08 265.69 210.57 167.06 132.95 105.43 89.22 64.17 45.42 30.94 24.05 19.95 17.24 15.48 14.21

20 27 37 42 50 68 91 123 146 170 198 230 269 302 374 474 618 740 846 929 1009 1079

Page 19


1.5 4 6 9 10 14 21 31 45 61 74 91 110 134 168 221 300 438 554 684 818 921 1011

2

2.5

3


3.5

4

2 3 5 6 8 12 17 25 34 41 50 61 75 93 123 167 243 308 380 455 512 562

2 3 4 5 7 11 16 23 31 37 46 55 67 84 111 151 220 279 344 411 463 508

Table 5-6a 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.34 0.39 0.45 0.47 0.58 0.71 0.82 0.95 1.14 1.23 1.34 1.44 1.57 1.81 2.03 2.31 2.78 3.10 3.49 3.88 4.14 4.36

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.61 107.54 91.00 65.45 46.33 31.56 24.53 20.34 17.58 15.79 14.49

16 22 29 33 40 54 73 98 118 136 159 185 216 243 302 382 499 598 683 753 818 875


1.5 5 7 10 12 17 26 38 56 75 91 112 135 165 207 273 370 499 598 683 753 818 875

2

2.5

3


3.5

4

3 4 6 7 9 15 21 31 42 51 62 75 92 115 152 206 300 379 469 560 631 694

3 4 5 6 9 13 19 28 38 46 56 68 83 104 137 186 271 343 424 507 571 627

Table 5-7a 3/C Insulated Jacketed Conductors with Overall Jacket Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000 Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMA No reproduction or networking permitted without license from IHS

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.44 0.48 0.56 0.59 0.69 0.82 0.96 1.09 1.24 1.33 1.43 1.54 1.72 1.96 2.18 2.47 2.99 3.32 3.71 4.10 4.35 4.57

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 136.21 108.02 91.41 66.31 47.51 33.08 26.50 22.67 20.18 18.59 17.42

17 22 30 34 41 55 74 99 116 134 155 179 209 236 290 359 456 530 590 647 689 725


1.5

2

2.5

3

Ampacity, Amperes 6 5 5 4 9 7 6 6 13 11 9 8 15 13 11 10 20 17 14 13 30 25 21 19 45 37 32 28 64 53 45 40 82 68 58 51 99 82 70 62 119 99 84 74 144 119 102 89 180 149 127 112 223 185 158 139 290 241 206 182 359 323 276 243 456 456 400 353 530 530 497 437 590 590 590 528 647 647 647 619 689 689 689 --```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`--- 684 725 725 725 725

3.5

4

4 5 7 9 11 17 25 36 46 55 66 80 100 124 162 217 315 391 472 553 611 663

3 4 7 8 10 15 23 32 41 50 60 72 91 112 147 196 285 353 427 500 553 600



Table 5-8 1/C Insulated Non-Jacketed Cables

Page 20 Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000



Cable Diameter



Inches

micro-ohms/ft

Amperes

0.19 0.21 0.24 0.25 0.29 0.32 0.37 0.43 0.51 0.55 0.60 0.65 0.71 0.78 0.88 1.01 1.24 1.39 1.57 1.69 1.81 1.91

3413.04 2148.18 1350.11 1071.63 849.64 534.59 336.07 211.38 167.61 133.25 105.73 84.15 66.30 56.69 41.11 29.25 20.62 16.66 14.26 12.82 11.80 11.01

27 36 48 54 65 86 116 156 186 215 251 293 343 384 476 602 774 906 1021 1114 1198 1272


1.5 6 9 12 14 19 26 38 56 74 90 110 134 165 195 259 352 515 643 784 891 994 1086

2

2.5

3


3.5

4

3 5 7 8 10 15 21 31 41 50 61 74 91 109 144 196 286 357 436 495 553 604

3 4 6 7 9 13 19 28 37 45 55 67 83 98 130 177 259 323 394 448 500 546

Table 5-9 3-1/C Insulated Non-Jacketed Cables Triplexed Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.41 0.45 0.52 0.54 0.63 0.69 0.80 0.93 1.10 1.19 1.29 1.40 1.53 1.68 1.90 2.18 2.67 3.00 3.38 3.64 3.90 4.12

3481.30 2191.14 1377.11 1093.06 866.63 545.28 342.79 215.61 170.96 135.91 107.84 85.83 67.62 57.82 41.93 29.83 21.03 16.99 14.54 13.08 12.03 11.23

22 29 38 44 52 69 93 125 149 173 202 234 274 308 382 483 622 730 822 897 965 1026


1.5 8 10 15 18 23 32 47 69 92 111 135 165 203 241 320 435 622 730 822 897 965 1026

2

2.5

3


3.5

4

4 6 8 10 13 18 26 38 51 62 75 92 113 134 178 242 353 441 537 609 681 744

4 5 8 9 12 16 24 35 46 56 68 83 102 121 161 219 319 399 486 551 616 673

Table 5-10 3/C Insulated Non-Jacketed Conductors with Overall Jacket Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.44 0.48 0.56 0.59 0.67 0.75 0.90 1.03 1.16 1.24 1.34 1.45 1.58 1.78 2.01 2.30 2.82 3.15 3.55 3.82 4.07 4.29

3481.30 2191.14 1377.11 1093.06 866.63 545.28 342.79 215.61 170.96 136.29 108.13 86.27 68.12 58.25 42.57 30.62 22.10 18.15 15.77 14.21 13.03 12.04

21 27 36 42 49 65 87 117 136 157 182 211 246 273 335 418 520 599 666 722 772 819


1.5 8 11 16 19 25 35 53 76 97 116 140 170 209 254 335 418 520 599 666 722 772 819

2

2.5

3


3.5

4

5 6 9 11 14 19 29 42 54 64 78 95 116 141 187 252 363 448 541 614 683 749

4 6 8 10 12 18 27 38 49 58 71 86 105 128 169 228 329 405 490 555 618 677

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



ICEA P-54-440 / NEMAWC WC51-2009/ 51-2008 ANSI/NEMA Page 21 ICEA P-54-440-2009

Ampacities of 2000 Volt Aluminum Cables Table 5-8a 1/C Insulated Non-Jacketed Cables Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.19 0.21 0.24 0.25 0.29 0.32 0.37 0.43 0.51 0.55 0.60 0.65 0.71 0.78 0.88 1.01 1.24 1.39 1.57 1.69 1.81 1.91

5410.11 3405.14 2140.09 1698.67 1346.79 847.40 532.71 335.08 265.69 210.57 167.06 132.97 105.45 89.25 64.24 45.51 31.02 24.15 20.05 17.48 15.73 14.48

22 28 38 43 51 68 92 124 147 171 200 233 272 306 381 482 631 753 861 954 1038 1109

Page 21


1.5 5 7 10 11 15 21 30 44 59 72 88 106 130 156 207 282 420 534 662 763 861 947

2

2.5

3


3.5

4

3 4 5 6 8 12 17 25 33 40 49 59 73 87 115 157 234 297 368 424 479 526

2 3 5 6 7 10 15 22 30 36 44 53 66 78 104 142 211 268 333 383 433 476

Table 5-9a 3-1/C Insulated Non-Jacketed Cables Triplexed

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---


Cable Diameter



Inches

micro-ohms/ft

Amperes

0.41 0.45 0.52 0.54 0.63 0.69 0.80 0.93 1.10 1.19 1.29 1.40 1.53 1.68 1.90 2.18 2.67 3.00 3.38 3.64 3.90 4.12

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.62 107.56 91.03 65.52 46.42 31.64 24.63 20.45 17.83 16.05 14.77

17 22 30 34 42 54 74 99 118 138 160 186 218 246 306 387 507 606 693 768 835 894


1.5 6 8 12 14 19 26 37 55 73 88 108 131 161 192 256 349 507 606 693 768 835 894

2

2.5

3


3.5

4

3 5 7 8 10 14 21 30 40 49 60 73 89 107 142 194 287 366 453 522 589 649

3 4 6 7 9 13 19 28 37 44 54 66 81 96 129 175 260 331 409 472 533 587

Table 5-10a 3/C Insulated Non-Jacketed Conductors with Overall Jacket Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000


Cable Diameter



Inches

micro-ohms/ft

Amperes

0.44 0.48 0.56 0.59 0.67 0.75 0.90 1.03 1.16 1.24 1.34 1.45 1.58 1.78 2.01 2.30 2.82 3.15 3.55 3.82 4.07 4.29

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.98 107.82 91.26 65.97 46.99 32.37 25.52 21.49 18.91 17.16 15.85

17 22 29 33 39 51 70 93 108 125 145 168 195 218 270 338 430 506 571 626 673 714


1.5 6 9 13 15 20 28 42 61 77 92 112 135 166 203 270 338 430 506 571 626 673 714

2

2.5

3


3.5

4

4 5 7 9 11 15 23 34 43 51 62 75 92 113 150 203 300 378 464 532 595 652

3 4 7 8 10 14 21 31 39 46 56 68 83 102 136 184 271 342 419 481 538 590



Table 5-11 1/C Insulated Jacketed Cables

Page 22 Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000



Cable Diameter



Inches

micro-ohms/ft

Amperes

0.19 0.21 0.24 0.25 0.32 0.35 0.40 0.46 0.55 0.59 0.64 0.69 0.75 0.86 0.96 1.09 1.31 1.46 1.71 1.83 1.95 2.05

3413.04 2148.18 1350.11 1071.63 849.64 534.59 336.07 211.38 167.61 133.21 105.70 84.10 66.24 56.61 40.98 29.08 20.45 16.46 13.89 12.44 11.41 10.63

26 35 47 54 66 86 116 157 185 214 250 290 341 379 470 592 762 892 998 1090 1174 1246


1.5 6 9 12 14 21 29 41 60 80 96 117 142 174 216 283 381 547 679 866 979 1089 1186

2

2.5

3


3.5

4

3 5 7 8 12 16 23 33 45 54 65 79 97 120 157 212 304 377 481 544 605 659

3 4 6 7 10 14 21 30 40 48 59 71 87 108 142 192 275 341 435 492 548 596

Table 5-12 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.41 0.45 0.52 0.54 0.69 0.75 0.86 0.99 1.19 1.27 1.38 1.49 1.62 1.85 2.07 2.35 2.82 3.15 3.69 3.95 4.20 4.42

3481.30 2191.14 1377.11 1093.06 866.63 545.28 342.79 215.61 170.96 135.87 107.81 85.79 67.57 57.75 41.80 29.67 20.86 16.79 14.17 12.69 11.64 10.84

22 28 38 43 53 70 94 126 149 173 202 234 274 306 380 478 615 722 810 886 951 1010


1.5 8 10 15 18 26 35 51 73 99 119 145 175 215 265 349 470 615 722 810 886 951 1010

2

2.5

3


3.5

4

4 6 8 10 14 19 28 41 55 66 80 97 119 147 194 261 374 466 594 671 745 813

4 5 8 9 13 18 25 37 50 60 73 88 108 133 175 236 338 421 537 607 674 735

Table 5-13 3/C Insulated Jacketed Conductors with Overall Jacket Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.51 0.58 0.63 0.66 0.78 0.90 1.01 1.13 1.29 1.37 1.47 1.58 1.77 2.00 2.23 2.51 3.04 3.37 3.90 4.17 4.41 4.64

3481.30 2191.14 1377.11 1093.06 866.63 545.28 342.79 215.61 170.96 136.27 108.12 86.25 68.09 58.21 42.52 30.55 22.02 18.06 15.64 14.07 12.90 11.91

22 29 38 44 52 69 92 122 144 166 191 221 256 288 353 437 542 623 697 754 804 854


1.5 9 13 18 22 29 42 59 84 107 128 154 185 234 286 353 437 542 623 697 754 804 854

2

2.5

3


3.5

4

5 8 10 12 16 23 33 47 60 71 86 103 130 159 207 275 392 480 597 673 743 814

5 7 9 11 15 21 30 42 54 64 77 93 117 144 187 249 355 434 540 609 673 736

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



ICEA P-54-440 / NEMAWC WC51-2009/ 51-2008 ANSI/NEMA Page 23 ICEA P-54-440-2009

Ampacities of 2000 Volt Aluminum Cables Table 5-11a 1/C Insulated Jacketed Cables Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.19 0.21 0.24 0.25 0.32 0.35 0.40 0.46 0.55 0.59 0.64 0.69 0.75 0.86 0.96 1.09 1.31 1.46 1.71 1.83 1.95 2.05

5410.11 3405.14 2140.09 1698.67 1346.79 847.40 532.71 335.08 265.69 210.57 167.06 132.93 105.42 89.21 64.15 45.40 30.91 24.01 19.78 17.18 15.41 14.14

22 28 38 43 52 69 92 124 146 170 198 231 270 302 376 474 619 738 836 928 1010 1081

Page 23


1.5 5 7 10 11 16 23 33 47 64 77 93 113 138 172 226 305 445 562 725 833 937 1029

2

2.5

3


3.5

4

3 4 5 6 9 13 18 26 35 43 52 63 77 95 126 170 247 313 403 463 521 572

2 3 5 6 8 11 16 24 32 39 47 57 69 86 114 153 224 283 365 419 471 517

Table 5-12a 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG or kcmil 14 12 10 9 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.41 0.45 0.52 0.54 0.69 0.75 0.86 0.99 1.19 1.27 1.38 1.49 1.62 1.85 2.07 2.35 2.82 3.15 3.69 3.95 4.20 4.42

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.59 107.53 90.99 65.43 46.31 31.53 24.49 20.17 17.53 15.72 14.43

17 22 30 34 42 55 74 100 118 137 160 186 217 244 303 382 501 598 678 753 818 876


1.5 6 8 12 14 20 28 40 58 79 94 115 139 170 211 279 376 501 598 678 753 818 876

2

2.5

3


3.5

4

3 5 7 8 11 15 22 32 44 52 64 77 95 117 155 209 304 385 498 571 641 705

3 4 6 7 10 14 20 29 40 47 58 70 86 106 140 189 275 349 450 517 580 637

Table 5-13a 3/C Insulated Jacketed Conductors with Overall Jacket

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



Cable Diameter



Inches

micro-ohms/ft

Amperes

0.51 0.58 0.63 0.66 0.78 0.90 1.01 1.13 1.29 1.37 1.47 1.58 1.77 2.00 2.23 2.51 3.04 3.37 3.90 4.17 4.41 4.64

5518.31 3473.24 2182.89 1732.64 1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.95 107.81 91.24 65.93 46.94 32.32 25.45 21.39 18.80 17.05 15.73

18 23 30 35 42 55 73 97 114 132 152 176 203 230 283 353 447 525 596 652 699 742


1.5

10 14 19 22 30 43 61 86 110 131 152 176 203 230 283 353 447 525 596 652 699 742

7 11 15 17 23 33 47 67 85 102 123 148 186 228 283 353 447 525 596 652 699 742

3 2.5 Ampacity, Amperes 6 5 5 9 8 7 12 10 9 14 12 11 19 16 14 28 24 21 39 33 29 55 47 41 71 60 53 84 72 63 101 87 76 122 104 92 153 131 116 188 161 142 247 212 186 330 282 248 447 412 363 525 515 453 596 596 572 652 652 652 699 699 699 742 742 742 2

3.5

4

4 6 8 10 13 19 26 37 47 57 68 82 103 127 166 222 324 405 511 582 647 708

4 5 7 9 12 17 24 33 43 51 62 74 93 115 150 201 293 366 462 527 585 641




Ampacities of 5000 Volt Non-shielded Copper Cables Table 5-14 1/C Insulated Jacketed Cables

Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.56 0.59 0.64 0.70 0.74 0.78 0.83 0.91 0.97 1.08 1.18 1.34 1.56 1.71 1.91 2.03 2.18 2.28

849.64 534.59 336.07 211.38 167.61 133.11 105.61 83.95 66.06 56.49 40.77 28.76 20.04 15.95 13.51 12.03 10.94 10.15

89 117 155 206 238 275 319 368 428 475 585 735 938 1101 1236 1351 1448 1538

Calculated Depth of Cables in Tray, Inches 1 47 62 85 117 139 165 197 242 291 350 450 608 849 1043 1236 1351 1448 1538

1.5 36 48 66 91 108 128 152 187 225 271 349 471 658 808 980 1104 1244 1350

2

2.5

Ampacity, Amperes 30 26 40 34 54 47 75 64 89 76 105 90 126 108 155 133 186 159 224 192 288 247 390 333 543 465 667 571 810 693 912 781 1027 879 1116 955

3

3.5

4

23 30 41 57 67 79 95 117 140 169 217 294 409 503 610 688 774 841

20 27 37 50 60 71 85 104 125 151 194 262 365 449 545 614 691 751

18 24 33 46 54 64 77 94 113 136 175 237 331 406 493 555 625 679

Table 5-15 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.21 1.27 1.38 1.51 1.60 1.68 1.79 1.96 2.09 2.33 2.54 2.89 3.36 3.69 4.12 4.38 4.70 4.92

866.63 545.28 342.79 215.61 170.96 135.77 107.73 85.63 67.39 57.62 41.58 29.33 20.44 16.27 13.78 12.27 11.16 10.35

59 77 102 135 156 179 208 241 280 311 383 482 614 720 809 884 948 1006


1.5 45 59 81 112 133 157 188 231 277 311 383 482 614 720 809 884 948 1006

2

2.5


3

3.5

4

28 37 51 70 83 98 117 144 173 208 267 362 504 620 753 848 948 1006

25 33 45 62 74 87 104 128 154 186 239 323 450 554 672 757 852 926

23 30 41 56 67 79 94 116 139 168 216 292 407 501 608 685 771 838

Table 5-16 3/C Insulated Jacketed Conductors with Overall Jacket Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.12 1.23 1.33 1.46 1.54 1.63 1.79 1.99 2.11 2.28 2.51 2.92 3.32 3.65 4.14 4.40 4.65 4.88

866.63 545.28 342.79 215.61 170.96 136.23 108.09 86.20 68.03 58.18 42.46 30.47 21.93 17.96 15.56 13.99 12.82 11.83

54 72 94 124 143 164 190 221 255 281 342 424 526 604 671 726 770 818



1.5 41 57 78 108 128 152 188 221 255 281 342 424 526 604 671 726 770 818

2

2.5


3

3.5

4

26 36 49 67 80 95 117 145 174 203 261 359 481 584 671 726 770 818

23 32 43 60 71 85 104 130 155 181 233 320 429 522 636 712 770 818

21 29 39 54 65 76 94 117 140 164 211 290 388 472 575 644 711 777


--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

Page 24

Ampacities of 5000 Volt Nonshielded Aluminum Cables

ICEA P-54-440 / NEMA 51-2008 ANSI/NEMA WCWC 51-2009/ Page 25 ICEA P-54-440-2009

Page 25

Table 5-14a 1/C Insulated Jacketed Cables Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.56 0.59 0.64 0.70 0.74 0.78 0.83 0.91 0.97 1.08 1.18 1.34 1.56 1.71 1.91 2.03 2.18 2.28

1346.79 847.40 532.71 335.08 265.69 210.57 167.06 132.81 105.32 89.14 64.00 45.17 30.64 23.65 19.49 16.86 15.02 13.73

71 93 123 163 189 218 253 292 339 378 467 587 759 904 1029 1141 1236 1322


1.5 29 38 52 72 86 101 121 149 178 216 278 376 532 663 816 933 1061 1161

2

2.5

3

Ampacity, Amperes 24 20 18 32 27 24 43 37 33 60 51 45 71 61 53 84 72 63 100 86 75 123 105 93 147 126 111 178 153 134 230 197 173 311 266 234 439 376 331 548 469 413 674 577 508 771 660 581 877 750 661 959 821 723

3.5

4

16 21 29 40 48 56 67 83 99 120 155 209 296 369 454 519 590 645

14 19 26 36 43 51 61 75 90 109 140 189 267 334 410 469 534 584

Table 5-15a 3-1/C Insulated Jacketed Cables Triplexed Cable Diameter



Inches

micro-ohms/ft

Amperes

1.21 1.27 1.38 1.51 1.60 1.68 1.79 1.96 2.09 2.33 2.54 2.89 3.36 3.69 4.12 4.38 4.70 4.92

1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.47 107.43 90.92 65.28 46.07 31.25 24.12 19.88 17.20 15.32 14.00

43 57 74 98 114 131 151 175 202 224 275 342 433 508 574 627 670 711


1.5 36 47 64 89 106 125 149 175 202 224 275 342 433 508 574 627 670 711

2

2.5

3


3.5

4

20 26 36 49 59 69 83 102 122 148 190 258 364 455 560 627 670 711

18 24 32 45 53 63 75 92 110 134 172 233 329 412 506 578 658 711

Table 5-16a 3/C Insulated Jacketed Conductors with Overall Jacket Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.12 1.23 1.33 1.46 1.54 1.63 1.79 1.99 2.11 2.28 2.51 2.92 3.32 3.65 4.14 4.40 4.65 4.88

1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.47 107.43 90.92 65.28 46.07 31.25 24.12 19.88 17.20 15.32 14.00

47 62 81 107 124 142 166 191 222 248 306 384 496 591 674 747 809 865



1.5 33 46 62 86 102 121 149 186 222 248 306 384 496 591 674 747 809 865

2

2.5

3



3.5

4

18 25 35 48 57 67 83 104 123 145 188 261 360 450 562 642 719 790

17 23 31 43 51 61 75 94 112 131 170 236 325 407 509 581 651 714

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---




Ampacities of 5000 Volt Non-shielded Copper Cables Table 5-17 3/C Insulated Conductors with Overall Jacket Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.86 0.94 1.05 1.18 1.26 1.35 1.45 1.56 1.75 1.85 2.08 2.36 2.82 3.15 3.55 3.82 4.17 4.40

866.63 545.28 342.79 215.61 170.96 136.27 108.12 86.25 68.09 58.24 42.55 30.60 22.10 18.15 15.77 14.21 12.99 11.99

53 70 93 123 143 165 191 221 258 286 350 434 544 626 693 750 798 848


1.5 32 44 62 88 105 126 152 183 231 264 347 434 544 626 693 750 798 848

2

2.5

3


3.5

4

18 24 34 49 58 70 84 102 128 147 193 258 363 448 541 614 701 769

16 22 31 44 53 63 76 92 116 133 175 234 329 405 490 555 634 696

Ampacities of 5000 Volt Nonshielded Aluminum Cables Table 5-17a 3/C Insulated Conductors with Overall Jacket Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.86 0.94 1.05 1.18 1.26 1.35 1.45 1.56 1.75 1.85 2.08 2.36 2.82 3.15 3.55 3.82 4.17 4.40

1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.96 107.81 91.25 65.95 46.97 32.37 25.52 21.49 18.91 17.12 15.81

42 55 74 98 114 131 152 176 205 228 282 350 450 528 594 650 695 738


1.5 25 35 49 70 83 100 121 146 184 211 279 350 450 528 594 650 695 738

2

2.5

3


--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---



3.5

4

14 19 27 39 46 56 67 81 102 117 155 209 300 378 464 532 610 670

13 18 25 35 42 50 61 73 92 106 140 189 271 342 419 481 552 606

Ampacities of 5000 Volt Shielded Copper Cables Table 5-18 1/C Insulated Jacketed Cables Cable Diameter



Inches

micro-ohms/ft

Amperes

0.53 0.57 0.61 0.67 0.71 0.75 0.80 0.88 0.94 1.00 1.10 1.25 1.44 1.60 1.92 2.04 2.15 2.26

849.64 534.59 336.07 211.38 167.61 133.12 105.62 83.97 66.08 56.52 40.83 28.85 20.21 16.14 13.49 12.01 10.99 10.19

72 94 125 166 192 222 257 298 346 385 476 599 765 898 1002 1097 1179 1252

Page 27


1.5 34 47 63 87 103 123 147 181 218 251 325 439 604 751 986 1097 1179 1252

2

2.5

3


3.5

4

19 26 35 48 58 68 82 101 121 140 181 244 336 418 548 617 680 743

17 23 32 44 52 62 74 91 110 126 163 221 304 378 496 558 615 672

Table 5-19 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.14 1.23 1.32 1.44 1.53 1.62 1.72 1.90 2.03 2.16 2.37 2.70 3.10 3.45 4.14 4.40 4.64 4.87

866.63 545.28 342.79 215.61 170.96 135.78 107.74 85.65 67.40 57.66 41.65 29.43 20.61 16.47 13.76 12.25 11.21 10.39

61 79 105 138 160 185 214 248 288 320 395 498 636 746 843 921 990 1052


1.5 42 57 78 107 127 151 181 224 269 310 395 498 636 746 843 921 990 1052

2

2.5

3


3.5

4

23 32 43 59 71 84 100 124 150 172 222 301 413 515 676 761 839 915

21 29 39 54 64 76 91 112 135 156 201 273 374 466 611 689 759 828

Table 5-20 3/C Insulated Conductors Plexed with Overall Jacket Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.06 1.15 1.23 1.36 1.45 1.54 1.64 1.81 1.94 2.07 2.29 2.61 3.08 3.42 3.98 4.24 4.48 4.72

866.63 545.28 342.79 215.61 170.96 136.24 108.09 86.21 68.04 58.19 42.49 30.51 21.96 17.99 15.58 14.02 12.85 11.85

61 79 103 136 157 181 208 240 278 308 377 466 580 664 736 796 849 896



1.5 39 54 72 101 121 144 172 212 256 296 377 466 580 664 736 796 849 896

2

2.5

3



3.5

4

22 30 40 56 67 80 96 118 142 164 213 286 398 488 611 686 757 830

20 27 36 51 61 72 86 107 129 149 192 259 360 442 552 620 685 751

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---


ICEA P-54-440 / NEMA WC 51-2008 ANSI/NEMA WC 51-2009/ Page 27 ICEA P-54-440-2009


Ampacities of 5000 Volt Shielded Aluminum Cables Table 5-18a 1/C Insulated Jacketed Cables

Page 28 Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000


Cable Diameter



Inches

micro-ohms/ft

Amperes

0.53 0.57 0.61 0.67 0.71 0.75 0.80 0.88 0.94 1.00 1.10 1.25 1.44 1.60 1.92 2.04 2.15 2.26

1346.79 847.40 532.71 335.08 265.69 210.57 167.06 132.82 105.33 89.16 64.05 45.23 30.75 23.78 19.48 16.85 15.07 13.76

57 75 99 132 153 177 205 237 274 306 380 478 620 740 834 926 1006 1078


1.5 27 37 50 69 82 98 117 144 173 200 259 351 490 619 821 926 1006 1078

2

2.5

3


3.5

4

15 21 28 38 46 54 65 80 96 111 144 195 272 344 456 521 581 639

14 19 25 35 41 49 59 72 87 100 130 176 246 311 413 471 525 578

Table 5-19a 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG or kcmil 8 6 4 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.14 1.23 1.32 1.44 1.53 1.62 1.72 1.90 2.03 2.16 2.37 2.70 3.10 3.45 4.14 4.40 4.64 4.87

1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.48 107.44 90.94 65.33 46.14 31.36 24.26 19.87 17.18 15.37 14.03

48 63 83 110 127 147 170 197 228 254 315 398 515 615 702 778 845 906


1.5 34 46 62 85 101 120 144 178 213 247 315 398 515 615 702 778 845 906

2

2.5

3


3.5

4

19 25 34 47 56 67 80 99 119 137 178 241 335 424 562 643 717 787

17 23 31 43 51 61 72 89 107 124 161 218 303 384 509 581 648 712

Table 5-20a 3/C Insulated Conductors Plexed with Overall Jacket

--```,,``,,`,``,,``,`,,,`,`,,-`


Cable Diameter



Inches

micro-ohms/ft

Amperes

1.06 1.15 1.23 1.36 1.45 1.54 1.64 1.81 1.94 2.07 2.29 2.61 3.08 3.42 3.98 4.24 4.48 4.72

1373.73 864.35 543.36 341.78 271.00 214.78 170.40 135.92 107.78 91.23 65.91 46.91 32.28 25.41 21.35 18.76 17.00 15.68

48 63 82 108 125 144 166 191 222 246 302 376 478 558 629 688 738 779



1.5 31 43 57 80 96 114 137 169 204 236 302 376 478 558 629 688 738 779

2

2.5

3



3.5

4

17 24 32 45 53 64 76 94 113 131 171 231 328 411 522 593 658 722

16 21 29 40 48 58 69 85 102 119 154 209 297 372 472 536 595 653

ICEA P-54-440 / NEMA WC 51-2008 ANSI/NEMA Page WC 51-2009/ 29 ICEA P-54-440-2009

Ampacities of 15000 Volt Shielded Copper Cables

Page 29

Table 5-21 1/C Insulated Jacketed Cables Conductor Size AWG or kcmil 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.87 0.91 0.95 1.00 1.05 1.11 1.17 1.29 1.42 1.61 1.84 2.08 2.20 2.31 2.42

211.38 167.61 133.06 105.58 83.90 66.00 56.46 40.70 28.69 19.98 15.77 13.27 11.77 10.74 9.93

170 195 225 260 300 349 386 477 598 762 890 1000 1092 1175 1250

Calculated Depth of Cables in Tray, Inches 1 146 171 201 237 279 333 379 477 598 762 890 1000 1092 1175 1250

1.5 113 133 155 184 216 258 294 382 500 680 874 1000 1092 1175 1250

2

2.5

3

Ampacity, Amperes 93 80 70 110 94 83 128 110 97 152 130 114 179 153 135 213 182 161 243 208 183 315 270 238 413 354 311 561 481 423 722 618 544 890 762 671 1000 856 753 1099 940 828 1197 1025 902

3.5

4

63 74 86 102 120 143 163 212 278 378 486 599 673 739 805

57 67 78 92 109 130 148 192 252 342 440 542 608 669 729

Table 5-22 3-1/C Insulated Jacketed Cables Triplexed Conductor Size AWG or kcmil 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.88 1.96 2.05 2.16 2.26 2.39 2.52 2.78 3.06 3.47 3.97 4.48 4.74 4.98 5.22

215.61 170.96 135.72 107.69 85.58 67.32 57.59 41.51 29.26 20.38 16.08 13.53 12.00 10.95 10.13

145 166 192 221 254 295 327 404 506 645 753 850 931 1000 1062


1.5 139 163 192 221 254 295 327 404 506 645 753 850 931 1000 1062

2

2.5

3


3.5

4

78 91 107 126 148 176 201 261 343 465 599 738 829 911 993

70 82 96 114 134 160 182 236 310 421 542 667 749 824 898

Table 5-23 3/C Insulated Conductors Plexed with Overall Jacket

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---

Conductor Size AWG or kcmil 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.79 1.88 1.96 2.07 2.18 2.31 2.44 2.70 3.04 3.45 3.81 4.33 4.59 4.82 5.06

215.61 170.96 136.20 108.06 86.17 68.00 58.16 42.42 30.42 21.87 17.87 15.48 13.92 12.75 11.76

142 162 186 214 246 284 314 382 471 582 669 737 794 848 898



1.5 133 157 183 214 246 284 314 382 471 582 669 737 794 848 898

2

2.5

3



3.5

4

74 87 102 121 142 170 194 251 334 447 546 666 745 817 893

67 79 92 109 129 153 175 227 302 404 494 603 674 739 808




Ampacities of 15000 Volt Shielded Aluminum Cables Table 5-21a 1/C Insulated Jacketed Cables

Cable Diameter



Inches

micro-ohms/ft

Amperes

0.87 0.91 0.95 1.00 1.05 1.11 1.17 1.29 1.42 1.61 1.84 2.08 2.20 2.31 2.42

335.08 265.69 210.57 167.06 132.77 105.29 89.12 63.95 45.12 30.60 23.52 19.31 16.66 14.86 13.53

134 155 179 206 238 276 307 380 477 616 729 829 918 999 1071


1.5 90 105 124 146 172 204 234 304 399 549 716 829 918 999 1071

2

2.5

3


3.5

4

50 59 69 81 96 113 130 169 222 305 398 496 565 628 690

45 53 62 73 86 103 118 153 201 276 360 449 511 568 624

Table 5-22a 3-1/C Insulated Jacketed Cables Triplexed Cable Diameter



Inches

micro-ohms/ft

Amperes

1.88 1.96 2.05 2.16 2.26 2.39 2.52 2.78 3.06 3.47 3.97 4.48 4.74 4.98 5.22

341.78 271.00 214.78 170.40 135.43 107.40 90.91 65.23 46.02 31.21 23.99 19.70 16.99 15.15 13.80

115 132 153 176 202 234 261 322 403 521 616 705 782 850 910


1.5 111 130 152 176 202 234 261 322 403 521 616 705 782 850 910

2

2.5

3


3.5

4

62 72 85 100 118 140 160 208 273 376 491 611 696 775 851

56 65 77 91 106 126 145 189 247 340 444 553 630 701 770

Table 5-23a 3/C Insulated Conductors Plexed with Overall Jacket Conductor Size AWG or kcmil 2 1 1/0 2/0 3/0 4/0 250 350 500 750 1000 1250 1500 1750 2000

Cable Diameter



Inches

micro-ohms/ft

Amperes

1.79 1.88 1.96 2.07 2.18 2.31 2.44 2.70 3.04 3.45 3.81 4.33 4.59 4.82 5.06

341.78 271.00 214.78 170.40 135.89 107.76 91.21 65.86 46.85 32.22 25.32 21.28 18.68 16.92 15.59

112 129 149 171 196 226 250 306 380 480 562 628 686 736 781



1.5 105 124 146 171 196 226 250 306 380 480 562 628 686 736 781

2

2.5

3



3.5

4

59 69 81 96 113 135 155 201 269 368 458 568 643 710 776

53 63 73 87 102 122 140 182 243 333 415 514 582 642 702

--```,,``,,`,``,,``,`,,,`,`,,-`-`,,`,,`,`,,`---


ANSI NEMA WC 51-2009 ICEA P-54-440-2009 Ampacities of Cables Installed in Cable Trays

Recommend Documents