Amorphous metal An amorphous metal (also (also known known as metallic glass or glassy metal metal) is a solid metallic material, usually an alloy, with a disordered atomic-scale structure. Most metals are crystalline in their solid state, which means they have a highly ordered arrangement of atoms. Amorphous metals are non-crystalline, and have a glass-like structure. But unlike common glasses, such as window glass, which are typically electrical insulators, amorphous metals me tals have good electrical electric al conductivity. conductivity. There are several ways in which amorphous metals can be produced, includingextremely rapid cooling, physical vapor deposition, solid-state reaction, ion irradiation, and mechanical mechani cal alloying alloy ing..[1][2] In the past, small small batches of amorphous metals have been produced through a variety
Samples of amorphous metal, with millimeter scale
of quick-cool quick-cooling ing methods. For instance, amorphous metal ribbons have been produced by sputtering molten metal onto a spinning metal disk (melt spinning). The rapid cooling, on the order of millions of degrees degrees a second, second, is too fast f or crystals to form and the material is "locked" in a glassy state. More recently a number of alloys with critical critical cooling cooling rates low enough to allow formation of amorphous structure in thick layers (over 1 millimeter) have been produced; these are known as bulk metallic glasses (BMG). More recently, batches of amorphous steel with three times the strength of conventional steel alloys have been produced.
Contents History Properties Applications Applications Modelin Modeling g and theory See also References References External links links
History The first reported metallic glass was an alloy (Au 75 Si25 ) produced at Caltech by W. Klement (Jr.), Willens and Duwez in 1960. [3] This and other early glass-forming alloys had to be cooled extremely rapidly (on the order of one megakelvin per second, 108 K/s) to avoid crystallization. An important consequence of this was that metallic glasses could only be produced in a limited number of forms (typically ribbons, foils, or wires) in which one dimension was small so that heat could be extracted quickly enough to achieve the necessary cooling rate. As a result, metallic glass specimens (with a few exceptions) were were limited to thicknesses of less than one hundred micrometers. In 1969, an alloy of 77.5% palladium, palladium, 6% copper, copper, and 16.5% silicon was found to have critical cooling rate between 100 and 1000 K/s. In 1976, H. Liebermann and C. Graham developed a new method of manufacturing thin ribbons of amorphous metal on a supercooled fast-spinning wheel. wheel.[4] This was an alloy of iron, nickel, phosphorus and boron. The material, known as Metglas, was commercialized in the early 1980s and is used for low-loss power distribution transformers (Amorphous (Amorphous metal transformer). ). Metglas-
2605 is composed of 80% iron and 20% boron, has Curie temperature of 373 °C and a room temperature saturation magnetization of 1.56 teslas.[5] In the early 1980s, glassy ingots with 5 mm diameter were produced from the alloy of 55% palladium, 22.5% lead, and 22.5% antimony, by surface etching followed with heating-cooling cycles. Usingboron oxide flux, the achievable thickness was increased to a centimeter. Research in Tohoku University[6] and Caltech yielded multicomponent alloys based on lanthanum, magnesium, zirconium, palladium, iron, copper, and titanium, with critical cooling rate between 1 K/s to 100 K/s, compara ble to oxide glasses. In 1988, alloys of lanthanum, aluminium, and copper ore were found to be highly glass-forming. Al-based metallic glasses containin [7] Scandium exhibited a record-type tensile mechanical strength of about 1500 MPa.
In the 1990s new alloys were developed that form glasses at cooling rates as low as one kelvin per second. These cooling rates can be achieved by simple casting into metallic molds. These "bulk" amorphous alloys can be cast into parts of up to several centimeters in thickness (the maximum thickness depending on the alloy) while retaining an amorphous structure. The best glass-forming alloys are based on zirconium and palladium, but alloys based on iron, titanium, copper, magnesium, and other metals are also known. Many amorphous alloys are formed by exploiting a phenomenon called the "confusion" effect. Such alloys contain so many different elements (often four or more) that upon cooling at sufficiently fast rates, the constituent atoms simply cannot coordinate themselves into the equilibrium crystalline state before their mobility is stopped. In this way, the random disordered state of the atoms is "locked in". In 1992, the commercial amorphous alloy, Vitreloy 1 (41.2% Zr, 13.8% Ti, 12.5% Cu, 10% Ni, and 22.5% Be), was developed at Caltech, as a part of Department of Energy and NASA research of new aerospace materials. More variants followed. In 2004, bulk amorphous steel (actually rather cast iron owing to high C content) was successfully produced by two groups: one at Oak Ridge National Laboratory, who refers to their product as "glassy steel", and the other at the Universi ty of Virginia, calling theirs "DARVA-Glass 101".[8][9] The product is non-magnetic at room temperature and significantly stronger than conventional steel, [10][11] though a long research and development process remains before the introduction of the material into public or military use.
In 2018 a team at SLAC National Accelerator Laboratory, the National Institute of Standards and Technology (NIST) and Northwestern Universityreported the use of artificial intelligence to predict and evaluate samples of 20,000 different likely metallic [12][13] glass alloys in a year. Their methods promise to speed up research and time to market for new amorphous metals alloys..
Properties Amorphous metal is usually analloy rather than a pure metal. The alloys contain atoms of significantly different sizes, leading to low free volume (and therefore up to orders of magnitude higher viscosity than other metals and alloys) in molten state. The viscosity prevents the atoms moving enough to form an ordered lattice. The material structure also results in low shrinkage during cooling, and resistance to plastic deformation. The absence ofgrain boundaries, the weak spots of crystalline materials, leads to better resistance to wear[14] and corrosion. Amorphous metals, while technically glasses, are also much tougher and less brittle than oxide glasses and ceramics. Thermal conductivity of amorphous materials is lower than that of crystalline metal. As formation of amorphous structure relies on fast cooling, this limits the maximum achievable thickness of amorphous structures. To achieve formation of amorphous structure even during slower cooling, the alloy has to be made of three or more components, leading to complex crystal units with higher potential energy and lower chance of formation. The atomic radius of the components has to be significantly different (over 12%), to achieve high packing density and low free volume. The combination of components should have negative heat of mixing, inhibiting crystal nucleation and prolonging the time the molten metal stays in supercooled state.
The alloys of boron, silicon, phosphorus, and other glass formers with magnetic metals (iron, cobalt, nickel) have high magnetic susceptibility, with low coercivity and high electrical resistance. Usually the conductivity of a metallic glass is of the same low order of magnitude as of a molten metal just above the melting point. The high resistance leads to low losses by eddy currents when subjected to alternating magnetic fields, a property useful for e.g.transformer magnetic cores. Their low coercivity also contributes to low loss. Amorphous metals have higher tensile yield strengths and higher elastic strain limits than polycrystalline metal alloys, but their ductilities and fatigue strengths are lower.[15] Amorphous alloys have a variety of potentially useful properties. In particular, they tend to be stronger than crystalline alloys of similar chemical composition, and they can sustain larger reversible ("elastic") deformations than crystalline alloys. Amorphous metals derive their strength directly from their non-crystalline structure, which does not have any of the defects (such asdislocations) that limit the strength of crystalline alloys. One modern amorphous metal, known as Vitreloy, has a tensile strength that is almost twice that of high-grade titanium. However, metallic glasses at room temperature are not ductile and tend to fail suddenly when loaded in tension, which limits the material applicability in reliability-critical applications, as the impending failure is not evident. Therefore, there is considerable interest in producing metal matrix composites consisting of a metallic glass matrix containing dendritic particles or fibers of a ductile crystalline metal. Perhaps the most useful property of bulk amorphous alloys is that they are true glasses, which means that they soften and flow upon heating. This allows for easy processing, such as by injection molding, in much the same way as polymers. As a result, amorphous alloys have been commercialized for use in sports equipment, medical devices, and as cases for electronic equipment. Thin films of amorphous metals can be deposited viahigh velocity oxygen fueltechnique as protective coatings.
Applications Currently the most important application is due to the special magnetic properties of some ferromagnetic metallic glasses. The low magnetization loss is used in high efficiency transformers (amorphous metal transformer) at line frequency and some higher frequency transformers. Amorphous steel is a very brittle material which makes it difficult to punch into motor laminations.[16] Also electronic article surveillance(such as theft control passive ID tags,) often uses metallic glasses because of these magnetic properties. Amorphous metals exhibit unique softening behavior above their glass transition and this softening has been increasingly explored for thermoplastic forming of metallic glasses.[17] Such low softening temperature allows for developing simple methods for making composites of nanoparticles (e.g. carbon nanotubes) and BMGs. It has been shown that metallic glasses can be patterned on [18] This may solve the problems ofnanoimprint lithography extremely small length scales ranging from 10 nm to several millimeters.
where expensive nano-molds made of silicon break easily. Nano-molds made from metallic glasses are easy to fabricate and more durable than silicon molds. The superior electronic, thermal and mechanical properties of BMGs compared to polymers make them a good option for developing nanocomposites for electronic application such asfield electron emissiondevices.[19] Ti40 Cu36 Pd14Zr10 is believed to be noncarcinogenic, is about three times stronger than titanium, and its elastic modulus nearly matches bones. It has a high wear resistance and does not produce abrasion powder. The alloy does not undergo shrinkage on solidification. A surface structure can be generated that is biologically attachable by surface modification using laser pulses, allowing better joining with bone.[20] Mg60Zn35Ca5, rapidly cooled to achieve amorphous structure, is being investigated, at Lehigh University, as a biomaterial for implantation into bones as screws, pins, or plates, to fix fractures. Unlike traditional steel or titanium, this material dissolves in organisms at a rate of roughly 1 millimeter per month and is replaced with bone tissue. This speed can be adjusted by varying the content of zinc.[21]
Modeling and theory Bulk metallic glasses (BMGs) have now been modeled using atomic scale simulations (within the density functional theory framework) in a similar manner to high entropy alloys.[22][23] This has allowed predictions to be made about their behavior, stability and many more properties. As such, new BMG systems can be tested, and tailored systems; fit for a specific purpose (e.g. bone
replacement or aero-engine component) without as muchempirical searching of the phase space and experimental trial and error.
See also Bioabsorbable metallic glass Glass-ceramic-to-metal seals Liquidmetal Materials science Structure of liquids and glasses Amorphous brazing foil
References 1. Some scientists only consider amorphous metals produced by rapid cooling from a liquid state to be glasses. However, materials scientists commonly consider a glass to be any solid non-crystalline material, regardless of how it is produced. 2. Ojovan, M. I.; Lee, W. B. E. (2010). "Connectivity and glass transition in disordered oxide systems". Journal of NonCrystalline Solids. 356 (44–49): 2534.Bibcode:2010JNCS..356.2534O(http://adsabs.harvard.edu/abs/2010JNCS..3 56.2534O). doi:10.1016/j.jnoncrysol.2010.05.012(https://doi.org/10.1016%2Fj.jnoncrysol.2010.05.012) . 3. Klement, W.; Willens, R. H.; Duwez, POL (1960). "Non-crystalline Structure in Solidified Gold-Silicon Alloys". Nature. 187 (4740): 869–870.Bibcode:1960Natur.187..869K (http://adsabs.harvard.edu/abs/1960Natur .187..869K). doi:10.1038/187869b0 (https://doi.org/10.1038%2F187869b0) . 4. Libermann H. & Graham C. (1976)."Production Of Amorphous Alloy Ribbons And Ef fects Of Apparatus Parameters On Ribbon Dimensions"(http://ieeexplore.ieee.org/xpls/abs_all.jsp?isnumber=22822&arnumber=1059201&count=1 8&index=111). IEEE Transactions on Magnetics. 12 (6): 921. Bibcode:1976ITM....12..921L(http://adsabs.harvard.ed u/abs/1976ITM....12..921L). doi:10.1109/TMAG.1976.1059201(https://doi.org/10.1109%2FTMAG.1976.1059201) . 5. Roya, R & Majumdara, A.K. (1981). "Thermomagnetic and transport properties of metglas 2605 SC and 2605". Journal of Magnetism and Magnetic Materials . 25: 83–89. Bibcode:1981JMMM...25...83R(http://adsabs.harvard.ed u/abs/1981JMMM...25...83R). doi:10.1016/0304-8853(81)90150-5(https://doi.org/10.1016%2F0304-8853%2881%2 990150-5). 6. Inoue, A. (2000). "Stabilization of metallic supercooled liquid and bulk amorphous alloys". Acta Materialia. 48: 279– 306. doi:10.1016/S1359-6454(99)00300-6(https://doi.org/10.1016%2FS1359-6454%2899%2900300-6) . 7. Inoue, A.; Sobu, S.; Louzguine, D. V.; Kimura, H.; Sasamori, K. (2011). "Ultrahigh strength Al-based amorphous alloys containing Sc". Journal of Materials Research. 19 (5): 1539. Bibcode:2004JMatR..19.1539I(http://adsabs.harv ard.edu/abs/2004JMatR..19.1539I). doi:10.1557/JMR.2004.0206(https://doi.org/10.1557%2FJMR.2004.0206) . 8. U.Va. News Service,"University Of Virginia Scientists Discover Amorphous Steel Material is three times stronger than conventional steel and non-magnetic"(http://www.virginia.edu/topnews/releases2004/poon-july-2-2004.html) , U.Va. News Services, 7/2/2004 9. Google Patents listing for Patent WO 2006091875 A2,"Patent WO 2006091875 A2 - Amorphous steel composites with enhanced strengths, elastic properties and ductilities (Also published as US20090025834, WO20060 91875A3)" (http://www.google.com/patents/WO2006091875A2?cl=en), Joseph S Poon, Gary J Shiflet, Univ Virginia, 8/31/2006 10. "Glassy Steel" (http://www.ornl.gov/info/ornlreview/v38_1_05/article17.shtml). ORNL Review . 38 (1). 2005. 11. Ponnambalam, V.; Poon, S. J.; Shiflet, G. J. (2011). "Fe-based bulk metallic glasses with diameter thickness larger than one centimeter". Journal of Materials Research. 19 (5): 1320. Bibcode:2004JMatR..19.1320P(http://adsabs.har vard.edu/abs/2004JMatR..19.1320P). doi:10.1557/JMR.2004.0176(https://doi.org/10.1557%2FJMR.2004.0176) . 12. "Artificial intelligence accelerates discovery of metallic glass"(https://phys.org/news/2018-04-artificial-intelligence-dis covery-metallic-glass.html). Physorg. April 13, 2018. Retrieved 2018-04-14. 13. Ren, Fang; Ward, Logan; Williams, Travis; Laws, Kevin J.; Wolverton, Christopher; Hattrick-Simpers, Jason; Mehta, Apurva (2018-04-01)."Accelerated discovery of metallic glasses through iteration of machine learning and highthroughput experiments"(http://advances.sciencemag.org/content/4/4/eaaq1566) . Science Advances. 4 (4): eaaq1566. doi:10.1126/sciadv.aaq1566 (https://doi.org/10.1126%2Fsciadv.aaq1566). ISSN 2375-2548 (https://www. worldcat.org/issn/2375-2548). PMID 29662953 (https://www.ncbi.nlm.nih.gov/pubmed/29662953).
14. Gloriant, Thierry (2003)."Microhardness and abrasive wear resistance of metallic glasses and nanostructured composite materials"(https://doi.org/10.1016/S0022-3093(02)01941-5) . Journal of Non-Crystalline Solids. 316 (1): 96–103. Bibcode:2003JNCS..316...96G(http://adsabs.harvard.edu/abs/2003JNCS..316...96G) . doi:10.1016/s00223093(02)01941-5 (https://doi.org/10.1016%2Fs0022-3093%2802%2901941-5) . 15. Russell, Alan & Lee, Kok Loong (2005).Structure-Property Relations in Nonferrous Metals(https://books.google.co m/books?id=fIu58uZTE-gC). John Wiley & Sons. p. 92. ISBN 9780471708537. 16. Ning, S. R.; Gao, J.; Wang, Y. G. (2010). "Review on Applications of Low Loss Amorphous Metals in Motors". Advanced Materials Research. 129-131: 1366.doi:10.4028/www.scientific.net/AMR.129-131.1366 (https://doi.org/10. 4028%2Fwww.scientific.net%2FAMR.129-131.1366). 17. Saotome, Y.; Iwazaki, H. (2000). "Superplastic extrusion of microgear shaft of 10 μm in module". Microsystem Technologies. 6 (4): 126. doi:10.1007/s005420050180(https://doi.org/10.1007%2Fs005420050180) . 18. Kumar, G.; Tang, H. X.; Schroers, J. (2009). "Nanomoulding with amorphous metals". Nature. 457 (7231): 868–872. Bibcode:2009Natur.457..868K (http://adsabs.harvard.edu/abs/2009Natur .457..868K). doi:10.1038/nature07718(http s://doi.org/10.1038%2Fnature07718). PMID 19212407 (https://www.ncbi.nlm.nih.gov/pubmed/19212407). 19. Hojati-Talemi, Pejman (2011). "High performance bulk metallic glass/carbon nanotube composite cathodes for electron field emission". Applied Physics Letters. 99 (19): 194104.Bibcode:2011ApPhL..99s4104H(http://adsabs.ha rvard.edu/abs/2011ApPhL..99s4104H). doi:10.1063/1.3659898(https://doi.org/10.1063%2F1.3659898). 20. Maruyama, Masaaki (June 11, 2009)."Japanese Universities Develop Ti-based Metallic Glass for Artificial Finger Joint" (http://techon.nikkeibp.co.jp/english/NEWS_EN/20090610/171551/?P=1) . Tech-on. 21. "Fixing bones with dissolvable glass"(http://physicsworld.com/cws/article/news/40573) . Institute of Physics. October 1, 2009. 22. King, D.M.; Middleburgh, S.C.; Liu, A.C.Y .; Tahini, H.A.; Lumpkin, G.R.; Cortie, M. (January 2014). "Formation and structure of V–Zr amorphous alloy thin films". Acta Materialia. 83: 269–275. doi:10.1016/j.actamat.2014.10.016(http s://doi.org/10.1016%2Fj.actamat.2014.10.016) . 23. Middleburgh, S.C.; Burr, P.A.; King, D.M.; Edwards, L.; Lumpkin, G.R.; Grimes, R.W. (November 2015). "Structural stability and fission product behaviour in U3Si". Journal of Nuclear Materials. 466: 739–744. Bibcode:2015JNuM..466..739M(http://adsabs.harvard.edu/abs/2015JNuM..466..739M) . doi:10.1016/j.jnucmat.2015.04.052(https://doi.org/10.1016%2Fj.jnucmat.2015.04.052) .
External links Liquidmetal Design Guide "Metallic glass: a drop of the hard stuf f" at New Scientist Glass-Like Metal Performs Better Under StressPhysical Review Focus, June 9, 2005 "Overview of metallic glasses" New Computational Method Developed By Carnegie Mellon University Physicist Could Speed Design and esting T of Metallic Glass (2004) (the alloy database developed by Marek Mihalkovic, Michael Widom, and others) Materials Today: The case for bulk metallic glass New tungsten-tantalum-copper amorphous alloy developed at the Korea Advanced Institute of Science and Technology [1] Amorphous Metals in Electric-Power Distribution Applications Amorphous and Nanocrystalline Soft Magnets glass transition temperatures of bulk metallic glasses "New metallic glass material created by starving it of nuclei" . newatlas.com. Retrieved 2017-12-09. Retrieved from "https://en.wikipedia.org/w/index.php?title=Amorphous_metal&oldid=838815986 "
This page was last edited on 29 April 2018, at 13:22. Text is available under theCreative Commons Attribution-ShareAlike License ; additional terms may apply. By using this site, you agree to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark of theWikimedia Foundation, Inc., a non-profit organization.
