Abis Over IP Configuration Locally From the BTS Side

Abis over IP configuration locally from the BTS side 1. Ensure the Network Connectivity Connectivity to t he BSC: To ensure the network connectivity to the BSC, you have to do the foll owing: a- connect the upli nk of the BTS (Ethernet cable) to your PC 1=> PC Ethernet port ). ( Example:- EMS6 port 1=> ).

b- Set the IP Address of the PC Like Like the BTS IP, the Default Gateway Gateway like the Default Default Gateway Gateway of the BTS (forward route address in the BTS BTS IP route) , with a Subnet Mask Mask that al lows the IP Address and the Default Gateway to be in the same subnet. Example:

Gateway

BTS IP

10.164.25.41

10.164.25.44

BSC IP

Sub net Mask

Mask IP

10.164.24.12 255.255.255.2 255.255.255 .248 48 10.164.24.8

PC IP Address should be configured as foll ows:

c- Ping the Default gateway & the BSC IP from the CMD CMD of your PC, the result should shoul d be as follows:

d- Now, we are sure that the network connectivi ty to the gateway is OK. Note :- to check connection to BSC DC team mast config router and then ping on BSC IP address

2- Connect locally to the BTS through the Site Maintenance Terminal (SMT):

a- Connect the Site Maintenance Terminal (SMT) PC to the Ethernet port on the GTMU (ETH) through an Ethernet cable. b- Ensure that IP address and subnet mask of the SMT PC are set correctly. The IP address is in the same network segment as the IP address (192.168.0.72/255.255.255.0) of the BTS.

c- To verify the network connection between the computer and the BTS Run ping 192.168.0.72 from the CMD on the computer.

d- After ensuring the local connectivity to the BTS as above, open the Site Maintenance Terminal (SMT). And make configuratio n as following steps Note: If the BTS OML has been established, run the LST BTSLOCALETHPORT

command on the BSC LMT to check whether the ETH port is enabled. If not, run the SET BTSLOCALETHPORT command to enable the port.

3- Access the SMT by the User Name:- admin and Password :-hwbs@com

4- After accessing the SMT, you have to get the management of the BTS. Double click the “Site Management Right” and press the “Get” push button as below:

5- Double click the “IP Over FE Static IP” to start the BTS local configuration

a-Config BTS,BSC and VLAN      

Click config tap Static IP status => Enable Com type => port IP BTS IP address=>10.164.25.44 BSC IP Address =>10.164.24.12 Press OK



Click on static query tap and press OK to ensure data entry succeed

b- Config Port IP         

Click on Config tap Rack Number =>0 Sub Rack Number=>0 Slot Number =>6 Port Type=> Ethernet Port Port Number =>0 FE0 IP Address =>10.164.25.44(BTS IP) FE0 IP mask address =>255.255.255.248 Press OK




c- Config Route 

Click on Config tap

Rack Number =>0 Sub Rack Number=>0 Slot Number =>6 Destination IP Address =>10.164.24.8 Destination Mask Address =>255.255.255.248 Route Type => Next Next Hop IP Address =>10.164.25.41

      




6-To release the site management double clicks the “Site Management Right” and click “release”.

7- Finally, you can take off the Ethernet cable from the “ETH” port of the GTMU, and waiting for about 5 minutes to check the Leds status of the port “FE0” and ensure that the BTS became UP and managed from the Web LMT (You can also check with NOC to ensure this Issue).

Note: All IP address and IP masks change due to Site and BSC IDs

Abis Over IP Configuration Locally From the BTS Side

Recommend Documents