92974210-Lte-Kpi-Dt-Guide-Measure-Method.pdf

LTE KPI DT GUIDE & MEASURE METHOD

SECRET

Product name

Confidentiality level

LTE RNP/RNO

Internal Open

Product version

Total 34 pages


Prepared by

Date

Hu Wei

Reviewed by

Date

Reviewed by

Date

Approved by

Date

2011-11-29

Huawei Technologies Co., Ltd. All rights reserved.

Huawei Confidential No spreading without permission

Page 1 of 34


SECRET

Revision record Date

Revision version

change Description

Author

2011-11-29

V 1.0

First version finished

Hu Wei 00135858


Page 2 of 34


SECRET

Contents 1. SSV Test....................................................................................................................................................................4 2. KPI Test.....................................................................................................................................................................7 3. Measure Method......................................................................................................................................................33


Page 3 of 34


SECRET

1. SSV Test 1) First should check the azimuth and tilt, any problem the work should be stopped and directly inform Huawei the problems. 2) The DT teams should select points as below (updated: 1,4,7 are canceled, only 6 points needed) to do the network entry/ Download/ upload/ ping test. The points location can be changed as the real signal condition.

3) If the teams find any problem (include but not only: wrong BSID or PCI; low throughput; high ping delay) in the test they should report it to coordinator right now. Take care on the feeder across! At last finish and submit the SSV report (refer to the attachment). 4) If there is no cross feeder, the terminal should access to correct BSID and correct PCI. If there is cross feeder, please report to Huawei SSV Huawei Confidential No spreading without permission

Page 4 of 34

SECRET


supervisor. And the remaining test for this site should be stopped. 5) Throughput test should be done with FTP. Currently, there is one Huawei FTP is available for throughput test. FTP IP: ftp://10.218.240.115/ user name: huawei, password: huawei; ftp://10.212.195.139/ user name: wimax, password: wimax. Please use FTP software (suggest to use filezilla, because it can download several files together.) to download the files (at least 10 files together) at least for 1 minute. Using first stopwatch of DU meter to record the average DL/UL throughput during test.

6) All the throughput test mentioned in this document must be performed in this way. 7) Ping test: click “start” button on your desktop and then: Start-> Run-> input ”cmd”->

enter->

input

”ping

10.218.240.115

–n

100”

or

”ping

10.212.195.139 –n 100” > enter-> wait until output 10 ping delay result on the screen-> record the average ping delay 8) Take a snapshot which includes all the above test result (ping and download, upload), signal information, PCI, terminal Tx power, etc. Huawei Confidential No spreading without permission

Page 5 of 34


SECRET

9) Record each point’s coordinates.


Page 6 of 34

SECRET


2. KPI Test If the SSV test is clear, the teams can go ahead to the KPI test. KPI test include Drier test and Points test. 1)

Tools prepared:

i.

LTE Dongle (E398s)

ii.

Genex Probe(V2R3)

iii. iv. 2) v.

vi.

Genex Probe HardwareDog GPS Softwares prepared: Install software of LTE Dongle and Agent

Inster LTE Dongle in your laptop, you will see the picture

on “My

Computer”, then Double-click this picture, auto install the software.

vii.

Next phase install “Hisi UE Agent”

viii.

Please confirm the LTE Dongle、GPS and Probe Dog in your laptop.

ix.

Open Hisi UE Agent

x.

Open Genex Probe(V2R3)


.

Page 7 of 34


xi.

SECRET

New LTE template:

xii.

Then clean up template like this:

xiii.

New Engineering Parameter


Page 8 of 34


xiv.

Import File

xv.

Select File, the Engineering Paremeter will be provided by huawei.


SECRET

Page 9 of 34


xvi.

Finish Import File

xvii.

Engineering Apply


SECRET

Page 10 of 34


xviii.

SECRET

Device Configure


Page 11 of 34


xix.

Add MS

xx.

Finish MS Add


SECRET

Page 12 of 34


xxi.

SECRET

Add GPS


Page 13 of 34


xxii.

Finish GPS Add

xxiii.

New Test Plan


SECRET

Page 14 of 34


xxiv.

SECRET

Loading-in Test Plan, the test plan will be provided by huawei. But you need to change FTP Upload file to your local file(20M).


Page 15 of 34



SECRET

Page 16 of 34


xxv.

Open Map

xxvi.

Open Geoset File


SECRET

Page 17 of 34


xxvii.

SECRET

Select Map File(TAR file), the map file will be provided by huawei


Page 18 of 34


xxviii.

SECRET

Set Cell Radius


Page 19 of 34



SECRET

Page 20 of 34


xxix.

SECRET

Set Lable


Page 21 of 34



SECRET

Page 22 of 34


xxx.

Finish all setting, then “connect” to LTE Dongle and GPS.

xxxi.

Please begin the log recording before DT, you need to open test plan, then


SECRET

Page 23 of 34


SECRET

begin to log recording and save.


Page 24 of 34


3)

i.

SECRET

Begin DT The DT will follow before confirmed wimax DT boundary. Using Huawei E398s USB terminal and Huawei Genex Probe DT software to perform the DT. During the DT the engineers should parallel perform network entry, minimum guarantee DownLoad/UpLoad test. By this after the DT can get the test result of coverage probability/ successful setup rate / session establish delay/ dropped session rate/ minimum rate guarantee of downstream&upstream/ handoff/ wireless link burst error rate.

ii.

All the streets should be covered. The speed should less than 30km/h. In the DT engineers should always pay attention on the PCI/RSRP/SINR. If any problem happened they should click the “pause” button to pause the test and after solving continue the test. Any problems like KPI fail to achieve must be informed to Huawei on time. After DT the log should be transferred to Huawei.

iii.

In the DT the team should always take care the PCI and performance, the bad performance DT log or wrong test log will need repeating work. It is ok


Page 25 of 34


SECRET

that feedback the problems to Huawei when you meet some problems.

4)

i.

Begin PT Cell edge coverage probability

To the cell edge coverage probability, select 20 edge points (SINR is higher than 0dB but lower than 5dB & RSRP is lower than -100dB) to perform ftp download, each point last 1 min. Record the detail coordinates and test results. The RSRP and SINR must be check from Probe, you can use test plan to download and take a Snapshots like the “Average downstream throughput – sector level” pictures, check the RSRP and SINR like this picture:

Acceptable range: successful rate> 80% Target range: successful rate> 85% ii.

Average downstream throughput – terminal level To the average downstream/upstream throughput (terminal level), select 3 points of one sector (RSRP=-105~-95 / -95~-80/ >80 、SINR=0~10/15~25/25~35) to perform the ftp download/ upload for 1 min.


Page 26 of 34


SECRET

Record the average throughput of the 3 points. This test should be implemented for 20% of sectors per cluster. Please pay more attention to 3 points: RSRP=-105~-95,SINR=0~10, keep the DL throughput between 5M to 15M RSRP=-95~-80, SINR=15~25, keep the DL throughput between 25M to 35M RSRP>-80, SINR=25~35, keep the DL throughput between 45M to 55M The RSRP must be check from Probe, then you can test plan to finish this work.This test plan PT will be provided by huawei. And you need to take a Snapshots like the “Average downstream throughput – sector level” pictures. DL: Acceptable range: the result should higher than 4 Mbps ; Target range: the result should higher than 4 Mbps; UL: Acceptable range: the result should higher than 1 Mbps ; Target range: the result should higher than 1 Mbps ; iii.

Average downstream throughput – sector level To the average downstream/upstream throughput (sector level), use 2 terminal to perform the ftp download/ upload for 1 min at the same time. One point must be meet the condition of Rank2 SINR1 >20 dB. The other point must be meet the condition of MCS (in 16QAM) between 10 to 16(as below table). This test should be implemented for 20% of sectors per cluster.


Page 27 of 34


SECRET

Please pay more attention to the DL throughput of one point must over 35M. The DL throughput of the other point must over 15M. In addition, you need to add MCS to your PT logs, like this snapshot to open MCS, and check DL MCS:


Page 28 of 34


SECRET

The Rank2 SINR1 and MCS must be check from Probe, you can use FileZilla or test plan, this test plan PT will be provided by huawei. And you need to take a Snapshots like this:


Page 29 of 34


SECRET

DL Snapshot

UL Snapshot


Page 30 of 34


iv.

SECRET

Maximum round trip latency To the Maximum round trip latency, select 1 edge point to perform the ping test. This point must be meet the condition of -100
Acceptable range: the average value is less than 60 ms; Target range: the average value is less than 50 ms; v.

Maximum Jitteryf Calculate the maximum jitter based on above ping result. 5 biggest jitter values can be canceled. This test should be implemented for 20% of sectors per cluster. Acceptable range: less than 30 ms; Target range: less than 20 ms;


Page 31 of 34


SECRET

The LTE Stationary KPI template in here, please finish this PT test report use this template.

Wimax<E Mobi l y_LTE PT report t empl et e. xl s

5)

Each Work Output:

i.

SSV report;

ii.

DT logs. Snapshots for Cell edge coverage probability, sector level throughput, terminal level throughput; the result summary table (refer to attachment) Round trip latency test detail by excel file;


Page 32 of 34


SECRET

3. Measure Method KPI Test includes DT and PT (point test). 1) DT: i. The DT will follow before confirmed wimax DT boundary. Using Huawei E398s USB terminal and Huawei Genex Probe&Assistant DT software to perform the DT. During the DT the engineers should parallel perform network entry, minimum guarantee DownLoad/UpLoad test. By this after the DT can get the test result of coverage probability/ successful setup rate / session establish delay/ dropped session rate/ minimum rate guarantee of downstream&upstream/ handoff/ HSR/ wireless link burst error rate. ii. To the coverage probability, need to show out the statistic of points percentage of RSRP>-110dBm&SINR>-3dB, show the RSRP & SINR & PCI map picture. iii. Successful setup rate= ERAB Setup Success Counter / ( ERAB Setup Success Counter + ERAB Setup Failure Counter); iv. Session establishment delay= T(Attach CMP)-T(Attach REQ); v. Dropped session rate= ERAB Abnormal Rel Counter / ERAB Setup Suc Counter. To the minimum rate guarantee of downstream&upstream, the vi. engineers will perform ftp download and upload by one fixed size file (DL 80MB and UL 20MB) with non-GBR account, the download&upload will be ceaselessly repeated until finish the DT. Then calculate the average throughput of these tests. The test result will be filtered as contract requirements and only the valid service result will be calculated. This after filter result will be the KPI result of this test item. vii. Handover successful rate(HSR)= HO Success Counter / ( HO Success Counter + HO Failure Counter); viii. In any 1 min of the DT cannot happen more than 6 times HO, if this not happen, the handoff test is passed. ix. To the wireless link burst error rate, calculate the average RBLER in the DT, the average RBLER of the DT should be less than 1% to achieve the contract KPI. All the above test result will be filtered as the RF test condition x. defined in contract and the final result listed in the report should base on the test result after this filter. The service drop or test fail happened at bad RF points defined by contract will be excluded. Besides, Huawei should provide all the original logs when submit the KPI reports. Huawei Confidential No spreading without permission

Page 33 of 34


SECRET

2) PT: xi. To the cell edge coverage probability, select 20 edge points (SINR is higher than 0dB but lower than 5dB & RSRP is lower than -95dBm) to perform ftp download, each point last 1 min. Do a statistic for the successful service points percentage. To the average downstream/upstream throughput (terminal level), xii. select 3 points (RSRP=-105~-95 / -95~-80/ >-80) to perform the ftp download/ upload for 1 min. Record the average throughput of the 3 points. This test should be implemented for 20% of sectors per cluster xiii. To the average downstream/upstream throughput (sector level), use 2 or 3 terminals (can be negotiated by Mobily & Huawei to detail test requiremtns) to perform the ftp download/ upload for 1 min at the same time. In the 2 terminals condition the modulation should be around 64QAM and 16QAM. This test should be implemented for 20% of sectors per cluster. xiv. To the Maximum round trip latency, select 1 edge point (RSRP=-100~90) to perform the ping test. The ping packet size is 32KB and the ping repeat times is 100. Record the average ping delay. This test should be implemented for 20% of sectors per cluster. xv. Calculate the maximum jitter based on above ping result. 5 biggest jitter values should be canceled. This test should be implemented for 20% of sectors per cluster. xvi. As contract requirements, if the site has other commercial users, the throughput KPI is not must achieved, DT team just normally record the test result & the slot occupy rate from NOC M2000. For that the test is a long term work and the ftp problem is always met, as to avoid any delay by the ftp server, to all the ftp related test items Huawei can use either Mobily ftp server (ftp.bayanat.com.sa) or Huawei server. Huawei should provide all the original logs when submit the KPI xvii. reports. xviii. KPI test report template

LTE- KPI Report_Dawadmi. ppt


Page 34 of 34

92974210-Lte-Kpi-Dt-Guide-Measure-Method.pdf

Recommend Documents