73311424 MSOFTX3000 Engineering Training Practice Guide

MSOFTX3000 Product Training Practice Exercise Guide

MSOFTX3000 Engineering Training Practice Guide

Contents

Contents MSOFTX3000 Hardware System.................................................................................................1 1. Objectives ................................................................................................................................1 2. Reference ................................................................................................................................1 3. Exercise in lab..........................................................................................................................2

BAM O&M.....................................................................................................................................7 1. Objectives ................................................................................................................................7 2. Reference ................................................................................................................................7 3. Exercise in lab..........................................................................................................................8

MSOFTX3000 Hardware Data Configuration ............................................................................15 1. Objectives ..............................................................................................................................15 2. Reference ..............................................................................................................................15 3. Exercise in lab........................................................................................................................16

MSOFTX3000 Mc Interface Configuration.................................................................................22 1. Objectives ..............................................................................................................................22 2. Reference ..............................................................................................................................22 3. Exercise in lab........................................................................................................................23

MSOFTX3000 Local Office Configuration..................................................................................27 1. Objectives ..............................................................................................................................27 2. Reference ..............................................................................................................................27 3. Exercise in lab........................................................................................................................27

MSOFTX3000 Interworking with HLR Configuration .................................................................31 1. Objectives ..............................................................................................................................31 2. Reference ..............................................................................................................................31 3. Exercise in lab........................................................................................................................32

MSOFTX3000 Interworking with BSC Configuration .................................................................36 1. Objectives ..............................................................................................................................36 2. Reference ..............................................................................................................................36 3. Exercise in lab (Practice M2UA) ...........................................................................................37

MSOFTX3000 Interworking with PSTN......................................................................................42 1. Objectives ..............................................................................................................................42 2. Reference ..............................................................................................................................42 3. Exercise in lab (Practice M3UA) ............................................................................................43

MSOFTX3000 Number Analysis Configuration .........................................................................47 1. Objectives ..............................................................................................................................53 2. Reference ..............................................................................................................................53 3. Exercise in lab........................................................................................................................54

Appendix A: Parameter referencing relationship .......................................................................55 1. Part 1 Hardware.....................................................................................................................55 2. Part 2 Mc interface................................................................................................................55 3. Part 3 Local office ..................................................................................................................56 Confidential Information of Huawei. No Spreading without Permission

i

MSOFTX3000 Product Training Pratice Exercise Guide

Contents

4. Part 4 MTP layer ....................................................................................................................57 5. Part 5 SCCP layer..................................................................................................................58 6. Part 6 M2UA layer..................................................................................................................59 7. Part 7 M3UA layer..................................................................................................................60 8. Part 8 Remote office ..............................................................................................................61 9. Part 9 A interface ...................................................................................................................62 10. Part 10 Trunk .......................................................................................................................62

Appendix B: Common used Commands ....................................................................................63

ii

Confidential Information of Huawei. No Spreading without Permission


Contents

MSOFTX3000 Hardware System 1.Objectives Knowledge title

Requirement

The architecture of MSOFTX3000

Know

Know about the bus types and their function

Know

Master board functions, interfaces ,indicators and DIP switch

Master

2.Reference In order to know detailed explanation of the result, please ask the instructor or refer to the product CD . The corresponding path in the CD is MSOFTX3000 Hardware Description MSOFTX3000 System Principle You can press “Ctrl+F” to search the command you need.


.1


3.Exercise in lab Task1 Observe the indicator on the board, try to remember the meaning on different frequency. Position

Meaning

Status Description

LINK

physical connection is normal

glowing

physical connection is abnormal

stop glowing

ACK

flashing

some data are being received or transmitted

ALM

on

reset or faulty

RUN

on for 0.125s, off for 0.125s

loading program

on for 1s, off for 1s

normal running

off

Board is not normally started

on

It is allowed to pull the board out.

OFFLINE

2



Contents

Task2 Observe the physical connection among back boards , you can compare it with the picture below : Part 1 Physical connection between WHSC and WSIU board


.3


LAN Switch

LAN Switch

Part 2 Physical connection between KVMS and BAM as well as iGWB

4



Contents

Part 3 Physical connection of clock line

W C KI B I TS B I TS L I NE L I NE

W C KI

1 2 1 2

B I TS B I TS L I NE L I NE

BIT S 1

BI T S 2

1 2 1 2

1

2

1

2

3

4

3

4

5

6

5

6

7

8

7

8

9

10

9

10

11

12

11

12

13

14

13

14

15

16

15

16


.5


6



Contents

BAM O&M 1.Objectives Knowledge title

Requirement

Check BAM RAID 1 setting, hard disk partition

Master

SQL Server installing

Master

Windows 2000 Server installing, setting Windows 2000 Server to support Chinese, changing system administrator password

Master

BAM software installing and upgrading, BAM automatic login setting, BAM network adapter setting, BAM database backup and restoration, BAM process makeup and function, BAM catalog structure

Master

Emergency workstation installing, emergency workstation net adepter setting, emergency workstation backup path setting

Master

Host hardware data configuration and note

Master

2.Reference Product CD MSOFTX3000 GUI Reference

Using GUI on the BAM


.7


3.Exercise in lab Task1

Backup database with command Step 1 Open F:/MSOFTX3000 Step 2 Execute the command BKP DB Step 3 Observe the folder F:/MSOFTX3000 , try to find out the backup files .

Task2

Backup database with SQL SERVER choose Start > Programs > Microsoft SQL Server > Enterprise Manager.

Operate following the bellowing pictures:

8




Contents

.9


10



Task3

Contents

Restore database with SQL SERVER Stop the BAMService. choose Start > Programs > Administrative Tools > Services


.11


Select BAMService, and right-click it. In the shortcut menu, click Stop. Stop the Smirror service. Stop all BAM service processes.

choose Start > Programs>Microsoft SQLServer > Enterprise Manager.

e SQL database.

12




Contents

.13


Start the BAM manager Start the Smirror service. Start the BAM service Format all data in the SQL database. 1.

Switch to the offline status by running the command LOF;

2.

Set the format switch to ON by running the command SET FMT: STS=ON;

3.

Format all data by running the command FMT;

4.

Switch to the online status by running the command LON; Check whether the foreground and background data is consistent.

Run the command STR CRC to check the consistency If inconsistency , run SND SPD to send inconsistency data from bam to host

14



Contents

MSOFTX3000 Hardware Data Configuration 1.Objectives Knowledge title

Requirement

Data configuration with MSOFTX3000 LMT

Master

Complete hardware data configuration

Master

2.Reference Product CD MSOFTX3000 Configuration Guide

Configueing Equipment Data


.15


3.Exercise in lab Task1 Collect board configuration information ,and input the board name on the tables below: Basic Frame: Front

Slot No

0

1 2

3 4 5

Back

W

W

W

U

U

S

S

A

P

P

M

M

L

W

W

U

U

U

R

R

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

W

W

W

W

W

W

U

U

S

H

S

H

C

C

P

P

I

S

I

S

K

K

W

W

U

C

U

C

I

I

R

R

Expansion Frame 1: Front

Slot No Back

16

0 1 2 3 4 5

W

W

W

U

U

S

S

A

P

P

M

M

L

W

W

U

U

U

R

R

6

7

8

9

10

11

12

13

14

15

16

W

W

W

W

U

U

S

H

S

H

P

P

I

S

I

S

W

W

U

C

U

C

R

R


17

18

19

20


Contents

Expansion Frame 2: Front

Slot No

0 1 2 3 4

Back

Task2

5

W

W

W

U

U

S

S

A

P

P

M

M

L

W

W

U

U

U

R

R

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

W

W

W

W

U

U

S

H

S

H

P

P

I

S

I

S

W

W

U

C

U

C

R

R

Configure Shelf , Frame, and all boards ADD SHF

Shelf NO=0

Shelf NO=1

SHELF 0

SHELF 1

Shelf NO=2

SHELF 2

Attention: Shelf number range is: 0~2. From left to right , the number get larger and larger.


.17


ADD FRM

1

Three 5

Three 9

Three

0

Two

4

Two

8

Two

iGWB

One

3

One

7

One

BAM

Zero 2

Zero 6

Attention: Frame number range : 0~9

Position number range : Zero~Three

ADD BRD

Attention: Please input the module number according to the tip.

Task3

Configure the characteristics of WEPI,WCDB,WIFM ADD EPICFG

18

Zero

Add E1 information.

E1 port

Balance mode

Double-frame

NONBALANCED



ADD CDBFUNC

Contents

Configure the function of WCDB board.

Module number

Function

Refer to “ADD BRD” of WCDB

Select all

ADD FECFG

Add FE port information.

Module number

IP address

Refer to “ADD BRD” of WIFM

Task4

Configure clock information SET CKICFG (Configure clock reference source .) We can use default value in the lab.

ADD BOSRC (Configure the corresponding WEPI board and E1 number , which provides the line clock.)

Task5

Frame number

Slot number

E1 number

The frame that WEPI belongs to

WEPI

0~7

Check the result of hardware data configuration Learn to use the command “LST” , execute the the following commands: LST SHF;

LST FRM;

LST BRD ;

LST EPICFG;

LST CDBFUNC;

LST FECFG;

LST CKICFG;

LST BOSRC;

LST MDU;

for example:


.19


Attention : If we don’t input any number into the blank “Shelf number” , it will list all of the shelfs.

Learn to use the command “DSP” , execute the the following commands: DSP FRM;

DSP BRD;

With the command DSP FRM , you can check the status of all boards in one frame . With the command DSP BRD, you can check the status of one board .

DSP CLKSTAT (Display the clock status of the board, the normal result should be like this:)

%%DSP CLKSTAT: FN=0, SN=0;%% RETCODE = 0 Operation succeeded Clock Status Information -----------------------H.110 CTA Status = Normal H.110 CTB Status = Normal Current CT Clock = CTA H110 clock role = Prime master 2M Clock E1 Port = Port 0 2M Clock Status = Open

DSP CLKPH : Checking Phase-Locked Status of Clock Source, the normal result should be “Locking”, otherwise ,please check the hardware connection and data configuration.

Task6 Practice hardware maintenance commands DSP PDB: Displaying the status of a PDB (power distribution box)

20



Contents

DSP ENVSTAT: Displaying the environment information

DSP FAN: Displaying the fan status

DSP COMM: Displaying the communication status of a board

DSP PORT : Displaying the port status including E1, FE, ATM and ATM 2M and HSC.

DSP BAMST : Displaying the BAM status including CPU and memory utilization Disk status OS version and patch DBMS version and patch Software installed Language of OS and DBMS

DSP MEM: Displaying the module memory DSP FLASHMEM: Displaying the state of the board flash memory


.21


MSOFTX3000 Mc Interface Configuration 1.Objectives Knowledge title

Requirement

Establish H248 link between MSOFTX3000 and UMG8900, make sure VMGW can register.

Master

Task Information collection and planning Complete Mc interface data configuration Problem localization


22

Configue MGW Data



Contents


Configure the data of MGW ADD MGW (Add the information of MGW to MSOFTX3000)

Transport protocol SCTP

WMGC module number

BCU ID

Refer to “ADD BRD” of WMGC

Server/Client Server

ADD H248LNK (Add the link between MSOFTX3000 and MGW.) Transport protocol SCTP

Task2

WBSG module number

Local IP

Local port

Remote IP

Remote port

Refer to “ADD BRD” of WBSG

Check the status of Mc interface DSP MGW ,the normal status of Media Gateway should be”Nomal”

-----------------------Media Gateway = Normal Config Version = 1 Current Version = 1

DSP H248LNK ,the normal status of SCTPAddreState should be ”valid”.

-------------------------------------------ModuleNo MGAIndex TransType LinkNO AssociationId 211 0 SCTP 0 41

Task3

SCTPAddreState Valid

Activate and deactivate Mc interface ,on the same time, observe the trace of this interface Start the trace of Mc interface , which is shown as below :


.23


Step 2 : ACT MGW : activate Mc interface , observe the trace

Double click the trace , observe the detailed information in the message. Step 3 : DEA MGW : deactivate Mc interface, observe the trace

Double click the trace , observe the detailed information in the message.

24



Contents

Task 4 : Learn to use “ping” tool ,check the physical connection of Mc interface Step1: Start the tool “ping”, which is shown as below(The IP address and module number are only example, it depends !) :

Step2: Observe the result , if the connection is normal , there will be reply from remote side , which is shown below:


.25


26



Contents

MSOFTX3000 Local Office Configuration 1.Objectives Knowledge title

Requirement

Related concepts and function of MSOFTX3000 office information

Know

MSOFTX3000 office data configuration

Master

Related command to MSOFTX3000 office configuration

Know

Addressing way of MSOFTX3000

Know

Task Collect information necessary in office configuration Complete office configuration


Configue Office Information Data


Configure the data of local office Step1: SET OFI (Set local office information) Confidential Information of Huawei. No Spreading without Permission

.27


Local office Type

National

National reserved

Local area code

Country code

LOCMSC

National network code

National reserved network code

Step2: SET INOFFMSC (Set local mobile network information)

Local MSC number

Local VLR number

Mobile country code

International number prefix 00

Mobile network code

National prefix 0

Step3: ADD VLRCFG ( Add local VLR information)

Mobile country code

Mobile network code

MSRN/HON allocation mode MSC

Step4: ADD SCCPSSN ( Add sub system)

SCMG

MSC

VLR

CAP

OPC: DPC:

28



SCMG

Contents

BSSAP

OPC: DPC:

Step5: ADD SCCPGT ( Add local office global title) GT address information

Translation result type

SPC

LSPC2(SPC)

Step6: ADD NACODE ( Add national code)

Mobile national access code All of the access code of local country

Step7: ADD MHPREFIX ( Add the prefix of roaming number)

MSRN/HON prefix ID

MSRN/HON prefix MSC NO.

MSRN/HON suffix length 3

Step8: ADD MHSUFFIX ( Add the suffix of roaming number)

MSRN/HON prefix ID

Start suffix 0

End suffix 999

MSRN/HON number type MSRN/HON

Task 2 : Check the data of SCCP layer Step 1 DSP SCCPSSN , Sub-system status should be “Allow” Confidential Information of Huawei. No Spreading without Permission

.29


Sub-system status = Allow Standby sub-system status = Prohibit CSCC Wait Agree Flag = FALSE Test Flag = FALSE Ignore SST Flag = FALSE

Step 2 TST SCCPGT,the translation result of spc should be correct:

Test Result of GT code ---------------------GT Index = 3 GT Matching Length = 7 GT Matching Content = 04001204022111 Translating Result Type = SPC NI = National Network SPC = bbb

30



Contents

MSOFTX3000 Interworking with HLR Configuration 1.Objectives Knowledge title

Requirement

MAP related concepts and function of C/D interface

Know

Data configuration for interworking with HLR

Master


Configue Signaling Transport Data


.31



Configure signaling related data: M3UA data

SPC of local entity

Local entity type AS

SPC of destination entity

Destination entity type AS

Traffic mode

Work mode

loadshare

IPSP

Destination entity index

Linkset index

Index of HLR (Refer to ADD M3DE)

WBSG module number

Local IP

Local port

Peer IP

Refer to “ADD BRD”

Task2

Check signaling related data: M3UA data !

32

"# $ !

%


Peer port


Contents

%%DSP M3LKS: LSX=0;%% RETCODE = 0 Operation succeeded M3UA LinkSet Title -----------------M3UA LinkSet Status = Active

!

"# $ !

%

%%DSP M3LNK: MN=211, M3LNK=0;%% RETCODE = 0 Operation succeeded M3UA Link Status ---------------Module Number = 211 Link Number = 0 SCTP Association ID = 6 Lock Information = Unlocked Local Inactive Info = Not deactivated manually Local Release Info = Not released manually Link Congestion Info = Not Congested Real In Stream Num = 16 Real Out Stream Num = 16 SLS CODE = 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F Status = Link Active.

Task 3 : Configure data of SCCP layer ADD SCCPDSP

ADD SCCPSSN

SCMG

HLR

OPC: DPC:

ADD IMSIGT

MCC+MNC

CC+NDC

ADD SCCPGT (IMSI)


.33


Number Plan

GT Address

HLR SPC

ISDNMOV

ADD SCCPGT (MSISDN)

Number Plan

GT Address

HLR SPC

ISDN

ADD SCCPGT (HLR) Number Plan

GT Address

HLR SPC

ISDN

Task 4 : Check the data of SCCP layer DSP SCCPDSP , the normal DPC status should be “Allow”

DPC Status = Allow Standby DPC status = Prohibit SCCP status = Allow Congestion Status = Not Congested

DSP SCCPSSN , Sub-system status should be “Allow” Sub-system status = Allow Standby sub-system status = Prohibit CSCC Wait Agree Flag = FALSE Test Flag = FALSE 34



Contents

Ignore SST Flag = FALSE

TST SCCPGT,the translation result of spc should be correct:



.35


MSOFTX3000 Interworking with BSC Configuration 1.Objectives Knowledge title

Requirement

MSOFTX3000 signaling configuration interworking with BSC

Master

MSOFTX3000 traffic configuration interworking with BSC

Master

The concepts of TID

CIC

Start Circuit and End Circuit

Comprehend


36

Configue Basic Mobile Service Data



Contents

3.Exercise in lab (Practice M3UA) Task1


SPC of local entity


&

'(


Destination entity type SG

& ) SPC of destination entity

( Destination entity type SP

Traffic mode

Work mode

loadshare

ASP

&

'(


Linkset index

Index of SG (Refer to ADD M3DE)

& )

(


Linkset index

Index of BSC (Refer to ADD M3DE) Confidential Information of Huawei. No Spreading without Permission

.37


WBSG module number

Local IP

Local port

Peer IP

Peer port


Task2


"# $ !

%

%%DSP M3LKS: LSX=0;%% RETCODE = 0 Operation succeeded M3UA LinkSet Title -----------------M3UA LinkSet Status = Active

!

"# $ !

%


Task 3 : Configure data of SCCP layer ADD SCCPDSP OPC:

SPC:

ADD SCCPSSN

SCMG

BSSAP

OPC: DPC:

38



Contents

Task 4 : Check the data of SCCP layer *

"# $

+%


Sub-system status = Allow Standby sub-system status = Prohibit CSCC Wait Agree Flag = FALSE Test Flag = FALSE Ignore SST Flag = FALSE

Task 5 : Configure the data of A interface: ADD CALLSRC Call source code

RSSC

ADD OFC


.39


Peer office type

Peer office level

Peer office attribute

BSC

low

BSC

DPC1

ADD BSC (Add BSC information to local office)

DPC

Home module NO

LAI

WCSU or WCCU

ADD LAIGCI (Configure LAI) GCI

MSC NO

LA Category

BSC DPC

LAI

ADD LAIGCI (Configure GCI) GCI

MSC NO

LA Category

BSC DPC

GCI

ADD RANMGW (Configure the relationship between BSC and MGW)

ADD ACPOOL (Configure the capability of A interface)

ADD AIETG OPC

DPC

ADD AIETKC SC

EC

Start CIC

TID

MOD AIETKC 40



SC

Contents

EC

Circuit state UNAVAILABLE

Task 6 : Operate the circuit status of A interface: ,

!- -

"# $"

%.

Result of operating circuit --------------------------Line type Module number Channel number Status

BSSAP

22

128

Uninstall

BSSAP

22

129

Idle

BSSAP

22

130

Idle

,

- **

"

RST AIETKC

- **

"

)

,

- **

"

,

- **

"

,

- **

"

)

"

-

-- .

-- . # -/ # -/ # -/

-- . -- . -- .


.41


MSOFTX3000 Interworking with PSTN 1.Objectives Knowledge title

Requirement

Different networking between MSOFTX3000 and PSTN

Know

The principle and applied protocol of networking between MSOFTX3000 and PSTN

Master

MSOFTX3000 interworking with PSTN configuration

Master


42

Configue Signaling Transport Data



Contents

3.Exercise in lab (Practice M2UA) Task1

Configure Embeded SG ADD ESG ADD M2LKS !

"

"#$#%

ADD M2LNK

Local IP

Local Port

Peer IP

Peer Port

Task 2 : Configure data of MTP layer ADD N7DSP OPC:

DPC:

ADD N7LKS ADD N7RT ADD N7LNK

Link Type

Start circuit no

SLC

SLC Send

M2UA 64K

Task 3 : Check the data of M2UA layer DSP M2LNK ,the statue of M2UA link should be “Active”

Link Number = 0 Link Congestion Info = Not Congested Link State = M2UA Link is Active. Confidential Information of Huawei. No Spreading without Permission

.43


SCTP Association ID = 5 Real In Stream Num = 16 Real Out Stream Num = 16 Local Inactive Info = Link Not Inactivated Manually Link Release Info = Link Not Released Manually

Task 4 : Check the data of MTP layer DSP N7DSP ,the state of DSP should be “Accessible”

Network Indicator = Nation Reserved Network DPC = 0001d3 OPC = 000143 Accessibility = Accessible Congestion Info = Not Congested DSP N7RT , the state of route should be “Healthy”

Route Information = Healthy Transfer Allowed In Service Rechoose Route Out Of Control SLS Code(Hex)

= 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

DSP N7LNK , the state of link should be “In use , Healthy”

Status = In Use, Healthy, Not Blocked, Activated, Not Locally Inhibited, Not Remotely Inhibited, Not Congested, 44



Contents

Not Swapping Over, Not Swapping Back. SLS Code(Hex) = 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

Task 5 Configure voice related data

Cal l source code

Route selection source code

01 Peer office type

Peer office level


PBX

low

PSTN

Route type

Sub-route selection mode

Ordinary route

Select by percentage

RSC

RSSC

Refer to “ADD CNACLD”

Refer to “ADD CALLSRC”

Route number

Signaling priority Prefer to select ISUP

2'

2 Confidential Information of Huawei. No Spreading without Permission

.45


#

%$&'(

Start circuit no

End circuit no

Circuit status Unavailable

Task 6 Operate the trunk circuit: 2

!

2

" # $," %

%%DSP N7TKC: MN=22, DT=ISUP, DR=SELF, SCN=32, ECN=34;%% RETCODE = 0 Operation succeeded Query ISUP circuit -----------------Device type Module number Circuit number CIC Value ISUP 22 32 1 ured to other ISUP 22 33 2 ISUP 22 34 3

RST N7TKC

- **

"

SRS N7TKC

- **

"

)

2

- **

"

)

2

- **

"

)

2

- **

"

2

- **

"

2 * /

46

- ** --

"

Circuit status Uninstalled

Reason Config

Idle Idle

/- - . /- - . # -/

/- - .

# -/

/- - .

# -/

/- - .

# -/ "

/- - .

# -/ 3

"

/- '4


-

.


Contents

MSOFTX3000 Interworking with MSC Server 1. Objectives Knowledge title

Requirement

The principle and applied protocol of networking between MSOFTX3000 and MSC Server

Know

MSOFTX3000 interworking with MSC Server configuration

Master

2. Reference Product CD MSOFTX3000 Configuration Guide

Configue Signaling Control Data


.47




SPC of local entity



Destination entity type AS

Traffic mode

Work mode

loadshare

IPSP


Linkset index

Index of MSCServer (Refer to ADD M3DE)

WBSG module number

Local IP

Local port

Peer IP


Task2


"# $ !

%

%%DSP M3LKS: LSX=0;%% RETCODE = 0 Operation succeeded

48


Peer port


Contents

M3UA LinkSet Title -----------------M3UA LinkSet Status = Active

!

"# $ !

%


Task 3 : Configure data of SCCP layer ADD SCCPDSP

ADD SCCPSSN

SCMG

VLR

MSC

OPC: DPC:

ADD SCCPGT (MSCServer) Number Plan

GT Address

MSC Server SPC

ISDN


.49


Task 4 : Check the data of SCCP layer DSP SCCPDSP , the normal DPC status should be “Allow”


DSP SCCPSSN , Sub-system status should be “Allow” Sub-system status = Allow Standby sub-system status = Prohibit CSCC Wait Agree Flag = FALSE Test Flag = FALSE Ignore SST Flag = FALSE

TST SCCPGT,the translation result of spc should be correct:


50



Contents

Task 5 : Configure voice related data

Cal l source code

Route selection source code

01 Peer office type

Peer office level


MSC

same

PSTN

Route type

Sub-route selection mode

Ordinary route

Select by percentage

RSC

RSSC

Refer to “ADD CNACLD”

Refer to “ADD CALLSRC”

), MGW

Signaling Type M3UA

Route number

Signaling priority Prefer to BICC_IP

select

' Circuit Type BICC_IP

), OFC

, Start CIC


.51


Task 6 Operate the BICC circuit: ),

,

!

),

,

" # $," %

+++ HW-MSOFTX 2006-05-10 14:32:18 O&M #833 %%DSP BICCCIC: OFNO=3, SCIC=0, ECIC=2;%% RETCODE = 0 Operation succeeded Query BICC CIC Result --------------------CIC Number CIC Status 0 No Blocking(Active), Idle 1 No Blocking(Active), Idle 2 No Blocking(Active), Idle (Result number = 3) --END

52

RST BICCCIC

- **

"

)

),

,

- **

"

) ),

,

- **

"

# -/ # -/

),

-- .

),

-- .

),

-- .



Contents

MSOFTX3000 Number Analysis Configuration 1.Objectives Knowledge title Related concepts to number analysis Number analysis procedure Configuration of PSTN/MSISDN/Local office playing tone/failure handling

Requirement Know Comprehend Master

Task 117 playing tone

failure playing tone

MS serves as calling part or called part Number conversion


Configue Basic Number Analysis Data


.53



Complete data configuration to make a call from MS to 117 for time announcement.

Call prefix

Called number type

DN processing flag

117

MSRN

True

Call prefix

Tone playing mode

Tone type

117

SDT(Play tone)

Time announcement

15

Task2

Task3

54

0

Complete data configuration to make a call from MS to MS of local office

Call prefix

Called number type

MSISDN prefix

MSISDN

Call prefix

Called number type

MSRN prefix

MSRN

Complete data configuration to make a call from MS to PSTN

Call prefix

Called number type

ISDN prefix

PSTN

RSC



Contents

Appendix A: Parameter referencing relationship 1.Part 1 Hardware

2.Part 2 Mc interface


.55


3.Part 3 Local office

56



Contents

4.Part 4 MTP layer


.57


5.Part 5 SCCP layer

58



Contents

6.Part 6 M2UA layer


.59


7.Part 7 M3UA layer

60



Contents

8.Part 8 Remote office


.61


9.Part 9 A interface

10.Part 10 Trunk

62



Contents

Appendix B: Common used Commands ( ))

*+ !

HARDWARE DATA ADD SHF

To add a shelf

RMV SHF

To remove a shelf

MOD SHF

To modify a shelf

LST SHF

To list a shelf

ADD FRM

To add a subrack

RMV FRM

To remove a subrack

MOD FRM

To modify a subrack

LST FRM

To list a subrack

ADD BRD

To add a board

RMV BRD

To remove a board

LST BRD

To query a board

MOD CPCCFG

To modify CPC link configuration

LST CPCCFG

To list CPC link configuration

ADD FECFG

To add FE port configuration

ADD CDBFUNC

To add CDB function configuration

ADD EPICFG

To add WEPI E1 configuration

ADD BOSRC

To add board clock reference source

SET CKICFG

To set WCKI clock configuration

SET CLKSRC

To set a clock reference source of WEPI

LOCAL OFFICE DATA SET OFI

Set local office information.

ADD NCODE

Add a country or region code (optional).

ADD ACODE

Add a national area code (optional).

ADD MASI

Add a multi-area statistics index (optional).

ADD MARLATION

Add a multi area relation (optional).

ADD CALLSRC

Add a call source code.

SET INOFFMSC

Set local mobile office information.

ADD NACODE

Add a mobile national access code. Confidential Information of Huawei. No Spreading without Permission

.63


ADD VLRCFG

Add VLR configuration (only when the MSOFTX3000serves as a VMSC).

ADD MHPREFIX

Add a prefix of the MSRN/HON number.

ADD MHSUFFIX

Add a suffix of the MSRN/HON number.

ADD IMHSUFFIX

Add a suffix of the internal MSRN/HON number. (reserved)

ADD MHLAICFG

Add a mapping relation between the LAI number and the MSRN/HON number. (optional)

ADD MHMSCCFG

Add a mapping relation between the MSC number and the MSRN/HON number. (optional)

Mc INTERFACE DATA ADD MGW

Add Media Gateway.

ADD H248LNK

Add H.248 link.

M2UA DATA ADD ESG

Add an embedded SG.

ADD M2LKS

Add an M2UA linkset.

ADD M2LNK

Add an M2UA link.

M3UA DATA ADD M3LE

Add an M3UA local entity.

ADD M3DE

Add an M3UA destination entity.

ADD M3DS

Add an M3UA additional destination service (optional).

ADD M3LKS

Add an M3UA linkset.

ADD M3LNK

Add an M3UA link.

ADD M3RT

Add an M3UA route.

MTP DATA ADD N7DSP

Add a MTP destination signaling point.

ADD N7LKS

Add a MTP linkset.

ADD N7LNK

Add a MTP link.

ADD N7RT

Add a MTP route.

SCCP DATA ADD SCCPDSP

Add SCCP destination signaling point (DSP).

ADD SCCPLDSH

Add SCCP destination signaling load share point (optional).

64



Contents

ADD SCCPADDR

Add originating address format translation (optional).

ADD SCCPSSN

Add SCCP sub-system number.

ADD SCCPGT

Add SCCP global title.

ADD IMSIGT

Add IMSI GT translation information

MAP SET MAPACCFG

Set MAP feature configuration.

SET MAPPARA

Set MAP feature parameter.

ADD MAPIFNP

Add MAP interface number change (optional).

OFFICE DATA ADD OFC

Add an office direction.

ADD SRT

Add a sub-route.

ADD RT

Add a route.

ADD TMIDX

Add a time index (optional).

ADD RTANA

Add a route analysis.

ADD N7TG

Add an SS7 trunk group.

ADD N7TKC

Add an SS7 trunk circuit.

A INTERFACE DATA ADD ACPOOL

Add an A-interface circuit pool.

ADD AIETG

Add an A-interface trunk group.

ADD AIETKC

Add an A-interface trunk circuit.

ADD RANMGW

Add radio access network media gateway.

ADD BSC

Add BSC

ADD LAIGCI

Add 2G LAI or GCI information.

NUMBER ANALYSIS DATA ADD DNC

Add a number change.

ADD SRVCHK

Add a service check.

ADD CNACLD

Add a call prefix.

ADD CLDPREANA

Add called number pre-analysis.

ADD SUPERRT

Add enhanced route processing.

ADD AUSSIG

Add auxiliary signaling.

ADD PFXPRO

Add call prefix processing.


.65


ADD IMSIBITANA

Add IMSI number analysis

ADD CLICRTPRO

Add caller feature processing

ADD CLICRTANA

Add caller feature analysis

ADD CNACLR

Add caller number analysis

ADD CLCRPRO

Add CLIP called number correlation processing

ADD CLIPRO

Add CLIP processing

ADD INCLRIDX

Add incoming caller number associated processing(optional)

ADD INORICLDIDX

Add incoming original called number associated processing(optional)

ADD INNUMPREPRO

Add incoming number pre-processing

ADD OUTCLRIDX

Add outgoing caller number associated processing(optional)

ADD OUTORICLDIDX

Add outgoing original called number associated processing (optional)

ADD OUTNUMPREPRO

Add outgoing number pre-processing

ADD PRICHKORICLDIDX

Add original called number associated processing (optional).

ADD CALLPRICHK

Add call authority check.

ADD ROAMUSRT

Add a roaming subscriber type.

ADD USROAMRT

Add subscriber group roaming authority. (optional)

66


73311424 MSOFTX3000 Engineering Training Practice Guide

Recommend Documents