This is Disrol 300 marine engine oil specially develop by PETRONAS for the application in the marine engine
fault tracing
This very good product produced by PETRONAS for the application of marine engine
good research work
Full description
AP18.00-S-0101A Engine oil and filter change ENGINES 104.900 in MODEL 638 ENGINES 111.948 /950 /978 /980 in MODEL 638 ENGINES 601.942 /970 in MODEL 638 ENGINES 611.980 in MODEL 638 ENGINES 112.951 /976 in MODEL 639 ENGINES 272.978 in MODEL 639 ENGINES 646.980 /981 /982 /983 in MODEL 639 ENGINES 642.990 in MODEL 639
Value modified: Oil drain screw to oil pan Value modified: Oil drain screw to oil pan
e
Removing
a Danger!
Risk of death caused by vehicle slipping or toppling off of the lifting platform.
a Danger!
Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running Replace oil filter element (4)
1
2.1
Pull out the dipstick (1) and suck out engine oil over the oil dipstick guide tube
Engine 611.980
*BA01.45-N-1003-01A *BA01.45-N-1003-01H
Align vehicle between columns of vehicle lift AS00.00-Z-0010-01A and position four support plates at vehicle lift support points specified by vehicle manufacturer. Secure vehicle to prevent it from moving by AS00.00-Z-0005-01A itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. Engine 104.900 in model 638.244 /294 Engines 111, 112, 272.978 Engines 601, 611, 642.990, 646 Only when extracting the engine oil
Copyright Daimler AG 11/28/11 G/06/08. This WIS printout will not be recorded by the update service.
i Extract engine oil only when the engine is at normal operating temperature. For engine oil extractor see GOTIS http://gotis.aftersales.daimlerchrysler.com 2.2
Drain engine oil at oil drain screw (3) of oil pan
Only when draining engine oil i Only drain engine oil when engine is at normal operating temperature. i On model 638 with engine 111 and on model 639.701/703/705/711/713/811/813/ 815 as of vehicle identification number 055347 the bottom engine compartment paneling is to be removed, see: @
Model 638 with engine 111 Remove/install bottom engine compartment paneling Model 639.701/703/705/711/713/811/813/ 815 as of vehicle identification number 055347 Remove/install bottom engine compartment paneling
f
f d 3
AR61.20-S-1105A
AR61.20-S-1105S
Install Screw in oil drain screw (3) and tighten fully. p Replace sealing ring for oil drain screw (3) to avoid any leakages. Engine 104.900 Oil drain screw to oil pan n Engine 111 n Oil drain screw to oil pan
*BA01.45-N-1002-01E
*BA01.45-N-1003-01A
Engine 112 n Oil drain screw to oil pan M14 Engine 272 Oil drain screw to oil pan n ENGINES 601, 611, 646 Oil drain screw to oil pan n Engine 642 n Oil drain screw to oil pan 4
Check oil filter cover (7) and if necessary, oil i On model 638 with engine 111 and on drain screw (3) or oil drain screw for oil filter model 639.701/703/705/711/713/811/813/ (6) for leaks 815 as of vehicle identification number 055347 the bottom engine compartment paneling is to be removed, see:
p The oil level must on no account lie higher than the maximum marking, as this may result in damage to the engine. i Do not check oil level until approx. 2 min after switching off the engine. i The fill level markings on the oil dipstick (1) are designed for an engine oil temperature of approx. 80 °C. Do not top up with any more oil for engine oil temperatures below this when filling the prescribed oil quantity.
