Mecanismo Biela-Manivela hecho en matlab para desplazamientos, velocidades y aceleraciones
Descripción: MANUAL DE PARTES CATERPILLAR 3306
ResumenDescripción completa
Deskripsi lengkap
Descripción: caterpillar
Descripción completa
Descripción completa
5/21 5/21/1 /13 3
3306 3306 DI Engine Engine Emissions Emissions Retrofit Retrofit Repow Repower er Tier I For 140G 140G Motor Motor Grader Grader 13W00 13W0000 001-UP 1-UP (MACHINE)(SEBP5 (MACHINE)(SEBP530 308 8 - 05) - Sistem Sistemas y compo compone nente ntes s
Cerrar SIS Pantalla anterior Producto: MOTOR GRADER Modelo: 140G MOTOR GRADER 13W Configuración: 3306 DI Engine Emissions R etrofit Repo wer Tier I For 140G Motor Grader 13W00 001-UP (MACHINE) (MACHINE)
Especificaciones 3306 VEHICULAR ENGINE Númer mero de de med mediio -S -SENR7592-01 -01
Fec Fecha de de pu publicac cación -01 -01/07 /07/19 /1981
Fec Fecha de de act actu uali alizaci ación -18 -18/07/2003 SENR75920056
Connecti Conn ecting ng Rod
(1) Bore in bearing for piston pin (new): 5S6360 Rod ... 1.5017 ± .0003 in.(38.143 ± 0.008 mm) 5S2793 Rod ... 1.7012 ± .0003 in.(43.210 ± 0.008 mm) 8N1721 & 8N1984 Rod (tapered) ... 1.7012 ± .0003 in.(43.210 ± 0.008 mm) Maximum permissible clearance between bearing and piston pin (worn) ... .003 in.(0.08 mm) (2) Bore in connecting rod for bearing ... 3.2500 ± .0005 in.(82.550 ± 0.013 mm) (3) Distance between center of piston pin and center of crankshaft bearing (new) ... 9.595 ± .001 in.(243.71 ± 0.03 0.0 3 mm) https://10.144.4 https://10.144.4.9:84 .9:8443/sisweb/sisweb/te 43/sisweb/sisweb/techdoc/techdo chdoc/techdoc_pri c_print_pa nt_pag g e.jsp?returnurl= e.jsp?returnur l= /sisweb /sis web/sis /sisweb web/productsearch/productheade /productsearch/productheaderi ri nfoframeset.jsp&call nfoframeset.jsp&call edpag edpag e=/sis… e=/si s…
1/3
5/21/13
3306 DI Engine Emissions Retrofit Repower Tier I For 140G Motor Grader 13W00001-UP (MACHINE)(SEBP5308 - 05) - Sistemas y componentes
(4) Diameter of piston pin (new): 9H4016 Pin ... 1.5003 ± .0002 in.(38.108 ± 0.005 mm) 7N9804 Pin ... 1.5003 ± .0002 in.(38.108 ± 0.005 mm) 8M6487 Pin ... 1.6998 ± .0002 in.(43.175 ± 0.005 mm) 7N9805 Pin ... 1.6998 ± .0002 in.(43.175 ± 0.005 mm) (5) Clearance between connecting rod bearing and crankshaft bearing surface (journal) ... .0030 to .0066 in. (0.076 to 0.168 mm) Maximum permissible clearance between bearing and crankshaft (worn) ... .010 in.(0.25 mm) (6) Torque on nut for connecting rod: a. Put engine oil on threads and nut seat. b. Tighten both nuts to ... 30 ± 3 lb. ft.(40 ± 4 N·m) c. Mark each nut and end of bolt. d. Again tighten both nuts (from mark) ... 90°
Install the connecting rod in the piston with the slot for the bearing tab on the same side as the V mark on the piston. Make reference to Special Instructions, Form No. GMG02394 and SMHS7366 for information about checking and reconditioning connecting rods.
