CISCO INTRODUCCION A PACKET TRACERDescripción completa
Descripción: packet tracer
Descripción completa
Penjelasan tentang bagaimana cara mengopersikan aplikasi Packet Tracer yang baik dan benarDeskripsi lengkap
Descrição completa
Descripción completa
Packet Tracer 4.4.1.2 CCNA3
Full description
Descripción completa
Latihan Cisco Packet Tracer
Descripción: Manual Packet Tracer 6
Descripción: Tercera Clase Packet Tracer
Descripción: Packet Tracer 4.4.1.2 CCNA3
Descripción: prueba
ghghghghFull description
Student Packet Tracer Manual CISCO
ciscoFull description
Packet Tracer – Home IoT Implementation Scenario In this Packet Tracer scenario, Bob has begun to implement an IoT solution in his home. You will explore the variety of devices and manipulate environmental factors to s ee the impact on sensors and actuators. You will also configure some basic settings, including IP addressing for a sensor, and security settings for the gateway router. Finally, you will verify that all the devices in the home have IP connectivity.
Part Part 1: Conn ectin g Devices to the Home Gate Gateway way Step 1: Config ure Home Gateway. a.
Click Home to expand the cluster.
b.
Click Home Gateway . Click Config tab.
c.
Click Internet . Select DHCP for IP Configuration.
d.
Click Wireless. Enter MyHomeGateway as the SSID. Select WPA2-PSK as the authentication. Enter CiscoIoT as the PSK Pass Phrase.
e.
Click Home PC. Click Desktop . Click IP Configuratio n . Select DHCP for IP Configuration.
Step Step 2: Verify Home Gateway Gateway connectivi ty t o regist ration s erver. erver. a. From Home PC, enter www.register.pka in the Web W eb Browser. Enter admin as the Username and admin as the Password to log in to the remote registration server. Note: It may take a few minutes for all the IoT devices to be listed.
List some of the IoT devices: What are some available actions for these IoT devices?
b. From Home PC, enter 192.168.25.1 in the Web Browser. Enter admin as the Username and admin as the Password to log into the local IoT server hosted on Home Gateway . List some of the IoT devices: What are some available actions for these IoT devices?
Part Part 2: Interactin g with wi th IoT Devices Devices Step Step 1: Aut omate temperature control . Currently the Thermostat is off. Set the Thermostat to automatically adjust to the desired setting. a.
Au to . Enter the desired auto heating and auto cooling Expand the Thermostat status bar. Click Auto temperatures and click Set .
b.
Heating Element Element and Cooling Element Element as they adjust the temperature. Observe the Heating
Step 2: Automate the Ceiling Fan. The Ceiling Fan is configured to turn on onl y when motion is detected and no wind detected. The SBC0 with the use of motion and wind sensors controls the status of the ceiling fan. Al t + Cli ck the Motion Sensor near the Ceiling Fan . This will activate the Motion Sensor .
Did the Ceiling Fan turn on?
Step 3: Aut omate Lawn Sprinkl ers. Watering the lawn could be an activity controlled through conditional statements configured in the local IoT server on Home Gateway . a.
Expand the status for Lawn Sprinkler , Lawn Sprinkler0, and Water Level Monit or . Observe the relationship between the water level and the status of the lawn sprinklers. What condition triggers the lawn sprinklers to turn on?
What condition triggers the lawn sprinklers to turn off?
b.
Click Conditions at the top of the webpage. Locate the conditional statements. How many conditional statements control the lawn sprinklers?
Step 4: Aut omate Web Camera. The Web Camera is currently configured to only turn on when the Motion Detector is triggered. a.
Expand the status for Motion Detector and Web Camera. Observe the relationship between the Motion Detector and the status of the Web Camera.
b. Al t + Cli ck Moti on Detec to r in the topology. Make sure to click the one near the Webcam. What did you see on Webcam in the webpage?
Step 5: Open Windows and Garage Door. An old car is being repaired in the garage. A CO detector, garage door, and windows have been installed and configured to prevent CO poisoning. a.
Expand the status for all the windows, Garage Door , and the Garage CO Detect or . Are any devices missing from the list?
b.
For the unconnected device, verify that it is configured to connect to the Home Gateway for the IoE Server, and that DHCP is enabled for the IP Configuration settings.
c.
Start the old car by Al t + Cli ck the Car in the garage and watch the CO l evel rise in the garage.
d. Al t + Cli ck the Car to turn off the old car. e.
Observe how the windows and garage door interact with the CO level in the garage.
Packet Tracer – Home IoT Implementation Scenario In this Packet Tracer scenario, Bob has begun to implement an IoT solution in his home. You will explore the variety of devices and manipulate environmental factors to s ee the impact on sensors and actuators. You will also configure some basic settings, including IP addressing for a sensor, and security settings for the gateway router. Finally, you will verify that all the devices in the home have IP connectivity.
Part Part 1: Conn ectin g Devices to the Home Gate Gateway way Step 1: Config ure Home Gateway. a.
Click Home to expand the cluster.
b.
Click Home Gateway . Click Config tab.
c.
Click Internet . Select DHCP for IP Configuration.
d.
Click Wireless. Enter MyHomeGateway as the SSID. Select WPA2-PSK as the authentication. Enter CiscoIoT as the PSK Pass Phrase.
e.
Click Home PC. Click Desktop . Click IP Configuratio n . Select DHCP for IP Configuration.
Step Step 2: Verify Home Gateway Gateway connectivi ty t o regist ration s erver. erver. a. From Home PC, enter www.register.pka in the Web W eb Browser. Enter admin as the Username and admin as the Password to log in to the remote registration server. Note: It may take a few minutes for all the IoT devices to be listed.
List some of the IoT devices: What are some available actions for these IoT devices?
b. From Home PC, enter 192.168.25.1 in the Web Browser. Enter admin as the Username and admin as the Password to log into the local IoT server hosted on Home Gateway . List some of the IoT devices: What are some available actions for these IoT devices?
Part Part 2: Interactin g with wi th IoT Devices Devices Step Step 1: Aut omate temperature control . Currently the Thermostat is off. Set the Thermostat to automatically adjust to the desired setting. a.
Au to . Enter the desired auto heating and auto cooling Expand the Thermostat status bar. Click Auto temperatures and click Set .
b.
Heating Element Element and Cooling Element Element as they adjust the temperature. Observe the Heating
