298233143-FSME-D-to-FSMF-Replacement-Procedure-TS-SRAN-SW-188-I7.pdf

Technical Support Note TS-3GBTS-SW-188

FSME/D to FSMF replacement procedure Radio Networks Flexi Multiradio BTS WCDMA A p p r o v a l d a t e : ( 1 7 - S e p - 2 0 1 4 )

This document contains following type of information Informative

X

Preventive Corrective Additional categorization

Urgent Security Release Upgrade SW Update Parameterization Information is classified as

Internal Public

X

Customer Specific

Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their components. If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia Solutions and N etworks for additional information.

TS-3GBTS-SW-18 8 - Page 1/52 TS-3GBTS-SW-188 Version 7.0 Confidential

© Nokia Solutions and Networks 2014

Table of Contents 1. 2. 3. 4. 5. 6.

Validity..................... Validity.... .................................. ................................. ................................. ................................. ................................ ................................ ................................. ................... 5 Terminolo Termi nology.... gy..................... .................................. ................................. ................................. ................................. ................................. ................................. ......................... ......... 5 Compatib Comp atibili ility ty .............. ............................... .................................. ................................. ................................. ................................. ................................. ............................... .............. 5 Keywords Keyw ords ................ ................................. ................................. ................................. ................................. ................................ ................................ ................................. ................... 5 Introducti Intro duction on ............... ................................ .................................. ................................. ................................. ................................. ................................. ............................... .............. 5 SW mana managemen gementt ............... ................................ .................................. ................................. ................................. .................................. ................................. ...................... ...... 6 6.1 .....FSMF factory load SW........................................................................................................... 6 6.2 .....SW update – update – New New,, out of of box FSMF......... .................. ................... ................... .................. ................... ................... ................... ................... ........... .. 7 6.3 .....SW update – update – Used FSMF ................... .................................... ................................. ................................ ................................ ................................. ................... 7 6.4 .....SW updates from WN8.0 2.1 to WN8.0 3.1 and later ............................................................. 8 7. Instr Instructio uctions ns ................ ................................. .................................. ................................. ................................. ................................. ................................ ............................... ............... 9 7.1 .....Time requ required ired .............. ............................... .................................. ................................. ................................. .................................. ................................. ...................... ...... 9 7.2 .....Prep Preparati arations ons ................ ................................. .................................. ................................. ................................. .................................. ................................. ...................... ...... 9 7.3 .....Steps prior to site visit ......................................................................................................... 10 7.4 .....Steps during to site visit ......... .................. ................... ................... .................. ................... ................... ................... ................... ................... ................... ......... 25 7.5 ..... Additional Additional information information ........ .................. ................... ................... ................... ................... ................... ................... ................... ................... ................... ............ ... 46 7.5.1 FSMF sub-modules ....................................................................... 46 7.5.2 FSMF synchronization cables ....................................................... 46 7.5.3 FSMF GPS feeding cables ............................................................ 46 7.5.4 FSMF EAC cables ......................................................................... 47 7.5.5 FSMF EAC signal and pin assignment .......................................... 47 7.5.6 Radio modules with 6 GB RP3-01 link speed support ................ ... 48 7.5.7 SFP modules for 6 GB RP3-01 link speed......... .................. ................... ................... ......... 48 7.5.8 SFP modules for 3 GB RP3-01 link speed ......... .................. ................... ................... ......... 48 7.5.9 FSMF interfaces ............................................................................ 49 7.5.10 FSMF LMP connector pin map ...................................................... 51 Contact: Contact your local Nokia Solutions and Networks support

Summary of changes: 03-Oct-2013 04-Nov-2013 12-Dec-2013 11-Feb-2014 24-Mar-2014 23-July-2014 17-Sep-2014


1.0 2.0 3.0 4.0 5.0 6.0 7.0

Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set.


Table of Contents 1. 2. 3. 4. 5. 6.

Validity..................... Validity.... .................................. ................................. ................................. ................................. ................................ ................................ ................................. ................... 5 Terminolo Termi nology.... gy..................... .................................. ................................. ................................. ................................. ................................. ................................. ......................... ......... 5 Compatib Comp atibili ility ty .............. ............................... .................................. ................................. ................................. ................................. ................................. ............................... .............. 5 Keywords Keyw ords ................ ................................. ................................. ................................. ................................. ................................ ................................ ................................. ................... 5 Introducti Intro duction on ............... ................................ .................................. ................................. ................................. ................................. ................................. ............................... .............. 5 SW mana managemen gementt ............... ................................ .................................. ................................. ................................. .................................. ................................. ...................... ...... 6 6.1 .....FSMF factory load SW........................................................................................................... 6 6.2 .....SW update – update – New New,, out of of box FSMF......... .................. ................... ................... .................. ................... ................... ................... ................... ........... .. 7 6.3 .....SW update – update – Used FSMF ................... .................................... ................................. ................................ ................................ ................................. ................... 7 6.4 .....SW updates from WN8.0 2.1 to WN8.0 3.1 and later ............................................................. 8 7. Instr Instructio uctions ns ................ ................................. .................................. ................................. ................................. ................................. ................................ ............................... ............... 9 7.1 .....Time requ required ired .............. ............................... .................................. ................................. ................................. .................................. ................................. ...................... ...... 9 7.2 .....Prep Preparati arations ons ................ ................................. .................................. ................................. ................................. .................................. ................................. ...................... ...... 9 7.3 .....Steps prior to site visit ......................................................................................................... 10 7.4 .....Steps during to site visit ......... .................. ................... ................... .................. ................... ................... ................... ................... ................... ................... ......... 25 7.5 ..... Additional Additional information information ........ .................. ................... ................... ................... ................... ................... ................... ................... ................... ................... ............ ... 46 7.5.1 FSMF sub-modules ....................................................................... 46 7.5.2 FSMF synchronization cables ....................................................... 46 7.5.3 FSMF GPS feeding cables ............................................................ 46 7.5.4 FSMF EAC cables ......................................................................... 47 7.5.5 FSMF EAC signal and pin assignment .......................................... 47 7.5.6 Radio modules with 6 GB RP3-01 link speed support ................ ... 48 7.5.7 SFP modules for 6 GB RP3-01 link speed......... .................. ................... ................... ......... 48 7.5.8 SFP modules for 3 GB RP3-01 link speed ......... .................. ................... ................... ......... 48 7.5.9 FSMF interfaces ............................................................................ 49 7.5.10 FSMF LMP connector pin map ...................................................... 51 Contact: Contact your local Nokia Solutions and Networks support

Summary of changes: 03-Oct-2013 04-Nov-2013 12-Dec-2013 11-Feb-2014 24-Mar-2014 23-July-2014 17-Sep-2014


1.0 2.0 3.0 4.0 5.0 6.0 7.0

Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set. Approved instruction set.


Changes between issues 1.0 and 2.0 Chapter 6 • Factory new FSMF information and recommended SW upgrade paths updated Chapter 7 Step 1.1, 7.1. FSME/D power distribution unit reuse with FSMF noted • • Step 5.5. CCCH processing set commissioning step clarified • Step 7.4. FPMA/battery backup commissioning step clarified • Step 10.1 in 2G-3G RF sharing, 2G BTS to be updated updated after 3G BTS commissioning Chapter 7.4.9 • FSMF front panel interface information added Chapter 7.4.10 • FSMF LMP connector pin out map added Changes between issues 2.0 and 3.0 Chapter 3 • SW compatibility information updated. Chapter 6 • Supported SW upgrade paths updated. Chapter 7 • Step 5.5. CCCH processing set License Key usage clarified. • Step 9.2, 9.3. FSME/D backup SCF conversion for FSMF use added. • Step 9.1. Planned commissioning instruction removed - Template commissioning is preferred. Chapter 7.2 Preparations updated • Changes between issues 3.0 and 4.0 Chapter 6.2, 6.3 • Supported RU30 SW upgrade paths updated for A.103 FSMF. Chapter 7.3 • Step 1.2 added details to regenerate WBTS licenses Chapter 7.4 • Step 5.6, 5.7, 5.8 and 9.5, 9.6, 9.7 added details when baseband capacity is changed from 2 x FSME to 1 x FSMF and when more than 6 cells with HSPA are present. • Step 9.1 added details when backup SCF from RU30/RU40 RU30/RU40 in template commissioning Changes between issues 4.0 and 5.0 Chapter 6.2 • Repaired A.102 FSMF BTS SW version updated. Chapter 7.2 • Material list updated to support external IP devices with FSMF Chapter 7.3 • Step 6.3. Site specific IP configuration is different between FSME/D and FSMF. Chapter 7.4 • Step 7.9. Support for external IP devices with FSMF • Step 9.2. Site specific IP configuration is different between FSME/D and FSMF. • Step 9.9. Antenna Line Settings – Settings – note note added for RealTilt commissioning



Changes between issues 5.0 and 6.0 Chapter 7.3 • Step 1.2 Clarified that FSMF support support feature RAN1849 BTS Licensing Logical Target ID Changes between issues 6.0 and 7.0 Chapter 6.1 • Added note to check PC firewall settings to allow successful software software download and commissioning file transfer to BTS. Chapter 6.4 • Added information of possible additional BTS reset required during SW upgrade upgrade from WN8.0 2.0 to WN8.0 3.1 and later. Chapter 7.3 • Step 4.1 Added note to check PC firewall settings. Chapter 7.4 • Step 9.9 Added note to check PC firewall settings.



Purpose The purpose of this TSN is to give instructions on how to replace the existing FSME/D Flexi Multiradio System module in WCDMA BTS Site with FSMF Flexi Multiradio System module.

1. VALIDITY Product

Product code

Core Module

Flexi Multiradio System Module, FSMD Flexi Multiradio System Module, FSME Flexi Multiradio System Module, FSMF

471402A 471469A 472181A System level RU40

083780A 083833A 084792A BTS Software WN8.0 2.0

Flexi Multiradio WCDMA BTS

2. TERMINOLOGY The following terminology is used in this document: FSMD FSME FSMF RFM FTIF FBBA FPFD

Flexi Multiradio System Module (rel 2) Flexi Multiradio System Module (rel 2) Flexi Multiradio System Module (rel 3) Flexi Multiradio RF module / Remote Radio head Transport sub-module Extension baseband sub-module Power distribution sub-module

3. COMPATIBILITY WCDMA BTS SW support for Flexi Multiradio System Module FSMF A.102 is available starting from WN7.0 3.0.1/WN8.0 2.0 and for Multiradio System Module FSMF A.103 starting from WN7.0 3.0/WN8.0 2.0.

4. KEYWORDS WN7.0 3.0, WN7.0 3.0.1, WN8.0 2.0, System module swap, System module replacement, WCDMA, FSMD, FSME, FSMF, A.102, A.103

5. INTRODUCTION This TSN gives the user guidelines and instructions on how to replace an existing FSMD/E System module with FSMF System module while maintaining the existing site functionality, features and capacity. The instructions will cover both dedicated 3G BTS as well as 3G-2G RF Sharing site scenarios. References to the existing Flexi Multiradio 10 BTS documentation are made (available in NOLS). WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03. Check WCDMA RAN, Rel. RU40, Operating Documentation Change Delivery sets for latest updates.



6. SW MANAGEMENT Out of box FSMF System module is delivered with so called ‘factory load SW’.

6.1 FSMF factory load SW All new FSMF version A.103 modules are delivered with preinstalled LN4.0 1.2 (LN4.0 ENB 1202_781_57) SW that has hardware security enabled (SW Verification Agent). Repaired FSMF version A.102 modules are also updated to same LN4.0 1.2 (LN4.0_ENB_1202_ 781_57) SW since week 11/2014. After this, FSMF version A.102 works exactly the same as FSMF A.103, including RAN2423 SW Verification agent (WCDMA) and LT E940 SW Verification agent (LTE/TD-LTE) features. Some FSMF A.102 modules delivered from NSN hubs may still contain older factory SW (LN4.0_ENB_1202_696_00). In this case it is recommended to check the possible SW upgrade options in reference documentation (chapter 8). RAN2423 SW Verification agent (WCDMA) and LTE940 SW Verification agent (LTE/TD-LTE) have been enabled in RU30/RU40/RL40/RL50/RL25/RL35 BTS SW’s and onwards. Therefore, SW versions listed in 6.2 are recommended to assure successful SW update. For further details, refer to TS-LTE_BTS_FDD-SW-0047 Severe issue - introduction of the LTE940 - SW Verification Agent and WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03, RAN2423: SW Verification Agent. BTS Site manager compatibility vs. FSMF factory load To complete LTE to WCDMA SW update there is no need to have compatible LTE BTS Site manager available as WCDMA BTS Site Manager can be used as well. While FSMF is initially running LTE SW and when using WCDMA BTS Site manager, the BTS Hardware view will be limited though and no modules can be displayed. However, SW update is possible from FSMF factory load (LTE) to RU30/RU40 BTS SW (WCDMA).

Figure 1: Incompatible BTS Site manager view If a firewall is installed on the PC, you may need to configure it to allow TCP ports 13062 – 13092 to accept incoming connections from the Flexi Multiradio BTS. This TCP port must be ‘open’ to enable FlexiBTS Site Manager software downloading and commissioning file transfer to BTS. For further information, contact your System Administrator or IT Helpdesk.

TS-3GBTS-SW-188 - Page 6/52 Version 7.0 Confidential


6.2 SW update – New, out of box FSMF FSMF A.102/A.103 with LTE BTS SW

Figure 2: Out of box FSMF SW update to WCDMA

6.3 SW update – Used FSMF FSMF A.102/A.103 used previously in LTE/TD-LTE

Figure 3: Used FSMF SW update to WCDMA



6.4 SW updates from WN8.0 2.1 to WN8.0 3.1 and later Once WN8.0 2.1 is activated to WCDMA BTS and further SW upgrade is planned to WN8.0 3.1 or later, in some cases BTS is requesting additional reset due to changed link speed validation functionality. When 3Gb link speed SFP’s are used on optical link between FSMF and RF modules / when RF module does not support 6Gb link speed, additional reset is not needed.



7. INSTRUCTIONS The instructions given in this section are used to prepare the FSMF system module for the site visit. References to the operating documentation (in NOLS) can be found in ‘Further details’ column.

7.1 Time required The total time needed for the entire swap depends on the site specific requirement and how much preparation was done in advance. There are many ways to implement FSMF swap, this approach is typical to make necessary changes with existing tools.

7.2 Preparations In order to minimize outage time during FSME/D to FSMF swap, it is recommended to perform certain activities in advance/remotely. However, all these steps can also be done while on site. Tools required   

T20 screwdriver for tightening grounding cables, front cover etc. T15 screwdriver / 3 mm hex tool for DC input cable tightening on FPFD 2,5 mm hex tool for DC out port cable tightening

Materials       

FSMF Flexi System Module Optional sub-modules (FTIF, FBBA, FPFD) needed on target site and front cover 48 VDC Power Supply, PC with LAN cable RU30/RU40 BTS SW and compatible BTS Site Manager GPS cable set, synchronization cable set, EAC cable set for FSMF Flexi System Module SFP modules for RFM’s supporting 6GB RP3-01 link speed 10/100Mb switch to support connection with external IP devices - Mandatory in case WHMC/RCUA is in use

Steps prior to site visit       

Backup of existing BTS commissioning file (Step 1) Integrate optional sub-modules with FSMF (Step 2) Install compatible WCDMA BTS Site manager (Step 3) SW upgrade to desired WCDMA BTS SW (Step 4) When firewall on the PC, configure it allow connections from Flexi BTS (Step 4.1). Conversion of existing BTS commissioning file for new FSMF System module (Step 5) Create TRS commissioning file manually derived from existing BTS (Step 6)

Note: Offline conversion of FSME/D TRS commissioning parameters is not supported for FSMF use (Step 6). Automatic conversion of FSME/D BTS and TRS commissioning parameters is supported when connected to FSMF (Template commissioning). Steps during site visit    

FSMF System module replacement, power feed and all cabling (Step 7) BTS SW upgrade (Step 8) BTS commissioning (Step 9) Update 2G BTS commissioning in RF sharing (Step 10)



7.3 Steps prior to site visit Step 1 1.1

Description

Expected result

Further details

Backup SCF and snapshot is stored to local directory.

Snapshot can be viewed with offline BTS Site manager while setting TRS parameters for FSMF commissioning.

When BTS pool license is exported from NetAct, it’s possible to regenerate it and import it to NetAct again as BTS pool license.

RAN2131 Automatic License Distribution to Flexi BTS When feature is not in use, BTS pool license cannot be transferred from NetAct to BTS in automatic way.

Save existing BTS data

- Establish remote BTS Site manager connection to the existing WCDMA BTS equipped with FSME/D module.

- Store 2 files: 1) Backup commissioning file, select ‘BTS’ as Target, ‘File -> Backup Commissioning Files…’ and save it to local directory. 2) Save Snapshot (select ‘Current data in BTS Site Manager ’ option to save time) and save it local directory.

WBTS licenses

1.2

As RAN1849 BTS Licensing Logical Target ID for Flexi BTS is valid for FSMF, no manual license installation / substitution process is needed if pre-conditions from RAN1849 are considered: -There must be 24 h break in between before the re-use of a FSM or FRM in another BTS -Not both – FSM and RF Modules must be replaced at the same time

Table 1: Activities prior to site visit



Step 2 2.1

Description

Expected result

Further details

- Equip FSMF with optional sub-modules according to the target BTS site requirements.

Sub-module installation and front cover preparation completed.

Note: FSME/D specific power distribution modules (FPFB) and interconnection plug-in card cannot be used with FSMF.

Time required: FPFD – 15 min FBBA – 3 min FTIF – 1 min

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02 Document Change Delivery 3 Flexi Multiradio 10 BTS Quick Guide

Install optional FSMF sub-modules

Do not mix FPFD and FTIF interconnection plug-in cards. FTIF interconnection plug-in card is labeled with ‘FSM’ and ‘TRS’. FPFD plug-in card is labeled with ‘Power unit FPFD’.

Total time used for installing sub-modules varies according each site requirements.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Installing Flexi Multiradio 10 Base Station for Stack, Wall, and Pole Configurations WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Cabling Flexi Multiradio 10 Base Station, Connecting Flexi Multiradio 10 BTS Capacity Extension Sub-Module (FBBA) cabling WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi Multiradio 10 BTS s ystem module capacity

Prepare front cover

2.2

- Check and prepare front cover .

Front cover preparation is complete.

With FMCA front cover version A.206 or older, remove inner air deflector plate to enhance airflow to FSMF unit and submodules.

TS-3GBTS-HW-0177 New Flexi 3U Mounting Covers Front and Back 470239A.207

On the new FMCA (470239A.207) Flexi 3U Mounting Covers Front/Back, the air deflector plate from inside of the Front Cover is removed.

Table 2: Activities prior to site visit (continued)



Step 3 3.1

Description

Expected result

Further details

Install BTS Site manager and prepare LAN connection

- Install compatible WCDMA BTS Site manager to PC.

BTS Site manager installation successfully completed.

- Connect Ethernet cable between FSMF LMP port and personal computer.

FSMF A.102 LTE factory load compatible BTS Site manager LN4.0_1202_759_00 is delivered with LN4.0 RL40 0.0.5 in NOLS. FSMF A.103 LTE factory load compatible BTS Site manager LN4.0_1202_765_02 is delivered with LN4.0 RL40 1.1.2 in NOLS.

Note: PC’s network port properties must be modified as follows: - Set IP address to 192.168.255.126 and subnet mask to 255.255.254.0. Specifying a default gateway is not required. 4 4.1

Power up FSMF and check running SW versions

- Connect power source to DC in port and power up FSMF. - Open WCDMA BTS Site manager and establish local connection with FSMF.

FSMF comes up and local BTS Site manager connection is established.

Note: New FSMF is running LTE technology based factory SW. To check running SW version, select Update SW to BTS Site and current BTS SW version is displayed.

6.1 FSMF factory SW If a firewall is installed on the PC, you may need to configure it to allow TCP ports 13062 – 13092 to accept incoming connections from the Flexi Multiradio BTS. This TCP port must be ‘open’ to enable Flexi BTS Site Manager software downloading. For further information about the specific firewall installed on your PC, contact your System Administrator or IT Helpdesk.

Update BTS SW

4.2

SW update path with factory new FSMF. Check SW compatibility and supported SW upgrade paths in chapter 6. - Download and activate WCDMA BTS SW on top of FSMF factory load/current SW load. Note: FSMF with factory load requires compatible LTE BTS Site manager in order to have detected HW modules displayed.

If FSMF is not updated to desired RU30/RU40 BTS SW, and LTE BTS Site manager is not available, no HW modules are displayed in BTS Site manager.

SW update successfully completed. Time required: FSMF only – approximately 15 min FSMF with RFM’s – approximately 18 - 20 min FSMF is ready for site installation.

In this case only RFM LEDs indicate detected status with is blinking green/red depending on the RFM variant.

BTS SW file transfer requires about 10 minutes. After this FSMF unit remains in reset state for another 5 minutes. The BTS manager connection will resume automatically at the end. In total approximately 15 minutes is required. Additional SW update may be required on site due to incompatible RFM SW versions. When FSMF is prepared prior to system module replacement, RFM detection can be confirmed from BTS Site manager Hardware view display with compatible WCDMA BTS Site manager.




Step 5 5.1

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF – start compatible BTS Site manager

- Start BTS Site manager in ‘Create File’ mode.

‘Create commissioning file’ view is displayed in BTS Site manager view.

BTS Site manager in ‘Create File’ is referred as ‘offline conversion’.

The conversion of FSME/D commissioning data for FSMF use can be also done when connected to FSMF. Both BTS and TRS parts are converted during commissioning steps. Therefore, the SCF preparation prior to site visit is optional. - Optionally, convert FSME/D commissioning data when connected to FSMF (step 9.1). Prepare SCF (BTS part) for FSMF - In ‘Introduction’ page,

5.2

- Select ‘BTS’ option as ‘Target’, select ‘Create file from existing commissioning file’ and locate previously stored backup commissioning file of BTS Site equipped with FSME/D (Backup file consists BTS part).

FSME/D BTS commissioning file is converted to FSMF commissioning file. FSMF TRS commissioning parameters to be manually added.

With RU30 Backup commissioning file Example: Backup SCF from WN7.0 2.0.

- Select ‘Convert’ to continue BTS commissioning file conversion to FSMF use.

The offline conversion of FSME/D TRS commissioning file to FSMF TRS commissioning file is not supported by WCDMA BTS Site manager. TRS parameters shall be manually added while navigating through commissioning wizard. Therefore only BTS part of the SCF can be converted for FSMF use with ‘Create file’ mode. Alternatively, the conversion of FSME/D TRS commissioning data for FSMF use can be done when connected to FSMF. Both BTS and TRS parts are converted during commissioning steps. Therefore, the SCF preparation prior to site visit is optional.

With RU40 Backup commissioning file Example: Backup SCF from WN8.0 1.0.

- Select ‘Next to continue BTS commissioning file conversion to FSMF use.

Table 4: Activities prior to site visit (continued) TS-3GBTS-SW-188 - Page 13/52 Version 7.0 Confidential


Step 5 5.3

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF - In ‘HW selection’ page,

- Replace System module ‘FSME/D’ with ‘FSMF’

FSME/D is removed and FSMF (and optional FTIF and FBBA) are added to BTS configuration. By adding optional FBBA submodules, the increased Flexi BTS baseband capacity can be used for R99/ HSDPA/ HSUPA traffic processing or additional CCCH and interference cancellation processing. HW configuration of BTS commissioning file is completed.

If optional FBBA is not used: - Radio module positions from existing configuration are automatically displayed. If optional FBBA is used: - add FBBA with ‘Add BB extension’ and select ‘FBBA (472182A)’ module(s).

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02 Document Change Delivery 3 Flexi Multiradio 10 BTS Quick Guide, Installing modules When FBBA is not in use, optical ports available for RFM use: FSMF RF/EXT1 Radio Module 1.1.1 FSMF RF/EXT2 Radio Module 1.2.1 FSMF RF/EXT3 Radio Module 1.3.1

When FBBA(s) is in use, optical ports available for RFM use: FSMF RF/EXT1 Radio Module 1.1.1 FSMF RF/EXT2 Radio Module 1.2.1 FSMF RF/EXT3 Radio Module 1.3.1 FBBA 2 RF/EXT Radio Module 1.4.1 FBBA 3 RF/EXT Radio Module 1.5.1

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Dimensioning WCDMA RAN: Flexi BTS Baseband - If additional RFM’s are added during FSMF swap, add ‘Radio module’ to available index on available optical port positions. RF SHARING (WCDMA BTS) EIF2/RF6 port is used to provide RP3-01 synchronisation for the slave BTS.




Step 5 5.4

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF - In ‘BTS Settings’ page,

When external GPS synchronization is received from another BTS,

Synchronization source/sharing is set.

In synchronization source BTS ’ commissioning, - select ‘Forward synchronization in co-siting’ and ‘GPS in use’.

In synchronization source BTS, time synchronization can be done based on GPS control data. In chained BTS, GPS control data cannot be used for time synchronization due to one way control data from synchronization source BTS. Hence, NTP is required for time synchronization. In BTS SCF, commissioning parameter ‘gpsCtrlBlockForCoLocatedBts’ is set as ‘True’ to close G PS communication port on BTS so that it does not confuse time synchronization with NTP. See 7.5.2 FSMF synchronization cables, 7.5.3 FSMF GPS feeding cables

In chained BTS s ynchronization commissioning, - select ‘GPS in use’ and ‘GPS control interface blocked for co-located BTS ’.




Step 5 5.5

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF - In ‘Automatic License Distribution Settings ’ page, R99 Channel Elements (CE)

- Set a value for R99 traffic. CCCH Processing set

When additional CCCH processing sets are added by BTS commissioning, no BTS reset is required.

FSMF contains resources for Common Control Channels processing for basic configurations. One CCCH pool is included in FSMF capacity which does not require any license. In case when more cells or higher cell radius is needed additional baseband resources (CCCH pools) and CCCH Processing Set licenses need to be allocated for CCCH processing. - Provision license key in use in NetAct License manager or alternatively in BTS Site manager - License Management. RU30 / WN7.0 3.0

- In RU30, there is no requirement to commission the number of licenses for CCCH Processing sets. You do still need to include the number of CCCH processing sets as part of the ba seband dimensioning exercise. CCCH Processing Set license keys are still required and BTS will automatically request the appropriate number from NetAct. RU40 / WN8.0 2.0 onwards

- In RU40, enter a value ‘CCCH processing set’ according cell configuration.

In case of FSMF, the Rel99 CE license defines the maximum capacity for pure Rel99 traffic. HSDPA/HSUPA schedulers are not consuming Rel99 CE licenses. One FSMF subunit provides capacity of 96 Rel99 CE’s. Number of subunits available: FSMF: 5.5 FSMF + 1 x FBBA: 11.5 FSMF + 2 x FBBA: 17.5 WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, CCCH requirements for Multiradio 10 BTS system modules Note: In RU30 to RU40 SW upgrade, with configurations that require additional CCCH Processing Sets, e.g. 2+2+2/20km, additional CCCH processing set(s) need to be manually defined in RU40 by recommissioning BTS.

Since no value can be set i n RU30 for CCCH Processing Set, BTS Site Configuration File (SCF) does not have a parameter set. During RU30 to RU40 SW upgrade, SCF conversion does not cover parameter for CCCH Processing Set, therefore it needs to be added by re-commissioning BTS.

Example: 3+3+3, 2xLCG, 9 cells 20Km.




Step 5 5.6

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF - In ‘WCDMA Carrier Candidates and Local Cell Group Settings ’ page,

In case of BASEBAND CAPACITY CHANGE from 2 x FSME to 1 x FSMF and more than 6 cells with HSPA are present ,

Local cells are distributed to required Local cell groups.

- select ‘Local cell groups in use ’ and ‘Frequency based grouping ’ or ‘Sector based grouping ’ based on your reference.

If ‘Local cell groups in use’ is not selected, and max. 6 cells are present, all local cells are added to Local cell group 1.

In ‘Carrier Candidate and local cell groups’,

- set ‘Local cell group’. When ‘Local cell groups in use’ is selected, at least 2 groups must be defined. Example: 3+3+3, 2xLCG, 9 cells 20Km.

... Example: MultiBand 3+3+3/1+1+1, 3xLCG, 12 cells 20 Km and 3 +3+3+3, 3xLCG 12 cells 20Km.

Local Cell Grouping allows splitting available baseband capacity into baseband pools responsible for processing traffic from dedicated group of cells.

Local Cell Grouping may be needed in case of BTSs with many cells, and can be used in Multi Operator RAN (MORAN). It is possible to use MORAN without Local Cell Grouping and dedicated baseband allocation. Frequency layer based commissioning - All cells from frequency layer(s) must be dedicated to the same Local Cell Group. Sector based commissioning - Dedication of cells from the same frequency layer(s) to different LCGs is allowed. - Dedication of cells from the same frequency layer(s) to the same LCG. In this case sector based commissioning might give the same results, as frequency layer based commissioning.

WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler When more than 6 cells with HSPA are present,

...

With 2 x FSME, one local cell group is defined. - 1 x LCG and 9 cells 20Km. With 1 x FSMF, at least 2 LCG’s must be defined - 2 x LCG and 9 cells 20Km, - 3 x LCG and 12 cells 20Km.




Step 5 5.6

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF (continued) - In ‘WCDMA Carrier Candidates and Local C ell Group Settings’ page, In ‘Baseband (BB) and HSPA license allocations’,

- set BB and HSPA license allocation values according Local Cell Group preference. Example: 3+3+3, 2xLCG, 9 cells 20Km.

Example: MultiBand 3+3+3/1+1+1, 3xLCG 12 cells 20 Km and 3+3 +3+3, 3xLCG, 12 cells 20Km.

In ‘Mapping HSPA local cells to baseband HW and Parallel Interference Cancellation (PIC),

- set ‘PIC pools’ starting from lowest number available and select ‘Next’ to continue. Example: 3+3+3, 2xLCG, 9 cells 20Km.

Example: MultiBand 3+3+3/1+1+1 3xLCG, 12 cells 20Km and 3+3+3+3, 3xLCG, 12 cells 20Km.

BB/HSPA license allocation and optional PIC pools are set. If ‘Local cell groups in use’ is not selected, BB and HSPA license allocation and PIC pool setting is not available.

WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler When more than 6 cells with HSPA are present, for example 3+3+3 and Multi Band 3+3+3/1+1+1 configuration With 2 x FSME, one local cell group is defined. - 1 x LCG and 9 cells 20Km. With 1 x FSMF, at least 2 LCG’s must be defined - 2 x LCG and 9 cells 20Km, - 3 x LCG and 12 cells 20Km. The maximum available baseband capacity of FSMF for pure traffic depends on - Local Cell Group (LCG) - configuration type - Additional CCCH processing resources (if needed) - Number of activated Interference Cancellation units (PIC pools) - HSUPA static resources (optional static reservation for HSUPA data/voice users) and - HS_Cell_FA CH_UL static resources (optional static reservation for HS-FA CH UL users). RAN1308 HSUPA Interference Cancellation Receiver

If PIC Pool is not in use, on RNC side edit the ‘AdminPicState’ in to ‘Disabled’ under Admission Control tab.




Step 5 5.7

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF - In ‘HSDPA Settings’ page,

Include adequate amount of ‘HSDPA capacity sets’ in order to get throughput allocated as per BTS Site preference. - set ‘BTS processing set 1/2/3‘ according BTS Site preferences. HSDPA BTS processing set capacities: HSDPA BTS processing set 1 32 users and 7.2Mbps HSDPA BTS processing set 2 72 users and 21Mbps HSDPA BTS processing set 3 72 users and 84Mbps.

HSDPA processing set(s) are commissioned.

The HSDPA BTS processing set describes the maximum HSDPA capability that allows reaching a certain number of HSDPA users and DL throughput WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler Formula for scheduler licensed throughput:

If there are only HSDPA Processing Set 2 and three l icenses are present in BTS, the division of licensed throughput will be done for each scheduler according to the formula below: Example: 3+3+3, 2xLCG, 9 cells 20Km, In total, 1 x 21 + 2 x 84 Mbps = 189Mbps of licensed capacity available for all schedulers. Scheduler licensed throughputs are calculated as per given formula (scheduler throughput steps from step 5.8) Scheduler 1 - LCG 1 = Round down {(1 + 4*2) * (12 /(12+6+6+3)) } * 21 Mbps = 84 Mbps Scheduler 2 - LCG 1 = Round down {(1 + 4*2) * (6 /(12+6+6+3)) } * 21 Mbps = 42 Mbps Scheduler 1 - LCG 2 = Round down {(1 + 4*2) * (6 /(12+6+6+3)) } * 21 Mbps = 42 Mbps Scheduler 2 - LCG 2 = Round down {(1 + 4*2) * (3 /(12+6+6+3)) } * 21 Mbps = 21 Mbps

Scheduler_licensed_throughput = Round_down { (Number_of_HSDPA_Processing_Sets_2 + 4* Number_of_HSDPA_Processing_Sets_3) * (Scheduler_HSDPA_throughput_step / Total_number_of_HSDPA_throughput_step_p er_BTS) } * 21 Mbps

If after calculations presented above throughput for all schedulers is lower than total licensed throughput in the BTS, the remaining throughput is distributed between activated schedulers. Schedulers are prioritized in the following order: a) Scheduler with lowest value of licensed throughput divided by commissioned throughput; b) Schedulers belonging to LCG with the lowest ID (in case of Normal HSPA configuration where 2 HSDPA schedulers activated, scheduler#1 is prioritized over scheduler#2).




Step 5 5.8

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF - In ‘HSDPA Throughput Settings’ page, In ‘HSPA setting’,

- select HSPA configuration (HSPA setting) option according LCG throughput requirements.

Optional HSPA setting is selected and HSDPA throughput steps are selected.

In ‘HSDPA throughput’,

- select a value according Local Cell Group requirements. This setting is optional. If ‘Max throughput’ is left as ‘System default’, then 84Mbps is allocated to every 1-6 non-MIMO cells.

In case BASEBAND CAPACITY CHANGE from 2 x FSME to1 x FSMF and more than 6 cells with HSPA are present , - select ‘HSDPA throughput’ according Local Cell Group preference. Each HSDPA throughput step corresponds to 7.2Mbps.

There are three LCG configuration types available for FSMF which describes HSPA capability (number of HSPA supported cells and number of HSDPA/HSUPA schedulers). Rel.99 only configuration Max number of supported cells = 12 Max number of HSPA cells = 6 Number of HSDPA schedulers = 0 Small HSPA configuration Max number of supported cells = 6 Max number of HSPA cells = 6 Number of HSDPA schedulers = 1 Normal HSPA configuration Max number of supported cells = 12 Max number of HSPA cells = 12 Number of HSDPA schedulers = 2

The LCG configuration type is set during B TS commissioning for each LCG separately using HSPA setting parameter. If not commissioned then ‘Normal HSPA’ configuration is assumed by default. WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler

Example: 3+3+3, 2xLCG, 9 cells 20Km. The scheduler provides HSDPA throughput, which depends on activated features, number and type of BTS processing sets, and HSDPA throughput commissioning by the operator. The HSDPA throughput step has No impact on HSDPA baseband capacity allocation but it is used for HSDPA licensed throughput distribution among available schedulers. In addition it can be used to limit HSDPA scheduler throughput.




Step 5 5.9

Description

Expected result

Further details

Prepare SCF (BTS part) for FSMF - In ‘Summary’ page,

- Navigate through commissioning steps to ‘Summary’ view and save BTS commissioning file. After saving BTS commissioning file, the following popup is shown.

BTS commissioning file is ready. TRS commissioning file to be prepared next.

- Select ‘Define new configuration ’ to create TRS commissioning file next. TRS commissioning file can a lso be created by starting the BTS Site manager again in Create File – mode (see 5.1).




Step 6 6.1

Description

Expected result

Further details

Prepare SCF (TRS part) for FSMF - In ‘Introduction’ page,

- Select ‘TRS’ option as ‘Target’, continue with ‘Next’.

- Optionally, convert the FSME/D commissioning data when connected to FSMF (step 9.1).

Existing FSME/D TRS commissioning file cannot be used in offline conversion (with ‘Create File’ –mode). FSMF TRS commissioning file parameters need to be manually added. Therefore, open previously stored snapshot with offline BTS Site manager to view TRS parameters. And copy them accordingly to FSMF TRS commissioning. The conversion of FSME/D TRS commissioning data for FSMF use can be done when connected to FSMF. Both BTS and TRS parts are converted during commissioning steps. Therefore, the SCF preparation prior to site visit is optional.

Prepare SCF (TRS part) for FSMF - In ‘HW selection’ page,

6.2

Optional FTIF is not used: - Select ‘Add TRS’ and choose ‘FSMx rel3’. Optional FTIF is used: - Select ‘Add TRS’ and choose ‘FTIF’.

Snapshot can be viewed with offline BTS Site manager while setting TRS parameters for FSMF commissioning. TRS commissioning files can be viewed with compatible BTS Site manager in ‘Create file’ mode.




Step 6 6.3

Description

Expected result

Further details

Prepare SCF (TRS part) for FSMF - In ‘Site Properties’ page,

Site specific IP configuration is different between FSME/D and FSMF. With FSMF, ‘BTS IP address is not displayed and therefore it is not needed.

- Set ‘TRS’, ’RNC’ and ‘NTP’ IP addresses.

Furthermore, BTS commissioning file does not have ‘btsIpAddr’ name element instance. - Continue to navigate through commissioning steps and copy parameters accordingly from previously saved TRS commissioning file or snapshot.




Step 6 6.4

Description

Expected result

Further details

Prepare SCF (TRS part) for FSMF – In ‘Physical Layer Configuration ’ page

Define Ethernet interface which will be used for Iub connectivity. Optional FTIF module not used: - Select transport interface EIF port: EIF1 – FSM 1 or EIF2 – FSM 2.

Optional FTIF module used:

Port ‘OPT-EXT1’ (Radio Module 1.4.1) of FSME/D is used for slave BTS synchronisation in RF sharing. With FSMF slave BTS synchronisation is routed through EIF2/RF6 port.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02, Documentation Change Delivery 3 RU40 Feature Descriptions and Instructions 4.2 RAN2296: FTIF Eth+E1/T1/JT1 for Flexi Multiradio System Module

- Select transport interface EIF port: EIF 3 - FTIF 3 or EIF 4 - FTIF 4.

RF SHARING (WCDMA BTS)

- Select ‘Enable FSM EIF2 as RP3-01 interface’ for slave BTS synchronisation use.




Step 6 6.5

Description

Expected result

Further details

Prepare SCF (TRS part) for FSMF - In ‘Summary’ page,

- Continue to navigate through commissioning steps to ‘Summary’ page and save TRS commissioning file.

TRS commissioning file is ready. BTS and TRS commissioning files are both ready.


7.4 Steps during to site visit Step 7 7.1

Description

Expected result

Further details

Save existing BTS data

- Establish remote BTS Site manager connection to the existing WCDMA BTS equipped with FSME/D module.

Backup SCF and snapshot is stored to local directory.

- Store 3 files: 1) Backup commissioning file, select ‘BTS’ as Target, ‘File -> Backup Commissioning Files…’ and save it to local directory. 2) Save Snapshot (select ‘Current data in BTS Site Manager ’ option to save time) and save it local directory.

3) From ‘License Management’ NetAct tool, export the existing NB pool license. When BTS license is exported from NetAct license pool, it’s possible to regenerate it and import it to NetAct license pool again as BTS license.

Table 17: Activities during site visit



Step 7 7.2

Description

Expected result

Further details

cabling & SFP modules from system module and remove it from rack.

FSME/D System module(s) is removed BTS Site.

Note: FSME/D as an Extension System module cannot be used with FSMF until further notice.

FSMF with optional submodule(s) is replaced to BTS Site.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Flexi Multiradio 10 BTS Quick Guide, Installing optional sub-modules

HW replacement

- Power down FSME/D, disconnect all

- Equip FSMF with optional sub-modules according to the target BTS site requirements. Do not mix FPFD and FTIF interconnection plug-in cards. FTIF interconnection plug-in card is labeled with ‘FSM’ and ‘TRS’. FPFD plug-in card is labeled with ‘Power unit FPFD’.

- Install FSMF core loosely inside the casing. Cabling is only possible when FSMF is loosely fitted to casing.

Table 18: Activities during site visit (continued)



Step 7 7.3

Description

Expected result

Further details

FSMF power cabling completed.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Flexi Multiradio 10 BTS Quick Guide, Cabling, Connecting external power feed

RFM power cabling completed.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Flexi Multiradio 10 BTS Quick Guide, Cabling, Connecting external power feed

FSMF power feeding

If optional FPFD is not used: - Connect external power source for FSMF directly to DC in connector. If optional FPFD is used: - Connect power source to FPFD power distribution unit installed together with FSMF. Use correct interconnection plug-in card provided with FPFD unit. - Strip DC input cables exactly to 16mm before fitting them. Ensure that cables are securely fitted to FPFD main terminal. RFM power feeding from FSMF

7.4

- Remove rubber boot and connector from the existing RFM power cable. - Strip exactly to 10mm. - Connect RFM cables to FPFD DC output terminals in the following recommended order: FPFD RF1 FPFD RF2 FPFD RF3 FPFD EXT FSMF DC out

Radio Module 1.1.1 Radio Module 1.2.1 Radio Module 1.3.1 Radio Module 1.x.x FBBA 2 (and FBBA 3)

Maximum power consumption of DC outputs: FPFD RF1 FPFD RF2 FPFD RF3 FPFD EXT FSMF DC out

1100W 1100W 1100W 1100W 600W

Instead of the existing power cables, consider using the following cable options: FPCB 472817A is a 2 m (6.6 ft) single DC power cable with connectors and IP seals on both ends. If it is used with FSMF, the connector and rubber boot needs to be removed from one end. FPCC 472823A is a 2 m (6.6 ft) single DC power cable with a connector on one end and open on the other end.

Over current protection of DC outputs: FPFD RF1 FPFD RF2 FPFD RF3 FPFD EXT FSMF DC out

31.0A ± 5% 31.0A ± 5% 31.0A ± 5% 31.0A ± 5% 18.0A ± 5%




Step

Description

Expected result

7

Installing optional Flexi Power module/battery backup

7.5

FSMF Site support interface is LMP connector. The same connector is used for local BTS Site manager connection. FSME/D has separate connector for site support interface port. If LMP port is required for Site support interface and intelligent shutdown is used, - Connect RJ45 alarm cable from FPMA Flexi power module (FPAA/FPBA/FPBB) to FSMF LMP connector. - In commissioning, select ‘Flexi Power Module’. 2 EAC lines are reserved for FPMA use. One line for FPAA/FPBA/FPBB alarm and second line for ‘Mains breakdown’ alarm that is controlling intelligent shutdown feature.

Battery backup cabling completed. FPMA/NSN BBU/Other BBU is connected to BTS with appropriate FSMF EAC cable and FSEA/ FSEB/Other EAC box.

Further details

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items, Installing Flexi Power Module (FPMA) WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items, Installing Flexi System External Alarm (FSEB) 7.5.4 FSMF EAC cables 7.5.10 FSMF LMP connector pin map

If LMP port is required for local BTS management use and intelligent shutdown feature is used, - In commissioning, select ‘Other BBU’ and define ‘External Fault Line ID’. Mains breakdown alarm line is connected to this External Fault Line. - Modify battery backup alarm cable and connect it to EAC box screw terminal accordingly.




Step 7 7.6

Description

Expected result

Further details

All SFP modules installed in FSMF.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02 Document Change Delivery 3 Flexi Multiradio 10 BTS Quick Guide, Cabling, Optical cabling

Installing SFP modules in FSMF

- Pull out the existing SFP modules from FSME/D. - Install SFP modules in FSMF to following optical ports FSMF RF/EXT1 Radio Module 1.1.1 FSMF RF/EXT2 Radio Module 1.2.1 FSMF RF/EXT3 Radio Module 1.3.1

7.5.6

FBBA 2 RF/EXT Radio Module 1.4.1 FBBA 3 RF/EXT Radio Module 1.5.1

7.5.7 7.5.8

RF SHARING (WCDMA BTS)

Radio modules with 6 GB RP3-01 link speed support SFP modules for 6 GB RP3-01 link speed SFP modules for 3 GB RP3-01 link speed

FSMF EIF2/RF6 RP3-01 Synchronization to slave BTS.

7 7.7

Installing optical cables in FSMF Note: Clean the optical fiber connectors before installation.

- Connect RFM optical cables to FSMF optical ports in the following recommended order:

All optical cables connected in FSMF.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02 Document Change Delivery 3 Flexi Multiradio 10 BTS Quick Guide, Installing modules

FSMF RF/EXT1 Radio Module 1.1.1 FSMF RF/EXT2 Radio Module 1.2.1 FSMF RF/EXT3 Radio Module 1.3.1 FBBA 2 RF/EXT Radio Module 1.4.1 FBBA 3 RF/EXT Radio Module 1.5.1 RF SHARING (WCDMA BTS) EIF2/RF6 – PR3-01 Synchronization to slave BTS

- Connect optical cables in RFM end exactly in the same order as with FSME/D.




Step 7 7.8

Description

Expected result

Further details

Transmission cabling completed.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02 Cabling Flexi Multiradio 10 Base Station - Connecting transmission cables

Installing transmission cabling

Optional FTIF module not used: - Connect transport cabling to selected EIF port (EIF1 or EIF2/RF6). Optional FTIF module used: - See further details.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02, Documentation Change Delivery 3 RU40 Feature Descriptions and Instructions 4.2 RAN2296: FTIF Eth+E1/T1/JT1 for Flexi Multiradio System Module Installing support for external IP devices

7.9

LMP port is to provide IP connectivity for external devices.

All external devices requiring IP connectivity shall be connected to a external 10/100Mbit switch that is connected to LMP port.

When RCUA is used with FSMF, - connect the device via external 10/100 Mbit switch. RCUA works with 10 Mbit/s speed with no auto negotiation support.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 04 Documentation Change Delivery 1 Cabling Flexi Multiradio 10 Base Station - Connecting external IP devices

Grounding

7.10

- See further details.

Grounding completed.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 02 Document Change Delivery 3 Flexi Multiradio 10 BTS Quick Guide, Grounding the BTS




Step 7 7.11

Description

Expected result

Further details

If GPS receiver is used for synchronization:

All cabling completed.

- Connect GPS cable to Sync in port.

BTS hardware configuration ready for SW update.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Cabling Flexi Multiradio 10 Base Station - Connecting Sync Out cable & Connecting Sync In cable

Other cabling

If Sync In/Out ports are used: - Connect FSMF specific sync cable(s) to Sync In and/or Sync Out ports. If EAC fault lines are used: - Connect FSMF specific EAC cable to EAC port. Note: FSMF supports only 12 EAC lines. If External Control lines 1….6 are used then External fault lines 7…12 cannot be configured in use.

If EAC control lines are used:

- Existing EAC commissioning and actual cabling configuration may need to be reconfigured.

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Installing GPS Antenna Kit (FYGA) or GPS GLONASS Receiver Antenna (FYGB) WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Cabling Flexi Multiradio 10 Base Station - Connecting External Alarms and Controls (EAC) cable 7.5.2 7.5.3 7.5.3 7.5.4

FSMF synchronization cables FSMF GPS feeding cables FSMF EAC cables FSMF EAC signal and pin assignment




Step 8 8.1

Description

Expected result

Further details

Power up FSMF and check running SW versions

- Power up FSMF.

BTS Site Manager connection is successful.

- Start BTS Site manager to establish connection with FSMF. - Check that RF modules are detected/displayed on BTS Site manager Hardware view. 0023 Incompatible SW version detected – alarm may be displayed for RF module(s), as FSMF and RFM SW may not be yet compatible.

All RF module(s) are detected and displayed in BTS Site manager.

Note: FSMF with factory load requires compatible LTE BTS Site manager in o rder to have detected HW modules displayed.

If FSMF is not updated to desired WCDMA BTS SW, and LTE BTS Site manager is not available, no HW modules are displayed in BTS Site manager. Before starting the SW upgrade, check the RFM LED status to confirm unit has been detected by FSMF. Detected RFM LED status is blinking green/ blinking red depending on the RFM variant. SW update of existing RFMs

8.2

FSMF updated prior to site installation: - Download and activate the desired BTS SW again to initiate RFM SW upgrade.

Time required is approximately 10 min.

If a firewall is installed on the PC, you may need to configure it to allow ports 13062 – 13092 to accept incoming connections from the Flexi Multiradio BTS.

Time required is approximately 18 - 20 min.

This TCP port must be ‘open’ to enable Flexi BTS Site Manager software downloading. For further information about the specific firewall installed on your PC, contact your System Administrator or IT Helpdesk.

Only RFM(s) are reset to activate new SW. FSMF updated during site installation: - Download and activate the desired BTS SW (FSMF and RFM’s) .




Step 9 9.1

Description

Expected result

Further details

Template commissioning - In ‘Introduction’ page

TEMPLATE COMMISSIONING Choose this option to convert BTS and TRS commissioning parameters when connected to FSMF BTS Site.

TRS parameter conversion is supported for Transport units equipped with both PDH & Ethernet interfaces (FTIA, FTJA, FTIA, FTIB, FTLB and FTFA, FTFB).

- Select FSME/D backup commissioning file and proceed with ‘Next’. With RU30 Backup commissioning file Example: Backup SCF from WN7.0 2.0.

- Select ‘Convert’ to continue BTS commissioning file conversion to FSMF use.

- Select ‘Convert’ to continue TRS commissioning file conversion to FSMF use.

- Continue to navigate through commissioning steps.




Step 9 9.1

Description

Expected result

Further details

Template commissioning - In ‘Introduction’ page (continued) With RU40 Backup commissioning file Example: Backup SCF from WN8.0 1.0.

Some of the parameters from the BTS equipped with FSME/D cannot be used with FSMF. Therefore, an indication of invalid parameters is displayed. Indication does not require any action.

TRS parameter conversion is supported for Transport units equipped with both PDH & Ethernet interfaces (FTIA, FTJA, FTIA, FTIB, FTLB and FTFA, FTFB).

- Select ‘Continue’ to navigate through commissioning steps.

- Continue to navigate through commissioning steps.




Step 9 9.2

Description

Expected result

Further details

Template commissioning - In ‘Site Properties’ page

Site specific IP configuration is different between FSME/D and FSMF. With FSMF, ‘BTS IP address is not displayed and therefore it is not needed.

- Set ‘TRS’, ’RNC’ and ‘NTP’ IP addresses.

Furthermore, BTS commissioning file does not have ‘btsIpAddr’ name element instance. - Continue to navigate through commissioning steps and copy parameters accordingly from previously saved TRS commissioning file or snapshot.




Step 9 9.3

Description

Expected result

Further details

Template commissioning - In ‘Physical Layer Configuration ’ page Optional FTIF module not used :

SCF conversion does not automatically select any Ethernet port in use, therefore - Select Ethernet port which will be used for Iub connectivity, EIF1 – FSM 1 or EIF2/RF6 – FSM 2).

RF SHARING (WCDMA BTS) Port ‘OPT-EXT1’ (Radio Module 1.4.1) of FSME/D is used for slave BTS synchronisation in RF sharing. With FSMF slave BTS synchronisation is routed through EIF2/RF6 port.

- Select ‘Enable FSM EIF2 as RP3-01 interface’ for slave BTS synchronisation use.

- Navigate through commissioning steps and make necessary changes if required (all values are as expected as a default). - Save commissioning file and ‘ Send parameters’ to activate new commissioning




Step 9 9.3

Description

Expected result

Further details

Template commissioning - In ‘Physical Layer Configuration ’ page (continued) Optional FTIF module used:

FSME/D transmission interface Ethernet port is automatically converted to FTIF 2. It cannot be used with FTIF. With RU30 Backup commissioning file Example: Backup SCF of WN7.0 2.0.

The conversion of TRS commissioning data is does not take in account different TRS submodule variants. Therefore, some FTIF parameters need to be modified after the parameter conversion has mapped used FSME/D EIF port values directly for FSMF use.

With RU40 Backup commissioning file Example: Backup SCF of WN8.0 1.0.




Step 9 9.4

Description

Expected result

Further details

Template commissioning - In ‘Synchronization’ page Optional FTIF module used (continued):

- Alternatively, unselect Ethernet Interface EIF ‘FTIF 2’ and select EIF ‘ FTIF 3.’

If the use of feature RAN2071 was enabled for FSME/D, the conversion does not automatically enable the feature is use.

Optional RAN2071 Synchronous Ethernet regenerator – feature is in use.

- Select ‘In use’ for Synchronous Ethernet regenerator .




Step 9 9.5

Description

Expected result

Further details

Template commissioning - In ‘Automatic Licence Distribution Settings ’ R99 Channel Elements (CE)

CCCH Processing set

When additional CCCH processing sets are added by BTS commissioning, no BTS reset is required.

In case of FSMF, the Rel99 CE license defines the maximum capacity for pure Rel99 traffic. HSDPA/HSUPA schedulers are not consuming Rel99 CE licenses.

FSMF contains resources for Common Control Channels processing for basic configurations.

R99 CE’s and CCCH processing set(s) are defined.

One FSMF subunit provides capacity of 96 Rel99 CE’s.

- Set a value for R99 traffic.

One CCCH pool is included in FSMF capacity which does not require any license. In case when more cells or higher cell radius is needed additional baseband resources (CCCH pools) and CCCH Processing Set licenses need to be allocated for CCCH processing. - Provision license key in use in NetAct License manager or alternatively in BTS Site manager - License Management. RU30 / WN7.0 3.0

- In RU30, there is no requirement to commission the number of licenses for CCCH Processing sets. You do still need to include the number of CCCH processing sets as part of the b aseband dimensioning exercise. CCCH Processing Set license keys are still required and BTS will automatically request the appropriate number from NetAct. RU40 / WN8.0 2.0 onwards

- In RU40, enter a value ‘CCCH processing set’ according cell configuration.

Number of subunits available: FSMF: 5.5 FSMF + 1 x FBBA: 11.5 FSMF + 2 x FBBA: 17.5 WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, CCCH requirements for Multiradio 10 BTS system modules Note: In RU30 to RU40 SW upgrade, with configurations that require additional CCCH Processing Sets, e.g. 2+2+2/20km, additional CCCH processing set(s) need to be manually defined in RU40 by recommissioning BTS.

Since no value can be set in RU30 for CCCH Processing Set, BTS Site Configuration File (SCF) does not have a parameter set. During RU30 to RU40 SW upgrade, SCF conversion does not cover parameter for CCCH Processing Set, therefore it needs to be added by re-commissioning BTS.

Example: 3+3+3, 2xLCG, 9 cells 20Km. 2 CCCH processing sets required.




Step 9 9.6

Description

Expected result

Further details

Template commissioning - In ‘WCDMA Carrier Candidates and Local Cell Group Settings ’ page,

In case of BASEBAND CAPACITY CHANGE from 2 x FSME to 1 x FSMF and more than 6 cells with HSPA are present , - select ‘Local cell groups in use ’ and ‘Frequency based grouping ’ or ‘Sector based grouping ’ based on your reference.

Local cell(s) are assigned to Local cell group(s). If ‘Local cell groups in use’ is not selected, and max. 6 cells are present, all local cells are added to Local cell group 1.

In ‘Carrier Candidate and local cell groups’,

- set ‘Local cell group’. Note when ‘Local cell groups in use’ is selected, at least 2 groups must be defined. Example: 3+3+3, 2xLCG, 9 cells 20Km.

... Example: MultiBand 3+3+3/1+1+1, 3xLCG, 12 cells 20 Km.

Local Cell Grouping allows splitting available baseband capacity into baseband pools responsible for processing traffic from dedicated group of cells. Local Cell Grouping may be needed in case of BTSs with many cells, and can be used in Multi Operator RAN (MORAN). It is possible to use MORAN without Local Cell Grouping and dedicated baseband allocation. Frequency layer based commissioning All cells from frequency layer(s) must be dedicated to the same Local Cell Group. Sector based commissioning - Dedication of cells from the same frequency layer(s) to different LCGs is allowed. - Dedication of cells from the same frequency layer(s) to the same LCG. In this case sector based commissioning might give the same results, as frequency layer based commissioning. WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler When more than 6 cells with HSPA are present,

...

With 2 x FSME, one local cell group is defined. - 1 x LCG and 9 cells 20Km. With 1 x FSMF, at least 2 LCG’s must be defined - 2 x LCG and 9 cells 20Km, - 3 x LCG and 12 cells 20Km.




Step 9 9.6

Description

Expected result

Further details

Template commissioning - In ‘WCDMA Carrier Candidates and Local Cell Group Settings ’ page (continued), In ‘Baseband (BB) and HSPA license allocations’,

- set BB and HSPA license allocation values according Local Cell Group preference. Example: 3+3+3, 1xLCG, 9 cells 20Km.

BB/HSPA license allocation and optional PIC pools are set. If ‘Local cell groups in use’ is not selected, BB and HSPA license allocation and PIC pool setting is not available.

Example: MultiBand 3+3+3/1+1+1, 2xLCG, 12 cells 20 Km.

WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler When more than 6 cells with HSPA are present, for example 3+3+3 and Multi Band 3+3+3/1+1+1 configuration With 2 x FSME, one local cell group is defined. - 1 x LCG and 9 cells 20Km. With 1 x FSMF, at least 2 LCG’s must be defined - 2 x LCG and 9 cells 20Km, - 3 x LCG and 12 cells 20Km.

In ‘Mapping HSPA local cells to baseband HW and Parallel Interference Cancellation (PIC),

- set ‘PIC pools’ starting from lowest number available and select ‘Next’ to continue. Example: 3+3+3, 1xLCG, 9 cells 20Km.

The maximum available baseband capacity of FSMF for pure traffic depends on - Local Cell Group (LCG) - configuration type - Additional CCCH processing resources (if needed) - Number of activated Interference Cancellation units (PIC pools) - HSUPA static resources (optional static reservation for HSUPA data/voice users) - HS_Cell_FACH_UL static resources (optional static reservation for HS-FA CH UL users) RAN1308 HSUPA Interference Cancellation Receiver

Example: MultiBand 3+3+3/1+1+1 3xLCG, 12 cells 20Km or 3+3+3+3, 3xLCG, 12 cells 20Km.

If PIC Pool is not in use, on RNC side edit the ‘AdminPicState’ in to ‘Disabled’ under Admission Control tab.




Step 9 9.7

Description

Expected result

Further details

Template commissioning - In ‘HSDPA Settings’ page,

Include adequate amount of ‘HSDPA capacity sets’ in order to get throughput allocated as per BTS Site preference. - set ‘BTS processing set 1/2/3‘ according BTS Site preferences. HSDPA BTS processing set capacities: HSDPA BTS processing set 1 32 users and 7.2Mbps HSDPA BTS processing set 2 72 users and 21Mbps HSDPA BTS processing set 3 72 users and 84Mbps.

HSDPA processing set(s) are commissioned.

The HSDPA BTS processing set describes the maximum HSDPA capability that allows reaching a certain number of HSDPA users and DL throughput WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler Formula for scheduler licensed throughput:

If there are only HSDPA Processing Set 2 and three l icenses are present in BTS, the division of licensed throughput will be done for each scheduler according to the formula below: In total, 1 x 21 + 2 x 84 Mbps = 189Mbps of licensed capacity available for all schedulers. Scheduler licensed throughputs are calculated as per given formula (scheduler throughput steps from step 9.7) Scheduler 1 - LCG 1 = Round down {(1 + 4*2) * (12 /(12+6+6+3)) } * 21 Mbps = 84 Mbps Scheduler 2 - LCG 1 = Round down {(1 + 4*2) * (6 /(12+6+6+3)) } * 21 Mbps = 42 Mbps Scheduler 1 - LCG 2 = Round down {(1 + 4*2) * (6 /(12+6+6+3)) } * 21 Mbps = 42 Mbps Scheduler 2 - LCG 2 = Round down {(1 + 4*2) * (3 /(12+6+6+3)) } * 21 Mbps = 21 Mbps

Scheduler_licensed_throughput = Round_down { (Number_of_HSDPA_Processing_Sets_2 + 4* Number_of_HSDPA_Processing_Sets_3) * (Scheduler_HSDPA_throughput_step / Total_number_of_HSDPA_throughput_step_p er_BTS) } * 21 Mbps

If after calculations presented above throughput for all schedulers is lower than total licensed throughput in the BTS, the remaining throughput is distributed between activated schedulers. Schedulers are prioritized in the following order: a) Scheduler with lowest value of licensed throughput divided by commissioned throughput; b) Schedulers belonging to LCG with the lowest ID ( in case of Normal HSPA configuration (2 HSDPA schedulers activated) scheduler#1 is prioritized over scheduler#2).




Step 9 9.8

Description

Expected result

Further details

Template commissioning - In ‘HSDPA Throughput Settings’ page, In ‘HSPA setting’,

- select HSPA configuration (HSPA setting) option according LCG throughput requirements.

In ‘HSDPA throughput’,

- select a value according Local Cell Group requirements. This setting is optional. If ‘ Max throughput’ is left as ‘System default’, then 84Mbps is allocated to every 1-6 non-MIMO cells.

In case BASEBAND CAPACITY CHANGE from 2 x FSME to1 x FSMF and more than 6 cells with HSPA are present , - select ‘HSDPA throughput’ according Local Cell Group preference. Each HSDPA throughput step corresponds to 7.2Mbps.

Optional HSPA setting is selected and HSDPA throughput steps are selected.

There are three LCG configuration types available for FSMF which describes HSPA capability (number of HSPA supported cells and number of HSDPA/HSUPA schedulers). Rel.99 only configuration Max number of supported cells = 12 Max number of HSPA cells = 6 Number of HSDPA schedulers = 0 Small HSPA configuration Max number of supported cells = 6 Max number of HSPA cells = 6 Number of HSDPA schedulers = 1 Normal HSPA configuration Max number of supported cells = 12 Max number of HSPA cells = 12 Number of HSDPA schedulers = 2

The LCG configuration type is set during B TS commissioning for each LCG separately using HSPA setting parameter. If not commissioned then ‘Normal HSPA’ configur ation is assumed by default. WCDMA RAN and Flexi Direct BTS, Rel.RU40, Operating Documentation Dimensioning WCDMA RAN: Flexi BTS Baseband, Flexi System Module Rel.3 HSDPA scheduler

Example: 3+3+3, 2xLCG, 9 cells 20Km. The scheduler provides HSDPA throughput, which depends on activated features, number and type of BTS processing sets, and HSDPA throughput commissioning by the operator. The HSDPA throughput step has No impact on HSDPA baseband capacity allocation but it is used for HSDPA licensed throughput distribution among available schedulers. In addition it can be used to limit HSDPA scheduler throughput




Step 9 9.9

Description

Expected result

Template commissioning - In ‘Antenna Line Settings’ page,

When RCUA+WMHC is used with FSMF,

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 04 Documentation Change Delivery 1 Commissioning Flexi Multiradio BTS WCDMA, Performing RealTilt Commissioning

- allocate IP address for RCUA according to the principles described in the WCDMA RAN documentation. A public IP address/routing must be arranged also for the RealTilt Solution according to the same principles. - connect the device via external 10/100 Mbit switch/hub. RCUA works with 10 Mbit/s speed with no auto negotiation support.

If a firewall is installed on the PC, you may need to configure it to allow TCP ports 13062 – 13092 to accept incoming connections from the Flexi Multiradio BTS.

- see further details for performing RealTilt commissioning. Continue to navigate through the rest of the commissioning steps and before sending parameters, save commissioning file for reference / RF sharing to introduce WBTS commissioning to 2G BTS.

10 10.1

Further details

This TCP port must be ‘open’ to enable Flexi BTS Site Manager commissioning file transfer to BTS. For further information about the specific firewall installed on your PC, contact your System Administrator or IT Helpdesk.

Update 2G BTS commissioning (optional) RF SHARING (2G BTS)

- Establish 2G BTS Site manager connection, go into Commissioning Wizard and select ‘Change settings Manually’ option.

2G BTS Site manager connection can be established

- Navigate through commissioning steps until ‘HW Configuration’ page, select ‘Specify from File’ and pick previously saved WCDMA BTS commissioning file (step 9.2).

Prepared 3G SCF can be selected and commissioning process is started

- Select ‘Do no change settings’ option in Transmission Parameter view in o rder to speed up re-commissioning step. - Select ‘Send SCF’ to activate new commissioning file.

2G BTS will perform a restart to activate new commissioning file.




Step 11 11.1

Description

Expected result

Further details

Finish.

- Unlock WCEL's in RNC

WBTS On Air.

- Check alarms

No unexpected alarms.

Reported HSDPA throughput values (displayed in Site Information file) when Licensed HSDPA throughput is ideally set. Example: 3+3+3, 2 x LCG, 9 cells 20Km




7.5 Additional information 7.5.1 FSMF sub-modules Product Code 472301A

472182A

472311A

Name

Contents

FPFD

Power Distribution Sub –Module

FBBA

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Flexi Multiradio Base Station and Flexi M ultiradio 10 Base Station Optional Items Description, Flexi Power Distribution Sub-Module (FPFD) description Capacity Extension Sub –Module

FTIF

WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 Cabling Flexi Multiradio 10 Base S tation, Connecting Flexi Multiradio 10 BTS C apacity Extension Sub-Module (FBBA) cabling Transport Sub-module WCDMA RAN, Rel. RU40, Operating Documentation, Issue 03 RU40 Feature Descriptions and Instructions 4.2 RAN2296: FTIF Eth+E1/T1/JT1 for Flexi Multiradio System Module

Table 38: FSMF sub-modules

7.5.2 FSMF synchronization cables Product Code 472685A 472576A 472799A 472808A 472686A 472846A 472509A

Name ESFB FTSG FSCB FTSK ESUB FTSN FTSF

Length (m) 12 2 5 2 12 15 2

Used for

Note

ESMA/B/C -> FSMF FSME/D -> FSMF FSMF -> ESMA/B/C FSMF -> FSME/D FSMF -> Ultrasite EDGE FSMF -> FSMF FSMF -> FSMF

Sync Cable ESMA/B/C to FSMF Sync Cable G Sync Cable FSMF to ESMA/B/C Sync Cable FSMF to FSMD/E Sync Cable FSMF to D15 Ultra Sync Cable FSMF to FSMF Sync Cable F

(MDR14 -> HDMI) (MDR14 -> HDMI) (HDMI -> MDR26) (HDMI -> MDR26) (HDMI -> D15) (HDMI - HDMI) (HDMI - HDMI)

Table 39: FSMF synchronization cables

7.5.3 FSMF GPS feeding cables Product Code 472510A 472577A

Name FTSE FTSH

Length (m) 30 100

Used for

Note

FSMF – GPS FSMF – GPS

GPS cable assembly GPS cable assembly

Table 40: GPS feeding cables



7.5.4 FSMF EAC cables Product Code 472839A 472693A 472578A

Name FSAH FSAE FTSI

Length (m) 15 2 2,5

Used for

Note

FSMF – FSEB (471424A) FSMF – units with RJ45 FSMF – FSEB (471424A)

EAC cable EAC cable EAC cable

(HDMI-D37) (HDMI-RJ45) (HDMI-D37)

Table 41: FSMF EAC cables

7.5.5 FSMF EAC signal and pin assignment Pin

Signal

Function

1

EXT_AL0_H

External Alarm 0

2

EXT_AL1_H

External Alarm 1

3

EXT_AL2_H

External Alarm 2

4

EXT_AL3_H

External Alarm 3

5

EXT_AL4_H

External Alarm 4

6

EXT_AL5_H

External Alarm 5

7

EXT_CTRL0_EXT_AL6_H

Shared Control line 0 / Alarm 6

8

EXT_CTRL1_EXT_AL7_H


9

EXT_CTRL2_EXT_AL8_H


10

EXT_CTRL3_EXT_AL9_H


11

EXT_CTRL4_EXT_AL10_H


12

EXT_CTRL5_EXT_AL11_H


13

GND

Ground

14

GND

Ground

15

PROT_CAN_H_P5V_EAC

CAN serial line positive

16

GND

Ground

17

PROT_CAN_L_P5V_EAC

CAN serial line negative

18

P5V_EAC

CAN 5V Supply or Supply for Controls

19

GND

Ground

Table 42: FSMF EAC interface signals and pin assignment



7.5.6 Radio modules with 6 GB RP3-01 link speed support The following Flexi Multiradio BTS RFM release 3 HW modules support 6 GB RP3-01 link speeds. Product Code 472573A 472678A 472501A 472679A 472649A 472650A 472441A 472810A

Name

Note

FXDB FXCB FXEB FXFC FHDB FHEB FRGS FRGT

Flexi RF module 3-sector 900MHz 3x80W Flexi RF module 3-sector 850MHz 3x80W Flexi RF module 3-sector 1800MHz 3x80W Flexi RF module 3-sector 1900MHz 3x80W Flexi Remote Radio head 900MHz 2x60W Flexi Remote Radio head 1800MHz 2x60W Flexi RF module 3-sector 2100Mhz 3x80W Flexi RF module 3-sector 2100Mhz 3x80W

Table 43: RFM’s with 6 Gb RP3-01 link speed support All other delivered Legacy Radio Modules are supporting 3 Gb SFP ’s only.

7.5.7 SFP modules for 6 GB RP3-01 link speed 6 Gb SFP’s are for optical connection between FSMF and RFM release 3 HW. Product Code 472579A 472811A 472580A

Name FOSH FOSN FOSI

Max Cable Lenght (m) 200 2000 15000

Used for

Note

FSMF – RFM FSMF – RFM FSMF – RFM

6 Gb Multimode mode SFP 850 nm for OBSAI 6 Gb Single mode SFP 1310 nm for OBSAI 6 Gb Single mode SFP 1310 nm for OBSAI

Table 44: 6 GB SFP modules

7.5.8 SFP modules for 3 GB RP3-01 link speed 3 Gb SFP’s are for optical connection between FSMF and RFM and sharing synchronization between ESMA/B/C – FSMF and FSMC/D/E – FSMF. Product Code 472063A 472807A 471546A

Name FOSG FOSL FOSA

Max Cable Lenght (m) 200 2000 15000

Used for

Note

FSMF – RFM FSMF – RFM FSMF – RFM

3 Gb Multimode mode SFP 850 nm for OBSAI 3 Gb Single mode SFP 1310 nm for OBSAI 3 Gb Single mode SFP 1310 nm for OBSAI

Table 45: 3 GB SFP modules



7.5.9 FSMF interfaces FSMF System Module is equipped with the following interfaces: front panel connectors DC input connector (in the centre of the module) Flexi Multiradio System Module has 14 connectors on the module.  

Connector DC Out DC In

Type PwrProfile DC Terminal 2P

LMP Site Support Interface

RJ45

EIF2/RF/ EXT6

SFP

RF/EXT1 RF/EXT2 RF/EXT3

SFP SFP SFP

SRIO

SFP

BB EXT1

QSFP

BB EXT2

QSFP

EIF1

RJ45

EAC

HDMI

Sync In Sync Out

HDMI HDMI

Description Power output for power chaining to one optional baseband capacity extension sub-module. Power input connector for power distribution to the System Module. Ethernet interface for Element Manager or Site Support equipment (battery backup module, for example). All external devices requiring IP connectivity shall be connected to LMP using 10/100Mbit switch. An additional optical interface that provides RP3-01 (OBSAI) or CPRI interfacing to RF Module or RRH. Another option is interfacing to another System Module (RP3-01 only). Alternatively, it can be SW configured as a GbE interface for external transport. Note that this is the default configuration. Optical interfaces provide RP3-01 (OBSAI) or CPRI interfacing to RF Modules or RRHs. Another option is interfacing to other System Modules (RP3-01 only). Interface in the core module and one similar interface in each optional extension submodules support high-speed chaining up to nine System Modules per BTS. Interfaces for broadband interconnecting between the core module and the optional extension sub-modules. All necessary signals are carried over a single copper cable between the core module and the sub-module. 100/1000 Base-T Gigabit Ethernet interface for external transport, that is, interfacing towards the RAN, or directly towards the CN (LTE). External Alarms and Controls (EAC) interface provides six alarm signals and six SW controllable interfaces that can be assigned to support either control or alarm signals. HDMI-based input and output external synchronization interfaces enable, for example, interfacing to GPS equipment.

Table 46: FSMF connectors



Figure 4: FSMF System Module front panel



7.5.10 FSMF LMP connector pin map Pin

Function

1

Ethernet 100Mbit/s

2

Ethernet 100Mbit/s

3

Ethernet 100Mbit/s

4

signal (MIBBU alarm, from site support cabinet or power system)

5

signal (MIBBU alarm, from site support cabinet or power system)

6

Ethernet 100Mbit/s

7

GND

8

GND

Table 47: FSMF LMP connector pin map

Figure 5: FSMF LMP RJ45



298233143-FSME-D-to-FSMF-Replacement-Procedure-TS-SRAN-SW-188-I7.pdf

Recommend Documents