267663760-FPFC.pdf

LTE Radio Access, Rel. RL50, Operating Documentation, Issue 01

Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items DN09142359 Issue 01A Approval Date 2013-09-18 Confidential

Nokia Siemens Networks is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their components. If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia Siemens Networks for any additional information.

Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2013. All rights reserved

f

Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.

The same text in German:

f

Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen. Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen. Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes.

2

Id:0900d80580a24704 Confidential

DN09142359


Table of contents This document has 240 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1

Installing System Extension Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2

Installing Flexi Pole Installation Kit (FPIA) . . . . . . . . . . . . . . . . . . . . . . . 19

3

Installing Flexi Mounting Auxiliary Brackets (FMAA) . . . . . . . . . . . . . . . 22

4

Installing back covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5

Installing front covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6

Installing optional side cable tunnels . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

7 7.1 7.2

7.4

Installing Flexi Power Module (FPMA). . . . . . . . . . . . . . . . . . . . . . . . . . 31 Installing Flexi Power Module (FPMA). . . . . . . . . . . . . . . . . . . . . . . . . . 31 Powering an RF Module with a single FPMA equipped with one rectifier . 49 Powering an RF Module with a single FPMA equipped with 4 rectifiers/batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Powering two System Modules with a single FPMA . . . . . . . . . . . . . . . 58

8

Installing Flexi Power DC/DC Module 24V (FPDA) . . . . . . . . . . . . . . . . 61

9 9.1

Installing Flexi Power Rectifier (FPRx) . . . . . . . . . . . . . . . . . . . . . . . . . 70 Principles for installing Flexi Power Rectifier (FPRx) in Flexi Multiradio BTS configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

10 10.1 10.2

Installing Flexi Power AC/DC sub-module 230V (FPAC). . . . . . . . . . . . 72 Installing Flexi Power AC/DC sub-module (FPAC) on a wall. . . . . . . . . 72 Installing Flexi Power AC/DC sub-module (FPAC) to a pole-mounted RRH 78

11 11.1 11.2

Installing Flexi Power AC/DC sub-module (FPAD) . . . . . . . . . . . . . . . . 85 Installing Flexi Power AC/DC sub-module (FPAD) on a wall. . . . . . . . . 85 Installing Flexi Power AC/DC sub-module (FPAD) to a pole-mounted RRH 91

12 12.1 12.2

Installing Flexi Power Distribution and Fuses Outdoor (FPFC) . . . . . . . 99 Installing FPFC inside a casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Installing FPFC in a chained configuration . . . . . . . . . . . . . . . . . . . . . 114

13

Installing Flexi System External OVP (FSEC) . . . . . . . . . . . . . . . . . . . 116

14 14.1 14.2

Installing Flexi System External OVP (FSES) . . . . . . . . . . . . . . . . . . . 128 Installing Flexi System External OVP (FSES) onto a 3U casing . . . . . 128 Installing Flexi System External OVP (FSES) on a Flexi cabinet rooftop . 140 Installing Flexi System External OVP (FSES) onto Flexi Pole Installation Kit (FPIA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

7.3

14.3 15 15.1

DN09142359

Installing Flexi Fiber Optical Distribution unit (FODA) . . . . . . . . . . . . . 145 Installing Flexi Fiber Optical Distribution unit (FODA) in a stack . . . . . 145


3


15.2 15.3

Installing Flexi Fiber Optical Distribution unit (FODA) on a wall . . . . . . 153 Installing Flexi Fiber Optical Distribution unit (FODA) on a pole . . . . . . 158

16 16.1 16.2 16.3

Installing Flexi System External Alarm (FSEB). . . . . . . . . . . . . . . . . . . 164 Installing Flexi System External Alarm (FSEB). . . . . . . . . . . . . . . . . . . 164 FSEB interface signals and connector pin assignments. . . . . . . . . . . . 175 EAC cable (FTSI 472578A) wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

17

Installing GPS Antenna Kit (FYGA) or GPS GLONASS Receiver Antenna (FYGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

18

Installing Flexi GPS Surge Protection Kit (FYEA) . . . . . . . . . . . . . . . . . 185

19

Installing Flexi GPS Box (FYGD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

20

Installing UltraSite Outdoor Side Kit (OSKA) . . . . . . . . . . . . . . . . . . . . 197

21 21.1 21.2 21.3

Installing UltraSite IDC_ Roof Kit (IRSA) . . . . . . . . . . . . . . . . . . . . . . . 200 Installing UltraSite IDC_ Roof Kit (IRSA) . . . . . . . . . . . . . . . . . . . . . . . 200 Installing UltraSite IDC_ Roof Kit (IRSA) in normal position . . . . . . . . . 202 Installing UltraSite IDC_ Roof Kit (IRSA) in forward position . . . . . . . . 205

22 22.1 22.2 22.3 22.4 22.5 22.6 22.7 22.8 22.9 22.10 22.11 22.12 22.12.1 22.12.2 22.13 22.14 22.15 22.16

Appendix Contents of deliveries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 Contents of the System Extension Kit (FSKA) delivery . . . . . . . . . . . . 207 Contents of the System Extension Kit (FSKB) delivery . . . . . . . . . . . . 208 Contents of the Flexi Pole Installation Kit (FPIA) delivery. . . . . . . . . . . 209 Contents of the Flexi Mounting Auxiliary Bracket (FMAA) . . . . . . . . . . 210 Contents of the 3U mounting covers (FMCA) delivery . . . . . . . . . . . . . 211 Contents of the Flexi Mounting Covers Front and Back, 2U (FMCB) . . 212 Contents of the 3U Module Casings (EMHA) delivery . . . . . . . . . . . . . 213 Contents of the 2U Module Casings (EMTA) delivery . . . . . . . . . . . . . 215 Contents of the Flexi Side Covers (FMHA) delivery . . . . . . . . . . . . . . . 217 Contents of the Flexi Side Covers (FMTA) delivery . . . . . . . . . . . . . . . 218 Contents of the Flexi Mounting Shield 3U Casing (FMSC) delivery . . . 219 Contents of the Power Module (FPMA) delivery . . . . . . . . . . . . . . . . . . 220 Contents of the power AC/DC sub-module (FPAA) delivery. . . . . . . . . 221 Contents of the power battery sub-module (FPBA/B) delivery . . . . . . . 222 Contents of the 24V Power Module (FPDA) delivery . . . . . . . . . . . . . . 223 Contents of the Flexi Power AC/DC sub-module (FPAC) delivery . . . . 224 Contents of the Flexi Power AC/DC sub-module (FPAD) delivery . . . . 225 Contents of the Flexi Power Distribution and Fuses Outdoor (FPFC) delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 Contents of the Flexi System External OVP (FSEC) delivery . . . . . . . . 228 Contents of the Flexi System External OVP (FSES) delivery . . . . . . . . 229 Contents of the Flexi Fiber Optical Distribution unit (FODA) delivery . . 230 Contents of the Flexi System External Alarm Module (FSEB) . . . . . . . 231 Contents of the GPS hardware deliveries . . . . . . . . . . . . . . . . . . . . . . . 232 Contents of the Flexi GPS Surge Protection Kit (FYEA) delivery . . . . . 234 Contents of the Flexi System Alarm Cable (FSAA) delivery . . . . . . . . . 235 Contents of the GPS Box (FYGD) delivery . . . . . . . . . . . . . . . . . . . . . . 236 Contents of the Outdoor Side Kit (OSKA) delivery . . . . . . . . . . . . . . . . 237

22.17 22.18 22.19 22.20 22.21 22.22 22.23 22.24 22.25

4


DN09142359


DN09142359

22.26

Contents of the IDC_ Roof kit (IRSA) delivery . . . . . . . . . . . . . . . . . . . 238

23 23.1 23.2

Appendix Installation tools and torque values . . . . . . . . . . . . . . . . . . . 239 BTS installation tools and equipment. . . . . . . . . . . . . . . . . . . . . . . . . . 239 Torque values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240


5


List of figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45

6

Location of the System Extension Module in stacked installations . . . . . 16 Connecting System Extension Module cabling. . . . . . . . . . . . . . . . . . . . 17 Example: installing the FSEC on the installation plate . . . . . . . . . . . . . . 19 Threading the straining strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Installing the FPIA to the pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Flexi Mounting Auxiliary Brackets (FMAA) . . . . . . . . . . . . . . . . . . . . . . . 22 Fixing maintenance strap to back cover . . . . . . . . . . . . . . . . . . . . . . . . . 24 Snap hook fixing point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Fixing maintenance strap to front cover . . . . . . . . . . . . . . . . . . . . . . . . . 27 Hook fixing point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Cable tunnels (3U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Stack installation with cable tunnels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Two FPMAs stacked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Positive grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 FPMA provisioning for configurations with one FPMA . . . . . . . . . . . . . . 34 FPMA provisioning for configurations with two FPMAs . . . . . . . . . . . . . 34 FPMA provisioning for configurations with new and old version FPMA . 34 FPMA provisioning for configurations with two FPMAs . . . . . . . . . . . . . 35 Connecting grounding cable and installing DC cable harness . . . . . . . . 35 Removing the ingress protection plate . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Removing the AC terminal enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Detaching the AC terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Routing the AC cable through the ingress protection plate. . . . . . . . . . . 38 Single phase connection 230 V AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 3-phase star connection 230 V AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3-phase delta connection, base voltage 100-120 V AC (200-240 V AC potential difference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3-phase delta connection 110 V AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Installing sub-modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Changing the FPAA fan airflow direction (Acbel) . . . . . . . . . . . . . . . . . . 41 Changing the FPAA fan airflow direction (Efore) . . . . . . . . . . . . . . . . . . 41 Connecting the AC cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Connecting the alarm cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Connecting the DC cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Replacing the ingress protection plate . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Installing cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Installing second FPMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Installing second FPMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Connecting the DC power feed cable (FSMB/C/D/E) . . . . . . . . . . . . . . . 47 Connecting the DC power feed cable (FSMF) . . . . . . . . . . . . . . . . . . . . 47 Example configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Connector removed from cable 994808 . . . . . . . . . . . . . . . . . . . . . . . . . 50 Stripped power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Detached DC cable harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Removed rubber boots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Removed cable terminals, washers and nuts . . . . . . . . . . . . . . . . . . . . . 52


DN09142359


Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 70 Figure 71 Figure 72 Figure 73 Figure 74 Figure 75 Figure 76 Figure 77 Figure 78 Figure 79 Figure 80 Figure 81 Figure 82 Figure 83 Figure 84 Figure 85 Figure 86 Figure 87 Figure 88 Figure 89

DN09142359

Rubber boot heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Cutting the rubber boots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Routing the power cables through the rubber boots . . . . . . . . . . . . . . . 53 Stripping the - cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Attaching the protection tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Cable terminals attached . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Using plastic insulation bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Fixing the power cables to DC connectors . . . . . . . . . . . . . . . . . . . . . . 56 Attaching the rubber boots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 DC cable harness power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Removing the rubber boots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Connecting power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Powering two System Modules with one FPMA . . . . . . . . . . . . . . . . . . 60 Front panel of the FPDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 FPDA provisioning for configurations with one FPDA . . . . . . . . . . . . . . 61 FPDA provisioning for configurations with two FPDAs . . . . . . . . . . . . . 62 FPDA provisioning for configurations with three FPDAs and two System Modules (sample 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 FPDA provisioning for configurations with three FPDAs and two System Modules (sample 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 FPDA provisioning for configurations with three FPDAs and one System Module (sample 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 FPDA provisioning for configurations with four FPDAs and two System Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Parallel FPDAs with paired (chained) DC cables and boots . . . . . . . . . 64 Fixing cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Connecting grounding cable to plinth . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Connecting DC output cables to FPDA . . . . . . . . . . . . . . . . . . . . . . . . . 67 Connecting alarm cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 AC interface support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Opening the AC connector cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Loosening the AC cable clamp screws . . . . . . . . . . . . . . . . . . . . . . . . . 74 AC cable routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Cabling completed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Closing the AC connector cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Marking the fixing points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Opening the AC connector cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Loosening the AC cable clamp screws . . . . . . . . . . . . . . . . . . . . . . . . . 80 AC cable routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Cabling completed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Closing the AC connector cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Fixing points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 FPAC installed using the right-hand side fixing points. . . . . . . . . . . . . . 84 Opening the AC connector cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Loosening the AC cable clamp screws . . . . . . . . . . . . . . . . . . . . . . . . . 86 AC cable routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Wires connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Closing the AC connector cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89


7


Figure 90 Figure 91 Figure 92 Figure 93 Figure 94 Figure 95 Figure 96 Figure 97 Figure 98 Figure 99 Figure 100 Figure 101 Figure 102 Figure 103 Figure 104 Figure 105 Figure 106 Figure 107 Figure 108 Figure 109 Figure 110 Figure 111 Figure 112 Figure 113 Figure 114 Figure 115 Figure 116 Figure 117 Figure 118 Figure 119 Figure 120 Figure 121 Figure 122 Figure 123 Figure 124 Figure 125 Figure 126 Figure 127 Figure 128 Figure 129 Figure 130 Figure 131 Figure 132 Figure 133 Figure 134 Figure 135 Figure 136

8

AC cable clamp screws fixed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Marking the fixing points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Opening the AC connector cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Loosening the AC cable clamp screws . . . . . . . . . . . . . . . . . . . . . . . . . . 93 AC cable routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Wires connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Closing the AC connector cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 AC cable clamp screws fixed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Fixing points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 FPAD installed using the right-hand side fixing points . . . . . . . . . . . . . . 97 Flexi Power Distribution and Fuses Outdoor (FPFC) . . . . . . . . . . . . . . . 99 FPFC installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 FPFC grounding points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 EAC cable routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Cable outer jacket stripping (input from right-hand side) . . . . . . . . . . . 102 Cable outer jacket stripping (input from left-hand side) . . . . . . . . . . . . 103 Three-fingered cold shrink tube installed . . . . . . . . . . . . . . . . . . . . . . . 103 Cable diameters for input IP boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Cable diameter >25 mm (1 in.) (input from right-hand side) . . . . . . . . . 104 Cable diameter >25 mm (1 in.) (input from left-hand side) . . . . . . . . . . 105 Cable diameter <25 mm (1 in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Input cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Fixing the input cable connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Typical input cabling from right-hand side for single FPFC . . . . . . . . . 107 FPFC input cabling from both sides . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Cable outer jacket stripping (output from right-hand side) . . . . . . . . . . 109 Cable outer jacket stripping (output from left-hand side) . . . . . . . . . . . 109 Three-fingered cold shrink tube installed . . . . . . . . . . . . . . . . . . . . . . . 109 IP boot cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Cable diameter >25 mm (1 in.)(output from right-hand side) . . . . . . . . 110 Cable diameter >25 mm (1 in.) (output from left-hand side) . . . . . . . . . 110 Cable diameter <25 mm (1 in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Output cable connectors and GND, max values . . . . . . . . . . . . . . . . . . 111 Fixing the output cable connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Cable routing in 2U casing with left-hand side input cabling. . . . . . . . . 112 On/Off bar ‘On’ position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Adjusting the output current knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Two FPFCs chained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Installation example with three RF Modules . . . . . . . . . . . . . . . . . . . . . 116 FMAA with two FSECs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 FMAA with FSEB and FSEC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 FSEC fixing points on the FCOA roof . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Opening FSEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Removing protector board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Installing FSEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Installing FPIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Connecting grounding cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121


DN09142359


Figure 137 Figure 138 Figure 139 Figure 140 Figure 141 Figure 142 Figure 143 Figure 144 Figure 145 Figure 146 Figure 147 Figure 148 Figure 149 Figure 150 Figure 151 Figure 152 Figure 153 Figure 154 Figure 155 Figure 156 Figure 157 Figure 158 Figure 159 Figure 160 Figure 161 Figure 162 Figure 163 Figure 164 Figure 165 Figure 166 Figure 167 Figure 168 Figure 169 Figure 170 Figure 171 Figure 172 Figure 173 Figure 174 Figure 175 Figure 176 Figure 177 Figure 178 Figure 179 Figure 180 Figure 181 Figure 182

DN09142359

Connecting DC cable to FSEC from RF or System Module . . . . . . . . Connecting DC cable to RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting DC feeder cable to FSEC (6Yxxxxxxxxx) . . . . . . . . . . . . . 48V system floating or 48V system positive grounding . . . . . . . . . . . . +24V/48V system, negative grounding . . . . . . . . . . . . . . . . . . . . . . . . Connecting DC cable to System Module . . . . . . . . . . . . . . . . . . . . . . . Connecting alarm cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Closing FSEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FSES interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing FSES on casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting FSES grounding cable to plinth . . . . . . . . . . . . . . . . . . . . Removing FSES IP boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wrapping tape around shielded DC cable . . . . . . . . . . . . . . . . . . . . . . Wrapping an extra tape around DC cable . . . . . . . . . . . . . . . . . . . . . . Inserting DC power cable to IP boot . . . . . . . . . . . . . . . . . . . . . . . . . . Removing narrow end of IP boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Properly secured shielded DC cable (left) and non-shielded DC cable (right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting DC feeder cable wires . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixing IP boot screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixing DC feeder cable to cable entry . . . . . . . . . . . . . . . . . . . . . . . . . Fixing DC power cable with cable tie . . . . . . . . . . . . . . . . . . . . . . . . . . Removing alarm port IP boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing IP plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting alarm cable to IP boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting alarm cable wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixing alarm cable IP boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two FSES’s stacked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example of FCIA rooftop installation . . . . . . . . . . . . . . . . . . . . . . . . . . Example of FCOA rooftop installation (with FSEB and FSEC) . . . . . . FSES installed on FPIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two FSES’s on FPIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four FSES’s on FPIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flexi Fiber Optical Distribution unit (FODA). . . . . . . . . . . . . . . . . . . . . Outdoor installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation example with FODA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opening the lid of FODA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Routing cables through the cable gland . . . . . . . . . . . . . . . . . . . . . . . Routing fibers inside FODA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tightening the cable gland. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixing the mounting brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing FODA in a 3U casing together with FPFC . . . . . . . . . . . . . . Installing FODA on top of a casing. . . . . . . . . . . . . . . . . . . . . . . . . . . . Opening the lid of FODA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Routing cables through the cable gland . . . . . . . . . . . . . . . . . . . . . . . Tightening the cable gland. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixing the mounting bracket and the cable tie bracket. . . . . . . . . . . . .


122 123 123 124 124 125 126 127 128 129 130 131 131 132 132 133 134 134 135 135 136 136 137 137 138 138 139 140 141 142 143 144 145 146 147 148 149 149 150 151 151 152 153 154 155 155

9


Figure 183 Figure 184 Figure 185 Figure 186 Figure 187 Figure 188 Figure 189 Figure 190 Figure 191 Figure 192 Figure 193 Figure 194 Figure 195 Figure 196 Figure 197 Figure 198 Figure 199 Figure 200 Figure 201 Figure 202 Figure 203 Figure 204 Figure 205 Figure 206 Figure 207 Figure 208 Figure 209 Figure 210 Figure 211 Figure 212 Figure 213 Figure 214 Figure 215 Figure 216 Figure 217 Figure 218 Figure 219 Figure 220 Figure 221 Figure 222 Figure 223 Figure 224 Figure 225 Figure 226 Figure 227 Figure 228

10

Installing FODA on wall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Installing the front cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Opening the lid of FODA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Routing cables through the cable gland . . . . . . . . . . . . . . . . . . . . . . . . 159 Tightening the cable gland . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Fixing the mounting bracket and the cable tie bracket . . . . . . . . . . . . . 160 Installing FODA on a pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Installing the front cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 FMAA with FSEB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 FMAA with FSEB and FSEC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 FSEB fixing points on the FCIA roof . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 FSEB fixing points on the FCOA roof . . . . . . . . . . . . . . . . . . . . . . . . . . 166 FSEB installed horizontally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 FSEB installed vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 FSEB connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Fixing FSEB cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Install FSEB with four M5 screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Connect the grounding cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Jumper X1103 in 12 Alarms mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Connect the external alarms cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Control outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Install the cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 FSEB printed wiring board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 GPS hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 GPS view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Installing the GPS/GNSS system on the wall . . . . . . . . . . . . . . . . . . . . 182 Installing the GPS/GNSS system on the pole . . . . . . . . . . . . . . . . . . . . 182 Pole mounting bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Pole mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 FYEA fixing points on the FCOA roof . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Opening the FYEA lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Threading the straining strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Connecting the grounding cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 Exposing the wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 Connecting cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 Connecting cable shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Closing the FYEA lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Flexi GPS Box (FYGD) front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Removing dummy unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 Fixing FYGD to core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 1PPS connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Connecting sync cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Side kits fixed to the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Installing an OSKA Side Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 IRSA Roof Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Fitting the support, mounting rails and adapter plate to the IDCA cabinet . 202


DN09142359


Figure 229 Figure 230 Figure 231 Figure 232 Figure 233 Figure 234 Figure 235 Figure 236 Figure 237 Figure 238 Figure 239 Figure 240 Figure 241 Figure 242 Figure 243 Figure 244 Figure 245 Figure 246 Figure 247 Figure 248 Figure 249 Figure 250 Figure 251 Figure 252

DN09142359

Mounting the FPRA on the adapter plate . . . . . . . . . . . . . . . . . . . . . . Fitting the masks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FPRA installation in forward position . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the FPIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the FMAA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the back and front covers . . . . . . . . . . . . . . . . . . Delivery contents of the back and front covers . . . . . . . . . . . . . . . . . . EMHA delivery contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EMTA delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FMSC delivery contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the FPMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the FPAA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the FPBA/B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the FPDA delivery . . . . . . . . . . . . . . . . . . . . . . . . FPAC delivery contents (FPAC top view) . . . . . . . . . . . . . . . . . . . . . . FPAD delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FPFC delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FSEC delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FSES delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FODA delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery contents of the FSEB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GPS hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FYEA delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GPS Box (FYGD) delivery contents. . . . . . . . . . . . . . . . . . . . . . . . . . .


203 204 205 209 210 211 212 214 216 219 221 222 222 223 224 225 227 228 229 230 231 233 234 236

11


List of tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Table 18 Table 19 Table 20 Table 21 Table 22 Table 23 Table 24 Table 25 Table 26 Table 27 Table 28 Table 29 Table 30 Table 31 Table 32 Table 33 Table 34 Table 35 Table 36 Table 37 Table 38 Table 39 Table 40 Table 41 Table 42 Table 43 Table 44

12

Maximum sizes of conductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 End stage output DC cable thickness per number of FPAAs . . . . . . . . 34 Input cable application cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Output cable application cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 EACX connector I pin assignment (Sub-D37) . . . . . . . . . . . . . . . . . . . 175 EACX connector II pin assignment (Sub-D37) . . . . . . . . . . . . . . . . . . . 176 Screw terminal pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Fire detector power screw terminal X4114 pin assignment . . . . . . . . . 178 EAC cable (FTSI) wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 GPS/GNSS pole mounting band cutting rule . . . . . . . . . . . . . . . . . . . . 183 FYEA connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 System Extension Kit (FSKA) delivery content . . . . . . . . . . . . . . . . . . 207 System Extension Kit (FSKB) delivery content . . . . . . . . . . . . . . . . . . 208 The Flexi Pole Installation Kit (FPIA) delivery content . . . . . . . . . . . . . 209 Flexi Mounting Auxiliary Bracket (FMAA) delivery contents . . . . . . . . 210 3U mounting covers (FMCA) delivery content . . . . . . . . . . . . . . . . . . . 211 The Flexi Mounting Covers Front and Back, 2U (FMCB), needed with Flexi Power DC/ DC Module 24 V (FPDA) . . . . . . . . . . . . . . . . . . . . . . . . . . 212 The Flexi Module Casings for 3U modules (EMHA) delivery contents 213 The Flexi Module Casings for 2U modules (EMTA) delivery contents . 215 Flexi Side Covers (FMHA) delivery content . . . . . . . . . . . . . . . . . . . . . 217 Flexi Side Covers (FMTA) delivery content . . . . . . . . . . . . . . . . . . . . . 218 Flexi Mounting Shield 3U Casing (FMSC) delivery contents . . . . . . . . 219 The Power Module (FPMA) delivery content . . . . . . . . . . . . . . . . . . . . 220 The FPAA power sub-module delivery content . . . . . . . . . . . . . . . . . . 221 The FPBA/B power sub-module delivery content . . . . . . . . . . . . . . . . 222 The 24V Power Module (FPDA) delivery content . . . . . . . . . . . . . . . . 223 Flexi Power AC/DC sub-module 230V (FPAC) delivery content . . . . . 224 Flexi Power AC/DC sub-module (FPAD) delivery content . . . . . . . . . 225 Flexi Power Distribution and Fuses Outdoor (FPFC) delivery content 226 Flexi System External OVP (FSEC) delivery content . . . . . . . . . . . . . 228 Flexi System External OVP (FSES) delivery content . . . . . . . . . . . . . . 229 Flexi Fiber Optical Distribution unit (FODA) delivery content . . . . . . . . 230 Flexi System External Alarm Module (FSEB) delivery contents . . . . . 231 GPS Mounting Kit (FYMA) delivery content . . . . . . . . . . . . . . . . . . . . . 232 GPS Antenna Kit (FYGA) delivery content . . . . . . . . . . . . . . . . . . . . . 232 GPS GLONASS Receiver Antenna (FYGB) delivery content . . . . . . . 232 GPS cable deliveries (FYHA/FYHB/FTSE/FTSH) . . . . . . . . . . . . . . . 232 Flexi GPS Surge Protection Kit (FYEA) delivery content . . . . . . . . . . . 234 Flexi System Alarm Cable (FSAA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 GPS Box (FYGD) delivery content . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 Delivery contents of the outdoor side kit (OSKA) . . . . . . . . . . . . . . . . . 237 IDC_ Roof Kit (IRSA) delivery contents . . . . . . . . . . . . . . . . . . . . . . . . 238 Tools for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Torque values for the BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240


DN09142359


Summary of changes

Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. This document is published with the product releases listed in the following table. Radio Access Technology (RAT)

Product release

GSM

RG30

WCDMA

RU40 RU50

LTE

RL35TD RL40 RL50

Table

RAT releases covered by the document

Changes between issues 01 (2013-06-13) and 01A (2013-09-18) Installing System Extension Module (1) •

References to System Module variants FSMG and FSML removed.

Installing Flexi Power AC/DC sub-module (FPAC) to a pole-mounted RRH (10.2) •

FPKC removed.

Installing Flexi Power AC/DC sub-module (FPAD) to a pole-mounted RRH (11.2) •

FPKC removed.

Installing GPS Antenna Kit (FYGA) or GPS GLONASS Receiver Antenna (FYGB) (17) •


Installing Flexi GPS Box (FYGD) (19) •

Front panels in Figure 220 Flexi GPS Box (FYGD) front panel, Figure 223 1PPS connection and Figure 224 Connecting sync cable updated.

Contents of the Flexi Mounting Auxiliary Bracket (FMAA) (22.4) •

Screw information in Table 15 Flexi Mounting Auxiliary Bracket (FMAA) delivery contents updated.

Contents of the GPS hardware deliveries (22.21) •


Contents of the GPS Box (FYGD) delivery (22.24) •

DN09142359

Front panel in Figure 252 GPS Box (FYGD) delivery contents updated.

Id:0900d80580a2accc Confidential

13

Summary of changes

14


Id:0900d80580a2accc Confidential

DN09142359


Installing System Extension Module

1 Installing System Extension Module Purpose The System Extension Module is a System Module without a transmission sub-module. The System Module can be used as a System Extension Module operating in a baseband extension mode to add channel capacity. In this case, it is connected to the System Module by connecting two optical cables and a DC cable. These items are provided with Flexi System Extension Kit (FSKA) 471226A delivery that includes: •

•

cable set assembly: • 2 x optical cable, 2 m (6.6 ft.) • 1 x power cable, 2 m (6.6 ft.) • 4 x optical transceiver transmission dummy panel

Also Flexi System Extension Kit (FSKB) 472302A is available. It is otherwise the same as FSKA, but with 4 meter (13.1 ft.) cables. The System Extension Module does not have a transmission sub-module. Instead, a dummy transmission sub-module is installed to provide IP protection.

w

NOTICE: Risk of damage to equipment. If you are reusing a Master System Module as a System Extension Module, remove the transmission sub-module before installing it. Before you start The module itself is installed the same way as the other modules. For more information on installation, see Installing Flexi Multiradio 10 BTS for Stack, Wall, and Pole Configurations. Steps

1

Install the System Extension Module casing. In stacked installations, the System Extension Module is installed on top of the module stack.

DN09142359

Id:0900d80580a2abc3 Confidential

15



System Extension Module (optional)

RF Module 3

RF Module 2 Transmission sub-module System Module

RF Module 1

Power Module (optional) Plinth Figure 1 2

Location of the System Extension Module in stacked installations

Install the dummy panel on the top right corner of the System Extension Module core. a) Install the dummy panel: 1. Align the dummy panel with the guide pin in the System Module. 2. Push the dummy panel in place. 3. Fix the dummy panel with 4 x M5x25 screws. 4. Tighten to 2.2 Nm (1.6 ft-lb).

w

NOTICE: Risk of damage to equipment. Check that the ingress protection (IP) gasket remains in its place and install the dummy panel on top of it to make sure that the ingress protection works properly.

3

Connect one end of the DC cable to the System Extension Module DC connector and the other end to the connector marked with EXT on the System Module front panel. Route the DC cable via external cable entries. Fix any excess cable on the sides of the module casings. For information on connecting the FMSF DC cable, see Connecting external power feed in Cabling Flexi Multiradio 10 BTS. For information on connecting the FSMC/D/E DC

16


DN09142359



cable, see Connecting external power feed in Cabling Flexi Multiradio BTS LTE and Creating Configurations..

Figure 2

Connecting System Extension Module cabling

Further information For more information on connecting the DC cable, see FPFD interfaces and electrical connections in Flexi Multiradio 10 BTS System Module Description. 4

Install the optical transceivers (two to the Master System Module and two to the System Extension Module). For further information on how to install the optical transceivers for System Module variant FSMF, see Connecting internal optical cables in Cabling Flexi Multiradio 10 BTS. For information on installing these for FSMC/D/E, see Connecting internal optical cables in Cabling Flexi Multiradio BTS LTE and Creating Configurations.

5

Connect an optical cable from the OPT1 connector to the OPT1 connector on the System Extension Module. Make sure that all connector seals are firmly in place.

DN09142359


17



Note that OPT1 and OPT2 from the Master System Module have to be connected to OPT1 and OPT2 on the System Extension Module respectively. 6

18

Repeat for the second optical cable (OPT2 connectors).


DN09142359


Installing Flexi Pole Installation Kit (FPIA)

2 Installing Flexi Pole Installation Kit (FPIA) Purpose Flexi Pole Installation Kit (FPIA) is used for installing the following auxiliary units to a pole: • • • •

Flexi System External Alarm (FSEB) Flexi System External OVP (FSEC) Flexi System External OVP (FSES) Flexi GPS Surge Protection Kit (FYEA)

The pole can between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter. The recommended torque value for fixing the FPIA is 5.0-8.0 Nm (3.7 - 5.9 ft-lb.). Steps 1

Install the auxiliary unit to the installation plate using four screws. The installation orientation can be either horizontal or vertical depending on the requirements of the auxiliary unit.

DN70458321

Figure 3

DN09142359

Example: installing the FSEC on the installation plate

Id:0900d805809aaacd Confidential

19


2


Thread the straining strap to the installation plate.

2

DN70458333

Figure 4

20

Threading the straining strap


DN09142359


3


Install the installation plate to the pole with the straining strap.

4 3

DN70458345

Figure 5 4

DN09142359

Installing the FPIA to the pole

Tighten the straining strap around the pole.


21

Installing Flexi Mounting Auxiliary Brackets (FMAA)


3 Installing Flexi Mounting Auxiliary Brackets (FMAA) Purpose Flexi Mounting Auxiliary Brackets (FMAA) can be used to mount auxiliary units on casings in pole, wall and stack configurations. The brackets are mounted on the casing using the existing connection pin holes. The FMAA can be used with the following auxiliary units: • • •

Flexi System External Alarm (FSEB) Flexi System External OVP (FSEC) Flexi GPS Surge Protection Kit (FYEA)

The mounting holes for the most common installation position for each auxiliary unit are labelled on the bracket. Summary

Spring washer

Figure 6

Flexi Mounting Auxiliary Brackets (FMAA)

Steps

22

1

Remove the four connection pins from the casing on which the FMAA is to be installed.

2

Align the outer holes of each bracket with the connection pin holes.

Id:0900d80580a2b4ea Confidential

DN09142359


3

Use the M5 X 6 screws to mount each bracket to the casing.

4

To mount the auxiliary unit on the brackets, see the following installation instructions: • •

DN09142359

Installing Flexi Mounting Auxiliary Brackets (FMAA)

Installing Flexi System External Alarm (FSEB) Installing Flexi System External OVP (FSEC)

Id:0900d80580a2b4ea Confidential

23

Installing back covers


4 Installing back covers Purpose Module back and front covers provide IP20 protection for core modules. Install the back covers before installing the modules. Note also that some radio modules are delivered without casing. If also optional front and back covers are needed, you should order the 3U Module Casing (EMHA, 470316A). EMHA contains also the front and back covers. For information on casing and cover kits need for modules, see Appendix Casing and cover kits need for Flexi Multiradio units in Installing Flexi Multiradio BTS LTE Modules in Cabinets document.

f

CAUTION! Risk of personal injury. Rotating fan blades can cause personal injury. If Flexi BTS modules are not installed in a cabinet, back covers must be used during operation for safety reasons and should only be removed temporarily for maintenance. Before you start

t

When there is no risk of dropping the covers, maintenance straps are not needed. Maintenance straps can be attached to both ends of the module casing. Steps

1

Thread the longer loop of the maintenance strap around the grill rib. To secure the strap firmly in place use the rib with the wall.

Figure 7

Fixing maintenance strap to back cover

2

Route the end with the snap hook through the exposed loop and tighten the loop.

3

Engage the snap hook to the casing. Use the fixing point shown in Figure 8 Snap hook fixing point.

24

Id:0900d805809ec942 Confidential

DN09142359


Figure 8 4


Snap hook fixing point

Install the back cover in the rear of the module. Make sure that the maintenance strap remains behind the plastic wall.

DN09142359


25


5

26


Fix the back cover screws (Torx T25) and tighten to 2.5 Nm (1.8 ft-lb).


DN09142359


Installing front covers

5 Installing front covers Purpose Module back and front covers provide IP20 protection for core modules. Note also that some radio modules are delivered without casing. If also optional front and back covers are needed, you should order the 3U Module Casing (EMHA, 470316A). EMHA contains also the front and back covers. For information on casing and cover kits need for modules, see Appendix Casing and cover kits need for Flexi Multiradio units in Installing Flexi Multiradio BTS LTE Modules in Cabinets document.

f

CAUTION! Risk of personal injury. The front panels of the modules are hot during operation. If Flexi BTS modules are not installed in a cabinet, front covers must be used during operation for safety reasons and should only be removed temporarily for maintenance. Before you start

t

When there is no risk of dropping the covers, maintenance straps are not needed. Steps

1

Thread the longer loop of the maintenance strap around the grill rib on the front cover.

Figure 9 2

DN09142359

Fixing maintenance strap to front cover

Route the end with the snap hook through the exposed loop and tighten the loop.

Id:0900d805809a4bd0 Confidential

27

Installing front covers

3


Engage the hook to the hole on the external cable entry.

Figure 10 4

28

Hook fixing point

Install the front cover and tighten the screws (Torx 25) to 2.5 Nm (1.8 ft-lb.).

Id:0900d805809a4bd0 Confidential

DN09142359


Installing optional side cable tunnels

6 Installing optional side cable tunnels Purpose You can use the optional cable tunnels to hide excess cabling on the side of stack or pole configurations. Cable tunnels are not required for weather protection. Note that Flexi BTS Side Covers FMTA for 2 height units (2U) and Flexi BTS Side Covers FMHA for 3 height units (3U) must be ordered separately. The codes are: 471523A (FMTA) and 471524A (FMHA). Before you start Check that cables are installed and routed. Summary

Removable knockout

Figure 11

Cable tunnels (3U)

Steps 1

Remove the knockouts from the cable tunnel as required by the position of the tunnel. • • • •

2

Pre-thread the M5 X 10 screws into the cable tunnel.

3

Position the cable tunnel over the cable support plate so that the cable tunnel screws are aligned with the plate fixing points, and tighten the screws.

g 4

DN09142359

For all external cable tunnels on the right side, remove the back knockout. For the top internal cable tunnel on the left side, remove the bottom knockout. For the bottom internal cable tunnel on the left side, remove the top knockout. For the remaining internal cable tunnels on the left side, remove the top and bottom knockouts.

If you are using a plastic cable support plate fix the cable tunnel with M5 self-tapping screws. If you are using a metallic cable support plate fix the cable tunnel with M5 screws.

Remove the pre-installed screws from the front cover.


29

Installing optional side cable tunnels


5

Position the cable tunnel front pieces over the front cover so that each cable tunnel front piece hole is aligned with the front cover holes.

6

Pre-thread M5 screws that came with the accessory bag through both covers so that the cable tunnel front piece is connected to the front cover.

g

The M5 screws that came in the accessory bag have threading closer to the end of the screw. The M5 screws that came pre-installed on the front covers have threading closer to the middle and do not work with the cable tunnels.

7

Align the front cover screws with the cable entry fixing points and tighten the screws.

8

Repeat steps 2-7 for each casing. Expected outcome

DN70125481

Figure 12

30

Stack installation with cable tunnels


DN09142359


Installing Flexi Power Module (FPMA)

7 Installing Flexi Power Module (FPMA) 7.1

Installing Flexi Power Module (FPMA) Purpose Flexi Multiradio BTS uses 48 VDC power. In a BTS site with AC feed only, a Flexi Power Module (FPMA) is required for converting the AC to DC before feeding the DC power to the System Module. Flexi Power Module (FPMA) consists of mechanics, AC terminal and four slots for AC/DC sub-module (FPAA) or battery sub-module (FPBA/B). The FPMA can include: • • • •

w

two FPAAs and two FPBAs or FPBBs four FPAAs one FPAA and three FPBAs or FPBBs. Remember to take the charging current into account when dimensioning the rectifiers and batteries. one FPAA and three free slots for expansion.

NOTICE: Do not install the FPBA and FPBB in parallel. If used in parallel, one of these two battery types discharges faster than the other causing an unbalance between the batteries. Two FPMAs can be installed in a stack to support FPAA and FPBA/B operating in parallel.

DN09142359


31



AC distribution

FPXX

FPXX

FPXX

FPXX

AC distribution

FPXX

FPXX

FPXX

FPXX

Figure 13

75A to System Module

Two FPMAs stacked

If your configuration includes a System Extension Module, utilize the additional ground lugs attached to the DC cable harness. Tighten the nuts to 14 Nm (10 ft-lb.). By default, the DC output voltage of the FPMA is floating nominal 48 VDC, however, it can also be positive grounded. This can be implemented by using a branch connector in an additional connection box (see Figure 14 Positive grounding). In this solution, the + wire between the FPMA and System Module is cut, and grounding to the BTS site ground bar is done with an additional grounding cable (the cross-section of which must be the same as that of the + wire).

32


DN09142359


Figure 14


Positive grounding

The maximum diameter of the AC power feed cable is 24 mm (0.9 in). The maximum sizes of conductors that the incoming AC terminals can accommodate are presented in Table 1 Maximum sizes of conductors. Rated connecting capacity

Value

Rigid (solid or stranded)

up to 16 mm2 (6 AWG)

Flexible


Flexible with ferrule (without plastic sleeve) up to 10 mm2 (7 AWG) Flexible with ferrule (with plastic sleeve)


Flexible with TWIN ferrule

up to 6 mm2 (9 AWG)

Table 1

t

Maximum sizes of conductors

It is recommended that the FPMA be pre-installed before installing it on the plinth. If applicable, multiple FPMAs can be installed to FPMA unit to support FPAA&FPBA/ FPBB connection in parallel. A maximum of two DC cables can be installed together at each output terminal. This limitation is caused by: •

• •

The output current from the FPMA where two with more than 4 FPAAs are combined would exceed the safety limits for the thickness of the DC cables provided in the delivery. The safety rubber boots provided in the delivery can accommodate up to two DC cables per terminal. The DC output terminal bolt length can accommodate up to two DC cables per terminal.

Figures FPMA provisioning for configurations with one FPMA through FPMA provisioning for configuration with new and old version FPMA show examples of FPMA provisioning based on the number of FPMAs.

DN09142359


33



AC

Circuit break

Figure 15

FPMA (204)

48V DC

Circuit break

AC

FPMA (204)

48V DC

Circuit break

AC

FPMA (204)

48V DC

Circuit break

AC

FPMA (101-103)

48V DC

34

System Module

FPMA provisioning for configurations with new and old version FPMA

When FPMAs are installed in parallel, the DC output cables should be installed together at the FPMA closest to the System Module. When these two FPMAs have more than four FPAAs, two additional cable lugs are required for the second stage FPMA output. These cable lugs are not included in the delivery and must be sourced locally, choose appropriate thickness of the DC cables based on the number of FPAAs. See Table 2 End stage output DC cable thickness per number of FPAAs for details. Maximum output current

End stage output cable recommendation thickness

Fewer than 4 FPAAs

74 A

Default (25 mm2) (4 AWG)

5 FPAAs

92.5 A

35 mm2 (2 AWG)

6 FPAAs

111 A

50 mm2 (1 AWG)

7 FPAAs

129.5 A

50 mm2 (1 AWG)

8 FPAAs

148 A

50 mm2 (1 AWG)

Table 2

•

System Module

FPMA provisioning for configurations with two FPMAs

The quantity of FPAAs in FPMA configuration

•

System Module

FPMA provisioning for configurations with one FPMA AC

Figure 17

•

48V DC

Circuit break

Figure 16

•

FPMA (101->)

End stage output DC cable thickness per number of FPAAs

When there are 8 FPAAs in FPMAs in parallel mode, two additional 50 mm2 (1 AWG) cables are required for the end stage FPMA. New version FPMAs can be compatible with the old version FPMAs as old version is used as the first stage.


DN09142359


•


When FPMAs are operated in parallel the alarm connection between FPMA and System Module can be made in alternative ways. See Figure 18 FPMA provisioning for configurations with two FPMAs. Black line routing shows the primary connection and the black dotted line the alternative connection.

DC

AC

AC

Figure 18

Alternative connection

System Module

DC

FPMA provisioning for configurations with two FPMAs

Steps 1

Install the Flexi Power Module (FPMA) and ground it.

System Mod

ule 1

Figure 19

DN09142359

Connecting grounding cable and installing DC cable harness


35


2


Install the DC cable harness inside the FPMA, on the right-hand side. Fix with one screw (note that if cable entries are used with the FPMA, the same screw also holds the cable entry in place).

3

Remove the ingress protection plate by undoing the screws holding the plate in place.

System

Module

Sy

3

ste

m

Mo

du

le

3

Figure 20

36

Removing the ingress protection plate


DN09142359


4


Undo the screw from the top left corner of the AC terminal enclosure and pull it out.

System

Module

4

Figure 21 5

Remove the cover of the AC terminal enclosure by undoing the four screws.

6

Detach the AC terminal from the enclosure by undoing the two screws at the bottom of the enclosure.

Figure 22

DN09142359

Removing the AC terminal enclosure

Detaching the AC terminal


37


7


Route the AC cable through the round hole in the top left corner of the ingress protection plate.

Figure 23

Routing the AC cable through the ingress protection plate

8

Route the AC cable through the cable clamp on the AC terminal.

9

Make the AC connection. Tighten the screws to 1.8 Nm (1.3 ft-lb.).

f

WARNING! Danger of lethal voltages. Switch off the AC power breaker before connecting the AC cable. See figures Figure 24 Single phase connection 230 V AC, Figure 25 3-phase star connection 230 V AC, Figure 26 on page 39, and Figure 27 3-phase delta connection 110 V AC for AC connection alternatives. The alternatives are also shown on the label on the inside of the AC terminal enclosure cover. The colors of the wires may vary depending on the country.

Figure 24

38

Single phase connection 230 V AC


DN09142359


g

For a 3-phase star connection, remove the bridge by loosening the screws behind L1L3.

Figure 25

g

DN09142359

3-phase star connection 230 V AC

For a 3-phase delta connection, remove the bridges by loosening the screws behind L1L3 and N1-N3.

Figure 26

g


3-phase delta connection, base voltage 100-120 V AC (200-240 V AC potential difference)

For a 3-phase delta connection (110 V AC) connect the bridges for terminals L1-L3 and N1-N3. See Figure 27 3-phase delta connection 110 V AC.


39


Figure 27 10


3-phase delta connection 110 V AC

If required, install a Surge Protection Device (SPD). FPMA supports the use of surge protection device (SPD), if it is required.

11

Reinstall the AC terminal inside the enclosure and fix the two screws at the bottom.

12

Reinstall the cover of the enclosure and fix the four screws.

13

Push the AC terminal plate back into its slot and fix it with one screw in the top left corner.

System Module 15

13

Figure 28 14

14

Installing sub-modules

Install the FPAA sub-modules required by your configuration. The first or only FPAA must always be installed in the leftmost module slot. If there are empty slots, they must always be on the right. Note that if you are installing FPMA in a third-party cabinet, it may be necessary to change the FPAA cooling fan airflow direction from back-to-front to front-to-back. This is possible with FPAA 470140A.204 version. See the steps below on how to do this on Efore and Acbel FPAAs.

40


DN09142359



1. Remove the fan fixing screws. 2. Flip the fan so that the fan label is visible. 3. Fix the fan fixing screws back.

2

3 1

Figure 29

Changing the FPAA fan airflow direction (Acbel)

1

2

1

1

1

Figure 30 15

DN09142359

3

Changing the FPAA fan airflow direction (Efore)

Fix the FPAA screws.


41


16


Connect the AC cable from the FPAA to the FPMA AC terminal.

System

Modul

e

16 17

Figure 31 17

Connecting the AC cable

If you are using battery backup, install the FPBA/B sub-modules required by your configuration. Follow the same mechanical procedure as in FPAA installation.

18

If alarms from the FPMA to the System Module are needed, connect the alarm cables.

1 8a

1 8c 1 8b

Figure 32

w

Connecting the alarm cables

NOTICE: Connect the FPBB alarm cable to the FPAA, otherwise the FPBB LED does not work. a) Remove the ingress protection from the alarm cable connectors in FPAA and FPBA/B.

42


DN09142359



b) Chain the sub-modules together with the alarm cable from left to right. c) Connect the alarm cable from one of the sub-modules to the System Module. See Figure 18 FPMA provisioning for configurations with two FPMAs for more information. 19

Connect the DC cables to all the sub-modules.

19

Figure 33 20

Connecting the DC cables

Reinsert the ingress protection plate with cables routed through it as follows: a) Fix the grounding cable. b) Fix the screws.

2 0b

2 0a

Figure 34 21

Replacing the ingress protection plate

If applicable, install the cable entries. See Preparing the modules for a stand-alone installation for instructions.

DN09142359


43



21 21

Figure 35 22

Installing cable entries

If applicable, install a second FPMA on top of the first FPMA to support FPAA and FPBA/B connection in parallel. a) Cut the rubber boots of the DC cable harness (included in the accessory bag). Note that the cable terminals are included in the FPMA.

44


DN09142359


Figure 36


Installing second FPMA

b) Remove the rubber boots. c) Connect the power output cables ot the first FPMA to the DC cable harness of the second FPMA.

DN09142359


45


Figure 37


Installing second FPMA

d) Install the DC cable harness to the FPMA. e) Install the FPAA and/or FPBA/B sub-modules and connect the DC cable harness.

46


DN09142359


23


Route the DC power feed cables through the cable entries and connect them from the FPMA to the System Module.

23

23

Figure 38

Connecting the DC power feed cable (FSMB/C/D/E)

23

23

Figure 39

Connecting the DC power feed cable (FSMF)

24

Check that the cable connectors' seal caps are firmly in place.

25

Connect the mains power.

26

Power up the site. Make sure that the FPAA LED is yellow at this point.

27

Turn on the FPAA and FPBA/B by pushing the switch. Make sure that the FPAA LED is stable green and the FPBA/B LED is green and blinking slowly (charging).

DN09142359


47



To maximise the FPBA/B life-time, the charging current is limited. Therefore, it can take up to 12 hours to fully charge an empty FPBA/B. 28

If applicable, install the FPMA module covers. See Installing back covers and Installing front covers for instructions. If installing the front cover is required, fix the air deflector plate to the front cover first.

48


DN09142359


7.2

Powering an RF Module with a single FPMA equipped with one rectifier Purpose Follow these instructions to connect an RF Module to a single FPMA that has one rectifer (FPAA) installed. Before you start Perform the FPMA AC and rectifier cabling as instructed in Installing Flexi Power Module (FPMA). Steps

1

Connect the power cable to the RF Module. Use the longest cable from the DC cable harness to connect the closest RF Module directly from FPMA.

2

Complete the rest of the power cabling depending on the configuration. See Figure 40 Example configuration for an example configuration where the bottommost RF Module has been powered directly from FPMA using the longest cable of the DC cable harness.

System Module power cables

RF Module

Power Module

Plinth Figure 40

DN09142359

Example configuration


49


7.3

Powering an RF Module with a single FPMA equipped with 4 rectifiers/batteries Purpose Follow these instructions to connect an RF Module to a single FPMA that has four rectifiers/batteries installed. Before you start Perform the FPMA AC and rectifier/battery cabling as instructed in Installing Flexi Power Module (FPMA). Steps

1

Remove the multibeam connector from RF Module power cable. Remove the connector from the other end of cable 994808.

Figure 41 2

Connector removed from cable 994808

Strip the power cable. Strip the power cable approx. 120 - 150 mm (4.7. - 5.9 in.).

50


DN09142359


Figure 42 3

Detach the DC cable harness from FPMA.

Figure 43 4

Detached DC cable harness

Remove the rubber boots from the connectors.

Figure 44

DN09142359

Stripped power cable

Removed rubber boots


51


5

Remove the cable terminals, washers and nuts See figure below.

Figure 45 6

Cut the rubber boot heads off.

Figure 46 7

Removed cable terminals, washers and nuts

Rubber boot heads

Cut an entry through the rubber boots. Use, for example, a screwdriver to cut an entry to the rubber boots. See Figure 47 Cutting the rubber boots.

52


DN09142359


Be careful not to damage the rubber boots.

Figure 47 8

Route the RF Module power cables through the rubber boots.

Figure 48

DN09142359

Cutting the rubber boots

Routing the power cables through the rubber boots


53


9

Strip the + and - wires approx. 15 mm (0.6 in.).

Figure 49 10

Attach the protection tubes to the + and - wires.

Figure 50

54

Stripping the - cable

Attaching the protection tubes


DN09142359


11

Fix the cable terminals to + and - wires.

Figure 51 12

Fix the protection tubes using plastic insulation bands.

Figure 52

DN09142359

Cable terminals attached

Using plastic insulation bands


55


13

Fix the cables to the DC cable harness DC connectors.

Figure 53 14

Fixing the power cables to DC connectors

Attach the rubber boots back.

Figure 54

Attaching the rubber boots

15

Fix the DC cable harness back to the FPMA.

16

Connect the RF Module to FPMA. See Figure 55 DC cable harness power cables for information on module connections.

56


DN09142359


Figure 55

DN09142359

DC cable harness power cables


57


7.4

Powering two System Modules with a single FPMA Purpose Single FPMA installation can provide power to two System Modules. Follow these instructions to connect two System Modules to a single FPMA. Before you start Perform the FPMA AC and rectifier/battery cabling as instructed in Installing Flexi Power Module (FPMA). Steps

1

Detach the DC cable harness from FPMA.

2

Cut the rubber boots of the DC cable harness and remove them. See steps a) and b) in Figure 56 Removing the rubber boots.

Figure 56

58

Removing the rubber boots


DN09142359


3

Connect power cable 995069 to the DC cable harness. See step c) in Figure 57 Connecting power cables. Cable 995069 must be purchased separately.

Figure 57 4

Connecting power cables

Install the DC cable harness back to FPMA. See step d) in Figure 57 Connecting power cables.

5

Connect the System Module power cables. Figure 58 Powering two System Modules with one FPMA shows the power connection with two System Modules and a single FPMA. Note that two FPMA parallel operation is not possible in this configuration.

DN09142359


59


System Extension Module (optional)

RF Module 3

RF Module 2 Transmission sub-module System Module

RF Module 1

Power Module (optional) Plinth

Connection for first SM Connection for second SM Figure 58 Powering two System Modules with one FPMA

60


DN09142359


Installing Flexi Power DC/DC Module 24V (FPDA)

8 Installing Flexi Power DC/DC Module 24V (FPDA) Purpose The FPDA is an isolated 2U-high DC/DC Power Module that converts nominal 24 V DC input voltage to 48 V DC nominal output voltage and 2 kW power.

DC Input cabling

Alarm cabling

DC Output cabling

LED

GND Figure 59

Front panel of the FPDA

When the BTS power load is more than 2 kW, multiple FPDAs can be installed in parallel. When FPDAs are used in parallel, a maximum of two DC cables can be installed together at each output terminal. This limitation is caused by: • • •

The output current from the FPDA where all three are combined would exceed the safety limits for the thickness of the DC cables provided in the delivery. The safety rubber boots provided in the delivery can accommodate up to two DC cables per terminal. The DC output terminal bolt length can accommodate up to two DC cables per terminal.

Figures Figure 60 FPDA provisioning for configurations with one FPDA, Figure 61 FPDA provisioning for configurations with two FPDAs, Figure 62 FPDA provisioning for configurations with three FPDAs and two System Modules (sample 1), Figure 63 FPDA provisioning for configurations with three FPDAs and two System Modules (sample 2), Figure 64 FPDA provisioning for configurations with three FPDAs and one System Module (sample 3), and Figure 65 FPDA provisioning for configurations with four FPDAs and two System Modules show examples of FPDA provisioning based on the number of FPDAs. Circuit Breaker

Figure 60

DN09142359

24V DC

FPDA

48V DC

System Module

FPDA provisioning for configurations with one FPDA

Id:0900d80580a2f91d Confidential

61


Circuit Breaker

24V DC


FPDA 48V DC

Circuit Breaker

Figure 61

FPDA

48V DC

System Module

FPDA provisioning for configurations with two FPDAs

g

When FPDAs are installed in parallel, the DC output cables should be installed together at the FPDA closest to the System Module.

g

Two additional 4 AWG (25 mm2) cable lugs are required for each additional FPDA used in parallel. These lugs are not included in the delivery and must be sourced locally.

w

NOTICE: Risk of damage to equipment. When FPDAs are installed in parallel and a power failure occurs in a DC line, the input voltage to the System Module is likely to drop below the acceptable level. If an FPDA is overloaded with power, then the unit shuts itself down.

Figure 62

g

62

24V DC

FPDA provisioning for configurations with three FPDAs and two System Modules (sample 1)

In the example in Figure 62 FPDA provisioning for configurations with three FPDAs and two System Modules (sample 1), the power draw from the System Module to the single FPDA cannot exceed 2 kW.


DN09142359


Figure 63

Circuit Breaker

g

DN09142359

FPDA provisioning for configurations with three FPDAs and two System Modules (sample 2) 48V DC

24V DC

FPDA

Circuit Breaker

24V DC

Circuit Breaker

24V DC

Figure 64


System Module

FPDA

FPDA FPDA provisioning for configurations with three FPDAs and one System Module (sample 3)

In Figure 64 FPDA provisioning for configurations with three FPDAs and one System Module (sample 3), FPDA provisioning requires four pairs of double rubber boots (822862) for safety. The standard delivery for this configuration only includes three pairs of double boots. An extra pair must be ordered as a spare part for combining the DC cables at each System Module input terminal.


63


Figure 65


FPDA provisioning for configurations with four FPDAs and two System Modules

The FPDA is delivered with two sets of rubber boots: •

•

one set accommodates cable thickness of 35-50 mm2 (2 to 1/0 AWG) for 24 V DC input. Required cable thickness depends on the distance and voltage drop from the external 24 V DC power supply. the other set accommodates up to two 25 mm2 (4 AWG) cables per terminal for 48 V DC output to the System Module. These boots can be used for single or dual DC cables at each power terminal. Dual usage is required for pairing (chaining) cables when two FPDA modules are used in parallel as shown in Figure 66 Parallel FPDAs with paired (chained) DC cables and boots.

The FPDA(s) must be located close enough to the System Module so that the alarm cable reaches the appropriate connectors.

Figure 66

64

To System Module Parallel FPDAs with paired (chained) DC cables and boots


DN09142359



In FCIA and FCOA installation, the FPDA is installed directly to the rack without cable entries and plinth. Before you start •

•

Check that the 24 V DC supply system is switched off. In addition, make sure that its AC mains circuit breaker (and also the battery circuit breaker if the 24 V DC supply system is a battery back-up system) is switched off. When installing the FPDA in cabinets, detach the connection pins, support plates and cage nuts the same way as with the FPMA. See figure Installing FPMA inside FCOA steps 1 to 4 in Installing Flexi Power Module (FPMA) in FCOA.

w

NOTICE: Risk of damage to equipment. Incorrect cables and seals may not provide secured environmental protection. Use only tested IP65 class cables with seals provided by Nokia Siemens Networks.

w

NOTICE: Risk of damage to equipment. Connector seals or boots must be installed at all times, whether the site is active or not. Steps

1

Install the FPDA and (in cabinet installation) fix the module to the cabinet with screws.

2

Attach the cable entries using two screws (in stack, wall and pole installations).

2

3

2

Figure 67 3

DN09142359

Fixing cable entries

Make sure that the power switch on the front panel is in the stand-by position.


65


4


Connect the grounding cable to the plinth (in stack, wall and pole installations).

4 Figure 68

66

Connecting grounding cable to plinth


DN09142359


5

Remove the bolts and washers from the DC output terminals.

Figure 69 6


Connecting DC output cables to FPDA

Insert the rubber boots to the DC output cables. If the cable is 50 mm2 (1 AWG), cut the rubber boot to fit the cable. If two FPDAs are used in parallel, cut the sealed hole on the DC output boots.

7

Route the DC output cables through the cable entry (in stack, wall and pole installation). Use the top right entry hole for the V48N- cable and bottom right entry hole for the V48RTN+ cable.

8

DN09142359

Connect the V48N- cable to the minus terminal and V48RTN+ cable to the plus terminal in the FPDA module.


67


9


Tighten the bolts to 10.0 - 14.0 Nm (7.0 - 9.8 ft-lb) Nm.

10

Pull the rubber boots over the DC output terminals.

11

Connect the DC output cables to the System Module. Note that there is a risk of short circuit. Connect the power cable as instructed.

12

Remove one of the alarm connector seals on the front panel of the FPDA and connect the alarm cable. Make sure that you are inserting the cable connector as instructed in the figure.

To System Module Figure 70

Connecting alarm cable

13

Check that the power switch on the front panel of the FPDA is still in the stand-by position.

14

Make sure that the 24 V DC supply for the FPDA is de-energised and connect the DC input cables similarly as the DC output cables. Connect the minus wire to the minus terminal and the plus wire to the plus terminal. Note that the DC input cables are not included in the delivery. The length and thickness of the DC input cables must be defined based on the distance to the 24 V DC power source. The maximum thickness of a DC input cable that can be installed to the FPDA is 50 mm²/AWG 1/0.

15

Connect the AC mains power for the 24 V DC supply system.

16

Connect the 24 V DC supply (and the battery circuit breaker if the 24 V DC supply system is a battery back-up system). Make sure the LED is yellow.

68


DN09142359


17


Switch on the power by pushing the power switch on the front panel of the FPDA. Make sure the LED is green.

18

Make sure that the unused connectors are covered with seal caps. Make sure that the seal caps are inserted correctly.

19

DN09142359

Install the module front cover (in stack, wall and pole installation).


69

Installing Flexi Power Rectifier (FPRx)


9 Installing Flexi Power Rectifier (FPRx) 9.1

Principles for installing Flexi Power Rectifier (FPRx) in Flexi Multiradio BTS configurations The following locations for installing the Flexi Power Rectifier (FPRx) in Flexi Multiradio BTS configurations are recommended for ease of future expansion. The FPRx can be installed anywhere in a stack or cabinet provided that the 2 m (6.6 ft) alarm cable can be connected between the FPRx and System Module. For installation and cabling instructions, see Flexi Power Rectifier Product Documentation in Product Information Center. For alarm configuration instructions, see the following sections in the Cabling Flexi Multiradio BTS LTE and Installing Flexi Cabinet for Outdoor (FCOA) documents: • • • • • • •

Overview of connecting Flexi Power Rectifier (FPRA) alarms Connecting Flexi Power Rectifier (FPRA) alarm cable Connecting FPRA to System Module EAC connector Connecting FPRA to Flexi System External Alarm (FSEB) Overview of connecting Flexi Power Rectifier (FPRA) alarms for Flexi Cabinet Site Support Module (FCSA) Connecting 3 FPRA alarms and 4 FCSA alarms Connecting 6 FPRA alarms and 4 FCSA alarms

FCIA installations •

•

For installations in Flexi Cabinet for Indoor (FCIA) without batteries, the recommended location is at the top of the cabinet, near the cabinet roof. This helps reduce the amount of cabling routed along the sides of the cabinet. For FCIA installations with batteries, the recommended location is near the bottom of the cabinet, in the next available rack space above the batteries.

FCOA installations For installations in Flexi Cabinet for Outdoor (FCOA): • • •

•

70

If the System Module is in the top vertical rack, install the FPRx on the lower vertical rack, ensuring all cable entries come from the bottom of the module. If the System Module is in the horizontal rack, install the module in the top vertical rack. If the System Module and System Extension Module are installed in both vertical racks, install the module in either the top or bottom of the horizontal rack, depending on whether the top or bottom cable entry is used for the external power feed. For FCOA installations with Flexi Cabinet Site Support Module (FCSA), the FPRx is installed inside the FCSA. In that case, the AC interface support on the FCSA ceiling needs to be removed before installing the FPRx. For more information on this installation option, see Installing FPRx and site support module in the Installing Flexi Cabinet for Outdoor (FCOA) document.

Id:0900d80580a2f921 Confidential

DN09142359


Installing Flexi Power Rectifier (FPRx)

AC interface support

DN70473212

Figure 71

AC interface support

Floor installations • •

In outdoor installations, Flexi front and back covers (FMCA) must be used. The recommended location is the bottom of the stack. This allows for easier future expansion.

Note that when using front cover the air deflector plate has to be fixed to the front cover first. It is included in the FPRA delivery. Wall and pole installations • •

DN09142359

In outdoor installations, Flexi front and back covers (FMCA) must be used. The recommended location is either on the same plinth as the System Module or on an adjacent plinth.

Id:0900d80580a2f921 Confidential

71

Installing Flexi Power AC/DC sub-module 230V (FPAC)


10 Installing Flexi Power AC/DC sub-module 230V (FPAC) 10.1

Installing Flexi Power AC/DC sub-module (FPAC) on a wall Purpose These instructions show how to install Flexi Power AC/DC sub-module (FPAC) on a wall. No installation kit is required. Install the FPAC in proximity of a Flexi 2TX Remote Radio Head so that its 65 cm (25.6 in.) long DC cable can be routed through the RRH DC cable clamp and connected to the RRH screw terminal. Leave a minimum space of 1 cm (0.4 in.) between the FPAC and RRH. This includes the cable tie plate of the RRH. The installation distance is limited by the FPAC DC cable's physical path as well as the location of the RRH DC terminal location. Before you start

f

WARNING! Danger of lethal voltages. Switch off the AC power breaker before connecting the AC cable.

t

Always install Flexi Power AC/DC sub-module (FPAC) in a vertical position. The recommended installation location is on either side of the RRH. This allows optimal cooling for the RRH. Note also that the routing of the cables should not block the cooling fins. For more information on the FPAC sub-module, see Flexi Power AC/DC sub-module (FPAC) description in Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description.

72

Id:0900d80580a2ea38 Confidential

DN09142359



Steps 1

On the backside of the FPAC, undo the four screws holding the AC connector cover in place and open it.

Figure 72 2

Opening the AC connector cover

Loosen the screws on the AC cable clamp and thread your AC power cable through the IP boot. Loosen the two screws on the AC cable clamp to remove the boot.

DN09142359


73


74


Figure 73

Loosening the AC cable clamp screws

Figure 74

AC cable routing


DN09142359


3


Connect the AC power cable to the AC terminal.

Figure 75

Cabling completed

Tighten the M3 screws to 0.5 - 0.6 Nm (0.4 - 0.44 ft-lb.). 4

Close the AC connector cover. Tighten the M4 screws to 0.8 - 1.0 Nm (0.6 - 0.7 ft-lb.). Make sure that the AC connector cover’s IP seal is installed properly.

DN09142359


75


Figure 76 5

76


Closing the AC connector cover

Tighten the AC cable clamp screws.


DN09142359


6


Using the FPAC as a template, mark the screw hole locations on the wall.

Figure 77

Marking the fixing points

7

Drill the holes.

8

Install the FPAC and fix it with three screws. Note that the three pre-installed screws may need to be removed if they are not suitable for the wall material, for example wood or concrete.

9

Connect the RRH DC cabling. See Installing Flexi RRH 2TX on the pole in Installing Flexi Multiradio BTS LTE Modules for Stack, Wall, and Pole Configurations.

10

DN09142359

Turn the switch on the FPAC to the "On" position.


77


10.2

Installing Flexi Power AC/DC sub-module (FPAC) to a pole-mounted RRH Purpose These instructions show how to install Flexi Power AC/DC sub-module (FPAC) on a pole on the backside of a Flexi 2TX Remote Radio Head. You need a Flexi Pole Mounting Kit (FPKA) for this installation. Before you start

f


w

NOTICE: The weight of the RRH can damage the lower fixing bracket. Do not rest the RRH on the lower fixing bracket. Do not put force on the lower fixing bracket when lifting the RRH.

t

Always install Flexi Power AC/DC sub-module (FPAC) in a vertical position. Note also that the routing of the cables should not block the cooling fins. For more information on FPAC sub-module see Flexi Power AC/DC sub-module (FPAC) description in Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description.

78


DN09142359


Steps 1

Install Flexi Pole Mounting Kit (FPKA).

2

On the backside of the FPAC, undo the four screws holding the lid in place and open the AC connector cover.

Figure 78 3



DN09142359


79


80

Figure 79


Figure 80

AC cable routing


DN09142359


4


Figure 81

Cabling completed


Close the AC connector cover. Tighten the M4 screws to 0.8 - 1.0 Nm (0.6 - 0.7 ft-lb.). Make sure that the AC connector cover’s IP seal is installed properly.

DN09142359


81


Figure 82


6


7

Fit the FPAC on the RRH mounting brackets and fix with three pre-installed screws. Flip the RRH over so that it is resting carefully on the solar shield. Use the fixing points shown in the below figure. The FPAC can be installed on the left or right side of the RRH mounting kit brackets. Each side has two sets mounting holes for the FPAC, depending on the RRH mounting dimensions.

82


DN09142359


Figure 83

DN09142359

Fixing points


83


Figure 84 8

FPAC installed using the right-hand side fixing points

Install Flexi 2TX Remote Radio Head on the FPKA. See Installing Flexi RRH 2TX on the pole in Installing Flexi Multiradio BTS LTE Modules for Stack, Wall, and Pole Configurations.

9


10

84

Turn the switch on the FPAC to the "On" position.


DN09142359


Installing Flexi Power AC/DC sub-module (FPAD)

11 Installing Flexi Power AC/DC sub-module (FPAD) 11.1

Installing Flexi Power AC/DC sub-module (FPAD) on a wall Purpose These instructions show how to install Flexi Power AC/DC sub-module (FPAD) on a wall. No installation kit is required. Install the FPAD in proximity of a Flexi 2TX Remote Radio Head so that its 65 cm (25.6 in.) long DC cable can be routed through the RRH DC cable clamp and connected to the RRH screw terminal. Leave a minimum space of 1 cm (0.4 in.) between the FPAD and RRH. This includes the cable tie plate of the RRH. The installation distance is limited by the FPAD DC cable's physical path as well as the location of the RRH DC terminal location. Before you start

f


t

Always install Flexi Power AC/DC sub-module (FPAD) in a vertical position. The recommended installation location is on either side of the RRH. This allows optimal cooling for the RRH. Note also that the routing of the cables should not block the cooling fins. For more information on the FPAD sub-module, see Flexi Power AC/DC sub-module (FPAD) description in Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description.

DN09142359

Id:0900d80580a2abcf Confidential

85



Steps 1

On the backside of the FPAD, undo the four screws holding the AC connector cover in place and open it.

Figure 85 2



Figure 86

86



DN09142359


Figure 87

DN09142359


AC cable routing


87


3



Figure 88

Wires connected


Close the AC connector cover. Tighten the M4 screws to 0.8 - 1.0 Nm (0.6 - 0.7 ft-lb.). Make sure that the IP seal of the AC connector cover is installed properly.

88


DN09142359


Figure 89 5



Figure 90

DN09142359


AC cable clamp screws fixed


89


6


Using the FPAD as a template, mark the screw hole locations on the wall.

Figure 91

Marking the fixing points

7

Drill the holes.

8

Install the FPAD and fix it with three screws. Note that the three pre-installed screws may need to be removed if they are not suitable for the wall material, for example wood or concrete.

9


10

90

Turn the switch on the FPAD to the "On" position.


DN09142359


11.2

Installing Flexi Power AC/DC sub-module (FPAD) to a pole-mounted RRH Purpose These instructions show how to install Flexi Power AC/DC sub-module (FPAD) on a pole on the backside of a Flexi 2TX Remote Radio Head. You need a Flexi Pole Mounting Kit (FPKA) for this installation. Before you start

f


w

NOTICE: The weight of the RRH can damage the lower fixing bracket. Do not rest the RRH on the lower fixing bracket. Do not put force on the lower fixing bracket when lifting the RRH.

t

Always install Flexi Power AC/DC sub-module (FPAD) in a vertical position. Note also that the routing of the cables should not block the cooling fins. For more information on the FPAD sub-module see Flexi Power AC/DC sub-module (FPAD) description in Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description.

DN09142359

Id:0900d80580a2abd1 Confidential

91


Steps 1

Install Flexi Pole Mounting Kit (FPKA).

2

On the backside of the FPAD, undo the four screws holding the lid in place and open the AC connector cover.

Figure 92 3



92


DN09142359


DN09142359

Figure 93


Figure 94

AC cable routing


93


4


Figure 95

Wires connected

Tighten the M3 screws to 0.5 - 0.6 Nm (0.4 - 0.44 ft-lb.) . 5

Close the AC connector cover. Tighten the M4 screws to 0.8 - 1.0 Nm (0.6 - 0.7 ft-lb.). Make sure that the IP seal of the AC connector cover is installed properly.

94


DN09142359


Figure 96 6


Figure 97 7


AC cable clamp screws fixed

Fit the FPAD on the RRH mounting brackets and fix with three pre-installed screws. Flip the RRH over so that it is resting carefully on the solar shield. Use the fixing points shown in Figure 98 Fixing points. The FPAD can be installed on the left or right side of the RRH mounting kit brackets. Each side has two sets mounting holes for the FPAD, depending on the RRH mounting dimensions.

DN09142359


95


Figure 98

96

Fixing points


DN09142359


Figure 99 8

FPAD installed using the right-hand side fixing points

Install Flexi 2TX Remote Radio Head on the FPKA. See Installing Flexi RRH 2TX on the pole in Installing Flexi Multiradio BTS LTE Modules for Stack, Wall, and Pole Configurations.

9


DN09142359


97


10

98

Turn the switch on the FPAD to the "On" position.


DN09142359


Installing Flexi Power Distribution and Fuses Outdoor (FPFC)

12 Installing Flexi Power Distribution and Fuses Outdoor (FPFC) Purpose The following installation options are available for Flexi Power Distribution and Fuses Outdoor (FPFC): • • • •

Inside 2U casing (EMTA) Inside 3U casing (EMHA/FMSC) Inside a 19-inch rack or cabinet Chained with another FPFC

EMTA/EMHA/FMSC casings are not delivered with FPFC and must be ordered separately. Note also that if FPFC is installed in a tower, FSEC is needed to protect the DC power supply. FPFC is shown in Figure 100 Flexi Power Distribution and Fuses Outdoor (FPFC). For more information on the FPFC unit and cable properties see Flexi Power Distribution and Fuses Outdoor (FPFC) Description. FPFC delivery contents are listed in section Contents of the Flexi Power Distribution and Fuses Outdoor (FPFC) delivery.

FPFC

EAC connector

Input connector IP boot

Input connector

On/Off Bar

Output connector IP boot

Figure 100 Flexi Power Distribution and Fuses Outdoor (FPFC) See Figure 101 FPFC installation example for an example FPFC installation.

DN09142359


99



FODA FPFC

RFM

Outdoor FODA System Module System Module

Figure 101 FPFC installation example

12.1

Installing FPFC inside a casing Steps

1

Insert the FPFC inside a 2U or 3U casing. Push the FPFC into the casing and fix it to the casing. If FPFC is installed in a 2U casing, the maximum cable thickness is 5 x 21 mm + 2 x 11 mm outer diameter cable or 6 x 16 mm outer diameter cable. For 2 x 35 mm2 (AWG 2) conductor + 16 mm2 (AWG 6) shielded cable the outer jacket should be stripped.

2

Connect the grounding cable between the FPFC front panel and the grounding point. Connect the cable between the FPFC front panel fixing point and the grounding point, for example the plinth. See Figure 102 FPFC grounding points for the location of the FPFC front panel fixing points. There is one point for M8 size screw and two for M5 sized screws.

100


DN09142359



M5 Grounding poits

Figure 102 FPFC grounding points 3

Connect the EAC cable to FPFC. See Figure 103 EAC cable routing for an example of the EAC cable routing. The cable connector sealing can be detached to connect the EAC connector.

EAC cable

Figure 103 EAC cable routing

f

CAUTION! Risk of damage to equipment Connector seals or boots must be installed at all times, whether the site is active or not.

4

Prepare the input cabling. See Table 3 Input cable application cases for details.

DN09142359


101


Input use case From AC/DC


Wire crosssection

Outer Diameter

50 mm2 (AWG 1) 13.5 mm

(short distance < 4 m)

Cascading or AC/DC

Single wire cable (cables separate for plus and minus)

Conductor 35 mm2 (AWG 2)

28 mm

(long distance > 4 m)

Shield 16 (AWG 6)

Cascading

35 mm2 (AWG 2) 11 mm

mm2

(short distance < 4 m) Table 3

Note

Shielded cable Cable shield must be stripped and cold shrinkable tube must be used Single wire cable

Input cable application cases

Make sure all the cables are prepared. Note that if the cable diameter is >25 mm (1 in.), it is too hard to route the cable with cable entries and front cover in place. If the cable diameter is >25 mm (1 in.), follow these steps to prepare the cable: 1. Strip off the outer jacket of the cable as shown in Figure 104 Cable outer jacket stripping (input from right-hand side). Note that these measurements are the maximum values for a case where the cabling is routed by the right-hand side of the FPFC. 400 mm (15.7 in.) 17 mm (0.7 in.)

Shielding Length 420 mm (16.5 in.)

Figure 104 Cable outer jacket stripping (input from right-hand side) If the input cabling is routed by the left-hand side of the FPFC, the measurements are the following:

102


DN09142359



300 mm (11.8 in.) 17 mm (0.7 in.)


Figure 105 Cable outer jacket stripping (input from left-hand side) 2. If the peeled sections are left outside the casing, a cold shrink tube (CS73327.26) must be used to provide UV protection. See Figure 106 Three-fingered cold shrink tube installed for example usage.

Cable Cold shrinking tubing

Figure 106 Three-fingered cold shrink tube installed 5

Insert the input cables to the IP boots. Observe the following when routing cables through the IP boots: • •

DN09142359

Cut the center of the boot according to the cable diameter so that the reinforcement ring is intact, and make sure that the cable cross ports are not damaged. If the cable diameter is > 15mm (0.6 in.), cut the boot as shown in Figure 107 Cable diameters for input IP boot.


103



Cable diameter 16-28 mm (0.6-1.1 in.) Cable diameter 5-15 mm (0.2-0.6 in.) Figure 107 Cable diameters for input IP boot • •

Route the cables carefully through the boot. Make sure the cable size is correct for the boot cable diameter. The copper shielding wire should also be wrapped up with single cold shrink tubing as shown. Type: CS930345.

Make sure that the tube ends are properly sealed. 6

Strip the necessary conductor wires of the input cables. See Figure 108 Cable diameter >25 mm (1 in.) (input from right-hand side), Figure 109 Cable diameter >25 mm (1 in.) (input from left-hand side) and Figure 110 Cable diameter <25 mm (1 in.) for details. The recommended length for the exposed wire is 17 mm (0.67 in.). 400 mm (15.7 in.) 17 mm (0.7 in.)


Figure 108 Cable diameter >25 mm (1 in.) (input from right-hand side)

104


DN09142359



300 mm (11.8 in.) 17 mm (0.7 in.)


Figure 109 Cable diameter >25 mm (1 in.) (input from left-hand side) 40 mm (1.6 in.) 17 mm (0.7 in.)

60 mm (2.4 in.) Shielding Length

Figure 110 Cable diameter <25 mm (1 in.)

g 7

Make sure that the cable insulation is not damaged. The diffuse copper wire should be bushed so that it is easy to connect.

Connect the 48V DC input cables. Insert the cables to the input and output connectors as required. Each input connector can support two power supplies. 1. Insert the cables to the input connector. The cable size support for input cable is 2.5 - 50 mm2 (AWG 14 - AWG 1), and GND cable size can be 2.5 - 50 mm2 (AWG 14 AWG 1).

DN09142359


105



max. 50 mm2

Figure 111 Input cable connectors 2. Fix the connection screws and attach the IP boot to the connector. Use a Torx 20 screwdriver.

Figure 112 Fixing the input cable connection

g

Make sure the IP boots are undamaged. Make sure that the cables are properly installed to the connectors. The torque for the connection fixing screw is 4 Nm (3 ft-lb.).

106


DN09142359



Figure 113 Typical input cabling from right-hand side for single FPFC It is also possible to route the cables from the left-hand side. If required, input power for the FPFC can be fed from both sides with two DC cables. These cables must have exactly the same dimension, type and length so that power is distributed from them equally. This can be used, for example, in following cases: •

•

•

The original plan was to use only half of the outputs and input cable dimensioning was done according to this, and if all outputs are used, a second same size and length cable can be installed instead of replacing the existing cable with a thicker one If distance, power demand and loss requirements show that input cable must be thicker than the maximum supported size for the input connector, cabling from both sides can be a solution In some cases two smaller cables can be more cost effective when compared with one thicker cable because of market situation.

See Figure 114 FPFC input cabling from both sides for example cabling.

FPFC

GND

GND

GND

Figure 114 FPFC input cabling from both sides 8

Prepare the output cabling. See Table 4 Output cable application casesfor details. Output use case MW equipment IDU/ODU/FOC

Wire crosssection 2.5 mm2 (AWG 14)

Outer Diameter 6.5 - 11 mm

Note Single wire cable

(short distance < 4 m) Table 4

DN09142359

Output cable application cases


107


Output use case MW equipment IDU/ODU/FOC


Wire crosssection

Outer Diameter

Note

2.5 mm2 (AWG 14)

6.5 - 11 mm

Shielded cable

3.3 mm2 (AWG 12)

8.3 mm

Single wire cable


15 mm

Shielded cable

(long distance > 4 m) RF Module (short distance < 4 m) RF Module (long distance > 4 m) RRH

Shield 16 mm2 (AWG 6) 6 mm2 (AWG 10) 11 mm

(short distance < 4 m) RRH (long distance > 4 m)

Conductor 6-16 mm2 (AWG 10 AWG 6)

7-21 mm

Single wire cable Shielded cable

Shield 2.5 - 16 mm2 (AWG 14 AWG 6) System Module

35 mm2 (AWG 2) 11 mm

Single wire cable

Cascading

35 mm2 (AWG 2) 11 mm

Single wire cable

(short distance < 4 m) Cascading (long distance > 4 m)

Table 4


28 mm

Shield 16 mm2 (AWG 6)

Shielded cable Cable shield must be stripped and cold shrinkable tube must be used

Output cable application cases (Cont.)

Make sure all cables are prepared. Note that if the cable diameter is >25 mm (1 in.), it is too hard to route the cable with cable entries and front cover in place. If the cable diameter is >25 mm (1 in.), follow these steps to prepare the cable: 1. Strip off the outer jacket of the cable as shown in Figure 115 Cable outer jacket stripping (output from right-hand side). Note that these measurements are the maximum values for a case where the cabling is routed by the right-hand side of the FPFC.

108


DN09142359



400 mm (15.7 in.) 17 mm (0.7 in.)


Figure 115 Cable outer jacket stripping (output from right-hand side) If the cabling is routed by the left-hand side of the FPFC, the measurements are the following: 300 mm (11.8 in.) 17 mm (0.7 in.)


Figure 116 Cable outer jacket stripping (output from left-hand side) 2. If the peeled sections are left outside the casing, a cold shrink tube (CS73327.26) must be used to provide UV protection. See Figure 117 Three-fingered cold shrink tube installed for example usage.

Cable Cold shrinking tubing

Figure 117 Three-fingered cold shrink tube installed 9

Insert the output cables to the IP boots. Observe the following when routing cables through the IP boots: • •

DN09142359

Cut the center of the boot according to the cable diameter so that the reinforcement ring is intact and make sure that the cable cross ports are not damaged. If the cable diameter is > 15mm (0.6 in.), cut the boot as shown in Figure 118 IP boot cutting.


109



Cable diameter 15-28 mm (0.6-1.1 in.)

Cable diameter 5-15 mm (0.2-0.6 in.)

Figure 118 IP boot cutting • •

Route the cables carefully through the boot. Make sure the cable size is correct for the boot cable diameter. The copper shielding wire should also be wrapped up with single cold shrink tubing as shown. Type: CS930345.

Make sure that the tube ends are properly sealed. 10

Strip the necessary conductor wires of the output cables. See Figure 119 Cable diameter >25 mm (1 in.)(output from right-hand side), Figure 120 Cable diameter >25 mm (1 in.) (output from left-hand side) and Figure 121 Cable diameter <25 mm (1 in.) for details. The recommended length for the exposed wire is 17 mm (0.67 in.). 400 mm (15.7 in.) 17 mm (0.7 in.)


Figure 119 Cable diameter >25 mm (1 in.)(output from right-hand side) 300 mm (11.8 in.) 17 mm (0.7 in.)


Figure 120 Cable diameter >25 mm (1 in.) (output from left-hand side)

110


DN09142359



40 mm (1.6 in.) 17 mm (0.7 in.)

60 mm (2.4 in.) Shielding Length

Figure 121 Cable diameter <25 mm (1 in.)

g 11

Make sure that the cable insulation is not damaged. The diffuse copper wire should be bushed so that it is easy to connect.

Connect the 48V DC output cables. Insert the cables to the output connectors as required. 1. Insert the cables to the output connectors. The cable size support for output cable size is 2.5 - 35 mm2 (AWG 14 - AWG 2) and GND cable size can be 2.5 - 20 mm2 (AWG 14 - AWG 5).

max. 20 mm 2

max. 50 mm 2

Figure 122 Output cable connectors and GND, max values 2. Fix the connection screws using a Torx 20 screwdriver and attach the IP boots to the connectors.

DN09142359


111



Figure 123 Fixing the output cable connection

g

Make sure the IP boots are undamaged. Make sure that the cables are properly installed to the connectors. The torque for the connection fixing screw is 4 Nm (3 ft-lb.).

12

Attach the cable entries on both sides of the module. Use four M5 x 10 screws for attaching the cable entries.

Figure 124 Cable routing in 2U casing with left-hand side input cabling 13

Route the cables through the cable entries.

14

Check the position of the On/Off bar(s). The bar(s) should be in ‘On’ position.

112


DN09142359



ON

Figure 125 On/Off bar ‘On’ position 15

Check the position of output current knob(s). The knob(s) can be adjusted with a flathead screwdriver. Note that only right-hand side channels’ 3-6 output current can be adjusted. The available current values are 4A, 15A and 30A.

Figure 126 Adjusting the output current knob

DN09142359

16

Fix the cable clamps on cable entries, if necessary.

17

Fix the cables with cable clamps or cable ties.

18

Install the front cover.


113


12.2


Installing FPFC in a chained configuration Steps

1

f

Connect the EAC cable. CAUTION! Risk of damage to equipment Connector seals or boots must be installed at all times, whether the site is active or not.

2

Route and prepare the required cabling based on site requirements. See 12.1 Installing FPFC inside a casing above for information on preparing the cables.

3

Connect the input cable. Connect the main FPFC input cable as in 12.1 Installing FPFC inside a casing. Connect the slave FPFC’s input connector with the main FPFC as shown in Figure 127 Two FPFCs chained. Make sure the polarity matches the chained unit.

Slave FPFC

GND

Chaining cables

GND

Master FPFC

GND

GND

GND

Figure 127 Two FPFCs chained 4

Check the position of the On/Off bar(s). It should be in “On” position.

5

Check the position of output current knob(s). The knob(s) can be adjusted with a flathead screwdriver. Note that only channels’ 3-6 output current can be adjusted. See Figure 126 Adjusting the output current knob.

114

6

Fix the cable clamps on cable entries, if necessary.

7

Fix the cables with cable clamps or cable ties.


DN09142359


8

DN09142359


Install the front cover.


115

Installing Flexi System External OVP (FSEC)


13 Installing Flexi System External OVP (FSEC) FSEC is not relevant for TD-LTE.

Purpose The Flexi System External OVP (FSEC) assembly protects the Flexi BTS modules against surge pulses in power feeding lines. There are five versions of the FSEC, which are separated from each other by the first two digits of the factory code: • • • • •

6Yxxxxxxxxx E4xxxxxxxxx S1xxxxxxxxx M2xxxxxxxxx V5xxxxxxxxx

See the appropriate wiring instructions below according to which version you have. The maximum DC cable thickness for the FSEC is 35 mm2. There are two mounting kits for the FSEC: • •

Flexi Mounting Auxiliary Brackets (FMAA) for stack installations Flexi Pole Installation Kit (FPIA) for pole and wall installations

See the following figure for an installation example with three RF Modules.

System wiring 1st RF Module FSEC From RF1, RF2 and RF3 connectors

2nd RF Module FSEC

System Module FSEC FSEC

3rd RF Module FSEC

FSEC

DN70272424

Figure 128 Installation example with three RF Modules If using Flexi Mounting Auxiliary Brackets (FMAA), see Figure 129 FMAA with two FSECs for the installation position of the FSEC on the module casing.

116

Id:0900d80580a2ad07 Confidential

DN09142359



FMAA

FMAA FSEC

FSEC

FSEC FSEC

FMAA

DN70456974

Figure 129 FMAA with two FSECs Note that if only one FSEC is required, it can be installed in any of the four positions shown in Figure 129 FMAA with two FSECs.

FMAA

FMAA FSEB

FSEB FMAA FSEC FSEC

DN70456959

Figure 130 FMAA with FSEB and FSEC The FSEC can also be installed on the FCOA roof. The fixing points on the cabinet roof are illustrated in Figure 131 FSEC fixing points on the FCOA roof.

DN09142359


117



1.

2.

3.

Figure 131 FSEC fixing points on the FCOA roof Steps 1

Open the lid of the FSEC box.

1

DN70232273

Figure 132 Opening FSEC If you have version S1/M2/V5xxxxxxxxx, remove the protector board from inside the FSEC at this point to make connecting the wires easier.

118


DN09142359



Figure 133 Removing protector board 2

Install the box. The maximum installation distance of the FSEC is 1.5 m (59.1 in) from the RF Module.

DN70458321

Figure 134 Installing FSEC

DN09142359


119



In pole installations, use the fixing kit: a) Thread the straining straps to the installation plate. b) Tighten the straining straps around the pole.

2b 2a

DN70276768

Figure 135 Installing FPIA 3

Connect the grounding cable (GND). Route the grounding cable from the bottom right corner of the FSEC box to the grounding point on the plinth.

120


DN09142359



3

to plinth DN70276771

Figure 136 Connecting grounding cable

DN09142359


121


Cut the DC cable included in the delivery close to the connector, strip it as necessary to reveal the black and blue wires and connect the wires.. 6Yxxxxxxxxx

E4xxxxxxxxx Vrtn

+

+

PE

-

-

N.O. N.C. COM

4


Vrtn Vrtn Vin

PE

4

Vin

PE PE PE Vin

4

to RF/System Module

to RF/System Module

S1/M2/V5xxxxxxxxx

Vrtn

Vin

PE

PE

Vin

Vrtn

4

to RF/System Module

DN70276826

Figure 137 Connecting DC cable to FSEC from RF or System Module 5

Connect the other end of the DC cable to the RF Module. Make sure that the seal cap is in place.

122


DN09142359



Figure 138 Connecting DC cable to RF Module 6

t

Connect the DC feeder cable to the FSEC box. For DC feeder cable details, see Feederless site and Distributed site solution requirements in the Flexi Multiradio BTS LTE Installation Site Requirements document. The colours of the cables may vary depending on the country or cable type. The shielding of the feeder cable must be connected to the PE terminal at both ends.

6Yxxxxxxxxx

+

+

PE

-

-

PE

121114 1211 14

6

DN70276783

Figure 139 Connecting DC feeder cable to FSEC (6Yxxxxxxxxx)

DN09142359


123



S1/M2/V5xxxxxxxxx (48V system floating or 48V system positive grounding)

E4xxxxxxxxx(48V system floating or 48V system positive grounding)

Vrtn

Vin

Vin

N.O. N.C. COM

Vrtn

Vrtn Vrtn Vin

+

+

-

PE

PE PE

-

Vin

Vin

Vrtn

PE

Vin

PE

-

+

-

Vrtn

+

6

6

DN70607894

Figure 140 48V system floating or 48V system positive grounding S1/M2/V5xxxxxxxxx (+24V/48V system, negative grounding)

Vin

Vin Vrtn

Vrtn

N.O. N.C. COM

E4xxxxxxxxx(+24V/48V system, negative grounding)

Vrtn Vrtn Vin

PE PE PE Vin Vin

Vrtn

-

+

PE

PE

Vin

Vrtn

+ -

6

6

DN70607901

Figure 141 +24V/48V system, negative grounding

124


DN09142359


7


Route the DC cable to the System Module. RF1 RF2 RF3 EXT

Figure 142 Connecting DC cable to System Module For detailed description on FPFD cabling, see Connecting Flexi Multiradio 10 BTS Power Distribution Sub-Module (FPFD) cabling in theCabling Flexi Multiradio 10 BTS Outdoor document.

DN09142359

8

If you have version S1/M2/V5xxxxxxxxx, reinstall the protector board.

9

Install the module front covers.


125


10


If used, connect the alarm cable (not included in the FSEC delivery).

6Yxxxxxxxxx

-10

For normal open(N.O.) connect + wire to N.O. and -wire to COM. For Normal Closed(N.C.) connect + wire to N.C. and -wire to COM. The shielding must be connected to PE.

Vrtn

Vin

S1/M2/V5xxxxxxxxx N.C. COM N.O.

N.O. N.C. COM

Vin

Vrtn

PE 12 11 14 12 11 14

E4xxxxxxxxx

Vrtn

--

PE

PE

PE

Vin

DN70280907

Figure 143 Connecting alarm cable 11

Repeat steps 4-7 for connecting the FSEC to the System Module.

12

Check the FSEC connections and close the box. Tighten the lid screws to 2.5 Nm (1.8 ft-lb.).

126


DN09142359



12

DN70276853

Figure 144 Closing FSEC

DN09142359


127

Installing Flexi System External OVP (FSES)


14 Installing Flexi System External OVP (FSES) 14.1

Installing Flexi System External OVP (FSES) onto a 3U casing These instructions describe how to install Flexi System External OVP (FSES) onto a 3U module casing (082795A.204 or newer). FSES interfaces are shown in the following figure.

Alarm interface DC output/input

DC output/input Grounding

Figure 145 FSES interfaces

g

Do not open the FSES. If opened, the warranty is void.

1

Make sure the 3U cable entries have been installed.

2

Install the FSES onto the module casing as shown in the below figure and fix with two screws. The distance between the RF Module and the FSES is limited by the length of the output power cable (180 cm, 5.9 ft.) and its physical path.

128

Id:0900d805809c81e8 Confidential

DN09142359



Figure 146 Installing FSES on casing Tighten the screws to 2.0 - 2.5 Nm (1.5 - 1.8 ft-lb.). Alternatively, you can connect the cabling first and then install the FSES ready-cabled.

DN09142359


129


3


Connect the pre-installed grounding cable (994815) to the plinth.

Radio Module Figure 147 Connecting FSES grounding cable to plinth

130


DN09142359


4


Remove the FSES IP boot.

Figure 148 Removing FSES IP boot 5

Strip the DC power cable and wrap tape around the exposed wires in order not to break the IP boot. a

Strip the DC cable about 10 cm (4 in) and wrap tape around GND mesh and cable sheath neck.

Figure 149 Wrapping tape around shielded DC cable b

DN09142359

Wrap an extra tape around the exposed wires in order not to break the IP boot


131



Figure 150 Wrapping an extra tape around DC cable c

Insert the taped end of the DC feeder cable into the IP boot.

Figure 151 Inserting DC power cable to IP boot When using a thick cable, the narrow end of the IP boot can be removed using scissors. Cut in one go so that you get a clean cut surface. See Figure 152 Removing narrow end of IP boot for details. Note that you can insert only one DC cable with a diameter of maximum 25 mm to the IP boot. Minimum cable diameter is 6 mm.

w

132

NOTICE: The IP boot edge must be smooth. No crack in the edge is allowed, as it breaks boot IP protection.


DN09142359



Cable diameter 20.1 - 25.0 mm cut with scissors in one go Cable diameter 15.1 - 20.0 mm cut with scissors in one go Cable diameter 10.1 - 15.0 mm cut with scissors in one go Cable diameter 6.0 - 10.0 mm (no cutting need)

Figure 152 Removing narrow end of IP boot d

g

DN09142359

Remove the extra tape from DC cable. Keep the tape around the GND mesh and cable sheath neck to protect IP boot from sharp edges.


133



Figure 153 Properly secured shielded DC cable (left) and non-shielded DC cable (right) For DC feeder cable details, see Feederless site and Distributed site solution requirements in the Flexi Multiradio BTS LTE Installation Site Requirements document. 6

Connect the wires to the screw terminal. Tighten to 5.0 Nm (3.7 ft-lb.).

+

GND

-

Figure 154 Connecting DC feeder cable wires Pay attention to the markings (V48N (-), V48RTN (+) and GND) on the FSES lid to ensure correct polarity. If you have a shielded DC cable, connect the shielding to the terminal marked with GND. Note that the FSES grounding cable has to be connected to the plinth. 7

Fix the IP boot in place and fix the screw. Tighten to max. 2.0 Nm (1.5 ft-lb.). Bend the IP boot to the side to make it easier to fix the screw.

134


DN09142359



Figure 155 Fixing IP boot screw 8

Fix the DC feeder cable to the cable entry with a cable tie. To ensure the FSES DC feeder cable proper strain relief, also fix the DC feeder cable firmly to the surrounding structure of the Flexi module, as close as possible to the input connection.

Figure 156 Fixing DC feeder cable to cable entry

DN09142359


135


9


Depending on your cable routing, fix the DC power cable and grounding cable to the cable entry with a cable tie. It is recommended that the DC power cable is routed down.

Figure 157 Fixing DC power cable with cable tie 10

If applicable, connect the alarm cable following the steps below. Alarm output is Normally Open type. An alarm cable is not included in the FSES delivery. Use an alarm cable that meets the following requirements: • • • •

•

Minimum wire size 0.5 mm2 (20 AWG) Maximum wire size 2.5 mm2 (14 AWG) Round cable outer jacket diameter must be 8.3 +/- 0.5 mm For the maximum length, see the maximum distance between the System Module and RF Module in Feederless site and Distributed site solution requirements in the Flexi Multiradio BTS LTE Installation Site Requirements document Maximum current 1.0 mA

a

Remove the alarm port IP boot.

Figure 158 Removing alarm port IP boot

136


DN09142359


b


Remove the IP plug from the IP boot.

Figure 159 Removing IP plug c

Insert the alarm cable to the IP boot.

Figure 160 Inserting alarm cable to IP boot

DN09142359


137


d


Connect the wires to the N.O. and Common terminals.

Figure 161 Connecting alarm cable wires e

Fix the IP boot in place.

Figure 162 Fixing alarm cable IP boot f

138

Connect the other end of the alarm cable either to the EAC port on the System Module front panel or to Flexi System External Alarm (FSEB).


DN09142359


11


Connect the ready-installed DC cable as required by your configuration: • •

System Module front panel: RF1/2/3 output port. RF Module front panel: DC in port.

Make sure that the IP boot is installed properly on the System Module or RF Module front panel. 12

If applicable, install another FSES on top of the first one. Repeat steps 3 to 13. Fix with four screws. The maximum number of FSES's in a stack is two.

Figure 163 Two FSES’s stacked

DN09142359


139


14.2

Installing Flexi System External OVP (FSES) on a Flexi cabinet rooftop These instructions describe how to install Flexi System External OVP (FSES) on the roof of Flexi Cabinet for Indoor (FCIA) or Flexi Cabinet for Outdoor (FCOA). Use the fixing points on the cabinet roof. See the figures below for suggested positions, however, if the rooftop is populated with other auxiliary equipment, use any available slot for installing the FSES. Always make sure that the FSES can be fixed firmly and cables tied appropriately.

FSES

Figure 164 Example of FCIA rooftop installation

140

Id:0900d805809c821c Confidential

DN09142359


FSEB

FSES

FSEC

Figure 165 Example of FCOA rooftop installation (with FSEB and FSEC)

g

DN09142359


1

Using any small tool, knock off the installation hooks on the bottom of the FSES with a light sideways blow. Alternatively, twist the hooks off with pliers.

2

Fix the FSES on the FCIA/FCOA rooftop with two screws on one side.

3

Connect the cabling as instructed in Installing Flexi System External OVP (FSES) onto a 3U casing.

g

If the ready-installed DC cable does not reach the System Module installed in one of the bottommost slots in the FCIA cabinet, swap the System Module and RF Module around so that the System Module moves higher in the configuration.

Id:0900d805809c821c Confidential

141


14.3

Installing Flexi System External OVP (FSES) onto Flexi Pole Installation Kit (FPIA) These instructions describe how to install Flexi System External OVP (FSES) on a pole using Flexi Pole Installation Kit (FPIA) (version 471767.202 or newer).

g


1

Install Flexi Pole Installation Kit (FPIA) as instructed in Installing Flexi Pole Installation Kit (FPIA).

2

Fix the FSES on the FPIA with four screws.

Figure 166 FSES installed on FPIA

142

Id:0900d805809a2b0b Confidential

DN09142359


3

If you are installing more than one FSES on the FPIA, install the additional FSES's as shown in the figures below.

Figure 167 Two FSES’s on FPIA

DN09142359


143


Figure 168 Four FSES’s on FPIA 4

144

Connect the cabling as instructed in Installing Flexi System External OVP (FSES) onto a 3U casing.


DN09142359


Installing Flexi Fiber Optical Distribution unit (FODA)

15 Installing Flexi Fiber Optical Distribution unit (FODA) 15.1

Installing Flexi Fiber Optical Distribution unit (FODA) in a stack Follow these instructions to install FODA unit in a stack or rack. Purpose The following installation options are available for Flexi Fiber Optical Distribution unit (FODA): • • • • •

inside 3U casing (EMHA) with FPFC on top of a casing inside a 19” rack or cabinet on a pole on a wall.

Cable gland

OPT1-3

OPT4-5 OPT6

OPT7 OPT8-9

OPT10-12

Cable gland optional Figure 169 Flexi Fiber Optical Distribution unit (FODA) Installation examples:

DN09142359

Id:0900d805809a4b9a Confidential

145



FODA FPFC

RFM

Outdoor FODA System Module System Module

Figure 170 Outdoor installation example

146


DN09142359



Tower top

GSM/LTE

ANT 1 Tx/Rx ANT 1 Rx Out

ANT 2 Rx ANT 3 Tx/Rx

EAC

ANT 4 Rx ANT 6 Rx PWR IN

ANT 5 Rx Out

ANT 5 Tx/Rx

ANT 3 Rx Out


ANT 4 Rx ANT 5 Tx/Rx

EAC

ANT 5 Rx Out

ANT 6 Rx PWR IN

RF jumper Fiber DC

OPT 2 OPT 3 OPT 1


ANT 2 Rx

OPT 2 OPT 3 OPT 1

GSM/ WCDMA

GSM/WCDMA

FODA FPFC

GSM/LTE

FPFC + FODA v2 Max. 24 x SM FIBER Max. 12 x DC

Ground level FODA

LTE FSME Power cabinet GSM ESMB FPA OPT1 OPT2

PWR

PWR

OPT3 OPT4

PWR

LMP

PWR

GSM ESMB

WCDMA FSME Sync-Out Sync-In

EAC

Q1

PWR

FPA OPT1 OPT2

PWR

PWR

OPT3 OPT4

PWR

LMP

PWR

Sync-Out Sync-In

EAC

Q1

PWR

Figure 171 Installation example with FODA Steps 1

Open the lid of the FODA unit. Open the lid of the FODA unit by removing the 14 M5 screws (TORX T25). See the figure below, step 1.

DN09142359


147



3

1

2 3 Figure 172 Opening the lid of FODA 2

Remove the connector seals from the relevant optical cable connectors in the FODA unit. See Figure 172 Opening the lid of FODA, step 2. Store the seals for later use. You can store these inside FODA.

3

Change the location of the cable gland from the side to the front of the FODA unit. See Figure 172 Opening the lid of FODA, step 3. Changing the location of the cable gland is only required for stack and rack installations.

4

Route the input fiber cables via the cable gland. Detach first the nut from the cable gland and route the cables through the nut one by one. Then route the cables through the cable gland. See the figure below.

148


DN09142359



2

1

Figure 173 Routing cables through the cable gland 5

Attach the input fiber cables to the relevant connectors inside FODA. See the figure below for example routing. The cables are numbered, so make sure to attach the cables to appropriate connectors.

1

12 1 2 3

4 5

6

7

8 9

10 11

12

Figure 174 Routing fibers inside FODA 6

Tighten the cable gland. See the figure below. The torque for the cable gland is 0.7 Nm (0.5 ft-lb). Make sure the cable IP sleeve is installed so that it goes through the gland as in the figure below.

DN09142359


149



Cable IP sleeve

Figure 175 Tightening the cable gland 7

Close the lid. Fix the lid with 14 M5 screws. The torque for the plastic screws is 0.3 Nm (0.2 ft-lb).

8

Fix the mounting brackets on each side of FODA front panel. See the figure below. The mounting brackets are required if FODA is installed in a rack or in a 3U casing together with FPFC, for example. Use TORX T20 screwdriver.

150


DN09142359



Figure 176 Fixing the mounting brackets 9

Fix the FODA unit to the rack using the mounting brackets on both sides of the unit. Or Fix FODA to a 3U casing on top of FPFC and secure the casing with two screws in the topmost position in the stack. 1. Install FPFC first in the casing using either the lower or upper fixing points of FPFC with one cage nut. 2. Install FODA on top of FPFC and fix it with two screws, one cage nut on both sides. See the figure below. 3. Fix the cable entries to the casing with one M5 x 10 screw on both sides of FPFC. Use the lower fixing points of the cable entry.

Figure 177 Installing FODA in a 3U casing together with FPFC

DN09142359


151



If required, FODA can also be installed on top of a casing. See the steps and figure below. 1. Fix the mounting brackets to the casing with two screws. Fix the right-hand mounting bracket first, using the side of the FODA to guide the installation. 2. Fix the left-hand mounting bracket. Note the installation direction of this bracket in the figure below. 3. Fix FODA on top of the casing with two screws on both sides.

3

2

1

3 2

Figure 178 Installing FODA on top of a casing. 10

Connect the optical cabling as required by the configuration. Attach the connector seals to protect the unused connectors, if there are any.

11

152

Attach the front cover, if required.


DN09142359


15.2

Installing Flexi Fiber Optical Distribution unit (FODA) on a wall Follow these instructions to install FODA unit on a wall. Steps

1


1

2

Figure 179 Opening the lid of FODA 2


3


DN09142359


153


Cable 12

12 11 10 9 8 7

6 5 4 3 2 1

Cable 1 2

1


Attach the input fiber cables to the relevant connectors inside FODA. See Figure 180 Routing cables through the cable gland for example routing. The cables are numbered, so make sure to attach the cables to appropriate connectors.

5

Tighten the cable gland. See the figure below. The torque for the cable gland is 0.7 Nm (0.5 ft-lb).

154


DN09142359


Make sure the cable IP sleeve is installed so that it goes through the gland as in the figure below.

Cable IP sleeve



7

Fix the mounting brackets on each side of FODA. See the figure below. Use a TORX T20 screwdriver.

Figure 182 Fixing the mounting bracket and the cable tie bracket

DN09142359


155


8

Fix the cable tie bracket. Fix the cable tie bracket on the same side as the cable gland to make cable routing easier. See Figure 182 Fixing the mounting bracket and the cable tie bracket.

9

Attach the FODA unit on a wall using the mounting brackets. See the figure below. Note that you need to choose the correct screws according to the wall material.

Figure 183 Installing FODA on wall 10

Connect the optical cabling as required by the configuration. Attach the connector seals to protect the unused connectors, if there are any.

11

Route the cabling to the side of the unit using the cable tie bracket.

12

Attach the FODA front cover, if required. See the figure below for the steps.

156


DN09142359


1

2

3 Figure 184 Installing the front cover

DN09142359


157


15.3

Installing Flexi Fiber Optical Distribution unit (FODA) on a pole Follow these instructions to install FODA unit on a pole. Steps

1


1

2

Figure 185 Opening the lid of FODA 2


3


158

Id:0900d805809a997d Confidential

DN09142359


Cable 12

12 11 10 9 8 7

6 5 4 3 2 1

Cable 1 2

1


Attach the input fiber cables to relevant connectors inside FODA. See Figure 186 Routing cables through the cable gland for example routing. The cables are numbered, so make sure to attach the cables to appropriate connectors.

5

Tighten the cable gland. See the figure below. The torque for the cable gland is 0.7 Nm (0.5 ft-lb).

DN09142359


159


Make sure the cable IP sleeve is installed so that it goes through the gland as in the figure below.

Cable IP sleeve



7

Fix the mounting brackets on each side of FODA. See the figure below. Use a TORX T20 screwdriver.

Figure 188 Fixing the mounting bracket and the cable tie bracket

160


DN09142359


8

Fix the cable tie bracket. Fix the cable tie bracket on the same side as the cable gland to make cable routing easier. See Figure 188 Fixing the mounting bracket and the cable tie bracket.

9

Connect the optical cabling as required by the configuration. Attach the connector seals to protect the unused connectors if there are any.

10

Route the cabling to the side of the unit using the cable tie bracket.

11

Attach the FODA unit on the pole using the mounting brackets. See the figure below. Use the included straining straps to mount FODA on the pole.

DN09142359


161


Figure 189 Installing FODA on a pole 12

Attach the FODA front cover. See the figure below for the steps.

162


DN09142359


1

2

3 Figure 190 Installing the front cover

DN09142359


163

Installing Flexi System External Alarm (FSEB)


16 Installing Flexi System External Alarm (FSEB) 16.1

Installing Flexi System External Alarm (FSEB) Before you start Before installing the FSEB, see FSEB interface signals and connector pin assignments. In pole or wall installations, locate the box in the proximity of the System Module. In wall installations, make sure that the mounting surface is flat. The distance from the FSEB to the System Module is limited by the length of the alarm cable. If using Flexi Mounting Auxiliary Brackets (FMAA), see the following figures for the installation position of the FSEB on the module casing.

FMAA

FMAA FSEC

FSEC

FSEC FMAA

FSEC

DN70456974

Figure 191 FMAA with FSEB

164

Id:0900d80580a3022c Confidential

DN09142359



FMAA

FMAA FSEB

FSEB FMAA FSEC FSEC

DN70456959

Figure 192 FMAA with FSEB and FSEC In FCIA and FCOA installations, use the fixing points on the cabinet roof.

Figure 193 FSEB fixing points on the FCIA roof

DN09142359


165



1.

2.

3.

Figure 194 FSEB fixing points on the FCOA roof

w

NOTICE: Electrostatic discharge (ESD) may damage the equipment. Wear an ESD wrist strap when handling the external alarm connection box. When connecting the cables, make sure that the cable lead-ins that are not used are blocked. A module ground cable is not included in the FSEB delivery. The minimum cross-section of the cable should be 2.5 mm2 (14 AWG). The length of the cable should be determined based on the FSEB installation option. Summary The FSEB can be installed either horizontally (cable lead-ins on the side) or vertically (cable lead-ins facing downwards, or left or right). See the following figures for the two installation options.

166


DN09142359



DN70284412

Figure 195 FSEB installed horizontally

DN70284424

Figure 196 FSEB installed vertically In outdoor installations, the cable lead-ins must be facing downwards, left or right to meet the IP55 standard.

DN09142359


167



ESD

Grounding point EAC M16 UltraSite and Talk swap cases BTS interconnection cable DN70283679

max 500mm (19.7 in.)

Figure 197 FSEB connectors

Cable fixing

DN70425315

168


DN09142359



When the cable is routed down, tie the cable a maximum of 500 mm (19.7 in) away from the FSEB to prevent the weight of the cable to break the cable lead glands of the FSEB. Figure 198 Fixing FSEB cables Steps 1

Install FSEB with four M5 screws using the fixing holes in the bottom of the box.

DN70284436

Figure 199 Install FSEB with four M5 screws Note that you do not need to open the box to install it. In stack, wall or pole installation, install the FSEB using the mounting brackets. See Installing Flexi Mounting Auxiliary Brackets (FMAA) for installation instructions. 2

Ground the box using the grounding screw on the right side of the FSEB front plate. Fix the nut tightly.

DN09142359


169



3

2

DN70285041

Figure 200 Connect the grounding cable 3

Connect the ESD wrist strap first to your wrist and then to the grounding clip next to the grounding screw.

4

Open the lid of the FSEB box. If using 12 alarms, set jumper X1103 to 12 Alarms mode. If using 24 alarms, set the jumper to 24 Alarms mode. For WCDMA, 24 alarms support is enabled if FSEB version is 471424A.304 or newer, System Module version is FSMC/D/E and software release is WN6.0 MP3 or newer. For LTE, only 12 Alarms mode is supported.

12 Alarms 24 Alarms

DN70425712

Figure 201 Jumper X1103 in 12 Alarms mode

170


DN09142359


5


Connect the external alarms cable (included in the FSEB delivery) from the FSEB to the System Module.

5

DN70285977

Figure 202 Connect the external alarms cable a) Pull the left U-shaped cable gland from the FSEB box. b) Remove the hole closing plug from the cable gland. If the plug is fixed with a cable tie, cut the cable tie first and remove it. c) Insert the cable in the cable gland. The D-Sub plug must point to the inside of the box. d) Connect the D-Sub plug to the leftmost D-Sub connector X1101 (ESM) on the FSEB board. e) Fix the connector fixing screws. f) Insert the U-shaped cable gland to the front plate. g) Insert the cable to the round rubber-seal in front of the U-shaped cable gland. h) Fix the cable with a cable tie. Make sure that the U-gland fixes the cable tightly. The cable must not move inside the gland. i) Route the cable between the FSEB and System Module and fix it with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). j) Remove the cover of the EAC connector on the System Module.

DN09142359


171



k) Insert the other end of the cable with the MDR-36 connector to the EAC connector of the System Module. Make sure that the MDR connector is firmly in place. l) Push the connector cover over the MDR connector and seal the EAC connector at the System Module with this cover. 6

If you are using an existing alarm cable (cable diameter min. 4-6 mm, ovality 1 mm) with a 37-pole D-Sub connector, connect the cable with a D-Sub connector as follows:

t

These two alarm cables can be connected to the EACX-I and EACX-II connectors of the FSEB, respectively. Connect the BTS alarm cables 1-12 and 13-24 to EACX-I and EACX-II connectors. Note that signals ext_al 13...24 are considered in BTS commissioning and fault handling as external alarms with IDs from 15 to 26. Pay attention to connect them to the right EACX connector, otherwise the alarm number and alarm description will not match. After the installation, trigger and verify the alarm condition using the Flexi BTS Site Manager. a) b) c) d)

Pull the right U-shaped cable gland from the FSEB box. Cut the cable tie off the cable gland. Remove the hole closing plug from the cable gland. Insert the alarm cable in the cable gland. The D-Sub plug must point to the inside of the box. e) Attach the D-Sub plug to the right 37-pole D-Sub connector X4101 (EACX-I port). f) Fix the connector fixing screws. g) Insert the U-shape cable gland to the front plate. h) Insert the cable to the round rubber-seal in front of the U-shaped cable gland. i) Fix the cable with a cable tie. Make sure that the U-gland fixes the cable tightly. The cable must not move inside the gland. j) Route the cable and fix it with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). 7

If you are using the separate alarm cables, connect them to the screw terminals as follows: a) Tighten the cable gland nut. The cable must not move inside the gland. b) Insert the alarm cables in the FSEB box by using the cable glands on the right-side half of the FSEB box. c) Route the alarm cables and fix them with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). d) Attach alarm lines EXT_AL1 to EXT_AL12 using screw terminal blocks X4106X4109. e) For each alarm input, connect one wire to the GROUND screw terminal blocks X4107 or X4109 and connect one wire to the selected alarm input on screw terminal blocks X4106 or X4108. The alarm inputs are marked on the FSEB board with 'EXT_AL6 ... EXT_AL1' on X4106 and 'EXT_AL12 ... EXT_AL7' on X4108.

t 172

If you use alarm inputs on the EACX-I port (D-Sub connector X4101), do not use the same alarm inputs on the screw terminals X4106 and X4108.


DN09142359


8


If you are using the control output cables, connect them as follows: a) Tighten the cable gland nut. The cable must not move inside the gland. b) Insert the control output cables in the FSEB box by using the cable glands on the right-side half of the box. c) Route the control cables and fix them with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). d) Attach the control lines EXT_CO1 to EXT_CO6 by using the screw terminal blocks X4104 and X4105. e) Control outputs are open collector type. Connect a pull-up resistor (2-6 kilohms, 5 kilohms is recommended) or an optocoupler to +5 V to ensure correct operation. The control outputs are marked on the FSEB board with 'EXT_CO6 ... EXT_CO1' on X4104. FSEB / System Module

PS

OCP

+5V

RPullUp 2...6kOhm

600 ohm

To customer application

OVP

EXT_CO1...EXTCO6 (Pins 1...6)

CTRL EAXC I EAC

FSEB / System Module

PS

OCP

+5V

Optocoupler

To customer application ~160 ohm OVP

EXT_CO1...EXTCO6 (Pins 1...6)

CTRL EAXC I EAC

DN70680696

Figure 203 Control outputs

g DN09142359

If galvanic isolation is required for the customer application, see the figure above for an example with an optocoupler. Follow the country-specific safety requirements.


173


t 9


If you use control outputs on the EACX-I port (D-Sub connector X4101), do not use the same control outputs on the screw terminal X4104.

Install the fire detector to the FSEB (optional). a) Connect the fire detector to the FSEB using a four-wire cable. Two wires are needed for fire detector power supply and two for the fire detector alarm connection. b) Attach the four wires of the cable to the fire detector relay-base. c) Insert the other end of the four wire cable through one cable gland at the right half of the FSEB box. d) Tighten the cable gland nut. The cable must not move inside the gland. e) Route the cable and fix it with cable ties. The first fixing point must not be further away from the FSEB box than 0.5 m (1.6 ft). f) Attach the wire marked with + from the fire detector to the leftmost or rightmost opening of the screw terminal X4114. g) Attach the wire marked with - from the fire detector to one of the four middle openings of the screw terminal X4114 marked with GND. See Fire detector power supply interface in FSEB interface signals and connector pin assignments. h) Attach the fire detector alarm wires to one of the alarm inputs 'EXT_AL12 ... EXT_AL1'.

10

Install the cover of the FSEB box and tighten the eight screws to 1.7 Nm (1.25 ftlb.).

DN70285053

Figure 204 Install the cover

174


DN09142359


16.2

FSEB interface signals and connector pin assignments EACX-II Connector ESM Connector

Fire Detector Power Supply output

EACX-I Connector

Alarm Inputs

Control Outputs

5V EAC Output

Ground Connections

Figure 205 FSEB printed wiring board EACX connector I pin assignment Pin

Pin

Signal

1

EXT_CO1

19

GND

2

EXT_CO2

20

+5V/30mA

3

EXT_CO3

21

+5V/30mA

4

EXT_CO4

22

+5V/30mA

5

EXT_CO5

23

+5V/30mA

6

EXT_CO6

24

+5V/30mA

7

EXT_AL1

25

+5V/30mA

8

EXT_AL2

26

GND

9

EXT_AL3

27

GND

10

EXT_AL4

28

GND

11

EXT_AL5

29

GND

12

EXT_AL6

30

GND

13

EXT_AL7

31

GND

14

EXT_AL8

32

GND

15

EXT_AL9

33

GND

Table 5

DN09142359

Signal

EACX connector I pin assignment (Sub-D37)

Id:0900d80580848bd8 Confidential

175


Pin

Signal

Pin

Signal

16

EXT_AL10

34

GND

17

EXT_AL11

35

GND

18

EXT_AL12

36

GND

-

-

37

GND

Table 5

EACX connector I pin assignment (Sub-D37) (Cont.)

EACX connector II pin assignment EACX connector II is not used in the 12 Alarms mode. Pin

Pin

Signal

1

EXT_AL13

19

GND

2

EXT_AL14

20

GND

3

EXT_AL15

21

GND

4

EXT_AL16

22

GND

5

EXT_AL17

23

GND

6

EXT_AL18

24

GND

7

EXT_AL19

25

GND

8

EXT_AL20

26

GND

9

EXT_AL21

27

GND

10

EXT_AL22

28

GND

11

EXT_AL23

29

GND

12

EXT_AL24

30

GND

13

Not used

31

Not used

14

Not used

32

Not used

15

Not used

33

Not used

16

Not used

34

Not used

17

Not used

35

Not used

18

Not used

36

Not used

-

-

37

Not used

Table 6

176

Signal

EACX connector II pin assignment (Sub-D37)


DN09142359


Screw terminal pin assignment Signal

Signal

Screw terminal1)

EXT_CO1

Connector X4104 pin 1

+5V


EXT_CO2


+5V


EXT_CO3


+5V


EXT_CO4


+5V


EXT_CO5


+5V


EXT_CO6


+5V


EXT_AL1


GND


EXT_AL2


GND


EXT_AL3


GND


EXT_AL4


GND


EXT_AL5


GND


EXT_AL6


GND


EXT_AL7


GND


EXT_AL8


GND


EXT_AL9


GND


EXT_AL10


GND


EXT_AL11


GND


EXT_AL12


GND


Table 7

DN09142359

Screw terminal

Screw terminal pin assignment


177


Signal

Screw terminal

Signal

Screw terminal1)

EXT_AL13


GND


EXT_AL14


GND


EXT_AL15


GND


EXT_AL16


GND


EXT_AL17


GND


EXT_AL18


GND


EXT_AL19


GND


EXT_AL20


GND


EXT_AL21


GND


EXT_AL22


GND


EXT_AL23


GND


EXT_AL24


GND


Table 7 1)The

Screw terminal pin assignment (Cont.)

X connectors are marked on the bottom of the FSEB PCB.

Fire detector power supply interface Pin 1

+8.55V ... +11.5V

2

Ground

3

Ground

4

Ground

5

Ground

6

+8.55V ... +11.5V

Table 8

178

Signal

Fire detector power screw terminal X4114 pin assignment


DN09142359


16.3

EAC cable (FTSI 472578A) wiring Conn. 1 (HDMI) Conn. 2 (D37)

Description

Pin no.

Pin no.

1

7

1: Black

EXT_AL0_H

2

8

2: Brown

EXT_AL1_H

3

9

1: White/Black

EXT_AL2_H

4

10

2: White/ Brown

EXT_AL3_H

5

11

3: Red

EXT_AL4_H

6

12

4: Orange

EXT_AL5_H

7

1 + 13

3: White/Red

EXT_CTRL0_EXT_A L6_H

8

2 + 14

4: White/Orange


9

3 + 15

5: Yellow


10

4 + 16

6: Green


11

5 + 17

5: White/Yellow


12

6 + 18

6: White/Green


13

19

7: Blue

P5V0_EAC

14

20

7: White/Blue

P5V0_EAC

15

23

8: Violet

PROT_CAN_H_P5V_ EAC

16

27

9: Grey

GND

17

24

8: White/Violet

PROT_CAN_L_P5V_ EAC

18

25

10: Pink

GND

19

28

9: White/Grey

GND

Table 9

DN09142359

Pair: wire color

EAC cable (FTSI) wiring

Id:0900d805808efa9c Confidential

179

Installing GPS Antenna Kit (FYGA) or GPS GLONASS Receiver Antenna (FYGB)


17 Installing GPS Antenna Kit (FYGA) or GPS GLONASS Receiver Antenna (FYGB) Purpose This section provides instructions for installing the GPS (Global Positioning System) or GNSS (Global Navigation Satellite System) system.The following items are available: • • •

GPS Antenna Kit (FYGA) 471442A GPS GLONASS Receiver Antenna (FYGB) 472748A Optional items: • GPS Mounting Kit (FYMA) 471605A • Flexi GPS Surge Protection Kit (FYEA) 471822A • Power/data cables: • GPS cable set (FYHA) up to 30 m 471606A • GPS cable set (FYHB) up to 100 m 471653A • GPS cable set (FTSE) up to 30 m 472510A (for System Module variant FSMF) • GPS cable set (FTSH) up to 100 m 472577A (for System Module variant FSMF)

FTSE

FTSH

FYGA/B

FYHA

FYHB FYMA

Figure 206 GPS hardware Follow the general guidelines for locating the GPS/GNSS antenna to provide safe and clear satellite visibility. See section Satellite visibility below for more details.

180

Id:0900d80580a2ac0b Confidential

DN09142359



Satellite visibility Note that a 180º clear sky view is the optimum case from the signal quality and accuracy point of view. If the clear sky view is smaller than 180º (for example urban canyons), the GPS/GNSS receiver operation might suffer from poor satellite visibility, depending on the sky view angle and location on the globe (especially latitude). The GPS/GNSS receiver might be operational, especially after the survey, even with smaller than a 180º sky view, however, this cannot be guaranteed. Furthermore, the survey time might be longer and the accuracy of the PPS signal poorer than with a full 180º sky visibility.

GPS view GPS satellite GPS satellite

GPS satellite

GPS satellite

GPS satellite

GPS satellite 180

180

GPS antenna

With proper sky view (satellite visibility) the survey time is less than 60 minutes. Note: Good constellation (i.e. a PPs quality signal) requires 4-5 visible satellites, depending on the satellite constellation situation. In practice it means a 180 open view.

GPS antenna

After survey: One satellite is enough for the GPS receiver to provide the PPS reference signal for the BTS. The PPS accuracy with only one satellite is, however, poorer than with a larger number of satellites (i.e. with good sky visibility). DN70433373

Figure 207 GPS view Steps 1

Install the GPS Mounting Kit (FYMA). a) To attach the kit to a wall, use the screws.

DN09142359


181



2

3

1a

Figure 208 Installing the GPS/GNSS system on the wall b) To attach the kit to a pole, use the bands and fasten them with screws.

2

3

1b

Figure 209 Installing the GPS/GNSS system on the pole The following table presents the GPS/GNSS pole mounting band cutting rule.

182


DN09142359



Pole diameter

Cutting length

50 mm (1.9 in)

107 mm (4.2 in)

80 mm (3.1 in)

201 mm (7.9 in)

110 mm (4.3 in)

296 mm (11.6 in)

150 mm (5.9 in)

421 mm (16.5 in)

200 mm (7.8 in)

578 mm (22.7 in)

250 mm (9.8 in)

804 mm (31.6 in)

300 mm (11.8 in)

893 mm (35.1 in)

Table 10

GPS/GNSS pole mounting band cutting rule

Note that the 25 mm (0.9 in) bending lengths for both ends are included in the cutting lengths. The metal band folds must be inwards folded and so that folds are compressed against the pole while tightening the band.

Worm screw Metal band

Worm screw housing

Locking rack

Figure 210 Pole mounting bands

t

DN09142359

To ease the tightening of the bands, locate the worm screw on the other side of the pole than the fastener.

2

Attach the GPS/GNSS receiver to the mounting kit.

3

Secure the GPS/GNSS receiver using the mounting kit locking nut.

4

Connect the GPS/GNSS receiver cable to the GPS/GNSS receiver.

5

Route the cable through the holes in the mounting kit.

6

Secure the cable with the cable ties.


183


7


Connect the other end of the GPS/GNSS cable to the Sync In port on the System Module front panel. Expected outcome

Figure 211 Pole mounting

184


DN09142359


Installing Flexi GPS Surge Protection Kit (FYEA)

18 Installing Flexi GPS Surge Protection Kit (FYEA) Purpose The Flexi GPS Surge Protection Kit (FYEA) assembly protects the Flexi System Module against transient voltage and current spikes in the GPS antenna line. There are two mounting kits for the FYEA: • •

Flexi Mounting Auxiliary Brackets (FMAA) for stack installations Flexi Pole Installation Kit (FPIA) for pole and wall installations

The FYEA box is connected between the System Module and the GPS antenna. The FYEA can also be installed on FCOA roof. The fixing points on the cabinet roof are illustrated in the following figure.

1.

2.

3.

Figure 212 FYEA fixing points on the FCOA roof

DN09142359

Id:0900d805809d6c0a Confidential

185



Steps 1

Open the lid of the FYEA box.

1

DN70525477 Figure 213 Opening the FYEA lid 2

Install the box. In outdoor installations, the FYEA must be installed maximum 10 meters (33 ft.) from the System Module. Note that the length of the GPS cable is 30 or 100 metres (98 or 328 ft.). In pole installations, use the FPIA kit: a) Thread the straining straps to the installation plate. b) Tighten the straining straps around the pole.

186


DN09142359



2b 2a

DN70525656 Figure 214 Threading the straining strap 3

Connect the grounding cable. Route the grounding cable from the bottom right corner of the FYEA box to the grounding point on the plinth.

DN09142359


187



3

DN70525668 Figure 215 Connecting the grounding cable 4

Cut the GPS cable. Cut the GPS cable and remove around 70 mm (2.76 in) of the cable jacket and 8 mm (0.31 in) of the wire covering.

188


DN09142359



8 mm (0.31 in) 70 mm (2.76 in)

DN70525683 Figure 216 Exposing the wires 5

Connect the cables to the FYEA box. Connect the wires to the FYEA box in the following way: Surge protector

Pair number Color

Position IN (to System Module)

Position OUT (to GPS antenna)

1

4

Brown

7

8

White

1

2

Green

11

12

White

5

6

Orange

7

8

White

1

2

Blue

11

12

White

5

6

3

2

2

1

Table 11

DN09142359

FYEA connections


189



To GPS Antenna

OUT

1

2

IN

From System Module

DN70522429 Figure 217 Connecting cables

190


DN09142359


6


Connect the cable shielding to the PE terminals.

1

2

DN70522432 Figure 218 Connecting cable shielding 7

DN09142359

Route the GPS cables to the System Module and to the GPS antenna respectively.


191


8


Check the FYEA connections and close the lid.

8

DN70525741 Figure 219 Closing the FYEA lid 9

192

Connect the GPS cable ends to the System Module and GPS antenna respectively.


DN09142359


Installing Flexi GPS Box (FYGD)

19 Installing Flexi GPS Box (FYGD) Before you start

g

Note that Flexi GPS Box (FYGD) is IP20-rated and for indoor site use only. If cable entries are installed, remove them.

SMA Female

GNSS Ant

HDMI

See Figure 220 Flexi GPS Box (FYGD) front panel for external interfaces of FYGD.

GNSS RJ45

Sync Out 1588 In

RJ45

1588 Out

1588

Status

PWR On/Off

Figure 220 Flexi GPS Box (FYGD) front panel Steps 1

Remove the FPFD dummy unit as follows: a) Undo the screws holding the FSMx core in place. b) Pull out the core. c) Remove the three screws holding the FPFD dummy unit in place.

g

DN09142359

Leave the other dummy units in place if you are not installing any other optional submodules.


193



a)

b)

c)

Figure 221 Removing dummy unit 2

Fix the FYGD to the FSMF core. FYGD is fixed with the three screws that are included in the FYGD delivery. See figure below.

194


DN09142359



Figure 222 Fixing FYGD to core 3

Re-insert the module core and fix the screws.

4

Connect the 1PPS source from the GNSS antenna to GNSS ANT connector.

Figure 223 1PPS connection 5

Connect the 1PPS sync cable from the Sync Out connector to the Sync In connector on the FSMF on which the FYGD is installed. Use the 0.6 m (2 ft.) cable.

DN09142359


195



Figure 224 Connecting sync cable 6

If required, switch the timing resource. FYGD uses GNSS as default setting for the timing resource, but if required, the 1588 setting can be selected using the switch on the FYGD front panel.

7

196

Switch the FYGD On.


DN09142359


Installing UltraSite Outdoor Side Kit (OSKA)

20 Installing UltraSite Outdoor Side Kit (OSKA) Purpose The UltraSite Outdoor Side kit (OSKA) is used to enhance current UltraSite BTS's by adding FlexiBTS modules to it without the need of adding an extra cabinet. The OSKA kit can be used with the ODCA cabinet. The following cabinet do not support the kit yet: • • •

CRMA + OAKA CRMA + OAKB and ODCF

Before you start Ensure that the BTS cabinet is grounded properly to ensure personnel safety and to avoid electrostatic discharge which can damage the equipment.

f Danger of Lethal Voltages! Ensure that the site has a main switch for disconnecting power and that the mains power breaker is off before installing the OSKA Side Kit. Summary The side kit allows both WCDMA and GSM/EDGE Flexi modules to be connected to it, with each module being housed within a Flexi housing. The Flexi Rectifier Module (FPRA) can also be mounted directly to the side kit without the need of a Flexi housing. The side kit can be fixed to either the left hand side (LHS), right hand side (RHS) or rear of an Ultrasite Outdoor cabinet. A maximum of two modules can be stacked on top of each other in three fixing points (a total of six Flexi modules). The maximum weight on one plate is 130 kg. Note that only two faces of an Ultrasite Outdoor cabinet can be used at any one time, which are LHS and rear or RHS and rear. For details see the figure below:

DN09142359

Id:0900d805806e63d7 Confidential

197



F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

REAR

REAR

Figure 225 Side kits fixed to the cabinet The side kit can also be used with 2 off 471614A Flexi Mounting Shields 6U (FMSA) per side plate where extra protection of the Flexi modules is required. The maximum weight on one plate is 130 kg. Steps 1

Secure the side plate to the side of the Ultrasite ODCA Cabinet using 6 of M6 x 20 torx screws, flat washers and star washers. Ensure that the two wall brackets are connected properly.

2

Adjust the side wall plate so that it is touching the ground or the cabinet mounting platform. This helps support the weight of the plate and mounted modules prior to tightening of the fixings. Tighten M6 screws to 5Nm. If the side plate is to be mounted on the rear of the cabinet, the wall brackets should be secured between the A fixing positions of top 2 rear corners of the cabinet. If the side plate is to be mounted on the rear of the cabinet as well as one of the sides, 4 of the wall brackets should be used between the A fixing positions of the 2 rear corners of the cabinet.

198


DN09142359



A

A Wall bracket M6 Torque screw, star and flat washers M6 Torque screw, star and flat washers A

A Wall bracket M6 Torque screw, star and flat washers M6 Torque screw, star and flat washers

Figure 226

DN09142359

Installing an OSKA Side Kit


199

Installing UltraSite IDC_ Roof Kit (IRSA)


21 Installing UltraSite IDC_ Roof Kit (IRSA) 21.1

Installing UltraSite IDC_ Roof Kit (IRSA) Purpose The UltraSite IDC_ Roof Kit (IRSA) is used to install a Flexi Rectifier module (FPRA), or any other Flexi unit, on the roof of an UltraSite Indoor cabinet. The FPRA is configured as part of the respective BTS and forms a fully integrated solution for sites requiring battery backed-up facility. For this application, either the FPRA or Flexi Modules can be installed. Three Flexi modules can be installed into IRSA roof kit on cabinet roof. Maximum weight of modules on roof is 53 kg. Preconditions Remove the assembled IRSA UltraSite IDC_ Roof Kit from its packaging. Disassemble the Kit into the parts and check the contents against those detailed in IDC_Roof kit (IRSA) delivery contents. Mask upper

Torx screw M5x10 Ferritic stainless steel Connection pin

Hex nut M8 A4 4 pcs Rivet 4.0x7.6

Washer M8

ESD stud Adapter plate Mounting rail 2 pcs

M5x10 screw 2 pcs

M8 washer M8 screw

Support rail 4 pcs

Washer 2 pcs

Plastic washer 2 pcs Mask side 2 pcs

Mask front

Torx screw M5x10 Ferritic stainless steel

Figure 227 IRSA Roof Kit Grounding is required to ensure personnel safety and to avoid electrostatic discharge which can damage the equipment. Ensure the BTS cabinet is grounded as required.

f Danger of Lethal Voltages! Ensure that the site has a main switch for disconnecting power and that the mains power breaker is off before installing the IRSA UltraSite IDC Roof Kit.

200

Id:0900d805806e63eb Confidential

DN09142359


Installing UltraSite IDC_ Roof Kit (IRSA)

Summary The IRSA Roof Kit can be installed in normal or forward position or it can be mounted on the side wall of the IDCA cabinet.

DN09142359

Id:0900d805806e63eb Confidential

201


21.2

Installing UltraSite IDC_ Roof Kit (IRSA) in normal position Steps

1

Connect the -48V DC and DC return power cables to the IDCA antenna box, situated on the top of the cabinet.

2

Fit any other cabling to the antenna box, such as alarm or antenna cables, prior to fitting the IRSA Roof Kit.

3

Fit the four support rails into the M12 eyebolt fixing positions on the top of IDCA cabinet. Use a 13mm spanner to tighten.

4

Fit the mounting rails and the adapter plate over the support bars. Secure with M8 Hex nuts and washers. Tighten to 20Nm maximum. See the figure for details: 3.

4.

Figure 228 Fitting the support, mounting rails and adapter plate to the IDCA cabinet 5

Installing FPRA Before you start

f Electrostatic discharge (ESD) may damage the equipment. Wear an ESD wrist strap when handling the external alarm connection box.

202

Id:0900d805806e63e5 Confidential

DN09142359


Steps a

Fit the FPRA to the adapter plate using the 4 connection pins located on adapter plate which align with keyhole slots in the FPRA base. Further information

Figure 229 Mounting the FPRA on the adapter plate b

Secure the unit in position using 2 of the M5 torx screws. Tighten to 2Nm maximum.

c

Connect the FPRA TE terminal to the adaptor plate’s M5 ground fastener. Use the earth cable supplied with the FPRA. Refer to the FPRA Installation Manual for details of the TE terminal position and cable installation procedure.

d

Connect the adaptor plate’s M8 ground fastener to the UltraSite indoor cabinet's earth point, which is located on its roof, Use cable 995215A which is supplied with the IRSA Ultrasite IDC_ Roof Kit.

e

Connect the -48V DC, DC return power cables and alarm cables to the FPRA. Make sure that you do so in accordance with the manufacturer's installation instructions.

6

Fitting the mask Steps a

Fit the mask sides to the adapter plate. Loosely secure them with 4 of the M5X10 Torx screws.

b

Align the mask front and secure it using 2 of the M5x10 Torx screws. Tighten to 2Nm maximum.

c

Fit the mask upper to the adapter plate by locating the keyholes in the cover.

d

Fix into position using 4 off M5x10 Torx screws. Tighten to 2Nm.

DN09142359


203


e

The installation is completed. Further information a.

b.

c.

Figure 230 Fitting the masks

204


DN09142359


21.3

Installing UltraSite IDC_ Roof Kit (IRSA) in forward position Purpose For improved access to the Antenna Connections on the IDCA Antenna Box, the adaptor plate can be fitted in a forward position, which overhangs the front of the IDCA cabinet.

Figure 231 FPRA installation in forward position Steps 1

Fit -48V DC and DC return power cables to IDCA antenna box, situated on the top of the cabinet.

2

Fit other cabling to the antenna box, such as alarm cables and so on, prior to fitting IDC_ Roof Kit.

3

Fit the four support rails. For details see as described in section Installing UltraSite IDCA Roof Kit (IRSA) in normal position.

4

Fit the mounting rails.

5

Fit the adapter plate in the forward position. Use the second M8 hole in from the forward edge of the adapter plate. Secure with M8 nuts in this position. Ensure the slots in the Adapter plate are at the back.

6

Fit the FPRA to the adapter plate. Use 4 of the connection pins located on the adapter plate, which align with the keyhole slots in the FPRA. Secure the unit in position. For details see as described in section Installing UltraSite IDCA Roof Kit (IRSA) in normal position

DN09142359


205


7

Connect the FPRA TE terminal to the adaptor plate’s M5 ground fastener. Use the earth cable supplied with the FPRA. Refer to the relevant FPRA installation manual for details of the TE terminal position and cable installation procedure.

8

Connect the adaptor plate’s M8 ground fastener to the UltraSite IDC_ earth point on its roof. Use cable 995215A which is supplied with the IRSA Ultrasite IDC_ Roof Kit.

9

Connect the -48V DC and DC return power cables to the FPRA unit. For details, refer to the manufacturer's installation guides.

10

Fit any other cabling to FPRA, such as alarm cables. Make sure you do so in accordance with the manufacturer's installation guide.

11

Fit the mask sides and mask front to the adapter plate. For details see as described in section Installing UltraSite IDCA Roof Kit (IRSA) in normal position

12

Fit the upper mask to adapter plate. Locate the keyholes in the cover over 4 of the M5x10 Torx screws and then tighten the screws.

13

206

The assembly is complete.


DN09142359


Appendix Contents of deliveries

22 Appendix Contents of deliveries 22.1

Contents of the System Extension Kit (FSKA) delivery The System Extension Kit (FSKA) delivery contains the following items: Description

Quantity

Flexi System Extension Kit (FSKA) 471226A

1

Accessories for FSKA:

1

•

Optical cable, 2m (6.6 ft.)

2

•

Power cable, 2m (6.6 ft.)

1

•

Optical transceiver

4

Transmission dummy panel

1

M5 x 25 screw

4

Table 12

DN09142359

Product code

System Extension Kit (FSKA) delivery content

Id:0900d80580a2abbf Confidential

207


22.2

Contents of the System Extension Kit (FSKB) delivery The System Extension Kit (FSKB) delivery contains the following items: Description

Quantity

Flexi System Extension Kit (FSKB) 472302A

1

Accessories for FSKB:

1

•

Optical cable, 4m (13.1 ft.)

2

•

Power cable, 4m (13.1 ft.)

1

•

Optical transceiver

4

Transmission dummy panel

1

M5 x 25 screw

4

Table 13

208

Product code

System Extension Kit (FSKB) delivery content

Id:0900d805808c2517 Confidential

DN09142359


22.3

Contents of the Flexi Pole Installation Kit (FPIA) delivery Description Flexi Pole Installation Kit (FPIA):

Product code 471767A

Quantity 1

•

Installation plate

1

•

Straining strap

1

•

M5 screws

4

Table 14

The Flexi Pole Installation Kit (FPIA) delivery content

See the following figure for more information on the delivery contents.

DN70458645

Figure 232 Delivery contents of the FPIA

DN09142359

Id:0900d80580999d67 Confidential

209


22.4

Contents of the Flexi Mounting Auxiliary Bracket (FMAA) Description

Product code

Flexi Mounting Auxiliary Bracket (FMAA):

471657A

Quantity

•

Bracket

1

•

M5 x 16 screw

8

•

M4 x 10 screw

4

•

M5 x 10 screw

4

•

M5 spring washer

4

Table 15

Flexi Mounting Auxiliary Bracket (FMAA) delivery contents


Figure 233 Delivery contents of the FMAA

210


DN09142359


22.5

Contents of the 3U mounting covers (FMCA) delivery The front and back covers are an optional item that has to be ordered separately, when needed. The covers delivery contains the following items: Description

Product code

3U mounting covers (FMCA)

470239A

Quantity 1

•

Front cover

1

•

Back cover

1

•

Maintenance strap

2

•

Grounding cable

1

•

Cable entry

2

•

Cable entry screw (M5 x 10)

4

Table 16

3U mounting covers (FMCA) delivery content

See the following figure for more information on the delivery content.

Front cover

Back cover

2 x cable entry

2 x maintenance strap

Grounding cable

Figure 234 Delivery contents of the back and front covers

DN09142359

Id:0900d805809d61dc Confidential

211


22.6

Contents of the Flexi Mounting Covers Front and Back, 2U (FMCB) Description

Product code

Quantity

Flexi Mounting Covers Front and Back, 2U (FMCB)

470332A

1

•

2U front cover

1

•

2U back cover

1

•

Maintenance strap

2

•

Grounding cable

1

•

Cable entry

2

•

Cable entry screw

4

Table 17

The Flexi Mounting Covers Front and Back, 2U (FMCB), needed with Flexi Power DC/ DC Module 24 V (FPDA)

See the following figure for more information on the delivery content.

Front cover

Back cover

2 x cable entry

2 x maintenance strap

Grounding cable

Figure 235 Delivery contents of the back and front covers

212

Id:0900d80580999d65 Confidential

DN09142359


22.7

Contents of the 3U Module Casings (EMHA) delivery The 3U Module Casings (EMHA) delivery contains the following items: Description EMHA


Quantity 1

3U casing

1

•

3U cable entries

2

•

3U front cover

1

•

3U rear cover

1

•

M5 x 10 screws

4

•

M5 x 8 screws

2

•

Cage nuts

6 (2 loose, 4 preinstalled)

•

Maintenance straps

2

•

Grounding cable

1

•

Cable clamps

2

Table 18

DN09142359

(1 loose, 1 preinstalled)

The Flexi Module Casings for 3U modules (EMHA) delivery contents

Id:0900d80580995dee Confidential

213


Figure 236 EMHA delivery contents

214

Id:0900d80580995dee Confidential

DN09142359


22.8

Contents of the 2U Module Casings (EMTA) delivery The 2U Module Casings (EMTA) delivery contains the following items: Description EMTA

470315A

Quantity 1

2U casing

1

•

2U cable entries

2

•

2U front cover

1

•

2U rear cover

1

•

M5 x 10 screws

4

•

M5 x 8 screws

2

•

Cage nuts

4, preinstalled

•

Maintenance straps

2

•

Grounding cable

1

•

Cable clamps

2

Table 19

DN09142359

Product code

(1 loose, 1 preinstalled)

The Flexi Module Casings for 2U modules (EMTA) delivery contents

Id:0900d8058098d07b Confidential

215


Figure 237 EMTA delivery contents

216


DN09142359


22.9

Contents of the Flexi Side Covers (FMHA) delivery Flexi Side Covers (FMHA) for 3 height units (3U) delivery contains the following items: Description Flexi Side Covers (FMHA)

471524A

Quantity 1

•

3U Cable Tunnel Cover side

2

•

3U Cable Tunnel Cover front

2

•

M5 x 10 self-tapping screws

4

•

M5 Torx captive screws

2

Table 20

DN09142359

Product code

Flexi Side Covers (FMHA) delivery content

Id:0900d805809d66d6 Confidential

217


22.10

Contents of the Flexi Side Covers (FMTA) delivery Flexi Side Covers (FMTA) for 2 height units (2U) delivery contains the following items: Description Flexi Side Covers (FMTA)

471523A

Quantity 1

•

2U Cable Tunnel Cover side

2

•

2U Cable Tunnel Cover front

2

•

M5 x 10 self-tapping screws

4

•

M5 Torx captive screws

2

Table 21

218

Product code

Flexi Side Covers (FMTA) delivery content

Id:0900d805809d66da Confidential

DN09142359


22.11

Contents of the Flexi Mounting Shield 3U Casing (FMSC) delivery The optional Flexi Mounting Shield 3U Casing (FMSC) delivery contains the following items: Description FMSC


Quantity 1

3U casing

1

•

Cage nuts

4, preinstalled

•

Screws

2

Table 22

Flexi Mounting Shield 3U Casing (FMSC) delivery contents

Figure 238 FMSC delivery contents

DN09142359

Id:0900d8058098d0bb Confidential

219


22.12

Contents of the Power Module (FPMA) delivery The FPMA Power Module is an optional item that has to be ordered separately, when needed. Description Power Module (FPMA) with internal AC and DC cabling and cable support plates


Quantity 1

•

Alarm cable to the System Module, 2 m (6.6 ft.)

1

•

Power cable harness, 30, 40, 50 and 80 cm (11.8, 15.7, 19.7 and 31.5 inches)

1

•

Power cable, 1.2 m (4 ft.)

2

•

Power cable L, 10 cm (4 inches)

3

•

Cable clamps

2

•

K30 screws for the cable clamps

4

•

M5 screws for fixing the casing to another casing or plinth

2

•

Cable ties

10

•

AIr deflector

1

•

Screws for fixing the air deflector to the front cover

2

Table 23

The Power Module (FPMA) delivery content


220

Id:0900d805809a4c3a Confidential

DN09142359


10 x

Figure 239 Delivery contents of the FPMA

22.12.1

Contents of the power AC/DC sub-module (FPAA) delivery The FPAA power sub-module is an optional item that has to be ordered separately, when needed. Description Power sub-module (FPAA) with two RJ-45 connector seal caps installed


Quantity 1

•

Alarm cable

1

•

M5 screws for fixing the FPAA to FPMA

2

Table 24

The FPAA power sub-module delivery content


DN09142359


221


DN7090714

Figure 240 Delivery contents of the FPAA

22.12.2

Contents of the power battery sub-module (FPBA/B) delivery The FPBA/B power battery sub-module is an optional item that has to be ordered separately, when needed. Description

Product code

Power battery sub-module (FPBA/B) with two RJ-45 connector seal caps installed

470141A/47 2113A

Quantity 1

•

Alarm cable

1

•

M5 screws for fixing the FPBA/B to FPMA

2

Table 25

The FPBA/B power sub-module delivery content


DN7090726

Figure 241 Delivery contents of the FPBA/B

222


DN09142359


22.13

Contents of the 24V Power Module (FPDA) delivery The 24V Power Module (FPDA) is an optional item that has to be ordered separately, when needed. Description DC/DC converter core preinstalled inside a 2U casing with two RJ-45 connector seal caps installed


Quantity 1

•

DC output power cables

2

•

Alarm cable

1

•

AWG 4 (25 mm2) connector single rubber boot

4

•

M5 screws for fixing the casings to each other

2

•

Cable clamps

4

•

K30 screws for cable clamps

8

Table 26

The 24V Power Module (FPDA) delivery content


Figure 242 Delivery contents of the FPDA delivery

DN09142359

Id:0900d805809c82dc Confidential

223


22.14

Contents of the Flexi Power AC/DC sub-module (FPAC) delivery The Flexi Power AC/DC sub-module 230V (FPAC) delivery contains the following item: Description Flexi Power AC/DC sub-module 230V (FPAC) Table 27


Quantity 1

Flexi Power AC/DC sub-module 230V (FPAC) delivery content

Figure 243 FPAC delivery contents (FPAC top view)

224

Id:0900d8058098d4e4 Confidential

DN09142359


22.15

Contents of the Flexi Power AC/DC sub-module (FPAD) delivery The Flexi Power AC/DC sub-module (FPAD) delivery contains the following item: Description Flexi Power AC/DC sub-module (FPAD) Table 28


Quantity 1

Flexi Power AC/DC sub-module (FPAD) delivery content

Figure 244 FPAD delivery contents

DN09142359

Id:0900d805809a3df3 Confidential

225


22.16

Contents of the Flexi Power Distribution and Fuses Outdoor (FPFC) delivery The Flexi Power Distribution and Fuses Outdoor (FPFC) is an optional item that has to be ordered separately when needed. Description Flexi Power Distribution and Fuses Outdoor (FPFC)

472508A

Quantity 1

•

Washers

4

•

Cable clamps

2

•

Grounding cable

1

•

Alarm cable

1

•

Maintenance straps

2

•

M5 x 10 screws for fixing cable entries and grounding cable. Also two screws can be used as lock screws in casing installation

7

•

K30 screws for cable clamps

4

•

M5 x 6 screws for fixing two casings together

2

•

M5 screws for fixing FPFC to 2U casing

4

Table 29

226

Product code

Flexi Power Distribution and Fuses Outdoor (FPFC) delivery content

Id:0900d80580994e51 Confidential

DN09142359


Figure 245 FPFC delivery contents

DN09142359


227


22.17

Contents of the Flexi System External OVP (FSEC) delivery The Flexi System External OVP (FSEC) delivery contains the following items: Description Flexi System External OVP (FSEC)


Quantity 1

•

Grounding cable

1

•

Power cable

1

•

M5 x 16 screws

4

Table 30

Flexi System External OVP (FSEC) delivery content

Figure 246 FSEC delivery contents

228

Id:0900d805809d62a8 Confidential

DN09142359


22.18

Contents of the Flexi System External OVP (FSES) delivery The Flexi System External OVP (FSES) delivery contains the following items: Description Flexi System External OVP (FSES) with a pre-installed power output and grounding cable •


1

4

Screws (M5 x 8)

Table 31

Quantity

Flexi System External OVP (FSES) delivery content

Figure 247 FSES delivery contents

DN09142359

Id:0900d805809d62b4 Confidential

229


22.19

Contents of the Flexi Fiber Optical Distribution unit (FODA) delivery The Flexi Fiber Optical Distribution unit (FODA) is an optional item that has to be ordered separately when needed. Description Flexi Fiber Optical Distribution unit (FODA)


Quantity 1

•

Front cover

1

•

Mounting bracket

2

•

Cable tie bracket

1

•

M4 x 12 screws

6

•

Spring washers

6

•

M5 screws

2

•

M6 self-locking screws for wall mounting

4

•

Clamps

2

Table 32

Flexi Fiber Optical Distribution unit (FODA) delivery content

Figure 248 FODA delivery contents

230


DN09142359


22.20

Contents of the Flexi System External Alarm Module (FSEB) Description

Product code

Quantity

Flexi System External Alarm Module (FSEB):

471424A

1

•

D37 Cable Assembly

1

•

Cable tie, PER31

3

Table 33

Flexi System External Alarm Module (FSEB) delivery contents

3x

DN70274122

Figure 249 Delivery contents of the FSEB

DN09142359

Id:0900d805808557ca Confidential

231


22.21

Contents of the GPS hardware deliveries GPS hardware deliveries are presented as follows: • •

Table 34 GPS Mounting Kit (FYMA) delivery content (always needed) Table 35 GPS Antenna Kit (FYGA) delivery content and Table 36 GPS GLONASS Receiver Antenna (FYGB) delivery content (one of the two needed)

g

GPS GLONASS Receiver Antenna (FYGB) can be only used with the System Module variant FSMF. •

Table 37 GPS cable deliveries (FYHA/FYHB/FTSE/FTSH) (choose one according to your System Module variant and cable length required) Contents of the Flexi GPS Surge Protection Kit (FYEA) delivery (in case surge protection is required)

•

Description GPS Mounting Kit (FYMA)

471605A

Quantity 1

•

Fixing bands

2

•

Screws for fixing bands

2

•

Cable ties

2

Table 34

GPS Mounting Kit (FYMA) delivery content

Description GPS Antenna Kit (FYGA) Table 35

GNSS Antenna Kit (FYGB) Table 36


Quantity 1

GPS Antenna Kit (FYGA) delivery content

Description


Quantity 1

GPS GLONASS Receiver Antenna (FYGB) delivery content

Description

Product code

Quantity

GPS Cable, 30 m (98.4 ft.) (FYHA) 471606A

1

GPS Cable, 100 m (328 ft.) (FYHB)

471653A

1

GPS Cable, 30 m (98.4 ft.) (FTSE) 472510A

1

Table 37

232

Product code

GPS cable deliveries (FYHA/FYHB/FTSE/FTSH)

Id:0900d80580a2ac0d Confidential

DN09142359


Description

Product code

GPS Cable, 100 m (328 ft.) (FTSH) 472577A Table 37

Quantity 1

GPS cable deliveries (FYHA/FYHB/FTSE/FTSH) (Cont.)

For Flexi GPS Surge Protection Kit (FYEA) delivery contents, see Contents of the Flexi GPS Surge Protection Kit (FYEA) delivery. GPS hardware items are shown in figure Figure 250 GPS hardware.

FTSE

FTSH

FYGA/B

FYHA

FYHB FYMA

Figure 250 GPS hardware

DN09142359

Id:0900d80580a2ac0d Confidential

233


22.22

Contents of the Flexi GPS Surge Protection Kit (FYEA) delivery The Flexi GPS Surge Protection Kit (FYEA) delivery contains the following items: Description Flexi GPS Surge Protection Kit (FYEA)


Quantity 1

•

Grounding cable

1

•

M5 x 16 screw

4

Table 38

Flexi GPS Surge Protection Kit (FYEA) delivery content

Figure 251 FYEA delivery contents

234

Id:0900d805809d649a Confidential

DN09142359


22.23

Contents of the Flexi System Alarm Cable (FSAA) delivery Description

Product code

Quantity

Flexi System Alarm Cable (FSAA)

471628A

1

•

D37 cable assembly 15 m (49.2 ft.)

Table 39

DN09142359

1

Flexi System Alarm Cable (FSAA)


235


22.24

Contents of the GPS Box (FYGD) delivery The GPS Box (FYGD) delivery contains the following items: Description GPS Box (FYGD)


Quantity 1

•

HDMI Sync cable, 0.6 m (2 ft.)

1

•

Screws for fixing the FYGD

3

Table 40

GPS Box (FYGD) delivery content

Figure 252 GPS Box (FYGD) delivery contents

236


DN09142359


22.25

Contents of the Outdoor Side Kit (OSKA) delivery The table below presents the delivery contents of Outdoor Side Kit (OSKA). Object name

Quantity

Side wall plate

1

Wall bracket

2

Connection pin

12

Screw M5x8 TX

6

Star washer (M5)

6

Screw M6x20 TX

6

Flat washer (M6)

6

Star washer (M6)

6

Bolt M8x20 Hex head

10

Flat washer (M8)

2

Earth cable (M8)

1

Table 41

DN09142359

Delivery contents of the outdoor side kit (OSKA)

Id:0900d805809d65ac Confidential

237


22.26

Contents of the IDC_ Roof kit (IRSA) delivery The table below presents the delivery contents of IDC_ Roof Kit (IRSA). Item

Pieces

Adapter plate

1

Support rail

4

Mounting rail

2

Mask side

2

Mask front)

1

Mask upper

1

Connection pins

4

Hex nut M8

4

Washer M8

4

Torx screw M5x10)

6

1.6 earth cable (M8)

1

Table 42

238

IDC_ Roof Kit (IRSA) delivery contents

Id:0900d805809d65b2 Confidential

DN09142359


Appendix Installation tools and torque values

23 Appendix Installation tools and torque values 23.1

BTS installation tools and equipment This section lists the installation tools and equipment. Installation tools Allen key: 8 mm (0.31 in.) ESD wrist strap and cable TORX screwdriver set: T10, T20, T25 Screwdriver set: Phillips 0 , 1, 2 and flathead Wrench 13 mm (0.51 in.) Folding knife Monkey wrench Side cutters Scissors Crimping tool for 16 mm² (6 AWG) grounding cable Torque wrench for antenna cables Lint-free swab or wipe and 99% alcohol for cleaning optical connectors Cable ties for routing cables Tape measure Flashlight, pocket lamp or torch Hammer drill Marker pen or comparable tool Pliers Saw Lubricant for cables

Table 43

DN09142359

Tools for installation

Id:0900d805809a3e09 Confidential

239


23.2

Torque values Nokia Siemens Networks strongly recommends that you tighten to the following torque values. These values assume the use of a lubricated bolt or fastener. Use these values unless stated otherwise. Bolt/Screw Type

DIN

Size

Torque

TORX head screw cylinder head

7985 F1-60

M3

0.7 - 1.0 Nm


7985 F1-60


7985 F1-60


7985 F1-60

Hexagon head screw (cabinet fixing)

933-12-70

Allen screw

912-A2-70

(0.5 - 0.7 ft-lb) M4

1.2 - 1.6 Nm (0.9 - 1.2 ft-lb)

M5

2.0 - 2.5 Nm (1.5 - 1.8 ft-lb)

M8

10.0 Nm (7.4 ft-lb)

M12

49.0 Nm (36.1 ft-lb)

M8

8.0 - 10.0 Nm (5.9 - 7.4 ft-lb)

Nut

934 A2

M5

3.7 Nm (2.7 ft-lb)

Nut (cabinet fixing)

934 A2

M12

49 Nm (36.1 ft-lb)

FPKA screw

933

M8x20

20 Nm (14.8 ft-lb)

Fan fixing screws, plastic

-NA-

M4

0.7 Nm

Fan fixing screws, metal -NA-

(0.5 ft-lb) M4

1.2 Nm (0.9 ft-lb)

Table 44

240

Torque values for the BTS

Id:0900d80580857aee Confidential

DN09142359

267663760-FPFC.pdf

Recommend Documents