About this handbook................................5 Symbols glossary......................................5 Parts and accessories..............................6
Arming the alarm.....................................42 Disarming the alarm................................43
Steering wheel Quick start
Adjusting the steering wheel.................44 Audio control...........................................44 Voice control............................................45
Adjusting the pedals...............................46
Wipers and washers
Principle of operation..............................23 Fastening the seat belts........................26 Seat belt height adjustment..................26 Seat belt reminder...................................27 Using seat belts during pregnancy......27 Disabling the passenger airbag............27
Windscreen wipers.................................47 Autowipers...............................................47 Windscreen washers.............................48 Rear window wiper and washers.........48 Adjusting the windscreen washer jets.........................................................49 Headlamp washers................................49 Checking the wiper blades...................50 Changing the wiper blades...................50
Keys and remote controls
Lighting
General information on radio frequencies..........................................29 Programming the remote control........29 Changing the remote control battery...................................................30
Lighting control.........................................51 Autolamps................................................52 Front fog lamps.......................................52 Rear fog lamps........................................52 Adjusting the headlamps.......................52 Headlamp levelling..................................53 Hazard warning flashers........................54 Adaptive front lighting system (AFS)......................................................55 Direction indicators.................................56 Interior lamps...........................................57 Removing a headlamp...........................58 Removing a rear lamp............................59 Changing a bulb......................................60 Bulb specification chart..........................70
Occupant protection
Locks Locking and unlocking...........................33 Keyless entry...........................................37 Global opening and closing...................39
Engine immobiliser Principle of operation..............................41 Coded keys..............................................41 Arming the engine immobiliser..............41 Disarming the engine immobiliser.........41
1
Table of contents Ashtray......................................................111 Auxiliary power sockets........................112 Cup holders.............................................112 Glove box................................................113 Centre console.......................................113 Storage compartments........................114 Rear seat armrest..................................115 Glasses holder........................................115 Toll reader................................................115 CD changer.............................................115 Auxiliary input (AUX IN) socket.............115 USB port..................................................116
Windows and mirrors Electric windows......................................71 Exterior mirrors........................................72 Electric exterior mirrors..........................73 Interior mirror............................................73 Auto-dimming mirror..............................74
Instruments Gauges.....................................................75 Warning lamps and indicators...............78 Audible warnings and indicators..........80
Information displays Starting the engine
General information................................82 Trip computer..........................................85 Personalised settings.............................87 Information messages...........................89
General information...............................117 Ignition switch..........................................117 Steering wheel lock...............................118 Starting a petrol engine.........................118 Starting a petrol engine - E85..............119 Starting a diesel engine........................120 Keyless starting......................................121 Diesel particulate filter (DPF)................122 Switching off the engine.......................123 Engine heater.........................................123
Climate control Principle of operation..............................95 Air vents....................................................95 Manual climate control...........................95 Automatic climate control.....................98 Heated windows and mirrors..............100 Auxiliary heater.......................................101 Electric sunroof......................................102
Seats Sitting in the correct position...............105 Manual seats..........................................105 Electric seats..........................................107 Head restraints......................................109 Rear seats..............................................109 Heated seats..........................................110
Convenience features Sun blinds.................................................111 Instrument lighting dimmer...................111 Cigar lighter..............................................111
Table of contents Automatic transmission........................130
Emergency equipment
Brakes
First aid kit...............................................154 Warning triangle.....................................154
Principle of operation............................133 Hints on driving with ABS.....................133 Parking brake.........................................133
Status after a collision
Stability control
Fuel cut-off switch.................................155 Inspecting safety system components.......................................155
Principle of operation............................134 Using stability control............................134
Fuses
Parking aid
Fuse box locations................................156 Changing a fuse....................................156 Fuse specification chart........................157
Principle of operation............................135 Using the parking aid............................135
Vehicle recovery Cruise control
Towing points.........................................163 Towing the vehicle on four wheels.....164
Principle of operation............................137 Using cruise control...............................137
General information..............................139 Luggage covers....................................139 Rear under floor storage......................140 Cargo nets..............................................140 Roof racks and load carriers................141
Towing Towing a trailer.......................................144 Detachable tow ball..............................144
Convertible top Opening the convertible top................147 Closing the convertible top..................149
Driving hints Running-in..............................................153 Driving through water...........................153
Telephone General information..............................212 Telephone setup...................................212 Bluetooth setup.....................................213 Telephone controls...............................214 Using the telephone - Vehicles Without: Navigation System.............................214 Using the telephone - Vehicles With: Navigation System.............................217
Voice control
Cleaning the exterior............................184 Cleaning the interior..............................184 Repairing minor paint damage............185
Principle of operation............................219 Using voice control...............................219 Audio unit commands.........................220 Telephone commands.........................231 Navigation system commands..........235 Climate control commands................235
Vehicle battery
Connectivity
Using booster cables............................186 Changing the vehicle battery...............187
General information..............................238 Connecting an external device..........239 Using a USB device..............................239 Using an iPod........................................242
Vehicle care
Wheels and tyres General information..............................188 Changing a road wheel........................188 Tyre care.................................................192 Tyre repair kit..........................................193 Using winter tyres..................................197 Using snow chains................................198 Tyre pressure monitoring system.......198 Technical specifications........................199
Appendices Type approvals......................................246 Type approvals......................................252 Type approvals......................................252 Electromagnetic compatibility............252
Vehicle identification Vehicle identification plate...................204 Vehicle identification number (VIN).....204
4
Introduction Assessment carried out by Allergy UK indicate that an individual’s exposure can be reduced but this does not mean that an individual’s allergic symptoms will necessarily diminish. Allergy UK’s opinion applies only to the products and allergens stated.
ABOUT THIS HANDBOOK Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this handbook. The more that you know about it, the greater the safety and pleasure you will get from driving it.
The British Allergy Foundation’s Seal of Approval is a European Community registered trademark.
Note: This handbook describes product features and options available throughout the range, sometimes even before they are generally available. It may describe options not fitted to your vehicle.
For more info. Contact TÜV at www.tuv.com or the British Allergy Foundation (Charity Reg.No.1094231) at www.allergyuk.org or ring their English only Helpline at UK 44-(0)-1322-619898.
Note: Always use and operate your vehicle in line with all applicable laws and regulations.
SYMBOLS GLOSSARY
Note: Pass on this handbook when selling your vehicle. It is an integral part of the vehicle.
Symbols in this handbook
This vehicle has received both the endorsement of TÜV, the accredited international testing organisation, and been awarded the British Allergy Foundation’s Seal of Approval’ for its allergy-friendly properties.
WARNING You risk death or serious injury to yourself and others if you do not follow the instructions highlighted by the warning symbol.
All materials used in the manufacture of the interior of this vehicle meet strict requirements of the TÜV TOXPROOF Criteria Catalogue for Vehicle Interiors by TÜV Produkt and Umwelt GmbH and are designed to minimize the risk of allergic reactions.
CAUTION You risk damaging your vehicle if you do not follow the instructions highlighted by the caution symbol.
Symbols on your vehicle
Additionally an efficient pollen filter protects the passengers against allergen particles in the outdoor air. The British Allergy Foundation (BAF) considers that these products may, in proper use, reduce exposure to chromium, nickel, latex, grass pollen and other sensitizing substances and volatile organic compounds.
When you see these symbols, read and follow the relevant instructions in this handbook before touching or attempting adjustment of any kind.
5
Introduction PARTS AND ACCESSORIES Now you can be sure that your Ford parts are Ford parts Your Ford has been built to the highest standards using high quality Ford Original Parts. As a result, you can enjoy driving it for many years. Should the unexpected occur and a major part needs replacing, we recommend that you accept nothing less than Ford Original Parts. The use of Ford Original Parts ensures that your vehicle is repaired to its pre-accident condition and maintains its maximum residual value. Ford Original Parts match Ford's stringent safety requirements and high standards of fit, finish and reliability. Quite simply, they represent the best overall repair value, including parts and labour costs.
E89927
Bumper and radiator grille
Now it is easier to tell if you have really been given Ford Original Parts. The Ford logo is clearly visible on the following parts if they are Ford Original Parts. If your vehicle has to be repaired, look for the clearly visible Ford branding and make sure that only Ford Original Parts have been used.
• •
Radiator grille Front and rear bumper
Look for the Ford logo on the following parts Sheet metal • • • •
Bonnet Wings Doors Luggage compartment lid or tailgate
Heated rear window switch. See Climate control (page 95).
M
Start button. See Keyless starting (page 121).
N
Heated windscreen switch. See Climate control (page 95).
O
Convertible top switch (convertible). See Convertible top (page 147).
O
Stability control (ESP) switch (Focus ST and Focus RS). See Using stability control (page 134).
P
Heated front seat switch. See Seats (page 105).
Q
Ignition switch. See Starting the engine (page 117).
R
Steering wheel adjustment.
S
Cruise control switches. See Cruise control (page 137).
T
Audio controls.
U
Instrument lighting dimmer. See Convenience features (page 111). Unlocking the vehicle
Keyless entry
E78276
Passive locking and unlocking requires a valid passive key to be located within one of the three external detection ranges.
E78278
Pull a door handle to unlock all the doors and the luggage compartment lid and disarm the alarm.
10
Quick start Adjusting the steering wheel
Locking the vehicle
WARNING Never adjust the steering wheel when the vehicle is moving.
2 2
E87384
1 E95178
E87435
Locking buttons are located on each of the front doors and the luggage compartment lid. See Keyless entry (page 37).
Keyless starting
3 E95179
WARNING Make sure that you fully engage the locking lever when returning it to its original position. E85766
Press the start button. See Keyless starting (page 121).
11
Quick start Direction indicators Electric folding mirrors
E71098
Note: Tap the lever up or down to make the direction indicators flash only three times.
E78811
Press the switch to fold or unfold the mirrors.
See Direction indicators (page 56).
Autowipers
See Electric exterior mirrors (page 73).
A
B
Autolamps
C
E71013
A
Low sensitivity
B
On
C
High sensitivity
See Windscreen wipers (page 47).
E73840
The headlamps will come on and go off automatically depending on the ambient light. See Lighting control (page 51).
12
Quick start Manual climate control
Automatic climate control
Defrosting and demisting the windscreen
A
E
B
D
C
E78730
A
Windscreen defrosting/demisting
E71382 Heating the interior quickly
B
Toggle mono mode on and off
C
Air conditioning OFF
D
Recirculated air
E
Air conditioning ON
Recommended settings: AUTO, 22ºC See Automatic climate control (page 98).
E71377
Manual transmission
Cooling the interior quickly
Selecting reverse gear On some vehicles it is necessary to raise the collar whilst selecting reverse gear.
E71381 See Manual climate control (page 95).
E99067
See Transmission (page 130).
13
Quick start Returning the seatback to the seating position - 3-door
Automatic transmission Note: When the engine is started, the brake pedal and the selector lever button must be depressed before the selector lever can be moved from the park position P.
3
2
See Transmission (page 130).
Manual seats Folding the seatback forwards 3-door
1 E78818
WARNING Do not place any objects behind the seatback which could prevent the engagement of the seat lock. 1.
2. Pull the locking lever 2 to release the seatback. 3. Unfold the seatback 3 until it locks with a distinct click.
E78817
1.
Slide the seat backwards 1 to the end stop (memory position) or desired forward seating position.
Pull the locking lever 1 to release the seatback.
Note: Do not hold the locking lever. 2. Push the seatback forwards to lock it in the folded position 2. 3. Continue to push the seatback to slide the seat forwards 3.
14
Quick start 8/10 way Recaro seats - Focus ST
Recaro leather seat - Focus ST
E78816
To adjust the length of the seat cushion, press the locking handle underneath the cushion extension and slide the extension forwards or rearwards. See Manual seats (page 105).
Fuel filler flap WARNINGS Take care when refuelling to avoid spilling any residual fuel from the fuel pipe nozzle.
E78815
Each pull or press on the lever will raise or lower the cushion angle by a small amount.
We recommend that you wait at least 10 seconds before removing the fuel pipe nozzle to allow any residual fuel to drain into the fuel tank.
E86613
15
Quick start Press the flap to open it. Open the flap fully until it engages. When you insert the fuel pipe nozzle, a spring loaded inhibitor will open if the correct size nozzle is detected. This will prevent filling up with the wrong fuel.
E107539
Insert the filler up to the first notch on the nozzle, and keep it in position on the fuel filler opening. See Fuel filler flap (page 125).
16
Child safety Only child restraints certified to ECE-R44.03 (or later) have been tested and approved for use in your vehicle. A choice of these are available from your Dealer.
CHILD SEATS
Child restraints for different mass groups Use the correct child restraint as follows: Baby safety seat
E68916
WARNINGS Secure children that are less than 150 centimetres tall or less than 12 years of age in a suitable, approved child restraint, in the rear seat. Original text according to ECE R94.01: Extreme Hazard! Do not use a rearward facing child restraint on a seat protected by an air bag in front of it!
E68918
Secure children that weigh less than 13 kilograms in a rearward facing baby safety seat (Group 0+) in the rear seat.
Read and follow the manufacturer’s instructions when you are fitting a child restraint. Do not modify child restraints in any way. Do not hold a child on your lap when the vehicle is moving. Do not leave unattended children in your vehicle. If your vehicle has been involved in an accident, have the child restraints checked by properly trained technicians. Note: Mandatory use of child restraints varies from country to country.
17
Child safety Child safety seat
Secure children that weigh between 13 and 18 kilograms in a child safety seat (Group 1) in the rear seat.
E68920
CHILD SEAT POSITIONING Child seat positions WARNINGS For rearward facing child restraints in the front passenger seat, the front passenger airbag must be switched OFF. When using a child seat with a seat belt, make sure that the seat belt is not slack or twisted. Note: For rearward facing child restraints in the front passenger seat, the seat must be adjusted to the rearmost position with the seatback fully upright. Seating positions
Front passenger airbag ON (All except Focus RS)
Mass group categories 0
0+
I
II
III
Up to 10 kg
Up to 13 kg
9-18 kg
15-25 kg
22-36 kg
Baby safety seat
Baby safety seat
Child safety seat
Booster seat or cushion
Booster seat or cushion
X
X
18
1
U
U
1
1
U
Child safety Seating positions
Mass group categories 0
0+
I
II
III
Up to 10 kg
Up to 13 kg
9-18 kg
15-25 kg
22-36 kg
Baby safety seat
Baby safety seat
Child safety seat
Booster seat or cushion
Booster seat or cushion
Front passenger airbag OFF (All except Focus RS)
U
U
U
U
U
Front passenger airbag ON (Focus RS)
X
X
L
L
L
Front passenger airbag OFF (Focus RS)
L
L
L
L
L
Rear seats
U
U
U
U
U
L Suitable only for the following child restraints: Roemer Baby-Safe (E1-04301146), Roemer Baby-Safe Plus (E1-04301146), Roemer Duo (E1-04301133), Roemer Duo Plus (E1-04301133) and Roemer KID (E1-04301148). However, we recommend that you secure children in a government approved child restraint, in the rear seat. U Suitable for universal category child restraints approved for use in this mass group. X Not suitable for children in this mass group. 1
U Suitable for universal category child restraints approved for use in this mass group. However, we recommend that you secure children in a government approved child restraint, in the rear seat.
19
Child safety Booster seat (Group 2)
BOOSTER CUSHIONS WARNINGS Do not install a booster seat or a booster cushion with only the lap strap of the seat belt. Do not install a booster seat or a booster cushion with a seat belt that is slack or twisted. Do not put the seat belt under your child’s arm or behind its back. Do not use pillows, books or towels to boost your child’s height. Make sure that your children sit in an upright position.
E70710
We recommend that you use a booster seat that combines a cushion with a backrest instead of a booster cushion only. The raised seating position will allow you to position the shoulder strap of the adult seat belt over the centre of your child’s shoulder and the lap strap tightly across its hips.
Secure children that weigh more than 15 kilograms but are less than 150 centimetres tall in a booster seat or a booster cushion. CAUTION When using a child seat on a rear seat, make sure that the child seat rests tightly against the vehicle seat. It may be necessary to lift or remove the head restraint. See Head restraints (page 109).
Booster cushion (Group 3)
E68924
20
Child safety ISOFIX ANCHOR POINTS
Attaching a child restraint with a top tether
E68945
E78828
WARNING
WARNING
Use only ISOFIX child seats we recommend.
Do not attach a tether strap to anything other than the correct tether anchor point.
You can fit ISOFIX child restraints using the ISOFIX anchor points.
Route the tether strap to the anchor point. Tighten the tether strap to the manufacturer's instructions.
The ISOFIX system comprises of two rigid attachment arms on the child restraint that attach to anchor points on the rear seats, where the cushion and backrest meet. Tether anchor points may also be fitted.
All except convertible WARNING Use an anti-rotation device when using the ISOFIX system. We recommend that you use a top tether or a support leg.
21
Child safety CHILD SAFETY LOCKS
E78298
WARNING When the child safety lock is activated, the door can only be opened from outside. Turn the key in the rear door in the direction of the arrow to activate the lock. To deactivate the lock turn the key in opposite direction to the arrow.
22
Occupant protection PRINCIPLE OF OPERATION
WARNINGS Repairs to either of the front seat covers, the sensors attached to the seats as well as to the roof lining should only be carried out by properly trained technicians. Injuries may result if the side airbags are triggered inadvertently.
Airbags WARNING Do not modify the front of the vehicle in any way as this can adversely affect airbag deployment.
Do not block, obstruct or cover the airbag because it may prevent proper deployment. Do not poke any sharp objects into the areas where airbags are fitted. This could damage the airbags.
Note: A loud bang will be heard when an airbag deploys and it is normal to see a cloud of harmless powdery residue. The airbag system comprises the following: • • • • • • • • • •
Do not use any accessory seat covers that are not specifically designed for seats with side airbags. These seat covers must be fitted by properly trained technicians.
single-stage inflatable nylon bags (airbags) with gas generators side airbags curtain airbags seat belt pretensioners a seat belt reminder crash sensors. a warning lamp in the instrument panel. an airbag deactivation switch an airbag deactivation indicator in the instrument panel an electronic control and diagnostic unit.
E66553
WARNING Always wear the seat belt and keep sufficient distance between the driver and the steering wheel. Only when the seat belt is used properly, can it hold the body in a position which allows the airbag to achieve its optimum effect. There is a risk of injury when the airbag deploys. The seat and back must be set correctly for the airbags to be optimally effective. See Sitting in the correct position (page 105).
E72330
23
Occupant protection This is the ideal seating position for the driver and front passenger and helps reduce the risk of injury from sitting too close to an inflating airbag.
E78294
WARNINGS Repairs to the steering wheel, steering column and airbag system should be carried out by properly trained technicians.
E74302 The front airbags activate during significant collisions which are either frontal or up to 30 degrees from the left or the right. The airbags inflate within a few thousandths of a second. They will deflate on contact with the front occupants thus cushioning forward body movement.
Always keep the areas in front of the airbags free. Never affix anything to or over these areas. These areas should only be wiped with a damp cloth, never with a wet cloth. Side air bags
E72326
E72658
During minor collisions as well as overturns and rear or side collisions, the front airbag system will not be activated.
24
Occupant protection Seat belts
A label on the seatback indicates that side airbags are fitted. The side airbags are fitted on the side of the seatbacks of the front seats. In case of a severe lateral collision, the airbag on the side affected by the collision will be inflated.
WARNINGS Use seat belts at all times. Never use a seat belt for more than one person.
The airbag will inflate between the door panel and occupant. Once the occupant’s body contacts the airbag, the propellant escapes, thereby cushioning the impact.
Avoid wearing thick clothing.
The side airbags are not activated upon minor lateral collisions nor upon front or rear impacts.
The seat belts should fit tightly around the body.
Curtain air bags
Seat belt pretensioner
E75004
E72333
WARNING
Moulded badges in the A- and B-pillar trims indicate that curtain air bags are fitted. The curtain airbags are fitted over the front and rear side windows inside the roof lining. In case of a severe lateral collision, the air bag on the side affected by the collision will be inflated.
The belt pretensioners must not be removed. If the pretensioners are deployed during an accident, they must be replaced. Have the pretensioners serviced and disposed of by specially trained personnel only.
The curtain air bags are not activated upon minor lateral collisions nor upon front or rear impacts.
25
Occupant protection The restraint system, with belt pretensioners in the front seats, helps to reduce the risk of serious injury in a major frontal impact. During a serious crash the seat belts are pretensioned to help reduce slack in the belt. The safety belt pretensioner is a device which removes excess webbing from the safety belt system. When the safety belt pretensioner deploys, webbing from the lap and shoulder belt is tightened. The belt pretensioner is not triggered in any side, rear or minor frontal collisions. E85817
FASTENING THE SEAT BELTS
Pull the belt out steadily. It may lock if you pull it sharply or if the vehicle is on a slope. Press the red button on the buckle to release the belt. Let it retract completely and smoothly.
WARNING Insert the tongue into the buckle until you hear a distinct click. You have not fastened the seat belt properly if you do not hear a click.
SEAT BELT HEIGHT ADJUSTMENT
E74124 E87511
Note: Lifting the slider slightly while pressing the locking button makes it easier to release the locking mechanism. To raise or lower, press the locking button on the adjuster and move as necessary.
26
Occupant protection Position the lap strap comfortably across your hips and low beneath your pregnant abdomen. Position the shoulder strap between your breasts, above and to the side of your pregnant abdomen.
SEAT BELT REMINDER WARNING The occupant protection system will only provide optimum protection when you use the seat belt properly.
DISABLING THE PASSENGER AIRBAG
The seat belt reminder warning lamp illuminates and an audible warning will sound if a seat belt has not been fastened and the vehicle exceeds a relatively low speed. It will also illuminate if a seat belt is unfastened when the vehicle is moving. The audible warning will go off after approximately five minutes but the seat belt reminder warning lamp will remain on until the seat belt has been fastened.
WARNING Make sure that the passenger airbag is disabled when using a rearward facing child restraint on the front passenger seat.
Deactivating the seat belt reminder See your dealer.
USING SEAT BELTS DURING PREGNANCY E71313
Fitting the passenger airbag deactivation switch WARNING If you need to fit a child restraint on a seat protected by an operational airbag in front of it, have a passenger airbag deactivation switch fitted. Ask your dealer for further information.
E68587
WARNING
Note: The key switch is located in the glove compartment with an airbag deactivation lamp in the instrument panel.
Position the seat belt correctly for your safety and that of your unborn child. Do not use only the lap strap or the shoulder strap.
27
Occupant protection If the airbag warning lamp illuminates or flashes when you are driving, this indicates a malfunction. See Warning lamps and indicators (page 78). Remove the child restraint and have the system checked immediately.
Disabling the passenger airbag
A
B
E71312
A
Disabled
B
Enabled
Turn the switch to position A. When you switch the ignition on, check that the passenger airbag deactivation warning lamp illuminates.
Enabling the passenger airbag WARNING Make sure that the passenger airbag is enabled when you are not using a child restraint on the front passenger seat. Turn the switch to position B.
28
Keys and remote controls •
GENERALINFORMATIONON RADIO FREQUENCIES
•
CAUTION The radio frequency used by your remote control can also be used by other short distance radio transmissions (e.g. amateur radios, medical equipment, wireless headphones, remote controls and alarm systems). If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key.
To programme new remote controls turn the ignition key to position II four times within six seconds. Turn the ignition to position 0. A tone sounds to indicate that it is now possible to programme the remote controls for ten seconds.
Note: You could unlock the doors if you press the buttons on the remote control unintentionally. The operating range between your remote control and your vehicle varies depending on the environment.
E78254
•
PROGRAMMING THE REMOTE CONTROL You can programme a maximum of eight remote controls to use with your vehicle (including any supplied with your vehicle). The remote controls must remain inside the vehicle during the programming procedure. Fasten the front seat belts and close all doors to ensure that conflicting chimes do not sound during programming.
•
Press any button on a new remote control. A tone will sound as confirmation. Repeat this last step for all your remote controls, including your original. Do not remove the key from the ignition when pressing the button on this remote control. Switch the ignition back on (position II) or wait for ten seconds without programming another remote control to end the key programming. Only the remote controls which you have just programmed are now able to lock and unlock the vehicle.
Reprogramming the unlocking function Note: When you press the unlock button either all the doors are unlocked or only the driver’s door and the luggage compartment lid are unlocked. Pressing the unlock button again unlocks all the doors.
E78253
29
Keys and remote controls Press and hold the unlock and lock buttons on the remote key simultaneously for at least four seconds with the ignition off. The direction indicators will flash twice to confirm the change.
2. Twist the screwdriver in the position shown to start separating the two halves of the remote control.
To return to the original unlocking function, repeat the process.
CHANGING THE REMOTE CONTROL BATTERY Make sure that you dispose of old batteries in an E107998 environmentally friendly way. Seek advice from your local authority regarding recycling.
3 E74385 3. Twist the screwdriver in the position shown to separate the two halves of the remote control.
Remote control with a folding key blade
CAUTION Do not touch the battery contacts or the printed circuit board with the screwdriver. 4. Carefully prise out the battery with the screwdriver. 5. Install a new battery (3V CR 2032) with the + facing downwards. 6. Assemble the two halves of the remote control. 7. Install the key blade.
1 E74383 1.
Insert a screwdriver as far as possible into the slot on the side of the remote control, push it towards the key blade and remove the key blade.
2 E74384
30
Keys and remote controls Remote control without a folding key blade
Type 2
Type 1
2 1
E78284
1.
Slide the release slider in the direction of the arrow. 2. Remove the key blade.
E74386 1.
Insert a screwdriver into the recess on the back of the key and remove the key blade. 2. Release the retaining clips with the screwdriver and separate the two halves of the remote control. CAUTION Do not touch the battery contacts or the printed circuit board with the screwdriver.
3 3. Carefully prise out the battery with the screwdriver. 4. Install a new battery (3V CR 2032) with the + facing upwards. 5. Assemble the two halves of the remote control. 6. Install the key blade.
E105064
3. Twist the screwdriver in the position shown to separate the two halves of the remote control. CAUTION Do not touch the battery contacts or the printed circuit board with the screwdriver.
31
Keys and remote controls 4. Carefully prise out the battery with the screwdriver. 5. Install a new battery (3V CR 2032) with the + facing downwards. 6. Assemble the two halves of the remote control. 7. Install the key blade.
32
Locks Locking and unlocking from the inside
LOCKING AND UNLOCKING Doors Locking and unlocking from the outside
A
Left-hand drive
E72194
B
Note: On vehicles without remote control, all doors can also be locked using the locking button on the front passenger’s door. E78260
When inside the vehicle, all doors can be locked with the locking button A on the driver’s door and unlocked using the door handle B. To lock the front passenger’s door and the rear doors individually, depress the locking button and close the door when leaving the vehicle.
Right-hand drive
E78261
Note: Only vehicles without remote control are equipped with a lock cylinder in the passenger’s door. All doors can be locked and unlocked from the outside with the key at the driver’s door. On vehicles without remote control, they can also be locked and unlocked at the front passenger’s door.
33
Locks Tailgate
Central and double locking
Opening the tailgate
Left-hand drive
E78264
Right-hand drive
E78262
Note: If there is a cut in the power supply e.g. the battery is disconnected, it is not possible to open the tailgate. To open the tailgate, the vehicle must first be unlocked with the key or remote control.
E78265
To open the luggage compartment, press the switch. The driver’s door must be unlocked.
WARNING Double locking should not be activated when persons are inside the vehicle.
Closing the tailgate
Note: Only vehicles without remote control are equipped with a lock cylinder in the passenger’s door. The central locking system can be activated from the driver’s door. It operates only when the front doors are closed. It is activated from the outside with the key or remote control, or from inside by depressing the locking button on the driver’s door handle.
E78263
A recessed grip is incorporated inside the tailgate to facilitate closing.
34
Locks On vehicles without remote control, it can also be activated from outside with the key at the passenger’s door or using the locking button on that door.
E78267
WARNING If a failure occurs in the vehicle’s electrical system the driver’s door can still be individually unlocked with the key. With the remote control: Press the unlock button once.
E72198
Double locking is an additional theft protection feature which prevents the vehicle’s doors being opened from inside the vehicle. Double locking is possible only if the front doors are closed.
One long flash of the direction indicators confirms that all the doors, the tailgate and the fuel filler flap have been unlocked and that the anti-theft alarm system has been disarmed.
Unlocking the vehicle Automatic relocking To prevent the vehicle being left unlocked inadvertently, central locking and the anti-theft alarm system will be reactivated automatically 45 seconds after the unlock button is pressed if the following occurs during this period: • • •
No door is opened. The luggage compartment is not opened. The ignition is not switched on.
Unlocking the tailgate
E78266
With the key: Turn the key in the driver’s or front passenger’s door to position 1. E78268
35
Locks Left-hand drive
To unlock only the tailgate when the vehicle is locked, press the unlock button twice within three seconds. Locking the vehicle
E78271
Right-hand drive
E78272
With the key: Turn the key in the driver’s door to position 2 twice within three seconds. E78269
CAUTION
To activate central locking and arm the anti-theft alarm system:
Convertible only - Always double lock your vehicle when the convertible top is open.
With the key: Turn the key in the driver’s or front passenger’s door to position 2.
E78270
E78270
With the remote control: • All except convertible - Press the lock button twice within three seconds. • Convertible only - Press the lock button once.
With the remote control: Press the lock button once. On vehicles without double locking, the direction indicators will flash twice as confirmation. Double locking the vehicle
The direction indicators will flash twice as confirmation.
Note:
36
Locks Passive locking and unlocking requires a valid passive key to be located within one of the three external detection ranges. These are located approximately one and a half metres from the driver and front passenger door handles and the luggage compartment lid.
KEYLESS ENTRY General information WARNING The keyless entry system may not function if the key is close to metal objects or electronic devices such as mobile phones.
Passive key The vehicle can be locked and unlocked with the passive key. The passive key can also be used as a remote control. See Locking and unlocking (page 33).
Note: If the door handles are pulled repeatedly during a short period of time without the presence of a valid passive key, the system will become inoperable for 30 seconds.
Locking the vehicle WARNING
The passive entry system will not function if: • The passive key frequencies are jammed. • The passive key battery is flat.
The vehicle does not lock itself automatically. If no locking button is pressed, the vehicle will remain unlocked.
Note: If the passive entry system does not function, you will need to use the key blade to lock and unlock your vehicle. The keyless system allows the driver to operate the vehicle without the use of a key or remote control.
E87384
E78276
37
Locks Unlocking the vehicle Note: If the vehicle remains locked for longer than three days, the key free system will enter an energy-saving mode. This is to reduce the discharge of the vehicle battery. When the vehicle is unlocked while in this mode, the reaction time of the system may be a little longer than normal. Unlocking the vehicle once will deactivate the energy-saving mode. E87435
Locking buttons are located on each of the front doors and the luggage compartment lid. To activate central locking and arm the alarm: • Press a locking button once. To activate double locking, to arm the alarm and the interior sensors: • All except convertible - Press a locking button twice within three seconds. • Convertible only - Press a locking button once.
E78278
Pull one of the door handles or the luggage compartment lid handle.
Note: Once activated, the vehicle will remain locked for approximately three seconds. This is to allow you to pull a door handle and check if the vehicle is locked. When the delay period is over, the doors can be opened again, provided the passive key is within the respective detection range.
Note: A valid passive key must be located within the detection range of that door. One long flash of the direction indicators confirms that all the doors, the luggage compartment lid and the fuel filler flap have been unlocked and that the alarm has been disarmed.
Luggage compartment lid
Unlocking only the driver's door
Note: The luggage compartment lid cannot be closed and will pop back up if the passive key is located inside the luggage compartment.
If the unlocking function is reprogrammed so that only the driver’s door is unlocked ( See Programming the remote control (page 29). ), note the following:
Note: If a second valid passive key is located within the luggage compartment lid detection range, the luggage compartment lid can be closed.
38
Locks If the driver’s door is the first door which is opened, the other doors will remain locked. All the other doors can be unlocked from inside the vehicle by using the unlock button next to the driver’s door handle. Doors can be unlocked individually by pulling the interior door handles on those doors.
1.
Slide the release slider in the direction of the arrow and pull out the key blade with your thumb. 2. Remove the key blade and insert it into the lock.
GLOBAL OPENING AND CLOSING
If the front passenger door or one of the rear doors is the first door which is opened, all the doors and the luggage compartment lid will be unlocked.
You can also operate the electric windows with the ignition off via the global opening and global closing function.
Disabled keys
Note: Global closing will only operate if you have set the memory correctly for each window. See Electric windows (page 71).
Any keys left inside the vehicle interior when it is locked will be disabled. A disabled key cannot be used to turn the ignition on or start the engine.
Global opening
In order to use these passive keys again, they have to be enabled. To enable all your passive keys, unlock the vehicle using a passive key or the remote control unlocking function. All passive keys will then be enabled if the ignition is turned on or the vehicle is started using a valid key.
Locking and unlocking the doors with the key blade
E71955
To open all the windows, press and hold the unlock button for at least three seconds. Press either the lock or the unlock button again to stop the opening function.
2 1
E78284
39
Locks Global closing
WARNING Take care when using global closing. In an emergency, press the button on the driver’s door handle to stop.
Vehicles without the key free system WARNING Take care when using global closing. In an emergency, press a button immediately to stop.
Note: Global closing can be activated using the button on the driver’s door handle. Global opening and closing can also be activated using the buttons on the passive key. To close all the windows, press and hold the button on the driver’s door handle for at least two seconds. The anti-trap function is also active during global closing.
E71956
To close all the windows, press and hold the lock button for at least three seconds. Press any button again to stop the closing function. The anti-trap function is also active during global closing. Vehicles with the key free system
E87384
40
Engine immobiliser The indicator in the instrument cluster will come on for approximately three seconds and then go out. If the indicator stays on for one minute or flashes for approximately one minute and then repeatedly at irregular intervals, your key has not been recognised. Remove the key and try again.
PRINCIPLE OF OPERATION The engine immobiliser is a theft protection system that prevents someone from starting the engine with an incorrectly coded key.
CODED KEYS
If you are unable to start the engine with a correctly coded key, this indicates a malfunction. Have the immobiliser checked immediately.
Note: Do not shield your keys with metal objects. This may prevent the receiver from recognising your key as a valid one. Note: Have all of your remaining keys erased and recoded if you lose a key. Ask your dealer for further information. Have replacement keys recoded together with your existing keys. If you lose a key, you can obtain a replacement from your Ford Dealer. If possible, provide them with the key number from the tag provided with the original keys. You can also obtain additional keys from your Ford Dealer.
ARMING THE ENGINE IMMOBILISER The engine immobiliser is armed automatically a short time after you have switched the ignition off. The indicator in the instrument cluster will flash to confirm that the system is operating.
DISARMING THE ENGINE IMMOBILISER The engine immobiliser is disarmed automatically when you switch the ignition on with a correctly coded key.
41
Alarm This system acts as a deterrent against unauthorised intrusion by sensing any movement within the vehicle.
ARMING THE ALARM The system is armed as soon as the vehicle is locked and acts as a deterrent to unauthorised persons who attempt to open the doors, bonnet or luggage compartment, or remove the audio system.
Unauthorised entry into the vehicle’s interior will trigger the alarm in the same way as the anti-theft system. The sensors are located in the interior lamp unit.
The alarm sounds for 30 seconds if an unauthorised person opens a door, the luggage compartment or the bonnet. The hazard flasher lights will flash for five minutes.
Convertible only The interior sensors are automatically disabled if the convertible top is open. All except Britain and Ireland
Any attempt to start the engine without a valid key or to remove the audio system sounds the alarm again.
The interior sensing alarm is armed together with the double locking system.
Automatic arming delay
Britain and Ireland only
The 20 seconds arming delay begins when the bonnet, luggage compartment and all doors are closed.
The interior sensing alarm is armed together with the central locking system. To deactivate the interior sensors:
Interior sensors
Vehicles without keyless entry system
E71401
E80555
WARNING
Press the upper part of the switch next to the driver’s door handle.
This system functions correctly only if all windows and the sunroof are completely closed. In addition to this, the sensors located in the interior lamp unit must not be covered up. The system should not be activated if any persons, animals or other moving objects are inside the vehicle.
Vehicles with keyless entry system
E80556
Note: The interior sensors will not operate if the convertible top is open.
Press the lower part of the switch next to the driver’s door handle.
42
Alarm DISARMING THE ALARM The anti-theft alarm system can be deactivated at any time – even when the alarm is sounding – by unlocking the vehicle from the outside. The anti-theft alarm system for the tailgate is deactivated if the tailgate is unlocked using the button on the remote control or passive key. On vehicles with the Key Free System, it is deactivated if a passive key is located within the tailgate detection range when the tailgate is opened. After closure, the alarm is once again armed.
Britain and Ireland only If the vehicle is unlocked using the key or the spare key for the keyless entry system, a 12 second delay chime starts as soon as the driver’s door is opened. The alarm should be deactivated during this period. Vehicles without keyless entry system To deactivate the alarm, insert the key into the ignition and turn it to position II. Vehicles with keyless entry system The alarm should be deactivated in one of the following ways: • If a valid passive key is located within the vehicle interior, depress the clutch pedal (manual transmission) or brake pedal (automatic transmission), push the ignition switch in and turn it to position II. • Insert the spare key into the ignition switch, push the ignition switch in and turn it to position II. • Press the unlock button on the passive key.
43
Steering wheel ADJUSTING THE STEERING WHEEL
WARNING Make sure that you fully engage the locking lever when returning it to its original position.
WARNING Never adjust the steering wheel when the vehicle is moving.
AUDIO CONTROL Select radio, CD or cassette mode on the audio unit.
Note: Make sure that you are sitting in the correct position. See Sitting in the correct position (page 105).
The following functions can be operated with the remote control:
Volume
2 2
1 E95178
E78046
Volume up: Press the top button on the back of the remote control. Volume down: Press the bottom button on the back of the remote control.
3 E95179
44
Steering wheel Seek
• • •
In radio mode, this will locate the next pre-set radio station. In CD mode, this will select the next CD if a CD changer is fitted. In all modes to abort a traffic message during broadcasting.
Press and hold the button on the side: •
In radio mode to change the waveband.
VOICE CONTROL
E78047
Move the lever up or down: •
•
E78049
In radio mode, this will locate the next radio station up or down the frequency band. In CD mode, it will select the next or previous track.
To select or deselect voice control, press the button on the top. For further information See Voice control (page 219).
Mode
E78048
Briefly press the button on the side:
45
Pedals ADJUSTING THE PEDALS
E78045
WARNINGS Never adjust the pedals when the vehicle is moving. When a floor mat is fitted, the pedals may get caught on the mat. When using floor mats, always ensure that there is enough clearance for the pedals to move. Press the upper part of the switch to move the pedals towards the driver. Press the lower part of the switch to move the pedals away from the driver. See Sitting in the correct position (page 105).
46
Wipers and washers Automatic wiper system
WINDSCREEN WIPERS
Some models without autowipers are fitted with a speed-dependent front screen wiper system.
D C
When the vehicle is slowed to walking speed or is brought to a standstill, the wiper speed will automatically switch to the next lower wiper speed setting.
B
When the vehicle speed is increased, the wiper speed will return to the manually-chosen setting. Moving the wiper lever when the system is operating will switch off the system. If the vehicle is again slowed to walking speed or is brought to a standstill, the system is reactivated.
A E71012
A
Single wipe
AUTOWIPERS
B
Intermittent wipe or autowipers
C
Normal wipe
D
High speed wipe
CAUTIONS Do not switch autowipers on in dry weather conditions. The rain sensor is very sensitive and the wipers may operate if dirt, mist or flies hit the windscreen.
Intermittent wipe
A
Replace the wiper blades as soon as they begin to leave bands of water and smears. If you do not replace them, the rain sensor will continue to detect water on the windscreen and the wipers will operate, even though the majority of the windscreen is dry.
B
Fully defrost the windscreen in icy conditions before you switch autowipers on.
C
E71013
A
Long wipe interval
B
Intermittent wipe
C
Short wipe interval
Switch autowipers off before you enter a car wash.
47
Wipers and washers A
WARNING
B
Do not operate the washer for more than 10 seconds at a time, and never when the reservoir is empty. While the button at the end of the lever is pressed the washer will work in conjunction with the wipers. After releasing the button, the wipers operate for a short time.
C
E71013
A
Low sensitivity
B
On
C
High sensitivity
REAR WINDOW WIPER AND WASHERS Intermittent wipe
If you switch autowipers on, the wipers will not cycle until water is detected on the windscreen. The rain sensor will then continuously measure the amount of water on the windscreen and adjust the speed of the wipers automatically. Adjust the sensitivity of the rain sensor using the rotary control. With low sensitivity, the wipers will operate when the sensor detects a lot of water on the windscreen. With high sensitivity, the wipers will operate if the sensor detects a small amount of water on the windscreen.
E71017
Pull the lever towards the steering wheel.
Reverse gear wipe
WINDSCREEN WASHERS
The rear wiper will be activated automatically when selecting reverse gear if: • the rear wiper is not already switched on, • the wiper lever is in position A, B, C or D and • the front wiper is operating (when set to position B). E71016
The rear wiper will follow the front wiper interval (at intermittent or normal speed).
48
Wipers and washers Rear window washer
ADJUSTING THE WINDSCREEN WASHER JETS
E71018
WARNING Do not operate the washer for more than 10 seconds at a time, and never when the reservoir is empty. E73425
While the lever is pulled towards the steering wheel the washer will work in conjunction with the wipers.
The eye ball jets can be adjusted precisely using a pin.
Once the wash/wipe cycle is completed, the wipers will pause and then perform one more wipe to clear the windscreen.
HEADLAMP WASHERS The headlamp washers will operate with the windscreen washers when the headlamps are on.
After releasing the lever, the wipers operate for a short time.
Note: To stop the washer fluid reservoir emptying quickly, the headlamp washers will not operate every time that you use the windscreen washers.
49
Wipers and washers Rear window wiper blades
CHECKING THE WIPER BLADES
Lift the wiper arm and position the wiper blade at a right angle to the wiper arm. To remove, press the retaining clip, disengage the wiper blade and pull it off the arm in the opposite direction.
E66644
Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blade lips with water applied with a soft sponge.
CHANGING THE WIPER BLADES Windscreen wiper blades
E78156
Lift the wiper arm. Position the wiper blade at a right angle to the wiper arm. Remove the blade from the arm and replace it.
50
Lighting Main and dipped beam
LIGHTING CONTROL Lighting control positions
F
A
B
C
E71095
Pull the lever fully towards the steering wheel to switch between main and dipped beam.
Headlamp flasher
E
D
Pull the lever slightly towards the steering wheel.
E71094
Home safe lighting
A
Off
B
Side and tail lamps
C
Headlamps
D
Front fog lamps
E
Rear fog lamps
F
Parking lamps
Switch the ignition off and pull the direction indicator lever towards the steering wheel to switch the headlamps on. You will hear a short tone. The headlamps will go off automatically after 3 minutes with any door open, or 30 seconds after the last door has been closed. With all doors closed, but within the 30 second delay, opening any door will result in the 3 minute timer starting again.
Parking lamps CAUTION
The home safe lights can be cancelled by either pulling the direction indicator lever towards the steering wheel again or by turning the ignition switch ON.
Prolonged use of the parking lamps will discharge the battery. Switch off the ignition. Push the lighting control inwards and turn it to position F.
51
Lighting Note: You cannot switch the front fog lamps on if you have switched autolamps on.
AUTOLAMPS
REAR FOG LAMPS
E73840 E71097
Note: If you have switched autolamps on, you can only switch the main beam on when autolamps has switched the headlamps on.
WARNING Do not use the rear fog lamps when it is raining or snowing and visibility is more than 50 metres.
The headlamps will come on and go off automatically depending on the ambient light.
Note: You cannot switch the rear fog lamps on if you have switched autolamps on.
FRONT FOG LAMPS
ADJUSTING THE HEADLAMPS Xenon headlights Xenon headlamps can be adjusted for driving on the left or right hand side of the road by an expert.
Halogen headlamps Special foils can be used to adjust halogen headlamps for driving on the left or right hand side of the road.
E71096
WARNING Only use the front fog lamps when visibility is considerably restricted by fog, snow or rain.
AFS headlamps To adjust the headlamps for driving on the left or right hand side of the road:
52
Lighting Remove the headlamp assembly from the vehicle and remove the cover. See Changing a bulb (page 60).
When returning from abroad, set the lever back to position 1.
HEADLAMP LEVELLING
E65990 E78861
The level of the headlamp beams can be adjusted according to the vehicle load.
The headlamps are adjusted using a lever in the headlamp unit. Position 1 is the normal setting. For driving on the other side of the road, push the lever down to position 2.
Recommended headlamp levelling control positions Load Persons
Load in luggage
Front seats
Rear seats
compartment
Control position
1
1
-
-
0
2
-
-
0
2
3
-
1
2
3
Max
2
1
-
Max
3
1
See Vehicle identification plate (page 204). Higher control positions (+1) may be necessary when towing a trailer.
53
Lighting HAZARD WARNING FLASHERS
E71943
For item location: See Quick start (page 8).
Note: Depending on applicable laws and regulations in the country for which your vehicle was originally built, the hazard warning flashers may flash if you brake heavily.
54
Lighting ADAPTIVE FRONT LIGHTING SYSTEM (AFS)
A
A
B
B
E72897 A
without AFS
B
with AFS To activate the AFS when the daytime running lamps are activated, turn the lighting control to position C. See Lighting control (page 51).
The AFS adjusts the headlamp dipped beam depending on vehicle direction and speed. It improves visibility when you are driving at night and helps to reduce headlamp glare for oncoming drivers.
A message will appear in the information display and the headlamp indicator flashes if the system malfunctions. See Information messages (page 89). The headlamps will move to a fixed central or dipped position. Have the system checked as soon as possible.
The headlamps will also move when the vehicle is stationary and the steering wheel is turned. To prevent headlamp glare for the oncoming traffic, they will only move towards the passenger side of the vehicle. The system will not operate when you have switched on the daytime running lamps or when you have selected reverse gear.
55
Lighting DIRECTION INDICATORS
E71098
Note: Tap the lever up or down to make the direction indicators flash only three times.
56
Lighting Reading lamps
INTERIOR LAMPS Courtesy lamp
A B C
E71946 If you switch off the ignition, the reading lamps will go off automatically after some time to prevent the vehicle battery from discharging. To switch them back on, switch on the ignition for a short time.
E71945 A
Off
B
Door contact
C
On
Vanity mirror lamps
If you set the switch to position B, the courtesy lamp will come on when you unlock or open a door or the luggage compartment lid. If you leave a door open with the ignition switch off, the courtesy lamp will go off automatically after some time to prevent the vehicle battery from discharging. To switch it back on, switch on the ignition for a short time.
A B
E72900
The courtesy lamp will also come on when you switch off the ignition. It will go off automatically after a short time or when you start or restart the engine.
A
Off
B
On
If you switch off the ignition, the vanity mirror lamps will go off automatically after a short time to prevent the vehicle battery from discharging. To switch them back on, switch on the ignition for a short time.
If you set the switch to position C with the ignition switch off, the courtesy lamp will come on. It will go off automatically after a short time to prevent the vehicle battery from discharging. To switch it back on, switch on the ignition for a short time.
57
Lighting REMOVING A HEADLAMP
2 3
4 E78862
1.
Open the bonnet. See Opening and closing the bonnet (page 165). 2. Remove the screw. 3. Disconnect the electrical connectors. 4. Remove the headlamp.
58
Lighting Convertible
REMOVING A REAR LAMP 3-door and 5-door
3 2 2
3 E79717
4 E78870
1. 2. 3. 4.
4
Open the luggage compartment lid. Remove the screws. Disconnect the electrical connectors. Remove the rear lamp.
Estate
2
5 E79718
1. 2. 3. 4. 5.
3 4 E78876
1. 2. 3. 4.
Open the luggage compartment lid. Remove the screws. Disconnect the electrical connector. Remove the rear lamp.
59
Open the luggage compartment lid. Pull back the carpet. Remove the nut. Disconnect the electrical connectors. Remove the rear lamp.
Lighting CHANGING A BULB WARNINGS Switch the lights and the ignition off.
2
3
Let the bulb cool down before removing it. We recommend that you ask your dealer to change the bulbs if your vehicle is fitted with Xenon headlamps. There is a risk of injury due to high voltage.
E97738
4
2. Remove the cover. 3. Disconnect the electrical connector. 4. Remove the bulb.
CAUTIONS Do not touch the glass of the bulb. Only fit bulbs of the correct specification. See Bulb specification chart (page 70).
Headlamp main beam 1.
Remove the headlamp. See Removing a headlamp (page 58).
Note: You will need to remove the headlamp to change the headlamp, side lamp or front direction indicator bulbs. See Removing a headlamp (page 58). Note: You will need to remove the rear lamp to change the brake lamp, tail lamp or rear direction indicator bulbs. See Removing a rear lamp (page 59).
2
3
Note: The following instructions describe how to remove the bulbs. Fit replacements in the reverse order unless otherwise stated.
Headlamp dipped beam 1.
E97739
4
2. Remove the cover. 3. Disconnect the electrical connector 4. Remove the bulb.
Remove the headlamp. See Removing a headlamp (page 58).
Side lamps 1.
60
Remove the headlamp. See Removing a headlamp (page 58).
Lighting 3
2
All vehicles except Focus ST and Focus RS
4
1 2 E97755
2. Remove the cover. 3. Remove the bulb and the bulb holder. 4. Remove the bulb.
Front direction indicators 1.
Remove the headlamp. See Removing a headlamp (page 58).
E79592
1.
Using a suitable implement, remove the cover. 2. Remove the screws.
2
3
4
E97794
3
2. Turn the bulb holder anti-clockwise and remove it. 3. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
E79593
3. Disconnect the electrical connector. 4. Turn the bulb holder anti-clockwise and remove it.
Front fog lamps Note: For Focus ST and Focus RS, see your dealer. Note: You cannot separate the bulb from the bulb holder.
61
Lighting Side repeaters
2
1 3
4
E98659
3. Using a suitable implement release the retaining clip. Remove the bulb and the bulb holder. 4. Remove the bulb.
E98658
1.
Tip the mirror as far down as possible. Using a suitable implement release the retaining clip. 2. Remove the cover.
Approach lamps
1 E72264
62
Lighting 1.
3-door and 5-door
Turn the mirror glass as far inwards as possible. Using a suitable implement release the retaining clip.
2 A
3
B
2
2 E78871 E72265
2. Remove the lamp. 3. Remove the bulb.
A
Direction indicator lamp
B
Brake and tail lamp
1.
Remove the rear lamp. See Removing a rear lamp (page 59). 2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb.
Rear lamps - except convertible Note: Vehicles may not have a tail lamp if an LED board is fitted. The LED board is not a serviceable item, please consult your dealer if this fails.
Rear fog lamp, reversing lamp
3
1
2 E78872
1. Carefully remove the lamp. 2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb.
63
Lighting 4-door
Estate
A
B
2
2
C E78878
E78873
A
B
A
Brake and tail lamp
B
Direction indicator lamp
C
Reversing and fog lamp
1.
C
Remove the rear lamp. See Removing a rear lamp (page 59). 2. Remove the screw and remove the bulb holder. 3. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
D
Rear lamps - convertible
3
E78874
A
Brake lamp
B
Reversing lamp
C
Direction indicator lamp
D
Fog and tail lamp
Note: Vehicles may not have a tail lamp if an LED board is fitted. The LED board is not a serviceable item, please consult your dealer if this fails. Brake lamps 1.
1. Open the luggage compartment lid. 2. Remove the trim panel retaining clips and remove the trim panel. 3. Unclip the bulb holder. 4. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
64
Remove the rear lamp. See Removing a rear lamp (page 59).
Lighting 3
2
2
3
E79600
E79597
2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb.
2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb.
Rear direction indicators
Rear fog lamps
1.
1.
Remove the rear lamp. See Removing a rear lamp (page 59).
Open the luggage compartment lid.
3
2
2 E79595 E79599
2. Open the trim panel.
2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb.
3
Tail lamps 1.
Remove the rear lamp. See Removing a rear lamp (page 59).
4 E79596
3. Turn the bulb holder anti-clockwise and remove it.
65
Lighting 4. Remove the bulb.
Central brake lamp
Reversing lamps
3-door, 5-door and Estate
1.
Open the luggage compartment lid.
2
1 2 E78879
1. Remove the screws. 2. Remove the lamp.
E79595
2. Open the trim panel.
3
4
4 E79598
3. Turn the bulb holder anti-clockwise and remove it. 4. Remove the bulb.
3 E79601
3. Unclip the bulb holder. 4. Remove the bulb.
66
Lighting 4-door
2 3
x17
2
E79602
2. Remove the luggage compartment lid trim.
1 E78880
4
1. Remove the cover. 2. Disconnect the electrical connector. 3. Unclip the bulb holder.
3 E79603
3. Disconnect the electrical connector. 4. Unclip the bulb holder.
4 5 E78881
4. Remove the bulb. Convertible 1.
E79604
Open the luggage compartment lid.
5. Remove the bulb.
67
Lighting Luggage compartment lamp
Front interior lamp Vehicles with a perimeter alarm
2
1
1
3
2 E79605
1. Carefully prise out the lamp. 2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb.
E78128
1. Carefully prise out the lamp. 2. Remove the lens.
Number plate lamp
3
2
3 E78129
3. Remove the bulb.
1 E79606
1. Remove the screws. 2. Remove the lens. 3. Remove the bulb.
68
Lighting Vehicles with a category one alarm
1. Carefully prise out the lamp. 2. Turn the bulb holder anti-clockwise and remove it.
1
2 E73091
1. Carefully prise out the lamp. 2. Remove the lens.
3
E73939
3. Remove the bulb.
Vanity mirror lamps
2 3 E73092
1
3. Remove the bulb. E78131
Front reading lamps
1. Carefully prise out the lamp. 2. Remove the bulb.
2 1 E73938
69
Lighting BULB SPECIFICATION CHART Bulb
Specification (Watts)
Approach lamp
5
Brake and tail lamp (3-door, 5-door and Estate) Brake lamp
5/21 21
Central brake lamp
5
Fog and tail lamp (4-door)
5/21
Front direction indicator
21
Front fog lamp
35 (H8)
Headlamp dipped beam
55 (H7)
Headlamp main beam
55 (H1)
Interior lamp
10
Luggage compartment lamp
5
Number plate lamp
5
Reading lamp
5
Rear direction indicator
21
Rear fog lamp
21
Reversing lamp
21
Side lamp
5
Side repeater
5
Side repeater on exterior mirror
5
Tail lamp (convertible)
5
Vanity mirror
5
70
Windows and mirrors Note: On vehicles with a convertible top, the automatically closing function is not available on the rear quarter windows.
ELECTRIC WINDOWS WARNING
Safety switch for rear windows
Do not operate the electric windows unless they are free from obstruction.
Note: You can always operate the rear windows from the driver’s door.
Note: If you operate the switches often during a short period of time, the system might become inoperable for a certain time to prevent damage due to overheating. Switch on the ignition to operate the electric windows.
Global opening and closing You can also operate the electric windows with the ignition off via the global opening and closing function. See Locks (page 33).
E70850
A switch in the driver’s door disables the rear electric window switches.
Driver's door switches
The light in the switch comes on and the lights in the rear window switches go off when the rear windows are disabled.
You can operate all the windows with the switches on the door trim panel of the driver’s door.
Anti-trap function WARNING Careless closing of the windows can override the protection function and cause injuries. The electric windows will stop automatically while closing and reverse some distance if there is an obstacle in the way.
E70848
Opening and closing the windows automatically Press or lift the switch to the second action point and release it completely. Press or lift it again to stop the windows.
71
Windows and mirrors Overriding the anti-trap function
4. Push and hold the switch until the window is fully open. 5. Release the switch. 6. Lift and hold the switch until the window is fully closed. 7. Open the window and try to close it automatically. 8. Reset and repeat procedure if the window does not close automatically.
CAUTION While you close the window for the third time, the anti-trap function is disabled. Make sure there are no obstacles in the way of the closing window. To override this protection function when there is a resistance, e.g. in the winter, proceed as follows:
EXTERIOR MIRRORS
1.
Close the window twice until it reaches the resistance and let it reverse. 2. Close the window a third time to the resistance. The anti-trap function is disabled and you cannot close the window automatically. The window will override the resistance and you can close it fully. 3. If the window does not close after the third attempt, have it checked by an expert.
WARNING Do not overestimate the distance of the objects that you see in the convex mirror. Objects seen in convex mirrors will appear smaller and further away than they actually are.
Manual folding mirrors Folding Push the mirror towards the door window glass.
Resetting the memory of the electric windows
Unfolding
WARNING
Make sure that you fully engage the mirror in its support when returning it to its original position.
The anti-trap function is deactivated until you have reset the memory. After the battery has been disconnected from the vehicle you must reset the memory separately for each window: Note: On vehicles with a convertible top, the roof and doors must be fully closed before carrying out the following procedure. 1.
Lift and hold the switch until the window is fully closed. 2. Release the switch. 3. Lift the switch again for one more second.
72
Windows and mirrors On some models, the door mirrors are heated when the heated rear window is switched on.
ELECTRIC EXTERIOR MIRRORS
Electric folding mirrors
A
C B
E70846
E78811
A
Left-hand mirror
B
Off
C
Right-hand mirror
Note: When the mirrors are operated often during a short period of time, the system might become inoperable for a certain time to prevent damage due to overheating.
The switch is located in the trim panel of the driver’s door.
To fold/unfold the mirrors, briefly press the switch. If the switch is pressed again while the mirrors are moving, they will stop and reverse the direction of movement.
Mirror tilting positions
INTERIOR MIRROR
E71272
Dip the mirror to reduce glare when driving at night.
E70847
73
Windows and mirrors AUTO-DIMMING MIRROR
E71028 The auto-dimming mirror will adjust automatically when hit by glaring light from behind. It will not work when you have selected reverse gear.
74
Instruments GAUGES Type 1
A
B
C
E E98733
A
Tachometer
B
Engine coolant temperature gauge
C
Fuel gauge
D
Speedometer
E
Information display
75
D
Instruments Type 2 and 3
A
B
C
E E98738
A
Tachometer
B
Engine coolant temperature gauge
C
Fuel gauge
D
Speedometer
E
Information display
76
D
Instruments Focus ST and Focus RS
A
B
If it enters the red section, the engine is overheating. Reduce engine speed as soon as safely possible to allow the engine to cool. If the engine is continued to be driven at high engine speeds with the needle in the red section, the engine speed will be reduced automatically to prevent engine damage.
C
Turbocharger boost gauge
E78808
A
Oil temperature gauge
B
Turbocharger boost gauge
C
Oil pressure gauge
Indicates the added intake pressure provided by the turbocharger.
Oil pressure gauge WARNING
Engine coolant temperature gauge
Driving with your oil pressure gauge pointer continuously in the red section of the scale may damage the engine.
All vehicles Shows the temperature of the engine coolant. At normal operating temperature, the needle will remain in the centre section.
Note: When the engine is cold, oil pressure close to 5 bar may be indicated. This is normal. As the engine warms up, the oil pressure will drop.
CAUTION
This gauge indicates engine oil pressure up to a recommended safe maximum of 5 bar.
Do not restart the engine until the cause of overheating has been resolved.
During normal driving the indicated oil pressure will vary with engine speed, the pressure rising as engine speed rises and dropping as engine speed drops.
If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down. See Engine coolant check (page 179).
If the engine oil pressure drops below the normal range, the oil pressure gauge pointer will drop into the red section of the gauge scale and the engine oil pressure warning lamp in the main instrument cluster will illuminate. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed. See Engine oil check (page 178).
Oil temperature gauge Indicates the temperature of the engine oil. At normal operating temperature, the needle remains within the normal area.
77
Instruments Fuel gauge
Airbag warning lamp
The arrow adjacent to the fuel pump symbol indicates on which side of the vehicle the fuel filler cap is located.
If it illuminates when driving, this indicates a malfunction. Have the system checked by a properly trained technician.
WARNING LAMPS AND INDICATORS
Brake system warning lamp WARNING
The following warning lamps and indicators will come on briefly when you switch the ignition on to confirm that the system is operational: • ABS • Airbag • Brake system • Doors open • Engine • Engine immobiliser • Engine systems fault • Frost • Ignition • Oil pressure • Power steering • Stability control (ESP)
Reduce your speed gradually. Use your brakes with great care. Do not step on the brake pedal abruptly. It illuminates when the parking brake is engaged. It will also illuminate if the brake fluid level falls below the MIN mark. See Brake and clutch fluid check (page 180). WARNING Have this checked immediately.
If the brake system warning lamp illuminates with the ABS warning lamp, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and have this checked before continuing you journey.
If a warning or indicator lamp does not illuminate when the ignition is switched on, this indicates a malfunction. Have the system checked by properly trained technician.
Cruise control indicator It will illuminate when you have set a speed using the cruise E71340 control system. See Using cruise control (page 137).
ABS warning lamp If it illuminates when driving, this indicates a malfunction. Have the system checked by a properly trained technician. You will continue to have normal braking (without ABS) but have this checked as soon as possible.
Direction indicator Flashes during operation. A sudden increase in the rate of flashing warns of a failed indicator bulb. See Changing a bulb (page 60).
78
Instruments Doors open warning lamp
Glow plug indicator
It will illuminate when you switch the ignition on if you have not closed the doors, the bonnet or luggage compartment properly.
If the glow plug indicator lamp illuminates, wait until the it extinguishes before starting.
Headlamp indicator Engine warning lamp
It will illuminate when you switch the headlamp dipped beam or the side and tail lamps on.
If it illuminates when the engine is running, this indicates a malfunction. If it flashes when you are driving, reduce the speed of your vehicle immediately. If it continues to flash, avoid heavy acceleration or deceleration. The engine will continue to run but it will have limited power. Have this checked immediately.
Ignition warning lamp Note: If the battery voltage is too high or too low, the ignition warning lamp will illuminate and the heated windscreen and heated rear window, the auxiliary heater or the air conditioning may switch on or off automatically.
CAUTION If the engine warning lamp illuminates in conjunction with a message, have the system checked as soon as possible.
If it illuminates when you are driving, this indicates a malfunction. Switch off all unnecessary electrical equipment. Have the system checked by a properly trained technician immediately.
Front fog lamp indicator It will illuminate when you switch the front fog lamps on.
Low fuel level warning lamp If it illuminates, refuel as soon as possible.
Frost warning lamp WARNING
Main beam indicator
Even if the temperature rises to above +4ºC there is no guarantee that the road is free of hazards caused by inclement weather.
It will illuminate when you switch the headlamp main beam on. It will flash when you use the headlamp flasher.
It will illuminate orange when the temperatures is between +4°C and +1°C. At temperatures below +1°C, the warning lamp glows red.
Message indicator It will illuminate when a new message is stored in the information display. See Information messages (page 89).
79
Instruments Oil pressure warning lamp
Stability control (ESP) indicator It will flash when either system is operating. If it does not flash or it comes on when you are driving, this indicates a malfunction. Have the system checked by a properly trained technician immediately.
CAUTION Do not resume your journey if the oil pressure warning lamp illuminates despite the oil level being correct. Have the system checked by a properly trained technician immediately.
If you switch ESP off, the warning lamp will come on. The lamp will go out when you switch the system back on or when you switch the ignition off.
If the lamp stays on after starting or illuminates during a journey, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine oil check (page 178).
AUDIBLE WARNINGS AND INDICATORS
Power steering warning lamp
Automatic transmission
It illuminates to indicate a malfunction of the power steering system. Full steering will be maintained but you will need to exert greater force on the steering wheel. Have the system checked by a properly trained technician as soon as possible.
If position P is not selected, a warning chime will sound when the driver’s door is opened.
Frost WARNING Even if the temperature rises to above +4ºC there is no guarantee that the road is free of hazards caused by inclement weather.
Rear fog lamp indicator It will illuminate when you switch the rear fog lamps on.
A warning chime will sound in the following conditions: • +4ºC or lower: frost warning • 0ºC or lower: danger of icy roads
Seat belt reminder See Seat belt reminder (page 27).
Key outside car Shift indicator
Vehicles with the key free system
It will illuminate to inform you that shifting to a higher gear may give better fuel economy and lower CO2 emissions. It will not illuminate during periods of high acceleration, braking or when the clutch pedal is pressed.
If the engine is running and a passive key is no longer detected within the vehicle interior, a chime will sound as soon as the door is closed.
80
Instruments Lights on A warning chime will sound if the driver’s door is opened with the exterior lights switched on and the ignition switched off.
Low fuel A warning chime will sound at the following ranges: 80 km (50 miles), 40 km (25 miles), 20 km (12 miles), 0 km (0 miles).
Seat belt reminder WARNINGS The seat belt reminder remains in stand-by mode after the driver or front passenger has fastened his or her seat belt. It will be reactivated if the driver or front passenger unbuckles his or her seat belt. Never sit on top of a buckled seat belt to avoid the seat belt reminder function. The restraint system can only work properly if passengers have buckled up their seat belts. Note: Placing objects on the front passenger’s seat when it is not occupied may trigger the sensors in the seat and activate the seat belt reminder if the seat belt is not engaged. When the vehicle’s speed exceeds 23 km/h (14 mph), a chime will sound if the driver’s or front passenger’s seat belt is unbuckled. The chime will stop after eight minutes.
Stop vehicle - roof operation A warning chime will sound if the roof opening or closing sequence was enabled during vehicle stand still and driving started.
81
Information displays Turn the rotary control to scroll through the available displays within a menu or to choose a setting. To scroll automatically, hold the rotary control in the upward or downward position.
GENERAL INFORMATION WARNING Do not operate the information display controls when the vehicle is moving. Various systems can be programmed using the information display and the multi-function lever on the steering column.
Controls E73266
Press the SET/RESET button to choose a sub-menu and adjust the settings. If the chimes are activated, a short tone will sound each time the button is pressed.
E73265
Type 2 and 3
82
Information displays Menu structure
Reset Trip Trip Odo Avg Fuel Avg Speed All Messages Car Setup Steering
Measure Unit Chimes Low Fuel General Warn General Info Door Ajar Key Free act. E98876
Aux Heater
84
English German Italian French Spanish Turkish Russian Dutch Polish Swedish Portuguese Metric Imperial
Information displays Distance to empty
A
Indicates the approximate distance the vehicle will travel on the fuel remaining in the tank. Changes in driving pattern may cause the value to vary.
Park Heater Time 1 on
Instantaneous fuel consumption
Set Time 1 Monday Tuesday Wednesday Thursday Friday Saturday Sunday Time 2 on
Indicates the current average fuel consumption. Average fuel consumption Indicates the average fuel consumption since the function was last reset. Average speed Indicates the average speed calculated since the function was last reset.
Set Time 1 Monday Tuesday Wednesday Thursday Friday Saturday Sunday
Outside air temperature Shows the outside air temperature. Hold 'SET' to set Tyre Pres.
Set once
Recalibrates the system to the actual pressure of the tyres. See Tyre pressure monitoring system (page 198).
Active now
Menu
E98884
Enters the main menu. See General information (page 82).
TRIP COMPUTER Type 2 and 3 Odometer Registers the total mileage of the vehicle. Tripmeter Registers the mileage of individual journeys.
85
Information displays
10:20 Trip
Average Fuel l 6.3 100km
A
123456 km
B
234.2 km
C
Dist to empty Instant Fuel Average Fuel Average Speed
E74428 A
Trip computer
B
Odometer
C
Tripmeter
Outside Air Hold ‘SET’ to set Tyre Pres
The trip computer includes the following information displays:
Menu E105166
Turn the rotary control to scroll through the trip computer displays. Note: The position of the trip computer display may vary depending on the information shown in the display. Resetting the trip computer using the main menu To reset a particular display: 1.
Turn the rotary control and highlight Menu.
2. Press the SET/RESET button. 3. Highlight "Reset Trip". 4. Press the SET/RESET button. 5. Highlight the function to be reset. 6. Press and hold the SET/RESET button.
86
Information displays Scroll to this display using the rotary control and press the SET/RESET button to select the desired language. Turn the rotary control to save the setting and exit the menu.
PERSONALISED SETTINGS Car Setup menu Note: For road safety reasons, changes in the Car Setup menu can only be made while the vehicle is stationary. If this menu or one of its sub-menus is open when the vehicle begins to move, the information display will automatically exit the Car Setup menu.
Clock setting Note: This display is only present on vehicles equipped with a programmable auxiliary heater but no Ford audio or navigation system. If the vehicle is equipped with a Ford audio or navigation system, the time is set on the audio or navigation system. See separate audio or navigation handbook.
Use the rotary control to scroll through the displays and press SET/RESET to choose a sub-menu and adjust the settings. Scroll to the Car Setup display using the rotary control and press the SET/RESET button.
Scroll to this display using the rotary control and press SET/RESET. The hours start to flash and can be set using the rotary control.
EHPAS personalisation
Press the SET/RESET button to confirm the setting and move to the minutes.
Note: When the vehicle is stationary, the steering assistance is optimized in all three settings and does not differ noticeably.
Proceed in the same way to set the minutes and the date.
Standard: The standard setting suitable for all driving styles.
After setting the year and pressing SET/RESET, the time and date are stored.
Sport: The steering assistance is reduced. This suits a sportier driving style by increasing the feedback through the steering wheel. The sport setting is also an advantage when driving on icy and snowy road conditions.
Units of measure To toggle between metric and imperial units, scroll to this display and press the SET/RESET button.
Comfort: The steering assistance is increased. The steering will feel lighter and you will not need to exert as much force on the wheel.
Toggling the units of measure using this display will affect the following displays: • Distance to empty • Average fuel consumption • Instantaneous fuel consumption • Average speed • Outside air temperature • The temperature display in the automatic climate control.
ESP Select this option to activate ESP.
Language setting A choice of eleven languages are available.
87
Information displays The units of measure for outside air temperature and the automatic climate control can be toggled independent of the other displays. See General information (page 82).
Four functions are available for setting the times at which the vehicle should be warmed up: Seven days in the week
Auxiliary heater programming
One or two times can be programmed for every day of the week.
See Auxiliary heater (page 101).
Five days in the week
To programme the auxiliary heater, scroll to this display using the rotary control and press the SET/RESET button.
One or two times can be programmed for the days Monday to Friday.
Instant control
One or two times can be programmed for one particular day of the week.
Single day within week
To switch on the programmable auxiliary heater or fuel operated heater, scroll to this display and press SET/RESET. The cursor will change to a tick. The tick in this display confirms that the heater is now activated and will perform one heating cycle.
Any time and date One time can be programmed for one particular day in the next 12 months from the date of programming. Programming procedure for Seven days in the week, Five days in the week, Single day within week:
AUX. HEATER ON will appear in the display.
In the Auxiliary heater programming menu, scroll to the relevant display using the rotary control and press the SET/RESET button.
To switch off the programmable auxiliary heater or fuel operated heater during a heating cycle, scroll to this display and press SET/RESET. The cursor will change to a tick. The tick in this display confirms that the heater is now deactivated.
When programming the function Single day within week, choose the day using the rotary control and press SET/RESET. The first programme time will flash.
AUX. HEATER OFF will appear in the display.
Press SET/RESET and the hours will flash.
Programme times
Set the hours with the rotary control.
Note: The programmed time is the time at which you wish the vehicle to be warm and ready to drive, not the time at which the heater switches on.
Press SET/RESET and the minutes will flash.
Note: Times must be programmed at least 70 minutes in advance of the time you wish to set.
Press SET/RESET and the second programme time will flash. Repeat to set the second programme time.
Set the minutes with the rotary control.
Note: The time and date must be correctly set on the audio/ navigation system or on the information display. See Clock setting.
88
Information displays Note: If only one programme time is desired, select dashes when scrolling through the hours and minutes. These appear between 23 and 00 hours and between 59 and 00 minutes.
Proceed in the same way to set the minutes, the month and the day. After setting the day, press SET/RESET and the cursor will flash. Press SET/RESET to confirm the settings. The cursor will change to a tick. The tick confirms that the time schedule is now stored and the heater will have the vehicle warmed up at the time set.
After setting the minutes of the second programme time, press SET/RESET and the cursor will flash. Press SET/RESET again and the cursor will change to a tick. The tick confirms that the time schedules are now stored and that the heater will have the vehicle warmed up at the times set.
To deactivate the function, scroll to this display and press SET/RESET repeatedly until the tick flashes. Press SET/RESET again to delete the tick and deactivate the function.
Note: It is not possible to select the Seven days in the week, Five days in the week and Single day within week functions simultaneously as only one set of times can be programmed for each day.
Chime deactivation The following chimes can be deactivated: • Low fuel warning. • General warning messages. • General information messages. • Door ajar.
If programme times for one of these functions are stored and active, confirmed by a tick, a lock symbol will appear in the programming display of the other two, showing that these functions cannot be activated. To activate one of the other two functions, first deactivate the function currently active by deleting the tick.
INFORMATION MESSAGES
To deactivate the function, scroll to the relevant display and press SET/RESET repeatedly until the tick flashes. Press SET/RESET again to delete the tick and deactivate the function. Programming procedure for Any time and date In the Auxiliary heater programming menu, scroll to this display using the rotary control and press the SET/RESET button.
E73265
The hours will flash. Set the hours with the rotary control. Press SET/RESET and the minutes will flash.
89
Information displays Message symbols See Owner’s handbook.
Have the system checked at the next service. Have the system checked as soon as possible. E73266
Stop your vehicle as soon as it is safe to do so.
Press SET/RESET to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time.
Viewing current messages Type 2 and 3
With instrument cluster type 2 and 3, certain messages need to be confirmed before you can access the menus.
1.
Scroll to this display using the rotary control and press the SET/RESET button. 2. Turn the rotary control to scroll through the available messages. 3. Press SET/RESET to acknowledge the message and exit the menu.
Message indicator The message indicator illuminates to supplement some messages. It will be red or amber depending on the severity of the message and will remain on until the cause of the message has been rectified.
Convertible top Message
Warning lamp
System
red
Stop vehicle to operate. Roof opening or closing sequence was enabled during vehicle stand still, driving started.
Close luggage comp. separator
amber
Deploy the luggage compartment separator or close the luggage compartment lid.
Roof needs engine running
amber
Start the engine to operate.
Roof malfunct. service reqd.
amber
Permanent malfunction. Have the system checked by a properly trained technician.
Stop vehicle - Roof operation
90
Information displays Message
Complete roof operation
Roof operating
Warning lamp
System
amber
Opening or closing sequence not complete. Convertible top is not locked. Press the convertible top switch until sequence is complete.
-
Progress information.
Doors open Message
Warning lamp
System
Driver door open
red
Locks.
Driver side rear door open
red
Locks.
Passenger door open
red
Locks.
Passenger side rear door open
red
Locks.
Luggage comp. open
red
Locks.
Bonnet open
red
Locks.
Door ajar close door
amber
Locks. Close all the doors to start the car.
Warning lamp
System
Keyless system Message
Immobiliser malfunction
Steering malfunction
Key not detected
red
Keyless system.
red
You will ONLY be able restart your vehicle up to a maximum of five times or for a period of up to 56 hours after which the vehicle cannot be started. Have the system checked by a properly trained technician as soon as possible.
amber
91
Keyless system. See Keyless entry (page 37).
Information displays Message
Warning lamp
System
Key outside car
amber
Keyless system. See Keyless entry (page 37).
Remote key battery low
amber
Change battery. See Changing the remote control battery (page 30).
Steering malfunction
-
Have your vehicle checked by a properly trained technician.
To start press brake
-
Keyless system.
To start press clutch
-
Keyless system.
Lighting Message
Brake light fault
Adaptive front light failure
Warning lamp
System
red
Brake lamp switch. The vehicle can be driven as normal. However, cruise control cannot be switched on. Have the system checked by a properly trained technician as soon as possible.
amber
Adaptive front lighting system (AFS).
Maintenance Message
Warning lamp
System
High engine temperature
red
Cooling system.
Low brake fluid level
red
Brakes.
red
Engine. Stop the vehicle as soon as safely possible and switch off the engine immediately. Have the system checked by a properly trained technician immediately.
Engine malfunction
92
Information displays Message
Warning lamp
System
Acceleration reduced
red
Electronic acceleration control (EAC). The vehicle can be driven but the acceleration rate will be noticeably reduced. Maximum vehicle speed will be maintained. Have the system checked by a properly trained technician as soon as possible.
Low washer fluid level
amber
Service oil
-
Screen washer. Service Indication
Power steering Message
Power steering malfunction
Warning lamp
System
red
Power steering. Full steering will be maintained but you will need to exert greater force on the steering wheel. Have the system checked by a properly trained technician as soon as possible.
Transmission Message
Transm. overt. Press brake
Warning lamp
System
red
Under certain driving conditions it is possible that the clutches in the transmission can overheat. In these circumstances it is necessary to press the brake pedal and stop the vehicle to prevent damage to the transmission. Select N (NEUTRAL) or P (PARK) and apply the parking brake until the transmission has cooled and the message disappears from the display.
93
Information displays Message
Warning lamp
System
Trans. too hot Press brake
red
The transmission is too hot. In these extreme conditions the transmission will disengage drive in order to prevent damage. You will not be able to drive until the transmission has cooled.
Transmission malfunction
amber
Automatic transmission.
Engagement in progress Press brake pedal
-
At low outside temperatures, after starting the engine, it may take the transmission several seconds to engage R (REVERSE) or D (DRIVE). Keep the brake pedal depressed until these messages disappear from the display.
Move shifter to P
-
Automatic transmission.
Tyre pressure monitoring system Message
Warning lamp
System
Check tyre pressures
amber
The pressure in one or more tyres has dropped. Check as soon as possible.
Tyre Press. Sys malfunction
amber
Permanent malfunction. Have your vehicle checked by a properly trained technician.
Warning lamp
System
amber
Stability control (ESP). Have your vehicle checked by a properly trained technician.
Stability control (ESP) Message
ESP malfunction
94
Climate control Warming the interior
PRINCIPLE OF OPERATION
Direct the air towards your feet. In cold or humid weather conditions, direct some of the air towards the windscreen and the door windows.
Outside air Keep the air intakes forward of the windscreen free from obstruction (snow, leaves etc.) to allow the climate control system to function effectively.
Cooling the interior Direct the air towards your face.
Recirculated air
AIR VENTS
CAUTION Prolonged use of recirculated air may cause the windows to mist up. If the windows mist up, follow the settings for defrosting and demisting the windscreen. The air currently in the passenger compartment will be recirculated. Outside air will not enter the vehicle.
E78809
Heating
MANUAL CLIMATE CONTROL
Heating performance depends on the temperature of the engine coolant.
Air distribution control
Air conditioning
A
Note: The air conditioning operates only when the temperature is above 4ºC (39ºF).
F
B
E
C
Note: If you use the air conditioning, the fuel consumption of your vehicle will be higher. Air is directed through the evaporator where it is cooled. Humidity is extracted from the air to help keep the windows free of mist. The resulting condensation is directed to the outside of the vehicle and it is therefore normal if you see a small pool of water under your vehicle.
E71379
D
General information on controlling the interior climate
A
Windscreen
Fully close all the windows.
B
Footwell and windscreen
95
Climate control C
Footwell
D
Face level and footwell
E
Face level
F
Face level and windscreen
Ventilation
You can set the air distribution control to any position between the symbols.
Blower
E71378 Set the air distribution control, blower and air vents to suit your requirements.
Air conditioning
A
Switching the air conditioning on and off
If you turn the blower off, the air conditioning will turn off. When you turn the blower on again, the air conditioning will come on automatically.
E75470 A
Off
Note: If you switch the blower off, the windscreen may mist up.
Cooling with outside air
Recirculated air
Press the button to toggle between outside air and recirculated air.
Heating the interior quickly E71380
E71377
96
Climate control Cooling the interior quickly
When the temperature is above 4°C (39°F), the air conditioning will switch on automatically. Make sure that the blower is on. The indicator in the switch will illuminate during defrosting and demisting. If you move the air distribution control to a position other than A, the A/C will remain on. You can switch the air conditioning and recirculated air on and off while the air distribution control is set to position A. If necessary, switch the heated windows on. See Heated windows and mirrors (page 100).
E71381 Defrosting and demisting the windscreen
Note: To defrost or demist the rear side windows, set the second row air vents to the defrosting and demisting position. See Air vents (page 95). Reducing interior air humidity
E71382
E71383
97
Climate control AUTOMATIC CLIMATE CONTROL
E91390
Note: A description of the Ford DVD-Navigation System in combination with the automatic climate control is provided in the separate manual.
The system controls the temperature, amount and distribution of the air flow automatically and adjusts them according to the driving and weather conditions. Pressing the AUTO button once switches on the auto mode.
Setting the temperature
The system in your vehicle is dual-zone automatic climate control. When the system is in mono mode, all the temperature zones are linked to the driver's zone. When you switch mono mode off, the dual-zone system allows you to set different temperatures for the driver's and front passenger's side. Note: Avoid adjusting the settings when the vehicle interior is extremely hot or cold. The automatic climate control adjusts to the current circumstances automatically. For the system to function properly, the side and centre vents should be fully open.
E91391
You can set the temperature between 16ºC and 28ºC in steps of 0.5ºC. In position LO (below 16ºC) the system will switch to permanent cooling, in HI (above 28ºC) to permanent heating, and not regulate a stable temperature.
Note: The sunload sensor is located on top of the instrument panel. Do not cover the sensor with any objects. Note: At low outside temperatures, when the system is in auto mode, the air stream will be directed to the windscreen and the side windows as long as the engine is cold.
98
Climate control Mono mode
Use the buttons to adjust the blower speed.
In mono mode, the temperature settings for both the driver’s and passenger’s side are linked. If you adjust the temperature using the rotary control on the driver’s side, the settings will be adjusted to the same setting on the passenger’s side. In mono mode, MONO appears in the display.
The blower setting is indicated in the display. To return to auto mode, press the AUTO button.
Air distribution To adjust air distribution, press the desired button. Any combination of settings can be selected simultaneously.
To switch mono mode off Select a temperature for the passenger’s side with the rotary control on the passenger’s side. Mono mode will switch off and MONO disappears from the display. The temperature for the driver’s side will remain unchanged. You can now adjust the driver and passenger side temperatures independently of each another. The temperature settings for each side are shown in the display. You can set a temperature difference of up to 4ºC.
A
B
C
E70308
Note: If you set a temperature of greater than 4°C, the temperature on the other side will be adjusted so that the difference remains 4°C.
A
Footwell
B
Face level
C
Windscreen
When you select windscreen defrosting and demisting, A, B and C switch off automatically and the air conditioning switches on. Outside air will flow into the vehicle. You cannot select recirculated air.
Note: If you set one of the sides to HI or LO, both sides will be set to HI or LO.
To switch mono mode back on
Windscreen defrosting and demisting To switch mono mode back on, press the MONO button. MONO reappears in the display and the passenger’s side temperature will be adjusted to the driver’s side temperature.
E91392
Press the windscreen defrosting and demisting button. Outside air will flow into the vehicle. Air conditioning is automatically selected. As long as the air distribution is set to this position, you cannot select recirculated air.
Blower
99
Climate control The blower speed and the temperature control operate automatically and cannot be adjusted manually. The blower is set to high speed and the temperature to HI.
When switched off, the heating, ventilation and air conditioning system is switched off and recirculated air is selected.
When you select windscreen defrosting and demisting, the heated screens switch on automatically and switch off after a short time.
HEATED WINDOWS AND MIRRORS Heated windows
To return to auto mode, press the AUTO button.
Use the heated windows to defrost or demist the windscreen or rear window.
Switching the air conditioning on and off
Note: The heated windows operate only when the engine is running. Heated windscreen
E91393
Note: Also defrosts the front washer jets.
Press the A/C button to switch the air conditioning on and off. A/C OFF appears in the display when the air conditioning is switched off. A/C ON appears in the display when the air conditioning is switched on.
E78039
Heated rear window
Recirculated air
E78040
Press the recirculated air button to toggle between outside air and recirculated air.
Heated exterior mirrors
Note: When the system is in auto mode and the interior and exterior temperatures are quite hot, the system selects recirculated air automatically to maximise cooling of the interior. Once the selected temperature is reached, the system will reselect outside air automatically.
Electric exterior mirrors are fitted with a heating element that will defrost or demist the mirror glass. They will switch on automatically when you switch the heated rear window on.
Switching off the automatic climate control
E91394
Press the OFF button.
100
Climate control Used properly, the programmable auxiliary heater provides the following benefits: • It preheats the interior of the vehicle. • It keeps the windows clear of ice in the event of frost and prevents condensation. • It avoids cold starts and allows the engine to reach operating temperature sooner.
AUXILIARY HEATER Programmable auxiliary heater WARNINGS The programmable auxiliary heater must not be operated in enclosed spaces, at filling stations or near sources of combustible vapours or dust. The programmable auxiliary heater should be switched on for approximately 10 minutes at least once a month all year round. This prevents the water pump and heater motor from seizing.
The programmable auxiliary heater may also be used while the vehicle is in motion to help the vehicle heater and warm up the interior more quickly. To prevent the battery from discharging: • Once the programmable auxiliary heater has performed one heating cycle, the next programmed heater time will only be carried out if the vehicle’s engine has been started in between. • After a heating cycle, the vehicle should be driven for at least the period of the heating cycle.
To avoid corrosion, the coolant in your vehicle should contain at least 10 % antifreeze all year round. Note: The programmable auxiliary heater will only operate if there is at least 7.5 litres of fuel in the fuel tank. Note: The heating depends on the outside air temperature. Note: It is possible that when the programmable auxiliary heater is activated, exhaust fumes may come from under the sides of the vehicle. This is normal.
Programming the auxiliary heater
Note: On vehicles with manual climate control the heating of the vehicle interior is dependent on the temperature, air distribution and blower control settings.
Auxiliary heater
The auxiliary heater is programmed using the information display. See Information displays (page 82).
The diesel auxiliary heater (PTC electrical heater) aids in warming the engine and the interior compartment on vehicles with diesel engines. It is automatically switched on or off depending on the outside temperature, the coolant temperature and the alternator load.
The programmable auxiliary heater operates independently of the vehicle heater by heating the engine’s coolant circuit. It is fed from the vehicle fuel tank.
101
Climate control Fuel operated heater
Note: When the switches are operated often during a short period of time, the system might become inoperable for a certain time to prevent damage due to overheating.
The fuel operated heater aids in warming the engine and the interior compartment on vehicles with a petrol or diesel engine. It is automatically switched on or off depending on the outside temperature and the coolant temperature, unless it has been deactivated by the driver.
Note: The electric sunroof can also be operated with the ignition off via the global opening and global closing function. See Global opening and closing (page 39).
When the fuel operated heater is operating, a message appears in the information display.
There are two ways of opening the sunroof – the rear of the sunroof lifts open or the sunroof opens from the front, sliding back under the roof. The sunroof opens and closes whilst the switch is pressed.
The fuel operated heater can be deactivated using the information display. See Information displays (page 82).
ELECTRIC SUNROOF
Switch on the ignition to operate the electric sunroof. The power sunroof is operated by a switch located between the sun visors.
Opening and closing the sunroof
E78054 E72188
WARNING
B
Before operating the electric sunroof you should verify it is free of obstructions and ensure that children and/or pets are not in the proximity of the sunroof opening. Failure to do so could result in serious personal injury. It is the primary responsibility of the supervising adults to never leave a child unattended in a vehicle and to never leave the keys in an unattended vehicle.
E72185
102
A
A
Press to close
B
Press to open
Climate control Tilting the sunroof
Sunroof anti-trap protection WARNINGS The anti-trap function is deactivated until the memory has been reset. Careless closing of the window can cause injuries. Careless closing of the electric sunroof can override the anti-trap protection and cause injuries. The sunroof will stop automatically while closing and reverse some distance if there is an obstacle in the way.
E72189
B
E72185
To override anti-trap protection when there is a resistance, e. g. in the winter, proceed as follows:
A
A
Press to open
B
Press to close
WARNING While the sunroof is being closed for the third time, the anti-trap function is disabled. Make sure there are no obstacles in the way of the closing sunroof.
Opening and closing the sunroof automatically
Close the sunroof a third time to the resistance. The anti-trap function is disabled and the sunroof cannot be closed automatically. The sunroof will override the resistance and can then be closed fully.
Note: When opening automatically, the sunroof will stop about 8 cm from the fully opened position. This position reduces the buffeting noise which is sometimes heard when the sunroof is fully open. The sunroof will only stop automatically in this position when the sunroof is opened automatically.
If the sunroof does not close after the third attempt, have it checked by an expert.
To open or close the sunroof automatically press either side of the switch to the second action point and release it completely. Press again to stop.
Sunroof safety mode WARNING
When the closed position is reached, the sunroof stops automatically.
The anti-trap function is not active during this procedure. Make sure that there are no obstacles in the way of the closing sunroof.
103
Climate control If the system detects a malfunction, it enters a safety mode. The sunroof will move for only about 0.5 seconds at a time and then stop again. Close the sunroof by pressing the button again when the sunroof stops moving. When the rear of the sunroof is lifted, lift the rear all the way and then close the sunroof. Have the system checked by an expert immediately.
Sunroof relearning WARNING The anti-trap function is not active during this procedure. Make sure that there are no obstacles in the way of the closing sunroof. In case the sunroof no longer closes properly, follow this relearning procedure: • •
•
Tilt the rear of the sunroof as far as possible. Release the button. Press and hold the same button again for 30 seconds until you see the sunroof move. Release the button and immediately press and hold it again. The sunroof will close, open fully and then close again. Do not release the button before the sunroof has reached the closed position for the second time.
If the button is not pressed continuously, the relearning function will be interrupted. Start the procedure once more from the beginning.
104
Seats •
SITTING IN THE CORRECT POSITION
• •
hold the steering wheel with your arms slightly bent. bend your legs slightly so that you can press the pedals fully. position the shoulder strap of the seat belt over the centre of your shoulder and position the lap strap tightly across your hips.
Make sure that your driving position is comfortable and that you can maintain full control of your vehicle.
MANUAL SEATS All vehicles E68595
WARNINGS Do not use any accessory seat covers that are not specifically designed for seats with side airbags. These seat covers must be fitted by properly trained technicians.
WARNINGS Do not adjust the seats when the vehicle is moving. Only when you use the seat belt properly, can it hold you in a position that allows the airbag to achieve its optimum effect.
Do not adjust the seats while the vehicle is moving.
When you use them properly, the seat, head restraint, seat belt and airbags will provide optimum protection in the event of a collision. We recommend that you: • • •
•
sit in an upright position with the base of your spine as far back as possible. do not recline the seatback more than 30 degrees. adjust the head restraint so that the top of it is level with the top of your head and as far forwards as possible, remaining comfortable. keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 250 millimetres (10 inches) between your breastbone and the airbag cover.
105
Seats Moving the seats forwards or backwards
Adjusting the height of the driver’s seat
E70730
Each pull or press on the lever will raise or lower the height by a small amount.
E70728
Adjusting the angle of the seatback
Pull the lever. Rock the seat to engage the catch. Adjusting the lumbar support
E70731
When the seats are slid fully forward the seatbacks can be fully reclined.
E78058
106
Seats ELECTRIC SEATS 2-way electric seat
E78059
107
Seats 6-way electric seat
E78060
108
Seats HEAD RESTRAINTS
WARNINGS When folding the seatbacks up, make sure that the belts are visible to an occupant and not caught behind the seat.
Adjusting the head restraint WARNINGS Raise the rear head restraint when the rear seat is occupied by a passenger.
Folding the rear seatbacks forwards
When using a forward facing child restraint on a rear seat, always remove the head restraint from that seat.
E66539 E78819
Adjust the head restraint so that the top of it is level with the top of your head.
Insert the seatbelt tongues into the retaining slots.
Removing the head restraint
Note: Focus RS does not have a centre head restraint.
Press the locking buttons and remove the head restraint.
Lower the head restraints. See Head restraints (page 109).
REAR SEATS WARNINGS When folding the seatbacks down, take care not to get your fingers caught between the seatback and seat frame. Make sure that the seats and the seatbacks are secure and fully engaged in their catches.
109
Seats Fold the seatback(s) forwards. Note: When the red marking in the unlocking button is visible, the seatback is not fully engaged. Release the seatback and repeat the procedure until the red marking is no longer visible.
HEATED SEATS CAUTION Operating this function with the engine off will drain the battery. The heated front seats are operated by rotary controls in the instrument panel. For item location: See Quick start (page 8).
E78820
Push the unlocking button on the seatback and fold the seatback forwards.
The maximum temperature is reached after five or six minutes. It is regulated thermostatically.
Folding the seat cushions and seatback forwards
The seat heating will operate only when the ignition is in position II.
E78821
Insert the seatbelt tongues into the retaining slots. Insert your fingers between the seat cushion and seatback and fold the seat cushion forwards. Lower the head restraints. See Head restraints (page 109).
110
Convenience features Note: You can use the socket to power 12 volt appliances that have a maximum current rating of 15 Amperes. Use only Ford accessory connectors or connectors specified for use with SAE standard sockets.
SUN BLINDS
E72972
E78057
Pull the sun blind up and attach it to the hooks.
Press the element in to use the cigar lighter. It will pop out automatically.
INSTRUMENT LIGHTING DIMMER
ASHTRAY
E78812
To empty, pull out the complete ashtray. E70454
CIGAR LIGHTER CAUTIONS If you use the socket when the engine is not running, the battery may discharge.
E78837
Do not hold the cigar lighter element pressed in.
Pull the cover to open. To empty, gently pull up on the open lid and extract the complete ashtray.
111
Convenience features AUXILIARY POWER SOCKETS
CAUTIONS If the LED flashes 3 or 4 times, have the system checked by a properly trained technician.
CAUTION If you use the socket when the engine is not running, the battery may discharge.
Note: You can use the socket to power 230 volt appliances that have a maximum rating of 150 watts.
Note: You can use the socket to power 12 volt appliances that have a maximum current rating of 10 Amperes. Use only Ford accessory connectors or connectors specified for use with SAE standard sockets.
E98199
E78056
Auxiliary power sockets are located in the centre console and in the luggage compartment.
CUP HOLDERS
Power inverter CAUTIONS If you use the socket when the engine is not running, the battery may discharge. If the LED flashes continuously, re-insert the plug or switch the ignition off and then on again.
E78838
WARNING
It will switch off if the temperature is above 85°C (185°F). The LED will flash once. When it has cooled down it will switch back on automatically.
To avoid scalding, never place hot drinks in the cup holder.
Do not exceed the maximum power output. If you do, the LED will flash twice. Remove the plug and re-insert it.
112
Convenience features Mobile phone cradle
GLOVE BOX Cooled glove box
E78840 E78839
Cup holders
The glove box can be cooled using air from the air conditioning system. When the air conditioning is switched on, the air flow entering the glove box will be cooled. If the air conditioning is switched off, the air flow will be at approximately ambient temperature.
See Cup holders (page 112).
Armrest
The air flow can be shut off to prevent the flow of cooled air into the vehicle interior. To turn the air flow on or off, turn the valve in the glove box.
CENTRE CONSOLE Depending on the equipment fitted, the following features may be incorporated into the console in your vehicle: E78841
Cigar lighter See Cigar lighter (page 111).
Ashtray See Ashtray (page 111).
Auxiliary power socket See Auxiliary power sockets (page 112).
113
Convenience features STORAGECOMPARTMENTS Front storage compartment
E78842 E78843
Storage compartments are incorporated into and under the armrest.
WARNING Never drive with the front storage compartment lid open. This will obscure your vision out of the windscreen. Before setting off, always ensure that the lid is securely engaged.
Storage compartment
Note: Avoid keeping heat-sensitive objects and liquids in the front storage compartment. Pull to open. To close, push the lid down until it engages. E78844
WARNING Do not use the storage compartment as an ashtray.
114
Convenience features REAR SEAT ARMREST
TOLL READER
E78729
On vehicles with an anti-heat windscreen, toll readers should be placed in the area as shown (all measurements shown in millimetres), otherwise communication performance with toll stations may be reduced. E78845
The toll reader should be placed on the passenger side to prevent the reader from obscuring the driver’s vision (e.g. at traffic lights).
GLASSES HOLDER
CD CHANGER This is located under the front passenger seat.
AUXILIARY INPUT (AUX IN) SOCKET The AUX IN socket is located in the glove compartment. See separate handbook.
E75193
115
Convenience features USB PORT
E97793
See separate audio handbook.
116
Starting the engine GENERAL INFORMATION
IGNITION SWITCH
General points on starting If the battery has been disconnected the vehicle may exhibit some unusual driving characteristics for approx. 8 kilometres (5 miles) after reconnecting the battery. This is because the engine management system must realign itself with the engine. Any unusual driving characteristics during this period may be disregarded.
Starting the engine by towing or pushing WARNING To prevent damage you must not push or tow start your vehicle. Use booster cables and a booster battery. See Using booster cables (page 186). E78086
A
Vehicles without the key free system
B
Vehicles with the key free system
Ignition switch positions Position 0 WARNING Never return the key to the 0 position when the vehicle is in motion. Ignition off. Position I Steering unlocked. Ignition and all main electrical circuits are disabled. The ignition key should not be left in this position for too long to avoid discharging the battery.
117
Starting the engine Positon II
Cold or hot engine
Ignition switched on, all electrical circuits operational. Warning and indicator lamps illuminate. This is the key position when driving, and must also be selected when being towed.
All vehicles CAUTION
Starter motor activated. Release the key as soon as the engine starts.
When the temperature is below -20ºC (-4ºF), switch the ignition on for at least one second before starting the engine. This will make sure that the maximum fuel pressure is established for starting the engine.
STEERING WHEEL LOCK
Vehicles with manual transmission
Postion III
Note: Do not touch the accelerator pedal.
WARNING Always check that the steering is unlocked before attempting to move your vehicle.
1. Fully depress the clutch pedal. 2. Start the engine. Vehicles with automatic transmission
Vehicles without keyless starting
Note: Do not touch the accelerator pedal.
To activate the steering wheel lock; 1.
Remove the key from the ignition switch. 2. Turn the steering wheel.
1. Select park or neutral. 2. Fully depress the brake pedal. 3. Start the engine.
Vehicles with keyless starting
All vehicles
Your vehicle has an electronically controlled steering wheel lock. This operates automatically.
If the engine does not start within 15 seconds, wait for a short period and try again.
The steering wheel lock is activated if the ignition is off, the engine not running and your vehicle is stationary.
If the engine does not start after three attempts, wait 10 seconds and follow the Flooded engine procedure.
The steering wheel lock is deactivated when the ignition is switched on.
If you have difficulty starting the engine when the temperature is below -25ºC (-13ºF), press the accelerator pedal between ¼ to ½ of its travel and try again.
STARTING A PETROL ENGINE
Flooded engine Vehicles with manual transmission
Note: You can only operate the starter for a maximum of 30 seconds at a time.
1.
118
Fully depress the clutch pedal.
Starting the engine Starting at low ambient temperatures
2. Fully depress the accelerator pedal and hold it there. 3. Start the engine.
When the temperature is lower than -10°C (14°F) and the vehicle is filled with E85, an engine block heater should be used to facilitate starting. See Engine heater (page 123). Failure to do this will result in a non start.
Vehicles with automatic transmission 1. Select park or neutral. 2. Fully depress the accelerator pedal and hold it there. 3. Fully depress the brake pedal. 4. Start the engine.
If the temperature is expected to remain below -10°C (14°F), it is recommended that you increase the proportion of petrol in the tank by topping up with 95 octane unleaded petrol if the tank is not already full. About 10 litres (2.2 gallons) of petrol will reduce the proportion of E85 in a ¾ full tank from 85% to 70% and will considerably improve cold start capability.
All vehicles If the engine does not start, repeat the Cold or hot engine procedure.
Engine idle speed after starting
If, at very low temperatures, the tank is filled with only E85 and there is no way to use an engine block heater, you may experience difficulties starting the engine.
The speed at which the engine idles immediately after starting will vary depending on the engine temperature.
If the engine fails to start, proceed as follows:
If the engine is cold then the idle speed will automatically be increased in order to heat the catalytic converter as quickly as possible. This ensures that vehicle emissions are kept to an absolute minimum.
1. Fully depress the accelerator pedal. 2. Turn the ignition key to position III. CAUTION
The idle speed will slowly decrease to the normal level as the catalytic converter warms up.
Release the ignition key as soon as the engine has started. 3. Gradually release the accelerator pedal after 5 seconds of engine cranking or as the engine speed rises.
STARTING A PETROL ENGINE - E85
If the engine fails to start, repeat steps 1, 2 and 3, or connect an engine block heater for two hours before attempting another start.
For general information on starting a petrol engine. See Starting a petrol engine (page 118).
During starting, the fuel injectors are turned off as long as the accelerator pedal is depressed. This can be used to drain excessive fuel from the intake manifold after several unsuccessful starting attempts.
119
Starting the engine Vehicles with a manual transmission
If the battery has been disconnected or after the fuel type has been changed, the idle speed may be irregular. This will improve after 10 to 30 seconds.
Note: If the clutch pedal is not depressed, a message appears in the information display.
STARTING A DIESEL ENGINE
Depress the clutch pedal.
Cold/hot engine
Vehicles with an automatic transmission
Depress the clutch pedal without touching the accelerator.
Note: If the brake pedal is not depressed, a message appears in the information display.
Turn the key to position II and ensure the glow plug indicator lamp illuminates.
Depress the brake pedal.
Wait until the lamp extinguishes before starting and continue cranking without pausing until the engine starts.
All vehicles Push the ignition switch in and turn it to switch on the ignition and to start the engine.
If the engine stalls, repeat the full starting procedure.
Once the system recognizes a passive key, the engine can be started. If no passive key is detected, PASSIVE KEY NOT DETECTED will appear in the information display.
At temperatures below -15 ºC it may be necessary to operate the starter for up to 30 seconds. If these weather conditions persist, an engine block heater is recommended.
Starting the engine with a spare key
Vehicles with the key free system
E78301
Assemble the spare key. See Keyless entry (page 37). Insert the spare key into the ignition switch.
E78300
120
Starting the engine Push the ignition switch in and turn it to switch on the ignition and to start the engine.
2. Fully depress the brake pedal. 3. Press the start button.
Starting with manual transmission
KEYLESS STARTING
Note: Releasing the clutch pedal during engine start will stop the engine cranking and return to ignition on.
WARNINGS The keyless starting system may not function if the key is close to metal objects or electronic devices such as mobile phones.
1. Fully depress the clutch pedal. 2. Press the start button.
Always check that the steering wheel lock is deactivated before attempting to move your vehicle. See Steering wheel lock (page 118).
Starting a diesel engine Note: Engine cranking may not commence until the engine glow plug cycle has been completed. This may take several seconds in extremely cold conditions.
Note: A valid passive key must be located inside the vehicle to switch the ignition on and start the engine.
Note: Continue to press the clutch or brake pedal until engine cranking begins.
Note: To start your engine you must also fully depress the brake or clutch pedal, depending on the transmission fitted.
Failure to start The passive starting system will not function if: • The passive key frequencies are jammed. • The passive key battery is flat. If you are unable to start your vehicle carry out the following procedure.
E85766
Ignition on Press the start button once. All electrical circuits are operational, warning lamps and indicators illuminate.
Starting with automatic transmission Note: Releasing the brake pedal during engine start will stop the engine cranking and return to ignition on. 1.
Make sure the transmission is in P or N.
121
Starting the engine Type 1
E85767
2. Insert the key into the key holder. 3. With the key in this position you can use the start button to switch the ignition on and start your vehicle.
E87382
1.
Hold the key next to the steering column shroud exactly as shown. 2. With the key in this position you can use the start button to switch the ignition on and start your vehicle.
Stopping the engine When your vehicle is stationary, press the start button to stop the engine. The ignition, all electrical circuits, warning lamps and indicators will be switched off.
Type 2
DIESEL PARTICULATE FILTER (DPF) The DPF forms part of the emissions reduction systems fitted to your vehicle. It filters harmful diesel particulates (soot) from the exhaust gas.
E87381
1.
Carefully prise out the cover.
122
Starting the engine Regeneration
SWITCHING OFF THE ENGINE
WARNING Do not park or idle your vehicle over dry leaves or dry grass or other combustible material. The regeneration process requires very high exhaust gas temperatures and the exhaust will radiate a considerable amount of heat during and after regeneration, and after you have switched the engine off. This is a potential fire hazard.
Vehicles with a turbocharger
Unlike a normal filter which requires periodic replacement, the DPF has been designed to regenerate, or clean itself to maintain operating efficiency. The regeneration process takes place automatically. However, some driving conditions mean that you may need to support the regeneration process.
Release the accelerator pedal. Wait until the engine has reached idle speed and then switch it off.
CAUTION Do not switch the engine off when it is running at high speed. If you do, the turbocharger will continue running after the engine oil pressure has dropped to zero. This will lead to premature turbocharger bearing wear.
ENGINE HEATER CAUTION Make sure you disconnect the power cable from the engine heater connector before driving away.
If you drive only short distances or your journeys contain frequent stopping and starting, occasional trips with the following conditions could assist the regeneration process: •
• •
Note: The engine heater connector is located in the radiator grille at the front of your vehicle.
Drive your vehicle, preferably on a main road or motorway, for up to 20 minutes avoiding prolonged idling, but always observing speed limits and road conditions. Do not switch off the ignition. Use a lower gear than normal to maintain a higher engine speed during this journey, where appropriate.
E97918
Connect the engine heater for 2 to 3 hours before starting the engine.
123
Fuel and refuelling SAFETY PRECAUTIONS
CAUTIONS Do not use leaded petrol or petrol with additives containing other metallic compounds (e.g. manganese-based). They could damage the emission system.
WARNINGS Stop refuelling after the fuel nozzle stops the second time. Additional fuel will fill the expansion space in the fuel tank which could lead to fuel overflowing. Fuel spillage could be hazardous to other road users.
Do not use methanol instead of E85.
Do not use any kind of flames or heat near the fuel system. The fuel system is under pressure. There is a risk of injury if the fuel system is leaking.
Note: We recommend that you use only high quality fuel without additives or other engine treatments. Note: When using E85, you may experience a higher fuel consumption.
FUEL QUALITY - PETROL
Note: The correct fuel type for your vehicle is shown on a decal on the inside of the fuel filler flap.
Note: We recommend that you use only high quality fuel without additives or other engine treatments.
Note: Your vehicle will operate well on commercial quality 95 octane unleaded petrol, but only high quality E85 offers the same protection and performance.
CAUTION Do not use leaded petrol or petrol with additives containing other metallic compounds (e.g. manganese-based). They could damage the emission system.
Use minimum 95 octane unleaded petrol that meets the specification defined by EN 228, or equivalent. You can also use a mixture of unleaded petrol and E85.
Long-term storage
Use minimum 95 octane unleaded petrol that meets the specification defined by EN 228, or equivalent.
Due to small amounts of corrosive impurities that may be found in the E85, it is recommended that you fill the tank with only 95 octane unleaded petrol prior to long-term storage of your vehicle.
FUEL QUALITY - E85 WARNINGS Do not modify the fuel system configuration or the components in the system.
FUEL QUALITY - DIESEL Note: We recommend that you use only high quality fuel without additives or other engine treatments.
Do not replace the fuel system or the components with parts not specially designed to be used with E85.
124
Fuel and refuelling Parking
WARNING Do not mix diesel with oil, petrol or other liquids. This could cause a chemical reaction.
WARNING Do not park your vehicle over dry leaves or dry grass. The exhaust will continue to radiate a considerable amount of heat after you have switched the engine off. This is a potential fire hazard.
CAUTION Do not add kerosene, paraffin or petrol to diesel. This could cause damage to the fuel system.
FUEL FILLER FLAP Note: We do not recommend the prolonged use of additives intended to prevent fuel waxing.
WARNINGS Take care when refuelling to avoid spilling any residual fuel from the fuel pipe nozzle.
Use diesel that meets the specification defined by EN 590, or equivalent.
We recommend that you wait at least 10 seconds before removing the fuel pipe nozzle to allow any residual fuel to drain into the fuel tank.
You can use diesel that contains up to 5% RME (bio diesel).
CATALYTIC CONVERTER
CAUTION
Driving with a catalytic converter
If you use a high pressure spray to wash your vehicle, only spray the fuel filler flap briefly from a distance not less than 20 centimetres (8 inches).
CAUTIONS Avoid running out of fuel. Do not crank the engine for long periods. Do not run the engine when a spark plug lead is disconnected. Do not push-start or tow-start your vehicle. Use booster cables. See Using booster cables (page 186). Do not switch the ignition off when driving.
E86613
Open the flap fully until it engages.
125
Fuel and refuelling When you insert the fuel pump nozzle, a spring loaded inhibitor will open if the correct size nozzle is detected. This will prevent filling up with the wrong fuel.
REFUELLING - E85 CAUTION Do not attempt to start the engine if you have filled the fuel tank with the incorrect fuel. This could damage the engine. Have the system checked by a properly trained technician immediately. After refuelling, allow 5 minutes of normal engine operation above 48 km/h (30 mph) to reduce the risk of an increased engine restart time.
E107539
Insert the filler up to the first notch on the nozzle, and keep it in position on the fuel filler opening.
FUEL CONSUMPTION
A funnel is located in the glove box. Use this when refilling with a fuel can.
The CO2 and fuel consumption figures are derived from laboratory tests according to EEC Directive 80/1268/EEC and subsequent amendments and are carried out by all vehicle manufacturers.
REFUELLING CAUTION
They are intended as a comparison between makes and models of vehicles. They are not intended to represent the real world fuel consumption you may get from your vehicle. Real world fuel consumption is governed by many factors including; driving style, high speed driving, stop/start driving, air conditioning usage, the accessories fitted and towing etc.
Do not attempt to start the engine if you have filled the fuel tank with the incorrect fuel. This could damage the engine. Have the system checked by a properly trained technician immediately.
Your Ford dealer can give you advice on improving your fuel consumption.
126
Fuel and refuelling TECHNICAL SPECIFICATIONS Fuel consumption figures Urban
Extra-urban
Combined
CO2 emissions
l/100 km (mpg)
l/100 km (mpg)
l/100 km (mpg)
g/km
1.4L Duratec, Stage IV, 3door, 4-door, 5-door and Estate
8.6 (32.8)
5.3 (53.3)
6.5 (43.5)
155
1.6L Duratec, Stage IV, 3door, 4-door, 5-door and Estate, manual transmission
8.7 (32.5)
5.5 (51.4)
6.7 (42.2)
159
1.6L Duratec, Stage IV, 3door, Automatic transmission
10.4 (27.2)
5.9 (47.9)
7.5 (37.7)
180
1.6L Duratec, Stage IV, 4door, 5-door and Estate, automatic transmission
10.6 (26.6)
6.0 (47.1)
7.7 (36.7)
184
1.6L Duratec, Stage IV, convertible, manual transmission
9.4 (30.1)
5.8 (48.7)
7.1 (39.8)
169
1.6L Duratec Ti-VCT, Stage IV, 3-door, 4-door, 5-door and Estate
8.7 (32.5)
5.4 (52.3)
6.6 (42.8)
157
1.8L Duratec-HE, Stage IV, 3-door, 4-door, 5-door and Estate, manual transmission, (Flexfuel engine in petrol mode)
9.5 (29.7)
5.6 (50.4)
7.0 (40.4)
167
2.0L Duratec-HE, Stage III and IV, 3-door, 4-door, 5door and Estate, manual transmission
9.8 (28.8)
5.4 (52.3)
7.1 (39.8)
169
2.0L Duratec-HE, Stage IV, 3-door, 4-door, 5-door and Estate, Automatic transmission
11.2 (25.2)
6.1 (46.3)
8.0 (35.3)
189
Variant
127
Fuel and refuelling
Urban
Extra-urban
Combined
CO2 emissions
l/100 km (mpg)
l/100 km (mpg)
l/100 km (mpg)
g/km
2.0L Duratec-HE, Stage IV, convertible, manual transmission
10.6 (26.6)
5.7 (49.6)
7.5 (37.7)
179
2.5L Duratec-ST, Stage IV, 3-door and 5-door
13.8 (20.5)
6.8 (41.5)
9.3 (30.4)
224
2.5L Duratec-RS, Stage IV, 3-door
14 (20.2)
7.5 (37.7)
9.9 (28.5)
235
1.6L Duratorq-TDCi 66 kW (90 PS), Stage IV, 3-door, 4-door, 5-door and Estate
5.9 (47.9)
4.0 (70.6)
4.7 (60.1)
124
1.6L Duratorq-TDCi 80 kW (109 PS), Stage III and IV with a DPF, 3-door, 4-door, 5-door and Estate, manual transmission
6.2 (45.6)
4.0 (70.6)
4.8 (58.9)
127
1.6L Duratorq-(DV6) Econetic, 66 kW (90 PS), Stage IV, 3-door, 5-door and Estate, manual transmission
5.5 (51.4)
3.6 (78.5)
4.3 (65.7)
114
1.6L Duratorq-(DV6) Econetic, 80 kW (109 PS), Stage IV with a DPF, 3-door, 5door and Estate, manual transmission
5.6 (50.4)
3.6 (78.5)
4.3 (65.7)
115
1.8L Duratorq-TDCi, Stage IV, 3-door and 5-door
6.7 (42.2)
4.3 (65.7)
5.2 (54.3)
137
1.8L Duratorq-TDCi, Stage IV, 4-door and Estate
6.8 (41.5)
4.4 (64.2)
5.3 (53.3)
139
2.0L Duratorq-TDCi 100 kW (136 PS), Stage III, 3-door and 5-door
7.4 (38.2)
4.4 (64.2)
5.5 (51.4)
144
2.0L Duratorq-TDCi 100 kW (136 PS), Stage III, 4-door and Estate
7.5 (37.7)
4.5 (62.8)
5.6 (50.4)
148
Variant
128
Fuel and refuelling
Urban
Extra-urban
Combined
CO2 emissions
l/100 km (mpg)
l/100 km (mpg)
l/100 km (mpg)
g/km
2.0L Duratorq-TDCi 100 kW (136 PS), Stage IV, 3-door and 5-door
7.4 (38.2)
4.6 (61.4)
5.6 (50.4)
148
2.0L Duratorq-TDCi 100 kW (136 PS), Stage IV, 4-door and Estate
7.4 (38.2)
4.7 (60.1)
5.7 (49.6)
149
2.0L Duratorq-TDCi 100 kW (136 PS), Stage IV, convertible
7.7 (36.7)
4.9 (57.6)
5.9 (47.9)
156
Variant
129
Transmission Selector lever positions
MANUAL TRANSMISSION All vehicles CAUTIONS Do not engage reverse gear when the vehicle is moving. This can cause damage to the transmission. Do not apply any undue lateral force to the gear lever when changing from 5th to 4th gear. This could lead to the inadvertent selection of 2nd gear and can cause damage to the transmission.
E78310
Selecting reverse gear On some vehicles it is necessary to raise the collar whilst selecting reverse gear.
P
Park
R
Reverse
N
Neutral
D
Drive
M
Manual shifting WARNING Apply the brakes before moving the selector lever and keep them applied until you are ready to move
off. Note: A cold engine has a higher idle speed. This will increase the tendency for your vehicle to creep when you have selected a drive gear.
E99067
AUTOMATICTRANSMISSION
Press the button on the selector lever to select reverse and park.
General information
The selector lever position will be shown in the information display.
This transmission also allows you to change gear manually (similar to a manual transmission).
Park WARNINGS Select park only when your vehicle is stationary.
130
Transmission WARNINGS Apply the parking brake and select park before leaving your vehicle. Make sure that the selector lever is latched in position.
WARNING Do not hold the selector lever permanently in – or +. Gears can be skipped by moving the selector lever repeatedly at short intervals.
Note: An audible warning will sound if you open the driver's door and you have not selected park.
Manual mode also provides a kickdown function. See Kickdown. The transmission will automatically downshift when the engine speed is too low and upshift when to high.
Note: The battery saver will deactivate the warning chime after a period of time. In this position, power is not transmitted to the drive wheels and the transmission is locked. You can start the engine with the selector lever in this position.
Drive modes The transmission will select the appropriate gear for optimum performance based on ambient temperature, road gradient, vehicle load and driver input.
Reverse WARNING Select reverse only when your vehicle is stationary and the engine is at idle speed.
Hints on driving with an automatic transmission Moving off
Neutral
WARNING
In this position, power is not transmitted to the drive wheels but the transmission is not locked. You can start the engine with the selector lever in this position.
It is not possible to tow-start or push-start a vehicle fitted with an automatic transmission. See Using booster cables (page 186).
Drive 1. Release the parking brake. 2. Release the brake pedal and press the accelerator pedal.
Select drive to shift automatically through the forward gears. Manual shifting
Stopping
Note: A shift will occur only when the vehicle speed and the engine speed are appropriate.
1.
Release the accelerator pedal and press the brake pedal. 2. Apply the parking brake.
Select manual shifting to shift manually through the forward gears. Push the selector lever forwards to shift down and pull it backwards to shift up.
131
Transmission Kickdown Press the accelerator pedal fully with the selector lever in the drive position to select the next lowest gear for optimum performance. Release the accelerator pedal when you no longer require kickdown.
Emergency park position release lever E78322
Use the lever to move the selector lever from the park position in the event of an electrical malfunction or if your vehicle has a flat battery.
With a suitable object push down the locking lever in the slot and simultaneously move the selector lever out of the P position. Note: If position P is selected again, this procedure must be repeated.
E78321
CAUTION Take care when lifting up the hinged cover. Lift up the hinged cover in the centre console next to the selector lever with a small flat bladed tool.
132
Brakes PRINCIPLE OF OPERATION
PARKING BRAKE
Disc brakes
All vehicles
Wet brake discs result in reduced braking efficiency. Dab the brake pedal when driving from a car wash to remove the film of water.
WARNING Vehicles with an automatic transmission should always be left with the selector lever in position P.
ABS • •
WARNING The ABS does not relieve you of your responsibility to drive with due care and attention.
• •
The ABS helps you to maintain full steering and directional stability when you brake heavily in an emergency, by preventing the road wheels from locking.
•
HINTS ON DRIVING WITH ABS
Press the foot brake pedal firmly. Pull the parking brake lever up smartly to its fullest extent. Do not press the release button while pulling the lever up. If your vehicle is parked on a hill and facing uphill, select first gear and turn the steering wheel away from the kerb. If your vehicle is parked on a hill and facing downhill, select reverse gear and turn the steering wheel towards the kerb.
To release the parking brake, press the brake pedal firmly, pull the lever up slightly, depress the release button and push the lever down.
When the ABS is operating, the brake pedal will pulse. This is normal. Maintain pressure on the brake pedal. The ABS will not eliminate the dangers inherent when: • you drive too close to the vehicle in front of you. • the vehicle is aquaplaning. • you take corners too fast. • the road surface is poor.
133
Stability control PRINCIPLE OF OPERATION
Stability control (ESP) warning lamp
Electronic stability programme (ESP)
The ESP warning lamp will flash when the system is operating. See Warning lamps and indicators (page 78).
WARNING
Emergency brake assist
ESP does not relieve you of your responsibility to drive with due care and attention.
WARNING Emergency brake assist does not relieve you of your responsibility to drive with due care and attention. Emergency brake assist will detect when you brake heavily by measuring the rate at which you press the brake pedal. It will provide maximum braking efficiency as long as you press the pedal. Emergency brake assist can reduce stopping distances in critical situations.
B
B
USING STABILITY CONTROL
B A A
B
Note: The system will be switched on automatically every time you switch the ignition on.
A
Vehicles with stability control (ESP) switch
E72903
A
without ESP
B
with ESP
Note: On Focus RS, stability control (ESP) is only reduced and not switched off completely. Press and hold the switch for one second. The switch will illuminate. A message will be shown in the display. See Information messages (page 89).
The ESP supports stability when the vehicle starts to slide away from your intended path. This is performed by braking individual wheels and reducing engine torque as needed.
Press the switch again to turn the system on.
The system also provides an enhanced traction control function by reducing engine torque if the wheels spin when you accelerate. This improves your ability to pull away on slippery roads or loose surfaces, and improves comfort by limiting wheel spin in hairpin bends.
For item location: See Quick start (page 8).
Vehicles without stability control (ESP) switch To turn the system off and on. See Information displays (page 82).
134
Parking aid PRINCIPLE OF OPERATION
USING THE PARKING AID
WARNING The parking aid does not relieve you of your responsibility to drive with due care and attention. CAUTIONS The sensors may not detect objects in heavy rain or other conditions that cause disruptive reflections.
E77927
The sensors may not detect objects with surfaces that absorb ultrasonic waves.
CAUTIONS Vehicles fitted with a trailer tow module not approved by us may not correctly detect obstacles.
The sensors may not detect objects that are close to the vehicle (approximately 30 centimetres [11 inches] to the rear and above or below the sensors).
Take particular care when reversing with a tow ball arm or rear fitted accessories e.g. a bicycle carrier, as the rear parking aid will only indicate the distance from the bumper to the obstacle.
If you use a high pressure spray to wash your vehicle, only spray the sensors briefly from a distance not less than 20 centimetres (8 inches).
The parking aid does not detect obstacles moving away from the vehicle. They will only be detected shortly after they start to move towards the vehicle again.
Note: The parking aid may emit false tones if it detects a signal using the same frequency as the sensors or if the vehicle is fully laden.
Note: On vehicles fitted with a tow ball arm, the parking aid is deactivated automatically when any trailer lamps (or lighting boards) are connected to the 13-pin socket via a trailer tow module we have approved.
Note: The outer sensors may detect the side walls of a garage. If the distance between the outer sensor and the side wall remains constant for three seconds, the tone will switch off. As you continue, the inner sensors will detect rearward objects.
Note: Keep the sensors free from dirt, ice and snow. Do not clean with sharp objects. Note: On vehicles fitted with automatic transmission, the parking aid will not operate in position P. The parking aid is automatically activated when you select reverse gear with the ignition switched on.
135
Parking aid You will hear an intermittent tone at a distance of up to 180 centimetres between the obstacle and rear bumper and 60 centimetres to the side. Decreasing the distance accelerates the intermittent tone. A continuous tone will start at a distance of less than 30 centimetres. Note: If a high pitch tone is heard for three seconds, this indicates a malfunction. The system will switch off automatically if it malfunctions. Have this checked as soon as possible.
Convertible only CAUTION Do not open the convertible top in confined spaces. This could cause damage to the luggage compartment lid. See Convertible top (page 147). You will hear a continuous warning tone when you operate the convertible roof if an object is detected less than 30 centimetres from the rear bumper.
136
Cruise control Setting a speed
PRINCIPLE OF OPERATION Cruise control allows you to control your speed using the switches on the steering wheel. You can use cruise control when you exceed approximately 30 km/h (20 mph).
USING CRUISE CONTROL WARNING Do not use cruise control in heavy traffic, on twisty roads or when the road surface is slippery. E75452
Switching cruise control on
Press to store and maintain your current speed. The cruise control indicator will illuminate. See Warning lamps and indicators (page 78).
Changing the set speed WARNING When you are going downhill, your speed may increase above the set speed. The system will not apply the brakes. Change down a gear and press the SET- switch to assist the system in maintaining the set speed. E75456
Note: If you accelerate by pressing the accelerator pedal, the set speed will not change. When you release the accelerator pedal, you will return to the speed that you previously set.
Note: The system is ready for you to set a speed.
137
Cruise control Resuming the set speed
A B
E95393
A
Accelerate
E75453
B
Decelerate
The cruise control indicator will illuminate and the system will attempt to resume the speed that you previously set.
Cancelling the set speed
Switching cruise control off
E75453
Press the brake pedal or the RES switch.
E75455
Note: The system will no longer control your speed. The cruise control indicator will not illuminate but the system will retain the speed that you previously set.
The system will not retain the speed that you previously set. The cruise control indicator will not illuminate.
138
Load carrying GENERAL INFORMATION
LUGGAGE COVERS
WARNINGS Use load securing straps to an approved standard, e.g. DIN.
WARNING Do not place objects on the luggage cover.
Make sure that you secure all loose items properly.
3-door and 5-door
Place luggage and other loads as low and as far forward as possible within the luggage or loadspace.
1
Do not drive with the tailgate or rear door open. Exhaust fumes may enter the vehicle. Do not exceed the maximum front and rear axle loads for your vehicle. See Vehicle identification (page 204).
2
Heavy loads, when placed in the passenger compartment, should be on folded rear seats as shown. See Rear seats (page 109).
E72512
Estate
E72969
E97377
Pull out the cover and secure it in the retaining points. Release it from the retaining points and let it roll back into the case. Clip the retaining hook onto the case.
139
Load carrying Ensure that the end caps with the anti-rotation pin are correctly fitted in the side trim.
E72970
REAR UNDER FLOOR STORAGE 3-door and 5-door with full-size spare wheel
E78834
Pull up the net and insert the ends of the bar into the retainers on the roof. Ensure that the bar is pushed forwards into the narrow section of the retainers. WARNING
E78846
After installing the cassette, press the front edge of the luggage cover back down into its original position (forwards) to prevent vision out of the rear screen being obscured.
To gain access to the storage areas, raise the carpet.
CARGO NETS Cargo retention net
Reinstall the luggage cover.
To install the cargo retention net cassette:
Remove in the reverse order.
Remove the luggage cover. Push the sliders on the cassette towards each other and insert the telescopic bar into the holes on the sidewall behind the rear seatbacks.
140
Load carrying Cargo net
E78836
Note: Access to the net is possible from the rear seats by folding back the front of the luggage cover.
E78835
A
With retaining rings
B
Without retaining rings
The net can also be hung on the sidewalls. Fold the net in half and press together the Velcro strips on the sides of the net. Attach the loops at the top of the net to the hooks on the sidewall and the hooks at the bottom to the retaining points on the floor.
The cargo net can be used to prevent objects sliding around. Attach the hooks at each corner of the net to the four retaining points on the load floor.
ROOF RACKS AND LOAD CARRIERS Roof rack WARNINGS Do not fit a roof rack to vehicles with a convertible top.
141
Load carrying Note: Position the crossbars as shown.
WARNINGS If you use a roof rack, the fuel consumption of your vehicle will be higher and you may experience different driving characteristics.
A
Read and follow the manufacturer’s instructions when you are fitting a roof rack.
B
E98206
CAUTION
A
95 mm
Do not exceed the maximum permissible roof load of 75 kilogrammes (165 pounds) (including the roof rack).
B
800 mm
Check the security of the roof rack and tighten its fittings as follows: • • •
before starting after driving 50 kilometres (30 miles) at 1 000 kilometres (600 miles) intervals.
2 1
E98207
Installing the crossbars
1. Pull the handle out. 2. Turn the handle clockwise to bring the crossbar in contact with the rail.
WARNING Distribute the load evenly over the loading area and keep the centre of gravity as low as possible. Secure the load well to prevent it from slipping. Never place any loads directly onto the roof surface.
A CAUTION Remove the crossbars before entering an automatic car wash. Note: The side mounting tracks are designed such that crossbars (for bicycle carriers, ski carriers etc.) from the Ford accessories range can be fitted.
3 E98222
Note: Make sure there is no gap between crossbar and rail (A).
Note: Before installing the crossbars, clean the side mounting tracks with water and a sponge.
142
Load carrying 3. Turn the handle a minimum of 3.5 revolutions.
E98208
4. Push the handle in. Turn the key clockwise to lock. 5. Remove the key. Accessing the T-notch
3
1 2 E98209
1. Pull the handle out. 2. Lower the cover. 3. Remove the sliding bar.
143
Towing TOWING A TRAILER
DETACHABLE TOW BALL
WARNINGS Do not exceed the maximum vehicle and trailer weight stated on the vehicle identification plate. See Vehicle identification plate (page 204).
WARNINGS When not in use, always transport the tow ball arm securely fastened in the luggage compartment. Take special care when fitting the tow ball arm as the safety of the vehicle and the trailer depends on
Focus ST and Focus RS are not approved for trailer towing. this.
Do not use any tools for mounting or dismounting the tow ball arm. Do not modify the trailer coupling. Do not disassemble or repair the tow ball arm.
Note: Not all vehicles are suitable or approved to have tow bars fitted. Check with your dealer first. Place loads as low and central to the axle(s) of the trailer as possible. If you are towing with an unladen vehicle, the load in the trailer should be placed toward the nose, within the maximum nose load, as this gives the best stability. Note: The maximum trailer nose weight can be found in the original vehicle documents (confirmation of conformity). Alternatively refer to your dealer. The stability of the vehicle to trailer combination is very much dependant on the quality of the trailer.
E71328
In high altitude regions above 1 000 metres (3 281 feet), the stipulated maximum permitted gross train weight must be reduced by 10% for every additional 1 000 metres (3 281 feet).
Unlocking the tow ball arm mechanism
Steep gradients WARNING The overrun brake on a trailer is not controlled by ABS.
2
Change down a gear before you reach a steep downhill gradient.
1 E99477
144
Towing 1. Detach the keyhole protective cap. 2. Insert the key and turn it anti-clockwise to unlock (1). 3. Hold the tow ball arm. Pull the handwheel out and turn it clockwise until it clicks (2). 4. The red mark on the handwheel must align with the white mark on the tow ball. 5. Release the handwheel. The tow ball arm is unlocked.
3. The green mark on the handwheel must align with the white dot on the tow ball. 4. To lock, turn the key clockwise and remove the key (3). 5. Attach the keyhole protective cap.
Driving with a trailer
Inserting the tow ball arm
A
WARNING The tow ball arm may only be inserted when completely unlocked.
B
E71331 WARNING
If any of the below conditions cannot be met, do not use the tow bar and have it checked by a properly trained technician.
1
Before starting your journey, make sure that the tow ball arm is properly locked. Check:
2
•
•
3
• • E99484
1. Pull out the plug (1). 2. Insert the tow ball arm vertically and press it upwards until it engages (2). Do not hold your hand near the handwheel.
145
The green mark on the handwheel is aligned with the white dot on the tow ball arm. the handwheel (A) is correctly fitted to the tow ball arm. you have removed the key (B). the tow ball arm is securely positioned. It must not move when jerked.
Towing Removing the tow ball arm
Maintenance
WARNING
WARNING
Never unlock the tow ball arm with the trailer attached.
Remove the tow ball arm and protect the seat with the plug before steam cleaning your vehicle. Keep the system clean. Periodically lubricate bearings, sliding surfaces, and locking balls with resin-free grease or oil and the lock with graphite. Keep a note of the key number. In case of loss, replacement keys are available from the manufacturer by stating the three digit key number.
4
3 1
E99485
2
1. Unhitch the trailer. 2. Detach the keyhole protective cap. 3. Insert the key and turn it anti-clockwise to unlock (1). 4. Hold the tow ball arm. Pull the handwheel out, turn it clockwise against the stop (2) and remove the tow ball arm (3). 5. Release the handwheel. When unlocked in this way, the tow ball arm can be reinserted at any time. Insert the plug into its seat (4).
146
Convertible top OPENING THE CONVERTIBLE TOP
CAUTIONS Do not clean the convertible top with a high pressure spray.
Convertible top operating clearance
Note: The convertible top cannot be opened if the vehicle is moving. Note: The convertible top will lock and unlock automatically. Note: The front windows and rear quarter windows will move automatically.
A
1.
Move the luggage separator to the fully deployed position.
2. Switch the ignition to position II.
B
E77958
A
2050 millimetres (80.7 inches)
B
190 millimetres (7.5 inches)
WARNINGS Make sure that there are no obstructions in the convertible top linkage area, windscreen frame, door windows and rear quarter windows before opening or closing the convertible top.
E77959
Note: If you keep the convertible top switch pressed, after the convertible top has fully opened, the front windows and rear quarter windows will automatically return to the fully closed position.
Keep the areas around the rollover bar covers free from obstruction. CAUTIONS Do not operate the convertible top when the temperature is below -5°C.
3. Press and hold the convertible top switch until the convertible top is fully open. A chime will be heard.
Make sure that the luggage separator is correctly located in the deployed position. Do not OPEN the convertible top manually. This could damage the linkage mechanism.
147
Convertible top Luggage separator
CAUTIONS Do not move the front seats fully rearwards with the wind deflector installed.
CAUTIONS Do not place luggage items on top or to the sides of the luggage separator. This could damage the luggage separator or the convertible top.
Do not place luggage items on top of the wind deflector. Do not place large objects underneath the wind deflector.
Do not place large objects underneath the luggage separator. This could damage the convertible
Do not place loose objects under the wind deflector.
top. Note: The luggage separator prevents items from moving into the area in which the convertible top is stowed. Note: The convertible top will not open until the luggage separator is in the fully deployed position.
2 E88448
1.
Open out the wind deflector.
1 E77960
1. Pull the luggage separator. 2. Slide the locating lugs into the sliders on either side of the luggage compartment to close the proximity switch.
E88449
2. Unfold the wind deflector.
Wind deflector WARNING Do not allow passenger's to travel in the rear of the vehicle with the wind deflector installed.
148
Convertible top Manual closure of the convertible top WARNINGS Two people are required when closing the convertible top, one either side. The convertible top must be moved evenly. Do not drive with the luggage compartment lid locking levers unlocked.
E78180
3. Fit the supports into the rear seat belt openings.
1.
Open the luggage compartment lid.
E78181
4. Pull the levers back, against spring pressure, and release to engage in the catches. E78025
CLOSING THE CONVERTIBLE TOP
2. Remove the convertible top headliner plug.
Note: The convertible top cannot be closed if the vehicle is moving. Note: The front windows and rear quarter windows will close automatically. 1.
Switch the ignition to position II. 2. Press and hold the convertible top switch until the convertible top is fully closed. A chime will be heard.
149
Convertible top
E78026
E88100
3. Use the Allen key and unlock the convertible top locking lever.
7. Pull the luggage compartment lid locking lever release cable on both sides, to release the convertible top.
5
4
6
E88101
4. Partially peel off the luggage compartment weatherstrip on both sides. 5. Remove the luggage compartment carpet retaining clip on both sides. 6. Pull the luggage compartment carpet away slightly on both sides.
E78029
8. Raise the luggage compartment lid.
150
Convertible top
E78030
E88444
Note: The tonneau cover will raise with the convertible top.
12. 13.
9. Close the convertible top.
Lower the luggage compartment lid. Open the luggage compartment lid from the rear.
E78028
14. 15.
E78031
10. 11.
Use the Allen key and lock the convertible top locking lever. Install the convertible top headliner plug.
16. 17.
151
Lock the luggage compartment lid locking levers. Refit the luggage compartment carpet on both sides. Install the luggage compartment carpet retaining clip on both sides. Refit the luggage compartment weatherstrip on both sides.
Convertible top 18.
Close the luggage compartment lid.
152
Driving hints In an emergency, the vehicle can be driven through water to a maximum depth of 200 mm and at a maximum speed of 10 km/h (6 mph). Extra caution should be exercised when driving through flowing water.
RUNNING-IN Tyres WARNING New tyres need to be run-in for approximately 500 kilometres (300 miles). During this time, you may experience different driving characteristics.
When driving in water, maintain a low speed and do not stop the vehicle. After driving through water, and as soon as it is safe to do so: • Depress the brake pedal lightly and check that full brake function is achieved. • Check that the horn works. • Check that the vehicle's lights are fully operational. • Check the power assistance of the steering system.
Brakes and clutch WARNING Avoid heavy use of the brakes and clutch if possible for the first 150 kilometres (100 miles) in town and for the first 1 500 kilometres (1 000 miles) on motorways.
Engine CAUTION Avoid driving too fast during the first 1 500 kilometres (1 000 miles). Vary your speed frequently and change up through the gears early. Do not labour the engine.
DRIVING THROUGH WATER Driving through water CAUTIONS Drive through water in an emergency only, and not as part of normal driving. Engine damage can occur if water enters the air filter.
153
Emergency equipment FIRST AID KIT
WARNING TRIANGLE
3-door and 5-door
3-door and 5-door
E78856
E78859
4-door
4-door
E78857
E78860
Estate
Estate A storage area for a warning triangle is located under the carpet.
E78858
154
Status after a collision •
FUEL CUT-OFF SWITCH Vehicles with a Duratec engine
•
Turn the ignition switch to position II. After a few seconds return the key to position I. Make a further check for leaks in the fuel system.
INSPECTING SAFETY SYSTEM COMPONENTS Seat belts Belts subjected to strain, as a result of an accident, should be renewed and the anchorages checked by a properly trained technician.
E72531
The fuel supply may be cut off as a result of an accident or sudden vibrations (e.g. collision when parking). The switch is located in the side panel in front of the driver's door. Resetting the switch WARNING Do not reset the fuel cut-off switch if you see or smell leaking fuel. • • •
Turn the ignition switch to position 0. Check fuel system for leaks. If no fuel leak is apparent, reset the switch by pushing in the button (see illustration).
155
Fuses FUSE BOX LOCATIONS
Install in the reverse order.
Engine compartment fuse box
CHANGING A FUSE WARNINGS Do not modify the electrical system of your vehicle in any way. Have repairs to the electrical system and the replacement of relays and high current fuses carried out by properly trained technicians. Switch the ignition and all electrical equipment off before touching or attempting to change a fuse. CAUTION
E78332
Fit a replacement fuse with the same rating as the one you have removed.
Passenger compartment fuse box
Note: You can identify a blown fuse by a break in the filament.
1.
Remove the screws in the instrument panel trim underneath the glove compartment and lower the trim panel. 2. Loosen the screws. 3. Lower the fuse box and pull it towards you.
Note: All fuses, except high current fuses are a push fit. Note: A fuse puller is located in the lid of the engine compartment fuse box.
Luggage compartment auxiliary power socket (vehicles with trailer tow module)
120
20
Door module, right-hand rear
121
20
Heated front seats
122
10
Airbag module
123
7.5
Heated exterior mirrors
124
7.5
Parking lamps, side lamps, tail lamps (left-hand side)
125
7.5
Parking lamps, side lamps, tail lamps (right-hand side)
126
20
Keyless system Electric windows
127
25
128
-
129
20
130
-
Not used Windscreen wipers Not used
131
15
Rear window wiper
132
15
Brake lamps
133
25
Central locking relays, passenger door module
134
20
Central locking, driver door module
135
20
Daytime running lamps
136
15
Washer pump, heated washer jets
137
10
Battery backup sounder
161
Fuses Fuse
Ampere rating
Circuits protected
138
10
Powertrain control module, accelerator pedal, automatic transmission
139
10
Main beam right-hand side
140
10
Main beam left-hand side
141
10
Reversing lamp, electric mirrors
142
15
Dipped beam, right-hand side
143
15
Dipped beam, left-hand side
162
Vehicle recovery Rear towing eye
TOWING POINTS Front towing eye
E78368
A
E91637
Mount for rear towing eye
Towing eye location The screw-in towing eye is located in the spare wheel well. Insert your finger into the hole on the underside of the cover and prise off the cover. Install the towing eye. The towing eye must always be carried in the vehicle. CAUTION The screw-in towing eye has a left-hand thread. Turn it anti-clockwise to install it. Note: On vehicles with a tow bar, the towing eye cannot be installed at the rear of the vehicle. Use the tow bar to tow a vehicle.
E78367
163
Vehicle recovery TOWING THE VEHICLE ON FOUR WHEELS
CAUTIONS Do not tow your vehicle backwards.
All vehicles
Select neutral when your vehicle is being towed.
WARNINGS Switch the ignition on when your vehicle is being towed. The steering lock will engage and the direction indicators and brake lamps will not work if you do not. The brake servo and the power steering pump do not operate unless the engine is running. Press the brake pedal harder and allow for increased stopping distances and heavier steering. CAUTIONS Too much tension in the tow rope could cause damage to your vehicle or the vehicle that is towing. Do not use a rigid tow bar on the front towing eye. Drive off slowly and smoothly without jerking the vehicle that is towing.
Vehicles with automatic transmission CAUTIONS Do not tow your vehicle faster than 50 km/h (30 mph) or further than 50 kilometres (30 miles). On vehicles with a 6DCT450 transmission, do not tow your vehicle faster than 30 km/h (18 mph). If the stated speed or distance is to be exceeded the drive wheels must be lifted clear of the ground. In the event of a mechanical failure of the transmission the drive wheels must be lifted clear of the ground.
164
Maintenance GENERAL INFORMATION
•
Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford Authorised Repairers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialised tools developed specifically for servicing your vehicle.
• •
Washer fluid level. See Washer fluid check (page 180). Tyre pressures (when cold). See Wheels and tyres (page 188). Tyre condition. See Wheels and tyres (page 188).
Monthly checks •
• •
In addition to regular servicing, we recommend that you carry out the following additional checks.
• • • •
WARNINGS Switch the ignition off before touching or attempting adjustment of any kind. Do not touch the electronic ignition system parts after you have switched the ignition on or when the engine is running. The system operates at high voltage.
Engine coolant level (engine cold). See Engine coolant check (page 179). Pipes, hoses and reservoirs for leaks. Power steering fluid level. See Power steering fluid check (page 180). Air conditioning operation. Parking brake operation. Horn operation. Tightness of wheel nuts. See Wheels and tyres (page 188).
OPENING AND CLOSING THE BONNET Opening the bonnet
Keep your hands and clothing clear of the engine cooling fan. Under certain conditions, the fan may continue to run for several minutes after you have switched the engine off.
WARNING
Daily checks
To prevent damage to, or loss of the key, remove the key immediately after opening and swivel the Ford badge back.
• • •
Note: On vehicles with the key free system, use the spare key to open the bonnet.
Exterior lamps. Interior lamps. Warning lamps and indicators.
Check when refuelling • •
Engine oil level. See Engine oil check (page 178). Brake fluid level. See Brake and clutch fluid check (page 180).
165
Maintenance
1 5
4 E78141
2
3
E78142
E78143
Closing the bonnet Note: Make sure that the bonnet is closed properly. Lower the bonnet and allow it to drop from under its own weight for the last 20 – 30 centimetres (8 - 12 inches).
ENGINE OIL CHECK CAUTION Do not use oil additives or other engine treatments. Under certain conditions, they could damage the engine.
178
Maintenance Note: The oil consumption of new engines reaches its normal level after approximately 5 000 kilometres (3 000 miles).
ENGINE COOLANT CHECK Checking the coolant level WARNING
Checking the oil level
Do not allow the fluid to touch your skin or eyes. If this happens, rinse the affected areas immediately with plenty of water and contact your doctor.
CAUTION Make sure that the level is between the MIN and the MAX marks.
CAUTION
Note: Check the level before starting the engine.
Make sure that the level is between the MIN and the MAX marks.
Note: Make sure that your vehicle is on level ground.
Note: Coolant expands when it is hot. The level may therefore extend beyond the MAX mark.
Note: Oil expands when it is hot. The level may therefore extend a few millimetres beyond the MAX mark.
If the level is at the MIN mark, top up immediately.
Remove the dipstick and wipe it with a clean, lint free cloth. Replace the dipstick and remove it again to check the oil level.
Topping up
If the level is at the MIN mark, top up immediately.
WARNINGS Only top up when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down.
Topping up WARNINGS Only top up when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down.
Do not remove the filler cap when the engine is running. Do not remove the filler cap when the engine is hot. Wait for the engine to cool down.
Do not remove the filler cap when the engine is running.
Unscrew the cap slowly. Any pressure will escape slowly as you unscrew the cap.
Remove the filler cap. CAUTION Do not top up further than the MAX mark.
CAUTIONS Do not spill coolant on any part of the engine.
Top up with fluid that meets the Ford specification. See Technical specifications (page 181).
Do not top up further than the MAX mark.
179
Maintenance Top up with fluid that meets the Ford specification. See Technical specifications (page 181).
Top up with fluid that meets the Ford specification. See Technical specifications (page 181).
BRAKE AND CLUTCH FLUID CHECK
POWER STEERING FLUID CHECK Vehicles with 1.4L Duratec-16V (Sigma) or 1.6L Duratec-16V (Sigma) or 1.6L Duratec-16V TiVCT (Sigma) engine
WARNING Do not allow the fluid to touch your skin or eyes. If this happens, rinse the affected areas immediately with plenty of water and contact your doctor.
The fluid level should come up to the MAX mark when the engine is cold.
CAUTION
If it drops below the MIN mark, top up with the specified fluid. See Technical specifications (page 181).
Make sure that the level is between the MIN and the MAX marks.
All except vehicles with 1.4L Duratec-16V (Sigma) or 1.6L Duratec-16V (Sigma) or 1.6L Duratec-16V Ti-VCT (Sigma) engine
Note: The brake and the clutch systems are supplied from the same reservoir. If the level is at the MIN mark, top up immediately.
Topping up
No fluid level checks are necessary.
Remove the filler cap.
WASHER FLUID CHECK
CAUTION The front and rear washer systems are supplied from the same reservoir.
You can use an alternative SAE 5W-30 engine oil, providing it meets the specification defined by WSS-M2C913-B. Note: If you operate your vehicle in temperatures below -20°C, you must not use SAE 10W-40 engine oil. Topping up the oil: If you are unable to find an oil that meets the specification defined by WSS-M2C913-B, you must use SAE 5W-30 (preferred), SAE 5W-40 (except vehicles with E85 fuel) or SAE 10W-40 that meets the specification defined by either ACEA A1/B1 (preferred) or ACEA A3/B3. Using these oils can result in longer engine cranking periods, reduced engine performance, reduced fuel economy and increased emission levels. Capacities Variant
Item
Capacity in litres (gallons)
All
Power assisted steering fluid
Vehicles with a petrol engine except 2.5L Duratec-RS
Fuel tank
55 (12.1)
Vehicles with a 2.5L Duratec-RS engine
Fuel tank
62 (13.6)
Vehicles with a diesel engine
Fuel tank
53 (11.7)
All
Windscreen washer system - with headlamp washers
181
MAX-mark
4.5 (1)
Maintenance Variant
Item
Capacity in litres (gallons)
All
Windscreen washer system - without headlamp washers
3.3 (0.7)
1.4L Duratec-16V
Engine oil - with filter
3.8 (0.8)
1.4L Duratec-16V
Engine oil - without filter
3.5 (0.8)
1.4L Duratec-16V
Cooling system including heating - vehicles with air conditioning
5.5 (1.2)
1.4L Duratec-16V
Cooling system including heating - vehicles without air conditioning
5.2 (1.1)
1.6L Duratec-16V
Engine oil - with filter
1.6L Duratec-16V
Engine oil - without filter
1.6L Duratec-16V
Cooling system including heating - vehicles with air conditioning
5.8 (1.3)
1.6L Duratec-16V
Cooling system including heating - vehicles without air conditioning
5.5 (1.2)
1.6L Duratec-16V Ti-VCT
Engine oil - with filter
4.1 (0.9)
1.6L Duratec-16V Ti-VCT
Engine oil - without filter
1.6L Duratec-16V Ti-VCT
Cooling system including heating
6.0 (1.3)
1.8L Duratec-HE
Engine oil - with filter
4.3 (0.9)
1.8L Duratec-HE
Engine oil - without filter
3.9 (0.9)
1.8L Duratec-HE
Cooling system including heating
6.5 (1.4)
2.0L Duratec-HE
Engine oil - with filter
4.3 (0.9)
2.0L Duratec-HE
Engine oil - without filter
3.9 (0.9)
2.0L Duratec-HE
Cooling system including heating
6.3 (1.4)
182
4.1 (0.9) 3.75 (0.8)
3.75 (0.8)
Maintenance Variant
Item
Capacity in litres (gallons)
2.5L Duratec-ST and 2.5L Duratec-RS
Engine oil - with filter
5.8 (1.3)
2.5L Duratec-ST and 2.5L Duratec-RS
Engine oil - without filter
5.5 (1.2)
2.5L Duratec-ST and 2.5L Duratec-RS
Cooling system including heating
7.1 (1.6)
1.6L Duratorq-TDCi
Engine oil - with filter
3.8 (0.8)
1.6L Duratorq-TDCi
Engine oil - without filter
3.4 (0.7)
1.6L Duratorq-TDCi
Cooling system including heating
7.3 (1.6)
1.8L Duratorq-TDCi
Engine oil - with filter
5.6 (1.2)
1.8L Duratorq-TDCi
Engine oil - without filter
5.0 (1.1)
1.8L Duratorq-TDCi
Cooling system including heating
8.1 (1.8)
2.0L Duratorq-TDCi
Engine oil - with filter
5.5 (1.2)
2.0L Duratorq-TDCi
Engine oil - without filter
5.0 (1.1)
2.0L Duratorq-TDCi
Cooling system including heating
8.4 (1.8)
183
Vehicle care Cleaning the chrome trim
CLEANING THE EXTERIOR
CAUTION
WARNING
Do not use abrasives or chemical solvents. Use soapy water.
If you use a car wash with a waxing cycle, make sure that you remove the wax from the windscreen.
Body paintwork preservation CAUTIONS Some car wash installations use water at high pressure. This could damage certain parts of your vehicle.
CAUTIONS Do not polish your vehicle in strong sunshine. Do not allow polish to touch plastic surfaces. It could be difficult to remove.
Remove the aerial before using an automatic car wash. Switch the heater blower off to prevent contamination of the fresh air filter.
Do not apply polish to the windscreen or rear window. This could cause the wipers to become noisy and they may not clear the window properly.
We recommend that you wash your vehicle with a sponge and lukewarm water containing a car shampoo.
We recommend that you wax the paintwork once or twice a year.
Cleaning the headlamps
CLEANING THE INTERIOR
CAUTIONS Do not scrape the headlamp lenses or use abrasives, alcoholic solvents or chemical solvents to clean them.
Seat belts WARNINGS Do not use abrasives, or chemical solvents to clean them.
Do not wipe the headlamps when they are dry.
Do not allow moisture to penetrate the seat belt retractor mechanism.
Cleaning the rear window CAUTION
Clean the seat belts with interior cleaner or water applied with a soft sponge. Let the seat belts dry naturally, away from artificial heat.
Do not scrape the inside of the rear window or use abrasives or chemical solvents to clean it. Use a clean, lint free cloth or a damp chamois leather to clean the inside of the rear window.
184
Vehicle care Instrument cluster screens, LCD screens, radio screens WARNING Do not use abrasives, alcoholic solvents or chemical solvents to clean them.
REPAIRING MINOR PAINT DAMAGE CAUTION Remove apparently harmless looking substances from the paintwork immediately (e.g. bird droppings, tree resins, insect remains, tar spots, road salt and industrial fall out). You should repair paintwork damage caused by stones from the road or minor scratches as soon as possible. A choice of products is available from your Ford Dealer. Read and follow the manufacturer’s instructions.
185
Vehicle battery To connect the booster cables
USING BOOSTER CABLES CAUTIONS Connect batteries with only the same nominal voltage. Always use booster cables with insulated clamps and adequate size cable. Do not disconnect the battery from the vehicle’s electrical system.
A
C
D
B
E75183
186
A
Flat battery vehicle
B
Booster battery vehicle
C
Positive connection cable
D
Negative connection cable
Vehicle battery 1.
Position the vehicles so that they do not touch one another. 2. Switch off the engine and any electrical equipment. 3. Connect the positive (+) terminal of vehicle B with the positive (+) terminal of vehicle A (cable C). 4. Connect the negative (-) terminal of vehicle B to the ground connection on the left-hand side suspension turret of vehicle A (cable D).
CHANGING THE VEHICLE BATTERY Vehicles with a petrol engine If the battery has been disconnected the vehicle may exhibit some unusual driving characteristics for approximately 8 km (5 miles) after battery reconnection while the engine management system realigns itself with the engine.
CAUTIONS Do not connect to the negative (–) terminal of the flat battery. Make sure that the cables are clear of any moving parts.
To start the engine 1.
Run the engine of vehicle B at moderately high speed.
2. Start the engine of vehicle A. 3. Run both vehicles for a minimum of three minutes before disconnecting the cables. CAUTION Do not switch on the headlamps when disconnecting the cables. The peak voltage could blow the bulbs. Disconnect the cables in the reverse order.
187
Wheels and tyres GENERAL INFORMATION
WARNINGS Do not use snow chains on this type of wheel.
CAUTIONS Use only approved wheel and tyre sizes. Using other sizes could damage the vehicle and will make the National Type Approval invalid.
Do not drive through an automatic car wash. Do not carry out any tyre repairs on a temporary spare wheel.
If you change the diameter of the tyres from that fitted at the factory, the speedometer may not display the correct speed. Take the vehicle to your dealer to have the engine management system reprogrammed.
CAUTION The ground clearance of your vehicle will be reduced. Take care when parking next to a kerb.
A decal with tyre pressure data is located in the driver’s door opening at the B-pillar.
Note: Your vehicle may exhibit some unusual driving characteristics.
Check and set the tyre pressure at the ambient temperature in which you are intending to drive the vehicle and when the tyres are cold.
Vehicle jack WARNINGS The vehicle jack supplied with your vehicle should only be used when changing a wheel in emergency situations.
CHANGING A ROAD WHEEL Locking wheel nuts
Before using the vehicle jack, check that it is not damaged or deformed and that the thread is lubricated and free from foreign matter.
You can obtain a replacement locking wheel nut key and replacement locking wheel nuts from your dealer using the reference number certificate.
Never place anything between the jack and the ground, or the jack and the vehicle.
Vehicles with a temporary spare wheel WARNINGS If the spare wheel differs from the other fitted wheels, these rules must be followed:
Note: Vehicles with a tyre repair kit are not equipped with a vehicle jack or a wheel brace. It is recommended to use a workshop type hydraulic jack for changing between summer and winter tyres.
Do not exceed 80 km/h (50 mph).
Note: Use a jack with a minimum lifting capacity of 1.5 tonnes and a lifting plate with a minimum diameter of 80 millimetres (3.1 inches).
Drive the shortest possible distances. Do not fit more than one spare wheel on your vehicle at any one time.
188
Wheels and tyres Vehicles without tyre repair kit
A
A
Jack
B
Wheel brace
C
Space for locking wheel nut key
Your vehicle jack and wheel brace are located in the spare wheel well.
Jacking and lifting points CAUTION
C
Use only the specified jacking points. If you use other positions, you may damage the body, steering, suspension, engine, braking system or the fuel lines.
B
E105575
A B
E92658
189
Wheels and tyres A
Emergency use only
B
Maintenance Vehicles with side skirts
A
E93184
Indentations in the sills A show the location of the jacking points.
E95345
Removing a road wheel WARNINGS Park your vehicle in such a position that neither the traffic nor you are hindered or endangered. Set up a warning triangle. Make sure that the vehicle is on firm, level ground with the wheels pointing straight ahead. Switch off the ignition and apply the parking brake.
E92932
If your vehicle has a manual transmission, select first or reverse gear. If it has an automatic transmission, select park. Have the passengers leave the vehicle. Secure the diagonally opposite wheel with an appropriate block or wheel chock.
E93020
190
Wheels and tyres WARNINGS Make sure that the arrows on directional tyres point in the direction of rotation when the vehicle is moving forwards. If you have to fit a spare wheel with the arrows pointing in the opposite direction, have the tyre refitted in the correct direction by a properly trained technician. Do not work underneath the vehicle when it is supported only by a jack. Make sure that the jack is vertical to the jacking point and the base is flat on the ground. CAUTION
E71948
Do not lay alloy wheels face down on the ground, this will damage the paint.
2. Install the locking wheel nut key. 3. Slacken the wheel nuts. 4. Jack up the vehicle until the tyre is clear of the ground.
Note: The spare wheel is located under the floor cover in the luggage compartment. 1.
5. Remove the wheel nuts and the wheel.
Insert the flat end of the wheel brace between the rim and the hub cover and carefully remove the hub cap or cover.
Installing a road wheel WARNINGS Use only approved wheel and tyre sizes. Using other sizes could damage the vehicle and will make the National Type Approval invalid. See Technical specifications (page 199). Do not fit run flat tyres on vehicles that were not originally fitted with them. Please contact your dealer for more details regarding compatibility. CAUTION Do not install alloy wheels using wheel nuts designed for use with steel wheels.
191
Wheels and tyres Note: Make sure the wheel and hub contact surfaces are free from foreign matter.
5. Lower the vehicle and remove the jack. 6. Fully tighten the wheel nuts in the sequence shown. See Technical specifications (page 199). 7. Install the hub cap or cover using the ball of your hand.
Note: Make sure that the cones on the wheel nuts are against the wheel. 1. Install the wheel. 2. Install the wheel nuts finger tight.
WARNING Have the wheel nuts checked for tightness and the tyre pressure checked as soon as possible. Note: If the spare wheel is different in size or construction to the road wheels, have this replaced as soon as possible.
TYRE CARE
E71948 3. Install the locking wheel nut key. E70415
1
To make sure the front and rear tyres of your vehicle wear evenly and last longer, we recommend that you swap the tyres from front to rear and vice versa at regular intervals of between 5 000 and 10 000 km (3 000 and 6 000 miles).
4
3
CAUTION
5
Do not scrub the sidewalls of the tyres when you are parking.
2
If you have to mount a kerb, do so slowly and approach it with the wheels at right-angles to the kerb.
E75442 4. Partially tighten the wheel nuts in the sequence shown.
192
Wheels and tyres •
Examine the tyres regularly for cuts, foreign objects and uneven wear of the tread. Uneven wear could mean that the wheel alignment is outside specification. Check the tyre pressures (including the spare) when cold, every two weeks.
•
TYRE REPAIR KIT Your vehicle may not have a spare tyre. In this case it will have an emergency tyre repair kit that can be used to repair one flat tyre.
• •
The tyre repair kit is located in the spare wheel well.
•
General information WARNINGS Depending on the type and extent of tyre damage, some tyres can only be partially sealed or not sealed at all. Loss of tyre pressure can affect vehicle handling, leading to loss of vehicle control.
Drive with caution and avoid making sudden steering or driving manoeuvres, especially if the vehicle is heavily loaded or you are towing a trailer. The kit will provide you with an emergency temporary repair, enabling you to continue your journey to the next vehicle or tyre dealer, or to drive a maximum distance of 200 kilometres (125 miles). Do not exceed a maximum speed of 80 km/h (50 mph). Keep the kit out of the reach of children. Only use the kit when the ambient temperature is between –30°C (-22°F) and +70°C (+158°F).
Using the tyre repair kit WARNINGS Compressed air can act as an explosive or propellant. Never leave the tyre repair kit unattended while in use.
Do not use the tyre repair kit if the tyre has already been damaged as a result of being driven under inflated.
CAUTION Do not keep the compressor operating for more than 10 minutes.
Do not try to seal damage other than that located within the visible tread of the tyre.
Note: Use the tyre repair kit only for the vehicle with which it was supplied.
Do not try to seal damage to the tyre’s sidewall.
• The tyre repair kit seals most tyre punctures [with a diameter of up to six millimetres (1/4 inch)] to temporarily restore mobility.
•
Observe the following rules when using the kit:
•
193
Park your vehicle at the roadside so that you do not obstruct the flow of traffic and so that you are able to use the kit without being in danger. Apply the parking brake, even if you have parked on a level road, to make sure that the vehicle will not move. Do not attempt to remove foreign objects like nails or screws penetrating the tyre.
Wheels and tyres •
•
•
Leave the engine running while the kit is in use, but not if the vehicle is in an enclosed or poorly ventilated area (for example, inside a building). In these circumstances, switch the compressor on with the engine turned off. Replace the sealant bottle with a new one before the expiry date (see top of bottle) is reached. Inform all other users of the vehicle that the tyre has been temporarily sealed with the tyre repair kit and make them aware of the special driving conditions to be observed.
WARNINGS Watch the sidewall of the tyre. If any cracks, bumps or similar damage appear, turn off the compressor and let the air out by means of the pressure relief valve B. Do not continue driving with this tyre. The sealant contains natural rubber latex. Avoid contact with skin and clothing. If this happens, rinse the affected areas immediately with plenty of water and contact your doctor. If the tyre inflation pressure does not reach 1.8 bar (26 psi) within seven minutes, the tyre may have suffered excessive damage, making a temporary repair impossible. In this case, do not continue driving with this tyre.
Inflating the tyre WARNINGS Check the sidewall of the tyre prior to inflation. If there are any cracks, bumps or similar damage, do not attempt to inflate the tyre.
CAUTION Screwing the bottle onto the bottle holder will pierce the seal of the bottle. Do not unscrew the bottle from the holder as the sealant will escape.
Do not stand directly beside the tyre while the compressor is pumping.
194
Wheels and tyres A
K
B J C I D H
E G
F E94973
A
Protective cap
B
Pressure relief valve
C
Hose
D
Orange cap
195
Wheels and tyres E
Bottle holder
F
Pressure gauge
G
Power plug with cable
H
Compressor switch
I
Label
J
Bottle lid
K
Sealant bottle
1. Open the lid of the tyre repair kit. 2. Peel off the label I showing the maximum permissible speed of 80 km/h (50 mph) from the casing and attach it to the instrument panel in the driver’s field of view. Make sure the label does not obscure anything important. 3. Take the hose C and the power plug with cable G out of the kit. 4. Unscrew the orange cap D and the bottle lid J. 5. Screw the sealant bottle K clockwise into the bottle holder E fully tight. 6. Remove the valve cap from the damaged tyre. 7. Detach the protective cap A from the hose C and screw the hose C firmly onto the valve of the damaged tyre. 8. Make sure that the compressor switch H is in position 0. 9. Insert the power plug G into the cigar lighter socket or auxiliary power socket. See Cigar lighter (page 111). See Auxiliary power sockets (page 112). 10. Start the engine. 11. Move the compressor switch H to position 1.
12.
Inflate the tyre for no longer than seven minutes to an inflation pressure of minimum 1.8 bar (26 psi) and a maximum of 3.5 bar (51 psi). Move the compressor switch H to position 0 and check the current tyre pressure with pressure gauge F.
13.
Remove the power plug G from the cigar lighter socket or auxiliary power socket.
14.
Quickly unscrew the hose C from the tyre valve and replace the protective cap A. Fasten the valve cap again.
15.
Leave the sealant bottle K in the bottle holder E. Make sure the kit, the bottle lid and the orange cap are stored safely, but still easily accessible in the vehicle. The kit will be required again when you check the tyre pressure. Immediately drive approximately three kilometres (two miles) so that the sealant can seal the damaged area.
16.
17.
Note: When pumping in the sealant through the tyre valve, the pressure may rise up to 6 bar (87 psi) but will drop again after about 30 seconds.
196
Wheels and tyres 8. Drive to the nearest tyre specialist to get the damaged tyre replaced. Before the tyre is removed from the rim, inform your tyre dealer that the tyre contains sealant. Renew the kit as soon as possible after it has been used once.
WARNING If you experience heavy vibrations, unsteady steering behaviour or noises while driving, reduce your speed and drive with caution to a place where it is safe for you to stop the vehicle. Recheck the tyre and its pressure. If the tyre pressure is less than 1.3 bar (19 psi) or if there are any cracks, bumps or similar damage visible, do not continue driving with this tyre.
Note: Remember that emergency roadside tyre repair kits only provide temporary mobility. Regulations concerning tyre repair after usage of tyre repair kit may differ from country to country. You should consult a tyre specialist for advice.
Checking the tyre pressure 1.
2. 3.
4. 5.
6.
Stop the vehicle after driving approximately three kilometres (two miles). Check, and where necessary, adjust the pressure of the damaged tyre. Attach the kit and read the tyre pressure from the pressure gauge F. If the pressure of the sealant-filled tyre is 1.3 bar (19 psi) or more, adjust it to the specified pressure. See Technical specifications (page 199). Follow the inflation procedure once again to top up the tyre. Check the tyre pressure again from the pressure gauge F. If the tyre pressure is too high, deflate the tyre to the specified pressure using the pressure relief valve B. Once you have inflated the tyre to its correct tyre pressure, move the compressor switch H to position 0, remove the power plug G from the socket, unscrew the hose C, fasten the valve cap and replace the protective cap A.
WARNING Before driving, make sure the tyre is adjusted to the recommended inflation pressure. See Technical specifications (page 199). Monitor the tyre pressure until the sealed tyre is replaced. Empty sealant bottles can be disposed of together with normal household waste. Return remains of sealant to your dealer or dispose of it in compliance with local waste disposal regulations.
USING WINTER TYRES CAUTION Make sure that you use the correct wheel nuts for the type of wheel the winter tyres are fitted to. If winter tyres are used, make sure that the tyre pressures are correct. See Technical specifications (page 199).
7. Leave the sealant bottle K in the bottle holder E and store the kit away safely in its original location.
197
Wheels and tyres USING SNOW CHAINS
WARNINGS Do not drive on significantly under-inflated tyres. This may cause the tyres to overheat and fail. Under-inflation reduces fuel efficiency, tyre tread life and may also affect your ability to drive the vehicle safely.
WARNINGS Do not exceed 50 km/h (30 mph). Do not use snow chains on snow-free roads.
CAUTIONS Do not bend or damage the valves when you are inflating the tyres.
Only fit snow chains to specified tyres. See Technical specifications (page 199).
Have tyres installed by properly trained technicians.
CAUTION If your vehicle is fitted with wheel trims, remove them before fitting snow chains.
The Deflation Detection System will alert you if there is a change of air pressure in any tyre. It does this by using the ABS sensors to detect the rolling circumference of the wheels. When the circumference changes, this indicates low pressure in a tyre, a warning message is displayed in the information display and the message indicator will illuminate. See Information messages (page 89).
Note: The ABS will continue to operate normally. Only use small link snow chains. Only use snow chains on the front wheels.
Vehicles with stability control (ESP)
Apart from a too low tyre pressure or a damaged tyre, the following situations can affect the rolling circumference: • Vehicle load is uneven. • When using a trailer or travelling up and down an incline. • Using snow chains. • Driving on soft surfaces such as snow or mud.
Vehicles with stability control (ESP) may exhibit some unusual driving characteristics which can be avoided by switching the system off. See Using stability control (page 134).
TYRE PRESSURE MONITORING SYSTEM
Note: The system will still function correctly, but there may be an increased detection time.
WARNINGS The system does not relieve you of your responsibility to regularly check the tyre pressures.
If a low pressure warning message is displayed in the information display, check the tyre pressures as soon as possible and inflate them to the recommended pressure. See Technical specifications (page 199).
The system will only provide a low tyre pressure warning. It will not inflate the tyres.
198
Wheels and tyres If this happens frequently, have the cause determined and rectified as soon as possible.
Type 2 instrument cluster
System reset
2. Press and hold the SET/RESET button until the message Tyre Pressure set appears.
1.
Note: Do not reset the system when the vehicle is moving.
Using the multifunction lever, navigate to 'SET' > T. Pres.
Note: You should reset the system following any adjustment to the tyre pressures or any changing of tyres.
Type 3 instrument cluster
Note: Turn the ignition on.
2. Press and hold the SET/RESET button until the message Tyre Pressure set appears.
1.
Using the multifunction lever, navigate to hold 'SET' to set Tyre Pres.
TECHNICAL SPECIFICATIONS Wheel nut torque Wheel type
Nm (Ib-ft)
All
130 (96)
Tyre pressures (cold tyres) Up to 80 km/h (50 mph) Normal load Variant
All
Tyre size
T125/85 R 16
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
4.2 (61)
4.2 (61)
4.2 (61)
4.2 (61)
Except convertible, Focus ST and Focus RS Up to 160 km/h (100 mph) Normal load Variant
All
Tyre size
195/65 R 15
*
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.1 (31)
2.3 (33)
2.4 (35)
2.8 (41)
199
Wheels and tyres Normal load Variant
Tyre size
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
All
205/50 R 17
2.3 (33)
2.3 (33)
2.5 (36)
2.8 (41)
All
225/40 R 18
2.3 (33)
2.3 (33)
2.5 (36)
2.8 (41)
Vehicles with a petrol engine
205/55 R 16
*
2.1 (31)
2.3 (33)
2.4 (35)
2.8 (41)
Vehicles with a diesel engine
205/55 R 16
*
2.3 (33)
2.3 (33)
2.4 (35)
2.8 (41)
*
Only fit snow chains to specified tyres.
Continuous speed in excess of 160 km/h (100 mph) Normal load Variant
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
195/65 R 15
2.4 (35)
2.3 (33)
2.6 (38)
3.0 (44)
All
205/50 R 17
2.5 (36
2.3 (33)
2.7 (39)
3.0 (44)
All
225/40 R 18
2.5 (36
2.3 (33)
2.7 (39)
3.0 (44)
All
205/55 R 16
2.4 (35)
2.3 (33)
2.6 (38)
3.0 (44)
All
Tyre size
Convertible Up to 160 km/h (100 mph) Normal load Variant
Tyre size
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
All
205/55 R 16
*
2.3 (33)
2.5 (36
2.3 (33)
2.5 (36
All
205/50 R 17
2.3 (33)
2.5 (36
2.3 (33)
2.5 (36
All
225/40 R 18
2.3 (33)
2.3 (33)
2.3 (33)
2.5 (36
*
Only fit snow chains to specified tyres.
200
Wheels and tyres
Continuous speed in excess of 160 km/h (100 mph) Normal load Variant
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
205/55 R 16
2.3 (33)
2.5 (36)
2.5 (36)
2.7 (39)
All
205/50 R 17
2.3 (33)
2.5 (36)
2.5 (36)
2.7 (39)
All
225/40 R 18
2.3 (33)
2.3 (33)
2.5 (36)
2.7 (39)
All
Tyre size
Full load
Focus ST Up to 160 km/h (100 mph) Normal load Variant
Tyre size
*
All
205/55 R 16
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.3 (33)
2.3 (33)
2.3 (33)
2.3 (33)
*
Only fit snow chains to specified tyres.
Continuous speed in excess of 160 km/h (100 mph) Normal load Variant
All
Tyre size
205/55 R 16
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.5 (36)
2.3 (33)
2.7 (39)
2.3 (33)
Up to 190 km/h (118 mph) Normal load Variant
All
Tyre size
225/40 R 18
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.3 (33)
2.1 (30)
2.3 (33)
2.1 (30)
201
Wheels and tyres
Continuous speed in excess of 190 km/h (118 mph) Normal load Variant
All
Tyre size
225/40 R 18
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.6 (38)
2.3 (33)
2.8 (41)
2.4 (35)
Focus RS Winter tyres - up to 210 km/h (130 mph) Normal load Variant
All
Tyre size
205/50 R 17
*
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.5 (36)
2.3 (33)
2.5 (36)
2.3 (33)
*
Only fit snow chains to specified tyres.
Winter tyres - continuous speed in excess of 210 km/h (130 mph) up to 240 km/h (150 mph) Normal load Variant
All
Tyre size
205/50 R 17
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.7 (39)
2.5 (36)
2.8 (41)
2.6 (38)
Up to 220 km/h (137 mph) Normal load Variant
All
Tyre size
235/35 ZR 19
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
2.5 (36)
2.3 (33)
2.7 (39)
2.5 (36)
202
Wheels and tyres
Continuous speed in excess of 220 km/h (137 mph) Normal load Variant
The vehicle identification number is stamped into the floor panel on the right-hand side, beside the front seat. It is also shown on the left-hand side of the instrument panel.
The vehicle identification number and maximum weights are shown on a plate located on the lock side of the passenger door aperture at the bottom.
Wheel centre – centre of tow ball - fixed tow ball
907 (35.7)
C
Wheel centre – centre of tow ball - detachable tow ball
923 (36.3)
D
Centre of tow ball – side member
517 (20.4)
E
Distance between side members
1 034 (40.7)
F
Centre of tow ball – centre 1. attachment point - fixed tow ball
407 (16)
F
Centre of tow ball – centre 1. attachment point detachable tow ball
423 (16.7)
G
Centre of tow ball – centre 2. attachment point - fixed tow ball
709 (27.9)
G
Centre of tow ball – centre 2. attachment point detachable tow ball
723 (28.5)
All measurements refer to towing equipment officially released by Ford. 4-door Item
Dimension description
Dimension in mm (inches)
A
Bumper – end of tow ball
94 (3.7)
B
Attachment point – centre of tow ball
48.2 (1.9)
C
Wheel centre – centre of tow ball
1 045 (41.1)
D
Centre of tow ball – side member
517 (20.4)
209
Technical specifications Item
Dimension description
Dimension in mm (inches)
E
Distance between side members
1 034 (40.7)
F
Centre of tow ball – centre 1. attachment point
424 (16.7)
G
Centre of tow ball – centre 2. attachment point
724 (28.5)
All measurements refer to towing equipment officially released by Ford. Estate Item
Dimension description
Dimension in mm (inches)
A
Bumper – end of tow ball
104 - 121 (4.1 - 4.8)
B
Attachment point – centre of tow ball
55 - 95 (2.2 - 3.7)
C
Wheel centre – centre of tow ball
1 057 (41.6)
D
Centre of tow ball – side member
594 (23.4)
E
Distance between side members
1 188 (46.8)
F
Centre of tow ball – centre 1. attachment point
433 (17)
G
Centre of tow ball – centre 2. attachment point
683 (26.9)
All measurements refer to towing equipment officially released by Ford. Convertible Item
Dimension description
Dimension in mm (inches)
A
Bumper – end of tow ball
95 (3.7)
B
Attachment point – centre of tow ball
6 (0.2)
C
Wheel centre – centre of tow ball
1 064 (41.9)
210
Technical specifications Item
Dimension description
Dimension in mm (inches)
D
Centre of tow ball – side member
517 (20.4)
E
Distance between side members
1 034 (40.7)
F
Centre of tow ball – centre 1. attachment point
443 (17.4)
G
Centre of tow ball – centre 2. attachment point
743 (29.3)
All measurements refer to towing equipment officially released by Ford.
211
Telephone GENERAL INFORMATION
TELEPHONE SETUP Phonebook
CAUTION Using the system with the engine off will drain the battery.
Note: It may be necessary to confirm phonebook access to the Bluetooth system via the mobile phone.
This section describes the functions and features of the Bluetooth mobile phone hands free system.
After start up access to the phonebook list can be delayed for several minutes, depending upon the size.
The Bluetooth mobile phone part of the system provides interaction with the audio or navigation system and your mobile phone. It allows you to use the audio or navigation system to make and receive calls without having to use your mobile phone.
Phonebook categories Depending on your phonebook entry, different categories can be displayed in the audio unit. For example:
Compatibility of phones
M
Mobile
CAUTION
O
Office
As no common agreement exists, mobile phone manufacturers are able to implement a variety of profiles in their Bluetooth devices. Because of this, an incompatibility can occur between the phone and hands-free system, which in some cases may significantly degrade the system performance. To avoid this situation, only recommended phones should be used.
H
Home
F
Fax
Note: Entries may be displayed without a category attachment. The category can also be indicated as an icon: Phone
Please visit the website www.fordmobile-connectivity.com for full details.
E87990
Mobile E87991
Phones with Symbian operating system
Home E87992
Note: Certain phones require a special file to be installed to enable full phonebook access via Bluetooth.
Office E87993
This is referred to as a SIS file and will be available to download via the Ford website www.fordmobile-connectivity.com.
Fax E87994
212
Telephone Making a phone an active phone
Handling of phones Up to six Bluetooth devices can be bonded to the vehicle system.
When using the system for the first time, no phone is connected to the system.
Note: If there is an ongoing call when the phone in use is selected as the new active phone, the call is transferred to the vehicle audio system.
After switching on the ignition and the audio unit, the Bluetooth phone must be bonded to the system.
Note: Even if connected to the car system, your phone can still be used in the usual way.
Bluetooth phone After bonding a Bluetooth phone to the system, this becomes the active phone. For further information refer to the phone menu.
Requirements for Bluetooth connection
Select the phone from the active phone menu.
The following are required before a Bluetooth phone connection can be made.
Turning the ignition and radio or navigation unit back on again, the last active phone is picked up by the system.
1.
Note: In some cases the Bluetooth connection must also be confirmed on the phone.
Bond another Bluetooth phone 2.
Bond a new Bluetooth phone as described in the requirements for a Bluetooth connection.
3. 4. 5.
Phones stored in the system are accessible by using the phone list on the audio unit. Note: A maximum of six devices may be bonded. If six Bluetooth devices have already been bonded, one of these has to be debonded in order to bond a new device.
The Bluetooth feature must be activated on the phone and on the audio unit. Make sure the Bluetooth menu option in the audio unit is set to ON. For information on phone settings, refer to your phone user guide. The private mode must not be activated on the Bluetooth phone. Search for audio device. Select Ford Audio. Enter the code number shown on the vehicle display using the phone keypad. If no code number is shown on the display, enter the Bluetooth PIN number 0000 using the phone keypad. Now enter the Bluetooth PIN number shown on the vehicle display.
Note: A phone call will be disconnected if the audio unit is switched off. If the ignition key is turned to the off position the phone call will remain in progress.
BLUETOOTH SETUP Before you can use your telephone with your vehicle it must be bonded to the vehicle telephone system.
213
Telephone TELEPHONE CONTROLS
Making a call
Remote control
Dialling a number using voice control
Voice and mode button
Phone numbers can be dialled using voice control. See Telephone commands (page 231).
1
Dialling a number using the address book You can access your phone address book via Bluetooth. The entries will appear in the unit display. 1.
2
2. Press the MENU button. 3. Keep pressing the MENU button until PHONEBOOK appears. 4. Press the seek buttons to select the desired phone number.
E87661
1
Voice button
2
Mode button
Press the PHONE or the call accept button.
Note: Press and hold the seek button to skip to the next letter in the alphabet. 5. Press the PHONE or the call accept button to dial the selected phone number.
Incoming calls can be accepted by pressing the MODE button once. Press the button again to end the call.
Dialling a number using the address book - Sony radio
USING THE TELEPHONE VEHICLES WITHOUT: NAVIGATION SYSTEM
You can access your phone address book via Bluetooth. The entries will appear in the unit display.
This chapter describes the phone functions of the audio unit.
Press the PHONE button. 2. Press the seek button until the phone book is shown. 3. Press the up/down arrow buttons to select the desired phone number. 1.
Note: Refer to your audio guide for details of the controls. An active phone must be present. Even if connected to the audio unit, your phone can still be used in the usual way.
Note: Press and hold the up/down arrow buttons to skip to the next letter in the alphabet.
Note: You can exit the phone menu by pressing any source button CD, AM/FM or AUX.
4. Press the PHONE or the call accept button to dial the selected phone number.
214
Telephone Dialling a number using the telephone keypad
Redialling a number - Sony radio 1.
Press the PHONE or the call accept button. 2. Press the seek button until the desired list is displayed.
If you have an audio unit with a telephone keypad (buttons 0-9, * and #): 1.
Press the call accept button. Press the PHONE button if you have a Sony radio. 2. Dial the number using the telephone keypad on the audio unit. 3. Press the call accept button.
Note: If the active phone does not provide a call out list, the last outgoing call number/entry can be redialled. 3. Press the up/down buttons to select the desired phone number. 4. Press the PHONE or the call accept button to dial the phone number.
Note: If you enter an incorrect digit whilst entering a phone number, press the seek left button to erase the last digit. A long press will erase the complete string of digits.
Redialling the last dialled number Sony radio
Press and hold 0 to enter a + digit.
1. Press the call accept button. 2. Press the call accept button a second time to dial the number.
Ending a call Calls can be ended by pressing the call reject button.
Receiving an incoming call
Audio units without a telephone keypad can also end a call by pressing either PHONE, CD, AM/FM or ON/OFF, or by pressing the MODE button on the remote control
Accepting an incoming call Incoming calls can be accepted by pressing either the call accept button, the PHONE button or the MODE button on the remote control.
Redialling a number 1.
Rejecting an incoming call
Press the PHONE or the call accept button.
Incoming calls can be rejected by pressing the call reject button.
2. Press the MENU button. 3. Select the CALL OUT list or the CALL IN list. On some audio units, select the MISSED, INCOMING or OUTGOING calls list.
Audio units without a telephone keypad can also reject a call by pressing either PHONE, CD, AM/FM or ON/OFF.
Receiving a second incoming call
Note: If the active phone does not provide a call out list, the last outgoing call number/entry can be redialled.
Note: The second incoming call function must be activated in your phone.
4. Press the seek button on the audio unit. 5. Press the PHONE or the call accept button to dial the desired phone number.
If there is an incoming call whilst there is an ongoing call, a beep will be heard and you will have the option to end the active call and to accept the incoming call.
215
Telephone Accepting a second incoming call
Using the audio unit menu
Second incoming calls can be accepted by pressing either the call accept button, the PHONE button, or the MODE button on the remote control.
Note: After bonding a phone to the system, this becomes the active phone.
Rejecting a second incoming call
2. Press the MENU button on the audio unit. 3. Select the ACTIVE PHONE option on the audio unit. 4. Scroll through the different stored phones by using the seek buttons to display the bonded phones. 5. Press the MENU button to select the phone which is to be the active phone.
1.
Second incoming calls can be rejected by pressing the call reject button. Units without a telephone keypad can also reject a second incoming call by pressing the CD button, or the AM/FM button.
Muting the microphone During a call, it is possible to mute the microphone. Whilst muted, confirmation will appear in the display.
Press the PHONE or call accept button.
Debonding a bonded phone
Audio units with green call accept button
A bonded phone can be deleted from the system at any time, unless a phone call is in progress.
Press the call accept button. Press the button once again to turn this function off.
1.
Audio units without green call accept button
Press the PHONE or call accept button.
2. Press the MENU button on the audio unit. 3. Select the DEBOND option on the audio unit. 4. Scroll through the different phones by using the seek buttons and display the phone to be debonded. 5. Press the MENU button to select the phone which is to be debonded.
Press the seek up or down button. Press the button once again to turn this function off.
Changing the active phone Note: Phones must be bonded to the system before they can be made active.
Debonding a bonded phone Sony radio
Using the station storage button Note: This process is only for audio units without a telephone keypad.
A bonded phone can be deleted from the system at any time, unless a phone call is in progress.
Press the PHONE button on the audio unit. 2. Press the preset number required (using the station preset buttons 1 6). 1.
1.
Press the PHONE button. 2. Press the up/down arrow buttons until you reach the DEBOND option.
216
Telephone Rejecting an incoming call
3. Scroll through the different phones by using the seek buttons and display the phone to be debonded. 4. Press the OK button to be debond.
Incoming calls can be rejected by pressing either the call reject button, the CD or AM/FM buttons on the unit, or by using the REJECT option in the menu.
USING THE TELEPHONE VEHICLES WITH: NAVIGATION SYSTEM
Receiving a second incoming call Note: The second incoming call function must be activated in your phone.
This chapter describes the phone functions of the Navigation System.
If there is an incoming call, whilst there is an ongoing call, a beep will be heard and you will have the option to end the active call and to accept the incoming call.
Note: Refer to your Navigation System guide for details of the controls. An active phone must be present.
Accepting a second incoming call
Even if connected to the Navigation System, your phone can still be used in the usual way.
Second incoming calls can be accepted by pressing either the call accept button, the MODE button on the remote control, the PHONE button on the unit or by using the ACCEPT option in the menu.
Making a call Dialling a number
Note: This will cancel the ongoing call.
Phone numbers can be dialled using voice control. See Voice control (page 219).
Rejecting a second incoming call Second incoming calls can be rejected by pressing either the call reject button, or one of the following buttons on the unit: CD, AM/FM.
Ending a call Calls can be ended by pressing either the END button, the MODE button on the remote switch or the ON/OFF button on the navigation system.
Muting the microphone During a call, it is possible to mute the microphone. Whilst muted, confirmation will appear in the display.
Redialling a number 1.
Press the PHONE button on the unit.
2. Select REDIAL.
DVD navigation units
Receiving an incoming call
Press the mute button (symbol of a microphone with a line through it). Press the button once again to turn this function off.
Accepting an incoming call Incoming calls can be accepted by pressing either the call accept button, the MODE button on the remote control, the PHONE button on the unit or by using the ACCEPT option in the menu.
217
Telephone CD navigation units Press the microphone mute button. Press the button once again to turn this function off.
Changing the active phone Note: Phones must be bonded to the system before they can be made active. Note: After bonding a phone to the system, this becomes the active phone. 1.
Press the PHONE button on the unit. 2. Using the BT SETTINGS option in the menu, select the active phone from the list.
Debonding a bonded phone A bonded phone can be deleted from the system at any time, unless a phone call is in progress. 1.
Press the PHONE button on the unit. 2. Select the BT SETTINGS option in the menu. 3. Select the DEBOND option in the menu. 4. Select the phone from the list.
218
Voice control System response
PRINCIPLE OF OPERATION
As you work through a voice session the system will prompt you with a beep tone each time the system is ready to proceed.
CAUTION Using the system with the engine off will drain the battery.
Do not try to give any commands until the beep tone has been heard. The voice control system will repeat each spoken command back to you.
Voice recognition enables operation of the system without the need to divert your attention from the road ahead in order to change settings, or receive feedback from the system.
If you are not sure how to continue say "HELP" for assistance or "CANCEL" if you do not wish to continue.
Whenever you issue one of the defined commands with the system active, the voice recognition system converts your command into a control signal for the system. Your inputs take the form of dialogues or commands. You are guided through these dialogues by announcements or questions.
The "HELP" function provides only a subset of the available voice commands. Detailed explanations of all possible voice commands can be found on the following pages.
Voice commands All voice commands should be given using a natural speaking voice, as if speaking to a passenger or on the phone. Your voice level should be dependant on the surrounding noise level inside or outside the vehicle but do not shout.
Please familiarise yourself with the functions of the system before using voice recognition.
Supported commands The voice control system allows you to control the following vehicle functions:
USING VOICE CONTROL
•
Bluetooth phone
•
radio
•
CD Player/CD Changer
•
external device (USB)
•
external device (iPod)
•
SD card
•
automatic climate control
<> indicates a number or stored name tag to be inserted by the user.
•
navigation system (DVD units only refer to separate DVD navigation handbook).
Short cuts
System operation The order and content of the voice controls are given in the following lists. The tables show the sequence of user voice commands and system responses for each available function.
There are a number of voice command short cuts available, which allow you to control some vehicle features without having to follow the complete command menu. These are:
Note: The voice control system is language specific. If you require the system to operate in another language please consult your dealer.
219
Voice control •
• •
• • • •
Name tag
phone: "MOBILE NAME", "DIAL NUMBER", "DIAL NAME", and "REDIAL" CD player/CD changer: "DISC" and "TRACK" automatic climate control: "TEMPERATURE", "AUTO MODE", "DEFROSTING/DEMISTING ON" and "DEFROSTING/DEMISTING OFF" radio: "TUNE NAME" external device (USB): "TRACK" external device (iPod): "TRACK" SD card: "TRACK".
The name tag functionality can support the phone, audio and navigation features by using the "STORE NAME" function. You can assign name tags to items such as favourite radio stations and personal phone contacts. See Audio unit commands (page 220). See Telephone commands (page 231). See Navigation system commands (page 235). •
Store up to 20 name tags per function.
•
The average recording time for each name tag is approximately 2-3 seconds.
Start communicating with the system
AUDIO UNIT COMMANDS
Before you can start talking to the system you first have to press the VOICE or MODE button for each operation and wait until the system answers with a beep. See Voice control (page 45).
CD Player You can control playback directly by voice control.
Press the button again to cancel the voice session.
Overview The overview below shows the available voice commands. The following lists will give further information about the complete command menu in selected examples.
"CD PLAYER"
"HELP" "PLAY" *
"TRACK"
"SHUFFLE ALL" "SHUFFLE FOLDER"
**
"SHUFFLE OFF" "REPEAT FOLDER"
220
**
Voice control "CD PLAYER"
"REPEAT TRACK" "REPEAT OFF" * Can be used as a shortcut. ** Only available if the CD contains audio data files like MP3 or WMA. Track You can choose a track on your CD directly. Steps
